TRADING - Macsteel · TRADING The Macsteel Group - Africa’s leading steel supplier - PIPES,...

PIPES AND FITTINGS CATALOGUE

T R A D I N G

The Macsteel Group - Africa’s leading steel supplier - www.macsteel.co.za

T R A D I N G

T R A D I N G


PIPES, FITTINGS & FLANGES - CONTENTS

1E&OE

CATEGORY SUBJECT PAGE

CARBON STEELPIPES ASTM A106 seamless 3 SANS 719 welded 6 SANS 62 welded, screwed and plain ended 7 Chemical composition 8 Dimension tolerances and pipe specifications 9 End preparation 9

FITTINGS Buttweld ASTM A234 Grade WPB 11 Buttweld JIS B 2311-09 19 Forged ANSI B 16.11 23 Pressure/Temperature ratings 26 Malleable cast EN 10242 27 EN 10241:2000 28

FLANGES Carbon steel ASTM A105 ASA 150lb 30 ASA 300lb 31 ASA 600lb 32 Tolerances 31 Steel plate BS EN 1092-1 : 2007 33 SANS 1123 : 2007 34 BS 10 : 1962 35

STAINLESS STEELMACSTEEL RANGE 37

PIPE Dimensions B36.19 and B36.10 38

FITTINGS AND FLANGES Specifications 39

GRADES 304/304L 41 316/316L 42

For information outside the scope of this reference publication, please contact our technical staff.

T R A D


PIPES2E&OE

ASTM A106 SEAMLESS I API 5L SEAMLESS/WELDED I SANS 719 WELDED I SANS 62 WELDED


3E&OEFor information outside the scope of this reference publication, please contact our technical staff.

PIPES - Dimensions for A106 - Seamless, API 5L - Seamless or Welded

T R A D I N G

6

8

10

15

20

25

32

40

50

65

80

90

100

125

NominalBoremm

10.3

13.7

17.1

21.3

26.7

33.4

42.2

48.3

60.3

73.0

88.9

101.6

114.3

141.3

Outsidediameter

mm1.732.412.243.022.313.202.773.734.787.472.873.915.567.823.384.556.359.093.564.856.359.703.685.087.14

10.163.915.548.7411.075.167.019.52

14.025.497.6211.1315.245.748.086.028.5611.1313.4917.126.559.52

12.7015.8819.05

Wallthickness

mm6.845.489.227.6612.4810.7015.7613.8411.746.3620.9618.8815.5811.0626.6424.3020.7015.2235.0832.5029.5022.8040.9438.1434.0227.9852.4849.2242.8238.1662.6858.9853.9644.9677.9273.6666.6458.4290.1285.44

102.2697.1892.0487.3280.06

128.20122.26115.90109.54103.20

Internaldiameter

mm0.360.460.630.800.851.101.271.621.942.561.682.192.893.642.503.234.235.453.384.465.617.744.055.407.229.555.437.4911.0913.458.6211.4014.9020.3811.2915.2521.3327.6613.5718.6216.0722.3128.2533.4940.9821.7830.9240.2449.0557.38

Masskg/m

approxSTDXS

STDXS

STDXS

STDXS

XXSSTDXS

XXSSTDXS

XXSSTDXS

XXSSTDXS

XXSSTDXS

XXSSTDXS

XXSSTDXS

XXSSTDXS

STDXS

XXSSTDXS

XXS

4080408040804080

160

4080

160

4080

160

4080

160

4080

160

4080

160

4080

160

4080

160

40804080

120160

4080

120160

Schedule




T R A D I N G

150

200

250

300

350

NominalBoremm

168.3

219.1

273.0

323.8

355.6

Outsidediameter

mm7.11

10.9714.2718.2421.956.357.048.18

10.3112.7015.0618.2420.6222.2223.016.357.809.27

12.7015.0618.2421.4125.4028.586.358.389.52

10.3112.7014.2717.3521.4125.4028.5833.326.357.929.5211.1312.7015.0619.0523.8027.7631.7535.71

Wallthickness

mm154.08146.36139.76131.82124.40206.40205.02202.74198.48193.70188.98182.62177.86174.66173.08260.30257.40254.46247.60242.88236.52230.18222.20215.84311.10307.04304.76303.18298.40295.26289.10280.98273.00266.64257.16342.90339.76336.56333.34330.20325.48317.50308.00300.08292.10284.18

Internaldiameter

mm28.2642.5654.1767.4979.1033.3136.7942.5353.1064.6375.8290.36

100.86107.78111.1641.7751.0060.2981.5495.90114.64132.88154.96172.0949.7265.2073.8279.7297.44

108.86131.89159.72186.75207.85238.5254.6867.9481.2894.40

107.38126.58157.95194.82224.42253.14281.38

Masskg/m

approxSTDXS

XXS

STD

XS

XXS

STDXS

XXS

STD

XS

XXS

STD

XS

4080

120160

2030406080

100120140

1602030406080

1001201401602030

40

6080

10012014016010203040

6080

100120140160

Schedule




T R A D I N G

400

450

500

550

600

NominalBoremm

406.4

457.2

508.0

558.8

609.6

Outsidediameter

mm6.357.929.52

12.7016.6621.4126.1930.9436.5340.466.357.929.5211.1312.7014.2719.0523.8029.3634.9239.6745.246.359.52

12.7015.0620.6226.1932.5438.1044.4549.996.359.52

12.7022.2228.586.359.52

12.7014.2717.3524.5930.9438.8946.0252.3759.51

Wallthickness

mm392.70390.56387.36381.00373.08363.58354.02344.52333.34325.48444.50441.36438.16434.94431.80428.66419.10409.60398.48387.36377.86366.72495.30488.96482.60477.88466.76455.62442.92431.80419.10408.02546.10539.76533.40514.36501.64596.90590.56584.20581.06574.90560.42547.72531.82517.56504.86490.58

Internaldiameter

mm62.6377.8693.21123.29160.05203.32245.32286.44332.62364.8570.5987.79105.14122.36139.19155.91205.62254.38309.44363.19408.01459.1878.54117.07155.10183.15247.78310.82381.04440.93507.54564.1486.50129.01171.01293.81373.8394.45140.88186.92209.54254.93354.74441.90546.92639.18718.94806.61

