the new Govt. Medical College at Balasore, Odisha VOLUME...

AN ISO 9001 & 14001 COMPANY

TENDER DOCUMENT

TENDER NO: WRO/CON/030-B/0215

Tender for “Electrical Work for Teaching Hospital for

the new Govt. Medical College at Balasore, Odisha

VOLUME – III

PRICE BID/BILL OF QUANTITY (BOQ)

Total Amount( Rs.)

1 2 3 4 5= (3 x 4 ) 3 + 5

In figures In words In figures In words

2 ELECTRICAL WORKS 144015315.00

Total 144015315.00

Note:

1. Rates to be quoted in this tender all inclusive with all taxes and duties etc. Excluding GST.

2.The bidder has to quote above/below percentage (%) Excluding GST However, the percentage (%) of GST applicable is to be shown separately

for reference

BIDDERS FINANCIAL OFFER:

(In Figures)__________________________________________________________________________________________________

(In Words)___________________________________________________________________________________________________

PRICE SCHEDULE

Tender for “Electrical Work for Teaching Hospital for the new Govt. Medical College at Balasore, Odisha”

SI. No. DESCRIPTION ESTIMATED COST (Rs.)

TO BE QUOTED BY TENDERER

% ( - ) Below / At Par/AboveAmount In INR

NIT No. WRO/CON/B-04/030-B/

Sign and stamp of EPIL 1 Sign and stamp of bidder

Sl.

No.Item Description Quantity Units

Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

ELECTRICAL

1139 HVAC Work

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of

following size direct in ground including excavation, sand cushioning, protective covering and

refilling the trench etc as required.

1140 Laying of MV XLPE Cable upto 35 sq. mm in ground 2362.00 Mtr 216.90 512317.80

1141 Above 35 sq. mm and upto 95 sq. mm in ground 1.00 Mtr 223.20 223.20

1142 Laying of Above 95 sq. mm and upto 185 sq. mm XLPE power cable of 1.1 kV grade direct in

ground

40.00 Mtr 228.60 9144.00


ground

240.00 Mtr 246.60 59184.00

1144 1.1 kV L.T CONTROL CABLE LAYING 0.00 0.00

1145 1.1 kV L.T Cable Laying of one number armoured XLPE insulated and PVC sheathed control

cable 1.1 kV of following size in the existing cable Trays/ Surface including providing suitable

size clamp to secure the cable in tray/ surface as required.

0.00 0.00

1146 4 core, 7 core, 2.5 Sq.mm. Cu. Conductor cable 800.00 Metre 31.50 25200.00

1147 Supplying and making end termination with brass compression gland and aluminium lugs for

following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

0.00 0.00

1148 3.5 core, 240 Sq.mm.-Alumiium Cable 12.00 Sets 458.10 5497.20

1149 3.5 core, 150 Sq.mm.-Alumiium Cable 4.00 Sets 595.80 2383.20

1150 3 core, 35 Sq.mm.-Alumiium Cable 1.00 Sets 166.50 166.50



1153 3 core, 10 Sq.mm.-Copper Cable 20.00 Sets 121.50 2430.00

1154 3 core, 6 Sq.mm.-Copper Cable 94.00 Sets 100.80 9475.20

1155 3 core, 4 Sq.mm. -Copper Cable 206.00 Sets 100.80 20764.80

1156 EARTHING 0.00 0.00

1157 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

required.

800.00 Metre 249.30 199440.00

1158 Providing and fixing 6 SWG dia G.I. wire on surface or in recess 250.00 Metre 23.40 5850.00

1561 ELECTRICAL WORKS WITH HVAC SYSTEM

MAIN HVAC PANEL (MCC-1)

Tender for “Electrical Work for Teaching Hospital for the new Govt. Medical College at Balasore, Odisha”

NIT No. WRO/CON/B-04/030-B/


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1562 Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of motor

control centre, which shall be fabricated out of 2mm thick CRCA sheet steel in form in 3b

formation with reinforcement of suitable size angle iron, channel ‘T’ sections irons and/or flats

wherever necessary. Cable gland plates shall be provided on top as well as at the bottom of the

panels. Panels shall be treated with all anticorrosive process before painting as per

specifications with 2 coats of red oxide primer and final approved shade of powder coated

paint. 2 No. earthing terminals shall be provided for 3 phase, 415 V, 4 wire, 50 Hz supply

system. Lifting hooks shall also be provided in case of large panels. Approval shall be taken for

each panel before fabrication. Cadmium Plated hardware shall be used in fabrication of panels.

All outgoing & incoming shall be provided with Stop/Manual/ Auto/selector switch to facilitate

operation through BAS. All starters shall be provided with potential free Contact for

Connections to Building Automation System.

1563 A separate set of CTs to be provided for BAS and wiring from CT’s and voltage transducers to

be brought on to separate set of terminals.

Incoming-1&2

1 No. 630 amps TP+N, Ics 50 kA , moudle one circuit breaker with microprocessor release unit

having following protection;

• Overload

• Short circuit

ON / OFF indicating lamps with control 6A MCB etc.

Metering & Indication (for each ACB)

1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.

1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 6A SP MCB

1 No. (0-630A) Ammeter with ASS with 3 nos. 1000/5A CT's, 15VA

1 Set- of ON/OFF indicating lamps.

3 Nos. 630A/5A, 15VA CTs.

Bus Bars

800 amps TPN , 100 kA for 1 sec. ,Aluminium bus bars with colour coded heat shrinkable

insulating sleeves - 1 Set.

Outgoing


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1564 3 No. 630 amps TPN MCCB of 50kA , as Feeder for feed to 3 No. (250 TR) each Water

cooled chilling unit compressor motor. The MCCB compartment shall contain CT operated

analouge ammeter of 0- 630 amps range with selector switch and 1 set of ON/OFF/TRIP

indicating lamps protected with 3 nos. 6A SP MCBs of chiller motor.

3 No. 63 amps TPN MCCB of 50kA, Star Delta starters with over load relay with built in single

phasing protection and outgoing feeders to primary chilled water pump motors including

standby. Each of these compartment shall contain CT operated analouge ammeter of 0-63

amps range with selector switch, and 1 set of ON/OFF/TRIP indicating lamps protected with 3

nos. 6A SP MCBs of Pump motors.

2 Nos. 150 amps TPN MCCB of 50 kA for 2 Nos. motor outgoing feeders to Adjustable

Frequency Drive (AFD) panel zone (A) & outgoing feeder to Secondary Chilled water pump

motors (1 working + 1 standby) The compartments shall contain CT operated analouge

ammeter 0 - 150 amps range with selector switch and 1 set of ON/OFF/TRIP indicating lamps

protected with 3 nos. 6A SP MCBs of Pump motors. 1565 3 No.100 amps TPN MCCB of 50kA , star delta starters, over load relay with built in single

phasing protection and outgoing feeders to Condensor water pump motors including standby.

Each of these compartment shall contain CT operated analouge ammeter of 0-100 amps range

with selector switch,and 1 set of ON/OFF/TRIP indicating lamps protected with 3 nos. 6A SP

MCBs of Pump motors.

40 amps TPN MCCB of 65kA , 6 Nos. motor outgoing feeders to Adjustable Frequency Drive

(AFD) panel zone (A) & outgoing feeder to cooling tower Fan motors . The compartments shall

contain CT operated analouge ammeter 0 - 40 amps range and 1 set of ON/OFF/TRIP

indicating lamps protected with 3 nos. 6A SP MCBs of Pump motors.

Necessary internal wiring, control wiring shall also be included. All switches and other

components shall be motor duty rating.

1566 Mian HVAC Panel as described above. 1.00 No. 1310458 1310458.00

1567 HVAC PANEL FOR HEAT PUMP & ASSOCIATED PUMPS (TERRACE)

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of motor

control centre, which shall be fabricated out of 2mm thick CRCA sheet steel in form in 3b

formation with reinforcement of suitable size angle iron, channel ‘T’ sections irons and/or flats

wherever necessary. Cable gland plates shall be provided on top as well as at the bottom of the

panels. Panels shall be treated with all anticorrosive process before painting as per

specifications with 2 coats of red oxide primer and final approved shade of powder coated

paint. 2 No. earthing terminals shall be provided for 3 phase, 415 V, 4 wire, 50 Hz supply

system. Lifting hooks shall also be provided in case of large panels. Approval shall be taken for

each panel before fabrication. Cadmium Plated hardware shall be used in fabrication of panels.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1568 All outgoing & incoming shall be provided with Stop/Manual/ Auto/selector switch to facilitate

operation through BAS. All starters shall be provided with potential free Contact for

Connections to Building Automation System.

A separate set of CTs to be provided for BAS and wiring from CT’s and voltage transducers to

be brought on to separate set of terminals.

Design, manufacture, supply, installation, testing and commissioning of the following cubicle

type, wall mounted control panels including anchoring into the wall, wiring and earthing

terminating into MPCB in each panel shall be provided by the electrical contractor.

All outgoing shall be provided with Stop / Manual /Auto selector switch to facilitate operation

through BAS. All starters shall be provided with potential free Contact for Connections to

Building Automation System.

0 0.00

1569 MCB with over-load relay, suitable for motor duty and able to withstand fault level of 16 KA.

single phase preventer (Electronics type) as per the ratings given below.

Terminal block for power distribution.

Power Contactor.

Phase indicating lights and indicating light for ON/OFF/TRIP status phase sequence relay shall

also be provided.

Incoming

150 Amp TPN MCCB as incomer with following accessories:

0 - 500 volts 96 x 96 sq mm digital voltmeter with selector switch

0 - 150 amps 96 x 96 sq mm analouge ammeter with 3 Nos. 150/ 5 amps CT’s and selector

switch.

Phase indicating light shall be protected by MCB.

Bus bar

200 amps TPN aluminium bus bar with heat shrinkable insulation sleeves

Outgoing

0 0.00

1570 2 No. 100 amps TPN MCCB of 65kA , as Feeder for feed to 1 No. 125kw Air Cooled Heat

Pump The MCCB compartment shall contain CT operated analouge ammeter of 0- 100 amps

range with selector switch and 1 set of ON/OFF/TRIP indicating lamps protected with 3 nos. 6A

SP MCBs of chiller motor.

0 0.00

1571 2 No. 63 amps TPN MCCB of 65kA, Star Delta starters with over load relay with built in single

phasing protection and outgoing feeders to Hot water pump motors including standby. Each of

these compartment shall contain CT operated analouge ammeter of 0-63 amps range with

selector switch, and 1 set of ON/OFF/TRIP indicating lamps protected with 2 nos. 6A SP MCBs

of Pump motors.



0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1572 Mian HVAC Panel as described above. 1.00 No. 129401 129401.00

1573 CONTROL PANELS FOR OT ROOM WITH HEAT RECOVERY UNIT







MCB with over-load relay, suitable for motor duty and able to withstand fault level of 16 KA.



Power Contactor.


also be provided.

Incoming




switch.


Bus bar


0 0.00

1574 Outgoing

1 No. 32 amp TPN MCB and outgoing feeder to 5 HP Motor for supply air fan with VFD.

Suitable rating starter required as a bypass arrangement in case of VFD failure.

1 No. 25 amp TPN MCB and outgoing feeder to 3 HP Motor for Exhaust fan with VFD. Suitable

rating starter required as a bypass arrangement in case of VFD failure.

16A TPN MCB with 2HP Three phase DOL starter with overload relay and single phase

preventer . Each of these compartment shall contain indicating lamp with ON/ OFF/ TRIP

status for Heat Recovery Room

63A TPN MCB with 2No 9Kw for outdoor units Three phase stardelta starter with overload

relay and single phase preventer . Each of these compartment shall contain indicating lamp

with ON/ OFF/ TRIP status.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1575 Notes:



All MCCB shall be of 25 KA breaking capacity.

