Page 1/12
Torque sensorwith dual-range-option
4503
B_00
0-76
7e-0
8.20
Torque
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Type 4503B...
Type 4503B... torque sensors with built-in speed sensor oper-ate on the strain gage principle. An integral, digital measure-ment conditioning system produces analog or digital output signals.
• Rated torque: 0,2 ... 5 000 N∙m• Ratio for second range: 1:10 or 1:5 of rated torque• Speed ranges up to 50 000 1/min• Accuracy class in standard measuring range: 0,05/0,1
In the extended measuring range: 0,1/0,2/0,4• Integral speed sensor, high resolution speed/angle meas-
urement sensor up to 8 192 pulses/revolution as option• Serial data output RS-232C and USB interface
Additional advantages of second range:• Freely selectable torque output frequency or voltage• One sensor for two separately calibrated measuring ranges
DescriptionThe dual range sensor offers the advantage of freely scalable range switching, which allows highly accurate measurement of both the peak and particularly the operating torque.
The sensor offers an integrated high resolution speed/angle measurement sensor up to 8 192 pulses/revolution, freely scal-able. Additionally, the rotational direction as well as an abso-lute zero point (Z-line) are available.
Power is supplied and the measurement signals transferred between the rotating shaft and the case without contact. In addition to suitable mounting of the shaft, low production tol-erances and high grade balancing, this is a further prerequisite for the high speed limit of up to 50 000 1/min achieved with the "H" version.
ApplicationThe Type 4503B... torque sensors are used:
• In automotive and vehicle engineering• In the aeronautical industry• In mechanical and process plant engineering• In electric motor manufacture
They are universal in application, being suitable for the devel-opment laboratory, production or quality assurance.
With a torque sensor Type 4503B... you will solve your meas-urement requirement. They are typically used for testing of electric motors, generators, drive performance, measurement of transmission or spindle drive friction, at a manual worksta-tion or in networked, automated production cells.
Page 2/12
Torque sensor – with dual-range-option, Type 4503B...45
03B_
000-
767e
-08.
20
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Technical data
Mechanical basic data
Measuring range N∙m ±0,2 ... 5 000
Rated torque Mnom N∙m 0,2 ... 5 000
Overload capacity at limiting torque 1,5 x Mnom
Alternating torque 0,7 x Mnom
Rupture torque 4 x Mnom
Built-in speed sensor pulses/
speed measurement optional revolut. 1x60
Minimum rotational speed for min-1 >2
sufficient pulse stability
Nominal Speed depending on
measuring range and
design (see details)
Balancing class Q
for version "L" and "W" 6,3
for version "H" 2,5
Housing material Anodized aluminum
Protection class IP40
General electrical specifications
Cut-off frequency −3 dB for kHz 10
voltage output
Group delay Moment at 10 kHz µs <220
Noise with TP filter with Hz 1 000
Cut-off frequency (−3 dB) in % FSO <±0,05
measuring range 1:1
Output signal VDC ±0 ... 5/10
at Mnom (rated value) kHz 100 ±40
Load resistance kΩ >10
Operating temperature range °C 10 ... 60
(rated temperature range)
Service temperature range °C 0 ... 70
Storage temperature range °C −25 ... 80
100 % control input VDC "On" 3,5 ... 30
"Off" 0 ... 2
Supply voltage VDC 11 ... 30
Power consumption W <10
Electrical connection 12 pin/7 pin
built-in connector
Speed/Rotation angle measuring system (optional)
Size 1 ... 5
Measuring system magnetoresistive
Output signal V 5 TTL
Pulses per revolution (N) 2x 1 … 8 192
Pulse tolerance (Jitter of each flank) ° ±0,03
Minimum rotational speed for
sufficient pulse stability min-1 >0
Admissible maximum
output frequency fout kHz 500 1)
Group delay µs <100
Load resistance kΩ ≥2
Jitter of the oscillation period (Jp) % Jp = (0,03°/180°) x N x 100
1) Maximum numbers of output pulses Nmax = maximum allowable output fre-quency fout (Hz) x 60 / rotational speed n (min-1).With 8 192 pulses means a maximum speed of 3 660 min-1
Reference pulse measuring system (0-Index)
Measuring system magnetoresistive
Output signal V 5 TTL
Pulses per revolution 1
Pulse tolerance ° ≤0,03
Minimum rotational speed for
sufficient pulse stability min-1 >0
Group delay µs <100
Load resistance kΩ ≥2
Noise immunity (EN 61326-1, Table 2)
Electromagnetic field (AM) V/m 10
Magnetic field A/m 100
Electrostatic discharge
Contact discharge (ESD) kV 8
Electrostatic discharge
Air discharge (ESD) kV 4
Fast transients (burst) kV 1
Impulse voltage (surge) kV 1
Conducted emissions (AM) V 10
Mechanical shock (EN 60068-2-27)
Number of cycles – 1 000
Cycle time ms 3
Acceleration shock g 650
Vibrational loads in 3 directions (EN 60068-2-6)
Frequency range Hz 10 ... 2 000
Load duration h 2,5
Acceleration (Amplitude) g 200
Page 3/12
Torque sensor – with dual-range-option, Type 4503B...45
03B_
000-
767e
-08.
