[Title will be auto-generated]

ALLIED VISION TECHNOLOGIES GMBH Taschenweg 2a | D-07646 Stadtroda | Germany Phone: +49 36428/677-0 | Fax: +49 36428/677-24

www.alliedvisiontec.com | [email protected]

AVT camera accessories 1394 drag chain cable

1394 cables for moving applications

2


1394 drag chain cables for moving applications AVT’s mechanically robust, drag chain and robot 1394 cables are ideal for moving applications. The high quality cables guarantee low damping and best signal quality for all speeds.

Specifications

Feature 1394a, robust 1394a, drag chain 1394a/b, robotics

Cycles

(not directly comparable due to different test conditions)

1,000,000

(2 return sheaves, r = 120 mm)

6,000,000

(drag chain @ radius 75 mm

stroke 600 mm accel. 10 m/s2 speed 2 m/s)

20,000,000

(Rolling flex @ radius 50 mm

stroke 1500 mm accel. 2 g = 19.62 m/s2)

Jacket Pb free PVC; 7.2 mm Ø TPE based; 7.5 mm Ø PU; 7.5 mm Ø

Outer shield Tinned annealed Cu wire, >85 % coverage

Tinned annealed Cu wire, ca. 90 % coverage

Silver plated Cu

Conductor A (data)

Tinned copper, 30 x 0.08 (AWG26); 0.405 mm

Tinned copper, AWG 26

Silver plated copper, AWG 28

Conductor B (power)

Tinned copper, 105 x 0.08 (AWG20); 0.813 mm

Bare copper, AWG 22

Bare copper, AWG 22

Max. DC resistance

38.3 Ω/km at 20 °C (Conductor B)

264 Ω/km (conductor A) 116 Ω/km (conductor B)

202 Ω/km (conductor A) 64 Ω/km (conductor B)

Char. Impedance

110 Ω ± 6% n/a 110 Ω ± 5%

Attenuation 0.3 dB/m @ 100 MHz 0.4 dB/m @ 200 MHz 0.6 dB/m @ 400 MHz 1.0 dB/m @ 1000 MHz

n/a 0.3 dB/m @ 100 MHz 0.4 dB/m @ 200 MHz 0.6 dB/m @ 400 MHz 1.0 dB/m @ 800 MHz 1.2 dB/m @ 1000 MHz

Time delay Max. 5.05 ns/m n/a 4.3 ns/m

Skew delay Max. 400 ps/m between pairs

n/a < 25 ps/m

Compliance UL 20276 (80 ºC, 30 V), ROHS

ROHS, CE, UL, DESINA ROHS, CE, UL

3


Pinout

IEEE 1394a

Connectors are viewed as looking at the front plug face.

*Twisted pair shields are only connected by using cable material according to IEEE Std 1394TM -1995.

If cable material according to IEEE Std 1394b™ -2002 is used, twisted pair shields are not connected inside the cable.

Plug 1 Signal name at plug 1 Plug 2

1 VP (Power Voltage) 1

2 VG (Power Ground) 2

3 TPB* (Twisted Pair B minus) 5

4 TPB (Twisted Pair B plus) 6

5 TPA* (Twisted Pair A minus) 3

6 TPA (Twisted Pair A plus) 4

Plug shield Cable outer shield Plug shield

plug shield

1

2

3

4

5

6

1

2

5

6

3

4

P1 P2PINOUT

plug shield plug shield

1

2

3

4

5

6

4


IEEE 1394b


Plug 1 Signal @ plug 1 Plug 2





5 TPA (R) (Twisted Pair A ground reference)

9

6 VG (Power ground) 6

7 No connection 7


9 TPB (R) (Twisted Pair B ground reference)

5


P1 P2PINOUT

8912

3456

8534

1296

4 3 2 15 6 7 8 9

plug shield plug shield plug shield

5


Order codes

Description Length Order number

Cable 1394a, latch - latch, robust 1.0 m 2.0 m 3.0 m 4.5 m

K1200187 K1200189 K1200190 K1200166

Cable 1394a, latch - latch, drag chain 4.5 m 6.0 m 10.0 m

K1200200 K7200039 K7200038

Cable 1394b, screw lock - screw lock, robot 5.0 m K1200205

Other cable lengths are available on request.