Coordination/Integration with Surgeon control panel shall be in scope of OT AHU vendor.

Suitable exhaust arrangement within electrical panel shall be provided to avoid overheating.

Necessary internal wiring, control shall also be included. All switches and other components

shall be motor duty rating.

All MCCB shall be of 16 KA breaking capacity.



0 0.00

1576 Supply,installation, testing and commissioning of OT AHU panel as described above. 2.00 No. 186425 372850.00

1577 CONTROL PANELS FOR OPERATION ROOM AHU (recirculation)







MCCB with over-load relay, suitable for motor duty and able to withstand fault level of 16 KA.



Power Contactor.


also be provided.

0 0.00

1578 Incoming




switch.


Bus bar


0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1579 Outgoing

1 No. 40 amp TPN MCB and outgoing feeder to 5 HP Motor for supply air fan with VFD.

Suitable rating starter required as a bypass arrangement in case of VFD failure.

1 No. 32 amp TPN MCB and outgoing feeder to 3 HP Motor for Exhaust fan with VFD. Suitable

rating starter required as a bypass arrangement in case of VFD failure.

63A TPN MCB with 2No 9Kw for outdoor units Three phase stardelta starter with overload

relay and single phase preventer . Each of these compartment shall contain indicating lamp

with ON/ OFF/ TRIP status.

0 0.00

1580 Notes:

Necessary internal wiring, control shall also be included. All switches and other components

shall be motor duty rating.

All MCB / MCCB shall be of 16 KA breaking capacity.



0 0.00

1581 Supply,installation, testing and commissioning of OT AHU panel as described above. 5.00 No. 180942 904710.00

1582 CONTROL PANEL IN AIR HANDLING UNIT (VFD is Part of AHU)









Power Contactor.


also be provided.

96 mm x 96 mm digital voltmeter and ammeter with selector switches

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1583 Suitable rating starter required as a bypass arrangement in case of VFD failure.

Time delay relay for delayed automatic restart of air handling unit motor.(0-180 Sec).

Wiring for microswitch for starting / stopping the fan when fire damper closes / Power supply for

fire damper control panel.

For on/off/remote and local operation, 3 pole single throw switch shall be provided in each AHU

panel to facilitate override of the automatic operation.

All starters shall be provided with suitable potential free contract for connections to the Building

Automation System.

The number of AHU control panels shall be as follows.

0 0.00

1584 40A TPN MCB with 7.5 HP Three phase Motor with VFD. Each of these compartment shall

contain indicating lamp with ON/ OFF/ TRIP status of motors. (Cost of VFD is part of Panel)

1.00 No. 76763 76763.00

1585 40A TPN MCB with 5 HP Three phase Motor with VFD. Each of these compartment shall


6.00 No. 71280 427680.00

1586 32A TPN MCB with 3 HP Three phase Motor with VFD. Each of these compartment shall


8.00 No. 65797 526376.00

1587 25A TPN MCB with 1.5/2 HP Three phase Motor with VFD. Each of these compartment shall


28.00 No. 63604 1780912.00

1588 16A TPN MCB with 0.75/1 HP Three phase Motor with VFD. Each of these compartment shall

contain indicating lamp with ON/ OFF/ TRIP status of motors.(Cost of VFD is part of Panel)

1.00 No. 61411 61411.00

1589 CONTROL PANELS FOR FAN SECTIONS,INLINE FANS & AXIAL FANS







Over-load relay, suitable for motor duty and able to withstand fault level of suitable KA rating.



Power Contactor.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1590 Phase indicating lights and indicating light for ON/OFF/TRIP status phase sequence relay shall

also be provided.

96 mm x 96 mm voltmeter and ammeter.

Time delay relay for delayed automatic restart of motor (0-180 sec).

Wiring for microswitch for starting / stopping the fan (in case of fire) / Power supply for damper

control panel.

For on/off/remote and local operation, 3 pole single throw switch shall be provided in each



Automation System.

The number of control panels shall be as follows.

0 0.00

1591 100A TPN MCCB with 20HP Three phase star delta starter with overload relay and single

phase preventer . Each of these compartment shall contain indicating lamp with ON/ OFF/

TRIP status for fan sections/axial fans.

1.00 No. 46058 46058.00

1592 63A TPN MCCB with 15 HP/12.5HP Three phase star delta starter with overload relay and

single phase preventer . Each of these compartment shall contain indicating lamp with ON/

OFF/ TRIP status for fan sections/axial fans.

5.00 No. 43865 219325.00

1593 63A TPN MCCB with 10 HP Three phase star delta starter with overload relay and single



1.00 No. 43865 43865.00

1594 40A TPN MCB with 7.5 HP Three phase DOL starter with overload relay and single phase


status for fan sections/axial fans.

16.00 No. 19739 315824.00

1595 40A TPN MCB with 5 HP / 5.5 HP Three phase DOL starter with overload relay and single



7.00 No. 19739 138173.00

1596 32A TPN MCB with 3HP Three phase DOL starter with overload relay and single phase


status for fan sections/axial fans.

22.00 No. 19739 434258.00

1597 25/16A TPN MCB with 0.5 to 2HP Three phase DOL starter with overload relay and single



24.00 No. 19739 473736.00

1598 CONTROL PANEL FOR AIR WASHER & SCRUBBER


type, dead front, sheet steel, wall mounted control panels including anchoring into the wall,

wiring and earthing terminating into MPCB in each panel shall be provided by the electrical

contractor.




0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1599 single phase preventer (Electronics type) as per the ratings given below.


Power Contactor.


also be provided.

96 mm x 96 mm digital voltmeter and ammeter with selector switches.

Time delay relay for delayed automatic restart of air handling unit motor.(0-180 Sec).

Wiring for microswitch for starting / stopping the fan when fire damper closes / Power supply for

fire damper control panel.

For on/off/remote and local operation, 3 pole single throw switch shall be provided in each AHU



Automation System.

The number of control panels shall be as follows.

0 0.00

1600 100A TPN MCCB with 15 HP Three phase star delta starter with overload relay and single


TRIP status for fan air washer.

1.00 No. 46058 46058.00



TRIP status for air washer pump

1.00 No. 19739 19739.00

1602 40A TPN MCCB with 10 HP Three phase DOL starter with overload relay and single phase


status for fan air washer.

1.00 No. 28512 28512.00



TRIP status for air washer pump

1.00 No. 19739 19739.00

1604 100 A TPN MCCB with 20 HP Three phase star delta starter with overload relay and single


TRIP status for Scrubber.

1.00 No. 52637 52637.00

1605 4 No. 6amp switch for modules for scrubber

Supply of XLPE insulated and PVC sheathed Aluminium conductor armoured cable of 1.1 KV

grade confirming to IS : 7098:1988 with upto date amendments of following sizes

0 0.00

1606 3.5 core, 240 Sq.mm. 240.00 Mtr 768 184320.00

1607 3.5 core, 150 Sq.mm. 40.00 Mtr 362 14480.00

1608 3 core, 35 Sq.mm. 1.00 Mtr 144 144.00

1609 3 core, 25 Sq.mm. 160.00 Mtr 81 12960.00

1610 3 core, 16 Sq.mm. 1.00 Mtr 64 64.00

1611 Supply of XLPE insulated and PVC sheathed copper conductor armoured cable of 1.1 KV


0 0.00

1612 3 core, 10 Sq.mm. 280.00 Mtr 68 19040.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1613 3 core, 6 Sq.mm. 890.00 Mtr 122 108580.00

1614 3 core, 4 Sq.mm. 1030.00 Mtr 125 128750.00

1615 Supplying of following sizes of 1.1 kV grade PVC insulated copper conductor armoured

stranded Control Cable conforming to IS :1554 complete as required and as per specifications.

0 0.00

1616 4C x 2.5 Sq. mm 400.00 Mtr 122 48800.00

1617 7C x 2.5 Sq. mm 200.00 Mtr 191 38200.00

1618 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray

(galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in

convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders

including G.I. bolts & nuts, etc. as required.

0 0.00

1619 100 mm width x 50mm depth x 1.6 mm thickness. 300.00 RM 559 167700.00




“bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in



0 0.00

1623 100 mm width x 50mm depth x 1.6 mm thickness. 5.00 Each 778 3890.00




“Tee” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in



0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)




1630 E.I. WORK

DISTRIBUTION BOARDS

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board,

240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din

bar, interconnections, powder painted including earthing etc. as required. (But without

MCB/RCCB/Isolator)

0 0.00

1631 6 way, Double door 6.00 Each 840 5040.00




Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1634 Supplying and fixing following way, horizontal type threSupplying and fixing following way,

horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/

recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/

Isolator)

0 0.00

1635 4 way (4 + 12), Double door 1.00 Each 1962 1962.00




1639 Supplying and fixing 5 amps to 32 amps rating, 240 volts, 'C' series, miniature circuit breaker

suitable for inductive load of following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

0 0.00

1640 Single pole 3284.00 Each 409 1343156.00

1641 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

required.

961.00 Each 14 13454.00

1642 Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

0 0.00

1643 40 amps 54.00 Each 247 13338.00

1644 63 amps 322.00 Each 298 95956.00

1645 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB


0 0.00

1646 40 amps 18.00 Each 534 9612.00

1647 63 amps 99.00 Each 556 55044.00

1648 Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual

current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB


0 0.00

1649 40 amps 54.00 Each 1713 92502.00

1650 63 amps 322.00 Each 1977 636594.00

1651 HT AND LT CABLES

Laying of one number XLPE power cable of 33 kV grade of following size direct in ground

including excavation, sand cushioning, protective covering and refilling the trench etc. as

required.

0 0.00

1652 Above 120sqmm and upto 400 Sq.mm. 230.00 M 518 119140.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1653 1.1 kV L.T Cable Laying of one number armoured XLPE insulated and PVC sheathed control

cable 1.1 kV of following size in the existing cable Trays/ Surface including providing suitable

size clamp to secure the cable in tray/ surface as required.

0 0.00

1654 4 core, 7 core, 12 core & 19 core, 2.5 Sq.mm. Cu. Conductor cable 3395.00 M 217 736715.00

1655 Above 35 sq. mm and upto 95 sq. mm in ground 2273.00 Mtr 223 506879.00


ground

2878.00 Mtr 229 659062.00


ground

8335.00 Mtr 247 2058745.00

1658 Laying and fixing of following sizes of one number PVC insulated and PVC sheathed/XLPE

Power cable of 1.1kv grade on cable tray as required.

0 0.00

1659 Upto 35 sq. mm (clamped with 1mm thick saddle) 8000.00 Mtr 32 256000.00

1660 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm

MS flat clamp)

622.00 Mtr 80 49760.00

1661 Laying of MV XLPE Cable 95 sq. mm to 185 sq. mm on cable tray 8000.00 Mtr 95 760000.00

1662 Laying of MV XLPE Cable 185 sq. mm to 400 sq. mm on cable tray 622.00 Mtr 132 82104.00

1663 Supplying and making end termination with brass compression gland and aluminium lugs for

following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

0 0.00

1664 3.5core, 300 Sq.mm. 16.00 Sets 500 8000.00

1665 3.5core, 240 Sq.mm. 20.00 Sets 458 9160.00

1666 3.5 core, 185 Sq.mm. 10.00 Sets 387 3870.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1667 3.5 core, 150 Sq.mm. 8.00 Sets 596 4768.00

1668 3.5 core, 120 Sq.mm. 16.00 Sets 185 2960.00

1669 3.5 core, 95 Sq.mm. 6.00 Sets 236 1416.00

1670 3.5 core, 70 Sq.mm. 52.00 Sets 203 10556.00

1671 3.5 core, 50 Sq.mm. 10.00 Sets 167 1670.00

1672 4 core, 35 Sq.mm. 14.00 Sets 167 2338.00

1673 4 core, 25 Sq.mm. 26.00 Sets 145 3770.00

1674 3 core, 25 Sq.mm. 4.00 Sets 143 572.00

1675 4 core, 16 Sq.mm. 200.00 Sets 142 28400.00

1676 3 core, 16 Sq.mm. 20.00 Sets 140 2800.00

1677 4 core, 10 Sq.mm. 1100.00 Sets 128 140800.00

1678 3 core, 10 Sq.mm. 60.00 Sets 122 7320.00

1679 Supplying and making end termination with double brass compression gland and Copper lugs

for following size of PVC sheathed copper conducter armoured control cable of 1.1 kV grand as

required.

