+ All Categories
Home > Documents > Thermostat Processing Unit (CLI-8000-00 / CLI-8000A-00...

Thermostat Processing Unit (CLI-8000-00 / CLI-8000A-00...

Date post: 09-Jun-2018
Category:
Upload: buidieu
View: 252 times
Download: 0 times
Share this document with a friend
2
The Savant ® CLI-8000 and CLI-8000A eight zone Thermostat Processing Units are at the heart of the Savant ® Centralized Climate Control system. Through communications with a number of remote sensors and optional user interfaces, the Thermostat Processing Unit can manage up to eight heating, ventilation, and air conditioning (HVAC) systems. The system is easily integrated with most leading HVAC systems and can be designed as one part of a complete Savant ® Control System solution. The CLI-8000 version is configured using the keypad and display located on the front panel. The CLI-8000A version is configured using a climate application loaded onto an Android™ based tablet (Android is a trademark of Google Inc). The tablet, which is installed into the front cover of the TPU, incorporates a touch screen interface with an elegant climate control application for setting up, viewing, and controlling each climate zone independently. Once installed and configured, either system the can be integrated to add monitoring and control through an iOS device such as iPad ® or iPod ® . This Quick Reference Guide provides the information necessary to install the CLI-8000/8000A as well as information on wiring to each of the optional and required components of the Savant HVAC solution. Box Contents (1) CLI-8000 or CLI-8000A (Includes all mating connectors from front panel) (1) Quick Reference Guide (this document) Related Components Savant ® Host Savant ® Controller SSC-0008-XX, SSC-0025-XX External 120V AC to 24V AC Transformer, PWR-2440-XX Optional Remote Sensors Savant ® SST-TEMP1 - Remote Indoor Sensor Savant ® SST-OTEMP1 - Remote Outdoor Sensor Savant ® CLI-THFM1 - Remote Humidity/Temperature Smart Sensor Savant ® CLI-PLEN1C - Commercial Plenum Sensor (Heat duct sensor) Savant ® CLI-PLEN1R - Residential Plenum Sensor (Heat duct sensor) Savant ® CLI-SLAB1 - SLAB Sensor (Floor Heating Sensor) Note: Each zone on the CLI-8000/8000A supports communications with up to four temperature sensors and two humidity sensors. Specifications Environmenta al Temperature 32° to 104° F (0° to 40° C) Humidity 10% to 90% Relative Humidity (non-condensing) Dimensions a and Weight Height 12.17ʺ (31 cm) with cover; 11.05ʺ (28 cm) without cover Width 15.48ʺ (39.3 cm) with cover; 14.23ʺ (36.1 cm) without cover Depth 2.81ʺ (7.1 cm) with cover; 2.71ʺ (6.9 cm) without cover Weight 8.75 lb. / 4.0 kg Power Power (Input) 24V AC (40VA) from external transformer Cable Require ements Relay Bank to HVAC system 18 American Wire Gauge (AWG) Standard HVAC wiring (RH, RC, W1, W, Y1, Y2, G, O, Aux) Note: If required, RH and RC can be jumped together. Cable Require ements (Sensors) Data Sensor Bus (1-Wire) 24 AWG (Cat 5) 600 feet (182 m) maximum (cumulative) Remote Sensor 24 AWG (Cat 5) 500 feet (152 m) maximum Compliance Safety and Emissions FCC Part 15 RoHS Compliant Additional Inf fo RS-232 Baud Rate = 19200 CLI-8000/8000A Front Panel View Item Description A Ethernet Reserved for Future Use B HVAC Relays The HVAC Relays are wired to the HVAC system. Each set of relays or relay bank is referred to as a zone. A maximum of eight zones are supported per TPU. C RS-232 Connect cable from the RS-232 port to a Savant Controller. Communication between the controller and the CLI-8000/8000A is achieved over the RS-232 connection. RS-232 supports 19200 baud. D Station Bus Reserved For Future Use E Console Mini USB (Mini-B) female connector (Serial UART); Debug terminal F DSB/1-Wire The DSB/1-Wire Connector connects to the Data Sensor Bus, which is a serial bus based on the One- Wire protocol. The CLI-THFM1 smart sensor communicates over the Data Sensor Bus through this connection. Up to two smart sensors per zone can be configured with a total of eight per system. G Display/Keypad Monitors and configures the TPU. Use the keypad to scroll through the available menus and configure each zone. H Remote Sensors Indoor, Outdoor, Slab, and Plenum two-wire temperature sensors are connected here. A maximum of two per zone is supported. I Input Power (Access) Remove the power input access screw and remove the associated panel. This will give user access to the power supply board for wiring the 24V AC input power. J Zone LEDs The Zone LED’s indicate which zone has been selected via the keypad for configuration. K Input Power (24V AC) System is powered by 24V AC power source. Power cable is fed through ½” cable restraint (not included) installed at bottom of box. Input power is wired to a two position screw terminal block on the power supply board. L Analog Control Reserved for Future Use M USB The USB port connects to the optional Android™ based tablet. Communication between the tablet and the CLI-8000A version of TPU is achieved through the USB port. N Smart Connect Maintenance functions such as firmware upgrades is done through the Smart Connect connection. Requires SCA-CONF-XX or SCA-CONFL-XX Smart Connect cable. Thermostat Processing Unit (CLI-8000-00 / CLI-8000A-00) Quick Reference Guide Scan this QR code for additional product information. 009-1090-00 CLI-8000-00 CLI-8000A-00 009-1090-00 22414 Savant Confidential and Proprietary 1 of 2
Transcript
Page 1: Thermostat Processing Unit (CLI-8000-00 / CLI-8000A-00 ...dealers.savantav.com/portal/SavantSandbox/Released... · The Savant® CLI-8000 and CLI-8000A eight zone Thermostat Processing

