TITAN
A HEAVY DUTY TRUCK FOR HEAVY DUTY JOBS
Developed to take the hard work out of the tough jobs,
the Mack Titan is best suited for those heavy and
challenging loads.
Perfect for road train, triple and quad applications, where payload
is high and the distances are demanding.
Equipped with the Mack MP10 engine (the most powerful engine Mack
has to offer) coupled with mDRIVE (our automated manual transmission),
you’ll have all the power and comfort you need.
FEATURES » The ultimate truck for the toughest
conditions
» Perfect for severe heavy duty and demanding haul applications
» The Mack MP10 engine delivers up to 685Hp and 2,300 lb-ft torque
» mDRIVE automated manual transmission takes all the effort out of gear changes
» Mack PowerLeash offers ultimate braking control under demanding conditions
» Mack Grade Gripper – hill start assist
» Quiet and comfortable cab
» Great fuel economy and low emissions
Designed and built in Australia for Australian conditions
TITAN 52” HIGHRISE ROADTRAIN
TITAN 60” MIDRISE 2 TRAILER ROADTRAIN
TITAN HD 46” MID RISE 8X6 LOWLOADER
FAN
» 813mm (32”) 11-blade nylon fan
RADIATOR
» NL1 Heavy Duty, Frontal area 1,757in²
EXHAUST
» Single RHS frame mounted catalyst with stainless steel heat shield» Outlet twin 152mm (6”) vertical exhaust (Day Cab/Sleeper Cab)» Right hand horizontal outlet exhaust (Day Cab)» Exhaust tip height above ground 3.5mtr» Exhaust tip height above ground 4.2mtr (optional)
TRANSMISSION
» Manual and Automated Manual Transmissions (Refer Transmission Chart)
» Transmission oil cooler
CLUTCH
» Eaton 394mm (15.5”) Easy Pedal with VCT Plus» Eaton ‘SOLO’ with VCT Plus (CA)» SACHS 430mm (17”) Single Plate (mDRIVE only)» Air assist clutch release
DRIVELINE
» Spicer 10 series» SPL Maintenance Free (option)» C2060 Compact series
PTO OPTIONS
» mDRIVE transmission mounted – DIN or Flange (optional)» Rear of engine (PTO - DIN or Flange) (CA)» Prep kit, switch, wiring and software (mDRIVE) (optional)
ENGINE
» Mack MP10 16 litre, 600Hp – 685Hp (Ref Engine chart)» Selective Catalytic Reduction (SCR)» Emission Level Euro5 (ADR80-03)
ENGINE BRAKE
» Advanced PowerLeash engine brake » Engine retarding power up to 570Hp (425kW)
AIR INTAKE & FILTER
» Donaldson 279mm (11”) single dry type element, dual canisters mounted under the cab
» Painted steel dust extractors (optional) and external air intakes mounted in front of the cabin ‘A’ pillars
FILTERS
» 2 full flow and 1 bypass engine mounted oil filters» 2 step dual engine mounted fuel filters / water separator
AIR COMPRESSOR
» Twin cyl 900 litres/min WABCO compressor
AIR DRYER
» Bendix AD-IS air dryer
ALTERNATOR
» Leece Neville 12volt/160Amp Brushed» Leece Neville 12volt/160Amp Brushless (optional)» Leece Neville 12volt/185Amp Brushless (optional)» Leece Neville 12volt/200Amp Brushed (optional)
STARTER
» MELCO 12volt electric starter» Key type start & stop
MAKE MODEL MAX TORQUE CAPACITY FWD GEARS REV GEARS LO/HI TYPE
Mack (mDrive) ATO3112D 2,350ft-lbs(600Hp and 685HP)