0 0.00

1680 4 core, 6 Sq.mm. 52.00 Sets 102 5304.00

1681 3 core, 6 Sq.mm. 46.00 Sets 101 4646.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1682 EARTHING 0 0.00

1683 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing

masonry enclosure with cover plate having locking arrangement and watering pipe etc. with

charcoal/coke and salt as required.

47.00 Set 3291 154677.00

1684 Earthing with GI earth plate 600mm x 600mm x 6.0mm thick including accessories and

providing masonary enclosure with cover plate having locking arrangement and watering pipe

etc. (but without charcoal and salt) complete as required.

52.00 Set 2931 152412.00

1685 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and

providing masonry enclosure with cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

65.00 Set 4947 321555.00

1686 Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth

electrode, including connection/ termination with GI thimble etc. as required.

8.00 KG 22 176.00

1687 Supplying and laying 6 SWG G.I. wire tie with cable as required. 6000.00 RM 23 138000.00

1688 Supplying and laying Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for

connections etc. as required.

2700.00 RM 249 672300.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1689 Supplying and laying Providing and fixing 50 mm X 6 mm G.I. strip on surface or in recess for


1200.00 RM 311 373200.00

1690 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth

electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.

(Jointing shall be done by overlapping and with 2 Set of G.I. nut bolt & spring washer spaced at

50mm)

40.00 RM 77 3080.00

1691 LIGHTNING ARRESTOR 0 0.00

1692 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube,

having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc.

complete as required

35.00 Each 250 8750.00

1693 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning

conductor complete as required.(For horizontal run)

950.00 Meter 51 48450.00

1694 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning

conductor complete as required. (For vertical run)

925.00 Meter 79 73075.00

1695 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4

Nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

35.00 Each 55 1925.00

1696 Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as

required.

725.00 Meter 97 70325.00

1697 INTERNAL WIRING: 0 0.00

1698 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed steel conduit, with modular

switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable etc. as required.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1699 Group C 2335.00 Point 730 1704550.00

1700 Wiring for light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in

surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and

earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc.

as required.

0 0.00

1701 Primary point cntrld by SP MCB 34.00 Point 756 25704.00

1702 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point

(without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single

core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS

PVC insulated copper conductor single core cable etc. as required.

0 0.00

1703 Group C 3487.00 Point 1306 4554022.00

1704 Wiring for group controlled (looped) light point with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5

sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

0 0.00

1705 Secondary point cntrld by SP MCB 182.00 Point 1299 236418.00

1706 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core

cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper

conductor single core cable for loop earthing as required.

220.00 meter 140 30800.00

1707 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

0 0.00

1708 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 21529.00 meter 107 2303603.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1709 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 11049.50 meter 125 1381187.50

1710 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 8527.50 meter 158 1347345.00

1711 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 1045.00 meter 212 221540.00

1712 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess

including painting in case of surface conduit, or cutting the wall and making good the same in

case of recessed conduit as required.

0 0.00

1713 20 mm 11026.00 meter 86 948236.00

1714 25 mm 56513.00 meter 94 5312222.00

1715 32 mm 3537.00 meter 121 427977.00

1716 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in

surface/recess including cutting the wall and making good the same in case of recessed

conduit as required.

0 0.00

1717 20 mm 4631.00 meter 42 194502.00

1718 25 mm 39212.00 meter 47 1842964.00

1719 32 mm 408.00 meter 61 24888.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1720 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in

recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular

switch, connections etc. as required.

964.00 Each 320 308480.00


recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/ 6 A

modular switch, connections etc. as required. (For light plugs to be used in non residential

buildings).

877.00 Each 548 480596.00


recess, including providng and fixing 3 Nos. 3 pin 5/6 A modular socket outlet and 3 Nos. 5/ 6 A

modular switch, connections etc. as required. (For light plugs to be used in non residential

buildings).

58.00 Each 870 50460.00


recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A

modular switch, connections etc. as required.

904.00 Each 519 469176.00


recess, including providing and fixing 2 No.6 pin 5/6 A & 15/16 A modular socket outlet and

15/16 A modular switch, connections etc. as required.

58.00 Each 844 48952.00


recess, including providing and fixing 3 No.6 pin 5/6 A & 15/16 A modular socket outlet and

15/16 A modular switch, connections etc. as required.

58.00 Each 1236 71688.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1726 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in

recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB,

“C” curve including connections, painting etc. as required.

110.00 Each 383 42130.00

1727 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including


79.00 Each 35 2765.00

1728 LIGHTING FIXTURES 0 0.00

1729 Supplying and fixing brass batten/ angle holder including connections etc. as required. 2.00 Each 167 334.00

1730 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard

length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable,

including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

984.00 Each 207 203688.00

1731 Installation of exhaust fan in the existing opening, including making good the damage,

connection, testing, commissioning etc. as required.

79.00 Each 256 20224.00

1732 Installation, testing and commissioning of Recessed Down Light/Surface Down Light /wall

Mounted LED fittings of all sizes upto 25W LED, complete with all accessories including


6081.00 Each 105 638505.00

1733 Installation, testing and commissioning of Recessed Down Light/Surface Down Light fittings of

all sizes above 25W and Upto 40W LED, complete with all accessories including connections

etc. as required.

6573.00 Each 196 1288308.00

1734 Installation, testing and commissioning of pre-wired, LED Tube Light fitting of all types,

complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections

with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as

required.

319.00 Each 98 31262.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1735 MATV,DATA & VOICE SYSTEM SYSTEM

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing

surface/ recessed steel/ PVC conduit as required.

1650.00 meter 21 34650.00

1736 Supplying and fixing following piano type switch/ socket on the existing switch box/ cover

including connections etc. as required.

0 0.00

1737 Telephone socket outlet 558.80 Each 77 43027.60

1738 TV antenna socket outlet 33.00 Each 83 2739.00

1739 Data socket outlet 947.00 Each 525 497175.00

1740 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for

modular switches in recess etc. as required.

0 0.00

1741 1 or 2 Module (75 mmX75 mm) 1535.60 Each 192 294835.20

1742 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable as per EIA in the existing surface/

recessed Steel/PVC Conduit as required.

0 0.00

1743 1 run of cable 49578.00 meter 89 4412442.00



1746 33kV METERING SYSTEM AND HT PANEL 0 0.00

1747 Supply, Installation, Testing and Commissioning of support for overhead line 152mmx152mm

and 13 meter long C pole of I.S. standard including base plate, welding, drilling of required

hole etc. complete as required. R.S.J pole standard weight 37.10 kg/per metre. Cost also

include the foundation RCC material of 1:6:8 ratio inclusing digging and backfilling complete

as required.

4.00 Set 24581 98324.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1748 Supply, Installation, Testing and Commissioning of stranded ACSR "DOG" Conductor Size :

6/4.72+7/1.57 mm Steel Reinforced (ACSR) confirming to IS:398-1976 ofapproved make,

stringing, making off complete with binding at existing insulator, jointing, jumpering, tearing off,

connecting etc. as required and clearing of obstacles (ifany) etc.

0.02 Km. 48070 961.40

1749 Supplying, Installation Testing and commissioning of 33kV Polymer Disc insulator (70KN) 6.00 No. 649 3894.00

1750 Supplying, Installation Testing and commissioning of 33kV Polymer Pint insulator (70KN) 6.00 No. 749 4494.00

1751 Supply, Installation, Testing and Commissioning of 33kV,10kA , 1-ph, Outdoor,

Gapless/Lightning/Surge Arrester complete with insulating base,Terminal connectors etc

complete for installation,Testing & commissioning.

3.00 No. 30488 91464.00

1752 Supply, Installation, Testing and Commissioning of 33kV 400A 3-Ph Gang Switch (Rocking

type Air Break Isolator) along with support insulators operating mechanism base channel down

pipe terminal connector and other acesseries complete as per IS :9921 (Pt. I to IV)or its latest

ammendment and TS Vol II.

1.00 Set 69473 69473.00

1753 Supply, Installation, Testing and Commissioning of 33kV Drop out fuse rated current

100A/200A/400A, complete with fuse carrier assembly,fuse base & Tube and mounted

arrangment as per IS :9385 (Pt. I to III) or as ammended from time to time and Tech sepc. VoI-

II .

1.00 Set 30832 30832.00

1754 Supply, Installation, Testing and Commissioning of MS Channel 100x50x6mm. 200.00 kg 151 30200.00

1755 Supply, Installation, Testing and Commissioning of MS angle 50x50x6 -4kg per meter 100.00 kg 125 12500.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1756 Supply, Installation, Testing and Commissioning of Outdoor Type Metering Cubical for 33kV

Mains Supply

1.00 Set 15676 15676.00

1757 Supply, Installation, Testing and Commissioning of 33kV/110V CVT (CT& PT for

metering)combind set 100A-50-25/1A for HT metering

1.00 Set 75857 75857.00

1758 33kV HT PANELS

Supply, Installation, Testing and Commissioning of indoor type floor mounted metal clad, 33

kV, 1250A VCB Panel with totally enclosed,expendable & electrically interlocked, horizontal

drawout, horizontal isolation type breaker as per IS 13118, as per specifications, having

capacities as mentioned below, single break, trip free mechanism, manually charged and

closing breaker suitable for use on 33kV, 3Phase, 50Hz A.C. supply with short circuit fault level

of 750 MVA, complete with self contained electrically interlocked rack in and rack out

0 0.00

1759 INCOMER - consisting of followings-

1250 Amp. TP VCB with earth switch.

1 No. 33kV/110Volts PT Class 0.5 accuracy and 200VA burden with 1 No. VA F (0-36 kV),

digital type, and protection HRC fuse for HT metering upto 15kV on incomer.

0 0.00

1760 1 No. 33kV/240Volts PT Class 0.5 accuracy and 200VA burden for incomming supply.

1 No. Microprocessor based numerical relay with O/L, E/F and highset S/C protection

compatible.

Breaker control switch

240 V AC spring charging motor

Set of ON/OFF/TRIP indicating lamps.

Clear lamp for Trip Circuit healthy supply.

0 0.00

1761 Microprocessor based numerical relay with O/L, E/F and highset S/C protection compatible .

Breaker control switch

240 V AC spring charging motor

Set of ON/OFF/TRIP indicating lamps.

Clear lamp for Trip Circuit healthy supply.

Aux. relays for Anti Pumping,Fault & indication.

Trip Circuit spervision relay.

0 0.00

1762 Individual alarm annunciator with 8 windows and buzzer, ACK, rest, test push button for

individual transformer faults and electrical faults in respective window.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1763 Dual core dual ratio 3 CTs 20/ 40/5A of 15VA burden and accuracy Class -0.5 for metering and

class 5P10 for protection.

1.00 No. 3008969 3008969.00

1764 Supply, Installation, Testing and Commissioning of earth truck for 33kV VCB panel 1.00 No. 91510 91510.00

1765 TRANSFORMERS

33/ 0.433 KV INDOOR TYPE TRANSFORMER

(Oil Filled TYPE WITH ON LOAD TAP CHANGE OVER)

0 0.00

1766 Supply, Installation, Testing and Commissioning of 1000 KVA 3 phase, 33 / 0.433 KV Out door

type oil filled type transformer copper wound with DNY II connection and neutral brought out for

earthing. The transformer shall be provided with (+) 5% and (-) 15% in step of 1.25% ON load

tap changer on HT side confirming to IS : 1180 - 2014 and ECBC-2017. HT side cable

termination box shall be suitable for 33 KV, 3 C x240mm2 XLPE cable and LT side cable

terminal box shall be suitable for terminating of 2500 A cables. The transformer shall be

supplied with all accessories complete as per specifications on all respect.