20
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Size/Rated torque Mnom
N∙m 0,2 0,5 1 2 5 10 20 50 100 200 500 − − −
kN∙m − − − − − − − − − − − 1 2 5
Torque measuring system
Nominal speed nnom
Version "L" + "W" (Low Speed) min-1 20 000 12 000 8 000 5 000
Version "H" (High Speed) min-1 50 000 30 000 20 000 10 000
Measurement features in the measuring range 1:1 (single range)
Accuracy class 0,1 0,05
Linearity error including hysteresis
% FSO <±0,1 <±0,05
Rel. standard deviation ofrepeatability
% FSO <±0,1 <±0,05
Temperature influence zero point %/10 K <±0,1 <±0,05
Temperature influence nominal value %/10 K <±0,1 <±0,05
Size/Rated torque Mnom
N∙m 0,2 0,5 1 2 5 10 20 50 100 200 500 − − −
kN∙m − − − − − − − − − − − 1 2 5
Measurement features in the measuring range 1:5 / 1:10
Accuracy class 0,4 0,2 0,1
Linearity error including hysteresis
% FSO <±0,4 <±0,2 <±0,1
Rel. standard deviation ofrepeatability
% FSO <±0,4 <±0,2 <±0,1
Temperature influence zero point %/10 K <±0,4 <±0,2 <±0,1
Temperature influence nominal value %/10 K <±0,4 <±0,2 <±0,1
Measurement features
Page 4/12
Torque sensor – with dual-range-option, Type 4503B...45
03B_
000-
767e
-08.
20
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Other technical data
Size/Rated torque Mnom
N∙m 0,2 0,5 1 2 5 10 20 50 100 200 500 − − −
kN∙m − − − − − − − − − − − 1 2 5
Mechanical basic data
Torsional rigidity cT kN·m/rad 0,08 0,15 0,38 0,78 1,72 2,70 11,7 15,2 74,0 97,8 134 506 685
Torsion angle at Mnom ° 0,14 0,35 0,38 0,30 0,37 0,33 0,43 0,25 0,38 0,15 0,29 0,43 0,23 0,42Proportional mass moment of inertia of rotor measuring side
kgcm2 0,051 0,052 0,062 0,47 0,48 6,90 6,96 7,14 59,1 61,0
Proportional mass moment of inertia of rotor drive side
kgcm2 0,285 0,285 0,276 0,71 0,72 5,99 6,41 6,59 58,7 60,6
Mass moment of inertia rotor kgcm2 0,336 0,337 0,338 1,18 1,19 12,9 13,4 13,7 118 122Natural frequency of the rotor (torsional vibration)
kHz 1,16 1,51 1,95 1,99 2,55 2,55 2,46 2,99 1,88 2,33 2,70 1,67 1,96
Balancing class according to DIN ISO 1940
Version "L" + "W" (Low Speed) − G 6,3
Version "H" (High Speed) − G 2,5Nominal lifetime of bearings L10h ac-cording to ISO2815 2815)
Version "L" + "W" (Low Speed) h 18632 24400 23900 21500
Version"H" (High Speed) h 12009 16275 11470 14638
1) Depending on rated torque2) Please note the maximum permissible torque (TKmax) of the coupling!3) The effects of permissible parasitic forces can be up to 1 % of nominal torque. Each type of irregular stress (Longitudinal or transverse force) is only permitted up to its specific load limit, provided none of the others will occur at the same time. If this condition is not met, the limit values must be reduced. If 50 % of Transverse load limit occur at the same time, only 50 % of Longitudinal load limit is permissible and the nominal (rated) torque must not be exceeded.4) The nominal torque must not be exceeded!5) Nominal life in operating hours, which is reached or exceeded by 90 % of a sufficiently large number of identical bearings before the first signs of material fatigue occur. The specified values are only valid if the load, speed, oscillation, shock and temperature limits are observed.
General technical data
Size/Rated torque Mnom
N∙m 0,2 0,5 1 2 5 10 20 50 100 200 500 − − −
kN∙m − − − − − − − − − − − 1 2 5
Load limits1)
Limiting torque, referred to Mnom2) % 150
Rupture torque, referred to Mnom % >400Oscillation width according to DIN 50100 (peak / peak)4) % 70
Version "L" + "W" (Low Speed)Longitudinal load limit on the drive side3) N 80 150 250 450
Transverse load limit on the drive side3) N 120 280 700 1 500Longitudinal load limit on the measurement side3) N 50 80 120 200 350
Transverse load limit on the measurement side3) N 1,6 3,3 5 10 28 30 35 200 450 700
Version "H" (High Speed)Longitudinal load limit on the drive side3) N 30 75 170 250
Transverse load limit on the drive side3) N 100 200 400 800Longitudinal load limit on the measurement side3) N 30 40 100 160
Transverse load limit on the measurement side3) N 1,6 3,3 5 10 28 30 35 100 250 450
Page 5/12
Torque sensor – with dual-range-option, Type 4503B...45
03B_
000-
767e
-08.