Masskg/m

approx

STDXS

STD

XS

STDXS

STDXS

STDXS

102030406080

1001201401601020

30

406080

100120140160102030406080

10012014016010203060801020

30406080

100120140160

Schedule



PIPES - SANS 719 Welded Pipes

200250300350400450500600700800900

219273324356406457508610711813914

Dimensions & Mass

NBmm

ODmm

88888888888

41.6352.2962.3568.6778.5388.6098.66118.79138.72158.84178.77

Wallmm

Masskg/m

66666666666

31.5339.5147.0651.8059.2066.7474.2989.39

104.33119.43134.37

Wallmm

Masskg/m

4.54.54.54.54.54.54.54.5

23.8129.8035.4639.0144.5650.2255.8867.21

Wallmm

Masskg/m

T R A D I N G200250300350400450500600700800900

219273324356406457508610711813914

Test Pressure KPa

Wall Thickness

Pressure Rating Grade B

NBmm

ODmm

1980015890133901220010670949085407120610053404750

121320010590893081307120633056904740407035603160

165001324011160101708900691071205930508044503960

8 1074305960502045804000356032002670229020001780

99007950670061005340475042703560305026702370

4.5 6



PIPES - SANS 62 Welded Pipes

8101520253240506580

100125150

13.316.821.126.633.442.148.059.875.488.1113.3138.7164.1

Dimensions

The outside diameter of a pipe is considered constant, for practical purposes, subject to the tolerances given.

PRESSURE RATINGS FOR SCREW THREADED ENDS FOR PLUMBING INSTALLATIONSThe nett wall thickness of a pipe determines the pressure rating. The wall thickness forfeited during threading must be taken into account. This is why the working pressure rating for medium and heavy pipes is considered to be the same.

PRESSURE RATING FOR HIGH PRESSURE INSTALLATIONSThe working pressure for plain ended pipes differs for medium and heavy pipes. The pressure rating for a screw threaded pipe is only considered the same as a plain ended pipe when a screwed on flange has been welded in place. The type of pipe joint will determine the strength, durability and life expectancy of a plain ended pipe system.

Nominalsize

Outside diameter mm

mm2.02.02.32.32.82.82.83.23.23.53.94.24.2

Mediumclass

Wall thickness

min2.52.52.82.83.53.53.53.93.94.24.74.74.7

Heavyclassmaxmin

13.917.421.727.234.242.948.860.876.689.5114.9140.6166.1

max0.590.76

1.1231.4422.2252.8433.2614.6065.8697.60410.92414.44717.148

Mediumclass

Approx. mass

kg/m0.7100.9201.3401.7282.7113.4814.0035.5987.1539.03313.02116.05819.072

Heavyclasskg/m

T R A D I N G8101520253240506580

100125150

Maximum working pressure rating (static)

Nominalsizemm

40404040404040202020202020

Screw threaded endsMedium and heavy

Plain end pipes

classes70707070707070606060505050

Medium class80808080808080707070606060

Heavy class

Maximum working pressure rating bar


T R A D I N G

Carbon Steel

Carbon Steel

Carbon Steel

Carbon Steel

Carbon Steel

Carbon Steel

Carbon Steel

Carbon Steel

Carbon Steel

Carbon Steel

Carbon Steel

Carbon Steel

Carbon Steel Class 60

Carbon Steel Class 70

Killed Carbon Steel

Killed Carbon Steel

Killed Carbon Steel

3.5% Nickel

3.5% Nickel

3.5% Nickel

Carbon-Mo

0.5% Mo

0.5% Mo

1% Cr

1% Cr

1% Cr

1.25% Cr

1.25% Cr

1.25% Cr

Cr Mo

2.25% Cr

K21590

4-6% Cr

K41545

K41545

K61595

7% Cr

7% Cr

9% Cr

9% Cr

9% Cr

0.5% Mo

0.5% Mo

0.5% Mo

0.5% Mo

0.5% Mo

0.5% Mo

1% Mo

0.5% Mo

0.5% Mo

1% Mo

1% Mo

1% Mo

Material

Metric conversions

10 000lb/in² = 68.95 MPa

100MPa = 14 500lb/in²

AP15L

AP15L

AP15L

AP15L

AP15L

A106

A234

A106

A234

A106

A234

A105

A181

A181

A350

A333

A420

A350

A333

A420

A182

A234

A335

A182

A234

A335

A182

A234

A335

A182

A234

A335

A182

A234

A335

A182

A234

A335

A182

A234

A335

API/ASTM Specifications

Chemical compositions % Stress (min)

