Test Results Summary for Cisco Wireless LAN Controller ... · WLC-License213 AP-GUI215...

Test Results Summary for Cisco Wireless LAN Controller AireOS 8.0,IOS XE 3.6/3.7, for Japan (Release Version AireOS 8.0.100.0,8.0.110.0/IOS XE 03.06.00.E, 03.07.00E )First Published: October 01, 2014

Last Modified: February 05, 2015

Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000 800 553-NETS (6387)Fax: 408 527-0883

Text Part Number:

© 2015 Cisco Systems, Inc. All rights reserved.

C O N T E N T S

C H A P T E R 1 Overview 1

Cisco Wireless LAN Solution Test 1

C H A P T E R 2 Test Topology and Environment Matrix 7

Test Topology 8

Environment Matrix 8

What's New ? 10

Open Caveats 11

Resolved Caveats 12

Limitations 12

C H A P T E R 3 New Features - Test Summary 15

WLC AireOS 15

DHCP Relay Options 15

Show Running Config 24

Flexconnect video streaming 25

Flexconnect Upgrade Time Reduction 28

8500 As Mobility Controller 30

HA Enhancements 40

HTTPS Support 47

NBAR Engine 3.10 - 8.0 51

Rate Limit 56

AAA Override for AVC Profile Name 62

Rf Profile 64

Cleanair-skyros 66

Flexconnect on Mesh 69

Cleanair 70

OEAP Enhancements 70

Test Results Summary for Cisco Wireless LAN Controller AireOS 8.0, IOS XE 3.6/3.7, for Japan (Release VersionAireOS 8.0.100.0, 8.0.110.0/IOS XE 03.06.00.E, 03.07.00E )

iii

L2TPv3 over UDP 78

3700 Autonomous AP 79

11ac CCX Lite 80

MSE 80

CMX Visitor Connect 80

Real-Path 83

Zone Based Analytics 84

CMX NAPP Store 85

702 AP 86

2700 AP 102

C H A P T E R 4 Regression Features - Test Summary 119

WLC AireOS 119

Re-instating PPPoE Modules 119

L2 Security 122

L3 Security 123

Link Aggregation Mode 124

High Availability 125

Roaming 126

AAA 127

Flexconnect Enhancements 128

HREAP 129

Anyconnect VPN 130

Dot1x and Web-Auth Support 131

Multiple RADIUS Server Per SSID 132

Secure FTP 133

NBAR 134

PI 135

NCS Maps 135

Autonomous to LWAPP Migration 135

Backup And Restore of PI 136

PI HA 136

MSE 137

MSE HA 137

SR Test Cases 137


iv

Contents

Fix Verification 142

TAC 147

WLC_Security 154

AP_OEAP 167

WLC_HREAP 169

LWAPP-AP-SW 175

WCM_WEB 176

WLC_Web-auth 177

Alarms_UI 178

Client_Mgmt 178

MSE_Install 179

NCS-MSE 180

WLC-RRM 181

All AP-Radio 190

AP-DFS 192

AP Radio 194

WLC HA 196

Backup - Restore 200

System 201

NCS HA 201

NCS Clean-Air 203

NCS Licensing 203

MSE Software 203

WLC LAN 205

WLC SNMP 205

Maps 206

WLC-Mobility 207

Location 207

WLC Multicast 208

AP-Regulatory 209

WLC DHCP 209

WLC Guestaccess 209

WLC NTP 210

CAPWAP-AP-SW 210

AP-capwap 212


v

Contents

WLC-License 213

AP-GUI 215

Alarm-Server 218

Reports-Wireless 219

WLC-TFTP 220

Prime-UI 221

Admin 223

NCS-Upgrade 223

Reporting 225

AAA 225

AP-HREAP 226

WLC-Web 227

Autonomous_APs 228

Config 228

WLC-Wlan 229

Config-Wireless 229

SR/CFD 230

SR/CFD Test cases 230

NEC 266

Adhoc Test Cases 270

Related Documentation 274


vi

Contents

C H A P T E R 1Overview

• Cisco Wireless LAN Solution Test, page 1

Cisco Wireless LAN Solution TestCisco Wireless LAN Solution Test, an integral part of the enterprise wireless solution, is a program thatvalidates various CiscoWireless Products and Features. This is achieved by testing the latest versions of Ciscowireless products.

Cisco Wireless LAN Solution Test for Japan , in turn is an add-on testing at the solution level, where therequirements gathered are specific to Japanese usage and market. The requirements are derived based on thefollowing:

• New features in 8.0

• Customer found defects in selected wireless products

• High priority scenarios and basic regression features

• Inputs from Cisco SEs/ TAC

The test execution is carried out on selected CiscoWireless LAN products, which affect the Japanese segmentthat are prioritized by Cisco Japan team.

The following products are covered in the test execution:

• Cisco Wireless LAN Controller 5508



• Cisco Wireless LAN Flex Controller 7500

• Cisco Wireless LAN Flex Controller 8500

• Cisco Catalyst 3850 Switch

• WiSM2 Controller

• Virtual Controller


1

• Access Point 3500












• Cisco OEAP 602

• Cisco Prime Network Control System

• Cisco Prime Infrastructure

• ISE Virtual Appliance

• Cisco Secure ACS

• Cisco Mobility Service Engine (MSE )

• Cisco AnyConnect VPN Client

Acronyms

DescriptionAcronym

Authentication Authorization and AccountingAAA

Access Control ListACL

Access Control ServerACS

Authentication Key ManagementAKM

Access PointAP

Application Visibility and Control.AVC

Bring Your Own DeviceBYOD

Central AuthenticationCA

Call Admissions ControlCAC

Control and Provisioning of Wireless Access PointCAPWAP

Cisco Centralized Key ManagementCCKM


2

OverviewCisco Wireless LAN Solution Test

DescriptionAcronym

Cisco Compatible ExtensionsCCX

Cisco Discovery ProtocolCDP

Cisco Key Integrity ProtocolCKIP

Connected Mobile ExperienceCMX

Cisco Vector Beam FormingCVBF

Central Web AuthenticationCWA

Dynamic Channel AssignmentDCA

Demilitarized ZoneDMZ

Domain Name SystemDNS

Delivery Traffic Indication MapDTIM

Differentiated Services Code PointDSCP

Datagram Transport Layer SecurityDTLS

Extensible Authentication ProtocolEAP

End User Licence AgreementEULA

Flex Local AuthenticationFLA

Flex Local SwitchingFLS

Fast TransitionFT

File Transfer ProtocolFTP

Firm WareFW

High AvailabilityHA

Hybrid Remote Edge Access PointH-REAP

Internetwork Operating SystemIOS

Identity Service EngineISE

Link AggregationLAG

Lightweight Extensible Authentication ProtocolLEAP

Location Specific ServicesLSS

Lightweight Access Point ProtocolLWAPP

Modulation Coding SchemeMCS

Management Frame ProtectionMFP

multicast Domain Name SystemmDNS

Message Integrity CheckMIC


3


DescriptionAcronym

Mobility Service EngineMSE

Maximum Transmission UnitMTU

Network Admission ControlNAC

Network Address TranslationNAT

Network Based Application RecognitionNBAR

Network Control SystemNCS

Next Generation Wiring closetNGWC

Network Mobility Services ProtocolNMSP

Office Extended Access PointOEAP

Protected Extensible Authentication ProtocolPEAP

Policy Enforcement ModulePEM

Prime InfrastructurePI

Protected Management FramePMF

Point of InterestPOI

Point-to-Point Protocol over EthernetPPPoE

Pre-shared KeyPSK

Remote Authentication Dial-In User ServiceRADIUS

Redundancy PortRP

Radio Resource ManagementRRM

Simple Object Access ProtocolSOAP

Secure File Transfer Protocol.SFTP

Simple Network Management ProtocolSNMP

Spatial StreamSS

Service Set IdentifierSSID

Single Sign OnSSO

Stateful Switch OverSSO

Terminal Access Controller Access Control SystemTACACS

Transmission Control ProtocolTCP

Trivial File Transfer ProtocolTFTP

Transport Layer SecurityTLS

User Datagram ProtocolUDP


4


DescriptionAcronym

Virtual Wireless LAN ControllervWLC

Virtual Private NetworkVPN

Wired Equivalent PrivacyWEP

Workgroup BridgeWGB

Wireless Intrusion Prevention SystemwIPS

Wireless Service ModuleWiSM

Wireless LANWLAN

Wireless LAN ControllerWLC

Wi-Fi Protected AccessWPA


5



6


C H A P T E R 2Test Topology and Environment Matrix

• Test Topology, page 8

• Environment Matrix, page 8

• What's New ?, page 10

• Open Caveats, page 11

• Resolved Caveats, page 12

• Limitations, page 12


7

Test TopologyFigure 1: Topology In Use

Environment MatrixVersionComponentCategory

8.0.100.0 /8.0.110.0Wireless LAN controller 5508Controller

8.0.100.0 /8.0.110.0Flex Controller 7500

8.0.100.0 /8.0.110.0Wireless LAN Controller 2500

8.0.100.0 /8.0.110.0Wireless LAN Controller 8500

8.0.100.0 /8.0.110.0WiSM2

8.0.100.0 /8.0.110.0Virtual controller

03.06.00.E /3.7.0E (ED)NGWC 5760


8

Test Topology and Environment MatrixTest Topology

VersionComponentCategory

2.1.0.0.87PI (Physical, VM)Application

1.2.0.899ISE(VM)

5.5.0.46Secure ACS (VM)

8.0.100.0MSE (Physical, VM)

10.5.1-10000-7/10.5.1.1000-1(JP)Cisco Unified CommunicationsManager

Call control

15.3Cisco AP 3500Access Point

15.3Cisco AP 3600

15.3Cisco AP 3700

15.3Cisco AP 2600

15.3Cisco AP 2700

15.3Cisco AP 1600

15.3Cisco AP 1262

15.3Cisco OEAP 602

15.3Cisco AP 702I

15.3Cisco AP 702W

15.3Cisco AP 1550

15.3Cisco AP 1530

15.0(2)SE2Cisco 3750V2 switchSwitch

15.1(1)SY1Cisco Cat 6509-E

03.06.00.E /3.7.0E (ED)Cisco Cat 3850

15.13.0.15300, 6300 AGNChipset

7.7Airport Extreme


9

Test Topology and Environment MatrixEnvironment Matrix

VersionComponentCategory

Windows 7 EnterpriseOperating System(JOS)Client

Windows 8 Enterprise

Windows 8.1 Enterprise

Windows XP Professional

Mac OS 10.9.4Apple Mac Book Pro (JP Locale)

iOS 7.1.2(11D257)iPhone 4(JP Locale)

iOS 7.1.2(11D257)iPhone 5(JP Locale)

Android 4.3Samsung Galaxy S-II and S4

1.4.5.3Wireless IP Phone 7921G

1.4.5.3Wireless IP Phone 7925G

1.4.5.3Wireless IP Phones 7926G

Android 4.4NEC LaVie Tab S business

Windows 7 Enterprise/3.1.05178Cisco AnyConnect VPN Client

Apple Mac OS 10.9.4/3.1.05178

Windows 8.1/4.0.00061

Samsung Galaxy S-II/ 3.0.09431

Windows 2008R2EnterpriseADActive Directory

8.9,10IEBrowsers

11.5Opera

30.0Mozilla Firefox

7.0.4Safari

37,40Chrome

What's New ?WLC AireOS

• DHCP Relay Option

• Show Running Config

• Flex: Video Stream Support

• Flex : Upgrade Time Reduction


10

Test Topology and Environment MatrixWhat's New ?

• 8500 Support As MC

• HA Enhancements

• HTTPS Support for Web-Auth

• NBAR Engine

• Rate Limiting Per Client

• AAA Override for AVC Profile Name

• DCA RF Profiles

• Cleanair Express - Skyros

• FlexConnect on Mesh

• Clean Air Support for Xmas Ale Module

• 11ac Module - CCX Lite

• OEAP Enhancements

• L2TPv3 Over UDP

• 3700 Autonomous

MSE

• CMX Visitor Connect

• Real Path

• Zone Based Analytics

• CMX Napp Store

Open CaveatsDefect TitleDefect ID

Page error occurs after applying the config in Vlan mapping pageCSCun59052

Unable to select multiple date option for the Zone analysisCSCun78876

Unable to change MSE Notification Parameter Queue limit in VM machineCSCup77825

Syslog trap level for AP is inconsistent in controllerCSCup82047

Attached Clients count isn't removed from AP radio in WLC CLICSCup87391

MSE HA Failover and failback working inconsistentlyCSCuo56629

Deleted VLAN is showing in Autonomous AP CLI.CSCur00347

AP CLI:show command in non-privileged modeCSCur08583

Creating WLAN profile and SSID names as empty gets accepted in CLICSCur12267


11

Test Topology and Environment MatrixOpen Caveats

Defect TitleDefect ID

Incorrect Username appears after configuring HTTP account in NGWCCSCun55413

OEAP ACL's & Network lists gets deleted after upload/download the configCSCun96815

Unable to block the Hangouts (Gtalk) messenger in AVCCSCus60566

Gmail works in Android Client when Gmail applicationWLC is blocked in AVCCSCus68028

Resolved CaveatsDefect TitleDefect ID

CAS event messages is not triggered correctly for multiple facilityCSCup93585

NMSP status is not consistently activeCSCup21225

Secondary MSE is not active when primary is shutdownCSCum12763

CLI description is missing for module3G in command "config ap ?"CSCup59088

Context Aware notifications are not updated properlyCSCun89585

Device Port Summary dashlet shows wrong info for controllersCSCuo37342

EAP profile name display as Junk character if created in UTF-8 characterCSCuq94587

LED Flash state description is missing in OLH page for All APs detailsCSCuq89168

System Configuration of AP in AP GUICSCuq82767

Custom Webauth and Webauth ACL config in AAPCSCuq93760

GUI: Policy type for "Static WEP" clients is showing as N/ACSCup86941

Some options missing in WLAN>Advanced>Flexconnect in OLH pageCSCum84944

LimitationsDefect TitleDefect ID

Accessibility issue using analytics tabCSCun75576

PI Maps is not synchronized with MSE while copying the exiting MapsCSCun76218

Zone based analytics shows wrong display for multiple zone selectionCSCun78279

Deleted real path is displayed in most popular path analysisCSCun78862

Unable to login PI CLI after changing hostname/IP upon PI re-setupCSCup56865

Export the path outputsCSCuo53852


12

Test Topology and Environment MatrixResolved Caveats


13

Test Topology and Environment MatrixLimitations


14

Test Topology and Environment MatrixLimitations

C H A P T E R 3New Features - Test Summary

• WLC AireOS, page 15

• MSE, page 80

• 702 AP, page 86

• 2700 AP, page 102

WLC AireOS

DHCP Relay OptionsDefectsStatusDescriptionTitleLogical ID

PassedTo check if DHCP relay option82 with link/subnet selectsuboption 5 can be enabled viaCLI in WLC 5500

Configuration ofDHCP Relayoptions - LinkSelect option inWLC 5500

WLJ80S_DHCP_01

PassedTo check if DHCP relay option82 with VPN id /VRF selectsuboption 151 and 152 isenabled via CLI in WLC 5500

Configuration ofDHCP Relayoptions - VPN id orVRF selectionoption in WLC5500

WLJ80S_DHCP_02

PassedTo check if DHCP relayoptions (link/VPN select ) isenabled only when the DHCPproxy is enabled inWLC 5500

DHCP relay options(link/ VPN select )isenabled only whenthe DHCP proxyenabled in WLC5500

WLJ80S_DHCP_03


15

DefectsStatusDescriptionTitleLogical ID

PassedTo check if VPN id or the VRFcan be configured inside VPNselect configuration but notboth together from CLI, UI inWLC 5500

VPN id or the VRFcan be configuredinside VPN selectconfiguration butnot both togetherfrom CLI, UI inWLC 5500

WLJ80S_DHCP_04

PassedTo check if Relay src interfacename configured should be avalid interface present on theWLC 5500

Relay src interfacename should be avalid interfacepresent on theWLC5500

WLJ80S_DHCP_05

PassedTo check if both link select andthe VPN select can be enabledtogether per interface in WLC5500

Link select and theVPN select can beenabled together perinterface in WLC5500

WLJ80S_DHCP_06

PassedTo check if DHCP discoverand request packets are paddedwith the option 82 andsuboption 5 based on Interfaceconfiguration for WLC 5500

DHCP discover andrequest packets arepadded with theoption 82 withsuboption 5 whenlink selectconfigured withininterface for WLC5500

WLJ80S_DHCP_07

PassedTo check if DHCP discoverand request packets are paddedwith the option 82 withsuboption 151 and 152 whenVPN select is configured withthe VPN id per interface inWLC 5500

DHCP discover andrequest packets arepadded with theoption 82 withsuboption 151 and152 when VPNselect is configuredwith the VPN id perinterface in WLC5500

WLJ80S_DHCP_08

PassedTo check if DHCP discoverand request packets are paddedwith the option 82 withsuboption 151 and 152 whenVRF select is configured withthe VRF name per interface inWLC 5500

DHCP discover andrequest packets arepadded with theoption 82 withsuboption 151 and152 when VRFselect is configuredwith the VRF perinterface in WLC5500

WLJ80S_DHCP_09


16

New Features - Test SummaryDHCP Relay Options


PassedTo check if DHCP relay optionwith HA. Ensure that the relayoptions configurations aresynced to the standby WLC inWLC 5500

DHCP relay optionwith HA in WLC5500

WLJ80S_DHCP_10

PassedTo check if config upload anddownload is successfullymaintaining the DHCP relayoptions config in WLC 5500

DHCP relay optionsconfigurationupload anddownload in WLC5500

WLJ80S_DHCP_11

PassedTo check if the DHCP relayoption 82 with both link andVPN select suboption workswith AAA override enabled inWLC 5500

AAA override withrelay options inWLC 5500

WLJ80S_DHCP_12

PassedTo check if there are adequatedebug messages for the DHCPrelay options in WLC 5500

Debug messages inWLC 5500

WLJ80S_DHCP_13

PassedTo check if DHCP relayoptions for both link and VPNselect works fine with Flexcentral switching inWLC5500

Flex centralswitching in WLC5500

WLJ80S_DHCP_14

PassedTo check if the L2 intracontroller works with DHCPrelay option 82 enabled inWLC 5500

L2/L3 Roamingwith DHCP relayoptions in WLC5500

WLJ80S_DHCP_15

PassedTo check if the DHCP OFFERand ACK packets have theoption 82 unpadded in WLC5500

DHCP OFFER andACK packets areunpadded withoption 82 in WLC5500

WLJ80S_DHCP_16

PassedTo check if the DHCP OFFERand ACK packets are checkedby WLC for option 82 withsuboption 152 in WLC 5500and if present the Critical errorhas to be logged in syslogserver and SNMP trap has tobe sent to NCS. Client shouldnot be denied IP address at anypoint

DHCP OFFER andACK packets arechecked by WLCfor option 82 withsuboption 152 andif present theCritical error has tobe logged in WLC5500

WLJ80S_DHCP_17


17



PassedTo Check the behavior whenthe DHCP relay option 82 withlink select or VPN / VRF selectis configured along withinvalid or non reachableDHCPserver in WLC 5500Ensurethat all the DHCP discover/Req packets that are retriedfrom the client and relayed byWLC carries the option 82with either suboption 5 /151and152

DHCP relay option82 with link selector VPN / VRFselect is configuredalong with invalidor non reachableDHCP server inWLC 5500

WLJ80S_DHCP_18

PassedTo Check the behavior whenthe DHCP relay option 82 withlink select and VPN / VRFselect is configured along withinvalid or non reachableprimary DHCP server and itfalls back to reachablesecondary DHCP server inWLC 5500Ensure that all theDHCP discover/req packetsthat are retried from the clientand relayed by WLC to theprimary and secondary DHCPserver carries the option 82with either suboption 5 /151and152

DHCP relay option82 with link selector VPN / VRFselect is configuredalong with invalidor non reachableprimary DHCPserver and it fallsback to reachablesecondary DHCPserver inWLC5500

WLJ80S_DHCP_19



WLJ80S_DHCP_20



WLJ80S_DHCP_21


DHCP relay options(link/VPN select )isenabled only whenthe DHCP proxyenabled in WLC7500

WLJ80S_DHCP_22


18





WLJ80S_DHCP_23



WLJ80S_DHCP_24



WLJ80S_DHCP_25



WLJ80S_DHCP_26



WLJ80S_DHCP_27



WLJ80S_DHCP_28


19





WLJ80S_DHCP_29



WLJ80S_DHCP_30



WLJ80S_DHCP_31



WLJ80S_DHCP_32



WLJ80S_DHCP_33



WLJ80S_DHCP_34



WLJ80S_DHCP_35



WLJ80S_DHCP_36


20





WLJ80S_DHCP_37



WLJ80S_DHCP_38



WLJ80S_DHCP_39



WLJ80S_DHCP_40


DHCP relay options(link/VPN select )isenabled only whenthe DHCP proxyenabled in WLC8500

WLJ80S_DHCP_41


21





WLJ80S_DHCP_42



WLJ80S_DHCP_43



WLJ80S_DHCP_44



WLJ80S_DHCP_45



WLJ80S_DHCP_46



WLJ80S_DHCP_47


22





WLJ80S_DHCP_48



WLJ80S_DHCP_49



WLJ80S_DHCP_50



WLJ80S_DHCP_51



WLJ80S_DHCP_52



WLJ80S_DHCP_53



WLJ80S_DHCP_54



WLJ80S_DHCP_55


23





WLJ80S_DHCP_56



WLJ80S_DHCP_57

Show Running ConfigDefectsStatusDescriptionTitleLogical ID

PassedTo check the format of showrun-config commands forWLC 2500

Show run-config_commands for WLC2500

WLJ80S_RC_01

PassedTo check that the commandis working without errorfrom WLC 2500

Show run-config_startup-commands forWLC 2500

WLJ80S_RC_02



WLJ80S_RC_03


24

New Features - Test SummaryShow Running Config




WLJ80S_RC_04



WLJ80S_RC_05



WLJ80S_RC_06



WLJ80S_RC_07



WLJ80S_RC_08

Flexconnect video streamingDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether VideoStream functionality isenabled/disabled forflexconnect local-switchingWLAN

Enabling/disablingVideo Stream forFLS WLAN

WLJ80S_FLSV_01

PassedTo verify the debug andshow commands supportedfor flexconnectlocal-switching VideoStream

Debug and showcommands for FLSVideo Streaming

WLJ80S_FLSV_02

PassedTo verify that thelocal-switching clientsubscribed to VideoStreaming receivesMC2UC traffic

MC2UC traffic tolocal-switchingclient

WLJ80S_FLSV_03

PassedTo verify the localswitching client receivingMC traffic when MC2UCis disabled at the WLAN

MC2UC traffic tolocal-switchingclient whenMC2UC is disabled

WLJ80S_FLSV_04


25

New Features - Test SummaryFlexconnect video streaming


PassedTo verify the localswitching client receivingMC traffic when MediaStream is disabled at AP

MC2UC traffic tolocal-switchingclient when Mediastream is removedat AP

WLJ80S_FLSV_05

PassedTo verify whether themultiple local-switchingclients receives MC2UCtraffic when subscribed toVideo Stream

Multiple LS clientsin same vlan, samewlan, receivingMC2UC traffic

WLJ80S_FLSV_06

PassedTo verify whether AP stopssending traffic when clientdisassociates

Client disassociateswhen receivingMC2UC traffic

WLJ80S_FLSV_07

PassedTo verify thelocal-switching clientreceiving MC2UC trafficroaming between radios ofthe AP

LS client receivingMC2UC trafficroam betweenradios at the AP

WLJ80S_FLSV_08

PassedTo verify thelocal-switching clientreceiving MC2UC trafficroaming between APs inthe flexconnect group

LS client receivingMC2UC trafficroam between APsin the flexconnectgroup

WLJ80S_FLSV_09

PassedTo verify whether AP hasno entry for the centralswitching client withMC2UC enabled

Central Switchingand Local switchingclient with MC2UCenabled

WLJ80S_FLSV_10

PassedTo verify whether the localswitching clients withMC2UC enabled receivesMC2UC traffic and LSclient with Media streamdisabled receives normalmulticast

Local switchingclients withMC2UC enabledand disabled

WLJ80S_FLSV_11

PassedTo verify whetherFlexconnect AP instandalone retains its VideoStream config

Flex AP instandalone moderetains the VideoStream config

WLJ80S_FLSV_12

PassedTo verify whetherFlexconnect AP instandalone retains its VideoStream config after reboot

Flex AP instandalone moderetains the VideoStream config afterreboot

WLJ80S_FLSV_13


26



PassedTo verify whether theflexconnect AP can loadthe updated config whenswitch from standalone toconnected mode

Flex AP fromstandalone toconnectedmode canload the updatedconfig

WLJ80S_FLSV_14

PassedTo verify whether the LSclient receives continuousMC2UC traffic when APmoves from connected >SA > connected with sameconfig

Flex LS clientreceiving MC2UCtraffic when APmove fromconnected > SA >connected withsame config

WLJ80S_FLSV_15

PassedTo verify whether the LSclient receives continuousMC2UC traffic when APmoves from connected >SA > connected withdifferent config

Flex LS clientreceiving MC2UCtraffic when APmove fromconnected > SA >connected withdifferent config

WLJ80S_FLSV_16

PassedTo verify whether clientre-associates and receivesMC2UC traffic when flexAP is rebooted inconnected mode.

Flex AP reboot inconnected modewhen Flex LS clientreceiving MC2UCtraffic

WLJ80S_FLSV_17

PassedTo verify whether clientre-associates and receivesMC2UC traffic when flexAP is rebooted instandalone mode

Flex AP reboot inSAmodewhen FlexLS client receivingMC2UC traffic

WLJ80S_FLSV_18

PassedTo verify whether the cliententries are removed whenAP adminmode is disabled

AP admin modedisabled when LSclient receivingMC2UC traffic

WLJ80S_FLSV_19

PassedTo verify whether the cliententries are removed whenAP radios are shut

AP radios shutdisabled when LSclient receivingMC2UC traffic

WLJ80S_FLSV_20

PassedTo verify whetherupgrading the WLC withlatest supported imageretains the Video Streamconfiguration forlocal-switching WLAN

Software Upgradeto the latest imagewith video streamconfig at AP

WLJ80S_FLSV_21


27



PassedTo verify whetherupgrading the WLC withunsupported image clearsthe Video Streamconfiguration forlocal-switching WLAN

Softwaredowngrade to theunsupported imagewith video streamconfig at AP

WLJ80S_FLSV_22

PassedTo verify whether theVideo Streaming config forLSWLANhas been syncedbetween the Active andStandby in HA setup

Video stream configsync for LS WLANin HA setup

WLJ80S_FLSV_23

PassedTo verify whether flex APretains the Video Streamingconfig post switchover

AP SSO withMC2UCenabled forLS WLAN

WLJ80S_FLSV_24

PassedTo verify whether LS clientwith MC2UC enabledreceives unicast traffic afterswitchover

LS client withMC2UC enabledreceiving trafficafter switchover inHA pair

WLJ80S_FLSV_25

Flexconnect Upgrade Time ReductionDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether changingthe AP mode from local toflexconnect usingWLCCLIis successful withoutrebooting the AP

AP mode changefrom local toflexconnect usingWLC CLI

WLJ80S_FC_01

PassedTo verify whether changingthe AP mode from local toflexconnect usingWLCGUIis successful withoutrebooting the AP

AP mode changefrom local toflexconnect usingWLC GUI

WLJ80S_FC_02

PassedTo verify whether basic flexconfigurations have beenapplied to AP after modechange

Basic flexconfiguration afterAP mode change

WLJ80S_FC_03


28

New Features - Test SummaryFlexconnect Upgrade Time Reduction


PassedTo verify whether client hasbeen successfullyauthenticated after APmodehas been changed toflexconnect with centralswitching WLAN

Clientauthentication withAP after modechange toflexconnect_CentralSwitching

WLJ80S_FC_04

PassedTo verify whether client hasbeen successfullyauthenticated after APmodehas been changed toflexconnect with localswitching, central authWLAN

Clientauthentication withAP after modechange toflexconnect_LocalSwitching ,Centralauth

WLJ80S_FC_05

PassedTo verify whether client hasbeen associated successfullyto AP in standalone modeand fault tolerance

Client associationwith AP instandalone modeand FT

WLJ80S_FC_06

PassedTo verify whether convertedflex AP retains all configwhen AP is rebooted inconnected/standalone mode

AP reboot inconnected/standalonemode, for convertedflex AP

WLJ80S_FC_07

PassedTo verify the clientassociation with AP rebootin connected/standalonemode, for AP converted toflex

Client associationwith AP reboot inconnected/standalonemode

WLJ80S_FC_08

PassedTo verify whether the APretains its flex configurationafter softwareupgrade/downgrade

Softwareupgrade/downgrade

WLJ80S_FC_09

PassedTo verify the AP modechange inHA setup, whetherAP mode is synched tostandby

HA support formode change

WLJ80S_FC_10

PassedTo verify the AP mode withauto conversion on WLC

AP mode changewith autoconversion onWLC

WLJ80S_FC_11

PassedTo verify the roamingwithinthe controller is successful

Intra-Controllerroam, localswitching WLAN

WLJ80S_FC_12

PassedTo verify the inter-controllerroaming is successful

Inter-Controllerroam, centralswitching WLAN

WLJ80S_FC_13


29

New Features - Test SummaryFlexconnect Upgrade Time Reduction


PassedTo verify whether change ofAP mode for few Aps aresuccessful

APmode change forfew Aps

WLJ80S_FC_14

PassedTo verify whether changingthe mode from local > flex> local for few times areworking properly

Mode change fromlocal > flex > local

WLJ80S_FC_15

PassedTo verify the mode changeto flexconnect and then toWIPS

Mode change toflexconnect then tosubmode wIPS

WLJ80S_FC_16

8500 As Mobility ControllerDefectsStatusDescriptionTitleLogical ID

PassedTo check if "New Mobility"could be successfully enabledfrom the CLI and GUI

Enabling NewMobility from CLI& GUI of 8500

WLJ80S_MC_01

PassedTo check if the mobilitygroup members aresuccessfully added fromGUIand CLI

ConfiguringMobility groupmembers from GUIand CLI of 8500

WLJ80S_MC_02

PassedTo check if the multicastmode can be enabled/disabledfrom CLI and GUI and checkfor the changes to have takeneffect

Enable/DisableMobility Multicastmode from CLI &GUI of 8500

WLJ80S_MC_03

PassedTo create / delete a Switchpeer group from the CLI andGUI and check the changesto have taken effect.

Create and deleteSwitch Peer groupfrom GUI & CLI in8500

WLJ80S_MC_04

PassedTo add a switch peer groupmember to a created switchpeer group fromCLI andGUIand check if theconfigurations are successful.

Add switch peergroupmember fromthe GUI & CLI in8500

WLJ80S_MC_05

PassedTo verify if intra Switch /MA roaming occurs smoothlywhen 8500 is acting as MChaving a WLAN with openauthentication

Client Intra MAroaming when 8500is the MC(open L2security on theWLAN)

WLJ80S_MC_06


30

New Features - Test Summary8500 As Mobility Controller


PassedTo verify if intra Switch /MA roaming occurs smoothlywhen 8500 is acting as MCwith aWLAN having 802.1xsecurity type.

Client Intra MAroaming when 8500is the MC (802.1xon the WLAN)

WLJ80S_MC_07

PassedTo verify if intra Switch /MA roaming occurs smoothlywhen 8500 is acting as MCwith a WLAN having WEPor WPA2 security type.

Client Intra MAroaming when 8500is the MC(WEP/WPA2 on theWLAN)

WLJ80S_MC_08

PassedTo verify if intra switch peergroup roaming occurssmoothly when 8500 is actingas MC with a WLAN havingopen security type.

Intra switch Peergroup roamingwhen 8500 is actingas the MC for theparticular peergroup (WLANhaving 'none' as L2security)

WLJ80S_MC_09

PassedTo verify if intra switch peergroup roaming occurssmoothly when 8500 is actingas MC with a WLAN having"WEP" security type.

Intra switch Peergroup roamingwhen 8500 is actingas the MC for theparticular peergroup (WLANhaving 'WEP' as L2security)

WLJ80S_MC_10

PassedTo verify if intra switch peergroup roaming occurssmoothly when 8500 is actingas MC with a WLAN having"802.1x" security type.

Intra switch Peergroup roamingwhen 8500 is actingas the MC for theparticular peergroup (WLANhaving '802.1x' asL2 security)

WLJ80S_MC_11

PassedTo verify if intra switch peergroup roaming occurssmoothly when 8500 is actingas MC with a WLAN having"WPA-2-PSK" security type.

Intra switch Peergroup roamingwhen 8500 is actingas the MC for theparticular peergroup (WLANhaving 'WPA2-PSK'as L2 security)

WLJ80S_MC_12


31



PassedTo verify if intra switch peergroup dual roaming occurssmoothly when 8500 is actingas MC with a WLAN having"WPA-2-PSK" security type.

Intra switch Peergroup dual roamingroaming when 8500is acting as the MCfor the particularpeer group (WLANhaving 'WPA2-PSK'as L2 security)

WLJ80S_MC_13

PassedTo verify if intra switch peergroup dual roaming occurssmoothly when 8500 is actingas MC with a WLAN having"none" as the security type.

Intra switch Peergroup dual roamingroaming when 8500is acting as the MCfor the particularpeer group (WLANhaving 'none' as L2security)

WLJ80S_MC_14

PassedTo verify if intra switch peergroup dual roaming occurssmoothly when 8500 is actingas MC with a WLAN having"WEP" as the security type.

Intra switch Peergroup dual roamingroaming when 8500is acting as the MCfor the particularpeer group (WLANhaving 'WEP' as L2security)

WLJ80S_MC_15

PassedTo verify if intra switch peergroup dual roaming occurssmoothly when 8500 is actingas MC with a WLAN having"802.1x" as the security type.

Intra switch Peergroup dual roamingroaming when 8500is acting as the MCfor the particularpeer group (WLANhaving '802.1x' asL2 security)

WLJ80S_MC_16

PassedTo verify if the PoP stays thesame and PoA moves to newMA after roamingwith stickyanchor (default behavior) ona WLAN with 'none' as L2security

Intra SPG roamingwith sticky anchorwhen 8500controller is actingas MC on a WLANwith openauthentication

WLJ80S_MC_17

PassedTo verify if the PoP stays thesame and PoA moves to newMA after roamingwith stickyanchor (default behavior) ona WLAN with 'WEP' as L2security

Intra SPG roamingwith sticky anchorwhen 8500controller is actingas MC on a WLANwith 'WEP' as L2security type.

WLJ80S_MC_18


32



PassedTo verify if the PoP stays thesame and PoA moves to newMA after roamingwith stickyanchor (default behavior) ona WLAN with '802.1x' as L2security

Intra SPG roamingwith sticky anchorwhen 8500controller is actingas MC on a WLANwith '802.1x' as L2security type.

WLJ80S_MC_19

PassedTo verify if the PoP stays thesame and PoA moves to newMA after roamingwith stickyanchor (default behavior) onaWLANwith 'WPA-PSK' asL2 security

Intra SPG roamingwith sticky anchorwhen 8500controller is actingas MC on a WLANwith 'WPA2-PSK'as L2 security type.

WLJ80S_MC_20

PassedTo verify if the PoP and PoAmoves to new MA afterroaming without stickyanchor on a WLAN with'none' as L2 security

Intra SPG roamingwithout stickyanchor when 8500controller is actingas MC on a WLANwith openauthentication

WLJ80S_MC_21

PassedTo verify if the PoP and PoAmoves to new MA afterroaming without stickyanchor on a WLAN with'Static WEP' as L2 security

Intra SPG roamingwithout stickyanchor when 8500controller is actingas MC on a WLANwith WEP security

WLJ80S_MC_22

PassedTo verify if the PoP and PoAmoves to new MA afterroaming without stickyanchor on a WLAN with'802.1x' as L2 security

Intra SPG roamingwithout stickyanchor when 8500controller is actingas MC on a WLANwith 802.1x security

WLJ80S_MC_23

PassedTo verify if the PoP and PoAmoves to new MA afterroaming without stickyanchor on a WLAN with'WPA2-PSK' as L2 security

Intra SPG roamingwithout stickyanchor when 8500controller is actingas MC on a WLANwith WPA2-PSKsecurity

WLJ80S_MC_24


33



PassedTo verify if roaming betweenAPs belonging to MA's indifferent SPGs works finewhen 8500 is acting as MCwith aWLAN having "open"l2 security.

Inter SPG L2roaming when 8500is the MC with aWLANhaving openauthentication

WLJ80S_MC_25

PassedTo verify if roaming betweenAPs belonging to MA's indifferent SPGs works finewhen 8500 is acting as MCwith aWLANhaving "WEP"l2 security.

Inter SPG L2roaming when 8500is the MC with aWLAN havingWEP

WLJ80S_MC_26

PassedTo verify if roaming betweenAPs belonging to MA's indifferent SPGs works finewhen 8500 is acting as MCwith a WLAN having"802.1x" l2 security.

Inter SPG L2roaming when 8500is the MC with aWLAN having"802.1x" at L2security

WLJ80S_MC_27

PassedTo verify if roaming betweenAPs belonging to MA's indifferent SPGs works finewhen 8500 is acting as MCwith a WLAN having"WPA2-PSK" l2 security.

Inter SPG L2roaming when 8500is the MC with aWLAN having"WPA2-PSK" at L2security

WLJ80S_MC_28

PassedTo verify if the PoP stays thesame in inter-SPG roamingwith sticky roaming, PoAchanges and traffic flow takesthe path NewMA->MC->oldMA on other SPG

PoP, PoA and trafficflow in inter SPGroaming with stickyroaming when 8500is acting asMCwitha WLAN having"none" as L2security

WLJ80S_MC_29


PoP, PoA and trafficflow in inter SPGroaming with stickyroaming when 8500is acting asMCwitha WLAN having"WEP" as L2security

WLJ80S_MC_30


34





WLJ80S_MC_31



WLJ80S_MC_32

PassedTo verify if the PoP and PoAmoves to the new MA ininter-SPG roaming withoutsticky roaming and trafficflow takes the path NewMA-> datacenter

PoP, PoA and trafficflow in inter SPGroaming withoutsticky roamingwhen 8500 is actingas MC with aWLAN having"none" as L2security

WLJ80S_MC_33


PoP, PoA and trafficflow in inter SPGroaming withoutsticky roamingwhen 8500 is actingas MC with aWLAN having"WEP" as L2security

WLJ80S_MC_34


PoP, PoA and trafficflow in inter SPGroaming withoutsticky roamingwhen 8500 is actingas MC with aWLAN having"WPA2-PSK" as L2security

WLJ80S_MC_35


35




PoP, PoA and trafficflow in inter SPGroaming withoutsticky roamingwhen 8500 is actingas MC with aWLAN having"802.1X" as L2security

WLJ80S_MC_36

PassedTo verify if the roaming ofclient from an AP associatedto MA of a SPG->SPG1->SPG2 works finewhen 8500 is acting as MCwith aWLAN having "none"as L2 security type.

Inter SPG roamingwithin 3 separateSPGs with 8500 acMC having aWLAN with 'open'authentication

WLJ80S_MC_37

PassedTo verify if the roaming ofclient from an AP associatedto MA of a SPG->SPG1->SPG2 works finewhen 8500 is acting as MCwith aWLANhaving "WEP"as L2 security type.

Inter SPG roamingwithin 3 separateSPGs with 8500 acMC having aWLAN with 'WEP'as L2 securitymethod.

WLJ80S_MC_38

PassedTo verify if the roaming ofclient from an AP associatedto MA of a SPG->SPG1->SPG2 works finewhen 8500 is acting as MCwith a WLAN having"802.1x" as L2 security type.

Inter SPG roamingwithin 3 separateSPGs with 8500 acMC having aWLAN with'802.1x'authentication

WLJ80S_MC_39

PassedTo verify if the roaming ofclient from an AP associatedto MA of a SPG->SPG1->SPG2 works finewhen 8500 is acting as MCwith a WLAN having"WPA2-PASK" as L2security type.

Inter SPG roamingwithin 3 separateSPGs with 8500 acMC having aWLAN with'WPA2-PSK'authentication

WLJ80S_MC_40

PassedTo verify if roaming betweenAPs belonging to MA's indifferent SPGs on differentsubnet works fine when 8500is acting as MC with aWLAN having "open" l2security.

Inter SPG L3roaming when 8500is the MC with aWLANhaving openauthentication

WLJ80S_MC_41


36



PassedTo verify if roaming betweenAPs belonging to MA's indifferent SPGs on differentsubnet works fine when 8500is acting as MC with aWLAN having "WEP" l2security.

Inter SPG L3roaming when 8500is the MC with aWLAN having'WEP' as L2security

WLJ80S_MC_42

PassedTo verify if roaming betweenAPs belonging to MA's indifferent SPGs on differentsubnet works fine when 8500is acting as MC with aWLAN having "802.1x" l2security.

Inter SPG L3roaming when 8500is the MC with aWLAN having'802.1x' as L2security

WLJ80S_MC_43

PassedTo verify if roaming betweenAPs belonging to MA's indifferent SPGs on differentsubnet works fine when 8500is acting as MC with aWLANhaving "WPA2-PSK"l2 security.

Inter SPG L3roaming when 8500is the MC with aWLAN having'WPA2-PSK' as L2security

WLJ80S_MC_44

PassedTo verify if the L2 roambetween twoMC's works finewhen the WLAN has 'none'as L2 security.

Roaming betweentwo 8500 MobilityControllers in thesame subnet whenthe WLAN has'none' as L2 security

WLJ80S_MC_45

PassedTo verify if the L2 roambetween twoMC's works finewhen theWLAN has '802.1x'as L2 security.

Roaming betweentwo 8500 MobilityControllers in thesame subnet whenthe WLAN has'802.1x' as L2security

WLJ80S_MC_46

PassedTo verify if the L2 roambetween twoMC's works finewhen the WLAN has 'WEP'as L2 security.

Roaming betweentwo 8500 MobilityControllers in thesame subnet whenthe WLAN has'WEP' as L2security

WLJ80S_MC_47


37



PassedTo verify if the L2 roambetween twoMC's works finewhen the WLAN has'WPA2-PSK' as L2 security.

Roaming betweentwo 8500 MobilityControllers in thesame subnet whenthe WLAN has'WPA2-PSK' as L2security

WLJ80S_MC_48

PassedTo verify if the L2 roambetween two MC's indifferent subnet works finewhen the WLAN has 'none'as L2 security.

Roaming betweentwo 8500 MobilityControllers indifferent subnetwhen the WLANhas 'none' as L2security

WLJ80S_MC_49

PassedTo verify if the L2 roambetween two MC's indifferent subnet works finewhen the WLAN has 'WEP'as L2 security.

Roaming betweentwo 8500 MobilityControllers indifferent subnetwhen the WLANhas 'WEP' as L2security

WLJ80S_MC_50

PassedTo verify if the L2 roambetween two MC's indifferent subnet works finewhen theWLAN has '802.1x'as L2 security.

Roaming betweentwo 8500 MobilityControllers indifferent subnetwhen the WLANhas '802.1x' as L2security

WLJ80S_MC_51

PassedTo verify if the L2 roambetween two MC's indifferent subnet works finewhen the WLAN has'WPA2-PSK' as L2 security.