Description Cable diameter Order number

Ferrite for AVT cables 3.5 – 5.0 mm 4.5 – 6.0 mm 6.0 – 7.5 mm

K8420055 K8420057 K8420056

Ferrite removing tool For all sizes K8420058

Disclaimer Technical specifications are subject to change without notice. All trademarks are acknowledged as property of their respective owners. Copyright © 2012 Allied Vision Technologies. Document owner: OGU

ALLIED VISION TECHNOLOGIES GMBH Taschenweg 2a D-07646 Stadtroda / Germany All rights reserved. Managing Director: Mr. Frank Grube Tax ID: DE 184383113

AVT 1394 accessories 1394a cable clip

1394a cable clip

Your solution to improve 1394a wiring

AVT’s 1394a cable clip locks AVT’s 1394a standard cable to your AVT Guppy cameras and 1394a accessories. This clip may be added to existing 1394a cabling to secure the plug connection against accidental extraction.

Highlights

Improving 1394a wiring Compatible with AVT's Guppy camera May be added to existing cabling

ALLIED VISION TECHNOLOGIES GMBH Design and specification of the described product(s) Taschenweg 2a | D-07646 Stadtroda | Germany are subject to change without notice. Phone: +49 36428/677-0 | Fax: +49 36428/677-24 www.alliedvisiontec.com | [email protected] © 04/2008

AVT 1394 accessories 1394a cable

Application examples

Clip used on camera side Clip used on card side

Compliance list

Order numbers Description Camera Guppy-series Compliant to all cameras of the Guppy series Active Accessories K0000344 FWX2-PCIE10-2 (Dual OHCI FireWire (2x IEEE 1394a) to PCI Express Host Adapters) K0000345 FWX2-PCIE10-4 (Dual OHCI FireWire (4x IEEE 1394a) to PCI Express Host Adapters) K0000360 FW-PCIE02 (2-port IEEE 1394 to PCI Express Host Adapter) K0000206 IOI-4601-21 (2-port Dual Channel OHCI Compliant IEEE 1394 to PCI Host Adapter) K0000207 IOI-4601-22 (4-port Dual Channel OHCI Compliant IEEE 1394 to PCI Host Adapter) K0000361 FW-PCI3201 (3-port OHCI Compliant 1394a to PCI Host Adapter) K0000369 IOI-1394R-A2 (2-port 1394a Repeater, clamp locking) K0000204 IOI-1394R3B (IEEE-1394a 3-port Repeater) K0000334 FW2UTP-02B (Converter 1x1394a to 2x Cat5) K0000370 FW-UTPS400 (Converter 2x1394a to 1x Cat5) Cable K1200071 IEEE 1394a; cable 6 pin – 6 pin, 0.5 m K1200226 IEEE 1394a; cable 6 pin – 6 pin, 1.0 m K1200063 IEEE 1394a; cable 6 pin – 6 pin, 2.0 m K1200078 IEEE 1394a; cable 6 pin – 6 pin, 3.0 m K1200150 IEEE 1394a; cable 6 pin – 6 pin, 4.5 m K1200158 IEEE 1394a; cable 6 pin – 6 pin, 6.0 m K1200157 IEEE 1394a; cable 6 pin – 6 pin, 8.0 m K1200161 IEEE 1394a; cable 6 pin – 6 pin, 10.0 m and other length based on this cable

Ordering numbers: 1394a cable clips 10 pcs K0000371 1394a cable clips 50 pcs K0000372

ALLIED VISION TECHNOLOGIES GMBH Design and specification of the described product(s) Taschenweg 2a | D-07646 Stadtroda | Germany are subject to change without notice. Phone: +49 36428/677-0 | Fax: +49 36428/677-24 v 1.0

www.alliedvisiontec.com | [email protected] © 04/2008

AVT 1394 accessories 1394 i.LINKTM adapter

i.LINKTM adapter for laptop application

Your cable for laptop applications with AVT IEEE 1394 cameras.

ALYSIUMs i.LINKTM cable is ideal for connection of IEEE 1394 cameras to any laptop with 4-pin i.LINKTM connector. The high quality cables guarantee low damping and best signal quality for all speeds. Due to the power connector you can provide bus power and do not have to power each single camera.