0.21 max

0.26 max

0.28 max

0.30 max

0.26 max

0.25 max

0.25 max

0.30 max

0.30 max

0.35 max

0.35 max

0.35 max

0.35 max

0.35 max

0.30 max

0.30 max

0.30 max

0.20 max

0.30 max

0.30 max

0.28 max

0.28 max

0.10/0.20

0.10/0.20

0.20 max

0.15 max

0.10/0.20

0.20 max

0.15 max

0.15 max

0.15 max

0.15 max

0.15 max

0.15 max

0.15 max

0.15 max

0.15 max

0.15 max

0.15 max

0.15 max

0.15 max

Carbon

0.90 max

1.15 max

1.25 max

1.35 max

1.35 max

0.27/0.93

0.27/0.93

0.29/1.06

0.29/1.06

0.29/1.06

0.29/1.06

0.60/1.05

1.10 max

1.10 max

1.35 max

0.40/1.06

0.40/1.06

0.90 max

0.29/1.06

0.39/1.06

0.60/0.90

0.30/0.90

0.30/0.80

0.30/0.80

0.30/0.80

0.30/0.61

0.30/0.80

0.30/0.80

0.30/0.60

0.30/0.60

0.30/0.60

0.30/0.60

0.30/0.60

0.30/0.60

0.30/0.60

0.30/0.60

0.30/0.60

0.30/0.60

0.30/0.60

0.30/0.60

0.30/0.60

Mangan

0.040

0.040

0.040

0.040

0.040

0.048

0.048

0.048

0.050

0.048

0.050

0.040

0.050

0.050

0.035

0.050

0.050

0.035

0.025

0.030

0.045

0.045

0.045

0.040

0.045

0.045

0.040

0.040

0.030

0.040

0.040

0.030

0.030

0.040

0.030

0.030

0.030

0.030

0.030

0.030

0.030

PhosNo

A

B

X42

X52

X60

A

WPA

B

WPB

C

WPC

A/M

A/M

A/M

LF1

Gr1

LF3

Gr6

WPL6

F1

WP1

P1

F12

WP12

P12

F11

WP11

P11

F22

WP22

P22

F5

WP5

P5

F7

WP7

P7

F9

WP9

P9

Grade

Line Pipe

Line Pipe

Line Pipe

Line Pipe

Line Pipe

Pipe

Fittings

Pipe

Fittings

Pipe

Fittings

Flanges

Flanges

Flanges

Flanges

Pipe

Fittings

Flanges

Pipe

Fitting

Flanges

Fittings

Pipe

Flanges

Fittings

Pipe

Flanges

Fittings

Pipe

Flanges

Fittings

Pipe

Flanges

Fittings

Pipe

Flanges

Fittings

Pipe

Flanges

Fittings

Pipe

Form (max)

0.050

0.050

0.050

0.050

0.050

0.058

0.058

0.058

0.058

0.058

0.058

0.050

0.050

0.050

0.040

0.060

0.060

0.040

0.025

0.030

0.045

0.045

0.045

0.040

0.045

0.045

0.040

0.040

0.030

0.040

0.040

0.030

0.030

0.030

0.030

0.030

0.030

0.030

0.030

0.030

0.030

Sulph

0.10 min

0.10 min

0.10 min

0.10 min

0.10 min

0.10 min

0.35 max

0.35 max

0.35 max

0.20/0.35

0.10 min

0.10 min

0.10/0.50

0.10/0.50

0.10/0.50

0.10/0.60

0.60 max

0.50 max

0.50/1.00

0.50/1.00

0.50/1.00

0.50 max

0.50 max

0.50 max

0.50 max

0.50 max

0.50 max

0.50/1.00

0.50/1.00

0.50/1.00

0.50/1.00

0.25/1.00

0.25/1.00

Silicon

0.15

0.15

0.15

0.44/.065

0.44/0.65

0.44/0.65

0.44/0.65

0.44/0.65

0.44/0.65

0.44/0.65

0.44/0.65

0.44/0.65

0.87/1.13

0.87/1.13

0.87/1.13

0.44/0.65

0.44/0.65

0.45/1.65

0.44/0.65

0.44/0.65

0.44/0.65

0.90/1.10

0.90/1.10

0.90/1.10

Molyb

0.40

0.40

0.40

3.25/3.75

Nickel

0.40

0.40

0.40

0.80/1.25

0.80/1.25

0.80/1.25

1.00/1.50

1.00/1.50

1.00/1.50

2.00/2.50

1.90/2.60

1.90/2.60

4.00/6.00

4.00/6.00

4.00/6.00

6.00/8.00

6.00/8.00

6.00/8.00

8.00/10.00

8.00/10.00

8.00/10.00

Chrome(max)

331

413

413

455

517

330

330

415

415

485

485

485

415

485

415

380

380

485

415

415

485

380

380

485

485

415

485

485

415

515

515

415

485

415

415

485

415

415

585

415

415

TensileMPa

207

241

289

358

413

205

205

240

240

275

275

250

205

250

205

205

205

260

240

240

275

205

205

275

275

205

275

275

205

310

310

205

275

205

205

275

205

205

380

205

205

YieldMPa


PIPES - Carbon and Alloy Steel Pipe Materials

N G



PIPES - Dimensional tolerances for Steel Pipe to API specifications 5L and 5 XL

Up to 65mm

80mm

100mm & larger (seamless)

100mm up to 450mm

Over 500mm (welded)

+0.40-0.79mm

+-1%

+-0.75%

+-1%

+-1%

Nominal bore Outside diameter

+20%-12.5%

+18%-12.5%

+15%-12.5%

+15%-12.5%

+15%-10.0%

STD,XS,XXS,+10%-3.5%

Specialplainend+10%-5%

Wall thickness Theoreticalmass%

Minaverage5.40m

shortestpiece2.97m

Singlerandom

Minaverage11.55mshortest

piece4.62m

Doublerandom

Mass Lengths

T R A D I NN

A120

A53 GrA

A53 GrB

A106 GrA

A106 GrB

A106 GrC

A333 Gr1

A333 Gr6

A335 GrP1

A335 GrP12

A335 Grp11

A335 Grp22

A335 GrP5

A335 GrP7

A335 GrP9

1387

3601/22

3601/27

3602/23

3602/27

3602/35

3603/LT50

3603/410LT50

3604/240

3604/620

3604/621

3604/622

3604/625

3604/627

3604/629

ASTM BS

1629 St 00

1629 M St35.29

1629 M St45.29

17175 M St35.8

17175 M St45.8

17175 17 Mn4

TT St35N

17175 SEW 680

17175 16 Mo5

17175 13 CrMo44

17175 22 CrMo44

17175 10 CrMo910

17175 12 CrMo195

17175x12 CrMo7

17175x12 CrMo91

DIN

1.0350

1.0350

1.5423

1.7335

1.7350

1.7380

1.7362

1.7368

1.7386

WERKSTOFF

Pipe SpecificationsDimensions and tolerancesfor bevelled ends on pipesand fittingsASA B 37.5Bevel for wall thicknesses 4.8 up toand including 22.2

