TOTAL SYSTEM SOLUTIONS PRICE LIST - Americas › media › 634811 ›...

2016PRICE LIST

TOTAL SYSTEM SOLUTIONS

Effective February 1, 2016

Submersible Pumping Systems 1Submersible Turbine Pumps 1

Variable Speed Submersible Turbine Pumps 1

Intelligent Submersible Turbine Pumps 3

Fixed Speed Submersible Turbine Pumps 5

2 hp 5

1½ hp 8

1/3 and 3/4 hp 11

Advanced Protection 14

Fixed Length 17

Mechanical Line Leak Detectors 20

Submersible Turbine Pump Controllers 21

Single-Phase Smart Controller 21

Dispenser Hook Isolation 21

Single-Phase Control Box 22

Submersible Turbine Pump Accessories 23

Submersible Turbine Pump Repair Parts 24

High Capacity Submersible Pumps 29

High Capacity Pump 29

High Capacity Leak Detectors 31

High Capacity Pump Controllers 32

Three-Phase Smart Controller 32

STP-CB 3/5 Magnetic Starter 32

High Capacity Pump Repair Parts 33

Diesel Exhaust Fluid Pump Motor Assemblies 36

Variable Length DEF STP Kits 36

Fixed Length DEF STP Kits 37

Service Station Hardware 38Underground Storage Tank Equipment 38

300 Vapor Check Valve Adapter 38

304 4" Vapor Recovery Cap 38

306 4" Coaxial Vapor Recovery Adapter 38

308 Ball Float Vent Valves 39

300 Series Extractor Vent Valves 39

Extractor Vent Valve Accessories 40

362 Vapor Shear Valve 40

662 Emergency Shut-off Valves 40

Emergency Shut-off Valve Accessories 41

Emergency Shut-off Valve Replacement Tops 41

775 4" Side Seal Fill Cap 41

776 4" Side Seal Fill Adapter 41

777 4" Top Seal Fill Caps 42

778 Top Seal Fill Pipe Adapters 42

SWF-100-B Top Seal Swivel Fill Pipe Adapters 42

SWV-101-B Vapor Swivel Adapters 42

779 3" Top Seal Fill Caps 43

Autolimiter® Automatic Shut-off Valve 43

Remote Fill Kit 43

782 Drop Tubes 43

Probe Cap and Adapter Kit 43

Tank Bottom Protectors 43

PV-Zero 43

Spill Containers 44

Defender Series™ Spill Containers 44

Defender Series™ Overfill Prevention Valve 48

Phil-Tite Spill Container Replacement Parts 52

702, 703, 705, 715 and 725 Grade Level Spill Containers 52

Grade Level Spill Container Accessories and Replacement Parts

52

702, 705, 715 and 725 Below Grade Level Spill Containers 54

Manways 55

7-1/2", 12" and 18" Round Manways 55

Steel Manways 55

16" and 24" Square Manways with Knock-Down Skirts 56

12", 30", 36" and 42" Fiber Reinforced Composite Manways 57

Composite Access Covers 59

Composite Manhole Lids 59

Monitoring Test Well Manways 61

Monitoring Test Well Accessories 61

787 Series Fuel Identification 62

Multi-port Containment 63

Defender Series™ Multiport Manways 63

Dual Point Fill Watertight Multiport Sump Packages 66

Dual Point Fill Watertight Multiport Sump Package Accessories

67

Flexible Connectors 68

Pipe Guards & Bollards 71

Remote Fill Boxes 71

Aboveground Storage Tank Equipment 72

605, 606, 616 and 636 Anti Syphon Valves 72

664 Pressure Regulator Valve 72

706 AST Spill Container 72

709 Warden® Aboveground Storage Tank OPV 72

Fill Caps 72

800 Tank Vents 73

802 Pressure Vacuum Vents 73

803 Aboveground Emergency Vents 73

Suction System Equipment 74

50-201 Brass Foot Valves 74

320 Foot Valve Extractor 74

325 Product Line Isolation Valve 74

515 and 516 Brass Vertical Check Valves 74

615 and 635 Angle Check Valves 74

621 and 622 Under Pump/In-Line Check Valves 75

650 Union Check Valve 75

Installation Tools 76

Wrenches 76

Flaring Tool 76

Spill Container Tool Kit 76

Accessories 77

Debris Buckets 77

M/F 4×4 77

Alignment Brackets 77

Cover Removal Tool 77

Replacement Parts 78

Underground Storage Tank Equipment 78

Spill Containers 78

Manways 80

Fiberglass 80

Aboveground Storage Tank Equipment 81

Suction Systems 81

Tools 81

Piping & Containment Systems 82XP Piping 82

XP Pressure and Suction Product Piping 82

XP Marina/Aboveground Product Piping 83

4" Ducting 83

XP Fittings 84

XP Clamshell Swivel Pipe Fittings 84

XP Male Swage Swivel Pipe Fittings 84

XP Clamshell Non-Swivel Pipe Fittings 84

XP Clamshell Non-Swivel Tee and Elbow Fittings 84

Quick Release XP Fittings 85

End Connections and Fittings 85

Entry Boots 88

Flexible Entry Boots 88

Flexible Double Entry Boots 89

Flexible Bulkhead Boots 89

MD-Series Flexible Entry Boots 89

Rigid Entry Boots 90

Rigid Entry Boots for Electrical Conduit 90

Fusion Entry Boots 90

Split Test Boots 91

Clamshell Secondary Test Boots 91

Transition Sleeves 92

Grade Level Transition Sleeve™ 92

Wall Transition Sleeve 92

Sumps 93

Below Grade Transition Tank Sumps 93

Below Grade Intermediate Piping Sumps 93

Grade Level Transition Sump 93

4542 Series One-Piece Tank Sumps 93

4736 Series One-Piece Tank Sumps 93

Watertight Fiberglass Turbine Sump Packages 94

Large Mouth Poly Dispenser Sumps 96

Single and Double Wall Fiberglass Large Mouth Sumps 97

Classic Dispenser Pan Sumps 98

Sump Accessories 99

Tank Fitting Adapters 99

Tank Manway Adapters 99

Stabilizer Bar Kits 99

Accessories 100

Installation Tools 100

Swage Machine 100

UPP Semi-Rigid Pipework Systems 101

UPP Dispenser Sumps 106

UPP Installation Tools 107

Dispensing Systems 1109961 Clean Air Separator 110

Stage II Vapor Recovery Dispenser Mounted Vacuum Sources

111

VP1000 111

VP1000 Replacement Parts 113

VP1200 Series Self-Contained Suction Pump Dispenser-Mounted Vacuum Source

114

Stage II Vapor Recovery Nozzles 115

400 Series ORVR Nozzle 115

600 Series Bootless Nozzle 115




900 Series EVR Certified Nozzle 117

Hoses and System Accessories 119

Standard Healy and Whip Hoses 120

Metric- Ready Hoses 120

Balance-Ready Hoses 121

Hose Adapters, Breakaways, Kits and Spare Parts 122

Low Permeation Vapor Recovery Hose 124

Healy FLEXSTEEL FUTURA Vapor Assist Hose 125

Stage II Vapor Recovery Central Vacuum Sources 126

9000 Series Mini-Jet Central Vacuum Pump 126

VP500 Central Vacuum Vane Pump 126

100 Jet Pump Central Vacuum Source 126

System Test Equipment 127

FLEX-ING & EBW Swivels, Breakaways and Accessories 128

¾" Products 128

1" Products 128

1¼" Products 128

1½" Products 129

Hose Retriever System 129

495 Utility Nozzle Replacement Parts 129

Nozzle Accessories 130

Diesel Exhaust Fluid Hanging Hardware 131

DEF Nozzles 131

DEF Break Aways 131

Hardwall Hose 132

Softwall Hose 133

Specialty Hose 134

FLEX-ON™ Marina Hose 134

FLEX-COLD Cold Weather Hose 135

AGRI-FLEX Farm Hose 136

Ethanol Hose 137

DEF Hoses 138

Low Permeation Hose 139

Service Station Air Hose 140

Fuel Management Systems 141

Fuel Management System Consoles 142

TS-550 evo Fuel Management System 142

TS-5 Fuel Management System 142

TS-550 and TS-5000 Fuel Management Systems 143

Fuel Management System Console Accessories 144

Tank Monitors & Environmental Monitoring 147

Colibri Tank Monitor 147

TS-EMS Environmental Monitoring System 148

In-Station Diagnostics 149

Tank Sentinel® Consoles 150

TS-1001Console 150

TS-1001/G Console 151

TS-750 Console 152

Tank Sentinel® Console Accessories 153

S940 Sensor Alarm Console 154

Electronic Line Leak Detectors 155

TS-L300 AutoLearn™ 155

Line Sentinel™ 155

Leak Detection Probes 156

Leak Detection and Inventory Control Probes 156

Moorman Level Gauge Kit 157

Flex Probes 157

Float Kits 159

Phase Separation Float Kits 159

Density Measurement Float Kits 159

Probe Installation Kits 160

TSP-HIS Hydrostatic Interstitial Sensor 161

TSP-DIS Discriminating Interstitial Sensor 161

TSP-EIS Electro-Optic Interstitial Sensor 161

TSP-HFS Horizontal Float Switch Liquid Sensor 162

TSP-ULS Liquid Sensor 162

TSP-UHS Universal Hydrostatic Sensor 162

TSP-DMS Discriminating Magnetostrictive Sensor 162

TSP-DDS Discriminating Dispenser Sump Sensor 162

TSP-DTS Discriminating Turbine Sump Sensor 162

TSP-DVS Discriminating Vapor Sensor 162

TSP-MWS Monitoring Well Sensor 163

TSP-HLS Level Sensor 163

DC400 Dispensing Cutoff System 163

Sensor Installation Kits 163

Sensor Installation Accessories 163

External Console Hardware 165

TS-RA1 Remote Audible and Visible Alarm Unit 165

TS-RA2 Remote Audible and Visible Alarm Unit 165

TS-RK Remote Alarm Acknowledge Unit 165

TS-DIM Dispenser Interface Module 165

TS-TPI Turbine Pump Interface 165

TS-ROM2 BriteBox™ Relay Output Module 165

TS-EPS Ethernet Port Server 165

Software 166

System Sentinel Site Licenses 166

System Sentinel Tech Edition 166

System Sentinel AnyWare Site Licenses 166

Get Connected AnyWare 167

Accessories 168

TS-STS Sump Test Kit 168

Spare Parts 168

T5 Series and TS-EMS Consoles 168

Colibri 169

TS-504 and TS-750 170

TS-508 170

TS-1001 170

TS-2001 171

TS-LLD 171

TS-LS300 172

TS-LS500 172

TS-STS Sump Test Kit 172

Accessories 173

Transport Systems 174

Fuel and Vapor Transfer Solutions 174

API Bottom Loading Adapters 174

API Bottom Loading Adapter Spare Parts 175

Dust Cap 175

Air Interlock Valves 176

Three-Way Air Valves 176

Six-Way Air Valves 176

Air Interlock with Limit Switch 177

Gravity Drop Adapters 178

Female Gravity Drop Adapters 178

Male Gravity Drop Adapters 178

Vapor Check Valves 179

Threaded Vapor Check Valve 179

Flanged Vapor Check Valve 179

Vapor Caps 180

Vapor Return Hose Couplers 181

Air-Operated Sequential Vapor Valves 182

Hose Tube Doors 183

Product Drop Elbows 184

Dual Point Vapor Recovery Elbow 186

Coaxial Delivery Elbow 186

Attachments 187

Gasket Kit 187

Sight Glass Kit 187

3" Cam and Groove Adapter 187

4" Cam and Groove Adapter 187

3" NPT Male Adapter 187

4" NPT Male Adapter 187

Cam and Groove Adapters 187

Emergency Valves 188

Mechanically Operated 90 Degree (Victaulic) 188

Mechanically Operated 90 Degree (Flanged) 188

Air Assisted 90 Degree (Victaulic) 189

Air Assisted 90 Degree (Flanged) 189

3" Emergency Valve 190

Side Seal Adapter 191

Bulk Pneumatic Pressure Relief Valves 191

Optic Control System 192

OCS Overfill Protection Solutions 192

Two-Wire Controller 192

Two-Wire Optic Overfill Probes 192

Two-Wire Optic Retained Product Probes 192

OCS Probe Solutions 192

Probe Holder Solutions 192

Probe Holders 192

Single Socket Solutions 192

Installation Kits 192

Wiring Kits 193

Variable Speed Submersible Turbine Pump Model Designation SystemA typical turbine model designation has up to five components to define the pump being supplied as follows:STP XXXXX Y-A-B

STP = Basic Model Designation

XXXXX = Factory Installed Options

STP model designations may include one or more of the following characters in alphabetical order:

F = Floating suction adapter (1 1/2" NPT female adapter)

K = Intake filter screen (IFS, factory installed to PMA)

M = Magshell™ (flow enhancing, expanded PMA shell)

* R = Model R check valve (24 psi relief/22 psi reset for PLLD)

* W = Model W check valve (16 psi relief/13 psi reset for PPM4000)

Y = Pump Motor Horsepower RatingVS2 = 2 hp variable speed

VS4 = 4 hp variable speedA = Model Length

VL1 = Variable length range #1



Note: VL2 models fit 94% of all known installationB = Riser Pipe Length

Riser pipe length is expressed as two numeric characters that indicate the total length of the riser in inches. Riser pipes are available from 7" to 60" in 1" increments (additional charge for risers 31" or longer).

* Note: If not otherwise specified, all STP models are supplied with standard model check valve (40 psi relief/35 psi reset for MLD, TS-LS300, and TS-LS500).

Note: Standard models up to 10% ethanol capable.

1

Model Description Range Length

Model Length *

Without Riser With Riser

STPMVS2-VL1 2 hp variable speed with MagShell™ VL1 59"-87" $1,644.00 $1,694.00






Notes:1. Remove “M” from model number for non-MagShell™ pump motor assembly.

Model ListF $125.00

K $165.00

R no adder

W no adder

Model List5874202800 $1,081.00

400137908 $61.00

402459931 $129.00

402507930 $151.00

5800300100 $359.00

Model List400693901 $1,967.00400693907 $1,967.00402671901 $2,417.00402671907 $2,417.00

* Model length (A) defined as the dimension from turbine manifold bottom to pump motor inlet.

Factory Installed Options (specified in model number at time of STP order)Description

Floating suction adapter, 1½" NPT female, must be factory installed

Variable Speed Submersible Turbine Pumps (variable speed, variable length)

2. All above models are listed for fuel mixtures containing up to 10% ethanol with gasoline, diesel fuels, and 20% MTBE, 20% ETBE or 17% TAME with gasoline.

3. All models are supplied with a standard check valve unless factory option “R” or “W” is specified.

4. All above models can only be powered by a MagVFC™. 4 hp models require three-phase incoming power supply, 2 hp models can be supplied with single- or three-phase incoming power.

5. 4" riser pipe, if supplied locally, must be 4½" OD by 3/16" WT tubing.

6. For riser pipe lengths 31" to 60", $50.00 adder charge applies.

IFS (intake filter screen) factory assembled to pump motor assemblyModel R check valve, factory installed, for Veeder-Root ™ PLLD Line Leak

Model W check valve, factory inst., for Red Jacket™ PPM4000 Line Leak

Field Installed Options (intelligent submersible turbine pump specific accessories)Description

Veeder-Root™ is a trademark of Danaher Corporation. Red Jacket™ is a trademark of Veeder-Root Company.

Description

Kit with 4 hp variable speed non-MagShell™ (PMA VS4)

Note: Kits include variable speed pump motor assembly, MagVFC™ variable frequency controller, four-wire contractor’s plug and installation instructions.

MagVFC™, 2 hp or 4 hp variable frequency controller, one required per STP

Syphon check valve, alcohol-gasoline compatible (when ordered with STP)

Model 65 psi check valve (for slave of manifolded STPs with Veeder-Root™ PLLD)

STP-DHI, dispenser hook isolation for 110 Volt dispenser handle switches, up to eight each

Variable Speed Conversion Kits

Secondary syphon kit (when two syphon primes are required for one STP)

Kit with 4 hp variable speed with MagShell™ (PMA MVS4)

Kit with 2 hp variable speed non-MagShell™ (PMA VS2)

Kit with 2 hp variable speed with MagShell™ (PMA MVS2)

2

Intelligent Submersible Turbine Pump Model Designation SystemA typical turbine model designation has up to five components to define the pump being supplied as follows:IST XXXXX Y-A-B

IST model designations may include one or more of the following characters in alphabetical order:

VS4 = 4 hp variable speed

A = Model Length

B = Riser Pipe Length

IST = Basic Model Designation



Note: All IST models include alcohol-gasoline compatibility (up to 85% ethanol, up to 20% biodiesel, or 100% biodiesel), variable speed and variable length as part of the base model.





Y = Pump Motor Horsepower Rating**


Note: IST-2 and ISTVS4-VL2 models fit 94% of all known installations


** Note: If not otherwise specified, 2 hp variable speed is implied.

1 = 2 hp variable length, 59"-87"



VL1 = 4 hp variable length, 64"-92"



3

Model Description Model Length * Without Riser With Riser

ISTM-1 2 hp variable speed with MagShell™ 59"-87" $2,039.00 $2,089.00



ISTMVS4-VL1 4 hp variable speed with MagShell™ 64"-92" $2,539.00 $2,589.00







Model ListF $125.00

K $165.00

R no adder

W no adder

Model List5874202800 $1,081.00400137908 $61.00

402459931 $129.00

402507930 $151.00

5800300100 $359.00

Model List400693905 $2,197.00

400693906 $2,197.00

402671905 $2,647.00

402671906 $2,647.00

Secondary syphon kit (when two syphon primes are required for one IST)

Syphon check valve, alcohol-gasoline compatible (when ordered with IST)

Model 65 psi check valve (for slave of manifolded ISTs with Veeder-Root™ PLLD)

Model R check valve, factory installed, for Veeder-Root ™ PLLD Line Leak

Intelligent Submersible Turbine Pumps (variable speed, variable length, AG compatible)



IFS (intake filter screen) factory assembled to pump motor assembly



Kit with AG compatible 4 hp variable speed with MagShell™ (PMAAGMVS4)

Note: Kits include variable speed pump motor assembly, MagVFC™ variable frequency controller, four-wire contractor’s plug and installation instructions.

2. All above models are listed for compatibility with fuel mixtures containing diesel fuels with up to 20% biodiesel, 100% biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline.

4. All above models can only be powered by a MagVFC™. 4 hp models require three-phase incoming power supply, 2 hp models can be supplied with single- or three-phase incoming power.


Variable Speed Conversion Kits (AG compatible)Description

Kit with AG compatible 2 hp variable speed non-MagShell™ (PMAAGVS2)

Kit with AG compatible 2 hp variable speed with MagShell™ (PMAAGMVS2)

Kit with AG compatible 4 hp variable speed non-MagShell™ (PMAAGVS4)

Model W check valve, factory installed, for Red Jacket™ PPM4000 Line Leak

Field Installed Options (intelligent submersible turbine pump specific accessories)Description

MagVFC™, 2 hp or 4 hp variable frequency controller, one required per IST

4

2 hp Fixed Speed Submersible Turbine Pump Model Designation SystemA typical turbine model designation has up to five components to define the pump being supplied as follows:STP XXXXX Y-A-B


200 = 2 hp fixed speedA = Model Length





AG = Alcohol-gasoline compatible (up to 85% ethanol, up to 20% biodiesel, or 100% biodiesel)




H = High pressure (45 psi deadhead output)




Y = Pump Motor Horsepower Rating





Note: VL2 models fit 94% of all known installation

5


Model Length *


STPM200-VL1 2 hp fixed speed with MagShell™ VL1 63"-91" $2,395.00 $2,445.00



STPHM200-VL1 2 hp high pressure fixed speed with MagShell™ VL1 63"-92" $2,455.00 $2,505.00



STPAGM200-VL1 2 hp AG fixed speed with MagShell™ VL1 63"-91" $2,790.00 $2,840.00



STPAGHM200-VL1 2 hp AG high pressure fixed speed with MagShell™ VL1 63"-92" $2,850.00 $2,900.00



Notes:

1. Remove “M” from model number for non-MagShell™ pump motor assembly.


4. All above models require single-phase, 208-230 VAC, 60 Hz incoming power.



Model ListF $125.00

K $165.00

R no adder

W no adder

2 HP Fixed Speed Submersible Turbine Pumps


2. STP models are listed for compatibility with fuel mixtures containing up to 10% ethanol with gasoline, diesel fuels, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. STPAG models are listed for compatibility with fuel mixtures containing diesel fuel with up to 20% biodiesel, 100% biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline.



IFS (intake filter screen), factory assembled to pump motor assembly

Model R check valve, factory installed, for Veeder-Root™ PLLD Line Leak

Model W check valve, factory inst., for Red Jacket™ PPM4000 Line LeakVeeder-Root™ is a trademark of Danaher Corporation. Red Jacket™ is a trademark of Veeder-Root Company.

6

Model List400137908 $61.00

400818921 $141.00

402312921 $599.00

402312921 $734.00

402313921 $474.00

402459931 $129.00

402507930 $151.00

5800100215 $409.00

5800100215 $269.00

5800300100 $359.00

Veeder-Root™ is a trademark of Danaher Corporation.

STP-SCI, single-phase smart controller (when purchased without a 4" STP)

STP-SCI, single-phase smart controller (when purchased with a 4" STP) *


* When purchasing STP-SCI or STP-DHI-SCI in equal quantities of fixed speed 4" STPs



STP-DHI-SCI, combo DHI with factory wired STP-SCI (when purchased without a 4" STP)

STP-DHI-CBS, combo DHI with factory wired STP-CBS

Syphon check valve (when ordered with STP)

STP-CBS, single-phase control box with lockout switch, 110 Volt coil

STP-DHI-SCI, combo DHI with factory wired STP-SCI (when purchased with a 4" STP) *

Field Installed Options (2 hp fixed speed specific accessories)Description

7

1 1/2 hp Fixed Speed Submersible Turbine Pump Model Designation SystemA typical turbine model designation has up to five components to define the pump being supplied as follows:STP XXXXX Y-A-B


150 = 1 1/2 hp fixed speedA = Model Length
















H = High pressure (45 psi deadhead output)


8


Model Length *


STP150-VL1 1½ hp fixed speed VL1 60"-88" $2,035.00 $2,085.00



STPH150-VL1 1½ hp high pressure fixed speed VL1 61"-89" $2,095.00 $2,145.00



STPAG150-VL1 1½ hp AG fixed speed VL1 60"-88" $2,430.00 $2,480.00



STPAGH150-VL1 1½ hp AG high pressure fixed speed VL1 61"-89" $2,490.00 $2,540.00







Model ListF $125.00

K $165.00

R no adder

W no adder

1½ HP Fixed Speed Submersible Turbine Pumps

Notes: 1. STP models are listed for compatibility with fuel mixtures containing up to 10% ethanol with gasoline, diesel fuels, 20% MTBE, 20% ETBE or 17% TAME with gasoline. STPAG models are listed for compatibility with fuel mixtures containing diesel fuel with up to 20% biodiesel, 100% biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline.








9

Model List400137908 $61.00

400818921 STP-CBS, single-phase control box with lockout switch, 110 Volt coil $141.00

402312921 $599.00

402312921 $734.00

402313921 $474.00

402459931 $129.00

402507930 Secondary syphon kit (when two syphon primes are required for one STP) $151.00

5800100215 STP-SCI, single-phase smart controller (when purchased without a 4" STP) $409.00

5800100215 STP-SCI, single-phase smart controller (when purchased with a 4" STP) * $269.00

5800300100 $359.00


Field Installed Options (1½ hp fixed speed specific accessories)Description

Syphon check valve (when ordered with STP)







10

1/3 and 3/4 hp Fixed Speed Submersible Turbine Pump Model Designation SystemA typical turbine model designation has up to five components to define the pump being supplied as follows:STP XXXXX Y-A-B


33 = 1/3 hp fixed speed75 = 3/4 hp fixed speed

A = Model Length

















11


Model Length *


STP33-VL1 1/3 hp fixed speed VL1 55"-83" $1,509.00 $1,559.00






STPAG33-VL1 1/3 hp AG fixed speed VL1 55"-83" $1,904.00 $1,954.00











Model ListF $125.00

K $165.00

R no adder

W no adderModel R check valve, factory installed, for Veeder-Root™ PLLD Line Leak

1/3 and 3/4 HP Fixed Speed Submersible Turbine Pumps






2. STP models are listed for compatibility with fuel mixtures containing up to 10% ethanol with gasoline, diesel fuels, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. STPAG models are listed for compatibility with fuel mixtures containing diesel fuel with up to 20% biodiesel, 100% biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline.


12

Field Installed Options (1/3 and 3/4 hp fixed speed specific accessories)Model List400137908 $61.00

400818921 $141.00

402312921 $599.00

402312921 $734.00

402313921 $474.00

402459931 $129.00

402507930 $151.00

5800100215 $409.00

5800100215 $269.00

5800300100 $359.00

Veeder-Root™ is a trademark of Danaher Corporation.* When purchasing STP-SCI or STP-DHI-SCI in equal quantities of fixed speed 4" STPs







DescriptionSyphon check valve (when ordered with STP)




13

Advanced Protection Submersible Turbine Pump Model Designation SystemA typical turbine model designation has up to five components to define the pump being supplied as follows:STP XXXXX Y-A-B

Model designations may include one or more of the following characters in alphabetical order:

33 = 1/3 hp fixed speed


150 = 1 1/2 hp fixed speed200 = 2 hp fixed speed

VS2 = 2 hp variable speed (implied on IST models unless VS4 is specified)

VS4 = 4 hp variable speed (IST models only)A = Model Length


H = High pressure deadhead output (150 and 200 models only)



STP = Basic Model Designation (IST for variable speed models)


AP = Advanced protection with coated exterior cast surfaces, stainless steel fasteners and piping, alcohol-gasoline compatible)










14

Model Description Model Length *


ISTAPMVS4-VL1 4 hp AP variable speed with MagShell™ 64"-92" $3,009.00 $3,159.00



ISTAPM-1 2 hp AP variable speed with MagShell™ 59"-87" $2,509.00 $2,659.00



STPAPM200-VL1 2 hp AP fixed speed with MagShell™ 63"-91" $3,260.00 $3,410.00



STPAPHM200-VL1 2 hp AP high pressure fixed speed with MagShell™ 63"-92" $3,320.00 $3,470.00



STPAP150-VL1 1 1/2 hp AP fixed speed 60"-88" $2,900.00 $3,050.00



STPAPH150-VL1 1 1/2 hp AP high pressure fixed speed 61"-89" $2,960.00 $3,110.00



STPAP75-VL1 3/4 hp AP fixed speed 57"-86" $2,433.00 $2,583.00



Notes:

1. Remove “M” from model number for non-MagShell™ pump motor assembly (where applicable).


5. All above STPAP models require single-phase, 208-230 VAC, 60 Hz incoming power.6. 4" riser pipe, if supplied locally, must be 4½" OD by 3/16" WT tubing.

Model ListF $125.00

K $165.00

R no adder

W no adder

Description


* Model length (A) defined as the dimension from turbine manifold bottom to pump motor inlet. (please call Customer Service for lead times)

Factory Installed Options (specified in model number at time of STP order)

Advanced Protection Submersible Turbine Pumps (call Customer Service for lead times)

2. STPAP/ISTAP models are listed for compatibility with fuel mixtures containing diesel fuel with up to 20% biodiesel, 100% biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline.

4. All above ISTAP models can only be powered by a MagVFC™. 4 hp models require three-phase incoming power supply, 2 hp models can be supplied with single- or three-phase incoming power.




Model W check valve, factory installed, for Red Jacket™ PPM4000 Line LeakVeeder-Root™ is a trademark of Danaher Corporation. Red Jacket™ is a trademark of Veeder-Root Company.

15

Model List5874202800 $1,081.00400137908 $61.00400818921 STP-CBS, single-phase control box with lockout switch, 110 Volt coil $141.00

402312921 $599.00

402312921 $734.00

402313921 $474.00

402459931 $129.00

402507930 Secondary syphon kit (when two syphon primes are required for one STP) $151.00

5800100215 STP-SCI, single-phase smart controller (when purchased without a 4" STP) $409.005800100215 STP-SCI, single-phase smart controller (when purchased with a 4" STP) * $269.00

5800300100 $359.00


DescriptionMagVFC™, 2 hp or 4 hp variable frequency controller, one required per ISTSyphon check valve (when ordered with STP)

Field Installed Options



STP-DHI-SCI, combo DHI with factory wired STP-SCI (when purchased with a 4" STP) *STP-DHI-SCI, combo DHI with factory wired STP-SCI (when purchased without a 4" STP)

STP-DHI-CBS, combo DHI with factory wired STP-CBSModel 65 psi check valve (for slave of manifolded STPs with Veeder-Root™ PLLD)

16

Fixed Length Submersible Turbine Pump Model Designation SystemA typical turbine model designation has up to five components to define the pump being supplied as follows:STP XXXXX Y-A-B




150 = 1 1/2 hp fixed speed200 = 2 hp fixed speed

A = Model Length








H = High pressure deadhead output (150 and 200 models only)




Model length is expressed as three numeric characters that indicate the length of the STP from the turbine manifold bottom to the pump motor inlet in inches available from 37" to 211" (additional charge for models 133" and longer).




17

Model Description Model Length *


STP33 1/3 hp fixed speed 37"-132" $1,509.00 $1,559.00

STP75 ¾ hp fixed speed 37"-132" $1,568.00 $1,618.00

STP150 1½ hp fixed speed 37"-132" $2,035.00 $2,085.00

STPH150 1½ hp high pressure fixed speed 37"-132" $2,095.00 $2,145.00

STPM200 2 hp fixed speed with MagShell™ 37"-132" $2,395.00 $2,445.00

STPHM200 2 hp high pressure fixed speed with MagShell™ 37"-132" $2,455.00 $2,505.00

Notes:

1. Remove “M” from model number for non-MagShell™ pump motor assembly (2 Hp models only).


4. All above models require single-phase, 208-230 VAC, 60 Hz incoming power.5. 4" riser pipe, if supplied locally, must be 4½" OD by 3/16" WT tubing.

Model ListAG $395.00

F $125.00

K $165.00

R no adder

W no adder

Fixed Length Submersible Turbine Pumps

2. STP models are listed for compatibility with fuel mixtures containing up to 10% ethanol with gasoline, diesel fuels, 20% MTBE, 20% ETBE or 17% TAME with gasoline. STPAG models are listed for compatibility with fuel mixtures containing diesel fuel with up to 20% biodiesel, 100% biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline.




6. For riser pipe lengths 31" to 60", $50.00 adder charge applies.* Model length (A) defined as the dimension from turbine manifold bottom to pump motor inlet. Model length (A) can be a minimum of 37" to a maximum of 211". Add $94.00 to list if model length (A) is 133" to 180" (charge is for boards to protect STP shipment, P/N 400326912). Add $405.00 to list if model length (A) is 181" to 211" (charge is for crating STP, P/N 400326917). Add $716.00 to list if model length (A) is 212" to 246" (charge is for extra crating of STP, P/N 400389112). Please call Customer Service for lead times of model lengths 181" and longer.


Model W check valve, factory installed, for Red Jacket™ PPM4000 Line Leak

Alcohol-gasoline compatible


18

Model List400137908 $61.00

400818921 $141.00

402312921 $599.00

402312921 $734.00

402313921 $474.00

402459931 $129.00

402507930 $151.00

5800100215 $409.00

5800100215 $269.00

5800300100 $359.00






Field Installed Options (fixed speed specific accessories)Description

Syphon check valve(when ordered with STP)







19

MLD+ Mechanical Line Leak Detector (for use with 4" STPs) *Standard Fuel ModelsModel Description List403168901 STP-MLD+G for gas, single pack (blue cover, copper vent tube, brass fittings) $386.00

403168903 STP-MLD+G for gas, three pack $1,051.00

403170901 STP-MLD+D for diesel, single pack (gold cover, copper vent tube, brass fittings) $386.00

403170903 STP-MLD+D for diesel, three pack $1,051.00

403172903 STP-MLD+ Combo, three pack (contains two STP-MLD+G and one STP-MLD+D) $1,051.00

Biofuel ModelsModel Description List403169901 STP-MLD+AG for alcohol-gas, single pack (blue cover, stainless steel tube and fittings) $429.00

403169903 STP-MLD+AG for alcohol-gas, three pack $1,169.00

403171901 STP-MLD+BD for biodiesel, single pack (gold cover, stainless steel tube and fittings) $429.00

403171903 STP-MLD+BD for biodiesel, three pack $1,169.00

Notes:

2. MLD+D models are listed for compatibility with diesel fuels with up to 5% biodiesel and kerosene applications only.

5. All above models will only mount in the 2" NPT leak detector port of a 4" submersible turbine, including competitivemodels, or in a leak detector adapter tee (sold separately below).

* Refer to STP-MLD+ installation manual for complete compatibility specifications.

Model Description List400440101 Vent tube (for use with MLD+G and MLD+D) $8.50

400449903 Hardware pack (fittings and documentation for MLD+G and MLD+D) $17.00

403123001 Vent tube, stainless steel (for use with MLD+AG and MLD+BD) $13.50

400449904 Hardware pack (fittings and documentation for MLD+AG and MLD+BD) $59.00

400518001 Leak detector adapter tee $87.00

MLD+ Repair Parts and Accessories

1. MLD+G are listed for compatibility with fuel mixtures containing up to 10% ethanol with gasoline, diesel fuels, and 20% MTBE, 20% ETBE, or 17% TAME with gasoline.

4. MLD+BD models are listed for diesel with up to 20% biodiesel or 100% biodiesel and kerosene applications only.

3. MLD+AG models are listed for fuel mixtures containing up to 85% ethanol with gasoline and 20% MTBE, 20% ETBE, or 17% TAME with gasoline as well as diesel fuels, fuel oils, kerosene, Avgas and jet fuels.

6. MLD+ models are listed for use with rigid pipelines up to 165.1 gallon capacity, with flexible pipelines up to 109.8 gallon capacity, and with combination rigid/flexible pipelines up to 274.9 gallon capacity.

20

STP-SCI Single-Phase Smart ControllerModel Description List402312921 STP-DHI-SCI, combo DHI with factory wired STP-SCI (when purchased with a 4" STP)* $599.00

402312921 STP-DHI-SCI, combo DHI with factory wired STP-SCI (when purchased without a 4" STP) $734.00

5800100215 STP-SCI, single-phase smart controller (when purchased with a 4" STP)* $269.00

5800100215 STP-SCI, single-phase smart controller (when purchased without a 4" STP) $409.00

Notes:1. SCI models are compatible with all single-phase FE Petro submersibles and competitive makes.2. One SCI required per submersible. Relay rated for 30 Amps (up to 2 hp).3. SCI models are not compatible for use in master/slave configurations with STP-SC models.

STP-DHI Dispenser Hook IsolationModel Description List402312921 STP-DHI-SCI combo DHI with factory-wired STP-SCI (when purchased with a 4" STP)* $599.00

402312921 STP-DHI-SCI, combo DHI with factory-wired STP-SCI (when purchased without a 4" STP) $734.00

402313921 STP-DHI-CBS, combo DHI with factory-wired STP-CBS single-phase control box $474.00

5800300100 STP-DHI, isolates up to eight, 120 Volt dispenser handles $359.00

Notes:

2. DHI models can be connected together for products with more than eight dispenser handle inputs.

DHI Repair Parts and AccessoriesModel Description List223243103 DHI fast-acting fuse, 250 VAC, 1 Amp $5.00

223885930 DHI circuit board, 120 Volt dispenser hook signal $355.00


1. DHI models are compatible with FE Petro submersible pump controllers and competitive pump controller makes accepting 120 Volt dispenser hook signal.

* When purchasing STP-DHI-SCI in equal quantities of fixed speed 4" STPs

21

Single-Phase Control BoxModel Description List400818921 STP-CBS, single-phase control box, with switch and lockout, 120 Volt coil $141.00

402313921 STP-DHI-CBS, combo dispenser hook isolation with factory wired STP-CBS $474.00

Notes:1. CBS models are compatible for use on all single-phase FE Petro submersibles and competitive makes.

