Timber Pontoon with Concrete
Floats
www.topmarine.eu www.topmarine.eu
L
W
L
WTimber Pontoon with Concrete Floats
END CONNECTION T-CONNECTION L-CONNECTION
L
W
L
W
SIDE CONNECTION
3D FIXING SET- Robust hot dip galvanized fixing
set connects concrete floats and timber deck into one;
- Designed to withstand bending and twisting loads.
CHAIN MOORING SYSTEM- Robust chain fixing set hot dip galvanized.
SAFETY EQUIPMENT- SOS Pedestal;- Safety Ladder.
SERVICE PEDESTAL- Electricity supply for boats;- Water supply for boats;- Lighting for the floating pontoon.
MOORING EQUIPMENT- T-bollard mooring;- Mooring ring.
PILE MOORING SYSTEM- An alternative solution for chain
mooring;- Has been designed for piles
Ø300-400 mm;- The design pile load is 20 kN;- Large and robust construction;- Flexible rubber joints.
GANGWAY- Metal gangway;- Timber gangway.
BOAT BOOMS- Boat Booms
with rubber or hinge connection;
- With or without timber decking.
FENDER- Protects mooring fingers or
timber pontoons against impacts (colour: white).
TIMBER DECKING - Planed anti-slip
blanks 28x120 mm;- Strength C16
according to EN 338 standard;
- Impregnated (vacuum pressure method) softwood decking, class: HC4.
TIMBER FRAME- Double sided planed
timber beam 70x195 mm;
- Strength C24 according to EN 338 standard;
- Impregnated (vacuum pressure method), class: HC4.
- Built to required length without visible joints;
- All bolts and fittings are hot dip galvanized.
SERVICE DUCTS AND CABLE TRAY- Internal, not visible;- Can be installed on both sides or in the
middle.
CONCRETE FLOATS- Hydrotechnical fiber reinforced
concrete C40/50: watertight W6, environmental class XS2, frost resistance XF4 and KK4;
- Reinforcement 6mm fully hot dip galvanized C4 according to ISO 1461 standard;
- Expanded polystyrene: density 19 kg/m³, strenght ≥100 kPa, water absorption ≤3%.
MOORING FINGER- Mooring Fingers with
rubber connection.
Tule 21, Saue 76505 [email protected]
Top MarinePh +372 5304 4000Fax +372 656 0520
Representative:
Timber Pontoon with Concrete Floats
Technical Data of the Timber Pontoon with Concrete Floats
Timber Pontoon Good stability, suitable for year-round use
Intended useAs landing stages, for floating platforms, for floating houses and for other on sea structures
Connection options End connection, side connection, L-connection, T-connection
Structural designHydrotechnical fiber reinforced concrete with EPS inside floats, impregnated softwood timber decking, built to required length without visible joints
Mooring system Mooring by chain or elastic rope. Mooring by piles
AccessoriesMooring rings, mooring bollards, mooring fingers, boat booms, fenders, service ducts, safety equipment, swim ladders
Technical data of pontoon
Item code 03 10 00 03 20 00 03 30 00
Dimensions of pontoons (m)
W 2.4 3.2 2.4
L 12.0 12.0 8.0
H 1.0 1.0 1.0
Number of floats (pc) 2 3 2
Freeboard (m) 0.644 0.657 0.515
Weight of the pontoon (kg) 5200 7507 3008
Designed load capacities (kN/m²) 1.85 2.16 0.76
Allowed max wave height 0.3 m
Allowed perpendicular velocity 1 m/sec
Allowev icing/ freezing No ice movement allowed
Mooring systems
Chain Ø16 mm
Concrete anchors 1000 kg
Pile Ø300...400 mm, 20 kN
Boat mooringMooring buoys, Boat booms, Mooring fingers, Mooring
rings, Mooring bollards
Max boat dimensions Boat max length 12.2m (40 feet)
Technical data of concrete float
Item code 03 70 00 03 70 00 03 50 00
Dimensions of concrete floats (m)
W 2.38 3.12 2.38
L 3.12 2.38 1.32
H 0.71 0.71 0.71
Weight of float (kg) 2009 2009 1098
Designed load capacities of float (kN) 32.5 32.5 11.3
Revision date 1 January 2016
Top Marine is a continuously developing firm and may at its sole discretion revise or amend this product catalogue without further notice.