CONTENTS
Product Features and Specifications ..............................................1
Installation Requirement ............................................................ 4
Steps of Installation ………………………………………………..……………………………5
Exploded View ..........................................................................21
Test Run ..................................................................................26
Operation Instruction ................................................................27
Maintenance ........................................................................... 28
Trouble Shooting ..................................................................... 29
Parts List ................................................................................ 30
1
I. PRODUCT FEATURES AND SPECIFICATIONS
FLOORPLATE CHAIN-DRIVE MODEL FEATURES
Model 209 (See Fig. 1)
· Compact design
· Dual hydraulic cylinders, designed and made on ANSI standards, utilizing NOK oil
seal in cylinder
· Self- lubricating UHMW Polyethylene sliders and bronze bush
· Single-point safety release, and dual safety design
· Supersymmetric arms design with 3-stages front arms and 2-stages rear arms
. Stackable rubber pad with 1.5” and 2.5” extension adaptors
MODEL 209 SPECIFICATIONS
Model Style Lifting
Capacity Lifting Time
Lifting Height Overall Height
Overall Width
Width
Between Columns
Minimum
Pad Height
Gross Weight
Motor
209 Floorplate
Chain-drived
4.0T
9,000lbs 45S
1815-1917mm
71 1/2” – 75 1/2”
2742mm
108”
3350mm
132”
2780mm
109 1/2”
90mm
3 1/2”
610Kg 1,345 lbs
2.0/3.0
HP
Fig. 1
2
FLOORPLATE CHAIN-DRIVE TWO POST LIFT
Model 209X (See Fig. 2)
· Compact design
· Dual hydraulic cylinders, designed and made on ANSI standards, utilizing NOK oil seal
in cylinder
· Self- lubricating UHMW Polyethylene sliders and bronze bush
· Single-point safety release, and dual safety design
· Supersymmetric arms design with 3-stages front arms and 2-stages rear arms
. Stackable rubber pad with 1.5”, 2.5” and 5” extension adaptors
MODEL 209X SPECIFICATIONS
Model Style Lifting
Capacity
Lifting
Time Lifting Height
Overall
Height
Overall
Width
Width
Between Columns
Minimum Pad Height
Gross Weight
Motor
209X Floorplate
Chain-drived
4.0T
9,000lbs 49S
1940-2169mm
76 3/8”–85 3/8”
2841mm
111 3/4”
3460mm
136 1/4”
2850mm
112 1/4”
90mm
3 1/2” 675Kg
1,488 lbs
2.0/3.0
HP
Fig. 2
3
Arm Swings View
For Model 209
Fig. 3
Fig. 4
For Model 209X
814mm 1270mm
2513mm
683mm 1159mm
893mm
1350mm
2623mm
1294mm
722mm
4
II. INSTALLATION REQUIREMENT
A. TOOLS REQUIRED
✓ Rotary Hammer Drill (Φ19)
✓ Hammer
✓ Level Bar
✓ English Spanner (12")
✓ Ratchet Spanner With Socket (28#)
Wrench set
✓ Carpenter’s Chalk
✓ Screw Sets
✓ Tape Measure (7.5m)
✓ Pliers
✓ Socket Head Wrench (6#)
Lock Wrench
(10#, 13#, 14#, 15#, 17#, 19#, 24#, 27#)
Fig. 5
5
B. SPECIFICATIONS OF CONCRETE (See Fig. 6).
Specifications of concrete must be adhered to the specification as following.
Failure to do so may result in lift and/or vehicle falling.
1. Concrete must be thickness 150mm minimum and without reinforcing steel bars,
and must be dried totally before the installation.
2. Concrete must be in good condition and must be of test strength 3,500psi
(250kg/cm²) minimum.
3. Floors must be level and no cracks.
Fig. 6
C. POWER SUPPLY
The electrical source must be 3HP minimum. The source cable size must be 2.5mm²
and in good condition of contacting with floor.
III. STEPS OF INSTALLATION
A. Location of Installation
Check and insure the installation location (concrete, layout, space size etc.) is
suitable for lift installation.