2. One CBS required per submersible, relay rated for 30 Amps up to 2 hp.

3. Incorporates pump “ON” indicator light.

4. Relay rated for 220 Volt pumps up to 2 hp, 30 Amps.

STP-CBS Repair Parts and AccessoriesModel Description List403274001 Item #1 - Power switch (replaces 400575001) $40.00

400574001 Item #2 - Power switch bracket $9.50

400158901 Item #3 - Light assembly, 120 Volt $12.50

400215931 Item #4 - Relay, 30A, 120 Volt coil $63.00

400278005 Item #5 - Six position terminal strip $14.00

402410001 Item #6 - CBS terminal strip label $3.00

400817901 Item #7 - Cover and enclosure $43.00

400819001 Item #8 - CBS wiring diagram $3.50

22

Model Description List400660901 Intake filter screen (single pack) $250.00

400660912 Intake filter screen (12 pack carton) $2,712.00

Model Description List402459931 Model 65 psi relief check valve (for slave 4" STP in manifolded applications only) $129.00

Model Description List402507930 Secondary syphon kit $151.00

Intake Filter Screen (mounts to FE Petro or competitive 4" Pump Motors, adds about 1")

Model 65 PSI Relief Check Valve

Secondary Syphon Kit (when two syphon primes required per one 4" STP)

23

Replacement Pump Motor Assemblies *Model Description ListPMA33 1/3 hp pump motor assembly (16" long) $537.00

PMA75 3/4 hp pump motor assembly (18 ¼" long) $621.00

PMA150 1½ hp pump motor assembly (21" long) $842.00

PMAH150 1½ hp high pressure pump motor assembly (21¾" long) $902.00

PMA200 2 hp pump motor assembly (23 ¾" long) $892.00

PMAM200 2 hp pump motor assembly with MagShell™ (23 ¾" long) $892.00

PMAH200 2 hp high pressure pump motor assembly (24 ½" long) $952.00

PMAHM200 2 hp high pressure pump motor assembly with MagShell™ (24 ½" long) $952.00

Note: Remove “M” from model number for non-MagShell™ pump motor assemblies.

Replacement Alcohol-Gasoline (AG) Pump Motor Assemblies *Model Description ListPMAAG33 1/3 hp AG pump motor assembly (16" long) $767.00

PMAAG75 3/4 hp AG pump motor assembly (18 ¼" long) $851.00

PMAAG150 1½ hp AG pump motor assembly (21" long) $1,072.00

PMAAGH150 1½ hp AG high pressure pump motor assembly (21¾" long) $1,132.00

PMAAG200 2 hp AG pump motor assembly (23 ¾" long) $1,122.00

PMAAGM200 2 hp AG pump motor assembly with MagShell™ (23 ¾" long) $1,122.00

PMAAGH200 2 hp AG high pressure pump motor assembly (24 ½" long) $1,182.00

PMAAGHM200 2 hp AG high pressure pump motor assembly with MagShell™ (24 ½" long) $1,182.00


Replacement Variable Speed Pump Motor Assemblies *Model Description ListPMAMVS2 2 hp variable speed pump motor assembly with MagShell™ (20" long) $886.00

PMAAGMVS2 2 hp AG variable speed pump motor assembly with MagShell™ (20" long) $1,116.00

PMAMVS4 4 hp variable speed pump motor assembly with MagShell™ (25" long) $1,336.00

PMAAGMVS4 4 hp variable speed pump motor assembly with MagShell™ (25" long) $1,566.00


* For pump motor assemblies (PMAs) with floating section adapters (1½" NPT female connections), specify “F” in the number; $125 adder charge applies when ordering PMA.



24

4" STP Extractable Sections (less manifold, riser and PMA)Model Description ListSTPEXT-XXX Fixed length (XXX indicates Model Length, minimum of 37" and maximum of 211") * $930.00

STPEXT-VL1 Variable length #1 extractable $1,175.00



STPAGEXT-VL1 AG variable length #1 extractable $1,570.00



STPAPEXT-VL1 AP variable length #1 extractable* $2,040.00



Single-Phase Smart Controller (STP-SCI)Model Description List225000930 Item #1 - SCI lower board control $231.00

225005930 Item #2 - SCI upper board relay $107.00

STP-DHI Dispenser Hook Isolation BoxModel Description List223243103 Item #1 - 250 AC fast-acting fuse $5.00

223885930 Item #2 - 120 Volt circuit board (includes fuse) $355.00

MagVFC™ Model Description List223919930 MagVFC™ fan assembly $129.00

225040930 MagVFC™ user interface board $344.00

228289930 MagVFC™ normally open relay $139.00

* Fixed Length adders apply for Extractable Model Lengths 133" and longer (please call Customer Service for lead times of AP Extractables and Fixed Length Extractables with a model length 181" and longer)

25

PMA, Riser and Check Valve for Variable Length and Fixed Length PumpsModel Description List

400125001 Item #1 - 3/16" × 1-5/8" spiral pin $3.50400615001 Item #2 - Manual pressure relief plug $10.50400615002 Item #2 - Manual pressure relief plug (AG compatible) $11.50400211114 Item #3 - O-ring, Manual pressure relief plug $3.00400627001 Item #4 - Retaining ring, MPR $3.50400616001 Item #5 - Manual pressure relief screw $15.00400616002 Item #5 - Manual pressure relief screw (AG compatible) $17.00400333012 Item #6 - MPR screw, top O-ring (AG compatible) $3.50400333007 Item #7 - MPR screw, bottom O-ring (AG compatible) $3.00400628901 Item #8 - Manual pressure relief plug assembly (includes item #2 & #3) $22.00400628902 Item #8 - Manual pressure relief plug assembly (AG compatible) $23.00400629901 Item #9 - Manual relief screw assembly (includes item #4, #5, #6, & #7) $24.00400629902 Item #9 - Manual relief screw assembly (AG compatible) $25.00400259001 Item #10 - ¼" NPT pipe plug, may be purchased locally $3.00403499001 Item #10 - ¼" NPT pipe plug, may be purchased locally (stainless steel, for AP models) $9.00400137937 Item #11 - Syphon check valve $67.00400221930 Item #12 - Discharge manifold (includes item #1, #8, #9, & #10) $356.00400221931 Item #12 - Discharge manifold (includes item #1, #8, #9, & #10) (for AP models) $471.00151213930 Item #13 - 156" lead assembly $74.00151213932 Item #13 - 240" lead assembly $81.00

Purchase locally Item #14 - Stationary vapor tube, 3/8 OD × 7/20 WT not available

Item #15 - 7" to 19" long $84.00

Item #15 - 20"to 30" long $115.00

Item #15 - 31"to 49" long $147.00

Item #15 - 50"to 60" long $226.00

Item #15 - 7" to 19" long (stainless steel, for AP models) consult factory for lead time $175.00

Item #15 - 20"to 30" long (stainless steel, for AP models) consult factory for lead time $210.00

Item #15 - 31"to 49" long (stainless steel, for AP models) consult factory for lead time $310.00

Item #15 - 50"to 60" long (stainless steel, for AP models) consult factory for lead time $400.00400600002 Item #17 - 5/16-24 × 7/16" set screw for Variable Lengths models only $2.50403432002 Item #17 - 5/16-24 × 7/16" set screw for VL models only (stainless steel, for AP models) $6.50400333015 Item #18 - Lead assembly O-ring $5.00400264009 Item #19 - 5/16-18 × 1-1/8" socket head cap screw, may be purchased locally $3.50

403506001Item #19 - 5/16-18 × 1-1/8" socket head cap screw, may be purchased locally (stainless steel, for AP models)

$8.00

400263004 Item #20 - 5/16" high-collar lock washer, may be purchased locally $2.50

403505001Item #20 - 5/16" high-collar lock washer, may be purchased locally (stainless steel, for AP models) $6.50

403403001 Item #21 - PMA gasket $7.00403403002 Item #21 - PMA gasket (AG compatible) $18.00PMA XXX Item #22 - Pump motor assembly (XXX indicates options & Hp, includes item #30) see PMAs

400981001 Item #23 - 3/8-16 × 1" Hex head screw $3.00Continued on next page

4035229XX Riser, 4-1/2" OD × 4.12" ID (XX =

length)

4001689XX Riser, 4-1/2" OD × 3/16" WT (XX =

length)

26

Model Description List403504001 Item #23 - 3/8-16 × 1" Hex head screw (stainless steel, for AP models) $13.50400285002 Item #24 - 3/8" standard lock washer, may be purchased locally $2.501117703 Item #24 - 3/8" standard lock washer, may be purchased locally (for AP models) $6.50

400197930 Item #25 - Manifold assembly cover (includes item #10, #23, #24, & #26) $74.00

400197931 Item #25 - Manifold assembly cover (includes item #10, #23, #24, & #26) (for AP models) $116.00

400333238 Item #26 - Manifold Cover O-ring (AG compatible) $36.00400147930 Item #27 - Clamp valve assembly (AG compatible) $30.00400174930 Item #28 - Check valve spring $11.50400988931 Item #29 - Standard check valve (includes item #26) $129.00400988934 Item #29 - Standard check valve (AG compatible) $152.00400988932 Item #29 - Model R check valve (includes item #26) $129.00400988935 Item #29 - Model R check valve (AG compatible) $152.00400988933 Item #29 - Model W check valve (includes item #26) $129.00400988936 Item #29 - Model W check valve (AG compatible) $152.00402459931 Item #29 - Model 65 PSI check valve (for slave STP in manifolded applications only) $129.00152350902 Item #30 - PMA hardware pack (includes item #19, #20, & #21) $11.50152350904 Item #30 - PMA hardware pack (AG compatible) (for AP and AG models) $23.00400216905 AG compatible O-ring kit (not shown, includes ten items) $161.00

PMA, Riser and Check Valve for Variable Length and Fixed Length Pumps Continued

27

Discharge Manifold AssemblyModel Description List400192930 Item #1 - Junction box cover (includes item #2) $47.00400210233 Item #2 - Junction Box Cover O-ring $3.50

400655001 Item #3 - Capacitor boot $3.50

400170931Item #4 - Capacitor assembly for 1/3 to 1½ hp, 60 Hz, 15μfd, 370 Volt single-phase (includes one black lead) $43.00

400170934 Item #4 - Capacitor assembly for 2 hp, fixed speed, 60 Hz, 40μfd, 370 Volt single-phase (includes one black lead)

$73.00

400257001 Item #5 - Retaining ring, Female connector $5.50

400258002 Item #6 - 3/8-16 × 1-1/4 Hex head bolt, may be purchased locally $3.00

602011016 Item #6 - 3/8-16 × 1-1/4 Hex head bolt, may be purchased locally (stainless steel, for AP $6.50

400285002 Item #7 - 3/8 standard lock washer, may be purchased locally $2.50

1117703 Item #7 - 3/8 standard lock washer, may be purchased locally (stainless steel, for AP $6.50

400280001 Item #8 - 3/8 standard flat washer, may be purchased locally $2.50

403500001 Item #8 - 3/8 standard flat washer, may be purchased locally (stainless steel, for AP models)

$9.50

400651930 Item #9 - Junction box assembly (includes item #6, #7, & #8) $160.00400651931 Item #9 - Junction box assembly (includes item #6, #7, & #8) (for AP models) $219.00400210212 Item #10 - O-ring, Female connector $3.50

400200930 Item #11 - Wire connector kit (includes male/female connectors, item #5, #10, & #18) $195.00

400200931 Item #11 - Wire connector kit (includes male/female connectors, item #5, #10, & #18) (for AP models)

$258.00

400589930 Item #12 - Extractable Cover (includes item #13) $23.00400210229 Item #13 - O-ring, Extractable Cover $5.50400236903 Item #14 - Contractor’s plug, 4-wire $22.00400259002 Item #15 - 3/8" NPT pipe plug, may be purchased locally $3.00403499002 Item #15 - 3/8" NPT pipe plug, may be purchased locally (stainless steel, for AP models) $9.50400562901 Item #16 - Syphon jet assembly $17.00400562903 Item #16 - Syphon jet assembly (AG compatible) $51.00400211046 Item #17 - O-ring, Extractable (upper, small) $5.00400249001 Item #18 - Retaining ring, Male Connector $2.50400250002 Item #19 - 1/8" dia. × 1/2" roll pin $2.50400333343 Item #20 - AG compatible O-ring, Extractable (upper, large) $43.00400333340 Item #21 - AG compatible O-ring, Extractable (lower) $45.00400259005 Item #22 - 2" NPT square head plug $12.00403499003 Item #22 - 2" NPT square head plug (stainless steel, for AP models) $48.00

28

High Capacity Submersible Turbine Pump Model Designation SystemA typical turbine model designation has up to five components to define the pump being supplied as follows:STP XXXXX Y-A-B

High Capacity model designations may include one or more of the following characters in alphabetical order:

3 = 3 hp fixed speed, 208-230 VAC

5 = 5 hp fixed speed, 208-230 VAC

5H = 5 hp fixed speed, 460 VAC

5G = 5 hp fixed speed, 575 VACA = Model Length


Riser pipe length is expressed as two numeric characters that indicate the total length of the riser in inches. Riser pipes are available from 6" to 60" in three inch increments (additional charge and lead time for risers 27" or longer).


F = Floating suction adapter (3" NPT male adapter)




Y = Pump Motor Horsepower/Electrical Rating


Model length is expressed as three numeric characters that indicate the length of the HCP from the turbine manifold bottom to the pump motor inlet in inches available from 60" to 200" (additional charge for models 132" and longer).

29

Model Description ListSTP3 3 hp 6" STP, three-phase 208-230 VAC $6,231.00

STP5 5 hp 6" STP, three-phase 208-230 VAC $6,484.00

STP5H * 5 hp 6" STP, three-phase 460 VAC $7,324.00

STP5G * 5 hp 6" STP, three-phase 575 VAC $6,921.00

Notes:

2. All models are supplied with a standard check valve unless factory option “R” is specified.

3. All above models require 208-230 VAC, three-phase, 60 Hz incoming power.4. 6" riser pipe, if supplied locally, must be 6-5/8" OD by 1/4" WT tubing.

Model Description ListF Floating suction adapter, 3" male NPT (must be ordered with STP) $189.00

R Model R relief valve factory installed, for Veeder-Root™ PLLD $136.00

Model Description List401165905 Syphon system (when purchased with STP) $176.00

STP-CB3 Three-phase control box, 120 Volt relay, 3 hp, 208-230 Volt, 60 Hz pump control $539.00

STP-CB5 Three-phase control box, 120 Volt relay, 5 hp, 208-230 Volt, 60 Hz pump control $539.00

STP-CB5G Three-phase control box, 120 Volt relay, 5 hp, 575 Volt, 60 Hz pump control $539.00

STP-CBB5H Three-phase control box, 220 Volt relay, 5 hp, 460 Volt, 60 Hz pump control $539.00

STP-SCIII STP-SCIII three-phase smart controller (when purchased with a 6" STP)* $713.00

STP-SCIII STP-SCIII three-phase smart controller (when purchased without a 6" STP) $943.00

Model Description ListSTPHC-EXT-XXX 6" fixed length (XXX indicates Model Length, minimum 60" and maximum 200") * $3,126.00

5. For riser pipe lengths 27" to 60", $100.00 adder charge applies (please call Customer Service for lead times)

1. STP models are listed for compatibility with fuel mixtures containing up to 10% ethanol with gasoline, diesel fuels, 20% MTBE, 20% ETBE or 17% TAME with gasoline.

** Model length (A) defined as the dimension from turbine manifold bottom to pump motor inlet. Model length (A) can be a minimum of 60" to a maximum of 200". Add $130.00 (p/n 401190911) to list if model length (A) is 132" to 170" or add $364.00 (p/n 401190914) to list if model length (A) is 171" to 200" (charges are for additional packaging). Please call Customer Service for lead times of model lengths 132" and longer.

* Fixed Length adders apply for Extractable Model Lengths 132" to 200" (call Customer Service for lead times)

High Capacity Turbine Pumps (available as fixed length models only) **

6" STP Extractable (less manifold, riser and PMA)

Factory Installed Options


Field Installed Options

Note: Three phase smart controller is compatible with FE Petro 208/230 Volt 3 and 5 Hp high capacity STPs and like competitive makes. Not available for 460 or 575 Volt models.

*When purchasing STP-SCIII in equal quantities of fixed speed 6" STPs

* Please call Customer Service for lead time on these items.

30

High Capacity Mechanical Leak Detectors *Model Description List401315902 STP-MLD-HC leak detector complete with Adapter "T" (blue, for gasoline) $1,561.00

401320902 STP-MLD-HCD leak detector complete with Adapter "T" (tan, for diesel) $1,561.00

401315901 Replacement high capacity leak detector ONLY (blue, for gasoline) $1,434.00

401320901 Replacement high capacity leak detector ONLY (tan, for diesel) $1,434.00

401316930 Replacement cover assembly $158.00

401325901 Replacement Adapter "T" with cover assembly $406.00

400449902 MLD-HC hardware pack, includes replacement fittings and documentation $18.00

Notes:

2. MLD-HCD models are listed for compatibility with diesel fuels and kerosene applications only.

3. All above models will only mount in Adapter "T" (p/n 401325901)* Refer to high capacity MLD installation manual for complete fuel compatibility specifications.

1. MLD-HC models are listed for compatibility with fuel mixtures containing up to 10% ethanol with gasoline, diesel fuels, and 20% MTBE, 20% ETBE, or 17% TAME with gasoline.

31

STP-SCIII Three-Phase Smart Controller *Model Description List5800103200 STP-SCIII three-phase smart controller (when purchased with a 6" STP) ** $713.00

5800103200 STP-SCIII three-phase smart controller (when purchased without a 6" STP) $943.00

Notes:1. One STP-SCIII required per submersible, relay rated for 30 Amps.

2. STP-SCIII models do not utilize the pump motor thermal overload wiring (blue leads).

STP-SCIII Repair PartsModel Description List228727101 Item #1 - Three-phase relay, 120 Volt coil (requires rev 1.15) $204.00

223905901 Item #2 - Logic board assembly (rev 1.15) $355.00

223910901 Item #3 - 208-230 Volt power board assembly $172.00

223867102 Item #4 - Mounting Bracket (required update for 228727101) $65.00

STP-CB 3/5 Magnetic StarterModel Description List

401220903STP-CB3 three-phase control box with adjustable overload, 120 Volt relay, 3 hp, 208-230 Volt, 60 Hz pump control $539.00

401220904STP-CB5 three-phase control box with adjustable overload, 120 Volt relay, 5 hp, 208-230 Volt, 60 Hz pump control $539.00

401220993STP-CB5G three-phase control box with adjustable overload, 120 Volt relay, 5 hp, 575 Volt, 60 Hz pump control $539.00

401220933STP-CBB5H three-phase control box with adjustable overload, 220 Volt relay, 5 hp, 460 Volt, 60 Hz pump control $539.00

** When purchasing STP-SCIII in equal quantities of fixed speed 6" STPs

* STP-SCIII is compatible with FE Petro 3 and 5 hp submersibles and competitive makes except the 460 and 575 Volt models.

32

Replacement Pump Motor Assemblies *Model Description ListPMA3 3 hp 208-230 Volt 6" pump motor assembly (33" long) $3,360.00

PMA3RJ 3 hp 208-230 Volt 6" pump motor assembly, replaces competitive model UMP300J4-2HB $3,515.00

PMA5 5 hp 208-230 Volt 6" pump motor assembly (39" long) $3,450.00

PMA5RJ5 hp 208-230 Volt 6" pump motor assembly, replaces competitive model UMP500J4-2K (39" long) $3,605.00

PMA5H ** 5 hp 460 Volt 6" pump motor assembly (39" long) $4,685.00PMA5G ** 5 hp 575 Volt 6" pump motor assembly (39" long) $4,520.00

Syphon SystemModel Description List402505001 Item #1 - Syphon block $63.00

400562901 Item #2 - Syphon jet assembly $17.00

400430004 Item #3 - 3/8"P × 3/8"T compression fitting $5.50

400259001 Item #4 - ¼" pipe plug $3.00

400114001 Item #5 - ¼" close nipple, two required per system $6.50

400114003 Item #6 - ¼" nipple × 3" long $7.00

402510001 Item #7 - ¼" threaded tee $10.50

402511001 Item #8 - ¼" threaded elbow, 90º $10.00

400137937 Item #9 - Syphon check valve $67.00

402544001 Item #10 - Caution tag $19.00

400982001 Item #11 - Security seal $2.50

402553902 Item #12 - Copper tube (HC pump) $8.00

400430003 Item #13 - 1/4"P × 3/8"T compression fitting $5.50

401165930 Syphon unit complete (includes all items above) $204.00

* For pump motor assemblies with floating suction adapters (3" male NPT connections), specify “F” in the model number and $189 adder charge applies (must be ordered with PMA).

** Please call Customer Service for lead time on these items.

33

Model Description List401148101 Item #1 - Connection box cover $67.00

400236909 Item #2 - Seal off plug assembly, 5-wire $23.00

401149001 Item #3 - Eye bolt $18.00

400258001 Item #4 - 3/8-16 × 1" large Hex head cap screw $3.00

400285002 Item #5 - 3/8" lock washer $2.50

401236002 Item #6 - Upper manifold seal $129.00

400273004 Item #8 - 12 gauge wire terminal $3.00

400273006 Item #8 - 14 gauge wire terminal $3.00

401142901 Item #9 - Plug assembly $217.00

401091001 Item #10 - 6-32 × 3/8" large round head machine screw, three required per connector $4.00

401137901 Item #11 - Receptacle assembly $289.00

401238001 Item #12 - Bushing ring, electrical entry $6.50

401239001 Item #13 - Seal plug, electrical entry $48.00

401112101 Item #14 - Discharge manifold $857.00

401163001 Item #15 - 6" flange gasket $21.00

400333235 Item #16 - O-ring, Connectors $24.00

400333234 Item #17 - O-ring, connection box cover $24.00

400258005 Item #18 - 1/2-13 × 1¼" large Hex head cap screw $3.00

400285005 Item #19 - 1/2" lock washer $2.50

400259001 Item #20 - 1/4" pipe plug $3.00

401032901 Item #21 - Model 550 Relief (old standard relief, tire valve - two per submersible) $8.50

401330901 Item #21 - Standard relief (units built since S/N 0302XXXX) $67.00

401330902 Item #21 - Model “R” relief (units built since S/N 0302XXXX) $67.00

401154001 * Item #22 - Valve spring and bracket $73.00

400523001 Item #23 - 10-24 × 3/8" long Sems fastener, two required per bracket $2.50

401150101 * Item #24 - Inset valve assembly $65.00

401236001 Item #25 - Lower manifold seal $142.00

401158903 Item #26 - Air eliminator assembly $71.00

400258006 Item #27 - 3/4-10 × 3" large Hex head cap screw $6.50

401162001 Item #28 - 3" flange gasket $15.00

401113101 Item #29 - 3" companion flange $82.00

Item #30 - 6" riser pipe $178.00

Item #30 - 9" riser pipe $188.00

Item #30 - 12" riser pipe $207.00

Item #30 - 15" riser pipe $221.00

Item #30 - 18" riser pipe $241.00

Item #30 - 21" riser pipe $322.00

Item #30 - 24" riser pipe $344.00

Item #30 - 27" riser pipe (call Customer Service for lead times) $364.00

Item #30 - 30" riser pipe (call Customer Service for lead times) $385.00

Continued on next page

4011910XX 6-5/8" OD × 1/4" WT

(XX = length)

STP3 and STP5 (High Capacity general assembly)

* 401154001 and 401150101 must be replaced together

34

Model Description List400333218 Item #31 - O-ring, lead assembly $17.00

151593906 Item #32 - 192" lead assembly $186.00

401161101 Item #33 - 6" flange $327.00

993517 Item #34 - 3/4" lock washer (400285006) $3.00

400274004 Item #35 - 3/4-10 Hex nut $3.00

400264011 Item #36 - 3/8-16 × 1-1/4" large SHCS $4.00

400333255 Item #37 - O-ring, motor discharge (large, shell) $56.00

402406001 Item #38 - Rubber washer $4.50

400333225 Item #39 - O-ring, motor discharge (small, electrical hub) $10.50

PMA XXX Item #40 - Pump motor assembly (XXX indicates options and horsepower) see PMAs

STP3 and STP5 (High Capacity general assembly) Continued

35

Diesel Exhaust Fluid Pump Motor Assembly Model Designation SystemA typical turbine model designation has four components to define the pump being supplied as follows:DEF PMA YYY Z

150 = 1 1/2 Hp Fixed Speed (5.1" OD x 18.7" long)

A = Single phase, 60 Hz, 208-240 VAC (rated 7.9 Amps, requires 25 microfarad run/start capacitor rated 370 VAC)D = Three phase, 60 Hz, 208-240 VAC (rated 5.0 Amps)

60 Hertz DEF PMAModel Description List403383903 DEF-PMA 150 A: Single Phase, 60hz, 208-240 VAC, 1.5 Hp (single pack) $1,869.00

403383933 DEF-PMA 150 D: Three Phase, 60hz, 208-240 VAC, 1.5 Hp (single pack) $1,999.00

403383703 DEF-PMA 150 A: Single Phase, 60hz, 208-240 VAC, 1.5 Hp (12 pack pallet) $18,519.00

403383733 DEF-PMA 150 D: Three Phase, 60hz, 208-240 VAC, 1.5 Hp (12 pack pallet) $19,749.00

Notes:

Model Description List

403469901 60 Hz, single phase, VL1 69" - 102" (1,750 mm - 2,590 mm) variable length diesel exhaust fluid submersible turbine pump kits (includes VL components #1 - #5 below)

$2,999.00

403470901 60 Hz, single phase, VL2 102" - 166" (2,590 mm - 4,215 mm) variable length diesel exhaust fluid submersible turbine pump kits (includes VL components #1 - #5 below)

$2,999.00

403478901 60 Hz, three phase, VL1 69" - 102" (1,750 mm - 2,590 mm) variable length diesel exhaust fluid submersible turbine pump kits (includes VL components #1 - #4 and #6 below)

$3,129.00

403479901 60 Hz, three phase, VL2 102" - 166" (2,590 mm - 4,215 mm) variable length diesel exhaust fluid submersible turbine pump kits (includes VL components #1 - #4 and #6 below)

$3,129.00

2. Bypass relief valve cracking pressure of 30-40 psi (2.1-2.8 bar) and 4 gpm (15 lpm) minimum flow at the discharge of all models.

3. Non-return check valve cracking pressure of 3 psi (0.2 bar) between product piping and bypass relief valve of all models.

4. Liquid compatibility: All models are intended for use with Diesel Exhaust Fluid (DEF). DEF is a non-flammable, non-combustible liquid that has a specific gravity of 1.09 at 68 ˚F (20˚C), and is made per ISO 22241-1 specifications with 32.5% urea and distilled or deionized water. As defined by ISO 22241-1, DEF is the same as AUS 32® (aqueous urea solution) and also commonly known as AdBlue®

Variable Length Diesel Exhaust Fluid Submersible Turbine Pump Kits

1. Stainless steel construction including impellers/diffusers, inlet/outlet, and outer shell. Viton® or EPDM seals including the 32.8' (10 m) EPDM jacketed power cable. Two-stage, centrifugal type pump with 2" NPT female outlet.

PMA = Pump Motor AssemblyYYY = Pump Motor Horsepower Rating

DEF = Pump Compatible with Diesel Exhaust Fluid ONLY

Z = Pump Motor Horsepower Rating

36


403463901 Item #2 - VL Check valve kit (includes 1½" NPT non-return check valve and 1½" NPT x 4" long nipple on inlet)

$238.00

403461901 Item #3 - VL Bypass kit (includes ½" NPT bypass relief valve, ½" NPT x 1½" NPT bushing in 1½" NPT tee)

$362.00

403454901 Item #4 - VL Pump motor assembly connection kit (includes 2" NPT male inlet x 1½" NPT male outlet EZ FIT connection

$352.00

403383903 Item #5 - 60 Hz, single phase pump motor assembly (DEF-PMA150A) $1,869.00403383933 Item #6 - 60 Hz, three phase pump motor assembly (DEF-PMA150D) $1,999.00


403713921 Single phase electrical kit, 208-240 volt pump control with 120 volt coil (p/n 400818921) & 25 uF / 370 V Capacitor (p/n 400170936, for use with DEF-PMA150A)

$174.00

401220903 Three phase 208-240 volt pump control box with overload protection and 120 volt coil (for use with DEF-PMA150D)

$539.00

403408931 1½" NPT non-return check valve (part of component VL #2, valve only) $217.00

403409931 ½" NPT bypass relief valve (part of component VL #3, valve only) $300.00

403468901 DEF-PMA hardware pack (part of component #5 or #6, includes cable grip, cable ties, and documentation)

$14.50

400170936 Capacitor, 25 uF / 370 V (for use with DEF-PMA150A) $51.00


403464901 Item #2 - FL Check valve kit (includes 2" NPT non-return check valve and 2" NPT x 4" long nipple on inlet)

$347.00

403462901 Item #3 - FL Bypass kit (includes ½" NPT bypass relief valve, ½" NPT x 2" NPT bushing in 2" NPT tee)

$399.00

403456901 Item #4 - FL Pump motor assembly connection kit (includes 2" NPT male inlet x 2" NPT male outlet EZ FIT connection

$435.00

403383903 Item #5 - 60 Hz, single phase pump motor assembly (DEF-PMA150A) $1,869.00

403383933 Item #6 - 60 Hz, three phase pump motor assembly (DEF-PMA150D) $1,999.00


403713921 Single phase electrical kit, 208-240 volt pump control with 120 volt coil (p/n 400818921) & 25 uF / 370 V Capacitor (p/n 400170936, for use with DEF-PMA150A)

$174.00

401220903 Three phase 208-240 volt pump control box with overload protection and 120 volt coil (for use with DEF-PMA150D)

$539.00

403408932 2" NPT non-return check valve (part of component FL #2, valve only) $321.00

403409931 ½" NPT bypass relief valve (part of component FL #3, valve only) $300.00

403468901 DEF-PMA hardware pack (part of component #5 or #6, includes cable grip, cable ties, and documentation)

$14.50

400170936 Capacitor, 25 uF / 370 V (for use with DEF-PMA150A) $51.00

Variable Length Accessories & Repair Parts

Fixed Length Diesel Exhaust Fluid Submersible Turbine Pump Kits

Fixed Length Accessories & Repair Parts

Variable Length Diesel Exhaust Fluid Submersible Turbine Pump Replacement Kits

37

Underground Storage Tank Equipment300 Vapor Check Valve AdapterModel Description List30021001 4" vapor check valve adapter, anodized aluminum $133.00

30022001 4" vapor check valve adapter, brass $225.00

30030001 4" X 3" vapor check valve adapter, anodized aluminum $145.00

30030031 4" X 3" vapor check valve adapter, anodized aluminum-BSPP $101.00

304 4" Vapor Recovery CapModel Description List30420001 Glass-filled nylon $52.50

30420002 Glass-filled nylon w/ chain $48.00

30430101 Epoxy coated aluminum* $71.00

30430102 Epoxy coated aluminum w/ chain $89.0030430103 Biofuel cap** $71.00

77711101 Replacement gasket for 304-200-01 $7.75


*CARB: EVR Phase 1 certification VR-101 and VR-103 and Missouri MOPETP APCP-002-001-99.

**Biofuel approved model (E85 and biodiesel), CARB: EVR Phase 1 certification VR-101.

306/708 4" Coaxial Vapor Recovery Adapters/Drop TubesModel Description List30630001 4" coaxial vapor recovery adapter, hard coated aluminum $87.00

30630021 4" coaxial vapor recovery adapter, hard coated aluminum-BSPT $77.00

708335901 4" coaxial vapor recovery adapter, poppetted coaxial vapor recovery adapter $233.00

70822604-2 4" x 13' coaxial drop tube, two per box $525.00

708336901 Poppeted coaxial adaptor and drop tube kit $506.00

708340901 Tightening Tool $120.00

38

308 Ball Float Vent Valves2" Ball FloatsModel Description List308020003 2" Ball float , NPT , 3" nipple AGB $132.00

308020205 2" Ball float ,NPT , 5.12" nipple AGB $135.00

308020107 2" Ball float , NPT , 7" nipple AGB $133.00



308023003 2" Ball float , BSPT , 3" nipple AGB $124.00




*Does not inlcude installation cage

3" Ball FloatsModel Description List308030005 3" Ball float, NPT, 5" nipple AGB $342.00

308030011 3" Ball float, NPT, 11" nipple AGB $353.00





Installation CagesModel Description List30822802 2" Threaded Adaptor-NPT $69.00

30822803 3" Threaded Adaptor-NPT $69.00

300 Series Extractor Vent ValvesModel Description List31040011 Extractor Valve Without cage, 4" x 4" x 2" $146.00

31140011 Extractor Valve Without cage, 4" x 4" x 3" $150.00

33040011 Extractor Valve Without cage, 4" x 4" x 3" x 2", biofuels $205.00

33140011 Extractor Valve Without cage, 4" x 4" x 3" x 3" $168.00

34040011 Extractor Valve With cage, 4" x 4" x 2" x 2" $181.00

39

Extractor Vent Valve Accessories4" Brass Pipe CapModel Description List76020101 4" pipe cap $128.00

5' Extractor WrenchModel Description List32110001 5' extractor wrench $340.00

362 Vapor Shear ValveModel Description List36220603 1" × 1-1/2" NPT thread vapor shear valve $186.00

36220621 1" x 1-1/2" BSPT thread vapor shear valve $191.00

662 Emergency Shut-off ValvesModel Description List662500901 Single poppet, union, 1½” NPT, E-coat AGB $219.00

662500902 Single poppet, female, 1½” NPT, E-coat AGB $146.00

662500903 Single poppet, male, 1½” NPT, E-coat AGB $150.00

662510902 Single poppet, female, 1½” BST, E-coat AGB $152.00

662510903 Single poppet, male, 1½” BSPT, E-coat AGB $155.00

662501901 Double poppet, union, 1½” NPT, E-coat AGB $252.00

662501902 Double poppet, female, 1½” NPT, E-coat AGB $184.00

662501903 Double poppet, male, 1½” NPT, E-coat AGB $188.00

662511902 Double poppet, female, 1½” BSPT, E-coat AGB $191.00

662511903 Double poppet, male, 1½” BSPT, E-coat AGB $194.00

662502902 Double poppet, N/C, female, 1½” NPT, E-coat AGB $191.00

40

Emergency Shut-off Valve AccessoriesU-Bolt KitModel Description List66213801 662 shear valve U-bolt kit $22.25

Fulcrum ArmModel Description List66218501 662 shear valve Fulcrum arm with Hex $10.25

Emergency Shut-off Valve Replacement Tops1-1/2" Union Replacement Adapter ModelsModel Description List662500201 Emergency shut-off valve replacement tops, pressure, single poppet union $175.00

662501201 Emergency shut-off valve replacement tops, pressure, double poppet union $184.00

1-1/2" Female Replacement Adapter ModelsModel Description List662500202 Emergency shut-off valve replacement tops, pressure, single poppet female $65.00662501202 Emergency shut-off valve replacement tops, pressure, double poppet female $116.00

662502202 Emergency shut-off valve replacement tops, suction (normally closed), double poppet female

$92.00

662510202 Emergency shut-off valve replacement tops, pressure, single poppet female-BSPT $42.00

662511202 Emergency shut-off valve replacement tops, pressure, double poppet female-BSPT $121.00

1-1/2" Male Replacement Adapter ModelsModel Description List662500203 Emergency shut-off valve replacement tops, pressure, single poppet male $71.00

662501203 Emergency shut-off valve replacement tops, pressure, double poppet male $113.00

662510203 Emergency shut-off valve replacement tops, pressure, single poppet male-BSPT $74.00

662511203 Emergency shut-off valve replacement tops, pressure, double poppet male-BSPT $121.00

775 4" Side Seal Fill CapModel Description77520201 4" side seal fill cap $82.00

77510401 4" replacement gasket $16.25

776 4" Side Seal Fill AdapterModel Description77630001 4" side seal fill adapter $130.00

77630031 4" side seal fill adapter-BSPT $129.00

41

777 4" Top Seal Fill CapsModel Description List77720102 4" top seal fill cap, Biofuel approved** $59.00

77720201 4" top seal fill cap, Aluminum, epoxy coated grey $77.00

77711101 4" top seal fill cap replacement nitrile gasket $7.75


**Biofuel approved model (E85 and biodiesel), CARB: Phase 1 certification VR-101.

778 Top Seal Fill Pipe AdapterModel Description List77830101 Top seal fill pipe adapter, 4" with lugs-NPSM* $116.00

77830102 Top seal fill pipe adapter, 4" without lugs* $117.00

77830105 Top seal fill pipe adapter, 4" with lugs** $166.00

77830201 Top seal fill pipe adapter, 3" with lug-NPSM $135.00

77830302 Top seal fill pipe adapter, 4" composite with gasket-NPSM $52.50

78020001 Top seal fill pipe adapter, 3" without lugs-NPSM $90.00

77830132 Top seal fill pipe adapter, 4" without LUGS-BSPP $107.00

77830231 Top seal fill pipe adapter, 3" with LUGS-BSPP $135.00

77830332 Top seal fill pipe adapter, 4" COMPOSITE with Gasket- BSPP $54.75



*Missouri #99-08

**Biofuel compatible model (E85 and biodiesel).

SWF-100-B Top Seal Swivel Fill Pipe AdapterModel Description ListSWF-100-SS 4" swivel fill adapter, stainless steel** $314.00SWF-100-B 4" swivel fill adapter, brass* $411.00

SWFV-PKGSS Includes one SWF-100-SS and one SWV-101-SS swivel adapter** $730.00

SWFV-PKG Includes one SWF-100-B and one SWV-101-B swivel adapter* $1,003.00

70541201 RCA SS Swivel Fill Kit (Includes one 70521305 5" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

$403.00

*EVR Phase 1 certification VR-101 and VR-103 and Missouri MOPETP APCP-0002-001-99.