20
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Dimensions Type 4503B..., Measuring ranges 0,2 / 0,5 / 1 / 2 and 5 / 10 and 20 N∙m
Werkstückkanten nach ISO 13715
-0,2 +0,25
Allgemeintoleranzen
Längenmasse
Abmasse
Winkelmasse kürz. Schenkel
Abmasse
...10
±0°20'
* ...0,5
> 10...50
>0,5...3 >120...400 >400..1000
±0°30'
>400...
±0,1 ±0,5
> 3...6 > 30...120
> 50...120
±0,3
±1°
±0,2 ±0,8
±0°10'
>120...400
*=KISTLER-Norm
±0,1±0,05
> 6...30
±0° 5'
ISO 2768-mH
d
g6
L1
90
d
g6
B
A 90
L G
25
L2
E
D
H
E
25
M
1 112
±0,
1
10 H7 4,1
38
38
30 65
C
125
Tk
11
100
M T(4x 90° = 360°)
1
M
Option Zubehör Gehäuseunterbau "GU"
Messseite
DM-Sensor 4503B 0,2+0,5+1 Nm CADENASBG1 CADENAS Masszeichnung
A4 a1 / 1
1:5
measure. analyze. innovate.
Erstmals verwendet
Erste Proj.-Nr.
Werksto
Änderung Datum MassstabErsatz für Kopie Datum
100012154
gez.
gepr.
ges.
30.10.2015 KebKeb27.06.2016Keb27.06.2016 100.247.704Zeichnungs-Nr.
Material-Nr.
KIWAG-SWX_A4h
Ver.Bl.
siehe Tabelle
interne und externe Fertigung
Das
Urh
eber
rech
t an
dies
er Z
eich
nung
, die
dem
Em
pfän
ger
pers
önlic
h an
vert
raut
wird
, ver
blei
bt u
nser
er F
irma.
Ohn
e un
sere
sch
riftli
che
Gen
ehm
igun
g da
rf d
ie Z
eich
nung
wed
er k
opie
rt n
och
verv
ielfä
ltigt
, noc
h an
Drit
tper
sone
nm
itget
eilt
oder
zug
ängl
ich
gem
acht
wer
den.
31.01.2017
Dimensions size 1 and 2 in mm Dimensions for mounting base (GU)
= Option mounting base "GU"M = Measuring end
Fig. 1: Type 4503B... Size 1 and 2All dimensions without tolerances comply with ISO 2768-mH
Size 1 2
Rated torque N∙m 0,2 0,5 1 2 / 5 10 / 20
L 159 163 167L1 16 18 20L2 16 18 20øD 58 58 58
ød g6 9 10 12A 22,5 24,5 26,5B 18 20 22C 18 18E 30 30G 122 122H 61,5 61,5
øTk 46 46M M5 (4x90 °) M5 (4x90 °)T 6 deep 6 deep
Werkstückkanten nach ISO 13715
-0,2 +0,25
Allgemeintoleranzen
Längenmasse
Abmasse Winkelmasse kürz. Schenkel Abmasse
...10±0°20'
* ...0,5
> 10...50
>0,5...3 >120...400 >400..1000
±0°30'>400...
±0,1 ±0,5> 3...6 > 30...120
> 50...120±0,3
±1°
±0,2 ±0,8
±0°10'>120...400
*=KISTLER-Norm
±0,1±0,05> 6...30
±0° 5'
ISO 2768-mH
74 -00,5
90 ++0,30,1
109,5 ±0,15
117,5 ±0,15
58
122
22
±0,1
10 70 ±0,1
A
A
8 ±0
,02
25 -00,02
28
M5
4x
5
A-A
KIWAG-SWX_A3q / Vers. 21-Sep-2017
Das
Urh
eber
rech
t an
dies
er Z
eich
nung
, die
dem
Em
pfän
ger
pers
önlic
h an
vertr
aut w
ird, v
erbl
eibt
uns
erer
Firm
a.O
hne
unse
re s
chrif
tlich
e G
eneh
mig
ung
darf
die
Zeic
hnun
gw
eder
kop
iert
noch
ver
viel
fälti
gt, n
och
an D
rittp
erso
nen
mitg
etei
lt od
er z
ugän
glic
h ge
mac
ht w
erde
n.
interne und externe Fertigung
siehe Tabelle
3.23154503B
Bl. Ver.
Material-Nr.
Zeichnungs-Nr. 100.421.387
Rou29.05.2019
ges.
gepr.
gez.
