TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 1 -
GPS Vehicle Tracker
v
USER MANUAL (Model: MT100)
Please read carefully before operation
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 2 -
Contents 1. Product overview ......................................................................................................................3 2. Applications ..............................................................................................................................3 3. Product Function and Specifications.........................................................................................4
3.1 Product function..................................................................................................................4 3.2 Specifications ......................................................................................................................5
4. MT100 and Accessories ............................................................................................................6 5. Installation.................................................................................................................................6
5.1 Installation SIM card...........................................................................................................6 5.2 Charging..............................................................................................................................7 5.3 LED Indications ..................................................................................................................7 5.4 Install I/O cable...................................................................................................................8 5.5 Power/GND.........................................................................................................................8 5.6 Digital Input (Negative Triggering) ....................................................................................9 5.7 Digital Input (Positive triggering) .......................................................................................9
6. Basic SMS commands: ...........................................................................................................10 6.1 Position report ...................................................................................................................10 6.2 Set function of receiving actual address name via SMS ...................................................11 6.3 Get location in Google map URL format ..........................................................................11 6.4 To cut off Engine, immobilize the vehicle ........................................................................12 6.5 Set over speed alarm .........................................................................................................12 6.6 Harsh acceleration/braking alert .......................................................................................12 6.7 Oil leaking/Refuel Alarm..................................................................................................13 6.8 Enable Impact Alarm Function: ........................................................................................13
7. Set SMS for GPRS tracking....................................................................................................14 7.1 Set ID by SMS ..................................................................................................................14 7.2 Set APN by SMS...............................................................................................................14 7.3 Set IP Address and Port by SMS.......................................................................................14 7.4 Enable GPRS Function .....................................................................................................14 7.5 Set Time Interval for Sending GPRS Packet.....................................................................15
8. Troubleshooting ......................................................................................................................16 Appendix 1 Configure by computer................................................................................................17 Appendix 2 Command List .............................................................................................................21 Appendix 3 Configure and use of RFID function ...........................................................................25
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 3 -
1. Product overview
MT100 is a kind of mini GPS vehicle tracking product can be used for tracking and security
of motorcycle and automobile etc. Mini size, built-in antenna and waterproof designed, easy
to be installed and concealed, with power voltage range from 6V~24V, therefore can satisfy
tracking and security demands for all kinds of vehicles.
2. Applications
Vehicle Real Time Tracking
Motorcycle/Car Security/Anti-Hijack
Fleet Management
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 4 -
3. Product Function and Specifications
3.1 Product function
OTA function (support over the air)
Harsh acceleration alert/Braking alert
Engine idle alert/low power alert/power failure alert
Oil leaking/Refuel alarm
ARM9 high speed microcontroller
Support active/passive RFID for anti-theft alert and driver identification
Fuel management
4M flash can save the maximum 26000 points data
