TRACK BUILDINGGuide
Design 1Design 1
8 curved tubes3 speed tubes1 speed tube with door12 connectors
1
5
6
2
4
3
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1.Take 2 curved tubes and join together with a connector, attach a connector to each end
2. Add a speed tube to each end, attach a connector to each end
3. Add a curved tube to each end, attach a connector to each end
4. Add a curved tube to each end, twist them around to match photo. Attach a connector to each end
5. Add a speed tube to each end, attach a connector to each end
6. Add a curved tube to each end, join together with a connector
Design 2Design 2
8 curved tubes3 speed tubes1 speed tube with door12 connectors
1
5
6
7
2
4
3
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1. Join 4 curved tubes together with 3 connectors
2. Add a connector to each end
3. Add a speed tube to each end
4. Add a connector to each end then add a speed tube
5. Add a connector to each speed tube
6. Join 4 more tubes together with 3 connectors as in step #1
7. Join to the connectors from step #5
8. Twist into shape
Design 3Design 3
8 curved tubes3 speed tubes1 speed tube with door12 connectors
1
5
6
2
4
3
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1. Join 4 curved tubes together with 3 connectors, attach a connector to each end
2. Add a speed tube to each end, attach a connector to each end
3. To one end add a speed tube, attach a connector to the end
4. Add a curved tube, attach a connector to the end, add a 2nd curved tube, attach a connector to the end
5. Add a speed tube, attach a connector to the end
6. Add a curved tube, attach a connector to the end, add a 2nd curved tube, attach to the open connector end of step #2
DESIGN 4DESIGN 4RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1. Take 2 curved tubes and join together with a connector. Attach a connector to each end
2. Add a speed tube to each end, attach a connector to each
3. To one end add a speed tube, attach a connector to the end
4. Add a curved tube, attach a connector to the end then add a second curved tube with a connector
5. Add a speed tube with a connector at the end
6. Add a curved tube with a connector on the end, then attach a second curved tube with a connector on the end, add a 3rd curved tube with a connectorat the end, then add a 4th curved tube to the end
7. Join together to the open end of the connector from step #2
8 curved tubes3 speed tubes1 speed tube with door12 connectors
1
5
6
2
2
4
3
design 5design 5RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1. Take a speed tube and attach a connector to each end
2. Add a curved tube to each end, attach a connectorto each end
3. Add a speed tube to each end, attach a connector to each end
4. To one end add a curved tube with a connector on the end
5. Add a speed tube with a connector on the end
6. Add a curved tube with a connector on the end, adda 2nd curved tube with a connector on the end, adda 3rd tube with a connector on the end, add a 4th curved tube with a connector at the end, then a 5thcurved tube with a connector on the end
7. Join together to the open connector end of step #3
1
5
6
7
2
43
8 curved tubes3 speed tubes1 speed tube with door12 connectors
design 6design 6
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1. Take 2 curved tubes and join together with a connector, attach a connector to each end
2. Add a speed tube to each end, attach a connector to each end
3. To one end add a curved tube, attach a connector to the end, add a 2nd curved tube and attach a connector to the end
4. Add another curved tube with a connector on the end, but twist around to face the opposite direction then the curved tubes on step #3
5. Add a curved tube, attach a connector to the end
6. Add a speed tube, attach a connector to the end
7. Add a curved tube, attach a connector to the end, then add a 2nd curved tube and attach a connector to the end
8. Add a speed tube & join together to the open end of the connector from step #2
1
5 6
7
8
2
2
4
3
8 curved tubes3 speed tubes1 speed tube with door12 connectors
design 7design 7
8 curved tubes3 speed tubes1 speed tube with door12 connectors
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1. Take 2 curved tubes and join together with a connector, attach a connector to each end
2. Add a speed tube to each end, attach a connector to each end
3. To one end add a curved tube, attach a connector to the end, add a 2nd curved tube and attach a connector to the end
