Tesis doctoral
UNIVERSIDAD DE GRANADA
DEPARTAMENTO DE INGENIERIA CIVIL
THE USE OF PHOTOVOLTAIC SOLAR ENERGY AS AN ENERGY SOURCE IN THE RESIDENTIAL
HOUSING SECTOR
USO DE LA ENERGÍA SOLAR FOTOVOLTAICA COMO FUENTE PARA EL SUMINISTRO DE ENERGIA
ELECTRICA EN EL SECTOR RESIDENCIAL
Eulalia Jadraque Gago
Granada, 2011
Editor: Editorial de la Universidad de GranadaAutor: Eulalia Jadraque GagoD.L.: GR 2738-2011ISBN: 978-84-694-3563-2
THE USE OF PHOTOVOLTAIC SOLAR ENERGY AS AN ENERGY SOURCE IN THE RESIDENTIAL HOUSING
SECTOR
USO DE LA ENERGÍA SOLAR FOTOVOLTAICA COMO FUENTE PARA EL SUMINISTRO DE ENERGIA
ELECTRICA EN EL SECTOR RESIDENCIAL
Eulalia Jadraque Gago
Granada, 2011
TESIS DOCTORAL
Para la obtención del
GRADO DE DOCTOR EUROPEO POR LA UNIVERSIDAD DE GRANADA
Directores
Javier Ordóñez García
Antonio Espín Estrella
UNIVERSIDAD DE GRANADA
DEPARTAMENTO DE INGENIERIA CIVIL
THE USE OF PHOTOVOLTAIC SOLAR ENERGY AS AN ENERGY SOURCE IN THE RESIDENTIAL HOUSING SECTOR
USO DE LA ENERGÍA SOLAR FOTOVOLTAICA COMO FUENTE PARA EL SUMINISTRO DE ENERGIA ELECTRICA EN EL
SECTOR RESIDENCIAL
Fdo. Dª. Eulalia Jadraque Gago
Granada, 2011
Directores
UNIVERSIDAD DE GRANADA
DEPARTAMENTO DE INGENIERIA CIVIL
Fdo. D. Javier Ordóñez García Doctor Ingeniero de Caminos, Canales y Puertos Departamento de Ingeniería Civil Universidad de Granada
Fdo. D. Antonio Espín Estrella Doctor Ingeniero Industrial Departamento de Ingeniería Civil Universidad de Granada
Memoria presentada por Dª. Eulalia Jadraque Gago para aspirar al grado de Doctor Europeo por la Universidad de Granada
TRIBUNAL DE TESIS
TESIS DOCTORAL
Memoria presentada por Dª. Eulalia Jadraque Gago para aspirar al grado de Doctor Europeo por la Universidad de Granada
Presidente: Fdo.:
Secretario: Fdo.:
Vocal: Fdo.:
Vocal: Fdo.:
Vocal: Fdo.:
Granada, 2011
A María y Sara
“Nuestra ignorancia no es tan grande
como nuestra incapacidad
para utilizar lo que sabemos”
M. King Hubbert (Geofísico y autor de la Teoría del Cenit)
Agradecimientos
Esta tesis es fruto de mucho trabajo que no se podría haber llevado a cabo si no es
por el apoyo de todas las personas que me han rodeado durante estos inolvidables años
de aprendizaje.
Mi gratitud más sincera a mis dos directores de tesis: Javier Ordóñez García y
Antonio Espín Estrella, especialmente a Javier por haber estado siempre ahí desde el
principio de todo, por su orientación y disposición incondicional. Es una suerte haber
podido trabajar con ambos, por lo mucho que he aprendido y porque sin su ayuda no
habría podido completar mi camino para obtener el grado de doctor. A mis compañeros
Francisco Javier Alegre Bayo, Germán Martínez Montes, han hecho una gran labor
crítica y de supervisión, ayudando a aumentar en gran medida la calidad de esta tesis y
de las publicaciones que de ella se han derivado. A Begoña.
A la Edinburgh Napier University y al Transport Research Institute (TRI) por
haberme permitido realizar una parte de esta tesis. Al profesor Tariq Muneer por su
inestimable ayuda y paciencia y también a su familia. A mis compañeros en Edimburgo:
Saioa Etxebarria-Berrizbeitia, Yieng Wei Tham, Yasser Aldali. A Jitka Mohelnikova,
Sarah McCormack y Harris Kambezidis.
A la empresa Añil Construcciones y Servicios, S.A. por financiar una parte de la
investigación.
A Mónica, Mª José y Paz por infundirme ánimos y por su amistad. A Pamela Faber.
A Jesús Garrido, José Manuel Poyatos, Miguel Ángel Gómez y Antonio Peña.
A mi familia, especialmente a mi madre por ser el mayor apoyo que he tenido para
cada una de las metas que he trazado en mi vida, y a quien quiero dedicar esta tesis.
Gracias a mi hija Sara por existir, porque basta una sonrisa para darle sentido a tanto
esfuerzo y porque en estos años me ha enseñado a valorar lo que es realmente
importante en la vida también a ella le dedico esta tesis.
TABLA DE CONTENIDOS
RESUMEN 1
ABSTRACT 3
ESTRUCTURA DE TESIS 5
Capitulo I: Introducción
EL SECTOR DE LA CONSTRUCCIÓN RESIDENCIAL 9
RADIACIÓN SOLAR 22
ENERGÍA SOLAR FOTOVOLTAICA 26
ILUMINACIÓN 33
OBJETIVOS 60
METODOLOGÍA 61
Capítulo II: Marco Normativo
ARTICULO: THE USE OF SOLAR ENERGY IN THE BUILDINGS CONSTRUCTION SECTOR IN
SPAIN
Abstract 62
1 INTRODUCTION 63
2 SOLAR ENERGY IN SPAIN 64
3 LEGISLATION REGARDING CONSTRUCTION 67
3.1 Europe 67
3.2 Spain 67
4 METHODOLOGY 71
5 RESULTS 72
6 CONCLUSIONS 75
REFERENCES 77
Capítulo III: Modelos de Descomposición para la Irradiancia Horaria y la
Temperatura
ARTICULO: INTER-RELATIONSHIP BETWEEN MEAN-DAILY IRRADIATION AND
TEMPERATURE, AND DECOMPOSITION MODELS FOR HOURLY IRRADAITION AND
TEMPERATURE
Abstract 79
1 INTRODUCTION 80
2 PRESENTLY AVAILABLE INFORMATION 83
3 PREVIOUS WORK 84
4 PRESENTLY PROPOSED MODELS 94
4.1 Models for mean-daily irradiation 94
4.2 Models for mean-hourly irradiation 105
4.3 Models for hourly temperature 107
5 CONCLUSIONS 109
6 ACKNOWLEDGEMENTS 110
REFERENCES 110
Capítulo IV: Capacidad Energética Solar Fotovoltaica
ARTICULO: ANALYSIS OF THE PHOTOVOLTAIC SOLAR ENERGY CAPACITY OF
RESIDENTIAL ROOFTOPS IN ANDALUSIA (SPAIN)
Abstract 113
1 INTRODUCTION 114
2 CONTEXT AND JUSTIFICATION 115
3 METHODOLOGY 115
3.1 Building characterization. Total roof surface area 116
3.2 Useful roof surface area 119
3.3 Installation design 122
3.3.1 Installation type 1 123
3.3.2 Installation type 2 123
4 RESULTS 126
5 CONCLUSIONS 129
REFERENCES 129
Capítulo V: Modelo Energético
ARTICULO: DEVELOPMENT OF AN ENERGY MODEL FOR THE RESIDENTIAL SECTOR:
ELECTRICITY CONSUMPTION IN ANDALUSIA (SPAIN)
Abstract 131
1 INTRODUCTION 132
2 OUTLINE OF THE MODEL 133
3 CALCULATING ELECTRICAL POWER BY DETERMINATION OF THE
LUMINOUS FLUX 134
3.1 Units and systems of illumination 134
4 CHARACTERIZATION OF RESIDENTIAL HOUSING UNITS 135
5 NUMBER OF LUMINAIRES AND NOMINAL POWER 137
6 NATURAL LIGHT 138
7 HOUSEHOLD PROFILES 138
8 CALCULATION OF THE ELECTRICITY CONSUMPTION FOR LIGHTING 139
9 COMPARISON OF THE MODEL WITH QUESTIONNAIRE DATA 143
9.1 Questionnaire 143
10 CONCLUSIONS 145
11 ACKNOWLEDGEMENTS 146
REFERENCES 146
Capítulo VI: Conclusiones
CONCLUSIONES 149
CONCLUSIONS 150
Capítulo VII: Perspectivas de Trabajo Futuras 151
Anexo: Otras Publicaciones
ATICULO: EVALUATION OF THE ACCURACY OF MATHEMATICAL MODELS
THROUGH USE OF MULTIPLE METRICS 152
ANÁLISIS COMPARATIVO DE TRES MODELOS DE ESTIMACIÓN DEL CONSUMO
ENERGÉTICO DE LA VIVIENDA RESIDENCIAL 162
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 1
RESUMEN
La edificación en Europa, representa más del 40% del consumo final de energía de
los Estados miembros de la Unión Europea (UE), de los cuales el uso residencial
representa el 63% del consumo total de energía. En España el sector de la edificación
residencial consume el 10% (10.793 ktep.) del consumo de energía total.
El Plan de Fomento de las Energías Renovables en España proyecta superar en 2020
los objetivos marcados por Europa y cubrir con un 22,7% el consumo final de energía.
La Unión Europea ha establecido para los países miembros la obligación de elaborar un
Plan de Acción Nacional de Energías Renovables con el objetivo de ayudar al medio
ambiente.
El importante volumen de construcción de vivienda residencial en los últimos años y
el déficit en fuentes de energía convencionales, justifican las actuaciones que tengan
como objetivo conseguir la autososteniblidad energética de los usos relacionados con la
vivienda residencial (iluminación, calefacción, electrodomésticos,…). La solución de
instalar instalaciones fotovoltaicas integradas en los edificios puede ser una alternativa
interesante para conseguir dicha sostenibilidad energética.
En esta tesis se analiza el marco normativo a nivel de Europa y España, que rige el
proceso edificatorio en relación con el uso de la energía renovable. El objeto del estudio
es analizar la evolución en la implantación de distintas tecnologías relacionadas con la
energía en los edificios. Se hace especial hincapié en el uso de la energía solar. Se han
recopilado los datos estadísticos desde el año 1996 obtenidos de la Dirección General de
Programación Económica de la Secretaría de Estado de Infraestructuras dependiente del
Ministerio de Fomento. La investigación se centra en los edificios de nueva planta cuyo
uso principal es residencial. Se analiza la evolución que ha experimentado el número de
viviendas y edificios relacionándolos con el tipo de energía instalada (electricidad, gas
ciudad, GLP, energía solar, c. sólido).
Definidas las características de irradiación medias para cada una de las provincias de
Andalucía y los parámetros técnicos de la instalación fotovoltaica se estima la energía
eléctrica anual susceptible de ser generada. En esta tesis se presenta la evaluación de un
nuevo modelo para la determinación de la radiación solar media diaria y horaria
tendiendo como base la temperatura, obteniéndose los datos de radiación solar media
Abstract/Resumen
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 2
diaria y horaria y de temperatura que permiten diseñar una instalación solar
fotovoltaica.
Caracterizado el sector de la edificación se obtiene la capacidad energética de las
instalaciones fotovoltaicas conectadas a red que se podrían ubicar en las cubiertas de los
edificios. Partiendo de la caracterización del sector residencial y mapas urbanos
digitales obtenidos de Google Earth se mide la superficie útil de cubierta de una muestra
de edificios representativa de la población. Para ello se tienen en cuenta la altura de los
edificios, tipologías constructivas, además de las limitaciones tales como la orientación,
inclinación, la ubicación y el sombreado.
Determinada la energía eléctrica generada por las instalaciones fotovoltaicas se
estudia que porcentaje de energía eléctrica para uso lumínico podría ser cubierto por
esta energía generada. Con este objetivo se desarrolla un modelo que permite conocer la
evolución y comportamiento del consumo de energía eléctrica en el sector residencial
relacionado con el uso final de iluminación. Mediante análisis estadístico, se definen
tres tipologías de edificación representativas del parque de viviendas (las mismas que se
utilizaron para la obtención de la capacidad energética de las instalaciones fotovoltaicas
conectadas a red en las cubiertas de los edificios). Para cada una de estas tipologías se
calcula y diseña la instalación de iluminación necesaria para garantizar confort en las
actividades desarrolladas, obteniéndose el consumo energético.
Aplicando el modelo planteado, se compara el consumo eléctrico generado por el
uso exclusivo de bombillas incandescente con el que se obtendría sustituyendo las
bombillas convencionales por otras de bajo consumo. Los resultados obtenidos pueden
servir para apoyar las políticas energéticas nacionales e internacionales, como “La
Estrategia de Ahorro y Eficiencia Energética en España” y “La Estrategia Española de
Cambio Climático y Energía Limpia”.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 3
ABSTRACT
Building construction in Europe is responsible for more than 40% of the total energy
consumption of the member states of the European Union (EU). In these countries, 63%
of this total energy consumption is for residential uses. In Spain, the residential building
sector consumes 10% (10.793 ktep) of the total energy consumption in the country.
The national Plan de Fomento de las Energías Renovables [Plan for the
Development of Renewable Energies] predicts that in 2020, Spain will achieve the
objectives set by Europe and obtain 22.7% of its total energy from renewable energy
sources. The European Union requires all member states to elaborate a national action
plan to foment the use of renewable energies in order to preserve the environment.
In recent years, the huge volume of residential buildings and the growing deficit of
conventional energy sources justify actions whose purpose is to foment energy self-
sustainability for residential building uses (illumination, heating, use of electrical
appliances, etc.). The installation of photovoltaic installations in buildings is an
interesting alternative that will smooth the way towards energy sustainability.
This PhD dissertation analyzes the legal framework in Europe and Spain, which
regulates building construction and its use of renewable energies. The objective of the
study described in this dissertation was to analyze the evolution of the implementation
of various energy-related technologies in buildings with a special focus on solar energy.
Accordingly, from the year 1996 onwards, statistical data were obtained from the
Dirección General de Programación Económica de la Secretaría de Estado de
Infraestructuras [General Directorate of the Secretary of State for Infrastructure] which
depends on the Spanish Ministry of Development and Public Works. This dissertation
focuses on new buildings with a principally residential use. It analyzes the evolution
over the years of the number of houses and residential buildings, and relates this
information to the type of energy installed (electricity, natural gas, petroleum-based
liquid fuel, solar energy, and coal).
After defining the average irradiation characteristics of each province in the region
of Andalusia and the technical parameters of photovoltaic installation, the electrical
energy that can be potentially generated was estimated. This dissertation presents the
evaluation of a new model that determines the mean daily and hourly solar radiation,
based on temperature. The data regarding temperature as well as the mean daily and
Abstract/Resumen
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 4
hourly solar radiation provided by this model facilitates the design of photovoltaic solar
energy installations.
After describing the building construction sector, we obtained the energy capacity of
the grid-connected photovoltaic installations that can be placed on building roofs. Based
on the characterization of the residential sector and the digital urban maps obtained with
Google Earth, the useful roof surface of a representative sample of buildings was
measured and calculated. For this purpose, relevant factors considered were building
height, building type, and constraints such as orientation, tilt, location, and shade.
Once the electrical energy generated by photovoltaic installations was determined,
we then studied what percentage of electrical energy for lighting purposes could be
covered by solar energy. This led us to develop a model that provides a description of
the evolution and behaviour of electrical energy consumption in the residential sector,
specifically related to final illumination use. Statistical analysis was used to define three
building types that were representative of the total number of buildings (the same ones
used to obtain the energy capacity of the grid-connected photovoltaic installations on
building roofs). For each of these building types, we calculated and designed the
lighting installation necessary to guarantee the comfortable performance of daily
activities, and thus obtained the energy consumption.
The model was then used to compare the electricity consumption generated by the
exclusive use of incandescent light bulbs with the consumption that would be obtained
if they were replaced by low-energy light bulbs. The results obtained can be used to
support national and international energy policies such as La Estrategia de Ahorro y
Eficiencia Energética en España [Strategy for Energy Conservation and Efficiency in
Spain] and La Estrategia Española de Cambio Climático y Energía Limpia [Spanish
Strategy for Climate Change and Clean Energy].
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 5
ESTRUCTURA DE TESIS
El volumen de esta tesis doctoral incluye la investigación realizada como queda
reflejada en los artículos científicos publicados, enviados a revistas y congresos
internacionales. Cabe mencionar que los artículos aquí presentados son fieles a su
formato de publicación original en cuanto a nomenclatura de figuras, acrónimos y
referencias.
• El Capitulo I: Introducción, establece las bases conceptuales para el desarrollo
de la investigación. Incluye secciones sobre el sector de la construcción residencial,
radiación solar, energía solar fotovoltaica e iluminación, que se presentan de manera
general, refiriendo los artículos que conforman los sucesivos capítulos de tesis y donde
se explica detalladamente cada una de las metodologías utilizadas para cada objetivo
particular.
• El Capitulo II: Marco Normativo, Javier Ordóñez García, Eulalia Jadraque
Gago, Javier Alegre Bayo and Germán Martínez Montes “THE USE OF SOLAR
ENERGY IN THE BUILDINGS CONSTRUCTION SECTOR IN SPAIN”, recopila la
investigación realizada y publicada en la revista Renewable & Sustainable Energy
Reviews del año 2007, v.11, p. 2166-2178.
Tema que aborda y contribución
Se revisa el marco normativo que afecta a la edificación en relación con las energías
renovables a nivel de la Unión Europea y de España. Se analiza el sector de la
edificación y se obtiene la evolución que ha tenido la implantación de distintas
tecnologías relacionadas con la energía en los edificios haciendo especial hincapié al
estudio del uso de la energía solar.
En los últimos años se ha producido un desarrollo de las políticas que tienen como
objetivo la eficiencia energética y la potenciación de las fuentes renovables como
consecuencia de los compromisos adquiridos por los distintos países a nivel mundial, en
relación con los efectos nocivos del consumo de energías procedentes de combustibles
fósiles. También ha habido un incremento en la construcción de edificios
energéticamente sostenibles.
• El Capítulo III: Modelos de Descomposición para la Irradiancia Horaria y
la Temperatura, E J Gago, S Etxebarria, Y Tham, Y Aldali and T Muneer “INTER-
Estructura de tesis
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 6
RELATIONSHIP BETWEEN MEAN-DAILY IRRADIATION AND
TEMPERATURE, AND DECOMPOSITION MODELS FOR HOURLY
IRRADIATION AND TEMPERATURE”, recopila la investigación realizada y
publicada en la revista International Journal of Low-Carbon Technologies del año 2010
Advance Access published October 6.
Tema que aborda y contribución
Los registros de la temperatura terrestre han existido durante siglos y para muchas
ubicaciones del planeta. Tal es así que la temperatura es el parámetro meteorológico
más ampliamente medido.
No ocurre lo mismo con la medida de la radiación solar, que es registrada con muy
poca frecuencia quizás por considerarse un parámetro secundario o por el coste excesivo
que supone su medición.
Se presenta la evaluación de un nuevo modelo para la determinación de la radiación
solar media diaria y horaria sobre la base de la temperatura. El modelo propuesto es de
una constitución muy simple y no requiere ningún parámetro meteorológico secundario
como exigen los modelos que están disponibles en la literatura.
Se presentan también modelos de temperatura horaria que sólo requieren los datos
de temperatura media diaria.
La comparación se llevó a cabo teniendo en cuenta el rendimiento de los modelos
propuestos con modelos anteriores. Se encontró que los modelos actuales son capaces
de proporcionar estimaciones fiables de la irradiación y temperatura horaria con una
buena precisión.
• El Capítulo IV: Capacidad Energética Solar Fotovoltaica, J. Ordóñez, E.
Jadraque, J. Alegre and G. Martínez “ANALYSIS OF THE PHOTOVOLTAIC SOLAR
ENERGY CAPACITY OF RESIDENTIAL ROOFTOPS IN ANDALUSIA (SPAIN)”,
recopila la investigación realizada y publicada en la revista Renewable & Sustainable
Energy Reviews del año 2010, v.14, p. 2122-2130.
Tema que aborda y contribución
Se plantea como objetivo determinar el potencial energético solar de las cubiertas de
edificios residenciales en Andalucía, a partir de plantas fotovoltaicas conectadas a red y
ubicadas en las mismas. Para ello se desarrolla una metodología que permite a partir de
la caracterización de la vivienda, obtener la superficie susceptible de ser ocupada por el
sistema fotovoltaico, de esta forma se estima la energía eléctrica anual generada
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 7
teniendo en cuenta las características de irradiación media para cada una de las
provincias de Andalucía y los parámetros técnicos de la instalación fotovoltaica.
• El Capitulo V: Modelo Energético, E. Jadraque, A. Espín and J. Ordóñez
“DEVELOPMENT OF AN ENERGY MODEL FOR THE RESIDENTIAL SECTOR:
ELECTRICITY CONSUMPTION IN ANDALUSIA (SPAIN)”, recopila la
investigación realizada y publicada en la revista Energy and Building del año 2011, (In
Press).
Tema que aborda y contribución
El desarrollo de modelos que permitan conocer la evolución y comportamiento del
consumo de energía eléctrica en el sector residencial y su relación con los usos finales
hará posible la elaboración de medidas encaminadas a lograr un mayor ahorro
energético y al aumento de la eficiencia energética.
El objetivo es el diseño, desarrollo y aplicación de un modelo para la estimación del
consumo de energía eléctrica originado por el uso de la iluminación en el sector
residencial.
El modelo se aplica a Andalucía permitiendo obtener el ahorro en el consumo
eléctrico para uso de iluminación una vez se consigan los objetivos marcados por las
directrices políticas establecidas en la Estrategia Española de Cambio Climático y
Energía Limpia cuyo objetivo es la sustitución progresiva en una plazo de tres años de
las bombillas de filamento incandescente por otras de bajo consumo.
• El Capítulo VI: Conclusiones, sumariza los hallazgos más relevantes asociados
a la investigación que aquí se presenta como un compendio de los 4 capítulos anteriores
así como la investigación relevante asociada que se pone de manifiesto en el anexo.
• El Capítulo VII: Perspectivas de Trabajo Futuras, se plantean las futuras
líneas de investigación.
Además de los capítulos mencionados anteriormente se ha recogido en un anexo
contribuciones adicionales de la doctoranda en otras publicaciones relacionadas con los
objetivos de la investigación de esta tesis doctoral.
• En el Anexo, se hace referencia a otros trabajos de investigación en los que ha
participado la doctoranda asociado a la temática de esta tesis.
La primera publicación, Eulalia Jadraque Gago, Javier Ordóñez García, Germán
Martínez Montes y Javier Alegre Bayo “EDIFICACION SOSTENIBLE Y
EFICIENCIA ENERGETICA”, recopila la investigación realizada como comunicación
Estructura de tesis
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 8
presentada en el XII CONGRESO INTERNACIONAL DE INGENIERÍA DE
PROYECTOS y publicada en el libro de RESUMENES (ISBN: 978-84-613-3498-8).
Es ella se desarrolla un modelo de optimización del consumo energético en los
edificios residenciales con el fin de identificar potenciales ahorros y llevar a cabo
medidas de mejora que permitan mejorar la eficiencia en el consumo de energía en cada
edificio así como la identificación del potencial de incorporar energías alternativas.
La segunda publicación, N. Caliskan, E. Jadraque, Y. Tham and T. Muneer
“EVALUATION OF THE ACCURACY OF MATHEMATICAL MODELS
THROUGH USE OF MULTIPLE METRICS”, recopila la investigación realizada y
publicada en la revista Sustainable Cities and Society del año 2011, (In Press).
Se seleccionan una seria de indicadores que proporcionan una herramienta para la
validación de modelos matemáticos. Además se obtiene un factor que permite la
categorización de los modelos con respecto a sus resultados. Para ello se ha desarrollado
un software en Microsoft Excel /Visual Basic que permite la automatización de
validación del modelo.
Capítulo I: Introducción
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 9
EL SECTOR DE LA CONSTRUCCIÓN RESIDENCIAL
1 INTRODUCCIÓN
Los edificios residenciales en España son responsables del 10% del consumo total
de energía [1-2]. En el periodo comprendido entre los años 2002 y 2006 el parque de
viviendas creció un 90,35%, alcanzándose un total de 23.859.014 viviendas en el último
año [3]. Por otra parte, estas viviendas, en la gran mayoría, se han construido sin los
adecuados criterios de eficiencia energética.
Los hábitos de los consumidores hacen que se demande un grado de confort térmico
cada vez mayor, que provoca un aumento del consumo relacionado con la climatización
del edificio [4].
Por último, añadir que España tiene una fuerte dependencia energética del exterior,
la cual se cifra en 2007 en el 79,5% frente a un 53,1% en el total de la Unión Europea
[5].
Conscientes de la necesidad de reducir el consumo energético de los edificios, las
Administraciones Públicas han empezado a tomar medidas. A nivel estatal, la entrada en
vigor del Real Decreto 314/2006, de 17 de Marzo, por el que se aprueba el Código
Técnico de la Edificación y el Real Decreto 47/2007, de 19 de enero, por el que se
aprueba la Certificación Energética de Edificios tienen entre otros objetivos reducir el
consumo energético de los edificios.
En relación a los edificios existentes, el Ministerio de Industria, Turismo y
Comercio, en la 2ª Edición del Plan de Acción de Ahorro y Eficiencia Energética 2008-
2012, incluye medidas estratégicas dirigidas a mejorar sus características térmicas así
como ayudas económicas para las rehabilitaciones que conlleven una disminución del
consumo de energía del edificio.
2 ANTECEDENTES
El desarrollo de los métodos para estimar el consumo energético en la edificación ha
evolucionado desde metodologías sencillas [6], hasta el uso de algoritmos matemáticos
más complejos como las redes neuronales artificiales (RNA) [7], basados en la
Capítulo 1: Introducción. El sector de la construcción residencial
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 10
eficiencia de los procesos llevados a cabo por el cerebro e inspirados en su
funcionamiento.
Numerosos autores e investigadores han analizado los consumos en el sector de la
edificación mediante el estudio de los cambios en la estructura del consumo de energía
[8-10] o de las causas y efectos del mismo [11]. Proporcionan datos de apoyo para
trabajar con la eficiencia energética de los edificios [12], concluyendo que mientras que
el consumo de energía y los precios de la misma están aumentando, la disponibilidad de
energía está disminuyendo como consecuencia de que las medidas tomadas para hacer
frente a este problema han sido insuficientes para producir una mejora sustancial [11].
El consumo de energía también puede ser analizando cómo influye en éste el estilo
de vida de los ocupantes de un hogar. La dificultad de realizar estos estudios radica en
estandarizar los hábitos de consumo del usuario del sector residencial. Estos hábitos
dependen de factores como: el clima [13], situación económica [14], condición social,
cantidad y edades de habitantes por vivienda [15], características de la vivienda,
equipamiento eléctrico [16], aire acondicionado [17] y calefacción [18].
La calidad de la construcción [19,20] así como el diseño del edificio repercuten en
el consumo de energía de tal forma que se puede llegar a un aumento desmesurado del
consumo energético o a un ahorro sustancial de éste, partiendo de un mismo nivel de
confort, simplemente dejando que el propio edificio actúe como captador, acumulador y
distribuidor de la energía recibida y producida [21].
Para ello, el edificio deberá ofrecer a la orientación Norte los parámetros más
estancos y las áreas interiores de estancia limitada o que no utilicen calefacción. De la
misma manera, habrá que situar las mayores aberturas y las zonas sedentarias hacia el
Sur. Así, se podrán utilizar estos espacios como captadores por efecto invernadero. Esta
energía captada se distribuye y se acumula en el interior [22-25].
Como conclusión, es necesaria la supervisión de los Gobiernos para garantizar la
seguridad del abastecimiento energético, llevar a cabo acciones para promover la
sostenibilidad y el uso y competitividad del suministro de energía [26-28].
3 EL SECTOR DE LA CONSTRUCCIÓN
El ahorro y uso eficiente de la energía en la vivienda involucra la actividad de
arquitectos, ingenieros y profesionales del sector de la construcción. Abarca desde el
diseño mismo hasta el ofrecimiento a sus ocupantes de un confort ambiental integral y
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 11
el mejoramiento del ambiente y la calidad de vida. También involucra la actividad de
instituciones públicas, privadas y organismos no gubernamentales, vinculados a los
sectores constructivo, energético y ambiental, así como a estudiantes de arquitectura,
ingeniería y otras disciplinas afines, con el fin de identificar el impacto del cambio
ambiental global por el consumo energético en el diseño y construcción de las
viviendas.
Con el fin de ponderar en su justa medida el impacto, tanto energético como
ambiental, que ejerce el sector de la construcción, se citan unas cifras que demuestran la
importancia de este sector en comparación con el cómputo total.
En la Unión Europea el 40% del consumo total de energía corresponde a los
edificios [1].
En España el sector de la edificación residencial consume el 10% (10.793 ktep) del
consumo de energía total [3]. En el periodo comprendido entre los años 2002 y 2006 el
parque de viviendas creció un 90,35%, alcanzándose un total de 23.859.014 viviendas
en el último año [29]. Este incremento ha ido asociado a un aumento del consumo
eléctrico en el sector de la edificación [30]. A título de ejemplo, y para el caso de
Andalucía, la distribución del consumo de energía eléctrica en el año 2006 (35.342
GWh) fue la siguiente: sector residencial 34,9% (12.320 GWh), sector servicios 33,4%
(11.807 GWh), industria 26,5% (9.367 GWh), sector primario 4,1% (1.455 GWh) y
sector transporte 1% (393 GWh) [31].
La evolución en España del número de viviendas se muestra en gráfico 1.
0
100.000
200.000
300.000
400.000
500.000
600.000
700.000
800.000
2004 2005 2006 2007 2008 2009
Gráfico 1. Evolución del número de viviendas. Datos: Ministerio de Fomento. Elaboración propia.
Capítulo 1: Introducción. El sector de la construcción residencial
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 12
Andalucía tenía un parque total de 4.163.281 viviendas en 2006, el 17,5 % del total
de viviendas en España, es decir, en España una de cada cinco viviendas es andaluza.
Andalucía ocupaba en 2006 el primer lugar dentro de España en construcción de nuevas
viviendas, con un valor del 20,7% del total [32].
En el gráfico 2 se puede ver la evolución que ha experimentado la construcción de
edificios.
0
50.000
100.000
150.000
200.000
250.000
2004 2005 2006 2007 2008 2009
Gráfico 2. Evolución del número de edificios. Datos: Ministerio de Fomento. Elaboración propia.
Se puede concluir señalando la importancia que tiene el consumo de energía en los
edificios y que cualquier ahorro que se consiga en los mismos sería muy beneficioso,
tanto en el ámbito económico como medioambiental, justificándose los esfuerzos
encaminados a optimizar ese consumo.
Otro aspecto a considerar es el tipo de energía primaria que se está utilizando para
hacer frente a la demanda energética, ya que dependiendo del mismo el consumo será
más o menos perjudicial para el medio ambiente.
La gráfica 3 muestra el número de viviendas en edificios en España que son
suministrados por distintas formas de energía: eléctrica, gas ciudad, gases licuados de
petróleo y energía solar.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 13
0
100.000
200.000
300.000
400.000
500.000
600.000
700.000
800.000
2004 2005 2006 2007 2008 2009
Nº. Viviendas Electricidad Gas natural G.L.P E. Solar C. Líquido
Gráfico 3. Evolución del número de viviendas/energía instalada. Datos: Ministerio de Fomento.
Elaboración propia.
La Directiva SAVE1 de la Unión Europea dedica importantes fondos públicos para
financiar proyectos que reduzcan la emisión de CO2 a la atmósfera así como también
obliga a los países miembros a tomar medidas legales para reducir dichas emisiones
[28].
En lo referente exclusivamente a edificios, la Unión Europea ha aprobado la
Directiva 2010/31/UE del Parlamento Europeo y del Consejo de 19 de mayo de 2010
relativa a la eficiencia energética de los edificios. En ella se hace hincapié en la
necesidad de medidas que aumenten el número de edificios que no solo cumplan los
requisitos mínimos de eficiencia energética actualmente vigentes, sino que también
sean más eficientes energéticamente al reducir tanto el consumo energético como las
emisiones de dióxido de carbono [33].
El Código Técnico de la Edificación (CTE), al amparo de la Ley de la Ordenación
de la Edificación, define y desarrolla requisitos básicos de seguridad y habitabilidad que
deben satisfacerse en los edificios, prescribiendo las exigencias a cumplir al proyectar,
construir, usar, mantener y conservar los edificios, con el fin de fomentar su calidad,
garantizar la seguridad y salud de los usuarios y proteger el medio ambiente en su
entorno inmediato [33].
1 DIRECTIVA 93/76/CEE DEL CONSEJO de 13 de septiembre de 1993 relativa a la limitación de las
emisiones de dióxido de carbono mediante la mejora de la eficacia energética (SAVE).
Capítulo 1: Introducción. El sector de la construcción residencial
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 14
4 LA DEMANDA ENERGÉTICA DEL EDIFICIO
Llamamos demanda energética de un sistema (ya sea un edificio o cualquier otro
sistema) a la energía que necesita para realizar su función. Esta energía es suministrada
por un equipo que tiene un rendimiento determinado y, por tanto, necesitará más energía
que la estrictamente necesaria para suministrar la demanda. La energía consumida por el
equipo para suministrar la demanda se denominará consumo [35]. El consumo atiende
pues a la relación entre la demanda y el rendimiento del sistema suministrador de
energía siguiente [35]:
i
ii R
DC =
Nuestro objetivo es reducir el consumo de energía en los edificios, para ello
debemos disminuir la demanda y/o aumentar el rendimiento2. Para ver cuál de los dos
aspectos muestra mayor interés, se trazará una gráfica en donde se ilustra cómo afectan
al consumo las variaciones de ambas magnitudes (demanda y rendimiento).
Se supone un edificio que inicialmente tiene un consumo C0, una demanda D0 y un
sistema energético de rendimiento R0 (por tanto, C0 = D0/R0). Actuamos sobre el
edificio de tal manera que disminuimos su demanda en una cantidad d, y aumentamos el
rendimiento de los equipos en una cantidad r, por tanto su nuevo consumo será [35]:
rdC
rRdDC
′+′−
=+−
=11
00
0
donde d ′ = d / 0D y r ′ = r / 0R
2 Eficiencia energética del edificio: cantidad de energía calculada o medida que se necesita para satisfacer
la demanda de energía asociada a un uso normal del edificio que incluirá, la energía consumida en la
calefacción, la refrigeración, la ventilación, el calentamiento del agua y la iluminación. Directiva
2010/31/UE del Parlamento Europeo y del Consejo de 19 de mayo de 2010 relativa a la eficiencia
energética de los edificios.
∞≤′≤≤′≤
rd
010
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 15
En la gráfica 4 se representa la evolución de C / 0C (consumo) en función de las
nuevas variables d ′ y r ′ .
0
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
1
0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1
Consum
o
Incremento de la variable
C (r´=0)
C (d´=0)
Simultaneo
Gráfico 4. Evolución del consumo en función del aumento del rendimiento de los equipos o de la
disminución de la demanda del edificio. Fuente: Elaboración propia.
Puede concluirse que es mucho más eficiente disminuir la demanda del edificio que
aumentar el rendimiento de los equipos, si bien la optimización3 se consigue realizando
ambas acciones.
5 EL ORIGEN DE LA DEMANDA DEL EDIFICIO
En una vivienda la demanda energética es básicamente de tres tipos:
• Térmica, para satisfacer los requerimientos de ACS, calefacción y refrigeración.
• Lumínica, para los requerimientos de confort lumínico.
• Eléctrica, para las aplicaciones (diferentes aparatos).
El tipo de energía que se use para suplir estas demandas variará de un edificio a otro
(puede ser completamente eléctrica, solo en parte y la térmica sea suministrada por una
caldera de gas, gasóleo, etc.).
La demanda energética de un edificio varía ostensiblemente dependiendo de varios
factores entre los que destacan:
3 Optimización del consumo energético, cuyo objeto es disminuir el uso de energía pero produciendo los
mismos resultados finales. Directiva 2010/31/UE del Parlamento Europeo y del Consejo de 19 de mayo
de 2010 relativa a la eficiencia energética de los edificios.
Capítulo 1: Introducción. El sector de la construcción residencial
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 16
1. El clima. Es evidente que los gastos en calefacción, para dos edificios
idénticos aumentará en climas fríos. Por el contrario los gastos de refrigeración
serán superiores en climas cálidos [37].
2. La función. Un edificio de oficinas tendrá necesidades muy diferentes en
calidad y cantidad de energía que una vivienda, un hotel o un hospital. La demanda
variará así mismo de forma diferente a lo largo del día.
3. La calidad de la construcción. Dos edificios en un mismo clima presentan
consumos diferentes debido a la calidad tanto de los materiales como del acabado.
Un edificio con una carpintería de mala calidad presentará filtraciones muy elevadas
frente a otro con carpintería de mejor calidad [38].
4. El diseño del edificio. Las ganancias solares, que dependen de la orientación
de los huecos, la posibilidad de generar ventilaciones, etc., son conceptos de diseño
que nada tienen que ver con la calidad de la construcción y que, en cambio,
permiten ahorrar energía [39,40].
5. El uso o manipulación que los ocupantes hacen del mismo (desde la
manipulación manual hasta un sofisticado diseño de control automático) [18].
El gráfico 5 representa la explicación por usos del consumo anual residencial. Se
puede observar que el consumo se debe principalmente al uso del frigorífico, televisión,
iluminación y pequeños electrodomésticos. El consumo del frigorífico supone un 27,3%
de la demanda residencial, la iluminación el 23,5% y la televisión aporta el 12%. La
lavadora supone tan solo el 5% del consumo total residencial, pues su uso no es
continuo a lo largo del día. El consumo por calefacción eléctrica es del 10% de esta
demanda.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 17
0
5
10
15
20
25
30
88 89 90 91 92 93 94 95 96 97
Aire Acondicionado Calefacción Secadora Lavadora Lavavajillas Cocina
Iluminación Miscelánea Agua Caliente Congelador Frigorífico
TWh
Años
Estimación provisional
Gráfico 5. Explicación por usos del consumo anual residencial. Fuente: Proyecto INDEL. Atlas de la
Demanda Eléctrica Española. Programa de Investigación y Desarrollo Electrotécnico (PIE). Red Eléctrica
de España.
En el grafico 6, se aprecia que la curva de carga del sector residencial tiene su punta
de 21 a 22 horas, momento de mayor ocupación en el hogar. La lavadora y la secadora
concentran su consumo durante las mañanas. A las 12 horas, estos dos usos suponen el
21% de la demanda total residencial. Durante la noche existe otra punta de consumo de
lavadora y secadora consecuencia del trabajo fuera de casa de los componentes
principales de un número de hogares. El agua caliente tiene dos puntas claras, a las 9 de
la mañana y a las 5 de la tarde, que coinciden con el aseo matinal y el fregado de vajilla
posterior a la comida.
Los usos relacionados con la comida en el hogar, cocina y horno, concentran su
consumo en las horas previas a la comida, 2 de la tarde, y cena, en menor medida, a las
9 de la noche. El lavavajillas tiene sus puntas de consumo en las horas posteriores a la
comida y la cena, en torno a las 16 y 22 horas.