6V~24V power supply
Track by SMS/GPRS (TCP/UDP)
Track by time interval
Track by distance interval
Anti-robbery with SOS button, call for help
Geo-fence alarm
Over speed alarm
Built-in motion sensor for power saving
Google map URL for location via SMS, which shows you location on map via mobile
phone
Get the physical address name via SMS
Remote engine cut
Mileage report
I/O: 3 Output, 2 Input, 1 Analog input and 1 RS232 port
Mini size, simple installation, low cost tracker for motorcycles, 12V and 24V vehicles
Monitor the voice (optional)
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 5 -
3.2 Specifications
Items Specifications
Dimension 80*58*22mm
Weight 92g
Charging voltage +9V~+24V
SIM Card type 3V
Power consumption Active mode(peak)<1.0 A Active mode(avg.)<300 Ma Idle mode <50 mA
Operating temperature -20~+75
Humidity Up to 75% non-condensing
External SIM card Connected via SIM card connector
External Antenna Connected via 50 Ω coax connector
Button 1 SOS and 1 power on/off
Microphone Optional
Transmit power Class 4(2W) for E-GSM 900 and 850 Class 1(1W) for DCS 1800 Class 1(1W) for PCS 1900
Sensitivity -104dBm minimum for E-GSM 900 AND 850 -102dBm minimum for DCS 1800 -102dBm minimum for PCS 1900
GPS chip Latest GPS SIRF-Star Ⅲ chipset
GPRS Multi-slot Class 8(4Rx, 1Tx., 5slot Max.) Support all 4 coding schemes(CS-1,CS-2,CS-3 and CS-4) Maximum download speed is 85.6kbps Maximum upload speed is 21.4kbps
Speech Codec Triple rate Codec Half rate—ETS 06.20 Full rate—ETS 06.10 Enhance full rate—ETS 06.50/06.06/06.08
I/O 3 Output, 2 Input, 1 Analog input and 1 RS232 port
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 6 -
4. MT100 and Accessories
MT100 Main Unit 8P wire harness Relay
Optional Accessories
Active RFID Kits Fuel Sensor Passive RFID Kits
5. Installation
5.1 Installation SIM card
Check that the SIM card has not run out of
credit (test the SIM card in a phone to make
sure it can send and receive SMS);
Before installing the SIM card, turn off the
power for MT100. Then install the SIM card as
following:
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 7 -
5.2 Charging
Connect the device with external power like car battery, and turn on its power switch, then it
will do charging automatically
5.3 LED Indications
Push the power switch to turn on/off MT100
GPS LED (Red)
Flashing ( every 0.1 second) Initializing or back-up battery power is low
Flashing (0.1 second on and 2.9 seconds off) MT01 has a GPS fix
Flashing (1 second on and 2 seconds off) MT01 has no GPS fix
GSM LED (Green) Flashing ( every 0.1 second) Initializing
Flashing (0.1 second on and 2.9 seconds off) MT01 is connected to the GSM network
Flashing (1 second on and 2 seconds off) MT01 is not connected to the GSM network
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 8 -
5.4 Install I/O cable
The I/O cable includes power,
Negative/positive Input and
Output
PIN Number Description
Output 3 E.g. connected with siren
AD 1 10 Bits Resolution Analog Inputs. 0~6V DC Detection. It can be used to connect with fuel
sensor etc.
Power DC In (power source). Input voltage: 9V~36V. 12V suggested.
GND Ground.
Output2 NC
Input1 Digital Input 1 (negative triggering), e.g. It can be connected with SOS panic button.
Output1 Output1. It can be used to connect with relay for engine immobilization.
Input4 Digital Input 4 (positive triggering), e.g. detecting the ACC.
RS232 Port It can be used to connect with RFID and Temperature Sensor etc.
5.5 Power/GND
Connect GND (-Black) and Power (+Red) wires to the battery of vehicle.
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 9 -
5.6 Digital Input (Negative Triggering)
E.g. Detecting SOS button
5.7 Digital Input (Positive triggering)
E.g. detecting engine on/off status
5.8 Output PIN IN and OUT 1 application example:
Input 1 or Input 2 or Input 3 White
SOS Button
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 10 -
6. Basic SMS commands:
6.1 Position report
Description: To know the position of your MT100,
send an SMS or make a telephone call directly to
MT100 and you will receive an SMS with its
location and other information.
Command: W<password>, 000
Note: The default password is 000000 (the following the same) Item Description ID: 1234567890 The tracker’s ID number ACC=OFF The engine is turned off Latitude=23 08 57.58N, longitude=113 18 59.31E
Latitude and longitude information, “N” in latitude means North ,”E” in latitude means East,
Speed=0.00Km/h Speed information Odometer=0.013km/h Odometer information 2012-09-26,11:32 Date and time
You can copy this coordinate get from the SMS into http//:maps.google.com and see its
location as below:
Another easier way to get MT100’s position:
Use your mobile phone to call the SIM number in the MT100, after hearing several times
ring, then hung up, MT100 will send a SMS with location information back to your mobile
phone.
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 11 -
6.2 Set function of receiving actual address name via SMS
Description: To know specific address of your MT100, send an
SMS and you will receive an SMS with its location physical
address name.
(This command needs our GPRS tracking platform GPRS-01 support)
Command: W<password>,111
Example:
SMS send: W000000, 111
SMS receive: Xinfu 1st Rd, Maonan, Maoming, Guangdong, China
6.3 Get location in Google map URL format
Description: You will get a Google map URL after sending the command, click the URL then
the location can be shown directly on Google Maps on your mobile phone.