3.00 No. 1522889 4568667.00

1767 BATTERY CHARGER & BATTERIES

Supply, Installation, Testing and Commissioning of 24 V Battery Charger Capacity following

capacity batteries Battery Charger shall be solid state, full wave fully controlled bridge, input

suitable for single phase 230V AC suppply, conforming to degree of protection IP-42, Sheet

steel enclosure 14 SWG thick, with automatic voltage regulation, current limiting circuitary, auto

cut facility, smooth filter circuit switches, Ammeter & voltmeter on DC side, RYB indicating

lamps (LED type) on AC side complete in all respect with float and boost/ buck charging,

switchgear, earthing, powder coated painting etc as required.Suitable for 230 V, including DC

DB single phase +/- 10% AC, 50 Hz supply as per specifications

0 0.00

1768 180 AH 1.00 No. 65196 65196.00

1769 65 AH 1.00 No. 39639 39639.00

1770 SAFETY EQUIPMENTS

Supplying of Rubber hand gloves suitable for 33 kV.

1.00 Pair 1148 1148.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1771 Supplying and fixing of Shock treatment chart both in Regional, Hindi & English.and framed

with 5mm thick glass as required.

5.00 Each 3651 18255.00

1772 Supply & fixing HT danger notice plate of 250 mm x 200mm, made of mild steel sheet of at

least 2mm thick & vitreous enamelled white on both sides and with inscription in signal red

colour on front side as required. (33 kV)

5.00 Each 334 1670.00

1773 Supply & fixing MV danger notice plate of 200 mm x 150mm, made of mild steel sheet of at

least 2mm thick & vitreous enamelled white on both sides and with inscription in signal red

colour on front side as required.

5.00 Each 240 1200.00

1774 Supply of First aid box containing material as prescribed by St. John Ambulance brigade or

Indian Red Cross complete as required

1.00 Each 2921 2921.00

1775 Providing of Insulatiing mat 1 meter wide & 25mm thick to withstand 36kV dielectric strength as

per IS 5424- 1969

10.00 RM 2306 23060.00

1776 Providing of insulating mat 1 meter wide & 6mm thick to withstand 3.3kV dielectric strength as

per IS 5424- 1969

100.00 RM 1071 107100.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1777 Providing Single Line Diagram on 5mm thick Aluminium sheet in A0 Size duly laminated. 1.00 Each 2608 2608.00

1778 Providing Single Line Diagram on 5mm thick Aluminium sheet in A1 Size duly laminated. 1.00 Each 2416 2416.00

1779 LT PANELS

AUTO LOAD SHARING / SYNCHRONISING PANEL FOR HOSPITAL

Supply, Installation, Testing and Commissioning of Auto Load Sharing / Synhronising Cum LT

change Over Panel cubicle type, made out of 14 swg CRCA sheet steel, totally enclosed, IP 42,

protection free standing, floor mounting, dust and vermin proof,indoor, compartmentalised,

powder coated painting suitable for operation on 3 Phase and neutral, 415v, 50 Hz AC supply

system with busbars extensible on both sides, interconnections with 2.5mm2 size of FRLS

copper wire, control circuit with breaker control switch & auto/ manual selector switch, spring

charging indication, ammeter, ammeter selector switches voltmeter, voltmeter selector

switches, indicating lamps CT's, multifunction meters internally wired, interlocking and having

following incomer & Bus coupler Air circuit breakers and outgoing Air circuit breaker/ Moulded

case circuit breaker complete with releases for protection all as shown on drawing including

supply & installation complete as required items and as per specifications (Panels shall be of

TTA conforming to IEC 61439/1):

All ACBs shall have Ics=Icw for 1.0 secs for all ACBs

INCOMER :-

3 No.ACB, 1250 Amps, 80 kA, 4 Pole, Microprocessor release Motor wound spring charged

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1780 Each Incomer shall have one set of the following items:

Intelligent multi function digital meter with Capability of Disturbance Direction Detection, Sag &

Swell Monitoring with Waveform Capturing, Class of accuracy: 0.2S as per IEC62053-22,

Sampling Rate of 256 Samples/Cycle, Harmonics analysis upto 63rd order for Voltage &

Current, RS485 PORT & Dual Ethernet PORT

1 Set of Indication Lamps, LED type, R,Y,B with 2 Amp control MCB and breaker 'ON', 'OFF',

'TRIP' & spring charged lamps.

Breaker failure protection.

BUS BARS

3000 Amps TPN, 80 kA for 1 sec. Aluminiun bus bars with heat coloured shrinkable insulation

sleeve. - 1 Set

BUS COUPLER

1 Set of ACB, 1600 Amps, 80kA, 4 Pole, (EDO) without release with Electrical interlocking

arrangement with incomer breakers as per single line diagram, Motor wound spring charged

closing mechanism, horizontal Drawout type including Auxilary contactor & control MCB's. if

any.

0 0.00

1781 OUTGOING

4 No. ACB, 1600 Amps, 100kA, 4 Pole with microprocessor release Motor wound spring

charged closing mechanism (EDO), horizontal drawout type.

2 No.400 amps TP+N Moulded Case Circuit Breaker Ics= Icu 50 kA,with microprocessor

based release unit with ROH having following protection;

• Overload (adjustable thermal)

• Short-circuit (fixed magnetic )

6 Set each outgoing Indication Lamps, LED type, for RYB with 2 Amp control MCB& breaker

'ON', 'OFF', 'TRIP' lamps with 2 Amp control MCB.

6 Set LED Indication lamps, Push buttons, window annunciation fascia etc of required quantity

as per technical specifications.

Provision shall be made for connection for control cables.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1782 FOR MANUAL SYNCHRONIZING OPERATION (For Each DG set)

1 No - Double voltmeter analog type 0 - 500V

1 No - Double frequency meter analog type 45-55Hz

1 No - SynchroNocope analog type

1 No - Synchroning switch

1 No - Auto / Manual switch rotary

1 No - DG selectors switch (1 to 5) position

1 No - Check Synchronizing Relay

1 No. - Bright Lamp

1 No. - Dark Lamp

Control & Relay Panels for 3No. x 750 kVA DG Set

5set : Each DG Set comprising of the following :

Digital KWH Meter -

Digital KW Meter

Digital Power Factor Meter

Digital VAF Meter

Temperature Scanner

0 0.00

1783 Voltage Restrained over current & earth Fault Protection (51V/51N)

Current unbalance - 46

Loss of Excitation - 40

Reverse Power - 32

Under Power - 37

Under / Over Voltage - 27/59

Under / Over Frequency - 81

Thermal overload Protection - 49

Breaker failure Protection

High Speed Master Trip Relay - VAJH 13

Trip Circuit Supervision Relay

Numeric generator differential Bias % with dual adjustable slop with PS class CT’s on both side

of alternator.

Emergency Stop Push Button

Annunciator, 16 window with in Accept, Reset, Test & Mute

Hooter

Motorised Potentiometer for speed control

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1784 1 No: Door Switch

1 No: Space Heater - 100 Watt

Necessary Indicating Lamps

1 Set : Three Phase Indicating Lamps

Necessary Push Button

MCB - SP - as required

MCB - DP - As required

Five push buttons – start, stop, reset, test and accept.

Engine cranking relay.

Mains supply voltage sensing relay.

Vender shall provide suitable PLC for interlocking and Load management.

Vender shall provide 1000 VA UPS with 30Mint backup with dry type maintenance free battery.

Vender shall provide 24 DC battery charger suitable for panel.

The control wiring shall be operate at 24V DC.

Motorised Potentiometer for speed / voltage control shall be procured from DG manufacturer

only

Energry meter shall be provided in all outgoing

0 0.00

1785 DG Auto load sharing / Synchronising Panel -1 _ as described as above and as per

specification complete in all respects.

1.00 Set 4163317 4163317.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1786 MAIN LT CUM LT CHANGEOVER PANEL FOR HOSPITAL

Supply, Installation, Testing and Commissioning of Main LT Cum LT change Over Panel

cubicle type, made out of 14 swg CRCA sheet steel, totally enclosed, IP 42, protection free

standing, floor mounting, dust and vermin proof,indoor, compartmentalised, powder coated

painting suitable for operation on 3 Phase and neutral, 415v, 50 Hz AC supply system with

busbars extensible on both sides, interconnections with 2.5mm2 size of FRLS copper wire,

control circuit with breaker control switch & auto/ manual selector switch, spring charging

indication, ammeter, ammeter selector switches voltmeter, voltmeter selector switches,

indicating lamps CT's, multifunction meters internally wired, interlocking and having following

incomer & Bus coupler Air circuit breakers and outgoing Air circuit breaker/ Moulded case

circuit breaker complete with releases for protection all as shown on drawing including supply &

installation complete as required items and as per specifications (Panels shall be of TTA

conforming to IEC 61439/1):

All ACBs shall have Ics=Icw for 1.0 secs for all ACBs

0 0.00

1787 INCOMER :-

5 No.ACB, 1600 Amps, 80 kA, 4 Pole, Microprocessor release Motor wound spring charged

closing mechanism (EDO), horizontal Drawout type with all protection i/c Earth fault, reverse

On-screen display of measurements, Current : phase/neutral/earth, average, max, % loading,

seq components, Voltage : Phase, Line, Average.

Each Incomer shall have one set of the following items:

Intelligent multi function digital meter with Capability of Disturbance Direction Detection, Sag &

Swell Monitoring with Waveform Capturing, Class of accuracy: 0.2S as per IEC62053-22,

Sampling Rate of 256 Samples/Cycle, Harmonics analysis upto 63rd order for Voltage &

Current, RS485 PORT & Dual Ethernet PORT

5 Set of Indication Lamps, LED type, R,Y,B with 2 Amp control MCB and breaker 'ON', 'OFF',

'TRIP' & spring charged lamps.

Breaker failure protection.

BUS BARS


sleeve. - 1 Set

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1788 BUS COUPLER

2 Set of ACB, 1600 Amps, 100kA, 4 Pole, (EDO) without release with Electrical interlocking

arrangement with incomer breakers as per single line diagram, Motor wound spring charged

closing mechanism, horizontal Drawout type including Auxilary contactor & control MCB's. if

any.

6 Set Indication Lamps, LED type, for RYB with 2 Amp control MCB & breaker 'ON', 'OFF',

'TRIP' & spring charged lamps with2 Amp control MCB.

0 0.00

1789 OUTGOING

















0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1790 5 No.160 amps TP+N Moulded Case Circuit Breaker Ics= Icu 50 kA,with microprocessor












33 Set each outgoing Indication Lamps, LED type, for RYB with 2 Amp control MCB& breaker

'ON', 'OFF', 'TRIP' lamps with 2 Amp control MCB.

0 0.00

1791 Vender shall provide suitable PLC for interlocking and Load management for all incommers

and Buscouplers.

All outgoing shall have Energy meters with features like Class of accuracy: 1 as per IEC 62053-

22/21, Avg Volt, Avg Amp,Total active power & energy delivered as measured by the meter .

Potential free contact shall be provided to remote starting facilities of each starter through BAS.

The control wiring shall be operate at 24V DC.

Wiring with space heater, thermostat and control MCB’s shall be provided all vertical sections

of panel.

Suitable danger board shall be provided.

0 0.00

1792 Main LT Cum LT Change over Panel (NON Critical)_ as described as above and as per

specification complete in all respects.