Kopie DatumErsatz für MassstabDatumÄnderung
Werkstoff
Erste Proj.-Nr.
Erstmals verwendet
measure. analyze. innovate.
1:1
1 / 1 0A3
Abmessungen GU 4503B0,2-20
Connecting dimensions for mounting base Size 1 and 2
N∙m Tightening torque0,2 / 0,5 / 1
6 N·m (strength class of the screw: 8.8)2 / 5
10 / 20
All dimensions without tolerances comply with ISO 2768-mH
Page 6/12
Torque sensor – with dual-range-option, Type 4503B...45
03B_
000-
767e
-08.
20
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Dimensions Type 4503B..., Measuring ranges 50 / 100 N∙m
Werkstückkanten nach ISO 13715
-0,2 +0,25
Allgemeintoleranzen
Längenmasse
Abmasse Winkelmasse kürz. Schenkel Abmasse
...10±0°20'
* ...0,5
> 10...50
>0,5...3 >120...400 >400..1000
±0°30'>400...
±0,1 ±0,5> 3...6 > 30...120
> 50...120±0,3
±1°
±0,2 ±0,8
±0°10'>120...400
*=KISTLER-Norm
±0,1±0,05> 6...30
±0° 5'
ISO 2768-mH
d
g6
L2
d
g6
L1
90
H
A
25 25
G
B
L
E E 113
M
1 112
±0,1
38
D
40
10 H7
4,1
C
125
60
11
100
68
Tk
M T(4x 90° = 360°)
Messseite
Option Zubehör Gehäuseunterbau "GU"
M
1
DM-Sensor 4503B 50_100 Nm CADENASBG3 CADENAS Masszeichnung
A4 a1 / 1
1:5
measure. analyze. innovate.
Erstmals verwendet
Erste Proj.-Nr.
Werkstoff
Änderung Datum MassstabErsatz für Kopie Datum
100012154
gez.
gepr.
ges.
13.07.2015 KebKeb27.06.2016Keb27.06.2016 100.240.790Zeichnungs-Nr.
Material-Nr.
KIWAG-SWX_A4h
Ver.Bl.
siehe Tabelle
interne und externe Fertigung
Das
Urh
eber
rech
t an
dies
er Z
eich
nung
, die
dem
Em
pfän
ger
pers
önlic
h an
vertr
aut w
ird, v
erbl
eibt
uns
erer
Firm
a.O
hne
unse
re s
chrif
tlich
e G
eneh
mig
ung
darf
die
Zeic
hnun
gw
eder
kop
iert
noch
ver
viel
fälti
gt, n
och
an D
rittp
erso
nen
mitg
etei
lt od
er z
ugän
glic
h ge
mac
ht w
erde
n.
28.06.2016
Dimensions size 3 in mm Dimensions for mounting base (GU)
= Option mounting base "GU"M = Measuring end
Fig. 2: Type 4503B... Size 3All dimensions without tolerances comply with ISO 2768-mH
Werkstückkanten nach ISO 13715
-0,2 +0,25
Allgemeintoleranzen
Längenmasse
Abmasse Winkelmasse kürz. Schenkel Abmasse
...10±0°20'
* ...0,5
> 10...50
>0,5...3 >120...400 >400..1000
±0°30'>400...
±0,1 ±0,5> 3...6 > 30...120
> 50...120±0,3
±1°
±0,2 ±0,8
±0°10'>120...400
*=KISTLER-Norm
±0,1±0,05> 6...30
±0° 5'
ISO 2768-mH
82 + 0,50
89 ±0,15
28
±0,1
5
97,5
12
68
113 ±0,15
A
A
M8
2x
8
10
+ +0,03
0,01
4,5
78
A-A
KIWAG-SWX_A3q / Vers. 21-Sep-2017
Das
Urh
eber
rech
t an
dies
er Z
eich
nung
, die
dem
Em
pfän
ger
pers
önlic
h an
vertr
aut w
ird, v
erbl
eibt
uns
erer
Firm
a.O
hne
unse
re s
chrif
tlich
e G
eneh
mig
ung
darf
die
Zeic
hnun
gw
eder
kop
iert
noch
ver
viel
fälti
gt, n
och
an D
rittp
erso
nen
mitg
etei
lt od
er z
ugän
glic
h ge
mac
ht w
erde
n.
interne und externe Fertigung
siehe Tabelle
3.23154503B
Bl. Ver.
Material-Nr.
Zeichnungs-Nr. 100.421.410
Rou29.05.2019
ges.
gepr.
gez.
Kopie DatumErsatz für MassstabDatumÄnderung
Werkstoff
Erste Proj.-Nr.
Erstmals verwendet
measure. analyze. innovate.