Roaming betweentwo 8500 MobilityControllers indifferent subnetwhen the WLANhas 'WPA2-PSK' asL2 security

WLJ80S_MC_52

PassedTo verify if the mobilitytunnel gets establishedbetween two 8500MCswhenone of the Controllers PrivateIP address is NAT'ed

Addition of NATfunctionalitybetween two 8500MCs

WLJ80S_MC_53


38



PassedTo verify if the L2 roamingof Static IP 5300 agn wirelessclient within the subdomainworks fine .

L2 roaming ofStatic ip 5300 agnWireless clientswithin thesubdomain of the8500 MC

WLJ80S_MC_54

PassedTo verify if the L2 roamingof Static IP MAC wirelessclient within the subdomainworks fine .

L2 roaming ofStatic IP MACWireless clientswithin thesubdomain of the8500 MC

WLJ80S_MC_55

PassedTo verify if the L3 roamingof Static IP 5300 agn wirelessclient within the Subdomainworks fine .

L3 roaming ofStatic IP 5300 agnWireless clientswithin thesubdomain of the8500 MC

WLJ80S_MC_56

PassedTo verify if the L3 roamingof Static IP MAC wirelessclient within the Subdomainworks fine .

L3 roaming ofStatic IP MACWireless clientswithin thesubdomain of the8500 MC

WLJ80S_MC_57

PassedTo verify if the client getsanchored to thecorresponding MC-anchorwhen connected in Wirelessto the MA where theassociated MC-is actingforeign controller.

Initial association ofWired Guest clientto the MA when8500 is acting asMC.

WLJ80S_MC_58

PassedTo verify if the client getsanchored to thecorresponding MC-anchorwhen wired to the MAwherethe associated MC-is actinga foreign controller.

Initial association ofWireless Guestclient to the MAwhen 8500 is actingas MC.

WLJ80S_MC_59

PassedTo verify if the L2 and L3roaming of Guest clientshappens successfully betweentwo MC's.

Roaming of guestclients within the8500 MCs

WLJ80S_MC_60


39


HA Enhancements

HA Pair up by connecting RP back-to-back

Internal DHCP support


PassedTo verify whether InternalDHCP has been configuredwhen HA is enabled throughCLI

Internal DHCPconfig in HA pairthrough CLI

WLJ80S_HA_Enh_01

PassedTo verify whether InternalDHCP has been configuredwhen HA is enabled throughGUI

Internal DHCPconfig in HA pairthrough GUI

WLJ80S_HA_Enh_02

PassedTo verify whether the InternalDHCP config through ActiveCLI/GUI is synced to theStandby-Hot WLC in a HA pair

Internal DHCPconfig sync inStandby-Hot

WLJ80S_HA_Enh_03

PassedTo verify the Internal DHCPconfig during Incremental sync

Internal DHCPconfig duringIncremental sync

WLJ80S_HA_Enh_04

PassedTo verify the Internal DHCPconfig during Bulk sync

Internal DHCPconfig during Bulksync

WLJ80S_HA_Enh_05

PassedTo verify the Internal DHCPconfig in new Active WLC.

Internal DHCPconfig in newActive

WLJ80S_HA_Enh_06

PassedTo verify whether the clientobtaining IP address from theInternal DHCP config

Client obtaining IPthrough InternalDHCP config

WLJ80S_HA_Enh_07

PassedTo verify whether the clientobtaining IP address from theInternal DHCP after aswitchover

Client IP addressafter a switchover

WLJ80S_HA_Enh_08

PassedTo verify the Internal DHCPconfig upload/download fromActive and peer

Upload/download ofInternal DHCPconfig

WLJ80S_HA_Enh_09

PassedTo verify the Internal DHCPconfig is persistent acrossupgrade/downgrade of HA pair

Upgrade/downgradeof HA pair withInternal DHCPconfig with 8.0image

WLJ80S_HA_Enh_10


40

New Features - Test SummaryHA Enhancements


PassedTo verify Internal DHCP configis not allowedwhen downgradedto 7.6/7.5

Downgrade WLCpair to 7.6/7.5 withInternal DHCPconfig

WLJ80S_HA_Enh_11

Sleeping Client Sync


PassedTo verify the sleeping cliententry sync to the standbyWLC-Internal web authentication

SleepingClient syncin Standby- Internalweb auth

WLJ80S_HA_Enh_12

PassedTo verify the sleeping cliententry sync to the standbyWLC-Customized web authentication

SleepingClient syncin Standby-customized webauth

WLJ80S_HA_Enh_13

PassedTo verify the sleeping cliententry sync to the standbyWLC-External web authentication

SleepingClient syncin Standby- externalweb auth

WLJ80S_HA_Enh_14

PassedTo verify the sleeping cliententry sync to the standbyWLC-Dot1x + web auth

SleepingClient syncin Standby- Dot1x+ web auth

WLJ80S_HA_Enh_15

PassedTo verify the sleeping cliententry in bulk sync to thestandby- internal andcustomized web authentication

Sleeping Cliententry bulk sync-internal andcustomized webauthentication

WLJ80S_HA_Enh_16

PassedTo verify the sleeping cliententry in bulk sync to thestandby- external and dot1x +web-auth

Sleeping Cliententry bulk sync-external anddot1x+web auth.

WLJ80S_HA_Enh_17

PassedTo verify the sleeping cliententry sync in standby enablingFlexconnect local switching

Sleeping client entrysync in Flexconnectlocal switching

WLJ80S_HA_Enh_18

PassedTo verify the sleeping clientstatus after switchover withInternal/customized web auth

Sleeping clientstatus afterswitchover- internalweb auth

WLJ80S_HA_Enh_19

PassedTo verify the sleeping clientstatus after switchover withexternal/dot1x+ web auth

Sleeping clientstatus afterswitchover- externalweb auth

WLJ80S_HA_Enh_20


41



PassedTo verify the sleeping cliententry deletion sync betweenActive and Standby

Sleeping client entrydeletion sync

WLJ80S_HA_Enh_21

PassedTo verify the Sleeping clientstatus after sleep timer expiresin new Active after switchover

Sleeping Client innew Active aftersleep timer expires

WLJ80S_HA_Enh_22

SSO support for OEAP


PassedTo verify whether OEAP issynced between Active andStandby WLC

OEAP syncbetween Active andStandbyWLC uponjoining

WLJ80S_HA_Enh_23

PassedTo verify whether the OEAPis removed from Active andStandby WLC when powereddown the AP

OEAP syncbetween Active andStandbyWLCwhenremoved

WLJ80S_HA_Enh_24

PassedTo verify whether OEAPswitchovers in a seamlessmanner to the new Activeupon switchover

OEAP afterswitchover

WLJ80S_HA_Enh_25

PassedTo verify whether the clientsconnected through corporateSSID are synced to Standby

Sync of Clientconnected tocorporate SSID

WLJ80S_HA_Enh_26

PassedTo verify whether the clientsconnected through personalSSID are synced to Standby

Sync of Clientconnected topersonal SSID

WLJ80S_HA_Enh_27

PassedTo verify the client connectedto Corporate SSID afterswitchover

Client connected tocorporate SSIDafter switchover

WLJ80S_HA_Enh_28

PassedTo verify the client connectedto Personal SSID afterswitchover

Client connected topersonal SSID afterswitchover

WLJ80S_HA_Enh_29

PassedTo verify the Join statisticsand counters sync of OEAP

OEAP join statisticsand Counters sync

WLJ80S_HA_Enh_30

PassedTo verify the client SSO withOEAP

Client SSO withOEAP

WLJ80S_HA_Enh_31

PassedTo verify the voice clientstatus connected to OEAPafter switchover

Voice clientconnected to OEAPafter switchover

WLJ80S_HA_Enh_32


42


CAC statistics sync


PassedTo verify the voice CACsummary in new ActiveWLC after switchover

Voice CACsummary in newActive WLC

WLJ80S_HA_Enh_33

PassedTo verify the voice CACstats in new Active WLCafter switchover

Voice CAC stats innew Active WLC

WLJ80S_HA_Enh_34

PassedTo verify the voice stats inAP stats after switchover

Voice stats in APstats afterswitchover

WLJ80S_HA_Enh_35

HA Pair up by connecting RP via a L2 switch

Internal DHCP support


PassedTo verify whether InternalDHCP has been configuredwhen HA is enabled throughCLI

Internal DHCPconfig in HA pairthrough CLI

WLJ80S_HA_Enh_36

PassedTo verify whether InternalDHCP has been configuredwhen HA is enabled throughGUI

Internal DHCPconfig in HA pairthrough GUI

WLJ80S_HA_Enh_37

PassedTo verify whether the InternalDHCP config through ActiveCLI/GUI is synced to theStandby-Hot WLC in a HApair

Internal DHCPconfig sync inStandby-Hot

WLJ80S_HA_Enh_38

PassedTo verify the Internal DHCPconfig during Incrementalsync

Internal DHCPconfig duringIncremental sync

WLJ80S_HA_Enh_39

PassedTo verify the Internal DHCPconfig during Bulk sync

Internal DHCPconfig during Bulksync

WLJ80S_HA_Enh_40

PassedTo verify the Internal DHCPconfig in new Active WLC.

Internal DHCPconfig in newActive

WLJ80S_HA_Enh_41

PassedTo verify whether the clientobtaining IP address from theInternal DHCP config

Client obtaining IPthrough InternalDHCP config

WLJ80S_HA_Enh_42


43



PassedTo verify whether the clientobtaining IP address from theInternal DHCP after aswitchover

Client IP addressafter a switchover

WLJ80S_HA_Enh_43

PassedTo verify the Internal DHCPconfig upload/download fromActive and peer

Upload/download ofInternal DHCPconfig

WLJ80S_HA_Enh_44

PassedTo verify the Internal DHCPconfig is persistent acrossupgrade/downgrade of HApair

Upgrade/downgradeof HA pair withInternal DHCPconfig with 8.0image

WLJ80S_HA_Enh_45

PassedTo verify Internal DHCPconfig is removed whendowngraded to 7.6/7.5

Downgrade WLCpair to 7.6/7.5 withInternal DHCPconfig

WLJ80S_HA_Enh_46

Sleeping Client Sync


PassedTo verify thesleeping client entrysync to the standbyWLC- Internal webauthentication

SleepingClient syncin Standby- Internalweb auth

WLJ80S_HA_Enh_47

PassedTo verify thesleeping client entrysync to the standbyWLC- Customizedweb authentication

SleepingClient syncin Standby-customized webauth

WLJ80S_HA_Enh_48

PassedTo verify thesleeping client entrysync to the standbyWLC- External webauthentication

SleepingClient syncin Standby- externalweb auth

WLJ80S_HA_Enh_49

PassedTo verify thesleeping client entrysync to the standbyWLC- Dot1x + webauth

SleepingClient syncin Standby- Dot1x+ web auth

WLJ80S_HA_Enh_50


44



PassedTo verify thesleeping client entryin bulk sync to thestandby- internaland customizedwebauthentication

Sleeping Cliententry bulk sync-internal andcustomized webauthentication

WLJ80S_HA_Enh_51

PassedTo verify thesleeping client entryin bulk sync to thestandby- externaland dot1x +web-auth

Sleeping Cliententry bulk sync-external anddot1x+web auth.

WLJ80S_HA_Enh_52

PassedTo verify thesleeping client entrysync in standbyenablingFlexconnect localswitching

Sleeping client entrysync in Flexconnectlocal switching

WLJ80S_HA_Enh_53

PassedTo verify thesleeping clientstatus afterswitchover withInternal/customizedweb auth

Sleeping clientstatus afterswitchover- internalweb auth

WLJ80S_HA_Enh_54

PassedTo verify thesleeping clientstatus afterswitchover withexternal/dot1x+webauth

Sleeping clientstatus afterswitchover- externalweb auth

WLJ80S_HA_Enh_55

PassedTo verify thesleeping client entrydeletion syncbetween Active andStandby

Sleeping client entrydeletion sync

WLJ80S_HA_Enh_56

PassedTo verify theSleeping clientstatus after sleeptimer expires in newActive afterswitchover

Sleeping Client innew Active aftersleep timer expires

WLJ80S_HA_Enh_57

SSO support for OEAP


45



PassedTo verify whether OEAP issynced between Active andStandby WLC

OEAP syncbetween Active andStandbyWLCuponjoining

WLJ80S_HA_Enh_58

PassedTo verify whether the OEAPis removed from Active andStandby WLC when powereddown the AP

OEAP syncbetween Active andStandbyWLCwhenremoved

WLJ80S_HA_Enh_59

PassedTo verify whether OEAPswitchovers in a seamlessmanner to the new Activeupon switchover

OEAP afterswitchover

WLJ80S_HA_Enh_60

PassedTo verify whether the clientsconnected through corporateSSID are synced to Standby

Sync of Clientconnected tocorporate SSID

WLJ80S_HA_Enh_61

PassedTo verify whether the clientsconnected through personalSSID are synced to Standby

Sync of Clientconnected topersonal SSID

WLJ80S_HA_Enh_62

PassedTo verify the client connectedto Corporate SSID afterswitchover

Client connected tocorporate SSIDafter switchover

WLJ80S_HA_Enh_63

PassedTo verify the client connectedto Personal SSID afterswitchover

Client connected topersonal SSID afterswitchover

WLJ80S_HA_Enh_64

PassedTo verify the Join statistics andcounters sync of OEAP

OEAP join statisticsand Counters sync

WLJ80S_HA_Enh_65

PassedTo verify the client SSO withOEAP

Client SSO withOEAP

WLJ80S_HA_Enh_66

PassedTo verify the voice clientstatus connected to OEAPafter switchover

Voice clientconnected to OEAPafter switchover

WLJ80S_HA_Enh_67

CAC statistics sync


PassedTo verify the voice CACsummary in new ActiveWLC after switchover

Voice CACsummary in newActive WLC

WLJ80S_HA_Enh_68

PassedTo verify the voice CACstats in new Active WLCafter switchover

Voice CAC stats innew Active WLC

WLJ80S_HA_Enh_69


46



PassedTo verify the voice stats inAP stats after switchover

Voice stats in APstats afterswitchover

WLJ80S_HA_Enh_70

HTTPS Support

HTTPS Support for Web-Auth


PassedTo check whether HTTPSURL gets redirected or notto web-auth login page whenclient gets connected andbrowses the internet access.

Associating Win 7client to web-authsecurity andchecking theredirection ofHTTPS URL in7500 WLC.

WLJ80S_HTTPS_01

PassedTo check whether HTTPSURL gets redirected or notto web-auth login page whenclients gets connected andbrowses the internet and alsochecking the Ping functionworks or not between them.

Associating twoclients(Win 7 andMacbook) toweb-auth securityand checking theredirection ofHTTPSURL in bothclients in 7500WLC.

WLJ80S_HTTPS_02


Associating twoclients(Win 7 andWin 8) to web-authsecurity andchecking theredirection ofHTTPSURL in bothclients in 7500WLC.

WLJ80S_HTTPS_03


AssociatingSamsung S4 toweb-auth securityand checking theredirection ofHTTPS URL in itsbrowser in 7500WLC.

WLJ80S_HTTPS_04


47

New Features - Test SummaryHTTPS Support



Associating AppleIphone to web-authsecurity andchecking theredirection ofHTTPS URL in itsbrowser in 7500WLC.

WLJ80S_HTTPS_05



WLJ80S_HTTPS_06



WLJ80S_HTTPS_07



WLJ80S_HTTPS_08



WLJ80S_HTTPS_09


48





WLJ80S_HTTPS_10



WLJ80S_HTTPS_11



WLJ80S_HTTPS_12



WLJ80S_HTTPS_13



WLJ80S_HTTPS_14


49





WLJ80S_HTTPS_15


Associating Win 7client to web-authsecurity andchecking theredirection ofHTTPS URL inWiSM2.

WLJ80S_HTTPS_16


Associating twoclients(Win 7 andMacbook) toweb-auth securityand checking theredirection ofHTTPSURL in bothclients in WiSM2.

WLJ80S_HTTPS_17


Associating twoclients(Win 7 andWin 8) to web-authsecurity andchecking theredirection ofHTTPSURL in bothclients in WiSM2.

WLJ80S_HTTPS_18


AssociatingSamsung S4 toweb-auth securityand checking theredirection ofHTTPS URL in itsbrowser in WiSM2.

WLJ80S_HTTPS_19


Associating AppleIphone to web-authsecurity andchecking theredirection ofHTTPS URL in itsbrowser in WiSM2.

WLJ80S_HTTPS_20


50


NBAR Engine 3.10 - 8.0DefectsStatusDescriptionTitleLogical ID

PassedThis is to verify that afterupgrade from an older releasethat supports older AVCengine to 8.0 does not breakthe basic classificationfunctionality of AVC. Theolder release will be uploadedwith the latest protocol pack6.0 and then upgraded to 8.0

Check AVCvisibility onupgrade from olderrelease to 8.0 withchanging protocolpack in 2500

WLJ80S_AVC_01

PassedThis is to verify that afterdowngrade from 8.0 to anolder release AVCfunctionality should not breakand AVC config maintainedacross wlans. The 8.0 imageby default will have 4.1 AVCprotocol pack which will beupgraded to the latest 6.0protocol pack beforedowngrading

Check AVCvisibility ondowngrade from 8.0to an older releasewith the latestprotocol packuploaded in 8.0image in 2500

WLJ80S_AVC_02

PassedThis test case is to verifynetflow behavior with 8.0WLC image with 3.10 engineversion. The test will alsocheck if DSCPmarking is sentin the net flow records and 90sflow cache update happens

Check netflowflow-cache isupdated every 90sand traffic sent withdscp values in 2500

WLJ80S_AVC_03

PassedThis is to verify that afterupgrade to 8.0 multipleapplications for multipleclients are classified asexpected.

Verify AVCclassifies multipleapplications formultiple clientsassociated to asingle WLC 2500

WLJ80S_AVC_04



WLJ80S_AVC_05


51

New Features - Test SummaryNBAR Engine 3.10 - 8.0



Check netflowflow-cache isupdated every 90sand traffic sent withdscp values inWiSM2

WLJ80S_AVC_06



WLJ80S_AVC_07



WLJ80S_AVC_08


Check AVCvisibility onupgrade from olderrelease to 8.0 withchanging protocolpack in WiSM2

WLJ80S_AVC_09



WLJ80S_AVC_10


52





WLJ80S_AVC_11



WLJ80S_AVC_12


Check AVCvisibility ondowngrade from 8.0to an older releasewith the latestprotocol packuploaded in 8.0image in WiSM2

WLJ80S_AVC_13



WLJ80S_AVC_14



WLJ80S_AVC_15


53




Verify AVCclassifies multipleapplications formultiple clientsassociated to asingle WLCWiSM2

WLJ80S_AVC_16

PassedThis is to verify that CLIconfiguration for AVC profilewith Local policy engine isconfigurable as expected andalso check RADIUSwith ACS

Check AVC profileintegration withLocal policy CLIalongwithRADIUSusing SSH in 2500

WLJ80S_AVC_17


Check AVC profileintegration withLocal policy CLIalongwithRADIUSusing Telnet in2500

WLJ80S_AVC_18



WLJ80S_AVC_19



WLJ80S_AVC_20


Check AVC profileintegration withLocal policy CLIalongwithRADIUSusing SSH inWiSM2

WLJ80S_AVC_21



WLJ80S_AVC_22


54





WLJ80S_AVC_23


Check AVC profileintegration withLocal policy CLIalongwithRADIUSusing Telnet inWiSM2

WLJ80S_AVC_24

PassedThis is to verify that GUIconfiguration for AVC profilewith Local policy engine isconfigurable as expected andalso check RADIUSwith ACS

Check AVC profileintegration withLocal policy GUIalongwithRADIUSusing 2500

WLJ80S_AVC_25



WLJ80S_AVC_26



WLJ80S_AVC_27


Check AVC profileintegration withLocal policy GUIalongwithRADIUSusing WiSM2

WLJ80S_AVC_28

PassedThis is to verify that AVCLocal policy configurationfrom SNMP

To check AVCintegration withLocal policyconfiguration fromSNMP using 2500

WLJ80S_AVC_29



WLJ80S_AVC_30


55





WLJ80S_AVC_31


To check AVCintegration withLocal policyconfiguration fromSNMP usingWiSM2

WLJ80S_AVC_32

PassedThis is to verify AVC LocalPolicy config and AVCbehavior after config uploadand download

Config downloadcheck for AVClocal policy config

WLJ80S_AVC_33

PassedThis is to verify AVC Localpolicy intersection withupgrade and downgrade

Upgrade /Downgrade checkfor AVC Localpolicy config

WLJ80S_AVC_34

PassedThis is to verify that AVCprofile is applied based onCisco AV pair attribute rolevalue from Local Policy to aspecific client

Verify AVC profilethrough Localpolicy functionality

WLJ80S_AVC_35

PassedThis is to verify that AVCprofile is applied based onCisco AV pair attribute rolevalue from Local Policy to aspecific client with multiplematch types and action values

Verify AVC profilethrough Localpolicy functionalitywith multiple matchtypes and actionsenabled

WLJ80S_AVC_36

Rate LimitDefectsStatusDescriptionTitleLogical ID

PassedVerify if that CLIconfiguration for AVCprofile per applicationrate limiting isconfigurable asexpected and alsocheck in RADIUS(ACS)

Check AVC profile perapplication rate limitingconfiguration and DSCPmarking per applicationfromCLI using SSH alongwith RADIUS

WLJ80S_rate_01


56

New Features - Test SummaryRate Limit


PassedVerify if that CLIconfiguration for AVCprofile per applicationrate limiting isconfigurable asexpected and alsocheck in RADIUS(ACS)

Check AVC profile perapplication rate limitingconfiguration and DSCPmarking per applicationfrom CLI using Telnetalong with RADIUS

WLJ80S_rate_02

PassedVerify if that CLIconfiguration for AVCprofile per applicationrate limiting isconfigurable asexpected.

Check AVC profile perapplication rate limitingconfiguration and DSCPmarking per applicationfrom CLI

WLJ80S_rate_03

PassedVerify if that GUIconfiguration for AVCprofile per applicationrate limiting isconfigurable asexpected and alsocheck in RADIUS(ACS)

Check AVC profile perapplication rate limitingconfiguration and DSCPmarking per applicationfrom GUI along withRADIUS

WLJ80S_rate_04

PassedVerify if that AVC ratelimiting and DSCPdirection markingconfiguration fromSNMP

To check AVC ratelimiting and DSCPdirectional markingconfiguration from SNMP

WLJ80S_rate_05

PassedVerify if AVC ratelimiting, DSCPdirectional markingconfig and AVCbehavior after upgrade

Upgrade check for AVCrate limit and DSCPdirectional marking config

WLJ80S_rate_06

PassedVerify if AVC ratelimiting, DSCPdirectional markingconfig and AVCbehavior afterdowngrade

Downgrade check forAVC rate limit and DSCPdirectional marking config

WLJ80S_rate_07

PassedVerify if AVC ratelimiting config andAVC behavior afterconfig upload

Config upload check forAVC rate limit

WLJ80S_rate_08


57



PassedVerify if AVC ratelimiting config andAVC behavior afterconfig download

Config download check forAVC rate limit

WLJ80S_rate_09

PassedVerify if AVCraterlimit is applied forall the applicationconfigured and resultsare as expected.

Verify all rate limitapplication in a AVCprofile in 2500

WLJ80S_rate_10



WLJ80S_rate_11



WLJ80S_rate_12


Verify all rate limitapplication in a AVCprofile in WiSM2

WLJ80S_rate_13

PassedVerify if AVC ratelimit is applied afterper SSID bandwidthcontract values.

Check AVC rate limitingprecedence over Per SSIDBandwidth contract in2500

WLJ80S_rate_14



WLJ80S_rate_15



WLJ80S_rate_16


Check AVC rate limitingprecedence over Per SSIDBandwidth contract inWiSM2

WLJ80S_rate_17

PassedVerify if AVC ratelimit is applied afterper User bandwidthcontract values.

Check AVC rate limitingprecedence over Per UserBandwidth contract in2500

WLJ80S_rate_18


58





WLJ80S_rate_19



WLJ80S_rate_20


Check AVC rate limitingprecedence over Per UserBandwidth contract inWiSM2

WLJ80S_rate_21

PassedVerify if AVC ratelimit and directionalDSCP behavior with adot1x WLAN

Verify all rate limit anddirectional DSCPapplication in a dot1xWLAN using 2500

WLJ80S_rate_22



WLJ80S_rate_23



WLJ80S_rate_24


Verify all rate limit anddirectional DSCPapplication in a dot1xWLAN using WiSM2

WLJ80S_rate_25

PassedVerify if AVC ratelimit and directionalDSCP behavior with astatic PSKWLAN andno encryption WLAN

Verify all rate limit anddirectional DSCPapplication in a noencryption and static keyWLAN using 2500

WLJ80S_rate_26



WLJ80S_rate_27



WLJ80S_rate_28


59




Verify all rate limit anddirectional DSCPapplication in a noencryption and static keyWLAN using WiSM2

WLJ80S_rate_29

PassedVerify if AVC ratelimit and directionalDSCP behavior with awebauth WLAN

Verify all rate limit anddirectional DSCPapplication in a webauthWLAN using 2500

WLJ80S_rate_30



WLJ80S_rate_31



WLJ80S_rate_32


Verify all rate limit anddirectional DSCPapplication in a webauthWLAN using WiSM2

WLJ80S_rate_33

PassedVerify if AVC ratelimit behavior on aclient when the ratelimit rule changevalues dynamicallywhen the client is stillassociated with theAVC profile name

Verify AVC rate limitwhen the rate limit rulesdynamically using 2500

WLJ80S_rate_34


Verify AVC rate limitwhen the rate limit rulesdynamically 5500

WLJ80S_rate_35


Verify AVC rate limitwhen the rate limit rulesdynamically 8500

WLJ80S_rate_36


60




Verify AVC rate limitwhen the rate limit rulesdynamically WisM2

WLJ80S_rate_37

PassedVerify if DSCP valuesmarked based ondirection (eitherupstream /downstream) areupdated on the flowdata records sent innetflow

Verify AVC DSCPmarking with netflowusing 2500

WLJ80S_rate_38



WLJ80S_rate_39



WLJ80S_rate_40


Verify AVC DSCPmarking with netflowusing WiSM2

WLJ80S_rate_41


61


AAA Override for AVC Profile NameDefectsStatusDescriptionTitleLogical ID

PassedThis is to verify that AVCprofile is applied using AAAoverride from authenticationserver when the wlan iscentral switching.

Verify AVC profileAAA override fromauthenticationserver

WLJ80S_AAA_01

PassedThis is to verify that AVCprofile is applied using AAAoverride from authenticationserver when the wlan iscentral switching and splittunneling configured

Verify AVC profileAAA override fromauthenticationserver in asplit-tunnel wlanconfig

WLJ80S_AAA_02

PassedThis is to verify that AVCprofile is applied using AAAoverride from authenticationserver when the WLAN isL3 enabled.

Verify AVC profileAAA override fromauthenticationserver

WLJ80S_AAA_03

PassedThis is to verify that AVCprofile is applied using AAAoverride from authenticationserver when the wlan isconfigured for mac filtering

Verify AVC profileAAA override fromauthenticationserver when wlan isconfigured for macfiltering

WLJ80S_AAA_04

PassedThis is to verify that AVCprofile is applied using AAAoverride from ISE whenclient goes through CWA /posturing.

Verify AVC profileAAA override withRadius NACenabled

WLJ80S_AAA_05

PassedThis is to verify that AVCprofile is applied using AAAoverride from authenticationserver even after sessiontimeout is expired.

Check if afterre-authenticationAVC profile is stillapplied to the client.

WLJ80S_AAA_06

PassedTo validate AAA overrideRadius session time out

To validate AAAoverride Radiussession time out

WLJ80S_AAA_07

PassedThis is to verify that thesame AVC profile is appliedusing AAA override fromauthentication server evenafter session timeout isexpired.

Check if afterre-authenticationAVC profile is stillapplied to the clienteven if the AVCname change on theAAA.

WLJ80S_AAA_08


62

New Features - Test SummaryAAA Override for AVC Profile Name


PassedThis is to verify that AVCprofile is applied using AAAoverride from authenticationserver accordingly with maxnumber of clients.

Verify AVC profileAAA override fromauthenticationserver with maxnumber of clients

WLJ80S_AAA_09

PassedThis is to verify the AVCprofile behavior whenapplied from AAA with aninvalid name which is notconfigured on the WLC.

Verify AVC profileAAA override fromauthenticationserver with invalidprofile name

WLJ80S_AAA_10

PassedThis is to verify the AVCprofile behavior whenapplied from AAA withadditional attributes likeACL name, session timeoutand Vlan id.

Verify AVC profileAAA override fromauthenticationserver withadditional AAAattributes like Vlan,session timeout andACL name

WLJ80S_AAA_11

PassedThis is to verify the AVCprofile behavior whenapplied from AAA withadditional attributes likeACL name, session timeoutand Vlan id.

Verify AVC profileAAA override fromauthenticationserver with radiusfailover

WLJ80S_AAA_12

PassedThis is to verify the AVCprofile behavior whenapplied from AAA whenAAA override is disabled onthe wlan, but AAA serverreturning a AVC profilename

Verify AVC profileAAA override fromauthenticationserver with AAAoverride disabledfor the wlan

WLJ80S_AAA_13

PassedThis is to verify that AVCprofile is applied from localpolicy based on Cisco AVpair attribute role value to aspecific client when AAAoverride is enabled isenabled and cisco-av-pairAVC-profile-name and rolename attribute is receivedafter authentication fromAAA server

Verify AVC profilethrough Localpolicy functionalitywhenAAAoverrideenabled andAVC-profile-nameis configured on theAAA

WLJ80S_AAA_14


63

New Features - Test SummaryAAA Override for AVC Profile Name


PassedThis is to verify that AVCprofile is applied from localpolicy based on Cisco AVpair attribute role value to aspecific client when AAAoverride is disabled andcisco-av-pairAVC-profile-name and rolename attribute is receivedafter authentication fromAAA server

Verify AVC profilethrough Localpolicy functionalitywhenAAAoverridedisabled andAVC-profile-nameis configured on theAAA

WLJ80S_AAA_15

PassedThis is to verify that AVCprofile is applied fromdefault wlan AVC profilename when role andAVC-profile-name is notconfigured on the AAAserver and local policyconfigured on the WLANwith a AVC profile name

Verify AVC profilethrough Localpolicy functionalitywhenAAAoverridedisabled andAVC-profile-nameand role is notconfigured on theAAA

WLJ80S_AAA_16

Rf ProfileDefectsStatusDescriptionTitleLogical ID

PassedTo Configure few channelson Global DCA list. Try toconfigure a channel on RFprofile DCA list which is notpart of Global list via theGUI. Verify GUI throwserror

RF profile DCAlist-GUI

WLJ80S_RF_01

PassedTo Configure few channelson Global DCA list. Try toconfigure a channel on RFprofile DCA list which is notpart of Global list via theCLI. Verify CLI throws error

RF profile DCAlist-CLI

WLJ80S_RF_02

Passed"To Verify the CLI -""showrf-profile details<RF-Profile>"", showsparameters configured forDCA and Threshold fortraps."

Show CLIcommand related toRF profile for DCAfeature

WLJ80S_RF_03


64

New Features - Test SummaryRf Profile


PassedTo Verify Config issuccessfully uploaded andCW is seen as 20 MHz.Change the channel width to40 MHz on the uploadedconfig. Download thechanged config and verifyCW on RF profile is set to 40MHz

Upload / Downloadof the Config andcheck for Channelwidth parameter onDCA RF profile

WLJ80S_RF_04

PassedTo Configure various RFprofile DCA parameters viathe CLI and verify configsare successful

Configure RFprofile DCAparameters via theCLI

WLJ80S_RF_05

PassedVerify Config is successfullyuploaded and Avoid ForeignAP interference is seen asenabled.

Upload/Downloadof the Config andcheck for AvoidForeign APinterferenceparameter on DCARF profile

WLJ80S_RF_06

PassedTo Verify config issuccessfully uploaded.Change few threshold valueson uploaded config.Download the config andverify the changed values

Upload/Downloadof the Config andcheck for thresholdtrap values on RFprofile

WLJ80S_RF_07

PassedTo Configure variousthreshold for traps via theGUI and verify configs aresuccessful

RF profile,threshold for trapsvia the GUI

WLJ80S_RF_08

PassedTo Configure various RFprofile DCA parameters viathe CLI and verify configsare successful

RF profile DCAparameters via theCLI

WLJ80S_RF_09

PassedTo verify Configure variousRF profile DCA parametersvia the GUI and verifyconfigs are successful

RF profile DCAparameters via theGUI

WLJ80S_RF_10

PassedTo verify Configure variousthreshold for traps via theCLI and verify configs aresuccessful

RF profile,threshold for trapsvia the CLI

WLJ80S_RF_11


65

New Features - Test SummaryRf Profile


PassedTo verify Configure variousthreshold for traps via theGUI and verify configs aresuccessful


WLJ80S_RF_12

PassedConfigure DCA andthreshold for traps on RFprofile. Reset the Controllerand verify the configs areretained

Controller shouldretain the configacross controllerreset

WLJ80S_RF_13

Cleanair-skyrosDefectsStatusDescriptionTitleLogical ID

PassedTo verify if the cleanAirfunctionality can beenabled/disabled from theGUIof the WLC

Enable/DisableCleanAir in the GUIof 5508 andWiSM2controller.

WLJ80S_CAE_01

PassedTo verify if the cleanAirfunctionality can beenabled/disabled from theGUIof the WLC

Enable/DisableCleanAir in the GUIof 7500 and 8500controller.

WLJ80S_CAE_02

PassedTo verify if the cleanAirfunctionality can beenabled/disabled from the CLIof the WLC

Enabling/disablingCleanAir from theCLI of 5508 andWiSM2 controllers

WLJ80S_CAE_03

PassedTo verify if the cleanAirfunctionality can beenabled/disabled from the CLIof the WLC

Enabling/disablingCleanAir from theCLI of 7500 and8500 controllers

WLJ80S_CAE_04

PassedTo verify if the AP is able todetect Bluetooth interferencesin the 802.11b/g/n range.

Detecting Bluetoothinterferences using1600 AP in 5508and WiSM2controllers

WLJ80S_CAE_05

PassedTo verify if the AP is able todetect Bluetooth interferencesin the 802.11b/g/n range.

Detecting Bluetoothinterferences using1600 AP in7500/8500controllers

WLJ80S_CAE_06


66

New Features - Test SummaryCleanair-skyros


PassedTo verify if the alarm iftriggered if the Air Qualityreaches the threshold value orbelow in a controller where the1600 AP is associated

Air Quality Indextrap after setting theAQI alarm thresholdin the 5508 andWiSM2 controller towhich a 1600 AP isassociated

WLJ80S_CAE_07

PassedTo verify if the alarm iftriggered if the Air Qualityreaches the threshold value orbelow in a controller where the1600 AP is associated

Air Quality Indextrap after setting theAQI alarm thresholdin the 7500/8500controller to whicha 1600 AP isassociated

WLJ80S_CAE_08

PassedTo enable trap for unclassifiedinterferences, set the thresholdfor the same and verify if thetrap is passed for bluetoothand other interference types

Trap for unclassifiedinterferences using1600 AP associatedto the 5508/WiSM2controller

WLJ80S_CAE_09

PassedTo enable trap for unclassifiedinterferences, set the thresholdfor the same and verify if thetrap is passed for bluetoothand other interference types

Trap for unclassifiedinterferences using1600 AP associatedto the 7500/8500controller

WLJ80S_CAE_10

PassedTo verify if the RRM initiatedDCA which changes thechannel of the affected accesspoint radio if possible toimprove network performancewhen the interference for theaccess point rises above thethreshold level

Trigger spectrumevent-driven radioresourcemanagement (RRM)when a CleanAirenabled 1600 AP isassociated to5508/WiSM2controller

WLJ80S_CAE_11

PassedTo verify if the RRM initiatedDCA which changes thechannel of the affected accesspoint radio if possible toimprove network performancewhen the interference for theaccess point rises above thethreshold level

Trigger spectrumevent-driven radioresourcemanagement (RRM)when a CleanAirenabled 1600 AP isassociated to7500/8500controller

WLJ80S_CAE_12


67



PassedTo verify if the CleanAirconfiguration on the AP pageis correctly and the changesreflect.

Enabling CleanAirfrom the Accesspoint configure pagein 1600 AP

WLJ80S_CAE_13

PassedTo verify if the interferencesdetected by 1600 AP can becorrectly monitored from theWLC GUI.

MonitoringInterference devicefrom the ControllerGUI

WLJ80S_CAE_14

PassedTo verify if the persistentdevices could be monitored ona specific 1600 Series AccessPoint

Monitor Persistentdevices on a 1600Access Point

WLJ80S_CAE_15

PassedTo verify if the AP is able todetect Wifi directinterferences.

Detecting Wifidirect interferencesusing 1600 AP in5508 and WiSM2controllers

WLJ80S_CAE_16

PassedTo verify if the AP is able todetect Wifi directinterferences.

Detecting Wifidirect interferencesusing 1600 AP in7500/8500controllers

WLJ80S_CAE_17

PassedTo verify if the Air Quality ifRadio bands can be viewedfrom the GUI of controller andCLI.

Monitoring the AirQuality of RadioBands from the5508/WiSM2Controller GUI andCLI

WLJ80S_CAE_18

PassedTo verify if the Air Quality ifRadio bands can be viewedfrom the GUI of controller andCLI.

Monitoring the AirQuality of RadioBands from the7500/8500Controller GUI andCLI

WLJ80S_CAE_19

PassedTo verify if the Cisco PrimeInfrastructure report forCleanAir is generatedcorrectly .

Cisco PrimeInfrastructureReports on CleanAir

WLJ80S_CAE_20

PassedTo verify if the location of theknown non-WiFi interferers isdetected by the CleanAirenabled 1600 series AP

Location of knownnon-WiFi interferersusing a CleanAirenabled 1600 seriesAP

WLJ80S_CAE_21


68



PassedTo verify if the SE-connectmode can be turned on in aCleanAir enabled 1600 seriesAP

SE-Connectmode inCleanAir enabled1600 series AP

WLJ80S_CAE_22

PassedTo verify if we can obtaindetailed spectrum data that canbe used to generate RFanalysis plots similar to thoseprovided by a spectrumanalyzer.

CleanAir enabled1600 AP forSpectrum Expertfunction

WLJ80S_CAE_23

PassedTo verify if the SpectrumExpert enabling done from thePI is working fine

CleanAir enabled1600 AP forSpectrum Expertfunction enablingfrom Cisco PrimeInfrastructure

WLJ80S_CAE_24

Flexconnect on MeshDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether changing theAP mode from local toflex+bridge works properly

AP conversion fromLocal toFlex+bridge mode

WLJ80S_Mesh_01

PassedTo verify whether changing theRAPmode fromFlexconnect toFlex+bridge works properly

AP conversion fromFlexconnect toFlex+bridge modefor RAP

WLJ80S_Mesh_02

PassedTo verify whether changing theMAP mode from Flexconnectto Flex+bridge works properly

AP conversion fromFlexconnect toFlex+bridge modefor MAP

WLJ80S_Mesh_03

PassedTo verify whether changing themode from flexconnect toFlex+bridge works properly forRAP/MAP

AP conversion fromFlexconnect toFlex+bridge modefor RAP/MAP

WLJ80S_Mesh_04

PassedTo verify all the showcommands for Flex+bridgemode

Showcommands forFlex+bridge mode

WLJ80S_Mesh_05


69

New Features - Test SummaryFlexconnect on Mesh


PassedTo verify the VLAN/WLANmapping for flexconnect groupwith local-switching

VLAN/WLANmapping forflexconnectlocal-switching

WLJ80S_Mesh_06

PassedTo verify the default AP groupwith VLAN/WLAN mapping

Default AP groupwithVLAN/WLANmapping

WLJ80S_Mesh_07

PassedTo verify whether the AP moderetains after upgrading theWLCto latest software

AP mode afterupgrade

WLJ80S_Mesh_08

PassedTo verify the VLAN/WLANmapping config for flexconnectLS after WLC reset

VLAN/WLANmapping configupon WLC reset

WLJ80S_Mesh_09

PassedTo verify the client statusClient status whenFlex+bridge AP isin standalone mode

WLJ80S_Mesh_10

CleanairDefectsStatusDescriptionTitleLogical ID

PassedTo verify the Airt eventdriven RRM

Clean Air EventDriven RRM

WLJ80S_CleanAir_01

PassedTo verify the Air Qualityupdates

Confirm Air Qualityupdates are sent byaccess points

WLJ80S_CleanAir_02

PassedVerify if a Bluetooth isdetected by AP / WLC inFlexconnect mode.

Interferencedetection in FlexConnect

WLJ80S_CleanAir_03

OEAP Enhancements

Basic Firewall


PassedTo check whetherOEAP gets joined ornot with 5500WLC

Associating OEAPto 5500 WLC

WLJ80S_OEAP_BF_01


70

New Features - Test SummaryCleanair


PassedTo check whetherFirewall is gettingenabled or not inOEAP GUI.

Enabling theFirewall in OEAPGUI.

WLJ80S_OEAP_BF_02

PassedTo check whetherLan clients access isdenied or not afterenabling Firewall inOEAP GUI.

Enabling theFirewall in OEAPGUI and checkingthe internet accessfor a Lan client.

WLJ80S_OEAP_BF_03

PassedTo check whetherHTTP & HTTPSapplication accessare allowed or notfor a Lan client.

Enabling the Lanapplication accessfor HTTP&HTTPSin OEAP GUI.

WLJ80S_OEAP_BF_04

PassedTo check whetherTFTP & Telnetapplication accessare allowed or notfor a Lan clientwhen it is connectedto Lan port no.1

Enabling the Lanapplication accessfor TFTP & Telnetin OEAP GUI.

WLJ80S_OEAP_BF_05

PassedTo check whetherall three clients getsdenied or not whenFirewall is enabled.

Associating threeLan clients andchecking theFirewall function

WLJ80S_OEAP_BF_06

PassedTo check whetherspecific Lan ipaddress access tointernet is denied ornot by configuringip address in PortForwarding.

Denying specificLan ip address usingport forwardingrules

WLJ80S_OEAP_BF_07

PassedTo check whetherspecific Lan ipaddress access tointernet is allowedor not byconfiguring ipaddress in PortForwarding.

Allowing specificLan ip address usingport forwardingrules

WLJ80S_OEAP_BF_08

PassedTo check whetherclient is connectedor not to LocalWLAN created inOEAP GUI.

Creating LocalWLAN andassociating a clientto this LocalWLAN.

WLJ80S_OEAP_BF_09


71

New Features - Test SummaryOEAP Enhancements


PassedTo check whetherFirewall gettingapplied to LocalWLAN client ornot.

Checking theFirewall function toa Local WLANclient

WLJ80S_OEAP_BF_10

PassedTo check whetherHTTP & HTTPSapplication accessare allowed or notfor a Local WLANclient.

Enabling the Lanapplication accessfor HTTP&HTTPSin OEAP GUI andchecking for LocalWLAN client

WLJ80S_OEAP_BF_11

PassedTo check whetherTFTP & Telnetapplication accessare allowed or notfor a Local WLANclient.

Enabling the Lanapplication accessfor TFTP & Telnetin OEAP GUI andchecking for LocalWLAN client.

WLJ80S_OEAP_BF_12

PassedTo check whetherFirewall functionworks or not in Win7 client byassociating it toPersonal SSID inOEAP withSecurity-MacFiltering.