1.00 Set 4882446 4882446.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1793 375 kVAR CAPACITOR PANEL FOR HOSPITAL

Supply, Installation, Testing and Commissioning of Automatic Power Factor Corrector Panel,

375 kVAR (2X100KVAR +2 x 50 kVAR +2 x 25 kVAR+2 x 12.5 kVAR) + active capacitors, 3ph,

415V, totally enclosed, free standing, floor mounting, dust and vermin proof, cubicle type to be

fabricated out of 14 guage CRCA Sheet steel, with provision for capacitor mounted inside the

panel with Busbars, interconnections, adequate number of louvers and powder coated with

approved shade including supply & installation of following components and as per technical

0 0.00

1794 INCOMER

1 No. ACB, 800 Amps, 80kA, 4 Pole with microprocessor release Manullay spring charged

closing mechanism (MDO), horizontal drawout type.

1 Set of 1250A 80kA TPN Aluminium conductor busbar.

1 Set of Digital Voltmeter of suitable range for 3 phase, 4 wirre operation with LED display and

built-in selector switch along with 2 Amp MCB for controlling.

1 Set of Indication Lamps (LED type)for R,Y,B with 2 Amp MCB for controlling and breaker

0 0.00

1795 OUTGOING

Capacitors should be rated for 525V AC

2 No. 100 kVAR Super heavy duty type units with 14% detune filter.

2 No. 50 kVAR Super Heavy Dutyheavy duty type units with 14% detuned filter

2 No. 25 kVAR Super Heavy Dutyheavy duty type units with 14% detuned filter

2 No. 12.5 kVAR Super Heavy Dutyheavy duty type units with 14% detuned filter

2 No. Capacitor duty contactor 250A for 100 kVAR with over load relays.

0 0.00

1796 2 No. 40 A TP+N 50kA MCCB with Microprocess release with adjustable inbuilt Over Load,

Short Circuit and Earth Eault protection with extended rotory handle

10 Set of Auxilary Control contractors.

10 Set of Start/Trip push buttons.

20 Set of Indicating lamps (LED type) for capacitor ON (Green) & capacitor OFF (Red)

10 Set A/M Selector Switch.

4 Set of Axial flow fans with thermostate.

0 0.00

1797 Complete in all respect including all interconnections from the bus bars to MCCB and MCCB to

contactor and contactor to terminal blocks of Capacitor. Automatic Switching "ON" and "OFF"

capacitor panel described as above

2.00 Set 892733 1785466.00

1798 MCC - 1 (DG Auxilary)

Design, manufacture, supplying fixing in position of the following front operated cubicle type,

front access, dead back, 2mm thick steel enclosed free standing, dust and vermin proof,

switchboard with IP42 protection with hinged and lockable doors complete with

interconnections, tinned copper crimping lugs, bonding to earth and painting, suitable for use at

415 volts, 3 phase 4 wire 50 Hertz system, and suitable for a fault level of 35 kA symmetrical at

415 volts.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1799 Incoming

2 No. 250 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based

release unit with overcurrent,inbuilt Earth Fault and short circuit with ROH having following

protection;

• Overload (adjustable microprocessor based)


2 No. 250 amps 4P AC-3 Contactor following :

0 0.00

1800 Bus Bars


sleeve. - 1 Set

0 0.00

1801 Outgoing

10 No. suitable rating MPCB for 2.5 KW DOL starter and outgoing feeder to DG Fan enclosure

Fan motor (including 1No. standby). Each compartment shall contain auto / manual selector

swtich and indicating / push button lamps with MCB for ON / OFF / TRIP of motor.

3 No. suitable rating MPCB for 1 KW DOL starter and outgoing feeder to DG Fan enclosure

Fan motor (including 1No. standby). Each compartment shall contain auto / manual selector

swtich and indicating / push button lamps with MCB for ON / OFF / TRIP of motor.

0 0.00

1802 MCC - 1_ described as above 1.00 Set 326147 326147.00

1803 DG Set & ACCESSORIES

Supply, installation, testing and commissioning of Diesel Generator Set comprising of 750 kVA

prime continuous (actual) rating raditor coolled diesel Engine in acoustic enclosure with rated

capacity of suitable BHP at 1500 RPM, direct electronic fuel injection type vertical 4 stroke,

12/16 cylinder, electronic governor, power command control module (PCC-3.3, Cummins or

equiv) along with base frame coupled to alternator capable of delivering true 750 kVA output at

47 Deg temprature (600 KW at 0.8 power factor) brushless type 415V, 50 Hz, self exciting

3.00 Set 4595279 13785837.00

1804 EXHAUST PIPE

Supply and fixing of following sizes of MS pipe as per IS 1239 for exhaust piping complete with

bends,supports,flanges welding etc.for exhaust of DG Set including painting, supplying &

wrapping 150 mm thick minral wool thick insulation of density 150 Kg per cubic meter on all

sides of Exhaust pipe with chicken mesh wrapping and clading with 22 SWG aluminium sheet

suitable for this installation complete as required including guide support, expansion joint, SS

bellows wherever required and as per specification.

0 0.00

1805 200 mm dia (NB) (6 mm thick) 130.00 M 3952 513760.00

1806 300 mm dia. (32 mm thick insulation) 90.00 M 5535 498150.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1807 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work,

including cutting, hoisting, fixing in position and applying a priming coat of approved steel

primer all complete.

15000.00 kg 334 5010000.00

1808 HSD STORAGE AND SUPPLY SYSTEM

Supply, installation, testing & commissioning of HSD storage tank 30 KL capacity (6 mm thick

shell & 8 mm thick dished shell) as per IS-10987 and approved for construction, shop drawings

duly approved by “CCOE” suitable for under ground installation including the following: (Civil

work and sand filling by other agency)

Inlet and outlet connections

Vent pipe.

0 0.00

1809 HSD storage tank as described above. 1.00 Set 46941 46941.00

1810 Supply, installation, testing & commissioning of electrical driven rotary gear pumps suitable for

pumping of HSD consisting of following :

Horizontally mounted single stage capable of delivering 110 LPM at 30 Mtr. Head while running

at required 1440 RPM, complete with proper connection to suction and delivery line, bypass

arrangement against over pressure.

Flame proof motor for fire protection pumping unit suitable for 400 + 10% V, 3 phase, 50 Hz AC

supply and of suitable HP for the above pumps.

Flame proof ON/ OFF push button station suitable for above motor including connection and

inter connection with starters’s installed in MCC.

Common base plate of required strength manufactured out of MS channels.

Suitable anti vibration damping arrangement with cushy foot or similar mounting arrangement.

Coupling and coupling guard for direct coupling of pump and motor.

Pressure gauge with valve on the delivery side.

Strainer at inlet.

0 0.00

1811 The pump set as described above with outdoor protection duty 2.00 Set 26078 52156.00

1812 Providing & fixing M.S. class ‘C’ (heavy duty) pipe & fittings like tees, elbows, junctions, unions,

bends, plugs etc. RCC pipe sleeves of larger diameter to the provided wherever the pipes are

0 0.00

1813 25 mm dia 100.00 RM 158 15800.00

1814 50 mm dia 40.00 RM 306 12240.00

1815 Excavation of required depth and back filling with compaction in soil for HSD fuel oil piping

including ramming the earth and making good.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1816 Pipe up to 50 mm dia 20.00 RM 532 10640.00

1817 Providing & fixing Cast steel ball valves of the following sizes suitable for pressure of 10

kg/sqcm complete with all necessary fittings

0 0.00

1818 25 mm dia 30.00 No. 1363 40890.00

1819 50 mm dia 1.00 No. 3633 3633.00

1820 Providing & fixing cast steel non return valves of the following sizes G.M. suitable for pressure

of 10 kg/sqcm complete with all necessary fittings

0 0.00

1821 50 mm dia 1.00 No. 2893 2893.00

1822 Providing & fixing level controller for day oil storage tanks including wiring, cabling, probes with

all other accessories for automatic operation of fuel pumps complete as required.

3.00 Set 8175 24525.00

1823 Providing & fixing ultrasonic level transmitter with local display unit in plant room for

underground oil storage tanks including wiring, cabling, probes with all other accessories for

automatic operation complete as required. Level indications shall be compatible with BAS.

1.00 Set 67803 67803.00

1824 Providing & fixing oil flow meter with 50 mm dia flanged end for HSD service 1.00 Set 59042 59042.00

1825 Providing and fixing Y/bucket strainer for oil supply line 0 0.00

1826 50 mm dia 2.00 No. 3635 7270.00

1827 Providing & fixing unloading point consisting of 1 No. ‘Y’ strainer, with 1 No. Ball valves on inlet,

outlet & by pass 1 No. drain valve, 1 No. 3 meter long flexible hose with necessary suitable

connection for all oil tanker outlet complete as required.

0 0.00

1828 80 mm dia 1.00 No. 5652 5652.00

1829 Providing & fixing GM collection assembly fitted with lockable brass cap suitable for local oil

tanker

1.00 No. 4718 4718.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1830 Supply, installation, testing and commissioning of 900 litres capacity day oil storage tank

fabricated from 4 mm thick MS plates. Tank shall include 450 mm ID manhole cover, level

indicator and flanged connection for inlet, outlet, overflow drain and probe provision for level

controller. Tank shall be mounted on 2 m high structure support with access ladder (painted

with 2 coats of red oxide primer).

1.00 Set 22427 22427.00

1831 Supply, installation, testing and commissioning of 900 litres capacity Buffer/ Over flow oil

storage tank fabricated from 4 mm thick MS plates. Buffer/ Over flowTank shall include 450

mm ID manhole cover, level indicator and flanged connection for inlet, outlet, overflow drain

and probe provision for level controller. Tank shall be mounted on 2 m high structure support

with access ladder (painted with 2 coats of red oxide primer) and sump tank shall be provided

blow the ground level treated with anticorrosive treatment..

2.00 Set 16586 33172.00

1832 MDB -1&2






415 volts.

0 0.00

1833 Incoming

1 No.800 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based

release unit with overcurrent and short circuit with ROH having following protection;



0 0.00

1834 Outgoing

3 No.160 amps TP+N Moulded Case Circuit Breaker Ics= Icu 35 kA,with Thermal based

release unit with ROH having following protection;







0 0.00

1835 MDB -1described as above 2.00 Set 326147 652294.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1836 MDB - 3






415 volts.

0 0.00

1837 Incoming

1 No.800 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based

release unit with overcurrent and short circuit with ROH having following protection;



Metering & Indication


2 No. Digital Electronic Energy Meter with necessary protection and port for BMS

communication, 3 Nos. 800/5 amps 10VA

2 set of Phase indicating light shall be protected by 6A MCB.

Bus Bars


sleeve. - 1 Set

0 0.00

1838 Outgoing













0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1839 1 No.100 amps TP+N Moulded Case Circuit Breaker Ics= Icu 35 kA,with Thermal based




0 0.00

1840 MDB -3 described as above 1.00 Set 153628 153628.00

1841 EXTERNAL LIGHTING FEEDER PILLAR (IP 55)

Design, manufacture, supplying fixing in position of outdoor type feeder pillar, metal clade,

suitable for 415 volt, 3-phase, 50 Hz with suitable foundation and arrangement for incoming/

outgoing cable termination, earthing, locking arrangement, insulated aluminium bus bars

system, interconnection etc.

0 0.00

1842 INCOMER

1 No. 100 amps 4P Ics= Icu 25 kA, Moulded Case Circuit Breaker with Thermal release unit

with ROH having following protection;

• Overload (Fixed thermal)




Phase indicating light shall be protected by 6A MCB. - 1 Set

Bus Bars

1 Set of 150A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOING

1 No. 40 A, TPN MCB, 10 KA

1 No. 63 A, TPN MCB, 10 KA

18 No. 6-32A, SP MCB, 10 KA

3 Nos. 63 A, DP MCB, 10 KA , along with 3No. 40 A 4Pole contactor and 3No. timer switch

0 0.00

1843 EXTERNAL LIGHTING FEEDER PILLAR (IP 55)_ described as above 2.00 Set 71001 142002.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1844 MDB -4 (KITCHEN FOR HOSPITAL)






415 volts.