B. Use a carpenter’s chalk line to establish installation layout of baseplate (See Fig. 7-8).
Chalk a line
Fig. 7 Model 209
6
C. Check the parts before assembly.
1. Packaged lift and hydraulic power unit (See Fig. 9).
Fig. 9
2. Move the lift aside with fork lift or hoist, and open the outer packing carefully, take off
the parts from upper and inside the column, take out the parts box, check the parts
according to the shipment parts list(See Fig. 10).
Fig. 10
Shipment Parts list Floor cover Parts box Serial No.
Fig. 8 Model 209X
7
3. Loose the screws of the upper package stand, take off the upper column and remove
the package stand.
4. Move aside the parts and check the parts according to the shipment parts list.
4.1 For model 209(See Fig. 11, Fig. 12).
4.2 For model 209X (See Fig. 13, Fig. 14).
Fig. 11
75
75A
Fig. 12
Parts in the parts box
Fig. 14
Parts in the parts box (75A) Fig. 13
8
5. Open the carton of parts and check the parts according to parts box list
(See Fig. 15 & Fig.16).
Model 209
Fig. 15
Model 209X
Fig. 16
9
D. Position powerside columns
Lay down two columns on the installation site parallelly, position the powerside
column according to the actual installation site. Usually, it is suggested to install
powerside column on the front-right side from which vehicles are driven to the lift
(See Fig. 17 & Fig. 18).
Fig. 17 Model 209
Fig. 18 Model 209X
Car-in direction
Powerside column
Offside column
Assemble topplate using M10*35 hex bolt with
nut and lock washer
Car in Direction
Powerside column
Offside column
Assemble topplate using
M10*35 hex bolt with
nut and lock washer
10
E. Connecting the cables
1.Put down columns and then push the carriages higher than chain pulley (See Fig. 19).
2.Push the carriages to the bottom of the columns (See Fig. 20).
Fig. 19
Fig. 20
Push the carriages higher than chain
pulley, cable pass through the top of the
carriages and pass through the hole of the
bottom steel plate of the carriages
Pull out cable
11
F. Position columns (See Fig. 21)
Check the columns plumbness with level bar, and adjusting with the shims if the
columns are not vertical.
G. Fix anchor bolts
1. Prepare anchor bolts (See Fig. 22).
Fig. 22
2. Using the prescribed rotary hammer drill, and drill all the anchor holes and install the
anchor bolts. Then tighten the anchor bolts (See Fig. 23).
Fig. 23
Fig. 21
Model 209: 2780 mm
Model 209X: 2850 mm
Model 209: 3350 mm
Model 209X: 3460 mm
Lock washer Washer Nut
12
H. Lift the carriages up by hand and make them be locked at the same level
(See Fig. 24).
Fig. 24
13
I. Install cable (See Fig. 25)
Fig. 25
The fitting of cable pass through
the hole of the carriages and be
screwed with two cable nuts.
14
J. Assembly oil hose assy. (See Fig. 26).
Fig. 26
15
K. Install hydraulic power unit and oil hose assy. (See Fig. 27).
Tighten all the hydraulic fittings, and fill the reservoir with hydraulic oil.
Note: In consideration of Power Unit’s durability and keep the equipment running
in the perfect condition, please use Hydraulic Oil 46#
Fig. 27
Locking the nut using 19# ratchet spanner
16
View A View B
Safety cable
connecting direction
60
2
L. Install safety device and safety cable (See Fig. 28).
NOTE: 1. Assemble safety cable from offside safety assy.
2. Pay attention to the connecting direction of safety cable.
Fig. 28
17
Floor Cover
Protective rubber sets
M. Assemble floor cover and protective rubber sets (See Fig. 29).
Fig. 29
N. Install lifting arms and adjust the arm locks
1. Install the lifting arms (See Fig. 30 & Fig. 31)
Model 209 Fig. 30
Model 209X Fig. 31
Snap Ring
18
2. Lowing the carriages down to the lowest position, then use the 17# ratchet spanner to
loose the nut (See Fig. 32)
3. Adjust the arm lock as arrow direction (See Fig. 33).
Fig. 33
4. Adjust the moon gear and arm lock to make it to be meshed, then tighten bolts of
arm lock (See Fig. 34).