EnablingMac Filterin OEAP GUI andchecking theFirewall functionfor Win 7 Client byadding its Macaddress.

WLJ80S_OEAP_BF_13

PassedTo check whetherFirewall functionworks or not in Win8 client byassociating it toPersonal SSID inOEAP withSecurity-MacFiltering.

EnablingMac Filterin OEAP GUI andchecking theFirewall functionfor Win 8 Client byadding its Macaddress.

WLJ80S_OEAP_BF_14

PassedTo check whetherFirewall functionworks or not inMacBook client byassociating it toPersonal SSID inOEAP withSecurity-MacFiltering.

EnablingMac Filterin OEAP GUI andchecking theFirewall functionforMacBook Clientby adding its Macaddress.

WLJ80S_OEAP_BF_15


72



PassedTo check whetherFirewall functionworks or not inSamsung S4 clientby associating it toPersonal SSID inOEAP withSecurity-MacFiltering.

EnablingMac Filterin OEAP GUI andchecking theFirewall functionfor Samsung S4Client by adding itsMac address.

WLJ80S_OEAP_BF_16

PassedTo check whetherFirewall functionworks or not inApple Iphone clientby associating it toPersonal SSID inOEAP withSecurity-MacFiltering.

EnablingMac Filterin OEAP GUI andchecking theFirewall functionfor Apple IphoneClient by adding itsMac address.

WLJ80S_OEAP_BF_17

PassedTo verify whetherFirewall functionsworks or not forWin 7 clientassociated toPersonal SSID withSecurity -WPA2+PSK.

Associating Win 7client to PersonalSSID -WPA2+PSKand checking thefirewall function.

WLJ80S_OEAP_BF_18

PassedTo verify whetherFirewall functionsworks or not forMacBook clientassociated toPersonal SSID withSecurity -WPA2+PSK.

AssociatingMacBook client toPersonal SSID-WPA2+PSK andchecking thefirewall function.

WLJ80S_OEAP_BF_19

PassedTo check whetherclient able to accessthe internet or notvia DMZ.

Creating a DMZ ipaddress andchecking itsfunction.

WLJ80S_OEAP_BF_20


73


End User GUI Enhancements


PassedTo check whether NetworkDiagnostics tab is present or notin WLC GUI for OEAP.

Associating OEAPto 5500 WLC andchecking theNetworkDiagnostics tab inWLC GUI

WLJ80S_OEAP_UI_01

PassedTo check whether networkdiagnostics works or not inOEAP GUI.

Starting theNetworkDiagnostics inOEAP GUI

WLJ80S_OEAP_UI_02

PassedTo check whether networkdiagnostics works or not in 7500WLC GUI.

Starting theNetworkDiagnostics in 7500WLC GUI

WLJ80S_OEAP_UI_03

PassedTo check whether networkdiagnostics works or not in 7500WLC CLI.

Starting theNetworkDiagnostics in 7500WLC CLI

WLJ80S_OEAP_UI_04



WLJ80S_OEAP_UI_05



WLJ80S_OEAP_UI_06



WLJ80S_OEAP_UI_07



WLJ80S_OEAP_UI_08

PassedTo check whether networkdiagnostics works or not inWiSM2 GUI.

Starting theNetworkDiagnostics inWiSM2 GUI

WLJ80S_OEAP_UI_09

PassedTo check whether networkdiagnostics works or not inWiSM2 CLI.

Starting theNetworkDiagnostics in 8500WiSM2 CLI

WLJ80S_OEAP_UI_10


74


Split Tunnel for Internet Traffic


PassedTo check whether split tunnelconfiguration is enabledglobally or not in WLC.

Enabling Splittunnel configurationglobally.

WLJ80S_OEAP_ST_01

PassedTo check whether OEAP ACLis created and mapped to aWLAN successfully or not inWLC GUI.

Creating a OEAPACL in WLC GUIand mapping it to aWLAN.

WLJ80S_OEAP_ST_02

PassedTo check whether OEAP ACLis created and mapped to aWLAN successfully or not inWLC CLI.

Creating a OEAPACL in WLC CLIand mapping it to aWLAN.

WLJ80S_OEAP_ST_03

PassedTo check whether Win 7 clientassociated successfully to theWLAN in 7500 WLC and ableto access the internet viagateway as mentioned inWLAN under OEAPparameters.

Associating aWin 7client to aWLAN inwhich split tunnel isenabled in 7500WLC

WLJ80S_OEAP_ST_04

PassedTo check whether MacBookclient associated successfullyto the WLAN in 7500 WLCand able to access the internetvia gateway as mentioned inWLAN under OEAPparameters.

Associating aMacbook client to aWLAN in whichsplit tunnel isenabled in 7500WLC

WLJ80S_OEAP_ST_05



WLJ80S_OEAP_ST_06

PassedTo check whether Samsung S4client associated successfullyto the WLAN in 7500 WLCand able to access the internetvia gateway as mentioned inWLAN under OEAPparameters.

Associating aSamsung S4 clientto a WLAN inwhich split tunnel isenabled in 7500WLC

WLJ80S_OEAP_ST_07


75



PassedTo checkwhether Apple Iphoneclient associated successfullyto the WLAN in 7500 WLCand able to access the internetvia gateway as mentioned inWLAN under OEAPparameters.

Associating AppleIphone client to aWLAN in whichsplit tunnel isenabled in 7500WLC

WLJ80S_OEAP_ST_08



WLJ80S_OEAP_ST_09



WLJ80S_OEAP_ST_10



WLJ80S_OEAP_ST_11

PassedTo check whether Samsung S4client associated successfullyto the WLAN in 5500 WLCand able to access the internetvia gateway as mentioned inWLAN under OEAPparameters.

Associating aSamsung S4 clientto a WLAN inwhich split tunnel isenabled in 5500WLC

WLJ80S_OEAP_ST_12

PassedTo checkwhether Apple Iphoneclient associated successfullyto the WLAN in 5500 WLCand able to access the internetvia gateway as mentioned inWLAN under OEAPparameters.

Associating AppleIphone client to aWLAN in whichsplit tunnel isenabled in 5500WLC

WLJ80S_OEAP_ST_13


76





WLJ80S_OEAP_ST_14



WLJ80S_OEAP_ST_15

Voice QOS Enhancements


PassedTo check whether OEAPQueue stats are present or notin Radio's detail page of 7500WLC GUI for OEAP.

Associating OEAPto 5500 WLC andchecking the Radiostatistics page inWLC GUI.

WLJ80S_OEAP_QOS_01

PassedTo check whether OEAPQueue stats are present or notin Radio's detail page of 7500WLC GUI for OEAP.

Associating OEAPto 7500 WLC andchecking the Radiostatistics page inWLC GUI.

WLJ80S_OEAP_QOS_02

PassedChecking the voice packetsstats in Radio details page of5500 WLC GUI whenconnecting voice clients toOEAP and passing the voicetraffic between the clients.

Associating voiceclients to OEAP andchecking the Radiostatistics page in5500 WLC GUI.

WLJ80S_OEAP_QOS_03

PassedChecking the voice packetsstats in 5500 WLC CLI whenconnecting voice clients toOEAP and passing the voicetraffic between the clients.

Associating voiceclients to OEAP andchecking the Radiostatistics page in5500 WLC CLI.

WLJ80S_OEAP_QOS_04

PassedChecking the video packetsstats in Radio details page of5500 WLC GUI whenconnecting video clients toOEAP.

Associating videoclients to OEAP andchecking the Radiostatistics page in5500 WLC GUI.

WLJ80S_OEAP_QOS_05


77



PassedChecking the video packetsstats in Radio details page of5500 WLC CLI whenconnecting video clients toOEAP.

Associating videoclients to OEAP andchecking the Radiostatistics page in5500WLC CLI.

WLJ80S_OEAP_QOS_06

PassedChecking the voice packetsstats in Radio details page of7500 WLC GUI whenconnecting voice clients toOEAP and passing the voicetraffic between the clients.

Associating voiceclients to OEAP andchecking the Radiostatistics page in7500 WLC GUI.

WLJ80S_OEAP_QOS_07

PassedChecking the voice packetsstats in 7500 WLC CLI whenconnecting voice clients toOEAP and passing the voicetraffic between the clients.

Associating voiceclients to OEAP andchecking the Radiostatistics page in7500 WLC CLI.

WLJ80S_OEAP_QOS_08

PassedChecking the video packetsstats in Radio details page of7500 WLC GUI whenconnecting video clients toOEAP.

Associating videoclients to OEAP andchecking the Radiostatistics page in7500 WLC GUI.

WLJ80S_OEAP_QOS_09

PassedChecking the video packetsstats in Radio details page of7500 WLC CLI whenconnecting video clients toOEAP.

Associating videoclients to OEAP andchecking the Radiostatistics page in7500 WLC CLI.

WLJ80S_OEAP_QOS_10

L2TPv3 over UDPDefectsStatusDescriptionTitleLogical ID

PassedTo verify the L2TPv3 overUDP configuration in AP

L2TPV3 over UDPconfiguration

WLJ80S_L2TPv3_01

PassedTo verify whether tunnelstatus is Up

l2tpv3 over UDPtunnelestablishment-AP3500

WLJ80S_L2TPv3_02


78

New Features - Test SummaryL2TPv3 over UDP

3700 Autonomous APDefectsStatusDescriptionTitleLogical ID

PassedVerify client associationClient Associationwith no security

WLJ80S_aap_01

PassedVerify client associationClient Associationwith WEP

WLJ80S_aap_02

PassedVerify client associationClient Associationwith WPA

WLJ80S_aap_03

PassedVerify WGB associationWGB ModeWLJ80S_aap_04

PassedVerify the Autonomous APmanagement access

Autonomous APmanagement access

WLJ80S_aap_05

PassedTo Verify the Traffic flowbetween two wireless clients

Traffic flow betweentwo wireless clients

WLJ80S_aap_06

PassedTo verify the connected clientin AP management page

Monitoring ofconnected client

WLJ80S_aap_07

PassedTo verify the Trap Logs forconnected client

Trap logs forconnected client

WLJ80S_aap_08

PassedTo verify the management usercreation

Management usersWLJ80S_aap_09

PassedTo verify the radioenable/disable status

Enabling/Disablingthe radio

WLJ80S_aap_10

PassedVerify client associationClient Associationwith TKIP

WLJ80S_aap_11

PassedVerify client associationClient Associationwith AES-CCMP

WLJ80S_aap_12

PassedVerify client associationClient Associationwith TKIP +WEP

WLJ80S_aap_13

PassedVerify Transmit and Receiveantenna

Transmit and Receiveantenna

WLJ80S_aap_16

PassedVerify the client associationafter changing the data rates

Data rates changeWLJ80S_aap_17

PassedTo verify the CDP neighbordetails

CDP neighbor detailsWLJ80S_aap_18


79

New Features - Test Summary3700 Autonomous AP

11ac CCX LiteDefectsStatusDescriptionTitleLogical ID

PassedTo verify the CCX IE contentfrom 11ac interface

CCX IE verificationWLJ80S_CCX_01

PassedTo verify the initial clientassociation with CCKMenabled-Netgear client

Initial Clientassociation withCCKMenabled-Netgear client

WLJ80S_CCX_04

PassedTo verify the Fastre-authenticationwith CCKMenabled under roamingconditions- Netgear client

Fast re-authenticationof 11ac client withCCKMenabled-Netgear client

WLJ80S_CCX_07

MSE

CMX Visitor ConnectDefectsStatusDescriptionTitleLogical ID

PassedTo verify created NewTemplate Field is listed in theSplash Templates Tab or not

Creating TemplateFields in CMXConnect and EngageUI

WLJ80S_Visitor_01

PassedTo verify whether Editing theexisting Template Field inCMXConnect and EngageUIis successful or not

Editing TemplateFields in CMXConnect and EngageUI

WLJ80S_Visitor_02

PassedTo verify whether Deletingthe existing Template Field inCMXConnect and EngageUIis successful or not

Deleting TemplateFields in CMXConnect and EngageUI

WLJ80S_Visitor_03

PassedTo verify created New SocialConnector is listed in theSplash Templates Tab or not

Creating SocialConnectors in CMXConnect and EngageUI

WLJ80S_Visitor_04

PassedTo verify whether Editing theexisting Social Connectors inCMXConnect and EngageUIis successful or not

Editing SocialConnectors in CMXConnect and EngageUI

WLJ80S_Visitor_05


80

New Features - Test Summary11ac CCX Lite


PassedTo verify whether Deletingthe existing Social Connectorsin CMX Connect and EngageUI is successful or not

Deleting SocialConnectors in CMXConnect and EngageUI

WLJ80S_Visitor_06

PassedTo verify creation of NewSplash Template is successfulor not

Creating SplashTemplates in CMXConnect and EngageUI

WLJ80S_Visitor_07

PassedTo verify Editing the existingSplash Template is successfulor not

Editing SplashTemplates in CMXConnect and EngageUI

WLJ80S_Visitor_08

PassedTo verify Deleting the existingSplash Template is successfulor not

Deleting SplashTemplates in CMXConnect and EngageUI

WLJ80S_Visitor_09

PassedTo verify displaying of SplashTemplates assigned to theSocial Connectors issuccessful or not

Splash Templatesassigned to theSocial Connectors

WLJ80S_Visitor_10

PassedTo verify assignation ofSplash Template to a Floor issuccessful or not

Assigning a SplashTemplate to a floor

WLJ80S_Visitor_11

PassedTo verify whether DefaultUser Groups are Displayed inCMXConnect and EngageUIor not

Default User GroupsWLJ80S_Visitor_12

PassedTo verify the Redirection of aclient to the Splash Page issuccessful or not

User GroupsWLJ80S_Visitor_13

PassedTo verify whether Basic Useris de-authentication afterusing 100 MB or not


PassedTo verify whether Social Useris de-authentication afterusing 500 MB or not


PassedTo verify whether the MSEissues NMSP Message forDe-auth Packet or not

NMSP Message forDe-authenticatingwindow 7 client

WLJ80S_Visitor_16


81

New Features - Test SummaryCMX Visitor Connect



NMSP Message forDe-authenticatingApple mac bookclient

WLJ80S_Visitor_17


NMSP Message forDe-authenticatingApple iphone client

WLJ80S_Visitor_18


NMSP Message forDe-authenticatingSamsung s4 mobileclient

WLJ80S_Visitor_19

PassedTo verify that the Bandwidthis tracked or not when theLimit is set to Zero

User BandwidthWLJ80S_Visitor_20

PassedTo verify Whether NewWindows 7 Visitors areDisplayed in the CMXConnect and Engage UI or not

New Windows 7Visitors

WLJ80S_Visitor_21

PassedTo verifyWhether NewApplemac book Visitors areDisplayed in the CMXConnect and Engage UI or not

New Apple macbook Visitors

WLJ80S_Visitor_22

PassedTo verifyWhether NewAppleiphone Visitors are Displayedin the CMX Connect andEngage UI or not

New Apple iphoneVisitors

WLJ80S_Visitor_23

PassedTo verify Whether NewSamsung s4 mobile Visitorsare Displayed in the CMXConnect and Engage UI or not

New Samsung s4mobile Visitors

WLJ80S_Visitor_24

PassedTo verify Whether RepeatedWindows 7 Visitors areDisplayed in the CMXConnect and Engage UI or not

Repeated Windows7 Visitors

WLJ80S_Visitor_25

PassedTo verify Whether RepeatedApple mac book Visitors areDisplayed in the CMXConnect and Engage UI or not

Repeated Apple macbook Visitors

WLJ80S_Visitor_26

PassedTo verify Whether RepeatedApple iphone Visitors areDisplayed in the CMXConnect and Engage UI or not

Repeated Appleiphone Visitors

WLJ80S_Visitor_27


82

New Features - Test SummaryCMX Visitor Connect


PassedTo verify Whether RepeatedSamsung s4 mobile Visitorsare Displayed in the CMXConnect and Engage UI or not

Repeated Samsungs4 mobile Visitors

WLJ80S_Visitor_28

PassedTo verify Whether ActiveWindows 7 Visitors areDisplayed in the CMXConnect and Engage UI or not

Active Windows 7Visitors

WLJ80S_Visitor_29

PassedTo verify Whether ActiveApple mac book Visitors areDisplayed in the CMXConnect and Engage UI or not

Active Apple macbook Visitors

WLJ80S_Visitor_30

PassedTo verify Whether ActiveApple iphone Visitors areDisplayed in the CMXConnect and Engage UI or not

Active Apple iphoneVisitors

WLJ80S_Visitor_31

PassedTo verify Whether ActiveSamsung s4 mobile Visitorsare Displayed in the CMXConnect and Engage UI or not

Active Samsung s4mobile Visitors

WLJ80S_Visitor_32

Real-PathDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether all the real pathconfiguration icons function forthe selected floor

Real pathconfiguration iconsfunction for theselected floor

WLJ80S_MSE_RP_01

PassedTo verify whether can import thepath created and saved

Imports the pathcreated

WLJ80S_MSE_RP_02

CSCuo53852FailedTo verify whether can export thepath created

Export the pathoutputs

WLJ80S_MSE_RP_03

PassedTo verify whether clear functionis working fine

Clear function forthe real path

WLJ80S_MSE_RP_04

PassedTo verify whether reload functionis working fine when saved thereal paths created

Reload function forthe real path withsaved

WLJ80S_MSE_RP_05

PassedTo verify whether reload functionis working fine without save thereal paths created

Reload function forthe real pathwithout saved

WLJ80S_MSE_RP_06


83

New Features - Test SummaryReal-Path

Zone Based AnalyticsDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether ZoneBasedAnalytics using LocalAPs with L2 roaming on thesame floor able to roam andpass the traffic successfully

Zone-BasedAnalytics, Local APL2 Roaming, Samefloor

WLJ80S_MSE_ZB_01

PassedTo verify whether ZoneBasedAnalytics using LocalAPs with L3 roaming on thesame floor able to roam andpass the traffic successfully

Zone-BasedAnalytics, Local APL3 Roaming, Samefloor

WLJ80S_MSE_ZB_02

PassedTo verify whether ZoneBasedAnalytics using LocalAPs with L2 roaming on thedifferent floor able to roamand pass the trafficsuccessfully

Zone-BasedAnalytics, Local APL2 Roaming,Different floors

WLJ80S_MSE_ZB_03

PassedTo verify whether ZoneBasedAnalytics using LocalAPs with L3 roaming on thedifferent floor able to roamand pass the trafficsuccessfully

Zone-BasedAnalytics, Local APL3 Roaming,Different floors

WLJ80S_MSE_ZB_04

PassedTo verify whether ZoneBased Analytics using FlexAPs with L2 roaming onsame floor able to roam andpass the traffic successfully

Zone-BasedAnalytics, Flex APL2 Roaming, Samefloor

WLJ80S_MSE_ZB_05

PassedTo verify whether ZoneBased Analytics using FlexAPs with L3 roaming onsame floor able to roam andpass the traffic successfully

Zone-BasedAnalytics, Flex APL3 Roaming, Samefloor

WLJ80S_MSE_ZB_06

PassedTo verify whether ZoneBased Analytics using FlexAPs with L2 roaming withdifferent floor able to roamand pass the trafficsuccessfully

Zone-BasedAnalytics, Flex APL2 Roaming,Different floor

WLJ80S_MSE_ZB_07


84

New Features - Test SummaryZone Based Analytics


PassedTo verify whether ZoneBased Analytics using FlexAPs with L3 roaming withdifferent floor able to roamand pass the trafficsuccessfully

Zone-BasedAnalytics, Flex APL3 Roaming,Different floor

WLJ80S_MSE_ZB_08

CMX NAPP StoreDefectsStatusDescriptionTitleLogical ID

PassedTo verify all web apps andservices are displayed in theMSE admin view or not

Checking MSEadmin view UI

WLJ80S_NAPP_01

PassedTo verify whether web appscan be dragged and droppedin the MSE admin view UI

Moving web appinside the MSEadmin view UI

WLJ80S_NAPP_02

PassedTo verify creation of newfolder in CMX NAPP Storein virtual MSE is successfulor not

Creating new folderinMSE admin viewUI

WLJ80S_NAPP_03

PassedTo verify whether or not anyparticular web app is returnedonce after the search iscompleted successfully

Search bar in CMXNAPP Store

WLJ80S_NAPP_04

PassedTo verify that all the updatesare listed in the admin viewor not

Updates in MSEadmin view UI

WLJ80S_NAPP_05

PassedTo verify whether What'sNew ? App is successfullylaunched

What's New? AppinMSE admin viewUI

WLJ80S_NAPP_06

PassedTo verify whether settingspage is loaded successfullyfrom the admin view UI ofMSE or not

Settings app inMSE admin viewUI

WLJ80S_NAPP_07

PassedTo verify whether trapdestinations can be newlyadded from the settings appor not

Adding trapdestination insettings applaunched fromMSEadmin view UI

WLJ80S_NAPP_08


85

New Features - Test SummaryCMX NAPP Store


PassedTo verify whether logs issuccessfully downloadedfrom the settings app or not

Downloading logsfrom settings applaunched fromMSEadmin view UI

WLJ80S_NAPP_09

PassedTo verify successful creationof a wish and sendingfeedback

Creating a wish andsending feedback

WLJ80S_NAPP_10

702 APDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether702 AP is joined ornot with 2500Controller

Joining 702 AP to2500 Controller

WLJ80S_702AP_01

PassedTo verify whetherclient getsconnected or not toa WLC using 702APwith L2 Security- WEP using 2500

Associating a clientto aWLC using 702AP (Local Mode)with L2 Security -WEP using 2500

WLJ80S_702AP_02

PassedTo verify whetherclient getsconnected or not toa WLC using 702APwith L2 Security-WPA2+PSK using2500

Associating a clientto aWLC using 702AP (Local Mode)with L2 Security -WPA+WPA2-PSKusing 2500

WLJ80S_702AP_03

PassedTo verify whetherclient getsconnected or not toa WLC using 702APwith L2 Security- 802.1x using 2500

Associating a clientto aWLC using 702AP (Local Mode)with L2 Security-802.1x using 2500

WLJ80S_702AP_04


Associating a clientto aWLC using 702AP (FlexconnectMode) with L2Security - WEPusing 2500

WLJ80S_702AP_05


86

New Features - Test Summary702 AP


Associating a clientto aWLC using 702AP (FlexconnectMode) with L2Security -WPA+WPA2-PSKusing 2500

WLJ80S_702AP_06


Associating a clientto aWLC using 702AP (FlexconnectMode) with L2Security - 802.1xusing 2500

WLJ80S_702AP_07

PassedTo verify whether702 AP acts asAAA server or notfor LEAP clients byenabling LocalAuthenticationcheck box andLEAP check box ina Flex group.

Adding 702 AP inFlexconnect groupand making it asAAA server forLEAP clients.

WLJ80S_702AP_08

PassedTo verify whether702 AP acts asAAA server or notfor PEAP clients byenabling LocalAuthenticationcheck box andLEAP check box ina Flex group.

Adding 702 AP inFlexconnect groupand making it asAAA server forPEAP clients.

WLJ80S_702AP_09

PassedTo verify whetherthe client associatedto flexconnect APwill get reassociatedin case of faulttolerance

HREAP faulttolerance betweenconnected andstandalone AP-2.4GHz

WLJ80S_702AP_10


HREAP faulttolerance betweenstandalone andconnected AP-2.4GHz

WLJ80S_702AP_11


87




WLJ80S_702AP_12



WLJ80S_702AP_13

PassedTo verify client'sinitial association toa wlan with 11renabled with ft-pskAKM Suite inflexconnect centralswitching.

11r ClientAssociation withAKM PSK -FlexConnectCentralSwitch

WLJ80S_702AP_14

PassedVerify client's initialassociation to awlan with 11renabled with ft-pskAKM Suite inflexconnect localswitch central auth.

11r ClientAssociation withAKM PSK -FlexConnect LocalSwitch Central Auth

WLJ80S_702AP_15

PassedTo verify whetherthe Clientauthentication isdone via PrimaryRADIUS serverconfigured inflexconnect group

Client associationthrough PrimaryRADIUSserver(ISE) at sitelevel with L2SecurityWPA2+Dot1x(PEAP)

WLJ80S_702AP_16

PassedTo verify whetherthe Clientauthentication isdone via SecondaryRADIUS serverconfigured inflexconnect group

Client associationthrough SecondaryRADIUSserver(ISE)at sitelevel with L2SecurityWPA2+Dot1x(PEAP)

WLJ80S_702AP_17


Client associationthrough PrimaryRADIUSserver(ACS) at sitelevel with L2SecurityWPA2+Dot1x(PEAP)

WLJ80S_702AP_18


88



Client associationthrough SecondaryRADIUSserver(ACS) at sitelevel with L2SecurityWPA+Dot1x(PEAP)

WLJ80S_702AP_19

PassedTo check whetherthe client isassociatedsuccessfullyor notinto the networkthrough Web-Authusing 2500

Associating client-L3 security"Web-Auth" using2500

WLJ80S_702AP_20

PassedChecking for theAuthentication ofthe clients whenconnected to an APusing WPA+WPA2security .

Authentication forthe association ofclients-WPA

WLJ80S_702AP_21

PassedChecking for theAuthentication ofthe clients whenconnected to an APusing 802.1Xsecurity.

Authentication forthe association ofclients-802.1X

WLJ80S_702AP_22

PassedChecking for theAuthentication ofthe clients whenconnected to an APusing Static WEPsecurity.

Authentication forthe association ofclients-Static WEP

WLJ80S_702AP_23

PassedChecking for theAuthentication ofthe clients whenconnected to an APusing StaticWEP+802.1Xsecurity.

Authentication forthe association ofclients- StaticWEP+802.1X

WLJ80S_702AP_24

PassedTo check whetherregistered client issuccessfullyauthenticated andassociated withWLANS enabledMAC Filtering

Performing MACFiltering withClients registered inACS server-WiSM2 Controller

WLJ80S_702AP_25


89



Performing MACFiltering withClients registered inACS server- 2500Controller

WLJ80S_702AP_26



WLJ80S_702AP_27

PassedApply an AVCprofile with a rule toblock an applicationand check if thatapplication isdropped when triedto open andnotification is sendvia snmp trap

Verify AVC rule todrop an applicationworks fine

WLJ80S_702AP_28

PassedTo verify that aftercreating a new AVCprofile works, itworks fine in APSSO using 5508

AVC profile shouldwork fine in APSSO

WLJ80S_702AP_29

PassedTo verify theApplication trafficflow from client toAP when AP is inlocal mode andcentrally switchedflexconnect usingthe 5508, 7500 and2500 controllers

application trafficflow from client toAP when AP inlocal mode andcentrally switchedflexconnect -5508,7500 &2500WLC

WLJ80S_702AP_30

PassedTo verify if customDSCP value isconfigured andapplied successfullyfor a AVC rule

Configuring andverifying customDSCP value forAVC

WLJ80S_702AP_31


90


PassedTo Verify ifbandwidth contractapplied per-SSID ondownstream trafficworks fine using a2500 controller

Bandwidth contractRate limit appliedper-SSID ondownstream trafficin 2500

WLJ80S_702AP_32

PassedTo verify ifOverride Per-userbandwidth contracton downstream andupstream trafficworks fine

Override Per-userbandwidth contracton downstream andupstream traffic

WLJ80S_702AP_33

PassedChecking for theAuthentication ofthe client whenconnected to aWLAN in whichStatic WEP andWeb-Auth isenabled.

Authentication ofclient with SecurityStatic WEP andWeb-Auth -2500,5508, WiSM2 and7500 Controller.

WLJ80S_702AP_34

PassedChecking for theAuthentication ofthe clients whenconnected to aWLAN in whichStatic WEP+Dot1xand Web-Auth isenabled.

Authentication ofclient - Win 7 withSecurity StaticWEP+Dot1x andWeb-Auth usingISE-2500, 5508,WiSM2 and 7500Controller.

WLJ80S_702AP_35

PassedChecking for theAuthentication ofthe clients whenconnected to aWLAN in whichDot1x andWeb-Auth isenabled.

Authentication ofclients - Win 7 withSecurity Dot1xusing ISE andWeb-Auth-2500,5508, WiSM2 and7500 Controller.

WLJ80S_702AP_36

PassedTo configure theradio interface andto check and Verifythe clientassociation withopen security

Client Associationwith no security

WLJ80S_702AP_37

PassedTo check and verifythe clientassociation with theSecurity type asWEP

Client Associationwith WEP

WLJ80S_702AP_38


91


PassedTo check and verifyclient associationwith the Securitytype as WPA

Client Associationwith WPA

WLJ80S_702AP_39

PassedTo Check and verifyWGB associationwith root AP

Verify WGBassociation

WLJ80S_702AP_40

PassedTo check and verifytheAutonomousAPmanagement accessby http and telnet


WLJ80S_702AP_41

PassedTo check and verifythe Traffic flowbetween twowireless clients

Traffic flowbetween twowireless clients

WLJ80S_702AP_42

PassedTo verify theconnected client inAP managementpage


WLJ80S_702AP_43

PassedTo check and verifythe Trap Logs forconnected client


WLJ80S_702AP_44

PassedTo verify themanagement usercreation

Management userscreation

WLJ80S_702AP_45



WLJ80S_702AP_46

PassedTo check and verifyclient associationwith TKIP

Client Associationwith TKIP

WLJ80S_702AP_47

PassedTo check and verifyclient associationwith AES-CCMP

Client Associationwith AES-CCMP

WLJ80S_702AP_48

PassedTo check and verifyclient associationwith TKIP+WEP

Client Associationwith TKIP +WEP

WLJ80S_702AP_49

PassedTo check and verifyclient associationwith CKIP

Client Associationwith CKIP

WLJ80S_702AP_50

PassedTo check and verifyclient associationwith local radiusserver

Client Associationwith Local radiusserver

WLJ80S_702AP_51


92


PassedTo check and verifyTransmit andReceive antenna

Transmit andReceive antenna

WLJ80S_702AP_52

PassedVerify the clientassociation afterchanging the datarates

Data rates changeWLJ80S_702AP_53

PassedTo verify the CDPneighbor detailsusing show cdp

CDP neighbordetails

WLJ80S_702AP_54

PassedTo check and verifyclient associationwith no/opensecurity


WLJ80S_702AP_55

PassedTo check and verifyclient associationwith WEP


WLJ80S_702AP_56

PassedTo check and verifyclient associationwith WPA


WLJ80S_702AP_57

PassedTo check and verifyWGB associationwith root AP

WGB ModeWLJ80S_702AP_58



WLJ80S_702AP_59



WLJ80S_702AP_60

PassedTo verify themonitoring optionof connected clientin AP managementpage


WLJ80S_702AP_61



WLJ80S_702AP_62


93


PassedTo Configure fewchannels on GlobalDCA list. Try toconfigure a channelon RF profile DCAlist which is not partof Global list via theGUI. Verify GUIthrows error


WLJ80S_702AP_63

PassedTo Configure fewchannels on GlobalDCA list. Try toconfigure a channelon RF profile DCAlist which is not partof Global list via theCLI. Verify CLIthrows error


WLJ80S_702AP_64

PassedTo Verify the CLI -"show rf-profiledetails<RF-Profile>",shows parametersconfigured for DCAand Threshold fortraps.


WLJ80S_702AP_65

PassedTo Verify Config issuccessfullyuploaded and CW isseen as 20 MHz.Change the channelwidth to 40 Mhz onthe uploaded config.Download thechanged config andverify CW on RFprofile is set to 40MHz

Upload/Downloadof the Config andcheck for Channelwidth parameter onDCA RF profile

WLJ80S_702AP_66

PassedTo Configurevarious RF profileDCAparameters viathe CLI and verifyconfigs aresuccessful


WLJ80S_702AP_67


94


PassedVerify Config issuccessfullyuploaded and AvoidForeign APinterference is seenas enabled.


WLJ80S_702AP_68

PassedTo Verify config issuccessfullyuploaded. Changefew threshold valueson uploaded config.Download theconfig and verifythe changed values


WLJ80S_702AP_69

PassedTo Configurevarious thresholdfor traps via theGUI and verifyconfigs aresuccessful


WLJ80S_702AP_70



WLJ80S_702AP_71

PassedTo verify Configurevarious RF profileDCAparameters viathe GUI and verifyconfigs aresuccessful


WLJ80S_702AP_72

PassedTo verify Configurevarious thresholdfor traps via the CLIand verify configsare successful


WLJ80S_702AP_73

PassedTo verify Configurevarious thresholdfor traps via theGUI and verifyconfigs aresuccessful


WLJ80S_702AP_74


95


PassedConfigure DCA andthreshold for trapson RF profile. Resetthe Controller andverify the configsare retained


WLJ80S_702AP_75



WLJ80S_702AP_76



WLJ80S_702AP_77



WLJ80S_702AP_78

PassedTo verify whether702 AP is joined ornot with WiSM2Controller

Joining 702 AP toWiSM2 Controller

WLJ80S_702AP_79



WLJ80S_702AP_80



WLJ80S_702AP_81



WLJ80S_702AP_82


96


PassedTo verify whetherclient getsconnected or not toa WLC using 702APwith L2 Security- WEP usingWISM2

Associating a clientto aWLC using 702AP (Local Mode)with L2 Security -WEP usingWISM2

WLJ80S_702AP_83



WLJ80S_702AP_84



WLJ80S_702AP_85



WLJ80S_702AP_86

PassedTo verify whetherclient getsconnected or not toa WLC using 702APwith L2 Security-WPA2+PSK usingWISM2

Associating a clientto aWLC using 702AP (Local Mode)with L2 Security -WPA+WPA2-PSKusing WISM2

WLJ80S_702AP_87



WLJ80S_702AP_88



WLJ80S_702AP_89


97




WLJ80S_702AP_90

PassedTo verify whetherclient getsconnected or not toa WLC using 702APwith L2 Security- 802.1x usingWISM2

Associating a clientto aWLC using 702AP (Local Mode)with L2 Security-802.1x usingWISM2

WLJ80S_702AP_91



WLJ80S_702AP_92



WLJ80S_702AP_93



WLJ80S_702AP_94


Associating a clientto aWLC using 702AP (FlexconnectMode) with L2Security - WEPusing WISM2

WLJ80S_702AP_95



WLJ80S_702AP_96


98




WLJ80S_702AP_97



WLJ80S_702AP_98


Associating a clientto aWLC using 702AP (FlexconnectMode) with L2Security -WPA+WPA2-PSKusing WISM2

WLJ80S_702AP_99



WLJ80S_702AP_100



WLJ80S_702AP_101



WLJ80S_702AP_102


Associating a clientto aWLC using 702AP (FlexconnectMode) with L2Security - 802.1xusing WISM2

WLJ80S_702AP_103


99


PassedTo check whetherthe client isassociatedsuccessfully or notinto the networkthrough Web-Authusing 5500


WLJ80S_702AP_104



WLJ80S_702AP_105



WLJ80S_702AP_106

PassedTo check whetherthe client isassociatedsuccessfully or notinto the networkthrough Web-Authusing WISM2

Associating client-L3 security"Web-Auth" usingWISM2

WLJ80S_702AP_107

PassedTo verify AVC ruleto drop anapplication worksfine in 2500

Apply an AVCprofile with a rule toblock an applicationand check if thatapplication isdropped when triedto open using 2500

WLJ80S_702AP_108



WLJ80S_702AP_109


100




WLJ80S_702AP_110



WLJ80S_702AP_111

PassedTo verify AVC ruleto drop anapplication worksfine in WISM2

Apply an AVCprofile with a rule toblock an applicationand check if thatapplication isdropped when triedto open usingWISM2

WLJ80S_702AP_112

PassedTo verify AVC ruleto mark anapplication worksfine in WISM2

Apply an AVCprofile with a rule tomark an applicationand check if thatapplication ismarked when triedto open usingWISM2

WLJ80S_702AP_113

PassedTo verify AVC ruleto mark anapplication worksfine in 2500

Apply an AVCprofile with a rule tomark an applicationand check if thatapplication ismarked when triedto open using 2500

WLJ80S_702AP_114



WLJ80S_702AP_115


101




WLJ80S_702AP_116



WLJ80S_702AP_117

PassedTo Verify ifbandwidth contractapplied per-SSID ondownstream trafficworks fine


WLJ80S_702AP_118



WLJ80S_702AP_119



WLJ80S_702AP_120

2700 APDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether2700AP is joined ornot with 2500Controller.


WLJ80S_2700AP_01


Associating a clientto a WLC using2700 AP (LocalMode) with L2Security - WEPusing 2500

WLJ80S_2700AP_02


102



Associating a clientto a WLC using2700 AP (LocalMode) with L2Security -WPA+WPA2-PSKusing 2500

WLJ80S_2700AP_03


Associating a clientto a WLC using2700 AP (LocalMode) with L2Security -802.1xusing 2500

WLJ80S_2700AP_04


Associating a clientto a WLC using2700 AP(FlexconnectMode)with L2 Security -WEP using 2500

WLJ80S_2700AP_05


Associating a clientto a WLC using2700 AP(FlexconnectMode)with L2 Security -WPA+WPA2-PSKusing 2500

WLJ80S_2700AP_06


Associating a clientto a WLC using2700 AP(FlexconnectMode)with L2 Security -802.1x using 2500

WLJ80S_2700AP_07

PassedTo verify whether2700 AP acts asAAA server or notfor LEAP clients byenabling LocalAuthenticationcheck box andLEAP check box ina Flex group.

Adding 2700 AP inFlexconnect groupand making it asAAA server forLEAP clients.

WLJ80S_2700AP_08


103


PassedTo verify whether2700 AP acts asAAA server or notfor PEAP clients byenabling LocalAuthenticationcheck box andLEAP check box ina Flex group.

Adding 2700 AP inFlexconnect groupand making it asAAA server forPEAP clients.

WLJ80S_2700AP_09



WLJ80S_2700AP_10



WLJ80S_2700AP_11



WLJ80S_2700AP_12



WLJ80S_2700AP_13

PassedTo verify client'sinitial association toa wlan with 11renabled with ft-pskAKM Suite inflexconnect centralswitching.

11r ClientAssociation withAKM PSK -FlexConnectCentralSwitch

WLJ80S_2700AP_14

PassedVerify client's initialassociation to awlan with 11renabled with ft-pskAKM Suite inflexconnect localswitch central auth.

11r ClientAssociation withAKM PSK -FlexConnect LocalSwitch Central Auth

WLJ80S_2700AP_15


104



Client associationthrough PrimaryRADIUSserver(ISE) at sitelevel with L2SecurityWPA2+Dot1x(PEAP)

WLJ80S_2700AP_16


Client associationthrough SecondaryRADIUSserver(ISE)at sitelevel with L2SecurityWPA2+Dot1x(PEAP)

WLJ80S_2700AP_17


Client associationthrough PrimaryRADIUSserver(ACS) at sitelevel with L2SecurityWPA2+Dot1x(PEAP)

WLJ80S_2700AP_18


Client associationthrough SecondaryRADIUSserver(ACS) at sitelevel with L2SecurityWPA+Dot1x(PEAP)

WLJ80S_2700AP_19

PassedTo check whetherthe client isassociatedsuccessfullyor notinto the networkthrough Web-Authusing 2500


WLJ80S_2700AP_20

PassedChecking for theAuthentication ofthe clients whenconnected to an APusing WPA+WPA2security .


WLJ80S_2700AP_21

PassedChecking for theAuthentication ofthe clients whenconnected to an APusing 802.1Xsecurity.


WLJ80S_2700AP_22


105


PassedChecking for theAuthentication ofthe clients whenconnected to an APusing Static WEPsecurity.


WLJ80S_2700AP_23

PassedChecking for theAuthentication ofthe clients whenconnected to an APusing StaticWEP+802.1Xsecurity.


WLJ80S_2700AP_24


Performing MACFiltering withClients registered inACS server-WiSM2 Controller

WLJ80S_2700AP_25



WLJ80S_2700AP_26



WLJ80S_2700AP_27

PassedApply an AVCprofile with a rule toblock an applicationand check if thatapplication isdropped when triedto open andnotification is sendvia snmp trap

Verify AVC rule todrop an applicationworks fine

WLJ80S_2700AP_28


106


PassedTo verify that aftercreating a new AVCprofile works, itworks fine in APSSO using 5508


WLJ80S_2700AP_29

PassedTo verify theApplication trafficflow from client toAP when AP is inlocal mode andcentrally switchedflexconnect usingthe 5508, 7500 and2500 controllers


WLJ80S_2700AP_30

PassedTo verify if customDSCP value isconfigured andapplied successfullyfor a AVC rule


WLJ80S_2700AP_31

PassedTo Verify ifbandwidth contractapplied per-SSID ondownstream trafficworks fine using a2500 controller


WLJ80S_2700AP_32

PassedTo verify ifOverride Per-userbandwidth contracton downstream andupstream trafficworks fine


WLJ80S_2700AP_33

PassedChecking for theAuthentication ofthe client whenconnected to aWLAN in whichStatic WEP andWeb-Auth isenabled.

Authentication ofclient with SecurityStatic WEP andWeb-Auth-2500,5508,WiSM2and 7500Controller.

WLJ80S_2700AP_34

PassedChecking for theAuthentication ofthe clients whenconnected to aWLAN in whichStatic WEP+Dot1xand Web-Auth isenabled.

Authentication ofclient - Win 7 withSecurity StaticWEP+Dot1x andWeb-Auth usingISE-2500, 5508,WiSM2 and 7500Controller.

WLJ80S_2700AP_35


107


PassedChecking for theAuthentication ofthe clients whenconnected to aWLAN in whichDot1x andWeb-Auth isenabled.

Authentication ofclient - Win 7 withSecurity Dot1xusing ISE andWeb-Auth -2500,5508, WiSM2 and7500 Controller.

WLJ80S_2700AP_36

PassedTo configure theradio interface andto check and Verifythe clientassociation withopen security


WLJ80S_2700AP_37

PassedTo check and verifythe clientassociation with theSecurity type asWEP


WLJ80S_2700AP_38

PassedTo check and verifyclient associationwith the Securitytype as WPA


WLJ80S_2700AP_39

PassedTo Check and verifyWGB associationwith root AP

Verify WGBassociation

WLJ80S_2700AP_40



WLJ80S_2700AP_41



WLJ80S_2700AP_42

PassedTo verify theconnected client inAP managementpage


WLJ80S_2700AP_43



WLJ80S_2700AP_44

PassedTo verify themanagement usercreation

Management usersWLJ80S_2700AP_45


108




WLJ80S_2700AP_46

PassedTo check and verifyclient associationwith TKIP

Client Associationwith TKIP

WLJ80S_2700AP_47

PassedTo check and verifyclient associationwith AES-CCMP

Client Associationwith AES-CCMP

WLJ80S_2700AP_48

PassedTo check and verifyclient associationwith TKIP+WEP

Client Associationwith TKIP +WEP

WLJ80S_2700AP_49

PassedTo check and verifyclient associationwith CKIP

Client Associationwith CKIP

WLJ80S_2700AP_50

PassedTo check and verifyclient associationwith local radiusserver

Client Associationwith Local radiusserver

WLJ80S_2700AP_51

PassedTo check and verifyTransmit andReceive antenna

Transmit andReceive antenna

WLJ80S_2700AP_52

PassedVerify the clientassociation afterchanging the datarates

Data rates changeWLJ80S_2700AP_53

PassedTo verify the CDPneighbor detailsusing show cdp

CDP neighbordetails

WLJ80S_2700AP_54

PassedTo check and verifyclient associationwith no/opensecurity


WLJ80S_2700AP_55

PassedTo check and verifyclient associationwith WEP


WLJ80S_2700AP_56

PassedTo check and verifyclient associationwith WPA


WLJ80S_2700AP_57

PassedTo check and verifyWGB associationwith root AP

WGB ModeWLJ80S_2700AP_58


109




WLJ80S_2700AP_59



WLJ80S_2700AP_60

PassedTo verify themonitoring optionof connected clientin AP managementpage


WLJ80S_2700AP_61



WLJ80S_2700AP_62

PassedTo Configure fewchannels on GlobalDCA list. Try toconfigure a channelon RF profile DCAlist which is not partof Global list via theGUI. Verify GUIthrows error


WLJ80S_2700AP_63

PassedTo Configure fewchannels on GlobalDCA list. Try toconfigure a channelon RF profile DCAlist which is not partof Global list via theCLI. Verify CLIthrows error


WLJ80S_2700AP_64

PassedTo Verify the CLI -"show rf-profiledetails<RF-Profile>",shows parametersconfigured for DCAand Threshold fortraps.