37.5° +- 2.5°

10° + 1°

30° + 5°

37.5° +- 2.5°1922.2

1.6 +- 0.8 root face



22.2max

3.2radiusmin

Bevel for wall thicknesses unless specified

API 5LBevel for wall thicknesses over 22.2

FITTINGS10E&OE

BUTTWELD I FORGED STEEL I MALLEABLE CAST I WROUGHT STEEL



T R A D I N G

15

20

25

32

40

50

65

80

90

100

125

150

200

250

300

350

400

450

500

600

Nominalpipesizemm

21.3

26.7

33.4

42.2

48.3

60.3

73.0

88.9

101.6

114.3

141.3

168.3

219.1

273.0

323.9

355.6

406.4

457.2

508.0

609.6

Outsidediameter

ODmm

38.1

28.6

38.1

47.6

57.2

76.2

95.3

114.3

133.4

152.4

190.5

228.6

304.8

381.0

457.2

533.4

609.6

685.8

762.0

914.4

Centreto end

Amm

15.80

20.93

26.64

35.05

40.89

52.50

62.71

77.93

90.12

102.26

128.19

154.05

202.72

254.51

304.80

336.55

387.35

438.15

488.95

590.55

Insidediameter

IDmm

2.77

2.87

3.38

3.56

3.68

3.91

5.16

5.49

5.74

6.02

6.55

7.11

8.18

9.27

9.53

9.53

9.53

9.53

9.53

9.53

Wallthickness

Tmm

Standard

0.10

0.10

0.20

0.30

0.40

0.70

1.30

2.00

2.80

3.80

6.50

10.10

20.30

36.00

53.00

68.00

89.20

113.00

140.00

202.00

Massapprox

kg13.87

18.85

24.31

32.46

38.10

49.25

59.00

73.66

85.45

97.18

122.25

146.33

193.68

242.87

288.90

317.50

363.52

409.55

455.63

547.67

Insidediameter

IDmm

3.73

3.91

4.55

4.85

5.08

5.54

7.01

7.62

8.08

8.56

9.53

10.97

12.70

15.09

17.48

19.05

21.44

23.83

26.19

30.96

Wallthickness

Tmm

Schedule 80

0.10

0.10

0.20

0.30

0.50

0.90

1.70

2.70

3.90

5.30

9.30

15.30

30.90

57.40

94.70

132.00

195.00

274.00

372.00

634.00

Massapprox

kg


BUTTWELD FITTINGS - ASTM A234 WPB 90° Elbows. Long radius to ANSI B 16.9

ID

OD

TA


T R A D I N G

15

20

25

32

40

50

65

80

90

100

125

150

200

250

300

350

400

450

500

600

Nominalpipesizemm

21.3

26.7

33.4

42.2

48.3

60.3

73.0

88.9

101.6

114.3

141.3

168.3

219.1

273.0

323.9

355.6

406.4

457.2

508.0

609.6

Outsidediameter

ODmm

15.9

11.11

22.2

25.4

28.6

34.9

44.5

50.8

57.2

63.5

79.4

95.3

127.0

158.8

190.5

222.3

254.0

285.8

317.5

381.0

Centreto end

Bmm

15.80

20.93

26.64

35.05

40.89

52.50

62.71

77.93

90.12

102.26

128.19

154.05

202.72

254.51

304.80

336.55

387.35

438.15

488.95

590.55

Insidediameter

IDmm

2.77

2.87

3.38

3.56

3.68

3.91

5.16

5.49

5.74

6.02

6.55

7.11

8.18

9.27

9.53

9.53

9.53

9.53

9.53

9.53

Wallthickness

Tmm

Standard

0.10

0.10

0.10

0.10

0.20

0.30

0.70

1.00

1.40

1.90

3.30

5.10

10.20

18.00

26.50

39.60

59.00

84.00

110.00

183.00

Massapprox

kg13.87

18.85

24.31

32.46

38.10

49.25

59.00

73.66

85.45

97.18

122.25

146.33

193.68

242.87

288.90

317.50

363.52

409.55

455.62

547.68

Insidediameter

IDmm

3.73

3.91

4.55

4.85

5.08

5.54

7.01

7.62

8.08

8.56

9.53

10.97

12.70

15.09

17.48

19.05

21.44

23.83

26.19

30.96

Wallthickness

Tmm

Schedule 80

0.15

0.15

0.15

0.20

0.24

0.50

0.90

1.40

2.00

2.67

4.62

7.07

15.40

28.70

47.40

66.00

97.50

137.00

186.00

317.00

Massapprox

kg


BUTTWELD FITTINGS - ASTM A234 WPB 45° Elbows. Long radius to ANSI B 16.9

OD

T

B

B ID


T R A D I N G

25

32

40

50

65

80

90

100

125

150

200

250

300

350

400

450

500

600

Nominalpipesizemm

33.4

42.2

48.3

60.3

73.0

88.9

101.6

114.3

141.3

168.3

219.1

273.1

323.9

355.6

406.4

457.2

508.0

609.6

Outsidediameter

ODmm

25.4

31.8

38.1

50.8

63.5

76.2

88.9

101.6

127.0

152.4

203.2

254.0

304.8

355.6

406.4

457.2

508.0

609.6

Centreto end

Amm

26.64

35.05

40.89

52.50

62.71

77.93

90.12

102.26

128.19

154.05

202.72

254.51

304.80

336.55

387.35

438.15

488.95

590.55

Insidediameter

IDmm

3.38

3.56

3.68

3.91

5.16

5.49

5.74

6.02

6.55

7.11

8.18

9.27

9.53

9.53

9.53

9.53

9.53

9.53

Wallthickness

Tmm

Standard

0.10

0.20

0.20

0.40

0.90

1.40

1.90

2.60

4.30

6.80

13.60

24.00

35.30

45.40

59.40

75.40

93.30

138.50

Massapprox

kg33.40

42.16

38.10

49.25

59.00

73.66

85.45

97.18

122.25

146.33

193.68

242.87

288.90

317.50

363.52

409.55

455.63

547.67

Insidediameter

IDmm

4.55

4.85

5.08

5.54

7.01

7.62

8.08

8.56

9.53

10.97

12.70

15.09

17.48

19.05

21.44

23.83

26.19

30.96

Wallthickness

Tmm

Schedule 80

0.10

0.20

0.30

0.60

1.10

1.80

2.60

3.60

6.20

10.20

20.60

38.20

63.20

88.20

130.00

183.00

248.00

440.00

Massapprox

kg


BUTTWELD FITTINGS - ASTM A234 WPB 90° Elbows. Short radius to ANSI B 16.28

ID

OD

TA

15

20

25

32

40

50

65

80

90

100

125

15108

20151025201510322520154032252015504032252065504032258065504032259080655040

1009080655040

12510090806550

Run mmNominal Pipe Size

Branch mm25.425.425.428.628.628.638.138.138.138.147.647.647.647.657.157.157.157.157.163.563.563.563.563.576.276.276.276.276.285.785.785.785.785.785.795.295.295.295.295.2