12 2 11.73 / 0.78 Automated Manual
Eaton RTLO-22918B (CA) 2,250ft-lbs (600HP only) 18 2 14.40 / 0.73 Manual
TRANSMISSION SPECIFICATIONS
TITAN
MAKE MODEL HORSEPOWER MAX TORQUE LITRES CYL /
VALVES EMISSION
Mack MP10 600 2,065ft-lbs 16ltr 6 / 24 SCR / ADR80/03
Mack MP10 685 2,300ft-lbs 16ltr 6 / 24 SCR / ADR80/03
ENGINE SPECIFICATIONS
ENGINE & TRANSMISSION
REAR AXLES
» Mack, Meritor and Dana axle options (Refer Drive Axle Chart)» Ratings 21 to 26 tonne
REAR SUSPENSION
» Air and mechanical spring options (Refer Drive Axle Chart)» Ratings 21 to 26 tonne
INTER-AXLE/WHEEL LOCKS
» DCDL one axle only (vendor axles only)» DCDL’s on both axles (optional)» Mack Power Divider (standard with Mack axles)
WHEELS
» 10 stud 8¼” (285mm) PCD steel disc » 10-stud options:
8¼” (285mm PCD) machine buff / polished alloy or DURABRIGHT alloy disc 9” (285mm PCD) polished or DURABRIGHT alloy disc *335mm PCD options available on selected axle combinations
TYRES
» Bridgestone / Michelin tyres
FRONT AXLE
» Mack FXL with unitised hubs (Refer Steer Axle Chart)» Axle position: Mid Axle Forward: 1,058mm Bumper to Front Axle
FRONT SUSPENSION
» 1,321mm (52”) long springs (Refer Steer Axle Chart)
BRAKES
» Drum and disc brake options» Front and rear automatic slack adjusters» ABS or (optional) ABS with Traction Control» Grade Gripper - hill start assist (standard with mDRIVE)» Road Stability Advantage (ESP - Electronic Stability Program)
– optional
STEERING GEAR
» Sheppard SD110» Steering ratio 16.9:1 » Steering Damper
MAKE MODEL CAPACITY RATIOS SUSPENSION
Mack S652 65,000lbs (29t) 4.36, 4.60 AD260
Mack RTH2610B (Hub Reduction) (CA) 57,000lbs (26t) 4.12, 4.55, 5.41 MIL-X
Mack RTH2610B (Hub Reduction) 57,000lbs (26t) (CA) 3.76, 4.12, 4.55 MACK Air
Mack NAS369 (tri-drive) (CA) 69,000lbs (31t) 5.46 AD369
Mack NAS397 (tri-drive) (CA) 97,000lbs (44t) 4.60, 5.22 AD390
Meritor RT52-185 52,000lbs (24t) 3.58, 3.73, 4.10, 4.30 AD260/MIL-X
Dana D52-190 52,000lbs (24t) 3.58, 3.73, 3.91, 4.10, 4.30, 4.56 AD260
Sisu FR2P32S (CA) 70,500lbs (32t) 4.68, 5.56 AD260
Sisu FR3P48S (tri-drive) (CA) 96,000lbs (48t) 4.68, 5.56 AD390
Note: Other ratios available via (CA) - Customer Adaptation
DRIVE AXLE SPECIFICATIONS
AXLES, SUSPENSIONS & BRAKES
MAKE MODEL CAPACITY SUSPENSION
Mack FXL 16.5 16,500lbs (7.5t) CLX (P3,M8)
Mack FXL 18 18,000lbs (8.2t) CLX (M7)
Mack FXL 20 (CA) 20,000lbs (9t) CLX (P4,H8)
Note: Parabolic Standard Duty (P), Multileaf Standard Duty (M), Multileaf Heavy Duty (H) - Number = Leaf Qty
STEER AXLE SPECIFICATIONS
BORN READY.
*Model shown is for illustration purposes only. Contact your Authorised Dealer for details of current options available.
CHASSIS
» Advantage 300mm x 90mm x 9.5mm† 184,000psi/RBM 2,240,000in lb
» Advantage 300mm x 90mm x 11.1mm† 212,000psi/RBM 2,590,000in lb
» 5mm inner liners available on certain applications† Dependent on wheel base and axle capacity
WHEELBASE
» Wheel bases can be adapted to suit your application - Ask your Authorised Dealer.