**EVR Phase 1 certification VR-101 for gas and E85.

SWV-101-B Vapor Swivel AdapterModel DescriptionSWV-101-SS 4" stainless steel vapor swivel adapter, stainless steel** $425.00SWV-101-B 4" vapor swivel adapter, brass* $567.00SWFV-PKGSS Includes one SWF-100-SS and one SWV-101-SS swivel adapter** $730.00

SWFV-PKG SWF-100-B and one SWV-101-B swivel adapter* $1,003.00

70541301RCA SS Vapor SWIVEL Kit (includes one 70521305 5" nipple, one 77720102 4"TOP SEAL and one SWV-101-SS vapor swivel adapter) $522.00

*EVR Phase 1 certification VR-101 and VR-103, tracer tight approved and Missouri MOPETP APCP-0002-001-99.**EVR Phase 1 certification VR-101 for gas and E85.

42

779 3" Top Seal Fill CapModel Description List77920001 3" top seal fill cap $91.00

77420203 Replacement Buna-N gasket $8.25

Autolimiter® II Automatic Shutt-off ValveModel Description List70849101 Dual Point 172.00 in. $754.00

70849404 Dual Point valve/adapter kit $655.00

70849424 Dual Point valve/adapter kit-AGB*** $911.00

***Biofuel Compatible (E-85/Biodiesel)

Remote Fill KitModel Description List70832002 Remote fill kit for Autolimiter $341.0070832012 Remote fill kit for Defender OPV $341.00

782 Drop TubesModel Description List78220212 2" x 12' drop tubes, 6 per box $86.00

78220312 3" x 12' drop tubes, 4 per box $105.00

78220410-2 4" x 10' drop tubes, 2 per box* $233.00



78220430-2 4" x 10' drop tubes, 2 per box** $595.00

78220432-2 4" x 12' drop tubes, 2 per box** $680.00

*CARB: EVR Phase 1 certification VR-101 and VR-103.

**Biofuel approved models (E85 and biodiesel). CARB: EVR Phase 1 certification VR-101.

Probe Cap and Adapter KitModel Description List90037-E S-Kit A/S Cap & Adapter NPT ½" $144.00

77711101 Replacement nitrile gasket for cap $7.75

Tank Bottom ProtectorsModel Description78520002 Zinc plated carbon steel with plastisole coating $216.00

TBP-3516-E Tank bottom protector** $122.00

**Biofuel approved model E85 and biodiesel).

PV-ZERO™ Pressure/Vacuum Vent ValveModel Description407215901 PV-ZERO pressure/vacuum vent valve, 3" NPT $2,349.00407225901 PV-ZERO test cap assembly, gas and E85 $461.00407220001 PV-ZERO gas/E85 fluid $213.00

Note: May require four to eight week lead time. Consult factory for availability.

43

Defender Series™ Complete Model Number Reference ChartDefender Series spill container model numbers can be created using the following guidelines:Defender Series™ Model Number Reference ChartDefender Series spill container model numbers can be created using the following guidelines:705-XXX-ZABCDXXX = Containment options Table for Defender Series™ Overfill Prevention Valve (selection C) 545 = Single wall Alpha Description 555 = Double wall A OPV with 5' top drop tube, 8' bottom drop tubeZ = Interstitial Monitoring B OPV with 5' top drop tube, 10' bottom drop tube0 = No Sensor C OPV with 5' top drop tube, 8' bottom drop tube, AGB compatible1 = I2 Monitor (float gauge) D OPV with 5' top drop tube, 10' bottom drop tube, AGB compatible2 = TSP-ULS Sensor E OPV with 10' top drop tube, 8' bottom drop tubeA = Base Thread F OPV with 10' top drop tube, 10' bottom drop tube0 = NPSM G OPV with 10' top drop tube, 8' bottom drop tube, AGB compatible1 = NPT H OPV with 10' top drop tube, 10' bottom drop tube, AGB compatible2 = BSPT I OPV coaxial with with 6.5' top drop tube, 8' bottom drop tubeB = Drain J OPV coaxial with with 6.5' top drop tube, 10' bottom drop tube1 = with Drain2 = without DrainC = Overfill Prevention Valve (See table)D = Riser, Cap, and Adapter1 = St. Steel swivel fill adapter, Cap and nipple2 = No riser cap or adapter

K OPV poppeted coaxial with 6.5' top drop tube, 8' bottom drop tube, AGB compatible

L OPV poppeted coaxial with 6.5' top drop tube, 10' bottom drop tube, AGB compatible

44

Defender Series™ 5 Gallon Spill Container Complete Item DescriptionModel List

705545001A1 $1,770.00

705545002A1 $1,766.00

705545011A1 $1,777.00

705545012A1 $1,681.00

705555101A1 $2,005.00

705555102A1 $1,953.00

705555111A1 $2,276.00

705555112A1 $2,165.00

705555201A1 $2,373.00

705555202A1 $2,359.00

Description

Spill container, single wall, NPSM thread, with drain, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, single wall, NPSM thread, w/o drain, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, single wall, NPT thread, with drain, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, single wall, NPT thread, without drain, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, double wall, NPSM thread, with drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)


Spill container, double wall, NPSM thread, w/o drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, double wall, NPT thread, with drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, double wall, NPT thread, w/o drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, double wall, NPSM thread, with drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, NPSM thread, without drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

45

Model List

705555211A1 $2,492.00

705555212A1 $2,477.00

705545001F1 $1,959.00

705545002F1 $1,955.00

705545011F1 $1,966.00

705545012F1 $1,955.00

705555101F1 $2,295.00

705555102F1 $2,240.00

705555111F1 $2,579.00

705555112F1 $2,463.00

Contined from previous page


Description

Spill container, single wall, NPSM thread, with drain, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, single wall, NPSM thread, without drain, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, single wall, NPT thread, with drain, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, single wall, NPT thread, without drain, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, double wall, NPt thread, with drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

spill container, double wall, NPSM thread, with drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, double wall, NPSM thread, without drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, NPT thread, without drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, double wall, NPT thread, with drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, double wall, NPT thread, without drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

46

Model List

705555201F1 $2,681.00

705555202F1 $2,666.00

705555211F1 $2,681.00

705555212F1 $2,666.00

Continued from previous page

Spill container, double wall, NPt thread, with drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, NPT thread, without drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Spill container, double wall, NPSM thread, with drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

Description

Spill container, NPSM thread, without drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid with Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube and RCA SS Swivel Fill Kit (Includes one 70521305 2.88" nipple, one 77720102 4" TOP SEAL CAP and one SWF100SS swivel fill adaptor)

47

Defender Series™ Overfill Prevention Valve

Model List

708591901 $746.00

708591902 $825.00

708591921 $1,061.00

708591922 $1,140.00

708592901 $877.00

708592902 $956.00

708592921 $1,061.00

708592922 $1,140.00

708593901 $1,061.00

708593902 $1,140.00

708593923 $1,350.00

708593924 $1,428.00

708594901 $693.00

708594902 $693.00

708535901 $436.00

708530930 $31.50

708534901 $105.00

Defender Series™ overfill prevention valve only with coaxial top adapter, AGB compatible*

Roll crimping tool

Replacement roll crimper tool roller bit for retrofit with existing tool

Remote testing tool, 11' long sectional/collapsible

*Alcohol, gas, biofuel compatible (E-85, gasoline and biodiesel) models come with hard coated anodized drop tubes for full compatibility.

Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube


Description

Defender Series™ overfill prevention valve with 5' top drop tube, 8' bottom drop tube, AGB compatible*

Defender Series™ overfill prevention valve with 5' top drop tube, 10' bottom drop tube, AGB compatible*



Defender Series™ overfill prevention valve with 10' top drop tube, 8' bottom drop tube, AGB compatible*Defender Series™ overfill prevention valve with 10' top drop tube, 10' bottom drop tube, AGB compatible*

Defender Series™ overfill prevention valve, coaxial with 6.5' top drop tube, 8' bottom drop tube

Defender Series™ overfill prevention valve, coaxial with 6.5' top drop tube, 10' bottom drop tube

Defender Series™ overfill prevention valve, poppeted coaxial with 6.5' top drop tube, 8' bottom drop tube

Defender Series™ overfill prevention valve, poppeted coaxial with 6.5' top drop tube, 10' bottom drop tube

Defender Series™ overfill prevention valve only with top adapter, AGB compatible*

48

Defender Series™ Model Number Reference ChartDefender Series spill container model numbers can be created using the following guidelines:

705-XXX-ZABXXX = Containment options545 = Single wall

555 = Double wall

Z = Interstitial Monitoring0 = No Sensor

1 = I2 Monitor (float gauge)

2 = TSP-ULS Sensor

A = Base Thread0 = NPSM

1 = NPT

2 = BSPT

B = Drain1 = with Drain

2 = without Drain

CI-GKT suffix is a cast iron gasketed lid. Call for additional options.

49

Defender Series™ Spill Container with I2 MonitorModel List

705545001 $783.00

705545002 $755.00

705545001CI-GKT $824.00

705545002CI-GKT $818.00

705555101CI-GKT $1,196.00

705555102CI-GKT $1,136.00

705555201CI-GKT $1,626.00

705555202CI-GKT $1,610.00

705545011CI-GKT $832.00

705545012CI-GKT $818.00

705545021CI-GKT $845.00

705545022CI-GKT $830.00

705555111CI-GKT $1,512.00

705555112CI-GKT $1,383.00

705555121CI-GKT $1,397.00

705555211CI-GKT $1,626.00

705555212CI-GKT $1,610.00

705559901 $6,561.00

Description

Defender Series™ 5 gallon spill container, single wall, NPSM thread, without drain, no cover

Defender Series™ 5 gallon spill container, single wall, NPSM thread, with drain, no cover

Defender Series™ 5 gallon spill container, single wall, NPSM thread, with drain, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, single wall, NPSM thread, without drain, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, double wall, NPSM thread, with drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, double wall, NPSM thread, without drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, double wall, NPSM thread, with drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, NPSM thread, without drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, single wall, NPT thread, with drain, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, single wall, NPT thread, without drain, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, single wall, BSPT thread, with drain, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, single wall, BSPT thread, without drain, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, double wall, NPT thread, with drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, double wall, NPT thread, without drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, double wall, BSPT thread, with drain, with I2 monitor, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, double wall, NPt thread, with drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid

Defender Series™ 5 gallon spill container, NPT thread, without drain, with TSP-ULS sensor, with gray epoxy-coated cast iron gasketed lid

Defender Series™ spill container cutaway display, double wall, with drain, with I2 monitor

50

Defender Series™ Spill Container Replacement PartsModel List

70550311 Spill container seal-ring $38.00

602256001 Tank riser gasket $16.25

1103939 DT riser clamp o-ring $14.00

70551101 I2 monitor $41.00

70551002 Inspection port (I2 monitor) $42.00

70551001 Inspection port (sensor) $42.00

70550901EC DT riser clamp $128.00

70533729 Pull to push drain valve Kit $75.00

70553001 Snow plow ring assembly $124.00

70544011 Cover, cast iron w/ gasket (gray) $162.00

1115601 Slotted hex head self-tapping screw $2.25

70553111 Drain chain an clip $20.00

705555101SP BKT ASM,DW,AGB,I2,DRN,NPSM $898.00

705555102SP BKT ASM,DW,AGB,I2,ND,NPSM $842.00

705555201SP BKT ASM,DW,AGB,SEN,DRN,NPSM $1,101.00

705555202SP BKT ASM,DW,AGB,SEN,DN, NPSM $1,352.00

Defender Series™ Spill Container ToolsModel List

T-7001 T-handle wrench $276.00

T-7106 Double-ended installation tool $306.00

T-7107 Double wall vacuum test kit (for double wall models only) $198.00

Description

Description

51

Phil-Tite Spill Container Replacement PartsModel Description List85100-1 Replacement 5 gallon 85000-1 fi ll spill bucket, with drain valve* $738.00

85101-1 Replacement 5 gallon 85000-1 vapor spill bucket, without drain valve* $642.00

85100 Replacement 3.5 gallon Phil-Tite spill bucket, with drain valve $738.00

85101 Replacement 3.5 gallon Phil-Tite spill bucket, without drain valve $642.00

85000-1 and 85100-1 Spill Collector Fill Spill BucketModel Description List85011-1 Grey ductile cast iron cover with wiper seal $340.00

SC-1513V U-shaped seal for ductile cast iron lid $86.00

PP-1005-TB Fill debris bucket insert, without pump $71.00

PP-1005-TBP Vapor debris bucket insert, with pump $128.00

85031-1 Stainless steel retaining ring for screen and filter $53.75

85035 Shut-off collar to screen, upper O-ring $15.00

85039 1/4" fl at seal-riser tube, inner O-ring $16.25

85036 Outer spill bucket U-shaped seal for 85000 Series $57.75

85036-1 Outer spill bucket U-shaped seal for 85000-1 Series $63.00

85009 Direct bury stainless steel sleeve $346.00

85400 Drain valve handle and valve assembly $407.00

702, 705, and 715 Grade Level Spill ContainersComposite Base Spill ContainersModel Description70547101BLK Grade level, 5 gallon, with drain, composite base, blk frc cover $615.00

70547301BLK-S Grade level, 5 gallon, with drain, composite base, blk snap on frc cover $700.00

71547101BLK Grade level, 15 gallon, with drain, composite base, blk frc cover $791.00

Cast Iron Base Spill ContainersModel w/ Drain Description70547001BLK Grade level, 5 gallon, with drain, cast iron base, blk frc cover $596.00

70547201BLK-S Grade level, 5 gallon, with drain, cast iron base, blk snap on frc cover* $671.00

70547965CI-GKT Grade level, 5 gallon, with drain, cast iron base, cast iron cover with gasket, RCA* $780.00

70547901CI-GKT Grade level, 5 gallon, with drain, cast iron base, cast iron cover with gasket* $624.00

70549001BLK Grade level, 5 gallon, with drain, cast iron base, blk frc cover, CARB stage I EVR** $700.00

71547001BLK Grade level, 15 gallon, with drain, cast iron base, blk frc cover $758.00

Model w/o Drain Description70545801BLK Grade level, 5 gallon, no drain, cast iron base, blk frc cover $557.00

70547202BLK-S Grade level, 5 gallon, no drain, cast iron base, blk snap on frc cover* $671.00

70547902CI-GKT Grade level, 5 gallon, no drain, cast iron base, cast iron cover with gasket* $750.00

70549002BLK Grade level, 5 gallon, no drain, cast iron base, blk frc cover, CARB stage I EVR** $626.00

71547202BLK-S Grade level, 15 gallon, no drain, cast iron base, blk snap on frc cover $744.00

52

Retrofit Spill ContainersModel w/ Pump Description List70240001BLK Grade level, 5 gallon, slip on, HDPE, black FRC cover, with pump $559.00

70240465CI-GKT Grade level, 5 gallon, slip on, HDPE, riser cap adapter, cast iron cover with gasket, with pump*

$528.00

70240501BLK-S Grade level, 5 gallon, slip on, HDPE, black snap on FRC cover, with pump $632.00

Model w/o Pump Description List70240402CI-GKT Grade level, 5 gallon, slip on, HDPE, CI cover with gasket, no pump* $462.00

70240601BLK Grade level, 5 gallon, slip on, HDPE, blk FRC cover, no pump $433.00

*ULC approved, MH21091

**CARB Phase 1 EVR approved, VR-103RCA references include riser, cap and adapter

12" Replacement Covers For Grade Level Spill ContainersModel Description List70517101 Replacement clips for snap-on covers $11.25

70533301 12" cover FRC black snap-on* $215.00

70540900 12" cover Aluminum $116.00

70542002 12" cover FRC white with black cross, regular unleaded $143.00

70542003 12" cover FRC red with white cross, premium unleaded $143.00

70542301 12" cover FRC standard black cover $107.00

70542302 12" cover FRC white $143.00

70542303 12" cover FRC red $143.00

70542305 12" cover FRC yellow $143.00

70542307 12" cover FRC orange $143.00

70542309 12" cover FRC brown $143.00

70543000 12" cover Cast iron without handle $111.00

70544011 12" cover Cast iron with gasket-AGB $162.00

71043001 12" cover Aluminum watertight for use on 705 and 715 grade level spill containers $488.00

*Snap-on lids fit only on special snap-on spill containers. Please consult factory. Minimum quantities may apply.

53

702, 705, and 715 Below Grade Level Spill ContainersComposite Base Spill ContainersModel Description70547501BLK Below grade, 5 gallon, composite base, with drain, BLK 18" FRC cover* $1,122.00

Cast Iron Base Spill ContainersModel w/ Drain Description List70544501BLK Below grade, CAPD, 5 gallon, cast iron base, with drain, BLK 18" FRC cover $1,078.00

70547401BLK Below grade, 5 gallon, cast iron base, with drain, BLK 18" FRC cover* $1,203.00

70547465BLK Below grade, 5 gallon, cast iron base, with drain, BLK 18" FRC cover, RCA* $1,244.00

70549201BLK Below grade, 5 gallon, cast iron base, with drain, BLK 18" FRC cover, CARB stage I EVR** $1,068.00

71547401BLK Below grade, 15 gallon, cast iron base, with drain, BLK 18" FRC cover* $1,290.00

71547465BLK Below grade, 15 gallon, cast iron base, with drain, RCA, BLK 18" FRC cover* $1,283.00

71549201BLK Below grade, 15 gallon, cast iron base, with drain, BLK 18" FRC cover, CARB stage I EVR** $1,189.00

Model w/o Drain Description List705477NDBLK Below grade, 5 gallon, cast iron base, no drain, BLK 18" FRC cover* $1,305.00

70549202BLK Below grade, 5 gallon, cast iron base, no drain, BLK 18" FRC cover, CARB stage I EVR** $1,078.00

71549202BLK Below grade, 15 gallon, cast iron base, no drain, BLK 18" FRC cover, CARB stage I EVR** $1,119.00


**CARB Phase 1 approved, VR-103

Replacement 18" Manway CoversModel Description List78130401 FRC black, raintight 18" $172.00

78130402 FRC white, raintight 18" $245.00

78130403 FRC red, raintight 18" $245.00

78130405 FRC yellow, raintight 18" $245.00

78130407 FRC orange, raintight 18" $245.00

78130601 Steel 18" $152.00

Retrofit Spill ContainersModel w/ Pump Description70245001BLK Below grade, 5 gallons, slip on, with pump, BLK 18" FRC cover* $880.00

70245065 Below grade, 5 gallons, slip on, with pump, No cover, RCA* $924.00


54

7-1/2", 12" and 18" Round ManwaysModel w/ Pump Description List78120808 7.5" diameter CI cover manhole, 8" skirt $87.00

78121212CI 12" diameter CI cover manhole, 12" skirt $126.00

78121212CI-H 12" diameter CI cover manhole, with handle, 12" skirt $138.00

78121224CI 12" diameter CI cover manhole, 24" skirt $256.00

78141808BLK 18" diameter manhole, BLK FRC cover, 8" skirt $293.00



78147865 18" diameter manhole, BLK FRC cover, 8" skirt, bolted $660.00

Replacement Round Manway CoversModel w/ Drain Description List78130201 12" black FRC cover $182.00

78130207 12" orange FRC cover $182.00

78130401 18" BLK FRC cover $172.00

78130601 18" steel cover $152.00

78140001 12" cast iron cover $74.00

78140201 7.5" cast iron cover $34.75

78140701 12" cast iron cover with handle $75.00

SRC18WRS 18" steel bolt down cover $160.00

Steel ManwaysSquare ManwayModel DescriptionSSQ2409 24.00 × 24.00 steel square manhole $408.00

55

Round ManwaysModel Description List78141808STL 18" non bolted manhole, steel cover, 8" skirt $240.00

78141812STL 18" non bolted manhole, steel cover, 12" skirt $243.00

78141818STL 18" non bolted manhole, steel cover, 18" skirt $250.00

SR1809WT 18" steel manhole bolted, 9" skirt $322.00

SR2409HD 24" steel manhole, 9" skirt $452.00



SR3609WT 36" steel manhole, bolted, 9" skirt $903.00


SR3809WT 38" steel manhole, bolted, 9" skirt $990.00

SR4209HD 42" steel manhole, 9" skirt $1,589.00

SR4209WT 42" steel manhole, bolted, 9" skirt $1,577.00

SR4809HD 48" steel manhole, 9" skirt $1,944.00

SR4809WT 48" steel manhole, bolted, 9" skirt $2,104.00

Note: May require two week lead time. Consult factory for availability.

16" and 24" Square Manways With Knock Down SkirtsModel Description List98710001 16.00 × 16.00 square steel manhole, 7.5" skirt $235.00

98720001 24.00 × 24.00 square steel manhole, 9" skirt $335.00

FLEX-ING Probe Access ManholeModel Description20URTATG Probe access manhole $339.00

Square Manway Replacement CoversModel Description78920301 16" × 16" steel cover, square $109.00

98720101 24" × 24" steel cover, square $192.00

1102103 Nut $3.50

56

12", 30", 36" and 42" Fiber Reinforced Composite Manways12" Round FRC CoversModel Description List78130201 12" (12.88") round BLK FRC cover $182.00

78130207 12" (12.88") round ORG FRC cover $182.00

30" Round FRC CoversModel Description List78145906 30" (32") round FRC cover, grey bolted $776.00

78149006 30" (32") round FRC cover, grey $785.00

36" Round FRC CoversModel Description List78145606 36" (39.50) round FRC cover, grey bolted $875.00

78144806 36" (39.50) round FRC cover, grey $895.00

78148206 36" (39.50) round FRC cover, grey slide action $982.00

42" Round FRC CoversModel Description List78144106 42" (44.25") round FRC cover, grey bolted $1,247.00

78144506 42" (44.25") round FRC cover, grey $1,221.00

78148306 42" (44.25") round FRC cover, grey slide action $1,337.00

12" Round Manways with FRC CoversModel Description78121212BLK 12" (12.88") round BLK FRC manway, 12" skirt $239.00

78121212ORG 12" (12.88") round ORG FRC manway, 12" skirt $273.00

30" Round Manways with FRC CoversModel Description78143012GRY 30" (32") round manway with grey bolted FRC cover, 12" skirt $1,127.00

78143013GRY 30" (32") round manway with grey FRC cover, 12" skirt $1,125.00

36" Round Manways with FRC CoversModel Description78143312GRY 36" (39.50") round manway with grey bolted FRC cover, 12" skirt $1,407.00

78143313GRY 36" (39.50") round manway with grey FRC cover, 12" skirt $1,270.00

78148512GRY 36" (39.50") round manway with grey slide action FRC cover, 12" skirt $1,260.00

57

42" Round Manways with FRC CoversModel Description List78144312GRY 42" (44.25") round manway with grey bolted frc cover, 12" skirt $1,668.00

78144318GRY 42" (44.25") round manway with grey frc cover, 18" skirt $1,571.00

78144412GRY 42" (44.25" × 52.00") round manway with grey bolted frc cover, 22" skirt $2,770.00

78144313GRY 42" (44.25") round manway with grey frc cover, 12" skirt $1,654.00

78148612GRY 42" (44.25") round manway with grey slide action frc cover, 12" skirt $1,687.00

36" FRC Aramid CoversModel Description List78044806 36" (39.50") frc Aramid cover, grey $1,311.00

78045606 36" (39.50") frc Aramid cover, grey bolted $1,311.00

Note: Please contact Customer Service for lead times.

42" FRC Aramid CoversModel Description List78044106 42" (44.25") frc Aramid cover, grey bolted $1,740.00

78044506 42" (44.25") frc Aramid cover, grey $1,731.00


36" FRC Manway with FRC Aramid CoversModel Description List780492BD Bolted cover with 12" skirt $1,724.00

780492NB 12" skirt $1,603.00

780492SA Slide action cover $1,864.00

780492SB Slide action cover wih bolt-down option $1,900.00


42" FRC Manway with FRC Aramid CoversModel Description780491BD Bolted cover with 12" skirt $2,130.00

780491NB 12" skirt $2,066.00

780491SA Slide action cover $2,314.00

780491SB Slide action cover wih bolt-down option $2,363.00


58

Composite Access CoversModel Description ListPCC90 35" (900mm) composite access cover $1,473.00

PCC90-DIP 35" (900mm) composite access cover with integrated dip inspection port $1,477.00

PCC90-SK Fiberglass skirt for PCC90 $343.00

PCC-H Lifting handle tool for PCC90 composite access cover $102.00

PCC-J Replacement gasket for PCC90 composite access cover (between lid and frame) $111.00

PCR106 42" (1,060mm) composite access cover $1,575.00

PCR106-DIP 42" (1,060mm) composite access cover with integrated dip inspection port $1,838.00

PCR106-OCH1400-SK Fiberglass skirt for PCR106, for use with OCH tank camber $305.00

PCR106-TSM4542-SK Fiberglass skirt for PCR106, for use with TSM tank camber $289.00

PCR-LIFT Lifting handle tool for PCR106 composite access cover $378.00

FLEX-ING Composite Manhole LidsModel Description List14U-3810 38” Composite manhole lid, ring, and 10” skirt $733.00

14U-RT3810 38” Raintight Composite manhole lid, ring, and 10” skirt $958.00

14U-RT3810CL 38” Raintight Composite manhole with 10” skirt and cam locks $912.00

14U-3810C 38” Composite manhole lid only $564.00

14U-4210 42” Composite manhole lid, ring, and skirt (10”) $809.00

14U-RT4210 42” Raintight Composite manhole lid, ring, and skirt (10”) $995.00

14U-RT4210CL 42” Raintight Composite manhole with skirt (10”) and cam locks $947.00

14U-4210C 42” Composite manhole lid only $655.00

59

FLEX-ING Replacement Composite Manhole LidsModel Description List14U-39R 39” RLine Composite Replacement Lid (Replaces OPW’s standard Conquistador) $670.00

14U-44R 44” RLine Composite Replacement Lid (Replaces OPW’s standard Conquistador) $738.00

14U-39MOR 39” MORCORE Composite Replacement Lid (Replaces Morrison composite lids) $733.00

14U-44MOR 44” MORCORE Composite Replacement Lid (Replaces Morrison composite lids) $846.00

14U-44MOR2 44” MORCORE Composite Replacement Lid, 2.17” depth (Replaces Morrison composite lid $846.00

FLEX-ING Replacement Handle KitModel Description ListHANDLE KIT Replacement handle kit $64.25

FLEX-ING Replacement Gasket KitsModel Description List

BOLT KIT Replacement gasket and bolt kit for bolt down style lids (includes gasket material and four bolts) $32.75

NONBOLT KIT Replacement gasket kit for non bolt down (lay in and cam lock) style lids (includes gasket material only) $21.50

CAMLOCK KIT Replacement gasket and hardware for cam lock style lids (includes four cam locks, eight nuts, four bolts, four O-rings and gasket material $162.00

FLEX-ING Universal Lifting and Cam Lock ToolModel Description ListEUEVHANDLE Universal lifting and cam lock tool $224.00

Containment ManholeModel Description81830701 Replacement cover with “monitoring well” on top $198.00

60

Monitoring Test Well ManwaysModel Description List80840001 8" cast iron $192.00

81030201 10" cast iron $195.00

81430201 14" cast iron $258.00

Monitoring Test Well AccessoriesMonitoring Test Well Cap PlugsModel Description List77210201 4" monitoring test well cap plug $41.00

77210601 2" monitoring test well cap plug $28.50

77210901 6" monitoring test well cap plug $74.00

PVC Well Screen Filter WrapModel Description List77310002 2" well screen filter wrap - 100' $180.00

77310004 4" well screen filter wrap - 100' $275.00

Monitoring Test Well Screen PipeModel Description List77320001 2" x 13' monitoring test well screen pipe $101.00

77320002 4" x 13' monitoring test well screen pipe, 27 lbs. $184.00

77320003 6" x 13' monitoring test well screen pipe $385.00

77320004 4" x 15' monitoring test well screen pipe, 31 lbs. $217.00


Monitoring Test Well PackageModel Description808-4-K 808-400-01 manway, 772-102-01 cap plug, 773-200-02 test well screen pipe $402.00

810-6-K 810-302-01 manway, tts-109-01 cap plug, 773-200-03 test well screen pipe $639.00Note: Please contact Customer Service for lead times.

61

787 Series Fuel IdentificationModel Description List78710003 D - diesel kit $46.25

78710006 SU - super unleaded kit $48.50

78710009 RU - regular unleaded kit $48.50

78710101 Aluminum base only $27.00

78710203 D - brass letter only $21.00

78710206 SU - brass letter only $21.00

78710209 RU - brass letter only $21.00

787 Series Fill IdentifierModel Description List78710302 Fill replacement plate $21.00

78720101 High-grade unleaded kit, red $82.00

78720102 Low-grade unleaded kit, white $82.00

78720103 Diesel kit,yellow $82.00

78720104 Mid-grade unleaded kit, blue $82.00

62

Defender Series Multiport ManwaysModel Number Refernce ChartX-Y-Z-AX = Size and StyleDMP36 = 36" Defender multiport DMP36R = 36" Defender multiport retrofit for Phil-Tite Multiport

DMP42 = 42" Defender multiport DMP42R = 42" Defender multiport retrofit for Phil-Tite Multiport

Y = Number of Spill Containers1 = One spill container

2 = Two spill containers

4 = Four spill containers

Z = Container ConfigurationSW = Single wall, NPSM SWT = Single wall, NPT

DWI = Double wall, I 2 monitor, NPSMDWS = Double wall, ULS sensor, NPSM

DWIT = Double wall, I 2 monitor, NPT DWST = Double wall, ULS Sensor, NPT

A = Cover ColorYEL = Yellow

RED/ORG = Red and orange

WHT/ORG = White and orange

63

Defender Series Multiport Manway PackagesModel w/ Pump Description List

DMP36-1-SW-YEL 36" Defender Multiport, One Spill Container, One 8" access port, Yellow CI Lid

$2,810.00

DMP36-2-SW-RED/ORG 36" Defender Multiport, Two Spill Containers, One 8" access port, One Red/One Orange CI Lids

$3,953.00

DMP36-2-SW-WHT/ORG 36" Defender Multiport, Two Spill Containers, One 8" access port,One White/One Orange CI Lids

$3,953.00

DMP36R-1-SW-YEL 36" Defender Multiport Retrofi t Kit, One Spill Container, One 8" access port, Yellow CI Lid

$2,200.00

DMP36R-2-SW-RED/ORG 36" Defender Multiport Retrofi t Kit, Two Spill Containers, One 8" access port, One Red/One Orange CI Lids

$3,295.00

DMP36R-2-SW-WHT/ORG 36" Defender Multiport Retrofi t Kit, Two Spill Containers, One 8" access port, One White/One Orange CI Lids

$3,295.00

DMP42-1-SW-YEL 42" Defender Multiport, One Spill Container, One 8" access port, Yellow CI Lid

$3,237.00

DMP42-2-SW-RED/ORG 42" Defender Multiport, Two Spill Containers, One 8" access port,One Red/One Orange CI Lids

$4,466.00

DMP42-2-SW-WHT/ORG 42" Defender Multiport, Two Spill Containers, One 8" access port,One White/One Orange CI Lids

$4,466.00

DMP42-4-SW-WHT/ORG 42" Defender Multiport, Four Spill Containers, One 6" access port,Two White/Two Orange CI Lids

$6,675.00

DMP42R-1-SW-YEL 42" Defender Multiport Retrofi t Kit, One Spill Container, One 8" access port, Yellow CI Lid

$2,519.00

DMP42R-2-SW-RED/ORG 42" Defender Multiport Retrofi t Kit, Two Spill Containers, One 8" access port, One Red/One Orange CI Lids

$3,669.00

DMP42R-2-SW-WHT/ORG 42" Defender Multiport Retrofi t Kit, Two Spill Containers, One 8" access port, One White/One Orange CI Lids

$3,669.00

DMP42R-4-SW-WHT/ORG 42" Defender Multiport Retrofi t Kit, Four Spill Containers, One 6" access port, Two White/Two Orange CI Lids

$5,958.00

DMP36-1-DWIT-YEL 36” Defender multiport, one double wall NPT spill container, I2 monitor, one 13” access port, yellow cast iron lid

$3,169.00

DMP36-1-SWT-YEL 36” Defender multiport, one NPT spill container, one 13” access port, yellow cast iron lid

$2,810.00

DMP36-1-SWTN-YEL 36” Defender multiport, one NPT spill container,no drain, one 13” access port, yellow cast iron lid

$2,783.00

DMP36-2-DWIT-RED/ORG 36" Defender multiport, two double-wall NPT spill containers, I2 monitor, one 8" access port, one red/one orange cast iron lid

$4,645.00

DMP36-2-DWIT-WHT/ORG 36" Defender multiport, two double-wall NPT spill containers,I2 Monitor, one 8" access port, one white/one orange cast iron lid

$4,645.00

DMP36-2-SWBT-WHT/ORG 36” Defender multiport, two BSPT spill containers, one 8” access port, one white/one orange cast iron lid

$3,953.00

DMP36-2-SWT-RED/ORG 36" Defender multiport, two NPT spill containers, one 8" access port, one red/one orange cast iron lid

$3,953.00

64

Defender Series Multiport Manway Packages continued

DMP36-2-SWT-WHT/ORG 36" Defender multiport, two NPT spill containers, one 8" access port, one white/one orange cast iron lid $3,953.00

DMP36-2-SWTN-RED/ORG 36" Defender multiport, two NPT spill containers, no drain, one 8" access port, one red/one orange cast iron lid $3,924.00

DMP36-2-SWTN-WHT/ORG 36" Defender multiport, two NPT spill containers, no drain, one 8" access port, one white/one orange cast iron lid $3,924.00

DMP42-1-SWT-YEL 42” Defender multiport, one NPT spill container, one 13” access port, yellow cast iron lid $3,237.00

DMP42-2-DWI-RED/ORG 42" Defender multiport, two double-wall NPSM spill containers, I2 monitor, one 8" access port, one red/one orange cast iron lid $5,158.00

DMP42-2-DWI-WHT/ORG 42" Defender multiport, two double-wall NPSM spill containers,I2 Monitor, one 8" access port, one white/one orange cast iron lid $5,158.00

DMP42-2-DWS-RED/ORG 42" Defender multiport, two double-wall NPSM spill containers, with TSP-ULS sensor, one 8" access port, one red/one orange cast iron lid $6,061.00

DMP42-2-DWS-WHT/ORG42" Defender multiport, two double-wall NPSM spill containers,with TSP-ULS sensor, one 8" access port, one white/one orange cast iron lid $6,061.00

DMP42-2-SWT-RED/ORG 42" Defender multiport, two NPT spill containers, one 8" access port, one red/one orange cast iron lid $4,466.00

DMP42-2-SWT-WHT/ORG 42" Defender multiport, two NPT spill containers, one 8" access port, one white/one orange cast iron lid $4,466.00

65

Dual Point Fill Watertight Multi-port Sump Packages42" Single and Double Wall Octagonal*Model Description List

DMM4236-2/1-OB-SSump Kit for Defender Multiport,medium burial,42" sump riser,36" manhole,Octagonal Base, Single Wall $3,242.00

DMM4236-2/1-OC-SSump Kit for Defender Multiport,medium burial,42" sump riser,36" manhole,Octagonal Base, Single Wall $2,694.00

DMM4842-4/0-OC-HSump Kit for Defender Multiport,medium burial,48" sump riser,42" manhole,Octagonal Base, Double Wall $6,657.00


*All 42" octagonal multi-port sumps have a 42" base diameter, minimum 36" manway size and a 39" riser diameter.