Highlights

Compliant with IEEE 1394a RoHS compliant Compatible with AVT’s IEEE 1394 cameras

ALLIED VISION TECHNOLOGIES GMBH Taschenweg 2a | D-07646 Stadtroda | Germany Phone: +49 36428/677-0 | Fax: +49 36428/677-24 www.alliedvisiontec.com | [email protected]

AVT 1394 accessories 1394 i.LINKTM adapter

Technical Specifications

Feature Description 1394 cable Description power cable Jacket Pb free PVC; 0.38 mm thick,

4.8 mm Ø Pb free PVC; 0.53 mm thick, 4.0 mm Ø

Outer shield - Braid - aluminium wire, min. 90 % coverage - Al-foil/mylar, 25 % overlap

Spiral Tinned copper, min. 93 % coverage

Cable assembly 2 pairs of (A) plus 2x Filler (no power conductor)

Coaxial cable

Inner shield - Spiral - tinned copper, min. 95 % coverage - Al-foil/mylar, 25 % overlap

Insulation A FOAM-SKIN-PE; 0.27 mm thick; 0.84 mm Ø

FOAM-PE; 1.075 mm thick; 2.75 mm Ø

Conductor A (Data) Tinned copper, 7x 0.102 (AWG38); 0.255 mm

Conductor B (Power) Tinned copper, 7x 0.203 (AWG32); 0.511 mm

Max. DC resistance 376 Ω/km at 20°C 93.2 Ω/km at 20°C Char. impedance 110 Ω ± 6 Ω Attenuation 400 MHz: ± 1.29 dB/m Time delay Max. 5.05 ns/m Skew delay Max. 400 ps/m between pairs Compliance UL 20276 (80ºC, 30 V) UL 1354 (80ºC, 30 V)

Ordering number:

i.LINKTM adapter 4-pin – 6-pin + DC IEEE1394 Adapter 4-pin connector to 6-pin female with DC-in K1200070

Power supply 12 V DC, 1.25 A Wall power supply 15 W, circular plug-in connector 5.5/2.1 mm E3100012 Ferrite for AVT cables for cable diameter 3.5 --- 5.0 mm K8420055 Tool for ferrites for all sizes, to remove ferrites from cable K8420058

Note: Please be aware of polarity of the used power supply ( ). Wrong polarity can damage camera or laptop.

ALLIED VISION TECHNOLOGIES GMBH Design and specification of the described product(s) Taschenweg 2a | D-07646 Stadtroda | Germany are subject to change without notice. Phone: +49 36428/677-0 | Fax: +49 36428/677-24 Author: GBR www.alliedvisiontec.com | [email protected] © 10/2007

AVT 1394 accessories 1394 cable

1394b high grade cable

Your high grade / long distance cables for AVT IEEE 1394b cameras.

ALYSIUMs high grade cables are ideal for connection of IEEE 1394b cameras in any industrial application. The high quality cables guarantee low damping and best signal quality for all speeds. Both sides are equipped with screw lock connectors. The maximum length ist extended up to 15 meters due the excellent electrical characteristics of the cable.

Highlights

Compliant with IEEE 1394b UL certified and RoHS compliant Compatible with all AVT’s IEEE 1394b cameras Extended Lenghts up to 15 meters


AVT 1394 accessories 1394 cable


Feature Description Jacket Pb free PVC; 0.81mm thick, 11,9 mm Ø; UL 20276 cert. (@ 80 ºC, 30 V) Outer braid shield Tinned annealed Cu, min. 85 % coverage, composition 0,12mm Binder tape Paper Cable assembly S, 2x (A) plus 2x (B) Inner shield AL-PET (min 100%) Insulation A XLFMPE; 0.66 mm thick; 2,10 mm Ø Conductor A (Data) Tinned annealed Cu; 7 x 0.26 (AWG22); 0.78 mm Ø Conductor B (Power) Tinned annealed Cu; 26 x 0.16 (AWG20); 0.94 mm Ø Insulation B HR-LF-PVC; 0.41 mm thick; 1,76 mm Ø Max. DC resistance A:56,9 B:39,1 [Ohm/km at 20 °C ] Char. Impedance 110 Ohm nominal Static bending radius min. 6 x outer diameter [~72 mm)

Pinout IEEE 1394b


P1 P2PINOUT

8912

3456

8534

1296

4 3 2 15 6 7 8 9


Plug 1 Signal name at plug 1 end Plug 2 1 TPB* (Twisted Pair B minus) 3 2 TPB (Twisted Pair B plus) 4 3 TPA* (Twisted Pair A minus) 1 4 TPA (Twisted Pair A plus) 2 5 TPA (R) (Twisted Pair A ground reference) 9 6 VG (Power Ground) 6 7 No connection 7 8 VP (Power Voltage) 8 9 TPB (R) (Twisted Pair B ground reference) 5 Plug shield Cable outer shield Plug shield

Ordering number:

9-Pin --- 9-Pin industrial 15,0m IEEE 1394b; 2x screw lock, high grade long distance, for Pike/ Stingray K1200291 Shorter lengths on request!