0 0.00

1845 Incoming










Bus Bars


sleeve. - 1 Set

Outgoing

63 A TP+N MCCB -3 No.

63 A 4 Pole MCB -3 No.

63A 4 Pole MCB with 63 A 4 Pole RCCB of 30mA - 4 No.


63A DP MCB with 63 A DP RCCB of 30mA - 4 No.

40A DP MCB with 40 A DP RCCB of 30mA - 4 No.

0 0.00



Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1847 MDB -5 (LAUNDRY FOR HOSPITAL)






415 volts.

Incoming





0 0.00

1848 1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.




Bus Bars


sleeve. - 1 Set

Outgoing

63 A TP+N MCCB -3 No.

63 A 4 Pole MCB - 3 No.



0 0.00


1850 MDB - 6 (LIFT for Hospital)






415 volts.

Incoming



protection;





0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1851 2 No. Digital Electronic Energy Meter with necessary protection and port for BMS



Bus Bars


sleeve. - 1 Set

BUS COUPLER

1 No. 800 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with out release unit with

ROH having following protection;



Outgoing


based release unit with ROH having following inbuilt protection;

• Overload (adjustable microprocessor based )

• Earth Fault (adjustable microprocessor based )







0 0.00


1853 MDB - U1 (UPS INPUT PANEL FOR HOSPITAL)






415 volts.

0 0.00

1854 Incoming



protection;




0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1855 2 set of Phase indicating light shall be protected by 6A MCB.

Bus Bars


sleeve. - 1 Set

BUS COUPLER

1 No. 800 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with out release unit with

ROH having following protection;



Outgoing











0 0.00

1856 MDB -U1 described as above 1.00 Set 445094 445094.00

1857 SDB - 1.1&2 (Ventilation for Hospital)






415 volts.

0 0.00

1858 Incoming

1 No. 160 amps 4P, Ics= Icu 35kA, Moulded Case Circuit Breaker with microprocessor based






0 0.00

1859 SDB - 1.1 to 1.2 (Ventilation)_ described as above 2.00 Set 226268 452536.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1860 MDB -T1 ,T3(LIFT M/C RM FOR HOSPITAL)






415 volts.

0 0.00

1861 Incoming

1 No. 200 amps 4 Pole , Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor

based release unit with ROH & 200A 4 Pole ATS having following protection;








Bus Bars


sleeve. - 1 Set

Outgoing



• Overload (fixed magnetic )


2 No.63 amps 4 Pole Miniature Circuit Breaker Ics= Icu 10 kA,with microprocessor based




0 0.00

1862 MDB -T1,T3 described as above 2.00 Set 278024 556048.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1863 MDB -T2 (LIFT M/C RM FOR HOSPITAL)






415 volts.

0 0.00

1864 Incoming


based release unit with ROH & 100A 4 pole ATS having following protection;








Bus Bars


sleeve. - 1 Set

Outgoing

6 No. 63 amps TP+N Moulded Case Circuit Breaker Ics= Icu 50 kA,with microprocessor




2 No.63 amps 4 Pole Miniature Circuit Breaker Ics= Icu 10 kA,with microprocessor based




0 0.00

1865 MDB -T2 described as above 1.00 Set 160892 160892.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1866 MDB -T4 (LIFT M/C RM FOR HOSPITAL)






415 volts.

0 0.00

1867 Incoming


based release unit with ROH & 125A 4 Pole ATS with having following protection;








Bus Bars


sleeve. - 1 Set

Outgoing

8 No. 63 amps TP+N Moulded Case Circuit Breaker Ics= Icu 25 kA,with microprocessor




2 No.63 amps 4 Pole Miniature Circuit Breaker Ics= Icu 10kA,with microprocessor based




0 0.00

1868 MDB -T4 described as above 1.00 Set 192672 192672.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1869 SDB-G1 (GROUND FLOORFOR HOSPITAL)






415 volts.

0 0.00

1870 Incoming

1 No. 125 amps TP+N , Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor









Bus Bars


0 0.00

1871 SDB-G1 described as above 1.00 Set 112769 112769.00

1872 SDB-G2 (GROUND FLOOR FOR HOSPITAL)






415 volts.

0 0.00

1873 Incoming

1 No. 160 amps TP+N , Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor






0 0.00

1874 SDB-G2 described as above 1.00 Set 149089 149089.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1875 SDB-G3 (GROUND FLOOR FOR HOSPITAL)






415 volts.

0 0.00

1876 Incoming

1 No. 160 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor

based release unit with ROH having with following protection;





0 0.00

1877 SDB-G3_ described as above 1.00 Set 139100 139100.00

1878 SDB-G4 (GROUND FLOOR FOR HOSPITAL) 0 0.00

1879 Design, manufacture, supplying fixing in position of the following front operated cubicle type,





415 volts.

0 0.00

1880 Incoming







0 0.00

1881 SDB-G4_ described as above 1.00 Set 139100 139100.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1882 SDB-1.1 (FIRST FLOOR FOR HOSPITAL)






415 volts.

0 0.00

1883 Incoming










Bus Bars

150 Amps TPN, 25 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation

sleeve. - 1 Set

Outgoing

4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set


2 No. 40A 4pole MCB & 2 No. 25A 4 Pole MCB with 1No.Kwh Meter -1 Set

0 0.00

1884 SDB-1.1_ described as above 1.00 Set 126389 126389.00

1885 SDB-1.2(FIRST FLOOR FOR HOSPITAL)






415 volts.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1886 Incoming










Bus Bars


sleeve. - 1 Set

Outgoing



1 No. 40A 4pole MCB & 4 No. 25A 4 pole with 1No.Kwh Meter -1 Set

0 0.00


1888 SDB-1.3,1.4(FIRST FLOOR FOR HOSPITAL)






415 volts.

0 0.00

1889 Incoming







0 0.00

1890 SDB-1.3,1.4_ described as above 2.00 Set 126389 252778.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1891 SDB-2.1(SECOND FLOOR FOR HOSPITAL)






415 volts.

0 0.00

1892 Incoming







0 0.00


1894 SDB-2.2,2.3,2.4(SECOND FLOOR FOR HOSPITAL) 0 0.00

1895 Design, manufacture, supplying fixing in position of the following front operated cubicle type,





415 volts.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1896 Incoming










Bus Bars


sleeve. - 1 Set

Outgoing


1N0.63A TP+N MCCB & 4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set

2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set

0 0.00

1897 SDB-2.2,2.3,2.4_ described as above 3.00 Set 146364 439092.00

1898 SDB-3.1,3.3,3.4(THIRD FLOOR FOR HOSPITAL)






415 volts.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1899 Incoming










Bus Bars


sleeve. - 1 Set

Outgoing


1N0.63A TP+N MCCB & 1N0.63A TP+N MCCB & 4 No. 63A 4pole MCB with 1No.Kwh Meter

-1 Set


0 0.00

1900 SDB-3.1,3.3,3.4_ described as above 3.00 Set 158169 474507.00

1901 SDB-3.2(THIRD FLOOR FOR HOSPITAL)






415 volts.

0 0.00

1902 Incoming







0 0.00



Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1904 SDB-4.1(FOURTH FLOOR FOR HOSPITAL)






415 volts.

0 0.00

1905 Incoming










Bus Bars


sleeve. - 1 Set

Outgoing



0 0.00


1907 SDB-4.2 (FOURTH FLOOR FOR HOSPITAL)






415 volts.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1908 Incoming










Bus Bars


sleeve. - 1 Set

Outgoing




0 0.00








415 volts.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1911 Incoming










Bus Bars


sleeve. - 1 Set

Outgoing


1N0.63A TP+N MCCB & 4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set


0 0.00



Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)







415 volts.

Incoming










Bus Bars


sleeve. - 1 Set

Outgoing




0 0.00



Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1915 SDB-RM-UG1,U1,U2,U3&U4(GROUND FLOOR FOR HOSPITAL)






415 volts.

Incoming


release unit with ROH & 200A 4 Pole ATS having with following protection;








Bus Bars


sleeve. - 1 Set

Outgoing

6 No. 40A DP MCB with 1No.Kwh Meter -1 Set


0 0.00

1916 UG1,U1,U2,U3&U4_ described as above 5.00 Set 204476 1022380.00

1917 Rising Mains (Sandwitch insulated Construction)

Design, manufacture, supply, assembling, installation in correct assigned position, making

proper connections, testing and commissioning of following rating 4 pole sand witch type rising

mains of aluminium bus bar with tap-off connection points at every 1000 mm intervals,

expansion joints, fire barriers including necessary support and louvers for ventilation, fabricated

out of GI / Extrunded aluminium sheet including 2 Nos. of 50 x 6 mm GI/Aluminium earthing

conductor through out the length of the rising mains (Phase sequence should be matched with

the incoming breaker provided at LT Panel). Thrust pad shall be provided for each rising main

for necessary support to rising main and to prevent the bus bar expansion in downward

direction. Also end cover to close the end of rising main and to provide extra supports to bus

bars at end shall be provided. Dimension to be furnished with the offer.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1918 630 A, Isc = 50 kA for 1 second 12.00 RM 13854 166248.00

1919 400 A, Isc = 25 kA for 1 second 12.00 RM 10717 128604.00

1920 Supply, installation, testing and commissioning of following rating Reducer for rising mains of

sandwitch construction of Aluminium bus bars with expansion joints, fire barriers including

fabricated out of GI / Extrunded aluminium sheet including 2 Nos. of 50 x 6 mm GI/Aluminium

earthing conductor through out the length of the rising mains

0 0.00

1921 630 to 400 amps 4 Pole Rising Mains 2.00 No. 36076 72152.00

1922 Supply, installation, testing and commissioning of following rating end flange with enclosure for

sand witch rising mains of sandwitch construction of Aluminium bus bars for end termination

with expansion joints, fire barriers including fabricated out of GI / Extrunded aluminium sheet

including 2 Nos. of 50 x 6 mm GI/Aluminium earthing conductor through out the length of the

rising mains (Phase sequence should be matched with the incoming breaker provided at LT

Panel).

0 0.00

1923 630 Amps Rising Mains 2.00 No. 17189 34378.00

1924 Design, manufacture, supply, assembling, installation in correct assigned position, making

proper connections, testing and commissioning of following rating Adopter Boxes fabricated out

of 16 gauge CRCA sheet steel in cubical formation, dust and vermin proof, coupled with rising

mains. Boxes shall be treated with all anticorrosive process before powder coating as per

specifications. 2 No. earthing terminals shall be provided. Boxes shall be suitable for

connecting of rising mains at top and aluminium cables at bottom.The cost shall be included of

MCCB/ACB.

0 0.00

1925 630 Amps Amps MCCB for Rising Mains Adopter 2.00 No. 59597 119194.00

1926 Supply, installation, testing and commissioning of tap off boxes made up of 14 / 16 gauge

CRCA sheet steel mounted on the rising mains including providing of following MCCB’s with

operating handle as required with all accessories and adequate space shall be provided for

cable terminations.

0 0.00

1927 200 Amps 4 Pole MCCB of 25 KA. 4.00 No. 28264 113056.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1928 100 Amps 4 Pole MCCB of 25 KA. 4.00 No. 10715 42860.00

1929 Supply, installation, testing and commissioning of following rating of rising man end cap. 0 0.00

1930 400 Amps Rising Mains 2.00 No. 6637 13274.00

1931 LT CABLES

CONTROL CABLE END TERMINATION(SUBSTATION)

Supply of following sizes of XLPE insulated PVC sheathed aluminium conductor armoured

power cable of 33 kV grade (33kV earthed system) conforming to IS 7098 (Part-II) amended

upto date.