AFTERFRAME
» 1,510mm (59.44”) to 1,550mm (61”)» All chassis lengths come with tapered rail ends
CAB SUPPORT
» Front: Two metalastic pivot mounts» Rear: Air isolation with dual shock absorbers» Fully suspended cab» Rear panard rod
BULLBAR/ BUMPER/ FUPS
» Light weight alloy bumper with front underrun protection» Heavy duty bullbar with front underrun protection (optional)» Temporary transit FUP device (option)
OUTBACK PACK
» Heavy duty protection consisting of shields, dampers and other features adapted to severe conditions - Ask your Authorised Dealer
FUEL TANKS
» 26” round alloy tanks (standard) or steel (CA) (Refer Wheelbase Chart)
» Large capacity D-shaped tanks (optional)» Round or D-Shaped stainless steel urea tanks (125, 150 or 200ltr)» Stainless steel D tank straps (optional)» A variety of tank finishes is available - ask your Authorised Dealer
REMOTE BREATHERS
» Transmission, fuel and axle remote breather kit (optional)
CHASSIS ACCESS STEP
» Staired and perforated 2 step design (optional)
BATTERIES
» Four 12volt Bulldog batteries, high capacity (620 CCA)» LH and RH frame mounted with black battery box cover» Polished aluminium battery box cover (optional)» Batteries mounted in sleeper if applicable» Stacked battery box» Dual in-chassis frame mounted with black plastic covers
TRAILER CONNECTIONS
» Trailer connections back of cab» Trailer - connections back of cab and rear of frame (optional)» Air: Service and emergency with blanking plugs» Electrical: 12volt 7-pin female base with HD 5mm² cabling
ELECTRICAL
» Chassis harness with protective conduit
CHASSIS
WHEELBASE SPECIFICATIONS
WHEELBASE (mm) EXHAUST TO CENTRE OF DRIVE (mm)MAXIMUM FUEL CAPACITY
ADBLUE TANK CAPACITY
TURNING CIRCLE (m)
Day Cab
Super Cab
40" Sleeper
46" Sleeper
52" Sleeper
60" Sleeper
Kerb to Kerb
Bumper to Back of Cab 3115 3725 3930 4085 4235 4490
5490 3433 2823 2618 2463 2313 19.2
5800 2478 2080L 200L 20.1
5840 3783 3173 2968 2813 2663 1650L 150L 20.2
6090 4033 3423 3218 3063 2913 1950L 150L 21
6200 2878 2240L 200L 21.4
6290 4233 3623 3418 3263 3113 1950L 150L 21.6
CAB
TELEMATICS
Mack telematics system - speak with your Authorised Dealer for further information.
SHELL
» Fusion Cab, ECE29 (cab strength test) compliant» Two piece windscreen
SLEEPER OPTIONS
» 710mm (28”) Super Cab with rear cabin extension» 911mm (36”) High-rise premium sleeper - 4 door» 1,015mm (40”) Mid-rise premium sleeper – 4 door » 1,170mm (46”) Mid-rise premium sleeper – 4 door
SLEEPER OPTIONS (CONT.)
» 1,320mm (52”) Mid-rise premium sleeper – 4 door» 1,320mm (52”) High-rise premium sleeper – 4 door» 1,520mm (60”) Mid-rise premium sleeper - 3 door
All standard sleepers have 4 access doors and vertical cab extenders* Note additional sleeper options are available, speak with your Authorised Dealer.