1:1
1 / 1 0A3
Anschlussmaße GU 4503B50-100
Connecting dimensions for mounting base Size 3
N∙m Tightening torque
50 25 N·m (strength class of the screw: 8.8)100
Size 3
Rated torque N∙m 50 / 100
L 180L1 28L2 28øD 78
ød g6 22A 43,5B 34C 18E 30G 113H 64,5
øTk 64M M6 (4x90 °)T 12 deep
All dimensions without tolerances comply with ISO 2768-mH
Page 7/12
Torque sensor – with dual-range-option, Type 4503B...45
03B_
000-
767e
-08.
20
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Dimensions Type 4503B..., Measuring ranges 200 / 500 / 1 000 N∙m
Werkstückkanten nach ISO 13715
-0,2 +0,25
Allgemeintoleranzen
Längenmasse
Abmasse Winkelmasse kürz. Schenkel Abmasse
...10±0°20'
* ...0,5
> 10...50
>0,5...3 >120...400 >400..1000
±0°30'>400...
±0,1 ±0,5> 3...6 > 30...120
> 50...120±0,3
±1°
±0,2 ±0,8
±0°10'>120...400
*=KISTLER-Norm
±0,1±0,05> 6...30
±0° 5'
ISO 2768-mH
d
g6
L1
B
10
G
L
d
g6
90 A
H
25 25
L2
E E 137
M
1
125
C
38
34 60
115
105
10 H7
4,1
112
±0,1
5
100
13
Tk
D
51
M T(4x 90° = 360°)
Messseite
Option Zubehör Gehäuseunterbau "GU"
M
1
KIWAG-SWX_A3q
Das
Urh
eber
rech
t an
dies
er Z
eich
nung
, die
dem
Em
pfän
ger
pers
önlic
h an
vertr
aut w
ird, v
erbl
eibt
uns
erer
Firm
a.O
hne
unse
re s
chrif
tlich
e G
eneh
mig
ung
darf
die
Zeic
hnun
gw
eder
kop
iert
noch
ver
viel
fälti
gt, n
och
an D
rittp
erso
nen
mitg
etei
lt od
er z
ugän
glic
h ge
mac
ht w
erde
n.
interne und externe Fertigung
28.06.2016
siehe TabelleBl. Ver.
Material-Nr.
Zeichnungs-Nr. 100.247.71527.06.2016 Keb27.06.2016 Keb
Keb30.10.2015
ges.
gepr.
gez.
100012154Kopie DatumErsatz für MassstabDatumÄnderung
Werkstoff
Erste Proj.-Nr.
Erstmals verwendet
measure. analyze. innovate.
1:5
1 / 1 aA3
BG4 CADENAS MasszeichnungDM-Sensor 4503B 200-1K CADENAS
Dimensions size 4 in mm Dimensions for mounting base (GU)
= Option mounting base "GU"M = Measuring end
Fig. 3: Type 4503B... size 4All dimensions without tolerances comply with ISO 2768-mH
Werkstückkanten nach ISO 13715
-0,2 +0,25
Allgemeintoleranzen
Längenmasse
Abmasse Winkelmasse kürz. Schenkel Abmasse
...10±0°20'
* ...0,5
> 10...50
>0,5...3 >120...400 >400..1000
±0°30'>400...
±0,1 ±0,5> 3...6 > 30...120
> 50...120±0,3
±1°
±0,2 ±0,8
±0°10'>120...400
*=KISTLER-Norm
±0,1±0,05> 6...30
±0° 5'
ISO 2768-mH
10
5
97 ±0,2
46
±0,1
117 ±0,2
10
137
A
A
60
+ +0,03
0,01
M8
4x
10
46 ±0,025
11
5
A-A
KIWAG-SWX_A3q / Vers. 21-Sep-2017
Das
Urh
eber
rech
t an
dies
er Z
eich
nung
, die
dem
Em
pfän
ger
pers
önlic
h an
vertr
aut w
ird, v
erbl
eibt
uns
erer
Firm
a.O
hne
unse
re s
chrif
tlich
e G
eneh
mig
ung
darf
die
Zeic
hnun
gw
eder
kop
iert
noch
ver
viel
fälti
gt, n
och
an D
rittp
erso
nen
mitg
etei
lt od
er z
ugän
glic
h ge
mac
ht w
erde
n.
interne und externe Fertigung
siehe Tabelle
3.23154503B
Bl. Ver.
Material-Nr.
Zeichnungs-Nr. 100.421.465
Rou03.06.2019
ges.
gepr.
gez.
Kopie DatumErsatz für MassstabDatumÄnderung
Werkstoff
Erste Proj.-Nr.
Erstmals verwendet
measure. analyze. innovate.
1:2
1 / 1 0A3
Anschlussmaße GU 4503B200-1K
Size 4
Rated torque N∙m 200 / 500 / 1 000
L 267L1 61L2 61øD 98
ød g6 42A 90B 65C 15E 32G 137H 78,5
øTk 87M M6 (4x90 °)T 12 deep Connecting dimensions for mounting base Size 4
N∙m Tightening torque200
25 N·m (strength class of the screw: 8.8)500
1 000
All dimensions without tolerances comply with ISO 2768-mH
Page 8/12
Torque sensor – with dual-range-option, Type 4503B...45
03B_
000-
767e
-08.