0 0.00

1932 3 Core, 300 Sq.mm. 230.00 Mtr 1630 374900.00

1933 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN

MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A,

tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without

MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3

phase outlets are required.)

0 0.00

1934 12 way (4 + 36), Double door 9.00 No. 17321 155889.00

1935 33 kV CABLE END TERMINATION

Supplying and making cable end jointing with heat shink push on type , including lugs and

other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 33 KV

grade as required :

0 0.00

1936 3 Core 300 Sq.mm (indoor) 8.00 Set 16889 135112.00

1937 3 Core 300 Sq.mm (Outdoor) 4.00 Set 17776 71104.00

1938 SUPPLY OF L T 1.1 kV CONTROL CABLES

Supplying of following sizes of 1.1 kV grade PVC insulated copper conductor armoured

stranded Control Cable conforming to IS :1554 complete as required and as per specifications.

0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1939 4 core, 2.5 Sq.mm. Cu. Conductor cable 400.00 M 89 35600.00



1942 19core, 2.5 Sq.mm. Cu. Conductor cable 200.00 M 329 65800.00

1943 Supplying and making end termination with double brass compression gland and Copper lugs

for following size of PVC sheathed copper conducter armoured control cable of 1.1 kV grand as

required.

0 0.00

1944 4 C x 2.5 Sq.mm. 16.00 Set 250 4000.00

1945 7 C x 2.5 Sq.mm. 40.00 Set 250 10000.00

1946 12 C x 2.5 Sq.mm. 26.00 Set 358 9308.00

1947 19 C x 2.5 Sq.mm. 12.00 Set 358 4296.00

1948 Supply of XLPE insulated and PVC sheathed Aluminium conductor armoured cable of 1.1 KV


0 0.00

1949 3.5core, 400 Sq.mm. 0 0.00

1950 3.5core, 300 Sq.mm. 4800.00 Mtr 696 3340800.00

1951 3.5core, 240 Sq.mm. 3500.00 Mtr 567 1984500.00

1952 3.5 core, 185 Sq.mm. 1170.00 Mtr 451 527670.00

1953 3.5 core, 150 Sq.mm. 850.00 Mtr 362 307700.00

1954 3.5 core, 120 Sq.mm. 1804.00 Mtr 305 550220.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1955 3.5 core, 95 Sq.mm. 1735.00 Mtr 245 425075.00

1956 3.5 core, 70 Sq.mm. 1245.00 Mtr 202 251490.00

1957 3.5 core, 50 Sq.mm. 568.00 Mtr 149 84632.00

1958 3.5 core, 35 Sq.mm. 655.00 Mtr 114 74670.00

1959 4 core, 25 Sq.mm. 827.00 Mtr 98 81046.00

1960 3 core, 25 Sq.mm. 260.00 Mtr 81 21060.00

1961 4 core, 16 Sq.mm. 4750.00 Mtr 77 365750.00

1962 3 core, 16 Sq.mm. 100.00 Mtr 64 6400.00

1963 4 core, 10 Sq.mm. 6600.00 Mtr 68 448800.00

1964 3 core, 10 Sq.mm. 3440.00 Mtr 60 206400.00

1965 Supply of XLPE insulated and PVC sheathed copper conductor armoured cable of 1.1 KV


0 0.00

1966 4 core, 6 Sq.mm. 700.00 Mtr 158 110600.00

1967 3 core, 6 Sq.mm. 800.00 Mtr 122 97600.00

1968 Supply of XLPE insulated and PVC sheathed copper conductor unarmoured cable of 1.1 KV


0 0.00

1969 1 core,120 Sq.mm 420.00 Mtr 712 299040.00

1970 1 core, 50 Sq.mm 640.00 Mtr 295 188800.00

1971 1 core, 10 Sq.mm.(LV System earthing) 600.00 Mtr 92 55200.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1972 1 core, 6 Sq.mm.(LV System earthing) 800.00 Mtr 53 42400.00

1973 Supplying and making end termination with brass double compression gland and copper lugs

for following size of PVC insulated and PVC sheathed / XLPE copper conductor Unarmoured

cable of 1.1 KV grade as required.

0 0.00

1974 1 core, 120 Sq.mm. 48.00 Sets 533 25584.00

1975 1 core, 50 Sq.mm. 16.00 Sets 355 5680.00

1976 1 core, 10 Sq.mm. 16.00 Sets 124 1984.00

1977 1 core, 6 Sq.mm. 16.00 Sets 123 1968.00

1978 Providing,fixing and laying of following dia hume Pipe NP2 class(light duty) in ground with RCC

collars,jointing with cement mortor 1:2 (1cement+2fine sand) including trenching 75cm deep

and re-filling as required.

0 0.00

1979 150 mm dia 10.00 RM 722 7220.00

1980 300 mm dia 30.00 RM 875 26250.00

1981 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories

like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting,

jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the

trench but excluding sand cushioning and protective covering etc., complete as required.

0 0.00

1982 90 mm dia (OD-90 mm & ID-76 mm nominal) 200.00 RM 256 51200.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

1983 HOT DEEP GI CABLE TRAYS, RACEWAY & JUNCTION BOXES:

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray




0 0.00

1984 100 mm width X 50 mm depth X 1.6 mm thickness 1178.00 Mtr 559 658502.00




1988 600 mm width X 62.5 mm depth X 2.0 mm thickness 900.00 Mtr 885 796500.00




“bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in



0 0.00

1992 100 mm width x 50mm depth x 1.6 mm thickness. 20.00 each 778 15560.00



1995 450 mm width x 50mm depth x 2 mm thickness. 10.00 each 942 9420.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)





“Tee” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in



0 0.00








2007 Supplying and installing following size of Hot Dipped Galvanised Iron Raceways with cover




0 0.00

2008 100 mm width X 40 mm depth X 1.6 mm thickness GI Raceways 800.00 Mtr 560 448000.00

2009 150 mm width X 40 mm depth X 1.6 mm thickness Raceways 300.00 Mtr 693 207900.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

2010 300 mm width X 40 mm depth X 1.6 mm thickness Raceways 200.00 Mtr 1094 218800.00

2011 Providing and fixing of 150 x 150 x 50 mm deep (Nominal size) wall junction box including

providing 2 mm thick Hot deep - galvanized GI steel cover required as per specification.

50.00 No. 599 29950.00



40.00 No. 880 35200.00



80.00 No 1004 80320.00

2014 Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as

required.

600.00 RM 1681 1008600.00

2015 LIGHTING FIXTURES 0 0.00

2016 Supply of Recessed Mounted 2'X2' Panel LED comprising of 40W LED with non integral /

integral driver, 6500K color temp having 40000 burning hrs life with minimum @ L 70, system

lumen output should be minimum with efficacy > 100 lm/W. LED driver PF 0.95 & THD < 20%.

The colour rendering index of LED light should be more than 70. Submission LM 80-08 Form

LED Source Manufacturer & LM79-08 / IS16106 from NABL approved lab. Manufacturer

mandatory i/c connection wire, testing etc. to complete the job.

492.00 Each 2577 1267884.00

2017 Supply of Surface Mounted 2'X2' Panel LED comprising of 40W LED with non integral /






1833.00 Each 2020 3702660.00

2018 Supply of Surface Mounted Led tube light fixture with inbuilt rod comprising of 20W LED tube

with non integral / integral driver, 6500K color temp having 40000 burning hrs life with minimum

@ L 70, system lumen output should be minimum with efficacy > 100 lm/W. LED driver PF

0.95 & THD < 20%. The colour rendering index of LED light should be more than 70.

Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL

approved lab. Manufacturer mandatory i/c connection wire, testing etc. to complete the job.

319.00 Each 905 288695.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

2019 Supply of Recessed Mounted Led Down Lighter comprising of 15W LED with non integral /






1490.00 Each 592 882080.00

2020 Supply of Surface Mounted Led Down Lighter comprising of 18W LED with non integral /






558.00 Each 1045 583110.00

2021 Supply of Recessed Mounted Led Down Lighter comprising of 18W LED with non integral /






385.00 Each 732 281820.00

2022 Supply of Surface Mounted Led Down Lighter comprising of 12W LED with non integral /






679.00 Each 697 473263.00

2023 Supply of Surface Mounted LED Down Lighter comprising of 10W LED with non integral /






227.00 Each 697 158219.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

2024 Supply of Wall mounted 9W LED Bulk head light fixture, LED of 1 to 3 W each assembled on

single MCPCB, having color temp 6500K & having 40000 burning hrs life with minimum @ L

70, system lumen output should be minimum with efficacy>80lm/W. LED driver PF 0.95 & THD

< 20%. The colour rendering index of LED light should be more than 70. Housing made of

CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 80-

08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL approved lab.

Manufacturer mandatory. i/c connection wire, testing etc. to complete the job.

98.00 Each 732 71736.00

2025 supply testing and commissioning of ceiling fan 5 star rating enery efficient , including wiring the

down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper

conductor, single core cable, including earthing and providing and fixing phenolic laminated

sheet cover on the fan box etc. as required.

984.00 No 1742 1714128.00

2026 supply testing and commissioning of exhaust fan upto 450 mm sweep in the existing opening,

including making the hole to suit the size of the above fan, making good the damage,

connection, testing, commissioning etc. as required.

79.00 No 1010 79790.00

2027 AREA LIGHTS 0 0.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

2028 Supply, Installation, Testing and Commissioning of 70W LED based Street light, housing made

up of Pressure Die Cast Housing LM 6 Alloy/ Anti Dust Exposed Lens,sturdiness and

embossed brand name/logo name of manufacturer. The fixture should have a minimum system

efficacy of 110 lumen/Watt and a minimum system lumen output of 18000 lumens. The fixture

shall have a CRI of minimum 70. The fixture shall be designed for a system life of 50,000 hours

@70% lumen maintenance. Ingress Protection of IP66 (lamp and gear Compartment) and

Mechanical Impact Resistance Rating of IK >=08.The fixture driver should have an operating

voltage range of 140-270 V, surge protection of >=3KV, PF >0.9 , THD<10% and SDCM<5.

The fixture should be top openable & easy access to the Gear Compartment. The driver should

be BIS approved, fully potted and encapsulated with 440V Stress Voltage protection for 8 Hrs.

High Cut off : 325V(+/- 15V) and Auto Restart function should also be available within the

fixture.The fixture should comply with the parameters as per IS10322. The LED driver should

comply to IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction

with IEC61347-1 ed.2.0, 2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for performance and

IEC61547 ed.2.0, 2009, CISPR-15 for EMI. Manufacturer shall have inhouse lab approved by

NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted

from a NABL/UL accredited lab to verify above parameters. Similar to Philips BRP340 LED 184

CW HO SLC S1 PS 1xLED/Cromption-LSTN-170-CDL-A/ENDO

84.00 Nos 5929 498036.00

2029 Supply, Installation, Testing and Commissioning of LED Post Top as Gate Light with a system

lumen output of 2300 lumens and a minimum system efficacy of >85 lm/W. The luminaire shall

have a rated system lifetime of 25,000 burning hours at L70. The luminaire should have a color

temperature of 3000K and CRI > 70. The luminaire shall meet IP65 with THD < 20% and PF >

0.9. The luminaire shall have closed diffused optics with polycarbonate diffuser board. The total

power consumption should not exceed 27W (including driver). Similar to BGP161

LED2300/WW PSU 220-240V 7043 IN/Cromption-LPTH20-CDL/ENDO

4.00 Nos 4069 16276.00

2030 Supply Installation Testing Commissioning of GI 7.0 mtr octagonal Pole with 1200mm single

arm Arm with inbuilt weather proof box including CC foundation (1:2:4 cement concrete (1

cement : 2 coarse sand : 4 graded stone aggregate 40mm nominal size) including excavation &

refilling etc minimum size 350mm x350mmx500mm with 300mm x 300mm x10 mm Base plate

including 4 Nos. heavy duty foundation nut bolts with suitable length as required and complete

in all respect as per direction of Engineer in Charge

84.00 Nos 9716 816144.00

2031 Supply and Installation of 4.5 meter high Decorative MS pole (3.6 meter above and 0.9 meter

below ground with ladder bars including chatsworth kit, junction box complete as per

requirement with all accessories.