Fig. 32
Fig. 34
Loose the nut
Arm lock
Moon Gear
19
O. Install Electrical System
Connect the power source on the data plate of Power Unit.
Note: 1. For the safety of operators, the power wiring must contact the floor well.
2. Pay attention to the direction of rotations when using 380V, three phase
motors.
PEAK single phase motor (See Fig. 35).
1. Connecting the two power supply lines (fire wire L and zero wire N) to terminals of
AC contactor marked L1, L2 respectively.
2. Connecting the two motor wires to terminals of AC contactor marked T1, T2.
3. Connecting A2 to L2 of AC contactor.
4. Terminal 4# of control button connected with terminals A1of AC contactor;
Terminal 3# of control button connected with terminals L1of AC contactor.
SPX single phase motor for Model 209/209X (See Fig. 36).
1. Power supply line (fire wire L) connected
with wire of control button.
2. Wire of control button connected
with wire of motor.
3. Power supply line (zero wire N)
connected with wire of motor.
G
L
N
Earth Wire
○5
○6
○4
○3
Fig. 36
Fig. 35
Single phase
20
Three phase motor
1. Circuit diagram (See Fig. 37)
2. Connection step (See Fig. 38)
a. The source wires L1, L2, L3 connected with terminals of AC contactor marked L1,
L2, L3 respectively.
b. Terminals of AC contactor marked L1 connected with terminals 4# of control
button. Terminals A1 of AC contactor connected with terminals 3# of control
button.
Fig. 38
L1 L2 L3
A1
3#
4#
Fig. 38
Three phase
Fig. 37
21
IV. EXPLODED VIEW
Model 209
Fig. 39
22
Model 209X
Fig. 40
23
Cylinders
Fig. 41 Model 209 Fig. 42 Model 209X
SPX MANUAL POWER UNIT 220V/50HZ, single phase
Fig. 43
24
PEAK MANUAL POWER UNIT
Illustration of hydraulic valve for SPX & PEAK hydraulic power unit
a. SPX manual power unit, 220V/50HZ, Single phase (See Fig. 45)
220V/50HZ/1Phase 380V/50HZ/3Phase
Fig. 44
Release valve
Fig. 45
Relief valve
Auxiliary hole Check valve
Protective ring
Capacitor
Oil return port
Auxiliary hole
Oil Outlet
Handle for Release valve
25
b. PEAK manual power unit, 220V/50HZ, Single phase (See Fig. 46)
C. PEAK manual power unit, 380V/50HZ, 3 phase (See Fig. 47)
Oil return port
Fig. 46
Oil Outlet
Relief valve
Fig. 47
Relief valve
Throttle valve
Running capacitor
Start capacitor
Protective ring
Check valve
Release valve
Handle for Release
valve
Throttle valve
Protective ring
Check valve
Handle of release
valve
Release valve
Oil outlet
Oil return port
26
V. TEST RUN
1. Adjust synchronous cable (See Fig. 48)
Press UP button to lift the carriages up to the position of the cable nut higher than
chain pulley. Use wrench to hold the cable fitting, meanwhile
use ratchet spanner to tighten the cable nut.
Make sure two cables are with the same tension
so that two carriage can work synchronously.
Fit the plastic hole cover on the lifting head.
If the carriage does not Synchronize when lifting,
please tighten the cable nut of lower side carriage.
2. Adjust safety cable
Lifting the carriage and lock at the same height, strain the safety cable and then
release a little, and then tighten the cable nuts. Make sure the safety device can
always be worked properly.
3. Adjust the lower speed (Only for PEAK power unit)
You can adjust the lower speed of the lift if needing: Loosen the Fixing Nut of the
throttle valve, and then turn the throttle valve clockwise to decrease the lower speed,
or counterclockwise to increase the lower speed. Do not forget to tighten the fixing
nut after the lower speed adjustment has been done.
Fig. 48
Counterclockwise to increase the down speed
Clockwise to decrease the down speed
Throttle Valve
Fixing Nut
Cable Nut
First Safety
lock
Fig. 49
27
4. Test with load
After finishing the above adjustment, test running the lift with load. Run the lift in
low position for several times first, make sure the lift can rise and lower
synchronously, the Safety Device can lock and release synchronously. And then test
run the lift to the top completely. If there is anything improper, repeat the above
adjustment.