Diesel Watertight Multi-port Sump Packages*Model Description List

DMM4236-1/0-OB-SSump Kit for Defender Multiport,medium burial,42" sump riser,36" manhole,Octagonal Base, Single Wall $3,157.00


*All 42" octagonal multi-port sumps have a 42" base diameter, minimum 36" manway size and a 39" riser diameter.

Multi-port Watertight Sump Shield Packages*Model Description

DMP36-1-WTSS-3236" Defender Multiport Water Tight Sump Shield, 32" sump riser, One Spill Container $1,796.00

DMP36-2-WTSS-3236" Defender Multiport Water Tight Sump Shield, 32" sump riser,Two Spill Containers,One Access Port $1,911.00

DMP36-1-WTSS-3336" Defender Multiport Water Tight Sump Shield,33" bottleneck sump riser,One Spill Container $1,506.00

DMP36-1-WTSS-4236" Defender Multiport Water Tight Sump Shield,42" sump riser,One Spill Container $1,536.00

DMP36-2-WTSS-3336" Defender Multiport Water Tight Sump Shield,33" bottleneck sump riser,Two Spill Containers,One access port $1,564.00

DMP36-2-WTSS-4236" Defender Multiport Water Tight Sump Shield,42" sump riser,Two Spill Containers,One access port $1,593.00


DMP42-2-WTSS-4242" Defender Multiport Water Tight Sump Shield,42" sump riser,Two Spill Containers; One Access Port $1,699.00


66

Multi-port Watertight Sump Shield Packages ContinuedModel Description List

DMP42-4-WTSS-4242" Defender Multiport Water Tight Sump Shield,42" sump riser,Four Spill Containers; One Access Port $1,940.00


DMP36-2-WTSS-4836" Defender Multiport Water Tight Sump Shield,48" sump riser,Two Spill Containers,One Access port $1,796.00

*See catalog for recommended applications

Watertight Fiberglass Multi-port Sump Package AccessoriesFiberglass Seam Adhesive KitModel Description List

FG-SEAMKIT Includes matte, resin, putty and catalyst for one fiberglass seam, single or double wall.

$223.00

Note: Double wall applications may require two seam kits per seam.

BootsModel Description ListWTRB-1315 REDUCING BOOT,13"-15" W/C $125.00

CapsModel Description

WTRC-0600 6" rubber cap with clamp for 6" access opening in watertight sump shield $71.00



67

Flexible ConnectorsModel Description ListDEF10X10MXEZM 1" dia DEF flex w/ 1" hex male by EZ Fit 1" male; 10" OAL $166.00

DEF15X18MXEZM 1½" dia DEF flex w/ 1½" hex male by EZ Fit 1½" male; 18" OAL $331.00

DEF15X18MXM 1½" dia DEF flex w/ 1½" hex male by 1½" hex male; 18" OAL $268.00

DEF20X12MXM 2" dia DEF flex w/ 2" hex male by 2" hex male; 12" OAL $385.00

DEF20X18MXEZF9 2" dia DEF flex w/ 2" hex male by EZ Fit 2" 90° hex female; 18" OAL $386.00

DEF20X18MXM 2" dia DEF flex w/ 2" hex male by 2" hex male; 18" OAL $407.00

FF07X14HMXM346 ¾" dia flex w/ ¾" hex male by ¾" male 346 swivel; 14" OAL $88.00

FF10X18HMXM346 1" dia flex w/ 1" hex male by 1" male 346 swivel; 18" OAL $104.00

FF15X12F346XEZ 1½" dia flex w/ 1½" female 346 swivel by 2" EZ fit flange; 12" OAL $157.00

FF15X12HMXM346 1½" dia flex w/ 1½" hex male by 1½" male 346 swivel; 12" OAL $133.00

FF15X12M346XF 1½" dia flex w/ 1½" male 346 swivel by 1½" hex female; 12" OAL $146.00

FF15X14BTXBTS 1½" dia flex w/ 1½" BSPT hex male by 1½" BSPT male 346 swivel; 14" OAL $119.00




FF15X18M346X2F 1½" dia flex w/ 1½" male 346 swivel by 2" hex female; 18" OAL $149.00




FF20X12F346XEZ 2" dia flex w/ 2" female 346 swivel by 2" EZ fit flange; 12" OAL $199.00



FF20X18BTXBTS 2" dia flex w/ 2" BSPT hex male by 2"BSPT male 346 swivel; 18" OAL $160.00


FF20X18M346XF 2" dia flex w/ 2" male 346 swivel by 2" hex female; 18" OAL $210.00

FF20X24BTXBTS 2" dia flex w/ 2" BSPT hex male by 2" BSPT male 346 swivel; 24" OAL $173.00


FF20X24HMXMS90 2" dia flex w/ 2" hex male by 2" 90° male 346 swivel; 24" OAL $375.00

FF20X24M346XF 2" dia flex w/ 2" male 346 swivel by 2" hex female; 24" OAL $217.00

FFUL15X12HMXHM 1½" dia flex w/ 1½" hex male by 1½" hex male; 12" OAL $116.00




FFUL20X15HMXHM 2" dia flex w/ 2" hex male by 2" hex male; 15" OAL $143.00



FFUL20X30HMXF 2" dia flex w/ 2" hex male by 2" hex female; 30" OAL $185.00


FFUL30X18MXM 3" dia flex w/ 3" male by 3" male; 18" OAL $273.00




68

Flexible Connector EZ FIT AccessoriesModel Description ListEZFITXEZFIT EZ FIT x EZ FIT $69.00

EZBLANK EZ FIT blank $30.25

EZ30BLANK 3" EZ FIT blank $56.75

EZXEZX20BV EZ FIT x EZ FIT x 2" ball valve $248.00

EZX20BV EZ FIT x 2" ball valve $189.00

EZXEZ90 EZ FIT x EZ FIT x 90º $102.00

EZ30XEZ3090 3" EZ FIT x 3" EZ FIT x 90º $191.00

EZXEZXEZTEE 2" EZ FIT x 2" EZ FIT x 2" EZ FIT 1½" tee $145.00

EZ30XEZ30XEZ30T 3" EZ FIT x 3" EZ FIT x 3" EZ FIT tee $432.00

EZ20XEZ20TEEFF 2" EZ FIT x 2" EZ FIT x 2" EZ FIT tee 2" $177.00

EZX15HM90 EZ FIT x 1½" hex male 90º $82.00

EZX20HM90 EZ FIT x 2" hex male 90º $91.00

EZX30M90 EZ FIT x 3" male 90º $134.00

EZX20HF90 EZ FIT x 2" female 90º $102.00

EZX20FG90 EZ FIT x 2" female glue pipe for FRP 90º $83.00

EZX30FG90 3" EZ FIT x 3" female glue pipe for FRP 90º $216.00

EZX20FGTEE EZ FIT x 2" female glue pipe for FRP tee $147.00

EZX15HMPL 1½" EZ FIT x hex male $42.00

EZX20HMPL 2" EX FIT x hex male $47.25

EZX30MP 3" EZ FIT x 3" male $82.00

EZX20HFPL EZ FIT x 2" female $53.75

EZ30X30FP 3" EZ FIT x 3" female $144.00

EZX20FGPL EZ FIT x 2" female glue pipe for FRP $49.50

EZX30FGPL 3" EZ FIT x 3" female glue pipe for FRP $105.00

EZCLAMP 2" EZ FIT clamp $21.75

EZ30CLAMP 3" EZ FIT clamp $38.00

407493001 1" EZ FIT gasket $7.00

407493002 2" EZ FIT gasket $20.00

407493003 3" EZ FIT gasket $32.00

69

Ball ValvesModel Description ListBV150FPSS 1½" ball valve, stainless steel $249.00

BV150FPBRASS 1½" ball valve, brass $92.00

BV200FPSS 2" ball valve, stainless steel $453.00

BV300FPBRASS 3" ball valve, brass $451.00

Flexible Connector Isolation AccessoriesYellow Jacket Easy Fit BootModel Description ListYJVSLEEVE 30" Yellow Jacket Easy Fit boot with Velcro™ seal $70.00

YJVSLEEVE25 25' Yellow Jacket Easy Fit boot with Velcro™ seal $686.00

YJVSLEEVE50 50' Yellow Jacket Easy Fit boot with Velcro™ seal $1,370.00

YJVSLEEVEII30" Yellow Jacket Easy Fit boot with Velcro™ seal, adhesive, straps and two mounting collars $96.00

Yellow Jacket BootModel Description ListYJ32BOOT 3½" ID x 30" Yellow Jacket boot $59.00

YJ32BOOTKIT-40 3½" ID x 40" Yellow Jacket boot boot, adhesive, straps and two mounting collars $98.00

Yellow Jacket Heat Shrink WrapModel Description ListYJHS03 36" Yellow Jacket heat shrink wrap $78.00

YJHS20 20' Yellow Jacket heat shrink wrap $543.00

YJHS50 50' Yellow Jacket heat shrink wrap $1,356.00

Yellow Jacket Heat Shrink WrapModel DescriptionFLEXWRAP47X03 4.7" x 3' heat shrink sleeve $142.00

DEF Flexible ConnectorsModel DescriptionDEF10SSBVKIT DEF ball valve kit $429.00

DEF20X12MXM 2" x 12" DEF hose, hex male x hex male $385.00

DEF20X18MXEZF9 2" x 18" DEF hose, hex male x EZ FIT female NPT 90° $386.00

DEF15X18MXM 1½" x 18" DEF hose, hex male x hex male $268.00

DEF07X16HMXEZHM ¾" x 16" DEF hose, hex male x EZ FIT hex male $152.00

DEF15X18MXEZM 1½" x 18" DEF hose, hex male x EZ FIT hex male $331.00

DEF10X12MXM 1" x 12" DEF hose, hex male x hex male $115.00

70

DEF Shear ValvesModel Description663100001 DEF shear valve, 1½" NPT inlet, 1" outlet $305.00

663100021 DEF shear valve, 1½" BSPT inlet, 1" outlet $305.00

66320000 Mounting bracket for DEF shear valve including U-bolt, nuts and bracket guides $44.25

Pipe Guards & BollardsU-Shaped Pipe GuardsModel Description ListBGU35565414 3.5" x 36" x 54" x 14" $237.00

BGU35365510SS4 3.5" x 36" x 55" x 10" Stainless Steel #4 finish $1,361.00

BGU35415314 3.5" x 41" x 53" x 14" $237.00

BGU35485014 3.5" x 48" x 50" x 14" $237.00

BGU40365614 4.0" x 36" x 56" x 14" $320.00

BGU40415314 4.0" x 41" x 53" x 14" $320.00

BGU40417414 4.0" x 41" x 74" x 14" $350.00

BGU40435414 4.0" x 43" x 54" x 14" $321.00

BGU40485114 4.0" x 48" x 51" x 14" $321.00

BollardsModel Description ListBGS4042 4.0" x 42" $98.00

BGS4063 4.0" x 63" $120.00

BGS4072 4.0" x 72" $162.00

BGS6063 6.0" x 63" $249.00

BGS6072 6.0" x 72" $285.00

BGS4072SS4 4.0" x 72" Stainless Steel #4 finish $927.00

BGS6084 6.0" x 84" $333.00

Remote Fill BoxesModel Description ListRFBP-TOP 3" pre-plumbed box, top inlet $3,369.00

RFBP-REAR 3" pre-plumbed box, rear inlet $3,065.00

RFBNP-REAR 3" box only (not plumbed), rear inlet $1,420.00

Wall Mount Remote Fill BoxesModel Description ListRFBNP-WALL Wall mount remote fill box not plumbed $1,614.00

RFBP-WALL Wall mount remote fill box plumbed $3,531.00

71

Aboveground Storage Tank Equipment605, 606, 616 and 636 Anti Syphon ValvesModel Description List60530001 .75", 0'12' head pressure range, 3.4 lbs. $283.00

60630001 1", 0'12' head pressure range, 3.2 lbs. $292.00

61630001 1.5", 5'12' head pressure range, 4.6 lbs. $291.00





664 Pressure Regulator ValveModel Description List66430201 MaleNPT $898.00

66430202 Union $947.00

66430206 Femalepoppeted $912.00

66430203 FemaleNPT $898.00

66430226 FemaleBSPT $956.00

66222001 Male replacement adapter $41.00

66421101 Female replacement adapter for 66430206 $74.00

66430401 Mounting bracket $119.00

706 AST Spill ContainerModel Description List70534101 Replacement drain valve $49.50

70642001 Standard $861.00

Note: ULC file CMH 1667.

709 Warden® AST Overfill Prevention ValveModel Description List70942001 Warden®, 4" overfi ll with inverted floats $1,442.00

77421220 2" dust cap $26.00

770 Locking Fill CapModel Description List77010101 2" watertight locking fill cap $88.00

72

751 2" Aluminum Fill CapModel Description75120201 Female lockable fill cap $55.75

75120401 Male lockable fill cap $47.25

800 Tank VentsModel Description80020301 3" EBW tank vent $60.00

80020702 2" EBW tank vent $32.75

802 Pressure Vacuum VentsModel Description80230301 2", 1.88 lbs., NPT threaded EBW pressure vacuum vent* $114.00

80230302 2", 1.84 lbs., Oring seal EBW pressure vacuum vent* $128.00

80230312 2", 1.88 lbs., Oring seal EBW pressure vacuum vent* $154.00

80230321 2", 1.88 lbs., BSPT threaded EBW pressure vacuum vent* $114.00

80230405 3", 2.44 lbs., NPT threaded EBW pressure vacuum vent* $143.00

80230406 3", 2.4 lbs., Oring seal EBW pressure vacuum vent $147.00

* UL file #MH 15882

803 Aboveground Emergency VentsModel Description80320001 6" x 4.5", 4" NPT thread $163.00

80320501 8.06" x 5.19", 6" NPT thread $250.00

80330801 10.5" x 5.5", 8" NPT thread $378.00

73

Suction System Equipment50-201 Brass Foot ValvesModel Description List5010501 1/2" single poppet $92.00

5110001 1/2" double poppet $165.00

7510501 3/4" single poppet $94.00

7610001 3/4" double poppet $206.00

10010501 1" single poppet $100.00

10110001 1" double poppet $206.00

15020201 1-1/2" single poppet $158.00

15120001 1-1/2" double poppet $247.00

20020001 2" single poppet $212.00

20120001 2" double poppet $311.00

320 Foot Valve ExtractorModel Description List32030201 4" x 4" x 1.5" $478.00

32030202 4" x 4" x 2" $500.00

Replacement PartsModel Description List32010201 Suction stub adapter $160.00

32010301 Cap assembly $114.00

32110001 Extractor wrench $340.00

32010401 Kit - cap with gasket $128.00

325 Product Line Isolation ValveModel Description List32530001 4.00 × 4.00 × 2.00 $263.00

32110001 Extractor wrench, 14 lbs. $340.00

32510001 2" test plug $103.00

515 and 516 Brass Vertical Check ValvesModel Description List51520001 1.5" single poppet $157.00

51620001 1.5" double poppet $227.00

615 and 635 Angle Check ValvesModel Description List61530101 1.5" single poppet $135.00

61530201 1.5" single poppet, spring loaded $204.00

63520101 2" single poppet $273.00

74

621 and 622 Under Pump/In-Line Check ValvesModel Description List62020101 1.5" without pressure relief (one threaded end) $83.00

62120001 1.5" without pressure relief (both ends threaded) $102.00

62130001 1.5" with pressure relief $117.00

62220001 2" without pressure relief $129.00

62230001 2" with pressure relief* $154.00

*Dresser.

650 Union Check ValveModel Description List65010402 1.5" with screen $43.25

65010802 1.5" without screen $41.00

75

Installation ToolsWrenchesModel Description List32110001 60" extractor wrench $340.00

90110101 3/4" chain wrench $267.00

Flaring ToolModel Description ListT-6100-FT Flaring tool kit for flaring drop tubes $1,475.00

Spill Container Tool KitModel Description ListT-7001 T-handle for installation tool kit $276.00

T-7002-A Black heavy duty adapter used to install removable Phil-Tite spill buckets $299.00

T-7002HD Heavy duty spill bucket removal tool, includes T-7002-A adapter and T-handle with handle weights

$469.00

T-7043 Tool kit required to install a Phil-Tite spill container, tool kit items listed above, including T-7001, T-7002A, T-7102

$826.00

T-7100 Red adapter tool used to remove old fill non-swivel adapters with lugs $223.00

T-7102 Orange adapter tool, used to remove or install SWF-100-B and SWV-101-B swivel adapters and M/F 4×4 riser adapters

$260.00

T-7103 Blue adapter tool, used to install OPW tall swivel adapters $260.00

T-7104 Green torque adapter tool for static torque testing on any swivel adapter $260.00

T-7200 Cast iron cover removal tool $209.00

T-7106 Defender Series spill container installation tool $306.00

T-7107 Defender Series spill container double wall vacuum test kit $198.00

76

AccessoriesDebris BucketsModel Description ListPP-1005-TB Debris bucket without pump $71.00

PP-1005-TBP Debris bucket with pump $128.00

M/F 4×4Model Description ListMF 4x4 4" × 4" threaded riser adapter $140.00

Alignment BracketsModel Description ListM-1600 Riser alignment bracket for 16" center $206.00

Cover Removal ToolModel Description ListT-7200 Cast iron cover removal tool $209.00

77

Replacement PartsUnderground Storage Tank EquipmentModel Description List90074 Fulcrum arm kit $10.00

1103001 Shear valve adapter bolts, socket head cap screw 5/16-18" × 5/8" long $4.75

1103011 Fusible length screw, socket head cap screw 6-32" × 1/4" long $4.75

1103305 Socket set screw, 1/4-20" × 1/4" long $3.00

1103401 362 vapor shear valve seal ring, square cut, Buna ID 2-1/8" $5.00

1118201 4" drop tube gasket $7.25

1137201 Autolimiter® cold weld bonding compound $66.00

30330101 Coaxial connection fi tting $81.00

70849603 Autolimiter® 8’ thread-on replacement bottom tube (2-pack) $375.00

95021501 777-201 biofuel cap replacement gasket $18.75

Spill ContainersModel Description List90022 EBW grade level spill container drain cover kit $14.00

1106703 Below grade spill container fl exible head cap screw 1/4-20" × 1/2" long $5.00

70210501 Kit: gasket, plate, 4" screws $79.00

70230101 Pump with safety instruction sheet $104.00

70512001 Drain valve assembly $27.00

70512201 Assembly gasket, plate and bolts $28.50

70521501 705 grade level push drain assembly $52.50

70521506 705 below grade push drain assembly $52.50

70522601 705 grade level and below grade drain valve gasket $10.25

70533218 Pull-push drain assembly kit $74.00

70533219 Pull-push drain assembly kit, fl at style $86.00

70533299 Pull-push drain assembly kit, converter $128.00

70533401 12" cover gasket-FRC $29.75

70533601 705 grade level and below grade pull drain assembly $70.00

70533602 715 grade level and below grade pull drain assembly $63.00

70533603 725 below grade pull drain assembly $73.00

70534101 Pull-push drain valve assembly $49.50

70541701 Styrofoam collar $15.00

70825501 Drain valve isolation kit $201.00

70849801 Autolimiter® installation kit $66.00

71040114 Below grade spill container spare cover assembly $460.00

71040201 Below grade spill container cover $360.00

71520301 EBW 15 gallon push drain assembly $117.00

78

Spill Containers ContinuedModel Description List71520501 Replacement handle for below grade spill container $26.00

78910201 Cover gasket - BG 18" $30.75

85010 Multi-port stainless steel sleeve, 3 tabs $407.00

85011-1 Phil-Tite spill container cover assembly, grey $340.00

85032 Bellows and screen $87.00

85100 Replacement 3-1/2 gallon fill spill container $738.00

85101 Replacement 3-1/2 gallon vapor spill container $642.00

602047903 Phil-Tite spill container cover assembly, red $366.00

602047905 Phil-Tite spill container cover assembly, white $366.00

602047906 Phil-Tite spill container cover assembly, yellow $366.00

602047909 Phil-Tite spill container cover assembly, orange $366.00

602132902 Phil-Tite Multiport 36" cover assembly, one 13" opening $1,313.00

602132920 Phil-Tite Multiport 36" cover assembly, fill/vapor spill containers, one 8" opening SPR $2,082.00

602132914 Phil-Tite Multiport 36" cover assembly, double spill container, one 8" opening, grey cover $2,085.00

602133909 Phil-Tite Multiport 42" cover assembly, double spill container, one 8" opening $3,092.00

602133960 Phil-Tite Multiport 42" cover assembly with snow plow ring, quadruple spill container, one 6" opening $4,200.00

602132914OR Phil-Tite Multiport 36" cover assembly, double spill container, one 8" spill container $2,083.00

602132914OW Phil-Tite Multiport 36" cover assembly, double spill container, one 8" spill container $2,083.00

602250001 Drop tube seal $20.00

602256001 Non-CARB seal, 1/4" fl at $16.25

85031-1 5 gallon spare retaining ring $53.75

85039-DT Phil-Tite EVR drop tube seal $18.75

AC-0600-O-RING 6" access O-ring $10.25

602345905 6" × 1/2" access cover with O-ring $165.00


602345906 8" × 1/2" access cover with O-ring $177.00


602345907 8" Cover Spare 36" MP Style $147.00

EP-400-VB Extraction pump $80.00

SC-1501L Large cam assembly $41.00

SC-1501S Small cam assembly $41.00

SC-1524B 24" D-ring gasket $62.00



70522502 Cover actuated push drain for below grade EBW 5 gallon spill contaniner $174.00

79

ManwaysModel Description List1114901 Replacement bolt for 810 and 814 monitoring well manways $9.25

1117637 Stainless steel Hex head cap screw for FRC manways $6.75

1127503 Flat stainless steel washer for bolt-down FRC manways $6.25

78044506 42" grey Aramid cover, no holes $1,731.00

78120501 Replacement lift handle assembly $41.00

78120901 Slide action cover replacement key plate $97.00

78133401 18" bolt-down FRP cover for 781-465 bolt-down manway $191.00

78134101 Slide action cover removal handle $154.00

78144801 36" no hole cover, black $895.00

78148201 36" manway slide action cover, black $982.00

78148206 36" manway slide action cover, grey $982.00

78710401 2-way reflective marker I.D., red $21.00

78710402 2-way reflective marker I.D., white $21.00

78920301 Pit box cover $109.00

80810001 8" assembly lid $66.00

80820001 8" manway gasket $12.00

81040101 10" monitoring well lid $81.00

81440101 14" monitoring well lid $92.00

98720101 Pit box cover $192.00

SRC24HRS 24" round finished cover $273.00

SRC36HRS 36" round assembly cover $655.00

SRC38HRS 38" round assembly cover $777.00

SRC38WRS 38" raintight assembly cover $777.00

SRC42WRS 42" raintight assembly cover $1,283.00

SSQC24HS 24" square replacement cover for SSQ2409 manway $285.00

FiberglassModel Description List602133909 42" cover assembly, two spill container openings, one 8" access opening $3,092.00

602166001 Sump shield latch $44.25

602212001 33" sump shield gasket $67.00


602226904 36" watertight sump shield, 2 spill container openings, 1 access opening, no boots $1,166.00

602226909 42" watertight sump shield, 4 spill container openings, no boots $1,402.00

602226910 42" watertight sump shield, 2 spill container openings, 1 access opening, no boots $1,125.00

WTBC-0800 8" stainless steel, #140 band clamp $18.75



80

Aboveground Storage Tank Equipment

Model Description List1127507 Stainless steel flat washer for 709 Warden® $3.50

9006001 S-kit diaphragm for 664 pressure regulator valve $159.00

Suction SystemsModel Description List1103913 Fluorocarbon #2-236 O-ring for 325 product line isolation valve $22.25

32010001 Gasket cap for 320 foot valve $55.75

32010002 Gasket insert for 320 foot valve $55.75

32010401 Gasket with cap for 320 foot valve $128.00

ToolsModel Description List66410901 664 pressure regulator valve intake screen $15.00

81

Lbs. Kg250 Master 486 219 $23.75

500 Master 593 267 $23.00

2500 S. Master 1,478 665 $20.75

250 Master 443 199 $20.00

500 Master 505 227 $19.50

100 Master 435 196 $31.25

250 Master 518 233 $29.75

500 Master 655 295 $29.00

1000 S. Master 965 434 $27.50

1500 S. Master 1,240 558 $27.00

100 Master 410 185 $22.75

250 Master 455 205 $22.75

500 Master 530 239 $21.25

1000 S. Master 715 322 $21.00

1500 S. Master 865 389 $20.00

100 Master 485 218 $34.50

250 Master 655 295 $33.50

500 Master 830 374 $31.50

1000 S. Master 1,355 610 $31.25

100 Master 585 263 $46.75

200 Master 690 311 $45.75

350 Master 848 381 $45.00

700 S. Master 1,250 563 $42.75

100 Master 545 245 $39.50

200 Master 610 275 $37.00

350 Master 708 318 $36.50

700 S. Master 970 437 $35.50

XP-150-SC 1½" secondary

XP-150-D 1½" single wall

XP-175-SC 1¾" secondary contained

XP Pressure and Suction Pipe

Model Description Ft.

XP-100-D 1" single wall

ReelWeight

List

XP-100-SC 1" secondary contained

XP-200-SC 2" secondary contained

XP-200-D 2" single wall

82

Lbs. KgXP-100-MD-250 250 Small 813 369

XP-100-MD-500 500 Standard 1,626 738

XP-100-MDD-250 250 Small 751 340

XP-100-MDD-500 500 Standard 1,501 681

XP-150-MD-250 250 Small 940 426

XP-150-MD-500 500 Standard 1,879 852

XP-150-MDD-250 250 Small 890 404

XP-150-MDD-500 500 Standard 1,779 807

XP-175-MD-250 250 Small 1,011 459

XP-175-MD-500 500 Standard 2,022 917

XP-200-MD-200 200 Master 1,069 485

XP-200-MD-350 350 S. Master 2,083 944

XP-200-MDD-200 200 Master 999 453

XP-200-MDD-350 350 S. Master 1,871 849

Model Description Units ListDUCT-400-100 4" corrugated ducting (for retractability only 100 LF $598.00

DUCT-400-250 4" corrugated ducting (for retractability only 250 LF $1,498.00

DCT-400-F Flexible ducting connector with clamps EA $35.00

XP Marina/Aboveground

Model Description Ft. ReelWeight

List

1" secondary contained inside metallic duct

$38.50

1" single wall inside metallic duct $30.75

1½" secondary contained inside metallic duct

$45.50

1½" single wall inside metallic duct $36.00

1¾" secondary contained inside metallic duct

$48.00

4" Ducting

2" secondary contained inside metallic duct

$72.25

2" single wall inside metallic duct $69.00

83

XP Clamshell Swivel Pipe FittingsBrass SwivelsModel Description ListMS-XP-150-150 Installs on the end of 1½" single/secondary contained XP pipe with 1½" NPT $122.00

MS-XP-175-200 Installs on the end of 1¾" single/secondary contained XP pipe with 2" NPT $158.00

MS-XP-200-200 Installs on the end of 2" single/secondary contained XP pipe with 2" NPT $177.00

Stainless Steel SwivelsModel Description ListMS-XP-150-150SS* Installs on the end of 1.50" single/secondary contained XP pipe with 1½" NPT $231.00

MS-XP-175-200SS* Installs on the end of 1.75" single/secondary contained XP pipe with 2" NPT $261.00

MS-XP-200-200SS* Installs on the end of 2.00" single/secondary contained XP pipe with 2" NPT $322.00*Contact Customer Service for availability and lead times.

XP Clamshell Non-Swivel Pipe FittingsBrass FittingsModel Description ListMN-XP-100-100 Installs on the end of 1" single/secondary contained XP pipe with 1" NPT $101.00

Stainless Steel SwivelsModel Description ListMN-XP-100-100SS* Installs on the end of 1" single/secondary contained XP pipe with 1" NPT $126.00*Contact Customer Service for availability and lead times.

XP Male Swage Swivel Pipe FittingsModel Description ListMS-XP-SW-150150 Installs on the end of 1½" single/secondary contained XP pipe with 1½" NPT $210.00

MS-XP-SW-175200 Installs on the end of 1¾" single/secondary contained XP pipe with 2" NPT $231.00

MS-XP-SW-200200 Installs on the end of 2" single/secondary contained XP pipe with 2" NPT $261.00

XP Clamshell Non-Swivel Tee and Elbow Pipe FittingsModel Description ListTEE-XP-150 1½" XP tee clamshell non-swivel pipe fitting $322.00

ELB-XP-150 1½" XP elbow clamshell non-swivel pipe fitting $259.00

TEE-XP-175 1¾" XP tee clamshell non-swivel pipe fitting $375.00

ELB-XP-175 1¾" XP elbow clamshell non-swivel pipe fitting $303.00

TEE-XP-200 2" XP tee clamshell non-swivel pipe fitting $384.00

ELB-XP-200 2" XP elbow clamshell non-swivel pipe fitting $315.00

84

XP Quick Release Pipe FittingsModel Description ListQRS-XP-150-200 XP quick relase fitting, installs with 1½" XP pipe with 2" flange $216.00

QRS-XP-175-200 XP quick relase fitting, installs with 1¾" XP pipe with 2" flange $229.00

QRS-XP-200-200 XP quick relase fitting, installs with 2" XP pipe with 2" flange $240.00

407031001 2" Short Elbow $141.00

407032001 2" Short Tee $260.00

407082001 Clamp $18.00

407046001 Flourocarbon gasket $8.00

Note: Contact customer service for availability of these parts

End Connections and FittingsModel Description ListGC-150 Galvanized cap, 1½" NPT $19.00

GC-200 Galvanized cap, 2" NPT $20.00

GE90-150 Galvanized elbow, 90º, 1½" NPT $26.00

GE90-200 Galvanized elbow, 90º, 2" NPT $44.00

GE90-215 Galvanized reducing elbow, 90º, 2" NPT × 1½" NPT $30.00

GE90-252 Galvanized reducing elbow, 90º, 2½" NPT × 2" NPT $118.00

GHB-200-150 Galvanized Hex bushing, 2" NPT × 1½" NPT $21.00

GT-150 Galvanized tee, 1½" NPT $27.00

GT-200 Galvanized tee, 2" NPT $47.00

GT-215 Galvanized reducing tee, 2" × 2" × 1½" NPT $55.00

GT-252 Galvanized reducing tee, 2½" × 2½" × 2" NPT $155.00

GU-150 Galvanized union, 1½" NPT $59.00

GU-200 Galvanized union, 2" NPT $51.00

Stainless Steel End Connections and Fittings*Model Description ListSSC-150 Stainless steel cap, 1½" NPT $35.00

SSC-200 Stainless steel cap, 2" NPT $45.00

SSE90-150 Stainless steel elbow, 90º, 1½" NPT $56.00

SSE90-200 Stainless steel elbow, 90º, 2" NPT $77.00

SSSHP-150 Stainless steel square head plug, 1½" NPT $46.00

SST-150 Stainless steel tee, 1½" NPT $80.00

SST-200 Stainless steel tee, 2" NPT $103.00

SSHB-200-150 Stainless steel Hex bushing, 2" NPT × 1½" NPT $55.00

SSU-150 Stainless steel union, 1½" NPT $177.00

SSU-200 Stainless steel union, 2" NPT $177.00

SSRB-150-050 Stainless steel reducing bell 1.5" x .5" NPT $24.00

SSHB-200-050 Stainless steel hex bushing 2" NPT x .5" NPT $58.00

SSHB-150-050 Stainless steel hex bushing 1.5" NPT x .5" NPT $36.00

SSSHP-050 Stainless square hex plug ½" NPT $11.00

*Contact Customer Service for availability and lead times on all stainless steel end connections and fittings.