6.00 Nos 7368 44208.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

2032 UPS SYSTEM

Supply, installation, Testing and commissioning of the following rating UPS as per Technical

Specifications and complete in all respects.

160 KVA UPS 3 phase (415 V + 15%) Volts input & 3 phase output (415 V + 1%), 50 Hz,

Input harmonic Current THD <=3% typical at 100% load, ,<=6% maximum at 50% load with

Isolation Transformer and 30 min Battery backup for each UPS along with battery cabinet

complete in all respect including supporting steel structure for UPS and Battery as

required.UPS shall have facility for parallel operation.

Quoted price shall be inclusive of required rating single core copper conductor cable

including terminations,connections of UPS to panels, batteries etc complete in all respect and

as per direction of Engineer in Charge.

3.00 Set 219058 657174.00

2033 40 KVA UPS 3 phase (415 V + 15%) Volts input & 3 phase output (415 V + 1%), 50 Hz, Input

harmonic Current THD <=3% typical at 100% load, ,<=6% maximum at 50% load with Isolation

Transformer and 30 min Battery backup for each UPS along with battery cabinet complete in

all respect including supporting steel structure for UPS and Battery as required.UPS shall have

facility for parallel operation.




2.00 Set 678037 1356074.00

2034 40 KVA UPS 3 phase (415 V + 15%) Volts input & 3 phase output (415 V + 1%), 50 Hz, Input

harmonic Current THD <=3% typical at 100% load, ,<=6% maximum at 50% load with Isolation

Transformer and 30 min Battery backup for each UPS along with battery cabinet complete in

all respect including supporting steel structure for UPS and Battery as required.UPS shall have

facility for Stand alone operation.




1.00 Set 678037 678037.00

Data & Voice system 0

2066 MATV,DATA & VOICE SYSTEM SYSTEM

Supplying and drawing co-axial TV cable RG-11 grade, solid copper conductor PE insulated,

shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/

recessed steel/ PVC conduit as required.

385.00 meter 118 45430.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

2067 Supply, erection, testing and commissioning of splitter / tap off mounted in suitable sizes MS

boxes for MATV system and shall be suitable for interactive system.

0 0.00

2068 Four way (S-4) 10.00 Each 3007 30070.00

2069 Four way Tap Off (T4) 29.00 Each 2506 72674.00

2070 Supply, installation, testing and commissioning of Bi-directional line extender amplifier housed

in suitable size of MS box of CRCA sheet.

6.00 Each 7922 47532.00

2071 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper

conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as

required.

0 0.00

2072 20 Pair 50.00 meter 116 5800.00

2073 50 Pair 100.00 meter 329 32900.00

2074 100 Pair 50.00 meter 509 25450.00

2075 Supply,Installation,testing and Commissioningof following telephone teg block 0 0.00

2076 10-30 Pair 20.00 No. 2979 59580.00

2077 50 Pair 1.00 No. 3882 3882.00

2078 100 Pair 1.00 No. 5787 5787.00

2079 800 Pair 2.00 No. 8897 17794.00

2080 Supply & instalation of 6 core Indoor/outdoor OM3 Unarmoured Multimode Optical Fiber 200.00 Mtr 826 165200.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

2081 Supply, installation, testing and commissioning of 24 port L2 Managed switch having port

density 24 Nos of 10M/100M/1G RJ45 Port POE ports , 2 Nos of GbE RJ45/SFP Combo Port ,

1X console port , Available POE power 370 W , 52 Gbps switching bandwidth , 8K MAC

address support , Support L2 feature STP, RSTP ,MSTP . Support 802.1Q VLAN , port based

VLAN , 4K VLAN entries , MAC based VLAN , IP subnet based VLAN . Support IEEE 802.3ad

LACP . L3 features - static routing , DHCP feature , Device Management system - topology

view , floor view , map view , dashboard , traffic monitoring , cable diagnostics.CE,FCC

certified. (Approved make - Cisco / Impulse / Juniper)

50.00 Set 69357 3467850.00

2082 Supply, Installation, Testing & Commissioning of 24 port L2 Managed switch having port

density 24 Nos of 10M/100M/1G RJ45 Port POE ports , 4 Nos of 1G/10G SFP+ Port , 1X

console port , Available POE power 370 W , 128 Gbps switching bandwidth , 32K MAC

address support , Support L2 feature STP, RSTP ,MSTP . Support 802.1Q VLAN , port based

VLAN , 4K VLAN entries , MAC based VLAN , IP subnet based VLAN . Support IEEE 802.3ad

LACP . L3 features - static routing , DHCP server , Device Management system - topology view

, floor view , map view , dashboard , traffic monitoring , cable diagnostics.CE,FCC certified

(Approved make - Cisco / Impulse / Juniper)

4.00 Set 103008 412032.00

2083 Supply, installation, testing and commissioning of CISCO/aruba /ruesh Make router (ABGN)

with , CAT-6E Port for indoor solution, suitable to creat Wi-Fi on entire floor as required.

20.00 Set 12435 248700.00

2084 Supply, installation, testing and commissioning of CAT-6 Patch cabel as per EIA upto 1.2mtr

length as required.

1200.00 Set 667 800400.00

2085 Wall /Floor Mount Rack Enclosure Cabinet suitable for Data Patch Panel /Data switch ,

Constructed with a hinged wall mounting bracket and a sturdy steel frame, suitable to

accommodate up to 200 lbs. of equipment in 15U of rack space. Four adjustable vertical

mounting rails with square holes accommodate all standard 19-inch rack equipment. easy

access to rackmounted equipment, the enclosure cabinet is hinged to swing away from the wall

mounting bracket, perforated lockable side panels and front door, assuring generous airflow to

keep equipment operating safely. The front door shall be reversible and the side panels are

removable for easy access to equipment. The top and bottom panels of the enclosure include

convenient cable routing ports.

0 0.00

2086 42U as per EAI. 2.00 Set 92865 185730.00

2087 19U as per EAI. 1.00 Set 30678 30678.00

2088 9U as per EAI. 18.00 Set 15132 272376.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

2089 Supply, installation, testing and commissioning of following Port ,CAT-6 Loaded Patch Panel

as per EAI.

0 0.00

2090 24 Port ,CAT-6 Loaded Patch Panel 75.00 Set 8485 636375.00

0

2116 SOLAR-GRID CONNECTED SYSTEM

Supplying installation,testing and commissioning of each kW power with Solar Photovoltaic

system including PV Modules aluminium super structure supported on GI support, string

PCUs, Copper maintainace free copper earthing, connection of earthing pit to SPV system

including insulated copper strip / cables , associated power and control cabling from SPV panel

to power panel and Main distribution panel in each cluster as per specification complete in all

respect as per site requirement including cabling upto solar panel . (Inclusive of earthing for

DC as well as AC equipment or system)

20.00 kwp 53529 1070580.00

Nurse call System 0

2117 CONDUITING WIRING AND CABLING FOR NURSE CALL SYSTEM

Supply ,installation, testing and commissioning of the following .

Supply, Installation, Testing & Commissioning of the system IP based controller for a

decentralised communications node for exchanging data between the connected system

devices and the rest of the communications system, consisting of :

- Metal case,

- 1 x RJ45 socket, 100Mb IP Port (IEEE802.3 100BaseTX), galvanically isolated for connection

1.00 Nos. 124078 124078.00

2118 Nurse Station Terminal with antimicrobial coating having following features :

- Nurse Terminal shall comprises of required size TFT, Touch screen colour graphic display for

displaying all details

- Handset with speaker and mic.

- Speech communication facility with other nurses in network at any time.

-changeover between hands-free and discrete speaking , required size connection cable with

an RJ45 connection

0 0.00

2119 For 6 Patient Bed Rooms with 2 Washrooms and 1 corridoor 8.00 No. 119439 955512.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)



2122 Nurse Call Module

Nurse Call Module -Bed Side Unit with Handset module (with VOIP & SIP Functionality)

It shall have following features:-

- Nurse call with possibility for communications,

- Additional calls via service call key (optional) with possibility for communications,

- Integrated IP telephone end device (H.323 or SIP protocol stack)

- Controlling electronically driven shutters or other environmental applications,

88.00 Nos. 8815 775720.00

2123 Bath/Toilet Pull cord

Supply ,Installation ,Testing and commissioning of Pull cord type call button consisting of:

- Required length pull cord with ON & OFF facility and a luminous grip

- Moisture Protection

- Aniomicrobial coating

- VDE 0834/ UL 1069 certification

56.00 Nos. 9649 540344.00

2124 Supply ,Installation ,Testing and commissioning of corridoor indication consisting of:

DUAL direction LED indicator

0 0.00

2125 Cooridoor Indicator 16.00 Nos. 8997 143952.00

2126 Event Management Software

Providing, Installation, Testing and Commissioning of Software pack on the Management

Center for automati-cally handling of all events in the entire communications system, e.g. calls,

presences, call acknowledgements, presences etc.

This indication and analysis of the data is through a browser which has password-protected

access to the XML data on the server. Various filters make it easily to find and display the

required information.

1.00 No. 363533 363533.00


Sl.


Estimated Rate

(excluding GST)

TOTAL AMOUNT

(excluding GST)

2127 IPBX

Supply, Installation, Testing and Commissioning of IP PBX (Analog + IP) hyberid as per tender

specification -24 Analog Trunk Line, 02 Port PRI Line with 60 Channel Licenses 4000 Analog

Extensions , 50 IP Users , Integrated IP Gateway for IP Extension and ITSP's,Integrated UC on

Motherboard, 120 Channel DSP Resource built in (TDM to IP and Vise versa 5 Party Adhoc

Conference, DECT Compatible , Q-Sig Compatible , SIP Compatible, Remote Maintenance ,

Provisioned With 6 Port 300 Mailboxes,100 Auto Attendant 25 UC Smart Client etc. It should

be complete as per technical specifications & as per direction of Engineer-in-charge.

1.00 Nos. 210714 210714.00

2128 Providing On Board UC Smart Client for up to 350 Users with license Sipported with following

features Presense including status based announcements Favourites including Call status,

Visual Voice Mail, control Voicemail to e mail service, Ad hoc conferencing (up to 5 party),

Call Journal, Directory Access,Instant Messaging , Reminder etc. It should be complete as per

technical specifications & as per direction of Engineer-in-charge.

3.00 Nos. 58415 175245.00

2129 Providing and Installation of PC based Operator Console Supported with following features

Display of Waiting Calls with type, name and telephone number, Call Status display Speedy

Switching of calls, Individual Configuration of the busy fields with directory number or name

Color display of the busy status: Call, toggle, hold , park Number Redial (last 10 destinations)

Conference with up to 5 call participants Choice of electronic telephone books: System,

telephone book, outlook contacts, internal telephone bool, ldap access etc. It should be

complete as per technical specifications & as per direction of Engineer-in-charge.

1.00 Nos. 260783 260783.00

2130 Providing IP User license for SIP Phone. 20.00 Nos. 29938 598760.00

2131 Supply, Installation , Testing and Commissioning of Analog Caller ID Speaker Phone. 50.00 Nos. 1336 66800.00

2132 Supply, Installation , Testing and Commissioning of IP Phones. 350.00 Nos. 991 346850.00

144015315.00GRAND Total in Figures


Date post:	16-May-2020
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

the new Govt. Medical College at Balasore, Odisha VOLUME...

Documents