4. Add another curved tube with a connector on the end, but twist around to face the opposite directionthen the curved tubes on step #3
5.Add a curved tube, attach a connector to the end
6. Add a speed tube, attach a connector to the end
7. Add a curved tube, attach a connector to the end, then add a 2nd curved tube and attach a connector to the end
8. Add a speed tube & join together to the open end of the connector from step #2
Build as Design 6 and then take circle #1 and bring up to a vertical position:
circle 1
circle 2
design 8design 8
8 curved tubes3 speed tubes1 speed tube with door12 connectors
1. Take a speed tube & attach a connector to each end. Add a curved tube to each end. Attach a connector to each end
2. Add a curved tube to each end, attach a connectorto each end
3. To one end add a speed tube, attach a connector to the end. Add a 2nd speed tube, attach a connector to the end
4. Add a curved tube, attach a connector to the end
5. Add a speed tube, attach a connector to the end
6. Add a curved tube, attach a connector to the end. Add a 2nd curved tube, attach a connector to the end. Add a 3rd curved tube, twist it around in the other direction and attach to the open end from step #2
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
6
5
1
1
1
2
2
3
4
design 9design 9
11 curved tubes4 speed tubes2 straight tubes9 connectors1 criss-cross-crash connector
1
1
5
6
2
2
4
3
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1. Take a speed tube, attach a connector to each end.Add a curved tube to each end, attach a connectorto each end
2. Add a speed tube to each end, attach a connector to each end. Add a curved tube to each end, attacha connector to each end
3. To one end add a speed tube, attach a connector to each end
4. Add a curved tube, attach a connector to the end. Then add a 2nd curved tube, attach a connector to the end. Then add a straight tube, attach a connector to the end, and join to a criss-cross-crash connector
5. To the open end from step #2, attach a connector to the end and join to the criss-cross-crash open arm next to the one from step #4
6. To one open arm of the criss-cross-crash, attach aconnector, add a curved tube, attach a connector to the end, add a 2nd curved tube, attach a connector to the end, add a straight tube, attach a connector to the end, add a 3rd curved tube, attach a connector to the end, add a 4th curved tube, attach a connector to the end and the join to the last open arm of the criss-cross-crash connector
TUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT
&&*multiple sets required
design 10design 10
12 curved tubes6 speed tubes2 straight tubes22 connectors1 criss-cross-crash connector
11
1
5
6
7
8
2
2
2 24
3
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1. Take a curved tube, attach a connector to each end. Add a speed tube to each end, attach a connector to each end
2. Add a curved tube to each end, attach a connector to each end. Add a speed tube to each end, attach a connector to each end
3. To one end attach a curved tube, attach a connector to the end. Add a 2nd curved tube, twist it around and attach a connector to the end, join to a criss-cross-crash connector
4. To the other end, add a speed tube, attach a connector to the end
5. Add a curved tube, attach a connector to the end, add a 2nd curved tube, attach a connector to the end, and then add a 3rd curved tube, attach a connector to the end
6. Add a speed tube, attach a connector to the end, add a straight tube, attach a connector to the end,connect to the criss-cross-crash arm that is next to the one in step #3
7. To one of the open arms of the criss-cross-crash,attach a connector, add a curved tube, attach a connector to the end, add a 2nd curved tube, attacha connector to the end
8. Add a straight tube, attach a connector to the end,then add a curved tube, attach a connector to the end, then add a 2nd curved tube, attach a connector to the end. Join to the last open arm of the criss-cross-crash
TUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT
&&*multiple sets required
DESIGN 11DESIGN 11
1
5
6
6
2
4
4
3
3
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
TUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT
&&
12 curved tubes6 speed tubes1 straight tube22 connectors1 criss-cross-crash connector
1. Take 2 curved tubes and join them together with a connector, attach a connector to each end
2. To one end, add a curved tube, twist it around in the opposite direction, attach a connector to the end. Attach a 2nd curved tube, twist it in the opposite direction, attach a connector to the end.Join to a criss-cross-crash connector