WLJ80S_2700AP_65


110


PassedTo Verify Config issuccessfullyuploaded and CW isseen as 20 MHz.Change the channelwidth to 40 Mhz onthe uploaded config.Download thechanged config andverify CW on RFprofile is set to 40MHz

Upload/Downloadof the Config andcheck for Channelwidth parameter onDCA RF profile

WLJ80S_2700AP_66



WLJ80S_2700AP_67

PassedVerify Config issuccessfullyuploaded and AvoidForeign APinterference is seenas enabled.


WLJ80S_2700AP_68

PassedTo Verify config issuccessfullyuploaded. Changefew threshold valueson uploaded config.Download theconfig and verifythe changed values


WLJ80S_2700AP_69

PassedTo Configurevarious thresholdfor traps via theGUI and verifyconfigs aresuccessful


WLJ80S_2700AP_70



WLJ80S_2700AP_71


111


PassedTo verify Configurevarious RF profileDCAparameters viathe GUI and verifyconfigs aresuccessful


WLJ80S_2700AP_72

PassedTo verify Configurevarious thresholdfor traps via the CLIand verify configsare successful


WLJ80S_2700AP_73

PassedTo verify Configurevarious thresholdfor traps via theGUI and verifyconfigs aresuccessful


WLJ80S_2700AP_74

PassedConfigure DCA andthreshold for trapson RF profile. Resetthe Controller andverify the configsare retained


WLJ80S_2700AP_75

PassedTo verify whether2700AP is joined ornot with 5500Controller


WLJ80S_2700AP_76



WLJ80S_2700AP_77



WLJ80S_2700AP_78

PassedTo verify whether2700AP is joined ornot with WiSM2Controller

Joining 2700 AP toWiSM2 Controller

WLJ80S_2700AP_79



WLJ80S_2700AP_80


112




WLJ80S_2700AP_81



WLJ80S_2700AP_82


Associating a clientto a WLC using2700 AP (LocalMode) with L2Security - WEPusing WISM2

WLJ80S_2700AP_83



WLJ80S_2700AP_84



WLJ80S_2700AP_85



WLJ80S_2700AP_86


Associating a clientto a WLC using2700 AP (LocalMode) with L2Security -WPA+WPA2-PSKusing WISM2

WLJ80S_2700AP_87


113




WLJ80S_2700AP_88



WLJ80S_2700AP_89



WLJ80S_2700AP_90


Associating a clientto a WLC using2700 AP (LocalMode) with L2Security -802.1xusing WISM2

WLJ80S_2700AP_91



WLJ80S_2700AP_92



WLJ80S_2700AP_93



WLJ80S_2700AP_94


114



Associating a clientto a WLC using2700 AP(FlexconnectMode)with L2 Security -WEP usingWISM2

WLJ80S_2700AP_95



WLJ80S_2700AP_96



WLJ80S_2700AP_97



WLJ80S_2700AP_98


Associating a clientto a WLC using2700 AP(FlexconnectMode)with L2 Security -WPA+WPA2-PSKusing WISM2

WLJ80S_2700AP_99



WLJ80S_2700AP_100



WLJ80S_2700AP_101


115




WLJ80S_2700AP_102


Associating a clientto a WLC using2700 AP(FlexconnectMode)with L2 Security -802.1x usingWISM2

WLJ80S_2700AP_103



WLJ80S_2700AP_104



WLJ80S_2700AP_105



WLJ80S_2700AP_106

PassedTo check whetherthe client isassociatedsuccessfully or notinto the networkthrough Web-Authusing WISM2

Associating client-L3 security"Web-Auth" usingWISM2

WLJ80S_2700AP_107


116




WLJ80S_2700AP_108



WLJ80S_2700AP_109



WLJ80S_2700AP_110



WLJ80S_2700AP_111

PassedTo verify AVC ruleto drop anapplication worksfine in WISM2

Apply an AVCprofile with a rule toblock an applicationand check if thatapplication isdropped when triedto open usingWISM2

WLJ80S_2700AP_112

PassedTo verify AVC ruleto mark anapplication worksfine in WISM2

Apply an AVCprofile with a rule tomark an applicationand check if thatapplication ismarked when triedto open usingWISM2

WLJ80S_2700AP_113


117




WLJ80S_2700AP_114



WLJ80S_2700AP_115



WLJ80S_2700AP_116



WLJ80S_2700AP_117



WLJ80S_2700AP_118



WLJ80S_2700AP_119



WLJ80S_2700AP_120


118


C H A P T E R 4Regression Features - Test Summary

• WLC AireOS, page 119

• PI, page 135

• MSE, page 137

• SR Test Cases, page 137

• Fix Verification, page 142

• TAC, page 147

• SR/CFD, page 230

• NEC, page 266

• Adhoc Test Cases, page 270

• Related Documentation, page 274

WLC AireOS

Re-instating PPPoE ModulesDefectsStatusDescriptionTitleLogical ID

PassedTo check whether PPPoEsubmode is enabled or not inAP3702 and checkwhether APgets associated or not to WLC7500 with submode as PPPoE

Enabling submodePPPoE in AP3702and associating it toWLC 7500.

WLJ80S_PPPoE_01

PassedTo check whether PPPoEsubmode is enabled or not inAP1532 and checkwhether APgets associated or not to WLC7500 with submode as PPPoE

Enabling submodePPPoE in AP1532and associating it toWLC 7500.

WLJ80S_PPPoE_02


119


PassedTo check whether PPPoEsubmode is enabled or not inAP702I and check whether APgets associated or not to WLC7500 with submode as PPPoE

Enabling submodePPPoE in AP702Iand associating it toWLC 7500.

WLJ80S_PPPoE_03

PassedTo check whether Win 7 clientable to get associatedsuccessfully or not to AP 3702with L2 SecurityMac Filtering.

Associating Win 7client to AP3702(SubmodePPPoE) with L2security MacFiltering in WLC7500

WLJ80S_PPPoE_04

PassedTo check whether Mac Bookclient able to get associatedsuccessfully or not to AP 702with L2 SecurityMac Filtering.

AssociatingMacBook client toAP 702(SubmodePPPoE) with L2security MacFiltering in WLC7500

WLJ80S_PPPoE_05

PassedTo check whether Samsung S4andIphone clients able to getassociated successfully or notto AP 3702 with L2 SecurityMac Filtering.

AssociatingSamsung S4 andIphone clients to AP3702(SubmodePPPoE) with L2security MacFiltering in WLC7500

WLJ80S_PPPoE_06

PassedTo check whether Win 7 clientable to get associatedsuccessfully or not to AP 1532with L2 Security Dot1x.

Associating Win 7client to AP1532(SubmodePPPoE) with L2security Dot1x inWLC 7500

WLJ80S_PPPoE_07

PassedTo check whether Mac Bookclient able to get associatedsuccessfully or not to AP 3702with L2 Security Dot1x.

AssociatingMacBook client toAP 3702(SubmodePPPoE) with L2security Dot1x inWLC 7500

WLJ80S_PPPoE_08


120

Regression Features - Test SummaryRe-instating PPPoE Modules


PassedTo check whether Samsung S4and Iphone clients able to getassociated successfully or notto AP 702 with L2 SecurityDot1x.

AssociatingSamsung S4 andIphone clients to AP702(SubmodePPPoE) with L2security Dot1x inWLC 7500

WLJ80S_PPPoE_09

PassedTo check whether 3702 APgetting Fallback or not toSecondaryWLCwhen PrimaryWLC is down.

Performing3702AP(SubmodePPPoE) Fallbackfrom Primary toSecondary WLC

WLJ80S_PPPoE_10



WLJ80S_PPPoE_11



WLJ80S_PPPoE_12

PassedTo check whether 3702 APgetting Fallback or not toSecondaryWLCwhen PrimaryWLC is down and also checkwhether clients(Win 7 andMacBook) able to access thenetwork in Secondary WLC.

Performing3702AP(SubmodePPPoE) Fallbackfrom Primary toSecondary WLCwith association ofclients(Win 7 andMacBook).

WLJ80S_PPPoE_13

PassedTo check whether 702 APgetting Fallback or not toSecondaryWLCwhen PrimaryWLC is down and also checkwhether clients(Samsung S4and Iphone) and MacBook)able to access the network inSecondary WLC.

Performing702AP(SubmodePPPoE) Fallbackfrom Primary toSecondary WLCwith association ofclients(Samsung S4and Iphone).

WLJ80S_PPPoE_14

PassedTo verify whether 3702 AP actsas AAA server or not for LEAPclients by enabling LocalAuthentication check box andLEAP check box in a Flexgroup.

Adding 3702AP(submode asPPPoE) inFlexconnect groupand making it asAAA server forLEAP clients.

WLJ80S_PPPoE_15


121

Regression Features - Test SummaryRe-instating PPPoE Modules


PassedTo verify whether 1532AP(submode as PPPoE) acts asAAA server or not for PEAPclients by enabling LocalAuthentication check box andLEAP check box in a Flexgroup.

Adding 1532AP(submode asPPPoE) inFlexconnect groupand making it asAAA server forPEAP clients.

WLJ80S_PPPoE_16

PassedTo verify whether roamingoccurs seamlessly or notbetween AP's within a Flexgroup.

Adding 2 702 AP'sin Flex group andperforming roamingbetween AP's withLEAP clients.

WLJ80S_PPPoE_17

PassedTo verify whether roamingoccurs seamlessly or notbetween AP's within a Flexgroup.

Adding 2 1532 AP'sin Flex group andperforming roamingbetween AP's withPEAP clients.

WLJ80S_PPPoE_18

PassedTo check whether clients ableto get associated successfullyor not to AP 1532 with L3Security Web-Auth.

Associating clientsto AP1532(SubmodePPPoE) with L3securityWeb-Authenticationin WLC 7500

WLJ80S_PPPoE_19

PassedTo check whether clients ableto get associated successfullyor not to AP 702 with L3Security Web-Auth.

Associating clientstoAP 702(SubmodePPPoE) with L3securityWeb-Authenticationin WLC 5500

WLJ80S_PPPoE_20

L2 SecurityDefectsStatusDescriptionTitleLogical ID

PassedTo check whether the 7921GIP phone is associatedsuccessfully into the networkthroughWEP authenticationmethod

Associating 7921GIP phone - WEP

WLJ80S_SR_L2_09


122

Regression Features - Test SummaryL2 Security


PassedTo check whether the 7921GIP phone is associatedsuccessfully into the networkthroughWPA authenticationmethod

Associating 7921GIP phone - WPA

WLJ80S_SR_L2_10

PassedTo verify the 7921G IPPhone is successfullyauthenticated and associatedthrough WEP

7921G IP PhoneAssociation throughWEP(RADIUSServerAuthentication)

WLJ80S_SR_L2_11

PassedChecking for theAuthentication of the clientswhen connected to an AP.


WLJ80S_SR_L2_12



WLJ80S_SR_L2_13



WLJ80S_SR_L2_14



WLJ80S_SR_L2_15

L3 SecurityDefectsStatusDescriptionTitleLogical ID

PassedTo check theCustomized(Downloaded)web-auth configuration inNCS reflects in WLC.

ConfiguringCustomized(Downloaded)web-auth using NCS

WLJ80S_SR_L3_01

PassedTo verify the successfulcustomized web loginpage with InternalAuthentication.

CT2500: Customized(Downloaded) loginpage for the controller.

WLJ80S_SR_L3_02

PassedTo verify the customizedweb login page bundle isdownloaded successfully.

CT2500: Downloadcustomized login pagefor the controller.

WLJ80S_SR_L3_03


123

Regression Features - Test SummaryL3 Security


PassedTo verify the successfulcustomized web loginpage with internalauthentication

Customized web authlogin page for thecontroller-Laptop

WLJ80S_SR_L3_04

PassedTo verify the successfuldownload of customizedlogin page

Downloading thecustomized login page

WLJ80S_SR_L3_05

PassedTo verify the successfulcustomized web loginpage with internalauthentication

Customized web loginpage for the controller

WLJ80S_SR_L3_06

PassedTo verify the successfuldefault web login pagewith InternalAuthentication.

CT2500: Default loginpage for the controller.

WLJ80S_SR_L3_07

PassedTo verify the successfuldefault web login pagewith Internalauthentication

Default web login pagefor the controller

WLJ80S_SR_L3_08

Link Aggregation ModeDefectsStatusDescriptionTitleLogical ID

PassedTo verify the LightWeight Access PointRegistration/Join status oncontroller - Local Mode

Enable LinkAggregation on thecontroller- LAPLocal Mode

WLJ80S_LAG_19

PassedTo verify the LightWeight Access PointRegistration status oncontroller - Flex ConnectMode

Enable LinkAggregation on thecontroller -LAP FlexConnect Mode

WLJ80S_LAG_20

PassedTo verify the successfulassociation of wirelessclient with Light WeightAccess Point

Client Associationwith Light WeightAccess Point afterLink Aggregationfailover

WLJ80S_LAG_21

PassedTo verify the successfulPING, FTP packetsduring LAG failover

LAG failover -Ping,FTP (Refer-CSCth12513)

WLJ80S_LAG_22


124

Regression Features - Test SummaryLink Aggregation Mode


PassedTo verify the successfulLAG port status messagein SNMP manager

LAGPort status TrapLog with SNMPManager (Refer:CSCto58101 Delayin Port Up downcauses issues withLAG working onWLC

WLJ80S_LAG_23

PassedTo check active controllerports status in LinkAggregation failover

Active controllerports status when itis in LinkAggregation (LAG)failover

WLJ80S_LAG_24

High AvailabilityDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether the HApair(ACTIVE:STANDBY) isup successfully

Bringing HA pairup- WLC 5508

WLJ80S_SR_HA_25

PassedTo verify whether the HApair(ACTIVE:STANDBY) isup successfully


WLJ80S_SR_HA_26

PassedTo verify the role negotiationbetween the controllers withdifferent hardware models

Controller HA pairwith differenthardware models

WLJ80S_SR_HA_27

PassedTo verify the role negotiationbetween the controllers withdifferent software versions

Controller HA pairwith differentsoftware versions

WLJ80S_SR_HA_28

PassedTo verify the HA paircontroller modes afterdisconnecting the redundancyport

Controller modewhen theredundancy portloses connectivity

WLJ80S_SR_HA_29

PassedTo verify the HA paircontroller modes when theGateway is not reachable fromthe STANDBY controller

Controller modewhen the Gatewayis not reachable tothe STANDBYcontroller

WLJ80S_SR_HA_30


125

Regression Features - Test SummaryHigh Availability


PassedTo verify the HA paircontroller modes when theGateway is not reachable fromthe ACTIVE controller

Controller modewhen the Gatewayis not reachable tothe ACTIVEcontroller

WLJ80S_SR_HA_31

PassedTo verify the HA paircontroller modes when theGateway is not reachable toboth the controllers

Controller modewhen the Gatewayis not reachable toboth the controller

WLJ80S_SR_HA_32

PassedTo verify the controller modesafter power failure on both thecontrollers

Controllermodes(HA pair)after power failure

WLJ80S_SR_HA_33

PassedTo verify the HA mode afterresetting the peer system fromACTIVE controller

HA mode afterresetting the peersystem fromACTIVE

WLJ80S_SR_HA_34

PassedTo check whether the Clientgets disassociated and forcedto re-join to the controller afterAP SSO

Client status duringAP SSO after activefailover-WebAuthentication

WLJ80S_SR_HA_35

RoamingDefectsStatusDescriptionTitleLogical ID

PassedTo verify client's initialassociation to a wlan with11r enabled with ft-PSKAKM Suite in flexconnectcentral switching.

11r Client Associationwith AKM PSK -FlexConnect CentralSwitch

WLJ80S_11r_36

PassedVerify client's initialassociation to a wlan with11r enabled with ft-PSKAKM Suite in flexconnectlocal switch central auth.

11r Client Associationwith AKM PSK -FlexConnect LocalSwitch Central Auth

WLJ80S_11r_37

PassedTo verify fast transitionclient roaming over the airwithin the same controllerin flexconnect central auth.

Over the AirIntra-controllerroaming - flexconnectCentral Switch

WLJ80S_11r_38


126

Regression Features - Test SummaryRoaming


PassedVerify fast transition clientroaming over the DSwithin the same controllerin flexconnect centralswitch.

Over the DSIntra-controllerroaming - FlexconnectCentral Switch VLANPooling

WLJ80S_11r_39

PassedVerify open security 11rOver-the-Air Roaming

Open SecurityOver-the-Air Roaming- controller

WLJ80S_11r_40

PassedVerify open security 11rOver-the-Air Roaming

Open SecurityOver-the-Air Roaming-NCS

WLJ80S_11r_41

PassedTo check for the successfuland seamless roaming ofwireless data clientsbetween APs of same Flexconnect group whencontroller is "Down".

Roaming of wirelessdata clients withinAPs of one Flexconnect group whencontroller is Down.

WLJ80S_11r_42

PassedTo check for the seamlessroaming from one AP toanother from the same FlexConnect group.

Roaming of dataclients betweenAPs insame Flex connectgroup.

WLJ80S_11r_44

AAADefectsStatusDescriptionTitleLogical ID

PassedTo verify the accesspoint configurationin PI GUI

Configure an accesspoint in PI

WLJ80S_aaa_01

PassedTo verify the accesspoint parameters(name,mode, adminstatus, etc) are ableto change when PIis integrated withACS server

Change the accesspoint parameters inPI

WLJ80S_aaa_02

PassedTo verify the accesspoint configurationin virtual PI GUI

Configure an accesspoint in virtual PI

WLJ80S_aaa_03


127

Regression Features - Test SummaryAAA

PassedTo verify the accesspoint parameters(name,mode, adminstatus, etc) are ableto change whenvirtual PI isintegratedwithACSserver

Change the accesspoint parameters invirtual PI

WLJ80S_aaa_04

Flexconnect EnhancementsDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether theWGB associates and theclients are registered tothe controller throughFlexconnect AP.

WGBAssociation,WGB clientregistrationthroughFlexconnect AP inconnected mode.

WLJ80S_FLEX_48

PassedTo verify whether theWGB associates and theclients are registered tothe controller throughFlexconnect AP instandalone mode.

WGBAssociation,WGB clientregistrationthroughFlexconnect AP instandalone mode

WLJ80S_FLEX_49

PassedTo verify whether theWGB associates with theflexconnect through localauthenticated WLAN

WGB Associationthrough LocalauthenticatedWLAN.

WLJ80S_FLEX_50

PassedTo verify whether theWGB disassociates fromthe controller upondeletion

WGBdisassociation fromthe controller

WLJ80S_FLEX_51

PassedTo verify whether theWGB disassociates fromthe controller upondeletion

WGB clientde-registrationwith theflexconnect instandalonemode toconnected mode

WLJ80S_FLEX_52


128

Regression Features - Test SummaryFlexconnect Enhancements


PassedTo verify whether WGBand WGB clientsre-associates to thecontroller afterflexconnect AP reloads

Flexconnect APreload in connectedmode when WGBisassociated-Centralauth locallyswitched

WLJ80S_FLEX_53

PassedTo verify whether WGBand WGB clientsre-associates to thecontroller afterflexconnect AP reloads

Flexconnect APreload instandalone modewhen WGB isassociated-Localauthentication

WLJ80S_FLEX_54

PassedTo verify the WGB clientre-associates successfullyto a different flexConnectafter roaming within thecontroller

WGB Clientsroaming to adifferentflexconnect on thesame controller

WLJ80S_FLEX_55

HREAPDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether theclient associated toflexconnect AP will getre-associated in case offault tolerance

HREAP fault tolerancebetween connected andstandalone AP-2.4GHz

WLJ80S_SR_Fault_56

PassedTo verify whether theclient associated toflexconnect AP will getre-associated in case offault tolerance

HREAP fault tolerancebetween standaloneand connected AP-2.4GHz

WLJ80S_SR_Fault_57


129

Regression Features - Test SummaryHREAP

Anyconnect VPNDefectsStatusDescriptionTitleLogical ID

PassedTo check whether theAnyconnect VPN isconnecting or not usingWPA+WPA2 layer2 securityin Win7 client

WPA+WPA2network(AnyConnect)in Win7 client

WLJ80S_Any_58

PassedTo check whether theAnyConnect VPN isconnecting or not, usingStatic WEP layer2 securityin Win7 client

Static WEPnetwork(AnyConnect)in Win7 client

WLJ80S_Any_59

PassedTo check whether theAnyConnect VPN is connector not using "None" Layer 2security in Win7 client

Layer 2 securityNone for open auth(AnyConnect) inWin7 client

WLJ80S_Any_60

PassedTo check whether theAnyconnect VPN is connector not, using WPA+WPA2layer2 security in MacBookclient

WPA+WPA2network(AnyConnect)using MacBookclient

WLJ80S_Any_61

PassedTo check whether theAnyconnect VPN is connector not using Static WEPlayer2 security in MacBookClient

Static WEPnetwork(AnyConnect) inMacBook Client

WLJ80S_Any_62

PassedTo check whether theAnyconnect VPN is connector not , using "None" Layer2 security inMacBookClient

Layer 2 security"None" for openauth network(AnyConnect) inMacBook Client

WLJ80S_Any_63

PassedTo check whether theAnyconnect VPN is connector not, using WPA+WPA2layer2 security in SamsungGalaxy sII client

WPA+WPA2network(AnyConnect)using SamsungGalaxy sII client

WLJ80S_Any_64

PassedTo check whether theAnyconnect VPN is connector not using Static WEPlayer2 security in SamsungGalaxy sII Client

Static WEPnetwork(AnyConnect) inSamsung GalaxysII client

WLJ80S_Any_65


130

Regression Features - Test SummaryAnyconnect VPN


PassedTo check whether theAnyconnect VPN is connector not , using "None" Layer2 security in SamsungGalaxy sII Client.

Layer 2 security"None" for openauth network(Anyconnect) inSamsung GalaxysII client.

WLJ80S_Any_66

Dot1x and Web-Auth SupportDefectsStatusDescriptionTitleLogical ID

PassedChecking for theAuthentication of theclient when connected toa WLAN in which StaticWEP and Web-Auth isenabled.

Authentication ofclient(Apple MacBook) with SecurityStatic WEP andWeb-Auth-2500,5508, WiSM2and 7500 Controller.

WLJ80S_SR_Web_67

PassedChecking for theAuthentication of theclients when connectedto a WLAN in whichStatic WEP+Dot1x andWeb-Auth is enabled.

Authentication ofclients(Apple MacBook andWin 7) withSecurity StaticWEP+Dot1x andWeb-Auth usingISE-2500,5508,WiSM2 and 7500Controller.

WLJ80S_SR_Web_68

PassedChecking for theAuthentication of theclients when connectedto a WLAN in whichDot1x and Web-Auth isenabled.

Authentication ofclients(Apple MacBook andWin 7) withSecurity Dot1x usingISE and WebAuth-2500 ,5508 ,WiSM2 and 7500Controller.

WLJ80S_SR_Web_69


131

Regression Features - Test SummaryDot1x and Web-Auth Support

Multiple RADIUS Server Per SSIDDefectsStatusDescriptionTitleLogical ID

PassedTo verify whetherDot1x authenticationcan be performedsuccessfully to theclients associated viathe Primary RADIUSserver over the PPPoEconnection with theVlan mapped

Performing Dot1xauthentication overPPPoE AP withRADIUS serversconfigured(Primary)-2500,5508,WiSM2and 7500 WLC

WLJ80S_Rad_70

PassedTo verify whetherDot1x authenticationcan be performedsuccessfully to theclients associated viathe secondaryRADIUS server overthe PPPoE connectionwith the Vlan mapped

Performing Dot1xauthentication overPPPoE AP withRADIUS serversconfigured(Secondary)-2500,5508,WiSM2and 7500 WLC

WLJ80S_Rad_71

PassedTo verify whetherDot1x authenticationcan be performedsuccessfully to theclients associated viathe secondaryRADIUS server overthe PPPoE connectionwith the Vlan mapped

Performing Dot1xauthentication overPPPoE AP withRADIUS serversconfigured(Primaryfailover)-2500,5508,WiSM2and 7500 WLC

WLJ80S_Rad_72

PassedTo verify whetherDot1x authenticationcan be performedsuccessfully to theclients associated viathe Primary RADIUSserver over the FlexAP connection withthe Vlan mapped

Performing Dot1xauthentication overFlexConnect APwithRADIUS serversconfigured(Primary)-2500,5508,WiSM2and 7500 WLC

WLJ80S_Rad_73


132

Regression Features - Test SummaryMultiple RADIUS Server Per SSID


PassedTo verify whetherDot1x authenticationcan be performedsuccessfully to theclients associated viathe secondaryRADIUS server overthe Flex APconnection with theVlan mapped

Performing Dot1xauthentication overFlexConnect APwithRADIUS serversconfigured(Secondary)-2500,5508,WiSM2and 7500 WLC

WLJ80S_Rad_74

PassedTo verify whetherDot1x authenticationcan be performedsuccessfully to theclients associated viathe secondaryRADIUS server overthe Flex APconnection with theVlan mapped

Performing Dot1xauthentication overFlexConnect APwithRADIUS serversconfigured(Primaryfailover)-2500,5508,WiSM2and 7500 WLC

WLJ80S_Rad_75

Secure FTPDefectsStatusDescriptionTitleLogical ID

PassedTo verify controller able todownload the image usingSFTP method and installsproperly

Transfer downloadof controller imagewith SFTPmethod- WLC5500series ,WiSM2 , 2500series

WLJ80S_SFTP__76

PassedTo verify controller able todownload a configurationand upload the currentconfiguration using SFTPtransfer method

Transfer ofcontrollerconfiguration withSFTP method -WLC 5500 , 2500, WiSM2.

WLJ80S_SFTP__77

PassedTo verify controller is ableto download all thesupported certificates usingSFTP transfer method

Transfer downloadof controllercertificates withSFTP method -WLC Virtual and7500

WLJ80S_SFTP__78


133

Regression Features - Test SummarySecure FTP


PassedVerify controller validatesproperly the transferparameters like server IPaddress, Port number,filename, and path. Transferis aborted if any of theabove configurationparameters are in-correct orserver issues - Allcontrollers

SFTP Transfervalidation withother configurationitems like, path,filename, server IPand port number -All Controllers

WLJ80S_SFTP__79

PassedTo verify controller is ableto upload all the othersupported data type filesusing SFTP transfermethod- WLC 5500 , 2500& WiSM2.

Transfer upload ofother data typefiles with SFTPmethod - WLC5500 series , 2500and WiSM2

WLJ80S_SFTP__80

NBARDefectsStatusDescriptionTitleLogical ID

PassedTo verify AVC rule to dropan application works fine

Apply an AVCprofile with a rule toblock an applicationand check if thatapplication isdropped when triedto open andnotification is sendvia SNMP trap

WLJ80S_NBAR_82

PassedTo verify if AVC profileworks fine after AP SSO


WLJ80S_NBAR_83

PassedTo verify the IP traffic flowfrom client to AP when APis in local mode andcentrally switchedflexconnect


WLJ80S_NBAR_84


134

Regression Features - Test SummaryNBAR


PassedTo verify if custom DSCPvalue is configured andapplied successfully for aAVC rule


WLJ80S_NBAR_85

PassedTo Verify if bandwidthcontract applied per-SSIDon downstream traffic worksfine

Bandwidth contractRate limit appliedper-SSID ondownstream traffic

WLJ80S_NBAR_86

PassedTo verify if OverridePer-user bandwidth contracton downstream andupstream traffic works fine


WLJ80S_NBAR_87

PassedTo verify the AVCmonitoring .

AVC MonitoringWLJ80S_NBAR_88

PI

NCS MapsDefectsStatusDescriptionTitleLogical ID

PassedTo verify the successful copyand replace

Copy and ReplaceAP-Map

WLJ80SS_MAP_16

Autonomous to LWAPP MigrationDefectsStatusDescriptionTitleLogical ID

PassedTo migrate theautonomous to LWAPP

Autonomous toLWAPPMigration

WLJ80S_Migration_01

PassedTo verify if autonomousAP is migrating to LAPimmediately using theoption " Schedule for laterdate/time"

NCS: migratingautonomous AP toLWAPP using the"Schedule for laterdate /time

WLJ80S_Migration_02


135

Regression Features - Test SummaryPI

Backup And Restore of PIDefectsStatusDescriptionTitleLogical ID

PassedTo verify the PI backupand restore is successful

Performing Backupand restore in PI

WLJ80S_BnR_81

PI HADefectsStatusDescriptionTitleLogical ID

PassedTo check whether PI hasbeen switchover to thesecondary when there is aprimary server(HW) failure-failover type as "Manual"

PI HA- Whenprimary server isdown(HW failure)and Failover type as"Manual"

WLJ76S_PI_HA_01

PassedTo check whether PI hasbeen switchover to thesecondary when there is aprimary server(HW) failure-failover type as "Automatic"

PI HA- Whenprimary server isdown(HW failure)and Failover type as"Automatic"

WLJ76S_PI_HA_02

PassedTo check whether PI hasbeen switchover to thesecondary when there is aprimary server(NW) failure-failover type as "Manual"

PI HA- Whenprimary server isdown(Networkfailure) and Failovertype as "Manual"

WLJ76S_PI_HA_03

PassedTo check whether PI hasbeen switchover to thesecondary when there is aprimary server(NW) failure-failover type as "Automatic"

PI HA- Whenprimary server isdown(Networkfailure) and Failovertype as "Manual"

WLJ76S_PI_HA_04

PassedTo check whether thefailback operation issuccessful after the primaryserver has been recoveredfrom HW failure

PI HA- Failback toPrimary server onceit has beenrecovered fromHWfailure

WLJ76S_PI_HA_05

PassedTo check whether thefailback operation issuccessful after the primaryserver has been recoveredfrom NW failure

PI HA- Failback toPrimary server onceit has beenrecovered fromNWfailure

WLJ76S_PI_HA_06


136

Regression Features - Test SummaryBackup And Restore of PI

MSE

MSE HADefectsStatusDescriptionTitleLogical ID

CSCum12763FailedTo verify whether MSEHA failover and fail backworks whenMSE systemhardware shutdown inDirect Connect Linkdeployment.

MSE systemhardware shutdownin Direct ConnectLink deployment

WLJ76S_MSE_HA_01

CSCum12763FailedTo verify whether MSEHA failover and fail backworks whenMSE systemhardware shutdown inNon-Direct Connect Linkdeployment.

MSE systemhardware shutdownin Non-DirectConnect Linkdeployment

WLJ76S_MSE_HA_01

CSCum12763FailedTo verify whether MSEHA failover and fail backworks when MSEnetwork shutdown inDirect Connect Linkdeployment.

MSE networkshutdown in DirectConnect Linkdeployment

WLJ76S_MSE_HA_02

CSCum12763FailedTo verify whether MSEHA failover and fail backworks when MSEnetwork shutdown inNon-Direct Connect Linkdeployment.

MSE networkshutdown in DirectNon-Connect Linkdeployment

WLJ76S_MSE_HA_02

SR Test CasesButton in Report Launch pad


PassedTo verify whether"Save", "Run andSave" button isworking in ReportLaunch pad in PI

PI: Save/Run buttonin Report Launchpad

WLJ80S_Reg_01


137

Regression Features - Test SummaryMSE

Map Location in Copy and Replace


PassedTo verify thesuccessful copy andreplace with MapLocation

Map Location inCopy and Replace

WLJ80S_Reg_02

Upload File


PassedTo verify whetherthe configurationupload from acontroller issuccessful

CT5508: ControllerconfigurationUpload using TFTPserver

WLJ80S_Reg_03



WLJ80S_Reg_04



WLJ80S_Reg_05

HREAP


PassedTo verify whetherthe client associatedto flexconnect APwill getre-associated in caseof fault tolerance


WLJ80S_Reg_06

PassedTo verify whetherthe client associatedto flexconnect APwill getre-associated in caseof fault tolerance


WLJ80S_Reg_07


138

Regression Features - Test SummarySR Test Cases

AP Fallback


PassedTo verify whetherthe client getsdisconnected or notwhen AP Fallbackfrom Secondary toPrimary WLC withenabling "APFallback" option inPrimary WLC onceit is UP.

Performing APfallback fromSecondary toPrimary WLC

WLJ80S_SR_01

PassedTo verify whetherthe client getsdisconnected or notwhen AP Fallbackfrom Secondary toPrimary WLC withenabling "APFallback" option inPrimary WLC at alltime.

Performing APfallback fromSecondary toPrimary WLC

WLJ80S_SR_02

Fault Tolerance


PassedTo verify whetherAP resets its radio ornot when it ismoving fromPrimary toSecondary WLCafter trying to joinPrimary WLC forlong time.

Performing Faulttolerance of FlexAP from Primary toSecondary WLC

WLJ80S_SR_03

PassedTo verify whetherAP resets its radio ornot when it ismoving fromPrimary toSecondary WLC .

Performing Faulttolerance of FlexAP from Primary toSecondary WLC

WLJ80S_SR_04


139



PassedTo verify whetherAP resets its radio ornot when it ismoving fromPrimary toSecondary WLCafter trying to joinPrimary WLC forlong time.

Performing Faulttolerance of AP inLocal mode fromPrimary toSecondary WLC

WLJ80S_SR_05

PassedTo verify whetherAP resets its radio ornot when it ismoving fromPrimary toSecondary WLC .

Performing Faulttolerance of AP inLocal mode fromPrimary toSecondary WLC

WLJ80S_SR_06

ISE


PassedTo Verify whetherISE shows the enduser device correctlyor not for HTTPprobe.

Checking the enduser device forHTTP probe in ISE

WLJ80S_SR_07

FlexConnect Enhancement


PassedTo verify whetherVLAN mapping isdone or not from APlevelWLAN-VLANmapping in aFlexConnect Group

Performing VLANmapping for aWLAN in aFlexConnect Groupwith 1142 AP - L2Security"Dot1x-Leap"

WLJ80S_SR_08


Performing VLANmapping for aWLAN in aFlexConnect Groupwith 1142 AP - L2Security"Dot1x-Peap"

WLJ80S_SR_09


140




Performing VLANmapping for aWLAN in aFlexConnect Groupwith 1262 AP - L2Security"Dot1x-Leap"

WLJ80S_SR_10


Performing VLANmapping for aWLAN in aFlexConnect Groupwith 1262 AP - L2Security"Dot1x-Peap"

WLJ80S_SR_11

WLC


PassedTo verify ChannelWidth of RFChannel Assignmentis not changing

Channel Width ofRF ChannelAssignment ischanged

WLJ80S_SR_12

PI


PassedTo verify if ms-lyncapplication isrecognized or not inPI

Validating ms-lyncapplication in PI

WLJ80S_SR_13

PassedTo verify if dashletdata is refreshedwhen time period indashlet is changed

Dashlet data isrefreshedwhen timeperiod in dashlet ischanged

WLJ80S_SR_14


141


Fix VerificationDefectsStatusDescriptionTitleLogical ID

PassedTo verify if the debug client outputon the 5508 controller shows the APname along with BSSID

AP name in debugclient output on the5508 controller

WLJ80S_Fix_01

PassedTo verify if the debug client outputon the 7500 and 8500 controllershows the AP name along withBSSID

AP name in debugclient output on the7500 and 8500controller

WLJ80S_Fix_02

PassedTo verify if the debug client outputon the WiSM2 controller shows theAP name along with BSSID

AP name in debugclient output on theWiSM2 controller

WLJ80S_Fix_03

PassedTo verify if the "show client detailmac-address" output shows theWLAN and profile name in 5508controller.

WLAN and Profilename in the showclient output on5508 seriescontroller

WLJ80S_Fix_04

PassedTo verify if the "show client detailmac-address" output shows theWLAN and profile name in7500/8500 controller.

WLAN and Profilename in the showclient output on7500/8500 seriescontroller

WLJ80S_Fix_05

PassedTo verify if the "show client detailmac-address" output shows theWLAN and profile name in WiSM2controller.

WLAN and Profilename in the showclient output onWiSM2 seriescontroller

WLJ80S_Fix_06

PassedTo verify if the MAP areauthenticated in the 5508 controllerusing LSC

LSC onlyauthentication forMAP in 5508 seriescontroller

WLJ80S_Fix_07

PassedTo verify if the MAP areauthenticated in the 7500/8500controller using LSC

LSC onlyauthentication forMAP in 7500/8500series controller

WLJ80S_Fix_08

PassedTo verify if the MAP areauthenticated in WiSM2 controllerusing LSC

LSC onlyauthentication forMAP in WiSM2series controller

WLJ80S_Fix_09


142

Regression Features - Test SummaryFix Verification


PassedTo verify if the old behavior ofMACfilter authentication for Mesh APs isnot affected in 5508 Controllers.

MAC filterauthentication forMAP in 5508 SeriesController

WLJ80S_Fix_10

PassedTo verify if the old behavior ofMACfilter authentication for Mesh APs isnot affected in 7500 Controllers.


WLJ80S_Fix_11

PassedTo verify if the old behavior ofMACfilter authentication for Mesh APs isnot affected in WiSM2 Controllers.

MAC filterauthentication forMAP in WiSM2Controller

WLJ80S_Fix_12

PassedTo enable/disable 'Flexconnect ARPcache' in 5508 and WiSM2controllers from GUI and check if itcould be applied successfully

Enable/DisableFlexconnect ARPcache from GUI ofthe 5508 Series andWiSM2 Controller

WLJ80S_Fix_13

PassedTo enable/disable 'Flexconnect ARPcache' in 7500 and 8500 controllersfrom GUI and check if it could beapplied successfully

Enable/DisableFlexconnect ARPcache from GUI ofthe 7500 and 8500series Controller

WLJ80S_Fix_14

PassedTo enable/disable 'Flexconnect ARPcache' in 5508 and WiSM2controllers from CLI and check if itcould be applied successfully

Enable/DisableFlexconnect ARPcache from CLI ofthe 5508 Series andWiSM2 Controller

WLJ80S_Fix_15

PassedTo enable/disable 'Flexconnect ARPcache' in 7500 and 8500 controllersfrom CLI and check if it could beapplied successfully

Enable/DisableFlexconnect ARPcache from CLI ofthe 7500 and 8500series Controller

WLJ80S_Fix_16

PassedTo check if the ARP request fromwired side doesn't reach theWirelessclient when the client is attached toa Flexconnect AP with locallyswitched WLAN.

Flexconnect ARPcache on locallyswitchedWLANs in5508 and WiSM2controllers.

WLJ80S_Fix_17

PassedTo check if the ARP request fromwired side doesn't reach theWirelessclient when the client is attached toa Flexconnect AP with locallyswitched WLAN.

Flexconnect ARPcache on locallyswitchedWLANs in7500 and 8500controllers.

WLJ80S_Fix_18


143



PassedTo check if the ARP request fromNGWC switch doesn't reach theWireless client when the client isattached to a Flexconnect AP withlocally switched WLAN.

Flexconnect ARPcache on locallyswitchedWLANs inall the modelcontrollers whenusing NGWCswitch

WLJ80S_Fix_19

PassedTo check the functionality of theglobal Telnet/SSH enable option inthe controller for the APs which areregistered to the controller

Global Telnet/SSHcommand on allLightweight APswhich are joined tothe controller

WLJ80S_Fix_20

PassedTo check if the user is able toTelnet/SSH a Mesh AP which hasobtained an IP address, but notjoined any controllers.

Telnet/SSH on aMesh APwhich hasnot joined thecontroller , butobtained an IPaddress

WLJ80S_Fix_21

PassedTo check the working of the newCLI command format for Telnet/SSH in terms of configuration andfunctionality

The new controllerCLI format forTelnet /SSH

WLJ80S_Fix_22

PassedTo check if the Per-AP configuredTelnet/SSH setting doesn't getoverridden by the controller's globalTelnet/SSH enabled setting.

A per-APconfiguredTelnet/SSH settingfunctionality whencontroller's globalTelnet/SSH settingis enabled

WLJ80S_Fix_23

PassedTo configure the 3600 AP to localmode from CLI of the AP and verifyif the configuration applies correctly

Configuring the AP3600 to Local modefrom the CLI

WLJ80S_Fix_24

PassedTo configure the 3600 AP to bridgemode from CLI of the AP and verifyif the configuration applies correctly

Configuring the AP3600 to bridgemode from the CLI

WLJ80S_Fix_25



WLJ80S_Fix_26



WLJ80S_Fix_27



WLJ80S_Fix_28


144





WLJ80S_Fix_29

PassedTo verify if Dot1X is rejected ifAirespace-WLAN-id does not matchvalue returned from AAA

WLAN Id attributewith Dot1x L2security on aWLAN

WLJ80S_Fix_30

PassedTo verify if Mac filtering is rejectedif Airespace-WLAN-id does notmatch value returned from AAA

WLAN Id attributewith Mac filteringon a WLAN

WLJ80S_Fix_31

PassedTo verify if Dot1X is rejected on aSSID based on values returned fromAAA server

SSID attribute withDot1x auth withsingle SSID

WLJ80S_Fix_32

PassedTo verify if Mac filtering is rejectedon a SSID based on values returnedfrom AAA server

SSID attribute withMac filtering authwith single SSID

WLJ80S_Fix_33

PassedTo verify if Dot1x is rejected on aSSID based on values returned fromAAA server

SSID attribute withDot1x Auth withmultiple SSIDs

WLJ80S_Fix_34

PassedTo verify if Mac filtering is rejectedon a SSID based on values returnedfrom AAA server

SSID attribute withMac filtering withmultiple SSIDs

WLJ80S_Fix_35

PassedTo verify if Web-auth is rejected ifAirespace-WLAN-id does not matchvalue returned from AAA

WLAN Id attributewith Web-auth on aWLAN

WLJ80S_Fix_36

PassedTo verify if Web-auth is rejected ona SSID based on values returnedfrom AAA server

SSID attribute withWeb-auth withsingle SSID

WLJ80S_Fix_37

PassedTo verify if Web-auth is rejected ona SSID based on values returnedfrom AAA server

SSID attribute withWeb-Auth withmultiple SSIDs

WLJ80S_Fix_38

PassedTo verify if multiple events((3events) are configured as triggeringby Location Change, "distance"value in CAS notification for thesecond and third event in addition tothe first event isa non-zero value

Multiple eventdefinition triggeredby location change

WLJ80S_Fix_39


145



PassedTo verify if multiple events(5 events)are configured as triggering byLocation Change, "distance" valuein CAS notification for the secondand third event in addition to the firstevent isa non-zero value


WLJ80S_Fix_40

PassedTo verify if notificationconfiguration for probing clientswhich are tracked by CAS/MSE, thenotifications over SOAP/Syslog aresent only once when the notificationhas "Non Recurring" as Frequencyconfiguration

Notification forMissing client

WLJ80S_Fix_41

PassedTo verify if notificationconfiguration for probing clientswhich are tracked by CAS/MSE, thenotifications over SOAP/Syslog aresent at a periodic interval when thenotification has " Recurring" asFrequency configuration


WLJ80S_Fix_42

PassedTo check if the MAC filteringtracking is faster .