NOTE: It may be vibrated when lifting at start, pls lifting it with load for several
times, the air would be bleeded and the vibration would be disappeared
automatically.
Fig. 50 Hydraulic System
VI. OPERATION INSTRUCTIONS
Please read the safety tips carefully before operating the lift
To lift vehicle
1. Keep clean of site near the lift;
2. Position lift arms to the lowest position;
3. To shortest lift arms;
4. Open lift arms;
5. Position vehicle between columns;
28
6. Move arms to the vehicle’s lifting point;
Note: The four lift arms must at the same time contact the vehicle’s lifting point
where manufacturers recommended
7. Press the UP button until the lift pads contact underside of vehicle totally. Recheck
to make sure vehicle is secure;
8. Continue to raise the lift slowly to the desired working height, ensuring the balance
of vehicle;
9. Push lowering handle to lower lift onto the nearest safety. The vehicle is ready to
repair.
To lower vehicle
1. Be sure clear of around and under the lift, only leaving operator in lift area;
2. Press the button of UP to raise the vehicle slightly, and then release the safety
device, lower vehicle by pushing lowering handle.
3. Open the arms and position them to the shortest length;
4. Drive away the vehicle.
5. Turn off the power.
VII. MAINTENANCE SCHEDULE
Monthly:
1. Re-torque the anchor bolts to 80-117 Nm;
2. Check all connectors, bolts and pins to insure proper mounting;
3. Lubricate cable with lubricant;
4. Make a visual inspection of all hydraulic hoses/lines for possible wear or leakage;
5. Check Safety device and make sure proper condition;
6. Lubricate all Rollers and Pins with 90wt. Gear oil or equivalent;
Note: All anchor bolts should take full torque. If any of the bolts does not function for
any reason, DO NOT use the lift until the bolt has been replaced.
Every six months:
1. Make a visual inspection of all moving parts for possible wear, interference or
damage.
