CEMINTEL DESIGNER SERIES™ CLADDING
OVERVIEW
The CSR Gyprock Red Book™ contains a wide range of fire and/or acoustic rated wall systems. This addendum provides information on a new series of external wall systems incorporating Cemintel Designer Series™ external cladding.
The Cemintel Designer Series™ walling system combines a modern contemporary appearance with the time and effort saving of a pre-finished panel, and a fast, easy to use installation system to deliver outstanding exterior cladding solutions for lightweight timber and steel stud framed applications.
APPLICATIONS
The Cemintel Designer Series™ system may be used on timber and steel framed buildings of up to two storeys that meet the geometric limits of AS4055 : Wind loads for housing. The system is suitable as an external cladding on Class 1 and Class 10 buildings only.
Cemintel Designer Series™ is ideal for structures with either slab-on-ground or elevated framing/concrete floor construction, including duplex and townhouse construction, extensions, upper storey additions and other applications where residential construction techniques are appropriate.
ADVANTAGES
• Cemintel Designer Series™ cladding offers extensive texture/colour choices to enhance design concepts to deliver an attractive, contemporary and unique external appearance.
• A choice of Gyprock™ and Cemintel™ internal linings to suit fire, acoustic, impact and wet area applications.
• Internal linings installed, jointed and finished using industry standard methods.
• Designer Series™ pre-finished panels are cement bonded wood-particle products. They are protected with NichiGuard coating, which has an anti-staining, self-cleaning function for an extended low-maintenance life.
• Systems compatible with cost effective, industry standard lightweight timber and steel stud wall construction.
• The Designer Series™ cladding system uses simple components and construction techniques to ensure fast and easy installation on timber or steel stud framing.
ADDITIONAL INFORMATION
The des ign and ins ta l l a t ion gu ide fo r Ceminte l Designer Series™ cladding can be downloaded at www.cemintel.com.au or call 13 17 44.
For technical assistance please contact CSR DesignLINK™, at [email protected] or call 1800 621 117.
www.gyprock.com.au www.cemintel.com.au
FIRE & ACOUSTIC DESIGN GUIDEAddendum December 2014
THE RED BOOK™
SYSTEM SPECIFICATION TYPICAL LAYOUT (CSR 917a shown) ACOUSTIC OPINION
PKA-089• Cemintel Designer Series™ External Cladding System.
• Sarking.
• Lining material to external side of studs as per system table.
• Timber Studs as per system design table.
• Lining material to internal side of studs as per system table.
NOTES:
*ACR = Axial Capacity Reduction. (Refer to Table C3, GYP500 The Red Book)
FRLReport/Opinion
SYSTEM Nº
WALL LININGSSTUD DEPTH mm 70 90 THERMAL
CAVITY INFILL Rw / Rw+Ctr Rt(win) Rt(sum)
–/–/–
CSR 917ExtErnal SidE of Stud
• Nil
intErnal SidE
• 1 x 10mm GYPROCK Plasterboard CD.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
48/39
–
47/37
50/41
51/42
49/39
2.6
3.3
2.3
2.3
3.0
2.0
WALL THICKNESS mm 111 131
30/30/30(from outside only)
FAR2303
CSR 918ExtErnal SidE of Stud
• 1 x 16mm GYPROCK FYRCHEK MR plasterboard.
intErnal SidE
• 1 x 6mm CeminSeal™ Wallboard.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
53/44
–
52/42
55/46
56/47
54/44
2.6
3.4
2.3
2.4
3.1
2.1
WALL THICKNESS mm 123 143
60/60/60*(from outside only)
FAR2303*ACR Group 2
CSR 919ExtErnal SidE of Stud
• 1 x 16mm GYPROCK FYRCHEK MR plasterboard.
intErnal SidE
• 1 x 10mm GYPROCK Plasterboard CD.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
53/44
–
52/42
54/45
55/46
53/43
2.6
3.4
2.3
2.4
3.1
2.1
WALL THICKNESS mm 127 147
60/60/60FAR2303
CSR 922ExtErnal SidE of Stud
• 1 x 16mm GYPROCK FYRCHEK MR plasterboard.
intErnal SidE
• 1 x 16mm GYPROCK FYRCHEK plasterboard.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
54/45
–
53/43
55/46
56/47
54/44
2.7
3.4
2.3
2.4
3.1
2.1
WALL THICKNESS mm 133 153
90/90/90(from outside only)
FAR2303
CSR 926ExtErnal SidE of Stud
• 2 x 13mm GYPROCK FYRCHEK MR plasterboard.
intErnal SidE
• 1 x 10mm GYPROCK Plasterboard CD.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
55/46
–
54/45
56/47
57/48
55/45
2.7
3.4
2.4
2.5
3.1
2.2
WALL THICKNESS mm 137 157
90/90/90*FAR2303
*ACR Group 3
CSR 929 ExtErnal SidE of Stud
• 1 x 6mm CeminSeal™ Wallboard. (against stud)
• 1 x 16mm GYPROCK FYRCHEK MR plasterboard.
intErnal SidE
• 2 x 13mm GYPROCK FYRCHEK plasterboard.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
58/50
–
57/48
59/51
60/52
58/49
2.7
3.5
2.4
2.5
3.2
2.2
WALL THICKNESS mm 149 169
Timber Frame External Wall Systems – Cemintel Designer Series™
SYSTEM SPECIFICATION TYPICAL LAYOUT (CSR 146a shown) ACOUSTIC OPINION
PKA-089• Cemintel Designer Series™ External Cladding System.