Iluminación, calefacción y televisión mantienen un perfil que coinciden con los
niveles de ocupación de los hogares. El frigorífico y congelador mantienen el mismo
nivel de consumo a lo largo del día, al no desconectarse en ningún momento.
Capítulo 1: Introducción. El sector de la construcción residencial
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 18
0
50
100
150
200
250
300
350
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Calefacción Secadora Lavadora Televisión Lavavajillas Cocina
Horno Iluminación Miscelánea Agua Caliente Congelador Frigorífico Gráfico 6. Curva de carga del hogar medio en un día tipo laborable. Fuente: Proyecto INDEL. Atlas
de la Demanda Eléctrica Española. Programa de Investigación y Desarrollo Electrotécnico (PIE). Red
Eléctrica de España.
REFERENCIAS
[1] IDAE, Estrategia de Ahorro y Eficiencia Energética en España 2004-2012. Plan
de acción 2008-2012. Ministerio de Industria, Turismo y Comercio, Instituto para la
Diversificación y Ahorro de la Energía, 2007.
[2] García JO, Gago EJ, Bayo JA, Montes GM. The use of solar energy in the
buildings construction sector in Spain. Renewable and Sustainable Energy Reviews
2007;11:2166–2178.
[3] Ministerio de Vivienda. Estimación del Parque de Viviendas. Secretaría General
Técnica. Subdirección General de Estudios y Estadísticas. www.mviv.es;2006.
[4] Consejería de Economía y Consumo. Guía de Rehabilitación Energética de
Edificios de Viviendas Dirección General de Industria, Energía y Minas;2008.
[5] Boletín Informativo del Instituto Nacional de Estadística. Industria y Energía.
7/2009.
[6] Fumo N, Mago P, Luck R. Methodology to estimate building energy
consumption using EnergyPlus Benchmark Models, Energy and Buildings
2010;42:2331–2337.
[7] Altan DO. The prediction of heating energy consumption in a model house by
using artificial neural networks in Denizli–Turkey. Advances in Engineering Software
2010;41:141–147.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 19
[8] Zhongren Z, Wenliang W, Xiaohua W, Qun C, Ou W. Analysis of changes in the
structure of rural household energy consumption in northern China: A case study.
Renewable and Sustainable Energy Reviews 2009;13:187–193.
[9] Shuqin C, Hiroshi Y, Mark DL, Zhenhai L. Contrastive analyses on annual
energy consumption characteristics and the influence mechanism between new and old
residential buildings in Shanghai, China, by the statistical methods. Energy and
Buildings 2009;41:1347–1359.
[10] Shuqin C, Hiroshi Y, Nianping L. Statistical analyses on summer energy
consumption characteristics of residential buildings in some cities of China. Energy and
Buildings 2010;42:136–146.
[11] Arun AE. Energy efficiency in New Zealand’s residential sector: A systemic
analysis. Energy Policy 2008;36:3278–3285.
[12] Shuqin C, Nianping L, Jun G, Yanqun X, Fengmei S, Ji N. A statistical method
to investigate national energy consumption in the residential building sector of China.
Energy and Buildings 2008;40:654–665.
[13] Aune M. Energy comes home. Energy Policy 2007;35:5457–5465.
[14] Dianshu F, Sovacool BK, Minh VK. The barriers to energy efficiency in China:
Assessing house hold electricity savings and consumer behavior in Liaoning Province.
Energy Policy 2010;38:1202–1209.
[15] Carlsson-Kanyama A, Lindén A. Energy efficiency in residences-Challenges
for women and men in the North. Energy Policy 2007;35:2163–2172.
[16] Adua L. To cool a sweltering earth: Does energy efficiency improvement off
set the climate impacts of life style? Energy Policy 2010;38:5719–5732.
[17] Chua KJ, Chou SK. Energy performance of residential buildings in Singapore.
Energy 2010;35:667–678.
[18] Desmedt J, Vekemans G, Maes D. Ensuring effectiveness of information to
influence household behavior. Journal of Cleaner Production 2009;17:455–462.
[19] Bansal NK, Bhattacharya A. Parametric equations for energy and load
estimations for buildings in India. Applied Thermal Engineering 2009;29:3710–3715.
[20] Bojic M, Despotovic M, Malesevic J, Sokovic D. Evaluation of the impact of
internal partitions on energy conservation for residential buildings in Serbia. Building
and Environment 2007;42:1644–1653.
Capítulo 1: Introducción. El sector de la construcción residencial
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 20
[21] Catalina T, Virgone J, BlancoE. Development and validation of regression
models to predict monthly heating demand for residential buildings. Energy and
Buildings 2008;40:1825–1832.
[22] Carvalho MMQ, La Rovere EL, Goncalves ACM. Analysis of variables that
influence electric energy consumption in commercial buildings in Brazil. Renewable
and Sustainable Energy Reviews 2010;14:3199–3205.
[23] Caldera M, Corgnati SP, Filippi M. Energy demand for space heating through a
statistical approach: application to residential buildings. Energy and Buildings
2008;40:1972–1983.
[24] Hammada F, Abu-Hijlehb B. The energy savings potential of using dynamic
external louvers in an office building. Energy and Buildings 2010;42:1888–1895.
[25] El Asmar T. REACt: self-sufficient renewable energy air-conditioning system
for Mediterranean countries. Desalination 2008;220:600–611.
[26] Rourke FO, Boyle F, Reynolds A. Renewable energy resources and
technologies applicable to Ireland. Renewable and Sustainable Energy Reviews
2009;13:1975–1984.
[27] Lv Shilei, WY. Target-oriented obstacle analysis by PESTEL modeling of
energy efficiency retrofit for existing residential buildings in China’s northern heating
region. Energy Policy 2009;37:2098–2101.
[28] Directiva 2010/31/UE del Parlamento Europeo y del Consejo de 19 de mayo de
2010, relativa a la eficiencia energética de los edificios.
[29] Ministerio de Vivienda, Encuesta sobre Tenencia y Uso de la Vivienda de los
Hogares para el año 2006. www.mviv.es;2006.
[30] Agencia Andaluza de la Energía, Datos energéticos de Andalucía 2006.
Consejería de Innovación, Ciencia y Empresa. Junta de Andalucía.
www.agenciaandaluzadelaenergia.es;2006.
[31] Ministerio de la Vivienda, Estadística de la Vivienda. www.mviv.es;2006.
[32] DIRECTIVA 93/76/CEE DEL CONSEJO de 13 de septiembre de 1993 relativa
a la limitación de las emisiones de dióxido de carbono mediante la mejora de la eficacia
energética (SAVE).
[33] Código Técnico de la Edificación. Documento Básico HE. Ahorro de Energía.
Abril 2009.
[34] Callen H. Thermodynamics and an Introduction to Thermostatistics, Wiley,
NY.;1985.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 21
[35] Montoro JM. Guía de buenas prácticas de eficiencia energética en edificación.
2004.
[36] Radhi H, Eltrapolsi A, Sharples S. Will energy regulations in the Gulf States
make buildings more comfortable–A scoping study of residential buildings. Applied
Energy 2009;86:2531–2539.
[37] Dixon G, Abdel-Salam T, Kauffmann P. Evaluation of the effectiveness of an
energy efficiency program for new home construction in eastern North Carolina. Energy
2010;35:1491–1496.
[38] Carlo J, Lamberts R. Development of envelope efficiency labels for
commercial buildings: Effect of different variables on electricity consumption. Energy
and Buildings 2008;40:2002–2008.
[39] Sozer H Improving energy efficiency through the design of the building
envelope. Building and Environment 2010;45:2581-2593.
[40] Tuhus-Dubrow D, Krarti M. Genetic-algorithm based approach to optimize
building envelope design for residential buildings. Building and Environment
2010;45:1574–1581.
Capítulo 1: Introducción. Radiación solar
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 22
RADIACIÓN SOLAR
1 INTRODUCCIÓN
Se define energía solar o radiación solar como la energía que proviene del sol. La
radiación solar que recibe la tierra es del orden de 1,5 kilovatios (kW) por hora. Esto
puede suponer un suministro de energía capaz de soportar el consumo mundial. Es
decir, se dispone de una fuente de energía con un enorme potencial y con la ventaja de
ser una energía renovable [1].
La energía solar presenta una serie de inconvenientes: captación, almacenaje, así
como el hecho de presentar variaciones debido a las condiciones meteorológicas,
ambientales y geográficas.
Como base de partida para desarrollar este trabajo será necesario conocer con
profundidad la física de la radiación solar al objeto de poder determinar la cantidad de
energía que puede ser aprovechada para su uso en el sector de la vivienda residencial
[2].
2 EL SOL
El sol es una inmensa fuente de energía inagotable con un diámetro de 1,39x109
metros (m) situado a una distancia media de 1,5x1011 respecto de la Tierra. Tiene una
temperatura media de 5.500ºC y en su interior tienen lugar una serie de reacciones que
producen una pérdida de masa que se transforma en energía. Esta energía liberada del
Sol se transmite al exterior mediante la radiación solar [3].
La radiación en el sol es 63.450.720 W/m2. La cantidad de energía por unidad de
tiempo y área que se alcanza sobre una superficie orientada normalmente hacia la
dirección de los rayos solares en la atmósfera es conocida como constante solar. Esta
constante tiene un valor medio anual de 1.367 W/m2 que varía estacionalmente en un
±3.3 debido a la excentricidad de la órbita terrestre [4].
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 23
3 RADIACIÓN SOLAR
En función de cómo inciden los rayos en la Tierra se distinguen tres componentes de
la radiación solar [4]:
• Directa: es la recibida del Sol sin desviarse a su paso por la atmósfera.
• Difusa: es la que sufre cambios en su dirección principalmente debidos a la
reflexión y difusión en la atmósfera.
• Albedo (reflejada): es la radiación directa y difusa que se recibe por reflexión en
el suelo u otras superficies próximas.
La radiación solar global es la suma de los tres tipos antes citados. Se define la
Irradiación como la energía por unidad de superficie a lo largo de un periodo de tiempo.
Se expresa en julios por metro cuadrado (J/m2), aunque también se expresa en Wh/m2
(potencia), mediante la conversión de unidades [1].
Figura 1. Componentes de la radiación solar terrestre total. Fuente: Elaboración propia.
4 IRRADIACIÓN SOLAR
La construcción de edificios energéticamente eficientes ha experimentado un
incremento en las tres últimas décadas. La utilización de elementos arquitectónicos de
captación de energía solar para maximizar el aprovechamiento de la luz del día, calor
solar, ventilación y energía solar requiere datos de la radiación solar por hora y la
temperatura.
Capítulo 1: Introducción. Radiación solar
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 24
En la mayoría de las regiones del mundo, especialmente en los países en desarrollo,
las mediciones de la radiación solar no son fáciles de conseguir debido al excesivo coste
y al gran esfuerzo que supone. La temperatura del aire, por el contrario, se mide en la
mayoría de estaciones meteorológicas. Hasta 2010 sólo había tres estaciones en el
noroeste de Europa con los registros de radiación en un periodo superior a 85 años. En
el Reino Unido no fue sino hasta la década de 1950 cuando la Oficina Meteorológica
instaló solarímetros Kipp. Por el contrario, existen registros de temperatura en
numerosos lugares del mundo y por un período mucho más largo. A título de ejemplo,
los registros más antiguos de la temperatura para el centro de Inglaterra han existido
desde 1659. En la India el número de lugares con registros de temperatura es de 161,
pero sólo existen 18 estaciones de medida de la irradiación. En Malasia y España
existen 41 y 113 estaciones que miden la temperatura, pero sólo hay 9 y 33 estaciones,
respectivamente, para el registro de la irradiación [2].
Thorton y Running [5] y Rivington y otros [6] señalan que incluso en los países más
desarrollados como los EE.UU. y Gran Bretaña, la superficie terrestre cubierta por
estaciones de medida de la radiación solar es menor al 1%.
La NASA proporciona un recurso útil para la obtención de valores mensuales de
irradiación y temperatura observados por satélite. Existe, sin embargo, la necesidad de
desglosar los datos diarios en horas, ya que hay una oscilación significativa de la
temperatura por hora en un día determinado.
La primera investigación relacionada con la radiación solar fue llevada a cabo por
Ångström y otros [7], estableciendo una relación entre la irradiación y la duración de la
insolación. Desde entonces la investigación en este campo ha recorrido un largo camino.
Hoy en día, una cantidad considerable de información está disponible en modelos
matemáticos que relacionan la radiación solar con otros parámetros meteorológicos
como la temperatura, la nubosidad, la cantidad de lluvia, la humedad e incluso la
visibilidad. Sin embargo, como se ha señalado anteriormente el parámetro que tiene la
mayor red de medición es la temperatura ambiente.
En este trabajo de investigación se presenta la evaluación de un nuevo modelo para
la determinación de radiación solar media diaria y horaria teniendo como base la
temperatura. El modelo propuesto es de una constitución muy simple y no requiere
ningún parámetro meteorológico secundario como exige otro grupo de modelos que
están disponibles en la literatura [2-8]. Por otra parte, los modelos de temperatura
horaria que se presentan sólo requieren los datos de temperatura media diaria.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 25
De este modo, se obtienen los datos de radiación solar media diaria y horaria y de
temperatura que permiten diseñar una instalación solar fotovoltaica.
REFERENCIAS
[1] Pareja AM. Radiación solar y su aprovechamiento energético. Nuevas Energías.
Marcombo Ediciones Técnicas. ISBN 978-84-267-1559-3;2009.
[2] Muneer T. Solar radiation and daylight models. Elsevier Butterworth-
Heinemann. ISBN 0-7506-5974-2;2004.
[3] Comellas GJ, Cruz M. El Sol y el Sistema Solar. Equipo Sirius, S.A. ISBN 978-
84-86639-00-6;1986.
[4] Méndez MJM, Cuervo GR. Energía Solar Fotovoltaica. ECA. Instituto de
Tecnología y Formación. FC editorial. ISBN 978-84-96743-29-8;2007.
[5] Thornton PE, Running SW. An improved algorithm for estimating incident daily
solar radiation from measurements of temperature, humidity, and precipitation. Agric
Meteorol 1999;93:211-228.
[6] Rivisgton M, Matthews K.B, Bunchan K. A comparison of methods for
providing solar radiation data to crop models and decision support systems. In:
Proceedings of the Integrated assessment and decision support, 1st Biennial Meeting of
International Environmental Modelling and Software Society, Vol. 3, June 24-27
2000:193-198.
[7] Angstrom A. Solar and terrestrial radiation. QJR. Meteorol Soc 1924;50:121-
125.
[8] Muneer T, Saluja G. A brief review of models for computing solar radiation on
inclined surfaces. Energy Conversion and Management 1985;25:443.
Capítulo 1: Introducción. Energía solar fotovoltaica
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 26
ENERGÍA SOLAR FOTOVOLTAICA
1 DEFINICIÓN
La energía solar fotovoltaica es aquella que se obtiene por medio del proceso directo
de transformación de la energía del sol en energía eléctrica. La transformación se realiza
por medio de módulos o paneles solares fotovoltaicos que captan la radiación solar. Los
paneles solares fotovoltaicos son elementos generadores de electricidad y están
formados por células fotovoltaicas [1].
2 CLASIFICACIÓN DE LOS SISTEMAS SOLARES FOTOVOLTAICOS
(SSF)
Se define sistema fotovoltaico el conjunto de componentes mecánicos, eléctricos y
electrónicos que concurren para captar y transformar la energía solar disponible,
transformándola en utilizable como energía eléctrica [2].
Las instalaciones fotovoltaicas, formadas por un conjunto de placas solares, pueden
ser de dos tipos [3]:
• Conectadas a la red: la energía es transformada en corriente alterna mediante los
inversores y vertida a la red eléctrica de distribución.
• Aisladas de la red: se utiliza para suministrar energía eléctrica a emplazamientos
aislados de la red. Están equipados con sistemas de acumulación de energía.
3 ELEMENTOS DE UN SISTEMA SOLAR FOTOVOLTAICO
En esta tesis se trabaja con un diseño de sistema fotovoltaico conectado a la red y
ubicado en la cubierta del edificio. Este sistema consta de los siguientes elementos
(Figura 1):
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 27
Generador FV Inversor
kWh
Consumode la
vivienda
kWh
Contadores
Red eléctrica
Figura 1. Esquema de sistema solar fotovoltaico conectado a Red. Fuente: Elaboración propia.
El elemento principal de un SSF es el generador fotovoltaico, que recibe el nombre
de célula solar. Esta capta la energía solar transformándola en corriente continua a
través del efecto fotovoltaico. La célula fotovoltaica es un elemento semiconductor en el
que, de forma artificial, se crea un campo eléctrico permanente de manera que cuando
se expone a la luz solar se produce un flujo de electrones que provoca la aparición de
dicha corriente [4].
Los tipos de paneles solares vienen dados por la tecnología de fabricación de las
células, y son fundamentalmente:
• Silicio cristalino (monocristalino y multicristalino).
• Silicio amorfo.
La célula fotovoltaica se comporta como un diodo: la parte expuesta a la radiación
solar es la N, y la parte situada en la zona de oscuridad, la P. Los terminales de
conexión de la célula se hallan sobre cada una de estas partes del diodo: la carga
correspondiente a la zona P se encuentra metalizada por completo, mientras que en la
zona N el metalizado tiene forma de peine, a fin de que la radiación solar llegue al
semiconductor (Figura 2).
Capítulo 1: Introducción. Energía solar fotovoltaica
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 28
Figura 2. Funcionamiento de una célula solar fotovoltaica. Fuente: Elaboración propia.
Los parámetros fundamentales de la célula solar fotovoltaica son los siguientes [4]:
• Corriente de iluminación (lL): la corriente generada cuando incide la radiación
solar sobre la célula.
• Corriente de oscuridad: es debida a la recombinación de los pares electrón-
hueco que se produce en el interior del semiconductor.
• Tensión de circuito abierto (Voc): la máxima tensión que se obtiene en los
extremos de la célula solar, que se da cuando no está conectada a ninguna carga. Es una
característica del material con el que está construida la célula.
• Corriente de cortocircuito (ISC): máximo valor de corriente que puede circular
por la célula solar. Se da cuando sus terminales están cortocircuitados.
Cuando la célula solar es conectada a una carga, los valores de tensión e intensidad
varían. Existen dos valores de tensión e intensidad para los cuales la potencia entregada
será máxima:
• Vm (tensión máxima).
• Im (intensidad mínima).
y que siempre serán menores que Voc e ISC.
En función de estos valores la potencia máxima que puede entregar la célula solar
será:
mmm IVP ⋅=
Esto nos permite definir el factor de forma (FF) como el cociente entre la máxima
potencia que puede entregar la célula a la carga y el producto de la tensión de circuito
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 29
abierto y la corriente de cortocircuito. En las células solares más habituales, los valores
típicos de FF son 0,7 ó 0,8.
OCOC
mm
IVIVFF⋅⋅
=
Al conjunto de células conectadas eléctricamente, encapsuladas y montadas sobre
una estructura de soporte o marco se le denomina panel solar o modulo fotovoltaico [5].
Las células fotovoltaicas producen corriente continua a una tensión nominal de 6,
12, 24… voltios. Estas células tienen un polo positivo y otro negativo pudiendo
conectarlas de dos formas:
• Conexión en paralelo: permitirá aumentar la intensidad total del conjunto.
• Conexión en serie: permitirá aumentar la tensión final en los extremos de la
célula equivalente.
Un elemento imprescindible en las instalaciones conectadas a redes es el inversor,
cuya función es convertir la corriente continua de la instalación en corriente alterna1.
Por tanto, el proceso de producción de electricidad en un sistema conectado a la red
eléctrica será:
• Captación de la radiación solar mediante las células.
• Producción de energía eléctrica en forma de corriente continua.
• Conversión en corriente alterna mediante inversores.
• Elevación de la tensión mediante un transformador de potencia.
• Venta a la red eléctrica.
4 DISEÑO Y CALCULO DE INSTALACIONES FOTOVOLTAICAS
CONECTADAS A RED
Las consideraciones que se deben tener en cuenta a la hora de realizar el diseño y
cálculo de una instalación solar fotovoltaica son:
1 La corriente continua (Direct Current-DC) es aquella cuyas cargas viajan siempre en la misma dirección
desde el punto de mayor potencial hasta el punto de menor potencial mientras que la corriente alterna
(Alternatin Current-AC) tiene una fuerza y dirección variable.
Capítulo 1: Introducción. Energía solar fotovoltaica
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 30
• Elección de la ubicación del lugar. La cantidad de radiación recibida dependerá
del lugar geográfico, es decir de la latitud. A la hora de orientar los paneles solares hay
que tener en cuenta que la posición de la Tierra con respecto del Sol presenta un ángulo
de declinación que no es constante y varía diariamente.
• Cantidad de energía que es capaz de inyectar a la red. Para estimar la energía
generada se utiliza la fórmula siguiente [6]:
CEM
mpdmp G
PRPGE
⋅⋅=
),( βα
donde:
Gdm (α,β). Valor medio mensual y anual de la irradiación diaria sobre el plano del
generador en kWh/(m2·día).
Pmp. Potencia pico del generador: franja horaria determinada en la que la energía
captada es recogida.
GCEM = 1 kWh/m2.
PR. Perfomance Ratio: factor de Rendimiento Global del sistema en el que se tienen
en cuenta las perdidas energéticas asociadas a los rendimientos de conversión de
corriente continua a alterna, de seguimiento del punto de máxima potencia del inversor
y al hecho de que el rendimiento de las células solares en la realidad es inferior al que
indica el valor de su potencia nominal, debido a que el valor de la temperatura de
operación suele ser notablemente superior a 25º [6].
• Estimación de la radiación recibida en el emplazamiento de la instalación. La
inclinación del panel influye en la cantidad de irradiación sobre la superficie. Por tanto
se deberá tener en cuenta el cálculo de las perdidas por radiación [6].
• Cálculo de la potencia del generador fotovoltaico [4]. Para determinar la
potencia pico que debe suministrar el generador fotovoltaico debemos conocer:
o La potencia que se quiere inyectar a la red eléctrica.
o El valor de la radiación solar.
o La estimación de las pérdidas que puedan existir en la instalación, obtenidas
según la siguiente expresión:
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 31
PRGGE
Pdm
CEMpmp ⋅
⋅=
),( βα
• Elección de los paneles solares para configurar el generador fotovoltaico [4].
Hay que considerar lo siguiente:
o Tensión necesaria para que el inversor proporcione energía correcta a la red.
o Potencia total que debe entregar el generador.
El numero de paneles necesarios lo obtenemos dividiendo la potencia pico entre el
valor de la potencia que es capaz de suministrar el panel.
panel
picopaneles Potencia
PotenciaN =
• Determinación del inversor. El inversor se encarga de convertir la corriente
continua de la instalación en corriente alterna, igual a la utilizada en la red eléctrica: 220
V de valor eficaz y una frecuencia de 50 Hz. Debe sincronizar la onda eléctrica
generada con la de la corriente eléctrica de la red.
Las características de un inversor deben ser:
o Alta eficiencia: debe funcionar bien para un amplio rango de potencias.
o Bajo consumo en vacío, es decir, cuando no hay cargas conectadas.
o Protección contra cortocircuitos.
o Seguridad.
o Buena regulación de la tensión y frecuencia de salida, compatible con la red
eléctrica.
REFERENCIAS
[1] Moro VM. Instalaciones Solares Fotovoltaicas (1ª edición). ISBN 978-84-973-
2776-3;2010.
[2] Fernández SJM. Guía completa de la Energía Solar Fotovoltaica.AMV
ediciones. ISBN 84-87440-45-2;2006.
Capítulo 1: Introducción. Energía solar fotovoltaica
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 32
[3] Castro GM, Carpio IJ, Guirado TR, Colmenar SA, Dávila GL. Energía Solar
Fotovoltaica. Monografías Técnicas de Energías Renovables. ISBN 84-86505-67-
4;2000.
[4] Díaz CT, Carmona RG. Instalaciones Solares Fotovoltaicas. Mc Graw hill. ISBN
978-84-481-7169-9;2010.
[5] Labouret A, Villoz M. Energía Solar Fotovoltaica. Manual Práctico.AMV
EDICIONES. 2008.
[6] Méndez MJM, Cuervo GR. Energía Solar Fotovoltaica. ECA. Instituto de
Tecnología y Formación. FC editorial. ISBN 978-84-96743-29-8;2007.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 33
ILUMINACIÓN
1 CONCEPTOS BÁSICOS
Una buena iluminación es importante para facilitar el rendimiento en una tarea
visual y crear un entorno visual adecuado.
Para conseguir una buena iluminación del recinto es necesario tener en cuenta una
serie de criterios básicos referentes a la disposición de la luz, condiciones del
alumbrado, superficie a iluminar, actividad a desarrollar, edad de los usuarios, etc.
La luz es una radiación electromagnética que se propaga por el espacio a una
velocidad c=300.000 km/s1. Según la Comisión Internacional de Iluminación (CIE), es
la radiación electromagnética capaz de estimular el órgano humano de la vista
provocando una sensación visual.
El espectro de radiaciones electromagnéticas es muy amplio. Para la iluminación
interesa la franja visible, teniendo cada longitud de onda y su frecuencia
correspondiente asociado un color [1]:
• Longitudes de onda “λ” comprendidas entre 380 nm (violeta) y 780 nm (rojo)
(1nm=1×10-9 m.).
• Frecuencias f= c/λ comprendidas entre 789×1012 Hz (violeta) y 384×1012 Hz
(rojo).
Tanto la luz natural como la artificial producida en las lámparas están formadas por
una agregación de radiaciones de distintas frecuencias. La luz natural es blanca al estar
formada por un conjunto continuo de radiaciones electromagnéticas de distinta
frecuencia, con un reparto entre frecuencias relativamente uniforme [1].
La luz artificial se produce en las lámparas normalmente de las siguientes formas
[2]:
• Por incandescencia.
1 James Clerk Maxwell (Edimburgo, 13 de junio de 1831- Cambridge, Reino Unido, 5 de noviembre de
1879). Físico británico conocido principalmente por haber desarrollado un conjunto de ecuaciones que
expresan las leyes básicas de la electricidad y magnetismo, así como por la estadística de Maxwell-
Boltzmann en la teoría cinética de gases.
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 34
Es la emisión de radiación luminosa mediante procesos térmicos. Consiste en
calentar un cuerpo sólido hasta su temperatura de incandescencia, emitiendo una luz de
un color dominante definido por dicha temperatura.
En iluminación se genera así la luz en las lámparas de incandescencia. El espectro
de la luz así producida (es decir, la distribución de energía entre las distintas
frecuencias) es bastante continuo, sin grandes irregularidades.
• Por luminiscencia.
Es la emisión de radiación luminosa por átomos, moléculas o iones, excitados por
choque de electrones, es decir, por procedimientos no térmicos. La luminiscencia es el
efecto luminoso producido generalmente por la excitación de los electrones de la última
capa. El espectro de la luminiscencia es discontinuo, lo que no ocurre con la
incandescencia, que es continuo. Se produce al añadir energía a un gas que se ioniza y
emite luz.
En iluminación se produce la luz así en las lámparas de luminiscencia, aportándose
energía por medio de una descarga eléctrica producida entre dos electrodos separados
por una atmósfera de gas.
2 MAGNITUDES Y UNIDADES DE MEDIDA
La luz es una radiación electromagnética y como tal se pueden estudiar las
magnitudes que definen esta forma de energía.
2.1 Flujo luminoso Φ (lumen-lm)
Es la cantidad de luz emitida en todas direcciones por una fuente de luz en la unidad
de tiempo. Se representa por la letra griega “fi”Φ, y se mide en lumen (lm) [3]2.
2.2 Rendimiento luminoso η (lumen/vatio-lm/W)
2Un lumen es la cantidad de luz monocromática de frecuencia 540x1012 hz. que tiene una potencia total de
1/683 W. Como se ve, es una unidad de “potencia luminosa”, es decir, cantidad de energía emitida por
unidad de tiempo.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 35
Es la relación entre el flujo luminoso emitido por una fuente de luz y la energía
eléctrica necesaria para producirla. Se representa por la letra griega “teta”η, y se mide
en lumen/vatio (lm/W) [4].
Viene dada por la siguiente relación:
WΦη =
donde,
Φ (lumen, lm): Flujo luminoso producido por la fuente luminosa.
W (vatios, W): Potencia eléctrica consumida por la fuente luminosa.
Conocida la potencia eléctrica de una lámpara “W” (W) y el rendimiento luminoso
“η”, podemos calcular el flujo luminoso que sale de la misma mediante la siguiente
fórmula:
WηΦ ×=
Tipo de lámpara Flujo luminoso (lm)
Rendimiento luminoso (lm/W)
Incandescente standard de 100 W 1.380 20 Fluorescente 40 W (Blanco frío) 3.200 95
Tabla 1. Flujo luminoso y rendimiento luminoso de algunas lámparas. Fuente: Obralux.
www.obralux.com.
2.3 Intensidad luminosa I (candela-cd)
Es la cantidad de luz emitida por una fuente de luz, en la unidad de tiempo, pero en
una única dirección. La intensidad luminosa emitida en una cierta dirección por una
fuente con flujo luminoso Φ en el sector de ángulo sólido3 ω centrado en esa dirección
es [4]:
3 Para comprender el concepto, debe tenerse en cuenta el concepto de “ángulo sólido” ω medido en
estereorradianes:
• Con ángulos planos, medidos en radianes, una circunferencia tiene 2·π radianes.
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 36
ωΦI =
Dicha intensidad luminosa se mide en candelas (cd).
2.4 Luminancia L (cd/m2=nit)
Es la intensidad luminosa por unidad de superficie aparente, procedente de una
fuente de luz [2]4.
2.5 Iluminancia ó nivel medio de iluminación requerido Em (lux-lx)
Se define como la cantidad de flujo luminoso incidente por unidad de superficie del
objeto iluminado. Se representa por la letra “E”, y se mide en lux, siendo 1 lux=1
lumen/1 m2 [2].
Viene dada por la expresión:
SΦE =
donde,
Φ (lumen, lm): flujo luminoso producido por la fuente luminosa.
S (m2): Superficie iluminada.
• Con ángulos sólidos, medidos en estereorradianes, una esfera tiene 4·π estereorradianes.
Así pues, una fuente luminosa que emita un flujo luminoso de 4·π lúmenes en todas direcciones, emite
una intensidad luminosa de 1 cd. en todas direcciones. Una candela es “la intensidad luminosa en una
dirección dada procedente de una fuente que emite una radiación monocromática de frecuencia
540x1.012 Hz. y cuya intensidad energética en dicha dirección es 1/683 W por estereorradián”. 4De este modo, la luminancia se mide en cd/m2 = nit, y viene dada por: siendo “I” la
intensidad luminosa de la fuente en cd. Permite medir la cantidad de luz que incide sobre un plano
inclinado un cierto ángulo “α” con la dirección del rayo de luz que viene de la fuente luminosa.
α cosSI
S´IL
⋅==
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 37
3 LÁMPARAS Y LUMINARIAS
3.1 Conceptos generales sobre lámparas
Generalmente se usan dos sistemas para medir las propiedades cromáticas de una
fuente luminosa. La temperatura de color (Tc) y el índice de rendimiento del color (Ra).
3.1.1 Temperatura de color (Tc)
Se define como la temperatura absoluta (K) a la que un cuerpo negro5 emite una
radiación luminosa que impresiona al ojo con un color igual o similar al de la fuente
luminosa. Se representa con “Tc” (K) [5].
En la tabla 2 se muestra la temperatura de color de diferentes fuentes luminosas,
definiéndose solamente las lámparas de uso doméstico más comunes:
Tipo de lámpara Temperatura de color (K)
Lámpara halógena 3.000 a 3.100 Lámpara de incandescencia 3.100 Lámpara de fluorescencia
• Luz día • Blanco neutro • Blanco cálido
5.000 4.000 3.300
Tabla 2. Temperaturas de color de distintos tipos de lámpara de uso doméstico. Fuente: Luminotécnia.
Obralux. www.obralux.com.
Se define apariencia de color como el color de la fuente luminosa. Es un color
fundamentalmente blanco con una cierta tonalidad de color y está asociada de forma
biunívoca a una temperatura de color [5].
Para cada temperatura de color de la tabla 2 y considerando el recinto que se va a
iluminar y la atmósfera luminosa buscada, se obtiene el grupo de apariencia de color de
la tabla 3:
5 El radiador denominado cuerpo negro es aquel cuyas propiedades de intensidad y espectro dependen
exclusivamente de su temperatura.
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 38
Grupo apariencia de color
Apariencia de color Temperatura de color Recintos adecuados
1, ww Cálido < 3.300 K Zonas residenciales 2, nw Neutro Entre 3.300 K y 5.000 K Zonas de trabajo
3, tw Frío > 5.000 K Altos niveles (lx), tareas especiales. Climas cálidos
Tabla 3. Clasificación según apariencias de color. Fuente: Norma Alemana DIN 5035.
3.1.2 Rendimiento de color (Ra ó IRC)
El rendimiento de color de una fuente de luz expresa la capacidad de discriminar
colores en los objetos iluminados por dicha fuente. Se representa con “Ra” ó con “IRC”
[5].
El IRC usual para los distintos tipos de lámparas se muestra en la tabla 4:
Tipo de lámpara IRC (%)
Incandescentes 100 Incandescentes con ciclo halógeno 100 Fluorescentes según tipos 15 a 95
Tabla 4. Rendimientos de color en las lámparas de uso doméstico. Fuente: Obralux. www.obralux.com.
3.2 Descripción de los tipos de lámparas más comunes para uso doméstico
3.2.1 Lámparas de incandescencia convencionales
Es la segunda lámpara eléctrica en antigüedad, después del arco voltaico (solo
usadas en focos y proyectores antiguos de cine)6.
Las bombillas modernas se realizan con un filamento de Wolframio arrollado en
espiral, que por el paso de la corriente se calienta hasta T = 2.400-2.900 K, dispuesto en
el interior de un globo de vidrio en el que se ha introducido un gas inerte (hidrógeno y
nitrógeno) [6].
Ventajas:
• Es muy adaptable y cómoda.
• Hay muchas formas:
6 Su invento se atribuye a Thomas Alva Edisón. Milán, Ohio, el 11 de febrero, 1847–18 de octubre, 1931,
que consiguió la primera lámpara de incandescencia o bombilla en 1879, usando un filamento
carbonizado de bambú, después de hacer más de mil ensayos con distintos materiales.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 39
o Mignon.
o Tubulares.
o Mariposa.
o Concentradoras (con reflector).
o Difusoras.
o Dicroica. Tiene un reflector de luz visible que permite pasar rayos infrarrojos
hacia atrás, disminuyendo el calor sobre el objeto iluminado.
• Se pueden fabricar para corriente continua (CC) y corriente alterna (CA), y para
cualquier tensión.
• Muy buena reproducción cromática, al tener espectro continuo, con IRC
prácticamente 100%.
• No necesitan accesorios para su funcionamiento, conectándose directamente a la
red.
• Fácil regulación de la intensidad luminosa con un potenciómetro.
• Posibilidad de encendido y reencendido instantáneos (posibilidad que no tienen
las lámparas de luminiscencia, obligando a usar éstas en algunos casos).
• Elevado flujo luminoso para una lámpara de reducidas dimensiones.
Inconvenientes:
• Bajo rendimiento luminoso (η= 8-18 lm/W). Solo el 10% de la energía
consumida por la lámpara se transforma en luz, el resto se disipa en forma de calor
(Figura 2).
• Corta vida útil (500-1.000 h.).
• Fuerte depreciación del flujo luminoso a lo largo de su vida útil.
• Es sensible a cambios de tensión en la red, disminuyendo de forma notable su
flujo luminoso y su vida útil.
Energía consumida
Pérdidas por calor
Luz visible
Figura 1. Rendimiento de una lámpara incandescente. Fuente: Elaboración propia.
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 40
3.2.2 Lámparas fluorescentes7
Están constituidas por un tubo de vidrio o bulbo tubular recubierto interiormente de
un material fluorescente, que tiene en sus extremos los electrodos y en su interior un
relleno de gas formado por gas inerte (argón o kriptón) y vapor de mercurio. En ellas se
produce una descarga eléctrica a través del gas entre los electrodos, iniciándose el arco
eléctrico. Dicho arco aumenta la temperatura y presión del mercurio contenido en forma
líquida dentro del tubo, provocando su vaporización y empezando éste a emitir luz.
Dicha luz incide sobre el material fluorescente que recubre el interior del tubo, el cual es
excitado sobre todo por la parte ultravioleta, emitiendo a su vez nueva luz que completa
el espectro emitido finalmente por la lámpara [7].
Las más comunes tienen la apariencia de un tubo de vidrio, de color blanco, con 2
conexiones eléctricas en sus extremos. Tradicionalmente presentan un diámetro de 38
mm. aunque, hoy lo más normal es 26 mm., del tipo ahorrador de energía. También los
hay de 16 mm., e incluso de diámetros inferiores para usos especiales. Tienen
longitudes de diversos valores normalizados y son normalmente de color blanco [8].
7 El más antiguo antecedente de la iluminación fluorescente posiblemente sea un dispositivo construido
por el físico alemán Heinrich Geissler en 1856, mediante el cual obtuvo una luz de brillo azulado a partir
de un gas noble (como argón o neón) encerrado en un tubo excitado con una bobina de inducción. Debido
a su forma, este dispositivo pasó a llamarse "Tubo de Geissler". En 1891, el inventor estadounidense
Daniel McFarlane Moore comenzó a realizar experimentos con tubos de descarga gaseosa, creando así en
1894 la Lámpara Moore, que era una lámpara comercial que competía con las bombillas de luz
incandescentes creadas por su antiguo jefe Thomas Alva Edisón. En 1901, Peter Cooper Hewitt presentó
su lámpara de vapor de mercurio, la cual emitía luz de coloración verde-azulada, que era inapropiada para
la mayoría de los usos prácticos. Sin embargo, su diseño fue muy cercano al de las lámparas actuales,
además de tener mayor eficiencia que sus similares incandescentes. En 1926, Edmund Germer, Friedrich
Meyer y Hans Spanner propusieron incrementar la presión del gas dentro del tubo y recubrirlo
internamente con un polvo fluorescente que convirtiera la radiación ultravioleta emitida por un gas en
estado de plasma en una luz blanca más uniforme. La idea fue patentada al año siguiente y posteriormente
la patente fue adquirida por la empresa estadounidense General Electric y bajo la dirección de George E.
Inman la hizo disponible para el uso comercial en 1938. Los conocidos tubos rectos y de encendido por
precalentamiento se mostraron por primera vez al público en la Feria Mundial de New York, en el año
1939. Desde entonces, los principios de funcionamiento se han mantenido inalterables, salvo las
tecnologías de manufactura y materias primas usadas, lo que ha redundado en la disminución de precios y
ha contribuido a popularizar estas lámparas en todo el mundo.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 41
La característica fundamental de estas lámparas es la composición de los polvos
fluorescentes que recubren el interior del tubo, pues de éstos depende la tonalidad de la
luz. Así se obtienen los siguientes tonos [7]:
• Color de luz blanco/día: Tc = 6.000-65.000 K (“tw” -triffle white). Aspecto
limpio y frío. Apropiado para locales de exposición con escaparates, tiendas de
automóviles, ordenadores, electrodomésticos…
• Color de luz blanco/neutro o blanco/frío: Tc = 4.000 K (“nw”- natural white).