ALLIED VISION TECHNOLOGIES GMBH Design and specification of the described product(s) Taschenweg 2a | D-07646 Stadtroda | Germany are subject to change without notice. Phone: +49 36428/677-0 | Fax: +49 36428/677-24 www.alliedvisiontec.com | [email protected] © 02/2009


1394 1394a standard cable

Your standard cable for AVT IEEE 1394a cameras.

Alysium’s standard cable is ideal for connection of AVT’s IEEE 1394a cameras to any IEEE 1394a port in a PC. Due to its great price-performance ratio it is suitable for all standard applications. It comes with each AVT Guppy, Marlin and Oscar camera for easy plug and play.

Highlights

Compliant with IEEE 1394a UL 20276 certified and RoHS compliant Pb free PVC jacket Compatible with AVT’s IEEE 1394a cameras


http://dict.tu-chemnitz.de/dings.cgi?o=3021;service=deen;iservice=en-de;query=price-performance

http://dict.tu-chemnitz.de/dings.cgi?o=3021;service=deen;iservice=en-de;query=ratio



Lenght

Ordering number: Cable 0.5 m 6-pin to 6-pin IEEE1394a, standard K1200071 Cable 1.0 m 6-pin to 6-pin IEEE1394a, standard K1200226 Cable 2.0 m 6-pin to 6-pin IEEE1394a, standard K1200063 Cable 3.0 m 6-pin to 6-pin IEEE1394a, standard K1200078 Cable 4.5 m 6-pin to 6-pin IEEE1394a, standard K1200150 Cable 6.0 m 6-pin to 6-pin IEEE1394a, standard K1200158 Cable 8.0 m 6-pin to 6-pin IEEE1394a, standard K1200157 Cable 10.0 m 6-pin to 6-pin IEEE1394a, standard K1200161

Feature DescriptionJacket Pb free PVC; 0.83 mm thick, 5.5 mm Ø Outer braid shield Aluminium wire, min. 90 % coverage Outer shield Al-foil / mylar, 25 % overlap Cable assembly 2 pairs of (A) plus 2 x (B) Inner braid shield Tinned copper, min. 75 % coverage Inner shield Al-foil / mylar, 25 % overlap Insulation A FOAM-SKIN-PE; 0.27 mm thick; 0.84 mm Ø Conductor A (Data) Tinned copper, 7 x 0.102 (AWG38); 0.255 mm Conductor B (Power) Tinned copper, 7 x 0.203 (AWG32); 0.511 mm Insulation B SR-PVC; 0.24 mm thick; 1.07 mm Ø Max. DC resistance 93.2 Ω/km at 20°C Char. impedance 110 Ω ± 6 Ω Attenuation 400 MHz: ± 1.29 dB/m Time delay Max. 5.05 ns/m Skew delay Max. 400 ps/m between pairs Compliance UL 20276 (80ºC, 30 V)

ALLIED VISION TECHNOLOGIES GMBH Design and specification of the described product(s) Taschenweg 2a | D-07646 Stadtroda | Germany are subject to change without notice. Phone: +49 36428/677-0 | Fax: +49 36428/677-24 Author: NBR www.alliedvisiontec.com | [email protected] © 10/2008

AVT camera accessories 1394 locking cables

ALLIED VISION TECHNOLOGIES GMBHTaschenweg 2a | D-07646 Stadtroda | GermanyPhone: +49 36428/677-0 | Fax: +49 36428/677-24www.alliedvisiontec.com | [email protected]

1394 locking cables

Your locking cables for AVT IEEE 1394 cameras

AVT locking cables are ideal for connection of IEEE 1394 cameras in any industrial application. The high quality cables guarantee low damping and best signal quality for all speeds. Due to the 3 combinations all kinds of AVT cameras can be combined with all kinds of IEEE 1394 interfaces under different conditions.