CAB INTERIOR
» Overhead storage (up to 3 pockets based on cab configuration)» Rear Wall storage available (based on cab configuration)» Door Storage (2 pockets)» Cup Holders in dash» Centre storage console (available based on cab configuration)
COURTESY LAMPS
» Drivers/Passengers door entry lighting» Ambient floor lighting
SAFETY & WARNING
» Set of 3 safety warning triangles» Door mounted emergency procedure guide (optional)» Emergency eye wash bottle (optional)» 2.5kg in cab mounted fire extinguisher (optional)
TYRE EQUIPMENT
» Wheel lug wrench kit» Bottle jack (optional)
CAB EXTERIOR
» Fibreglass bonnet and polyfibre fenders with splash aprons» Bonnet tilts forward with spring assist» Chrome grille surround and side air intakes» Polished stainless steel cab skirts and air intake tubes» Black nylon bonnet hold down straps» Bright finish bonnet hold down straps (optional)» Stainless bug screen integrated with grille» Painted external sunvisor» Stainless steel exterior sunvisor (optional)
HEADLAMPS
» Hella integral light/indicator unit with polycarbonate lens
MARKER & TAIL LAMPS
» 5 roof-mounted amber lights and 3 in 1 tail lamp» LED roof clearance and tail lamps (optional)
REVERSING ALARM
» Chassis mounted back up alarm
WARNING BEACON
» Single amber revolving roof beacon (optional)» Double amber revolving roof beacons (optional)» Double amber revolving beacons air intake mounted (optional)
HOOK UP LAMP
» Rear of cab mounted hook up lamp (optional)
HORNS
» 2 x roof mounted, air horn trumpets» 2 x under bonnet mounted, electric
MIRRORS
» Heated ‘West Coast’ mirrors with stainless steel arms» LH and RH power mirrors» LH and RH 7" spotter mirrors» LH down mirror (optional)
WINDSCREEN STONE GUARD
» Matt black mesh windscreen stone guard (optional)
CAB INTERIOR (CONT.)
» Interior Trim - pleated ultra leather» Central locking available» Power windows available» Self cancelling signals available (optional)» Internal grab handlesSpeak with your Authorised Dealer for all options
SEATS
» Driver: ISRI ‘Big-Boy’ air-ride Premium: ‘MACK’ embossed cloth trim, LH arm rest, upper, side and lower lumbar support with oscillating base and fore/aft seat cushion adjustment
» Driver: ISRI ‘Big-Boy’ air-ride (optional): cloth trim, upper, side and lower lumbar support with fore/aft seat cushion adjustment
» Passenger: ISRI fixed cushion» Passenger: ISRI premium air ride seat with upper and lower lumbar
support, and fore/aft seat cushion adjustment (optional)
STEERING WHEEL
» Bulldog soft touch rubber grip 457mm (18”) diameter» Leather grip steering wheel (optional)» Adjustable tilt and telescopic steering column
INSTRUMENT
» Driver information display: Co-Pilot» Speedometer/odometer (electronic)» Tachometer/hourmeter (electronic)» Voltmeter, engine hours, distance, trip recording» Engine coolant temperature, fuel and AdBlue levels» Primary and secondary air pressure» Oil pressure and oil temperature
FULL GAUGE PACKAGE
» Manifold pressure, transmission temperature, exhaust temperature, brake application pressure, front and rear drive axle temperature
WINDSCREEN WIPERS
» Electronic variable-speed, intermittent wipers with washer» Reservoir mounted under bonnet
AUDIO SYSTEM
» Premium Radio/CD player including hands free» iPod connector and USB connector
COMMUNICATIONS
» GME CB radio (optional)» GME UHF radio (optional)
CLIMATE CONTROL
» HVAC integral cab air conditioner/heater» Electronic controls» Replaceable dust intrusion filter
CAB (CONT.)
ACCESSORIES
» Additional factory fitted accessories are available, speak with your Authorised Dealer for full details.
PAINT TYPE & COLOUR
» Cab/sleeper: Single non-metallic cab colour (Incredible white standard)» Chassis: Single non-metallic chassis colour (black standard)» Epoxy Mine specification primer (CA)
PAINT & ACCESSORIES
macktrucks.com.au BORN READY.
GET THE TOTAL PACKAGE.
Mack Genuine Parts are as tough as your truck. With premium materials and precision engineering, they’re built to take whatever the road can throw at them.
Mack Total Support gives you the added confidence of warranties, servicing and maintenance from the people who made your machine.
Find more about Mack Total Support at macktrucks.com.au/parts-and-services/
Contact your dealer today and ask them to arrange for a Mack Driver Development Trainer to contact you.
1300 MY MACK
Titan–09–12–2015 Australia
The information in this brochure was current at the time of publication. Mack Trucks reserves the right to make changes in specifications, equipment and design, or to discontinue models, options or extras without notice at any time. MACK and the Bulldog design are registered trademarks.
All rights reserved. V-MAC is a registered trademark. All rights reserved.