The Savant® CLI-8000 and CLI-8000A eight zone Thermostat Processing Units are at the heart of the Savant® Centralized Climate Control system. Through communications with a number of remote sensors and optional user interfaces, the Thermostat Processing Unit can manage up to eight heating, ventilation, and air conditioning (HVAC) systems. The system is easily integrated with most leading HVAC systems and can be designed as one part of a complete Savant® Control System solution.The CLI-8000 version is configured using the keypad and display located on the front panel. The CLI-8000A version is configured using a climate application loaded onto an Android™ based tablet (Android is a trademark of Google Inc). The tablet, which is installed into the front cover of the TPU, incorporates a touch screen interface with an elegant climate control application for setting up, viewing, and controlling each climate zone independently.Once installed and configured, either system the can be integrated to add monitoring and control through an iOS device such as iPad® or iPod®.

This Quick Reference Guide provides the information necessary to install the CLI-8000/8000A as well as information on wiring to each of the optional and required components of the Savant HVAC solution.

Box Contents(1) CLI-8000 or CLI-8000A (Includes all mating connectors from front panel)(1) Quick Reference Guide (this document)

Related ComponentsSavant® HostSavant® Controller SSC-0008-XX, SSC-0025-XXExternal 120V AC to 24V AC Transformer, PWR-2440-XX

Optional Remote SensorsSavant® SST-TEMP1 - Remote Indoor SensorSavant® SST-OTEMP1 - Remote Outdoor SensorSavant® CLI-THFM1 - Remote Humidity/Temperature Smart SensorSavant® CLI-PLEN1C - Commercial Plenum Sensor (Heat duct sensor) Savant® CLI-PLEN1R - Residential Plenum Sensor (Heat duct sensor) Savant® CLI-SLAB1 - SLAB Sensor (Floor Heating Sensor)

Note: Each zone on the CLI-8000/8000A supports communications with up to four temperature sensors and two humidity sensors.