Ambiente dinámico y de trabajo intelectual. Apropiado para aulas y locales
administrativos.
• Color de luz blanco/cálido: Tc = 3.000 K (“ww” - warm white). Atmósfera
acogedora, adecuada para lugares de recepción en hoteles, edificios sanitarios…
• Color de luz de lujo. Se consigue una luz de tonos agradables y cálidos, un mejor
IRC, pero menor rendimiento luminoso (η).
Para conseguir el funcionamiento se necesitan los siguientes elementos:
• Reactancia. Permite reducir el voltaje hasta el valor requerido.
• Cebador. Permite iniciar el arco en la luminaria.
• Condensador. Normalmente está integrado con la reactancia. Permite aumentar
el factor de potencia hasta el valor requerido (0,8 en los tubos de ∅ 26 mm.).
Ventajas [6]:
• Rendimiento luminoso elevado: η = 95-105 lm/W.
• Para un mismo flujo luminoso, su consumo es el 20% del de una lámpara de
incandescencia.
• Vida útil (6.000-20.000 h.), muy superior a la de las lámparas de incandescencia.
• Calentamiento muy débil. La superficie del tubo está a unos 55 ºC. Es así porque
invierte muy poca energía en calor. Supone menos carga para el aire acondicionado.
• Permite una amplia variedad de tonalidades de color, incluyendo la luz del día.
• La luz es difusa, lo que supone una gran comodidad visual, evitando en buena
medida los deslumbramientos y una menor cantidad de sombras.
Inconvenientes [6]:
• Precio más elevado de 1ª instalación que las lámparas incandescentes.
• Fragilidad mecánica.
• Tiempo de encendido apreciable. No son aptas para múltiples encendidos y
apagados, los cuales además disminuirían su vida útil.
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 42
• Originan en el usuario cierto “parpadeo” debido a la corriente alterna,
originando una fatiga mayor en el ojo, teniendo incluso cierto efecto estroboscópico.
Hoy se soluciona con las modernas reactancias y autotransformadores electrónicos, y
disponiendo los tubos por parejas o tríos en las luminarias.
• Al arrancar, consumen aproximadamente 1,8 veces la potencia nominal, que es
la que consumen en régimen permanente, lo cual debe ser tenido en cuenta a la hora de
dimensionar la instalación eléctrica.
Energía consumida100 %
Pérdidas por calor71,5 %
Luz visible28 %
Ultravioleta0,5 %
Figura 2. Rendimiento de una lámpara fluorescente. Fuente: Elaboración propia.
3.2.3 Lámparas de incandescencia halógenas o de cuarzo-yodo
Hay de 2 tipos [6]:
• De baja tensión: 230 V.
• De muy baja tensión: 50 V.
Su fundamento consiste en añadir unos gases con yodo al gas inerte que rellena el
globo de vidrio, con lo que se consigue regenerar en parte el filamento de Wolframio,
aumentando la vida útil de la lámpara.
Características:
• Flujo luminoso un 20% superior al de las lámparas incandescentes
convencionales (20-24 lm/W).
• Vida útil de ≈ 2000 h. Casi no tienen depreciación a lo largo de la misma.
• Necesitan para su funcionamiento una mayor temperatura, por ello, las lámparas
se hacen de menor tamaño.
• Permiten un control exacto del flujo luminoso, admitiendo el uso de reguladores
de dicho flujo.
• Conservan un IRC elevado.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 43
Se incluye a continuación un resumen de las características principales de las
lámparas más comunes de uso doméstico.
Formato o
modelo Potencia
(W) Tensión
(V) Rendimiento
(lm/W) Temperatura
color (K) IRC (%)
Standard
15 220/230 8 2.000 100 25 220/230 9 2.000 100 40 220/230 10 2.000 100 60 220/230 12 2.000 100 100 220/230 14 2.000 100 150 220/230 15 2.000 100 200 220/230 16 2.000 100 300 220/230 17 2.000 100 500 220/230 19 2.000 100 750 220/230 20 2.000 100
1.000 220/230 20 2.000 100 1.500 220/230 20 2.000 100 2.000 220/230 21 2.000 100
Standard mate 40 220/230 18 2.000 100 60 220/230 18 2.000 100 100 220/230 19 2.000 100
Tabla 5. Lámparas incandescentes. Fuente: Manual Práctico de Iluminación. Iluminación de Interiores.
Autor: Franco Martín Sánchez. 2005. ISBN: 84-87440-10-X.
Formato o
modelo Potencia
(W) Tensión
(V) Rendimiento
(lm/W) Temperatura
color (K) IRC (%)
Lineal (Doble terminal)
100 220/230 17 3.000 100 150 220/230 18 3.000 100 200 220/230 18 3.000 100 250 220/230 20 3.000 100 300 220/230 20 3.000 100 400 220/230 20 3.000 100 500 220/230 20 3.000 100 750 220/230 23 3.000 100
1.000 220/230 24 3.000 100 1.500 220/230 24 3.000 100 2.000 220/230 24 3.000 100
Cápsulas de baja tensión
35 12 18 3.000 100 50 12 20 3.000 100 75 12 21 3.000 100 100 12 24 3.000 100
Standard mate
20 12 - 3.200 100 35 12 - 3.200 100 50 12 - 3.200 100 65 12 - 3.200 100
Tabla 6. Lámparas halógenas. Fuente: Manual Práctico de Iluminación. Iluminación de Interiores.
Autor: Franco Martín Sánchez. 2005. ISBN: 84-87440-10-X.
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 44
Formato o modelo
Potencia (W)
Tensión (V)
Rendimiento (lm/W)
Temperatura color (K) IRC (%)
Cápsulas tensión normal
75 220/230 14 2.800 100 100 220/230 14 2.800 100 150 220/230 15 2.800 100
Doble envoltura
75 220/230 15 2.900 100 100 220/230 16 2.900 100 150 220/230 17 2.900 100 500 220/230 21 3.200 100
1.000 220/230 24 3.200 100 2.000 220/230 25 3.200 100
Globo 100 220/230 15 2.800 100 150 220/230 14 2.800 100
Par-38 75 220/230 - 2.900 100 100 220/230 - 2.900 100 150 220/230 - 2.900 100
Tabla 7. Lámparas halógenas. Fuente: Manual Práctico de Iluminación. Iluminación de Interiores. Autor:
Franco Martín Sánchez. 2005. ISBN: 84-87440-10-X.
Formato o
modelo Potencia
(W) Tensión (V) Rendimiento (lm/W)
Temperatura color (K) IRC (%)
Tubo standard diámetro 38
mm.
20 Luz Día 53 6.500 75 40 Luz Día 63 6.500 75 65 Luz Día 62 6.500 75 115 Luz Blanca 60 4.100 63 65 Luz Blanca 73 4.100 63 40 Luz Blanca 72 4.100 63 20 Luz Blanca 60 4.100 63
Tubo standard diámetro 26
mm.
15 Luz Día 56 6.200 72 18 Luz Día 59 6.200 72 23 Luz Día 70 6.200 72 30 Luz Día 67 6.200 72 36 Luz Día 70 6.200 72 58 Luz Día 69 6.200 72 15 Luz Blanca 64 4.100 63 18 Luz Blanca 64 4.100 63 23 Luz Blanca 83 4.100 63 30 Luz Blanca 77 4.100 63 36 Luz Blanca 83 4.100 63 58 Luz Blanca 83 4.100 63
Tabla 8. Lámparas fluorescentes. Fuente: Manual Práctico de Iluminación. Iluminación de Interiores.
Autor: Franco Martín Sánchez. 2005. ISBN: 84-87440-10-X.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 45
Formato o modelo
Potencia (W) Tensión (V) Rendimiento
(lm/W) Temperatura
Color (K) IRC (%)
Tubo standard diámetro 26
mm.
18 Blanco Cálido 81 3.000 85 30 Blanco Cálido 77 3.000 85 36 Blanco Cálido 96 3.000 85 58 Blanco Cálido 93 3.000 85 18 Blanco Cálido 53 3.000 95 30 Blanco Cálido 60 3.000 95 36 Blanco Cálido 64 3.000 95 58 Blanco Cálido 62 3.000 95
Tubo standard diámetro 16
mm.
14 Luz Día 79 6.200 86 21 Luz Día 84 6.200 86 24 Luz Día 67 6.200 86 28 Luz Día 86 6.200 86 35 Luz Día 87 6.200 86 39 Luz Día 73 6.200 86 49 Luz Día 74 6.200 86 54 Luz Día 75 6.200 86 80 Luz Día 72 6.200 86
Tabla 9. Lámparas fluorescentes. Fuente: Manual Práctico de Iluminación. Iluminación de Interiores.
Autor: Franco Martín Sánchez. 2005. ISBN: 84-87440-10-X.
3.3 Definición y clasificación de las luminarias
Luminarias son aquellos aparatos que distribuyen, filtran o transforman la luz
emitida por una o varias lámparas y que contiene todos los accesorios necesarios para
fijar las lámparas y conectarlas al circuito eléctrico de alimentación [9].
Las luminarias para alumbrado interior incluyen los siguientes elementos [10]:
• Lámparas de incandescencia.
• Luminarias de tubos fluorescentes.
• Luminarias de lámparas de descarga.
Las luminarias pueden dirigir la luz mediante alguno o varios de los elementos
siguientes [9]:
• Elementos reflectores. Situados tras la lámpara, normalmente con acabado de
espejo o de color blanco.
• Elementos refractores. Situados delante de la lámpara, son transparentes o
translúcidos, y la luz pasa a través de ellos modificando su dirección, actuando el
elemento como una lente.
• Elementos difusores. Situados delante de la lámpara. Son translúcidos, y la luz
cuando pasa a través de ellos se difunde en todas direcciones, cambiando en algunos
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 46
casos su color y evitando que se vea directamente la lámpara, con lo que se disminuyen
o evitan los deslumbramientos.
Las luminarias se pueden clasificar atendiendo a los criterios siguientes [11]:
• Según la forma de transmitir la luz:
o Luminarias reflectoras.
o Luminarias refractoras.
o Luminarias difusoras. Difunden la luz para conseguir una luz difusa y
disminuir el deslumbramiento que originaría la visión directa de la lámpara. Se
emplean mucho en iluminación de viviendas.
o Luminarias mixtas.
• Según la simetría del haz luminoso.
o Luminarias de distribución simétrica. En ellas el flujo luminoso se reparte
simétricamente con respecto a dos planos verticales perpendiculares alineados con
los ejes principales de la luminaria. Son así la práctica totalidad de las luminarias
usadas en iluminación de interiores.
o Luminarias de distribución asimétrica.
• Según la distribución del flujo luminoso con respecto al plano horizontal.
o Luminarias de flujo directo. Cuando el flujo luminoso emitido bajo el plano
horizontal que pasa por el vértice de la fuente de luz es ≥90% del flujo luminoso útil.
o Luminarias de flujo semidirecto. Entre el 60% y el 90%.
o Luminarias de flujo difuso y directo-indirecto. Entre el 40% y el 60%.
o Luminarias de flujo semiindirecto. Entre el 10% y el 40%.
o Luminarias de flujo indirecto. Entre el 0% y el 10%.
• Según el ángulo de apertura.
o Luminarias de tipo intensivo. β entre 0º y 30º.
o Luminarias de tipo intensivo. β entre 0º y 30º.
o Luminarias de tipo semiintensivo. β entre 30º y 40º.
o Luminarias de tipo dispersor. β entre 40º y 50º.
o Luminarias de tipo semiextensivo. β entre 50º y 60º.
o Luminarias de tipo extensivo. β entre 60º y 70º.
o Luminarias de tipo hiperextensivo. β entre 70º y 90º.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 47
4 METODO RESUMIDO
4.1 Iluminación de interiores
4.1.1 Lámparas y luminarias
Las lámparas empleadas en iluminación de interiores abarcan casi todos los tipos
existentes en el mercado (incandescentes, halógenas, fluorescentes, etc.). Las lámparas
escogidas, por lo tanto, serán aquellas cuyas características (fotométricas, cromáticas,
consumo energético, economía de instalación y mantenimiento, etc.) mejor se adapten a
las necesidades y características de cada instalación (nivel de iluminación, dimensiones
del local, ámbito de uso, potencia de la instalación...) [12].
Fluorescentes compactas
Ámbito de uso Tipos de lámparas más utilizados
Doméstico
Incandescente Fluorescente Halógenas de baja potencia Fluorescentes compactas
Oficinas Alumbrado general: fluorescentes Alumbrado localizado: incandescentes y halógenas de baja tensión
Comercial (Depende de las dimensiones y características del comercio)
Incandescentes Fluorescentes Grandes superficies con techos altos: mercurio a alta presión y halogenuros metálicos
Industrial Industrial
Deportivo
Luminarias situadas a baja altura: fluorescentes Luminarias situadas a gran altura: lámparas de vapor de mercurio a alta presión, halogenuros metálicos y vapor de sodio a alta presión
Tabla 10. Tipos de lámparas más utilizados en función del ámbito de uso. Fuente: D. Oriol Boix
Aragonés. Departamento de Ingeniería Eléctrica de UPC. Septiembre de 1999. ISBN: 84-600-9647-5.
http://edison.upc.edu//curs.ilum.
La elección de las luminarias está condicionada por la lámpara utilizada y el entorno
de trabajo de ésta. La forma y tipo de las luminarias oscilará entre las más funcionales,
donde lo más importante es dirigir el haz de luz de forma eficiente como pasa en el
alumbrado industrial, a las más formales donde lo que prima es la función decorativa
como ocurre en el alumbrado doméstico [12].
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 48
Las luminarias para lámparas incandescentes tienen su ámbito de aplicación básico
en la iluminación doméstica. Por lo tanto, predomina la estética sobre la eficiencia
luminosa. Solo en aplicaciones comerciales o en luminarias para iluminación
suplementaria se buscará un compromiso entre ambas funciones. Son aparatos que
necesitan apantallamiento pues el filamento de estas lámparas tiene una luminancia muy
elevada y pueden producir deslumbramientos [11].
En segundo lugar tenemos las luminarias para lámparas fluorescentes. Se utilizan
mucho en oficinas, comercios, centros educativos, almacenes, industrias con techos
bajos, etc. por su economía y eficiencia luminosa. Así pues, nos encontramos con una
gran variedad de modelos que van de los más simples a los más sofisticados con
sistemas de orientación de la luz y apantallamiento (modelos con rejillas cuadradas o
transversales y modelos con difusores) [11].
4.1.2 Sistemas de alumbrado interior
Cuando una lámpara se enciende el flujo emitido puede llegar a los objetos de la
sala directamente o indirectamente por reflexión en paredes y techo. La cantidad de luz
que llega directa o indirectamente determina los diferentes sistemas de iluminación con
sus ventajas e inconvenientes [13].
Luz directa.
Luz indirecta proveniente del techo.
Luz indirecta proveniente de las paredes.
Figura 5. Sistemas de Iluminación. Fuente: Luminotecnia. Iluminación de Interiores y exteriores. D.
Oriol Boix Aragonés. Departamento de Ingeniería Eléctrica de UPC. Septiembre de 1999. ISBN: 84-600-
9647-5. http://edison.upc.edu//curs.ilum.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 49
Según la distribución del flujo luminoso con respecto al plano horizontal se pueden
distinguir los siguientes tipos de iluminación, definidos por el tipo de luminaria [14]:
• Iluminación directa. Del 90% al 100% del flujo luminoso se dirige hacia el
suelo. Las luminarias son normalmente reflectoras, con el reflector dirigido hacia abajo.
Rendimiento luminoso del sistema: 45%-50% (es decir, un 45%-50% de la luz
producida en las lámparas llega al plano de trabajo).
• Iluminación semidirecta. Del 60% al 90% del flujo luminoso se dirige hacia el
suelo. Las luminarias de este tipo se consiguen añadiendo a las luminarias de
iluminación directa un difusor adecuado que conduce parte de la luz por encima de la
horizontal, reduciendo algo el rendimiento luminoso de la luminaria, pero consiguiendo
un efecto mucho mejor. Rendimiento luminoso del sistema: 40%.
• Iluminación difusa y directa-indirecta (también llamada mixta). Se dirige al
suelo aproximadamente la misma cantidad que al techo (40% al 60%). Rendimiento
luminoso del sistema: 35%. Distinguimos 2 casos:
o Iluminación difusa. Se emite luz difusa en todas direcciones, rodeando la
lámpara en la luminaria con un elemento difusor que suele ser globo de material
traslúcido.
o Iluminación directa-indirecta. Se emite luz hacia arriba y hacia abajo, también
con un elemento difusor, pero no en el plano horizontal, ya que la luminaria en esa
zona es opaca.
• Iluminación semiindirecta. Del 10% a 30% del flujo luminoso se dirige hacia el
suelo, y del 60% al 90% hacia el techo. Se consigue dirigir así el flujo luminoso
disponiendo en la parte inferior de la luminaria un difusor realizado con pantalla de
papel, plásticos o vidrios traslúcidos, que permiten un control muy preciso de la luz que
pasa a través de ellas. El rendimiento luminoso del sistema es de un 25%, ya que buena
parte de la luz es absorbida por techo y paredes.
• Iluminación indirecta. Casi todo el flujo luminoso (90%) se dirige hacia arriba
en ángulos por encima de la horizontal, repartiéndose uniformemente en el techo y
reflejándose desde éste hacia el suelo.
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 50
4.2 Deslumbramiento
Cuanto mayor es la cantidad de luz sobre una tarea o plano de trabajo, parece
razonable que habrá un mayor rendimiento visual, pero un exceso de iluminación puede
producir efectos perjudiciales, como puede ser el deslumbramiento8 y la contaminación
lumínica9. Por tanto, se ha de considerar que obtener el nivel de iluminación adecuado a
la tarea y al entorno debe ser tarea prioritaria del diseño de un sistema de alumbrado,
aparte de otras consideraciones estéticas, económicas, de mantenimiento, etc. [2].
4.3 Niveles de iluminación recomendados
Los niveles de iluminación recomendados para un local dependen de las actividades
que se vayan a realizar en él. A continuación se reflejan en la tabla 11 los valores
mínimos y recomendados de la iluminancia.
8 Es la sensación producida por el exceso de iluminación dentro del campo visual. Esta sensación altera la
tarea visual del ojo produciéndole anomalías: molestias, reducción de visibilidad o ambas a la vez. En la
iluminación interior, el deslumbramiento fisiológico (o perturbador) es de menos importancia que el
deslumbramiento psicológico (molesto). El deslumbramiento, en cualquiera de los tipos anteriores, viene
producido directamente o por reflexión. El deslumbramiento se puede controlar actuando sobre las
lámparas, luminarias y materiales que rodean el espacio donde se realiza la tarea visual. 9 La contaminación lumínica o resplandor luminoso nocturno en el cielo es el brillo producido por la
reflexión y difusión de la luz artificial en los gases y partículas en suspensión de la atmósfera.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 51
ESTANCIA ILUMINANCIA Mínima (lx)
ILUMINANCIA Recomendada
(lx) EDIFICIOS DE VIVIENDAS
Vestíbulo 100 150 Pasillo 100 150 Escalera interior 150 200 Cocina 300 400 Cuarto de baño 100 300 Aseo 100 200 Dormitorios 50 100 Vestidor 150 200 Comedor 200 300 Salón-Estar 200 300 Cuarto de los niños 100 200 Biblioteca 500 600 Cuartos de estudio 300 500 Despacho 400 500 Trastero 50 100 Garaje privado 100 200
ZONAS COMUNES Portal 100 200 Escalera 100 150 Pasillos 100 150 Porches 50 100 Portería-Conserjería 100 150 Patios 50 50 Cuartos de basura 150 200
LOCALES TECNICOS Cuarto de contadores de agua 200 250 Cuarto de contadores de gas 200 250 Cuarto de contadores eléctricos 200 250 Centros de transformación 250 250 Sala de maquinas de ascensor 200 300 Sala de maquinas de frió 200 250 Sala de calderas 200 250 Sala de grupo de elevación de agua 200 250 Sala de grupo contra incendio 200 250 Sala de grupo de emergencia 200 250
Tabla 11. Valores de iluminación. Fuente: Manual de Alumbrado Westinghose. Editorial Dossat,
S.A. Madrid 1989
4.4 Cálculo de instalaciones de alumbrado
4.4.1 Método de los lúmenes o del factor de utilización
En el interior de un local la iluminación en un punto sobre una superficie horizontal
se obtiene no sólo por el flujo recibido directamente desde la luminaria, sino también
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 52
por el reflejado desde el techo y las paredes laterales que reciben flujo luminoso de la
luminaria. Parte de este flujo es reflejado según la naturaleza de la superficie y las
características espectrales del flujo incidente. Después de una o más reflexiones, una
parte de dicho flujo puede recibirse eventualmente en la superficie horizontal
considerada que es denominada generalmente como plano de trabajo y puede ser un
plano real o un plano imaginario a una distancia determinada sobre el suelo [13].
Si el flujo que incide sobre el plano de trabajo se divide por el flujo emitido por el
elemento de iluminación, la relación es denominada factor de utilización para la unidad
determinada y la sala particular considerada [15].
Para el cálculo del factor de utilización además de tener en cuenta lo anterior, es
necesario considerar los siguientes parámetros:
• Distancia de suspensión de la luminaria. Altura del plano de trabajo al suelo.
Altura del plano de las luminarias al plano de trabajo h (m). La iluminación pretende
conseguir una óptima iluminación del plano de trabajo, situado a la siguiente altura “h1”
del suelo [16]:
o Locales de trabajo y estancia: h1 = 0,85 m.
o Pasillos y zonas de paso: h1 = 0,00 m.
Si la altura y la estética lo permiten, la distancia de suspensión (d´) de las luminarias
debería estar entre los siguientes valores [15]:
o Iluminación directa, semidirecta y difusa
5d
3d
d yentre=′
o Iluminación semiindirecta e indirecta
4d
d =′
donde:
d: altura del plano de trabajo al techo.
d': altura entre el plano de las luminarias y el techo.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 53
• Elección de la apertura del haz y del modelo de luminaria. La apertura o
dispersión del haz de luz se define como el ángulo comprendido entre las dos
direcciones en que la intensidad luminosa cae un determinado porcentaje (usualmente
el 10% ó el 50%) del valor máximo que hay en el centro del haz donde la intensidad es
máxima [15]. La apertura del haz de la luminaria se elegirá en función de la altura del
local “H”, de acuerdo con la siguiente tabla:
Tipo de luminaria Altura del local H (m)
Distancia máxima entre luminarias
Intensiva >10 e ≤1,2h Semiintensivo 6– 10 e ≤1,5h Semiextensiva 4–6 Extensiva ≤4 e ≤1,6h
Distancia pared–luminaria: e/2
Tabla 12. Distancia máxima entre luminarias. Fuente: Luminotecnia. Iluminación de Interiores y
exteriores. D. Oriol Boix Aragonés. Departamento de Ingeniería Eléctrica de UPC. Septiembre de 1999.
ISBN: 84-600-9647-5. http://edison.upc.edu//curs.ilum.
• Índice del local (K). El índice del local (K) es el índice que valora la influencia
de las dimensiones del local sobre el rendimiento de las luminarias [12]:
Sistema de iluminación Índice del local
Iluminación directa, semidirecta, directa-indirecta y
general difusa
Iluminación indirecta y semiindirecta
Tabla 13. Índice del local dependiendo del sistema de iluminación. Fuente: Luminotecnia.
Iluminación de Interiores y exteriores. D. Oriol Boix Aragonés. Departamento de Ingeniería Eléctrica de
UPC. Septiembre de 1999. ISBN: 84-600-9647-5. http://edison.upc.edu//curs.ilum.
donde:
a: Largo de la superficie rectangular del local (m).
b: Ancho de la superficie rectangular del local (m).
h: Distancia entre el plano de trabajo (0,85 m. sobre el suelo) y el plano horizontal
de las luminarias emplazadas colgadas del techo, adosadas a este o empotradas en el
mismo.
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 54
• Factor de reflexión o reflectancia “ρ” de paredes, suelo y techo. Es la relación
entre el número de lúmenes reflejados (flujo luminoso reflejado) por superficie y el
número de lúmenes recibidos en esa misma superficie (flujo luminoso incidente) [12].
Podemos utilizar los valores de la tabla 14 para determinar la reflectancia de los
distintos revestimientos. Como las paredes suelen estar cubiertas con muebles, cuadros,
ventanas, etc., no debería tomarse un ρparedes>0,60 aun con paredes blancas [15].
Paramento Color Factor de reflexión (ρ)
Techo Blanco o muy claro 0,7
Claro 0,5 Medio 0,3
Paredes Claro 0,5 Medio 0,3 Oscuro 0,1
Suelo Claro 0,3 Oscuro 0,1
Tabla 14. Factor de reflexión en función del material de suelos y otros revestimientos. Fuente:
Ramírez Vázquez, J. (1990). Luminotecnia. Enciclopedia CEAC de electricidad. 7ª ed. Ediciones CEAC.
• Coeficiente de utilización o factor de utilización (Cu). Se obtiene entrando en las
siguientes tablas dadas por el fabricante de la luminaria elegida con los valores del
coeficiente del local (K) y de los factores de reflexión (ρparedes, ρsuelo, ρtecho).
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 55
Aparato de alumbrado
Índice del
local K
Factores de utilización ρt = 0,7 ρt = 0,5 ρt = 0,3
ρp = 0,5 ρp = 0,3 ρp = 0,1 ρp = 0,5 ρp = 0,3 ρp = 0,1 ρp = 0,5 ρp = 0,3 ρp = 0,1 1 0,27 0,21 0,17 0,26 0,21 0,17 0,26 0,21 0,17
1,2 0,32 0,26 0,21 0,31 0,25 0,21 0,30 0,25 0,21 1,5 0,38 0,32 0,27 0,37 0,32 0,27 0,36 0,31 0,27 2 0,46 0,40 0,36 0,45 0,40 0,36 0,44 0,39 0,36
2,5 0,51 0,46 0,42 0,50 0,46 0,42 0,49 0,45 0,42 3 0,55 0,50 0,46 0,54 0,50 0,46 0,53 0,49 0,46 4 0,61 0,56 0,53 0,60 0,56 0,53 0,59 0,55 0,53 5 0,64 0,60 0,57 0,63 0,60 0,57 0,62 0,60 0,57 6 0,67 0,63 0,61 0,66 0,63 0,60 0,65 0,62 0,60 8 0,70 0,67 0,65 0,69 0,67 0,65 0,68 0,66 0,65
10 0,72 0,70 0,68 0,71 0,69 0,67 0,71 0,69 0,67 1 Aparato de alumbrado en el centro del local
1 0,29 0,23 0,19 0,28 0,23 0,19 0,28 0,23 0,19 1,2 0,35 0,29 0,25 0,34 0,29 0,25 0,33 0,28 0,25 1,5 0,42 0,37 0,33 0,41 0,36 0,33 0,41 0,36 0,33 2 0,52 0,47 0,44 0,51 0,47 0,44 0,50 0,47 0,44
Tabla 15. Cálculo de proyectos de iluminación interior. Lámparas incandescentes. Iluminación directa.
Fuente: Manual Práctico de Iluminación. Iluminación de Interiores. Autor: Franco Martín Sánchez. 2005.
ISBN: 84-87440-10-X.
Aparato de alumbrado
Índice del
local K
Factores de utilización ρt = 0,7 ρt = 0,5 ρt = 0,3
ρp = 0,5 ρp = 0,3 ρp = 0,1 ρp = 0,5 ρp = 0,3 ρp = 0,1 ρp = 0,5 ρp = 0,3 ρp = 0,1 1 0,27 0,21 0,17 0,25 0,20 0,16 0,23 0,19 0,15
1,2 0,32 0,26 0,21 0,30 0,24 0,20 0,27 0,23 0,19 1,5 0,38 0,32 0,27 0,35 0,30 0,26 0,33 0,28 0,24 2 0,46 0,40 0,35 0,43 0,37 0,33 0,39 0,35 0,32
2,5 0,51 0,45 0,41 0,47 0,43 0,39 0,44 0,40 0,36 3 0,55 0,50 0,45 0,51 0,47 0,43 0,47 0,44 0,40 4 0,60 0,56 0,52 0,56 0,52 0,49 0,52 0,49 0,46 5 0,64 0,60 0,56 0,60 0,56 0,53 0,56 0,53 0,50 6 0,66 0,63 0,59 0,62 0,59 0,56 0,58 0,56 0,53 8 0,70 0,67 0,64 0,66 0,63 0,61 0,61 0,59 0,57
10 0,72 0,69 0,67 0,68 0,65 0,63 0,64 0,67 0,60 1 Aparato de alumbrado en el centro del local
1 0,29 0,23 0,19 0,27 0,22 0,18 0,25 0,20 0,17 1,2 0,34 0,28 0,24 0,32 0,27 0,23 0,30 0,25 0,22 1,5 0,41 0,36 0,31 0,39 0,34 0,30 0,36 0,32 0,28 2 0,51 0,46 0,42 0,48 0,43 0,40 0,45 0,41 0,38
Tabla 16. Cálculo de proyectos de iluminación interior. Lámparas incandescentes. Iluminación
semidirecta. Fuente: Manual Práctico de Iluminación. Iluminación de Interiores. Autor: Franco Martín
Sánchez. 2005. ISBN: 84-87440-10-X.
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 56
Aparato de alumbrado
Índice del
local K
Factores de utilización ρt = 0,7 ρt = 0,5 ρt = 0,3
ρp = 0,5 ρp = 0,3 ρp = 0,1 ρp = 0,5 ρp = 0,3 ρp = 0,1 ρp = 0,5 ρp = 0,3 ρp = 0,1 1 0,29 0,24 0,20 0,29 0,23 0,20 0,28 0,23 0,20
1,2 0,35 0,29 0,25 0,34 0,28 0,25 0,33 0,28 0,24 1,5 0,41 0,36 0,31 0,41 0,35 0,31 0,40 0,35 0,31 2 0,50 0,45 0,41 0,49 0,44 0,41 0,48 0,44 0,41
2,5 0,55 0,50 0,47 0,54 0,50 0,46 0,53 0,50 0,46 3 0,59 0,55 0,51 0,58 0,54 0,51 0,58 0,54 0,51 4 0,65 0,61 0,58 0,64 0,60 0,58 0,63 0,60 0,57 5 0,68 0,65 0,62 0,67 0,64 0,62 0,66 0,64 0,62 6 0,70 0,67 0,65 0,69 0,67 0,65 0,69 0,67 0,65 8 0,73 0,71 0,69 0,72 0,71 0,69 0,72 0,71 0,69
10 0,75 0,73 0,71 0,74 0,73 0,71 0,74 0,73 0,71 1 Aparato de alumbrado en el centro del local
1 0,32 0,26 0,22 0,31 0,26 0,22 0,30 0,26 0,22 1,2 0,38 0,33 0,29 0,37 0,32 0,29 0,37 0,32 0,29 1,5 0,46 0,41 0,38 0,46 0,41 0,38 0,45 0,41 0,38 2 0,57 0,53 0,50 0,57 0,53 0,50 0,56 0,53 0,50
Tabla 17. Cálculo de proyectos de iluminación interior. Lámparas fluorescentes. Iluminación directa
con armadura sencilla. Fuente: Manual Práctico de Iluminación. Iluminación de Interiores. Autor: Franco
Martín Sánchez. 2005. ISBN: 84-87440-10-X.
Un coeficiente de utilización alto indica que una gran parte del flujo luminoso
producido en la lámpara o lámparas de las luminarias se aprovecha en el plano de
trabajo [12]. El coeficiente de utilización (Cu) es tanto mayor cuanto:
o Mayores son los factores de reflexión de techo, paredes y suelo.
o Mayores son la longitud “L” y la anchura del local “A”.
o Menor es la altura del plano de trabajo “h”.
• Coeficiente o factor de conservación de las lámparas “Cc”. Los valores de flujo
luminoso dados por el fabricante de las lámparas son para una lámpara nueva y limpia.
Sin embargo, a lo largo de la vida útil de la lámpara se produce una disminución del
mismo por [16]:
o Envejecimiento de la lámpara (es irreversible).
o Ensuciamiento de la lámpara (puede solucionarse limpiándola).
En la tabla 18 se dan los valores del coeficiente de conservación (Cc) teniendo en
cuenta lo anterior.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 57
TIPO DE MANTENIMIENTO
COEFICIENTE DE CONSERVACIÓN Luminaria AL AIRE
Luminaria ABIERTA
Luminaria CERRADA
Luminaria ESTANCA
Bueno 0,70 0,75 0,80 0,90 Medio 0,60 0,60 0,70 0,80 Malo 0,50 0,50 0,55 0,70
Tabla 18. Coeficientes de conservación. Fuente: Luminotecnia. Iluminación de Interiores y exteriores. D.
Oriol Boix Aragonés. Departamento de Ingeniería Eléctrica de UPC. Septiembre de 1999. ISBN: 84-600-
9647-5. http://edison.upc.edu//curs.ilum.
Para las lámparas de uso domestico se puede considerar que el mantenimiento es medio
por lo siguiente:
o Las condiciones ambientales son menos limpias que en un mantenimiento
bueno donde el aire es filtrado.
o Las luminarias no se limpian frecuentemente.
o Las lámparas se sustituyen solamente conforme se van fundiendo.
• Número de lámparas y luminarias. Para determinar el número de lámparas y
luminarias se siguen los siguientes pasos:
o Determinamos el flujo luminoso total necesario para la iluminación del local,
que viene dado por [15]:
CcCuSEm
⋅⋅
=Φ total
donde:
Φ total (lm): Flujo luminoso total en lúmenes.
Em (lx): Nivel medio de iluminación necesario en el local.
S (m2) = a·b: Superficie en planta del local.
Cu: Coeficiente de utilización del local.
Cc: Coeficiente de conservación de la lámpara.
o Determinamos el número necesario de luminarias (Nlum) en el local con la
expresión:
lámpara
totallum Φ⋅
Φ=
lumnN
Capítulo 1: Introducción. Iluminación
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 58
donde:
Φ lámpara (lm): Flujo luminoso producido por la lámpara.
nlum: Número de lámparas dentro de una luminaria.
Se situará en el local un número de luminarias igual o inmediatamente superior al
obtenido.
o Finalmente calculamos el número necesario de lámparas mediante la formula:
Normalmente interesa disponer muchas luminarias de no mucha potencia en lugar
de pocas luminarias de mucha potencia, para conseguir así un adecuado coeficiente de
uniformidad.
• Nivel de iluminación final con el número de luminarias adoptado. Viene dado
por la expresión:
SCcCunN
E lumfinallum ⋅⋅Φ⋅= − ·lampara
final-m
REFERENCIAS
[1] Andrés DJR. Curso de Iluminación. Luminotecnia. Universidad de Málaga.
http://exp-grafica.uma.es.
[2] Espín EA, Aznar DF, Manzano ER, Espín MA. Luminotecnia Básica para
Ingenieros. ISBN 978-84-92680-10-8;2009.
[3] Álamos HJA. Luminotecnia. Iluminación. Generalidades. www.elprisma.com.
[4] Martín SF. Manual Práctico de Iluminación. Magnitudes Luminosas
Fundamentales. Unidades y Medidas. ISBN 84-87440-10-X;2005.
[5] Carrión RPM. Luminotecnia. El Color y la Luz. Universidad de Toledo.
[6] Foster R. Tipos de lámparas e Iluminación. Enciclopedia de Salud y Seguridad
en el Trabajo. Capitulo 46. Ministerio de Trabajo y Asuntos Sociales. www.mtas.es.
[7] IDAE. Guía Técnica de la Iluminación Eficiente. Sector Residencial y Terciario.
Fundación de la Energía de la Comunidad de Madrid;2006.
[8] Electrónica Industrial, S.L. El Mundo de las Lámparas. www.silix.es.
Nlamparas = Nlum · nlum
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 59
[9] Martín SF. Manual Práctico de Iluminación. Luminarias. ISBN 84-87440-10-
X;2005.
[10] IDAE. Aplicaciones Eficientes de Lámparas. Comité Español de Iluminación
(CEI), Instituto para la Diversificación y Ahorro de la Energía. Cuadernos de Eficiencia
Energética en Iluminación nº 1;1996.
[11] IDAE. Aplicaciones Eficientes de Luminarias. Comité Español de Iluminación
(CEI), Instituto para la Diversificación y Ahorro de la Energía. Cuadernos de Eficiencia
Energética en Iluminación nº 2;1996.
[12] Martín SF. Manual Práctico de Iluminación. Iluminación de Interiores. ISBN:
84-87440-10-X;2005.
[13] McGraw-Hill. Iberdrola. Ente Vasco de la Energía Técnicas y Aplicaciones de
la Iluminación. 1ª edición.: Serie McGraw-Hill de Electrotecnologías.
[14] Ramírez VJ. Sistemas de Iluminación. Proyectos de Alumbrado. Ediciones
CEAC. Enciclopedia CEAC de Electricidad. Barcelona 1974-1977.
[15] Boix AO. Luminotecnia. Iluminación de Interiores y exteriores.UPC. ISBN 84-
600-9647-5. http://edison.upc.edu//curs.ilum;1999.
[16] Luminotecnia Arquitectónica y Urbana. LAU 611. http://editorial.cda.ulpgc.es.
Objetivos/Metodología
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 60
OBJETIVOS
A lo largo de este apartado se exponen los objetivos, tanto generales como
específicos que se han marcado para la presente tesis.
Como se ha señalado anteriormente, el importante volumen de construcción de
edificios para uso residencial en los últimos años y el déficit en fuentes de energía
convencionales justifican las actuaciones que tengan como objetivo conseguir la
autosostenibilidad energética de los usos relacionados con la vivienda residencial. Las
instalaciones fotovoltaicas integradas en los edificios puede ser una alternativa
interesante para conseguirla.
El objetivo general de la investigación que aquí se plantea responde, en base a todo
lo anteriormente expuesto, al Uso de la energía solar fotovoltaica como fuente para el
suministro de energía eléctrica en el sector residencial. La finalidad de la investigación
es a) obtener la capacidad energética de las instalaciones fotovoltaicas conectadas a red
que se podrían ubicar en las cubiertas de los edificios b) desarrollar un modelo que
permita conocer la evolución y comportamiento del consumo de energía eléctrica en el
sector residencial relacionado con el uso final de iluminación c) determinar el
porcentaje de energía eléctrica para uso lumínico que podría ser cubierto por la energía
generada.
Los objetivos específicos de la investigación recogida en esta memoria de tesis son
los siguientes:
1) Analizar el marco normativo que rige el proceso edificatorio en relación con
el uso de la energía renovable estudiando la evolución en la implantación de
distintas tecnologías relacionadas con la energía en los edificios.
2) Obtención de datos de radiación solar media diaria y horaria y de
temperatura mediante la evaluación de un nuevo modelo para la
determinación de la radiación solar media diaria y horaria teniendo como
base la temperatura.
3) Calculo de la energía eléctrica generada por las instalaciones fotovoltaicas
conectadas a red ubicadas en las cubiertas de los edificios.
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 61
4) Diseño de un modelo para conocer la evolución y comportamiento del
consumo de energía eléctrica en el sector residencial relacionado con el uso
final de iluminación.
METODOLOGÍA
En relación con los objetivos especificos, señalados anteriormente, se han llevado a
cabo diversas metodologias con el objeto de alcanzar dichos objetivos. En cada uno de
los capítulos siguientes se desarrollan las mismas.