85

BushingsModel Description ListGHB-200-150 Galvanized Hex bushing, 2" NPT × 1½" NPT $21.00

SSHB-200-150 Stainless steel Hex bushing, 2" NPT × 1½" NPT $55.00

GSHP-150 Galvanized square head plug, 1½" NPT $21.00

SSHB-200-050 Stainless steel hex bushing 2" NPT x .5" NPT $58.00

SSHB-150-050 Stainless steel hex bushing 1.5" NPT x .5" NPT $36.00

GSHP-200 Galvanized square head plug, 2" NPT $29.00

CapsModel Description ListGC-150 Galvanized cap, 1½" NPT $19.00

GC-200 Galvanized cap, 2" NPT $20.00

SSC-150 Stainless steel cap, 1½" NPT $35.00

SSC-200 Stainless steel cap, 2" NPT $45.00

ElbowsModel Description ListGE90-150 Galvanized elbow, 90º, 1½" NPT $26.00

GE90-200 Galvanized elbow, 90º, 2" NPT $44.00

GE90-215 Galvanized reducing elbow, 90º, 2" NPT × 1½" NPT $30.00

GE90-252 Galvanized reducing elbow, 90º, 2½" NPT × 2" NPT $118.00

SSE90-150 Stainless steel elbow, 90º, 1½" NPT $56.00

SSE90-200 Stainless steel elbow, 90º, 2" NPT $77.00

86

PlugsModel Description ListSSSHP-150 Stainless steel square head plug, 1½" NPT $46.00

SSSHP-050 Stainless square hex plug ½" NPT $11.00

TeesModel Description ListGT-150 Galvanized tee, 1½" NPT $27.00

GT-200 Galvanized tee, 2" NPT $47.00

GT-215 Galvanized reducing tee, 2" × 2" × 1½" NPT $55.00

GT-252 Galvanized reducing tee, 2½" × 2½" × 2" NPT $155.00

SST-150 Stainless steel tee, 1½" NPT $80.00

SST-200 Stainless steel tee, 2" NPT $103.00

UnionsModel Description ListGU-150 Galvanized union, 1½" NPT $59.00

GU-200 Galvanized union, 2" NPT $51.00

SSU-150 Stainless steel union, 1½" NPT $177.00

SSU-200 Stainless steel union, 2" NPT $177.00

2" Vent Conversion Box FittingsModel Description ListVNC-200 2" nylon male nipple $51.00

VCF-200 Vent conversion box with 2" nylon nipple and 2" galvanized riser with union $237.00

87

Flexible Entry BootsModel Description ListFEB-050-D Flexible entry boot for ½" electrical conduit $46.00

FEB-050-SC* Flexible entry boot for ¾" electrical conduit $46.00

FEB-075-D Flexible entry boot for ¾" and 1" electrical conduit $46.00

FEB-075-D2 Double sided flexible entry boot for 3/4" and 1" conduit $65.00

FEB-075-SC* Flexible entry boot for 1" electrical conduit $47.00

FEB-100-D Flexible entry boot for XP-100-D $46.00

FEB-100-SC Flexible entry boot for XP-100-SC $46.00




FEB-175-SC Flexible entry boot for XP-175-SC and 2" single wall fiberglass $62.00




FEB-300 Flexible entry boot for 3" single wall fiberglass $89.00

FEB-300-R Flexible entry boot for 3" single wall fiberglass $67.00

FEB-400-R Flexible entry boot for 4" single wall fiberglass $92.00

FEB-400-F Flexible entry boot for 4" double wall pipe $92.00

Ducted Flexible Entry BootsModel Description ListDEB-150-D Ducted entry boot for XP-150-D $80.00

DEB-150-SC Ducted entry boot for XP-150-SC $80.00

DEB-175-D Ducted entry boot for XP-175-D $81.00


DEB-200-D Ducted entry boot for XP-200-D $85.00


DEB-250-SC Ducted entry boot for P-250-SC $94.00

Air Testable Flexible Entry BoothModel Description ListDEB-150-DA Air testable ducted entry boot for XP-150-D $83.00

DEB-150-SCA Air testable ducted entry boot for XP-150-SC $82.00

DEB-175-DA Air testable ducted entry boot for XP-175-D $83.00

DEB-175-SCA Air testable ducted entry boot for XP-175-SC $85.00

DEB-200-DA Air testable ducted entry boot for XP-200-D $126.00

DEB-252-DA Air testable ducted entry boot for XP-200-SC and P-250-D $137.00

* Limited Availability / Please contact Customer Servce for availability

88

Flexible Double Entry BootsModel Description ListFDB-075-D Flexible double boot for ¾" electrical conduit $102.00

FDB-075-SC Flexible double boot for P-075-SC $102.00

FDB-100-D Flexible double boot for XP-100-D or 1" electrical conduit $102.00

FDB-100-SC Flexible double boot for XP-100-SC $102.00

Ducted Flexible Double Entry BootsModel Description ListDDB-075-D Ducted double boot for ¾" electrical conduit $123.00

DDB-075-SC Ducted double boot for P-075-SC $123.00

DDB-100-D Ducted double boot for XP-100-D or 1" electrical conduit $123.00

DDB-100-SC Ducted double boot for XP-100-SC $123.00

Flexible Bulkhead BootsModel Description ListFBB-075-D* Flexible bulkhead boot for P-075-D, ¾" and 1" electrical conduit $57.00

FBB-150-SC Flexible bulkhead boot for XP-150-SC $71.00

Model Description ListDBB-150-SC Ducted bulkhead boot for XP-150-SC $113.00

DBB-200-SC Ducted bulkhead boot for XP-200-SC $113.00

MD-Series Flexible Entry BootsModel Description ListFEB-075-MDD Flexible entry boot for P-075-MD $88.00

FEB-075-MD Flexible entry boot for P-075-MD $85.00

FEB-100-MDD Flexible entry boot for XP-100-MDD $92.00

FEB-100-MD Flexible entry boot for XP-100-MD $88.00







* Limited Availability / Please contact Customer Servce for availability

89

Rigid Entry Boots- XP PipeModel Description ListREB-150-SC 1½" rigid entry boot for flat sump surfaces $130.00

REB-175-SC 1¾" rigid entry boot for flat sump surfaces $130.00

REB-200-SC 2" rigid entry boot for flat sump surfaces $130.00

REB-R-150-SC 1½" rigid entry boot for round sump surfaces $147.00

REB-R-175-SC 1¾" rigid entry boot for round sump surfaces $147.00

REB-R-200-SC 2" rigid entry boot for round sump surfaces $147.00

RDEB-150-SC 1½" ducted rigid entry boot for flat sump surfaces $135.00

RDEB-175-SC 1¾ ducted rigid entry boot for flat sump surfaces $135.00

RDEB-200-SC 2" ducted rigid entry boot for flat sump surfaces $135.00

RDEB-R-150-SC 1½" ducted rigid entry boot for round sump surfaces $179.00

RDEB-R-175-SC 1¾ ducted rigid entry boot for round sump surfaces $179.00

RDEB-R-200-SC 2" ducted rigid entry boot for round sump surfaces $179.00

408051001 1½" Pipe Seal $22.00

408052001 1¾" Pipe Seal $22.00

408042001 2" Pipe Seal $22.00

408055001 1½" Pipe snap body insert $16.00

408056001 1¾" pipe snap body insert $16.00

408058001 1½" compression nut insert $16.00

408059001 1¾" compression nut insert $16.00

408069001* Plastic adapter for curved sump $24.00

*Used to convert a flat sump surface rigid entry boot into a round sump surface rigid entry boot.

Rigid Entry Boots- Electrical ConduitModel Description ListREB-C-0075 Rigid entry boot ¾" conduit/flat surface $157.00

REB-C-0100 Rigid entry boot 1" conduit/flat surface $157.00

REB-C-R-0075 Rigid entry boot ¾" conduit/round surface $167.00

REB-C-R-0100 Rigid entry boot 1" conduit/round surface $167.00

408066001 ¾" Conduit Seal (Replacement) $10.00

408066002 1" Conduit Seal (Replacement) $10.00

408070001 Clamping Seal- Flat (Replacement) $12.00

408072001 Clamping Seal- Round (Replacement) $15.00

408073001* Plastic adapter for curved sump $24.00

Fusion Entry BootsModel Description ListFWEB-150-SC Flexible entry boot 1.5″ SC Pipe $140.00

FWEB-175-SC Flexible entry boot 1.75″ SC Pipe $140.00

FWEB-200-SC Flexible entry boot 2.0″ SC Pipe $146.00

*Used to convert a flat sump surface rigid entry boot into a round sump surface rigid entry boot.

90

Split Test BootsModel Description ListSPTB-150 Split test boot for XP-150-SC double wall pipe $89.00

SPTB-175 Split test boot for XP-175-SC double wall pipe $93.00

SPTB-200 Split test boot for XP-200-SC double wall pipe $96.00

Clamshell Secondary Test BootsModel Description ListSTB-100 Secondary test boot for XP-100-SC pipe $22.00

STB-150 Secondary test boot for XP-150-SC pipe $22.00



91

Grade Level Transition Sleeve™Model Description ListTSL-005 Transition sleeve (top and bottom boot required, sold separately) $398.00

TST-100-D Transition sleeve top flexible entry boot, 1" steel pipe $95.00

TSB-100-D Transition sleeve bottom flexible entry boot for XP-100-D or 1" conduit $111.00TSB-100-SC Transition sleeve bottom flexible entry boot for XP-100-SC $111.00Note: The transition sleeve along with the top and bottom entry boot should be ordered separately.

Wall Transition SleeveModel Description ListWTS-400 Wall transition sleeve (ducted entry boot required, sold separately) $34.00

92

Below Grade Transition Tank SumpsModel Description ListTS-2430 Transition sump, shallow burial, 24" base, fits under a 30" manway $461.00

TS-3630 Tank sump, shallow burial, 36" base, fits under a 30" manway $939.00

TS-4230 Tank sump, medium burial, 42" base, fits under a 30" manway $982.00

TS-KIT TS-3630/4230 retro fit kit, replacement lid assembly for screw-on polyethylene lids $764.00999-855-55 Replacement gasket $29.00

Below Grade Intermediate Piping SumpsModel Description ListIPS-2424 Intermediate piping sump, 24" × 24", fits under a 24" manway $757.00

IPS-3636 Intermediate piping sump, 36" × 36", fits under a 36" manway $828.00

999-855-54 Replacement gasket $56.00

73510102 Replacement Access cover $122.00

Grade Level Transition SumpModel Description ListAST-2922 Aboveground storage tank transition sump $1,158.00999-855-53 Replacement gasket $43.00252-029-23 Replacement AST-2922 lid, grey $344.00

IP-400-B Inspection replacement port, FEB style with replacement well cap $82.00

4542 Series One-Piece Tank SumpsModel Description ListTSD-4542 Tank sump, deep burial, 45" base, fits 42" manway $1,297.00

TSM-4542 Tank sump, medium burial, 45" base, fits 42" manway $917.00

TSS-4542 Tank sump, shallow burial, 45" base, fits 42" manway $914.00

260-042-09 TSM-4542 sump lid replacement $258.00

MA-22 Manway adapter, 22" $817.00

MA-24 Manway adapter, 24" $1,049.00

IP-400 Inspection port $69.00

IP-400-B Inspection port, FEP style with well cap $82.00

4736 Series One-Piece Tank SumpsModel Description ListTSD-4736 Tank sump, deep burial, 47" base, fits 36" manway $1,070.00

TSM-4736 Tank sump, medium burial, 47" base, fits 36" manway $898.00

TSS-4736 Tank sump, shallow burial, 47" base, fits 36" manway $829.00

260-036-08 TSM-4736 sump lid replacement $172.00

MA-22 Manway adapter, 22" $817.00

MA-24 Manway adapter, 24" $1,049.00

IP-400 Inspection port $69.00

IP-400-B Inspection port, FEP style with well cap $82.00

93

Medium* Deep*T(X)A4236-0/0-RC-S Single 42 36 2 No $2,641.00 $3,190.00

T(X)A4836-0/0-RC-S Single 48 36 2 No $3,012.00 $3,797.00

Note: Seam kits not included. See bottom of page for part number and pricing.

*Overall height. Note: For (X) Please insert “M/D” in part number use “M” for medium or “D” for deep when ordering.

42" Single and Double Wall Octagonal Turbine Sumps

Shallow* Medium* Deep*T(X)4236-0/0-OC-S Single 42 36 2 No 39 N/A $2,412.00 $2,670.00

T(X)4236-0/0-OB-S Single 42 36 1 Yes 39 N/A $3,099.00 $3,336.00

TSS-4236-0/0-OB-S Single 48 36 0 Yes 39 $2,402.00 N/A N/A

T(X)4236-0/0-OC-H Double 42 36 4 No 39 N/A $6,379.00 $6,936.00

T(X)4236-0/0-OC-V Double 42 36 4 No 39 N/A $6,233.00 $7,083.00



48" Single and Double Wall Octagonal Turbine Sumps

Medium* Deep*T(X)A4836-0/0-OC-S Single 48 36 3 No 42 $2,781.00 $3,226.00

T(X)A4836-0/0-OB-S Single 48 36 2 Yes 42 $3,561.00 $4,078.00

T(X)4836-0/0-OC-H Double 48 36 4 No 42 $6,794.00 $8,326.00

T(X)4836-0/0-OC-V Double 48 36 4 No 42 $6,823.00 $8,261.00



Fiberglass Seam Adhesive KitModel ListFG-SEAMKIT $223.00Note: Double wall applications may require two seam kits per seam. Fiberglass orders cannot be cancelled.

Please contact customer service for lead times and availability for ALL fiberglass products. Fiberglass orders cannot be cancelled.

Riser Dia.

BottomList

Model Wall Type Octagonal Base Dia.

Min. Manway

Size

Seam Kits Bottom

Seam Kits


List

42" and 48" Single Wall Cylindrical Turbine Sumps

Model Wall Type Riser Base Dia.

Min. Manway

Size


Descriptiondouble wall.

Bottom Riser Dia.List

Model Wall Type Octagonal Base Dia.

Min. Manway

SizeSeam Kits

94

30" Fiberglass Sump Shield PackagesModel ListTSS-4236 $1,409.00

TSS-4836 $1,646.00

TSS-XS36 $1,498.00

Note: Seak kit not included. Package includes watertight sump shield and riser reducer

Fiberglass Replacement PartsModel ListTSS-36 36" Watertight sump shield $771.00



602329001 Sump shield /keeper $7.00

602331001 Rubber Pull latch $16.00

602330901 Bracket $11.00

602221902 Adaptor 42/36 $591.00

602221904 Adaptor 42/42 $619.00

602221908 Adaptor 48" $683.00

602226906 Adaptor 42" WTC $979.00


Description30" opening, 42" riser

30" opening, 48" riser


30" opening, Xerxes 33" diameter riser

Description

95

Large Mouth Poly Dispenser Sumps

Medium DeepLM(X)-1410 Large mouth poly sump with 14"x10" top frame $598.00 $657.00LM(X)-1913-T Large mouth poly sump with 19"x13" top frame $681.00 $730.00LM(X)-2010 Large mouth poly sump with 20"x10" top frame $629.00 $705.00LM(X)-2018 Large mouth poly sump with 20"x18" top frame $664.00 $720.00

LM(X)-2313-T Large mouth poly sump with 23"x13" top frame $744.00 $836.00

LM(X)-2407 Large mouth poly sump with 24"x7" top frame $673.00 $775.00





LM(X)-3617 Large mouth poly sump with 36"x17" top frame (Encore™ conduitless) $821.00 $889.00

LMM-3617-DEF Large mouth poly sump 36x17 top frame with DEF frame $1,935.00 N/A

LM(X)-3914-36-W Large mouth poly sump w/ 39"x14" top frame (Ovation™ conduitless) $873.00 $939.00LM(X)-3914 Large mouth poly sump with 39"x14" top frame $821.00 $934.00LM(X)-4018 Large mouth poly sump with 40"x18" top frame $821.00 $925.00LM(X)-4111 Large mouth poly sump with 41"x11" top frame $821.00 $939.00LM(X)-4115 Large mouth poly sump with 41"x15" top frame $821.00 $952.0043605002 $13.0043607502 $9.0043610002 $9.00

Note: For (X) Please insert "M/D" in part number use “M” for medium or “D” for deep when ordering.

Large Mouth Poly Dispenser Sump Tops

Model Description Base Size - LB(X) List

LMT-1410 Large mouth sump top 14"x10" 2400 $318.00

LMT-1913-T Large mouth sump top 19"x13" 2400 $390.00



LMT-2313-T Large mouth sump top 23"x13" 3600 $414.00






LMT-3617-36 Large mouth sump top 36"x17" 3600 $385.00

LMT-3914-36-W Large mouth sump top 39"x14" 3600 $520.00





ListModel Description

Ovation™ is a trademark of Dresser Inc. Encore™ is a trademark of Gilbarco Inc.

1/2" grommets for conduitless sump

1" grommets for conduitless sump

3/4" grommets for conduitless sump

96

Large Mouth Poly Dispenser Sump BasesModel Description ListLBM-2400 Large mouth 24" sump base - medium $315.00

LBM-3600 Large mouth 36" sump base - medium $390.00

LBM-4800 Large mouth 48" sump base - medium $508.00

LBD-2400 Large mouth 24" sump base - deep $374.00



Single and Double Wall Fiberglass Large Mouth Dispenser Sumps2400 Series

Single DoubleLMM-1410-X Fiberglass dispenser sump, 14"x10" $1,247.00 $2,256.00

LMM-1913-T-X Fiberglass dispenser sump, 19"x13" $1,303.00 $2,256.00

LMM-2010-X Fiberglass dispenser sump, 20"x10" $1,247.00 $2,256.00



HM-KIT Hydrostatic monitoring system for dispenser sumps $204.00

602-284-004 Drop down frame 2400 series $254.00Note: Fiberglass models include base and top.

Note: For (X) Please insert “S/D” in part number use “S” for single wall or “D” for double wall.

3600 Series

Single DoubleLMM-2313-T-X Fiberglass dispenser sump, 23"x13" $1,472.00 $2,531.00






LMM-3914-36-W-X Fiberglass dispenser sump, 39"x14" $1,642.00 $2,905.00



602-270-004 Drop down frame 3600 series $302.00Note: Fiberglass models include base and top.


List

ListDescriptionModel

DescriptionModel



97

4800 Series

Single DoubleLMM-3610-X Fiberglass dispenser sump, 36"x10" $1,575.00 $2,893.00







602-271-004 Drop down frame 4800 series $309.00

Note: Fiberglass models include base and top.


Counduitless Entry Fiberglass SumpModel Description List

DHW-3617 36" x 17" fiberglass dispenser sump, single-wall, with conduitless entry frame

$1,399.00

Classic Dispenser Pan SumpsModel Description ListDP-1816 Dispenser pan, 13¾" × 11¼" $384.00

DP-2014 Dispenser pan, 16½" × 10½" $393.00

DP-2816 Dispenser pan, 23" × 11¾" $419.00

DP-4721 Dispenser pan, 42" × 16" $518.00


DescriptionModelList

98

Model Description ListTFA-400-II Tank fitting adapter generation II, 4" NPT $227.00

TFA-600 Tank fitting adapter, 6" NPT $908.00

411-105-02 Compression plate for TFA-400-II (replacement) $72.00

420-200-02 Plate washer TFA-400-II (replacement) $22.00

446-100-02 Gasket for TFA-400-II $24.00

Model Description ListMA-22 22" tank manway adapter $817.00

MA-24 24" tank manway adapter $1,049.00

Model Description ListSBK-1 Stabilizer bar kit 1 $69.00

SBK-2 Stabilizer bar kit 2 $63.00



Tank Fitting Adapters

Tank Manway Adapters

Stabilizer Bar Kits

99

Model Description ListBPT-200 By-Pass Tube $24.00

BOS-103 Bostik 1100, 10.3 ounce tube $26.00

BTT-004 Bulkhead tightening tool for 4 stud bulkhead boots $70.00

DBT-100 Deburring tool $31.00

DWC-XP-100 Double wall cutting tool, 1" $305.00

DWC-XP-150 Double wall cutting tool, 1½ $305.00

DWC-XP-175 Double wall cutting tool, 1¾" $319.00

DWC-XP-200 Double wall cutting tool, 2" $319.00

DWC-XP-TOOL DWC Handle & (5)Blades $182.00

SDT-010 Steel drill template for 4, 8 and 10 stud entry boots $59.00

SLP-1000 Sump lid puller for TS-4542 and TS-4736 snap-on lid $23.00

TRK-200 Air test regulator for APT secondary contained piping $150.00

STK-1 Single line secondary test system $71.00STK-2 Dual line secondary test system $108.00

Model Description ListSWK-150 Swage tool kit, 1½" $227.00

SWK-175 Swage tool kit, 1¾" $267.00

SWK-200 Swage tool kit, 2" $305.00

Installation Tools

Swage Machine

100

UPP Semi-Rigid Pipework SystemsUPP 1½" Secondary Contained Pipework SystemModel Description List001-063-050-028 PSE 1 ½" double wall pipe, 28' stick $434.00

001-063-050-033 PSE 1 ½" double wall pipe, 33' stick $511.50

001-063-050-165 PSE 1 ½" double wall pipe, 165' coil $2,557.50

02-50-U 1 ½" primary welding coupler $21.00

02-050-L-U 1 ½" primary welding coupler, long $27.00

03-050-EIF-U 1 ½" primary electrofusion 90° elbow fitting $47.00

03-050-L 1 ½" primary plain 90° elbow fitting $19.00

04-050-EIF-U 1 ½" primary electrofusion 45° elbow fitting $47.00

04-050-L 1 ½" primary plain 45° elbow fitting $19.00

08-050-EIF-U 1 ½" single wall electrofusion tee fitting $55.00

08-050-L 1 ½" primary plain tee fitting $30.00

09-063-050-L 2" x 1 ½" primary plain reducer fitting $23.00

10-050-L 1 ½" primary plug $17.00

02-63SC-U 1 ½" secondary welding coupler $12.00

49-063-050-U 1 ½" secondary electrofusion reducer fitting $72.00

49-063-050TP-U 1 ½" secondary electrofusion reducer fitting with test port $72.00

49-110-063SC-U 4" x 1 ½" secondary electrofusion reducer fitting $62.00

91-050 NPT-U 1 ½" (pipe) x 1 ½" NPT male threaded termination fitting $79.00

91-050 SS NPT-U 1 ½" (pipe) x 1 ½" NPT male threaded termination fitting, stainless steel $135.00

92-063-1 NPT-U 2" (pipe) x 1 ½" NPT male threaded termination fitting $80.00

91-063-NPT-U 2" (pipe) x 2" NPT male threaded termination fitting $79.00

92-050 NPT-U 1 ½" (pipe) x 1 ½" NPT female threaded termination fitting $79.00

92-063-1 NPT-U 2" (pipe) x 1 ½" NPT female threaded termination fitting $80.00

92-050 UF NPT-U 1 ½" (pipe) x 1 ½" NPT union adapter termination fitting $87.00

11.50G 1 ½" gasket $9.00

HEX 2 2" NPT X 1 ½" NPT hex adapter $30.00

303-063-EIF-U 1 ½" double wall / 2" single wall electrofusion entry boot $124.00

304-110-063-TP 1 ½" double wall ducted entry boot with ducting test port $179.00

G3-063-050-U SC 1 /2" Gemini 90° Elbow $139.00

G4-063-050-U SC 1 1/2" Gemini 45° Elbow OR SC 1 1/2" Gemini Inline Joint $139.00

G8-063-050-U SC 1 ½" Gemini Tee $280.00

101

UPP 2" Primary Pipework SystemModel Description List001-063-019VE 2" single wall pipe, 19' stick $204.25

02-63-U 2" primary welding coupler $31.00

02-063-L-U 2" primary welding coupler, long $36.00

03-063-EIF-U 2" primary electrofusion 90° elbow fitting $47.00

03-063-L 2" primary plain 90° elbow fitting $19.00


08-063-EIF-U 2" single wall electrofusion tee fitting $55.00

08-063-L 2" primary plain tee fitting $42.00

09-090-063-EIF-U 3" x 2" primary electrofusion reducer fitting $57.00

09-090-063-L-U 3" x 2" primary plain reducer fitting $28.00

09-110-063-L-U 4" x 2" primary plain reducer fitting $30.00

08-090-063-U 3" x 3" x 2" primary plain reducing tee $80.00

10-063-L-U 2" primary plug $17.00

91-063 NPT-U 2" (pipe) x 2" NPT male threaded termination fitting $79.00

91-063 SS NPT-U 2" (pipe) x 2" NPT male threaded termination fitting, stainless steel $184.00

91-063-1 NPT-U 2" (pipe) x 1 ½" NPT male threaded termination fitting, stainless steel $79.00

92-063 NPT-U 2" (pipe) x 2" NPT female threaded termination fitting $79.00

11.50 NPT 2" (pipe) x 2" NPT female threaded termination fitting w/o hex $79.00

90-063 QL-U 2" (pipe) x 2" quick release termination fitting $79.00

92-063 UF NPT-U 2" (pipe) x 2" NPT union adapter termination fitting $126.00

11.63G 2" gasket $9.00

303-063-EIF-U 1 1/2" double wall/ 2" single wall electrofusion entry boot $124.00FEB-075-M 2" fiberglass entry boot $303.00

102

UPP 2" Secondary Contained Pipework SystemModel Description List001-075-063-028 PSE 2" double wall pipe, 28' stick $560.00

001-075-063-033 PSE 2" double wall pipe, 33' stick $660.00

001-075-063-038 PSE 2" double wall pipe, 38' stick $760.00

001-075-063-100 PSE 2" double wall pipe, 100' coil $2,000.00

001-075-063-165 PSE 2" double wall pipe, 165' coil $3,300.00


02-75SC-U 2" Secondary Weld Coupling $14.00

02-063-L-U 2" primary welding coupler, long $36.00




49-075-063-1-U 2" secondary electrofusion reducer fitting $73.00

49-075-063TP1-U 2" secondary electrofusion reducer fitting with test port $73.00

03-050-L 4" x 2" secondary electrofusion reducer fitting $19.00

09-110-75SC-U 4" x 2" secondary plain reducer fitting $15.00

10-075-SC 2" secondary plug $8.00



303-075-EIF-U 2" double wall electrofusion entry boot $124.00

304-110-075-TP 2" double wall ducted entry boot with ducting test port $179.00

G3-075-063-U SC 2" Gemini 90° Elbow $152.00

G4-075-063-U SC 2" Gemini 45° Elbow OR SC 2" Gemini Inline Elbow $152.00

G8-075-063-U SC 2" Gemini Tee $375.00

103

UPP 3" Primary Pipework SystemModel Description List001-090-019VE 3" single wall vent pipe, 19' stick $318.25



03-090-L 3" primary plain 90° elbow fitting $36.00



08-090-L-U 3" primary plain tee fitting $109.00

09-110-090EIF-U 4" x 3" primary electrofusion reducer fitting $66.00

10-090-L-U 3" primary plug $21.00

03-090-LS-4-U 3" lined primary 90° elbow fitting $222.00



90-090 QL-U 3" (pipe) x 3" quick release termination fitting $79.00

304-110-090-U 3" electrofusion entry boot $177.00

UPP 3" Secondary Contained Pipework SystemModel Description List001-110-090-019PSE 3" double wall pipe, 19' stick $617.50


02-110SC-U 3" secondary welding coupler $14.00




49-110-090-U 4" x 3" secondary electrofusion reducer fitting $159.00

49-110-090TP-U 4" x 3" secondary electrofusion reducer fitting with test port $274.00


91-090-SS NPT-U 3" (pipe) x 3" NPT male threaded termination fitting, stainless steel $260.00


10-090-L-U 3" primary plug $21.00304-110-090-U 3" double wall electrofusion entry boot with integrated termination fitting $177.00

304-110-090TP-U 3" double wall electrofusion entry boot with integrated termination fitting and test port $197.00


G4-110-090-U SC 3" Gemini 45° Elbow OR SC 3" Gemini Inline Joint $177.00

G8-110-090-U SC 3" Gemini Tee $388.00FEB-110-M 3" fiberglass entry boot 380.00$

104

UPP 4" Secondary Contained Pipework SystemModel Description List001-125-110-019PSE 4" double wall pipe, 19' stick $1,216.00





04-110-LS-4-U 4" primary plain elbow 45° fitting $193.00


10-110-L-U 4" primary plug $21.00

03.110(SC) 4" secondary 90° elbow fitting $36.00


04-110-LS-4-U 4" lined primary 45° elbow fitting $193.00

08.110(SC) 4" secondary tee fitting $48.00

08-110-L-U 4" primary tee fitting $201.00

49-110-075SC-U 4" X 2" Weld Reducer $62.00



09.160.110(SC) 6" x 4" secondary plain reducer fitting $25.00

10.110(SC) 4" secondary plug $51.00



FEB-S-125 4" Fiberglass Entry Fitting $359.00305-125-110-U 4" double wall electrofusion entry boot with integrated termination fitting $211.00305-125-110TP-U 4" double wall electrofusion entry boot with integrated termination fitting and test pot $214.00


G4-125-110-U SC 4" Gemini 45° Elbow OR SC 4" Gemini Inline Joint $313.00

UPP 6" Secondary Contained Pipework SystemModel Description List02-160SC-U 6" secondary welding coupler $23.00



08.160(SC) 6" secondary tee fitting $72.00

09.200.160(SC) 8" x 6" secondary plain reducer fitting $526.00

UPP 4" Duct SystemModel Description ListDUCT-400-100 4" flexible ducting, Blue fusion (100' coil) $598.00

DUCT-400-250 4" flexible ducting, Blue fusion (250' coil) $1,498.00



10.125(SC) 5" secondary plug $36.00



105

Dispenser SumpsModel Description ListDS3617 ENCORE Encore™ dispenser sump with 36” x 17” top frame $595.00

SBK-3 Stabilizer bar kit for Encore™ dispenser sump $73.00

DS3915 OVATION Wayne™ and Ovation™ dispenser sump with 39” x 15” top frame $599.00

DS-SB15.1 OVATION Stabilizer bar kit for Wayne™ and Ovation™ dispenser sump $63.00

SBK-25 Stabilizer bar kit for Wayne™ and Ovation™ dispenser sump $69.00Wayne™ is a trademark of Dresser Equipment Group Inc. Ovation™ is a trademark of Dresser Inc.Encore™ is a trademark of Gilbarco Inc.

106

230v EF1 Handheld Electrofusion welderModel Description ListEFI-230V 230v EF1 handheld electrofusion welder $2,108.00

EF1-PC 4mm Spare single wall (primary) welding cable (orange) $244.00

EW8-SC 2MM Spare double wall (secondary) welding cable $245.00

EF1-BC 4mm* Spare jumper welding cable (red) $159.00

*Used to weld a series of single wall (primary) fittings.

110v EF1 Electrofusion welderModel Description ListEF1-110V-A 110v EF1 electrofusion welder $4,471.00

EF1-PC 4mm Spare single wall (primary) welding cable (orange) $244.00

EF1-SC 2mm Spare double wall (secondary) welding cable (green) $245.00

EF1-BC 4mm* Spare jumper welding cable (red) $159.00

*Used to weld a series of single wall (primary) fittings.

Pipe CutterModel Description ListP.CUT 1 ½” to 5” pipe cutter, medium $712.00

P.CUT MED 4” to 6” pipe cutter, large $794.00

Adjustable Rotary ScraperModel Description ListSCR-025-110 1” to 4” pipe adjustable rotary scraper $1,969.00

SCR-090-225 3” to 9” pipe adjustable rotary scraper $4,631.00

SCR-BLADE-025-225 Spare blades for adjustable rotary scraper $216.00

Handheld ScraperModel Description ListSCR.HAR Handheld scraper $21.00

SCR.HAR(B) Spare blades for handheld scraper $18.00

Wooden MalletModel Description ListMAL1 Wooden mallet $80.00

UPP Pipe ClampsModel Description ListCLAMP (S) Straight clamp for straight joints (1” to 4” pipe) $223.00

CLAMP (A) Angled clamp for straight and elbow joints (1” to 4” pipe) $312.00

107

UPP Electrofusion Entry Boot ClampsModel Description List302-CLAMP Clamp for 302 electrofusion entry boot (orange) $105.00

303-CLAMP Clamp for 303 electrofusion entry boot (blue) $134.00

304-CLAMP Clamp for 304-110-090 electrofusion entry booth (yellow) $164.00

UPP Holes SawsModel Description ListMAN1 Mandrel (fits all hole saws) $74.00

HS3 4” hole saw for 303-063 and 303-075 electrofusion entry boots $121.00

HS075 4 1/8” hole saw for FEB-0-075 fiberglass entry boots $96.00

HS5 5 ½” hole saw for FEB-D-110-1 fiberglass entry boots $193.00

HS6 5 5/16” hole saw for 305 electrofusion entry boots $341.00

F.Driver Driver tool $85.00

CW1 Cutting wheel $57.00

Towing HeadModel Description ListTH50-SDR8 1 ½” single wall pipe towing head $547.00

TH63 2” single wall pipe towing head $514.00

TH63SC-SDR8 1 ½” double wall pipe towing head $745.00

TH75SC 2” double wall pipe towing head $822.00

Fiberglass Entry Boot Tools and AccessoriesModel Description ListFEB-110-TOOL* Tool to tighten 3” fiberglass entry boot $36.00

E32-2014-50 Epoxy cartridge (50ml) $103.00

E32 GUN Epoxy cartridge gun $144.00

FG-SEAMKIT Fiberglass seam kit $223.00

EMERY Emery cloth for fiberglass entry booth sump surface preparation (50 meter lengths) $130.00

*Two tools required for tightening.

UPP Pipe and Fitting MarkersModel Description ListCHINA Pencils for marking fittings (box of 12) $36.00

108

UPP Consumables KitModel Description List

408005901UPP Consumables Includes: (1) pound of lint-free rags, (2) markers, (2) one quart spray bottle, (1) box of nitrile gloves, (2) sharpie silver markers, (1) sheet emery cloth, (2) paint scrapers

$157.00

Step Up TransformerModel Description List408032001 Step up transformer $229.00

UPP Essentials Tool KitModel Description List

408033901UPP Essentials Tool Kit includes: (1) angled clamp, (1) straight clamp, (4) 303 entry boot clamps, (1) consumables kit, (1) pipe cutter, (1) rotary scraper, (1) EFI-230v handheld welder, (1) step up transformer

$5,588.00

UPP Tools for 90 Series Termination Fittings Model Description List91-050-TOOL Plate Spanner tool for use with ½" male 90 Series termination fittings $54.00

92-050-TOOL Plate Spanner tool for use with ½" female 90 Series termination fittings $54.00

91-063-TOOL Plate Spanner tool for use with 2" male 90 Series termination fittings $54.00

92-063-TOOL Plate Spanner tool for use with 2" female 90 Series termination fittings $54.00

MiscellaneousModel Description ListTPL Test port w/ long valve ( Contact Customer Service for availability) $42.00

LDT60-1 Leak Detector Tube, 24" $36.00

D/TAPE Detector Tape 100m $485.00

DN50/2 Gasket / Bolt Kit DN50 $15.00

Flange PartsModel Description List05-063-L Stub Flange, 63mm $22.00

05-090-L Stub Flange, 90mm $41.00

07.63 Gasket , 63mm $22.00

07.90 Gasket, 90mm $15.00

109

9961 Clean Air SeparatorModel Description List

9961Vertical clean air separator, includes breather assembly, 9466G float check, locking ball valves, locks and keys $8,002.25

9961H Horizontal clean air separator, includes breather assembly, 9466G float check, locking $8,002.25

9948 Breather assembly $123.25

996123 1" ball valve (4 per CAS) $74.25

996124 Brass lock for ball valve (includes key) (4 per CAS) $27.25

996125 Keys for brass lock $15.00

9466G Float Check (for use with CAS only) $170.50

9943 Replacement Bladder for Clean Air Separator $499.25

110

Model Description ListVP1000M Gasboy™ 9800 Series - Non-Vapor Ready to Healy $2,733.75

Z081H hardware kit $7.25Z081E electrical kit $284.25Z081V vapor kit $262.00VP1000-5 vacuum pump $1,805.751374A MC100-1 interface module with harness $391.75

VP1000N Dresser Wayne™ Harmony™ Series - Balance to Healy $2,488.50Z078H hardware kit $5.75Z078E electrical kit $101.25Z078V vapor kit $202.25VP1000-5 vacuum pump $1,805.751365A MC100-1 interface module with harness $391.75

VP1000P Dresser Wayne™ Ovation™ Series - Balance or WayneVAC to Healy $2,894.50Z079H hardware kit $58.00Z079E electrical kit $430.50Z079V vapor kit $246.25VP1000-5 vacuum pump $1,805.751365A MC100-1 interface module with harness $391.75

VP1000Q Dresser Wayne™ Harmony Series - WayneVAC to Healy $2,556.50Z080H hardware kit $7.25Z080E electrical kit $101.25Z080V vapor kit $271.75VP1000-5 vacuum pump $1,805.751365A MC100-1 interface module with harness $391.75

VP1000R Gilbarco™ Encore™ 300, 500 or 700 Series - Balance to Healy $2,725.75Z082H hardware kit $30.25Z082E electrical kit $377.00Z082V vapor kit $151.25VP1000-5 vacuum pump $1,805.751373A MC100-1 interface module with harness, $391.75

VP1000S Gilbarco™ Encore™ 300 or 500 Series - VaporVAC® to Healy $2,772.50Z082H hardware kit $30.25Z082E electrical kit $377.00Z083V vapor kit $199.75VP1000-5 vacuum pump $1,805.751373A MC100-1 interface module with harness, $391.75


Includes:

VP1000 Dispenser-Mounted Vacuum Source Kits

Includes:

Includes:

Includes:

Includes:

Includes:

Bennett® is a registered trademark of Bennett Pump Company. Wayne™ is a trademark of Dresser Equipment Group Inc.

Ovation™, Harmony™, Roots™ and Vista™ are trademarks of Dresser Inc.

Gasboy™, Gilbarco™, Encore™, G-Site™ and Quantum™ are trademarks of Gilbarco Inc.

111

Model Description ListVP1000T Dresser Wayne™ 3 Vista™ or 4 Vista™ Series - Balance to Healy $2,738.00

Z084H hardware kit $7.25

Z084E electrical kit $342.75

Z084V vapor kit $220.75

VP1000-5 vacuum pump $1,805.75

1365A MC100-1 interface module with harness $391.75

VP1000V Dresser Wayne™ 1 Vista™ or 2 Vista™ blenders only - Balance to Healy $2,738.00

Z084H hardware kit $7.25

Z084E electrical kit $342.75

Z084V vapor kit $220.75

VP1000-5 vacuum pump $1,805.75

1363A MC100-1 interface module with harness, $391.75

Vista™ is a trademark of Dresser Inc. Wayne™ is a trademark of Dresser Equipment Group Inc.


VP1000A

For use with all dispenser types, use if a model-specific VP1000D-V is not available. Includes VP1000-5 vacuum pump, 1360A interface module and 1404 universal hardware/mounting kit.

$2,384.50

VP1000D

Gilbarco™ 300 blender dispensers only (early model AC solenoid valves, pre-April 2003). Includes VP1000-5 vacuum pump, 1368A interface module with harness an 1404 universal hardware/mounting kit.