Command: W<password>,100
Example:
SMS send: W000000,100
SMS Received: as following picture 1
Note: then by click the URL, you can get the location in Google map from your mobilephone,
see bellowing picture 2
1 2
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 12 -
6.4 To cut off Engine, immobilize the vehicle
Command: W<password>,020,P,F
Description: P=1, means output1, P=2 means output2 … P=5, means output5
F=0, to disable this output function; F=1, to enable this output function
Example:
SMS send: W000000,020,1,1
If the output1 is connect to oil-cut relay, this command is to enable the engine-cut function,
the engine oil pump line will be cut-off to immobilize the vehicle.
While send W000000,020,1,0 is to restore the engine oil pump line and the vehicle can be
started again.
6.5 Set over speed alarm
Command :W<password>,005,XX
Description: XX(the speed preset value) XX=00, disable XX=[01<XX<20](unit:10Km)
Example:
SMS send:W000000,005,10
SMS receive: SET OK! SPEED LIMIT:100Km/h
Meaning: If your speed is over 100Km/h, an alarm SMS will send to your phone to warn you.
6.6 Harsh acceleration/braking alert
SMS command: W<password>,047,X
Description: X means value of velocity change, 1 to 2 digitals. Default value is 0 for disable
acceleration/braking alert function.
(1) Acceleration Alert: When the speed is over 20km/h, if the speed increase over X km/h in 5
seconds, the tracker will trigger acceleration alert, send the alarm data to tracking platform, its
alarm code is 0x73.
Example:
SMS send: W000000,047,5
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 13 -
Meaning:When the speed is over 20km/h, if the speed increase over 5 km/h in 5 seconds, the
tracker will trigger acceleration alert, send the alarm data to tracking platform.
(2) Braking Alert: When the speed is over 20km/h, if the speed decrease over (X+10) km/h
in 5 seconds, the tracker will let out braking alert, send the alarm data to tracking platform,
the protocol number is 0x72.
Example:
SMS send: W000000,047,10
Meaning: When the speed is over 20km/h, if the speed decrease over 20 km/h in 5 seconds,
the tracker will let out braking alert, send the alarm data to tracking platform.
6.7 Oil leaking/Refuel Alarm
SMS command: W000000,094,X
Description: X = 000~199(unit: second), means for fuel capacity change exceed preset value
in the time interval X, it will send out oil leaking or fueling alarm, send alarm data to tracking
platform, the leaking protocol number is 0x74, the fueling protocol number is 0x76. And if X
is less than or equal to 5 seconds, then the function will be disabled. System default value is
10 seconds.
6.8 Enable Impact Alarm Function:
SMS command: W<password>,028.1
Meaning: If the vehicle impact , an alarm SMS will send to your phone to warn you
Disable Impact alarm function:
SMS command: w<password>,028,0
When sending out impact alarm, alarm data will be sent to platform, alarm code is 0x14
System’s default setting is disable function of impact alarm
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 14 -
7. Set SMS for GPRS tracking
7.1 Set ID by SMS
Command: W<password>,010,ID
Description: every tracker has a unique ID. Tracker ID must be less than 14 digitals
Example:
SMS send:W000000,010,20120823
Meaning: this tracker’s ID is 20120823
7.2 Set APN by SMS
Command: W<password>,011,APN name,APN username, APN password
Description: W<password>,011, APN name, APN username, APN password
if no username and password required, just put in APN name only.
7.3 Set IP Address and Port by SMS
Command :W<password>,012,IP,Port
Description: Our online tracking website’s IP address is 210.209.68.180 Port is 9500
Example:
SMS send: W000000,012,210,209,68,180,9500
We support domain name instead of IP address:
Example: W000000,012,www.global-track.net,9500
7.4 Enable GPRS Function
Command: W<password>,013,X
Description: X=0, close GPRS (Default)
X=1, enable TCP
X=2, enable UDP
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 15 -
7.5 Set Time Interval for Sending GPRS Packet
Command :W<password>,014,XXXXX
Description: XXXXX should be in five digitals and in unit of 10 seconds.
