Date post: | 04-Jun-2018 |
Category: |
Documents |
Upload: | kodhamagulla-sudheer |
View: | 225 times |
Download: | 2 times |
of 25
8/13/2019 TN Configuration 2
1/25
1. Internet Explorer 6.0 with JVM plug-in is installed on your Laptop.
2. In the Internet Options, there should not be any proxy server defined in
LAN settings. Remove all such entries.
3. Make sure that the IP address of your laptop is defined as follows:
10.0.0.2 with Sub Net mask 255.255.255.0
4. A Ethernet Cross-Cable should be available.
5. Mini-Link Serial cable should be available
6. MSM 6.3 or a later version is installed on your laptop.
7. IP Addressing plan is available for that Network.
8. Mini-Link TN Id Addressing plan is also available.
Pre-requisites for Configuring a Traffic Node
8/13/2019 TN Configuration 2
2/25
- The NPU card should be installed on the slot-7 only. This is mandatory-The MMU can be installed on any of the remaining slots.
- If you are planning to have a 1+1 protected hop make sure that you have installed the
SMU2 and MMU2 cards as shown above. No other configuration is possible for 1+1.
Hardware Layout for AMM-6P
8/13/2019 TN Configuration 2
3/25
Initial Commissioning for Traffic Node
1. Insert all the Cards in the Traffic Node magazine.
2. Check the DC connector and verify that you are getting appropriate voltage
with correct polarity.
3. Power-ON the system .
4. During system start-up all the 3 LED on NPU card will glow.
5. When all the 3LEDs are lit on the NPU card , press the BR button on
the NPU card once.
6. After 30-60 seconds you will see that the Orange LED on NPU card starts
blinking, and the Green LED is continuously ON.
7. Now connect your laptop to the NPU card Ethernet Connector with a
cross- Ethernet cable.
8. Open a Internet Explorer Browser and enter the following IP address in its
address bar : 10.0.0.1 ; press Enter.
9. The page will start loading and you will see the Traffic node setup
8/13/2019 TN Configuration 2
4/25
If you see this page, it means that you have entered the
Node Installation Mode !!!
Click the Manual Configuration link on this page.
8/13/2019 TN Configuration 2
5/25
Click the Perform Software Upgrade link .
8/13/2019 TN Configuration 2
6/25
Not required to do any thing here, unless you want to do a software
upgrade. Just press the Next link.
8/13/2019 TN Configuration 2
7/25
Click the Configure Basic Security link !!! It will allow you to
setup passwords for the default users that are available. Do not
make any changes, simply click Next in the subsequent page
that appears.
8/13/2019 TN Configuration 2
8/25
Click the Configure DCN link !
8/13/2019 TN Configuration 2
9/25
I.P.add + subnet Mask should be unique for each node
OSPF Enable & OSPF Area Idshould be entered as required
Give a unique Name for the Node.
8/13/2019 TN Configuration 2
10/25
This page is an example of what values you should input .
Never Forget to click Apply after you
input all the values. Select Advanced
Configuration after that .
8/13/2019 TN Configuration 2
11/25
Enter the current Date & Time here
Click Apply & then Next
SNMP managerinfo can be set here if
you have the details.
8/13/2019 TN Configuration 2
12/25
Click this link
8/13/2019 TN Configuration 2
13/25
Do not do any changes, just press Next.
8/13/2019 TN Configuration 2
14/25
Click finish Installation to complete the
Initial installation setup.
8/13/2019 TN Configuration 2
15/25
Once you click Apply the changeswill take effect, and Node will restart
8/13/2019 TN Configuration 2
16/25
This page has important information. Please read it carefully, and note down
theIP address that appears on the above comment. You will be required to
change the IP address of your Laptop after you read this page. Make sure that
the IP address that you have entered during the Installation Mode is the same
as displayed on this page. You will need it, to gain access to this node again.
8/13/2019 TN Configuration 2
17/25
Close the I.E browser and open it again, after you have set the new IP address on your
laptop. Enter the new IP address in the address bar. You will get a login prompt.
Enter User id: control_userand Passwd: ericsson This will display the current page with
a AMM Setup. Make sure that you see all the Cards that are inserted in the Magazine.
8/13/2019 TN Configuration 2
18/25
Once you Log-in to the system , you will come to this Home Page,
where you can see the Magazine Layout.
8/13/2019 TN Configuration 2
19/25
Once you are at this screen, it is advisable to connect to the MMU with RS-232
cable and do the commissioning for the MMU and RAU. For this you will have
to launch the MSM 6.3 application. Configure the Hop as you would do for a
normal ML-E Hop.
Perform this activity for all the MMU in that Magazine.
* Traffic Routing should be strictly done after this activity only !!!!
8/13/2019 TN Configuration 2
20/25
For Traffic Routing press the Configuration Tab on the menu-bar
8/13/2019 TN Configuration 2
21/25
Once you log-in you will come to the
In the Configuration Window , select the Traffic Routingtab
8/13/2019 TN Configuration 2
22/25
8/13/2019 TN Configuration 2
23/25
Here u will see the available free E1s
on each card. Select one E1 on each
axis to create a connection between
them. Press Create . You will be
prompted to enter a Name for theCross-connection that you have done.
Repeat this process for each connection
that you need to do.
Once the connections are made
you will see them here
R b ll th ti t E1 l l l
8/13/2019 TN Configuration 2
24/25
Remember, all the cross-connections are atE1 level only
1. Connections to NPU card are to be done only when you want to extract
the traffic out of the Traffic node and terminate somewhere else.OR if you want to input Traffic to any MMU.
2. When you want to make a traffic through from one direction to other,
the connections are to be made directly between two MMUs, and not
via the NPU card.
3. When you select the cards for making cross-connections the naming
nomenclature is MMU2 4-34 1/2 ; which implies it is MMU card in
Traffic Node Magazine :1 and it is located onslot-2.
4. NPU card should always be installed onslot-7. So you will see the label
for NPU as NPU 8x2 1/7in the Traffic Routing window.
5. Depending on the Traffic Capacity of the MMU, you will see theNumber of free E1s available for cross-connections in Interface List
View window, for that specific card NPU /MMU .
1 E1 naming convention is E1 1/2/1 1 1 2
8/13/2019 TN Configuration 2
25/25
1. E1 naming convention is E1 1/2/1 1.1.2
which implies, E1 of 1st magazine, card on slot-2 , baseband-1 of that
card and 1.1.2 is the E1 number, which is 2nd
E1 of that band.E.g. E1 1/3/1 1.4.4 implies, magazine 1, card on slot-3 , baseband-1,
and E1: 16th of that band.
2. Depending on the Traffic capacity of the card, you will see the number
of available free E1s for cross-connections. The naming convention is
self-explanatory.
3. Connections can be renamed or deleted as well.