Capítulo II: Marco Normativo
Capitulo 2: Marco Normativo
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 62
THE USE OF SOLAR ENERGY IN THE BUILDINGS
CONSTRUCTION SECTOR IN SPAIN Javier Ordóñez Garcíaa, Eulalia Jadraque Gagoa, Javier
Alegre Bayoa, Germán Martínez Montesb aDr. Ingeniero de Caminos, Canales y Puertos, Department of Civil Engineering,
ETS de Ingenieros de Caminos, University of Granada, 18071 Granada, Spain bDr. Ingeniero de Caminos, Canales y Puertos, Proyectos de Ingeniería, Departamento de Ingeniería
Civil,
ETS de Ingenieros de Caminos, University of Granada, 18071 Granada, Spain
Abstract
The recent commitment made by many countries to combat the harmful effects of
fossil fuel energy has centered world attention on the implementation of policies geared
towards an optimal energy performance and the use of renewable energies. The
construction of buildings with sustainable energy systems necessarily plays an
important role in such policies, given the fact that in 2005 more than 800,000 housing
units were constructed in Spain, a country with more than 2500 h of sunlight per year.
This article reviews the European and Spanish legislation regarding construction and
renewable energies. Within this context, a description and analysis are given of the
progress made by the construction sector in the implementation of new energy-related
technologies with special emphasis on solar energy. ©2006 Elsevier Ltd. All rights reserved.
Keywords: Solar energy; Construction sector; Building
1364-0321/$ - see front matter © 2006 Elsevier Ltd. All rights reserved.
doi:10.1016/j.rser.2006.03.010
Javier Ordóñez García et al., 2007
The use of photovoltaic solar energy as an energy source in the residential housing sector 63
1 INTRODUCTION
In the last five years there has been a spectacular construction boom in Spain.
According to the National Association of Architects,1 the number of new housing units
in this period has doubled, going from 400,000 in 2000 to a record 800,000 in 2005.
Because of its geographic location, Spain has over 2500 h of sunlight per year, and is
the European country with the third highest quantity of photovoltaic power, amounting
to 11.7 MWp in 2004. However, when it comes to using solar energy for domestic
activities such as heating water, Spain lags farther behind, only ranking eighth. This fact
is significant because domestic energy use is intimately related to the construction
sector [1]. Spain’s low ranking here means that the country still has a long way to go to
fully benefit from this type of energy, and that greater use should be made of solar
power in the design and construction of houses. It is our assertion that in a national
context in which there is a record-breaking number of new housing units built every
year, it is crucial to see exactly how the issue of energy supply is presently being dealt
with. The construction boom in Spain also comes at a time when an increasing number
of voices are being raised in favor of the development and construction of sustainable
housing [2]. There are a wide range of possible measures that could be taken to foment
the use of renewable energies [3]. One possibility would be to oblige architects and
developers to include a set of minimum requirements for efficient energy use in the
project designs of new buildings, as well as to inform the purchaser and/or client of the
contents of European Directive 2002/91/EC on the Energy Performance of Buildings
[4].
In this article, we analyze European and Spanish legislation that regulates the use of
renewable energy in the construction of housing developments. We emphasize the fact
that the legislative framework regarding construction will soon experience significant
modification in the near future with the passing of the Código Técnico de la
Edificación2 (CTE). The purpose of our study is to review the European and Spanish
legislation concerning construction and renewable energies [5], as well as to describe
the progress made by the construction sector in the implementation of new energy-
related technologies with special emphasis on the use of solar energy. 1 In Spain this type of professional association is known as the Colegio de Arquitectos. 2 Technical Building Code.
Capitulo 2: Marco Normativo
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 64
2 SOLAR ENERGY IN SPAIN
Spain is located in the south eastern part of Europe (see Fig. 1). More specifically, it
is situated in the temperate zone between latitudes 43º47´24´´ N (Estaca de Bares) and
36º00´3´´ S (Punta de Tarifa); and between longitudes 7º00´29´´ E (Cape Creus) and
5º36´40´´ W (Cape Touriñan). It has a surface area of 580,850 km2.
Fig. 1. The geographic location of Spain on the European continent.
To the north, it is bordered by the Cantabrian Sea, France, and Andorra; to the east,
by the Mediterranean Sea and the Atlantic Ocean; to the south, by the Atlantic Ocean;
and to the west, by the Atlantic Ocean and Portugal. Although Spain is located in a
temperate zone, it has the following climate distribution [6] (see Fig. 2):
• Oceanic climate: Galicia and the Cantabrian coastline. These areas have mild
temperatures and abundant rainfall.
• Mediterranean climate: the Mediterranean coastline. This climate is
characterized by hot, dry summers, little rainfall, and mild winters. Rainfall is generally
more frequent in spring and autumn, when a cold air pool may occur, resulting in
intense torrential rains. Periods of drought alternate with periods of abundant
precipitation.
Javier Ordóñez García et al., 2007
The use of photovoltaic solar energy as an energy source in the residential housing sector 65
• Highland climate: the Pyrenees, the Sistema Central3 and the Penibetic
Mountain Range. Winters are long and cold with abundant rainfall.
• Continental climate: the interior of the Iberian Peninsula. This area has cold
winters and hot summers because of its distance from the coastline. Storms frequently
occur during the summer months.
• Subtropical climate: the Canary Islands. The temperatures are mild throughout
the year with relatively low levels of precipitation.
Thanks to its geographic location and climate, Spain is in a privileged position in
comparison to other European countries since each square meter of its surface area
receives 1500 kWh of energy. This figure is similar to that of many Central and South
American countries. In fact, in various areas of Spain, there are over 2500 h of sunlight
per year [7] (see Fig. 3).
Fig. 2. Climate distribution in Spain.
From the beginning of civilization, men have resorted to bioclimatic architectural
methods to significantly reduce and even eliminate the need to artificially heat/cool their
homes and light them during the day. With a view to taking greater advantage of
sunlight, they would design houses whose windows, doors, balconies, facades, and
patios faced the south. They would build glassed-in porches and huge fireplaces to light
inside areas. They would whitewash door and window frames to enhance the sensation 3 Mountain range on the Iberian Peninsula, consisting of several smaller mountain ranges, which is a
primary feature of the Iberian plateau (Meseta Central).
Capitulo 2: Marco Normativo
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 66
of brightness, and would use skylights and glassed-in balconies as solar collectors. They
tried to mitigate the unpleasant effects of excessive sunlight (glare and heat) in the
inside of houses by making roofs overhang significantly and by prolonging the cornices
on windows and entrances. They protected balconies by means of small projections that
acted as shade. Decorative grille work and wooden lattices were placed on windows to
filter out sunrays. Transoms and openings were put above front doors for better
ventilation. Porches were protected with trellises, and high walls shielded the grounds
surrounding the house [8].
Without recurring to any other device, such buildings made passive use of solar energy
through the suitability of their location, design and orientation, the correct use of the
physicochemical properties of materials, as well as architectural elements such as
soundproofing, insulation, type of covering, protections, etc. However, such measures,
though useful, are no longer sufficient in themselves. It is now time to branch out to a
wider and more active use of solar power by capturing thermal energy (heat) with solar
sensors or by generating electricity with photovoltaic cells [9].
Fig. 3. Energy in kW/h/m2 surface area per year/hours of sunLight.
Javier Ordóñez García et al., 2007
The use of photovoltaic solar energy as an energy source in the residential housing sector 67
3 LEGISLATION REGARDING CONSTRUCTION
3.1 Europe
In order to promote and encourage the use of solar energy, in December 1997 the
European Union passed the White Paper for a Community Strategy and Action Plan.
Energy for the Future: Renewable Sources of Energy, and proposed as an objective for
2010 that renewable energies supply 12% of the primary energy demands of the
European Union [10].
The European Union Green Paper entitled Towards a European Strategy for the
Security of Energy Supply, specifically states that one of its priorities is the integration
of renewable energies in new constructions through regulations obliging heating and air
cooling systems to necessarily depend on these energy sources [11].
In the case of solar thermal energy, the EU White Paper seeks to increase the
number of sensors from 6.5 square meters in 1995 to 100 million square meters in 2010
[12]. The purpose of European directive 2002/91/CE is to encourage the use of solar
photovoltaic and thermal renewable energies [13]. In this sense, important
considerations are external climatic conditions and local characteristics as well as the
environmental requirements and the cost-efficiency relation. One of the major
objectives here is to improve the energy performance of buildings since such structures
have a significant long-term impact on energy consumption (heating and air cooling
systems, water heating, and electricity) [14].
3.2 Spain
Legislation regarding construction has experienced important changes since the
passing in 2002 of the European Directive on Energy Performance, 2002/91/CE and its
transposition to Spanish law at the end of 2005 [14].
The plan to encourage the use of renewable energies has the same global objective
as the European Union in its White Paper on Renewable Energies, which states that at
least 12% of the total energy demand in Spain should be covered by renewable energy
sources [15].
Capitulo 2: Marco Normativo
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 68
The Ley de Ordenación de la Edificación, Law 38/19994 of November 5, 1999
establishes three sections of basic demands, which refer to the functionality, safety, and
habitability of buildings. The habitability section regulates the economical use of energy
and thermal insulation with a view to achieving rational energy use for the optimal
functionality of buildings. This means reducing energy consumption to sustainable
levels, and having at least a portion of this consumption come from renewable energy
sources [16].
Within this context, there are new regulations which regard the following [14]:
• Minimum requirements of energy performance regarding illumination,
soundproofing, insulation, heating, air condition, and sanitary hot water in buildings.
• Energy certification for buildings.
• Use of solar photovoltaic and thermal renewable energy.
The legal measures taken in Spain in response to these new demands are specified in
the following laws:
(1) The CTE5 that defines and establishes the basic requisites for safety and
habitability that should be fulfilled by buildings, and which stipulates the requirements
that must be complied with in the project design, construction, use, maintenance, and
conservation of buildings with a view to enhancing their quality, guaranteeing the health
and safety of occupants, and protecting the environment in the immediate surroundings
[17].
This code establishes the following set of objectives
• To limit energy demands through the optimization of building designs, taking
into account all the techniques of bioclimatic architecture and passive solar energy. For
the first time the CTE also includes energy performance criteria for lighting
consumption.
• To improve the performance of heating systems through the incorporation of
inspections and audits of such installations, and providing solutions to make them more
efficient.
• To incorporate solar thermal energy for sanitary hot water. For new buildings
this will be obligatory. Depending on the climate zones, between 30% and 70% of the
energy demand for sanitary hot water should come from solar energy.
4 Law of Building Organization. 5 Technical Building Code.
Javier Ordóñez García et al., 2007
The use of photovoltaic solar energy as an energy source in the residential housing sector 69
• To implement solar photovoltaic energy in building complexes with high energy
consumption. Consequently, solar photovoltaic panels will be obligatory in hotels and
hospitals (>100 occupants or beds), multimedia centers (>3000 m2), office buildings
(4000 m2), hypermarkets (>5000 m2) and fair pavilions (>10,000 m2). This means
installing power between 6.25 and 62.5 kWp. Moreover, all installations of up to 100
kW will be included in the current power rates of 0.4 euros/kW h. (Previously, this was
only applicable to installations of up to 5 kW.)
(2) The Plan de Fomento de las Energías Renovables6 (PFER) [18] describes the
principal elements and guidelines that can be considered relevant in designing a strategy
so that the growth of renewable energies as a whole can cover at least 12% of all
primary consumption by 2010. However, this objective can only be reached if a greater
percentage of such energies is used in buildings, and more specifically, in their heating
systems, where energy consumption is the highest. The Reglamento de Instalaciones
Térmicas7 (RITE) and its Instrucciones Técnicas Complementarias8 (ITE) establish the
requirements for heating systems in buildings. These regulations are in response to the
public demand for thermal comfort and hygiene in heating, cooling, and sanitary hot
water systems. The objective of these regulations is to promote a more rational level of
energy consumption for economic as well as environmental reasons. In a parallel way,
other considerations to be taken into account are the basic construction and design
requirements for buildings. In the interest of economic viability, all of these factors
must be maintained during an important part of the useful life of the structure [19].
These regulations are divided into two sections. The first section includes the RITE
and the ITE. The second section, which is basically informative, is an annex of relevant
documents for reference purposes. The following is a summary of the ITEs that
explicitly mention renewable energies:
• ITE 02.4.1. Design. Heating and cooling systems. General description:
According to this document, the choice of a heating and cooling system makes it
necessary to examine the possibility of using subsystems of energy conservation and
recovery as well as the exploitation of free/renewable energies.
6 Plan to promote renewable energies. 7 Regulations for thermal systems. 8 Complementary technical instructions.
Capitulo 2: Marco Normativo
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 70
• ITE 02.4.12. Design. Heating and cooling systems. Electric Energy: According
to this document, in both residential and government buildings that use electrical energy
by the Joule effect for heating, the global transmission coefficient of the building (KG)
should not be greater than the boundary value established for this energy source. This
would be the case for buildings without heating or which are heated with electrical
energy by the Joule effect, as stated in regulation NBE-CT concerning heating systems
in buildings [20]. Premises excluded from this requisite, and which thus must comply
with the conditions set out in case I (solid, liquid or gaseous fuels) are those using
residual or free energy sources as well as electrical energy as an auxiliary energy source
as long as the annual coverage of the residual/free energy source is more than two-
thirds.
• ITE 02.5.4. Design. Central production of sanitary hot water. Use of electrical
energy for the production of sanitary hot water: The use of electrical energy for
sanitary water heating through the Joule effect in central sanitary hot water systems is
permitted when it is used as a support for residual/free energy sources, and always as
long as these sources cover more than two-thirds of the total energy demand.
• ITE 04.9.1. Equipment and Materials. Boilers. General conditions: According to
this document, boilers not subject to Real Decreto9 275/1995 are those that run on solid,
liquid and gaseous fuels, with characteristics or specifications that differ from those
fuels generally sold, and which are derived from the recovery of effluents, side products
or waste matter, whose combustion is not affected by environmental impact limitations
(e.g. waste gas, bio-gas, biomass, etc.).
• The RITE includes as a novelty an ITE 10.1, entitled Producción de ACS
mediante sistemas solares activos,10 which specifically refers to low-temperature flat
solar energy collectors for the heating of sanitary hot water installed at the building site.
• ITE 10.2. Specific installations. Swimming pools: According to these regulations,
openair swimming pools can only use waste/free, energy sources like solar energy for
heating water.
(3) The creation of an Energy Certification for Buildings [21]. The Energy
Performance Certification of a building is a certificate recognized by the State or a
person designated by the State who verifies that the building is energy efficient on the
9 A national law in Spain is known as a royal decree [Real Decreto (R.D.)]. 10 Production of ACS with active solar energy systems.
Javier Ordóñez García et al., 2007
The use of photovoltaic solar energy as an energy source in the residential housing sector 71
basis of calculations established according to a specific methodology. When buildings
are constructed, sold, or rented, this certificate with a validity of up to 10 years is made
available to the owner or purchaser of the building by the former owner. This certificate
gives objective information regarding the energy characteristics of the building to
possible buyers or users. Consequently, it is conducive to greater transparency in real
estate development and foments investments in energy-saving techniques.
4 METHODOLOGY
In order to carry out our study, we compiled statistics from 1996, which were
obtained from the Dirección General de Programación Económica de la Secretaría de
Estado de Infraestructuras,11 an agency that depends on the Ministerio de Fomento or
the Spanish Ministry of Public Works and Economy. The role of this Ministry in Spain
is to propose and implement government policies concerning land, sea, and air
transportation as well as their control, organization and regulation, the administration of
postal and telegraphic services, the guidance and management of national agencies
related to astronomy, geodetics, geophysics and cartography, and finally the planning
and organization of all investments related to these areas [22].
The data for this study was obtained by using a questionnaire, on the basis of the
construction licenses granted by the city halls. For the construction of new buildings, a
license is necessary. Such a license can only be obtained by presenting the project
design of the new building, which must be signed by the architect. Consequently, this is
an administrative procedure that gives privileged information regarding the number and
characteristics of buildings as well as the type of housing units that this construction
generates [22].
The focus of this study is on residential buildings in construction. For our purposes,
a residential building is defined as any permanent, separate, independent structure
whose main purpose is to be occupied by people on a continuous basis (at least 50% of
its useful surface with the exclusion of its ground floor and basement). A house is
defined as an enclosed space or a set of various rooms and annexes that may occupy the
entire surface of a building (one-family house) or part of a building, which in this case
would be structurally separate and independent from the rest. A house is designed to be
11 Government Office of Economic Planning of the Secretariat of Infrastructure.
Capitulo 2: Marco Normativo
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 72
occupied by people, generally families of one or various members, and can be directly
accessed from the public highway or from shared neighborhood spaces.
In Spain the Ministerio de Fomento collects data on a monthly basis for the whole
country. The treatment of the response ‘‘no answer given’’ on certain questionnaires is
handled by stratifying city halls in provinces by calculating expansion coefficients
based on the city population and the number of licenses granted. The formula used is the
following:
Cij = Pij/pij · Lij/lij,
where Cij is the elevation coefficient of stratum i in province j, Pij, the population of
the towns of stratum i in province j, pij, the population of the towns of stratum i in
province j that have answered the questionnaire, Lij, the number of licenses granted in
stratum i in province j, lij, the number of licenses of stratum i in province j with
questionnaires. This expansion coefficient uses the first factor Pij/pij to correct the
refusal to answer, and Lij/lij to correct the non-completion of questionnaires. In order to
obtain the final results, questionnaires of each stratum-province are added up, and the
resulting figure is multiplied by the coefficient. The size of the sample (i.e. the
minimum number of towns that should be received from each stratum (n)), will depend
on the total number of towns (N), the desired confidence level (K), the variability of the
licenses granted (s), and the absolute error assumed for these licenses (e).
The formula used is the following:
n = N2K2S2 / (e2 + NK2S2).
5 RESULTS
The evolution of the number of housing units in Spain has undergone a spectacular
increase in the last decade. During 1980–1997 an average of 287,000 houses were built
each year [23]. From 1998, the number of houses constructed soared to over 400,000 a
year (see Fig. 4).
There is currently a great risk of environmental degradation due to population
increase, resource consumption, industrial activity, etc. This situation causes a series of
problems such as acid rain or the hole in the ozone layer. Some of these problems are
Javier Ordóñez García et al., 2007
The use of photovoltaic solar energy as an energy source in the residential housing sector 73
directly related to substances sent into the atmosphere as a consequence of fossil fuel
combustion or CFCs from air conditioning and cooling systems. Various authors
suggest the use of renewable energies as a possible solution for such problems [24].
EVOLUTION OF THE NUMBER OF HOUSING UNITS.
0
100.000
200.000
300.000
400.000
500.000
600.000
1996 1997 1998 1999 2000 2001 2002 2003 2004
Number of housing units
Fig. 4. Number of houses constructed in Spain. Data obtained from the Ministerio de Fomento.
EVOLUTION OF THE NUMBER OF BUILDINGS
0
20.000
40.000
60.000
80.000
100.000
120.000
140.000
160.000
180.000
200.000
1996 1997 1998 1999 2000 2001 2002 2003 2004
Number of buildings
Fig. 5. Number of buildings. Data provided by the Ministerio de Fomento.
On the basis of the data obtained, we show the evolution of the number of buildings
constructed in Spain, which has followed a progression similar to the number of
housing units (see Fig. 5). This is due to the fact that the proportion of different types of
houses (one-family houses, semi-detached house, and housing complex) is remarkably
similar over this time period within the national context.
Capitulo 2: Marco Normativo
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 74
During this period, it is surprising what little use has been made of renewable
energies in the construction sector. The data collected shows the number of buildings
and the different types of energies employed: electricity, natural gas, liquid petroleum
gas (LPG), and solar energy (see Fig. 6).
During the past decade, the total number of buildings with solar energy systems only
reached 2.5%. Solar energy systems began appearing in new houses in 1996, and is now
becoming increasingly more frequent (see Fig. 7). In 2004 the number of houses with
this type of energy was 23,249 in contrast to 256 houses with this energy system in
1996.
If we compare annual variations of the different types of energy installed in
buildings, we obtain the percentage of buildings per year that use a specific energy
source (see Figs. 7, 8).
EVOLUTION OF THE NUMBER OF BUILDINGS/TYPE OF ENERGY SYSTEM
INSTALLED
0
20.000
40.000
60.000
80.000
100.000
120.000
140.000
160.000
180.000
200.000
1996 1997 1998 1999 2000 2001 2002 2003 2004
Nª of buildings Electricity Natural Gas L.G.P. Solar Energy C. Sólido
Fig. 6. Evolution of the number of buildings/type of energy system installed. Data obtained from the
Ministerio de Fomento.
Javier Ordóñez García et al., 2007
The use of photovoltaic solar energy as an energy source in the residential housing sector 75
EVOLUTION OF THE PERCENTAGE OF BUILDINGS WITH SOLAR ENERGY
y = 0,0016e0,2713x
R2 = 0,8646
0,00%
0,50%
1,00%
1,50%
2,00%
2,50%
1996 1997 1998 1999 2000 2001 2002 2003 2004
% Solar Energy Exponencial (% Solar Energy)
Fig. 7. Percentage (%) of buildings with solar energy.
The graph shows that there has been a relative decrease in the number of buildings
with energy systems fuelled by LPG. In contrast, there has been an important increase in
the number of buildings that have installed natural gas and solar energy. The installation
of systems using solid and liquid fuel remains constant.
The tendency curve over the last four years shows the progressive implementation
of solar energy systems in residential buildings. As reflected in the graph, the number of
buildings with this technology went from 0.3% to 2.4% in four years, which means a
constant annual increase of 0.53 (see Fig. 9).
6 CONCLUSIONS
Spain is presently experiencing a spectacular construction boom. The number of
new houses built reaches new records each year. However, despite the fact that the
country has an annual average of 2515 h of sunlight, relatively little use has been made
so far of the possibilities offered by solar energy systems in buildings.
Capitulo 2: Marco Normativo
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 76
EVOLUTION OF THE PERCENTAGE % OF BUILDINGS WITH LGP, NATURAL GAS,
LIQUID FUEL
0,00%
5,00%
10,00%
15,00%
20,00%
25,00%
1996 1997 1998 1999 2000 2001 2002 2003 2004
Natural Gas L.G.P. Liquid fuel Solid Fuel
Fig. 8. Percentage (%) of buildings with different types of energy installed.
Tendency in the evolution of the percentage % of buildings w ith solar energy in recent years
y = 0,0057x + 0,0004R2 = 0,9997
0,00%
1,00%
2,00%
3,00%
4,00%
5,00%
6,00%
2001 2002 2003 2004 2005 2006 2007 2008 2009
Solar Energy Lineal (Solar Energy)
Fig. 9. Presence of solar energy in the construction sector.
In our opinion, the authorities have wasted too many years, and have thus lost an
historic opportunity to foment and encourage the use of solar energy. Even though solar
energy systems are gradually becoming more frequent in contrast to fossil fuel systems,
whose growth rate was very low and even decreased in some cases, there is still much to
be done.
The data collected in our study shows that although the use of solar energy is
gradually on the upswing, recourse to this energy source is still infrequent. This
signifies the urgent need for specific legal measures and government actions that will
subsidize and/or require the use of this technology in order to encourage its use in new
buildings.
Javier Ordóñez García et al., 2007
The use of photovoltaic solar energy as an energy source in the residential housing sector 77
REFERENCES
[1] Photovoltaic Barometer, EurObserver; April 2005.
[2] Halliday S. Sustainable construction. UK: Butterworth-Heinemann; 2005.
[3] Martinez G, Serrano MM, Rubio MC, Menendez A. An overview of renewable
energy in Spain. The small hydro-power case. Renew Sustain Energy Rev 2005;9:521–
34.
[4] Secretaria de Estado de Energía, Desarrollo Industrial y de la Pequeña y
Mediana empresa. Ministerio de Economía. Estrategia de Ahorro y Eficiencia
Energética en España 2004–2012. Sector Edificación; 2003.
[5] Jäger-Waldau A, Ossenbrik H. Progress of electricity from biomass, wind and
photovoltaics in European Union. Renew Sustain Energy Rev 2004;8:57–82.
[6] www.esi.unav.es. Escuela Superior de Ingenieros. Campus Tecnológico,
University of Navarra, Spain.
[7] www.censolar.es. Centros de Estudio de la Energía Solar.
[8] Cañas I, Martín S. Recovery of Spanish vernacular construction as a modelo f
bioclimatic architecture. Build Environ 2004;39:477–95.
[9] Greenpeace. Guía solar. Como disponer de energía solar fotovoltaica conectada
a la red eléctrica; 2005.
[10] Orden de 5 abril de 2000, por el que se hacen públicas las normas reguladoras
de la concesión de ayudas del Programa Andaluz de promoción de instalaciones de
energías renovables (PROSOL) para el periodo 2000–2006. BOJA, 11 May, 2000.
[11] European Union. Green paper: towards a European strategy for the security of
energy supply. 2000. p. 769.
[12] European Union. White paper for a community strategy and action plan.
Energy for the future: renewable sources of energy; 2000.
[13] Ackermann T, Andersson G, Söder L. Overview of government and market
driven programs for the promotion of renewable power generation. Renew Energy
2001;22(1–3):97–204.
[14] European Directive 2002/91/EC on the Energy Performance of Buildings.
[15] Ramos A, Hontoria E, Moreno B, Zamorano M. Solar energy in Andalusia
(Spain): present state and prospects for the future. Renew Sustain Energy Rev 2005;1–
14, in press, doi:10.1016/j.rser.2004.12.009.
Capitulo 2: Marco Normativo
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 78
[16] Ley 38/1999, de 5 de noviembre, de Ordenación de la Edificación. BOE no.
266, 6 November, 1999. p. 38925–34.
[17] Código Técnico de la Edificación. Documento Básico HE. Ahorro de energía,
November, 2003.
[18] Plan de Fomento de las Energías Renovables, 2000–2010.
[19] REAL DECRETO 1218/2002, de 22 de noviembre, por el que se modifica el
Real Decreto 1751/1998, de 31 de julio, por el que se aprobó el Reglamento de
Instalaciones Térmicas en los Edificios y sus Instrucciones Técnicas Complementarias
(ITE) y se crea la Comisión Asesora para las Instalaciones Térmicas de los Edificios.
BOE no. 289, 3 December, 2002.
[20] REAL DECRETO 2429/1979, de 6 de julio, por el que se aprueba la Norma
Básica de la Edificación NBECT-79. Condiciones térmicas en los edificios.
[21] Documento de Bases para la Revisión del RITE. Version 10/10/2003
(Document passed by the permanent subcommittee of the Advisory Committee on
heating systems in buildings), Ministerio de Economía, Ministerio de Fomento.
[22] REAL DECRETO 1476/2004, de 18 de julio por el que se desarrolla la
estructura orgánica básica del Ministerio de Fomento. BOE no. 148, 19 July, 2004.
[23] García-Montalvo J, Mas M. La vivienda y el sector de la construcción en
España, Editorial CAM; 2000.
[24] Dincer I. Renewable energy and sustainable development: a crucial review.
Renew Sustain Energy Rev 2000;4:57–75.
Capítulo III: Modelos de Descomposición para la Irradiancia Horaria y la Temperatura
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 79
INTER-RELATIONSHIP BETWEEN MEAN-DAILY
IRRADIATION AND TEMPERATURE, AND
DECOMPOSITION MODELS FOR HOURLY
IRRADIATION AND TEMPERATURE E J Gago**, S Etxebarria*, Y Tham*, Y Aldali* and T Muneer*
*School of Engineering and the Built Environment, Edinburgh Napier University, UK
** Department of Civil Engineering, University of Granada, Spain
Abstract
Terrestrial temperature records have existed for centuries. These records are
available for very many locations. Temperature is indeed the most widely measured
meteorological parameter. In contrast, solar radiation being a parameter of secondary
importance and also in view of the excessive measurement cost and the associated due
care, it is recorded very infrequently. This article presents evaluation of a new type of
model for mean-daily and hourly solar radiation based on temperature. The proposed
model is of a very simple constitution and does not require any secondary
meteorological parameters as required by other group of models that are available in
literature. Furthermore, hourly temperature models are also presented that only require
mean-daily temperature data.
A comparison was undertaken regarding the performance of the presently proposed-
and previous models. It was found that the present models are able to provide reliable
irradiation and hourly temperature estimates with a good accuracy.
Keywords: Solar radiation, solar energy, solar radiation regression models
International Journal of Low-Carbon Technologies 2011, 6, 22–37
© The Author 2010. Published by Oxford University Press. All rights reserved. For Permissions, please
email: [email protected]
doi:10.1093/ijlct/ctq039 Advance Access Publication 6 October 2010
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 80
1 INTRODUCTION
Solar radiation and daylight are essential to life on earth. Solar radiation affects the
earth’s weather processes which determine the natural environment. Its presence at the
earth’s surface is necessary for the provision of food for mankind. Thus it is important
to be able to understand the physics of solar radiation and in particular to determine the
amount of energy intercepted by the earth’s surface. The understanding of the
climatological study of radiation is however comparatively new. Until 2010 there were
only three stations in northwest Europe with irradiation records exceeding an 85-year
period. In the UK it was only in the 1950s that the Meteorological Office installed Kipp
solarimeters. In contrast, however, temperature has been recorded the world over at very
many locations and for a much longer period, e.g. the oldest records for temperature for
Central England have existed since 1659! In India, to give another example, the number
of sites with temperature records is 161, but only 18 stations measure irradiation.
Likewise, respectively, in Malaysia and Spain there exist 41 and 113 stations that
measure temperature, but only 9 and 33 stations record irradiation. Table 1 provides
information on the start dates for temperature records for England. It has also been
pointed out by Thorton and Running [1] and Rivington et al [2] that even in the most
developed countries such as the USA and Britain the landmass area covered by solar
radiation network is < 1%. Globally this figure is much worse. Solar irradiation
availability of arbitrary surfaces is a prerequisite in many sciences. For example,
agricultural meteorology, photobiology, animal husbandry, daylighting, comfort air-
conditioning, building sciences and solar energy utilization, all require this information.
In agricultural meteorology, the importance of net radiation in determining crop
evaporation is well documented. It has been suggested that in the annual enthalpy of
evaporation from short grass is equal to the annual net radiation. A similar case occurs
on a daily basis. Net radiation is also required in estimating the heating coefficient of a
field, which is a key index for soil germination temperature. The effects of solar
radiation are also of interest in the breeding of cattle and other livestock. It is usually the
major factor limiting the distribution of stock in the tropics. The heat load on an animal
is the result of solar irradiation and in some cases, its magnitude could be several times
the animal’s normal heat production.
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 81
Year Parameter recorded 1659 Monthly-mean temperature 1772 Daily-mean temperature 1878 Daily- and monthly-mean, maximum and minimum temperature
Table 1. Start dates for temperature measurement for Central England.
Month Air
temperature (°C)
Daily solar radiation - horizontal (kW·h/m2/d)
January 2.4 2.03 February 4.0 2.96 March 7.9 4.29 April 10.7 5.11 May 15.8 5.95 June 21.6 7.09 July 24.8 7.20 August 24.0 6.34 September 19.3 4.87 October 13.3 3.13 November 7.1 2.13 December 3.6 1.70
Table 2. Monthly-mean solar radiation and temperature for Madrid (40.38 N, 3.78 W). Source:
http://eosweb.larc.nasa.gov/cgi-bin/sse/[email protected].
For most of the above applications monthly averaged or daily solar radiation data is
adequate. The worldwide use of energy is rising by 2.5% a year, most of which is
attributable to the accelerated consumption in the developed and now developing
countries. It has been estimated that from a sustainability viewpoint, the developed
countries will have to cut their use of energy by a factor of 10 within a generation.
Proponents of solar energy have gone to the extent that they are calling for a complete
substitution of conventional sources of energy with renewables. Their thesis is that the
use of fossil fuels for energy production, even in minor quantities would merely
postpone the collapse of the global environment. The past three decades have seen a
boom in the construction of energy efficient buildings which use solar architectural
features to maximise the exploitation of daylight, solar heat, solar-driven ventilation and
solar PV electricity. These applications require hourly solar radiation and temperature
data. In most areas of the world, especially in the developing countries, solar radiation
measurements are not easily available due to the excessive cost and effort that is
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 82
involved. Air temperatures, on the contrary, are routinely measured at most
meteorological stations. As will be shown in the Section 2, NASA provides a useful
resource in terms of satellite observed data for monthly irradiation and temperature.
There is, however, a need to break down the daily data into the respective hourly
components, as there is a significant swing of hourly temperature within any given day.
Day Tmean Tmax Tmin
1 17.8 23.2 12.0 2 17.5 23.3 10.0 3 11.1 15.7 8.0 4 9.1 13.5 3.0 5 10.8 17.4 1.0 6 12.5 18.3 2.0 7 12.6 19.3 7.0 8 11.9 17.0 7.0 9 13.4 17.0 10.0
10 12.9 17.0 9.0 11 12.7 17.4 6.4 12 11.7 16.6 9.0 13 9.3 14.4 6.0 14 9.9 14.0 4.5 15 11.4 16.8 5.6 16 14.7 21.3 5.8 17 18.0 25.2 6.8 18 20.7 27.5 10.5 19 22.0 28.2 11.6 20 20.0 26.4 12.0 21 22.4 28.6 13.0 22 23.4 29.7 14.5 23 23.1 29.7 15.0 24 22.1 28.6 15.0 25 19.3 24.4 14.6 26 19.6 24.3 13.0 27 19.8 24.0 13.5 28 18.1 23.0 12.4 29 21.3 27.3 11.0 30 25.0 30.5 14.0 31 26.5 34.0 16.0
Table 3. Sample of the TUTIEMPO data set for Madrid (40.38 N, 3.78 W) for May 2010. Source:
www.TuTiempo.net.
The initial research related to solar radiation carried out by Angstrom [3] and others
was concerned with the relationship between irradiation and the sunshine duration.
Since then research in this field has come a long way. Today, a considerable amount of
information is available on mathematical models that relate solar radiation to other
meteorological parameters such as temperature, cloud-cover, rain amount, humidity and
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 83
even visibility. However, as pointed out above, the parameter that has the largest
measurement network is the ambient temperature. The aim of this work is to investigate
the inter-relationship between:
• mean-daily solar radiation and mean, maximum and minimum temperature;
• daily mean, maximum and minimum temperature; and
• hourly temperature and the corresponding mean-daily maximum and minimum
temperature.
2 PRESENTLY AVAILABLE INFORMATION
There are two reliable sources that provide information on the two of the most basic
meteorological parameters: monthly mean temperature and solar radiation. These
sources are the NASA website http://eosweb.larc.nasa.gov/cgi-
bin/sse/[email protected] and TUTIEMPO that is maintained by
http://www.tutiempo.net/en/. NASA has produced a grid map of the world with
information available for any given latitude and longitude. The solar radiation data is an
estimate that has been produced from satellite-based scans of terrestrial cloud-cover.
Typical tabulated information that may be downloaded from this source is shown in
Table 2. Note that NASA does not provide the mean-daily maximum and minimum
temperature. TUTIEMPO on the other hand provides daily mean, maximum and
minimum temperature data for any given location. The data is based on measurements
carried out by a wide network of meteorological stations and hence this latter data are
more reliable. One of the subtasks of this work is also to check the reliability of the
NASA temperature records by comparing them against the TUTIEMPO set. Table 3
presents a sample of the TUTIEMPO data set. Note that the NASA data is available on
a mean-monthly basis, whereas the latter data are downloadable on a day-by-day basis.
Thus by extension of the present work, one may obtain irradiation estimates for daily
irradiation using the TUTIEMPO data. The present article deals with mean-monthly
estimates.
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 84
Daily‐mean temperature, Tmean
Daily‐mean irradiation,
Daily‐meanmaximum temperature, Tmax
Daily‐meanminimum temperature, Tmin
Hourly‐mean temperature, Th
Mean‐hourly irradiationG
Figure 1. Flow diagram for obtaining hourly solar irradiation and temperature from mean-daily
temperature.
This section is concluded by pointing out two things that qualify this study, i.e. (i)
NASA data is based on satellite observations that represent inferred values of
irradiation. In contrast, TuTiempo provides ground-measured data for temperature.
Hence, if reliable regressions are available between irradiation and mean temperature
then the latter data may be used to obtain more realistic estimates of irradiation. (ii)
TuTiempo provides mean-minimum and maximum temperatures. Those can be used to
decompose daily to hourly temperatures.
3 PREVIOUS WORK
As mentioned above solar radiation can be estimated by means of empirical
relations using other available meteorological observations such as (a) mean-daily
sunshine duration, (b) cloud-cover, (c) ambient temperature along with precipitation
and/or humidity or (d) ambient temperature as the sole regressor. An exhaustive review
of the above methods is available in standard references [4-6]. In this article, effort has
been concentrated on models that exclusively deal with ambient temperature as the sole
predictor or regressor and as such models dealing with other meteorological parameters
are not dealt here. The theme of the present work stems from the logic that temperature
records have existed for a very long time and also the measurement network is indeed
very wide. Hence an irradiation model of the type that is presently proposed would be of
benefit, particularly for those in the developing countries where there is a dearth of
measured irradiation data.
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 85
Location Latitude Longitude Altitude Accra 5.60 -0.16 68
0-20
Georgetown 6.50 -58.25 29 Con Son 8.68 106.58 9 Juan Santamaria 9.98 -84.21 920 Barcelona. V 10.11 -64.68 7 Cartagena 10.45 -75.51 1 Caracas 10.60 -66.98 43 Babanusa 11.33 27.81 453 Phnom-Penh 11.55 104.85 10 Madras 13.00 80.18 10 Bangkok 13.66 100.56 4 San Salvador 13.70 -89.11 616 La Esperanza 14.31 -88.16 1,100 Guatemala 14.58 -90.51 1,489 Sanaa 15.51 44.20 2,206 Abbs 16.08 43.16 2,000 Timbuktu 16.71 -3.00 263 Acapulco 16.83 -99.93 28 Mexico 19.43 -99.10 2,238 Akola 20.70 77.03 282
Location Latitude Longitude Altitude Makkah 21.43 39.83 310
20-40
Aswan 23.96 32.78 200 Kufra 24.21 23.30 417 Riyadh 24.70 46.71 635 Manama 26.26 50.65 2 Asyut 27.05 31.01 226 I-n-Salah 27.23 2.46 269 Cairo 30.13 31.40 64 Tripoli 32.66 13.15 80 Palmyra 34.55 38.30 408 Aleppo 36.18 37.21 393 Tunis 36.83 10.23 3 Faro 37.01 -7.96 7 Seville 37.41 -5.90 34 Izmir 38.26 27.15 125 Alicante 38.28 -0.55 43 Philadelphia 39.86 -75.23 6 Ankara 39.95 32.88 891 Madrid 40.38 -3.78 690 Istanbul 40.96 28.81 48
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 86
Location Latitude Longitude Altitude Barcelona 41.28 2.06 4
40-60
Rome 41.95 12.50 18 Sofia 42.65 23.38 586 Sapporo 43.06 141.33 26 Varna 43.20 27.91 41 San Sebastian 43.35 -1.80 5 Cannes 43.53 6.95 3 Toulouse 43.63 1.36 152 Florence 43.80 11.20 40 Bologna 44.53 11.30 36 Milan 45.43 9.28 107 Timisoara 45.76 21.25 86 Odessa 46.43 30.76 42 Quebec 46.80 -71.38 70 Graz 47.00 15.43 340 Budapest 47.43 19.26 151 London 51.51 -0.11 5 Moscow 55.75 37.63 156 Edinburgh 55.95 -3.35 41 Petersburg 59.96 30.30 4
Table 4. Locations selected for the present monthly-mean database. Note that 20 locations have been
selected for each of the three latitude bands: 0-20, 20-40 and 40-60 degree N.