MAC filteringparameter cache

WLJ80S_Fix_43

PassedTo verify if the CAPWAP data keepalive support exists or not from theAP to WLC when a NAT gatewayexists between them.

CAPWAPdata keepalive support

WLJ80S_Fix_44

PassedTo verify if the Transmit power levelremains the same in the APwhen theTransmit power level is set to 5 inthe controller >Wireless> 802.11aand b radio settings.

Tx Power level in3600 AP in Qdomain

WLJ80S_Fix_45



WLJ80S_Fix_46


Tx Power level in1042 AP in Adomain

WLJ80S_Fix_47


146





WLJ80S_Fix_48

TACDefectStatusDescriptionTitleLogical ID

CSCua30068Passed if the debugoutput shows the APname along withBSSID

To verify if thedebug client outputon the 5508controller shows theAP name along withBSSID

AP name in debugclient output on the5508 controller

WLJ80S_Fix_01


To verify if thedebug client outputon the 7500 and8500 controllershows the AP namealong with BSSID

AP name in debugclient output on the7500 and 8500controller

WLJ80S_Fix_02


To verify if thedebug client outputon the WiSM2controller shows theAP name along withBSSID

AP name in debugclient output on theWiSM2 controller

WLJ80S_Fix_03

CSCug72744Passed if the debugoutput shows theWLAN and profilename .

To verify if the"show client detailmac-address" outputshows the WLANand profile name in5508 controller.

WLAN and Profilename in the showclient output on5508 seriescontroller

WLJ80S_Fix_04


To verify if the"show client detailmac-address" outputshows the WLANand profile name in7500/8500controller.

WLAN and Profilename in the showclient output on7500/8500 seriescontroller

WLJ80S_Fix_05


147

Regression Features - Test SummaryTAC

DefectStatusDescriptionTitleLogical ID


To verify if the"show client detailmac-address" outputshows the WLANand profile name inWiSM2 controller.

WLAN and Profilename in the showclient output onWiSM2 seriescontroller

WLJ80S_Fix_06

CSCud56704Passed if the MAP isauthenticated usingLSC only.

To verify if theMAP areauthenticated in the5508 controllerusing LSC

LSC onlyauthentication forMAP in 5508 seriescontroller

WLJ80S_Fix_07


To verify if theMAP areauthenticated in the7500/8500controller usingLSC

LSC onlyauthentication forMAP in 7500/8500series controller

WLJ80S_Fix_08


To verify if theMAP areauthenticated inWiSM2 controllerusing LSC

LSC onlyauthentication forMAP in WiSM2series controller

WLJ80S_Fix_09

CSCud56704Passed if the oldbehavior is not affected

To verify if the oldbehavior of MACfilter authenticationfor Mesh APs is notaffected in 5508Controllers.


WLJ80S_Fix_10


To verify if the oldbehavior of MACfilter authenticationfor Mesh APs is notaffected in 7500Controllers.


WLJ80S_Fix_11


To verify if the oldbehavior of MACfilter authenticationfor Mesh APs is notaffected in WiSM2Controllers.

MAC filterauthentication forMAP in WiSM2Controller

WLJ80S_Fix_12


148



CSCty04398Passed if theFlexconnect ARPcache can beenabled/disabledwithout any issue.

To enable/disable'Flexconnect ARPcache' in 5508andWiSM2controllers fromGUI and check if itcould be appliedsuccessfully

Enable/DisableFlexconnect ARPcache from GUI ofthe 5508 Series andWiSM2 Controller

WLJ80S_Fix_13


To enable/disable'Flexconnect ARPcache' in 7500 and8500 controllersfromGUI and checkif it could be appliedsuccessfully

Enable/DisableFlexconnect ARPcache from GUI ofthe 7500 and8500series Controller

WLJ80S_Fix_14


To enable/disable'Flexconnect ARPcache' in 5508andWiSM2controllers fromCLIand check if it couldbe appliedsuccessfully

Enable/DisableFlexconnect ARPcache from CLI ofthe 5508 Series andWiSM2 Controller

WLJ80S_Fix_15


To enable/disable'Flexconnect ARPcache' in 7500 and8500 controllersfrom CLI and checkif it could be appliedsuccessfully

Enable/DisableFlexconnect ARPcache from CLI ofthe 7500 and8500series Controller

WLJ80S_Fix_16

CSCty04398Passed if the ARPrequest doesn't reachthe wireless client andthe AP replies to thewired side.

To check if the ARPrequest from wiredside doesn't reachthe Wireless clientwhen the client isattached to aFlexconnect APwith locallyswitched WLAN.

Flexconnect ARPcache on locallyswitchedWLANs in5508 and WiSM2controllers.

WLJ80S_Fix_17


149




To check if the ARPrequest from wiredside doesn't reachthe Wireless clientwhen the client isattached to aFlexconnect APwith locallyswitched WLAN.

Flexconnect ARPcache on locallyswitchedWLANs in7500 and 8500controllers.

WLJ80S_Fix_18


To check if the ARPrequest fromNGWC switchdoesn't reach theWireless clientwhen the client isattached to aFlexconnect APwith locallyswitched WLAN.

Flexconnect ARPcache on locallyswitchedWLANs inall the modelcontrollers whenusing NGWCswitch

WLJ80S_Fix_19

CSCud56714Passed if theTelnet/SSH is workingas expected.

To check thefunctionality of theglobal Telnet /SSHenable option in thecontroller for theAPs which areregistered to thecontroller

Global Telnet /SSHcommand on allLightweight APswhich are joined tothe controller

WLJ80S_Fix_20

CSCud56714Passes if the user isable to Telnet/SSH theMesh AP

To check if the useris able toTelnet/SSH a MeshAP which hasobtained an IPaddress, but notjoined anycontrollers.

Telnet/SSH on aMesh AP which hasnot joined thecontroller , butobtained an IPaddress

WLJ80S_Fix_21

CSCud56714Passed if worked asexpected

To check theworking of the newCLI commandformat forTelnet/SSH interimsof configuration andfunctionality

The new controllerCLI format forTelnet/SSH

WLJ80S_Fix_22


150



CSCud56714Passed if the globalsetting doesn't overridethe per-AP configuredTelnet /SSH setting

To check if thePer-AP configuredTelnet /SSH settingdoesn't getoverridden by thecontroller's globalTelnet /SSH enabledsetting.

A per-APconfiguredTelnet/SSH settingfunctionality whencontroller's globalTelnet/SSH settingis enabled

WLJ80S_Fix_23

CSCug82223Passed if the AP modeis changed to local

To configure the3600 AP to localmode from CLI ofthe AP and verify ifthe configurationapplies correctly


WLJ80S_Fix_24

CSCug82223Passed if the AP modeis changed to bridge.

To configure the3600 AP to bridgemode from CLI ofthe AP and verify ifthe configurationapplies correctly


WLJ80S_Fix_25




WLJ80S_Fix_26




WLJ80S_Fix_27




WLJ80S_Fix_28




WLJ80S_Fix_29


151



CSCsj27376Passed if worked asexpected

To verify if Dot1Xis rejected ifAirespace-WLAN-iddoes not matchvalue returned fromAAA

"WLAN Id attributewith Dot1x L2security on aWLAN "

WLJ80S_Fix_30


To verify if Macfiltering is rejectedifAirespace-WLAN-iddoes not matchvalue returned fromAAA

"WLAN Id attributewith Mac filteringon a WLAN"

WLJ80S_Fix_31


To verify if Dot1Xis rejected on aSSID based onvalues returned fromAAA server

"SSID attribute withDot1x auth withsingle SSID"

WLJ80S_Fix_32


To verify if Macfiltering is rejectedon a SSID based onvalues returned fromAAA server

"SSID attribute withMac filtering authwith single SSID"

WLJ80S_Fix_33


To verify if Dot1x isrejected on a SSIDbased on valuesreturned from AAAserver

SSID attribute withDot1x Auth withmultiple SSIDs

WLJ80S_Fix_34


To verify if Macfiltering is rejectedon a SSID based onvalues returned fromAAA server

SSID attribute withMac filtering withmultiple SSIDs

WLJ80S_Fix_35


To verify ifWeb-auth is rejectedifAirespace-WLAN-iddoes not matchvalue returned fromAAA

"WLAN Id attributewith Web-auth on aWLAN"

WLJ80S_Fix_36


To verify ifWeb-auth is rejectedon a SSID based onvalues returned fromAAA server

"SSID attribute withWeb-auth withsingle SSID"

WLJ80S_Fix_37


152




To verify ifWeb-auth is rejectedon a SSID based onvalues returned fromAAA server

SSID attribute withWeb-Auth withmultiple SSIDs

WLJ80S_Fix_38

CSCuh00581Passed if the CASnotification for thesecond and third eventis also received to anon-zero value

"To verify ifmultiple events((3events) areconfigured astriggering byLocationChange,""distance""value in CASnotification for thesecond and thirdevent in addition tothe first event isanon-zero value "


WLJ80S_Fix_39

CSCuh00581Passed if the CASnotification for thesecond and third eventis also received to anon-zero value

"To verify ifmultiple events(5events) areconfigured astriggering byLocationChange,""distance""value in CASnotification for thesecond and thirdevent in addition tothe first event isanon-zero value "


WLJ80S_Fix_40

CSCuj12261Passed if thenotification is sent onlyonce

To verify ifnotificationconfiguration forprobing clientswhich are trackedby CAS/MSE, thenotifications overSOAP/Syslog aresent only once whenthe notification has"Non Recurring" asFrequencyconfiguration


WLJ80S_Fix_41


153



CSCuj12261Passed if thenotifications is sent outat the configuredinterval In a recurringfashion

To verify ifnotificationconfiguration forprobing clientswhich are trackedby CAS/MSE, thenotifications overSOAP/Syslog aresent at a periodicinterval when thenotification has "Recurring" asFrequencyconfiguration


WLJ80S_Fix_42

CSCug46654Passed if worked asexpected.

To check if theMAC filteringtracking is faster .

MAC filteringparameter cache

WLJ80S_Fix_43

CSCsq48449Passed if the persistsTo verify if theCAPWAPdata keepalive support existsor not from the APto WLC when aNAT gateway existsbetween them.

CAPWAPdata keepalive support

WLJ80S_Fix_44

WLC_SecurityDefectsStatusDescriptionTitleLogical ID

PassedTo check whether Win7 client getsde-authenticated or notbefore EAP-identitytimeout expires.

PerformingEAP-Identityfunction in Win 7client with Dot1xsecurity

WLJ80S_Sec_01


PerformingEAP-Identityfunction in Win 7client withWPA2+Dot1xsecurity

WLJ80S_Sec_02


154

Regression Features - Test SummaryWLC_Security


PerformingEAP-Identityfunction in Win 8client with Dot1xsecurity

WLJ80S_Sec_03

PassedTo check whetherAppleMacBook clientgets de-authenticatedor not beforeEAP-identity timeoutexpires.

PerformingEAP-Identityfunction in AppleMacBook clientwith Dot1x security

WLJ80S_Sec_04

PassedTo check whether Win7 client roams betweenAP's in a 5500 WLCand gets ip from vlanmapped in thatWLANwith AAA overrideenabled.

Roaming a clientbetween AP's in5500 WLC withAAA overrideenabled.

WLJ80S_Sec_05

PassedTo check whether Win7 client roams betweenAP's in a 2500 WLCand gets ip from vlanmapped in thatWLANwith AAA overrideenabled.

Roaming a clientbetween AP's in2500 WLC withAAA overrideenabled.

WLJ80S_Sec_06

PassedTo check whether Win7 client is associated ornot to Dot1x WLANwith EAP-TLSmethod.

PerformingEAP-TLS methodwith Win 7 client.

WLJ80S_Sec_07

PassedTo check whetherAppleMacBook clientis associated or not toDot1x WLAN withEAP-TLS method.

PerformingEAP-TLS methodwith AppleMacBook client.

WLJ80S_Sec_08

PassedTo check whethernas-id shown in AAAserver is "systemnas-id" or nas-idmapped in WLANwhile performingdot1x security.

Performing Dot1xin 5500 & 2500WLC's andchecking the nas-idin AAA server.

WLJ80S_Sec_09


155


PassedTo check whethernas-id shown in AAAserver is "systemnas-id" or nas-idmapped in WLANwhile performingdot1x security.

Performing Dot1xin 8500 & vWLC'sand checking thenas-id in AAAserver.

WLJ80S_Sec_10

PassedTo check whether NTPsever & WLC are insync or not via SNMPTrap log whilerebooting the WLC.

Configuring Routeras NTP server in5500 WLC & NCSand checking thesync via SNMPTrap log.

WLJ80S_Sec_11


Configuring 5500WLC asNTP serverin NCS andchecking the Syncvia SNMP Trap log.

WLJ80S_Sec_12


Configuring Routeras NTP server in8500 WLC & NCSand checking thesync via SNMPTrap log.

WLJ80S_Sec_13


Configuring 8500WLC asNTP serverin NCS andchecking the Syncvia SNMP Trap log.

WLJ80S_Sec_14


Configuring Routeras NTP server invWLC & NCS andchecking the syncvia SNMP Trap log.

WLJ80S_Sec_15


Configuring vWLCas NTP server inNCS and checkingthe Sync via SNMPTrap log.

WLJ80S_Sec_16

PassedTo check whether theconfigurations ofRadius NAC isretained or not onceWLC gets rebooted.

Enabling RADIUSNAC for a WLANin 5500 WLC.

WLJ80S_Sec_17


156



Enabling RADIUSNAC for a WLANin 8500 WLC.

WLJ80S_Sec_18


Enabling RADIUSNAC for a WLANin vWLC.

WLJ80S_Sec_19

PassedTo check whether theconfigurations ofRadius NAC isretained or not afterUpload/download theconfig file via TFTP.

Checking theRadius NACconfiguration inWLC GUI afterUpload/downloadthe config file viaTFTP.

WLJ80S_Sec_20

PassedTo check whether Win7 client gets roamed ornot from HA WLC to8500 WLC and alsocheckingwhether errormessage displays ornot in Syslogmessages.

Roaming a Win 7client from 5500HA WLC to 8500WLC.

WLJ80S_Sec_21

PassedTo check whether Win8 client gets roamed ornot from HA WLC to8500 WLC and alsocheckingwhether errormessage displays ornot in Syslogmessages.

Roaming a Win 8client from 5500HA WLC to 8500WLC.

WLJ80S_Sec_22

PassedTo check whetherAppleMacBook clientgets roamed or notfromHAWLC to 8500WLC and alsocheckingwhether errormessage displays ornot in Syslogmessages.

Roaming a AppleMacBook clientfrom 5500 HAWLC to 8500WLC.

WLJ80S_Sec_23


157


PassedTo check whetherLocal policies(namewhich contain specialcharacters) getsretained or not inWLCafter Upload/downloadthe config file.

Checking theconfigurations ofLocal policy in 5500WLC afterUpload/downloadthe config file.

WLJ80S_Sec_24



WLJ80S_Sec_25



WLJ80S_Sec_26


Checking theconfigurations ofLocal policy inWiSM2 afterUpload/downloadthe config file.

WLJ80S_Sec_27

PassedTo check whethernac-alert is shown inSNMP Trap log list ornot when nac-client isassociated to WLC.

Enabling Nac-Alertin 5500 WLC andchecking the SNMPTraplog's whileassociating anac-client.

WLJ80S_Sec_28



WLJ80S_Sec_29



WLJ80S_Sec_30


158


PassedTo check whether errormessage dispayed ornot in WLC consolewhen 150 WLAN's &100 Apgroups arecreated in WLC GUI.

Creating 150WLAN's & 100APgroups in 5500WLC and checkingthe WLC Console.

WLJ80S_Sec_31

PassedTo check whetherwhen client tries toassociate a WLANwith different L2Security but SSIDbeing same andchecking the messagelog whether it displayscorrect error messageor not.

Associating aWin 7client to aWLAN(WPA2+PSK)with WEP in 5500WLC and checkingthe message log.

WLJ80S_Sec_32


Associating aWin 7client to aWLAN(WPA2+PSK)with WEP in 8500WLC and checkingthe message log.

WLJ80S_Sec_33


Associating aWin 7client to aWLAN(WPA2+PSK)withWEP in vWLCand checking themessage log.

WLJ80S_Sec_34


Associating aWin 7client to aWLAN(WPA2+PSK)with WEP inWiSM2 andchecking themessage log.

WLJ80S_Sec_35


159


PassedTo checkwhether 7921IPphone able toassociate or not withCCKM enabledWLAN.

Associating 7921IPphone to CCKMenabled WLAN in5500 WLC.

WLJ80S_Sec_36



WLJ80S_Sec_37



WLJ80S_Sec_38



WLJ80S_Sec_39

PassedTo checkwhether 7921&7925 IPphones areassociated or not withCCKM enabledWLAN and checkingthe voice call betweenthem.

Associating 7921 &7925 IPphones toCCKM enabledWLAN inWLCandchecking the voicecall between them.

WLJ80S_Sec_40

PassedTo check whether bychanging thecredentials periodicallyfrom Machine to usercredentials andchecking whetherclients getsde-authenticated or notwhile credentialschange.

Associate a Win 7client to WLANwith security Dot1xand change thecredentialsperiodically.

WLJ80S_Sec_41

PassedTo check whether bychanging thecredentials periodicallyfrom Machine to usercredentials andchecking whetherclients getsde-authenticated or notwhile credentialschange.

Associate aMacBook client toWLAN withsecurity Dot1x andchange thecredentialsperiodically.

WLJ80S_Sec_42


160


PassedTo check whether bychanging thecredentials periodicallyfrom Machine to usercredentials andchecking whetherclients getsde-authenticated or notwhile credentialschangewith Fast SSIDchange enabled.

Associate a Win 7client to WLANwith security Dot1xand change thecredentialsperiodically withFast SSID enabled.

WLJ80S_Sec_43

PassedTo check whether bychanging thecredentials periodicallyfrom Machine to usercredentials andchecking whetherclients getsde-authenticated or notwhile credentialschangewith Fast SSIDchange enabled.

Associate a AppleMacBook client toWLAN withsecurity Dot1x andchange thecredentialsperiodically withFast SSID enabled.

WLJ80S_Sec_44

PassedTo check whetherRadius serverconfiguration gettingsync or not betweenActive & StandbyWLC's.

Checking the Syncof Radius Serverconfiguration in HAWLC's.

WLJ80S_Sec_45

PassedTo check whetherclient gets connectedor not when name ofthe User changedslightly whileconnecting secondtime.

Changing the nameof User whileWin 7client associating toDot1x security.

WLJ80S_Sec_46

PassedTo check whetherclient gets connectedor not when name ofthe User changedslightly whileconnecting secondtime.

Changing the nameof User whileMacBook clientassociating to Dot1xsecurity.

WLJ80S_Sec_47


161


PassedTo check whetherclient gets connectedor not when name ofthe User changedslightly whileconnecting secondtime and also changingthe EAP methodduring association ofsecond time.

Changing the nameof User and alsochanging the EAPmethods while Win7 client associatingto Dot1x security.

WLJ80S_Sec_48

PassedTo check whether Win8 client gets associatedor not withWPA2+AES+PSKenabled WLAN in5500 WLC.

Associating Win 8client to WPA2+AES+ PSK in 5500WLC.

WLJ80S_Sec_49

PassedTo check whether Win8 client gets associatedor not withWPA2+AES+PSKenabled WLAN in8500 WLC.

Associating Win 8client to WPA2+AES+ PSK in 8500WLC.

WLJ80S_Sec_50

PassedTo check whether Win8 client gets associatedor not withWPA2+AES+PSKenabled WLAN invWLC.

Associating Win 8client to WPA2+AES+ PSK invWLC.

WLJ80S_Sec_51

PassedTo check whether Win8 client gets associatedor not withWPA2+AES+Dot1xenabled WLAN in5500 WLC.

Associating Win 8client to WPA2+AES+ Dot1x in5500 WLC.

WLJ80S_Sec_52

PassedTo check whether Win8 client gets associatedor not withWPA2+AES+Dot1xenabled WLAN in8500 WLC.

Associating Win 8client to WPA2+AES+ Dot1x in8500 WLC.

WLJ80S_Sec_53

PassedTo check whether Win8 client gets associatedor not withWPA2+AES+Dot1xenabled WLAN invWLC.

Associating Win 8client to WPA2+AES+ Dot1x invWLC.

WLJ80S_Sec_54


162


PassedTo check whether Win8 client gets associatedor not withWPA2+AES+Dot1xenabled WLAN inWiSM2.

Associating Win 8client to WPA2+AES+ Dot1x inWiSM2.

WLJ80S_Sec_55

PassedTo check whetherMessage authenticatorcode goes to zero bitsor not in RadiusAccess-Request packetwhen RadiusCompatibility modechanged from CiscoACS to Free RADIUSusing Wireshark

Capturing theRadiusAccess-Requestpacket usingWireshark.

WLJ80S_Sec_56

PassedTo check whether MacFiltering works or notwhile using MultipleRadius Server in aFlexconnect group in5500 WLC.

Performing MacFiltering in 5500WLC usingMultiple RadiusServer.

WLJ80S_Sec_57

PassedTo check whether MacFiltering works or notwhile using MultipleRadius Server in aFlexconnect group in5500 WLC.

Performing MacFiltering in 8500WLC usingMultiple RadiusServer.

WLJ80S_Sec_58

PassedTo check whetherconfigurations of clientexclusion value getsretained or not afterUpload/download theconfig file in 2500WLC.

Checking theconfiguration ofclient exclusionvalue in a WLANafterUpload/downloadthe config file in2500 WLC.

WLJ80S_Sec_59

PassedTo check whetherconfigurations of clientexclusion value getsretained or not afterUpload/download theconfig file in vWLC.

Checking theconfiguration ofclient exclusionvalue in a WLANafterUpload/downloadthe config file invWLC.

WLJ80S_Sec_60


163


PassedTo check whethermgmt user login isauthenticated or not byTACACS server.

VerfiyingManagement userlogin usingTACACS server.

WLJ80S_Sec_61

PassedTo check whethermgmt user login isauthenticated or not byTACACS server afterchanging thecredentials in bothWLC & TACACSserver which is lesservalue than first one.

Changing thecredentials ofManagement Userfor second time inWLC & verfiying itusing TACACSserver.

WLJ80S_Sec_62

PassedTo check whether errormessage occurs or notin msglog of WLC-Awhile client moves toWLC-B & web-authtimeout occurs whileassociating toWLC-B.

Roaming a Win 7client betweenWLC's withSecurity asWeb-auth andchecking theWeb-auth timeoutfunction.

WLJ80S_Sec_63

PassedTo check whether errormessage occurs or notin msglog of WLC-Awhile client moves toWLC-B & web-authtimeout occurs whileassociating toWLC-B.

Roaming a AppleMacBook clientbetween WLC'swith Security asWeb-auth andchecking theWeb-auth timeoutfunction.

WLJ80S_Sec_64

PassedTo check whetherconfigurations ofStatic-wep-encryptionvalue gets retained ornot afterUpload/download theconfig file in 2500WLC.

Checking theconfiguration ofStatic-wep-encryptionin a WLAN afterUpload/downloadthe config file in2500 WLC.

WLJ80S_Sec_65

PassedTo check whetherconfigurations ofStatic-wep-encryptionvalue gets retained ornot afterUpload/download theconfig file in vWLC.

Checking theconfiguration ofStatic-wep-encryptionin a WLAN afterUpload/downloadthe config file invWLC.

WLJ80S_Sec_66


164


PassedTo check whetherconfigurations ofStatic-wep-encryptionvalue gets retained ornot afterUpload/download theconfig file in 8500WLC.

Checking theconfiguration ofStatic-wep-encryptionin a WLAN afterUpload/downloadthe config file in8500 WLC.

WLJ80S_Sec_67

PassedTo check whetherRadius server fallbackoccurs or not whenPrimary Server isdown.

Performing RadiusServer fallback.

WLJ80S_Sec_68

PassedTo check whetherconfigurations ofSNMP parameters getsretained or not afterUpload/download theconfig file in 8500WLC.

Checking theconfiguration ofSNMPparameters(users &communities) afterUpload/downloadthe config file in8500 WLC.

WLJ80S_Sec_69

PassedTo check whetherconfigurations ofSNMP parameters getsretained or not afterUpload/download theconfig file in 5500WLC.

Checking theconfiguration ofSNMPparameters(users &communities) afterUpload/downloadthe config file in5500 WLC.

WLJ80S_Sec_70

PassedTo check whetherconfigurations ofSNMP parameters getsretained or not afterUpload/download theconfig file in WiSM2.

Checking theconfiguration ofSNMPparameters(users &communities) afterUpload/downloadthe config file inWiSM2.

WLJ80S_Sec_71

PassedTo check whetherconfigurations of802.11a advancedparameters getsretained or not afterUpload/download theconfig file in 2500WLC.

Checking theconfiguration of802.11a advancedparameters afterUpload/downloadthe config file in2500 WLC.

WLJ80S_Sec_72


165


PassedTo check whetherconfigurations of802.11a advancedparameters getsretained or not afterUpload/download theconfig file in vWLC.

Checking theconfiguration of802.11a advancedparameters afterUpload/downloadthe config file invWLC.

WLJ80S_Sec_73

PassedTo check whetherconfigurations of802.11a advancedparameters getsretained or not afterUpload/download theconfig file in 8500WLC.

Checking theconfiguration of802.11a advancedparameters afterUpload/downloadthe config file in8500 WLC.

WLJ80S_Sec_74

PassedTo check whethertraceback messageoccurs or not in 5500WLCwhile associatingWin 7 client to Dot1xWLAN.

Associating Win 7client to Dot1xsecurity in 5500WLC and checkingthe message log.

WLJ80S_Sec_75

PassedTo check whethertraceback messageoccurs or not in 8500WLCwhile associatingAppleMacBook clientto Dot1x WLAN.

Associating AppleMacBook client toDot1x security in8500 WLC andchecking themessage log.

WLJ80S_Sec_76

PassedTo check whetheraccounting functionworks or not in 5500WLC by associatingWin 7 client to ISE.

PerformingAccounting in 5500WLC using RadiusServer as ISE.

WLJ80S_Sec_77

PassedTo check whether falsewIPS alarm isproduced or not in PIfor neighbor AP's asrogue in other WLCwhen configured insame mobility group.

Checking the wIPSalarm in PI.

WLJ80S_Sec_79


166


PassedTo check whetherclients associated ornot to LocallyswitchingWLANwithStaticWEP +Dot1x in5500 WLC and checkwhether ping functionworks or not betweenthe clients.

Associating 2clients to WLANwith security StaticWEP + Dot1x in5500 WLC andchecking the pingfunction betweenthe clients.

WLJ80S_Sec_83

PassedTo check whetherclients associated ornot to LocallyswitchingWLANwithStaticWEP +Dot1x in8500 WLC and checkwhether ping functionworks or not betweenthe clients.

Associating 2clients to WLANwith security StaticWEP + Dot1x in8500 WLC andchecking the pingfunction betweenthe clients.

WLJ80S_Sec_84

PassedTo check whether clicommands displays theoutput correctly or notwhen client isassociated to AP in2500 WLC.

Checking the CLIcommand "showclient ap 802.11b<Apname>" in 2500WLCwhile client isin idle state.

WLJ80S_Sec_85

AP_OEAPDefectsStatusDescriptionTitleLogical ID

PassedTo check whetherchannel is same inWLC GUI/CLI &OEAP GUI after theassociation of OEAPto 5500 WLC.

Associating OEAPto 5500 WLC andchecking thechannels in WLCGUI/CLI & OEAPGUI.

WLJ80S_oeap_01



WLJ80S_oeap_02


167

Regression Features - Test SummaryAP_OEAP



WLJ80S_oeap_03

PassedTo check whetherWin 7 client getsthroughput more than50 Mbps or not whenit is connected toPersonal SSID ofOEAP using FTP.

Associating a Win7 Client to OEAPPersonal SSID andchecking thethroughput of theclient.

WLJ80S_oeap_04

PassedTo check whetherWin 8 client getsthroughput more than50 Mbps or not whenit is connected toPersonal SSID ofOEAP using FTP.

Associating a Win8 Client to OEAPPersonal SSID andchecking thethroughput of theclient.

WLJ80S_oeap_05

PassedTo check whetherWin 7 client goes toidle state or not whenit moves out of rangeof OEAP.

Checking the idletimeout functionfor Win 7 clientwhen it isconnected toOEAP.

WLJ80S_oeap_06

PassedTo check whetherWin 8 client goes toidle state or not whenit moves out of rangeof OEAP.

Checking the idletimeout functionfor Win 8 clientwhen it isconnected toOEAP.

WLJ80S_oeap_07

PassedTo check whetherApple MacBookclient goes to idlestate or not when itmoves out of range ofOEAP.

Checking the idletimeout functionfor AppleMacbookclient when it isconnected toOEAP.

WLJ80S_oeap_08

PassedTo check whetherAndroid client goes toidle state or not whenit moves out of rangeof OEAP.

Checking the idletimeout functionfor Android clientwhen it isconnected toOEAP.

WLJ80S_oeap_09


168

Regression Features - Test SummaryAP_OEAP

PassedTo check whetherstatic ip configuredfor AP in its localGUI is shown or notin 5500 WLC CLI.

Associating OEAPto 5500 WLC andassigning static IPto OEAP in itslocal GUI andchecking AP ip inWLC CLI.

WLJ80S_oeap_10



WLJ80S_oeap_11



WLJ80S_oeap_12

PassedTo check whetherprivate address ispingable or not fromWAN port of OEAP.

Connecting WANport of OEAP torouter port andpinging the privateaddress in router.

WLJ80S_oeap_13

WLC_HREAPDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether theclient gets stuck in theDHCP required stateor not

Client connection toa WLAN in localswitchingwithDHCPrequired enabled

WLJ80S_wlchreap_01

PassedTo verify whether theclient gets stuck in theDHCP required stateor not

Client connection toa WLAN in centralswitchingwithDHCPrequired enabled

WLJ80S_wlchreap_02

PassedTo verify whether theWLC keeps ghostclient entry or not

Ghost client entry inWLC - Localswitching

WLJ80S_wlchreap_03

PassedTo verify whether theWLC keeps ghostclient entry or not

Ghost client entry inWLC - Centralswitching

WLJ80S_wlchreap_04


169

Regression Features - Test SummaryWLC_HREAP

PassedTo verify whether theNCS LightWeight APTemplate is correctlyapplied to the AP ornot

Applying NCS LightWeight AP Templateto AP

WLJ80S_wlchreap_07

PassedTo verify whether theNCS LightWeight APTemplate is correctlyapplied to the AP ornot

Applying NCS LightWeight AP Templateto AP-3600/3700with module inserted

WLJ80S_wlchreap_08

PassedTo verify whether theWindows 7 clients aregetting disconnectedand connected back ornot when ethernetcable is disconnectedand connected backto/from the APpowered by ACadapter

Ethernet cabledisconnection in APpowered by ACadapter - Windows 7Client

WLJ80S_wlchreap_09

PassedTo verify whether theApple MAC Bookclients are gettingdisconnected andconnected back or notwhen ethernet cable isdisconnected andconnected backto/from the APpowered by ACadapter

Ethernet cabledisconnection in APpowered by ACadapter - AppleMACBook Client

WLJ80S_wlchreap_10

PassedTo verify whether theSamsung S4 Mobileclients are gettingdisconnected andconnected back or notwhen ethernet cable isdisconnected andconnected backto/from the APpowered by ACadapter

Ethernet cabledisconnection in APpowered by ACadapter - Samsung S4Mobile Client

WLJ80S_wlchreap_11


170


PassedTo verify whether theApple iphone clientsare gettingdisconnected andconnected back or notwhen ethernet cable isdisconnected andconnected backto/from the APpowered by ACadapter

Ethernet cabledisconnection in APpowered by ACadapter - Appleiphone Client

WLJ80S_wlchreap_12

PassedTo verify whetherWLC is reportingduplicate associationidentifier entries forthe clients associatedto it or not

Duplicate associationidentifier entries forHREAP Windows 7clients

WLJ80S_wlchreap_13


Duplicate associationidentifier entries forHREAP Apple MACBook clients

WLJ80S_wlchreap_14


Duplicate associationidentifier entries forHREAP Samsung S4Mobile clients

WLJ80S_wlchreap_15


Duplicate associationidentifier entries forHREAP Appleiphone clients

WLJ80S_wlchreap_16

PassedTo verify whether thebroadcasts suchs asARP are received inthe wireless clients ornot

Receiving broadcastsin wireless clients

WLJ80S_wlchreap_19

PassedTo verify whether thebroadcasts suchs asARP are received inthe wireless clients ornot when VLAN isconfigured

Receiving broadcastsin wireless clients -with VLAN enabled

WLJ80S_wlchreap_20


171


PassedTo verify whether theWindows 7 client IPaddress is displayedcorrectly in the WLCor not

Windows 7 Client IPWLJ80S_wlchreap_21

PassedTo verify whether theApple MAC Bookclient IP address isdisplayed correctly inthe WLC or not

Apple MAC BookClient IP

WLJ80S_wlchreap_22

PassedTo verify whether theSamsung S4 Mobileclient IP address isdisplayed correctly inthe WLC or not

Samsung S4 MobileClient IP

WLJ80S_wlchreap_23

PassedTo verify whether theApple iphone client IPaddress is displayedcorrectly in the WLCor not

Apple iphone ClientIP

WLJ80S_wlchreap_24

PassedTo verify whetherVLAN mapping ispreserved after APfailover or not

HREAP VLANMapping

WLJ80S_wlchreap_25

PassedTo verify whetherdifferent bridge IDsare assigned to thedifferentsub-interfaces of theAP after failover ornot

Bridge-group IDassignation tosub-interfaces in AP

WLJ80S_wlchreap_26

PassedTo verify whetherdifferent bridge IDsare assigned to thedifferentsub-interfaces of theAP after failover ornot

Bridge-group IDassignation tosub-interfaces in AP- by configuring APGroup

WLJ80S_wlchreap_27

PassedTo verify whether APsends GTK updatesused for broadcasttraffic encryption to itscurrent Windows 7clients

GTK Updates usedfor broadcast trafficencryption - ForWindows 7 Clients

WLJ80S_wlchreap_28


172


PassedTo verify whether APsends GTK updatesused for broadcasttraffic encryption to itscurrent Apple MACclients

GTK Updates usedfor broadcast trafficencryption - ForApple MAC BookClients

WLJ80S_wlchreap_29

PassedTo verify whether theWindows 7 clientprotocol is displayedcorrectly in the WLCafter HREAP faulttolerance or not

Client protocol afterHREAP faulttolerance - Windows7 Client

WLJ80S_wlchreap_30

PassedTo verify whether theApple MAC Bookclient protocol isdisplayed correctly inthe WLC afterHREAP faulttolerance or not

Client protocol afterHREAP faulttolerance - AppleMAC Book Client

WLJ80S_wlchreap_31

PassedTo verify whether theSamsung S4 Mobileclient protocol isdisplayed correctly inthe WLC afterHREAP faulttolerance or not

Client protocol afterHREAP faulttolerance - SamsungS4 Mobile Client

WLJ80S_wlchreap_32

PassedTo verify whether theApple iphone clientprotocol is displayedcorrectly in the WLCafter HREAP faulttolerance or not

Client protocol afterHREAP faulttolerance - Appleiphone Client

WLJ80S_wlchreap_33

PassedTo verify whether theWindows 7 client isprompted forweb-authenticationafter inter-controllerroaming or not

Web-authenticationafter inter-controllerroaming - Windows7 Client

WLJ80S_wlchreap_34

PassedTo verify whether theApple MAC Bookclient is prompted forweb-authenticationafter inter-controllerroaming or not

Web-authenticationafter inter-controllerroaming - AppleMAC Book Client

WLJ80S_wlchreap_35


173


CSCup87391Passed withexception

To verify whether theclient count isdisplayed correctly inthe Attached Clientsfield or not

Client countdisplayed in AttachedClients field - Localswitching

WLJ80S_wlchreap_36


To verify whether theclient count isdisplayed correctly inthe Attached Clientsfield or not

Client countdisplayed in AttachedClients field - Centralswitching

WLJ80S_wlchreap_37

PassedTo verify whether theVLAN mappings arechanged after HREAPLocal Switching APreboot or not

VLAN mappingsafter HREAP LocalSwitching AP reboot

WLJ80S_wlchreap_38

PassedTo verify whether theVLAN mappings arechanged after HREAPCentral Switching APreboot or not

VLAN mappingsafter HREAP CentralSwitching AP reboot

WLJ80S_wlchreap_39

PassedTo verify whether bothAP and WLCassociation countermatches or not

AP and WLCAssociation Counter- Windows 7 Client

WLJ80S_wlchreap_41

PassedTo verify whether bothAP and WLCassociation countermatches or not

AP and WLCAssociation Counter- Apple MAC BookClient

WLJ80S_wlchreap_42

PassedTo verify whetherWLAN and L2ACLconfig is preserved ornot after transferringthe run-config from5500,2504 seriesWLC

Transferringrun-config - 5500,2504 Series WLC

WLJ80S_wlchreap_43

PassedTo verify whetherWLAN and L2ACLconfig is preserved ornot after transferringthe run-config from7500 series WLC

Transferringrun-config - 7500Series WLC

WLJ80S_wlchreap_44


174


PassedTo verify whetherWLAN and L2ACLconfig is preserved ornot after transferringthe run-config fromWISM series WLC

Transferringrun-config - WISMSeries WLC

WLJ80S_wlchreap_45

LWAPP-AP-SWDefectsStatusDescriptionTitleLogical ID

PassedTo verify whetherAP's capwapconnection to theWLC is lost or notwhen 100 mbpsethernet channel isused

AP using 100 mbpsEthernet Channel -with 5500, 2504WLC

WLJ80S_lwapp_01


AP using 100 mbpsEthernet Channel -with 7500 WLC

WLJ80S_lwapp_02


AP using 100 mbpsEthernet Channel -with WISM WLC

WLJ80S_lwapp_03

PassedTo verify whether"lwapp ap" execcommandworks inAPCLI or not

"lwapp ap" Exec APcommand for Ease ofDeploy

WLJ80S_lwapp_04

PassedTo verify whetherthere is anyinformational tracebacks found when APIOS Booting up inRecovery image withNo Ethernet Link

AP IOS Booting upin Recovery imagewith No EthernetLink

WLJ80S_lwapp_05


175

Regression Features - Test SummaryLWAPP-AP-SW

PassedTo verify whether APjoins a WLC or notwhen both AP andWLC are in differentsubnets

AP Join processWLJ80S_lwapp_06

WCM_WEBDefectsStatusDescriptionTitleLogical ID

PassedTo verify whetherchannel 120, 124,128 are added byExtended UNII-2channels or not

Extended UNII-2Channels

WLJ80S_wcm-web_01

PassedTo verify whetherPSK key get changedor not after WLANmodifications aredone

PSK key afterWLANmodification

WLJ80S_wcm-web_02

PassedTo verify whetherAllowed power levelis AP specific or not

Allowed powerlevel

WLJ80S_wcm-web_03

PassedTo verify whetherboth CLI and GUIoutput for EAP typematched or not

EAP typementioned

WLJ80S_wcm-web_04

PassedTo verify whetherthe AntennaParameters areshown appropriatelyor not in the802.11a/n/ac radiopage

802.11a/n/ac RadioEdit page - AntennaParams

WLJ80S_wcm-web_05

PassedTo verify whetherthe AntennaParameters areshown appropriatelyor not in the802.11b/g/n radiopage

802.11b/g/n RadioEdit page - AntennaParams

WLJ80S_wcm-web_06


176

Regression Features - Test SummaryWCM_WEB

PassedTo verify whetherthe RF ChannelAssignment is shownappropriately or notin the 802.11a/n/acradio page

802.11a/n/ac RadioEdit page - RFChannelAssignment

WLJ80S_wcm-web_07

PassedTo verify whetherthe RF ChannelAssignment is shownappropriately or notin the 802.11b/g/nradio page

802.11b/g/n RadioEdit page - RFChannelAssignment

WLJ80S_wcm-web_08

WLC_Web-authDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether boththe L2 and L3re-authentication occursafter the session timeoutor not

Clients reachingSession timeout whenattached to a WLANconfigured with L2 andL3 authentication

WLJ80S_WA_01

PassedTo verify whether boththe L2 and L3re-authentication occursafter the session timeoutor not

Clients reachingSession timeout whenattached to a WLANconfigured with L2 andL3 authentication -after roaming from oneAP to an another

WLJ80S_WA_02

PassedTo verify whether thecustom web-auth pagere-appears after enteringincorrect email addressor not

Web-auth guest access,custom bundle,pass-through withemail - Windows 7Client

WLJ80S_WA_03

PassedTo verify whether thecustom web-auth pagere-appears after enteringincorrect email addressor not

Web-auth guest access,custom bundle,pass-through withemail - Apple MACBook Client

WLJ80S_WA_04

PassedTo verify whether thelogout optionworks finefor the web-auth user ornot

Web-auth bundletemplate - InternalWeb-Auth

WLJ80S_WA_05


177

Regression Features - Test SummaryWLC_Web-auth

PassedTo verify whether thelogout optionworks finefor the web-auth user ornot

Web-auth bundletemplate - ExternalWeb-Auth

WLJ80S_WA_06

PassedTo verify whether"config certificategenerate webadmin" ispresent or not in thebackup file which isuploaded

config certificategenerate webadmin -Backup file uploaded

WLJ80S_WA_07

PassedTo verify whether"config certificategenerate webadmin" ispresent or not with thebackup file which isdownloaded

config certificategenerate webadmin -Backup filedownloaded

WLJ80S_WA_08

Alarms_UIDefectsStatusDescriptionTitleLogical ID

PassedTo verify whethersorting functions worksin Unclassified RogueAP's page or not

SortingUnclassifiedRogue AP's

WLJ80S_alm-ui_02

PassedTo verify whethersorting functions worksin Malicious RogueAP's page or not

SortingMaliciousRogue AP's

WLJ80S_alm-ui_03

Client_MgmtDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether "1Hour" can be selectedor not as ReportingPeriod in Clientsummary report

Reporting Periodin Client summaryreport

WLJ80S_cl-mgnt_01


178

Regression Features - Test SummaryAlarms_UI

PassedTo verify whetherClient Traffic reportedby each Floor value &Client Traffic reportedby Sum of AP by Floorvalue matches or not

NCS Client trafficreport

WLJ80S_cl-mgnt_02

PassedTo verify whether thereis a break in Clientgraph updation afterrestart of services ornot

Client graphupdation afterservice startup

WLJ80S_cl-mgnt_03

PassedTo verify whether theAuthenticated ClientCount shown whenReported by: All andAP By Controllermatches

AuthenticatedClient Count

WLJ80S_cl-mgnt_04

MSE_InstallDefectsStatusDescriptionTitleLogical ID

PassedTo verify whetherMSE is gettingconnected to the NCSonce after the MSE isupgraded or not

Connection withNCS afterupgrading the MSE

WLJ80S_install_01

PassedTo verify whetherMSE is gettingconnected to the NCSonce after the MSE isdowngraded or not

Connection withNCS afterdowngrading theMSE

WLJ80S_install_02

PassedTo verify whether theeth0 interface iscoming up or not afterrebooting the MSE

Eth0 interface statusafter MSE reboot

WLJ80S_install_03

PassedTo verify whether theeth0 interface iscoming up or not afterupgrading the MSE

Eth0 interface statusafter MSE upgrade

WLJ80S_install_04

PassedTo verify whether theeth0 interface iscoming up or not afterdowngrading the MSE

Eth0 interface statusafter MSEdowngrade

WLJ80S_install_05


179

Regression Features - Test SummaryMSE_Install

PassedTo verify whether NCSCommunicationCredentials can bechanged by invokingsetup.sh script or not

NCSCommunicationUsername andPassword - MSEVirtual Appliance

WLJ80S_install_06

PassedTo verify whether NCSCommunicationCredentials can bechanged by invokingsetup.sh script or not

NCSCommunicationUsername andPassword - Physical3355 Series MSE

WLJ80S_install_07

NCS-MSEDefectsStatusDescriptionTitleLogical ID

PassedTo verify whetherPrime Infrastructuredisplays the MSELicense Usage Tablesummary or not

MSE License UsageTable summary -Physical 3355 MSE

WLJ80S_pi-mse_01

PassedTo verify whetherPrime Infrastructuredisplays the MSELicense Usage Tablesummary or not

MSE License UsageTable summary -MSE Virtualappliance

WLJ80S_pi-mse_02

PassedTo verify whetherMSAP Services canbe disabled from theNCS GUI or not

Physical 3355 SeriesMSE - MSAPService in NCS

WLJ80S_pi-mse_03

PassedTo verify whetherpermanent license forMSAP services isdisplayed or not

Permanent Licensefor MSAP Services- Physical 3355Series MSE

WLJ80S_pi-mse_04

PassedTo verify whetherMSAP Services canbe disabled from theNCS GUI or not

Virtual ApplianceMSE - MSAPService in NCS

WLJ80S_pi-mse_05

PassedTo verify whetherpermanent license forMSAP services isdisplayed or not

Permanent Licensefor MSAP Services- Virtual ApplianceMSE

WLJ80S_pi-mse_06


180

Regression Features - Test SummaryNCS-MSE

WLC-RRMDefectsStatusDescriptionTitleLogical ID

PassedTo check if the formatfor objectcLApDot11IfSlotId isnot interpreted wronglyin the SNMP servermessage logs

SNMP data sentfrom WLC 5508

WLJ80s_rrm_01


SNMP data sentfrom WLC 2504

WLJ80s_rrm_02


SNMP data sentfrom WLC7500/8500

WLJ80s_rrm_03


SNMP data sentfrom WLCWiSM2/vWLC

WLJ80s_rrm_04

PassedTo check the messagelog in the controller forany save error afterconfiguring any RRMdata

Message log aftersaving RRM data in5508 controller

WLJ80s_rrm_05


Message log aftersaving RRM data in7500/8500controller

WLJ80s_rrm_06


Message log aftersaving RRM data in2504 controller

WLJ80s_rrm_07


181

Regression Features - Test SummaryWLC-RRM


Message log aftersaving RRM data inWiSM2 controller

WLJ80s_rrm_08

PassedTo check if the 802.11amonitor mode can bedisabled in 5508controller afterdisabling RF group,DCA and TPC.