SpecificationsEnvironmentalEnvironmentalTemperature 32° to 104° F (0° to 40° C)

Humidity 10% to 90% Relative Humidity (non-condensing)

Dimensions and WeightDimensions and WeightHeight 12.17ʺ (31 cm) with cover; 11.05ʺ (28 cm) without cover

Width 15.48ʺ (39.3 cm) with cover; 14.23ʺ (36.1 cm) without cover

Depth 2.81ʺ (7.1 cm) with cover; 2.71ʺ (6.9 cm) without cover

Weight 8.75 lb. / 4.0 kg

PowerPowerPower (Input) 24V AC (40VA) from external transformer

Cable RequirementsCable Requirements

Relay Bank to HVAC system

18 American Wire Gauge (AWG)Standard HVAC wiring (RH, RC, W1, W, Y1, Y2, G, O, Aux)Note: If required, RH and RC can be jumped together.

Cable Requirements (Sensors)Cable Requirements (Sensors)Data Sensor Bus (1-Wire) 24 AWG (Cat 5) 600 feet (182 m) maximum (cumulative)

Remote Sensor 24 AWG (Cat 5) 500 feet (152 m) maximum

ComplianceComplianceSafety and Emissions FCC Part 15

RoHS Compliant

Additional InfoAdditional InfoRS-232 Baud Rate = 19200

CLI-8000/8000A Front Panel View

ItemItem Description

A Ethernet Reserved for Future Use

B HVAC RelaysThe HVAC Relays are wired to the HVAC system. Each set of relays or relay bank is referred to as a zone. A maximum of eight zones are supported per TPU.

C RS-232Connect cable from the RS-232 port to a Savant Controller. Communication between the controller and the CLI-8000/8000A is achieved over the RS-232 connection. RS-232 supports 19200 baud.

D Station Bus Reserved For Future Use

E Console Mini USB (Mini-B) female connector (Serial UART); Debug terminal

F DSB/1-Wire

The DSB/1-Wire Connector connects to the Data Sensor Bus, which is a serial bus based on the One-Wire protocol. The CLI-THFM1 smart sensor communicates over the Data Sensor Bus through this connection. Up to two smart sensors per zone can be configured with a total of eight per system.

G Display/KeypadMonitors and configures the TPU. Use the keypad to scroll through the available menus and configure each zone.

H Remote SensorsIndoor, Outdoor, Slab, and Plenum two-wire temperature sensors are connected here. A maximum of two per zone is supported.

I Input Power(Access)

Remove the power input access screw and remove the associated panel. This will give user access to the power supply board for wiring the 24V AC input power.

J Zone LEDs The Zone LED’s indicate which zone has been selected via the keypad for configuration.

KInput Power(24V AC)

System is powered by 24V AC power source. Power cable is fed through ½” cable restraint (not included) installed at bottom of box. Input power is wired to a two position screw terminal block on the power supply board.

L Analog Control Reserved for Future Use

M USBThe USB port connects to the optional Android™ based tablet. Communication between the tablet and the CLI-8000A version of TPU is achieved through the USB port.

N Smart ConnectMaintenance functions such as firmware upgrades is done through the Smart Connect connection. Requires SCA-CONF-XX or SCA-CONFL-XX Smart Connect cable.

Thermostat Processing Unit(CLI-8000-00 / CLI-8000A-00)

Quick Reference Guide

Scan this QR code for additional product

information.

009-1090-00CLI-8000-00

CLI-8000A-00

009-1090-00 22414 Savant Confidential and Proprietary 1 of 2

Page 2: Thermostat Processing Unit (CLI-8000-00 / CLI-8000A-00 ...dealers.savantav.com/portal/SavantSandbox/Released... · The Savant® CLI-8000 and CLI-8000A eight zone Thermostat Processing

DimensionsThe dimensions for the CLI-8000/8000A are displayed below. The illustration displays the CLI-8000A with the Android™ based tablet installed in the front panel. The CLI-8000 has the same dimensions but the front cover is flat and does not include the cutout.