Highlights• Compliant with IEEE 1394a and IEEE

1394b• RoHS compliant• Compatible with all AVT's IEEE 1394

cameras

[email protected]


AVT I/O cables are manufactured in accordance with the CE standard and its underlying directions.

AVT I/O cables comply with the requirements of the EU directive 2002/95/EC (Restriction of the use of certain hazardous substances in Electrical and Elec-tronic Equipment - RoHS).

We declare, under our sole responsibility, that the described 1394 locking cables conform to the directives of UL20276.

2


Technical specifications

Feature Description

Jacket Pb free PVC; 0.6 mm thick, 7.1 mm Ø; UL 20276 cert. (@ 80 ºC, 30 V)Outer braid shield Tinned annealed Cu, min. 85 % coverageOuter shield AL-PET tapeCable assembly 2x (A) plus 2x (B)Inner shield AL-PETDrain wire A Tinned annealed Cu; 7x 0.203 (AWG24); 0.61 mm ØInsulation A FM-PE; 0.5 mm thick; 1.6 mm ØConductor A (Data) Tinned annealed Cu; 7x 0.203 (AWG24); 0.61 mm ØConductor B (Power) Tinned annealed Cu; 7x 0.203 (AWG24); 0.61 mm ØInsulation B HR-LF-PVC; 0.15 mm thick; 0.91 mm ØMax. DC resistance 88 Ohm/km at 20 °CChar. impedance 110 Ohm +/-6Attenuation 400 MHz: <= 0.4 dB/mTime delay Max. 5.05 ns/mSkew delay Max. 50 ps/m between pairs

Table 1: 1394 locking cables specifications

3


Pinout

IEEE 1394 legacy (9-pin to 6-pin)


Figure 1: Pinout: IEEE 1394 legacy (9-pin to 6-pin)

Note

Twisted pair shields are only connected by using cable material according to IEEE Std 1394TM -1995.

If cable material according to IEEE Std 1394bTM -2002 is used, twisted pair shields are not connected inside the cable.

Plug 1 Signal name at plug 2 end Plug 2

5 TPB* (Twisted Pair B minus) 16 TPB (Twisted Pair B plus) 23 TPA* (Twisted Pair A minus) 34 TPA (Twisted Pair A plus) 42 TPA (R) (Twisted Pair A ground reference) 52 VG (Power Ground) 6

No connection 71 VP (Power Voltage) 82 TPB (R) (Twisted Pair B ground reference) 9Plug shield Cable outer shield Plug shield

Table 2: Connectors layout

4


IEEE 1394a


Figure 2: Pinout: IEEE 1394a


1 VP (Power Voltage) 12 VG (Power Ground) 23 TPB* (Twisted Pair B minus) 54 TPB (Twisted Pair B plus) 65 TPA* (Twisted Pair A minus) 36 TPA (Twisted Pair A plus) 4Plug shield Cable outer shield Plug shield

5


IEEE 1394b


Figure 3: Pinout: IEEE 1394b


1 TPB* (Twisted Pair B minus) 32 TPB (Twisted Pair B plus) 43 TPA* (Twisted Pair A minus) 14 TPA (Twisted Pair A plus) 25 TPA (R) (Twisted Pair A ground reference) 96 VG (Power Ground) 67 No connection 78 VP (Power Voltage) 89 TPB (R) (Twisted Pair B ground reference) 5Plug shield Cable outer shield Plug shield

6


r code

064

163

165

162

167

091

160

212

159

r code

198

211

171

210

209

r code

306

112

330

307

169

308

333

Order codes

1394a cables Description Orde

FireWire cable -2x Interlock IEEE 1394a; 2x Interlock, 4.5 m with Ferrites, for Marlin/Oscar/Guppy K1200

FireWire cable -2x Interlock IEEE 1394a; 2x Interlock, 10 m with Ferrites, for Marlin/Oscar/Guppy K1200



FireWire cable -1x Interlock IEEE 1394a; (1x Interlock) 3.0 m, for Marlin/Oscar/Guppy K1200




FireWire cable -1x Interlock IEEE 1394a; (1x Interlock) 10 m, for Marlin/Oscar/Guppy K1200

1394 legacy cables Description Orde

Cable 0.5 m 9-pin to 6-pin industrial IEEE 1394b/a; 9 pin (screw lock)/6 pin (latch), 0.5 m K1200