802.11a monitormode disable in5508 Controller

WLJ80s_rrm_09

PassedTo check if the 802.11amonitor mode can bedisabled in 7500/8500controller afterdisabling RF group,DCA and TPC.

802.11a monitormode disable in7500/8500Controller

WLJ80s_rrm_10

PassedTo check if the 802.11amonitor mode can bedisabled in 2504controller afterdisabling RF group,DCA and TPC.

802.11a monitormode disable in2504 Controller

WLJ80s_rrm_11

PassedTo check if the 802.11amonitor mode can bedisabled inWiSM2/vWLCcontroller afterdisabling RF group,DCA and TPC.

802.11a monitormode disable inWiSM2/vWLCController

WLJ80s_rrm_12

PassedTo check if theconfiguration file whichhas been uploaded afterconfiguring RF profilescan be downloaded intothe controller withoutany issues

Upload/Downloadwith RF profileconfigs in 5508WLC

WLJ80s_rrm_13


Upload/Downloadwith RF profileconfigs in7500/8500 WLC

WLJ80s_rrm_14


182



Upload/Downloadwith RF profileconfigs in 2504WLC

WLJ80s_rrm_15


Upload/Downloadwith RF profileconfigs inWiSM2/vWLC

WLJ80s_rrm_16

PassedTo check if theconfiguration guide hasa note regarding APchannel change

Checking theConfiguration guidefor note

WLJ80s_rrm_17

PassedTo check if thesimulated and realclients are able toassociate to the AP incontroller without anyproblem after couple ofHA failovers

Client Associationwith Aps in 5508Controller aftersome number of HAfailovers

WLJ80s_rrm_18


Client Associationwith Aps in7500/8500Controller aftersome number of HAfailovers

WLJ80s_rrm_19


Client Associationwith Aps in 2504Controller aftersome number of HAfailovers

WLJ80s_rrm_20

PassedTo check if the RRMAP neighbor list issynced to HA pair afterswitchover

RRM AP Neighborlist sync to HAStandby afterswitchover in 5508HA pair

WLJ80s_rrm_21


183




WLJ80s_rrm_22



WLJ80s_rrm_23



WLJ80s_rrm_24

PassedTo check if the RFprofile config which isconfigured in the WLCis present in theuploaded configurationfile

RF profile config inuploaded file from5508 controller

WLJ80s_rrm_25


RF profile config inuploaded file from2504 controller

WLJ80s_rrm_26


RF profile config inuploaded file from7500/8500controller

WLJ80s_rrm_27


RF profile config inuploaded file fromWiSM2/vWLCcontroller

WLJ80s_rrm_28

PassedTo check if thecommand for advance802.11a/b monitornoise when configuredout of range retainsafter WLC reboot

ConfiguringAdvance802.11[a|b] monitornoise out of range in5508 Controller

WLJ80s_rrm_29


184



ConfiguringAdvance802.11[a|b] monitornoise out of range in7500/8500Controller

WLJ80s_rrm_30


ConfiguringAdvance802.11[a|b] monitornoise out of range in2504 Controller

WLJ80s_rrm_31


ConfiguringAdvance802.11[a|b] monitornoise out of range inWiSM2/vWLCController

WLJ80s_rrm_32

PassedTo check if all AQ's arepresent for entirechannel list for monitormode AP joined to thecontroller

CleanAir air-qualitysummary in Apsjoined to 5508controller

WLJ80s_rrm_33


CleanAir air-qualitysummary in Apsjoined to 7500/8500controller

WLJ80s_rrm_34


CleanAir air-qualitysummary in Apsjoined to 2504controller

WLJ80s_rrm_35


CleanAir air-qualitysummary in Apsjoined toWiSM2/vWLCcontroller

WLJ80s_rrm_36

PassedTo Disable 802.11aDCA and check ifadvanced 802.11asummary shows onlythe supported channels

Disabling 802.11aDCA in WLC 5508

WLJ80s_rrm_37


185



Disabling 802.11aDCA in WLC7500/8500

WLJ80s_rrm_38


Disabling 802.11aDCA in WLC 2504

WLJ80s_rrm_39


Disabling 802.11aDCA in WLCWiSM2

WLJ80s_rrm_40


Disabling 802.11aDCA in vWLC

WLJ80s_rrm_41

PassedTo upload, donwloadand upload the configto controller and checkfor the 802.11 channelload/noise/DCAchannel configs

802.11a channelload/noise / DCAchannel listsconfigurations in theuploaded backupfile from controllerin 5508 controller

WLJ80s_rrm_42


802.11a channelload/noise / DCAchannel listsconfigurations in theuploaded backupfile from controllerin 7500/8500controller

WLJ80s_rrm_43


802.11a channelload/noise / DCAchannel listsconfigurations in theuploaded backupfile from controllerin 2504 controller

WLJ80s_rrm_44


186



802.11a channelload/noise / DCAchannel listsconfigurations in theuploaded backupfile from controllerin WiSM2controller

WLJ80s_rrm_45


802.11a channelload/noise / DCAchannel listsconfigurations in theuploaded backupfile from controllerin vWLC controller

WLJ80s_rrm_46

PassedTo check if thecongigured 802.11DCA channel listprevails after upgrade

802.11a DCAchannel list afterupgrade in 5508Controller

WLJ80s_rrm_47


802.11a DCAchannel list afterupgrade in7500/8500Controller

WLJ80s_rrm_48


802.11a DCAchannel list afterupgrade in 2504Controller

WLJ80s_rrm_49


802.11a DCAchannel list afterupgrade in WiSM2Controller

WLJ80s_rrm_50


802.11a DCAchannel list afterupgrade in vWLCController

WLJ80s_rrm_51

PassedTo check if any brandnew AP comes up withunexpected channels onit.

unexpected channelson New Aps

WLJ80s_rrm_52

PassedTo check If Rifs rxdisable doesn't remainafter 11n modedisabled/re-enabled

Rifs rx disableafter11n modedisabled/re-enabledin 5508 controller

WLJ80s_rrm_53


187



Rifs rx disableafter11n modedisabled/re-enabledin 7500/8500controller

WLJ80s_rrm_54


Rifs rx disableafter11n modedisabled/re-enabledin 2504 controller

WLJ80s_rrm_55


Rifs rx disableafter11n modedisabled/re-enabledin WiSM2controller

WLJ80s_rrm_56


Rifs rx disableafter11n modedisabled/re-enabledin vWLC controller

WLJ80s_rrm_57

PassedTo check if the wlansecurity static-wep-keysettings are restored toWLC after uploadingand downloading thesame config to theWLC

Restoring "wlansecuritystatic-wep-keyencryption" settingsto the WLC 5508

WLJ80s_rrm_58



WLJ80s_rrm_59



WLJ80s_rrm_60



WLJ80s_rrm_61


188



Restoring "wlansecuritystatic-wep-keyencryption" settingsto theWLCWiSM2

WLJ80s_rrm_62


Restoring "wlansecuritystatic-wep-keyencryption" settingsto the vWLC

WLJ80s_rrm_63

PassedTo check if all theconfigurations arerestored correctly inWLC

Restoring somesettings in the WLC5508

WLJ80s_rrm_64



WLJ80s_rrm_65



WLJ80s_rrm_66



WLJ80s_rrm_67


Restoring somesettings in the WLCWiSM2

WLJ80s_rrm_68


Restoring somesettings in thevWLC

WLJ80s_rrm_69

PassedTo check if the Invalidtimer traceback isobserved when thecontroller registers AP

INVALID TIMERwith traceback in5508 controller

WLJ80s_rrm_70


189



INVALID TIMERwith traceback in7500/8500controller

WLJ80s_rrm_71


INVALID TIMERwith traceback inWiSM2/vWLCcontroller

WLJ80s_rrm_72


INVALID TIMERwith traceback in2504 controller

WLJ80s_rrm_73

PassedTo check if themaximum number ofclients per wlan is notexceeded in controller

Maximum numberof allowed clientson aWLAN in 5508controller

WLJ80s_rrm_74


Maximum numberof allowed clientson a WLAN in7500/8500controller

WLJ80s_rrm_75


Maximum numberof allowed clientson aWLAN in 2504controller

WLJ80s_rrm_76


Maximum numberof allowed clientson a WLAN inWiSM2/vWLCcontroller

WLJ80s_rrm_77

PassedTo check if show clientdetail <Mac address>include client statistics

Show client detailMAC Address

WLJ80s_rrm_78

All AP-RadioDefectsStatusDescriptionTitleLogical ID


190

Regression Features - Test SummaryAll AP-Radio

PassedTo check if the Radioin AP1142 goes intodown state withprotocol being downafter a radio reset,profile changes, radiobring up etc

Radio reset, profilechanges, radio bringup in AP1142

WLJ80S_aprad_01



WLJ80S_aprad_02



WLJ80S_aprad_03

PassedTo check if the Radioin AP3500,3600 goesinto down state withprotocol being downafter a radio reset,profile changes , radiobring up etc

Radio reset, profilechanges, radio bringup in AP3500,3600

WLJ80S_aprad_04

PassedTo check if the Radioin AP3700 goes intodown state withprotocol being downafter a radio reset,profile changes , radiobring up etc


WLJ80S_aprad_05

PassedTo verify if themulticast traffic worksfine even after the fastroaming of the clientson a particular wlan

Multicast trafficafter fast roaming in5508 controllershaving Aps

WLJ80S_aprad_06


Multicast trafficafter fast roaming in7500/8500controllers havingAps

WLJ80S_aprad_07


191

Regression Features - Test SummaryAll AP-Radio


Multicast trafficafter fast roaming in2504/WiSM2controllers havingAps

WLJ80S_aprad_08

PassedTo verify if the clientsare able to transferdata without anyproblem and thetransmitting andreceiving on the APradio is smooth.

Transmitting andreceiving on 1142AP

WLJ80S_aprad_09


Transmitting andreceiving on3500/3600 AP's

WLJ80S_aprad_10


Transmitting andreceiving on 1262AP's

WLJ80S_aprad_11


Transmitting andreceiving on 3700AP's

WLJ80S_aprad_12

AP-DFSDefectsStatusDescriptionTitleLogical ID

PassedTo check if the APassociation to thecontroller prevails aftera DFS

AP associationafter DFS Scanevent in 5508controller

WLJ80S_dfs_01


192

Regression Features - Test SummaryAP-DFS


AP associationafter DFS Scanevent in 7500/8500controller

WLJ80S_dfs_02


AP associationafter DFS Scanevent in 2504controller

WLJ80S_dfs_03


AP associationafter DFS Scanevent inWiSM2/vWLCcontroller

WLJ80S_dfs_04

PassedTo check if the 5GHzchannel doesn't revertback to originalconfigured static channel

5GHZ channel in5508 controller

WLJ80S_dfs_05


5GHZ channel in7500/8500controller

WLJ80S_dfs_06


5GHZ channel in2504 controller

WLJ80S_dfs_07


5GHZ channel inWiSM2/vWLCcontroller

WLJ80S_dfs_08

PassedTo check if the APdoesn't go to Discoverystate after all theavailable 802.11achannels are exhaustedafter a DFS event

AP's behaviourafter all available11a channels areexhausted in 5508controller

WLJ80S_dfs_09



WLJ80S_dfs_10


193

Regression Features - Test SummaryAP-DFS



WLJ80S_dfs_11

AP RadioDefectsStatusDescriptionTitleLogical ID

PassedTo verify the clientcount in LAP withFlexconnect mode

Client count checkin AP withflexconnect mode

WLJ80S_ap-rad_01

PassedTo verify the clientcount in LAP withLocal mode

Client count checkin AP with localmode

WLJ80S_ap-rad_02

PassedTo verify the 1142 APperformance afterupgrading to 7.4MR3

1142 APfunctionality inlocal mode afterupgrading to 7.4MR3

WLJ80S_ap-rad_03

PassedTo verify the 1142 APperformance afterupgrading to 7.4MR4

1142 APfunctionality inflexconnect modeafter upgrading to7.4 MR3

WLJ80S_ap-rad_04

PassedTo verify whether APcomes with 802.11b/gradio disabled afterreload

802.11b/g radiodisabled andreboot the AP

WLJ80S_ap-rad_05

PassedTo verify the unifiedimages with clienttraffic

Unified images inAP with clienttraffic

WLJ80S_ap-rad_06

PassedTo verify the APS3500/3600 while bootup with autonomousios images

Autonomous iosimages in AP

WLJ80S_ap-rad_07

PassedTo verify the APS3500/3600 wile bootup with recovery iosimages

Recovery iosimages in AP

WLJ80S_ap-rad_08


194

Regression Features - Test SummaryAP Radio

PassedTo verify whether theradios should not resetfrequently whenstop-on-failure set

AP radioperformancewhenstop-on-failure set

WLJ80S_ap-rad_17

PassedTo verify the AP radioperformance whenclient is frequentlyassociating/disassoaciatingwith stop-on-failureset

AP radioperformancewhenclient is frequentlyassociating/disassocitingwithstop-on-failureset-WLC 5508,2504

WLJ80S_ap-rad_18


AP radioperformancewhenclient is frequentlyassociating/disassocitingwithstop-on-failureset-WLC7500,8500

WLJ80S_ap-rad_19


AP radioperformancewhenclient is frequentlyassociating/disassocitingwithstop-on-failureset-WLC WiSM2

WLJ80S_ap-rad_20

PassedTo verify the AP radioperformancewhenAPfallover betweenpri/sec withstop-on-failure set

AP radioperformancewhenAP falloverbetween pri/secwithstop-on-failureset-WLC 5508,2504

WLJ80S_ap-rad_21


AP radioperformancewhenAP falloverbetween pri/secwithstop-on-failureset-WLC 7500,8500

WLJ80S_ap-rad_22


195

Regression Features - Test SummaryAP Radio


AP radioperformancewhenAP falloverbetween pri/secwithstop-on-failureset-WLC WiSM2

WLJ80S_ap-rad_23

PassedTo verify the AP radioperformance whenfrequent clientassociation/disassociationand/or AP fallbackbetween pri/sec withstop-on-failuredisabled

AP radioperformancewhenfrequent clientass/disass and/orAP fallback whenstop-on-failuredisabled

WLJ80S_ap-rad_24

PassedTo verify the APradios operationalstatus in WLC

AP radiosoperational statusin WLC

WLJ80S_ap-rad_25

PassedTo verify the APradios operationalstatus in WLC andclient connectivity

AP radiosoperational statusinWLC and clientconnectivity

WLJ80S_ap-rad_26

WLC HADefectsStatusDescriptionTitleLogical ID

PassedTo verify whether ACLshas been syncedbetween the Active andStandby Hot WLC

ACL config syncbetween the Activeand Standby HotWLC

WLJ80S_WLCHA_01

PassedTo verify whetherclients access detailsspecified in the aclsafter switchover

Client connectivitywith aaa overridenWLAN afterswitchover-Samsung Galaxy,iPhone

WLJ80S_WLCHA_02

PassedTo verify whetherclients access detailsspecified in the aclsafter switchover

Client connectivitywith aaa overridenWLAN afterswitchover-Macbook Pro,Windows 7 JOS

WLJ80S_WLCHA_03


196

Regression Features - Test SummaryWLC HA

PassedTo verify whetherMobility Mac addressand redundancy Macaddress is showncorrectly in Active andStandby WLC

Mobility macaddress betweenActive and StandbyWLC

WLJ80S_WLCHA_04

PassedTo verify whetherMobility Mac addressand redundancy Macaddress is showncorrectly in Active andStandby WLC

Mobility macaddress betweenActive and StandbyWLC whereprimary WLC isreplaced with newWLC

WLJ80S_WLCHA_05

PassedTo verify whether HAfailover is successfulafter saving the configand powercycling theActive WLC

HA failover afterpowercycling theActive WLC

WLJ80S_WLCHA_06

PassedTo verify whether Bulkconfig sync is successfulbetween the WLCs inHA pair

Bulk config syncbetween the WLCs

WLJ80S_WLCHA_07

PassedTo verify whether runtime config has beensynced between theWLCs

Incremental configsync between theWLCs

WLJ80S_WLCHA_08

PassedTo verify whether FLSconfig has been syncedbetween WLC HA pair

Flexconnect Localswitching configsync between theWLCs

WLJ80S_WLCHA_09

PassedTo verify whether theFLS config has beenretained after HAswitchover

FLS config after HAfailover

WLJ80S_WLCHA_10

PassedTo verify whether clientserves with localswitching after WLCswitchover

Client connectivitywith FLS enabledWLAN after WLCswitchover-Samsung galaxy,iPhone

WLJ80S_WLCHA_11

PassedTo verify whether clientserves with localswitching after WLCswitchover

Client connectivitywith FLS enabledWLAN after WLCswitchover-Macbook pro,windows 7 JOS

WLJ80S_WLCHA_12


197


PassedTo verify whetherconfig upload issuccesful and all confighas been imported toHA pair

Config upload inHA pair

WLJ80S_WLCHA_13

PassedTo verify whether thereis no switchover whenthe mgmt default GWfailover is disabled andActive mgmt port isdown

Disable the mgmtdefault GW failoverand Active mgmtport down

WLJ80S_WLCHA_14

PassedTo verify whether thereis no reboot occuredwhen the mgmt defaultGW failover is disabledand Standby mgmt portis down

Disable the mgmtdefault GW failoverand Standby mgmtport down

WLJ80S_WLCHA_15

PassedTo verify whetherswitchover happenswhenmgmt default GWis enabled and Activemgmt port is down

Enable the mgmtdefault GW failoverand Active mgmtport down

WLJ80S_WLCHA_16

PassedTo verify whetherreboot of standby occurswhenmgmt default GWis enabled and Standbymgmt port is down

Enable the mgmtdefault GW failoverand Standby mgmtport down

WLJ80S_WLCHA_17

PassedTo verify whetherSNMP trap notificationis generated when thereis a WLC switchover

SNMP trapnotification in caseof WLC switchover

WLJ80S_WLCHA_18

PassedTo verify whether thereare no unknownmessages insyslog/msglog

Unknown messagesin msglog/syslog

WLJ80S_WLCHA_19

PassedTo verify whether unitof converted secondarybox should show as"Secondary"

Unit of secondarybox which isconverted

WLJ80S_WLCHA_20

PassedTo verify the HAfailover process duringsoftware download toStandby WLC

HA failover duringsoftware downloadto Standby HOTWLC with gwunreachable

WLJ80S_WLCHA_22


198


PassedTo verify the HAfailover process duringsoftware download andGW unreachable fromActive controller

HA failover duringsoftware downloadto ActiveWLCwithGW unreachable toActive

WLJ80S_WLCHA_23

PassedTo verify the HAfailover process duringsoftware download toStandby WLC and GWunreachable from bothActive and StandbyWLC

HA failover duringsoftware downloadto ActiveWLCwithGW unreachable toboth Active andStandby HOT

WLJ80S_WLCHA_24

PassedTo verify the HAfailover process duringsw download and redport down in StandbyWLC

HA failover duringSW download toActive and Standbyand red port downin Standby WLC

WLJ80S_WLCHA_25

PassedTo verify the HAfailover process duringsw download and redport down in ActiveWLC

HA failover duringSW download toActive and Standbyand red port downin Active WLC

WLJ80S_WLCHA_26

PassedTo verify the HAfailover process duringsw download and redport down in Active andStandbyWLC

HA failover duringSW download toActive and Standbyand red port downin both Active andStandby WLC

WLJ80S_WLCHA_27

PassedTo verify whether laxtiming is configurable inHA pair

Redundancylaxtimingconfigurations

WLJ80S_WLCHA_28

PassedTo verify whethermultiple switchoversbetween the WLCs areworking fine withnumber of Aps added

HA multipleswitchovers withnumber of Apsadded

WLJ80S_WLCHA_29

PassedTo verify there is nofalse switchoverbetween the HA pair

HA false switchoverWLJ80S_WLCHA_30

PassedTo verify there is nounwanted/irrelevant HArelatedmessages printedon console or syslog

Check for noirrelevant HA errormessages on syslogor console

WLJ80S_WLCHA_32


199


Backup - RestoreDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether PIbackup has been takenwhen FTP password isset upto 16 chars

PI backup with FTPpassword set as 16char - pPI

WLJ80S_BnR_01

PassedTo verify whether PIbackup has been takenwhen FTP password isset upto 16 chars

PI backup with FTPpassword set as 16char - vPI

WLJ80S_BnR_02

PassedTo verify whetherbackup of invalid filein standalone boxprints the appropriateerror message

PI restore instandalone box withinvalid backup file

WLJ80S_BnR_03

PassedTo verify whetherbackup of invalid filein HA enabled boxprints the appropriateerror message

PI restore in HAenabled box withinvalid backup file

WLJ80S_BnR_04

PassedTo verify whetherrestoring a validbackup file succeeds

PI restore with avalid backup file

WLJ80S_BnR_05

PassedTo verify theapplication backup andrestore operation issuccessful

PI applicationbackup and restore

WLJ80S_BnR_06

PassedTo verify theappliance backup andrestore operation issuccessful

PI appliance backupand restore

WLJ80S_BnR_07

PassedTo verify whetherautomatic and manualbackup are workingfine in PI applicationwithout any issues

PI applicationbackup- automaticand manual

WLJ80S_BnR_08

PassedTo verify whethertaking backupinternally by filling75% in /opt and checkthe domain mapsunder/opt/CSCOlumos/domainmaps

PI backup andchecking domainmaps

WLJ80S_BnR_09


200

Regression Features - Test SummaryBackup - Restore

PassedTo verify whethertaking backup to anexternal server byfilling 75% in /opt andcheck the domainmaps under/opt/CSCOlumos/domainmaps


WLJ80S_BnR_10

PassedTo verify whethertaking backupinternally by filling95% in /opt and checkthe domain mapsunder/opt/CSCOlumos/domainmaps


WLJ80S_BnR_11

PassedTo verify whethertaking backup to anexternal server byfilling 95% in /opt andcheck the domainmaps under/opt/CSCOlumos/domainmaps


WLJ80S_BnR_12

SystemDefectsStatusDescriptionTitleLogical ID


To verify whetherchanging thehostname/IP whenre-setup starts the PIservices completelyand works fine

PI IP/Hostnamechange uponre-setup

WLJ80S_Sys_01

PassedTo verify whetherexternal serverconfig on PI doesnotmake the servicesdown

PI external SNMPserver config

WLJ80S_Sys_02

NCS HADefectsStatusDescriptionTitleLogical ID


201

Regression Features - Test SummarySystem

PassedTo verify the PI HArelationship whenprimary and secondaryservers shutdown at thesame time and madesecondary to be up first

PI HA relationshipwhen secondaryshutdown first

WLJ80S_pi-ha_01

PassedTo verify the PI HArelationship whenprimary and secondaryservers shutdown at thesame time and madeprimary to be up first

PI HA relationshipwhen primaryshutdown first

WLJ80S_pi-ha_02

PassedTo verify whetherfailback is working finewhere failover type is setas "Manual" in case ofprimary server failuredue to hardware issue

PI failback toprimary serverwith failover set as"Manual"

WLJ80S_pi-ha_03

PassedTo verify whetherfailback is working finewhere failover type is setas "Manual" in case ofprimary server failuredue to network issue

PI failback toprimary serverwith failover set as"Manual"

WLJ80S_pi-ha_04

PassedTo verify whetherfailback is working finewhere failover type is setas "Automatic" in caseof primary server failuredue to hardware issue

PI failback toprimary serverwith failover set as"Automatic"

WLJ80S_pi-ha_05

PassedTo verify whetherfailback is working finewhere failover type is setas "Automatic" in caseof primary server failuredue to network issue

PI failback toprimary serverwith failover set as"Automatic"

WLJ80S_pi-ha_06

PassedTo verify whetherfailback to freshlyinstalled primary serveris working fine

PI failback toprimary whereprimary server isfreshly installedafter failover

WLJ80S_pi-ha_07


202

Regression Features - Test SummaryNCS HA

PassedTo verify whether PIlicense has beeninitialized in secondaryafter failover tosecondary server in caseof primary failed

Pi Licensing afterfailover tosecondary whenprimary server isfailed due to HWfailure

WLJ80S_pi-ha_08

PassedTo verify whether PIlicense has beeninitialized in secondaryafter failover tosecondary server in caseof primary failed

Pi Licensing afterfailover tosecondary whenprimary server isfailed due to NWfailure

WLJ80S_pi-ha_09

NCS Clean-AirDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether AQMinimum Index should besmaller than AQ AverageIndex in AQ Index VsTime report graph

PI AQ Index VsTime report

WLJ80S_cleanair_01

NCS LicensingDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether PIlicense is working finein PI physicalappliance

PI License worksfine

WLJ80S_lic_01

PassedTo verify whether PIlicense is working finein PI virtual appliance

PI License worksfine

WLJ80S_lic_02

MSE SoftwareDefectsStatusDescriptionTitleLogical ID


203

Regression Features - Test SummaryNCS Clean-Air

PassedTo verify whetherchange passwordwork after theautomatic reboot ofMSE

checkMSE passwordreset reflect afterreboot

WLJ80S_msesw_01

PassedTo verify whetherthe MSE servicesand health monitorstarted in 5 mints

Check the MSEservices start up in5mints

WLJ80S_msesw_02

PassedTo verify the MSEhardware test showsthe error message as"No such file ordirectory"

Check whether theMSE show the errormessage forHardware test

WLJ80S_msesw_03

PassedTo verify whetherthe location changedistance value doesnot zero for eventdefinition

check the locationchange distance valueon event notification

WLJ80S_msesw_04

CSCup21225FailedTo verify whetherMSE reachable fromPI and check NMSPstatus after upgrade

check MSE NMSPstatus after upgrade

WLJ80S_msesw_05

CSCuo56629FailedTo verify whetherMSE failover andfailback works asexpected whenshutdown MSE's

MSE Faibackfunctionality whensecondary MSEcomes up first aftershutdownof bothMSE

WLJ80S_msesw_06

PassedTo verify whetherthe error messagetriggered to syslogwhen process triggerthe error

check MSE errormessage on syslogonly error messagetriggered on theprocess

WLJ80S_msesw_08

CSCup93585FailedTo verify whetherthe Context AwareNotifications forMultiple eventDefinitions created

Context AwareNotificationsMultiple eventDefinitions usingsyslog

WLJ80S_msesw_09

PassedTo verify whetherthe MSE displaysmessage for everyfew seconds afterupgrade

Check MSE displayany error afterupgrade

WLJ80S_msesw_10


204

Regression Features - Test SummaryMSE Software

WLC LANDefectsStatusDescriptionTitleLogical ID

PassedTo verify whetherenable and disable ofthe controller LAGshows any errormessage

Enable and disablethe controller LAGon controller

WLJ80S_lan_02

PassedTo verify whether thecontroller send LAGdown and upmessageto the syslog serversuccessfully

check controllersend the syslogmessagewhen LAGport up and down

WLJ80S_lan_03

PassedTo verify whether theaccess point getsdisconnected duringdownloading wlcimage from the TFTP

check the accesspoint disconnectedduring controllerimage download

WLJ80S_lan_04

PassedTo verify whether theGARP request are notforward to AP andclient is successful

check the GARPrequest are forwardto AP and client

WLJ80S_lan_05

WLC SNMPDefectsStatusDescriptionTitleLogical ID

PassedTo verify whethercan install the WLCMIB file into theSNMP managersuccessfully

install WLC MIBfile on SNMPmanager

WLJ80S_snmp_01

PassedTo verify the SNMPcommunity ip andmask can beconfigured as 0.0.0.0

Check whether canadd the ip and maskas 0.0.0.0 on WLCSNMP community

WLJ80S_snmp_02

PassedTo verify whether theSNMP backupconfigurationrestored correctly onthe new wlc image

check the restore ofWLC SNMPconfiguration on thenew WLC image

WLJ80S_snmp_03


205

Regression Features - Test SummaryWLC LAN

PassedTo verify whetherwireless controllerdoes not return anyinvalid Tx rate s

check the controllerMIB returns anyinvalid Tx rate

WLJ80S_snmp_04

PassedTo verify the whetherthe deny creation ofdefault SNMP entriesworks as expected

Restriction forchanging accesslevel on the defaultSNMP public

WLJ80S_snmp_05

MapsDefectsStatusDescriptionTitleLogical ID

PassedTo verify the NCSdoesn't delete the.PNG and .GIF filesafter back completed.

check whether thebackup of NCS holdthe .PNG and .GIFfile under domainmaps directory

WLJ80S_maps_01

PassedTo verify the accesspoint protocol settingon NCS floor viewchanges properly

Check whether theNCSmaps floor viewaccess point protocolsetting changes asexpected

WLJ80S_maps_02

PassedTo verify the clientfilter setting on NCSfloor view changesproperly when saved

Check whether theNCSmaps floor viewclient filter settingchanges as expected

WLJ80S_maps_03

PassedTo verify NCS airquality heat mapshows the while noisearound after disablingAP radio

check whetherdisabling the APradio cause noise inNCS heat maps

WLJ80S_maps_04

PassedTo verify the NCSfloor planning modeshows the heat mapoffset

Checkwhether centerof the heat map isshifted from AP inNCS planning mode

WLJ80S_maps_05

PassedTo verify the APstatus on NCSbuilding view changeswhen disable APadministratively

Check whether theAP status on the NCSbuilding view afterdisable it on WLC

WLJ80S_maps_06


206

Regression Features - Test SummaryMaps

PassedTo verify the APstatus on NCS floorview changes whendisable APadministratively

Check whether theAP status on the NCSfloor view afterdisable it on WLC

WLJ80S_maps_07

PassedTo verify the loadingof heat maps asexpected

check whether theheat maps loadslowly even disablethe dynamic heatmaps on Maps

WLJ80S_maps_08

WLC-MobilityDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether theDTLS handshake issuccessful betweenmobility anchor andmobility controller

Check the DTLShandshake betweenmobility anchor andmobility controller

WLJ80S_mob_01

PassedTo check if manycontrollers can beadded as Mobilitypeers , removed etc

Check mobilitypeers can beremoved and nocontroller should beadded as mobilityanchors

WLJ80S_mob_02

PassedTo verify whether themobility peer with hashvalue as none is createdsuccessfully

Create WLCmobility peer withhash value none

WLJ80S_mob_03

PassedTo verify whether theWLC maximummobility groupmember 72 addedsuccessfully

Add the WLCmaximum mobilitygroup member as 72

WLJ80S_mob_04

LocationDefectsStatusDescriptionTitleLogical ID


207

Regression Features - Test SummaryWLC-Mobility

PassedTo verify the upgradeof WLC showsadditional defaultconfig when take theconfig backup to tftp

Check whether theadditional configdisplays afterupgrade the WLC

WLJ80S_WLCLO_01

PassedTo verify the defaultaggregate proberequest on wlan as500msec when noMSE connected

Check whetherdefault aggregateprobe request onwlan as 500msecwhen client loadbalancing is notenabled and no MSEconnected

WLJ80S_WLCLO_02

PassedTo verify the defaultaggregate proberequest on wlan as200msec when MSEconnected

Check whetherdefault aggregateprobe request onwlan as 200msecwhen client loadbalancing is notenabled and MSEconnected

WLJ80S_WLCLO_03

PassedTo verify the locationtracking does notshow the invalid rssi-128

Check whether thelocation trackingworking as expected

WLJ80S_WLCLO_04

WLC MulticastDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether L2multicast status asexpected whendownload and uploadthe config

check the L2multicaststatus for uploadedand download configfile

WLJ80S_MU_01

PassedTo verify whether themulticast on WLANworks as expectedafter the upgradesuccessfully

check the disabledmulticast on WLANwith flexconnect localswitching enabledstatus after upgrade

WLJ80S_MU_02


208

Regression Features - Test SummaryWLC Multicast

AP-RegulatoryDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether theallowed frequencyrange works asexpected successfully

Check allowedfrequency rangefor the japanregulatory domain

WLJ80S_apreg_01

PassedTo verify whether theJP world wide modemarked inbeacon/proberesponse instead of J4successfully

JP World widemarking inBeacon/proberesponse

WLJ80S_apreg_02

PassedTo verify the AP3502radio interfaceoperation status andbeaconing properly

Checkwhether theAP3502 radiointerface operationstatus working asexpected

WLJ80S_apreg_03

WLC DHCPDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether theDHCP assignmentrequired is retained onWLAN after WLCreboot

check the DHCPassignmentrequired is retainedon WLAN

WLJ80S_dhcp_02

PassedTo verify whether theDHCP assignmentrequired is retained onWLAN after WLCreboot with LAGdisabled

check the DHCPassignmentrequired is retainedon WLAN withLAG disabled

WLJ80S_dhcp_03

WLC GuestaccessDefectsStatusDescriptionTitleLogical ID


209

Regression Features - Test SummaryAP-Regulatory

PassedTo verify whether theWLC guest useraccount expired onspecified datesuccessfully

Check the WLCguest user accountexpiry

WLJ80S_GA_01

PassedTo verify whetherWLC logs gets errormessage for maximumallowed loginsuccessfully

Check the wlc getserror log formaximum allowedlogin for the guestaccount

WLJ80S_GA_02

PassedTo verify whether wlcgets error log for cliententry deletionsuccessfully

Check the wlc getserror log for cliententry deletion

WLJ80S_GA_03

PassedTo verify whether wlcgets error log for onlyconfigured useraccount

Check the wlc getserror log for theconfigured useraccount

WLJ80S_GA_04

WLC NTPDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether thecontrollersuccessfullysynchronize withNTP after WLCreboot

Check the ControllerNTP synchronizationafter reboot

WLJ80S_ntp_01

PassedTo verify whether thecontroller uses thecorrect port numberfor NTP

Check the controlleruses assigned NTPport number for bothsource and destinationport number

WLJ80S_ntp_02

CAPWAP-AP-SWDefectsStatusDescriptionTitleLogical ID


210

Regression Features - Test SummaryWLC NTP

PassedTo verify whether theAP name in the APjoin statistics and inthe AP summary aresame in the 2504controller CLI

Check the joinedAP's name in thecontroller arecorrect

WLJ80S_capwap-sw_01

PassedTo verify whether theAP name in the APjoin statistics and inthe AP summary aresame in the 2504controller GUI

Check the joinedAP's name in thecontroller arecorrect

WLJ80S_capwap-sw_02

PassedTo verify whether theAP is joined withstatically configuredcontroller ip addressby using env_var

CheckAP joined tothe staticallyconfiguredcontroller ipaddress

WLJ80S_capwap-sw_03

CSCup82047FailedTo verify whether theSyslog level for thelightweight AP iaconfiguredsuccessfully

Configure theSyslog level for theLightweight AP

WLJ80S_capwap-sw_04

PassedTo verify whether theinterface isconfigured and itsavailable afterupgrading the imagein the 5508 controller

Configure andcheck the interfaceavailability in thecontroller

WLJ80S_capwap-sw_05

PassedTo verify whether theinterface isconfigured and itsavailable afterupgrading the imagein the 8500 controller

Configure andcheck the interfaceavailability in thecontroller

WLJ80S_capwap-sw_06

PassedTo verify whether theflexconnect APmaintains itsconfigured nameafter joining with the5508 controller.

Check flexconnectAP maintains itsconfigured nameafter joining withthe controller

WLJ80S_capwap-sw_07

PassedTo verify whether theflexconnect APmaintains itsconfigured nameafter joining with the8500 controller.

Check flexconnectAP maintains itsconfigured nameafter joining withthe controller

WLJ80S_capwap-sw_08


211

Regression Features - Test SummaryCAPWAP-AP-SW

PassedTo verify whether theAP disassociationalarm is triggered inPI only when APgets disjoined fromthe controller

Check APdisassociationalarm in PI

WLJ80S_capwap-sw_09

PassedTo verify whether theAP disassociationalarm is triggered invirtual PI only whenAP gets disjoinedfrom the controller

Check APdisassociationalarm in virtual PI

WLJ80S_capwap-sw_10

PassedTo verify whether theAP gets imagescorrectly whenmultiple images areupgraded in the 5508controller GUIrepeatedly withoutrebooting

Check AP getsimage correctlyfrom the controller

WLJ80S_capwap-sw_11

PassedTo verify whether theAP gets imagescorrectly whenmultiple images areupgraded in the 8500controller GUIrepeatedly withoutrebooting

Check AP getsimage correctlyfrom the controller

WLJ80S_capwap-sw_12

AP-capwapDefectsStatusDescriptionTitleLogical ID

PassedTo verify whetherthe CAPWAP clienttimers is shown in5508 controller

Check the CAPWAPclient timers : WLC5508

WLJ80S_capwap_01

PassedTo verify whetherthe CAPWAP clienttimers is shown in8500 controller

Check the CAPWAPclient timers : WLC8500

WLJ80S_capwap_02

PassedTo verify whetherthe AP's are joinedwith the controllersuccessfully

Check Ap's are joinedwith controller

WLJ80S_capwap_03


212

Regression Features - Test SummaryAP-capwap

PassedTo verify whetherthe TX power levelof the LightweightAP is configuredfrom the 5508controller GUI

Configure the TXpower level for theAP in the 5508controller via GUI

WLJ80S_capwap_05

PassedTo verify whetherthe TX power levelof the LightweightAP is configuredfrom the 5508controller CLI

Configure the TXpower level for theAP in the 5508controller via CLI

WLJ80S_capwap_06

PassedTo verify whetherthe AP is joined withthe controller afterenabling DFS.

Check the APassociation with thecontroller by enablingDFS

WLJ80S_capwap_07

PassedTo verify whetherthe AP joined withthe controller whenthey two are indifferent VLAN andno proxy arp.

Check the APassociation with thecontroller bydisabling proxy arp

WLJ80S_capwap_08

WLC-LicenseDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether thelicense priority isconfigured from wlc5508 CLI

Configure the priorityfor licenses in wlc5508 CLI

WLJ80S_lic_01

PassedTo verify whether thelicense priority isconfigured fromvirtual wlc CLI

Configure the priorityfor licenses in virtualwlc CLI

WLJ80S_lic_02

PassedTo verify whether thelicense priority isconfigured from wlc5508 GUI

Configure the priorityfor licenses in wlc5508 GUI

WLJ80S_lic_03

PassedTo verify whether thelicense priority isconfigured fromvirtual wlc GUI

Configure the priorityfor licenses in virtualwlc GUI

WLJ80S_lic_04


213

Regression Features - Test SummaryWLC-License

PassedTo check whether thelicenses having themaximum ap'ssupported count asmentioned in thecontroller - 5508 CLI

Check the supportedAP count in thelicenses in 5508controller CLI

WLJ80S_lic_05

PassedTo check whether thelicenses having themaximum ap'ssupported count asmentioned in thecontroller - virtualCLI

Check the supportedAP count in thelicenses in virtualcontroller CLI

WLJ80S_lic_06

PassedTo check whether thelicenses having themaximum ap'ssupported count asmentioned in thecontroller - 5508 GUI

Check the supportedAP count in thelicenses in 5508controller GUI

WLJ80S_lic_07

PassedTo check whether thelicenses having themaximum ap'ssupported count asmentioned in thecontroller - virtualGUI

Check the supportedAP count in thelicenses in virtualcontroller GUI

WLJ80S_lic_08

PassedTo verify whether thepermanent baselicense is removedfrom the controllersuccessfully viacontroller CLI.

Check the permanentbase license removalfrom the controller

WLJ80S_lic_10

PassedTo verify whether thepermanent baselicense is removedfrom the controllersuccessfully viacontroller GUI.

Check the permanentbase license removalfrom the controller

WLJ80S_lic_11

PassedTo verify whetherafter removinglicenses also HA pairis enabled between5508 controllers.

WLC5508: CheckHApair is enabled afterremoving all licenses

WLJ80S_lic_12


214

Regression Features - Test SummaryWLC-License

PassedTo verify whetherafter removinglicenses also HA pairis enabled between8500 controllers.