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 87
M o nths GNASA Tmax-TuTiempo Tmean-NASA Tmean-TuTiempo Tmin-TuTiempo M o nths GNASA Tmax-TuTiempo Tmean-NASA Tmean-TuTiempo Tmin-TuTiempo
January 6.0 30.4 26.7 27.0 24.3 July 5.9 32.3 26.5 28.9 26.4
F ebruary 6.3 30.4 27.4 27.0 24.6 A ugust 5.9 32.4 26.4 29.0 26.7
M arch 6.5 30.1 27.7 26.8 24.5 September 5.3 32.5 26.1 29.3 26.9
A pril 6.2 31.0 26.8 27.9 25.5 Octo ber 5.0 32.4 25.9 29.0 26.7
M ay 5.7 31.4 26.4 28.4 26.3 N o vember 5.0 31.9 26.0 28.7 26.4
June 5.7 31.5 26.6 28.6 26.1 D ecember 5.4 31.8 26.0 28.2 25.5
January 5.4 30.2 24.4 26.7 23.9 July 5.8 33.1 25.0 29.0 26.1
F ebruary 5.8 29.5 24.8 26.2 23.6 A ugust 5.9 33.6 25.2 29.6 26.7
M arch 6.2 30.4 25.3 26.7 24.0 September 5.8 34.8 25.4 30.3 27.2
A pril 5.8 31.3 25.7 27.8 24.8 Octo ber 5.4 33.2 25.3 29.4 26.3
M ay 5.5 32.7 25.6 28.7 26.1 N o vember 5.0 32.2 25.1 28.3 25.3
June 5.5 33.6 25.2 29.1 26.1 D ecember 5.0 30.8 24.7 27.0 24.2
January 5.7 34.8 23.6 29.1 21.0 July 5.7 33.4 25.1 29.6 24.3
F ebruary 6.3 38.1 25.6 31.3 21.7 A ugust 5.5 33.3 24.9 29.8 25.4
M arch 6.7 37.8 28.5 31.7 21.9 September 5.9 33.4 26.0 28.7 24.2
A pril 7.0 42.1 29.7 36.7 29.8 Octo ber 5.8 35.3 27.7 30.7 25.3
M ay 6.6 40.1 28.3 35.3 27.4 N o vember 5.8 35.5 27.3 30.4 23.6
June 6.2 37.6 26.5 32.5 27.3 D ecember 5.5 33.9 24.4 27.5 19.0
January 4.9 30.3 26.1 25.1 20.8 July 4.7 37.6 29.5 31.9 27.1
F ebruary 5.9 32.4 27.0 26.6 21.6 A ugust 4.8 35.5 29.4 29.6 25.5
M arch 6.6 34.1 27.5 28.5 23.7 September 5.0 35.7 28.5 30.2 25.3
A pril 6.7 36.6 27.0 30.8 26.4 Octo ber 4.4 34.7 27.0 29.7 25.0
M ay 6.1 38.6 26.8 32.1 27.1 N o vember 4.1 30.2 26.1 26.5 23.7
June 5.2 39.3 26.4 32.3 27.8 D ecember 4.2 28.9 25.5 25.1 22.1
January 4.5 33.2 21.3 25.8 20.6 July 7.0 44.5 30.9 36.3 29.8
F ebruary 5.3 34.4 21.7 26.8 21.2 A ugust 6.5 43.6 30.7 35.7 30.2
M arch 6.2 35.7 23.5 27.6 21.5 September 6.2 43.5 30.9 34.9 28.8
A pril 6.9 40.2 26.3 31.9 24.6 Octo ber 5.6 40.8 28.7 31.7 25.6
M ay 7.2 42.6 29.5 33.9 27.8 N o vember 4.6 35.9 25.4 28.4 23.3
June 7.1 45.4 30.9 37.0 31.0 D ecember 4.2 33.0 22.6 25.4 20.5
January 3.6 20.0 18.6 16.0 12.6 July 7.3 38.9 35.1 35.6 32.5
F ebruary 4.4 23.4 19.3 19.2 16.2 A ugust 7.0 39.5 35.2 35.3 32.1
M arch 5.1 24.7 21.5 21.0 17.8 September 6.5 37.2 33.1 33.3 30.3
A pril 6.0 29.9 25.8 25.6 22.0 Octo ber 5.3 33.4 29.8 29.7 26.5
M ay 7.0 36.9 30.8 31.9 28.1 N o vember 4.0 28.7 25.4 25.8 23.3
June 7.7 40.0 33.6 35.3 31.1 D ecember 3.3 22.5 21.1 20.2 17.8
January 3.5 22.0 13.5 13.7 6.2 July 8.0 38.3 30.4 31.7 24.4
F ebruary 4.7 23.6 14.4 15.2 7.1 A ugust 7.5 36.6 30.2 29.9 22.6
M arch 6.0 25.0 18.1 17.2 9.2 September 6.6 35.7 28.3 28.5 20.9
A pril 7.0 32.1 23.2 24.0 15.5 Octo ber 5.2 33.3 24.4 25.6 18.4
M ay 7.5 33.4 27.0 26.3 18.3 N o vember 3.8 25.5 19.5 18.1 11.3
June 8.2 38.2 29.1 30.7 22.3 D ecember 3.1 23.2 15.0 14.9 7.9
January 3.8 21.0 12.0 13.4 6.7 July 7.5 46.1 35.9 38.9 31.6
F ebruary 4.9 24.4 14.9 17.0 9.8 A ugust 7.0 44.9 35.3 37.4 30.2
M arch 5.9 29.5 19.4 22.0 15.0 September 5.8 39.3 31.9 31.8 24.0
A pril 6.6 33.0 24.1 24.6 15.9 Octo ber 4.8 35.9 25.9 28.4 20.6
M ay 7.1 39.5 29.2 31.9 24.0 N o vember 3.9 28.5 19.0 20.7 12.9
June 7.3 44.1 33.9 36.8 28.9 D ecember 3.5 26.0 13.5 16.8 8.6
January 1.7 10.3 4.8 7.4 4.1 July 7.3 30.6 24.1 26.0 21.9
F ebruary 2.5 9.7 5.0 7.0 4.5 A ugust 6.4 29.7 23.9 25.0 20.8
M arch 3.7 11.6 7.6 8.5 5.1 September 5.0 25.1 20.8 21.0 16.8
A pril 4.8 16.4 12.8 12.0 8.3 Octo ber 3.1 21.6 16.0 18.2 14.4
M ay 6.3 23.0 17.8 18.4 13.6 N o vember 1.9 15.8 10.4 12.8 8.6
June 7.2 28.3 22.0 23.4 18.8 D ecember 1.4 13.3 6.1 10.4 6.7
January 2.1 12.7 9.4 8.6 4.6 July 6.8 28.3 22.9 24.7 21.9
F ebruary 3.1 13.7 9.7 9.4 5.4 A ugust 5.8 30.1 23.2 25.6 22.4
M arch 4.3 15.4 11.3 11.8 7.6 September 4.6 25.8 20.8 21.8 18.3
A pril 5.3 17.9 13.0 13.9 10.0 Octo ber 3.1 22.9 17.7 18.6 14.7
M ay 6.0 22.4 16.3 18.3 14.7 N o vember 2.1 19.0 13.2 14.3 10.0
June 6.7 26.4 20.2 22.2 18.6 D ecember 1.8 13.9 10.6 10.1 6.1
January 1.8 3.8 -2.1 -1.2 -6.2 July 6.2 29.2 21.3 22.3 14.4
F ebruary 2.5 5.6 -0.7 0.7 -3.8 A ugust 5.5 28.8 21.1 21.7 14.7
M arch 3.5 11.6 3.6 5.7 0.2 September 4.2 24.0 16.6 17.2 10.9
A pril 4.2 19.1 9.3 11.9 4.8 Octo ber 2.8 17.9 10.7 12.0 6.3
M ay 5.1 24.0 14.7 17.1 9.6 N o vember 1.8 14.3 4.1 7.2 1.0
June 6.0 27.0 18.8 20.0 12.1 D ecember 1.4 7.8 -1.0 2.6 -1.9
January 1.3 1.4 -4.3 -1.4 -5.3 July 4.9 23.0 18.6 19.7 16.8
F ebruary 2.2 0.9 -4.1 -2.2 -6.0 A ugust 4.5 25.3 20.1 21.4 18.3
M arch 3.6 4.9 -0.7 1.5 -2.2 September 3.9 22.2 16.6 17.8 13.1
A pril 4.8 12.5 4.9 7.8 2.6 Octo ber 2.6 16.6 11.1 12.4 7.9
M ay 5.5 19.2 10.0 13.9 9.0 N o vember 1.4 8.3 4.5 5.1 1.4
June 5.5 21.7 14.8 17.5 14.1 D ecember 1.0 2.2 -1.4 -0.7 -4.1
January 1.6 7.4 1.4 2.3 -1.8 July 6.1 30.4 24.2 24.0 17.7
F ebruary 2.4 8.4 2.3 3.8 0.0 A ugust 5.4 28.6 23.8 22.0 15.3
M arch 3.3 11.6 6.4 6.4 1.7 September 4.2 25.1 19.8 18.5 12.6
A pril 4.3 16.2 11.7 10.4 4.6 Octo ber 2.7 19.4 14.5 14.1 9.0
M ay 5.5 22.9 17.2 16.3 9.4 N o vember 1.7 15.6 7.7 9.9 5.6
June 6.0 27.7 21.7 21.1 13.9 D ecember 1.3 9.5 2.5 4.9 1.0
January 1.6 12.3 6.1 9.0 4.6 July 6.3 25.1 21.3 21.3 17.3
F ebruary 2.3 12.5 6.7 9.4 5.0 A ugust 5.5 25.4 21.4 21.6 18.1
M arch 3.7 14.9 9.2 11.6 7.0 September 4.3 22.8 18.7 19.2 15.7
A pril 4.7 16.7 11.2 12.5 8.6 Octo ber 2.8 21.4 15.0 16.6 12.5
M ay 5.7 19.6 15.5 15.8 12.5 N o vember 1.7 17.9 9.9 14.1 9.7
June 6.2 24.1 19.2 20.0 15.9 D ecember 1.3 12.7 7.3 9.6 6.0
C it iesJanuary-June July-D ecember
Cartagena
Caracas
Babanusa
M adras
M akkah
M anama
Asyut
I-n-Salah
Sapporo
Varna
Lat itude
0-20
20-40
40-60
San Sebastian
Istanbul
Barcelona
Sofia
Table 5. Sample of data used in the present work.
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 88
Figure 2a. Regression between mean-daily irradiation ( G ) and temperature (Tmean) for three locations. x-
axis: Tmean, y-axis: G .
R² = 0.98
0
1
2
3
4
5
6
7
‐5 0 5 10 15 20 25
40‐60: Jul‐Dec. MilanR² = 0.98
0
1
2
3
4
5
6
7
‐5 0 5 10 15 20
40‐60: Jan‐Jun. Milan
R² = 0.98
0
1
2
3
4
5
6
7
8
0 5 10 15 20 25
20‐40: Jan‐Jun. AlicanteR² = 0.95
0
1
2
3
4
5
6
7
8
0 5 10 15 20 25 30
20‐40: Jul‐Dec. Alicante
R² = 0.95
0
1
2
3
4
5
6
20.5 21 21.5 22 22.5 23 23.5 24
0‐20: Jul‐ Dec. La EsperanzaR² = 0.86
0
1
2
3
4
5
6
7
20 21 22 23 24 25 26
0‐20: Jan‐Jun. La Esperanza
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 89
Figure 2b Regression between mean-daily irradiation (G ) and temperature (Tmean): all locations. x-
axis: Tmean, y-axis: G .
Even for the sparse irradiation network there is the challenge of careful maintenance
of solarimeters that is required on a day-to-day basis, particularly the due care that is
associated with diffuse radiation measurement. In this respect, a discussion on the lack
of care of shade-ring adjustment and the corresponding errors has been enumerated by
Muneer [6].
As pointed out above solar radiation affects the earth’s weather processes. After
cooling of the land mass during the night sensible heating resulting from irradiation
absorption effects is responsible for ambient temperature variations, so it is possible to
obtain a relationship between temperature and solar radiation. The landmark work in
this respect was carried out by Campbell [7]. Using this argument, Bristow and
Campbell [8] suggested a relationship for global solar radiation as a function of
irradiation and the difference between maximum and minimum temperature.
R² = 0.17
02468
3 8 13 18 23 28 33 38
0‐20: Jan‐Jun R² = 0.04
02468
3 8 13 18 23 28 33
0‐20: Jul‐Dec
R² = 0.79
0
5
10
‐10 0 10 20 30 40
20‐40: Jan‐Jun R² = 0.79
0
5
10
0 10 20 30 40
20‐40: Jul‐Dec
R² = 0.78
0
5
10
‐20 ‐10 0 10 20 30
40‐60: Jan‐Jun R² = 0.86
02468
10
‐20 ‐10 0 10 20 30
40‐60: Jul‐Dec
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 90
Figure 3a. Solar altitudes at noon, irradiation (×10) and Tmean at 10° latitude.
Figure 3b. Solar altitudes at noon, irradiation (×10) and Tmean at 30° latitude.
Figure 3c. Solar altitudes at noon, irradiation (×10) and Tmean at 50° latitude.
Hargreaves and Samani [9] suggested that solar radiation can be estimated from the
above-mentioned difference between maximum and minimum air temperatures, and
introduced an empirical coefficient Kr. Hargreaves [10] recommended the value of Kr to
be 0.16 for interior regions and 0.19 for coastal regions. Annandale et al [11] introduced
a correction factor for empirical coefficient to account for effects of reduced
atmospheric thickness on solar radiation. Allen [12] obtained Kr as a function of the
location altitude to take account of the volumetric heat capacity of the atmosphere (see
Eq. 1).
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 91
Station ME RMSE (%)
Ahmedabad 0.89 6.4
Amritsar 0.92 7.9 Bhopal 0.73 12.7 Hyderabad 0.78 8.6 Jaipur 0.31 16.8 Kodaikanal 0.77 10.1 Nagpur 0.93 4.9 Okha 0.39 13.2 Pune 0.89 6.0 Shillong 0.71 9.9
Present works Sanaa -8.19 19.2 Kufra 0.74 11.5 Budapest 0.92 13.9
Table 6. Comparison between the findings of Bandyopadhyay et al [24] using Eq. 1 and the presently
developed model.
Allen [13] suggested the use of a self-calibrating model to estimate mean monthly
global solar radiation following the work of Hargreaves and Samani [9]. Samani [14]
developed an empirical relationship between Kr and the difference between air
temperature extremes. Meza and Varas [15] evaluated the behaviour of models of Allen
[13] and Bristow and Campbell [8] and inter-compared their results.
Using data from 40 stations covering contrasting climates, Thornton and Running
[1] present a reformulation of the Bristow and Campbell model for daily solar radiation,
based on daily observations of temperature, humidity and precipitation.
Liu and Scott [16], evaluated the accuracy and applicability of several models for
estimating daily value of solar radiation across Australia for different situations, i.e.
using the work of McCaskill [17-18] when only rainfall data were available, the work of
Bristow and Campbell [8], Richardson [19] and Hargreaves and Riley [20] when only
temperature data were available, and the work of De Jong and Stewart [21] and Hunt et
al [22] when data for rainfall and temperature were available.
Zhoy et al [23] validated and compared the above models to predict monthly
average daily global radiation on a horizontal surface based on data from 69
meteorological stations in China. Their work was then extended to select the model with
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 92
the highest accuracy that was then deployed to obtain a geographical distribution of
solar radiation across China.
In their landmark work, Bandyopadhyay et al [24] estimated solar radiation by using
nearly all of the above models that deal with temperature as the sole predictor and
reported on the relative accuracy of those models. The work of Bandyopadhyay et al
[24] was based on data from for 29 stations that were distributed throughout India.
Figure 4. Regression between mean-daily irradiation (G ) and maximum temperature (Tmax): all
locations. x-axis: G , y-axis: Tmax.
R² = 0.18
0
20
40
60
3 4 5 6 7 8
0‐20: Jan‐Jun R² = 0.15
0
20
40
60
3 4 5 6 7 8
0‐20: Jul‐Dec
R² = 0.80
0
20
40
60
0 2 4 6 8 10
20‐40: Jan‐Jun R² = 0.82
0
20
40
60
0 2 4 6 8 10
20‐40: Jul‐Dec
R² = 0.72
‐20
0
20
40
0 2 4 6 8 10
40‐60: Jan‐Jun R² = 0.89
‐10
0
10
20
30
40
0 2 4 6 8 10
40‐60: Jul‐Dec
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 93
Figure 5. Regression between mean-daily irradiation (G ) and minimum temperature (Tmin): all locations.
x-axis: G , y-axis: Tmin.
The methods compared were Hargreaves [10], Annandale [11], Allen [12-13],
Samani [14], and Bristow and Campbell [8]. The estimated solar radiation values were
then compared with measured solar radiation (or solar radiation estimated from
measured sunshine hours with locally calibrated Angstrom coefficients), to check the
suitability of these methods under Indian conditions. The conclusion drawn by
Bandyopadhyay et al [24] was that the original Hargreaves [10] method performed
overall best for Indian locations. The methods due to Allen [12], Samani [14] and
Bristow and Campbell [8] were found to be inferior with the latter being the poorest of
the lot. The Hargreaves [10] may be summarised thus,
G = Kr (Tmax - Tmin)0.5 E (1)
where G is the monthly-mean daily extraterrestrial irradiation (kWh/m2).
R² = 0.04
010203040
3 4 5 6 7 8
0‐20: Jan‐Jun R² = 0.04
010203040
3 4 5 6 7 8
0‐20: Jul‐Dec
R² = 0.68
‐20
0
20
40
0 2 4 6 8 10
20‐40: Jan‐Jun R² = 0.77
‐10
0
10
20
30
40
0 2 4 6 8 10
20‐40: Jul‐Dec
R² = 0.72
‐40
‐20
0
20
40
0 2 4 6 8 10
40‐60: Jan‐Jun R² = 0.76
‐20
‐10
0
10
20
30
0 2 4 6 8 10
40‐60: Jul‐Dec
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 94
4 PRESENTLY PROPOSED MODELS
The present work is developed around the philosophy that for a great many locations
around the world, the only parameter that may be available is the mean ambient
temperature. Furthermore, the model is simple in its constitution. It has been
constructed with the ease of use in mind. Presently, three types of models are proposed
that respectively deal with (i) mean-daily irradiation, (ii) mean-hourly irradiation, and
(iii) hourly temperature. These are presented in the subsequent sections. Figure 1 shows
the information-flow diagram for the present computational scheme.
4.1 Models for mean-daily irradiation
Table 4 presents a list of all locations that have been selected for the present
monthly-mean database. Note that 20 locations have been selected for each of the three
latitude bands: 0-20, 20-40 and 40-60 degree N. The temporal split was created in two
broad categories, i.e. the heating period represented by the January-June months and the
cooling by the July-December period. For the southern hemisphere the split would
obviously be reversed. The present study, being the first of its kind, is being restricted to
the northern hemisphere, and an extension may easily be undertaken for the southern
part of the globe as pointed out above.
Data was extracted from two sources, i.e. the NASA- and the TuTiempo websites.
The former website provides information on G and Tmean. However, to obtain hourly
temperatures, one needs mean-daily Tmin and Tmax. Hence, the latter data were obtained
from the TuTiempo website. A sample of the pooled data is shown in Table 5. The next
step was to obtain regressions between G and Tmean, the logic being that Tmean is
available much more widely in terms of spatial and temporal coverage as pointed out in
Section 1.
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 95
Location Latitude G - Tmean
January-June July-December R2 R2
Accra 5.60 0.80 0.91
0-20
Georgetown 6.50 0.07 0.56 Con Son 8.68 0.71 0.66 Juan Santamaria 9.98 0.51 0.20 Barcelona. V 10.11 0.75 0.69 Cartagena 10.45 0.86 0.93 Caracas 10.60 0.25 0.35 Babanusa 11.33 0.95 0.81 Phnom-Penh 11.55 0.46 0.87 Madras 13.00 0.95 0.77 Bangkok 13.66 0.49 0.94 San Salvador 13.70 0.60 0.98 La Esperanza 14.31 0.86 0.95 Guatemala 14.58 0.46 0.77 Sanaa 15.51 0.99 0.91 Abbs 16.08 0.99 0.85 Timbuktu 16.71 0.99 0.77 Acapulco 16.83 0.60 0.83 Mexico 19.43 0.73 0.86 Akola 20.70 0.79 0.00
Location Latitude G - Tmean
January-June July-December R2 R2
Makkah 21.43 0.97 0.94
20-40
Aswan 23.96 0.96 0.98 Kufra 24.21 0.96 0.98 Riyadh 24.70 0.99 0.99 Manama 26.26 0.98 0.99 Asyut 27.05 0.97 1.00 I-n-Salah 27.23 1.00 0.99 Cairo 30.13 0.98 0.99 Tripoli 32.66 0.98 0.92 Palmyra 34.55 0.99 0.99 Aleppo 36.18 0.99 0.99 Tunis 36.83 0.97 0.96 Faro 37.01 0.99 0.99 Seville 37.41 0.99 0.99 Izmir 38.26 0.98 0.99 Alicante 38.28 0.98 0.95 Philadelphia 39.86 0.99 1.00 Ankara 39.95 0.97 0.99 Madrid 40.38 0.99 0.99 Istanbul 40.96 0.98 0.99
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 96
Location Latitude G - Tmean
January-June July-December R2 R2
Barcelona 41.28 0.96 0.96
40-60
Rome 41.95 0.97 0.97 Sofia 42.65 0.96 0.99 Sapporo 43.06 0.97 0.97 Varna 43.20 0.99 0.99 San Sebastian 43.35 0.99 0.98 Cannes 43.53 0.98 0.97 Toulouse 43.63 0.99 0.99 Florence 43.80 0.99 0.98 Bologna 44.53 0.99 0.98 Milan 45.43 0.98 0.98 Timisoara 45.76 0.99 0.99 Odessa 46.43 0.99 0.99 Quebec 46.80 0.98 1.00 Graz 47.00 0.99 0.99 Budapest 47.43 0.99 0.99 London 51.51 0.99 0.99 Moscow 55.75 0.96 1.00 Edinburgh 55.95 0.99 0.99 Petersburg 59.96 0.98 1.00
Table 7. Regression between mean-daily irradiation (G ) and temperature (Tmean): al locations.
Location Latitude Tmax-G
January-June July-December R2 R2
Accra 5.60 0.95 0.86
0-20
Georgetown 6.50 0.09 0.38 Con Son 8.68 0.47 0.32 Juan Santamaria 9.98 0.23 0.44 Barcelona. V 10.11 0.28 0.17 Cartagena 10.45 0.78 0.13 Caracas 10.60 0.17 0.78 Babanusa 11.33 0.83 0.36 Phnom-Penh 11.55 0.47 0.65 Madras 13.00 0.16 0.77 Bangkok 13.66 0.70 0.16 San Salvador 13.70 0.91 0.68 La Esperanza 14.31 0.51 0.57 Guatemala 14.58 0.44 0.73 Sanaa 15.51 0.92 0.59 Abbs 16.08 0.91 0.86 Timbuktu 16.71 0.96 0.81 Acapulco 16.83 0.46 0.80 Mexico 19.43 0.73 0.78 Akola 20.70 0.77 0.52
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 97
Location Latitude Tmax-G
January-June July-December R2 R2
Makkah 21.43 0.93 1.00
20-40
Aswan 23.96 0.98 0.98 Kufra 24.21 0.94 0.98 Riyadh 24.70 0.99 0.99 Manama 26.26 0.99 0.99 Asyut 27.05 0.98 0.99 I-n-Salah 27.23 0.98 0.99 Cairo 30.13 1.00 0.97 Tripoli 32.66 0.99 0.99 Palmyra 34.55 1.00 0.98 Aleppo 36.18 0.99 0.98 Tunis 36.83 0.99 0.99 Faro 37.01 0.97 0.97 Seville 37.41 0.99 0.95 Izmir 38.26 0.99 0.99 Alicante 38.28 0.99 0.96 Philadelphia 39.86 0.99 0.97 Ankara 39.95 0.98 0.96 Madrid 40.38 0.97 0.97 Istanbul 40.96 1.00 0.99
Location Latitude Tmax-G
January-June July-December R2 R2
Barcelona 41.28 0.99 0.96
40-60
Rome 41.95 0.98 0.96 Sofia 42.65 0.98 0.97 Sapporo 43.06 1.00 0.98 Varna 43.20 1.00 0.98 San Sebastian 43.35 0.98 0.93 Cannes 43.53 0.98 0.99 Toulouse 43.63 0.98 0.98 Florence 43.80 0.97 0.98 Bologna 44.53 0.99 0.98 Milan 45.43 0.99 0.99 Timisoara 45.76 0.96 0.98 Odessa 46.43 0.98 0.98 Quebec 46.80 0.99 0.92 Graz 47.00 0.99 0.98 Budapest 47.43 0.96 0.99 London 51.51 0.98 0.97 Moscow 55.75 1.00 0.97 Edinburgh 55.95 0.97 0.96 Petersburg 59.96 1.00 0.98
Table 8. Regression between mean-daily irradiation (G ) and maximum temperature (Tmax): all locations.
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 98
Location Latitude Tmin-G
January-June July-December
R2 R2 Accra 5.60 0.72 0.85
0-20
Georgetown 6.50 0.63 0.21 Con Son 8.68 0.64 0.07 Juan Santamaria 9.98 0.69 0.90 Barcelona. V 10.11 0.17 0.46 Cartagena 10.45 0.69 0.15 Caracas 10.60 0.18 0.83 Babanusa 11.33 0.39 0.18 Phnom-Penh 11.55 0.31 0.86 Madras 13.00 0.11 0.55 Bangkok 13.66 0.20 0.01 San Salvador 13.70 0.22 0.75 La Esperanza 14.31 0.28 0.57 Guatemala 14.58 0.09 0.90 Sanaa 15.51 0.96 0.55 Abbs 16.08 0.90 0.81 Timbuktu 16.71 0.88 0.97 Acapulco 16.83 0.26 0.66 Mexico 19.43 0.34 0.66 Akola 20.70 0.24 0.31
Location Latitude Tmin-G
January-June July-December R2 R2
Makkah 21.43 0.85 0.97
20-40
Aswan 23.96 0.99 0.99 Kufra 24.21 0.95 1.00 Riyadh 24.7 0.99 0.98 Manama 26.26 0.99 0.98 Asyut 27.05 0.99 0.99 I-n-Salah 27.23 0.94 0.99 Cairo 30.13 0.99 0.98 Tripoli 32.66 0.99 0.99 Palmyra 34.55 1.00 0.98 Aleppo 36.18 0.99 0.98 Tunis 36.83 0.99 1.00 Faro 37.01 0.95 0.98 Seville 37.41 0.96 0.98 Izmir 38.26 0.98 0.99 Alicante 38.28 0.99 0.99 Philadelphia 39.86 1.00 0.94 Ankara 39.95 0.98 0.96 Madrid 40.38 0.97 0.98 Istanbul 40.96 1.00 0.98
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 99
Location Latitude Tmin-G
January-June July-December R2 R2
Barcelona 41.28 0.99 0.98
40-60
Rome 41.95 0.99 0.98 Sofia 42.65 0.99 1.00 Sapporo 43.06 0.96 0.98 Varna 43.2 0.99 0.97 San Sebastian 43.35 0.99 0.98 Cannes 43.53 0.98 0.97 Toulouse 43.63 1.00 0.94 Florence 43.8 0.95 0.98 Bologna 44.53 0.98 0.94 Milan 45.43 0.98 0.97 Timisoara 45.76 0.99 0.98 Odessa 46.43 0.97 0.96 Quebec 46.8 0.99 0.94 Graz 47 1.00 0.98 Budapest 47.43 0.98 0.98 London 51.51 0.98 0.94 Moscow 55.75 0.97 0.92 Edinburgh 55.95 0.98 0.97 Petersburg 59.96 1.00 0.93
Table 9. Regression between mean-daily irradiation (G ) and minimum temperature (Tmin): all locations.
Model R2 Model R2
0‐20 0.17 0.04
20‐40 0.79 0.79
40‐60 0.78 0.86
Latitude RangeJuly‐DecemberJanuary‐June
201.023.052.7 meanmean TTG ∗+∗−=
2001.0232.0636.1 meanmean TTG ∗−∗+=
2005.0123.0211.2 meanmean TTG ∗+∗+=
2003.0102.0837.5 meanmean TTG ∗+∗−=
2001.0175.0511.0 meanmean TTG ∗+∗+=
2005.0078.0955.0 meanmean TTG ∗+∗+=
Model R2 Model R2
0‐20 0.18 0.15
20‐40 0.8 0.82
40‐60 0.72 0.89
Latitude RangeJuly‐DecemberJanuary‐June
2max 45.181.1461.67 GGT ∗+∗−=
2max 18.083.219.4 GGT ∗+∗+=
2max 04.066.447.2 GGT ∗−∗+−=
2max 06.139.970.50 GGT ∗+∗−=
2max 50.080.815.0 GGT ∗−∗+=
2max 80.030.1006.3 GGT ∗−∗+−=
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 100
Model R2 Model R2
0‐20 0.04 0.04
20‐40 0.68 0.77
40‐60 0.72 0.76
Latitude RangeJanuary‐June July‐December
2min 29.117.1433.59 GGT ∗+∗−=
2min 24.145.1248.52 GGT ∗+∗−=
2min 25.066.189.5 GGT ∗+∗+−=
2min 39.036.089.2 GGT ∗+∗−=
2min 40.017.752.6 GGT ∗−∗+−=
2min 40.019.645.5 GGT ∗−∗+−=
Table 10. Models for mean-daily irradiation (G ) based on mean temperature (Tmean), mean- maximum
temperature (Tmax) based on daily irradiation ( G ) and mean-minimum temperature (Tmin) based on daily
irradiation ( G ): all locations.
Figure 6. Time of occurrence of the (a) minimum and (b) maximum temperature.
Figures 2a and b respectively, show regressions between G and Tmean for individual
and grouped locations. Two points are worth mentioning. First, for any given location
there is a strong correlation between the two parameters under discussion and, secondly,
0
5
10
15
20
7 9 11 13 15 17
Max. Temperature
0
5
10
15
20
7 9 11 13 15 17
Max. Temperature
0
5
10
15
20
7 9 11 13 15 17
05
1015202530
0.00 5.00 10.00 15.00 20.00
Min. Temperature
05
1015202530
0.00 5.00 10.00 15.00 20.00
Min. Temperature
0
5
10
15
20
25
30
0.00 5.00 10.00 15.00 20.00
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 101
the high values of R2 are restricted to latitudes above 20º The much more weaker
correlations for the near-equatorial band has also been reported by Swartman and
Ogunlade [25] and Bandyopadhyay et al [24]. The former study has, respectively,
attempted regressions between G and precipitable water and between G and daily
temperature range. However, the important point to note is that the Tmean itself or indeed
the daily temperature range is dictated by the much more uniform movement of the sun
within the tropics. This point is demonstrated via Figure 3 that shows the narrow range
of noon solar altitude for the 0-20º latitude band. Note that for the other two latitude
bands 20º to 40º and the 40º to 60º, there is a close concordance between Tmean and
G with noon altitude.
The present sets of models were also compared in terms of their accuracy to those
reported by Bandyopadhyay et al [24]. The latter team has used the following statistical
parameters to evaluate the model’s accuracy. Equations for Modelling Efficiency (ME)
and root-mean square error (RMSE), used by the latter work of reference, are provided
in the following equations.
( ) ( )
( )∑
∑ ∑
=
= =
−
−−−= n
ioio
n
i
n
iioipoio
xx
xxxxME
1
2,
1 1
2,,
2
,
(2)
( )100
/(%)
5.0
1
2,,
×⎟⎠
⎞⎜⎝
⎛−
=∑=
o
n
iioip
x
nxxRMSE (3)
where iox , is the measure variable, ox the average of the measured variable and ipx , the
computed variable.
Table 6 compares the findings of Bandyopadhyay et al [24] using Equation. 1 and
the presently developed model.
Refer to Figure 1 that shows the presently-proposed computational chain for
obtaining hourly temperatures. The next step is to obtain regression models between
Tmax andG , and between Tmin andG . Figures 4 and 5 respectively present those
findings.
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 102
Figure 7 Inter-relationship between daily maximum, minimum and mean temperature for three locations.
Once again the strong correlation between the variables under discussion is
apparent. Furthermore, we note that, as found above, a much weaker correlation exists
for the near-equatorial band. Tables 7-9 provide the R2 values for the regressions under
discussion, for all locations. The above discussion is thus further reinforced. It is
therefore recommended that the presently proposed relationship be used, with
confidence, for locations above 20º N latitude.
Table 10 (a-c) provides the proposed models that relate G to Tmean, Tmax toG , and
Tmin toG . Note that there is a weaker correlation between Tmin and G . This may be
explained as follows. Whereas during the daytime the sun’s irradiation is the strongest
contributor to the rise of temperature, after sunset, during nocturnal hours a number of
factors determine the rate of heat loss from the landmass, i.e. direction and speed of
wind, and duration and amount of precipitation (rain or snow). Thus a weaker
correlation exists between Tmin and G . This point is demonstrated in a greater detail via
Figure 6(a-b). The time of occurrence for Tmax is much more well defined than Tmin. The
time of occurrence for Tmax and Tmin is important information as it enables one to obtain
0.0
5.0
10.0
15.0
20.0
25.0
30.0
1 2 3 4 5 6 7 8 9 10 11 12
0-20. La Esperanza
Tmax
Tmin
Tmean
0.0
5.0
10.0
15.0
20.0
25.0
30.0
35.0
1 2 3 4 5 6 7 8 9 10 11 12
20-40. Alicante
Tmax
Tmin
Tmean
‐5
0
5
10
15
20
25
30
35
1 2 3 4 5 6 7 8 9 10 11 12
40-60. Milan
Tmax
Tmin
Tmean
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 103
hourly temperatures for the 24-h period. American Society of Heating, Refrigerating
and Air-Conditioning Engineers (ASHRAE) [26] has provided the latter procedure and
that will be the subject of discussion in Section 4.3.
Cities Latitude
Tcomputed-Tobserved
January-June July-December
Slope R2 Slope R2
Cartagena 0-20 1.16 0.97 0.99 0.95 I-n-Salah 20-40 1.06 1.00 1.03 1.00 Sofia 40-60 1.06 1.00 1.07 1.00
Table 11 Regression between daily-mean minimum temperature: computed and measured values for three
locations.
To provide a better procedure to obtain Tmin an attempt was made to relate the latter
parameter to Tmean and Tmax. Figure 7 shows plots for three international locations. The
point to note here is that Tmean seems to be a close average of Tmin and Tmax On the latter
basis, Tmin may thus be obtained as follows:
Tmin = 2 Tmean - Tmax (4)
Using Equation 4, Tmin was computed for three of the present locations and then
compared with its measured value. Table 11 shows that using this procedure, Tmin may
be obtained with satisfactory accuracy.
Table 12 shows the correspondence between the Tmean values from the two sources –
NASA and TuTiempo. Once again we note that there is a much weaker correspondence
for locations near the equatorial belt. The primary reason for this may be attributed to
the poor quality of measured temperature records for developing countries. A number of
studies have alluded to this point. The correspondence at latitudes north of 20º seems to
be quite strong though and hence the Tmean data may be used inter-changeably.
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 104
Location Latitude Tmean-TuTiempo-Tmean-NASA
Slope R2
Accra 5.60 0.61 0.90
0-20
Georgetown 6.50 0.39 0.47 Con Son 8.68 0.51 0.79 Juan Santamaria 9.98 0.90 0.36 Barcelona. V 10.11 0.48 0.33 Cartagena 10.45 -0.52 0.65 Caracas 10.60 0.15 0.27 Babanusa 11.33 0.56 0.65 Phnom-Penh 11.55 0.35 0.35 Madras 13.00 0.63 0.90 Bangkok 13.66 0.59 0.49 San Salvador 13.70 0.65 0.51 La Esperanza 14.31 0.34 0.30 Guatemala 14.58 0.43 0.31 Sanaa 15.51 0.78 0.74 Abbs 16.08 0.73 0.69 Timbuktu 16.71 0.76 0.89 Acapulco 16.83 0.23 0.31 Mexico 19.43 1.09 0.91 Akola 20.70 0.88 0.91
Location Latitude Tmean-TuTiempo-Tmean-NASA
Slope R2
Makkah 21.43 1.09 0.94
20-40
Aswan 23.96 1.06 0.98 Kufra 24.21 0.97 0.97 Riyadh 24.7 1.07 0.99 Manama 26.26 1.12 0.99 Asyut 27.05 0.94 0.98 I-n-Salah 27.23 0.99 0.99 Cairo 30.13 0.93 0.97 Tripoli 32.66 0.80 0.96 Palmyra 34.55 1.01 0.98 Aleppo 36.18 0.95 0.98 Tunis 36.83 0.89 0.98 Faro 37.01 1.00 0.97 Seville 37.41 0.99 0.98 Izmir 38.26 1.03 0.99 Alicante 38.28 0.91 0.97 Philadelphia 39.86 0.98 0.98 Ankara 39.95 0.96 0.97 Madrid 40.38 1.01 0.99 Istanbul 40.96 0.92 0.97
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 105
Location Latitude Tmean-TuTiempo-Tmean-NASA
Slope R2
Barcelona 41.28 1.17 0.99
40-60
Rome 41.95 1.20 0.95 Sofia 42.65 1.05 0.99 Sapporo 43.06 0.98 0.99 Varna 43.20 1.13 0.99 San Sebastian 43.35 1.21 0.98 Cannes 43.53 1.08 0.98 Toulouse 43.63 1.07 0.99 Florence 43.80 0.92 0.98 Bologna 44.53 0.85 0.98 Milan 45.43 1.12 0.99 Timisoara 45.76 1.01 0.98 Odessa 46.43 1.06 0.99 Quebec 46.80 1.06 0.97 Graz 47.00 1.03 0.98 Budapest 47.43 0.98 0.98 London 51.51 0.91 0.95 Moscow 55.75 1.14 0.98 Edinburgh 55.95 0.97 0.95 Petersburg 59.96 1.09 0.98
Table 12. Regression between monthly-mean temperature (Tmean) data from the two sources -
NASA and TUTIEMPO.
4.2 Models for mean-hourly irradiation
To provide a model to decompose averaged daily to averaged hourly values, Liu and
Jordan [27] built on an earlier work by Whillier [28] to develop a set of regression
curves, which represent the ratio of hourly to daily global solar irradiation at a series of
time intervals from solar noon. This approach was validated by Collares-Pereira and
Rabl [29] who obtained the following equation using a least-square fit as follows:
(5)
where rG is the ratio of hourly to daily radiation, a and b the site-specific coefficients, ω
the hour angle (º) ans ωs the sunset hour angle (º).
In Equation (5), a = 0.409 + 0.5016 sin (ωs-1.047), b = 0.6609 - 0.4767sin (ωs-
1.047).
