Date post: | 30-Dec-2015 |
Category: |
Documents |
Upload: | uriel-oneil |
View: | 13 times |
Download: | 0 times |
The training program will now resume
Advanced User TrainingAdvanced User Training
Now for the interesting part:
“Field Programming”
SC PI
Advanced User TrainingAdvanced User Training
OK, you asked for it• The truth is that once you practice this procedure on an empty channel, you’ll find it follows very predictable steps from operation to operation
[Page Up] [Page Up]
oror NEXTNEXT
You need to know these things to enter a channel:
Advanced User TrainingAdvanced User Training
• Whether this is to be included in the Scan List
SC PI
[Page Up] [Page Up]
oror NEXTNEXT
• Whether this is a Narrow or Wide Band FM channel
[Page Up] [Page Up]
oror NEXTNEXT
• A name for this channel up to 10 characters long
[Page Up] [Page Up]
oror NEXTNEXT
• The TX & RX frequencies and subaudable tone
[Page Up] [Page Up]
oror NEXTNEXT
• Is this channel already programmed in this radio? [Page Up] [Page Up]
oror NEXTNEXT
Advanced User TrainingAdvanced User Training
Let’s first dial up the radio frequency
• Move the EDIT switch to the LEFT this time
• We’ll call this the EDIT CHannel selection• We’ll call this the EDIT CHannel selection
[Page Up] [Page Up]
oror NEXTNEXT
[Page Up] [Page Up]
oror NEXTNEXT
• The DISPlay switch now shows what it is that you’re changing - The name display, transmit frequency, receive frequency, etc [Page Up] [Page Up]
oror NEXTNEXT
Advanced User TrainingAdvanced User Training
• We’ll start with the DISPlay switch in the <center>
r
[Page Up] [Page Up]
oror NEXTNEXT
• We learned that the DISPlay switch in the (RX) position shows the Receive frequency
[Page Up] [Page Up]
oror NEXTNEXT
• It’s the same with programming: You’re programming whatever the DISPlay is set to show at the time
[Page Up] [Page Up]
oror NEXTNEXT
RX
Advanced User TrainingAdvanced User Training
• Being as the DISPlay now shows the RX display, we’ll begin programming the Receive frequency
r
[Page Up] [Page Up]
oror NEXTNEXT
• The NEXT switch chooses the digit to be edited
[Page Up] [Page Up]
oror NEXTNEXT
• The SELECT switch makes the number change[Page Up] [Page Up]
oror NEXTNEXT
Advanced User TrainingAdvanced User Training
• After each digit is SELECTed, go to the NEXT one and keep going until the whole frequency is entered
r
[Page Up] [Page Up]
oror NEXTNEXT
• Then, go NEXT even further over to the right, and enter the CTCSS tone as needed.
[Page Up] [Page Up]
oror NEXTNEXT
• That’s it for the Receive frequency[Page Up] [Page Up]
oror NEXTNEXT
Advanced User TrainingAdvanced User Training
• Now that we have an RX frequency, we’ll do the exact same thing for the Transmit side of the formula
rt
[Page Up] [Page Up]
oror NEXTNEXT
[Page Up] [Page Up]
oror NEXTNEXT
• Change the DISPlay switch to the right, to the TX setting
[Page Up] [Page Up]
oror NEXTNEXT
• Duplicate the frequency and tone which was put into the RX side (unless the circumstance directs otherwise)
Advanced User TrainingAdvanced User Training
The next step is to assign the Identification, Channel Bandwidth and Scan List inclusion The next step is to assign the Identification, Channel Bandwidth and Scan List inclusion The next step is to assign the Identification, Channel Bandwidth and Scan List inclusion The next step is to assign the Identification, Channel Bandwidth and Scan List inclusion
SC
[Page Up] [Page Up]
oror NEXTNEXT
• This step changes items seen in the ID screen, so we need to switch the DISPlay to ID to make these changes
[Page Up] [Page Up]
oror NEXTNEXT
• Again, use the NEXT switch to choose which space to edit, and then SELECT the letter, numeral, symbol needed• Again, use the NEXT switch to choose which space to edit, and then SELECT the letter, numeral, symbol needed• Again, use the NEXT switch to choose which space to edit, and then SELECT the letter, numeral, symbol needed
[Page Up] [Page Up]
oror NEXTNEXT
Advanced User TrainingAdvanced User Training
• For the time being, we’ll assume all field entries will be in Wide Band format, as used by our other radios at present
• The next choice is for Wide or Narrow FM channel width
W SC
[Page Up] [Page Up]
oror NEXTNEXT
• Select whether this channel is to be put on the Scan List for later use in channel scanning
[Page Up] [Page Up]
oror NEXTNEXT
Advanced User TrainingAdvanced User Training
W SC
• Finally, return the EDIT switch to the center position
[Page Up] [Page Up]
oror NEXTNEXT
• Finally, return the EDIT switch to the center position
Take a moment to go through this informal check-list just once more, to ensure that the equipment is ready for action…..