104.8104.8104.8104.8104.8104.8123.8123.8123.8123.8123.8123.8

25.425.425.428.628.628.638.138.138.138.147.647.647.647.657.157.157.157.157.163.560.353.950.844.476.269.966.763.557.185.782.576.273.069.866.795.292.088.982.579.4

104.8101.698.495.288.985.7

123.8117.5114.3111.1107.9104.8

Run A mmCentre to End

Branch B mm0.080.060.040.110.160.160.240.230.230.200.460.390.370.350.710.680.550.520.500.990.930.890.740.701.901.531.471.561.502.852.272.142.082.052.004.474.884.534.354.264.834.623.823.693.553.508.006.186.348.106.086.00

0.110.090.060.160.150.130.320.290.280.260.550.510.480.460.800.770.720.690.661.191.111.071.021.002.191.991.901.861.823.243.042.852.762.682.606.526.526.526.526.527.506.255.335.144.954.859.288.698.818.598.208.38

StandardMass approx kg

Schedule 80


0 23

0.46

0 37

0.74

1 901.53

0 28

0.55

0 48

1.02

2 191.9976.2 69.950

32

65 76 2 76 265

63.5 50.825

47 6 47 620

47.6 47.632

38 1 38 115

0.370.350.710.6800000.930.890 70.744

0.480.460.800 77

.7269.6619

1.111.071 01.022

47.647.657.157.157.157.157.163.563.563.56363.55

47.647.657.157.157.157.157.163.560.353.95050.88

201540322520

540322525

40

5 6

57777 57.1

5769

50

2201550 63.

5757

5

7.17

0.7700.6901.19

0.680000

0.680.550.520.500.99

0.39 0.5147.6 47.625

0 20.2330.200 46

0 20.2880.260 55

3838.1138.147 6

3838.1138.147 6

1515103232

1.901 53

2.191 99

76.276 2

76.269 9

6550

6500.700 1 01.0006363.5 4444.442020

N G2 272 27N G1.501.502.852.85N GN GR A D I N85 785 7 82 52 5T R656 R A D I N76.276.2

85.785.757.17.185.75.7R A D I NT R2525

808T RT R A D I NR N


BUTTWELD FITTINGS - ASTM A234 WPB Tees Equal and Unequal to ANSI B 16.9

B

A A


150

200

250

300

350

400

450

500

600

15012510090806550

2001501251009080

25020015012510090

300250200150125100350300250200150400350300250200150450400350300250200500450400350300250200600500450400350300250

Run mmNominal Pipe Size

Branch mm142.9142.9142.9142.9142.9142.9142.9177.8177.8177.8177.8177.8177.8215.9215.9215.9215.9215.9215.9254.0254.0254.0254.0254.0254.0279.4279.4279.4279.4279.4304.8304.8304.8304.8304.8304.8342.9342.9342.9342.9342.9342.9381.0381.0381.0381.0381.0381.0381.0431.8431.8431.8431.8431.8431.8431.8

142.9136.5130.2127.0123.8120.6117.5177.8168.3161.9155.6152.4152.4215.9203.3193.7190.5184.1177.8254.0241.3228.6219.1215.9209.5279.4269.9257.2247.6238.1304.8304.8295.3282.6273.0263.5342.9330.2330.2320.7308.0298.4381.0368.3355.6355.6346.1333.4323.8431.8431.8419.1406.4406.4396.9384.2

Run A mmCentre to End

Branch B mm10.209.228.818.938.528.458.37

22.9018.8018.4018.0017.9017.8536.6032.4030.5030.1029.9029.8558.4055.2053.1051.2050.0049.7583.2079.4076.1063.7061.5096.3089.5085.7082.4080.0077.50

131.00121.00118.00114.00110.00104.00173.00167.00162.00161.00158.00152.00145.00274.00263.00245.00235.00226.00218.00212.00

15.9014.0013.5013.1012.9012.7012.6029.0027.0026.2025.6025.0024.8560.8043.9042.0041.3040.0039.4095.8071.8062.9061.0059.5058.00

129.0089.5085.5078.3076.00

173.00108.00105.00101.0096.0090.00

253.00135.00133.00131.00128.00125.00353.00168.00163.00162.00160.00159.50158.60748.00606.00533.00490.00490.00452.00452.00

StandardMass approx kg

Schedule 80

18 80

18.00

17 85

51.20

49 7583.20

27 00

25.60

24 85

61.00

58 00129.00279.4 279.4350

254 0 209 5100

254.0 219.1150

177 8 152 480

177.8 155.6100

177 8 168 3150

350

17.8536.6032.4030.5030.1029.9029.8558.4055.2053.105151.2020

24.8560.8043.9042 00

1.300 009.405 80

71.8062.906161.0000

177.8215.9215.9215.9215.9215.9215.9254.0254.0254.0254254 0.0

152.4215.9203.3193.7190.5184.1177.8254.0241.3228.6219219 1.1

80250200150125

00

3250200150150

250

0 30 25

215515

90

99

93.79

00 00

300

11090

300 254

21515 9

12

93.790

42.004140.003995.80

30.5030292958

30.500.109.909.858.40

17.90 25.00177.8 152.490

1818.808018.4018 00

2727.000026.2025 60

177177 8.8177.8177 8

168168 3.3161.9155 6

150150125100

49.7583 20

58.00129 00

254.0279 4

209.5279 4

100350350

050.0000 959. 0502 4254 0.0 21215 9.912125

N G63.7063.7061.5061.5096 306 30N GN GR A D I N279.479.4

279.4279.4304 8304 8

247.647.238.138.304 804R A D I NR A D I NT R200200

15014004T RT RR N


BUTTWELD FITTINGS - ASTM A234 WPB Tees Equal and Unequal to ANSI B 16.9

B

A A


T R A D I N G

20 x 1525 x 1525 x 2032 x 1532 x 2032 x 2540 x 1540 x 2040 x 2540 x 3250 x 1550 x 2050 x 2550 x 3250 x 4065 x 2565 x 3265 x 4065 x 5080 x 2580 x 3280 x 4080 x 5080 x 65