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 106
Figure 8. Ratio of hourly to daily global irradiation for different hours of the day versus sunset hour
angle.
Hour Z Hour Z 1 0.12 13 0.95
2 0.08 14 1.00 3 0.05 15 1.00 4 0.02 16 0.94 5 0.00 17 0.86 6 0.02 18 0.76 7 0.09 19 0.61 8 0.26 20 0.50 9 0.45 21 0.41
10 0.62 22 0.32 11 0.77 23 0.25 12 0.87 24 0.18
Table 13. ASHRAE model for diurnal temperature swing.
Location Year Slope R2 MBE
(°C) RMSE
(°C) Abu Dhabi 1997 0.99 0.77 -0.1 3.7 London 1990 0.97 0.93 -0.4 1.6 Edinburgh 1990 0.97 0.86 -0.3 1.7
Table 14. Performance of ASHRAE model for three international locations.
All of the above studies were undertaken using data from US locations. However,
the above model’s validity was also checked for Indian locations by Hawas and Muneer
[30] who compared measurements from 13 Indian locations and found a general
agreement for the rG model. In an extended study, Tham et al [31] used long-term
hourly irradiation data from 16 locations in UK to evaluate the above rG model. The
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 107
findings of the above two studies, for India and the UK, are summarised Figure 8 which
shows a remarkable concordance between the rG model and data from the latter two
countries. Tham et al. has also reported on the statistical evaluation of the rG model. The
errors in computing hourly from the mean-daily irradiation, for mainland UK locations,
were found to be normally distributed around zero, with 39% points lying in the ± 10%
range, and 67% of the data in the ± 20% range.
4.3 Models for hourly temperatura
Accurate hourly data are required in very many applications. To meet this need, a
simple model to estimate hourly temperature from daily records has been provided by
the ASHRAE [32]. A compute program to decompose daily to hourly temperature has
been provided by Muneer et al. [33]. That code is also available in Muneer’s book [6].
The daily maximum temperature that is achieved at a given location is dependent on the
prevailing solar radiation, cloud-cover and wind profile. The earliest available models
suggest a sinusoidal profile between the daily maximum and minimum temperatures.
However, more recent work of Hedrick [34] and Thevenard [35], ASHRAE [26] has
further updated the latter model. Table 13 gives the hourly temperature profile,
expressed in terms of a presently defined Z-parameter (ratio of hourly temperature
elevation to daily range {=Th-Tmin)/(Tmax-Tmin)}, dimensionless). ASHRAE [26] has
suggested that this profile is a representative of both dry-bulb and wet-bulb temperature
variation on typical design days. The tabulated information provided by ASHRAE [26]
has been cross-checked using averaged hourly data from 58 Turkish locations [36] and
hourly data from three international locations, i.e. Edinburgh, London and Abu Dhabi.
Table 14 includes that information.
Data from the above three international locations were then used to evaluate the
ASHRAE model. Figure 9 and Table 14 present the evaluation that used four statistical
indicators. These indicators are the slope of the best-fit regression line between the
computed and measured values, coefficient of determination value (R2) for the above
best-fit line, mean bias error (MBE) and (RMSE).
The slope of the best-fit line shows that the model performs well for all locations in
this study. The R2 indicator for Abu Dhabi showed that the model slightly under-
performs in terms of data scatter. For the remaining stations, the R2 values lie in the
range 0.86-0.93, showing that the model performs well. The highest value of MBE is -
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 108
0.4 °C for Edinburgh and the lowest is -0.1°C at Abu Dhabi. This shows a good
agreement with the slope of the best-fit line where Abu Dhabi has the best value near to
the desire value of 1. The RMSE value for Abu Dhabi is the highest with the value of
3.7°C and the lowest value of 1.6 °C was found for London.
Furthermore, a comparison between the ASHRAE temperature model and the mean-
hourly temperature record for locations within the UK and Turkey was carried out. It is
evident that the UK temperature trend very closely follows the ASHRAE model. A
slight upward shift of temperatures was observed for Turkey for the ante meridiem
hours. Figure 10 shows that comparison.
Figure 9. Presently obtained, yearly-averaged Z-parameter for three international locations.
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 109
Figure 10. Comparison of mean-hourly temperature trend.
5 CONCLUSIONS
World-wide there is many more temperature measuring meteorological stations that
those that measure solar radiation. Presently, a case has been made for the development
of temperature-based mathematical models to obtain mean-daily irradiation. In contrast
to the classical models that use daily temperature range, use was made of mean-daily
temperature as the basic regressor. The accuracy of predicting mean-daily irradiation
was evaluated using two statistical indicators – ME and RMSE. The latter have been
defined via Equations (2 and 3). It was found that the ME lay between 0.7 to -8.2 and
the RMSE between 12 and 34%.
Furthermore, a procedure to decompose daily to hourly temperatures was also
evaluated. It was found that the procedure, although originally developed using data
from North American locations, produces reliable estimates of hourly temperature with
a low MBE range that varied from -0.1 to -0.4°C and the RMSE range that varied
between 1.6°C and 3.7°C for three international locations. A review of models that
decompose mean-daily irradiation to hourly data sets was also presented. It was found
that this latter variable may be obtained with an accuracy figure of ± 20W/m2 for over
50% of the time.
Finally, there are large body of existing data on the above parameters measured
across the world in recent years. These data may be used or further validation of the
proposed model for different geographic areas, climatic zones and seasons. The
presently proposed statistical metrics may then be used to evaluate further accuracy
enhancement that may thus be achieved.
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 110
6 ACKNOWLEDGEMENTS
The lead author (EJG) is thankful to the Spanish Ministry of Education and to
Granada University for providing financial assistance for this work. The authors also
wish to thank Edinburgh Napier University, Transport Research Institute (TRI), for
providing all necessary facilities.
REFERENCES
[1] Thornton PE, Running SW. An improved algorithm for estimating incident daily
solar radiation from measurements of temperature, humidity, and precipitation. Agric
Meteorol 1999;93:211–28.
[2] Rivisgton M, Matthews KB, Bunchan K. A comparison of methods for
providing solar radiation data to crop models and decision support systems. In:
Proceedings of the Integrated assessment and decision support, 1st Biennial Meeting of
International Environmental Modelling and Software Society, Vol. 3, June 24–27 2002.
193–8.
[3] Angstrom A. Solar and terrestrial radiation. QJR Meteorol Soc 1924;50:121–5.
[4] Muneer T, Saluja G. A brief review of models for computing solar radiation on
inclined surfaces. Energy Convers Manage 1985;25:443.
[5] Colliver D. In Parker B.F. (ed.) Solar Energy in Agriculture. Energy in World
Agriculture. Elsevier, 1991.
[6] Muneer T. Solar Radiation and Daylight Models, 2nd edn. Elsevier, 2004.
[7] Campbell G. An Introduction to Environmental Biophysics. Springer, 1977.
[8] Bristow K, Campbell G. On the relationship between incoming solar radiation
and daily maximum and minimum temperature. Agric Meteorol 1984;31:159–66.
[9] Hargreaves G, Samani Z. Estimating potential evapotraspiration. J Irrig Drain
Eng ASCE 1982;180:225–30.
[10] Hargreaves G. Simplified coefficients for estimating monthly solar radiation in
North America and Europe. Dept. Paper, Department of Biology and Irrigation
Engineering, Utah State University. 1994.
[11] Annandale JG, Jovanovic NZ, Benade N, et al. Software for missing data error
analysis of Penman–Monteith reference evapotraspiration. Irrig Sci 2002;21:57–67.
E J Gago et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 111
[12] Allen R. Evaluation of procedures for estimating mean monthly solar radiation
from air temperature. Report. Food and Agriculture Organization of the United Nations
(FAO). 1995.
[13] Allen R. Self-calibrating method for estimating solar radiation from air
temperature. J Hydrol Eng 1997;2:56–67.
[14] Samani Z. Estimating solar radiation and evapotraspiration using minimum
climatological data. J Irrig Drain Eng ASCE 2000;126:265–7.
[15] Meza F, Varas E. Estimation of mean monthly solar radiation as a function of
temperature. Agric Meteorol 2000;100:231–41.
[16] Liu DL, Scott BJ. Estimation of solar radiation in Australia from rainfall and
temperature observations. Agric Meteorol 2001;106:41–59.
[17] McCaskill MR. An efficient method for generation of full climatological
records from daily rainfall. Aust J Agrc Res 1990;41:595–602.
[18] McCaskill MR. Prediction of solar radiation from rain information using
regionally stable coefficients. Agric Meteorol 1990;51:247–55.
[19] Richardson CW. Weather simulation for crop management models. Trans
ASEA 1985;28:1602–6.
[20] Hargreaves G, Riley J. Irrigation water requirement for Senegal River Basin. J
Irrig Drain Eng ASCE 1985;111:265–75.
[21] De Jong R, Stewart DW. Estimating global solar radiation from common
meteorological observations in Western Canada. Can J Plant Sci 1993;73:509–18.
[22] Hunt LA, Kuchar L, Swanton CJ. Estimation of solar radiation for use in crop
modelling. Agric Meteorol 1998;91:293–300.
[23] Zhoy J, Wu Y, Yan G. General formula for estimation of monthly average daily
global radiation in China. Energy Convers Manage 2005;46:257–68.
[24] Bandyopadhyay A, Bhadra A, Raghuwanshi NS, et al. Estimation of monthly
solar radiation from measured air temperature extremes. Agric Meteorol
2008;148:1707–18.
[25] Swartman R, Ogunlade O. Solar radiation estimates from common parameters.
In Proceedings of Solar Energy Conference, Vol. 4, 1967. 20–2.
[26] ASHRAE Handbook of Fundamentals. American Society of Heating,
Refrigerating and Air-Conditioning Engineers, 2009.
[27] Liu B, Jordan R. The inter-relationship and characteristic distribution of direct,
diffuse and total solar radiation. Solar Energy 1960;4:1.
Capitulo 3: Modelos de descomposición para la irradiancia horaria y la temperatura
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 112
[28] Whillier A. The determination of hourly values of total radiation from daily
summations. Archiv Meteorol Geophys Bioclimatol 1956;7(Series B):197.
[29] Collares-Pereira M, Rabl A. The average distribution of solar radiation
correlations between diffuse and hemispherical and between daily and hourly insolation
values. Solar Energy 1979;22:155.
[30] Hawas M, Muneer T. Study of diffuse and global radiation characteristics in
India. Energy Convers Manage 1984;24:143.
[31] Tham Y, Muneer T, Davison B. Estimation of hourly averaged solar
irradiation: evaluation of models. Build Serv Eng Res Technol 2010;31:9.
[32] ASHRAE Handbook of Fundamentals. American Society of Heating,
Refrigerating and Air-Conditioning Engineers, 1997.
[33] Muneer T, Abodahab N, Weir G, et al. Windows in Buildings. Elsevier, 2000.
[34] Hedrick R. Generation of hourly design-day weather data (RP-1363). ASHRAE
Research Project, Final Report. 2009.
[35] Thevenard D. Updating the ASHRAE climatic data for design and standards
(RP-1453). ASHRAE Research Project, Final Report. 2009.
[36] Coskun C, Oktay Z, Dincer I. A novel approach to cooling degree-hour
calculation: an application for 58 cities in Turkey. In 5th International Ege Energy
Symposium, 27–30 June 2010, Pamukkale University.
Capítulo IV: Capacidad Energética Solar Fotovoltaica
J. Ordóñez et al., 2010
The use of photovoltaic solar energy as an energy source in the residential housing sector 113
ANALYSIS OF THE PHOTOVOLTAIC SOLAR
ENERGY CAPACITY OF RESIDENTIAL ROOFTOPS IN
ANDALUSIA (SPAIN) J. Ordóñez, E. Jadraque, J. Alegre, G. Martínez
Department of Civil Engineering, University of Granada, Spain
Abstract
Fossil fuel energy resources are becoming increasingly scarce. Given the negative
environmental impacts (e.g. greenhouse gas emissions) that accompany their use, it is
hardly surprising that the development of renewable energies has become a major
priority in the world today. Andalusia, with a mean solar radiation of 4.75 kWh/m2 per
day and a surface area of 87,597 km2, is the region in Europe with the highest solar
energy potential. This research study determined the solar energy potential in Andalusia
for grid-connected photovoltaic systems installed on residential rooftops.
Amethodology was developed for this purpose,which first involved a description of
building characteristics, followed by the calculation of the useful roof surface area
where photovoltaic arrays could be installed. In the next phase of the study, the mean
solar irradiation characteristics were defined as well as the technical parameters of the
photovoltaic systems. All of these factors allowed us to estimate the amount of
electricity that could be potentially generated per year by solar panels. © 2010 Published by
Elsevier Ltd.
Keywords: Renewable energy, Solar energy, Edification, Photovoltaic solar energy
1364-0321/$ – see front matter © 2010 Published by Elsevier Ltd.
doi:10.1016/j.rser.2010.01.001
Capitulo 4: Capacidad energética de las cubiertas
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 114
1 INTRODUCTION
The analysis of the current energy production model and its comparison with the
evolution of energy consumption clearly reflects the limited nature of conventional
energy resources as well as the progressive deterioration of the environment, stemming
from this kind of energy model [1, 2]. The dramatic increase in energy consumption in
the European Union in recent years has brought with it a dependence on external energy
sources that could reach 80% in 2020 if countermeasures are not rapidly taken.
Fortunately, there is now a growing social awareness of the negative environmental
impacts of fossil fuel energy as well as the environmental problems related to the use of
nuclear energy. This new social conscience of environmental problems and possible
solutions will have a direct effect on how energy challenges are met in the future. This
will doubtlessly signify a reduction in fossil fuel energy consumption as well as an
increase in the production of renewable energies or energies generated from natural
resources. This new energy model should be based on energy sources that are
sustainable from an environmental perspective and safe with little or no risk of
accidents. Such sources should also be in large supply so as to ensure their long-term
availability [3]. The increased use and advancement of renewable energies offer a viable
solution for environmental problems caused by other energy sources [2]. For this
reason, current European policies are focused on the development and use of renewable
energy [6]. The residential sector, whose energy consumption in Europe is 30.2% of the
total, is clearly in a position to initiate actions conducive to energy sustainability [3].
One possible solution, which is now an essential component of the energy policies of
most countries, is the production of solar energy by means of building integrated
photovoltaic systems, connected to the grid [4, 5]. The region of Andalusia is located in
southern Spain, and has a total surface area of 87,597 km2. With an average solar
radiation of 4.75 kWh/m2 per day [6, 7], it is the region in Europe with the highest solar
energy potential for the production of this type of renewable energy [8, 9]. Furthermore,
the large volume of residential building construction in recent years and the deficit of
conventional energy sources justify any initiatives conducive to the construction of self-
sustainable residential buildings that are capable of producing their own energy for
illumination, HVAC, electrical appliances, etc. The installation of building-integrated
photovoltaic systems is a viable option for the achievement of energy sustainability. The
J. Ordóñez et al., 2010
The use of photovoltaic solar energy as an energy source in the residential housing sector 115
objective of this research study was to calculate the energy capacity of grid-connected
photovoltaic arrays that could be mounted on building roofs. For this purpose, we used
statistical construction data as well as digital urban maps obtained from Google EarthTM
to measure the useful roof surface area of a representative sample of buildings of the
total population. Among the factors considered were: building type, orientation, roof tilt
angle, location, shading, as well as other competing uses, such as air conditioning and
heating installations, elevator shafts, roof terraces, or penthouses [10]. We were thus
able to estimate the electrical energy potential by calculating the useful roof surface area
of the buildings and by dimensioning the type of photovoltaic solar array to be mounted
on the roofs. This study compares the technical potential of rooftop photovoltaic solar
energy in Andalusia with the total energy consumption in the residential sector. The
final section of the article presents the conclusions that can be derived from this study.
2 CONTEXT AND JUSTIFICATION
In recent years, an enormous effort has been made to develop models that explain
how energy consumption is distributed in residential dwellings. Such models have
analyzed this problem with a wide variety of different methods that range from
econometric analyses to individual studies of residential building types, which were
then extrapolated to the total set of buildings [11]. Moreover, many research studies
have tried to estimate the solar energy potential in relation to the total roof surface area
as well as the total surface area of the geographic area targeted in the study [4]. In this
sense, Spain is in a position to play a key role in the implementation of renewable
energy technology in Europe [6] due to its surface area, investments in large solar
energy plants, and numerous research projects funded by public and private organisms.
The objective of this research study was to calculate the solar energy potential of
building rooftops, based on the dimensioning and design of photovoltaic arrays that
could be mounted on these surfaces. For this purpose, we developed a model that was
subsequently applied and validated in the geographic region of Andalusia (Spain).
3 METHODOLOGY
Our aim was to estimate the energy capacity of photovoltaic solar energy systems
that could be installed on the rooftops of residential buildings in Andalusia. In order to
achieve this research goal, we carried out the following actions (see Fig. 1):
Capitulo 4: Capacidad energética de las cubiertas
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 116
• The building sector was described in terms of construction statistics published
by the Spanish Ministry of Development. This analysis provided us with the gross roof
surface area for each building type. This information was obtained for each of the eight
provinces in the region of Andalusia.
• We selected a representative sample of buildings, and statistically analyzed their
roof surface area. This allowed us to contrast the results of this sample with those
obtained in the previous analysis.
• The geometric characteristics of three building types (i.e. detached and semi-
detached houses, town houses and row houses, and high-rise buildings) were defined.
This made it possible to obtain the useful roof surface where photovoltaic arrays could
be installed.
• The photovoltaic solar array was then designed, and the energy generation
potential was calculated for each of the eight provinces in Andalusia.
Characterization
of thebuilding sector
Nº of buildings.Building types
Total surface area:flat roofs, piched
roofsTs
Macrostatistics
Cofidence level95 %
Analysis of the useful roof surface
area for photovoltaicarrays
Mean useful surface area and
dimensions
Building sample.95 % confidence
level
Installationdesign
Energy generate perm2 of useful roofsurface area: Eg
Coefficient 1: Us/Ts
Total useful roofsurface area
Tus = Coeff.1 x Ts
Energy capacityof residentialbuilding roofsEc = Eg x Tus
Fig. 1. Methodology.
The following sections describe the research phases in which the building types
were characterized and the rooftop surface area obtained.
3.1 Building characterization. Total roof surface area
The statistical data used for this study refers to 2000–2007, and was compiled by the
Spanish Government, more specifically, the General Directorate of Economic
Programming, a subsection of the Secretary of State for Infrastructure, which is part of
J. Ordóñez et al., 2010
The use of photovoltaic solar energy as an energy source in the residential housing sector 117
the Ministry of Development. This information was obtained by means of a
datacollection questionnaire, based on building licenses granted by city governments.
These data are collected on a monthly basis by the Ministry of Development for all of
Spain. The ‘‘no response’’ answer in a certain number of questionnaires was dealt with
by stratifying city governments, according to province. This was done by calculating the
expansion coefficients, based on the population of the municipalities and the number of
licenses granted. The formula used was the following:
where Cij is the elevation coefficient of stratum i in province j. Pij is the population of
the municipalities of stratum i in province j. pij is the population of the municipalities of
stratum i in province j, who have answered the questionnaire. Lij is the number of
licenses granted in stratum i of province j. lij is the number of licenses with a
questionnaire of stratum i in province j.
This expansion coefficient used the first factor Pij/pij to correct the no response
answer and Lij/lij to correct the non-completion or the questionnaire. The final results
were obtained by adding the questionnaires of each stratum-province and multiplying
this figure by the expansion coefficient. The size of the sample, namely, the minimum
number of municipalities received from each stratum (n), depended on the total number
of municipalities (N), the desired confidence level (K), the variability of the building
licenses granted (s), and the absolute error assumed for these licenses (e). The formula
used was the following:
Our study targeted all buildings with a residential function. Buildings were
classified in three categories: (1) detached and/or semi-detached houses; (2) town
houses or row houses; (3) high- rise apartment buildings. Based on statistical data
collected for 2000–2007, we obtained the mean roof surface area for each building type
(see example in Table 1).
Cij = Pij/pij·Lij/lij
n=N2K2S2/ (e2+NK2S2)
Capitulo 4: Capacidad energética de las cubiertas
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 118
BUILDING TYPOLOGY. 2007
Province Nº. Buildings (Unit) Total Roof Surface Area (m2)
Mean Roof Surface Area/Building (m2/Unit)
0-2 3 4-5 6 or more 0-2 3 4-5 6 or more 0-2 3 4-5 6 or more Almería 1,540 774 351 292 220,873.0 252,667.4 180,916.9 80,536.9 143.4 326.4 515.4 275.8Cádiz 482 157 53 0 78,337.2 74,518.9 32,499.1 0.0 162.4 474.6 613.2 0.0Córdoba 1,261 366 89 0 273,456.0 84,565.6 31,204.9 0.0 216.9 231.1 350.6 0.0Granada 2,606 2,012 462 41 493,417.1 312,823.9 191,840.1 14,551.8 189.4 155.5 415.2 354.9Huelva 979 145 65 22 259,241.0 41,873.2 29,982.0 14,213.1 264.8 288.8 461.3 646.1Jaén 286 656 386 45 36,416.2 143,946.1 132,386.3 3,315.5 127.5 219.4 343.0 73.7Málaga 1,468 1,047 347 92 201,822.7 385,129.4 204,186.3 47,791.4 137.5 367.8 588.4 519.5Seville 1,730 641 78 47 225,315.7 98,788.6 26,239.0 43,623.3 130.3 154.1 336.4 928.2Total 10,352 5,798 1,831 539 1,788,878.9 1,394,313.1 829,254.7 204,032.1 171.5 277.2 452.9 349.8Total buildings (UD) 18,520 Total surface area (m2) 4,216,478.7
Table 1. Mean roof surface area for high-rise apartment buildings in 2007.
The calculation of the number of buildings and their total roof surface area allowed
us to obtain the mean roof surface area for each building type and each year studied.
This operation was repeated for each year and building type in order to obtain the
surface area for each province in Andalusia. For the rest of the building types and years,
we obtained the mean roof surface areas of each building type for new housing
constructed in 2000–2007. These figures were used to estimate the roof surface area of
the total number of buildings (Table 2).
Year Nº. Buildings (UD) Mean Roof Surface Area (m2/building)
Detached Houses
Townhouses High-rise Buildings
TotalDetached Houses
Townhouses High-rise Buildings
2000 105 423 686 1,214 235.42 188.61 186.61 2001 140 559 738 1,437 210.74 173.48 181.56 2002 260 1,152 951 2,363 182.66 154.36 188.22 2003 265 755 1,206 2,226 209.99 198.87 197.51 2004 408 1,151 1,505 3,064 201.37 182.49 183.94 2005 499 993 1,725 3,217 221.62 204.89 175.40 2006 355 877 2,053 3,285 233.83 272.60 227.33 2007 195 581 1,716 2,492 370.22 257.67 226.84
Weighted Mean 226.87 201.36 199.86
Table 2. Mean roof surface area, according to building type (Province of Córdoba) in 2007.
Table 3 shows the data obtained for all of the provinces in Andalusia. It includes the
mean roof surface area for each building type, which was used to obtain rooftop energy
capacity. The total number of residential buildings in Andalusia is approximately
1,400,000. To obtain this information, w updated the housing census of 2001 by
including information from the final building completion certificates, annually
published by the Ministry of Development.
J. Ordóñez et al., 2010
The use of photovoltaic solar energy as an energy source in the residential housing sector 119
Province Total Nº of
Buildings(UD)
Building Types (UD) Flat-Roof Buildings (UD) Pitched Roof Buildings (UD)
Detached House
Town-house
High-rise Building
Detached House
Town-house
High-rise Building
Detached House
Town-house
High-rise Building
Almería 90,134 12,180 26,997 50,957 7,554 16,744 31,605 4,626 10,253 19,352
Cádiz 155,625 17,962 52,349 85,314 8,322 24,254 39,526 9,640 28,096 45,788
Córdoba 132,643 29,941 54,933 47,769 12,481 22,899 19,912 17,460 32,035 27,857
Granada 147,522 33,299 61,095 53,127 7,698 14,124 12,282 25,601 46,971 40,845
Huelva 100,765 8,982 44,525 47,258 3,240 16,061 17,047 5,742 28,464 30,211
Jaén 127,655 15,852 68,639 43,164 2,526 10,939 6,879 13,326 57,701 36,285
Málaga 286,532 64,329 89,363 132,841 18,794 26,108 38,810 45,535 63,255 94,030
Seville 357,996 55,271 159,095 143,631 30,284 87,172 78,699 24,986 71,923 64,932
Total 1,398,871 237,814 556,996 604,061 90,899 218,300 244,760 146,915 338,697 359,301
Table 3. Characterization of the total number of residential buildings in Andalusia according to roof
type.
We extrapolated the characterization of the sample for 2000– 2007 to the total
population. This allowed us to obtain the number of buildings, according to building
type (detached house, town house, or high-rise building) and roof type (flat or pitched).
Table 4 shows the roof surface area of the total number of residential buildings in
Andalusia.
Province Total Flat Roof Surface Area (m2) Total Pitched Roof Surface Area (m2) Total
(thousands of m2)
Detached House
Town- house
High-rise Building
Detached House
Town- house
High-rise Building
Almería 1,563,352.41 3,095,629.80 7,542,885.95 957,257.63 1,895,487.68 4,618,590.84 19,673.20
Cádiz 2,100,249.63 4,178,612.16 8,963,327.45 2,432,965.67 4,840,576.94 10,383,274.28 32,899.01
Córdoba 2,831,505.55 4,610,890.91 3,979,771.24 3,961,158.62 6,450,444.81 5,567,534.61 27,401.31
Granada 1,481,976.63 2,209,545.57 2,357,910.11 4,928,473.86 7,348,083.18 7,841,485.53 26,167.47
Huelva 631,367.86 2,258,196.75 3,458,535.72 1,118,951.74 4,002,125.11 6,129,444.94 17,598.62
Jaén 443,449.89 1,683,831.08 1,131,443.70 2,339,157.46 8,882,054.35 5,968,261.68 20,448.20
Málaga 4,834,293.29 4,311,052.34 9,745,234.92 11,712,635.70 10,444,915.62 23,610,976.71 64,659.11
Seville 5,211,443.61 12,795,433.17 13,050,049.46 4,299,815.55 10,557,152.01 10,767,228.75 56,681.12
Total 19,097,638.89 35,143,191.77 50,229,158.54 31,750,416.22 54,420,839.70 74,886,797.32 265,528.04
Table 4. Roof surface area of the total number of buildings in Andalucía.
3.2 Useful roof surface area
The available roof surface area was obtained by selecting a representative sample of
the population under study, namely the residential buildings in Andalusia. This was
calculated from urban maps obtained from Google EarthTM. These maps were exported
and scaled with the AutoCAD® software application.
Capitulo 4: Capacidad energética de las cubiertas
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 120
This allowed us to obtain data, such as the roof surface area, the surface area of
elements that could interfere with the photovoltaic system, the shaded area, and the
surface occupied by other installations, such as HVAC, elevator shafts, antennas, etc.
(Figs. 2 and 3).
Figures 2 and 3. Calculation of the useful roof surface area, free of obstacles and shading.
Source: Google EarthTM.
The size of the sample was determined by random stratified sampling since the
population under study had been previously divided into subpopulations (homogeneous
strata for the characteristic being studied). An unrestricted random sample was
independently selected for each stratum. An estimator was obtained for each stratum,
which was calculated as an adequate weighting of the estimates. The stratified sampling
technique used was proportionate allocation based on the fact that the size of each
stratum of the sample was proportional to its size within the population [12].
∑
∑
∗∗+
∗
=2
22
1hh
h
hh
sWN
V
wsW
n
where n is the size of the sample; N is the total number of units; hW is the
weighting of the stratum ( NNh ); hw is the weight that stratum h has in the sample
( nnh ); hn is the number of sample units for each stratum; V is the anticipated variance,
based on the margin of error ( 22 td ); d is the chosen margin of error ( )Yy − ; t is the
J. Ordóñez et al., 2010
The use of photovoltaic solar energy as an energy source in the residential housing sector 121
confidence coefficient (1.96 to the 95 % confidence level for a normal distribution
(0,1)); 2hs is the estimated variance of each stratum h ( 2
1)(
11
hhi
n
ih
yyn
h
−∗− ∑
=
).
The margin of error in the sample was 10%. Since the true variance of the
population of each stratum h was unknown, we selected a small sample from the
population of each stratum, and called it the pilot sample. Subsequently, we estimated
the population variance in each of these samples for each building type. Finally, we
applied the formula to estimate the size of the sample, and multiplied the sample size by
each Wh, thus obtaining the population size of each stratum (Table 5).
Typology hh nN = hh wW = 2hs n
Detached and semi-detached
houses 196,691 0.14 2,065.62 111
Townhouses and row houses
476,889 0.34 561.32 269
High-rise buildings
725,291 0.52 38,692.27 409
N 1,398,871 1 789
Table 5. Sample size, according to stratum.
This analysis allowed us to verify the previous data. For example, in the case of
detached and semi-detached houses in Andalusia, the mean roof surface at a confidence
level of 95% occurred within interval (η± 1.96·σ/√(p-n)/(p-1)) and was 215.79 m2. The
mean value, calculated by the previously described statistical analysis, was found to be
210.33 m2, which was also within this interval. The comparison of data obtained with
these two methods confirmed their goodness of fit.
Once the reliability of the data was confirmed by the previously described graphs,
we determined the mean percentage of the useful surface area after eliminating the area
occupied by elements interfering with the photovoltaic array. Table 6 shows the
coefficient values that represent the gross surface area necessary to install the
photovoltaic solar system.
Detached and semi-detached houses Townhouses or row houses High-rise buildings Flat roof Pitched roof Flat roof Pitched roof Flat roof Pitched roof Coeff. Su/ST 0.740 0.974 0.796 0.983 0.654 0.789
Table 6. Relation coefficient to obtain the useful roof surface area, free of obstacles.
Capitulo 4: Capacidad energética de las cubiertas
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 122
3.3 Installation design
Figure 8 shows the diagram of a roof-mounted photovoltaic system connected to the
grid. It is composed of the following elements: (i) photovoltaic module; (ii)
inverter/power conditioner; (iii) meters; (iv) connection to a conventional electrical grid
(Fig.4).
Figure 4. Diagram of a grid-connected photovoltaic solar system.
The expression used to estimate the energy (kWh/day) generated by the system is
the following [13]:
Ep = Gdm(α,β)*Pmp*·PR/GCEM
where Gdm(α,β) is the annual and monthly mean value of the daily irradiation on the
solar generator in kWh./m2día; Pmp is the peak generator power; GCEM is 1 kWh/m2; PR
is the performance ratio.
To estimate the influence that the choice of photovoltaic panel can have on the final
result, we calculated the energy for two installations with different types of panel. The
photovoltaic panel chosen for the installation design was manufactured by ISOFOTON.
This company has its factory in Andalusia and its production in MW was 4.5% of the
total world market for photovoltaic cells in 2004.
PV Generator
Inverter
kWh
Power
consuption
kWh
Meters
Electrical grid
J. Ordóñez et al., 2010
The use of photovoltaic solar energy as an energy source in the residential housing sector 123
3.3.1 Installation type 1
The first installation type was composed of IS-170 photovoltaic modules
manufactured by ISOFOTON, which had the following characteristics at standard test
conditions:
• Dimensions: 790 ± 5 mm x 1600 ± 5 mm x 40 ± 2 mm.
• Maximum power rating: 170 W ± 3% W.
• Open circuit voltage: 44.4 V.
• TONC (800 W/m2, 20 ºC, AM 1.5, 1 m/s) 47 ºC.
3.3.2 Installation type 2
The second installation type was composed of IS-220 photovoltaic modules also
manufactured by ISOFOTON, which had the following characteristics at standard test
conditions:
• Dimensions: 1047 ± 5 mm x 1600 ± 5 mm x 40 ± 2 mm.
• Maximum power rating: 220 W ± 3% W.
• Open circuit voltage: 47.9 V.
• TONC (800 W/m2 , 20 ºC, AM 1.5, 1 m/s) 47 ºC.
Once the modules were defined, we obtained the elevations and layout of the
photovoltaic array for the previously defined mean roof area surfaces. Our purpose was
to determine the energy produced by the solar energy installation per unit of useful roof
surface area (see Figures 5, 6-7).
d
h
Beta
Figure 5. - Distance between solar panels
Capitulo 4: Capacidad energética de las cubiertas
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 124
The distance between photovoltaic modules were calculated by means of the
following expression:
d = h/tan (61o-λ)
In the case of a flat roof, a perimeter space with a width of 1 m was considered
necessary for maintenance work. We then calculated the number of solar panels that
could be installed for the orientations shown in Figure 6 (flat roofs) and Figure 7
(pitched roofs).
b = 20
a = 20
b = 20 Figure 6. Theoretical siting of the photovoltaic modules for two orientations.
Flat roofs. IS-170 Modules.
a = 20
b = 20
a = 20
b = 20
Figure 7. Theoretical siting of photovoltaic modules for two orientations.
Flat roofs. IS-220 Modules.
For pitched roofs, our initial hypothesis was that the photovoltaic system would be
installed on the roof façade receiving the largest amount of solar irradiation, and thus,
the most energy. The array of solar panels would be attached to one of the roof sides.
The mean roof tilt angle obtained from the analysis of a set of projects was found to be
16.708º. For the purpose of calculating the mean radiation, the S-E orientation was
J. Ordóñez et al., 2010
The use of photovoltaic solar energy as an energy source in the residential housing sector 125
considered to be the most representative, and the solar panels would be mounted on the
side of the roof that was most favorable to this orientation (see Figure 8).
b = 20
a = 10
b = 20
Figure 8.- Theoretical siting of IS-170 photovoltaic modules for two types of pitched roof
After obtaining the useful surface area for the location of photovoltaic arrays and
defining the roof layout, we calculated the photovoltaic solar energy potentially
generated. To calculate losses from shading, the shadows produced by various
construction elements (e.g. chimneys, elevator shafts, etc.) were studied by using the
AutoCAD® software program (see figure 9).
Figure 9.- Shadow projection for different days and times. Pitched roof and chimney.
The percentage of solar irradiation loss from shading was obtained by the
representing the profile of the obstacle on the roof in the context of a band of the sun’s
trajectories during the year. As an example, figure 10 shows an elevator shaft located
on the roof of a building.
Figure 10.- Percentage of solar irradiation loss from shading for an elevator shaft located on a building
roof: 17.47%.
Capitulo 4: Capacidad energética de las cubiertas
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 126
The criterion followed in this study, which is based on the Pliego de Condiciones
Técnicas de Instalaciones Conectadas a Red [14] [Technical Specifications for Grid-
Connected Installations] was to eliminate roof surfaces with a solar irradiation loss from
shading greater than 10%.
4 RESULTS
The roof surface area for all residential buildings in Andalusia was found to be
265.52 Km2: 104.47 for buildings with flat roofs and 161.05 Km2 for buildings with
pitched roofs. The useful rooftop surface area, where a photovoltaic array could be
mounted was 218.52 Km2, which comes to 82.29% of the total. The surface occupied by
a photovoltaic array of IS-170 solar panels for each roof type is shown in Table 7.
FLAT ROOF PITCHED ROOF
Detached Houses
Town-houses
High-rise Buildings
Detached Houses
Town-houses
High-rise Buildings
54.97% 53.72% 51.83% 21.12% 20.19% 16.83%
Table 7. Percentage of roof surface area occupied by Installation type 2
For a photovoltaic array of IS-220 solar panels, the occupation coefficient for flat
roofs has the same value. For pitched roofs, the value is also very similar. For example,
in the case of high-rise buildings, this value is 16.44 % for flat roofs as compared to
16.83 % for pitched roofs. The energy generation potential was estimated to be a total of
9,73 GWh for a photovoltaic array of IS-170 solar panels, and 9,38 GWh for an array of
IS-220 solar panels (see Graph 1). The maximum photovoltaic potential for rooftop
surfaces of residential buildings in Andalusia was thus calculated at 10,8 GWh/year.
J. Ordóñez et al., 2010
The use of photovoltaic solar energy as an energy source in the residential housing sector 127
410.92961.05
1,792.85
2,767.09
3,916.70
5,072.79
7,394.30
8,263.858,919.46
9,375.00
396.27926.79
1,728.89
2,668.44
3,777.07
4,891.83
6,074.69
7,130.256,299.61
9,730.23
9,040.179,382.77
8,600.917,968.69
0.00
2,000.00
4,000.00
6,000.00
8,000.00
10,000.00
12,000.00
January
February
March
April
May
June
July
August
Septem
ber
October
Novem
ber
Decem
ber
Total roof energy potential. IS-170 solar panel Total roof energy potential. IS-220 solar panel
Graph 1. Total energy (GWh) generated by each solar panel type. Monthly accumulation.
The monthly distribution is represented on Graph 2.
410.92
550.13
831.80
974.24
1,149.61 1,156.081,094.69
869.55
655.62
396.27
530.53
802.09
939.55
1,108.64 1,114.761,182.86
1,055.56
455.53
1,226.82
355.23439.26
342.61
632.22
838.44
0.00
200.00
400.00
600.00
800.00
1,000.00
1,200.00
1,400.00
January
February
March
April
May
June
July
August
September
October
Novem
ber
Decem
ber
Total roof energy potential. IS-170 solar panel Total roof energy potential. IS-220 Solar panel
Graph 2. Total energy (GWh/month) generated monthly by each solar panel type
The energy capacity for each roof type and m2 of roof surface area for each province
as well as the hypotheses of this research study are defined by the following ratios in
Table 8:
Capitulo 4: Capacidad energética de las cubiertas
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 128
NET COEFFICIENTS GROSS COEFFICIENTS
FLAT ROOF
PITCHED ROOF FLAT ROOF PITCHED
ROOF PROVINCE kWh/m2·year kWh/m2 year kW/m2·year kWh/m2·year Almería 69.51 40.13 46.26 31.54 Cádiz 75.34 43.50 50.20 34.40 Córdoba 63.89 36.39 43.05 30.20 Granada 57.66 33.28 38.79 27.42 Huelva 70.53 40.71 47.02 32.39 Jaén 65.23 37.65 43.83 31.08 Málaga 68.78 39.71 46.08 32.01 Sevilla 64.48 37.22 43.26 30.38
Table 8. Ratios referring to the energy generation capacity per m2 of roof-top surface area
The energy distribution for each Andalusian province is represented in Graph 3.
0.00
50.00
100.00
150.00
200.00
250.00
300.00
350.00
January
February
March
April
May
June
July
August
September
October
Novem
ber
Decem
ber
GRANADA ALMERÍA CÁDIZ CÓRDOBA MÁLAGA
HUELVA SEVILLA JAÉN
Graph 3. Photovoltaic solar energy. Monthly production (GWh/month)
As previously mentioned, the total energy accumulated month by month during the
year for the total number of buildings was approximately 9.5 GWh/year. Of this
amount, 5.0 GWh (51.5% of the total) could be generated by buildings with pitched
roofs, and 4.5 GWh (48.5 % of the total) could be generated by buildings with flat roofs.
J. Ordóñez et al., 2010
The use of photovoltaic solar energy as an energy source in the residential housing sector 129
5 CONCLUSIONS
In 2006, the energy consumption for uses related to the residential housing sector in
Andalusia was 12,320 GW/year. The photovoltaic solar energy capacity for residential
building rooftops in Andalusia if photovoltaic arrays were installed on all of them was
calculated at 9.73 GW/year for a total roof surface of 265.52 Km2.
