ASSEMBLY INSTRUCTIONS
Stilford Professional Meeting Room Table 1200,1500 and 1800
STPMR12WEK / STPMR12OAK / STPMR12WNK / STPMR15WEK / STPMR15OAK / STPMR15WNK / STPMR18WEK / STPMR18OAK / STPMR18WNK
1/17
This design and instruction booklet is subject to copyright.
www.officeworks.com.au
For spare parts or hardware call (03) 9310 3011 or email [email protected]
2 Cartons
2/17
Important
Estimated Assemble Time: 50min
Please check you have all hardware before assembling.
If you are missing any hardware, please contact Kyvas on (03) 9310 3011
or email [email protected]
Please ensure you have the item, required hardware part and quantity.
Please retain your receipt as proof of purchase to validate your warranty.
NOTE
Do not tighten screws before all screws are in the right place.
Do not use this product unless all bolts, screws and knobs are firmly secured.
Check that all bolts, screws and knobs are securely tightened at least
every 4
CAUTION
months.
If parts are missing, broken, damaged or worn stop using the product until
all repairs are made using manufacturer authorised parts.
Keep children and animals away from the assembly area.
This furniture contains small parts that could cause choking if swallowed.
Keep all plastic wrapping materials away from babies and children to
avoid danger of suffocation.
This item is not for outdoor use - unless stated otherwise.
Failure to follow these warnings could result in serious injury.
WARNING
CHILDREN MUST BE SUPERVISED.
DANGER
Officeworks Ltd.丨236-262 East Boundary Road 丨Bentleigh East VIC 3165 丨AUSTRALIA
Tools Required
CAUTION:
.
.
.
.
.
.
.
.
.
.
.
.
.
Do not use tools other than those required, as this can damage
your new item.
People Required General AdviceCustomer Service Contact Details
Assemble On A Clean Flat
Surface
More Than One Person Is Required
To Safely Assemble The Item
Spare Parts & Hardware
(03) 9310 3011
3/17
6
3
2
4
4
5
5
2
3
3
3
1
Part Overview
4/17
2
2pcs
3
4pcs
4
2pcs
Part List
5 6
1
Parts located in Carton -
STPRMR12WE / STPRMR12OA / STPRMR12WN /STPRMR15WE / STPRMR15OA / STPRMR15WN /STPRMR18WE / STPRMR18OA / STPRMR18WN
Parts located in Carton - STPRTB128B
2pcs 1pc
1pc
5/17
Hardware Pack located in Carton - STPRTB128B
Hardware List
E
（M8 x 80 mm）
X 4pcs
F GDC
（M10 x 70 mm）
X 2pcs
（M10 x 50 mm）
X 2pcs
（M8 x 50 mm）
X 4pcs X 4pcs
（M8 x 16 mm）
X 1pc
Allen Key
M10-size
X 1pc
Allen Key
M8-size
X 1pc X 4pcs
J LIH
6/17
For missing hardware, please contact Kyvas on (03) 9310 3011 or email [email protected]
Hardware List
K M
A
Other Hardware located in Carton - STPRTB128B
Hardware A located in Carton -
STPRMR12WE / STPRMR12OA / STPRMR12WN /STPRMR15WE / STPRMR15OA / STPRMR15WN /STPRMR18WE / STPRMR18OA / STPRMR18WN
（M6 x 16 mm）
X 16pcs
X 4pcsX 8pcs
Connector Adjust Feet
Step 1
M
M
3
4X
M
4pcs
C
H
J
2
4
C HJ
2pcs 1pc 1pc
2X
Step 3
4
3
3
EE
E E
I
J
E IJ
4pcs 1pc 1pc
7/17
Step 2
2X
Note: Do not tighten
the screw E fully
until you have
completed Step 8 or
Step11 or Step14 !
Assembly
F
F
D
4
Step 5
H IJ
1pc 1pc
F
4pcs
D
2pcs 1pc
8/17
F
F
D
5
5
4
6
F
F
D
I
H
J
90°
90°
Note: Tighten
the screw G fully after you
confirmed the part 5 & 6
are at right (vertical) angle.