100 x 25100 x 32100 x 40100 x 50100 x 65100 x 80125 x 50125 x 65125 x 80

125 x 100150 x 50150 x 65

Nominal PipeSize mm

26.7 x 21.333.4 x 21.333.4 x 26.742.2 x 21.342.2 x 26.742.2 x 33.448.3 x 21.348.3 x 26.748.3 x 33.448.3 x 33.460.3 x 21.360.3 x 26.760.3 x 33.460.3 x 42.260.3 x 48.373.0 x 33.473.0 x 42.273.0 x 48.873.0 x 60.388.9 x 33.488.9 x 42.288.9 x 48.388.9 x 60.388.9 x 73.0114.3 x 33.4114.3 x 42.2114.3 x 48.3114.3 x 60.3114.3 x 73.0114.3 x 88.9141.3 x 60.3141.3 x 73.0141.3 x 88.9141.3 x 114.3168.3 x 60.3168.3 x 73.0

Outside diametermm

38.150.850.850.850.850.863.563.563.563.572.272.272.272.272.288.988.988.988.988.988.988.988.988.9101.6101.6101.6101.6101.6101.6127.0127.0127.0127.0139.7139.7

Length Lmm

0.070.180.180.180.180.220.220.250.280.310.310.310.340.380.400.560.560.620.680.680.720.770.810.901.241.241.301.361.471.532.262.382.502.723.173.29

Standard0.100.200.200.220.220.220.300.310.340.350.400.450.500.520.540.800.840.860.901.021.081.131.181.241.591.701.811.921.982.042.943.173.403.744.304.53

Schedule 80Mass approx kg


BUTTWELD FITTINGS - ASTM A234 WPB Welding ReducersConcentric and Eccentric to ANSI B 16.9

L

OD OD


T R A D I N G

150 x 80150 x 90150 x 100150 x 125200 x 80200 x 90200 x 100200 x 125200 x 150*250 x 80250 x 100250 x 125250 x 150250 x 200*300 x 100300 x 125300 x 150300 x 200300 x 250350 x 150350 x 200350 x 250350 x 300400 x 200400 x 250400 x 300400 x 350450 x 300450 x 350450 x 400500 x 350500 x 400500 x 450600 x 400600 x 450600 x 500

Nominal PipeSize mm

168.3 x 88.9168.3 x 101.6168.3 x 114.3168.3 x 141.3219.1 x 88.9

219.1 x 101.6219.1 x 114.3219.1 x 141.3219.1 x 168.3273.0 x 88.9273.0 x 114.3273.0 x 141.3273.0 x 168.3273.0 x 219.1323.9 x 114.3323.9 x 141.3323.9 x 168.3323.9 x 219.1323.9 x 273.0355.6 x 168.3355.6 x 219.1355.6 x 273.0355.6 x 323.9406.4 x 219.1406.4 x 273.0406.4 x 323.9406.4 x 355.6457.2 x 323.9457.2 x 355.6457.2 x 406.4508.0 x 355.6508.0 x 406.4508.0 x 457.2609.6 x 406.4609.6 x 457.2609.6 x 508.0

Outside diametermm

139.7139.7139.7139.7152.4152.4152.4152.4152.4177.8177.8177.8177.8177.8203.2203.2203.2203.2203.2330.2330.2330.2330.2355.6355.6355.6355.6381.0381.0381.0508.0508.0508.0508.0508.0508.0

Length Lmm

3.633.743.743.855.005.005.005.446.018.169.079.529.759.9813.3813.6014.0614.5115.4226.3026.5326.8727.2131.1131.5231.7532.2037.6538.1038.5553.3356.2456.7065.7767.1368.04

Standard4.765.005.215.447.257.507.718.168.5010.4317.0017.0017.0017.0017.2317.7026.7626.7626.7635.4035.5635.9436.2840.1640.3740.8241.2751.2551.7152.1676.2076.6577.1186.1888.4590.72

Schedule 80Mass approx kg

* Concentric only


BUTTWELD FITTINGS - ASTM A234 WPB Welding ReducersConcentric and Eccentric to ANSI B 16.9

L

OD

OD



BUTTWELD FITTINGS - ASTM A234 WPB Welding Caps to ANSI B 16.9

T R A D I N G

25

32

40

50

65

80

90

100

125

150

200

250

300

350

400

450

500

600

Nominalpipesizemm

33.4

42.2

48.3

60.3

73.0

88.9

101.6

114.3

141.3

168.3

219.1

273.0

323.9

355.6

406.4

457.2

508.0

609.6

Outsidediameter

ODmm

38.1

38.1

38.1

38.1

38.1

50.8

63.5

63.5

76.2

88.9

101.6

127.0

152.4

165.1

177.8

203.2

228.6

266.7

LengthE

mm3.3

3.5

3.6

3.9

5.1

5.4

5.7

6.0

6.5

7.1

8.1

9.2

9.5

9.5

9.5

9.5

9.5

9.5

Wallthickness

mm

Standard

0.11

0.14

0.17

0.23

0.39

0.66

0.97

1.17

1.91

2.90

5.19

9.15

13.30

15.90

20.00

25.60

31.90

45.10

Massapprox

kg4.5

4.8

5.0

5.5

7.0

7.6

8.0

8.5

9.5

10.9

12.7

15.06

17.35

19.05

21.41

23.80

26.19

30.94

Wallthickness

mm

Schedule 80

0.14

0.19

0.23

0.33

0.53

0.92

1.36

1.67

2.78

4.47

8.05

16.30

26.80

34.50

47.70

67.70

91.30

155.00

Massapprox

kg

E

OD



FITTINGS - Japanese Industrial Standard JIS B 2311-09

FITTINGS - 90° Elbows. Long Radius to JIS B 2311-09 (SGP - All sizes are welded)