$2,451.25

VP1000E International only, VP1000-220, 1380A and 1404 $2,574.00

VP1000GWayne™ DL non-blender dispensers only. Includes VP1000-5 vacuum pump, 1354A interface module with harness and 1404 universal hardware/mounting kit. $2,451.25

VP1000H

Tokheim™ Premier™ C blender dispensers with 24 VDC solenoids only. Includes VP1000-5 vacuum pump, 1362A interface module with harness and 1404 universal hardware/mounting kit.

$2,451.25

VP1000J

Tokheim™ earlier-series blender dispenser with AC and DC solenoids. Includes VP1000-5 vacuum pump, 1372A interface module with harness and 1404 universal hardware/mounting kit.

$2,451.25


Z070E Electrical installation kit for VP1000 Series vacuum source, for use with VP1000A-J $292.50

Z071VVapor piping installation kit for VP1000 Series vacuum source, for use with VP1000A-J

$261.25

Z069E International only, 220V electrical installation kit for VP1000E $292.50

Includes:

Includes:

VP1000 Dispenser-Mounted Vacuum Source Kits Continued

VP1000 Dispenser Mounted Vacuum Source Kits (Non-Inclusive)

Universal Vapor and Electrical Kits


Wayne™ is a trademark of Dresser Equipment Group Inc. Tokheim™ and Premier™ are trademarks of Tokheim Holding B.V.

112


1316 6" potted conduit assembly $113.50

1346 3" potted conduit assembly, used in Z078E, Z079E, Z080E and Z084E $113.50

1354 Wire harness for use with Wayne™ DL non-blenders $115.50

1354A 1354 wire harness with interface module $415.50

1360 Wire harness, universal $45.00

1360A 1360 wire harness with interface module, universal $345.25

1362Wire harness for use with Tokheim™ Premier™ C blender dispensers with 24 VDC solenoids $115.50


1363 Wire harness for use with Wayne™ 1 Vista™ and 2 Vista™ blender dispensers $115.50


1365 Wire harness for use with Wayne™ Ovation, 3 Vista™ and 4 Vista™ dispensers $115.50


1368Wire harness for use with Gilbarco™ Encore™ 300 blender dispensers, early AC solenoids, pre-April 2003 $115.50


1372For use with earlier version Tokheim™ blender dispensers with AC and DC solenoids

$115.50


1373Wire harness for use with Gilbarco™ Encore™ 300 and 500 Series dispensers, with 24VDC solenoids $115.50


1374 Wire harness for use with Gasboy™ 9800 $115.50


1404 Universal mounting kit $270.25

144401 VP1000 front cover assembly (98008 o-ring sold separately) $270.25

MC100-1 Universal interface module only $300.50

VP1000-5 Vacuum pump only, 110 Volt $1,823.75RVP1000-5 Rebuilt VP1000-5 vacuum pump only supplementVP1000-5 Core VP1000-5 core in reusable condition for rebuild supplementVP1000-220 International vacuum pump only, 220 Volt $1,857.25

MC200-1 International control module only, 220 Volt $336.00

131602901 International 6" potted conduit assembly, 220V $113.50

1380 International wire harness, universal 220V $42.75

1380A International 1380 wire harness with interface module, universal 220V $380.75

MC100-1 PLUG Replacement jumper plug for interface module $5.75

98008 O-ring for VP1000 front cover $4.75

144402 VP1000 front cover assembly (international only) $304.75

VP1000VRC-G Vane and rotor replacement, pps $220.75

VP1000 Replacement Parts

Ovation™ is a trademark of Dresser Inc. Tokheim™ and Premier™ are trademarks of Tokheim Holding B.V.


Vista™ is a trademark of Dresser Inc. Wayne™ is a trademark of Dresser Equipment Group Inc.

113


VP1200-11 Self-contained suction pump-mounted assembly with bronze rotor $628.25

VP1200-13 Self-contained suction pump-mounted assembly with flame arrestors and bronze rotor $744.50

VP1200-21 Self-contained suction pump-mounted assembly with PPS rotor $613.25

VP1200-23 Self-contained suction pump-mounted assembly with flame arrestors and PPS rotor $686.75

VP1200VR-B Vane and rotor kit (bronze) $245.25

127434 Machine key, square $4.25

VP1200 Series Self-Contained Suction Pump Dispenser-Mounted Vacuum Source

Note: For international markets, contact factory for additional information. Non-electric, powered by a suction dispenser pump motor.

114


400-04 FS 400 ORVR compatible nozzle, unleaded, full-service with black scuffguard* $543.00

400-04 RFS Rebuilt 400 ORVR compatible nozzle, unleaded, full-service with black scuffguard* supplement

400-04 SS 400 ORVR compatible nozzle, unleaded, self-service with black scuffguard* $543.00

400-04 RSS Rebuilt 400 ORVR compatible nozzle, unleaded, self-service with black scuffguard* supplement

400 Core 400 nozzle core, in reusable condition for rebuild supplement

468 400 nozzle scuffguard, black $18.25

468BL 400 nozzle scuffguard, blue $18.25

468G 400 nozzle scuffguard, green $18.25

468GD 400 nozzle scuffguard, gold $18.25

468R 400 nozzle scuffguard, red $18.25

468SL 400 nozzle scuffguard, silver $18.25

468W 400 nozzle scuffguard, white $18.25

469 400 nozzle handle cover $12.25

405220905 400 nozzle spout kit includes 408-2A spout assembly, 408-OR O-ring kit, 409 boot assembly $172.25

405219904 400 nozzle boot assembly includes 425 boot clamp $106.00

405221901

400 nozzle hold-open clip kit includes 6238-2 hold-open clip, 239-L rear guard rivet, 6249 spring, 6130-4 lever assembly, 240-SS pal nut, 219 front guard rivet, 6358 hand guard and 235-C lever cover

$35.25


600-02G3 FS 600 bootless nozzle, unleaded, full-service with black scuffguard* $387.75

600-02G6 FS 600 bootless nozzle, unleaded, full-service with black scuffguard* with G6 Spout $387.75

600-02G9 FS 600 bootless nozzle, unleaded, full-service with black scuffguard* with G9 Spout $387.75

600-02G3 RFS Rebuilt 600 bootless nozzle, unleaded, full-service with black scuffguard* supplement

600-02G3 SS 600 bootless nozzle, unleaded, self-service with black scuffguard* $387.75

600-02G3 RSS Rebuilt 600 bootless nozzle, unleaded, self-service with black scuffguard* supplement










6030Y 600 nozzle scuffguard, yellow $17.00

405219903 600 nozzle vapor escape guard and 6119 boot clamp, black $22.75

400 Series ORVR Nozzle

*Nozzles are supplied with black scuffguards unless otherwise specified. To order a nozzle with a scuffguard color other than black, place appropriate “X” code after “04” in the model number as follows: BL for blue, GD for gold, G for green, R for red, SL for silver or W for white.

600 Series Bootless Nozzle


115


405220903600 nozzle spout kit includes 6206-G4 spout assembly, 6206-OR O-ring kit, 6118 vapor escape guard, and 6119 boot clamp $123.25

405221901

600 nozzle hold-open clip kit includes 6238-2 hold-open clip, 239-L rear guard rivet, 6249 spring, 6130-4 lever assembly, 240-SS pal nut, 219 front guard rivet, 6358 handguard and 235-C lever cover

$33.00


800-02G3 FS 800 ORVR compatible nozzle, unleaded, full-service with black scuffguard* $439.25

800-02G3 RFS Rebuilt 800 ORVR compatible nozzle, unleaded, full-service with black scuffguard* supplement

800-02G3 SS 800 ORVR compatible nozzle, unleaded, self-service with black scuffguard* $439.25

800-02G3 RSS Rebuilt 800 ORVR compatible nozzle, unleaded, self-service with black scuffguard* supplement











405219902 800 nozzle mini-boot with face seal and 640956 boot clamp $85.50

405220902 800 nozzle spout kit includes 8177 spout assembly, 6206-OR O-ring kit, 6395A boot and $159.25

405221901 800 nozzle hold-open clip kit includes 6238-2 hold open clip, 239-L rear guard rivet, 6249 $33.00


708-02G3 FS 708 ORVR compatible nozzle, unleaded, full-service, with black scuffguard* $545.00

708-02G3 SS 708 ORVR compatible nozzle, unleaded, self-service, with black scuffguard* $545.00





6408G 708 nozzle scuffguard, green $17.00Continued on next page

*Nozzles are supplied with black scuffguards unless otherwise specified. To order a nozzle with a scuffguard color other than black, place appropriate “X” code after “G3” in model number, as follows: BL for blue, GD for gold, G for green, R for red, SL for silver, W for white or Y for yellow.


600 Series Bootless Nozzle Continued

*Nozzles are supplied with black scuffguards unless otherwise specifi ed. To order a nozzle with a scuffguard color other than black, place appropriate “X” code after “G3” in the model number as follows: BL for blue, GD for gold, G for green, R for red, SL for silver, W for white or Y for yellow.


116






405219902 708 nozzle mini-boot with 279A face seal and 640956 boot clamp $85.50

405220902708 dripless nozzle spout kit includes 8177 spout assembly, 6206-OR O-ring kit, 6395A boot assembly and 640956 boot clamp $159.25

405221901

708 nozzle hold-open clip kit includes 6238-2 hold-open clip, 239-L rear guard rivet, 6249 spring, 6130-4 lever assembly, 240-SS pal nut, 219 front guard rivet, 6358 hand guard and 235-C lever cover

$33.00


709-02G3 FS 709 ORVR compatible nozzle, unleaded, full-service, with black scuffguard* $633.75

709-02G3 SS 709 ORVR compatible nozzle, unleaded self-service, with black scuffguard* $633.75











405220901 709 dripless nozzle spout kit includes 8155 spout assembly, 6206-OR O-ring kit, 6395B boot $201.50

405221901 709 nozzle hold-open clip kit includes 6238-2 hold-open clip, 239-L rear guard rivet, 6249 $33.00


900-02G3 FS 900 EVR/ORVR compatible nozzle, unleaded, full-service with black scuffguard* $478.75

900-02G3 RFS Rebuilt 900 EVR/ORVR compatible nozzle, unleaded, full-service with black scuffguard* supplement

900-02G3 SS 900 EVR/ORVR compatible nozzle, unleaded, self-service with black scuffguard* $478.75

900-02G3 RSS Rebuilt 900 EVR/ORVR compatible nozzle, unleaded, self-service with black scuffguard* supplement


708 Series ORVR Nozzle Continued


900 Series EVR Certified Nozzle

*Nozzles are supplied with black scuffguards unless otherwise specifi ed. To order a nozzle with a scuffguard color other than black, place appropriate “X” code after “G3” in model number, as follows: BL for blue, GD for gold, G for green, R for red, SL for silver, W for white or Y for yellow.



117












405220901 900 dripless nozzle spout kit includes 8155 spout assembly, 6206-OR O-ring kit, 6395B boot $201.50

405221901 900 nozzle hold-open clip kit includes 6238-2 hold-open clip, 239-L rear guard rivet, 6249 $33.00

900 Series EVR Certified Nozzle Continued


118

Model Description List75B-030-S2S2 3' standard Healy coaxial hose $114.75

75B-035-S2S2 3½' standard Healy coaxial hose $118.75

75B-040-S2S2 4' standard Healy coaxial hose $122.25





















75B-010-S3F3 1' metric-ready dispenser coxial hose $92.25






75B-075-S3F3 7½' metric-ready dispenser coxial hose $154.75



75B-090-S3F3 9 metric-ready dispenser coxial hose $164.75




75 Series ¾" Standard Healy Hose


119

Model Description List75B-110-S3F3 11' metric-ready dispenser coxial hose $179.50





Model Description List75B-008-F2F2 Healy straight thread, fixed ends on breakaway and dispenser ends $78.25

75B-008-F3F2 Healy straight thread, fixed end on breakaway end, metric thread on dispenser end $78.25

75B-008-S2F2 Healy straight thread, fixed end on breakaway end, swivel end on dispenser end $86.25

75B-008-S3F2 Healy straight thread, fixed end on breakaway end, metric swivel thread end on dispenser end $86.25

75B-010-S4F2 Fixed end on breakaway end, balance swivel end on dispenser end $106.00

Model Description List75B-080-S3F2 8' metric-ready dispenser coaxial hose $157.50

75B-085-S3F2 8½' metric-ready dispenser coaxial hose $161.00

75B-090-S3F2 9' metric-ready dispenser coaxial hose $164.75











Note: Healy hoses are available from three feet up to 20 feet; contact factory for pricing and availability of lengths not shown. Hoses are CARB-approved for overall assembly lengths up to 20 feet, including breakaway and whip hose.

*Hoses are supplied in black unless otherwise specified. To order a hose in a color other than black, replace “B” with the code as follows: BL = blue, G = green, R = red. Consult factory for pricing.

75 Series ¾" Standard Whip Hose

Note: Hose ends are defined as follows: F2 = fixed ends with Healy straight thread, F3 = fixed ends with metric M-34 thread, S2 = swivel ends with Healy straight thread, S3 = swivel ends with metric M-34 thread, S4 = swivel ends with balance-type thread.


75 Series ¾" Healy Hose for Metric-Ready Dispensers


75 Series ¾" Standard Healy Hose Continued

120

Model Description List75B-080-S4F2 8' balance-ready dispenser coaxial hose $169.75

75B-085-S4F2 8½' balance-ready dispenser coaxial hose $173.25

75B-090-S4F2 9' balance-ready dispenser coaxial hose $177.25











75 Series ¾" Healy Hose for Balance-Ready Dispensers

Note: Healy hoses are available from three feet up to 20 feet; contact factory for pricing and availability of lengths not shown. Hoses are CARB-approved for overall assembly lengths up to 20 feet, including breakaway and whip hose.


121

Model Description List75B-080-S2S7 8' standard Healy coaxial hose $250.75













Model Description ListCX6-A Hose adapter, non-vapor ready, NPT $49.25

CX6-AE Hose adapter, non-vapor ready, BSP, international only $54.75

CX6-VV3A Hose adapter, non-vapor ready, multi-product units $95.00

Model Description List715VV Repair kit for 8701VV breakaway, includes valves and O-rings $54.75

761 Nozzle end for 8701VV breakaway scuffguard $7.75

762 Dispenser end for 8701VV breakaway scuffguard $7.75

787 Nickel plated brass shear screw for 8701VV $7.75

787-1 Nickel plated brass shear screw for 807 swivel breakaway $7.75

795 Clamp repair tool for 8701VV and 807 breakaway $175.00

807 Swivel breakaway installed between hose and nozzle $230.50

8701VV Standard hose breakaway with vapor path shut-off, 350 lbs. strength $134.75

Z055 O-ring kit for 8701VV with nickel plated shear screw $17.25

Model Description ListZ008 Standard for single-hose dispenser $104.75

Z009 Standard for dual-hose dispenser $170.75

Z044C Universal for six-hose multi-product dispenser $325.50

Z046C Universal for four-hose multi-product dispenser $272.00

Z047C Universal for two-hose multi-product dispenser $197.50

75 Series ¾" 700 Series Healy Hose

Note: Healy hoses are available from three feet up to 20 feet; contact factory for pricing and availability of lengths not shown.


75 Series Coaxial Hose Adapters

75 Series Standard and Balance-Ready Healy Hose Breakaways

Dispenser Vapor Retrofit Kits (Hose adapters are not included in retrofit kits)

122

Model Description List516 Hose end O-ring for S4 fitting, large $4.00

1301 Hose flow limiter for 8701VV standard breakaway, installed between breakaway and main hose $63.00

1302 Hose flow limiter for 807 swivel breakaway, installed between main hose and nozzle $63.00

8103 Hose clamp, for connect to hose retractor $23.75

HB-2 Hose end O-ring for S2 fitting, large $4.00

HB-4 Vapor end quad ring (2 required per adaptor) $4.00

291 Vapor end O-ring (2 required per adaptor) $4.00

6094 Hose end O-ring for S3 fitting, large $4.00

405322918 S4F2 field replacement label kits (8 labels and 1 instruciton per kit) $20.50

405322911 S2S2 field replacement label kit (8 labels and 1 instruction per kit) $20.50

Hose Accessories and Spare Parts

123

¾" Low Permeation Vapor Recovery HoseModel Description List 75B-008-F2F2-LP ¾" x 8" whip hose, F2 x F2 fittings $64.75 75B-008-F3F2-LP ¾" x 8" whip hose, F3 x F2 fittings $67.25 75B-008-S2F2-LP ¾" x 8" whip hose, S2 x F2 fittings $79.75 75B-008-S3F2-LP ¾" x 8" whip hose, S3 x F2 fittings $80.25 75B-010-S4F2-LP ¾" x 1' hose, S4 x F2 fittings $103.5075B-040-S4F2-LP ¾" x 4' hose, S4 x F2 fittings $148.7575B-045-S4F2-LP ¾" x 4'6" hose, S4 x F2 fittings $157.7575B-050-S4F2-LP ¾" x 5' hose, S4 x F2 fittings $166.00

75B-050-S2F2-LP ¾" x 5' hose, S2 x F2 fittings $148.7575B-050-S2S2-LP ¾" x 5' hose, S2 x S2 fittings $164.7575B-055-S4F2-LP ¾" x 5'6" hose, S4 x F2 fittings $173.2575B-060-S2S2-LP ¾" x 6' hose, S2 x S2 fittings $180.00

75B-070-S2S2-LP ¾" x 7" hose, S2 x S2 fittings $194.75

75B-080-S2S2-LP ¾" x 8' hose, S2 x S2 fittings $210.50

75B-085-S2S2-LP ¾" x 8'6" hose, S2 x S2 fittings $220.00


75B-090-S4F2-LP ¾" x 9' hose, S4 x F2 fittings $229.00





75B-145-S4F2-LP ¾" x 14'6" hose, S4 x F2 fittings $316.75




Low Perm hoses are supplied in black only with a light green stripeNote: Hose ends are defined as follows: F2 = fixed ends with Healy straight thread, F3 = fixed ends with metric

M-34 thread, S2 = swivel ends with Healy straight thread, S3 = swivel ends with metric M-34 thread, S4 = swivel ends with balance-type thread.

124

Model Description List75B-010-S3F3 1' metric-ready dispenser coaxial hose, $92.2575B-020-S3F3 2' metric-ready dispenser coaxial hose $116.00

















HEALY FLEXSTEEL FUTURA Vapor Assist Hose for Metric Swivel X Metric Fixed

Note: Healy hoses can be made to custom lengths; contact factory for pricing and availability of lengths not shown. Hoses are CARB-approved, including breakaway and whip hose. *Hoses are supplied in black unless otherwise specified. To order a hose in a color other than black, replace “B” with the code as follows: BL = blue, G = green, R = red. Consult factory for pricing.

125


9000-02 9000 mini-jet, non-electric with syphon port, can handle eight fueling positions with four nozzles in simultaneous full flow

$1,892.00

650-104-02 9000 mini-jet check valve strainer assembly (replaces 912A) $42.75

940A Vacuum regulator upgrade kit $223.00

965 O-ring (1 per cover) $4.75

CV4 O-ring, for strainer assembly $4.75


VP500B VP500 vane pump with U-bolts and angle bracket for mounting, handles 10 fueling positions with fi ve nozzles in simultaneous full flow

$1,879.75

VP500 Replacement VP500 vane pump with regulator and flame arrestor assembly $1,761.00

VP500VR-3 VP500 vane and rotor replacement kit, pin drive $822.00

5007A Regulator assembly $101.00

9214 VP500 flame arrestor $70.75

Model Description List100 100 jet pump central vacuum source, two required for each hose $543.00

930 100 jet pump central vacuum source O-ring $9.25

1005W-4 STP sensing relay for product input $151.25

1258A 100 jet pump external relief valve assembly $85.75

100 Jet Pump Central Vacuum Source

9000 Series Mini-Jet Central Vacuum Pump

Note: Central vacuum source installations may require the use of the Healy 6280 monitor assembly.

VP500 Central Vacuum Vane Pump

126

Model Description List8175 Surrogate spout assembly, for use with 700/800/900 Series nozzles $113.50

9968 Clean air separator test port assembly $345.25

2302A Gauge kit, 1-0-1" water column $194.00

6059 Spout adapter, air/liquid ratio test, for use with 600 Series nozzle only $154.75

8034-1 Spout adapter, air/liquid ratio test, for use with 700/800/900 Series nozzles only $157.00

8175-1 Surrogate spout assembly including 8034-1, for use with 700/800/900 Series nozzles only $270.25

939349A Gauge kit, 0-100" water column $194.00

Z076Roots meter package, 600 Series nozzle, includes Dresser Roots vapor recovery meter, fl ange kit, 1½" NPT × ½" NPT reducer, 6' × ¾" hose, 600 Series nozzle spout adapter and two ½" NPT × ¾" hose barb fittings

$5,701.00

Z077Roots meter package, 700/800/900 ORVR nozzle, includes Dresser Roots vapor recovery meter, flange kit, 1½" NPT × ½" NPT reducer, 6' × ¾" hose, ORVR nozzle spout adapter and two ½" NPT × ¾" hose barb fittings

$5,701.00

63034 O-ring, for 8034-1 spout adapter $4.75

8006 Magnet strip assembly (for use with spout adapter 8034-1) $50.50

System Test Equipment

127

¾" BreakawaysModel Description List69713701 ¾" EBW Safety-Sever Reconnectable Breakaway NPT Inlet $41.5069813321 ¾" EBW Safety-Sever Breakaway BSPT Inlet $47.2569713301 ¾" EBW Safety-Sever Replacement Set Screw $8.00

¾" NozzlesModel Description List402315901 ¾" EBW Farm/utility nozzle w leaded (diesel) spout; BUNA gaskets $18.50402315903 ¾" EBW Farm/utility nozzle w unleaded spout; BUNA gaskets $18.5040231441 ¾" EBW Farm/utility nozzle w unleaded spout; Fluorocarbon gaskets $30.75498303901 ¾" EBW 498 Manual Nozzle w leaded (diesel) spout; BUNA gaskets $98.25

Model Description List402315902 1" EBW Farm/Utility Nozzle w leaded (diesel) spout; BUNA gaskets $18.50 402315904 1" EBW Farm/Utility Nozzle w unleaded spout; BUNA gaskets $18.5040231342 1" EBW Farm/utility nozzle w leaded (diesel) spout; Fluorocarbon gaskets $20.5040231442 1" EBW Farm/utility nozzle w unleaded spout; Fluorocarbon gaskets $20.5049830102 1" EBW 498 Manual Nozzle w leaded (diesel) spout; BUNA gaskets $106.7549830106 1" EBW 498 Manual Nozzle w leaded spout; BUNA gaskets, no check $105.5049030105 1" EBW 490 Dual Poppet Nozzle w 1.25" outlet $155.5049540201 1" EBW 495 Aircraft Fueling Nozzle $256.00

1" BreakawaysModel Description List79722501 1" EBW Safety-Sever Reconnectable Breakaway NPT Inlet $91.7579713301 1" EBW Safety-Sever Replacement Set Screw $9.75

Model Description List46510101 1¼" EBW 1¼" X 1¼" Hose Swivel without check $87.2546510102 1¼" EBW 1¼" X 1¼" Hose Swivel with check $101.00

Model Description List41030003 1¼" EBW 1¼" 410 Fuel Oil Delivery Nozzle $167.7549030106 1¼" EBW 1¼" 490 Dual Poppet Nozzle w 1¼" outlet $167.7549030201 1¼" EBW 1¼" 490 Dual Poppet Nozzle w 1½" outlet $160.0049540101 1¼" EBW 495 Aircraft Fueling Nozzle $335.00

Nozzles, Swivels, Breakaways, & Accessories

1" Utility / Farm Nozzles Products

1¼" Swivels

1¼" Nozzles

128

Model Description List46510201 1½" EBW 1½" X 1½" Hose Swivel without check $90.7546510202 1½" EBW 1½" X 1½"Hose Swivel with check $107.75

Model Description List41511001 1½" Automatic High Flow Bulk Fuel Nozzle $437.2541040103 1½" EBW 1½" 410 Fuel Oil Delivery Nozzle $176.5049540001 1½" EBW 495 Aircraft Fueling Nozzle $350.50


HRTRVRHose retriever kit including head with 2" NPT inlet, cable, counterweight, pulley and hose clamps (additional counterweights available - contact Customer Service) $215.75

HRTRVRBASE Hose retriever base plate, 2" NPT inlet $106.50 8103 ¾" single hose clamp $23.75HB100 1" hose diameter hose support $160.00HB125 1¼" hose diameter hose support $181.25HB150 1½" hose diameter hose support $189.00

HRTRTR Hose Retractor, 20lbs counterwieght, 30 lbs $213.25

Model Description ListVAX075FNPT Vapor recovery conversion adapter, vac-assist to¾" standard conventional $42.25

BAX075FNPT Balance vapor recovery conversion adapter, balance to ¾" standard conventional $42.25

HEX075FNPT HEALY vac-assist conversion adapter, HEALY vacassist to ¾" standard conventional $42.25

Model Description List495-210-01 Spout for 495-400-01 $49.75

495-105-01 Dust cap assembly for 495-400-01 $20.00

495-107-01 Ground wire assembly for 495-400-01 $20.75

495-211-01 Spout for 495-401-01 $46.75

495-125-01 Strainer for 495-401-01 $60.50



495-112-01 Spout for 495-402-01 $60.50

495-204-01 Strainer for 495-402-01 $34.50


RE-STAGE Stage II Replacement Adapters

1½" Nozzles

495 Utility Nozzle Replacement Parts

1½" Swivels

Hose Retriever Systems

129

Model Description List495-111-01 Dust cap assembly for 495-402-01 $18.00


495-210-01 Spout for 495-401-01 $49.75


495-120-01 1-1/2" tube and strainer assembly, aluminum $90.25

495-120-02 1-1/2" tube and strainer assembly, brass $88.00

495-122-01 1-1/4" tube and strainer assembly, aluminum $109.75

Model Description List410-116-01 1-3/8" for 1.5" 410 and 490 series nozzles $50.50

410-122-01 1-1/8" for 1.25" 410 and 490 series nozzles $50.50



Model Description List491-100-01 1.25" nozzle tube for 410 and 490 series nozzles $18.00

491-101-01 1.50 nozzle tube for 410 and 490 series nozzles $20.00

491-107-01 1.00" nozzle tube and nut for 410 and 490 series nozzles $31.00

ListModel Description List495-105-01 For use with 1.5" nozzle $20.00

495-106-01 For use with 1.25" nozzle $18.00

495-111-01 For use with 1" nozzle $18.00

Model Description List495-107-01 78" ground wire $20.75

Model Description List495-125-01 1.25", steel strainer $60.50

495-204-01 1", brass strainer $34.50

495-209-01 1.5" brass strainer $37.50

495 Utility Nozzle Replacement Parts Continued

Ground Wire Assembly

Strainers

Nozzle AccessoriesBrass Nozzle Tubes & Nut Assemblies

Aluminum Nozzle Tubes

Dust Cap Assembly

130

DuraDEF™ Diesel Exhaust Fluid NozzleModel Description ListDURADEF-LB Light blue DuraDEF nozzle with hold-open clip $243.50DURADEF-LB-O Light blue DuraDEF nozzle no hold-open clip $243.50

DuraDEF™ Diesel Exhaust Fluid Nozzle With Mis-Fill Prevention SpoutModel Description ListDURADEF-MPD DuraDEF nozzle with mis-fill prevention spout, hold-open clip, light blue scuff guard $280.75DURADEF-MPD-O DuraDEF nozzle with mis-fill prevention spout no hold-open clip, light blue scuff guard $280.75DEF-MPD Mis-fill prevention device for ¾" spout $40.50

BRK34SS-N ¾" NPT DEF break away $166.50BRK34SS-P ¾” BSPP DEF break away $166.50

Diesel Exhaust Fluid Swivel Break Aways

OMNIDEF1X34N ¾" NPT nozzle outlet, 1" BSPP female inlet DEF swivel break away $95.75

OMNIDEF1X34P ¾” BSPP nozzle outlet, 1” BSPP female inlet DEF swivel break away $95.75OMNIDEF1PXM34 M34 (metric) nozzle outlet, 1" BSPP female inlet DEF swivel break away $95.75

DEF Hanging Hardware

Diesel Exhaust Fluid Break Aways

131

Length 5/8" P/N 5/8" List Price 3/4" P/N 3/4" List Price 1" P/N 1" List Price9" WHIP FLHFR100009 $12.75 FLHFR200009 $14.50 FLHFR300009 $21.5012" WHIP FLHFR100100 $16.75 FLHFR200100 $15.50 FLHFR300100 $22.758' FLHFR100800 $34.50 FLHFR200800 $39.00 FLHFR300800 $51.758.5' FLHFR100806 $35.75 FLHFR200806 $40.50 FLHFR300806 $54.009' FLHFR100900 $37.25 FLHFR200900 $42.25 FLHFR300900 $56.009.5' FLHFR100906 $39.00 FLHFR200906 $44.00 FLHFR300906 $57.7510' FLHFR101000 $40.50 FLHFR201000 $45.75 FLHFR301000 $60.5010.5' FLHFR101006 $42.00 FLHFR201006 $47.50 FLHFR301006 $62.5011' FLHFR101100 $43.25 FLHFR201100 $49.00 FLHFR301100 $64.7512' FLHFR101200 $46.25 FLHFR201200 $52.50 FLHFR301200 $69.2513' FLHFR101300 $49.50 FLHFR201300 $55.50 FLHFR301300 $73.5014' FLHFR101400 $52.00 FLHFR201400 $59.25 FLHFR301400 $78.0015' FLHFR101500 $55.50 FLHFR201500 $62.50 FLHFR301500 $82.2516' FLHFR101600 $58.25 FLHFR201600 $66.00 FLHFR301600 $86.5017' FLHFR101700 $61.50 FLHFR201700 $69.25 FLHFR301700 $91.0018' FLHFR101800 $64.25 FLHFR201800 $72.75 FLHFR301800 $95.2519' FLHFR101900 $67.50 FLHFR201900 $76.00 FLHFR301900 $99.5020' FLHFR102000 $70.25 FLHFR202000 $79.50 FLHFR302000 $104.0025' FLHFR102500 $85.25 FLHFR202500 $96.25 FLHFR302500 $125.7550' FLHFR105000 $160.00 FLHFR205000 $180.50 FLHFR305000 $234.2575' FLHFR107500 $235.75 FLHFR207500 $164.50 FLHFR307500 $342.00100' FLHFR110000 $308.25 FLHFR210000 $348.50 FLHFR310000 $451.25

Approvals / Certifications: UL and cUL listed.

Notes:

FLEX-ON™ Black Hardwall Hose- Fixed Ends

Available in colors other than BLACK. YL = Yellow, RD = Red, GR = Green, BL = BlueFor color hose pricing - add 20% to List Price.

Available with swivel fitting options for enhanced ease of use. Add $5.50 per swivel

For 5/8" and 3/4" - add $5.50 per swivel and for 1" - add $10.00 per swivel

*See hose speficications on the Dispensing Systems web page at www.franklinfueling.com

Ordering Guide - Example: FLHFR200806YLSWOE = FLEX-ON™ Hardwall Hose, ¾" diameter, 8 feet 6 inches length, yellow color, swivel on one end.

132

FLEX-ON™ Black Softwall Hose

Length 3/4" P/N 3/4" List Price 1" P/N 1" List Price9" WHIP FLXSW200009 $14.50 FLXSW300009 $19.50

8' FLXSW200800 $30.50 FLXSW300800 $49.75

8.5' FLXSW200806 $31.75 FLXSW300806 $51.75

9' FLXSW200900 $32.75 FLXSW300900 $53.75

9.5' FLXSW200906 $34.00 FLXSW300906 $55.50

10' FLXSW201000 $35.00 FLXSW301000 $57.50

10.5' FLXSW201006 $36.25 FLXSW301006 $59.50

11' FLXSW201100 $37.50 FLXSW301100 $61.50

12' FLXSW201200 $39.75 FLXSW301200 $65.25

13' FLXSW201300 $42.00 FLXSW301300 $69.25

14' FLXSW201400 $44.25 FLXSW301400 $73.00

15' FLXSW201500 $46.75 FLXSW301500 $77.00

16' FLXSW201600 $49.00 FLXSW301600 $80.75

17' FLXSW201700 $51.25 FLXSW301700 $84.25

18' FLXSW201800 $53.50 FLXSW301800 $88.00

19' FLXSW201900 $55.75 FLXSW301900 $92.00

20' FLXSW202000 $58.25 FLXSW302000 $95.75

25' FLXSW202500 $69.75 FLXSW302500 $119.50

50' FLXSW205000 $127.75 FLXSW305000 $219.00

75' FLXSW207500 $185.75 FLXSW307500 $317.00

100' FLXSW210000 $243.50 FLXSW310000 $412.75

Approvals / Certifications: UL and cUL listed.Notes:


Available only in BLACK color onlyAvailable with swivel fitting options for enhanced ease of use. For 3/4" - add $5.50 per swivel and for 1" - add $10.00 per swivel

Ordering Guide - Example: FLXSW201006SWOE = FLEX-ON™ Softwall Hose, ¾” diameter, 10 feet, 6 inches, swivel on one end.

133

FLEX-ON™ Marina HoseLength 3/4" P/N 3/4" List Price 1" P/N 1" List Price

3' FLXBM200300 $28.50 FLXBM300300 $40.00

10' FLXBM201000 $77.00 FLXBM301000 $94.00

16' FLXBM201600 $117.00 FLXBM301600 $145.25

20' FLXBM202000 $142.25 FLXBM302000 $180.25

25' FLXBM202500 $161.75 FLXBM302500 $234.75

35' FLXBM203500 $218.00 FLXBM303500 $311.50

40' FLXBM204000 $246.25 FLXBM304000 $351.00

50' FLXBM205000 $303.25 FLXBM305000 $429.00

60' FLXBM206000 $359.00 FLXBM306000 $465.75

75' FLXBM207500 $443.75 FLXBM307500 $623.50

100' FLXBM210000 $584.75 FLXBM310000 $817.25

125' FLXBM212500 $725.75 FLXBM312500 $1,012.50

150' FLXBM215000 $866.75 FLXBM315000 $1,243.25

200' FLXBM220000 $1,149.25 FLXBM320000 $1,595.50

Approvals / Certifications: UL and cUL listed.Notes:

*See hose speficications on the Dispensing Systems web page at www.franklinfueling.comOrdering Guide:

Comes in GREEN color (Also available in BLUE…add "BL" to the end of part #)Available with swivel fitting options for enhanced ease of use. For 3/4" - add $5.50 per swivel and for 1" - add $10.00 per swivel

Example #1 : FLXBM201006SWOE = FLEX-ON™ Marina Hose, ¾” diameter, 10 feet, 6 inches, swivel on one end. Example #2 : FLXBM201006BLSWOE = FLEX-ON™ Marina Hose, BLUE, ¾” diameter, 10 feet, 6 inches, swivel on one end.

134

FLEX-COLD Cold Weather HoseLength 3/4" P/N 3/4" List Price 1" P/N 1" List Price

9" WHIP FLXCW200009 $20.50 FLXCW300009 $28.50

8' FLXCW200800 $98.75 FLXCW300800 $143.25

9' FLXCW200900 $108.50 FLXCW300900 $160.00

9.5' FLXCW200906 $112.75 FLXCW300906 $168.50

10' FLXCW201000 $120.00 FLXCW301000 $177.00

12' FLXCW201200 $142.00 FLXCW301200 $209.00

15' FLXCW201500 $173.75 FLXCW301500 $251.75

16' FLXCW201600 $185.00 FLXCW301600 $270.50

18' FLXCW201800 $205.75 FLXCW301800 $301.00

25' FLXCW202500 $283.25 FLXCW302500 $421.50

30' FLXCW203000 $341.00 FLXCW303000 $501.75

Approvals / Certifications: UL and cUL listed.

Notes:

*See hose speficications on the Dispensing Systems web page at www.franklinfueling.comOrdering Guide: Example #1: FLXCW200906 = FLEX-COLD cold weather hose, ¾" diameter, 9 feet 6 inches length. Example #2: FLXCW303000 = FLEX-COLD cold weather hose, 1" diameter, 30 feet length.

Not available with swivel fitting options (recommend a stand-alone swivel) 3/4" p/n SWVL34-N or 1" p/n SWVL10-N

Designed for dispensing gasoline in extremely cold environments down to -65 ̊ F (-54 ˚C). Comes in black color with blue lay line.