XXXXX =00000, to disable this function
XXXXX =00001~65535, time interval for sending GPRS packet and in
unit of 10 seconds
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 16 -
8. Troubleshooting
Problem: Unit will not turn on
Possible Cause Resolution
Wiring was not connected properly Check and make sure wiring connection is on order
Battery needs charging Recharge battery
Problem: Unit will not respond to SMS
Possible Cause Resolution
GSM antenna was not installed properly
Make MT100 connected to GSM Network.
GSM Network is slow Wait for SMS. Some GSM networks slow down during peak times or when they have equipment problems.
Wrong password in your SMS Insert the correct password The SIM in MT100 has run out of credit
Replace or top up the SIM card
No SIM card Insert working SIM card. Check in phone that the SIM can send SMS messages.
SIM card has expired Check in phone that the SIM can send SMS messages. Replace SIM card if needed.
SIM has PIN code set Remove PIN code by inserting SIM in you phone and deleting the code
SIM is warped or damaged Inspect SIM, clean the contacts. If re-inserting does not help try another to see if it will work.
Roaming not enabled If you are in a different country your SIM account must have roaming enabled
Battery is low Recharge the unit and the GSM will start working.
Problem: SMS from MT100 states “last......”
Possible Cause Resolution
Unit does not have clear view of the sky
Move the antenna of the unit to a location where the sky is visible.
MT100 is in an inner place Wait for the target to come out
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 17 -
Appendix 1 Configure by computer
This part shows the basics of how to use the TOPSHINE Parameter Editor. Note: Don’t
connect MT100 to external battery when configuring.
How to Edit the Parameters of MT100
Step 1 Buy one specific USB cable for configuration from Our Company
Step 2 Install USB driver program for the configuration USB cable
1. Run “CP210x_Prolific_DriverInstaller” to install the driver for the USB data cable.
Note: CP210x_Prolific_DriverInstaller is in the folder ‘USB-232 Driver’ in the CD.
Connect the USB Data Cable between MT100 and PC.
2. Connect the configuration cable with PC, open device management of your computer.
You can find “Prolific USB-to-Serial Comm. Port ” , as following picture shows.
The USB port is virtual comm. Port (com3) in this example,
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 18 -
Step 3 Open the GPS Tracker Parameter Editor
1. Connect MT100 with PC by the configuration cable
2. Confirm MT100 is in the Power Off states
3. Double click GPS Tracker Parameter Editor.exe and Select the COM Port, following
picture shows:
4. Click Start button to open the com port.
5. Turn on MT100and it will connect with the Editor automatic, As soon as they connect
successful, all the buttons are availability and the status bar will clue on’ Tracker Connect!’ ,
then you can Read or Write the MT100’s Parameters
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 19 -
Instruction of parameter setting:
Item Description
GPRS Tick to enable GPRS function, select TCP or UDP
mode
Tracker ID Should be unique, in number, maximum 14 bytes
APN, APN Account, APN
Password
Put your local APN, APN username and password if
necessary
IP, Port Put online tracking server IP and port, our default is IP:
www.global-track.net port: 9500
Interval To put time interval to upload a data
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 20 -
Item Description SMS tracking No. Interval To put a mobile phone number for automatic tracking
by SMS at certain time interval in minutes
Password To set SMS command password, the default is
000000,
Over Speed To set speed limit for over speed alarm
Prefix(area code) To set country code
Time Zone To set time zone, GMT*60 (minutes), if in west half
western hemisphere, “-” is necessary to put ahead
Wiretapping To set wiretapping mobile phone number
Distance To set track and upload data by certain distance in
meters
Power Saving To set time enter into standby mode when shaking
not detected to save power and gprs data traffic
Course To set upload data via angle shifting by certain angles
Item Description SMS Call SOS
Button/IN1
To set Mobile phone No. for SMS or Calling when SOS
button/Input 1 is triggered
SMS Call Button
B/IN2
To set Mobile phone No. for SMS or Calling when Button
B/Input 2 is triggered
SMS Call Button
C/IN3
To set Mobile phone No. for SMS or Calling when Button C/Input
3 is triggered
SOS Button/IN1 To customize the reply SMS text when SOS Button/Input 1 triggered
Button B/IN2 To customize the reply SMS text when Button B/Input 2 triggered
Button C/IN3 To customize the reply SMS text when Button C/Input 3 triggered
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 21 -
Call for SMS Tick it to reply SMS when calling in
Cut off Power Tick it to send alert when the external power
be cut off
Appendix 2 Command List
Presetting by SMS for GPRS tracking Set ID for MT100 by SMS W******,010,ID Tracker ID must be less than 14
digits
Set APN by SMS W******,011,APN,APN Name, APN Password
APN Name, APN Password If no
password required, just insert
APN
name only;
APN defaulted as ‘CMNET’;
APN name + password not over
39
characters.