WLC8500: CheckHApair is enabled afterremoving all licenses

WLJ80S_lic_13

PassedTo verify whether HArole change is donebetween 5508controllers

WLC 5508: configureHA between thecontrollers and make arole change

WLJ80S_lic_14

PassedTo verify whether HArole change is donebetween 8500controllers

WLC 8500: configureHA between thecontrollers and make arole change

WLJ80S_lic_15

PassedTo check withoutaccepting end userlicense agreement, thebase license isremoved from the5508 controller.

Check the removal ofbase license withoutEULA.

WLJ80S_lic_16

PassedTo check withoutaccepting end userlicense agreement, thebase license isremoved from thevirtual controller.

Check the removal ofbase license withoutEULA.

WLJ80S_lic_17

PassedTo verify whether thedeleted evaluationlicense is present afterrebooting thecontroller

Check the evaluationlicense removal fromthe controller

WLJ80S_lic_20

AP-GUIDefectsStatusDescriptionTitleLogical ID

PassedTo verify whetherthe autonomous appower level forradio0 is configuredvia GUI

Configure powerlevel of radio0 inAutonomous APGUI

WLJ80S_apgui_01

PassedTo verify whetherthe autonomous appower level forradio0 is configuredvia CLI

Configure powerlevel of radio0 inAutonomousAPCLI

WLJ80S_apgui_02


215

Regression Features - Test SummaryAP-GUI

PassedTo verify whetherthe autonomous appower level forradio1 is configuredvia GUI

Configure powerlevel of radio1 inAutonomous APGUI

WLJ80S_apgui_03

PassedTo verify whetherthe autonomous appower level forradio1 is configuredvia CLI

Configure powerlevel of radio1 inAutonomousAPCLI

WLJ80S_apgui_04

PassedTo verify whetherthe autonomous apMCS rate for radio0is configured viaGUI

Configure MCS ratefor radio0 inAutonomous APGUI

WLJ80S_apgui_05

PassedTo verify whetherthe autonomous apMCS rate for radio0is configured viaCLI

Configure MCS ratefor radio0 inAutonomousAPCLI

WLJ80S_apgui_06

PassedTo verify whetherthe autonomous apMCS rate for radio1is configured viaGUI

Configure MCS ratefor radio1 inAutonomous APGUI

WLJ80S_apgui_07

PassedTo verify whetherthe autonomous apMCS rate for radio1is configured viaCLI

Configure MCS ratefor radio1 inAutonomousAPCLI

WLJ80S_apgui_08

PassedTo verify whetherthe VLAN isconfigured and ableto create openauthentication SSIDin that VLAN andclient can able toassociate by usingthat SSID.

Configure an VLANand associate theclient inAutonomousAP

WLJ80S_apgui_09


216


PassedTo verify whetherthe VLAN isconfigured and ableto create openauthentication SSIDin that VLAN andclient can able toassociate by usingthat SSID inAutonomous APCLI.

Configure an VLANand associate theclient inAutonomousAP CLI

WLJ80S_apgui_10

PassedTo verify whetherthe RADIUS serveris configured andable to authenticatethe client inautonomous ap.

Configure RADIUSserver in autonomousAP

WLJ80S_apgui_11

PassedTo verify whetherthe SSID with openauthentication isconfigured inautonomousAPGUI

Configure Openauthentication SSIDin Autonomous APGUI

WLJ80S_apgui_12

PassedTo verify whetherthe SSID with openauthentication isconfigured inautonomousAPCLI

Configure Openauthentication SSIDin Autonomous APCLI

WLJ80S_apgui_13

PassedTo verify whetherthe SSID with WEPencryption isconfigured and ableto associate with theclient in AP GUI

Configure an SSIDwith WEPEncryption in APGUI

WLJ80S_apgui_14

PassedTo verify whetherthe SSID with WEPencryption isconfigured and ableto associate with theclient in AP CLI

Configure an SSIDwith WEPEncryption in APCLI

WLJ80S_apgui_15

PassedTo verify whetherthe SSID with WPApre share key isconfigured and ableto associate with theclient in AP CLI

Configure an SSIDwith WPA Pre sharekey in AP CLI

WLJ80S_apgui_16


217


PassedTo verify whetherthe SSID with WPApre share key isconfigured and ableto associate with theclient in AP GUI

Configure an SSIDwith WPA Pre sharekey in AP GUI

WLJ80S_apgui_17

Alarm-ServerDefectsStatusDescriptionTitleLogical ID

PassedTo verify whetherthe AP rebootreason alarm istriggered with theconfigured severitylevel in PI

Severity level ofAP reboot reasonin PI

WLJ80S_alm_svr_01

PassedTo verify whetherthe AP rebootreason alarm istriggered with theconfigured severitylevel in virtual PI

Severity level ofAP reboot reasonin virtual PI

WLJ80S_alm_svr_02

PassedTo verify whetherthe AP associationwith controlleralarm is triggeredsuccessfully in PI

AP associationalarm in PI

WLJ80S_alm_svr_03

PassedTo verify whetherthe AP associationwith controlleralarm is triggeredsuccessfully invirtual PI

AP associationalarm in virtual PI

WLJ80S_alm_svr_04

PassedTo verify whetherthe mail server isconfigured andemail notification issent when rogue apalarm is triggered inPI

Email notificationfor Rogue AP in PI

WLJ80S_alm_svr_05


218

Regression Features - Test SummaryAlarm-Server

PassedTo verify whetherthe mail server isconfigured andemail notification issent when rogue apalarm is triggered invirtual PI

Email notificationfor Rogue AP invirtual PI

WLJ80S_alm_svr_06

PassedTo verify whetherthe Appliancepower supplyfailure alarm istriggered in PI

Appliance powersupply failurealarm in PI

WLJ80S_alm_svr_07

PassedTo verify whetherthe Appliancepower supplyfailure alarm istriggered in virtualPI

Appliance powersupply failurealarm in virtual PI

WLJ80S_alm_svr_08

PassedTo Verify whethernotification receiveris configuredsuccessfully in PIand able to get trapsfrom PI

ConfigureNotificationReceiver in PI andsend traps

WLJ80S_alm_svr_09

PassedTo Verify whethernotification receiveris configuredsuccessfully invirtual PI and ableto get traps fromvirtual PI

ConfigureNotificationReceiver in virtualPI and send traps

WLJ80S_alm_svr_10

Reports-WirelessDefectsStatusDescriptionTitleLogical ID

PassedTo verify the whetherthe report for rogue apcount summary isgenerated in PI

Report for Rogue APcount summary in PI

WLJ80S_RW_01

PassedTo verify the whetherthe report for rogue apcount summary isgenerated in virtual PI

Report for Rogue APcount summary invirtual PI

WLJ80S_RW_02


219

Regression Features - Test SummaryReports-Wireless

PassedTo verify the whetherthe report for RogueAP's is generated inPI

Report for RogueAP'sin PI

WLJ80S_RW_03

PassedTo verify the whetherthe report for RogueAP's is generated invirtual PI

Report for RogueAP'sin virtual PI

WLJ80S_RW_04

PassedTo verify the whetherthe report for Clienttraffic is generated inPI

Report for ClientTraffic in PI

WLJ80S_RW_05

PassedTo verify the whetherthe report for Clienttraffic is generated invirtual PI

Report for ClientTraffic in virtual PI

WLJ80S_RW_06

PassedTo verify the whetherthe report for Clientsummary is generatedin virtual PI

Report for Clientsummary in PI

WLJ80S_RW_07

PassedTo verify the whetherthe report for Clientsummary is generatedin virtual PI

Report for Clientsummary in virtual PI

WLJ80S_RW_08

WLC-TFTPDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether theHigh availability isconfigured andrunning in WLC5508.

Configure HighAvailability -WLC5508

WLJ80S_tftp_01

PassedTo verify whether theprimary AP bundleimage is downloadedto the associated AP'sin wlc 5508 afterimage upgradationwas done.

Upgrade image inWLC-5508

WLJ80S_tftp_02


220

Regression Features - Test SummaryWLC-TFTP



WLJ80S_tftp_03



WLJ80S_tftp_04



WLJ80S_tftp_05



WLJ80S_tftp_06

PassedTo verify whether therunning configurationfile is uploaded fromthe WLC 5508 to thetftp server

RunningConfiguration fileupload - WLC5508

WLJ80S_tftp_07



WLJ80S_tftp_08



WLJ80S_tftp_09

Prime-UIDefectsStatusDescriptionTitleLogical ID


221

Regression Features - Test SummaryPrime-UI

PassedTo verify the change ofPI theme in chromebrowser

Change the theme ofPI using Chromebrowser

WLJ80S_prime_01

PassedTo verify the change ofPI theme in Firefoxbrowser

Change the theme ofPI using Firefoxbrowser

WLJ80S_prime_02

PassedTo verify the change ofPI theme in IE browser

Change the theme ofPI using IE browser

WLJ80S_prime_03

PassedTo verify the change ofvirtual PI theme inchrome browser

Change the theme ofvirtual PI usingChrome browser

WLJ80S_prime_04

PassedTo verify the change ofvirtual PI theme inFirefox browser

Change the theme ofvirtual PI usingFirefox browser

WLJ80S_prime_05

PassedTo verify the change ofvirtual PI theme in IEbrowser

Change the theme ofvirtual PI using IEbrowser

WLJ80S_prime_06

PassedTo verify the details ofclients and users in PIare shown by chromebrowser

Check the PI clientsand users usingChrome browser

WLJ80S_prime_07

PassedTo verify the details ofclients and users in PIare shown by Firefoxbrowser

Check the PI clientsand users usingFirefox browser

WLJ80S_prime_08

PassedTo verify the details ofclients and users in PIare shown by IE browser

Check the PI clientsand users using IEbrowser

WLJ80S_prime_09

PassedTo verify the details ofclients and users invirtual PI are shown bychrome browser

Check the virtual PIclients and usersusing Chromebrowser

WLJ80S_prime_10

PassedTo verify the details ofclients and users invirtual PI are shown byFirefox browser

Check the virtual PIclients and usersusing Firefox browser

WLJ80S_prime_11

PassedTo verify the details ofclients and users invirtual PI are shown byIE browser

Check the virtual PIclients and usersusing IE browser

WLJ80S_prime_12


222

Regression Features - Test SummaryPrime-UI

AdminDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether theseverity count ismatched with thespecified count in thePI

Severity count in PIWLJ80S_admin_01

PassedTo verify whether theseverity count ismatched with thespecified count in thevirtual PI

Severity count inVirtual PI

WLJ80S_admin_02

PassedTo verify whether theFTP server isconfigured in PI

Add FTP server invirtual PI

WLJ80S_admin_03

PassedTo verify whether theFTP server isconfigured in virtual PI

Add FTP server inPI

WLJ80S_admin_04

PassedTo verify whether theFTP server usercredentials are updatedand able to access theserver from PI

Update the FTPserver credentials inPI

WLJ80S_admin_05

PassedTo verify whether theFTP server usercredentials are updatedand able to access theserver from virtual PI

Update the FTPserver credentials invirtual PI

WLJ80S_admin_06

NCS-UpgradeDefectsStatusDescriptionTitleLogical ID

PassedTo configure localrepository from PI CLI

Creating a Localrepository using PICLI

WLJ80S_upg_01

PassedTo configure a remoterepository from PI CLI

Creating a Remoterepository using PICLI

WLJ80S_upg_02

PassedTo view the configuredrepository from PI CLI

View the repositoryusing PI CLI

WLJ80S_upg_03


223

Regression Features - Test SummaryAdmin

PassedTo verify applicationbackup is taken for PIfrom CLI

Taking applicationbackup using PI CLI

WLJ80S_upg_04

PassedTo verify appliancebackup is taken for PIfrom CLI

Taking appliancebackup using PI CLI

WLJ80S_upg_05

PassedTo verify automaticapplication backup istaken for PI fromGUI

Scheduling automaticapplication backupusing PI GUI

WLJ80S_upg_06

PassedTo verify repository isconfigured from PIGUI

Create Repositoryusing PI GUI

WLJ80S_upg_07

PassedTo verify applicationbackup is taken for PIfrom GUI

Taking applicationbackup using PI GUI

WLJ80S_upg_08

PassedTo verify the history ofthe PI backup

View backupinformation using PICLI

WLJ80S_upg_09

PassedTo check the status ofthe PI

View the PI statusWLJ80S_upg_10

PassedTo verify whether thePI is stoppedsuccessfully.

Stop the PI serverWLJ80S_upg_11

PassedTo verify whether thePI is upgradedsuccessfully

Upgrading the PIWLJ80S_upg_12

PassedTo verify whether thePI is startedsuccessfully

Start the PI serverWLJ80S_upg_13

PassedTo verify whether theapplication is restoredcorrectly in the PI

Restore theapplication to the PIserver

WLJ80S_upg_14

PassedTo verify whether theappliance is restoredcorrectly in the PI

Restore the applianceto the PI server

WLJ80S_upg_15

PassedTo configure a switchin PI and changing theseverity level forswitch down alarm

Add a switch andseverity level in PI

WLJ80S_upg_16

PassedTo verifying the alarmin PI by bringing downthe switch.

Check switch downalarm in PI

WLJ80S_upg_17


224

Regression Features - Test SummaryNCS-Upgrade

PassedTo configure a switchin virtual PI andchanging the severitylevel for switch downalarm

Add a switch andseverity level inVirtual PI

WLJ80S_upg_18

PassedTo verifying the alarmin virtual PI bybringing down theswitch.

Check switch downalarm in virtual PI

WLJ80S_upg_19

ReportingDefectsStatusDescriptionTitleLogical ID

PassedTo verify whether theRun button isworking on ReportLaunch pad in PI

Run button in PIReport launch pad

WLJ80S_rep_01

PassedTo verify whether theSave button isworking on ReportLaunch pad in PI

Save button in PIReport launch pad

WLJ80S_rep_02

PassedTo verify whether theRun button isworking on ReportLaunch pad in virtualPI

Run button in virtualPI Report launch pad

WLJ80S_rep_03

PassedTo verify whether theSave button isworking on ReportLaunch pad in virtualPI

Save button in virtualPI Report launch pad

WLJ80S_rep_04

AAADefectsStatusDescriptionTitleLogical ID

PassedTo verify the accesspoint configurationin PI GUI

Configure an accesspoint in PI

WLJ80S_aaa_01


225

Regression Features - Test SummaryReporting

PassedTo verify the accesspoint parameters(name,mode, adminstatus, etc) are ableto change when PIis integrated withACS server

Change the accesspoint parameters inPI

WLJ80S_aaa_02

PassedTo verify the accesspoint configurationin virtual PI GUI

Configure an accesspoint in virtual PI

WLJ80S_aaa_03

PassedTo verify the accesspoint parameters(name,mode, adminstatus, etc) are ableto change whenvirtual PI isintegratedwithACSserver

Change the accesspoint parameters invirtual PI

WLJ80S_aaa_04

AP-HREAPDefectsStatusDescriptionTitleLogical ID

PassedTo verify if clientconnection failedafter WLC failover

Client connection failsafter WLC failover

WLJ80S_hreap_01

PassedTo check the creationof Flex group

Flex Connect GroupCreation

WLJ80S_hreap_02

PassedTo connect flexconnect group withwlan to vlan mapping

Flex Connect groupwith wlan to vlanmapping

WLJ80S_hreap_03

PassedTo verify the'station-role rootfallback shutdown'feature in capwap AP

station-role rootfallback shutdown forcapwap AP

WLJ80S_hreap_04

PassedTo verify theweb-auth connectionin flex connect set up

web-auth with flexconnect AP

WLJ80S_hreap_05

PassedCheck whether onebridge-group ID isassigned to singlesub-interfaces inH-reap

Verification of bridgegroup id with singleinterface

WLJ80S_hreap_06


226

Regression Features - Test SummaryAP-HREAP

PassedCheckwhether SSIDsare stoppedbeaconing with FlexConnect LocalSwitching enabled

Client connectivitywith Flex ConnectLocal switching

WLJ80S_hreap_07

PassedTo verify whetherP2P blocking actionworks or not in aWLAN whileassociating 2 clientsto this WLAN in asingle AP.

Checking P2PBlocking action in aWLAN

WLJ80S_hreap_08

WLC-WebDefectsStatusDescriptionTitleLogical ID

PassedTo verify the Apgroup name & status

AP groupNamewith14 characters

WLJ80S_web_01

PassedTo verify the Apgroup name & status

AP group name &status verification

WLJ80S_web_02

PassedTo verify the antennaselection (A)

Antenna selectiona-antenna (useantenna A)

WLJ80S_web_03

PassedTo verify the antennaselection (A &B)

Antenna selectionab-antenna (useantennas A & B)

WLJ80S_web_04

PassedTo verify the antennaselection (A &B &C)

Antenna selectionab-antenna (useantennas A & B &C

WLJ80S_web_05

PassedTo verify the antennaselection (A & B&C& D)

Antenna selectionab-antenna (useantennas A & B&C& D

WLJ80S_web_06

PassedTo verify the status ofrifs rx

Status of rifs rx afterdisbale/Re enable

WLJ80S_web_07


227

Regression Features - Test SummaryWLC-Web

PassedTo check whetherclient gets ip frommapped vlan or notwhen it gets movedbetween differentWLANS withdifferent securitytypes.

Moving a clientbetween differentWLANs with AAAoverride enabled

WLJ80S_web_09

Autonomous_APsDefectsStatusDescriptionTitleLogical ID

PassedTo verify whetherrefresh fromnetwork fails whenAutonomous AP ispresent on the floor

Refresh from networkfails whenAutonomous AP ispresent on the floor

WLJ80S_AAP_02

PassedTo verify Aiosimage forAP3G1/AP3G2 getsdownload

Unable to downloadaIOS image forAP3G1/AP3G2 imageFamily

WLJ80S_AAP_03



WLJ80S_AAP_04



WLJ80S_AAP_05



WLJ80S_AAP_06

ConfigDefectsStatusDescriptionTitleLogical ID

PassedTo verify "applicationreset-config NCS"functions properly

"applicationreset-config NCS"not doing anything

WLJ80S_config_01


228

Regression Features - Test SummaryAutonomous_APs

PassedCheck whether servicescan be started withoutany issues after back upconfig restored

Restoring the NCSDatabase

WLJ80S_config_02

PassedCheck whether servicescan be started withoutany issues after back upconfig restored

Restoring the NCSDatabase in a HighAvailabilityEnvironment

WLJ80S_config_03

WLC-WlanDefectsStatusDescriptionTitleLogical ID

PassedTo verify the clientsconnectivity withradio policy a/b/g

Voice clientsconnectivity withDot11 b/g radios

WLJ80S_wlan_02

PassedTo verify the clientsconnectivity withradio policy a

Voice clientsconnectivity withDot11 a radio

WLJ80S_wlan_03

Config-WirelessDefectsStatusDescriptionTitleLogical ID

PassedCheck th PI auditreport after the failedWLC refresh

Audit from PI withoffice extend AP

WLJ80S_cfg-wl_01

PassedTo verify copy andreplace AP functionworks

Copy And ReplaceAP function doesnot work

WLJ80S_cfg-wl_02

PassedCheck the auditmismatch warningreport on NCS forthe AP slot

Audit report onNCSfor AP

WLJ80S_cfg-wl_03

PassedCheck the auditmismatch warningreport on NCS forthe AP slot

Audit report onNCSfor AP

WLJ80S_cfg-wl_04


229

Regression Features - Test SummaryWLC-Wlan

PassedCheck theAutonomous APimage downloadedfrom server by FTPprotocol from PI

AP image FTPdownload in GUI

WLJ80S_cfg-wl_05

PassedCheck theAutonomous APimage downloadedfrom server byTFTP protocol fromPI

AP image TFTPdownload in GUI

WLJ80S_cfg-wl_06

PassedCheck theapplication of APGroup template toWLC

WCS apply APGroup template toWLC

WLJ80S_cfg-wl_11

PassedCheck theapplication of APGroup template toWLC group

WCS apply APGroup template toWLC group

WLJ80S_cfg-wl_12

PassedTo verify whetherconfiguring AP FastHeartbeat causesaudit mismatchstatus

ConfiguringAPFastHeartbeat causesAudit Mismatchstatus

WLJ80S_cfg-wl_13

SR/CFD

SR/CFD Test cases

CFD Test Cases


PassedTo check whether theclient is able to associatewith flex connect localswitching WLAN

Associate the clientto flex connect localswitching WLAN

WLJ80S_acap_01

PassedTo verify whether or notthe ACL rule'sdirections are changedafter config upload anddownload

ACLConfigurationin WLC GUI

WLJ80S_acl_01


230

Regression Features - Test SummarySR/CFD

PassedTo verify whether or notthe ACL rule'sdirections are changedafter config upload anddownload

ACLConfigurationin WLC CLI

WLJ80S_acl_02

PassedTo verify whether anyAP reloads or errorwhen associating clientunder the high trafficcondition

Check the frequentreload of AP underhigh throughputcondition.

WLJ80S_alap_01

PassedTo check the status ofthe clients after theirassociation with theWLC

Check the status ofthe clients afterassociation with theWLC

WLJ80S_alap_02

PassedTo check if cleanair isable to reportinterference

Cleanair unable toreport interference

WLJ80S_apcl_01

PassedTo configure and checkthe Bridge groupspanning treeconfiguration in ap andadd sub interface

CheckBridge groupspanning treeconfiguration in AP

WLJ80S_apcli_01

PassedTo verify whether HAis configured in AP viawlc GUI and able tomake AP failover fromprimary to secondarycontroller andvice-versa.

Configure a Highavailability in APvia wlc GUI andmake AP failover.

WLJ80S_apcrash_01

PassedTo verify whether HAis configured in AP viawlc CLI and able tomake AP failover fromprimary to secondarycontroller andvice-versa.

Configure a Highavailability in APvia wlc CLI andmake AP failover.

WLJ80S_apcrash_02

PassedTo check whetherantenna commandoptions are present inthe Aironet commandreference.

Check whether theantenna commandoptions are presentin Aironet

WLJ80S_apdoc_01

PassedTo verify the clientconnection with TKIPencryption and trafficflow between two TKIPclients

Client connect withTKIP encryption -AP1600

WLJ80S_apenc_01


231

Regression Features - Test SummarySR/CFD Test cases

PassedTo verify the clientconnection with TKIPencryption and trafficflow between TKIP andnon-TKIP clients

Client connect withTKIP encryption -AP1600

WLJ80S_apenc_02

PassedTo verify a clientassociation with theWPA+PSK+TKIPenabled SSID fromAP700 GUI

Configure a SSIDwithWPA+PSK+TKIPsecurity in AP700GUI and associateclient

WLJ80S_apenc_03

PassedTo verify a clientassociation with theWPA+PSK+TKIPenabled SSID fromAP700 CLI

Configure a SSIDwithWPA+PSK+TKIPsecurity in AP700CLI and associateclient

WLJ80S_apenc_04

PassedTo verify a clientassociation with theWPA+PSK+TKIPenabled SSID in wlc5508

Configure a SSIDwithWPA+PSK+TKIPsecurity in wlc 5508and associate client

WLJ80S_apenc_05

PassedTo check whether theradius server config vianew CLI in AP willreflect in Security tableof AP GUI

Radius Serverconfiguration viaCLI reflects in GUI

WLJ80S_apgui_01

PassedTo verify whethertransmitter power isshown properly in GUIor not

Autonomous APtransmitter power

WLJ80S_apgui_02

PassedTo verify whethertransmitter power isshown properly in CLIor not

Autonomous APtransmitter power

WLJ80S_apgui_03

PassedTo check whetherAP3600 bootup properlywithout any flash issuesafter power outage

AP bootup afterpower outage-AP3600

WLJ80S_apios_01

PassedTo check whetherAP2600 bootup properlywithout any flash issuesafter power outage

AP bootup afterpower outage-AP2600

WLJ80S_apios_02


232


PassedTo verify whether theconfigured default routeto BVI interface isremoved by configuringthe default route togateway in LAP whichholds static ip addressand rebooting.

Configure a defaultroute to BVIinterface and togateway for LAPwith static ipaddress

WLJ80S_apios_03

PassedTo verify whether theconfigured default routeto BVI interface isremoved by configuringthe default route togateway in LAP whichholds DHCP ip addressand rebooting.

Configure a defaultroute to BVIinterface and togateway for LAPwith dynamic(DHCP) ip address

WLJ80S_apios_04

PassedTo check all APs areconnected without errormessage after upgrade

"Radio disabled dueto inline power"

WLJ80S_appoe_01

PassedTo verify whether radioslot 0 gets resetautomatically or notwhile installing Radioslot 1 in 3700 AP.

Verifying the radioslot of 3700 AP in5508 WLC

WLJ80S_aprad_01


Verifying the radioslot of 3700 AP invWLC

WLJ80S_aprad_02


Verifying the radioslot of 1142 AP in8508 WLC

WLJ80S_aprad_03

PassedTo verify whether thereis no tx stop happenswhen large beacon/dtimperiod is set in radiointerface.

Radio behaviourwhen largebeacon/dtim periodis set in its interface

WLJ80S_aprad_04

PassedTo verify whether APstarts with 40Mhz afterreboot where channelwidth is configured as40Mhz and auto

AP channel widthafter reboot-AireOS

WLJ80S_aprrm_01


233


PassedTo verify whether APstarts with 40Mhz afterreboot where channelwidth is configured as40Mhz and auto

AP channel widthafterreboot-IOS-XE

WLJ80S_aprrm_02

PassedTo verify whether 11nclients can able totransfer data withinthem or not whileassociated toAutonomous AP.

Associating 11nclients toAutonomous APand checking thedata transferbetween them

WLJ80S_apstats_01

PassedTo verify whether theallowed tx power levelscan be configuredcorrectly by convertingAP2600 as CAP andSAP successfully

check allowed txpower levels can beconfigured correctlyby convertingAP2600 as CAPand SAP

WLJ80S_aptx_01

PassedTo verify whetherbroadcom clients areable to associatesuccessfully or not whenWMM enabled

Broadcom Clientsin AP 3600 whenWMM is enabled

WLJ80S_apunkn_01



WLJ80S_apunkn_02



WLJ80S_apunkn_03

PassedTo verify whether 3600AP is booted upsuccessfullywithout anyunrelated messages.

Boot up the 3600AP

WLJ80S_apunkn_04


Boot up the 2600AP

WLJ80S_apunkn_05


Boot up the 3700AP

WLJ80S_apunkn_06


234



Boot up the 2700AP

WLJ80S_apunkn_07

PassedTo verify whether theradio channel setting isworking as expected asper the configurationguide

check radio channelsetting as per theconfiguration guide

WLJ80S_auap_01

PassedTo check if wips alarmdetedtion time stampisnt ahead of AP clock

wips alarmdetection timestamp is ahead ofAP clock

WLJ80S_awips_01

PassedTo verify whether theHA pair(ACTIVE:STANDBY)is up successfully


WLJ80S_c3p1_01

PassedTo verify the HA paircontroller modes whenthe Gateway is notreachable from theACTIVE controller

Controller modewhen the Gatewayis not reachable tothe ACTIVEcontroller

WLJ80S_c3p1_02

PassedTo verify whether theAP's 802.11a interfacechannel is configuredand the configuredmessages showscorrectly in wlc 5508,physical PI and virtualPI logs.

Configure a channelfor AP's 802.11ainterface and checkthe channel changedmessage in wlc5508, physical PIand Virtual PI logs.

WLJ80S_capwap_01

PassedTo verify whether theAP's 802.11b interfacechannel is configuredand the configuredmessages showscorrectly in wlc 5508,physical PI and virtualPI logs.

Configure a channelfor AP's 802.11binterface and checkthe channel changedmessage in wlc5508, physical PIand Virtual PI logs.

WLJ80S_capwap_02

PassedTo verify whether theAP's 802.11a interfacechannel is configuredand the configuredmessages showscorrectly in wlc 8500,physical PI and virtualPI logs.

Configure a channelfor AP's 802.11ainterface and checkthe channel changedmessage in wlc8500, physical PIand Virtual PI logs.

WLJ80S_capwap_03


235


PassedTo verify whether theAP's 802.11b interfacechannel is configuredand the configuredmessages showscorrectly in wlc 8500,physical PI and virtualPI logs.

Configure a channelfor AP's 802.11binterface and checkthe channel changedmessage in wlc8500, physical PIand Virtual PI logs.

WLJ80S_capwap_04

PassedTo verify whether theAP's 802.11a interfacechannel is configuredand the configuredmessages showscorrectly in virtual wlc,physical PI and virtualPI logs.

Configure a channelfor AP's 802.11ainterface and checkthe channel changedmessage in virtualwlc, physical PI andVirtual PI logs.

WLJ80S_capwap_05

PassedTo verify whether theAP's 802.11b interfacechannel is configuredand the configuredmessages showscorrectly in virtual wlc,physical PI and virtualPI logs.

Configure a channelfor AP's 802.11binterface and checkthe channel changedmessage in virtualwlc, physical PI andVirtual PI logs.

WLJ80S_capwap_06

PassedTo check the DTLShandshakemessages forcorrupted data afterrejoining the AP withWLC

Reconnect AP withWLC and check theHandshakemessages

WLJ80S_capwap_07

PassedTo check whether oldDTLS data encryptionsession is still present inthe WLC

Check the oldDTLS dataencryption sessionsin WLC

WLJ80S_capwap_08

PassedTo check whether oldDTLS data encryptionsession is still present inthe WLC with AP stillconnected

Check the oldDTLS dataencryption sessionsin WLC withconnected AP

WLJ80S_capwap_09

PassedTo check and verifywhether the AP entry isavailable in the databaseafter the AP isassociated with theWLC

Check the AP entryavailable in thedatabase

WLJ80S_capwap_10


236


PassedTo verify whetherclients are filtered basedon SSID with the timeframemore than an houror not

Client trafficfiltered based onSSID

WLJ80S_cmgmt_01

PassedTo verify whetherclients are filtered basedon Device IP Addresswith the time framemore than an hour or not

Client trafficfiltered based onDevice IP Address

WLJ80S_cmgmt_02

PassedTo verify whetherclients are filtered basedon Device Host Namewith the time framemore than an hour or not

Client trafficfiltered based onDevice Host Name

WLJ80S_cmgmt_03

PassedTo verify whetherwireless clients runningcisco jabber is classifiedas SSL when client isconnected to AVCenabled WLAN

AVC visibility forCisco jabberapplications

WLJ80S_com_01

PassedTo verify the Nose andinterference report hasbeen generated whenunified AP is selected inLC > DWC

PI-Noise/Interferencereport for UnifiedAps in LC theme

WLJ80S_conwl_01

PassedTo verify whetherNeighbor address detailsare displayed in Hex ornot in PI

Checking theneighbor addressdetails in PI

WLJ80S_conwl_02

PassedTo verify whether theclients are connectedusing internal DHCPscope offer

check the client ableto get the internalwlc dhcp scopeoffer

WLJ80S_dhcp_01

PassedTo check if client statusdisplay appropriately -2500

VLAN isn't markedas dirty whenre-connect clientcannot get IP viaDHCP

WLJ80S_doc_01



WLJ80S_doc_02


237




WLJ80S_doc_03



WLJ80S_doc_04

PassedTo verify whether 2504Express setup supportedbrowsers is updated ornot in 7.6Mr3 releasenotes and checkwhetherdashboards worksproperly or not in allbrowsers.

Checking theupdate of 2504Express setup inrelease notes andchecking thedashboardfunctionality in allbrowsers.

WLJ80S_doc_05

PassedTo verify whether theWLCmanaged from thewireless client

check the WLCmanaged from thewireless client whenmanagement viawireless enabled

WLJ80S_error_01

PassedTo check if lag fail overworks in 5500

LAG fail-over doesnot work onCT5508Â

WLJ80S_fwd_01


LAG fail-over doesnot work on 7500

WLJ80S_fwd_02


LAG fail-over doesnot work on 8500

WLJ80S_fwd_03

PassedTo verify whether theguest user configurationis retained in a WLCafter config upload anddownload or not

Uploading andDownloading guestuser configurationin WLC

WLJ80S_guest_01

PassedTo verify whether theguest user configurationis retained in a WLCafter rebooting or not

Guest userconfiguration inWLC afterrebooting

WLJ80S_guest_02


238


PassedTo verify whetherscheduled guest user iscreated and removedfrom physical PI andWLC 5508 after its timeexpired

Check thescheduled guestuser is removedfrom Physical PIand WLC 5508after its timeexpired

WLJ80S_guest_03

PassedTo verify whetherscheduled guest user iscreated and removedfrom virtual PI andWLC 5508 after its timeexpired

Check thescheduled guestuser is removedfrom virtual PI andWLC 5508 after itstime expired

WLJ80S_guest_04

PassedTo verify whether thefalse redundancyhearbeat loss failveroccur on WLC HAfailover

check the controllerHA failover falseredundancyheartbeat loss

WLJ80S_ha_01

PassedTo verify whetherflexconnect AP changesmode when controller(5508) is down/up.

H-REAP betweenconnected andstandalone AP

WLJ80S_hreap_01



WLJ80S_hreap_02



WLJ80S_hreap_03

PassedTo check and verify theAP connection status toWLC after configuringthe VLAN mapping

Check APconnection status toWLC after VLANmapping configusing 7510

WLJ80S_hreap_04

PassedTo check and verify theAP connection status toWLC after configuringthe VLANmapping andreconnect the AP withWLC afterdisconnecting.

Check APconnection status toWLC after VLANmapping config

WLJ80S_hreap_05


239


PassedTo verify whether webauth with flex localswitching is able tocreate and apply pre andpost auth flex acl to itand associate client andcheck webauthentication in wlc5508

Configure a webauth with pre andpost auth flex ACLin wlc 5508

WLJ80S_hreap_10

PassedTo verify whether webauth with flex localswitching is able tocreate and apply pre andpost auth flex acl to itand associate client andcheck webauthentication in wlc8500

Configure a webauth with pre andpost auth flex ACLin wlc 8500

WLJ80S_hreap_11

PassedTo verify the aIOS APtelnet session and txloadin AP's interfaces

AP telnet sessiondue to tx load in theinterfaces

WLJ80S_idb_01

PassedTo verify whether theWLC deletedsuccuessfully afterupgrade from WLC oldversion to new version

check the WLCdeleted from PIafter upgrade WLCfrom the old version

WLJ80S_inv_01

PassedTo verify whetherMulticast state can bedisabled in WLCsuccessfully or not

DisablingMulticaststate in WLC GUI

WLJ80S_lan_01

PassedTo verify whetherMulticast state can bedisabled in WLCsuccessfully or not

DisablingMulticaststate in WLC CLI

WLJ80S_lan_02

PassedTo verify whetherlicenses can be removedor not in HA SKUWLCother than base license.

Trying to removelicenses in WLC

WLJ80S_lic_01

PassedThis is to verify theARP entry in thenetwork by adding theAP's to the Wirelesscontroller and addingthe clients

Add AP to theWLC and checkARP entry to thenetwork using2500,5508

WLJ80S_logger_01


240


PassedTo verify whether theheapmap and AP colourstatus are showingsuccessfully on the floorview

check the heapmapand AP colourstatus are showingon the floor view

WLJ80S_maps_01

PassedTo check and findwhether any memoryleaks occur from thelogs of AP

Check the outputlogs for AP consolefor memory leaks

WLJ80S_memry_01

PassedTo check the MSEadmin view launch fromPI server

MSE Admin Viewfrom PI server

WLJ80S_mse_01

PassedTo check whether pidisplays clients androgue AP in floor view

PI 1.4 don't displayclients and rogueAP on floor view

WLJ80S_mse_02

PassedTo verify whether MSEable to track the clientsor not after sync/re-syncthe Maps.

Checking the MSEtracking functionafter sync/resyncthe Maps.

WLJ80S_mseloc_01

PassedTo check if there is anysuspicious after hourstraffic detected duringworking hours

Suspiciousafter-hours trafficdetected duringworking hours

WLJ80S_msesw_01

PassedTo check whether thereis no timed out errorduring NTP sync

NTP sync faileddue to timed out,nothing received

WLJ80S_msesw_02

PassedTo verify whetherDB(Database) passwordis able to config or notin MSE.

Setting the DBpassword in MSE.

WLJ80S_msesw_03

PassedTo verify whetherOracle DB(Database)password is able tore-config or not inMSE.

Resetting theOracleDB password inMSE.

WLJ80S_msesw_04

PassedTo check whether ap'sare saving the history inthe database of the mse

Check the logs ofmse for the historyof the ap's

WLJ80S_msesw_05

PassedTo verify whethertheKatana/Edison isbooting up after upgradewhen service config isconfigured

check theKatana/Edisonbooting afterupgrade orrebooting whenserviceconfigurationcompleted

WLJ80S_osbt_01


241


PassedTo check the PI fullcompatibility with thelatest upgraded chromebrowser

Check thecompatibility of PIwith latest chromebrowser

WLJ80S_prime_01

PassedTo check the PI fullcompatibility with thelatest upgraded chromebrowser

Check thecompatibility of PIwith latest chromebrowser

WLJ80S_prime_02

PassedTo check After a fewfailovers whether clientsget authenticated

After few failoversNone of the Clientsget authenticated

WLJ80S_rrm_05



WLJ80S_rrm_06



WLJ80S_rrm_07

PassedTo check if Floor mapsin PI loads without anyexceptions

Floor maps in PIfail to load withwidget exceptions

WLJ80S_rrm_08

PassedTo verify whether theAPTransmit(Tx) powerlevel for 802.11a isconfigured from thecontroller GUI

Configure the APtransmit (Tx) powerlevel for 802.11afrom controller GUI

WLJ80S_rrm_09

PassedTo verify whether theAPTransmit(Tx) powerlevel for 802.11a isconfigured from thecontroller CLI

Configure the APtransmit (Tx) powerlevel for 802.11afrom controller CLI

WLJ80S_rrm_10

PassedTo verify whether theAPTransmit(Tx) powerlevel for 802.11b isconfigured from thecontroller GUI

Configure the APtransmit (Tx) powerlevel for 802.11bfrom controller GUI

WLJ80S_rrm_11

PassedTo verify whether theAPTransmit(Tx) powerlevel for 802.11b isconfigured from thecontroller CLI

Configure the APtransmit (Tx) powerlevel for 802.11bfrom controller CLI

WLJ80S_rrm_12

PassedTo verify whether theapplied local policy onwlan is working asexpected when activehours defined

check the appliedlocal policy onWLAN is workingon specified activehours

WLJ80S_sec_01


242


PassedTo verify whether theOUImatch is happeningsuccessfully foriphone5s nativeprofiling

check the OUImatch is happeningwhen use theiPhone5s for nativeprofiling

WLJ80S_sec_02

PassedTo check and verify thesession timeouts for theclients associated withwlc while in roaming

Check the sessiontimeouts for theclients in roaming

WLJ80S_sec_03

PassedTo enable theInfrastructure MFP inWLC and check for anyMFP anomalymessagesgenerated by rogueclients/ap's

Check for MFPanomaly messagesafter enabling theInfrastructure MFP

WLJ80S_sec_04

PassedTo disable theInfrastructure MFP inWLC and check for anyMFP anomalymessagespresent in the logsgenerated by rogueclients/ap's

Check for MFPanomaly messagesafter disabling theInfrastructure MFP

WLJ80S_sec_05

PassedTo verify whether thesystem acceptsmodifying defaultSNMP community ornot

Modification ofdefault communitywith non defaultvalues in GUI

WLJ80S_snmp_01

PassedTo verify whether thesystem acceptsmodifying defaultSNMP community ornot

Modification ofdefault communitywith non defaultvalues in CLI

WLJ80S_snmp_02

PassedTo verify whether thesystem accepts creationof SNMPV3 user named"default" or not

Creation ofSNMPV3 usernamed "default" inGUI

WLJ80S_snmp_03

PassedTo verify whether thesystem accepts creationof SNMPV3 user named"default" or not

Creation ofSNMPV3 usernamed "default" inCLI

WLJ80S_snmp_04

PassedTo verify whether thesystem accepts creationof non-defaultcommunity withnon-default values ornot

Creation ofnon-defaultcommunity withnon-default valuesin GUI

WLJ80S_snmp_05


243


PassedTo verify whether thesystem accepts creationof non-defaultcommunity withnon-default values ornot

Creation ofnon-defaultcommunity withnon-default valuesin CLI

WLJ80S_snmp_06

PassedTo check on accessingfloor maps in PIserver(Standalone)doesn't cause the serverto crash

PI server afteraccessing floormaps-Standalonebox

WLJ80S_sys_01

PassedTo check on accessingfloor maps in PIserver(HA enabled)doesn't cause the serverto crash

PI server afteraccessing floormaps-HA enabledbox

WLJ80S_sys_02

PassedTo verify whether PI getcrashed or not whileaccessing floor mapswith more number ofAP's added in it.

Adding morenumber of AP's inFloor maps.

WLJ80S_sys_03

PassedTo verify whether theshow network summaryresults matches therunning config or not

APMulticast Modewith blankMulticast GroupAddress in GUI

WLJ80S_web_01

PassedTo verify whether theshow network summaryresults matches therunning config or not

APMulticast Modewith blankMulticast GroupAddress in CLI

WLJ80S_web_02

PassedTo verify whether theJapanese DBCScharacters is garbled ornot in internal Webauthlogin.html page

Japanese DBCScharacters inInternal WebAuth

WLJ80S_web_03

PassedTo verify whether theJapanese DBCScharacters is garbled ornot during externalWebauthentication

Japanese DBCScharacters inExternal WebAuth

WLJ80S_web_04

PassedTo verify Whether apparameters are able toconfigure from 5508controller GUI

Configure the APparameters fromController GUI

WLJ80S_web_05


244


PassedTo verify Whether apparameters are able toconfigure from 5508controller CLI

Configure the APparameters fromController CLI

WLJ80S_web_06

PassedTo verify Whether apparameters are able toconfigure from 8500controller GUI

Configure the APparameters fromController GUI

WLJ80S_web_07

PassedTo verify Whether apparameters are able toconfigure from 8500controller CLI

Configure the APparameters fromController CLI

WLJ80S_web_08

PassedTo verify whether webauthentication happensfor a client reconnectedto an SSID withdifferent IP address ornot

Client reconnectionto a SSID withdifferent IP address

WLJ80S_webauth_01

PassedTo verify whether webauthentication happensfor a client reconnectedto an SSIDwith same IPaddress or not

Client reconnectionto a SSID withsame IP address

WLJ80S_webauth_02

PassedTo verify whether webauthentication happensfor a client afterrenewing the IP addressfrom the DHCP or not

Web authenticationafter renewing theIP address fromDHCP

WLJ80S_webauth_03

PassedTo verify the radiopolicy of WLAN/APgroup byupgrading/downgradingthe WLC build

AP group radiopolicy bydowngrading/upgradingbuild

WLJ80S_wlan_01

PassedTo verify the radiopolicy of WLAN/APgroup after savingconfig and rebooting theWLC

AP group radiopolicy afterrebooting the WLC

WLJ80S_wlan_02

PassedTo verify the radiopolicy of APgroup/WLAN afterdownloading anduploading the config file

AP group radiopolicy afteruploading thebackup config

WLJ80S_wlan_03


245


PassedTo verify the radiopolicy by connectingclients to the specificradio which is set inWLC "a only"

AP group radiopolicy whenconnecting clientwith specific radiopolicy "a only"

WLJ80S_wlan_04

PassedTo verify the radiopolicy by connectingclients to the specificradio which is set inWLC as "b/g only"

AP group radiopolicy whenconnecting clientwith specific radiopolicy "b/g only"

WLJ80S_wlan_05

PassedTo verify the radiopolicy of custom apgroup has been retainedafter upgrade WLC7500

WLC 7500: Radiopolicy in customAP group- Upgrade

WLJ80S_wlan_06

PassedTo verify the radiopolicy of custom apgroup has been retainedafter config upload

WLC 7500: Radiopolicy in customAP group- configrestore

WLJ80S_wlan_07

PassedTo verify whetherclients connect to theexplicitly configuredradio policy of APgroup

WLC 7500: Radiopolicy in customAP group- Clientconnectivity

WLJ80S_wlan_08

PassedTo verify whetherclients connect to theexplicitly configuredradio policy of APgroup in NGWC

NGWC: CheckingRadio policy setting

WLJ80S_wlan_09

PassedTo verify whether theclients connects tospecified radio policyset on the controller

check the voiceclients connects tospecified radiopolicy

WLJ80S_wlan_10

PassedTo verify whether thetimestamp-tolerance isshown properly or notin show running-configoutput

Timestamp-tolerancein Guest LAN

WLJ80S_wlan_11

To verify whetherWlan's(ID > 16) stategets disabled or not afterrebooting the 5508WLC.