135

AGRI-FLEX" Farm Hose with Static WireLength 3/4" P/N 3/4" List Price 1" P/N 1" List Price

8' FTSW200800 $19.00 FTSW300800 $30.00

10' FTSW201000 $21.75 FTSW301000 $35.75

12' FTSW201200 $24.50 FTSW301200 $38.50

14' FTSW201400 $27.50 FTSW301400 $45.00

16' FTSW201600 $31.00 FLXCW301600 $50.75

18' FTSW201800 $34.00 FLXCW301800 $59.50

20' FTSW202000 $36.75 FLXCW302000 $62.00

25' FTSW202500 $44.00 FLXCW302500 $80.25

50' FTSW205000 $83.00 FLXCW305000 $147.50

Approvals / Certifications: Not UL ListedNotes: Comes in Black Chemivic™ synthetic rubber (ORS) and reinforced with spiral synthetic yarn

Available with swivel fitting options for enhanced ease of use. Couplings: Zinc w/Zinc plated fittings and aluminum ferrules

*See hose speficications on the Dispensing Systems web page at www.franklinfueling.comOrdering Guide: Example: FTSW201000 = AGRI-FLEX™ Farm Hose, ¾" diameter, 10 feet in length

136

FLEX-ING™ Ethanol HoseLength 3/4" P/N 3/4" List Price

9" WHIP FLXE200009 $67.50

1' FLXE200100 $84.50

8' FLXE200800 $168.25

8.5' FLXE200806 $180.00

9' FLXE200900 $192.25

9.5' FLXE200906 $205.00

10' FLXE201000 $209.00

11' FLXE201100 $214.00

12' FLXE201200 $219.00

14' FLXE201400 $246.50

16' FLXE201600 $186.90

18' FLXE201800 $207.55

20' FLXE202000 $226.98

50' FLXE205000 $514.50

Approvals / Certifications: UL listed for use in ethanol dispensing applications up to E85Notes:


Ordering Guide - Example: FLHFR200806YLSWOE = FLEX-ON™ Hardwall Hose, ¾" diameter, 8 feet 6 inches length, yellow color, swivel on one end.

137

FLEX-ING Diesel Exhaust Fluid (DEF) HosesLength 3/4" P/N 3/4" List Price

9" WHIP FLDEF200009-XX-XX $47.50

1' FLDEF200100-XX-XX $49.00 XX-XX Combinations include:8' FLDEF200800-XX-XX $91.00 2N-2N8.5' FLDEF200806-XX-XX $93.50 2N-2P9' FLDEF200900-XX-XX $97.00 2P-2P9.5' FLDEF200906-XX-XX $100.50 3P-3P10' FLDEF201000-XX-XX $104.00 3P-3PF10.5' FLDEF201006-XX-XX $107.50 3PF-3PF11' FLDEF201100-XX-XX $113.00 2P-3P12' FLDEF201200-XX-XX $119.25 2N-3P13' FLDEF201300-XX-XX $125.00

14' FLDEF201400-XX-XX $131.50

15' FLDEF201500-XX-XX $138.00 3 = 1'16' FLDEF201600-XX-XX $144.25 N = NPT17' FLDEF201700-XX-XX $150.25 P = BSPP17.5' FLDEF201700-XX-XX $155.75 F = FEMALE SWIVEL NUT18' FLDEF201800-XX-XX $161.50

19' FLDEF201900-XX-XX $167.00

20' FLDEF202000-XX-XX $170.25

25' FLDEF202500-XX-XX $173.50

30' FLDEF203000-XX-XX $186.75

35' FLDEF203500-XX-XX $217.00

50' FLDEF205000-XX-XX $285.00

75' FLDEF207500-XX-XX $462.00

Notes:


Available with 1" female BSPP swivel (captured nut) option for enhanced ease of installation.

Approvals: Meets ISO 22241 standard ensuring desirable characteristics of AUS 32 (DEF) are met, such as quality, safety, reliability and contamination.

2 = 3/4"

Includes blue anti-kinking sleeves on both ends of hose.

138

FLEX-ING™ Low Permeation HoseLength 3/4" P/N 3/4" List Price

9" WHIP FLHLP200009 $44.648' FLHLP200800 $90.759' FLHLP200900 $102.259.5' FLHLP200906 $110.5010' FLHLP201000 $117.0011' FLHLP201100 $130.2512' FLHLP201200 $143.50Approvals / Certifications: CARB Approved and meets UL330 permeation limit of 10g/m^2/day

Notes: Available with swivel fitting options for enhanced ease of use.

*See hose speficications on the Dispensing Systems web page at www.franklinfueling.comOrdering Guide: Example #1 : FLHLP200906SWOE= Continental ContiTech ¾” diameter, 9 feet, 6 inches, swivel on one end.

On the 3/4" - add $5.50 per swivel

139

FLEX-ING™ Service Station Air Hose

Color Length 1/4" Softwall P/N1/4" Softwall

List Price 1/4" Hardwall P/N1/4" Hardwall List

PriceBLACK 25' FLXAH25X025BK $22.75 FLBAH25X025 $66.00

BLUE 25' FLXAH25X025BL $22.75

RED 25' FLXAH25X025RD $22.75 FLRAH25X025 $68.00

BLACK 50' FLXAH25X050BK $38.00 FLBAH25X050 $124.00

BLUE 50' FLXAH25X050BL $38.00

RED 50' FLXAH25X050RD $38.00 FLRAH25X050 $128.00

BLACK 25' FLXAH25X025-FSWOEBK $22.75 FLBAH25X025-FSWOE $66.00

BLUE 25' FLXAH25X025-FSWOEBL $22.75

RED 25' FLXAH25X025-FSWOERD $22.75 FLRAH25X025-FSWOE $68.00

BLACK 50' FLXAH25X050-FSWOEBK $38.00 FLBAH25X050-FSWOE $124.00

BLUE 50' FLXAH25X050-FSWOEBL $38.00

RED 50' FLXAH25X050-FSWOERD $38.00 FLRAH25X050-FSWOE $128.00

Available in colors other than BLACK. YL = Yellow, RD = Red, GR = Green, BL = BlueFSWOE = Female Swivel One End

Softwall Air Hose: Tube: Versigard® synthetic rubber, RMA Class C (Limited Oil Resistance)Cover: Black, Red, or Blue Versigard® synthetic rubber (*)Reinforcement: Spiral synthetic yarnFittings: Brass NPTWorking pressure: 200 PSITemperature: -40°F to 160°F (-40°C to 71°C)

Hardwall Air Hose:Tube: Nitrile synthetic rubber, RMA Class B (medium/high oil resistance)

Reinforcement: Braided (1) steel wire braidFittings: Brass NPTWorking pressure: 250 PSITemperature: -20°F to 160°F (-40°C to 71°C)

N/A

N/A

Cover: Red or black nitrile synthetic rubber, abrasion- and oil-resistant, RMA Class B (medium/high oil resistance)

1/4" Softwall P/N with Female swivel 1/4" Hardwall P/N with Female swivel

N/A

N/A

140

TS-550 evo & TS-5000 evo TS-5TXED PMY/TRLSC T5 DMX/TRTX = Model T5 = Model

550 = TS-550 evo T5 = TS-5, 110 or 220 VAC

5000 = TS-5000 evo DMX = Hardware Options

PMY = Hardware options D = Display, standard in the TS-5

P = Printer M = Internal modem

M = Internal modem X = I for dispenser interface module or E for LON™ module

Y = I for dispenser interface module or E for LON™ module TR = Software Options

TRLSC = Software Options T = SCALD 24-hour tank testing

T = SCALD 24-hour tank testing R = Reconciliation

R = Reconciliation

L = Line leak detectionS = Secondary containment monitoring

C= Conditions/DEF Recirculation

TS-550/5000TX DPMY/TRLVSTX = Model

T550 = TS-550, 110 or 220 VAC

T5000 = TS-5000, 110 or 220 VACDPMY = Hardware Options

D = Display

P = PrinterM = Internal modemY = I for dispenser interface module or E for LON™ module

TRLVS = Software Options

T = SCALD 24-hour tank testing

R = Reconciliation

L = Line leak detectionV = Vapor recovery monitoring, V for assist or B for balance

S = Secondary containment monitoring

Lon™ is a trademark of Echelon Corporation.

T5 Series Ordering GuideConsole model, software and hardware options can be listed separately or combined when ordering. Systems shipped from the factory will list the combined part number. Complete console part numbers have a specific order and are created using the following guidelines:

141

Model Description ListT550ED TS-550 evo base console without printer $5,035.00

T550EDP TS-550 evo base console with printer $5,737.00

Model Description ListT5000ED TS-5000 evo base console without printer $5,347.00

T5000EDP TS-5000 evo base console with printer $6,051.00


EVO-EXPC Secondary console to add eleven additional plug-in modules to the primary TS-550/5000 evo console, comes without a display or printer $3,400.00

EVO-EXPC2 Secondary console to add six additional plug-in modules to the primary TS-550/5000 evo console, comes without a display or printer $2,925.00


EVO-DIMIB (I) Internal dispenser interface module, dispenser interface cable must be ordered separately $1,152.00

EVO-LON (E) EcheLON™ communication module, IFSF protocol capability $798.00

TS-MDMIB (M) Internal modem, includes fax and data software capability $798.00

Note: Only one EVO-DIMIB or EVO-LON module can be installed per console.


TS-TT (T) Statistical Continuous Automatic Leak Detection, 24 hour continuous tank testing software $1,152.00

TS-TRAC (R) Tank inventory reconciliation and autocalibration $843.00

TS-ELLD (L) Electronic line leak detection $1,107.00

TS-SCM (S) Secondary containment monitoring $1,152.00

TS-CON (C) Conditions / DEF Recirulation $1,048.00

TS-5 Fuel Management SystemModel Description ListT5 TS-5 console without display $1,885.00

T5D TS-5 console with LCD display $2,256.00

Note: Includes one TS-PRB-12 input probe module


TS-DIMIB5 (I) Internal dispenser interface module, dispenser interface cable must be ordered separately $1,174.00

TS-LON5 (E) EcheLON™ communication module, IFSF protocol capability $768.00


Note: Only one TS-DIMIB or TS-LON module can be installed per console.

TS-550 evo Fuel Management System

Expansion Console

Internal Hardware Options

TS-550evo & TS-5000evo Internal Software Options



TS-5000 evo Fuel Management System

142

Internal Software OptionsModel Description List

TS-TT (T) Statistical Continuous Automatic Leak Detection, 24 hour continuous tank testingsoftware $1,152.00


TS-550Model Description ListT550 TS-550 console $2,738.00

T550D TS-550 base console with display and without printer $3,678.00

T550DP TS-550 base console with display and printer $4,380.00

Model Description ListT5000 TS-5000 base console without display and printer $3,112.00

T5000D TS-5000 base console with display and without printer $4,070.00

T5000DP TS-5000 base console with display and printer $4,789.00


TS-EXPC Secondary console to add eleven additional plug-in modules to the primary TS-550/5000 console, comes without a display or printer $3,433.00

TS-EXPC2 Secondary console to add six additional plug-in modules to the primary TS-550/5000 console, comes without a display or printer $2,954.00


TS-DIMIB (I) Internal dispenser interface module, dispenser interface cable must be orderedseparately $1,174.00

TS-LON (E) EcheLON™ communication module, IFSF protocol capability $798.00


Note: Only one TS-DIM or TS-LON module can be installed per console.


TS-TT (T) Statistical Continuous Automatic Leak Detection, 24 hour continuous tank testingsoftware $1,152.00


TS-ELLD (L) Electronic line leak detection $1,107.00

VRMEO202 (V) Vapor recovery monitoring, ISD, CARB Executive Order 202 $4,720.00

VRMEO204 (V) Vapor recovery monitoring, ISD, CARB Executive Order 204 $4,720.00

TS-SCM (S) Secondary containment monitoring $1,152.00

Internal Software Options

TS-550 and TS-5000 Fuel Management Systems

TS-5000

Expansion Console



143

Fuel Management Systems Console AccessoriesT5 Series Fuel Management System Console Interface ModulesIntrinsically Safe ModulesModel Description ListTS-PRB 12 input probe module, LL2 Series mag probes, VFM flow meters and DMS Mag sensors $847.00

TS-2WSNS 12 input 2-wire sensor module, TSP-ULS, TSP-UHS and TSP-HLS sensors $886.00

TS-3WSNS 8 input 3-wire sensor module, TSP-EIS, TSP-DIS, TSP-DDS, TSP-DTS, TSP-HIS, TSP-MWS and TSP-DVS sensors. Can also support the TSP-ULS, TSP-UHS, and the TSP-HLS. $1,009.00

TS-420IB 8 input 4-20 mA module, LSU500 transducers and VPS and SCCM pressure sensors $886.00

Non-Intrinsically Safe ModulesModel Description ListTS-ACI 12 input AC input module, dispenser hook inputs $847.00

TS-RLY 8 output relay module, SCCM solenoid and STP control $855.00

TS-10ARLY 6 output 10 Amp relay output module, dispenser power $568.00

TS-IO Input output module, 4 output 4-20 mA, 8 input 3-240 VAC/DC $886.00

TS-420EXP 8 input 4-20 mA module, LSU500E transducers and external devices $886.00

Note: TS-RLY Module is not required for STP control when utilizing turbine pump interface (TPI) communications.

The TS-420EXP module requires Controller Module software version 9.5 or greater

Do not include power supply and controller module when calculating total modules allowed.

TS-LS500 AutoLearn™ with Statistical Line Leak DetectionIntrinsically SafeFor new installations where separate low voltage conduits can be used. Use TS-420IB module.

Model Description ListTS-LS500/2 2-line transducer kit $1,271.00

TS-LS500/3 3-line transducer kit $1,862.00

TS-LS500/4 4-line transducer kit $2,449.00

Explosion ProofFor retrofit installations where only a high voltage conduit can be used. Use TS-420EXP module.

Model Description ListTS-LS500E/2 2-line transducer kit, explosion proof $1,271.00

TS-LS500E/3 3-line transducer kit, explosion proof $1,862.00

TS-LS500E/4 4-line transducer kit, explosion proof $2,449.00

Alternative Fuels AccessoriesModel Description ListTS-AFALNIP Leak generator needle valve kit required for E85 installations $90.00

Note: Using turbine pump interface (TPI) communications eliminates the need for a TS-RLY module; FFS intelligent controllers required.

Note: Using turbine pump interface (TPI) communications eliminates the need for a TS-RLY module; FFS intelligent controllers required.

144

Dispenser Interface Module CablesModel Description ListTSP-WDCBL Wayne™ cable $120.00

TSP-TDCBL Tokheim™ cable $223.00

TSP-GDCBL Gilbarco™ cable $269.00

TSP-GSDCBL Gilbarco™ G-Site™ cable $154.00

TSP-BDCBL Bennett® 515 only cable $194.00

Paper SuppliesThermal Printer SuppliesModel Description List

TS-TP2 One box of 5 rolls thermal printer paper for the T5 Series, and Tank Sentinel® consoles. $50.00

TS-TP2C One case (100 rolls) of thermal printer paper for the T5 Series, and Tank Sentinel consoles. $570.00

Impact Printer SuppliesModel Description ListTS-TP5000 TS-550 and TS-5000 impact printer paper $18.00

TS-TP5000C 12 rolls of impact printer paper $77.00

TS-INKRB TS-550 and TS-5000 ink ribbon $18.00

Secondary Containment MonitoringSensor ModulesModel Description ListTS-SCCM/1 Single channel secondary containment control module $1,130.00

TS-SCCM/2 Dual channel secondary containment control module $2,015.00

TS-SCMCAL Leak generator kit, one per station $82.00

VS-SCCM/1 220 VAC single channel secondary containment control module $1,130.00

VS-SCCM/2 220 VAC dual channel secondary containment control module $2,015.00

Install KitModel Description ListTSP-SCLSI Product, vapor line and sump containment install kit $151.00

TSP-SCTK2 Tank containment install kit for 2” risers, in-tank hose sold separately $151.00

TSP-SCTK2B Tank containment install kit for 2” risers with BSP threads, in-tank hose sold separately $151.00

TSP-SCTK4 Tank containment install kit for 4" risers, in-tank hose sold separately $167.00

TSP-SCTK4B Tank containment install kit for 4” risers with BSP threads, in-tank hose sold separately $167.00


Gilbarco™ and G-Site™ are trademarks of Gilbarco Inc. Tokheim™ is a trademark of Tokheim Holding B.V.

Note: T5 Series consoles shipped after 8/2010 have thermal printers.

145

AccessoriesModel Description ListTSP-SCBRB Five 1/4" NPT barbed fittings $23.00

TSP-SCBRBT 1/4" NPT barbed T-fitting $17.00

TSP-SCCLP Five hose clamps $69.00

TSP-SCTB25 25' hose $77.00

TSP-SCTB50 50' hose $132.00

TSP-SCTB100 100' hose $252.00

TSP-SCVLV Five Schreader valves $77.00

Upgrading Installed Fuel Management System ConsolesSoftware Version Upgrade OnlyModel Description ListTSA-UPGMS Software version upgrade shipped on a USB memory stick $120.00

146

Colibri Ordering Guide

CL6D/TRCL6 = Colibri Model

D = Display option

TR = Software Options

T = SCALD 24-hour tank testing

R = Reconciliation/autocalibration

Model Description ListCL6 Six channel Colibri console without display $1,352.00

CL6D Six channel Colibri console with display $1,789.00


CL-TT (T) Statistical Continuous Automatic Leak Detection (SCALD), 24 hour continuous tank testing software $1,151.00

CL-TRAC (R) Tank inventory reconciliation and autocalibration software $811.00

Model Description ListCL-UPGMS Coibri software version upgrade on a USB memory stick $114.00

Console model and software can be listed separately or combined when ordering. Systems shipped from the factory will list the combined part number. Complete console part numbers have a specific order and are created using the following guidelines:

Colibri Tank MonitorColibri Consoles


Software Upgrade

147


TEMSDPI/V TS-EMS console with display, printer, DIM, VRM software and one TS-PRB, TS-420IB and TS-10ARLY $8,782.00

TEMS2DPI/V TS-EMS console with display, printer, DIM, VRM software, one TS-PRB and TS-420IB, and two TS10ARLY $9,772.00

TEMS3DPI/V TS-DTU ready TS-EMS console with display, printer, DIM, VRM software, and one TS-10ARLY module $7,077.00

TEMSDPI/VS TS-EMS console with display, printer, DIM, VRM and SCM software, and one TS-PRB, TS-420IB and TS-10ARLY $9,546.00

TEMS2DPI/VS TS-EMS console with display, printer, DIM and SCM software, one TS-PRB and TS-420IB, and two TS-10ARLY $10,955.00

Notes: 1. Appropriate DIM cable must be ordered separately.

Model Description ListTS-MDMIB (M) Internal modem, includes fax and data software capability $798.00

Model Description ListTS-SCM (S) Secondary containment monitoring $1,152.00

Model Description ListTS-PRB 12 input probe module, VFM flow meters $847.00

TS-420IB 8 input 4-20 mA module, VPS and SCCM pressure sensors $886.00


TS-EMS Fuel Management System Console Interface ModulesIntrinsically Safe Modules

TS-EMS Environmental Monitoring System

2. TEMS and TEMS3 systems can support up to six dispensers. TEMS2 systems can support up to twelve dispensers. All models can be expanded to support up to 16 dispensers with additional modules.

3. The appropriate number of TS-VFM vapor flow meters and one TS-VPS vapor pressure sensor must be ordered separately to perform vapor recovery monitoring.

4. TS-ACI modules and hook signal wiring are only required for balance site installs.

TS-EMS Console Hardware and Software OptionsInternal Hardware Options

The TS-EMS environmental monitoring system comes standard with display, printer and dispenser interface module. An internal TS-MDMIB modem can be added as a hardware option. Order the TEMSDPI/VS if the secondary containment monitoring software option is required.

TS-EMS Environmental Monitoring System Ordering Guide

148

Non-Intrinsically Safe ModulesModel Description ListTS-RLY 8 output relay module, low power dispensers and SCCM solenoids $855.00

TS-10ARLY 6 output 10 Amp relay output module, high power dispensers and SCCM solenoids$568.00

Model Description ListTS-DTU/P Data transfer unit for wired-less VFM and VPS communications $1,233.00

Model Description ListTSP-WDCBL Wayne™ cable $120.00

TSP-TDCBL Tokheim™ cable $223.00

TSP-GDCBL Gilbarco™ cable $269.00

TSP-GSDCBL Gilbarco™ G-Site™ cable $154.00

TSP-BDCBL Bennett® 512 cable $194.00

Model Description ListTS-VFM Vapor flow meter, one per dispenser $1,653.00

TS-VPS Vapor pressure sensor, one per site $1,278.00

VRMEO202 Vapor recovery monitoring software (Vac Assist) $4,720.00

VRMEO204 Vapor recovery monitoring software (Balance) $4,720.00

TS-DTU/P Data transfer unit for wiredless VFM and VPS communications $1,233.00

TS-DRK/A Gilbarco™ Advantage dispenser retrofit install kit $138.00

TS-DRK/E Gilbarco™ Encore™ dispenser retrofit install kit $138.00

TS-DRK/T Tokheim™ dispenser retrofit install kit $138.00

TS-DRK/W Wayne™ dispenser retrofit install kit $138.00

7. Please supply the EO the site will be installed under.

Wayne™ is a trademark of Dresser Equipment Group Inc.


Gilbarco™ and Encore™ are trademarks of Gilbarco Inc.

Gilbarco™ and G-Site™ are trademarks of Gilbarco Inc. Tokheim™ is a trademark of Tokheim Holding B.V.

6. TS-ACI modules and hook signal wiring are only required for balance site applications.

3. TS-VRM software is included in the TS-EMS console.

4. Order one TS-DTU/P and one TS-DRK/x install kit per dispenser. Order one additional TS-DTU/P for the console. Controller Module software 9.5 or greater required.

5. Consoles using the wiredless option do not require the TS-PRB or TS-420IB modules for communication with the TS-VFM and TS-VPS

In-Station Diagnostics (ISD)

Notes: 1. Approved by California Air Resources Board EO VR-202 & VR-204

2. Minimum module requirements include one TS-PRB, TS-420IB, TS-RLY or TS-10ARLY.

External Modules

Note: Order one TS-DTU/P and one TS-DRK/x install kit per dispenser. Order one additional TS-DTU/P for the console.

Dispenser Interface Module Cables

149

TS-1001 Ordering Guide

XX PM/ABCCLRT1 = Model

T1 = TS-1001, 120 VACPM = Hardware Options

P = Printer, standard

M = Internal modemABCCLR = Software Options

A = 0,2, 4 tanks

B* = S, SCALD or G, generator

C** = D - data, F - fax/data software

C = Continental version

L = Line leak detection

R = Reconciliation

*SCALD and generator options are mutually exclusive, the SCALD option is not needed for the generator model.

**Data and fax/data modem options are mutually exclusive.

TS-1001 Full Feature Compliance ConsolesTS-1001, 110 VAC ModelsModel Description ListT1P/0 Leak monitor with 12 sensor inputs and printer $3,069.00

T1P/2 ATG, up to 2 tanks with 12 sensor inputs and printer $3,167.00

T1P/4 ATG, up to 4 tanks with 12 sensor inputs and printer $3,479.00

Console model, software and hardware options can be listed separately or combined when ordering. Systems shipped from the factory will list the combined part number. Complete console part numbers have a specific order and are created using the following guidelines:

150

XX PM/2GBCT1 = Model



M = Internal modem2GBC = Software Options

B* = D - data, F - fax/data software


Model Description ListT1P/2G One to two tank configuration with generator back-up capability (110 VAC) $3,449.00

TS-1001/G Ordering Guide

**Data and fax/data modem options are mutually exclusive.

TS-1001/G Fixed Feature Generator Tank Monitoring ConsoleTS-1001/G, 110 and 220 VAC Models


151

XXXX PM/YABCT750 = Model



M = Internal modemYABC = Software Options

Y = 1, 2, 3 or 4 tanks

A = S, SCALD

B* = D - data, F - fax/data software


Model Description ListT750P/1 Single tank kit with 8 sensor inputs and printer $4,225.00

T750P/1S Single tank kit with 8 sensor inputs, printer and SCALD $5,475.00

T750P/2 Two tank kit with 8 sensor inputs and printer $5,691.00

T750P/2S Two tank kit with 8 sensor inputs, printer and SCALD $6,941.00

T750P/3 Three tank kit with 8 sensor inputs and printer $8,129.00

T750P/3S Three tank kit with 8 sensor inputs, printer and SCALD $9,379.00

T750P/4 Four tank kit with 8 sensor inputs and printer $9,756.00

T750P/4S Four tank kit with 8 sensor inputs, printer and SCALD $11,006.00

Note: The TS-750 kit prices include 4" floats and install kits. 2" floats and install kits are available for an additional cost. Contact FFS Customer Service for pricing.


TS-750 Ordering Guide

*Data and fax/data modem optios are mutually exclusive

TS-750 Fixed Feature Tank Monitoring and Compliance KitsTS-750 110 VAC Models

152

Model Description ListTSSP-FDM2 (M) Internal modem, see software enhancements $469.00


TS-SCALD (S) Statistical Continuous Automatic Leak Detection, 24 hour continuous tank testing software $1,250.00

TS-DOM2 (D) Data only modem software $169.00

TS-FM2 (F) Fax and data modem software $636.00

TS-LLDI (L) Line leak detector interface software $987.00

TS-Reconciliation (R) Dispenser reconciliation software $169.00

Model Description ListTS-TP2 One box of 5 rolls of thermal printer paper for Tank Sentinel® consoles $50.00

TS-TP2C One case of 20 boxes of 5 rolls of thermal printer paper for Tank Sentinel® consoles $570.00

Tank Sentinel® Console AccessoriesInternal Console Hardware Enhancements

Console Software Enhancements

Paper Supplies

153

Model Description ListS940 Four channel sensor alarm console $1,217.00

S940 Sensor Alarm Console

154

Model Description ListTS-LS300/2 2-line console with line calibration kit $2,690.00

TS-LS300/3 3-line console with line calibration kit $3,903.00

TS-LS300/4 4-line console with line calibration kit $5,115.00

Model Description ListVS-LS300/2 2-line console with line calibration kit $2,664.00

VS-LS300/3 3-line console with line calibration kit $3,866.00

VS-LS300/4 4-line console with line calibration kit $5,066.00

For connecting two AutoLearn™ consoles togetherModel Description ListTSSP-ALICBL AutoLearn™ interface cable $68.00

Model Description ListTS-AFALNIP Leak generator needle valve kit required for E85 installations $90.00

Line Sentinel™Model Description List

TS-LLD/FE Electronic line leak detector with an FE Petro installation adapter, one required for each submersible pump $1,735.00

TS-LLD/RJ Electronic line leak detector with a Red Jacket™ installation adapter, one required for each submersible pump $1,735.00

TS-LLD/RJQ Electronic line leak detector with a Red Jacket™ Quantum™ installation adapter, one required for each submersible pump $1,853.00

Red Jacket™ is a trademark of Veeder-Root Company. Quantum™ is a trademark of Gilbarco Inc.

Alternative Fuels Accessories

TS-LS300, 230 VAC 50/60 Hz ModelsIntrinsically SafeFor new installations where separate low voltage conduits can be used.

Note: All AutoLearn™ models include the TPI turbine pump interface module.

Interface Cable

TS-LS300 AutoLearn™TS-LS300, 115 VAC 50/60 Hz ModelsIntrinsically SafeFor new installations where separate low voltage conduits can be used.

Note: All AutoLearn™ models include the TPI turbine pump interface module.

155

Leak Detection ProbesModel Description ListTSP-LL2-29 2' diameter tank probe $1,816.00

TSP-LL2-41 3' diameter tank probe $1,816.00



TSP-LL2-69 5'4" diameter tank probe $1,816.00










3. Float kits must be ordered separately.

Inventory Control ProbesModel Description ListTSP-LL2-29-I 2' diameter tank probe $1,246.00

TSP-LL2-41-I 3' diameter tank probe $1,246.00



TSP-LL2-69-I 5'4" diameter tank probe $1,246.00













Leak Detection and Inventory Control Probes

Notes: 1. Custom probe lengths are available; contact factory for price and delivery.

2. These probes are used with all Franklin Fueling Systems ATG consoles.

156

Model Description ListTSP-LL2-185-I 15' diameter tank probe $2,019.00



TSP-LL2-221-I 18" diameter tank probe $2,019.00

3. These probes are used with Franklin Fueling Systems ATGs.

4. Not for leak detection.

5. Float kits must be ordered separately.

6. Comes with bottom mount hardware. For replacement hardware kits, order TSSP-BMKT

Model Description ListTSP-MLGK-35 Standard gauge kit for vertical tanks up to 35' $3,785.00

TSP-MLGK-35-M Standard gauge for vertical tanks up to 35' with metric display $3,835.00

TSP-MLGKSS-35 Standard gauge for tanks up to 35' with stainless steel tape and float $4,207.00

TSP-MLGKSS-35-M Standard gauge for tanks up to 35' with metric display, with stainless steel tape and float $4,344.00

TSP-MLGK-50 Standard gauge for vertical tanks up to 50' $4,396.00

TSP-MLGKSS-50 Standard gauge for tanks up to 50' with stainless steel tape and float $4,686.00

TSP-MRFK-35 Retrofit gauge kit for vertical tanks up to 35' $2,490.00

TSP-MRFK-50 Retrofit gauge kit for vertical tanks up to 50' $2,865.00

Model Description ListFMP-FLX-4 4’ flexible inventory probe $2,451.00

FMP-FLX-5 5’ flexible inventory probe $2,451.00



FMP-FLX-8 8’ Flexible inventory probe $2,451.00















Moorman Level Gauge Kit

Note: 1. Orders for probes larger than 149" cannot be canceled and are non-returnable.

2. Probes longer than 149" may require special floats and install kits. Contact FFS for more information.

Inventory Control Probes continued

Flex Probes

157








































158









Model Description ListFMP-SLVF Installation kit, includes sleeve and adjustable height compression fitting $359.00

FMP-AGF2 2” gasoline float kit for flexible probes, includes product float, water float, and spacer $328.00



FMP-ADF2 2” diesel float kit for flexible probes, includes product float, water float, and spacer $328.00



Model Description ListTSP-IDF2 2" float set for diesel tanks $258.00

TSP-IGF2 2" float set for gasoline tanks $258.00

TSP-IDF4 4" float set for diesel tanks $165.00

TSP-IGF4 4" float set for gasoline tanks $165.00

TSP-LPGF 2" float for LPG tanks, with or without isolation sleeve $344.00

TSP-SSP 2-1/16" OD, #316 stainless steel float for chemical applications only $344.00

Note: Order one float set for each LL2 Mag probe.

Phase Separation Float KitsModel Description ListTSP-IGF4P 4" float set for gasoline and Ethanol blended tanks $413.00

TSP-IGF2P 2" float set for gasoline and Ethanol blended tanks $413.00

Density MeasurementStandardModel Description ListTSP-IDF4D3 Diesel/fuel oil density float kit $559.00

TSP-IGF4D3 Gasoline density float kit $559.00

Flex Probe Installation Kits & Float Kits

Float Kits

Notes: 1. Flexible Probe orders are noncancelable

159

Precision

Model Description ListTSP-IDF4D Diesel/fuel oil density float kit $837.00

TSP-IGF4D Gasoline density float kit $837.00

2. Standard density float kits accuracy: 3 kg/m3

3. Precision density float kits accuracy: 1 kg/m3. Requires TSP-LL2 Leak Detection probes and suspension install kits.

Suspension KitsModel Description ListTSP-K2A Leak detection probe install kit for 2" riser pipes $249.00

TSP-K2B Leak detection probe install kit for 2" riser pipes with BSP threads $249.00

TSP-K4A Leak detection probe install kit for 4" riser pipes $145.00

TSP-K4B Leak detection probe install kit for 4" riser pipes with BSP threads $209.00

Bottom Mount KitsModel Description ListTSP-C2A Inventory probe Install kit for 2” risers $188.00

TSP-C2B Inventory probe Install kit for 2” risers with BSP threads $180.00

TSP-C4A Inventory probe install kit for 4” risers $118.00

TSP-C4B Inventory probe install kit for 4” risers with BSP thread $148.00

Other KitsModel Description ListTSP-K4AS #316 stainless steel mag probe install kit for 4" riser pipes $308.00

TSP-K4ASL #316 SS mag probe install kit for 4" riser pipes and probes longer than 149" $308.00

TSP-LPGK LPG probe install kit, 149" maximum LL2 probe length $466.00

Note: TSP-LPGK install kit is not needed when locally supplied tank isolation sleeve is utilized.

Model Description List600-0042 Belden™ #87761, runs up to 500' (500' rolls) $2.00

600-0055 Belden™ #89182, runs 500' to 1,500' (500' rolls) $7.00

600-0180 Quick disconnect probe cable $50.00

3. Contact tech support for more information on cable requirements.

Probe Installation Kits

Cables

Notes: 1. Cable is sold in 500' increments.

2. Orders greater than 500' will ship in 1000' and 500' rolls.

Note: 1. Order one density measurement float kit for each magnetostrictive probe. Probes used with density float kits must have serial numbers greater than 6000000.

Belden™ is a trademark of Belden Technologies, Inc.

160

Model Description ListTSP-DB1 One direct burial splice connector kit $59.00

TSP-DB10 Pack of 10 direct burial splice connector kits $428.00

TSP-DBTOOL Epoxy dispensing tool $168.00

TSP-KW30 Pack of 30 3M™ splice connectors $66.00

TSP-UVPK Ultraviolet protection kit - protects probe electronics when installed in AST applications $69.00

Discriminating & Non-Discrimination Sensors

Model Description ListFMP-TEM Temperature sensor with installation fitting $830.00

Model Description ListTSP-HIS Hydrostatic interstitial Brite™ sensor, 11"* $600.00

TSP-HIS-XL Hydrostatic interstitial Brite™ sensor, 21"* $1,108.00

TSP-KV4 Hydrostatic sensor vented riser pipe cap kit for 4" riser pipes $110.00

Note: This sensor communicates with the console using 3 wires.

*Not including cable.

Model Description ListTSP-DIS Discriminating interstitial Brite™ sensor $505.00

TSP-KI2 Interstitial sensor riser cap kit for 2" riser pipes $110.00


Model Description ListTSP-EIS Electro-optic interstitial sensor $420.00



2. The DBTOOL is required to dispense the epoxy.

3. Each direct burial splice connector kit includes a receptacle, three splice connectors and epoxy for the dispensing tool.

TSP-HIS Hydrostatic Interstitial Brite™ Sensor

TSP-DIS Discriminating Interstitial Brite™ Sensor

TSP-EIS Electro-Optic Interstitial Sensor

3M™ is a trademark of 3M Company.

Temperature Sensor

Notes: 1. Use the TSP-DB1 or TSP-DB10 for direct burial cable applications or when weatherproof junction boxes are not used.

Accessories

161

Model Description ListTSP-HFS Horizontal Float Switch Sensor $414.00


Note: This sensor is for use with the S940 Sensor Alarm Console ONLY!

Model Description ListTSP-ULS Universal liquid sump sensor $238.00



Model Description ListTSP-UHS Universal Hydrostatic Sensor $238.00

HM-KIT Includes: flexible brine tube, sensor housing clamp, sensor housing, sensor cap and hardware $195.00


Model Description ListTSP-DMS-12 Discriminating magnetostrictive sensor, 12" $911.00

TSP-DMS-24 Discriminating magnetostrictive sensor, 24" $931.00

TSP-KS Uni-Strut® mounting kit $83.00

Model Description ListTSP-DDS Discriminating dispenser sump Brite™ sensor $488.00


Model Description ListTSP-DTS Discriminating turbine sump Brite™ sensor $575.00


Model Description ListTSP-DVS Discriminating vapor Brite™ sensor $596.00

TSP-KW4 Vapor sensor monitoring well pipe cap kit for 4" riser pipes $103.00

TSP-DDS Discriminating Magnetostrictive Sensor


TSP-DTS Discriminating Turbine Sump Brite™ Sensor


TSP-DVS Discriminating Vapor Brite™ Sensor


3. Requires Controller Module software version 9.5 or greater.

TSP-HFS Horizontal Float Switch Liquid Sensor

TSP-ULS Liquid Sensor

TSP-UHS Universal Hydrostatic Sensor

TSP-DMS Discriminating Magnetostrictive Sensor

Notes: 1. For use with the T5 Series fuel management systems.