This would satisfy 78.89% of all energy needs, and would signify an external energy
dependence of only 21.02%. Even this figure could be vastly improved if energy
efficiency was increased and energy consumption was reduced. This seems to indicate
that energy sustainability of residential dwellings in Andalusia is totally viable if the
measures proposed in this study are taken.
This research clearly shows the importance of the design of roof-mounted elements
when it comes to optimizing energy production.
REFERENCES
[1] Xiaowu W, Ben H. Energy analysis of domestic-scale solar water heaters.
Renewable and Sustainable Energy Reviews 2005;639–45.
[2] Jefferson Michael. Sustainable energy development: performance and prospects.
Renewable Energy 2006;31:571–82.
[3] Jäger-Waldau Arnulf. Photovoltaics and renewable energies in Europe.
Renewable and Sustainable Energy Reviews 2007;11:1414–37.
[4] Celik A. Present status of photovoltaic energy in Turkey and life cycle techno-
economic analysis of a grid connected photovoltaic-house. Renewable and Sustainable
Energy Reviews 2006;10:370–87.
[5] Bojic M, Blagojevic M. Photovoltaic electricity production of a grid-connected
urban house in Serbia. Energy Policy 2006;34:941–2948.
[6] Arán Carrión J, Espín Estrella A, Aznar Dols F, Ramos Ridao A. The electricity
production capacity of photovoltaic power plants and the selection of solar energy sites
in Andalusia (Spain). Renewable Energy 2008;33:545–52.
[7] Ordóñez García Javier, Gago Eulalia Jadraque, Bayo Javier Alegre, Montes
Germán Martínez. The use of solar energy in the building construction sector in Spain.
Renewable and Sustainable Energy Reviews 2007;11:2166–78.
Capitulo 4: Capacidad energética de las cubiertas
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 130
[8] Ramos Ridao Ángel, García Ernesto Hontoria, Escobar Begoña Moreno,
Montserrat Zamorano Toro. Solar energy in Andalusia (Spain): present state and
prospects for the future. Renewable and Sustainable Energy Reviews 2007;11:148–61.
[9] Sidrach-de-Cardona M, Mora López Ll. Evaluation of a grid-connected
photovoltaic system in southern Spain. Renewable Energy 1998;15:527–30.
[10] Izquierdo Salvador, RodriguesMarcos, Fueyo Norberto. Amethod for
estimating the geographical distribution of the available roof surface area for large-scale
photovoltaic energy-potential evaluations. Solar Energy 2008;82:929–39.
[11] Lukas G. Swan, V. Ismet Ugursal. Modelling of end-use energy consumption in
the residential sector. A review of modelling techniques. Renewable and Sustainable
Energy Reviews 2009,13:1819–1835.
[12] William G. Cochran. Professor of Statistics. Harvard University. Sampling
Techniques. C.E.C.S.A. April 1975.
[13] Méndez J, Cuervo R. Energía solar fotovoltaica. Madrid: FC Editorial; 2008,
ISBN-3: 978-84-96743-45-8.
[14] IADE. Instalaciones de Energía Solar Fotovoltaica Pliego de Condiciones
Técnicas de Instalaciones conectadas a Red; 2002.
Capítulo V: Modelo Energético
E. Jadraque et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 131
DEVELOPMENT OF AN ENERGY MODEL FOR THE
RESIDENTIAL SECTOR: ELECTRICITY
CONSUMPTION IN ANDALUSIA (SPAIN) E. Jadraque, A. Espín, J. Ordóñez
Department of Civil Engineering, University of Granada, Spain
Abstract
Electrical energy consumption in the residential sector has soared over the years.
This is largely due to the growing number of residential housing units. The development
of models allows us to estimate and predict the evolution and behavior of electricity
consumption in this sector as well as its end-uses. The data thus obtained are extremely
useful for the elaboration of energy-saving measures that can enhance energy efficiency.
In June 2008 the Spanish government approved a set of guidelines in the document
titled, Estrategia Española de Cambio Climático y Energía Limpia [Spanish Strategy
for Climate Change and Clean Energy]. Its main objective was to replace conventional
incandescent light bulbs with energy-saving light bulbs in the residential sector. This
process would be carried out over a three-year period. This article describes the design,
development, and application of a model capable of calculating electricity consumption
for lighting in the residential housing sector. These results were reinforced by data from
questionnaires administered to a representative sample of households. Finally, this
energy model was applied to Andalusia. This allowed us to obtain the savings in
electricity consumption for lighting when the objectives in the Spanish strategy for
energy conservation had been achieved. © 2011 Elsevier B.V. All rights reserved.
Keywords: Lighting, Edification, Energy consumption, Energy model.
0378-7788/$ – see front matter © 2011 Elsevier B.V. All rights reserved.
doi:10.1016/j.enbuild.2011.01.016
Capitulo 5: Modelo energético
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 132
1 INTRODUCTION
In Spain the residential sector is responsible for 10% (10,793 ktep) of the total
energy consumption [1] in the country. A residential building can be defined as any
structure, in which at least 50% of its useful surface is continuously inhabited by people,
regardless of whether the building fulfills a secondary function, and whether the
inhabitants of the building live there either temporarily or permanently [2].
From 2000 to 2006, the number of housing units increased by 90.35%, reaching a
total of 23,859,014 in 2006 [3]. Not surprisingly, this growth was accompanied by a
corresponding increase in electricity consumption in the residential housing sector. For
example, in Andalusia, the distribution of electricity consumption in 2006 (35,342
GWh) was the following: residential sector, 34.9% (12,320 GWh); service sector,
33.4% (11,807 GWh); industrial sector, 26.5% (9,367 GWh); primary sector, 4.1%
(1,455 GWh); and transportation sector, 1% (393 GWh) [4]. The importance of
electricity consumption in the residential sector justifies the development of models
capable of calculating different end-uses (HVAC, appliances, lighting, water heating,
plumbing, etc.), which depend on electricity. In fact, several such models have been
developed and proposed [5-9].
Energy efficiency in residential housing units is currently a priority in national and
international energy policies [10,11]. The document titled La Estrategia de Ahorro y
Eficiencia Energética en España [Strategy for Energy Conservation and Efficiency in
Spain] [1], proposed a series of guidelines until 2010 for the reduction of energy
consumption for lighting in buildings. For example, one of these guidelines was the
replacement of conventional incandescent light bulbs with energy-saving light bulbs. In
June 2008, the Spanish government enacted the strategic measures proposed in
Estrategia Española de Cambio Climático y Energía Limpia [Spanish Strategy for
Climate Change and Clean Energy]. Its main objective is the progressive replacement in
a three-year period of conventional incandescent light bulbs with energy-saving light
bulbs in the residential sector [12]. The following sections describe a model which was
used to obtain the electric energy consumption for lighting in the residential sector in
Andalusia with a view to evaluating the energy-saving measures implemented by the
Spanish government.
E. Jadraque et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 133
2 OUTLINE THE MODEL
The model developed in this research study (see Figure 1) was used to calculate the
electricity consumption for lighting as the product of the total nominal power used in
households in accordance with the hours of energy consumption. The total nominal
power was calculated by determination of the local median illumination, which allowed
us to obtain the number and type of luminaires or lamps needed to provide the desired
average level of illuminance. This calculation took into account both the direct as well
as the reflected luminous flux, taking into account a series of factors like the type of
housing unit, illumination units, and light source characteristics. The data regarding the
types of light source (incandescent, fluorescent, halogen, low energy consumption) were
obtained by questionnaires administered to a representative sample of the population.
The hours of electricity consumption were estimated by taking into account the
hours of daylight, activity of the household occupants, results of the questionnaire, and
the consumption models of other authors. We then contrasted the results of our model
with the consumption obtained from the statistical analysis of the questionnaire data and
with the consumption values obtained by other authors.
Determinationof the local
median illumination
Power
Ilumination units
Questionnaires Consumption
of electrical energy for
lighting
Type of housing unit: Apartment blockDetached/semi-detachedTownhouse/rowhouse
Light sources: IncandescentFluorescentHalogenLow-consumption
Hours of electricityconsuption
Natural light
Occupant activity
Other models
Calibration of the model
Figure. 1. Structure of the model.
Capitulo 5: Modelo energético
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 134
3 CALCULATIN ELECTRICAL POWER BY DETERMINATION OF THE
LUMINOUS FLUX
3.1 Units and systems of illumination
An illumination unit is regarded as one or more luminaires connected to a switch.
The number of illumination units installed, specific illumination, technologies used, and
electrical power values vary from one house to another, depending on the choice of the
users. For the calculation of these parameters, the model estimates by determination of
the luminous flux the minimum number of luminaires necessary for each space or room
in the household, which guarantee a mean level of illumination [13] that permits the
optimal performance of activities by household members.
Luminous flux (Φ) can be defined as the quantity of light emitted in all directions by
a source of visible light per time unit [14]. It is the function of the surface area of the
space (S), illuminance level (Em), use coefficients of the space (fu), and the conservation
of the lamps and luminaires (fc). Its unit of measurement is the lumen, which is given by
the following expression [15]:
cu
m
ffSE
∗∗
=Φ
The luminous flux depends on the power (W) and performance of the lamp-
luminaire (η) chosen to light the room, and is represented by the formula below [15]:
WηΦ ∗=
In this way it was possible to obtain the power needed for lighting, which, when
multiplied by the number of hours that these luminaires were switched on, gave the
electricity consumption. In order to know the types of light source used in each
household (e.g. incandescent, halogen, fluorescent, low-energy consumption, etc.), these
data were extracted from questionnaires administered to households in 2009.
Before this data collection process, the questionnaire was first piloted to a
representative sample of randomly selected households with a view to detecting errors
E. Jadraque et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 135
or inconsistencies. These pilot results were not included in the data set presented in this
study. The questionnaire included information pertaining to the light sources, such as
the number and type of light bulbs used in the house as well as the number of hours that
they were turned on.
For each type of housing unit (apartment block, detached/semi-detached houses, and
row houses/townhouses), a percentage was obtained that indicated the use of light bulb
types (incandescent, halogen, fluorescent, low energy consumption, and others) in each
housing category (see Table 1).
Apartment
block Detached/
Semi-detached housing units
Row houses/Townhouses
Incandescent 38 29 31 Halogen 28 6 49 Fluorescent 7 3 2 Low energy consumption 27 61 18 Others 0 1 0
Table 1. Percentages of types of light bulbs for different housing profiles.
4 CHARACTERIZATION OF RESIDENTIAL HOUSING UNITS
In 2006 Andalusia had a total of 4,163,281 housing units [3], which amounted to
17.5% of all housing in Spain [16]. Andalusia is also the leading region in Spain in the
construction of new homes. In fact, 20.7% of all new housing units in 2006 were built in
this region [17]. Statistical data were collected for 2004-2006 to characterize the
housing units in Andalusia. This information was obtained from the Dirección General
de Programación Económica [Directorate General of Economic Programming], an
agency of the Secretaría de Estado de Infraestructuras [State Department for
Infrastructure], which is a subsection of the Ministry of Fomento [Ministry of Public
Works] in Spain. In Spain the Ministerio de Fomento collects data on a monthly basis
for the whole country. The treatment of the response, “no answer given”, on certain
questionnaires was handled by stratifying city halls in provinces by calculating
expansion coefficients based on the city population and the number of licenses granted.
The formula used was the following:
Capitulo 5: Modelo energético
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 136
ij
ij
ij
ijij b
BaA
C ×=
where Cij is the elevation coefficient of stratum i in province j, Aij is the population of
towns of stratum i in province j, aij is the population of towns of stratum i in province j,
who answered the questionnaire, Bij is the number of licenses granted in stratum i in
province j, bij is the number of licenses of stratum i in province j with a questionnaire.
This expansion coefficient uses the first factor Aij/aij to correct the refusal to
answer, and Bij/bij to correct the non-completion of questionnaires. In order to obtain
the final results, questionnaires of each stratum-province were added, and the resulting
figure was multiplied by the coefficient. The size of the sample (i.e. the minimum
number of towns that should be received from each stratum (n)), depends on the total
number of towns (N), the desired confidence level (K), the variability of the licenses
granted (s), and the absolute error assumed for these licenses (e) [18]. The formula used
was the following:
( )222
222
+ SKNeSKNn∗∗
∗∗=
The study focused on buildings with a mainly residential use. After the statistical
treatment of data from 2004, 2005, and 2006, we then analyzed a series of building-
design parameters, such as building type, surface, number of rooms, etc. Three
categories were defined, which were representative of different residential building
types (i.e. detached/semi-detached, row house/townhouse, and apartment block), and
which define the sample (see Table 2).
Housing unit types Nº of housing units
Detached/Semi detached houses 333,516
Row houses/ Townhouses 788,768Apartment blocks 3,040,997
TOTAL 4,163,281
Table 2. Type and number of residential housing units in Andalusia (based on data from the Ministerio de
Vivienda and the Ministerio de Fomento).
E. Jadraque et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 137
This allowed us to obtain the mean design parameters to define three basic
residential housing types.
(a) Apartment block: The typical apartment building has a ground floor as well as
two upper floors. The mean number of rooms per dwelling in the sample is two
bedrooms, living-dining room, half bath, full bathroom, and kitchen.
(b) Detached/semi-detached housing unit profile: This building has a ground floor
as well an upper floor. The mean number of rooms for the sample was the following:
three bedrooms, living-dining room, half-bath, full bathroom, and kitchen [17].
(c) Row houses/Townhouses: This housing unit profile has a ground floor and upper
floor. The average number of rooms per dwelling is three bedrooms, living-dining
room, half bath, full bathroom, and kitchen [17].
We then obtained the number of occupied housing units of the total number of
houses, which are potential sources of electricity consumption. The statistical data was
obtained from the Spanish Ministry of Housing (see Table 3) [19].
Housing unit types Nº of occupied housing units
Detached/Semi detached houses 281,488Row houses/ Townhouses 665,720Apartments 2,566,601
TOTAL 3,513,809
Table 3. Final distribution of housing unit types based on data from the Spanish Ministry of Housing and the Spanish Ministry of Public Works.
5 NUMBER OF LUMINAIRES AND NOMINAL POWER
The number of luminaires and the nominal power of the installation (Table 4) were
obtained on the basis of the following: (i) the different types of light source (Table 1);
(ii) the building characterization that defines the ground plan of each housing unit
profile; (iii) the luminous flux necessary in each room or living space of the dwelling,
obtained with the previously mentioned formulas.
Capitulo 5: Modelo energético
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 138
Housing unit types Total number of luminaires
Total nominal power
Detached/Semi detached houses 47 1,896.00
Row houses/ Townhouses 40 2,400.00 Apartments 122 6,470.00
Table 4. Total number of luminaires, and total nominal power.
6 NATURAL LIGHT
Human perception of the level of natural light within a building is a key factor in
determining the use of electrical light [20-22]. Our model is based on a series of
hypotheses pertaining to the hourly consumption of electricity in each housing unit,
depending on the season of the year. For this purpose, January, February, March,
November, and December were considered to be winter months, whereas April, May,
June, July, August, September, and October were regarded as summer months. For this
classification, we took into account the time changes at the beginning of the spring and
fall since this modifies the electrical light necessary to carry out daily activities in the
buildings, and thus, their electrical consumption [23].
7 HOUSEHOLD PROFILES
The number and activity of the people living in the house is another key factor in
determining the electricity consumption in lighting [21,24-26]. Current social
tendencies such as retirement age, age structure, welfare system, vacation periods and
social life are fundamental when analyzing energy consumption in family households
[27,28]. The presence in the home of family members affects energy consumption.
Retirees are not the only ones who spend a lot of time at home. Others who remain at
home for long periods of time are couples who obtain maternity/paternity leave, not to
mention those family members that work from home. Furthermore, it is also necessary
to know when the residence is generally empty, and as a result, one must also take into
account working days and holidays.
The population demographics in Andalusia are similar to that in Spain and other
European countries, though with certain distinctive characteristics. Generally speaking,
population aging is progressing rapidly in Andalusia, and there is a loss of demographic
E. Jadraque et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 139
power, stemming from declining fertility and the low birth rate [29]. This can influence
electricity consumption for lighting since there are hypotheses that show that older
people (age 65 or more) consume less electricity for lighting than younger age groups
[25].
This research is based on a study carried out in 2006 by the Instituto de Estadística
de Andalucía [30] [Andalusian Institute of Statistics]. Table 5 shows the values obtained
for household type, average household size, and the number of households.
Profile no. Household profile Average household size
Number of households (per thousand)
Profile 1 Couple with children 3.95 1,391.90 Profile 2 Couple without children 2.10 438.00 Profile 3 Parent with children 2.85 250.10 Profile 4 Single-member family 1.00 448.20 Profile 5 Multi-member family 2.40 44.80
TOTAL 2,572.90
Table 5. Family structure of Andalusian households based on data from the Instituto de Estadística de
Andalucía [Andalusian Institute of Statistics].
Based on the residential building type obtained from the questionnaires and on the
characteristics of Andalusian families, we obtained the distribution of households per
building type (see Table 6).
Detached/Semi-detached house
Row house/Townhouse
Apartment block
Profile 1 111,503.64 263,707.08 1,016,689.28 Profile 2 35,087.72 82,982.76 319,929.53 Profile 3 20,035.25 47,383.53 182,681.22 Profile 4 35,904.83 84,915.23 327,379.94 Profile 5 3,588.88 8,487.73 32,723.39 TOTAL 206,120.31 487,476.34 1,874,403.35
Table 6. Number of households per residential building type based on data from the Instituto de
Estadística de Andalucía and our questionnaire
8 CALCULATION OF THE ELECTRICITY CONSUMPTION FOR
LIGHTING
The electrical energy consumed for lighting was obtained as a product of the hours
of consumption of the various household profiles in each of the residential building
Capitulo 5: Modelo energético
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 140
types. This was measured according to the power of the lamps used in different
household activities. The number of hours during which the light sources in each room
consumed energy was obtained from the questionnaire data. These data were contrasted
with the data obtained with the hourly distribution of electricity consumption published
by other authors [24,25,31]. By way of example, the following graphs show the hourly
electrical energy consumption for lighting (Graphs 1-4).
0
100
200
300
400
500
600
700
800
900
1.000
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7
Winter working day Summer working day Winter holiday Summer hol iday Graph 1. Electrical energy consumption for lighting for household profile 1 in a townhouse/row
house (Wh).
0
200
400
600
800
1.000
1.200
1.400
1.600
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7
Winter working day Summer w orking day Winter holiday Summer hol iday
Graph 2. Hourly electrical energy consumption for lighting for household profile 2 in an apartment block (Wh).
E. Jadraque et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 141
0
100
200
300
400
500
600
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7
Winter working day Summer working day Winter holiday Summer hol iday Graph 3. Hourly electrical energy consumption for lighting for household profile 3 in a
detached/semi-detached residential unit.
0
100
200
300
400
500
600
700
800
900
1.000
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7
Winter working day Summer working day Winter holiday Summer hol iday
Graph 4. Electrical energy consumption for lighting for household profile 4 in an apartment block
(Wh).
Electrical energy consumption for lighting can be divided into two time zones:
• Low consumption zone: In this time period, lighting consumption is
at a minimum though there is a slight increase in the early morning of
working days when activity is just beginning.
• High consumption zone: Lighting consumption in this zone is
conditioned by the time change. There is a variation of approximately 2 h
between the beginning of electricity consumption in winter and in summer.
Consumption peaks appear at the times of the day when household activity is
most intense. Energy consumption tends to be greater on holidays.
Capitulo 5: Modelo energético
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 142
Graph 5 shows the annual consumption un kWh for each household profile an
building type.
0,00
100,00
200,00
300,00
400,00
500,00
600,00
700,00
800,00
900,00
Household profile 1 Household profile 2 Household profile 3 Household profile 4 Household profile 5
Row house/Townhouse Detached/semi‐detached Apartment block
Graph 5. Monthly energy consumption for lighting for building profiles (kWh).
For a given year the total electrical energy (GWh) for lighting in the residential
housing sector can be obtained with the following expression:
ijijFFijLL
jiT NCnCn
∗⎟⎟⎠
⎞⎜⎜⎝
⎛ ∗+∗= ∑
910)(
C
where nL is the number of working days per month, CLij is the electricity
consumption for lighting per working day (Wh) for each building type (i) of each
household profile (j), nF is the number of holidays per month, CFij is the electricity
consumption for lighting per holiday (Wh) for each building type (i) of each household
profile (j), Nij is the number of households in each profile that occupy each building
type (see Table 3).
The following data were thus obtained (Table 7):
E. Jadraque et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 143
Profile Detached/Semi-detached
Row house/Townhouse
Apartment block
Household profile 1 58.30 223.15 498.00
Household profile 2 14.12 44.72 99.33
Household profile 3 9.25 30.58 84.81
Household profile 4 11.52 32.02 72.58
Household profile 5 1.55 5.03 12.68
Total 94.75 335.49 767.40
Table 7. Annual electricity consumption for lighting per household profile and building type (GW/h).
The final total electrical energy demand in Andalusia for the year was 35,342 GWh.
Of this demand, 12,320 GWh corresponded to electricity consumption in the residential
sector [4]. Based on the distribution of percentages according to the light source used in
each building type, our energy model indicates that electrical energy consumption for
lighting (1,197.64 GWh) makes up 3.39 % of the total electrical energy demand in
Andalusia and 9.72 % of the electricity demand in the residential sector in Andalusia.
When this model is applied and conventional light bulbs are replaced with low energy-
consumption bulbs, the model shows that electrical energy consumption for lighting
will be 2.78% of the total electrical energy demand in Andalusia and 7.96% of the
electricity demand in the residential sector.
9 COMPARISON OF THE MODEL WITH QUESTIONNAIRE DATA
9.1 Questionnaire
The selection of the size of the sample was performed by random stratified sampling
since the population studied was previously divided into subpopulations or strata that
were assumed to be homogeneous in respect to the characteristic analyzed. Within each
stratum, we independently selected a random sample. We then calculated estimators for
each stratum, and the population estimator was calculated as an adequate weighting of
the estimates per stratum. We used the stratified proportional sampling in which the size
of each stratum in the sampling is proportional to its size in the population [32].
Capitulo 5: Modelo energético
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 144
∑
∑
∗∗+
∗
=2
22
1hh
h
hh
sWN
V
wsW
n
where n is the size of the sample, N is the total number of units, hW is the weighting
of the stratum ( NNh ), hw is the weight of stratum h in the sample ( nnh ), hn is the
number of units in the sample for each stratum, V is the variance anticipated,
depending on the margin of error ( 22 td ), d is the margin of error chosen ( )Yy − , t
is the reliability coefficient (1.96-95% confidence for a normal distribution (0,1)), 2hs is
the estimated variance for each stratum h ( 2
1
)(1
1hhi
n
ih
yyn
h
−∗− ∑
=
).
The admissible error in the sample population was set at 10%. Since the true
variance of the population of each stratum h was unknown, a small population sample
was selected from each stratum as a pilot sample. Subsequently, with each sample, the
population variance( 2hs ) was estimated for each of the three building types. Finally, the
formula was used to estimate the size of the population. Once the size of the population
was estimated, it was multiplied by each hW in order to obtain the population size of
each stratum. The statistical treatment of the data collected by the questionnaire
revealed that the percentage of households with some low-consumption lighting was
80% for a confidence level of 95%. In contrast, the Encuesta Social de Hogares y
Medio Ambiente en Andalucía [Survey of Households and the Environment in
Andalusia], administered in 2008, estimated that the percentage of Andalusian
households with at least one low-energy lamp as a lighting source was 85.1% [33].
The calculation of the electricity consumption per household according to building
type was obtained by multiplying the number of hours when the light bulb types were
functioning by their power. We thus obtained the following consumption for each
building type: (i) 2,032.32 kWh for apartment blocks; (ii) 297.11 kWh for row
houses/town houses; (iii) 811.21 kWh for detached/semi-detached houses. Based on all
of the residential housing units in Table 3, this gave a total of 1,469.37 GWh.
E. Jadraque et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 145
This consumption represents a mean consumption of 4.16 % of the total electrical
energy demand in Andalusia, and 11.93 % of the electrical energy demand in the
residential sector.
10 CONCLUSIONS
In conclusion, when the results obtained with our model were contrasted with the
results obtained from questionnaires as well as the models of other researchers [34], this
showed that energy consumption for lighting amounted to approximately 3.8% of the
total electrical energy demand in Andalusia.
The model proposed in this article allowed us to estimate the electrical energy
consumption for lighting in all of the residential housing units in Andalusia. Our results
showed that the most energy-efficient building type, which had the lowest electricity
consumption for lighting, was the apartment block, depending on the household profile
(see Table 8).
Profile Apartment blockHousehold profile 1 489.83
Household profile2 310.47
Household profile 3 464.28
Household profile 4 221.69
Household profile 5 387.38
Total 1,873.65 Table 8. Annual electrical energy consumption for lighting according to household and residential
building type (kWh/year house)
The replacement of incandescent light bulbs with low-consumption bulbs signifies
an opportunity to improve energy efficiency in the residential sector. Current
government policies that encourage the progressive use of more energy-efficient
lighting in rooms (living room and bedrooms) would mean, only in Andalusia, a
reduction of 3.39–2.78=0.61% in the total electrical energy consumption. This would
signify a reduction of 18% in the electricity bill for lighting. The results of our study
show the effectiveness of national policies in Spain to improve lighting efficiency in the
residential building sector.
Capitulo 5: Modelo energético
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 146
11 ACKNOWLEDGEMENTS
The authors wish to thank Añil Construcciones y Servicios, S.A, who provided the
funding for this research.
REFERENCES
[1] IDAE, Estrategia de ahorro y eficiencia energética en España 2004–2012. Plan
de acción 2008–2012. Ministerio de Industria, Turismo y Comercio, Instituto para la
Diversificación y Ahorro de la Energía, 2007.
[2] Ministerio de Vivienda, Estadística de la Vivienda. www.mviv.es, 2006.
[3] Ministerio de Vivienda, Estimación del Parque de Viviendas. Secretaría General
Técnica. Subdirección General de Estudios y Estadísticas. www.mviv.es, 2006.
[4] Agencia Andaluza de la Energía, Datos energéticos de Andalucía 2006.
Consejería de Innovación, Ciencia y Empresa. Junta de Andalucía.
www.agenciaandaluzadelaenergia.es, 2006.
[5] I. Richardson, M. Thomson, D. Infield, A. Delahunty, Domestic lighting: a high-
resolution energy demand model, Energy and Buildings 41 (2009) 781–789.
[6] Y. Yamaguchi, Y. Shimoda, M. Mizuno, Proposal of a modelling approach
considering urban form for evaluation of city level energy management, Energy and
Buildings 39 (2007) 580–592.
[7] J. E. Seem, Pattern recognition algorithm for determining days of the week with
similar energy consumption profiles, Energy and Buildings 37 (2005) 127–139.
[8] A. Al-Mumin, O. Khattab, G. Sridhar, Occupants behaviour and activity patterns
influencing the energy consumption in the Kuwaiti residences, Energy and Buildings 35
(2003) 549–559.
[9] L. Farinaccio, R. Zmeureanu, Using a pattern recognition approach to
disaggregate the total electricity consumption in a house into the major end-uses,
Energy and Buildings 30 (1999) 245–259.
[10] L. Pérez-Lombard, J. Ortiz, C. Pout, A review on buildings energy
consumption information, Energy and Buildings 40 (2008) 394–398.
[11] K. Blok, Enhanced policies for the improvement of electricity efficiencies,
Energy Policy 33 (2005) 1635–1641.
E. Jadraque et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 147
[12] Palacio del Congreso de los Diputados, Proposición de ley de ahorro y uso
eficiente de la energía, Madrid, 9 January, 2008.
[13] Norma UNE 12464-I, y las instalaciones de alumbrado interior, 2003.
[14] A. Espín Estrella, F. Aznar Dols, E.R. Manzano, A. Espín Martín,
Luminotecnia Básica para Ingenieros, 2009, ISBN 978-84-92680-10-8.
[15] F. Martín Sánchez, Manual Práctico de Iluminación, Principios de las Fuentes
de Luz Artificial, 2005, ISBN:84-87440-10-X. [16] Ministerio de Vivienda, Estimación
del Parque de Viviendas. Viviendas principales y no principales por comunidades
autónomas y provincias, Series 2002–2006. www.mviv.es, 2006.
[17] Ministerio de Fomento, Construcción de Edificios 2000–2006. Licencias
Municipales de Obras. Series Estadísticas. www.fomento.es, 2006.
[18] J.O. García, E.J. Gago, J.A. Bayo, G.M.Montes, The use of solar energy in the
buildings construction sector in Spain, Renewable and Sustainable Energy Reviews 11
(2007) 2166–2178.
[19] Ministerio de Vivienda, Encuesta sobre Tenencia y Uso de la Vivienda de los
Hogares para el año 2006. www.mviv.es, 2006d.
[20] C.F. Reinhart, Lightswitch-2002: a model for manual and automated control of
electric lighting and blinds, Solar Energy 77 (2004) 15–28.
[21] R. Yao, K. Steemers, A method of formulating energy load profile for domestic
buildings in the UK, Energy and Buildings 37 (2005) 663–671.
[22] D.R.G. Hunt, The use of artificial lighting in relation to daylight levels and
occupancy, Building and Environment 14 (1979) 21–33.
[23] M.B.C. Aries, G.R. Newsham, Effect of daylight saving time on lighting
energy use: a literature review, Energy Policy 36 (2008) 1858–1866.
[24] A. Capasso, W. Grattieri, R. Lamedica, A. Prudenzi, A bottom-up approach to
residential load modeling, IEEE Transactions on Power Systems 9 (2) (1994).
[25] M. Bladh, H. Krantz, Towards a bright future? Household use of electric light:
a microlevel study, Energy Policy 36 (2008) 3521–3530.
[26] A. Wright, S. Firth, The nature of domestic electricity-loads and effects of time
averaging on statistics and on-site generation calculations, Applied Energy 84 (2007)
389–403.
[27] A. Druckman, T. Jackson, Household energy consumption in the UK: a highly
geographically and socio-economically disaggregated model, Energy Policy 36 (2008)
3177–3192.
Capitulo 5: Modelo energético
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 148
[28] M. Santamouris, K. Kapsis, D. Korres, I. Livada, C. Pavlou, M.N.
Assimakopoulos, On the relation between the energy and social characteristics of the
residential sector, Energy and Buildings 39 (2007) 893–905.
[29] CES, Consejo Europeo y Social de Andalucía. Informe sobre la Situación
Socioeconómica de Andalucía 2006, Junta de Andalucía, 2006, www.ces.es.
[30] IEA, Instituto de Estadística de Andalucía. Consejería de Economía y
Hacienda, Junta de Andalucía, 2006, www.juntadeandalucia.es.
[31] M. Stokes, M. Rylatt, K. Lomas, A simple model of domestic lighting demand,
Energy and Buildings 36 (2004) 103–116.
[32] W.G. Cochran, Professor of Statistics, Harvard University, Sampling
Techniques. C.E.C.S.A. April, 1975.
[33] IEA, Encuesta social 2008. Hogares y medio ambiente en Andalucía.
Consejería de Economía y Hacienda, Junta de Andalucía, 2008,
www.juntadeandalucia.es.
[34] D.L. Loe, Energy efficiency in lighting – considerations and possibilities,
Lighting Research Technology 41 (2009) 209–218.
Capítulo VI: Conclusiones
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 149
CONCLUSIONES
Un aumento en las políticas encaminadas a la construcción de edificios
energéticamente eficientes podría constituir un importante instrumento en los esfuerzos
para aliviar la dependencia de las importaciones de energía de los países que
constituyen la UE (se estima que podría alcanzar el 80% en el año 2020) y cumplir el
Protocolo de Kyoto para reducir las emisiones de dióxido de carbono. Todo ello dentro
de las exigencias marcadas por la Directiva 2010/31/UE relativa a la eficiencia.
Esta investigación pone de manifiesto la importancia que tiene el diseño de los
elementos de la cubierta a la hora de optimizar la energía que podría generarse. En
2006, el consumo de energía destinado a satisfacer los usos relacionados con el sector
de la vivienda residencial en Andalucía fue 12.320 GW/año. La capacidad energética
solar fotovoltaica de las cubiertas de los edificios residenciales de Andalucía, instalando
paneles fotovoltaicos en las cubiertas de todos ellos se calculó en 9,73 GW/año para una
superficie de cubierta total de 265,52 Km2. Esto respondería al 78,89% de todas las
necesidades de energía, que significa una dependencia energética exterior de 21,02%.
El modelo energético desarrollado señala que el consumo de energía eléctrica para
iluminación (1.197,64 GWh.) supone el 3,39% de la demanda total de energía eléctrica
en Andalucía y el 9,72% de la demanda de energía eléctrica del sector residencial en
Andalucía.
El reemplazo de las bombillas incandescentes por otras de bajo consumo representa
una gran oportunidad de mejora para la eficiencia del sector residencial, reduciéndose el
consumo de energía eléctrica para iluminación al 2,78% de la demanda total de energía
eléctrica en Andalucía y al 7,96% de la demanda de energía eléctrica del sector
residencial, lo que supondría una reducción del 0,61% en el consumo total de energía
eléctrica que representaría una disminución del 18% de la factura eléctrica
correspondiente al uso de iluminación.
El consumo de energía eléctrica para iluminación (1.197,64 GWh.) podría ser
cubierto en su totalidad por la energía eléctrica generada utilizando paneles
fotovoltaicos en las cubiertas de los edificios (aproximadamente 9.500 GWh.). El
consumo de energía eléctrica para iluminación representaría un 12,6% de la capacidad
energética solar fotovoltaica de las cubiertas de los edificios residenciales.
Conclusions/Conclusiones
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 150
CONCLUSIONS
The increasing number of policies to foment the energy-efficient construction of
buildings is an important reflection of the efforts of EU member states to reduce their
dependence on imported energy (a figure that is estimated to be as high as 80% in 2020)
and comply with the Kyoto Protocol to reduce carbon dioxide emissions. This is all
occurring within the context of the demands set out in Directive 2010/31/EU of the
European Parliament on energy efficiency.
The research presented in this PhD dissertation reveals the importance of the design
of building roof elements in the optimization of potential energy. In 2006, energy
consumption intended to satisfy uses related to the residential building sector in
Andalusia were 12,320 GW/year. The photovoltaic solar energy capacity of residential
building roofs in Andalusia (if photovoltaic panels were installed on all of them) was
calculated at 9.73 GW/year for a total roof surface of 265.52 Km2. This responds to
78.89% of all energy needs, which signifies an outside energy dependence of 21.02%.
The energy model developed indicates that electrical energy consumption for
lighting (1,197.64 GWh) amounts to 3.39% of the total electrical energy demand in
Andalusia and 9.72% of the electrical energy in the residential sector in Andalusia. The
replacement of incandescent light bulbs with low-energy light bulbs is an important
opportunity to improve energy efficiency in the residential sector by reducing electricity
consumption for lighting uses to 2.78% of the total electrical energy demand in
Andalusia and to 7.96% of the electrical energy demand of the residential sector. This
would mean a reduction of 0.61% in the total consumption of electrical energy, which
in turn would represent a reduction of 18% in the electricity bill for lighting uses.
Electrical energy consumption for lighting (1,197.64 GWh) could be totally covered
by electrical energy generated with photovoltaic panels on building roofs
(approximately 9,500 GWh). Electrical energy consumption for illumination would
come to 12.6% of the photovoltaic solar energy capacity of residential building roofs.
Capítulo VII: Perspectivas de Trabajo Futuras
Tesis doctoral: Eulalia Jadraque Gago, 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 151
PERSPECTIVAS DE TRABAJO FUTURAS
Se proponen como futuras líneas de investigación:
1. Completar el modelo desarrollado que permite obtener el consumo energético
para el resto de los usos originados en la vivienda residencial (ACS, calefacción, aire
acondicionado, electrodomésticos, etc.), que no han sido estudiados en esta tesis.
2. Estudiar el uso de otras fuentes de energía renovables que permitan además de
obtener energía para autoconsumo de la vivienda residencial generar energía eléctrica y
verter a la red la no consumida.
El objetivo de estas futuras líneas de investigación será conseguir la viabilidad
económica de los sistemas energéticos que permitan la sostenibilidad energética de la
vivienda residencial.
Anexo: Otras Publicaciones
Anexo: Evaluation of the accuracy of mathematical models through use of multiple metrics
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 152
EVALUATION OF THE ACCURACY OF
MATHEMATICAL MODELS THROUGH USE OF
MULTIPLE METRICS N Caliskan*, E Jadraqueo, Y Tham** and T Muneer**
* Istanbul Technical University, Turkey o Department of Civil Engineering, University of Granada, Spain
** School of Engineering and Built Environment, Edinburgh Napier University, Scotland, UK
Abstract
Engineering practise heavily relies on the development and use of mathematical
models. In this article a number of appropriate metrics have been selected to provide
an insight in the validation of models and also to obtain a ‘figure of merit’ for any
given model. The latter exercise enables categorisation of models with respect to their
performance if more than one model is available, or developed, for any given task. A
Microsoft Excel/Visual Basic for Applications software has been expressly developed
for the latter task that enables automation of the model validation work. This software
product is provided on this research team’s website. The reader may download this
shareware-software as an open access tool. © 2011 Published by Elsevier B.V.
Key words: mathematical modelling, automobile emissions, statistical models
Nomenclature MAD mean absolute deviation MBE mean bias error NDMAD non-dimensional mean absolute deviation NDMBE non-dimensional mean bias error NDRMSE non-dimensional root mean square error r correlation coefficient RMSE root mean square error s slope of the best-fit line Yc computed value of the dependent variable Ym measured or observed value of the dependent variable Greek letter Ψ figure of merit 2210-6707/$ – see front matter © 2011 Published by Elsevier B.V.
doi:10.1016/j.scs.2011.02.001
N Caliskan et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 153
1 INTRODUCTION
In engineering research, development of mathematical models is common
practise. Of equal importance is the work related to checking the adequacy of those
models. It is common practise to develop models wherein one dependent variable is
regressed against one or several independent variables. Often correlation between two
quantities also needs to be examined. In some of the engineering literature it has
become common practise to refer regression models as ‘Correlation Equations’.
Strictly speaking this is wrong usage of statistician’s language. Correlation is the
degree of relationship between variables and one seeks to determine how well a linear
or other model describes the relationship. On the other hand, regression is a technique
of fitting linear or non-linear models between a dependent and a set of independent
variables. In this brief note an attempt has been made to bring together a number of
statistical metrics that ought to help researchers in their mathematical model
validation work. The aim of this note is to: (i) provide a number of carefully chosen
metrics to provide an insight in model’s evaluation, (ii) to obtain a ‘figure of merit’
for any given model thus enabling categorisation of models with respect to their
performance if more than one model is available, or developed, for any given task,
and (iii) provide an open source Microsoft Excel/Visual Basic for Applications
software that enables the reader to automate the task of model validation.
2 ANALYSIS
The following statistical parameters are used in the section below to quantitatively
evaluate the performance of each function presently used.
2.1 Slope of the best-fit line, s
The slope of the best-fit line, given by Eq. (1), between the computed and
measured variable is desired to be as close as possible to unity. Slope values
exceeding one indicate overestimation, while slope values under one indicate
underestimation of the computed variable.