Checking theWLAN state afterrebooting the 5508WLC.

WLJ80S_wlan_12


246


To verify whetherWlan's(ID > 16) stategets disabled or not afterrebooting the 8500WLC.

Checking theWLAN state afterrebooting the 8500WLC.

WLJ80S_wlan_13

PassedTo verify whetherWlan's(ID > 16) stategets disabled or not afterrebooting the vWLC.

Checking theWLAN state afterrebooting thevWLC.

WLJ80S_wlan_14

PassedTo verify whetherWlan's(ID > 16) stategets disabled or not afterupload/download theconfig file in 5508WLC.

Checking theWLAN state afterupload/downloadthe config file in5508 WLC.

WLJ80S_wlan_15

PassedTo verify whetherWlan's(ID > 16) stategets disabled or not afterupload/download theconfig file in 8500WLC.

Checking theWLAN state afterupload/downloadthe config file in8500 WLC.

WLJ80S_wlan_16

PassedTo verify whetherWlan's(ID > 16) stategets disabled or not afterupload/download theconfig file in vWLC.

Checking theWLAN state afterupload/downloadthe config file invWLC.

WLJ80S_wlan_17

PassedTo verify whether alldynamic interfacescreated has beenrestored after configdownload

Dynamic interfacesetting in WLC

WLJ80S_wlcos_01

PassedTo verify whether thedowngrading of WLCimage is working asexpected

check thedowngrading ofWLC show theerror AP imagebundle is notunbundled

WLJ80S_wlcos_02

PassedTo verify whethervWLC Ova is able toinstall successfully ornot with UCS server.

Checking thedeployment ofvWLC with UCSserver.

WLJ80S_wlcvm_01

SR Test Cases



247


PassedTo check and verifyenabling/disabling the802.11ac networkfrom WLC GUI.

Enable/disable the802.11ac network fromWLC CLI.

WLJ80S_11AC_01

PassedTo check and verifyenabling /disabling the802.11ac networkfrom WLC CLI

Enable/disable the802.11ac network fromWLC GUI.

WLJ80S_11AC_02

PassedTo verify the runningconfig after powe loss

Verification of Runningconfig after powe loss

WLJ80S_APCON_01

PassedTo verify the defaultroute after configuringthe default gateway

Verification of defaultroute after setting thegateway

WLJ80S_APCON_02

PassedTo verify the runningconfig after powe loss

Verification of Runningconfig after reset byWLCGUI

WLJ80S_APCON_03

PassedTo verify the clientbehaviour whenbroadcasting SSID isdiabled where clientsare in connected state

Checking SSIDbroadcasting disablewhenclients are in connectedstate

WLJ80S_APGRP_01

PassedTo check that thedot1x authenticatedclient should notdisassocite aftersession timeout expires

Session timeout for dot1xassociated client

WLJ80S_APGRP_02

PassedTo check the clientroaming form one APgroup to another APgroup providedWLAN is mapped tomultiple AP groupswith different VLAN

Client roam across APgroups with WLANmapped to differentVLAN

WLJ80S_APGRP_03

PassedTo check the clientroaming form one APgroup to another APgroup providedWLAN is mapped tomultiple AP groupswith different VLANwhere FLS is enabledin the WLAN

Client roam across APgroups with WLANmapped to differentVLAN- FLS enabled

WLJ80S_APGRP_04

PassedTo check the dynamicVLAN assignment fora client in WLC 2504

Dynamic VLANassignment- WLC 2504

WLJ80S_APGRP_05


248


PassedTo check whetherdefault gateway toBVI1 config is presentor not in show runningcommand of AP CLI.

Checking the defaultgateway config in showrunning command of APCLI.

WLJ80S_APIOS_01

PassedTo verify the channelselection in AP

Channel selection in APWLJ80S_APRAD_01

PassedTo check whetherActive HA WLC goesto standy by WLC orto backup port whileprimary port is down.

Configuring backup portfor Active port of ActiveHA WLC.

WLJ80S_EAP_01

PassedTo check whetherexcluded client presentin Monitor > Clientspage is able to deleteor not in WLC GUI.

Trying to delete excludedclient present in Monitor> Clients page.

WLJ80S_EAP_02

PassedTo check whetherCPU process valuegetting greater than 1or not via WLC CLIwhen 3-4 associateddot1x clients aredeauthenticated atonce in WLC GUI.

Deauthenticating moreassociated dot1x clientsand checking the CPUprocess value in WLCCLI.

WLJ80S_EAP_04

PassedTo check whethererror message occursor not when a client isgetting redirected toweb-auth login pagewhile it is gettingassociated to aWLANwith securitydot1x+webauth

Associating a client to aWLAN with securitydot1x+Webauth in 5508WLC.

WLJ80S_EAP_05

PassedTo check whetherinvalid mac addresscan be added or not inlocal mac filter page ofWLC via GUI.

Adding Invalid macaddress in local mac filterpage of 5508 WLC viaGUI

WLJ80S_EAP_06

PassedTo check whetherinvalid mac addresscan be added or not inlocal mac filter page ofWLC via CLI.

Adding Invalid macaddress in local mac filterpage of 5508 WLC viaCLI

WLJ80S_EAP_07


249


PassedTo check whetherSamsung S4 clientroams or not between2 WLC's with dot1xsecurity.

Roaming Samsung S4client between wlc's withdot1x security.

WLJ80S_EAP_08

PassedTo check whetherApple Iphone clientroams or not between2 WLC's with dot1xsecurity.

Roaming Apple Iphoneclient between wlc's withdot1x security.

WLJ80S_EAP_09

PassedTo check whether win8 client associated ornot to a WLAN withsecuritydot1x+webauth in8500 WLC.

Associating aWin 8 clientto a WLAN with securitydot1x+Webauth in 8500WLC.

WLJ80S_EAP_10

PassedTo check whether win8 client associated ornot to a WLAN withsecuritydot1x+webauth invWLC.

Associating aWin 8 clientto a WLAN with securitydot1x+Webauth invWLC.

WLJ80S_EAP_11

PassedTo check whether win8 client gets associatedor not to a WLANwith securityDot1x(PEAP withTLS).

Associating Win 8 clientto a WLAN with securityDot1x(PEAP with TLS).

WLJ80S_EAP_12

PassedTo check whetherclients gets associatedor not to 1142 AP in5508 WLC with allsecurity types.

Associating wirelessclients to 1142 AP withdifferent L2&L3 securitytypes in 5508 WLC.

WLJ80S_EAP_13

PassedTo check whetherSSID field is presentor not in CLIcommand of showradius summary.

Checking the availabilityof SSID field in "showradius summary"command.

WLJ80S_EAP_14

PassedTo check theWLAN-VLANmapping forlocalswitching centralauth config in case offault tolerance

WLAN-VLAN mappingfor localswitching centralauth configuration- FT

WLJ80S_FLEX_01


250


PassedTo check theWLAN-VLANmapping forlocalswitching localauth config in case offault tolerance

WLAN-VLAN mappingfor localswitching localauth configuration- FT

WLJ80S_FLEX_02

PassedTo check theWLAN-VLANmapping when APboots in connectedmode

WLAN-VLAN mappingwhen AP boots inconnected mode

WLJ80S_FLEX_03

PassedTo check theWLAN-VLANmapping when APboots in SA mode

WLAN-VLAN mappingwhen AP boots in SAmode

WLJ80S_FLEX_04

PassedTo check theWLAN-VLANmapping forlocalswitching centralauth config when APmoves from connectedto Sa mode and viceversa

WLAN-VLAN mappingfor localswitching centralauth configuration whenAPmoves from connectedto SA mode

WLJ80S_FLEX_05

PassedTo check theWLAN-VLANmapping forlocalswitching localauth config when APmoves from connectedto Sa mode and viceversa

WLAN-VLAN mappingfor localswitching localauth configuration whenAPmoves from connectedto SA mode

WLJ80S_FLEX_06

PassedTo check whetherconfigured VLANmapping is saved uponsave config on WLCinstead of changing tonativa VLAN

Flexconnect VLANmapping upon save configin WLC

WLJ80S_FLEX_07

PassedTo check the OEAPassociation with WLC2504

OEAP setup with WLC2504

WLJ80S_FLEX_08

PassedTo verify FLS clientsconnected via AP3502shouldn't experienceany intermittentdisconnection

FLS clients via AP3502WLJ80S_FLEX_09


251


PassedTo check whetherflexconnect AP can beable to service clientswhen WAN outageand AP is rebooted inSA mode

Flexconnect AP behaviorwhen reboot in SA mode

WLJ80S_FLEX_10

PassedTo check whetheriPads are able to listthe wifi networks andable to connect to it

iPad Client association toWLC 7500- Centralswitching

WLJ80S_FLEX_11

PassedTo check whetheriPads are able to listthe wifi networks andable to connect to it

iPad Client association toWLC 7500- Localswitching

WLJ80S_FLEX_12

PassedTo check whether FLSclients didn'tdisconnect when APmoves from connectedto SA mode

FLS clientswhen movefrom connected to SAmode- WLC 7500

WLJ80S_FLEX_13

PassedTo check whether FLSclients didn'tdisconnect when APmoves from SA toconnected mode

FLS clientswhen movefrom SA to connectedmode- wlc 7500

WLJ80S_FLEX_14

PassedTo check there is nodouble AID allocationin flexconnect APwhile clientconnectivity

Client connectivity inFlexconnect AP

WLJ80S_FLEX_15

PassedTo check the clientconnectivity to OEAP

Client connectivity toOEAP

WLJ80S_FLEX_16

PassedTo check whether themodifiction of oneSSID wont affect theother SSID with samename

Flexconnect AP withmultiple SSIDs havingsame name

WLJ80S_FLEX_17

PassedTo verify whetherclients connectedwhenconfig file is manuallyedited with cleartextascii/hex key

Config import by addingascii/hex key manually inWLC config file

WLJ80S_FLEX_18

PassedTo verify thede-authenticationframes for client

De-authentication framesWLJ80S_FLEX_19


252


PassedTo verify the ipv6disable on WLC

Disabling the ipv6 onWLC

WLJ80S_Ipv6_01

PassedTo verify whether theWLC adder licsenseloses after system reseton WLC

check the WLC adderloses after the systemreset

WLJ80S_LIC_01

PassedTo check and associatea wireless client with5500 controller andping the networkthrough GUI

To associate a client withcontroller and ping thenetwork

WLJ80S_LWAPP_01

PassedTo check and associatea wireless client with5500 controller andping the networkthrough CLI

To associate a client withcontroller and ping thenetwork

WLJ80S_LWAPP_02

PassedTo verify whether theAP is able topre-download theimage from thecontroller 5500 usingGUI

To upgrade the AP imageby pre-download fromcontroller

WLJ80S_LWAPP_03

PassedTo verify whether theAP is able topre-download theimage from thecontroller 5500 usingCLI

To upgrade the AP imageby pre-download fromcontroller

WLJ80S_LWAPP_04

PassedTo verify the jumboframes by default

Jumbo frames by Lightweight AP

WLJ80S_LWAPP_05

PassedTo verify thecorresponding MFPlogs

verification of MFP logsWLJ80S_MFP_01

PassedCheck if there is noping loss afterupgrading the WLC

Ping loss after upgradingWLJ80S_MGTERR_01





PassedCheck if WLCsyncronize with NTP

WLCdon't synchronize toNTP

WLJ80S_MGTERR_04


253


PassedCheck if there is nooverrides disabledmessages appears

Massive Radius overridesdisabled messages areobserved

WLJ80S_MGTERR_05



WLJ80S_MGTERR_06



WLJ80S_MGTERR_07



WLJ80S_MGTERR_08

PassedCheck if AP andController time zone issame

AP always use UTC, notthe controllers timezone

WLJ80S_MGTERR_09



WLJ80S_MGTERR_10



WLJ80S_MGTERR_11



WLJ80S_MGTERR_12

PassedCheck if APconfiguration can besaved in NCS

WLC: cannot save APconfiguration on NCS

WLJ80S_MGTERR_13

PassedCheck if 7500 is ableto shutdown usingIMM

Shutting down 7500WLJ80S_MGTERR_14

PassedCheck if 8500 is ableto shutdown usingIMM

Shutting down 8500WLJ80S_MGTERR_15

PassedCheck if adminpassword is changedthrough cli

Admin password changein 2500

WLJ80S_MGTERR_16



WLJ80S_MGTERR_17



WLJ80S_MGTERR_18


254




WLJ80S_MGTERR_19

PassedTo check if differentVlan can ve assignedper SSID

Assign different VLANper SSID

WLJ80S_MGTERR_20

PassedTo check if there is noerror message afterupgrading

CT2504 message about #APF - 1 - ADD _ TO _BLACKLIST _ FAILED

WLJ80S_MGTERR_21

PassedTo check if there is nopre-download failure

CAP2600 pre-downloadfailure

WLJ80S_MGTERR_22

PassedTo check if errormessages are proper

Syslog server errormessages

WLJ80S_MGTERR_23

PassedTo check and verifythe clients connectivityin wireless mobilityfeature.

Check the wirelessmobility feature in 2500

WLJ80S_MOBILITY_01

PassedTo verify whetherconfiguration of MSEstrong root passwordreflected after reboot

check the MSE strongroot passwordconfiguration

WLJ80S_MSE_01

PassedTo verify whetherMSE shows the powersupply status usingspecified command

check the power supplystatus of MSE

WLJ80S_MSE_02

PassedTo verify whether theMSE tracks the clientwhen increase the APlicense or decrease theAP count

check MSE tracks clientwith respect to the licenselimit

WLJ80S_MSE_03

PassedTo verify whether theMSE and WLC showsthe same rogue APcount status

check the rogue AP counton both MSE and WLC

WLJ80S_MSE_04

PassedTo verify whether thePI and MSE show thewrong license errormessages afterupgrading

check any license errorshow after upgradingNCS and MSE

WLJ80S_MSE_05

PassedTo verify whether theMSE WIPS exceptionerror occur whenMSEforward traps

check the Wips exceptionerror occurance whenMSE framework forwardtraps and PI receive anyalarm

WLJ80S_MSE_06


255


PassedTo verify thescheduled admin statuschange ,enable

Scheduled admin (Enable)status change by PI

WLJ80S_PIADM_01

PassedTo verify thescheduled admin statuschange disable

Scheduled admin(Disable))status changeby PI

WLJ80S_PIADM_02

PassedTo verify whether ableto add MSE to PIwhen using thedifferent types ofMSEnames

check the integration ofMSE to PI with differentnames

WLJ80S_PIMSE_01

PassedTo verify the PIreports with clientbandwidth

PI reports with clientbandwidth

WLJ80S_PIREP_01

PassedTo check theconnectivity status ofthe connected clientswith the wirelesscontroller 2500

Check the connectivity ofthe connected clients

WLJ80S_RCV_01

PassedTo check theconnectivity status ofthe connected clientswith the wirelesscontroller 2500

Check the connectivity ofthe connected clients

WLJ80S_RCV_02

PassedTo check the firmwareupgrading process forthe access pointsthrough gui

Upgrading the firmwareof the access points

WLJ80S_RCV_03

PassedTo check the firmwareupgrading process forthe access pointsthrough cli

Upgrading the firmwareof the access points

WLJ80S_RCV_04

PassedTo check whethercustom channel 52 isable to set or not in2600 AP via WLCCLI.

Setting custom channel in2600 AP via WLC CLI

WLJ80S_RRM_01

PassedTo check whether dcasensitivityconfiguration(configuredvia WLC CLI) ispresent or not in 5508WLC afterupload/download theconfig file.

Checking the config ofdca sensitivity afterupload/download theconfig file in 5508 WLC.

WLJ80S_RRM_02


256


PassedTo check whether dcasensitivityconfiguration(configuredvia WLC CLI) ispresent or not in 8500WLC afterupload/download theconfig file.

Checking the config ofdca sensitivity afterupload/download theconfig file in 8500 WLC.

WLJ80S_RRM_03

PassedTo check whether dcasensitivityconfiguration(configuredvia WLC CLI) ispresent or not invWLC afterupload/download theconfig file.

Checking the config ofdca sensitivity afterupload/download theconfig file in vWLC.

WLJ80S_RRM_04

PassedTo check whetherbeamformingconfiguration can beenabled or not inWLCvia CLI commands

Enabling beamformingconfiguration inWLC viaCLI commands

WLJ80S_RRM_05

PassedTo check whethercustom channels areconfigured or not inWLC GUI withoutdisabling networkstatus.

Trying to enable customchannels in WLC GUIwithout disabling networkstatus

WLJ80S_RRM_06

PassedTo check whether APradio's getting reset ornot in WLC once DFSdetection event isperformed.

PerformingDFS detectionevent in WLC

WLJ80S_RRM_07

PassedTo verify the de authframes with DCARRM

De-auth frames withRRM DCA

WLJ80S_RRM_08

PassedTo check whethercustom channel 52 isable to set or not in2600 AP via WLCGUI.

Setting custom channel in2600 AP via WLC GUI

WLJ80S_RRM_09

PassedTo check and uploadthe config backup ofthe wireless controllerto the TFTP serverthrough GUI

To upload the configbackup to the TFTP server

WLJ80S_SWUPG_01


257


PassedTo check and uploadthe config backup ofthe wireless controllerto the TFTP serverthrough CLI

To upload the configbackup to the TFTP server

WLJ80S_SWUPG_02

PassedTo verify whether APis getting imagesuccessfully from thecontroller afterupgrading the WLCimage using GUI

Verify whether AP isgetting image successfullyfrom the controller

WLJ80S_SWUPG_03

PassedTo verify whether APis getting imagesuccessfully from thecontroller afterupgrading the WLCimage using CLI

Verify whether AP isgetting image successfullyfrom the controller

WLJ80S_SWUPG_04

PassedTo check and upgradethe wireless LANcontroller image for2500 through GUI

To upgrade the wirelessLAN controller imageusing tftp

WLJ80S_SWUPG_05

PassedTo check and upgradethe wireless LANcontroller image for2500 through CLI


WLJ80S_SWUPG_06

PassedTo verify whether theAP is able topre-download theimage from the 2500controller using GUI

To pre-download APimage from controller

WLJ80S_SWUPG_07

PassedTo verify whether theAP is able topre-download theimage from the 2500controller using CLI

To pre-download APimage from controller

WLJ80S_SWUPG_08

PassedTo check and installthe avc protocol packloaded in the controller

To Install the AVCprotocol pack in thecontroller

WLJ80S_SWUPG_09


To upgrade the wirelessLAN controller imageusing ftp

WLJ80S_SWUPG_10


258




WLJ80S_SWUPG_11



WLJ80S_SWUPG_12



WLJ80S_SWUPG_13



WLJ80S_SWUPG_14



WLJ80S_SWUPG_15

PassedTo verify whether thePI composite templateapplied successfullywithout any issue

check the PI compositetemplate is applied to theWLC

WLJ80S_TEMP_01

PassedTo verify theconfiguration for FlexACL for LAP

web-auth ACL for LAP-5508,3500

WLJ80S_WEBACL_01

PassedTo verify theconfiguration for FlexACL for LAP

web-auth ACL for LAP-5508 WLC ,3600 AP

WLJ80S_WEBACL_02

FailedTo check after webpassthrough, the clientredirects to therequested url providedL2 security asWPA2-PSK and usingcustomized web loginpage

Web auth redirection withL2 sec as WPA2-PSK-Customized login

WLJ80S_WEBAUTH_01


259


PassedTo check after webpassthrough, the clientredirects to therequested url providedL2 security asWPA2-PSK and usinginternal web loginpage

Web auth redirection withL2 sec as WPA2-PSK-internal login

WLJ80S_WEBAUTH_02

PassedTo verify the loginpage with customizedsettings reflects whenclient redirects forauthentication

Customizing the defaultlogin page- web auth

WLJ80S_WEBAUTH_03

PassedTo verify whether thecustomized login pagereflects when client isauthenticating via L3webauth

Loading customizedwebauth bundle

WLJ80S_WEBAUTH_04

PassedTo verify whether webauth redirection issuccessful whenconnecting iPhonewith iOS7 and Safaribrowser

Web authentication foriPhone

WLJ80S_WEBAUTH_05

PassedTo verify whether thewebauth bundle hasbeen extractedsuccessfully in WLC

Web auth bundleextraction in WLC

WLJ80S_WEBAUTH_06

PassedTo verify whether theguest wlan clientsacquires their ipaddress from externaldhcp server

Guest wlan clients'acquiring ip address fromexternal dhcp server

WLJ80S_WEBAUTH_07

PassedTo verify whether therestore of MSE WIPSpolicy is successful

restore the MSE WIPSpolicy

WLJ80S_WIPS_01

PassedTo verify thesyncronzation lossbetween MSE and Pwhen theWIPS policyenabled

check the syncronizationof MSE and PI when theWIPS policy enable

WLJ80S_WIPS_02

PassedTo verify whether theWIPS profile isapplied successfullyfrom the PI to MSE

check the WIPS profile isapplied from the PI toMSE

WLJ80S_WIPS_03


260


PassedTo verify whetheropen authenticationSSID is able to createon both radios in1142AP GUI andclient is able toassociate with it.

Configure a openauthentication SSID onboth radios in AP1142GUI and associate a client

WLJ80S_WLAN_05

PassedTo verify whetheropen authenticationSSID is able to createon both radios in1142APCLI and clientis able to associatewith it.

Configure a openauthentication SSID onboth radios in AP1142CLI and associate a client.

WLJ80S_WLAN_06

PassedTo verify whether theautonomous AP1262is upgraded fromGUI.

Upgrade the autonomousAP1262 from GUI

WLJ80S_WLAN_07

PassedTo verify whether theautonomous AP1262is upgraded from CLI.

Upgrade the autonomousAP1262 from CLI

WLJ80S_WLAN_08

PassedTo verify whether theclient link is enabledin AP1600.

Check the status of clientlink in AP1600

WLJ80S_WLAN_09

PassedTo verify whetheropen authenticationSSID is able to createon both radios in1262AP GUI and twoor more clients areable to associate withit and able tocommunicate betweenthem.

Configure a openauthentication SSID onboth radios in AP1262GUI and associate two ormore clients and pingbetween them

WLJ80S_WLAN_10

PassedTo verify whetheropen authenticationSSID is able to createon both radios in1262AP CLI and twoor more clients areable to associate withit and able tocommunicate betweenthem.

Configure a openauthentication SSID onboth radios in AP1262CLI and associate two ormore clients and pingbetween them

WLJ80S_WLAN_11


261


PassedTo verify whetherlayer 2 securityWLAN is able tocreate in wlc5508 GUIand able to associate50 clients to it.

Configure a Layer2security WLAN in wlc5508 GUI and asscoiate50 clients to it and check.

WLJ80S_WLAN_14

PassedTo verify whetherlayer 2 securityWLAN is able tocreate in wlc5508 CLIand able to associate50 clients to it.

Configure a Layer2security WLAN in wlc5508 CLI and asscoiate50 clients to it and check.

WLJ80S_WLAN_15

PassedTo verify whetherinternal DHCP serveris able to create inWLC and associate aclient and checkwhether it getting ipaddress from DHCPserver.

Configure a internalDHCP server inWLC andassociate a client bygetting ip address fromdhcp server

WLJ80S_WLAN_16

PassedTo verify whetherDHCP server is able toconfigure in AP andassociate a client andcheck whether itgetting ip address fromDHCP server.

Configure a DHCP serverin AP and associate aclient by getting ipaddress from DHCPserver.

WLJ80S_WLAN_17

PassedTo verify whetherlocal macauthentication is ableto configure and ableto associate client inAP1042

Configure a local MACauthentication in AP1042and associate clients

WLJ80S_WLAN_18

PassedTo verify whether macaddress authenticationis able to configureand able to associateclient in AP1042 withradius server.

Configure a Mac addressauthentication in AP1042with Radius server andassociate clients.

WLJ80S_WLAN_19

PassedTo verify whether theAP is configured aslocal radius serverwith EAP-LEAP andable to associateclients

Confiigure a AP as localradius server withEAP-LEAP security

WLJ80S_WLAN_20


262


PassedTo verify whether theclient is able toauthenticate andassociate with AP byusing radius server

Configure a autonomousAPwith Radius server forauthenticaiton

WLJ80S_WLAN_21

PassedTo verify whetherEAP-TLSauthentication withRadius server is ableto configure and ableto associate client withAP.

Configure EAP-TLSauthentication withRadius server andassociate clients.

WLJ80S_WLAN_22

PassedTo verify whether usercan able to login to theAutonoumous AP'sGUI successfully ornot via ACSAuthentication

TACACS Authenticaitonfor Autonomous AP

WLJ80S_WLAN_23

PassedTo verify whetherthere is anyIntermittentdisconnection in AP ornot

Radio Beacons andACKsfrom 1142 AP

WLJ80S_WLAN_24

PassedTo verify whether1142 AP can beupgraded from 12.4image version to 15.2successfully or not

1142 AP UpgradeWLJ80S_WLAN_25

PassedTo verify whetherclients are associatedsuccessfully or notafter WGB roaming

Client Roaming fromWGB AP1 to AP2

WLJ80S_WLAN_26

PassedTo verify whetherclients are associatedsuccessfully or notafter WGB roaming

Client Roaming backfrom WGB AP2 to AP1

WLJ80S_WLAN_27

PassedTo verify whetherWindows 7 clients cansuccessfully associateto WPA2 Securitywith AES encryptionor not

WPA2 Security with AESencryption in 1600Autonomous AP

WLJ80S_WLAN_28


263


PassedTo verify whetherApple MAC clientscan successfullyassociate to WPA2Security with AESencryption or not

WPA2 Security with AESencryption in 1600Autonomous AP

WLJ80S_WLAN_29

PassedTo verify whether thevoice traffic is gettinginterrupted or not afterroaming

Voice in 7921 SeriesWireless IP Phones - Intracontroller roaming

WLJ80S_WLAN_30

PassedTo verify whether thevoice traffic is gettinginterrupted or not afterroaming

Voice in 7921 SeriesWireless IP Phones - Intercontroller roaming

WLJ80S_WLAN_31

PassedTo verify whether theAP transmission isstopped or not duringmulticasting

Multicast traffic to andfrom wireless client

WLJ80S_WLAN_32

PassedTo verify whethersimultaneously paralleldownload could bedone in 1602 series APor not

Downloading via 1602Series Access Point

WLJ80S_WLAN_33

PassedTo verify whethersimultaneously parallelupload could be donein 1602 series AP ornot

Uploading via 1602 SeriesAccess Point

WLJ80S_WLAN_34

PassedTo verify whetherlarge config is saved tonvram successfully ornot

AP Buffer size - ACLConfig

WLJ80S_WLAN_35

PassedTo verify whetherlarge config is saved tonvram successfully ornot

AP Buffer size - Otherlarge Config changes

WLJ80S_WLAN_36

PassedTo verify whetherconfiguration changesor not after upgradingAP software

Upgrading theautonomous AP software

WLJ80S_WLAN_37

PassedTo verify whetherconfiguration changesor not after rebootingAP

Configuring 2600 seriesAutonomous AP'sinterface

WLJ80S_WLAN_38


264


PassedTo verify whetherconfiguration changesor not after rebootingAP

Configuring 3600 seriesAutonomous AP'sinterface

WLJ80S_WLAN_39

PassedTo verify whether theincremental config inActive WLC has beensynced to Standby HotWLC

Incremental config syncbetween Active andStandby Hot WLCs

WLJ80S_WLCHA_01

PassedTo verify whether thenew Active has all itsconfig restored afterswitchover happensdue to nw/hw failureof previous active

Config Check afterswitchover happens

WLJ80S_WLCHA_02

PassedTo verify whether APdoesn't log any errormessages(CapwapSN)when switchoverhappens between theWLC HA

AP logs when switchoverhappens in WLC HA

WLJ80S_WLCHA_03

PassedTo verify whether APfallback to primaryWLC when APfallback is enabledglobally

AP fallback to primarywhen AP fallback isenabled globally

WLJ80S_WLCHA_04

PassedTo verify whether APfallback happens whenAP fallback is disabledglobally

AP fallback to primarywhen AP fallback isdisabled globally

WLJ80S_WLCHA_05

PassedTo verify AP fallbackhappens when theWLCs are in samemobility group

AP fallback when theWLCs in same mobilitygroup

WLJ80S_WLCHA_06

PassedTo verify AP fallbackhappens when PrimaryWLC is configured asMaster WLC

AP fallbackwhen primaryWLC is configured asMaster WLC

WLJ80S_WLCHA_07


265


NECAnyconnect VPN


PassedTo check whether theAnyconnect VPN is connector not, using WPA+WPA2layer2 security in LaVie TabS business

WPA+WPA2network(AnyConnect)using LaVie Tab Sbusiness

WLJ80MRS_NEC_01

PassedTo check whether theAnyconnect VPN is connector not , using "None" Layer 2security in LaVie Tab Sbusiness .

Layer 2 security"None" for openauth network(Anyconnect) inLaVie Tab Sbusiness .

WLJ80MRS_NEC_02

PassedTo verify the intra controllerroaming within the samesubnet in LaVie Tab Sbusiness

Anyconnect VPN- Intra controllerroamingwithin thesame subnet inLaVie Tab Sbusiness

WLJ80MRS_NEC_03

PassedTo verify the inter controllerroaming using different subnetin LaVie Tab S business

Anyconnect VPN- Inter controllerroamingwithin thedifferent subnet inLaVie Tab Sbusiness

WLJ80MRS_NEC_04

L2 Security


PassedTo check whether theLaVie Tab S business isassociated successfully intothe network or not.

Associating LaVieTab S business - L2Security "None"

WLJ80MRS_NEC_05

PassedTo check whether theLaVie Tab S business isassociated successfully intothe network throughWPA2+PSK authenticationmethod

Associating LaVieTab S business -WPA2+PSK

WLJ80MRS_NEC_06


266

Regression Features - Test SummaryNEC


PassedTo check whether theLaVie Tab S business isassociated successfully intothe network or not with L2Security WPA2+Dot1x

Associating LaVieTab S business - L2Security"WPA2+Dot1x".

WLJ80MRS_NEC_07

L3 Security


PassedTo check whether theLaVie Tab S business isassociated successfully ornot into the networkthrough Web-Auth

Associating LaVieTab S business - L3security "Web-Auth"

WLJ80MRS_NEC_08

PassedTo check whether theLaVie Tab S business isassociated successfully ornot into the networkthrough Web-AuthPassthrough

Associating LaVieTab S business - L3security "Web-AuthPassthrough"

WLJ80MRS_NEC_09

Roaming


PassedTo verify whether LaVieTab S business client isconnected or not with FTenabled WLAN in 5760WLC.

Associating LaVieTab S business to aWLAN with FTenabled.

WLJ80MRS_NEC_10

PassedTo verify whether LaVieTab S business client isconnected or not withoutFT enabled WLAN in5760 WLC.

Associating LaVieTab S business to aWLAN without FTenabled.

WLJ80MRS_NEC_11

PassedTo verify whether LaVieTab S business client isroamed or not between 25760 WLC's.

Roaming LaVie TabS business clientbetween 2 5760WLC's with FTenabled &WPA2+PSk security.

WLJ80MRS_NEC_12


267




Roaming LaVie TabS business clientbetween 2 5760WLC's with FTenabled &WPA2+PSk security.

WLJ80MRS_NEC_13


Roaming LaVie TabS business clientbetween 2 5760WLC's with FTenabled&L2 security"None".

WLJ80MRS_NEC_14


Roaming LaVie TabS business clientbetween 2 5760WLC's with FTenabled&L2 security"None".

WLJ80MRS_NEC_15

Multiple RADIUS server per SSID


PassedTo verify whether theClient authentication isdone via PrimaryRADIUS serverconfigured inflexconnect group

LaVie Tab S businessassociation throughPrimary RADIUSserver(ISE) at sitelevel with L2 SecurityWPA2+Dot1x(PEAP)

WLJ80MRS_NEC_16

PassedTo verify whether theClient authentication isdone via SecondaryRADIUS serverconfigured inflexconnect group

LaVie Tab S businessassociation throughSecondary RADIUSserver(ISE)at site levelwith L2 SecurityWPA2+Dot1x(PEAP)

WLJ80MRS_NEC_17

PassedTo verify whether theClient authentication isdone via PrimaryRADIUS serverconfigured inflexconnect group

LaVie Tab S businessassociation throughPrimary RADIUSserver(ACS) at sitelevel with L2 SecurityWPA2+Dot1x(PEAP)

WLJ80MRS_NEC_18


268



PassedTo verify whether theClient authentication isdone via SecondaryRADIUS serverconfigured inflexconnect group

LaVie Tab S businessassociation throughSecondary RADIUSserver(ACS) at sitelevel with L2 SecurityWPA+Dot1x(PEAP)

WLJ80MRS_NEC_19

AAA


PassedTo check whetherregistered client issuccessfullyauthenticated andassociated with WLANenabled MAC Filtering

Performing MACFiltering with LaVieTab S businessregistered in ACSserver- 7500Controller

WLJ80MRS_NEC_20

PassedTo check whetherregistered client issuccessfullyauthenticated andassociated with WLANenabled MAC Filtering

Performing MACFiltering with LaVieTab S businessregistered in ISEserver- 7500Controller

WLJ80MRS_NEC_21

Client SSO


PassedTo verify whether theClient SSO is successfulwith L3 security typeweb-authentication inWLC 5508

Client SSOwith webauthentication L3Security-LaVie TabS business

WLJ80MRS_NEC_22

PassedTo validate Client SSOwith L3 security typeweb-auth after sessiontimeout

Client SSOwith webauthentication L3Security after sessiontimeout-LaVie TabS business

WLJ80MRS_NEC_23

PassedTo validate Client SSOwith L2 securityWPA/WPA2 (localswitching)

Client SSO with L2SecurityWPA/WPA2(localswitching)-LaVieTab S business

WLJ80MRS_NEC_24


269


H-REAP Fault tolerance


PassedTo verify whether theclient associated toflexconnect AP will getreassociated in case offault tolerance


WLJ80MRS_NEC_25

PassedTo verify whether theclient associated toflexconnect AP will getreassociated in case offault tolerance

HREAP faulttolerance betweenstandalone andconnected AP-5GHZ

WLJ80MRS_NEC_26

Adhoc Test CasesDefectsStatusDescriptionTitleLogical ID

PassedTo check whether Nas-idunder Controller> general tabis present or not in OLH page.

Checking thedescription ofNas-ID underController> generalpage in OLH page.

WLJ80S_Failed_04

CSCun75576FailedTo Verify the analytics tabtake more time compare to theDashboard and reports Tab foraccessing.

Check theaccessibility foranalytics and othertab

WLJ80S_Failed_19

CSCun78279FailedTo verify the Zone basedanalytics for the multiple zonedisplays wrongly by selectingspecific zone on the specificdate. And it displays the zoneinstead selected zone. Theselected zone for analysis wasnot created on the date insteadit shows the another zone.

check the zonebased analytics forthe specific zone atspecific time

WLJ80S_Failed_21

PassedTo verify the building withcorresponding maps changedafter reset analytics.

Check whetheranalytics displaysbuilding withcorrespondingmapsafter reset

WLJ80S_Failed_27

CSCun76218FailedTo verify PI Maps issynchronized withMSEwhilecopying the exiting Maps

PI Maps is notsynchronized withMSEwhile copyingthe exiting Maps

WLJ80S_Failed_20


270

Regression Features - Test SummaryAdhoc Test Cases


CSCun78876FailedTo verify whether able toselect multiple date option forthe Zone analysis

Unable to selectmultiple date optionfor the Zoneanalysis

WLJ80S_Failed_26

CSCun78862FailedTo verify Deleted real path isdisplayed inmost popular pathanalysis

Deleted real path isdisplayed in mostpopular pathanalysis

WLJ80S_Failed_25

PassedTo checkwhether Page doesn’tget reset when changingclients max records in HTTPSmode of GUI

Page gets resetwhen changingclients max recordsin HTTPS mode ofGUI

WLJ80S_Failed_22

CSCun59052FailedTo verify whether applybutton works or not in VLANmapping page of FlexconnectAP

Checking the applybutton in VLANmapping page ofFlexconnect AP

WLJ80S_Failed_12

PassedTo verify whether errormessage is correct whileselecting save Eventnotification

Clicking save Eventnotification showswrong message

WLJ80S_Failed_15

PassedTo verify whether Station roleis shown as "Unknown" inAutonomous AP GUI forspectrum mode

Station role isshown as"Unknown" inAutonomous APGUI for spectrummode

WLJ80S_Failed_36

PassedTo verify Add/Update ZoneDescription is not stored in theMaps tab

Add/Update ZoneDescription is notstored in the Mapstab

WLJ80S_Failed_38

PassedTo verify Inheritance level forall WLAN entries changed toAP in Central DHCP page

Inheritance level forall WLAN entrieschanged to AP inCentral DHCP page

WLJ80S_Failed_24

PassedGUI : To verify WLANProfile name mismatch inWLAN VLAN mapping tabof flex group

GUI : WLANProfile namemismatch inWLAN VLANmapping tab of flexgroup

WLJ80S_Failed_06


271



PassedTo verify whether it is able tochange the Access mode inSNMP community from theWLC GUI

Unable to changethe Access mode inSNMP communityfrom theWLCGUI

WLJ80S_Failed_10

PassedTo verify HA works fine withuntagged management vlanafter upgraded to 8.0

HAworks fine withuntaggedmanagement vlanafter upgraded to8.0

WLJ80S_Failed_05

PassedTo verify AP CLI acceptsprimary and secondarycontroller as same server

AP CLI acceptingprimary andsecondarycontroller as sameserver

WLJ80S_Failed_42

PassedTo verify IP address reversedfor NTP server in 8500 WLCGUI

IP address reversedfor NTP server in8500 WLC GUI

WLJ80S_Failed_01

CSCup56865FailedTo verify PI CLI afterchanging hostname/IP uponre-setup

Unable to login PICLI after changinghostname/IP uponPI re-setup

WLJ80S_Failed_51

CSCuo37342FailedTo verify whether Device PortSummary dashlet showswrong info for controllers

Device PortSummary dashletshows wrong infofor controllers

WLJ80S_Failed_43

CSCup59088FailedTo verify whether CLIdescription for module3G isappropriate

CLI description ismissing formodule3G incommand "configap ?"

WLJ80S_Failed_46

CSCup86941FailedTo verify Policy Type forStatic WEP clients in WLCGUI - (No Config)

Policy Type forStatic WEP clientsin WLC GUI - (NoConfig)

WLJ80S_Failed_54

CSCuq82767FailedTo verify the Systemconfiguration under Softwaretab in AP GUI

SystemConfiguration ofAP in AP GUI

WLJ80S_Fail_02

CSCuq89168FailedTo check the LED flash statedescription in OLH page

LED Flash statedescription ismissing in OLHpage for All APsdetails

WLJ80S_Fail_03


272



CSCuq94587FailedTo verify whether WLCaccepts EAP profile name asUTF-8 character and displayit as it is. To verify whetherWLC accepts EAP profilename as UTF-8 character anddisplay it as it is.

EAP profile namedisplay as Junkcharacter if createdin UTF-8 character

WLJ80S_Fail_06

CSCur00347FailedTo check the VLAN status inauto AP cli

Deleted VLAN isshowing inAutonomous APCLI.

WLJ80S_Fail_08

CSCuq93760FailedTo verify whether webauth aclcould be configured withoutdeactivating Custom webauthin AAP

Custom Webauthand Webauth ACLconfig in AAP

WLJ80S_Fail_10

CSCur08583FailedTo verify whether AP clidisplays the output for thecommand show capwap clientconfig

AP CLI:showcommand innon-privilegedmode

WLJ80S_Fail_11

CSCur12267FailedTo verify whether the WLCdoesn’t accept wlan profile andssid name as empty

Creating WLANprofile and SSIDnames as emptygets accepted inCLI

WLJ80S_Fail_12

CSCun55413FailedTo verify whether NGWCconfiguration via Systemconfig dialog

NGWCconfiguration viaSystem configdialog

WLJ80S_Failed_11

CSCum84944FailedTo verify whether no optionsare missing in WLAN>Advanced> Flexconnect inOLH page

Some optionsmissing inWLAN>Advanced>Flexconnect inOLH page

WLJ80S_Failed_02

CSCun96815FailedTo verify whether OEAPACL's & Network lists getsdeleted after upload/downloadthe config

OEAP ACL's &Network lists getsdeleted after upload/download theconfig

WLJ80S_Failed_31

CSCus60566FailedTo verify whether Hangouts(Gtalk) messenger in AVC isblocked

Unable to block theHangouts (Gtalk)messenger in AVC

WLJ80MRS_Failed_01


273



CSCus68028FailedTo verify whether Gmailworks in android client whengmail application WLC isblocked in AVC

Gmail works inAndroid Clientwhen GmailapplicationWLC isblocked in AVC

WLJ80MRS_Failed_02

Related DocumentationACS Installation Guide

http://www.cisco.com/en/US/partner/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/introd.html

ISE User Guide

http://www.cisco.com/en/US/docs/security/ise/1.2/user_guide/ise_overview.html

PI 2.0 User Guide

http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-0/user/guide/prime_infra_ug.pdf

WLC 7.6 Configuration Guide

http://www.cisco.com/c/dam/en/us/td/docs/wireless/controller/7-6/configuration/guide/b_cg76.pdf

MSE Reference Guide

http://www.cisco.com/en/US/docs/wireless/mse/3310/quick/guide/MSE3310_GSG.html

CT5760 Controller Deployment Guide

http://www.cisco.com/en/US/docs/wireless/technology/5760_deploy/Supported_Features.html

Cisco Catalyst 3850 Switch Deployment Guide

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps12686/deployment_guide_c07-727067.html


274

Regression Features - Test SummaryRelated Documentation



http://www.cisco.com/en/US/docs/security/ise/1.2/user_guide/ise_overview.html

http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-0/user/guide/prime_infra_ug.pdf

http://www.cisco.com/c/dam/en/us/td/docs/wireless/controller/7-6/configuration/guide/b_cg76.pdf

http://www.cisco.com/en/US/docs/wireless/mse/3310/quick/guide/MSE3310_GSG.html

http://www.cisco.com/en/US/docs/wireless/technology/5760_deploy/Supported_Features.html

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps12686/deployment_guide_c07-727067.html

Date post:	22-May-2020
Category:	Documents
Upload:	others
View:	22 times
Download:	0 times

Test Results Summary for Cisco Wireless LAN Controller ... · WLC-License213 AP-GUI215...

Documents