T R A D I N G

15

20

25

32

40

50

65

80

90

100

125

150

200

*200

250

*250

300

*300

350

400

450

500

600

Nominalpipesizemm

21.7

27.2

34.0

42.7

48.6

60.5

76.3

89.1

101.6

114.3

139.8

165.2

216.3

219.1

267.4

273.0

318.5

323.8

355.6

406.4

457.2

508.0

609.6

Outsidediameter

mm16.1

21.6

27.6

35.7

41.6

52.9

67.9

80.7

93.2

105.3

130.8

155.2

204.7

207.5

254.2

259.8

304.7

310.0

339.8

390.6

441.4

492.2

593.8

Insidediameter

mm2.8

2.8

3.2

3.5

3.5

3.8

4.2

4.2

4.2

4.5

4.5

5.0

5.8

5.8

6.6

6.6

6.9

6.9

7.9

7.9

7.9

7.9

7.9

Wallthickness

T38.1

38.1

38.1

47.6

57.2

76.2

95.3

114.3

133.4

152.4

190.5

228.6

304.8

304.8

381.0

381.0

457.2

457.2

533.4

609.6

685.8

762.0

914.4

Centreto End

A0.08

0.10

0.15

0.25

0.35

0.63

1.12

1.58

2.11

2.91

4.49

7.09

14.40

14.40

25.40

25.40

38.10

38.10

56.70

74.30

94.20

117.00

168.00

Massapprox

kg

* Dimensions to BS 1965

The Japanese Industrial Standard JIS B 2311-09 specifies steel butt-welding pipe fittings which are generally used for ordinary piping in JIS G3452, for steam, water, oil, gas, etc at relatively low pressures.

MATERIALS: The fittings to this standard are made from materials in accordance with JIS G3452.

PRESSURE RATINGS: The fittings are free from leakage at hydrostatic pressure up to a maximum of 2.5 MPa.

WELDING END PREPARATIONS: Bevel dimensions and tolerances confirm to those shown in the diagram.

30° + 5’0

2.1 +- 1.2mmHeight of root face

ID

OD

TA

GT R A D I N GG

15

20

25

32

40

50

65

80

90

100

125

150

200

*200

250

*250

300

*300

350

400

450

500

600

Nominalpipesizemm

21.7

27.2

34.0

42.7

48.6

60.5

76.3

89.1

101.6

114.3

139.8

165.2

216.3

219.1

267.4

273.0

318.5

323.8

355.6

406.4

457.2

508.0

609.6

Outsidediameter

mm16.1

21.6

27.6

35.7

41.6

52.9

67.9

80.7

93.2

105.3

130.8

155.2

204.7

207.5

254.2

259.8

304.7

310.0

339.8

390.6

441.4

492.2

593.8

Insidediameter

mm2.8

2.8

3.2

3.5

3.5

3.8

4.2

4.2

4.2

4.5

4.5

5.0

5.8

5.8

6.6

6.6

6.9

6.9

7.9

7.9

7.9

7.9

7.9

Wallthickness

T15.8

15.8

15.8

19.7

23.7

31.6

39.5

47.3

55.3

63.1

78.9

94.7

126.2

126.2

157.8

157.8

189.4

189.4

220.9

252.5

284.1

315.6

378.7

Centreto End

A0.04

0.05

0.07

0.13

0.18

0.32

0.56

0.79

1.06

1.46

2.25

3.54

7.20

7.20

12.70

12.70

19.00

19.00

28.40

37.10

47.10

58.30

84.00

Massapprox

kg



FITTINGS - 90° Elbows. Short Radius to JIS B 2311-09

FITTINGS - 45° Elbows. Long Radius to JIS B 2311-09 (SGP - All sizes are welded)

25

32

40

50

65

80

90

100

125

150

200

*200

250

*250

300

*300

350

400

Nominalpipesizemm

34.0

42.7

48.6

60.5

76.3

89.1

101.6

114.3

139.8

165.2

216.3

219.1

267.4

273.0

318.5

323.8

355.6

406.4

Outsidediameter

mm27.6

35.7

41.6

52.9

67.9

80.7

93.2

105.3

130.8

155.2

204.7

207.5

254.2

259.8

304.7

310.0

339.8

390.6

Insidediameter

mm3.2

3.5

3.5

3.8

4.2

4.2

4.2

4.5

4.5

5.0

5.8

5.8

6.6

6.6

6.9

6.9

7.9

7.9

Wallthickness

T25.4

31.8

38.1

50.8

63.5

76.2

88.9

101.6

127.0

152.4

203.2

203.2

254.0

254.0

304.8

304.8

355.6

406.4

Centreto End

A0.10

0.17

0.23

0.42

0.74

1.05

1.41

1.94

2.99

4.73

9.61

9.61

16.90

16.90

25.40

25.40

37.80

49.30

Massapprox

kg

ID

OD

TA

OD

T

B

B ID


D


FITTINGS - Welding Reducers. Concentric and Eccentric to JIS B 2311-09SGP - All sizes are welded