20
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Dimensions Type 4503B..., Measuring ranges 2 000 / 5 000
Werkstückkanten nach ISO 13715
-0,2 +0,25
Allgemeintoleranzen
Längenmasse
Abmasse Winkelmasse kürz. Schenkel Abmasse
...10±0°20'
* ...0,5
> 10...50
>0,5...3 >120...400 >400..1000
±0°30'>400...
±0,1 ±0,5> 3...6 > 30...120
> 50...120±0,3
±1°
±0,2 ±0,8
±0°10'>120...400
*=KISTLER-Norm
±0,1±0,05> 6...30
±0° 5'
ISO 2768-mH
d
g6
d
g6
L2 L1
90 A
25 25
H
L
5
E E 164
B
G
M
1
38
150
Tk
160
±0,1
5
10 H7
4,1
150
60
C
100
13
D
71
180
M T(4x 90° = 360°)
Messseite
Option Zubehör Gehäuseunterbau "GU"
M
1
KIWAG-SWX_A3q
Das
Urh
eber
rech
t an
dies
er Z
eich
nung
, die
dem
Em
pfän
ger
pers
önlic
h an
vertr
aut w
ird, v
erbl
eibt
uns
erer
Firm
a.O
hne
unse
re s
chrif
tlich
e G
eneh
mig
ung
darf
die
Zeic
hnun
gw
eder
kop
iert
noch
ver
viel
fälti
gt, n
och
an D
rittp
erso
nen
mitg
etei
lt od
er z
ugän
glic
h ge
mac
ht w
erde
n.
interne und externe Fertigung
28.06.2016
siehe TabelleBl. Ver.
Material-Nr.
Zeichnungs-Nr. 100.242.44427.06.2016 Keb27.06.2016 Keb
Keb13.08.2015
ges.
gepr.
gez.
100012154Kopie DatumErsatz für MassstabDatumÄnderung
Werkstoff
Erste Proj.-Nr.
Erstmals verwendet
measure. analyze. innovate.
1:2
1 / 1 aA3
BG5 CADENAS MasszeichnungDM-Sensor 4503B2K_5K CADENAS
Dimensions size 5 in mm Dimensions for mounting base (GU)
= Option mounting base "GU"M = Measuring end
Fig. 4: Type 4503B... Size 5All dimensions without tolerances comply with ISO 2768-mH
Werkstückkanten nach ISO 13715
-0,2 +0,25
Allgemeintoleranzen
Längenmasse
Abmasse Winkelmasse kürz. Schenkel Abmasse
...10±0°20'
* ...0,5
> 10...50
>0,5...3 >120...400 >400..1000
±0°30'>400...
±0,1 ±0,5> 3...6 > 30...120
> 50...120±0,3
±1°
±0,2 ±0,8
±0°10'>120...400
*=KISTLER-Norm
±0,1±0,05> 6...30
±0° 5'
ISO 2768-mH
93,5 ±0,2
40
±0,1
15
0
144 ±0,2
169
5
A
A
M8
4x
10
60
+ +0,03
0,01
18
0
69 ±0,025
A-A
KIWAG-SWX_A3q / Vers. 21-Sep-2017
Das
Urh
eber
rech
t an
dies
er Z
eich
nung
, die
dem
Em
pfän
ger
pers
önlic
h an
vertr
aut w
ird, v
erbl
eibt
uns
erer
Firm
a.O
hne
unse
re s
chrif
tlich
e G
eneh
mig
ung
darf
die
Zeic
hnun
gw
eder
kop
iert
noch
ver
viel
fälti
gt, n
och
an D
rittp
erso
nen
mitg
etei
lt od
er z
ugän
glic
h ge
mac
ht w
erde
n.
interne und externe Fertigung
siehe Tabelle
3.23154503B
Bl. Ver.
Material-Nr.
Zeichnungs-Nr. 100.421.471
Rou03.06.2019
ges.
gepr.
gez.
Kopie DatumErsatz für MassstabDatumÄnderung
Werkstoff
Erste Proj.-Nr.
Erstmals verwendet
measure. analyze. innovate.
1:2
1 / 1 0A3
Anschlussmasse f. GU 4503B2K-5K
Size 5
Rated torque N∙m 2 000 / 5 000
L 418L1 120L2 120øD 143
ød g6 70A 159,5B 124,5C 20E 47G 169H 97
øTk 132M M8 (4x90 °)T 16 deep
Connecting dimensions for mounting base Size 5
N∙m Tightening torque
2 000 25 N·m (strength class of the screw: 8.8)5 000
All dimensions without tolerances comply with ISO 2768-mH
Page 9/12
Torque sensor – with dual-range-option, Type 4503B...45
03B_
000-
767e
-08.