2. This sensor communicates with the console via the TS-PRB probe module.

162

Model Description ListTSP-MWS-10 Monitoring well Brite™ sensor, 10' $814.00

TSP-MWS-15 Monitoring well Brite™ sensor, 15' $944.00

TSP-MWS-20 Monitoring well Brite™ sensor, 20' $1,076.00

TSP-MWS-25 Monitoring well Brite™ sensor, 25' $1,139.00

Model Description ListTSP-HLS-15 High product level sensor, 15" long, installed in tank $423.00

TSP-HLS-15/SS High product level sensor, stainless steel 15" long, installed in tanks containing alternative fuels $784.00

TSP-HLS-30 High product level sensor, 30" long, installed in tank $423.00

TSP-HLS-30/SS High product level sensor, stainless steel 30" long, installed in tanks containing alternative fuels $1,244.00

DC400 Dispensing Cutoff SystemModel Ordering Information

Model Description ListDC404 S404 float switch sensor and controller $595.00

TS-FE FE Petro STP electric junction box adapter $77.00

TS-RJ Red Jacket™ STP electric junction box adapter $77.00

TS-RJQ Red Jacket™ Quantum™ STP electric junction box adapter $77.00

Note: Electric junction box adapters for STP installations.

Model Description ListTSP-KI2 Interstitial sensor riser cap kit for 2" riser pipes $110.00

Model Description ListTSP-KV4 Hydrostatic sensor vented riser cap kit for 4" riser pipes $110.00

Model Description ListTSP-KW4 Interstitial/monitoring well pipe cap kit for 4" riser pipes $103.00

Model Description ListTSP-KS Uni-Strut® mounting kit for TSP-DDS and TSP-DTS sensors $83.00

TSP-HLS Level Sensor

TSP-MWS Monitoring Well Brite™ Sensor


TSP-K12 Interstitial Sensor Riser Cap Installation Kit

TSP-KV4 Hydrostatic Sensor Vented Riser Cap Installation Kit

TSP-KW4 Interstitial/Monitoring Well Pipe Cap Installation Kit

Sensor Installation AccessoriesUni-Strut® Mounting Kit

Red Jacket™ is a trademark of Veeder-Root Company. Quantum™ is a trademark of Gilbarco Inc.


163

Model Description ListTSP-DB1 One direct burial splice connector kit $59.00

TSP-DB10 Pack of 10 direct burial splice connector kits $428.00

TSP-DBTOOL Epoxy dispensing tool $168.00

TSP-KW30 Pack of 30 3M™ splice connectors $66.00

Sensor Installation Accessories (3M™ is a trademark of 3M Company.)

Notes: 1. Use the TSP-DB1 or TSP-DB10 for direct burial cable applications or when weatherproof junction boxes are not used.

2. The DBTOOL is required to dispense the epoxy.

3. Each direct burial splice connector kit includes a receptacle, three splice connectors and epoxy for the dispensing tool.

164

Model Description ListTS-RA1 Standard intensity, tank overfill alarm with light and horn $520.00

TS-RK Remote tank overfill alarm acknowledge unit $378.00

Model Description ListTS-RA2 High intensity, tank overfi ll alarm with light and horn $579.00

TS-RK Remote tank overfill alarm acknowledge unit $378.00

Model Description ListTS-RK Remote tank overfill alarm acknowledge unit $378.00

Model Description ListTS-DIM/G Dispenser interface module/Gilbarco™ dispensers $1,717.00

TS-DIM/GS Dispenser interface module/G-site™ controller $1,717.00

TS-DIM/T Dispenser interface module/Tokheim™ dispensers $1,717.00

TS-DIM/W Dispenser interface module/Wayne™ dispensers $1,717.00

Model Description ListTS-TPI Turbine pump interface $882.00

Model Description ListTS-EPS Ethernet port enabling device for Tank Sentinel® consoles $1,398.00

TS-EPS-N Ethernet port enabling device with null modem cable for other ATG systems. Not required with fuel management system or Colibri consoles. $1,398.00

TS-EPS Ethernet Port Server

Note: The Ethernet port device allows remote access to tank gauge console through an Ethernet IP address.

External Console HardwareTS-RA1 Remote Audible and Visible Alarm Unit

TS-RA2 Remote Audible and Visible Alarm Unit

TS-RK Remote Alarm Acknowledge Unit

TS-DIM Dispenser Interface Module

Note: Not available with the TS-750 or Colibri consoles. Tokheim™ is a trademark of Tokheim Holding B.V.

TS-TPI Turbine Pump Interface

Note: Not available with the TS-750.

Wayne™ is a trademark of Dresser Equipment Group Inc. Gilbarco™ and G-Site are trademarks of Gilbarco Inc.

165

Model Description ListSS-SU5 1-5 Site Licenses $1,199.00

SS-SU20 1-20 Site Licenses $2,235.00

SS-SU100 1-100 Site Licenses $4,308.00

Model Description ListSS-TECH Distributor/technician version of System Sentinel $510.00

Model Description ListSSA-SU25 1-25 Sites License $5,291.00

SSA-SU50 1-50 Sites License $10,024.00

SSA-SU100 1-100 Sites License $16,434.00

SSA-SU10 Additional increments of 10 sites $2,514.00

3. An additional fee will be charged for optional on-site installation and training. The charge is $500 per day plus travel expenses.

4. The purchase of an annual maintenance contract is required for continued technical support and to receive any software updates. The maintenance fee is 15% of the list price of the user's system at the time of renewal.

System Sentinel Site Licenses

System Sentinel Tech Edition

Notes: 1. Price includes the first six months of technical support.

2. When placing order, the following information must be supplied alond with email address to issue a software license:

Company software will be licensed to

Address of company

Phone number of company

Contact name at company

3. Licenses may not be returned after purchase

Notes: 1. Price includes the first six months of technical support.

2. When placing order, the following information must be supplied along with email address to issue a software license:


Address of company




System Sentinel AnyWare Site Licenses

Notes:


1. When placing order, the following information must be supplied along with email address to issue a software license:


Address of company



166

Model Description ListGCA-POLL-IE Monthly polling of FFS Ethernet sites (per site) $20.00

GCA-POLL-IM Monthly polling of FFS modem sites (per site) $30.00

GCA-POLL-VE Monthly polling of Veeder-Root™ Ethernet sites (per site) $30.00

GCA-POLL-VM Monthly polling of Veeder-Root™ modem sites (per site) $40.00

GCA-EXPORT Monthly data export fee $50.00

GCA-ARCHIVE One time data archival fee $250.00

Get Connected AnyWare (Veeder-Root™ is a trademark of Danaher Corporation.)

167

Model Description ListTS-STS-2K Sump test system with two probes $14,694.00

TS-STS-3K Sump test system with three probes $16,275.00

TS-STS-4K Sump test system with four probes $17,855.00

Spare PartsT5 Series and TS-EMS ConsolesModel Description List

TSSP-10ARLY Spare 6 output 10 amp relay module $568.00

TSSP-2WSNS Spare 12 input 2-wire sensor module $886.00

TSSP-3WSNS Spare 8 input 3-wire sensor module $1,009.00

TSSP-420IB Spare 8 input 4-20ma module $896.00

TSSP-420EXP Spare 8 input EXP 4-20ma module $896.00

TSSP-ACI Spare 12 input AC input module $847.00

TSSP-IO Spare input output module $886.00

TSSP-PRB Spare 12 input probe module $855.00

TSSP-RLY Spare 8 output relay module $855.00

TSSP-PS Power supply module $1,113.00

TSSP-TMPTR Thermal printer assembly for TS-550, TS-5000, TS-EMS $683.00

TSSP-TRMBLK Package of 10 assorted terminal blocks $164.00

TSSP-EXPPS Expansion console power supply $1,070.00

TSSP-CM Spare controller module, fuel management system application only, no software options $1,152.00

TSSP-CM/R Replacement controller module, factory programmed with required options $1,152.00

TSA-CMUPG Upgrade kit for TSSP-CM in stock to add original options $116.00

TSSP-LCDIFB5x LCD display and interface board kit for TS-550, TS-5000 $886.00

TSSP-T550MB TS-550 motherboard (for use with TS-EMS also) $187.00

TSSP-T5000MB TS-5000 motherboard $271.00

TSSP-SP5FUSE Spare Fuse Kit $33.00

TSSP-T5MB TS-5 motherboard $93.00

TSSP-LCDIFB5 LCD display and interface board kit for TS-5 $886.00

TSSP-CM/EMS-202TSSP-CM/EMS-204

Spare controller module for TS-EMS, vapor recovery monitoring application only. Need to know CARB Executive Order# $1,152.00

TSSP-CM/EMSB Spare controller module for TS-EMS (balance site), VRM (1.1) application only $1,162.00

Common To All (TS-5 uses TSSP-PRB only)

TS-5/550/5000/ Only

TS-5 Only

TS-EMS Only


AccessoriesSump Test System Kit

168

EVO-CM Spare TS-550/5000 evo controller module, standard features only, no software options $1,220.00

EVO-CM/R Replacement TS-550/5000 evo controller module, factory programmed with options $1,220.00

EVO-CMUPG Upgrade kit for EVO-CM in stock to add original options $111.00

EVO-LCD Replacement color LCD display $921.00

EVO-IFB Replacement display/printer interface board $921.00

EVO-TMPTR Thermal printer assembly for TS-550/5000 evo $435.00

Colibri ConsolesModel Description ListCL-MBWD Replacement main board/display $1,661.00

CL-MBWD/R Replacement main board/display, factory programmed with required options $1,661.00

CL-MB Replacement main board (no display systems) $1,228.00

CL-MB/R Replacement main board (no display systems), factory programmed with required options $1,228.00

CL-CVRWD Replacement cover with display opening $92.00

CL-CVR Replacement cover without display opening $92.00

CL-MBUPG Upgrade kit for CL-MBWD in stock to add original options $113.00

Model Description ListTSSP-BAT 3 Volt lithium battery $78.00

TSSP-DSP1 Keypad/display PC board $654.00

TSSP-DSPKC1 Display/keypad cable $101.00

TSSP-ENCLK Enclosure lock and key $78.00

TSSP-PSTB4-SM Surface mount probe/sensor terminal board, serial numbers 100000 and higher $194.00

TSSP-PTR Printer assembly $896.00

TSSP-PTRC1 Printer cable $67.00

TSSP-SMSB4 Surface mount system PC board, 110 VAC, serial numbers 100000 and higher $2,624.00

TSSP-SPFUSE Spare fuse kit $67.00

TSSP-SVKT4-SM TS-504 and TS-750 service kit for surface mount boards* $3,385.00

VSSP-SMSB4 Surface mount system PC board, 220 VAC, serial numbers 100000 and higher $2,357.00

TS-550/5000 evo Only

Note: The serial number of the old main board must be provided when ordering the CL-MBWD/R. Provide the serial number of the old and new main boards when ordering the CL-MBUPG.

Note: TSSP-MSB4 boards are no longer available. Order TSSP-SMSB4 main board and TSSP-PSTB4-SM terminal board as replacements.

Note: The serial number of the old CM must be provided when ordering the TSSP or EVO -CM/R. Provide the serial number of the old and new CM when ordering the TSA or EVO -CMUPG.

*TSSP-SVKT4-SM includes one of the following: TSSP-SMSB4, TSSP-DSP1, TSSP-PSTB4-SM, TSSP-PTR, TSSP-PTRC1, TSSP-DSPKC1, TSSP-SPFUSE, TSSP-ENCLK and TSSP-BAT.

TS-504 and TS-750 Consoles

169










TSSP-SVKT8-SM TS-508 service kit for surface mount boards* $3,723.00











TSSP-SVKT1-SM TS-1001 service kit for surface mount boards $3,385.00

TSSP-T1KEY Replacement key $28.00


Note: TSSP-MSB8 boards are no longer available. Order TSSP-SMSB8 main board and TSSP-PSTB8-SM terminal board as replacement.

Note:TSSP-MSB8 boards are no longer available. Order TSSP-SMSB8 main board and TSSP-PSTB8-SM terminal board as replacement.


TS-508 Console

TS-1001 Console


170










TSSP-SVKT2-SM TS-2001 service kit for surface mount boards* $3,723.00


DC400Model Description List404-4 Controller $507.00

S404 Float Switch Sensor $236.00

Model Description List010-0072 Control unit terminal interface board $258.00

020-1503 Hardware kit $50.00

430-0010 0.5 Amp fuse $6.00

TS-CU Control unit $712.00

TS-FC Line filter capacitor $42.00

TS-FPU Face plate unit $530.00

TS-LSU Leak sensor unit $1,180.00

Note:TSSP-MSB8 boards are no longer available. Order TSSP-SMSB8 main board and TSSP-PSTB8-SM terminal board as replacement.

Note: Replacement parts are not compatible with legacy DC400 systems. Both controlled and sensor must be replaced. Order DC404 system to replace legacy components.

TS-2001 Console


TS-LLD

171

Model Description List600-0180 Transducer quick disconnect cable $50.00

TS-ALCAL 3.0 gph calibration kit $85.00

TS-ALFUSE AutoLearn™ fuse kit $48.00

TS-AFALNIP Alternative fuels needle valve kit $90.00

TS-ALNIP Needle valve kit $50.00

TS-LSU300 Intrinsically safe pressure transducer $498.00

TS-LSU300E Explosion proof pressure transducer $498.00

TSSP-ALDB2 2-line display board $104.00

TSSP-ALDB4 4-line display board $129.00

TSSP-ALMB2 2-line intrinsically safe main board, 110 VAC $1,572.00

TSSP-ALMB2E 2-line explosion proof main board, 110 VAC $1,530.00

TSSP-ALMB4 4-line intrinsically safe main board 110 VAC $1,710.00

TSSP-ALMB4E 4-line explosion proof main board 110 VAC $1,667.00

TSSP-ALPTRC Ribbon cable, display board to main board $6.00

TSSP-ALTPI TPI turbine pump interface board $627.00

VSSP-ALMB2 2-line I/S main board, 220 VAC $1,483.00

VSSP-ALMB4 4-line I/S main board, 220 VAC $1,506.00

Model Description List600-0180 Transducer quick disconnect cable $50.00

TS-ALCAL 3.0 gph calibration kit $85.00

TS-AFALNIP Alternative fuels needle valve kit $90.00

TS-ALNIP Needle and valve kit $50.00

TS-LSU500 Intrinsically safe 4-20 mA pressure transducer $488.00

TS-LSU500E Explosion proof 4-20 mA pressure transducer $488.00

Model Description List282-0027 Chain, including split ring $32.00

282-0058 Split ring $6.00

600-0200 Probe cable 50' $175.00

TS-PRB-1 12" leak test probe kit* $1,562.00

TS-STS Replacement STS console and case $9,782.00

TS-TP2 One box of 5 rolls of thermal printer paper $50.00

TSP-SSP Stainless steel probe float $344.00

STS-CASE STS probe case $1,120.00

STS-PRB-12 12" leak test probe $1,052.00

STS-REPAIR STS system repair $746.00

TS-STS Sump Test Kit

Note: For parts for the TS-STS unit itself, reference the TS-1001 parts list. Repair price includes labor and return shipping only. *Probe kit includes probe, fl oat, chain and cable.

TS-LS300

TS-LS500

172

Model Description List430-0033 3 amp fuse for TS-ROM2/4 or /8 $5.00TSP-ENCD Replacement encoder for TS-VFM $342.00

Accessories

173

Fuel And Vapor Transfer SolutionsBottom LoadingModel Description List88050002 API adapter, short stroke three position, no sight glass $482.0088050004 API adapter, short stroke three position, 3" bubbled sight glass $537.0088050005 API adapter, short stroke three position, 3" bubbled sight glass, no handle $432.0088050007 API adapter, short stroke three position, no sight glass, removable handle $496.0088033001 Female gravity drop adapter $165.0088041101 Male gravity drop adapter $119.0088043001 Mechanically-operated 90 degree emergency valve (Victaulic ™) $513.0088043201 Air assisted 90 degree emergency valve (Victaulic™) $708.00Victaulic™ is a trademark of Victaulic Company of America.

Vapor RecoveryModel Description List30130001 3" N.P.S.M. vapor recovery adapter with poppet $111.0030344404 4" N.P.S.M. vapor recovery adapter, no poppet $86.0030230011 Flanged vapor check valve $248.0088034301 Air-operated sequential vapor valve $406.00

Overfill PreventionModel Description List89040002 2-wire controller $918.0090822101 Optic socket $187.0089011001 Optic probe, 2-wire, 8" $200.00

Product Drop ElbowsModel Description List88049302 Product drop elbow with cam and groove adapter and sight glass $748.00

88045501 Product drop elbow with sight glass $658.00

88046501 Dual point vapor recovery elbow $481.00

88049001 Coaxial delivery elbow $1,167.00

AccessoriesModel Description List88015001 Three-way air interlock valve $93.00

88015002 Three-way air interlock valve with roller top $113.00

88015003 Three-way air interlock valve with offset actuator $118.00

88040301 API adapter dust cap $103.00

30420005 Vapor cap with chain-chevroned gasket $45.00

77432002 Vapor return hose coupler $194.00

78430003 Hose tube door $68.00

174

API Bottom Loading AdaptersModel Description List88050002 Short stroke three position, no sight glass $482.00

88050004 Short stroke three position, 3.5" sight glass $537.00

88050005 Short stroke, three position, no handle, 3" sight glass $432.00

88050007 Short stroke, removable handle, no sight glass $496.00

88012001 Dust boot air cylinder $42.00

88050701 Replacement poppet kit with handles $102.00

88050702 Replacement kit for bottom loaders with handles $90.00

API Bottom Loading Adapter Spare PartsModel Description List88050901 Poppet head $38.0088012701 Spring, poppet $7.501103938 O-ring $8.7588019101 Washer, fl at, 5/8" ID $3.5088050601 Latch dual $20.7588021501 Cam, loading arm $56.0088019001 Roller, cam $7.7588018901 Pin, roller cam $11.0088019801 Hex, permanent handle $24.7588010201 Spring, handle $5.7588050501 Handle, dual latching $73.0088050503 Handle, dual latching (Canada) $73.0088019201 Pin, latch $7.501103912 O-ring, cross shaft $4.751108604 Pin, 3/16", spirol $3.751117016 Cap screw, socket head ¼-20 x 2" $2.001103010 Cap screw, socket head, 10-24 x 5/8" $2.2588051201 Sight glass, 3.5” bubble $39.001103937 O-ring, sight glass, 3.5" bubble $4.00

Dust CapModel Description List88040301 API Bottom Loading Adapter Dust Cap $103.00

88020601 API Bottom Loading Adapter Gasket $10.50

175

Air Interlock ValvesThreeWay Air Interlock Valves Parts ListModel Description List88014501 Plug - Nut $8.50

88014801 Spring $2.25

88017101 Spool & O-ring Assembly $19.50

1109004 Retaining Ring $3.50

88014201 Dust Seal $7.50

88014401 Screw Adjuster 1.0" $11.50

88017102 Spool & O-ring Assembly, Roller Tip $25.00

88112001 Actuator - Offset $28.25

90012 880-150-01 Service Kit $36.00

90055 880-150-02 Service Kit $59.00

90056 880-150-03 Service Kit $46.00

ThreeWay Air Interlock ValvesModel Description List88011301 Screw Adjustor Assembly 1.5" Button $18.50

88015001 Three-way Air Interlock Valve $93.00

88015002 Three-way Air Interlock Valve, Roller Tip $113.00

88015003 Three-way Air Interlock Valve, Offset Actuator $118.00

SixWay Air Interlock Valves Parts ListModel Description List88014501 Plug - Nut $8.5088014801 Spring $2.2588025801 Spool & O-ring Assembly $25.751109004 Retaining Ring $3.5088014201 Dust Seal $7.50

SixWay Air Interlock ValvesModel Description List88025601 ¼" - 1” Button Six-way Air Valve $127.00

88025602 ¼" - 1” Roller Tip Six-way Air Valve $168.00

88025603 ¼" - 1” Duckfoot Six-way Air Valve $154.00

90020 Service kit for 880-256-01 $65.00

90059 Service kit for 880-256-02 $67.00

176

Air Interlock with Limit Switch Parts ListModel Description List88115601 Air Valve Assembly $88.001102104 *Nut - Hex Jam $2.2588115501 *Adapter - Valve to Switch $16.001100325 O-ring $1.251121902 Limit Switch $68.0090012 Service Kit for 880-155-01 $36.00

* Note: These items are components of Air Valve Assembly 88115601

Air Interlock with Limit SwitchModel Description List88015501 ¼" - 1” Button with Limit Switch $196.00

88015502 ¼" - 1” Roller Tip with Limit Switch $215.00

177

Gravity Drop AdaptersFemale Gravity Drop Adapter Parts ListModel Description List1112507 Groove Pin $3.7577411603 Cam Arm & Ring Assembly $13.001111001 S-Hook $2.2588011502 Double Loop Chain $3.5088020601 Gasket $10.5077420204 Gasket $8.50

Female Gravity Drop AdapterModel Description List88033001 Female Gravity Drop Adapter $165.00

88020601 Gasket - API End $10.50

77420204 Gasket - Hose End $8.50

Male Gravity Drop Adapter Part ListModel Description List88020601 Rubber Gasket $10.5088041201 4" Drop Adapter - Body Only $78.001112507 Groove Pin $3.7577411603 Cam Arm & Pull Ring Assembly $13.0088011502 Double Loop Chain $3.501111001 S-Hook $2.25

Male Gravity Drop Adapter

Model Description List88041001 3" Male Cam & Groove $132.00

88041101 4" Male Cam & Groove $119.00

88020601 Gasket - API End $10.50

178

Vapor Check ValvesThreaded Vapor Check Valve Parts ListModel Description List30030502 Vapor Recovery Adapter - 3" N.P.S.M. $77.0030030532 Vapor Recovery Adapter - 3" B.S.P.P. $78.001103915 O-ring $4.7530020301 Poppet $7.7530010501 Spring - Poppet $4.7530020501 Guide - Poppet Stem $5.001109002 Retaining Ring $7.5077020102 3" Gasket Cover $6.25

Threaded Vapor Check ValveModel Description List30130001 3" N.P.S.M. Vapor Recovery Adapter, with Poppet $111.0030130002 4" N.P.S.M. Vapor Recovery Adapter, with Poppet $111.0030130003 3" BSPP Vapor Recovery Adapter, with Poppet $111.0030333303 3" N.P.S.M. Vapor Recovery Adapter, no Poppet $84.0030344404 4" N.P.S.M. Vapor Recovery Adapter, no Poppet $86.00

Flanged Vapor Check Valve Parts ListModel Description List1109002 Retaining Ring $7.5030020501 Poppet Stem Guide $5.0030010501 Poppet Stem Guide $4.7530020301 4" Poppet Vapor Recovery Adapter $7.751101002 Pipe Plug $4.501121504 Sight Glass $19.751103915 O-ring $4.75

Flanged Vapor Check ValveModel Description List30230011 Flanged Vapor Check Valve with Sight Glass $248.00

30230012 Flanged Vapor Check Valve without Sight Glass $175.00

179

Vapor CapsVapor Caps Parts List 30420001,02,04,05Model Description List1102409 Spirol Pin $1.5030430501 Vapor Recovery Cover $11.00

Vapor CapsModel Description List30420002 Nylon Vapor Cap with Chain $48.00

30420004 Nylon Vapor Cap without Chain-Chevroned Gasket $40.00

30420005 Nylon Vapor Cap with Chain-Chevroned Gasket $45.00

30430102 Aluminum Vapor Cap with Chain $89.00

180

Vapor Return Hose Couplers Parts ListModel Description List77432002 774-CV 4" × 3" Assembly $194.0077432003 774-CV 4" × 4" Assembly $194.0077411201 Probe $8.7577420203 3" Gasket $8.2577420204 4" Gasket $8.501112507 Groove Pin $3.7577411603 Cam & Ring Assembly $13.00

181

AirOperated Sequential Vapor Valve Parts ListModel Description List1103403 Square Cut Seal Ring $5.0088034401 Sequential Vapor Valve Body Assembly $243.001100326 O-ring $4.7588026701 Mounting Assembly Flange $81.00

AirOperated Sequential Vapor ValveModel Description List88034101 Flanged without Hood for 16" Manhole $287.00

88034201 Threaded without Hood for 20” Manhole $287.00

88034301 Flanged with Hood for 16" Manhole $406.00

88034401 Vent Valve Only $243.00

88034501 Threaded with Hood for 20" Manhole $386.00

182

Hose Tube DoorsModel Description List78430003 6" Plain Door $68.00

78440003 8" Plain Door $82.00

183

Product Drop ElbowsProduct Drop Elbow Parts ListModel Description List88013601 Rear Arm Assembly $66.0088013901 Connecting Link $21.7588048201 Operating Handle $73.0088013501 Front Arm Assembly $64.0088015101 Sight Tube Spacer $7.7588016201 Sight Tube $56.0088014001 Sight Glass Seal $8.5088028401 4" Dia. Coupling Adapter $67.0088039601 3" Cam & Groove Adapter $64.0088028901 4" NPT Adapter $71.0088039701 3" NPT Adapter $63.001119001 Wave Spring $4.5088013801 Connecting Pin $11.0088014901 Shoulder Spacer $11.501119601 Screw - 3/8-16 × 1.5" Hex Socket $5.7588013802 Connecting Pin $11.001118801 High Alloy Groove Pin $2.251118601 Flanged Bushing $6.0088012101 Cam Assembly Insert $48.0088014101 Seal $8.50

Product Drop ElbowModel Description List88049301 Product Elbow Dual Point - No Adapter $656.00

88049302 4" Cam and Groove Adapter with Sight Glass 21" tall $748.00

88049303 3" Cam and Groove Adapter with Sight Glass $743.00

88049304 4" NPT Adapter with Sight Glass $649.00

88049305 3" NPT Adapter with Sight Glass $595.00

184

Product Drop Elbow Parts ListModel Description List88045901 Product Elbow Body $384.0088023701 Product Elbow Handle $21.751130801 Product Elbow Seal $8.501108605 Pin Spirol $4.7588031001 Locking “Right” Cam $62.0088023801 Handle Block $45.0088031002 Locking “Left” Cam $61.0088014001 Sight Tube Seal $8.5088016201 Sight Tube $56.0088028401 4" Cam & Groove Adapter $67.0088015101 Sight Tube Spacer $7.7588039601 3" Cam & Groove Adapter $64.0088024701 Adapter Flange Gasket $5.7588039701 3" NPT Adapter $63.00

Product Drop ElbowModel Description List88045001 Body Only $481.00

88045501 4" Male Cam & Groove with S.G. $658.00

88045502 3" Male Cam & Groove with S.G. $658.00

88045504 3" Male NPT with S.G. $513.00

88045505 4" Male NPT with S.G. $507.00

Dual Point Vapor Recovery Elbow Parts ListModel Description List1117012 #10 - 24 × ½" Socket Head Cap Screw $1.2588024601 Handle Retainer Block $10.0088039101 Vapor Elbow Locking Bar $32.001112607 Grooved (Straight) Pin $6.5087020001 Elbow Seal $36.0088024501 Locking Cam $11.001112601 Grooved (Straight) Pin $5.5088024701 Adapter Flange Gasket $5.7588039601 3" Coupling Adapter $64.0088039701 3" NPT Adapter $63.00

185

Dual Point Vapor Recovery ElbowModel Description List880-460-01 Body Only $425.00

880-465-01 3" Male Cam & Groove Adapter $481.00

880-465-02 3" Male NPT Adapter $413.00

Coaxial Delivery Elbow Parts ListModel Description List880-380-01 Flanged, Coaxial Elbow $118.00

880-482-01 Operating Handle $73.00

880-281-01 Gasket $17.00

880-229-01 Vapor Outlet Block Off Plate $19.00

880-282-01 Top Gasket $28.25

1100403 Rollpin - 1/8" × 1" $2.50

880-138-02 Connecting Pin $11.00

880-138-01 Connecting Pin $11.00

1119001 Wave Spring $4.50

1119601 Screw - 3/8", 16 × ½" Hex Socket $5.75

880-149-01 Shoulder Spacer $11.50

880-147-01 Shoulder Spacer $4.25

880-285-01 Fuel Connection Adapter $68.00

880-141-01 Coaxial Elbow Seal $8.50

880-146-01 Fuel Connection Seal $40.00

880-136-01 Rear Arm Assembly $66.00

880-135-01 Front Arm Assembly $64.00

880-121-01 Cam Assembly Insert $48.00

880-139-02 Long Connecting Link $20.75

880-396-01 Cam & Groove 3" Adapter $64.00

880-284-01 Cam & Groove 4" Adapter $67.00

880-162-01 Sight Tube $56.00

880-151-01 Sight Tube Spacer $7.75

880-140-01 Sight Tube Seal $8.50

880-247-01 Adapter Flange Gasket $5.75

880-289-01 4" NPT Adapter $71.00

880-397-01 3" NPT Adapter $63.00

Coaxial Delivery ElbowModel Description List880-490-01 Over and Under Tall 4" × 3" Cam & Groove $1,167.00

880-491-01 Side by Side 4" × 3" Cam & Groove $986.00

880-495-01 Body Only $859.00

880-490-02 Over and Under Tall 4" x 3" NPT $1,013.00

880-490-03 Over and Under Tall 4" NPT 3" Cam & Groove $1,196.00

186

AttachmentsGasket KitModel Description List88024801 Delivery elbow replacement gasket kit $14.00

Sight Glass KitModel Description List88024901 Delivery elbow replacement sight glass kit $40.00

3" Cam & Groove AdapterModel Description List88039601 Delivery elbow replacement 3" cam & groove adapter $64.00

4" Cam & Groove AdapterModel Description List88028401 Delivery elbow replacement 3" cam & groove adapter $67.00

3" NPT Male AdapterModel Description List88039701 Delivery elbow replacement 3" cam & groove adapter $63.00

4" NPT Male AdapterModel Description List88028901 Delivery elbow replacement 3" cam & groove adapter $71.00

Cam and Groove AdaptersModel Description List77421220 2" Cam and Groove Dust Cap $24.00

77421240 4" Cam and Groove Dust Cap $44.00

187

Emergency ValvesMechanically Operated 90 Degree Emergency Valve (Victaulic™) Parts ListModel Description List88042801 Emergency Valve Victaulic™ 4" Body $240.00

1135801 3/16” SYN PTFE Packing $7.75

1103920 O-ring FLC #2-114 $4.75

1109008 Spirol Retaining Ring $3.50

88024101 Cam Shaft $25.00

88024201 Stuffing Box Nut $19.75

88026401 Emergency Valve Retainer Assembly $90.00

1135701 Poppet Spring $7.75

88026301 Poppet Assembly $128.00

88023301 Cam $40.00

88026501 Cam Lever Assembly $61.00

1138801 Emergency Valve Sump Gasket $10.50

Victaulic™ is a trademark of Victaulic Company of America.

Mechanically Operated 90 Degree Emergency Valve (Victaulic™)Model Description List88043001 4" Standard Victaulic™ Outlet Seal $513.00


Mechanically Operated 90 Degree Emergency Valve (Flanged) Parts ListModel Description List88042901 Emergency Valve Flanged 4" Body $338.00

1135801 3/16" SYN PTFE Packing $7.75

1103920 O-ring FLC #2-114 $4.75


88024101 Cam Shaft $25.00

88024201 Stuffing Box Nut $19.75




88023301 Cam $40.00



Mechanically Operated 90 Degree Emergency Valve (Flanged)Model Description List88043101 4" Standard Flanged Outlet Seal $518.00

188

Air Assisted 90 Degree Emergency Valve (Victaulic™) Parts ListModel Description List88035002 Emergency Valve Air Cylinder $215.00

88042901 4" Victaulic™ Emergency Valve Body $338.00

1135801 3/16" SYN PTFE Packing $7.75

1103920 O-ring FLC #2-114 $4.75


88024101 Cam Shaft $25.00

88024201 Stuffi ng Box Nut $19.75





88023301 Cam $40.00


1152601 Fusible Metal Pipe Plug, 1/8-27" NPT $15.00

1149401 Male Push-on Hose Fitting $5.50

88015901 Rubber Hose - Push-on Fitting $2.50


Air Assisted 90 Degree Emergency Valve (Victaulic™)Model Description List88043201 4" Standard Victaulic™ Outlet Seal with External Air Cylinder $708.00


Air Assisted 90 Degree Emergency Valve (Flanged) Parts ListModel Description List88035002 Air Cylinder $215.00

88042801 4" Flanged Emergency Valve Body $240.00

1135801 3/16" SYN PTFE Packing $7.75

1103920 O-ring FLC #2-114 $4.75


88024101 Cam Shaft $25.00

88024201 Stuffi ng Box Nut $19.75





88023301 Cam $40.00


1152601 Fusible Metal Pipe Plug, 1/8-27" NPT $15.00

1149401 Male Push-on Hose Fitting $5.50

88015901 Rubber Hose - Push-on Fitting $2.50

189

Air Assisted 90 Degree Emergency Valve (Flanged)Model Description List88043301 4" Standard Flanged Outlet Seal with External Air Cylinder $724.00

3" Emergency ValveModel Description List88045601 Air Operated Valve $674.00

88044901 Cable Operated Valve $462.00

190

Side Seal Adapter Parts ListModel Description List88120201 Seal $29.2588110301 Release Lever Spring $2.5088120100 Release Lever Interlock $8.751145901 Pin, 0.125 × 0.875", Groove Type “E” $1.5088120001 Release Lever $28.25

Side Seal AdapterModel Description List88044501 Side Seal Adapter $176.00

Bulk Pneumatic Pressure Relief ValvesModel Description List88122601 2" Female Pressure Relief Valve - 20 lbs. $296.00

191

Optic Control SystemTwoWire ControllerModel Description List89040002 Controller Mounted in Waterproof Housing $918.00

89020002 Control Module Only $792.00

TwoWire Optic Overfill ProbesModel Description List89011001 Two-Wire Optic Overfill Probe. 8" $200.00

FiveWire Optic Overfill ProbesModel Description List89011201 Five-Wire Optic Overfill Probe. 8" $200.00

Probe Holder SolutionsModel Description List90826202 Probe Holder with 2" NPT Male Thread, Tall Cap $189.00

90826301 Probe Holder with 2" Cast Lock Nut $178.00

90820801 Tall Probe Holder Cover $57.00

89025702 Probe Holder with Probe Kit $366.00

Single Socket SolutionsModel Description List90821101 Thermistor Socket with Plastic Cap $217.00

90822101 Optic Socket with Plastic Cap $187.00

90811901 Plastic Cap Only $29.00

90811001 Thermistor Conversion Kit $129.00

90812001 Optic Conversion Kit $107.00

OCS Installation KitsModel Description List89016202 2 Compartment Kit $1,614.00

89016203 3 Compartment Kit $2,192.00

89016204 4 Compartment Kit $2,580.00

192

Wiring KitsModel Description List90831301 Three Compartment Wiring Kit $338.00

90831401 Four Compartment Wiring Kit $344.00

90831501 Five Compartment Wiring Kit $365.00

90831601 Six Compartment Wiring Kit $377.00

90813101 Watertight Fitting Only $5.75

90813206 100’ Seven Conductor Cable Only $293.00

90813203 25' 7-CON cable $80.00

193

FFS-0217 01-16

3760 Marsh Rd. • Madison, WI 53718, USATel: +1 608 838 8786 • Fax: +1 608 838 6433Tel: USA & Canada +1 800 225 9787 • Tel: UK +44 (0)1473 243300

franklinfueling.com

Tel: Mex 001 800 738 7610 • Tel: FR +33 (0)1 69 21 41 41 • Tel: CH +86 10 8565 4566

A Franklin Fueling Systems Brand

Date post:	09-Jun-2020
Category:	Documents
Upload:	others
View:	3 times
Download:	0 times

TOTAL SYSTEM SOLUTIONS PRICE LIST - Americas › media › 634811 ›...

Documents