Step 4
G IJ
4pcs 1pc 1pc
I
G
I
G
J
G
6
5
5
J
I
J
9/17
12-13
Option 3, size: W1800*D1200*H750mm
Note: Assemble 3 different table sizes by adjusting the frame.
Option 1, size: W1200*D1200*H750mm
10-11
14-15
10/17
Step 6
1200
1200
Note: Adjust part 6 to be suitable for the table top
by below pre-drilled (marked in black)
A
K
K
4pcs
A
8pcs
A
K
A
K
A
K
1
L
L
L
4pcs
A
K
For W1200*D1200*H750mm Table
1
6
11/17
Step 7
K
4pcs
A
8pcs
A
K
A
K
A
KA
K
1
EE
C
Note: Tighten the screw C & E fully
after adjusting the leg at correct position.
I
Step 8
H I
1pc 1pc
J
1pc
For W1200*D1200*H750mm Table
For W1200*D1200*H750mm Table
A
K
I
12/17
Step 9
1200
1500
A
K
A
K
A
K
A
K
L
L
1
K
4pcs
A
8pcs
L
4pcs
A
K
1
6
For W1500*D1200*H750mm Table
Note: Adjust part 6 to be suitable for the table top
by below pre-drilled (marked in black)
Step 10
13/17
A
K
A
A
A
1
EE
C
K
4pcs
A
8pcs
Step 11
H I
1pc 1pc
J
1pc
I
K
K
K
For W1500*D1200*H750mm Table
A
K
Note: Tighten the screw C & E fully
after adjusting the leg at correct position.
For W1500*D1200*H750mm Table
I
14/17
A
K
A
K
A
K
A
K
Step 12
L
L
K
4pcs
A
8pcs
L
4pcs
1200
1800
For W1800*D1200*H750mm Table
A
K
Note: Adjust part 6 to be suitable for the table top
by below pre-drilled (marked in black)
1
6
1
15/17
Step 13
A
A
A
A
K
4pcs
A
8pcs
H I
1pc 1pc
J
1pc
Step 14
EE
C
I
K
K
K
K
For W1800*D1200*H750mm Table
1
A
K
Note: Tighten the screw C & E fully
after adjusting the leg at correct position.
For W1800*D1200*H750mm Table
I
Maximum Load Capacity: 50kg
16/17
is now complete and ready for use
Your Stilford Professional Meeting Room Table 1200,1500 and 1800
Care Advice
Care Instructions - PVC/ Melamine Finish Desk
Keep away and protect from direct sunlight and heat.
Do not place sharp materials(knife, fork, etc) directly onto your furniture as sharp
material may scrape and damage the finish.
Clean up spills quickly. Water left over a prolonged period of time may cause
damage. Alcohol, perfume, nail polishes, aftershave and some medication may
cause severe finish damage if not cleaned immediately.
Use a clean, soft, dry, lint free absorbant cloth to clean your furniture. Do not use
any detergent as they may contain ingredients that may react and damage the finish.
Clean, check and tighten all parts regularly.
.
.
.
.
.
Safety Warning
.
CAUTION -This product is intended to hold the maximum weight indicated.
Exceeding the maximum weight will result in instability and may cause injury.
17/17
Thank you for your purchase. Please retain your receipt to validate warranty.
If you would like to know more about our furniture products, please visit www.officeworks.com.au
Warranty 15 years
Product Warranty – valid for Australian customers only
Officeworks Ltd warrants that this product will be free from defects and work as intended
for 15 years from the date of purchase by the original customer.
If the product has any defects or does not work as intended during the Warranty Period,
Officeworks will, at its election and at its expense, repair or replace the product.
This warranty does not apply:
.
to cosmetic damage;
to damage caused by consumables used in connection with the product (such as
cleaning products);
where the product has not been used in accordance with all provided instructions;
to damage arising from fair wear and tear;
where the product has not been subject to reasonable use;
where the product has been intentionally or negligently damaged;and /or
if the customer has attempted to repair the product.
.
.
.
.
.
.
To make a claim under this warranty, please return your product with your receipt or proof
of purchase to your nearest Officeworks store or contact 1300 633 423.
This warranty if provided in addition to any rights you may be entitled to under the
Competitions & Consumer Act 2010.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
RECYCLE