20
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Dimensions feather key groove acc. to DIN 6885-1 (option P1)
Dimensions in mm
Werkstückkanten nach ISO 13715
-0,2 +0,25
Allgemeintoleranzen
Längenmasse
Abmasse Winkelmasse kürz. Schenkel Abmasse
...10±0°20'
* ...0,5
> 10...50
>0,5...3 >120...400 >400..1000
±0°30'>400...
±0,1 ±0,5> 3...6 > 30...120
> 50...120±0,3
±1°
±0,2 ±0,8
±0°10'>120...400
*=KISTLER-Norm
±0,1±0,05> 6...30
±0° 5'
ISO 2768-mH
d
l
b
t1
Abmessungen Passfedernut 4503B PS BG
A4 01 / 1
2:1
measure. analyze. innovate.
Erstmals verwendet
Erste Proj.-Nr.
Werkstoff
Änderung Datum MassstabErsatz für Kopie Datum
gez.
gepr.
ges.
29.05.2019 Rou
100.421.367Zeichnungs-Nr.
Material-Nr.
KIWAG-SWX_A4h / Vers. 21-Sep-2017
Ver.Bl.
4503B
18030439 4503B
interne und externe Fertigung
Das
Urh
eber
rech
t an
dies
er Z
eich
nung
, die
dem
Em
pfän
ger
pers
önlic
h an
vertr
aut w
ird, v
erbl
eibt
uns
erer
Firm
a.O
hne
unse
re s
chrif
tlich
e G
eneh
mig
ung
darf
die
Zeic
hnun
gw
eder
kop
iert
noch
ver
viel
fälti
gt, n
och
an D
rittp
erso
nen
mitg
etei
lt od
er z
ugän
glic
h ge
mac
ht w
erde
n.
Feather key according to DIN 6885-1
Size 1 2 3 4 5
Rated torque N∙m 0,2 0,5 1 2 / 5 10 / 20 50 / 100 200 / 500 / 1 000 2 000 / 5 000
ødg6 mm 9 10 12 22 42 70
bP9 mm 3 3 4 6 12 20t1 mm 1,8+0,1 1,8+0,1 2,5+0,1 3,5+0,1 5+0,2 7,5+0,2
l mm 12+0,2 14+0,2 16+0,2 22+0,2 50+0,3 110+0,3
Page 10/12
Torque sensor – with dual-range-option, Type 4503B...45
03B_
000-
767e
-08.
20
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Torsion shaft Strain gauge - full bridge
Torque
Speed
11 ... 30 VDC
0 V
0 ... ±5/10 V0 V
Track A/B/Z up to 8 192 pulses/revolution0 V
Measuring electronics
MMeasuring end
ADrive end
12 500 1/min
3,19 N·m
Serial interface torque
Measuring range selection
Standardized andcalibrated outputs:
Type 4700B... CoMo Torque Evaluation Instrument for Torque Sensors
Control
Acknowledgment measuring range
Principle of function
Mounting torque sensor Type 4503B... between drive and brake
Mounting torque sensor Type 4503B... with holding bracket (GU) or housing base
Drive (specimen)
Drive (specimen)
Full couplings
Half coupling
Sensor
Sensor
Housing base (GU) or holding bracket
Twist protection (should avoid heavy tension-forces on the torque sensor
Full couplings
Half coupling
Brake
Brake
Fig. 5: Installation without holding bracket or housing base (GU).
Fig. 6: Installation with holding brack-et or housing base (GU).
Page 11/12
Torque sensor – with dual-range-option, Type 4503B...45
03B_
000-
767e
-08.
20
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Function PIN Description
Measuring range selection 1 Amplification Normal (1:1) with 0 ... 2 VDCExtended (1:x) with 3,5 ... 30 VDC
100 % control input 4 Control Off: 0 ... 2 VDCOn: 3,5 ... 30 VDC
7 OGND Opto isolated ground for measuring range selection and control input
RS-232C interface 5 TXD Serial send path of the torque sensor6 RXD Serial receive path of the torque sensor3 DGND Ground relating the RS-232C interface
Scaling selector switchAcknowledgment output
2 ACK 0 VDC at normal (1:1)24 VDC at (1:x)
Electrical connections
Pin allocation of the 12 Pin built-in standard connector
Pin allocation of the 7 Pin built-in connector for range switch
Shielded measuring cable
DVM
F
A
C
D
H
E
K M
Supply 11 … 30 VDC
Torque output
Speed/angle output
Contol signal input Control button
+5 V TTL (Track A)
DGND (0 V)
+U B
Ground U B
±5 V
AGND (0 V)
3,5 ... 30 V Shield
Supply and evaluation unit
=
~
G+5 V TTL (Track B)J+5 V TTL (Track Z)
Torque sensorType 4503B...