Set IP Address and Port by
SMS
W******,012,IP, Port IP: xxx.xxx.xxx.xxx
Port: [1,65536]
Enable GPRS Function W******,013,X X=0, close GPRS (default);
X=1, enable TCP
X=2, enable UDP
Set Time Interval for
Sending GPRS Packet
W******,014,XXXXX XXXXX should be in five digitals
and in
unit of 10 seconds.
XXXXX=00000,to disable this
function;
XXXXX=00001~65535, time
interval for sending GPRS
packet and in unit of 10 seconds.
Output Control W******,020,P,F P =1, Out1
=2, Out2
=3, Out3
=4, Out4
=5, Out5
F =0, to disable the output
=1, to enable the output
Output Control (Safe mode)
W******,120,ABCDE ABCDE represents Out1, Out2,
Out3,
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 22 -
This function is achievable
when the speed is below
10km/h and GPS is
available.
Out4, Out5 respectively.
If A or B or C or D or E,
=0, to disable the output
=1, to enable the output
=2, to remain previous status
Set power saving mode when MT100 is still (In power saving mode,
GPS stops working. GSM
enters standby mode and
stop sending out message
until it is activated by an
SMS or an incoming call)
W******,026,XX XX=00, to disable this function
XX=01~99, to set this function. It
is in
unit of minute.
Example:
If XX=10, MT100 will enter
power
saving mode in 10 minutes after
it is
immobile.
Set phone number for wiretapping
W******,030,T T is the telephone number for
wiretapping and max. 16 digits
Set time zone difference W******,032,T T=0, to disable this function
T=[1, 65535] to set time
difference in
minutes to GMT.
Default value is GMT
+, not necessary for those ahead
of
GMT. For example, either +120
or 120
is acceptable.
-, required for those behind GMT.
For
example, -120.
Set character for SOS alert message
W******,033,P,Char Char P is the button number.
P=1, 2, or 3.
Char is the character in SOS
message
and max 32 characters
Set tracking by driving angle change function
W******,036,Degree
Measured by Degree(s),
Degree=0,disable this function;
X=1-359 , means set angle
degree interval in this function.
Set tracking by distance function
W******,045,X Measured by Meter(s),
X=0, disable this function ;
X=1—65535 , means the
distance interval in this function.
Set clear/reset odometer W******,046 To clear and reset odometer
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 23 -
function information to zero.
Set function of receiving location physical address name via SMS
W******,111
This function needs support of
the GPRS01 or SMS01 tracking
platform, address SMS will be
received in text format.
Get version and serial number
W******,600 To get version and serial number
of
current firmware
Get IMEI No. W******,601 To get device IMEI No.
Reboot GPS and GSM Module
W******,900### ### is the ending character.
Initialization To turn all the parameters /
settings (except for the
password) to factory default.
W******,990,099### ### is the ending character.
Password Initialization
W888888,999,666 This command will reset the
current password to factory
default password 000000
Description Command Remarks
Get current location
W******,000 Get current location of MT100
Get location in Google map URL format via SMS
W******,100 http://maps.google.com/map
s?f=q&hl=en&q=22.542563
,114.077971&ie=UTF8&z=
16&iwloc=addr&om=1
Change user’s password
W******,001,######
****** is old password
###### is new password
Set interval for automatic timed reports
W******,002,XXX XXX is the interval in minute. If
XXX=000 it will stop tracking
Set preset phone number for SOS button
W******,003,F,P,T F=0, to disable this function;
F=1, only sending SMS;
F=2, only calling preset phone number;
F=3, both SMS and calling (default)
P is the button number and should be 1,or 2, or
3.