Anexo: Evaluation of the accuracy of mathematical models through use of multiple metrics
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 154
( )( )( )∑
∑−
−−= 2
mm
ccmm
YY
YYYYs (1)
Note that Yc is the calculated value of the dependent variable and Ym is the
measured or observed value, and mY is the mean value of the measured variable.
2.2 Coefficient of determination, r2
The coefficient of determination (r2) is the ratio of explained variation to the total
variation. r2 lies between zero and one.
( )( )( ) ( )
2
22
2
⎥⎥
⎦
⎤
⎢⎢
⎣
⎡
−−
−−=
∑∑∑
ccmm
ccmm
YYYY
YYYYr (2)
A high value of r2, thus indicating a lower unexplained variation, is desirable. r2 is
often used to judge the adequacy of a regression model, but it should not be the sole
criterion for choosing a particular model. In the present context r2 provides an
indication of the order of scatter between Yc and Ym. Further information may be
obtained in Draper and Smith (1998) and Montgomery and Peck (1992).
2.3 Root mean squared error, RMSE
The root mean squared error (RMSE) gives a value of the level of scatter that the
model produces. This is an important statistical test as it highlights the readability and
repeatability of the model. It provides a term-by-term comparison of the actual
deviation between the predicted and the measured values. Since it is a measure of the
absolute deviation, RMSE is always positive. A lower absolute value of RMSE
indicates a better model. Mathematically, it is given by the following equation:
( )∑ ⎥⎦⎤
⎢⎣⎡ −
=2
nYYRMSE mc (3)
N Caliskan et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 155
2.4 Mean bias error, MBE
The mean bias error (MBE) provides an indication of the trend of the model,
whether it has a tendency to underpredict or overpredict the modeled values. MBE
can be expressed either as a percentage or as an absolute value. Nevertheless, within a
data set an overestimation of one observation can cancel an underestimation of
another. A MBE nearest to zero is desired. It is given by the following equation:
( )n
YYMBE mc∑ −
= (4)
2.5 Mean of absolute deviations, MAD
Another metric that is often employed in such analysis is the mean of absolute
deviations, MAD and is given by,
nYY
MAD mc∑ −= (5)
Unlike MBE, the MAD metric provides an insight into the scatter between Yc and
Ym. Note that the MAD is similar to RMSE and provides a measure of absolute
deviations.
2.6 Non-dimensional MBE, MAD and RMSE
The above formulae provide MBE, MAD and RMSE, which have the same
physical units as the dependent variable, Y. In some instances non-dimensional MBE
(NDMBE), MAD (NDMAD) and RMSE (NDRMSE) are required. These are
obtained as follows,
( )
nY
YY
NDMBE m
mc∑ ⎥⎦
⎤⎢⎣
⎡ −
= (6)
Anexo: Evaluation of the accuracy of mathematical models through use of multiple metrics
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 156
( )
nY
YY
NDMAD m
mc∑ ⎥⎦
⎤⎢⎣
⎡ −
= (7)
( )
nY
YY
NDRMSE m
mc∑ ⎥⎦
⎤⎢⎣
⎡ −
=
2
(8)
Figure 1. Basic concepts for the statistical parameters that were presently used. (a): Slope has a large
deviation but with a reduced data scatter about the fitted line. (b) Slope is very close to ideal value but
with an enhanced data scatter. (c) Smaller but a systematic trend of deviations. (d) An almost equal
spread of positive and negative but larger deviations.
N Caliskan et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 157
RW VA DA T WS ES Pollution level
6.2 2 67 314 5.4 1.2 17.2 3.3 1 66 313 5.3 1.0 18.4 3.3 1 54 301 4.1 1.0 18.7 6.2 2 55 302 4.2 1.2 17.9 3.3 1 42 289 2.9 1.0 19.2 6.2 2 43 290 3.0 1.2 19.2 3.3 1 30 277 1.7 1.0 20.5 6.2 2 31 278 1.8 1.2 21.5 7.5 3 68 315 5.5 1.4 21.6 7.5 3 56 303 4.3 1.4 23.2 7.5 3 44 291 3.1 1.4 25.5
10.5 4 69 265 5.6 1.6 28.0 7.5 3 32 279 1.9 1.4 29.7 3.3 1 18 265 0.5 1.0 33.6 6.2 2 19 266 0.6 1.2 33.1
10.5 4 57 304 4.4 1.6 30.7 10.5 4 45 292 3.2 1.6 34.6
7.5 7 60 307 4.7 1.0 38.1 7.5 3 20 267 0.7 1.4 42.4
RW VA DA T WS ES Pollution
level 10.5 8 25 272 1.2 1.2 86.9
6.2 10 63 310 5.0 1.6 89.9 3.3 9 38 285 2.5 1.4 97.8
10.5 8 20 269 6.0 1.2 97.2 6.2 10 51 298 3.8 1.6 102.4 6.2 6 23 270 1.0 2.0 111.1 7.5 11 64 311 5.1 1.8 113.2 6.2 10 39 286 2.6 1.6 121.2 3.3 9 26 273 1.3 1.4 123.7 6.2 6 18 267 5.8 2.0 125.5 7.5 11 52 299 3.9 1.8 129.2
10.5 12 65 312 5.2 2.0 139.8 7.5 11 40 287 2.7 1.8 153.2 6.2 10 27 274 1.4 1.6 154.4
10.5 12 53 300 4.0 2.0 159.9 10.5 12 41 288 2.8 2.0 189.7
7.5 11 28 275 1.5 1.8 194.4 10.5 12 29 276 1.6 2.0 240.0
Table 1. Automobile fleet mix and pollution level for a Scottish city. RW: Road Width (m), VA:
Vehicle Age (years), DA: Driver Age (years), T: Temperature (K), WS: Wind Speed (m/s), ES: Engine
Capacity (l), Pollution Level: nitrogen dioxide concentration (µg /m3).
RW VA DA T WS ES Pollution level
10.5 4 33 280 2.0 1.6 41.2 7.5 7 48 295 3.5 1.0 42.7 3.3 5 70 266 5.7 1.8 46.3 3.3 5 58 305 4.5 1.8 50.5 7.5 7 36 283 2.3 1.0 50.1
10.5 8 61 308 4.8 1.2 49.8 3.3 5 46 293 3.3 1.8 56.6
10.5 4 21 268 0.8 1.6 57.2 10.5 8 49 296 3.6 1.2 56.6
6.2 6 59 306 4.6 2.0 61.8 7.5 7 24 271 1.1 1.0 64.9 3.3 5 34 281 2.1 1.8 66.3
10.5 8 37 284 2.4 1.2 67.1 6.2 6 47 294 3.4 2.0 70.4 7.5 7 19 268 5.9 1.0 71.1 3.3 9 62 309 4.9 1.4 74.0 3.3 9 50 297 3.7 1.4 83.4 6.2 6 35 282 2.2 2.0 84.1 3.3 5 22 269 0.9 1.8 87.1
Anexo: Evaluation of the accuracy of mathematical models through use of multiple metrics
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 158
2.7 Figure of merit, Ψ
One of the important steps in the evaluation of different functions is the
interpretation of different statistical parameters, namely, slope, r2, MBE, MAD and
RMSE. Often when two or more models are inter-compared for their relative strengths
and weaknesses there may be a tie between the above-mentioned metrics. For
example a model may have a lower MBE but a higher RMSE. Therefore, an overall
accuracy score is highly desirable to facilitate a discrete comparison between different
models. In the present article, a novel statistical tool that combines the five metrics
mentioned above to produce an overall score. With the view to demonstrate this point
Fig. 1(a) shows a slope that has a large deviation from the ideally sought value of 1
but a high value of r2, whereas in Fig. 1(b) the slope is very close to the ideal value,
but a low value of r2 is realized due to large data scatter. Therefore case (b) would be
preferable over case (a). Similarly, Fig. 1(c) presents a smaller but systematic trend of
deviation -notice the negative deviations in the middle range, with positive outcomes
at the lower and higher ends. In the case of Fig. 1(d), an almost equal spread of
positive and negative but larger deviations is noticed. Although case (d) would
provide a much higher value of MBE, case (d) would, however, be preferable over
case (c). Overall, it can be concluded that the slope parameter provides a much more
important indication of the validity of any given model. The r2 of the line fitted
between computed and observed data, MBE, MAD and RMSE for the given model’s
deviation provide second order information as higher values of r2 or lower values of
MBE, MAD and RMSE do not warrant a better model. Ideally, the latter four
parameters ought to be examined in conjunction with the value of slope. The
following overall accuracy score is proposed with varying weighting factors of 3, 1, 1,
1 and 1 for s, r, RMSE, MBE and MAD respectively:
[ ] [ ] ⎥⎦
⎤⎢⎣
⎡−+
⎥⎥⎦
⎤
⎢⎢⎣
⎡−+⎥
⎦
⎤⎢⎣
⎡−++=
maxmaxmax
1113MAD
MADMBE
MBERMSE
RMSErsψ (9)
Note that s and r are dimensionless, unlike RMSE, MBE and MAD, and therefore
the latter three are respectively divided by the values of RMSEmax, │MBE│max and
MADmax. Ψ is a convenient figure of merit, by means of which it is possible to
N Caliskan et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 159
compare the performance of any suite of models. Therefore, for a perfect fit the
overall accuracy score Ψ will be 7.
Model 1:
111111 )(*)(*)(*)(*)(*)(*1fedcba WSTESDAVARWK
K1 799.9660496
a1 -0.282693012
b1 0.596283499
c1 -0.240567364
d1 -0.288961898
e1 -0.775288994
f1 0.584117699
Model 2: 222222 )(*)(*)(*)(*)(*)(* 262524232221
fedcba WSKTKESKDAKVAKRWK +++++
K21 72.9877178
K22 0.15746905
K23 387.4612945
K24 2.092969749
K25 9.82933495
K26 -111.1774902
a2 -1.891875639
b2 2.705221091
c2 -0.320569166
d2 -10.21628577
e2 -0.05759274
f2 4.397934314
Table 2. Coefficients used in models 1 and 2.
3 EXAMPLE
The latest UK air quality objectives for protection of human health were published
in July 2007. These standards demand that the inner city nitrogen dioxide hourly
Anexo: Evaluation of the accuracy of mathematical models through use of multiple metrics
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 160
mean pollution resulting from vehicular traffic and other sources does not exceed 200
µg m-3 for more than 18 times a year (AEA, 2010). The chief contributor to Nitrogen
Dioxide (NO2) within inner cities is the automobiles’ internal combustion engine
which produces nitric oxide (NO) when a rich mixture of fuel and air is used. nitric
oxide (NO) is a molecule with momentous biological functions but very simple
structure. It carries an unpaired electron behaving as a free radical that avidly reacts
with other molecules. It has lipid solubility and disappears quickly in the presence of
oxygen, with a half life of about three seconds. NO undergoes rapid oxidation to NO2
which is the prevalent in the atmosphere. The effects of NO2 on human health focus
mainly on the respiratory system.
Data
points MAD NDMAD MBE NDMBE RMSE NDRMSE slope r ψ
56 5.459 0.096 -0.956 0.000 7.716 0.126 0.977 0.989 4.600 56 7.849 0.130 -0.685 -0.002 12.336 0.192 0.922 0.971 4.022
Table 3. Evaluation of the performance of models 1 and 2 using presently proposed scheme.
Table 1 shows data collected for one city in Scotland on the automobile fleet mix
passing a city centre location during a short duration of time and the consequent NO2
concentration. Two teams of researchers have attempted to develop mathematical
models to relate the NO2 concentration to the independent parameters that are provide
in Table 1, i.e. road width, vehicle age, driver age, temperature, wind speed and
engine capacity.
The formulations proposed by the above two teams are given below:
111111 )(*)(*)(*)(*)(*)(*1 1
fedcba WSTESDAVARWKModel = (Model 1)
222222 )(*)(*)(*)(*)(*)(*2 262524232221fedcba WSKTKESKDAKVAKRWKModel +++++= (Model 2)
Use the analysis provided in Section 2 above to evaluate the above two formulations
with the view to identify the better model.
N Caliskan et al., 2011
The use of photovoltaic solar energy as an energy source in the residential housing sector 161
3.1 Solution
Respectively using the solver facility available in Microsoft Excel and the
software expressly developed by the present authors Tables 2 and 3 may be obtained.
Note that Table 2 obtained using unconstrained optimisation technique, provides the
best-fit values of the coefficients shown in Models 1 and 2. Table 3 was obtained via
use of the presently developed code that is available from this website:
http://www.etresh.eu/downloads.htm.
Note that within Table 3 the MBE for Model 1 is higher, though all other metrics
show a better performance. The overall score for Model 1 is higher indicating its
overall better performance.
REFERENCES
[1] Draper, N., & Smith, H. (1998). Applied regression analysis. New York:
Wiley.
[2] Montgomery, D., & and Peck, E. (1992). Introduction to linear regression
analysis. New York: Wiley.
[3] AEA (2010) UK air quality archive: Air quality standards
http://www.airquality.co.uk/standards.php (accessed 10.08.10).
Anexo: Edificación sostenible y eficiencia energética
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 162
ANÁLISIS COMPARATIVO DE TRES MODELOS DE
ESTIMACIÓN DEL CONSUMO ENERGÉTICO DE LA
VIVIENDA RESIDENCIAL Jadraque, E.; Ordoñez, J.; Alegre, J.; Martínez, G.
Abstract
Energy certification of buildings is a requirement under Directive 2002/91/EC.
Regarding energy certification, partially transposing this directive into Spanish law
through Royal Decree 47/2007 of January 19, which approves the basic procedure for
the certification of energy efficiency of new buildings. This article analyzes and
compares three models for estimating energy demand. This study aims to develop an
optimization model of energy consumption in residential buildings in order to identify
potential savings and implement improvement measures to enable more efficient energy
consumption in each building and the identification of potential incorporate energy.
Keywords: Energy certification, Energy efficiency, Energy consumption
Resumen
La Certificación Energética de los Edificios es una exigencia derivada de la Directiva
2002/91/CE. En lo referente a la certificación energética, esta Directiva se transpone
parcialmente al ordenamiento jurídico español a través del Real Decreto 47/2007, de 19
de enero, por el que se aprueba el Procedimiento básico para la certificación de
eficiencia energética de edificios de nueva construcción. El presente artículo analiza y
compara tres modelos de estimación de la demanda de energía. Este estudio tiene como
finalidad el desarrollo de un modelo de optimización del consumo energético en los
edificios residenciales con el fin de identificar potenciales ahorros y llevar a cabo
medidas de mejora que permitan eficientizar el consumo de energía en cada edificio así
como la identificación del potencial de incorporar energías.
Palabras clave: Certificación energética, Eficiencia energética, Consumo energético,
Sector residencial
Jadraque, E. et al., 2009
The use of photovoltaic solar energy as an energy source in the residential housing sector 163
1 INTRODUCCIÓN
La edificación en Europa, representa más del 40 % del consumo final de energía de
los Estados miembros de la Unión Europea (UE), de los cuales el uso residencial
representa el 63 % del consumo total de energía. En consecuencia, un aumento en las
políticas encaminadas a la construcción de edificios energéticamente eficientes podría
constituir un importante instrumento en los esfuerzos para aliviar la dependencia de las
importaciones de energía de los países que constituyen la UE (actualmente en torno al
48 %) y cumplir con el Protocolo de Kyoto para reducir las emisiones de dióxido de
carbono [1,2]. Todo ello dentro de las exigencias marcadas por la Directiva 2002/91/CE
relativa a la eficiencia energética de los edificios [3].
Por otro lado, la insostenibilidad del actual modelo de producción-consumo de
energía pone de manifiesto el carácter limitado de los recursos energéticos
convencionales, así como la degradación del medio ambiente resultado de este modelo
[4,5].
Las reservas actuales de petróleo y gas natural solo pueden cubrir el consumo de
energía para los próximos 40 años en el caso del petróleo, y para 60 años en el caso
del gas natural [5].
El aumento del uso y promoción de energías renovables parece una solución viable
para los problemas producidos en el medio ambiente por otras fuentes de energía [2].
Por esta razón, las políticas actuales se centran en fomentar el desarrollo y uso de las
energías renovables en Europa [6].
En España el sector de la edificación residencial consume el 10 % (10.793 ktep.)
del consumo de energía total [7].
En el año 1998 se desarrolló la primera investigación detallada y profunda sobre la
demanda eléctrica en España. Los datos de este proyecto y la descripción de los rasgos
y pautas del uso de la energía eléctrica y su evolución hasta la fecha de inicio del
funcionamiento del mercado de electricidad, el 1 de enero de 1998, quedaron
reflejados en la publicación denominada “Atlas de Demanda Eléctrica Española.
Proyecto INDEL” [8].
La importancia que tiene en el consumo de energía eléctrica la edificación
residencial, justifica el desarrollo de modelos que permitan obtener la estructura por
usos (climatización, electrodomésticos, iluminación, agua caliente sanitaria,…) de
Anexo: Edificación sostenible y eficiencia energética
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 164
dicho consumo. Diversos autores han desarrollado modelos que tienen este objetivo:
Yamaguchi Y et al. [9], Seem JE [10], Al-Mumin A et al. [11], Farinaccio L y
Zmeureanu R [12], Shimoda Y et al. [13].
2 ANÁLISIS DE TRES MODELOS DE CONSUMO DE ENERGÍA EN EL
SECTOR RESIDENCIAL
El consumo de energía del sector residencial, por sus características, es complejo.
Por ello, se necesitan modelos para evaluar el impacto de la adopción de la eficiencia
energética y las tecnologías de energía renovable adecuadas para aplicaciones
residenciales.
Los autores Swan LG y Ugursal VI ofrecen una revisión actualizada de las diversas
técnicas de modelado del consumo de energía en el sector residencial. Esta revisión se
realiza bajo dos enfoques [14]:
1. Descendente: Trata al sector de la vivienda como un sumidero de energía
y no se refiere a los distintos usos finales. Utiliza los valores históricos de la
energía total y retrocede al consumo de energía de las viviendas en función de
variables de nivel superior como los indicadores macroeconómicos (PIB,
desempleo, inflación…), los precios de la energía y el clima (figura 1).
2. Ascendente: Extrapola la estimación del consumo de energía de un
conjunto representativo del sector residencial a nivel regional y nacional, y se
compone de dos tecnologías: el método estadístico y el método de ingeniería.
Cada método se basa en diferentes niveles de entrada de información, de
simulación o técnicas de cálculo deferentes, y proporcionan resultados con
diferentes aplicaciones (figura 1).
Jadraque, E. et al., 2009
The use of photovoltaic solar energy as an energy source in the residential housing sector 165
Consumo Energia Residencial
Descendente Ascendente
Econométrico Tecnologíco Estadístico Ingeniería
Regresión
Condicionado análisis demanda
Redes neuronales
Distribución poblacional
Prototipo
Muestra
Figura 1. Técnicas de modelado descendente y ascendente para la estimación regional y nacional del
consumo de energía en el sector residencial [14].
A continuación se analizan tres modelos de consumo de energía residencial, dos de
ellos incluidos en el Atlas de Demanda Eléctrica Española del proyecto INDEL y otro
desarrollado por Shimoda Y et al. [15].
2.1 Atlas de demanda eléctrica española. Proyecto INDEL
El Atlas de la Demanda Eléctrica del proyecto INDEL trata de definir donde se
encuentran las claves de evolución de la demanda. Analizando la demanda del sector
residencial, el Atlas parte de la información aportada por una muestra de consumidores
compuesta por 1.500 hogares principales, representativos de la población peninsular, y
que han aportado información sobre su consumo, equipamiento y uso de la energía
desde 1988 [8].
Su consumo horario se midió mediante un sistema constituido por equipos
registradores de potencia durante el periodo 1991-1997. El número de hogares
colaboradores con el Proyecto fue de 5.467. Por medio de un cuestionario se realizo una
segmentación de la población española según estilos de vida y se hizo un estudio de las
actitudes y conductas respecto al medio ambiente y el consumo energético de los
diferentes grupos [8]. Las conclusiones se lograron aplicando dos metodologías de
análisis matemático:
Anexo: Edificación sostenible y eficiencia energética
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 166
1. Análisis de la Evolución.
2. Explicación de la Curva de Carga por Usos.
Estas metodologías de análisis de la demanda de energía se engloban dentro de los
métodos ascendentes estadísticos, clasificados a su vez en modelos de regresión,
condicionados al análisis de la demanda y neuronales [14], y han sido desarrollados por
diversos autores Hirst E et al. [16], Raffio G et al. [17], Parti M y Parti C [18], Aigner
DJ et al [19], Caves DW et al [20], Kreider JF y Haberl JS [21], Issa RRA et al [22].
La metodología para el Análisis de la Evolución, ayuda a comprender los factores
que influyen en la demanda y prever su comportamiento futuro a medio y largo plazo,
según escenarios económicos y tecnológicos. Mediante la determinación cuantitativa del
impacto de una serie de factores (datos que alimentan el análisis) sobre la demanda de
energía y aplicando la metodología de análisis de la evolución, este modelo predice la
demanda de energía. Se aplica a cualquier serie de demanda mensual de energía, ya sea
la del sistema o la de segmentos de consumidores (figura 2).
Esta metodología abarca 16 modelos estadísticos que incorporan técnicas de
clasificación, tipificación, análisis multivariante, análisis de series temporales y técnicas
de desestacionalización. Transforma las variables exógenas (estadísticas españolas,
indicadores de actividad económica, temperatura, calendarios y equipamiento y/o
sensibilidad a la temperatura por sectores) en indicadores relevantes para el análisis de
la demanda eléctrica. Estima la influencia de los distintos factores sobre la demanda y
su evolución a largo plazo, prediciendo cada factor a corto y largo plazo (figura 2).
Jadraque, E. et al., 2009
The use of photovoltaic solar energy as an energy source in the residential housing sector 167
Datos que Alimentan el Análisis
Demanda Diaria del Sistema de b.c. Peninsular y Balear (Histórico)
Demanda Diaria de Segementos de Consumidores (Histórico)
Temperatura Diaria por Zonas (Historico y Previsto)
Indicadores Mensuales Actividad Económica (Histórico y Previsto)
Calendarios por Zonas (Histórico y Previsto)
Resultados
Influencia de la Temperatura
Influencia de la Laboralidad
Influencia de la Actividad Económica
Estacionalidad Mensual
Evolución Coyuntural
Evolución Tendencial
Metodología
Estima la Evolución de la Demanda por sus
factores Explicativos
Estima el cambio de la influencia de los Factores en el largo plazo
Prevé la evolución
futura
Figura 2. Metodología de análisis de demanda de energía mediante el análisis. Fuente: Proyecto INDEL.
Atlas de la Demanda Eléctrica Española. Programa de Investigación y Desarrollo Electrotécnico (PIE).
Red Eléctrica de España.
Como aplicación de esta metodología, se analiza a continuación la influencia de la
temperatura en la evolución de la demanda residencial.
0
1000
2000
3000
4000
5000
6000
88 89 90 91 92 93 94 95 96 97
Entretiempo
TotalInvierno
Datos provisionales
Años
GWh
Figura 3. Influencia de la temperatura en la demanda residencial. Fuente: Proyecto INDEL. Atlas de la
Demanda Eléctrica Española. Programa de Investigación y Desarrollo Electrotécnico (PIE). Red Eléctrica
de España.
La temperatura es la causa principal del cambio de la demanda en los hogares. Su
efecto, 4.570 GWh de media en el periodo 1989-1996, supone el 18 % de la demanda
total residencial [8]. La mayor parte de este efecto se concentra en los meses de
Anexo: Edificación sostenible y eficiencia energética
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 168
invierno, diciembre, enero y febrero, 3.140 GWh. Supone un 12.2 % de la demanda
total para el mismo periodo. En el periodo de entretiempo, noviembre, marzo y abril, la
influencia es mucho menor: 5.5 % de la demanda (figura 3).
La metodología de Explicación de la Curva de Carga por Usos, se compone de 24
modelos estadístico-matemáticos y de simulación que incorporan técnicas de
clasificación, tipificación de formas, análisis multivariante, análisis y proyección de
series temporales y proyección demográfica. Estos modelos, transforman los datos
medidos de curva de carga, procesos de uso y características de los consumidores en
factores relevantes que alimentan el análisis, construyen el consumo horario de cada uso
en cada tipo de día, en base a características encuestadas al consumidor, realizan una
estimación simultánea de la influencia de estos factores sobre la curva de carga
registrada a cada consumidor y sobre un segmento o sector de consumidores y por
último, proyectan a corto y largo plazo la evolución de cada uso basándose en
escenarios tecnológicos, demográficos o económicos, obteniendo la curva de carga
demandada por usos de un sector o segmento de consumidores (figura 4).
Datos que Alimentan el Análisis
Demanda Horaria Registrada Consumidor a Consumidor
Consumos Especificos de Equipos Cur vas de Carga Medidas
Horarios, Intensidas y Frecuencias de Usos
Consumidor a Consumidor
Características Económicas y Sociales Consumidor a
Consumidor
Temperatura, Calendario y otras Variables Exógenas
Metodología
Reparte la Curva de carga entre los Usos
Identifica las Características de los Consumidores que
discriminan la forma de Uso
Estima la Influencia de la Tempertura en los Usos Térmicos
Resultados
Explicación por Usos de Consumos Horarios por
Tipos de Días
Consumos por usos según Tecnología y Formas de Uso
Tipología de Consumidores por las
variables Discriminantes de su Forma de Uso
Figura 4. Metodología de Explicación de la Curva de Carga por Usos. Fuente: Proyecto INDEL. Atlas de
la Demanda Eléctrica Española. Programa de Investigación y Desarrollo Electrotécnico (PIE). Red
Eléctrica de España.
Aplicando la metodología descrita arriba, se obtiene la figura 5 y la figura 6. La
figura 5 representa la explicación por usos del consumo anual residencial. Se puede ver
que los usos de mayor peso tienen son el frigorífico, televisión, iluminación y pequeños
Jadraque, E. et al., 2009
The use of photovoltaic solar energy as an energy source in the residential housing sector 169
electrodomésticos. El consumo del frigorífico supone un 27.3 % de la demanda
residencial, la iluminación el 23.5 % y la televisión aporta el 12 %. A pesar de que
prácticamente toda la población posee lavadora, ésta supone tan solo el 5 % del
consumo total residencial, pues su uso no es continuo a lo largo del día. El consumo por
calefacción eléctrica es del 10 % de esta demanda.
0
5
10
15
20
25
30
88 89 90 91 92 93 94 95 96 97
Aire Acondicionado Calefacción Secadora Lavadora Lavavajillas Cocina
Iluminación Miscelánea Agua Caliente Congelador Frigorífico
TWh
Años
Estimación provisional
Figura 5. Explicación por usos del consumo anual residencial. Fuente: Proyecto INDEL. Atlas de la
Demanda Eléctrica Española. Programa de Investigación y Desarrollo Electrotécnico (PIE). Red Eléctrica
de España.
0
50
100
150
200
250
300
350
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Calefacción Secadora Lavadora Televisión Lavavajillas Cocina Horno
Iluminación Miscelánea Agua Caliente Congelador Frigorífico
W
Horas
Figura 6. Curva de carga del hogar medio en un día tipo laborable. Fuente: Proyecto INDEL. Atlas de la
Demanda Eléctrica Española. Programa de Investigación y Desarrollo Electrotécnico (PIE). Red Eléctrica
de España.
En la figura 6, se aprecia que la curva de carga del sector residencial tiene su punta
de 21 a 22 horas, momento de mayor ocupación en el hogar. La lavadora y la secadora
Anexo: Edificación sostenible y eficiencia energética
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 170
concentran su consumo durante las mañanas. A las 12 horas, estos dos usos suponen el
21 % de la demanda total residencial. Durante la noche existe otra punta de consumo de
lavadora y secadora consecuencia del trabajo fuera de casa de los componentes
principales de un número de hogares. El agua caliente tiene dos puntas claras, a las 9 de
la mañana y a las 5 de la tarde, que coinciden con el aseo matinal y el fregado de vajilla
posterior a la comida.
Los usos relacionados con la comida en el hogar, cocina y horno, concentran su
consumo en las horas previas a la comida, 2 de la tarde, y cena, en menor medida, a las
9 de la noche.
El lavavajillas tiene sus puntas de consumo en las horas posteriores a dichos
momentos, de comida y cena, es decir, hacia las 16 y 22 horas.
Iluminación, calefacción y televisión mantienen un perfil que coinciden con los
niveles de ocupación de los hogares. El frigorífico y congelador mantienen el mismo
nivel de consumo a lo largo del día, al no desconectarse en ningún momento.
2.2 Residential end-use energy simulation at city scale [15]
Según la clasificación establecida por Swan LG y Ugursal VI [14], este modelo de
estimación de la demanda de energía es un método ascendente, de ingeniería y de
diseño de prototipos.
Los modelos de ingeniería estiman el consumo de energía de los usos finales, en
función de sus calificaciones y características. Estos modelos pueden determinar
plenamente el consumo de energía del sector, sin necesidad de recurrir a información
estadística (al contrario que los dos modelos analizados anteriormente, que si que
partían de datos históricos). La metodología de diseño de prototipos, se utiliza para
clasificar las viviendas de acuerdo a determinados factores (tamaño, tipo de casa, etc.).
A partir de estas variables incluidas en las ecuaciones del modelo, se obtiene la
demanda de energía.
Las estimaciones del consumo de energía obtenidas del modelo se escalan para que
sean representativas del consumo regional o nacional de viviendas, multiplicando el
resultado por el número de viviendas que se ajustan a la descripción de cada prototipo.
MacGregor WA et al [23], Kohler N et al [24], Huang Y et al [25], han sido algunos
de los autores que han desarrollado modelos de demanda de energía de estas
características.
Jadraque, E. et al., 2009
The use of photovoltaic solar energy as an energy source in the residential housing sector 171
La metodología objeto de este análisis, permite desarrollar un modelo de simulación
para predecir el uso final de consumo de energía en sectores residenciales de una ciudad
y región. En este modelo, el consumo anual de energía de una vivienda es simulado a
través del calendario de las actividades de sus ocupantes (mediante encuestas), datos
meteorológicos y la eficiencia energética de los aparatos y de las viviendas. El total de
la energía consumida para el sector de la vivienda en una región puede ser estimado
utilizando los resultados de la simulación para las diferentes categorías de hogares. El
uso de la energía de las viviendas se calcula iterativamente para 23 tipos de hogares y
20 tipos de vivienda (10 viviendas aisladas y 10 bloques). Multiplicando el consumo de
energía simulado por el número de hogares de cada tipología se obtiene el consumo
total de energía para el sector residencial en la región objeto del estudio.
0
100
200
300
400
500
600
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Otros Televisión Secadora Agua Caliente Cocina Frigorífico
W
Horas
Figura 7. Consumo por hora simulado de electricidad por usos en un día tipo laborable [15].
3 RESULTADOS
Aplicando los modelos analizados y desarrollados en el Altas de la Demanda
Eléctrica Española, se obtiene los siguientes consumos anuales de energía en España
para la serie de años 1989-1996:
Anexo: Edificación sostenible y eficiencia energética
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 172
22.500
23.000
23.500
24.000
24.500
25.000
25.500
26.000
26.500
27.000
1989 1990 1991 1992 1993 1994 1995 1996
GWh
Figura 8. Consumo anual residencial. Fuente: Proyecto INDEL. Atlas de la Demanda Eléctrica Española.
Programa de Investigación y Desarrollo Electrotécnico (PIE). Red Eléctrica de España.
La demanda eléctrica anual de los hogares se estima en 25.768 GWh/año, como
promedio, en el periodo analizado.
16.000 9.00010.500
34.000
26.000
44.00029.500
46.000
39.000
32.000
11.000
Consumo de energíaestimado por hogar
Valor estadístico delconsumo de energía
Consumo total deenergía estimado a
partir de lasimulación
Miscelanea Iluminación Cocina
Agua Caliente Calefacción Refrigeración
TJ/a
ño
Figura 9. Consumo total de energía del sector residencial en la ciudad de Osaka (Japón) [15].
La figura 8, representa el consumo total de energía del sector residencial en la
ciudad de Osaka (Japón), calculado a partir de la simulación, el valor estadístico del
consumo de energía en el año de referencia 1999 y la estimación de los valores
derivados del producto entre el número total de hogares en la ciudad analizada y el
Jadraque, E. et al., 2009
The use of photovoltaic solar energy as an energy source in the residential housing sector 173
consumo de energía estimado por hogar. Se obtiene que el consumo total de energía
calculado, a partir de la simulación es 32.018 TJ/año.
Comparando las curvas de carga (figura 10 y 11), hay que señalar como
características comunes, que los distintos modelos analizados, tienen en cuenta como se
distribuyen las distintas tipologías de viviendas y hogares en la región de estudio.
Los modelos analizan el efecto del cambio de estilo de vida en el consumo de
energía, ya que el uso de aparatos con consumo energético está vinculado a las
actividades cotidianas de los ocupantes del hogar.
En cada unos de los modelos, se obtiene una distribución del consumo por hora de
electricidad por usos distinta, condicionada por la diferencia entre unas regiones y otras
en aspectos tales como: tamaño y tipología de las viviendas, calendario de actividades
de sus ocupantes, eficiencia energética de los aparatos y viviendas, datos
meteorológicos, etc.
0
500
1000
1500
2000
2500
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Frigoríf ico Cocina Agua Caliente Secadora Televisión Otros
W
Horas
Figura 10. Curva de carga del hogar medio en un día tipo laborable. Fuente: Proyecto INDEL. Atlas de la
Demanda Eléctrica Española. Programa de Investigación y Desarrollo Electrotécnico (PIE). Red Eléctrica
de España.
Anexo: Edificación sostenible y eficiencia energética
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 174
0
100
200
300
400
500
600
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Otros Televisión Secadora Agua Caliente Cocina Frigorífico
W
Horas
Figura 11. Consumo por hora simulado de electricidad por usos en un día tipo laborable [15].
4 CONCLUSIONES
La importancia que tiene en el consumo de energía eléctrica la edificación
residencial, justifica el desarrollo de modelos que permitan obtener la estructura por
usos (climatización, electrodomésticos, iluminación, agua caliente sanitaria,…) de dicho
consumo.
El desarrollo de modelos energéticos puede desempeñar una función primordial a la
hora de evaluar el efecto de políticas destinadas a la conservación de la energía y el
impacto que ocasionarían cambios en la eficiencia energética de los aparatos de
consumo eléctrico.
Por último, conociendo el consumo energético de una vivienda, estos modelos
permitirían evaluar el efecto provocado, en dicho consumo, por modificaciones en el
aislamiento térmico.
REFERENCIAS
[1] Dincer I. Renewable energy and sustainable development: a crucial review.
Renew Sust Energy Rev 2000;4:57–75.
[2] Martinez G, Serrano MM, Rubio MC, Menendez A. An overview of renewable
energy in Spain. The small hydro-power case. Renew Sustain Energy Rev 2005;9:521–
34.
Jadraque, E. et al., 2009
The use of photovoltaic solar energy as an energy source in the residential housing sector 175
[3] Balaras CA, Gaglia AG, Georgopoulou E, Mirasgedis S, Sarafidis Y, Lalas DP.
European residential buildings and empirical assessment of the Hellenic building stock,
energy consumption, emissions and potential energy savings. Building and Environment
2007;42:1298-1314.
[4] Xiaowu W, Ben H. Energy analysis of domestic-scale solar water heaters.
Renewable and Sustainable Energy Reviews 2005;639–45.
[5] Jefferson M. Sustainable energy development: performance and prospects.
Renewable Energy 2006;31:571–82.
[6] Ordóñez GJ, Gago EJ, Bayo JA, Montes GM. The use of solar energy in the
building construction sector in Spain. Renewable and Sustainable Energy Reviews
2007;11:2166–78.
[7] IDAE, Estrategia de ahorro y eficiencia energética en España 2004–2012. Plan
de acción 2008–2012. Ministerio de Industria, Turismo y Comercio, Instituto para la
Diversificación y Ahorro de la Energía, 2007.
[8] Proyecto INDEL. Atlas de la Demanda Eléctrica Española. Programa de
Investigación y Desarrollo Electrotécnico (PIE). Red Eléctrica de España.
[9] Yamaguchi Y, Shimoda Y, Mizuno M. Proposal of a modelling approach
considering urban form for evaluation of city level energy management, Energy and
Buildings 2007;39:580–592.
[10] Seem JE. Pattern recognition algorithm for determining days of the week with
similar energy consumption profiles, Energy and Buildings 2005;37:127–139.
[11] Al-Mumin A, Khattab O, Sridhar G. Occupants behaviour and activity patterns
influencing the energy consumption in the Kuwaiti residences, Energy and Buildings
2003;35:549–559.
[12] Farinaccio L, Zmeureanu R. Using a pattern recognition approach to
disaggregate the total electricity consumption in a house into the major end-uses,
Energy and Buildings 1999;30:245–259.
[13] Shimoda Y, Asahi T, Taniguchi A, Mizuno M. Evaluation of city-scale impact
of residential energy conservation measures using the detailed end-use simulation
model. Energy 2007;32:1617-1633.
[14] Swan LG, Ugursal VI. Modelling of end-use energy consumption in the
residential sector. A review of modelling techniques. Renewable and Sustainable
Energy Reviews 2009;13:1819–1835.
Anexo: Edificación sostenible y eficiencia energética
Uso de la energía solar fotovoltaica como fuente para el suministro de energía eléctrica en el sector
residencial 176
[15] Shimoda Y, Fujii T, Morikawa M, Mizuno M. Residential end-use energy
simulation at city scale. Building and Environment 2004;39(8):959–67.
[16] Hirst E, Goeltz R, White D. Determination of household energy using
“fingerprints” from energy billing data. Energy Research 1986;10(4):393–405.
[17] Raffio G, Isambert O, Mertz G, Schreier C, Kissock K. Targeting residential
energy assistance. In: Proceedings of energy sustainability conference; 2007. p. 489–95.
[18] Parti M, Parti C. The total and appliance-speci c conditional demand for
electricity in the household sector. The Bell Journal of Economics 1980;11(1):309–21.
[19] Aigner DJ, Sorooshian C, Kerwin P. Conditional demand analysis for
estimating residential end-use load profiles. The Energy Journal 1984;5(3):81–97.
[20] Caves DW, Herriges JA, Train KE, Windle R. A Bayesian approach to
combining conditional demand and engineering models of electricity usage. The
Review of Economics and Statistics 1987;69(3):438–48.
[21] Kreider JF, Haberl JS. Predicting hourly building energy use: the great energy
predictor shootout—overview and discussion of results. ASHRAE Transactions 1994;
100(2):1104–18.
[22] Issa RRA, Flood I, Asmus M. Development of a neural network to predict
residential energy consumption. In: Proceedings of the sixth international conference on
the application of artificial intelligence to civil & structural engineering computing;
2001. p. 65–6.
[23] MacGregor WA, Hamdullahpur F, Ugursal VI. Space heating using small-scale
fluidized beds: a technoeconomic evaluation. International Journal of Energy Research
1993;17(6):445–66.
[24] Kohler N, Schwaiger B, Barth B, Koch M. Mass .ow, energy .ow and costs of
the German building stock. CIB, 2nd international conference on buildings and the
environment, Paris, France; 1997.
[25] Huang Y, Broderick J. A bottom-up engineering estimate of the aggregate
heating and cooling loads of the entire US building stock. Lawrence Berkeley National
Laboratory, Report LBNL-46303; 2000.