Counter
Measuring range acknowledgment
Control signal input
Control button *
3,5 ... 30 V
+U b
4
7
1
Range selection switch
Measuring range selection 3,5 ... 30 V
OGND (0 V)
PC
RS-232C interface
DGND (0 V)
5
RXD
TXD
ACK
6
3
RXD
TXD
GND
Shielded measuring cable
2
Supply and evaluation unit
Torque sensorType 4503A...
Fig. 5: Connection diagram of 12 pin built-in connector (standard) Fig. 6: Connection diagram of 7 pin built-in connector
Function PIN Description
Supply voltage F +UB 11 ... 30 VDC, power consumption <10 WA GND Ground relating to +UB
Shield M In sensor connected to housingTorque output C UA Voltage output
±5/10 VDC at ±Mnom at >10 kΩ5/10 VDC at control signal activation
Frequency outputFA Frequency output >2 kΩ100 kHz ± 40 kHz
D AGND Ground relating to UA Ground relating to FA
Speed-/angle of rotati-
on pulses
H Track A Active, TTL levelG Track B Active, TTL level, 90 ° displaced only option H, WJ Track Z Active, TTL level, reference pulse only option H, W
100 % control input K Control Off: 0 ... 2 VDCOn: 3,5 ... 30 VDCRi,K = 10 kΩ
RS-232C interface (CoMo Torque)
B TXD Digital send path to the CoMo TorqueL RXD Digital receive path
Digital ground po-tential
E DGND Ground relating to speed- or angle of rotation pulses, control input, digital connection to RS-232C
1
34
5
67
2
UB GND (A) and AGND (D) must not be connected (electronics can be damaged).It is recommended to use a differential amplifier inputfor the output UA/AGND.
Page 12/12
Torque sensor – with dual-range-option, Type 4503B...45
03B_
000-
767e
-08.
20
This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded.
©2015 ... 2020, Kistler Group, Eulachstrasse 22, 8408 Winterthur, SwitzerlandTel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.comKistler is a registered trademark of Kistler Holding AG.
Included accessories Type/Art. No.• USB Cable 55115378
Optional accessories Type/Art. No.• Mounting base "GU", for measuring 18030861
ranges 0,2 ... 20 N∙m• Mounting base "GU", for measuring 18030862
ranges 50 ... 100 N∙m• Mounting base "GU", for measuring 18030863
ranges 200 ... 1 000 N∙m• Mounting base "GU", for measuring 18030864
ranges 2 000 ... 5 000 N∙m• Female connector with solder eye 12 pin 18008371• Female connector with solder eye 7 pin 18008363• Connection cable, 5 m, 12 pin 18008935• Connection cable, 5 m, 12 pin – open ends 18008943• Connection cable, 5 m, 7 pin – open ends 18008996• Connection cable 2,5 m,
12 pin – CoMo Torque 18008967• Connection cable 5 m,
RS-232C 7 pin/D-Sub 9 pin 18008994• ControlMonitor CoMo Torque
Evaluation instument for torque sensors 4700B...
Cable according to the data sheet 000-615.
Order example:
Type 4503B050LP000KA0
Torque sensor with 1 measuring range: rated torque 50 N∙m: 050,
version L: max. speed 12 000 min-1, without feather key groove :
P0, Standard output signal ±5 VDC and frequency 100 ±40 kHz: 00,
calibration WKS1 single range: KA0
Measuring ranges in N∙m
0,2 0,2
0,5 0,5
1 001
2 002
5 005
10 010
20 020
50 050
100 100
200 200
500 500
1 000 1K0
2 000 2K0
5 000 5K0
Pulses per revolution
Low speed 60 L
High speed up to 2 x 8 192 + Z H
Low speed up to 2 x 8 192 + Z W
Feather key groove
Without P0
With P1
Output signal
Voltage ±5 VDC and
Frequency 100 ±40 kHz 00
Voltage ±10 VDC and
Frequency 100 ±40 kHz B1
Calibration
WKS 1 − single range KA0
WKS 1 − dual range 1:1 and 1:10 KA1
WKS 1 − dual range 1:1 and 1:5 KA2
WKS 2 − single range WA0
WKS 2 − dual range 1:1and 1:10 WA1
WKS 2 − dual range 1:1 and 1:5 WA2
DAkkS 5 − single range,
5 measuring point DK5
DAkkS 8 − single range,
8 measuring point DK8
DAkkS 5 − dual range,
5 measuring point 1:1 and 1:10 D51
DAkkS 5 − dual range,
5 measuring point 1:1 and 1:5 D52
DAkkS 8 − dual range,
8 measuring point 1:1 and 1:10 D81
DAkkS 8 − dual range,
8 measuring point 1:1 and 1:5 D82
Ordering key Type 4503B
Definition of calibration terms:• WKS 1: Works calibration at 5 points right, 3 points left • WKS 2: Works calibration at 5 points right and left, and
repeat series • DAkkS: Calibration per DIN 51309
Our calibration service D-K-15127-02-00 provides traceable calibrations for torque sensors from all manufacturers.