3. To the open end of step #1, add a speed tube, attach a connector to the end, add a curved tube, attach a connector to the end. Add another speed tube, attach a connector to the end. Add a 3rd speed tube, attach a connector to the end. Join tothe criss-cross-crash connector
4. To one open arm of the criss-cross-crash connector, add a speed tube, attach a connector to the end. Add a curved tube, attach a connectorto the end. Add a 2nd curved tube and attach a connector to the end
5. Add a curved tube, attach a connector to the end,add a 2nd curved tube, twist it around and attacha connector to the end, add a 3rd curved tube, attach a connector to the end. Add a 4th curved tube and attach a connector to the end
6. Add a speed tube, attach a connector to the end. Add a 2nd speed tube, attach a connector to the end. Add a curved tube, attach a connector to theend. Add a straight tube, attach a connector to the end and join to the last open arm of the criss-cross-crash connector
*multiple sets required
design 12design 12
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1
5
6
7
89
2
2 4
3
1. Join 3 curved tubes together with 2 connectors. Attach a connector to each end
2. Add a speed tube to each end, attach a connector to each end
3. To one end add a straight tube, attach a connector to the end. Then attach a criss-cross-crash connector
4. To the other end, add a speed tube, attach a connector to the end
5. Add a curved tube, attach a connector to the end
6. Add a speed tube, attach a connector to the end
7. Add a curved tube, attach a connector to the end
8. Add a speed tube, attach a connector to the end
9. Add a curved tube, attach a connector to the end
10. Add a speed tube, attach a connector to the end
11. Add a curved tube, attach a connector to the end. Add a 2nd curved tube, attach a connector to the end, join to the open arm of the criss-cross-crash connector (the one opposite the arm joined in step #3)
12. To one open arm of the criss-cross-crash connector, add a curved tube, attach a connector to the end, add a2nd curved tube, attach a connector to the end, add a straight tube, attach a connector to the end, add a 3rd curved tube, attach a connector to the end, then add a 4th tube, and attach a connector to the end. Join to thelast open arm of the criss-cross-crash connector
TUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT&&
12 curved tubes6 speed tubes2 straight tubes22 connectors1 criss-cross-crash connector
10
11
12
*multiple sets required
DESIGN 13DESIGN 13
12 curved tubes7 speed tubes2 straight tubes22 connectors1 criss-cross-crash connector
15
66
6
7
8
9
10
24
3
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1. Take 3 curved tubes and join together with 2 connectors. Add a connector to each end
2. To one end add a straight tube, attach a connector to the end
3. Add a curved tube, attach a connector to the end, add a 2nd curved tube and attach a connector to the end
4. Add a curved tube, twist it in the opposite direction of the curved tubes in step #3. Attach a connector to the end
5. Add a speed tube, attach a connector to the end. Then connect to a criss-cross-crash connector
6. To the open end from step #1 add a speed tube, attach a connector to the end. Add a 2nd speed tube, attach a connector to the end. Add a straighttube, attach a connector to the end. Attach a 3rd speed tube, attach a connector to the end. Add a curved tube, attach a connector to the end, then join to the criss-cross-crash connector arm
7. To another open arm of the criss-cross-crash connector add a curved tube, attach a connector to the end. Add a 2nd curved tube and twist it in the opposite direction of the curved tubes in step #6, attach a connector to the end
8. Add a curved tube, attach a connector to the end. Add a 2nd curved tube, attach a connector to the end
9. Add a speed tube, attach a connector to the end. Add a curved tube, attach a connector to the end
10. Add a speed tube, attach a connector to the end. Add a 2nd speed tube, attach a connector to the end. Join to the last open arm of the criss-cross-crash connector
TUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT&& *multiple sets required
Design 14Design 14
12 curved tubes11 speed tubes2 straight tubes26 connectors
11
5
5
6
6
7
8
9
2
2
4
3
3
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
1. Join 9 speed tubes together with 8 connectors. Attach a connector to each end