2. Check and adjust as necessary, equalizer tension of the cables to insure level lifting.
3. Check columns for plumbness.
4. Check Rubber Pads and replace as necessary.
5. Check Safety device and make sure proper condition.
29
VIII.TROUBLE SHOOTING
TROUBLE CAUSE REMEDY
Motor does not
run
1. Button does not work
2. Wiring connections are not in good
condition
3. Motor burned out
4. AC contactor in damage
1. Replace button
2.Repair all wiring connections
3. Repair or replace motor
4. Replace or replace
Motor runs but
the lift is not
raised
1. Motor runs in reverse rotation
2. Gear pump out of operation
3. Release valve in damage
4. Relief valve or check valve in damage
5. Low oil level
1.Reverse two power wire
2.Repair or replace
3. Repair or replace
4.Repair or replace
5.Fill tank
Lift does not
stay up
1. Release valve out of work
2. Relief valve or check Valve leakage
3. Cylinder or fttings leaks
Repair or replace
Lift raises
slowly
1. Oil line is jammed
2. Motor running on low voltage
3. Oil mixed with air
4. Gear Pump leaks
5. Overload lifting
1. Clean the oil line
2. Check electrical system
3. Fill tank
4. Replace pump
5. Check load
Lift can not
lower
1. Safety device are locking.
2. Release valve in damage
3. Safety cable broken
4. Oil system is jammed
1. Release the safeties
2. Repair or replace
3. Replace
4. Clean the oil system
30
IX. PARTS LIST FOR MODEL 209 and 209X
A. Parts For Model 209 (See Fig. 39, Fig. 6)
Item Part# Description Qty. Note
1 205001A Powerside column 1
2 209011 Plastic pulley 1
3 209010 Snap ring 2
4 209008 Safety cover 2
5 209009 Cup head bolt 4
6 206006 Washer 2
7 206023A Hex nut 2
201 209002 Manual power unit 1
9 209006 Safety pin 2
10 209007 Safety spring 2
11 203002 Powerside safety lock 1
12 209012 Hair pin 8
13 203015 Safety block (Main) 1
14 209003 Hex bolt 4
15 209004 Rubber ring 4
16 209005 Self locking nut 8
17 205002 Floor cover 1
18 209052B Stackable Adapter (2.5”) 4
19 209051B Stackable Adapter (1.5”) 4
20 201039B Lifting Arm-Rear 2
20A 201050 Outer Arm-Rear 2
20B 201051A Inner Arm-Rear 2
21 201046A Rubber Pad Assy. 4
21A 420138 Socket bolt 4
21B 209134 Rubber Pad 4
21C 680030C Rubber Pad Frame 4
22 209057 Small pulley 4
23 209056 Self locking nut 2
24 201043A Lifting Arm-Front 2
24A 201047 Outer Arm-Front 2
24B 201048 Middle Arm-Front 2
24C 201049A Inner Arm-Front 2
25 201010 Chain connector 4
26 201009A Chain 2
27 201008A Hydraulic cylinder 2
28 201007 Pin for chain pulley 2
29 203004A Bronze bush for chain pulley 4
30 201006 Chain pulley 2
31 201005 Split pin 2
32 201004 Chain pulley assy. 2
33 205003 Powerside Carriage 1
34 206044 Slider 16
35 209016 Carriage plastic cover 2
36 206045 Protective rubber 2
31
Item Part# Description Qty. Note
37 206046 Self-tapping screw 4
38 209020 Plastic ball 4
39 209021 Hex nut 8
40 209022 Washer 10
41 209023A Arm lock 4
41A 210041 Limit Ring 4
42 209024 Arm lock bar 4
43 209025 Hair pin 4
44 209026 Spring 4
45 209027 Protective rubber set 4
46 209038 Hex bolt 6
47 209039 Lock washer 10
48 205004 Offside carriage 1
49 209035 Moon gear 4
50 209032 Socket bolt 12
50A 209034 Lock washer 12
50B 209033 Washer 16
51 209031 Snap ring 4
52 209030A Lifting Arm Pin 4
53 205005 Connecting Bar 2
54 209043 Hex Bolt 4
55 209046 Hex Bolt 4
56 205006 Top plate 2
57 209045 Big Pulley 2
58 209057A Bronze bush for pulley 6
59 205007A Offside column 1
60 209049 Plastic pulley 3
61 203012 Offside safety lock 1
62 203013 Coupling 2
63 203014 Safety Block (Secondly) 1
64 203018 Socket Bolt 4