Setting OptionsSetting Options
w SC
Mission-Ready Check ListMission-Ready Check List
[Page Up] [Page Up]
oror NEXTNEXT
DISPlay Switch = ID
[Page Up] [Page Up]
oror NEXTNEXT
Channel = Air to Ground
or as directed by your local command[Page Up] [Page Up]
oror NEXTNEXT
SCAN Switch = Normal
(Not Scanning At This Time)
[Page Up] [Page Up]
oror NEXTNEXT
Guard1/Guard2 Switch = G2
or as directed by local command[Page Up] [Page Up]
oror NEXTNEXT
Verify that you left :
POWER = HI
[Page Up] [Page Up]
oror NEXTrtNEXTrt
TONES = ON
[Page Up] [Page Up]
oror NEXTrtNEXTrt
EDIT Switch = <Centered>
[Page Up] [Page Up]
oror NEXTrtNEXTrt
Final Practical ReviewFinal Practical Review
…and now for some practical review of setings….
Page Up Page Up
oror NEXTNEXT
PressPress Here Here for Answerfor Answer
Final Practical ReviewFinal Practical Review
You’re not transmitting CTCSS tone on your radio; Check and correct this no-tone-xmit condition
• Your ground team calls and urgently tells you they can only hear you when they use their “Monitor” button
• Why?
Page Up Page Up
oror NEXTNEXT
PressPress Here Here for Answerfor Answer
Final Practical ReviewFinal Practical Review
Pull, then move to the right, the EDIT/STep switch
• “How do I do that?” you ask.
Page Up Page Up
or or NEXTNEXT
Final Practical ReviewFinal Practical Review
Pull, then move to the right, the EDIT/STep switch
Use the NEXT switch to toggle around until you find the selection for TONE control options
• “How do I do that?” you ask.
“ NEXT”“ NEXT”
Page Up Page Up
or or NEXTNEXT
Final Practical ReviewFinal Practical Review
Use the SELECT switch to turn the TONES ON
“ SELECT”“ SELECT”
Page Up Page Up
oror NEXTNEXT
Final Practical ReviewFinal Practical Review
Use the SELECT switch to turn the TONES ON
Return the EDIT/STep switch to the Center
Page Up Page Up
or or NEXTNEXT
Final Practical ReviewFinal Practical Review
Page Up Page Up
or or NEXTNEXT
Return the EDIT/STep switch to the Center
Use the SELECT switch to turn the TONES ON
PressPress Here Here for Answerfor Answer
w
SC
Advanced User TrainingAdvanced User Training
• Name the things you need to know before you program a radio channel into this unit
- The Transmit and Receive Frequency
[Page Up] [Page Up]
oror NEXTNEXT
- The Subaudiable tone (CTCSS) required
Page Up Page Up
or or NEXTNEXT
- Is this channel already programmed in this radio?Page Up Page Up
or or NEXTNEXT
PressPress Here Here for Answerfor Answer
Final Practical ReviewFinal Practical Review
• What else would it help to know about this channel?
- A name for this channel up to 10 characters long
Page Up Page Up
oror NEXTNEXT
SC
- Whether this is to be included in the Scan List
[[Page Up Page Up
or or NEXTNEXT
- Whether this is a Narrow or Wide Band FM channelPage Up Page Up
or or NEXTNEXT
w
ConclusionConclusion
It is hoped that this Advanced User Training will assist you in the safe and confident operation of airborne missions using this piece of equipment
SCw
This concludes Part II, Advanced User Training on the use of the NPX138N VHF-FM Radio
end