2. Add a curved tube to each end, attach a connectorto each end
3. Add a straight tube to each end. Attach a connector to each end
4. Add a curved tube to each end. Attach a connectorto each end
5. Add a speed tube to each end. Attach a connector to each end
6. Add a curved tube with a connector to each end Then add another curved tube to each end. Add a connector to each end
7. On one end add a straight tube with a connector atthe end
8. Add a curved tube with a connector on the end, then a second tube with a connector on the end. Add a 3rd tube, then add a final 4th curved tube with a connector on the end
9. Join to the open connector from step #6
TUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT&&*multiple sets required
Design 15Design 15
12 curved tubes17 speed tubes3 straight tubes36 connectors2 criss-cross-crash connectors
1
56
7
8
9
10
11 12
13
2
4
3
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
TUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT
1. Take a straight tube and attach a connector to each end
2. Add a curved tube to each end, then add a connector to each end
3. Add a speed tube to each end, attach connectors to each end
4. To one end (bottom) add a speed tube with a connector at the end
5. To the other (top) add a curved tube with a connector, add a speed tube with a connector and a second speed tube with aconnector on the end
6. Join together both with a criss-cross-crash connector
7. Make a second structure using the directions in steps #1-6
8. To make the middle structure: To each criss-cross-crash open top arm add a speed tube with a connector on the end, then add another speed tube with a connector on the end
9. Join together with a curved tube
10. To the open right arm from the criss-cross-crash from step #6, add a speed tube with a connector on the end, and then add a second speed tube with a connector on the end
11. Add a curved tube with a connector on the end, add a 2nd curved tube with a connector on the end, add a 3rd curved tube with a connector on the end, add a 4th curved tube with a connector on the end, & add a 5th curved tube with a connector on the end (this will make the circle structure)
12. To the last (5th) curved tube connector end add a speed tube with a connector on the end
13. Add a straight tube with a connector on the end and join to the open arm of the criss-cross-crash connector at step #7
&&*multiple sets required
9
Design 16Design 16
8 curved tubes16 speed tubes8 straight tubes36 connectors2 criss-cross-crash connectors
1
5
6
2
2 4
3
1.Take 2 straight tubes and join them togetherwith a connector, attach a connector to each end
2. Add a curved tube to each end. Attach a connector to each end
3. Add a speed tube to each side, attach a connector to each end. Then add another speed tube to each side. Attach a connector to each end
4. Repeat steps #1-3, three times more, for a total of 4 structures
5. Attach all 4 structures together with 2 criss-cross-crash connectors and twist into desired shape
RC CAR TRAX
SET KITRC CAR TRAX
SET KITTUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT&& *multiple sets required
Design 17Design 17
12 curved tubes8 speed tubes21 connectors5 straight tubes2 criss-cross-crash connectors
1
5
55
2
2
2
4
43
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
TUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT
1. Take a criss-cross-crash connector, attach a connector to each of the 4 arms
2. To one end add a curved tube, attach a connector to the end, add a 2nd curved tube, attach a connector to the end, add a 3rd curved tube, attach a connector to the end,add a 4th curved tube, attach a connector to the end, thenadd a straight tube, attach connector to the end, and 5th curved tube and join to the open end of the criss-cross-crash connector in step #1
3. To one of the other arms add a speed tube, attach a connector to the end, add a straight tube, attach a connector to the end, add a 2nd speed tube, attach a connector to the end, add a 2nd straight tube, attach a connector to the end, add a 3rd speed tube, attach a connector to the end, add a 4th speed tube, attach a connector to the end, join to a 2nd criss-cross-crash connector
4. Go back to the last open arm of the 1st criss-cross-crashconnector from step 1. Add a curved tube, attach a connector to the end, add a speed tube, attach a connector to the end, add a 2nd speed tube, attach a connector to the end, add a 3rd speed tube, attach a connector to the end, add a 4th speed tube,attach a connector to the end, add another curved tube and join to an open arm of the 2nd criss-cross-crash connector