If SOS button is linked to IN1, then P=1.
T: Preset phone number
(T must be less than 16 digits)
Set over speed alarm When MT100
W******,005,XX XX (the speed preset value)
=00 , disable
=[01<XX<20] (unit: 10Km)
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 24 -
speeds higher
than the preset
value, it will
send one over
speed alarm
SMS to the SOS
preset
number.
Set Geo-fence alarm (foursquare) When the MT100
moves out
of preset scope, it
will send
one Geo-fence
SMS to the
SOS preset
number.
W******,006,XX XX (set distance from current central point
place )
=00, disable
=01, 30m
=02, 50m
=03, 100m
=04, 200m
=05, 300m
=06, 500m
=07, 1000m
=08, 2000m
Extend Settings W******,008,ABCDEFGHIJ###
A=0, disable position report function
when a call is made to MT100
A=1, enable position report function to
get position SMS by Calling MT100
I=0, disable power failure alert
I=1, enable power failure alert
The functions of BCDEFGHJ are
remained for furthur use.
### is the ending character.
Set Geo-fence alarm 017 command is
for alarm when
tracker moves out
the preset scope;
117 command is
for alarm when
tracker moves in.
When the tracker
moves in or out, it
will send an SMS
alarm to the
authorized phone
number for SOS.
W******,017,data W******,117,data
data is the coordinates which include:
Lower-left X, Lower-left Y,Upper-right
X,Upper-right Y
Forexample,
11404.0000,E,2232.0010,N,11505.1234,E,2333.
5678,N
Note:1. Lower-left X,Y (longitude and latitude)
should be smaller than Upper-right X,Y;
2. All longitudes and latitudes should be in ASCII
format as follows:-
Longitude: DDDMM.MMMM,E/W. 4 places of
decimal. ‘0’ is needed to be stuffed if no value
available.
Latitude: DDMM.MMMM,N/S. 4 places of
decimal. ‘0’ is needed to be stuffed if no value
available;
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 25 -
3. Send W******,017 or W******,117 without data
to disable this function.
Appendix 3 Configure and use of RFID function
RFID Reader RFID Tag
1. Install RFID as following:
2. How to use
2.1 SMS Commands
2.1.1 Enable the RFID:
(1) Enable the RFID function:W000000,062,1
(2) Disable the RFID function: W000000,062,0
(3) The system default is RFID function enabled.
(4) When send the disarming SMS command ”000000DSM”, it will automatic disable the
RFID function, and if send the enable SMS command the RFID function will be restored.
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 26 -
2.1.2 To configure authorized RFID tag by SMS commands
W<password>,060,num1
W<password>,160,num2
W<password>,260,num3
W<password>,360,num4
W<password>,460,num5
Note: The default password is 000000
Num1, num2, num3, num4, num5 means 5 digital FRID number.
For example: if configure NO.00412 as the authorized RFID tag, then send SMS:
W000000,060,00412
Tracker will reply SMS “STUDY ID OK: 1:00412; 2:00000; 3:00000; 4:00000; 5:00000”,
means the 1st RFID tag number is 00412, the 2nd , 3rd, 4th, 5th RFID tag not set. If the RFID
tag is detected at this time, tracker will send SMS “NOW ID : 00412 “ .
Note: RFID reader detecting test RFID tag distance is within 5 meters, the RFID tag
must be detected before RFID can be used.
2.1.3 The ARMING SMS command: “<password>ARM ”
The disarming SMS command “<password>DSM ”,
When send the disarming SMS command “000000DSM”, it will automatic disable the
RFID function, and if send the enable SMS command the RFID function will be restored.
Another way to configure authorized RFID tag by Parameter.