MountingCan be either surface mounted using a pair of mounting brackets (SMB-8000-XX) or flush mounted between two 16” on center studs. For more information on mounting, refer to the deployment guides for the CLI-8000 (009-1073-XX) or CLI-8000A (009-1154-XX),

Option 1: Mount between studs (Flush Mount)1. Locate two adjacent studs that are 16” on center. If there is drywall, cut to the

dimensions below. 2. Slide between studs. On left and right side there are three mounting holes. Screw

to inside of studs through these holes.

Option 2: Optional Brackets (Surface Mount)1. Screw the mounting brackets to the right and left side of the CLI-8000 using (4)

10-32 x 3/8” FH machine screws.2. The mounting brackets are 16” on center so the TPU can be screwed to two

adjacent studs. Locate two adjacent studs that are 16” on center.3. Screw the TPU to the wall through the drywall and into the studs using

appropriate self tapping drywall screws or equivalent.

Connect Input Power1. Remove the access panel by removing the screw holding down the access panel.2. Locate the ½” electrical knockout just below access panel. Remove knockout and

install electrical clamp.3. Connect the 24V AC from transformer to the two position screw terminal block

under the power input panel.

Note: Use a minimum of 18 AWG wire when connecting the input power.

HVAC Relay WiringThe figure below is the top view of the eleven position screw terminal connector that is plugged into each relay bank. 1. Remove connector from its mate on front panel.2. Insert correct wire into front of plug using information in the table below.3. Tighten screw so that wires are clamped inside the connector.4. Reinsert into the proper relay bank.5. Wire other side to HVAC system.

Relay Description

RH - Red Wired to hot side of transformer on heating equipment.

RC - Red Wired to hot side of transformer on cooling equipment.

W1 - White Wired to stage 1 heat terminal (W1) on HVAC system.

W2 - Black Wired to stage 2 heat terminal (W2) on HVAC system.

Y1 - Yellow Wired to stage 1 cooling terminal (Y1) on HVAC system.

Y2 - Blue Wired to stage 2 cooling terminal (Y2) on HVAC system.

G - Green Wired to fan terminal (G) on HVAC system.

O - Orange Wired to (O) terminal on Heat Pump System. Reversing Valve connection.

C NO NCC = Common TerminalNO = Normally Open, Connects with C when the Relay is ON.NC = Normally Closed, Connects with C when the Relay is OFF.

NOTE: Since there is no standard for wire colors in HVAC, the colors shown in table are typical. Refer to manufacturers documentation to HVAC system before wiring.

Remote Sensor ConnectionsWiring diagram connecting the CLI-THFM1 sensor to the CLI-8000/8000A. Up to two CLI-THFM1 sensors per zone.

In addition to the CLI-THFM1 Smart Sensor described above, other sensors are available. For information on the these sensors, refer to the Quick Reference Guides (QRG’s) for each sensor.

IMPORTANT! Before using the CLI-8000/8000 for the first time, update the firmware to the latest version. Perform the steps outlined in Firmware Upgrade section of the Deployment guide prior to configuring the system.

Additional Documentation Documentation for the CLI-8000/8000A as well as documentation covering the complete Climate Control system are available in the Savant Portal located at dealers.savantsystems.com

Products > Savant Hardware > Climate Control

Thermostat Processing Unit(CLI-8000-00/8000A-00)Quick Reference Guide

009-1090-00CLI-8000-00

CLI-8000A-00

Savant® Centralized Climate Solution CLI-8000/8000A Quick Reference GuideSavant® Centralized Climate Solution CLI-8000/8000A Quick Reference GuideSavant® Centralized Climate Solution CLI-8000/8000A Quick Reference GuideSavant® Centralized Climate Solution CLI-8000/8000A Quick Reference GuideSavant® Centralized Climate Solution CLI-8000/8000A Quick Reference GuideSavant® Centralized Climate Solution CLI-8000/8000A Quick Reference Guide009-1090-00 22414 2 of 2


Recommended