• Sarking.
• Lining material to external side of studs as per system table.
• Steel Studs as per system design table.
• Lining material to internal side of studs as per system table.
NOTES:
*ACR = Axial Capacity Reduction. (Refer to Table C3, GYP500 The Red Book)
FRLReport/Opinion
SYSTEM Nº
WALL LININGSSTUD DEPTH mm 76 92 THERMAL
CAVITY INFILL Rw / Rw+Ctr Rt(win) Rt(sum)
–/–/–
CSR 144ExtErnal SidE of Stud
• Nil
intErnal SidE
• 1 x 10mm GYPROCK Plasterboard CD.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
48/39
–
47/37
49/40
50/41
48/38
2.6
3.3
2.3
2.3
3.0
2.0
WALL THICKNESS mm 117 133
30/30/30(from outside only)
FAR2357
CSR 145ExtErnal SidE of Stud
• 1 x 13mm GYPROCK FYRCHEK MR plasterboard.
intErnal SidE
• 1 x 10mm GYPROCK Plasterboard CD.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
52/43
–
51/41
52/43
53/44
51/41
2.6
3.4
2.3
2.4
3.1
2.1
WALL THICKNESS mm 130 146
30/30/3060/60/60*90/90/90
FAR2357*ACR 15%
CSR 146ExtErnal SidE of Stud
• 1 x 13mm GYPROCK FYRCHEK MR plasterboard.
intErnal SidE
1 x 13mm GYPROCK FYRCHEK plasterboard.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
53/44
–
52/42
54/45
55/46
53/43
2.6
3.4
2.3
2.4
3.1
2.1
WALL THICKNESS mm 133 149
60/60/60*(from outside only)
FAR2357*ACR 5%
CSR 147ExtErnal SidE of Stud
• 1 x 16mm GYPROCK FYRCHEK MR plasterboard.
intErnal SidE
• 1 x 10mm GYPROCK Plasterboard CD.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
52/43
–
51/41
53/44
54/45
52/42
2.6
3.4
2.3
2.4
3.1
2.1
WALL THICKNESS mm 133 149
60/60/6090/90/90*
FAR2357*ACR 15%
CSR 149ExtErnal SidE of Stud
• 1 x 16mm GYPROCK FYRCHEK MR plasterboard.
intErnal SidE
1 x 16mm GYPROCK FYRCHEK plasterboard.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
54/45
–
53/43
54/45
55/46
53/43
2.7
3.4
2.4
2.4
3.1
2.1
WALL THICKNESS mm 139 155
90/90/90(from outside only)
FAR2357
CSR 148ExtErnal SidE of Stud
• 2 x 13mm GYPROCK FYRCHEK MR plasterboard.
intErnal SidE
• 1 x 10mm GYPROCK Plasterboard CD.
(a) 75 Gold Batts™ 2.0
(b) 90 Gold Batts™ 2.7
(c) NG Soundscreen™ 60
54/45
–
53/43
55/46
56/47
54/44
2.7
3.4
2.4
2.5
3.1
2.2
WALL THICKNESS mm 143 159
Steel Frame External Wall Systems – Cemintel Designer Series™
EXTERNAL WALL SYSTEMS WITH CEMINTEL DESIGNER SERIES™ CLADDING
www.gyprock.com.auSales Support Tel: 13 17 44 Fax: 1800 646 364CSR DesignLINK™ Tel: 1800 621 117
Cemintel Designer Series™ Panel
Stud framing (double studs at all vertical sheet joints)Building
Wrap
Starter Strip
Mask, prime and fill all vertical panel joints with colour matched joint sealant
��
Base Flashing�
Joint Backing Strip at all vertical joints�
Pre-formed Corner�
�
�
Corner Clips�
Panel Clip at 600mm max. cts �
�
Cemintel Designer Series™ Overview & Features• Cemintel Designer Series™
p a n e l s a r e i n s t a l l e d horizontally or vertically, and have complementary tongue and groove profiles along the long edges with an in-built flexible sealing strip.
• Panel Clips fit over the panel tongue edge, and accept and retain the groove edge of the adjoining panel providing invisible fixing. The integrated compressible strip provides a weathertight sealed joint.
• The Pre-formed Ex terna l Corners are easy to install, and provide an attractive matching f inish and expressed joint appearance.
• Pre-f inished Panels mean virtually no finishing work is required. Simply fill expressed joints with colour matched sealant and finish off with the matching touch-up kits.
i-Cube – Onyx
i-Cube – Quartz Textured – Ebony
Textured – Alpine
Textured – SandstoneSlimline – Slate
Woodgrain – Teak
Woodgrain – Oak
Urban – Grey
Smooth – Cream
Smooth – Mocha
Smooth – Frappe
Smooth – Latte
Cemintel Designer Series™ panel are available in a range of colours and textures
GYP500CDS.BMS1077.1214