Cable 10 m 9-pin to 6-pin industrial IEEE 1394b/a; 9 pin (screw lock)/6 pin (latch), 10 m K1200

1394b cables straightwithout ferrite

Description Orde

Cable 0.5 m 9-pin to 9-pin, industrial IEEE 1394b; 2x screw lock, 0.5m, black, without ferrite K1200





Cable 7.5 m 9-pin to 9-pin, industrial IEEE 1394b; 2x screw lock, 7.5m, black, long distance, without ferrite K1200

Cable 10.0 m 9-pin to 9-pin, industrial IEEE 1394b; 2x screw lock, 10 m, black, long distance, without ferrite K1200

7


r code

297

298

295

296

299

300

de

Angled cables (cable exit direction at view on camera back):

= angle left, = angle up, = angle right, = angle down

Other lengths on request.

Additional referencesTo download AVT Technical Manuals etc.:http://www.alliedvisiontec.com/emea/support/downloads/product-literature.html

AVT product page:http://www.alliedvisiontec.com/emea/products/cameras.html

AVT knowledge base:http://www.alliedvisiontec.com/emea/support/knowledge-base.html

AVT case studies:http://www.alliedvisiontec.com/emea/products/applications.html

1394b cables angled Description Orde

Cable 3.0 m 9-pin to 9-pin angled IEEE1394b; angled on one side, 2x screw lock, 3.0 m Pike, Stingray,Guppy PRO

K1200


K1200


K1200


K1200


K1200


K1200

Figure 4: IEEE 1394b angled connector (left and right version have the same dimensions)

Ferrites Description Order co

Ferrite for AVT cables for cable diameter 3.5 - 5.0 mm K8420055



Tool for ferrites for all sizes, to remove ferrites from cable K8420058

8

http://www.alliedvisiontec.com/emea/support/downloads/product-literature.html

http://www.alliedvisiontec.com/emea/products/cameras.html

http://www.alliedvisiontec.com/emea/support/knowledge-base.html

http://www.alliedvisiontec.com/emea/products/applications.html


CopyrightAll text, pictures and graphics are protected by copyright and other laws cover-ing intellectual property. It is prohibited to copy or modify them for trade use or transfer, or inclusion on web sites.

Allied Vision Technologies GmbH 03.07.12

Headquarters:

ALLIED VISION TECHNOLOGIES GMBHTaschenweg 2aD-07646 Stadtroda / GermanyAll rights reserved.Managing Director:Mr. Frank GrubeTax ID: DE 184383113

Design and specification of the described product(s) are subject to change without notice.

Document owner: TFR

07/12

9

ALLIED VISION TECHNOLOGIES GMBH Taschenweg 2a | D-07646 Stadtroda | Germany Phone: +49 36428/677-0 | Fax: +49 36428/677-24

www.alliedvisiontec.com | [email protected]

AVT camera accessories 1394 legacy cables

1394 legacy cables

2


Legacy cables for IEEE 1394 cameras AVT´s legacy cables are ideal for connection of IEEE 1394 cameras to any IEEE 1394a or IEEE 1394b port of a PC or laptop. The high quality cables guarantee low damping and best signal quality for all speeds.

Specifications All cables comply with IEEE 1394 standard (IEEE Std 1394™-1995)

Feature Description

Char. Impedance 110 Ohm +/-6

Attenuation (400 MHz) ≤ 1.28 dB/m

Time delay Max. 5.05 ns/m

Skew delay Max. 400 ps

3


Pinout

IEEE 1394a legacy (9-pin to 6-pin)

*Twisted pair shields are only connected by using cable material according to IEEE Std 1394TM -1995.

If cable material according to IEEE Std 1394b™ -2002 is used, twisted pair shields are not connected inside the cable.