5. To the open of the 2nd criss-cross-crash connecter, add acurved tube, attach a connector to the end, add a 2nd curved tube, attach a connector to the end, add a speed tube, attach a connector to the end, add a 3rd curved tube, attach a connector to the end, add another speed tube,attach a connector to the end, add a 4th curved tube,attach a connector to the end, add another speed tube, attach a connector to the end, add a 5th curved tube, attach a connector to the end, add a straight tube, attach a connector to the end, then join to the last open arm of the 2nd criss-cross-crash connector
&&
*multiple sets required
Design 18Design 18
12 curved tubes11 speed tubes6 straight tubes34 connectors2 criss-cross-crash connectors
1
1
5
5
5
5
5
6
2 2
2
2 4
44
33
3
RC CAR TRAX
SET KITRC CAR TRAX
SET KIT
TUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT
1. Take a speed tube, attach a connector to each end,add a curved tube, attach a connector to each end
2. To each side add a curved tube, attach a connectorto each end, add a straight tube to each end, attacha connector to the end, add a 2nd straight tube, attach a connector to the end, add a speed tube to each end, attach a connector to the end, then join each end to a criss-cross-crash connector
3. To each open bottom arm of the criss-cross-crash connectors, attach a connector, then add a curved tube to each side, attach a connector to each end, then join together with a straight tube
4. To one open arm of each side of the criss-cross-crash connector, add a straight tube, attach a connector to each end, add a curved tube to each side, attach a connector to each end. Join togetherwith a speed tube
5. To each of the last 2 open arms of the criss-cross-crash connector, add a speed tube to each side, attach a connector to each end. Add a curved tube,attach a connector to each end, add a 2nd speed tube to each side attach a connector to each end
6. Add a curved tube with a connector to each end. Join together with a speed tube
&&*multiple sets required
Design 19Design 19
10 curved tubes15 speed tubes4 straight tubes32 connectors2 criss-cross-crash connectors
1
56
2
4
3
1. Take a criss-cross-crash connector and add a connector to each arm
2. To one arm add a speed tube, attach a connector to the end
3. Add a curved tube and attach a connector to the end
4. Add a speed tube, attach a connector to the end, and then add a straight tube, attach a connector to the end
5. Add a curved tube, attach a connector to the end
6. Add a speed tube, attach a connector to the end, then attach to a 2nd criss-cross-crash connector
7. Repeat steps #2-6 and attach to the open arms of criss-cross-crash connectors
8. To one of the open arms of the first criss-cross-crash connectors, add a speed tube, attach a connector to the end. Add a 2nd speed tube, attach a connector to the end
9. Add a curved tube with a connector at the end
10. Take 4 speed tubes and connect these together with 3 connectors. Attach a connector to each end
11. Attach one end to the open connector at step #9. To theother connector end add a curved tube, attach a connector to the end
12. Add a straight tube and attach a connector to the end
13. Add a curved tube, attach a connector to the end, and then attach another curved tube with a connector to the end
14. Twist the last curved tube around and attach to the open arm of the criss-cross-crash connector from step #6
15. Go back to the last open arm from the first criss-cross-crash connector
16. Add a speed tube, attach a connector to the end, add a curved tube, attach a connector to the end, add a 2ndspeed tube, attach a connector to the end, add a straight tube, attach a connector to the end. Add a straight tube, attach a connector to the end. Add a 3rd speed tube and atach to the last open arm of the 2nd criss-cross-crash connector
RC CAR TRAX
SET KITRC CAR TRAX
SET KITTUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT&&
7
7
8
9
10
1112
13
14
16
16
*multiple sets required
15
DESIGN 20DESIGN 20
8 curved tubes2 criss-cross-crash connectors12 connectors
1.Take a criss-cross-crash connector and add connectors to each of the 4 arms. Add a curved tube to each connector, attach a connector to the end of the 4 curved tubes
2. Add a curved tube to each end. Add a connector to each and the attach all 4 to a 2nd criss-cross-crash connector
TUBULAR EXPANSION
TRAX KITTUBULAR EXPANSION
TRAX KIT *multiple sets required
1
2