65 203016 Snap Ring 4
65A 209051A Stackable Adapter(1.5”) 4
65B 209052A Stackable Adapter(2.5”) 4
65C 209053A Stackable Adapter(5”) 4
66 209059 Anchor bolt 12
Oil Hose, Fitting & Cable (See Fig. 25-28, Fig.11,12)
67 209060 900 Fitting for Power Unit 1
68 201021 Oil Hose 1
69 201022 T-Fitting 1
70 205008 Oil Hose 1
71 201020 900 Fitting 1
72 205009 Cable 2
73 209066 Cable Nut 4
74 205010 Safety Cable 1
75 205500A Parts Box 1
32
Parts For Hydraulic Cylinder (See Fig. 41)
Item Part# Description Qty. Note
27-1 201027A Piston Rod 2
27-2 201028 Piston 2
27-3 206069 O-Ring 2
27-4 201029 Support Ring 2
27-5 201030 Y-Ring 2
27-6 201031 O-Ring 2
27-7 206071 Hex Nut 2
27-8 201037 Adjustment Tube 2
27-9 209078 Dust Seal 2
27-10 201032 O-Ring 2
27-11 201033 Head Cap 2
27-12 201034 Bleeding Plug 2
27-13 201035 O-Ring 2
27-14 201036A Bore Weldment 2
B. Parts For Model 209X (See Fig. 40, Fig. 6)
Item Part# Description Qty. Note
1 203001A Powerside column 1
2 209011 Plastic Pulley 1
3 209010 Snap Ring 2
4 209008 Safety Cover 2
5 209009 Cup Head Bolt 4
6 206006 Washer 2
7 206023A Hex Nut 2
201 209002 Manual Power Unit 1
9 206002 Safety Pin 2
10 209007 Safety Spring 2
11 203002 Powerside Safety Lock 1
12 209012 Hair Pin 8
13 203015 Safety Block (Main) 1
14 209003 Hex Bolt 4
15 209004 Rubber Ring 4
16 209005 Self locking nut 8
17 203003 Floor Cover 1
18 201046A Rubber Pad Assy. 4
18A 420138 Socket bolt 4
18B 209134 Rubber Pad 4
18C 680030C Rubber Pad Frame 4
19 209039 Lock Washer 10
20 209038 Hex Bolt 6
21 209057 Small Pulley 4
22 209056 Self locking nut 2
33
Item Part# Description Qty. Note
23 201010 Chain Connector 4
24 203005 Chain 2
25 201008 Hydraulic Cylinder 2
26 201007 Pin For Chain Pulley 2
27 203004 Chain Pulley 2
27A 203004A Bronze bush for Chain Pulley 4
28 201005 Split Pin 2
29 201004 Chain Pulley Assy. 2
30 203007 Powerside Carriage 1
31 206044 Slider 16
32 209016 Carriage Plastic Cover 2
33 206045 Protective Rubber 2
34 206046 Self-tapping Screw 4
35 209020 Plastic Ball 4
36 209021 Hex Nut 8
37 209022 Washer 10
38 209023A Arm lock 4
38A 201041 Limit Ring 4
39 209024 Arm Lock Bar 4
40 209025 Hair Pin 4
41 209026 Spring 4
42 209027 Protective Rubber Set 4
43 209029A Lifting Arm - Front Right 1
43A 209137 Outer Arm - Front Right 1
43B 206088 Middle Arm - Front Right 1
43C 206089A Inner Arm - Front Right 1
44 209036A Lifting Arm - Front Left 1
44A 209138 Outer Arm - Front Left 1
44B 206093 Middle Arm - Front Left 1
44C 206089A Inner Arm - Front Left 1
45 203044A Lifting Arm - Rear Left 1
45A 203046 Outer Arm - Rear Left 1
45B 203047A Inner Arm - Rear Left 1
46 203008 Offside Carriage 1
47 203045A Lifting Arm - Rear Right 1
47A 203048 Outer Arm - Rear Right 1
47B 203049A Inner Arm - Rear Right 1
48 209035 Moon Gear 4
49 209033 Washer 20
50 209034 Lock Washer 12
51 209032 Socket Bolt 12
52 209030 Arm Pin 4
53 203009 Connecting Bar 2
54 209043 Hex Bolt 8
34
Item Part# Description Qty. Note
55 209046 Hex Bolt 4
56 203010 Top plate 2
57 209045 Big Pulley 2
58 209057 Bronze Bush For Pulley 6
59 203011A Offside column 1
60 209049 Plastic Pulley 3
61 203012 Offside Safety Lock 1
62 203013 Coupling 2
63 203014 Safety Block (Secondly ) 1
64 203018 Socket Bolt 4
65 203016 Snap Ring 4
65A 209051B Stackable Adapter (1.5”) 4
65B 209052B Stackable Adapter (2.5”) 4
65C 209053B Stackable Adapter (5”) 4
66 209059 Anchor bolt 12
Oil Hose, Fitting & Cable (See Fig. 25-28, Fig.13,14)
67 209060 900 Fitting for Power Unit 1
68 201021 Oil Hose 1
69 201022 T-Fitting 1
70 203019 Oil Hose 1