2 TPA (R) (Twisted Pair A ground reference)

5

2 VG (Power Ground) 6

No connection 7


2 TPB (R) (Twisted Pair B ground reference)

9


P1 P2PINOUT

1

34

56

2

8534

1296

4 3 2 1

5 6 7 8 9

plug shield

1

2

3

4

5

6


*

4


IEEE 1394 (6-pin to 4-pin)



VP (Power Voltage) 1

Plug shield VG (Power Ground) 2





Cable outer shield Plug shield

1

2

3

4

5

61

2

3

4

2

5

6

3

4

P1 P2PINOUT

1234

plug shield

plug shield

plug shieldplug shield

5


IEEE 1394 legacy (9-pin to 4-pin)


Plug 1 Signal at plug 2 Plug 2





Plug shield TPA (R) (Twisted Pair A ground reference)

5

VG (Power Ground) 6

No connection 7

VP (Power Voltage) 8

Plug shield TPB (R) (Twisted Pair B ground reference)

9

Cable outer shield Plug shield

12344 3 2 15 6 7 8 9

1

2

3

4

534

12

P1 P2PINOUT

9plug shield

plug shield

plug shield

plug shield

6


Order codes

Description Length Order number

Legacy cable 1394b (9 pin) to 1394a (4 pin) standard connectors 4.5 m K1200126

Legacy cable 1394a (6 pin) to 1394a (4 pin) standard connectors 2.0 m 4.5 m

K1200056 K1200055

Legacy cable 1394a (6 pin latch) to 1394b (9 pin screw lock) connectors 0.5 m 3.0 m 4.5 m 7.5 m 10 m

K1200198 K1200211 K1200171 K1200210 K1200209

Other cable lengths are available on request.

Description Cable diameter Order number

Ferrite for AVT cables 3.5 – 5.0 mm 4.5 – 6.0 mm 6.0 – 7.5 mm

K8420055 K8420057 K8420056

Ferrite removing tool For all sizes K8420058

Disclaimer Technical specifications are subject to change without notice. All trademarks are acknowledged as property of their respective owners. Copyright © 2012 Allied Vision Technologies. Document owner: OGU

ALLIED VISION TECHNOLOGIES GMBH Taschenweg 2a D-07646 Stadtroda / Germany All rights reserved. Managing Director: Mr. Frank Grube Tax ID: DE 184383113

V2.0.2 22 June 2012

Instruction Leaflet AVT I/O cables

AVT I/O cables are manufactured in accordance with the CE standard and its underlying directions.

AVT I/O cables comply with the requirements of the EU directive directive 2002/95/EC (Restriction of the use of certain hazardous substances in Electrical and Electronic Equipment - RoHS).

We declare, under our sole responsibility, that the described AVT I/O Cables conform to the directives of UL20276.

Contacting AVTOrdering and general information:[email protected] (for Germany): +49 (0)36428 677-230phone (for North America): +1 978-225-2030phone (for Singapore): +65 6634-9027

Support:[email protected] Germany/North America:Please check the link for your local dealer.http://www.alliedvisiontec.com/emea/sales/sales-locations.html

Specifications

Feature 8-pin cable 12-pin cable13-pin cableManta / Stingray board level

Jacket HR-PVC (Pb free), 0.81 mm thick, 5.0 mm Ø

PVC Class 43, 6.4 mm Ø +/-0.20

PVC 105 °C, 6.4 mm Ø

Outer braid shield

Tinned annealed copper, min. 85 % coverage

Tinned annealed copper, min. 85 % coverage

Tinned annealed copper

Cableassembly

5 pairs (4 used) 12 x single 13 x single

Insulation HRLF PVC 0.1 mm thick, 0.58 mm Ø

SR-PVC PVC 80 °C

Conductor Tinned annealed copper 7 x 0.127 (AWG 28); 0.38 mm Ø

Tinned annealed copper,7 x 0.16 mm(AWG26)

Tinned annealed copper, 7 x 0.16 (AWG26); 0.48mm Ø

Max.conductor DC resistance

246 /km at 20°C

max. 140 /km at +20°C

max. 155 /km at +20°C

Min.insulation DCresistance

10 M x km at 20°C

min. 100 M x km at +20°C

min. 153 M x km at +20°C

Compliance UL 20276 (80ºC / 30 V), RoHS (2002/95/EC)

UL/cUL , Style 2464/1061 , RoHS

UL 2464/1061, VDE881, UL1061

Trigger cable configuration

AVT partnumber

LegacyAVT part number

Description

2814 K1200191 12-pin HIROSE female to open end, 2.0 m2815 K1200292

02-6033A02-6031A

12-pin HIROSE female to open end, 3.0 m

2817 K1200193 12-pin HIROSE female to open end, 5.0 m2818 K1200194 12-pin HIROSE female to open end, 10.0 m2789 02-6032A 12-pin HIROSE male to open end, 3.0 m2790 - 12-pin HIROSE male to open end, 5.0 m2791 - 12-pin HIROSE male to open end, 10.0 m