Step 1: Open GPS Tracker Editor (2010) V2.65 (following picture)
(Following Appendix 1 to configure the tracker)
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 27 -
Turn on MT100 and it will connect with the Editor automatic, As soon as they connect
successful, all the buttons are availability and the status bar will clue on’ Tracker Connect!’ ,
then you can Read or Write the MT100’s Parameters
Step 2: Finding RFID Settings (as following picture). Following the digital sort to do: 1.
write the RFID tag’s number, (example: 00412) 2. click Apply, then display “com operate
success” ,click the OK; 3. Click the Read. 4. Then it will display “412” it prove already
configure authorized RFID tag succeed. If you want to configure multiple RFID tags, just like
the example “00412,00234,00322,*****”; after write success, it will display”
412,234,322,***”
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 28 -
2.1.4 Judge if need to cut off oil/fuel supply when the ignition alert occurs to stop engine
start.
Enable function of cutting off oil-way when illegally ignite under ARM status
SMS command: W<password>,061,1
Disable function of cutting off oil-way when illegally ignite under ARM status
SMS command: W<password>,061,0
The system default setting is disable function of cutting off oil-way when illegally igniting
under ARM status.
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 29 -
3. Command List
Description Command Reply SMS
Configure authorized RFID tag W<password>,060,num1 W<password>,160,num2 W<password>,260,num3 W<password>,360,num4 W<password>,460,num5
STUDY ID OK: 1:num1; 2:num2;
3:num3; 4:num4; 5:num5;
The next SMS: NOW ID………
Enable the RFID detection W<password>,062,1 ENABLE OK !
Disable the RFID detection W<password>,062,0 DISABLE OK !
Arm <password>ARM Vehicle is armed!
Disarm <password>DSM
Enable function of cutting off
oil-way when illegally ignite
under ARM status
W<password>,061,1
Disable function of cutting off
oil-way when illegally ignite
under ARM status
W<password>,061,0
System default setting is disable
function of cutting off oil-way
when illegally ignite under ARM
status.
4. Functions
4.1 To ignite in armed status, it will check the RFID tag. If an authorized tag can be
detected, it will not alert. If an authorized tag can not be detected, it will send alert SMS
“Engine Is On!” to three authorized alert mobile phone numbers, and at the same time, the
Output 3 will control siren to sound, and call the three mobile phones at one minute interval,
and decide to cut off the oil/fuel supply according to its oil cut enable/disable status.
4.2 If vehicle door is opened in armed status, it will check the RFID tag. If an authorized
tag can be detected, it will not alert; if an authorized tag can not be detected, it will send alert
SMS “Door Is Open !” to three authorized alert mobile phone numbers, and the Output 3 will
control the siren to sound, and call the three mobile phone numbers at one minute interval.
4.3 If the vehicle is moved/towed in armed status, it will detect the RFID tag, if no
authorized tag be detected, it will send alert SMS ”Movement alarm!” to the 1st alert mobile
phone number.
4.4 In disarmed status, if no authorized RFID tag Is detected for successive 30 seconds,
then the system will automatically arm the vehicle, and it will call the 1st alert mobile phone
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 30 -
number, after several rings and hang off automatically, indicating the vehicle be armed.
4.5 If alert be triggered, the siren will sound for 10 seconds and shut or immediately shut
when disarm action is detected.
4.6 If illegal ignition be detected and oil/fuel supply cut off enabled, then the oil/fuel
supply will be cut off, and it will be immediately restored as soon as disarm action be
detected.
4.7 If the oil/fuel supply is cut off by SMS or GPRS platform, it can not be restored by
disarm action.
5. RFID on the platform applications
5.1 Into our GPS Tracking Platform: http;//www.global-track.net, as following picture
P1,login interface, as following picture P2
P1 P2
5.2 Select your device, such as instructed 1; it will display your car’s the current
information, Driver (ID) means the driver and his/her RFID tag number such as instructed 2;
5.3 If you want to edit the driver information, please click “manage” ,such as instructed 3,
then interface will into as following picture P3;
TOPSHINE TRACKING TECHNOLOGY USER MANUAL OF MT100
- 31 -
5.4 Click Driver Manage , such as instructed 4;it will open such as instructed A;
You can click New, such as instructed 5, open as following picture P4; to add tag ID and the
driver’s information etc.