71 201020 900 Fitting 1
72 203020 Cable 2
73 209066 Cable Nut 4
74 203021 Safety Cable 1
75A 203501A Parts Box 1
Parts For Hydraulic Cylinder (See Fig. 42)
25-1 201027 Piston Rod 2
25-2 201028 Piston 2
25-3 206069 O-Ring 2
25-4 201029 Support Ring 2
25-5 201030 Y-Ring 2
25-6 201031 O-Ring 2
25-7 206071 Hex Nut 2
25-8 201037 Adjustment Tube 2
25-9 209078 Dust Seal 2
25-10 201032 O-Ring 2
25-11 201033 Head Cap 2
25-12 201034 Bleeding Plug 2
25-13 201035 O-Ring 2
25-14 201036 Bore Weldment 2
35
PARTS LIST FOR MANUAL POWER UNIT
Parts For SPX Manual Power Unit 220V/50HZ/1Phrase (See Fig. 43)
Item Part# Description Qty. Note
201-1 209082 Motor 1
201-2 209109 Protective Ring 1
201-3 209083 Motor Connecting Shaft 1
201-4 209084 Valve Body 1
201-5 209085 Relief Valve 1
201-6 209086 Lock Washer 4
201-7 209087 Socket Bolt 4
201-8 209088 Inlet Pipe 1
201-9 209089 O-Ring 1
201-10 209090 Filter 1
201-11 209091 Hex bolt 4
201-12 209092 Reservoir 1
201-13 209093 Bolt 2
201-14 209094 Cover of Capacitor 1
201-15 209095 Capacitor 1
201-16 209096 Rubber Gasket 1
201-17 209097 Hex bolt 1
201-18 209098 Cover of Motor Terminal Box 1
201-19 209099 Push Button 1
201-20 209110 Oil Return Port 1
201-21 209100 Oil Outlet 1
201-22 209101 Release Valve 1
201-23 209102 Handle For Release Valve 1
201-24 209103 Washer 1
201-25 209104 Hex Nut 1
201-26 209105 Check Valve 1
201-27 209106 Gear Pump 1
201-28 209107 Oil Return Pipe 1
201-29 209108 Filler Cap 1
36
Parts For PEAK Manual Power Unit 220V/50HZ/1Phase (See Fig. 44)
Item Part# Description Qty. Note
201A-1 209082A Motor 1
201A-2 209109 Protective Ring 1
201A-3 209112 AC contactor 1
201A-4 209083A Motor Connecting Shaft 1
201A-5 209084A Valve Body 1
201A-6 209085A Relief Valve 1
201A-7 209113 Throttle valve 1
201A-8 209086A Lock Washer 4
201A-9 209087A Socket Bolt 4
201A-10 209088A Inlet Pipe 1
201A-11 209089A O-Ring 1
201A-12 209090A Filter 1
201A-13 209091A Socket bolt 4
201A-14 209092A Reservoir 1
201A-15 209093A Cup Head Bolt with washer 4
201A-16 209094A Cover of Capacitor 2
201A-17 209095A Start Capacitor 1
201A-17A 209095B Run Capacitor 1
201A-18 209096A Rubber Gasket 2
201A-19 209097A Cup Head Bolt with washer 2
201A-20 209098A Cover of Motor Terminal Box 1
201A-21 209099A Push Button 1
201A-22 209110A Oil Return Port 1
201A-23 209100A Oil Outlet 1
201A-24 209105A Check Valve 1
201A-25 209101A Release Valve 1
201A-26 209102A Handle For Release Valve 1
201A-27 209103A Washer 1
201A-28 209104A Hex Nut 1
201A-29 209106A Gear Pump 1
201A-30 209107A Oil Return Pipe 1
201A-31 209108A Filler Cap 1
37
Parts For PEAK Manual Power Unit 380V/50HZ/3Phase (See Fig. 44)
Item Part# Description Qty. Note
201B-1 209118A Motor 1
201B-2 209109 Protective Ring 1
201B-3 209112 AC contactor 1
201B-4 209083A Motor Connecting Shaft 1
201B-5 209084A Valve Body 1
201B-6 209085A Relief Valve 1
201B-7 209113 Throttle valve 1
201B-8 209086A Lock Washer 4
201B-9 209087A Socket Bolt 4
201B-10 209088A Inlet Pipe 1
201B-11 209089A O-Ring 1
201B-12 209090A Filter 1
201B-13 209091A Socket bolt 4
201B-14 209092A Reservoir 1
201B-15 209097A Cup Head Bolt with washer 2
201B-16 209098A Cover of Motor Terminal Box 1
201B-17 209099A Push Button 1
201B-18 209110A Oil Return Port 1
201B-19 209100A Oil Outlet 1
201B-20 209105A Check Valve 1
201B-21 209101A Release Valve 1
201B-22 209102A Handle For Release Valve 1
201B-23 209103A Washer 1
201B-24 209104A Hex Nut 1
201B-25 209106A Gear Pump 1
201B-26 209107A Oil Return Pipe 1
201B-27 209108A Filler Cap 1
38
72220302
04/2013