K1200301 - 13-pin PicoBlade to open end, 3.0mK1200302 - 13-pin PicoBlade to open end, 5.0mK1200196 - 8-pin HIROSE female to open end, 2.0 mK1200197 - 8-pin HIROSE female to open end, 5.0 mK1200229 - 8-pin HIROSE female to open end, 10.0 m

2792 02-6041A 14-pin Mini-D shell to open end, 3.0 m2793 - 14-pin Mini-D shell to open end, 5.0 m2794 - 14-pin Mini-D shell to open end, 10.0 m

Trigger cable (only connected to Trigger IN 1)K1200267 - 12-pin HIROSE female to BNC, 2.0 mK1200252 - 12-pin HIROSE female to BNC, 5.0 mK1200240 - 12-pin HIROSE female to open end, 2.0 m K1200244 - 12-pin HIROSE female to open end, 10.0 m

I/O connector pin assignment

AVT standard HIROSE 12-pin connector

Supported AVT cameras: 1394a: Marlin, Oscar

1394b: Stingray, Guppy PRO, Pike

GigE: Manta, Manta PoE, Prosilica GT / GX / GC

Drawing Pin Color1 Blue2 Red3 Pink4 Grey5 Yellow6 Green7 Brown8 White9 Black

10 Orange11 White/Black12 White/Brown

11029

8

7

6

12113

45

HR10A-10P-12S

http://www.alliedvisiontec.com/emea/sales/sales-locations.html

AVT Guppy HIROSE 8-pin connector

Prosilica GE HIROSE 12-pin female connector

Drawing Pin Color1 Yellow dot Red2 Yellow dot Black3 Grey dot Red4 Grey dot Black5 Pink dot Black6 Pink dot Red7 Orange dot Black8 Orange dot Red

Drawing Pin Color1 Blue2 Red3 Pink4 Grey5 Yellow6 Green7 Brown8 White9 Black

10 Orange11 White/Black12 White/Brown

HR25A-7TP-8S

7 4

1

2

368

5

Supported AVT cameras: 1394a: Guppy

91081

2

3

4

11127

65

HR10A-10P-12P

Supported AVT cameras:GigE: Prosilica GE

AVT Manta / Stingray board level camera Picoblade connector

Drawing Pin Color1 Blue2 Red3 White/Black4 Grey5 Yellow6 Green7 Brown8 White9 Black

10 Orange11 White/Brown12 Violet13 Shield-Transparent

1

13

Supported AVT cameras:Manta/Stingray board level

Prosilica GB/GS camera connector

Note

Drawing Pin Color1 Red2 Black3 White4 Brown5 Green6 Blue7 Orange8 ---9 ---

10 Yellow11 White/Brown12 Pink13 White/Black14 Grey

For technical details of input ranges Uin, see the AVT Technical Manuals and the AVT I/O cable data sheet.

14-pin Mini-D

17

14 8

Supported AVT cameras:Prosilica GB/GS series

Additional referencesTo download AVT Technical Manuals etc.:http://www.alliedvisiontec.com/emea/support/downloads/product-literature.htmlAVT product page:http://www.alliedvisiontec.com/emea/products/cameras.htmlAVT knowledge base:http://www.alliedvisiontec.com/emea/support/knowledge-base.htmlAVT case studies:http://www.alliedvisiontec.com/emea/products/applications.html

CopyrightAll text, pictures and graphics are protected by copyright and other laws covering intellectual property. It is pro-hibited to copy or modify them for trade use or transfer, or inclusion on web sites.Allied Vision Technologies GmbH 06/2012Headquarters:Allied Vision Technologies GmbHTaschenweg 2aD-07646 Stadtroda / GermanyAll rights reserved.Managing Director:Mr. Frank GrubeTax ID: DE 184383113

http://www.alliedvisiontec.com/emea/support/downloads/product-literature.html

http://www.alliedvisiontec.com/emea/products/cameras.html

http://www.alliedvisiontec.com/emea/support/knowledge-base.html

http://www.alliedvisiontec.com/emea/products/applications.html

Date post:	19-Mar-2016
Category:	Documents
Upload:	emi-eguchi
View:	223 times
Download:	8 times

[Title will be auto-generated]

Documents