T R A

20 x 15

25 x 20

25 x 15

32 x 25

32 x 20

32 x 15

40 x 32

40 x 25

40 x 20

50 x 40

50 x 32

50 x 25

50 x 20

65 x 50

65 x 40

65 x 32

65 x 25

80 x 65

80 x 50

80 x 40

80x32

90 x 80

90 x 65

90 x 50

90 x 40

100 x 90

100 x 80

100 x 65

100 x 50

125 x 100

125 x 90

125 x 80

125 x 65

150x125

150 x 100

150 x 90

150 x 80

150 x 65

Nominalpipesizemm

27.2 x 21.7

34.0 x 27.2

34.0 x 21.7

42.7 x 34.0

42.7 x 27.2

42.7 x 21.7

48.6 x 42.7

48.6 x 34.0

48.6 x 27.2

60.5 x 48.6

60.5 x 42.7

60.5 x 34.0

60.5 x 27.2

76.3 x 60.5

76.3 x 48.6

76.3 x 42.7

76.3 x 34.0

89.1 x 76.3

89.1 x 60.5

89.1 x 48.6

89.1 x 42.7

101.6 x 89.1

101.6 x 76.3

101.6 x 60.5

101.6 x 48.6

114.3 x 101.6

114.3 x 89.1

114.3 x 76.3

114.3 x 60.5

139.8 x 114.3

139.8 x 101.6

139.8 x 89.1

139.8 x 76.3

165.2 x 139.8

165.2 x 114.3

165.2 x 101.6

165.2 x 89.1

165.2 x 76.3

Outsidediameter

mm38.1

50.8

50.8

50.8

50.8

50.8

63.5

63.5

63.5

76.2

76.2

76.2

76.2

88.9

88.9

88.9

88.9

88.9

88.9

88.9

88.9

101.6

101.6

101.6

101.6

101.6

101.6

101.6

101.6

127.0

127.0

127.0

127.0

139.7

139.7

139.7

139.7

139.7

Length

mm0.06

0.11

0.10

0.15

0.14

0.13

0.23

0.21

0.19

0.36

0.34

0.32

0.29

0.59

0.54

0.52

0.48

0.73

0.66

0.61

0.59

0.96

0.90

0.83

0.77

1.17

1.10

1.04

0.97

1.74

1.65

1.58

1.50

2.55

2.36

2.27

2.18

2.09

Mass

kg

I N G

200 x 150

200 x 125

200 x 100

200 x 90

250 x 200

250 x 150

250 x 125

300 x 250

300 x 200

300 x 150

300 x 125

350 x 300

350 x 250

350 x 200

400 x 350

400 x 300

400 x 250

450 x 400

450 x 350

450 x 300

500 x 450

500 x 400

500 x 350

600 x 450

600 x 500

Nominalpipesizemm

219.1 x 165.2

219.1 x 139.8

219.1 x 114.3

219.1 x 101.6

273.0 x 219.1

273.1 x 165.2

273.0 x 139.8

323.8 x 165.2

323.8 x 165.2

323.8 x 165.2

323.8 x 139.8

355.6 x 323.8

355.6 x 273.0

355.6 x 219.1

406.4 x 355.6

406.4 x 323.8

406.4 x 273.0

457.2 x 406.4

457.2 x 355.6

457.2 x 323.8

508.0 x 457.2

508.0 x 406.4

508.0 x 355.6

609.6 x 457.2

609.6 x 508.0

Outsidediameter

mm152.4

152.4

152.4

152.4

177.8

177.8

177.8

203.2

203.2

203.2

203.2

330.2

330.2

330.2

355.6

355.6

355.6

381.0

381.0

381.0

508.0

508.0

508.0

508.0

508.0

Length

mm4.17

3.87

3.67

3.57

6.87

6.32

6.06

9.97

9.29

8.69

8.39

21.20

19.70

18.30

20.90

19.80

18.20

26.30

24.50

23.30

40.00

37.60

35.30

53.00

55.00

Mass

kg

L

OD

OD

L

OD OD

15

20

25

32

40

50

65

80

90

100

125

150

200

250

300

350

400

450

500

Nominalpipesizemm

21.7

27.2

34.0

42.7

48.6

60.5

76.3

89.1

101.6

114.3

139.8

165.2

219.1

273.0

323.8

355.6

406.4

457.2

508.0

Outsidediameter

mm16.1

21.6

27.6

35.7

41.6

52.9

67.9

80.7

93.2

105.3

130.8

155.2

207.5

259.8

310.0

339.8

390.6

441.4

492.2

Insidediameter

mm2.8

2.8

3.2

3.5

3.5

3.8

4.2

4.2

4.2

4.5

4.5

5.0

5.8

6.6

6.9

7.9

7.9

7.9

7.9

Wallthickness

T25.4

28.6

38.1

47.6

57.2

63.5

76.2

85.7

95.3

104.8

123.8

142.9

177.8

215.9

254.0

279.4

304.8

342.9

381.0

Centreto End

A25.4

28.6

38.1

47.6

57.2

63.5

76.2

85.7

95.3

104.8

123.8

142.9

177.8

215.9

254.0

279.4

304.8

342.9

381.0

Centreto End

B0.09

0.13

0.24

0.44

0.57

0.85

1.42

1.87

2.37

3.13

4.53

6.84

12.80

21.80

32.00

44.70

55.20

70.00

86.60

Massapprox

kg


0

5

0

5

0

00

5.2 155.2 5.0 142.9 142.9 6.84

00 508 2.2 7. 381.0 381.0

342.9 39.424550 9

00 406.4 390.6 7.9 304 8 304.8

50 355.6 339.8 7.9 279.4 279.4

00 323.8 310.0 6.9 254.0 254.0 32.00

44.70

55.20

70.00

86.604

4

8.0

45

.9

7

304

3

3

304.8

0

0

55.20

4928.05

441457.2

390.406

7.9

7.9

7.

3

3

304.8

38

342.9

04.8

8

5.20

250 273.0 259.8 6.6 215.9 215.9 21.80

0 219.1 207.5 5.8 177.8 177.8 12.80

N G


FITTINGS - Tees. Equal to JIS B 2311-09

FITTINGS - Welding Caps to JIS 2311-09

SGP - All sizes are welded

T R A D I NN50

65

80

100

125

150

200

250

300

350

400

450

500

Nominalpipesizemm

60.5

76.3

89.1

114.3

139.8

165.2

219.1

273.0

323.8

355.6

406.4

457.2

508.0

Outsidediameter

mm52.9

67.9

80.7

105.3

130.8

155.2

207.5

259.8

310.0

339.8

390.6

441.4

492.2

Insidediameter

mm3.8

4.2

4.2

4.5

4.5

5.0

5.8

6.6

6.9

7.9

7.9

7.9

7.9

Wallthickness

T38.1

38.1

50.8

63.5

76.2

88.9

101.6

127.0

152.4

165.1

177.8

203.2

228.6

Length

E0.23

0.33

0.50

0.88

1.29

1.99

3.61

6.33

9.43

13.2

16.6

21.2

26.4

Massapprox

kg

B

A A

E

ODID


T R A D I N G


FITTINGS - Forged 90° Elbows. ANSI B 16.11 Threads to ANSI B 1.20.1

FITTINGS - Forged 45° Elbows. ANSI B 16.11 Threads to ANSI B 1.20.1

3000lb Series

3000lb Series

8

10

15

20

25

32

40

50

Nominalpipesizemm

24.6

28.6

33.3

38.1

44.5

50.8

60.3

63.5

A

mm25.4

33.3

38.1

46.0

55.6

62.6

75.4

84.1

B

mm0.14

0.27

0.40

0.63

1.10

1.22

2.35

3.30

Massapprox

kg8

10

15

20

25

32

40

50

Nominalpipesizemm

24.5

24.5

28.5

33.5

38.0

44.5

51.0

60.5

A

mm25.5

25.5

33.5

38.0

46.0

55.5

62.0

75.5

B

mm14.0

17.5

21.7

27.1

33.8

42.6

48.7

61.1

D

mm9.5

11.0

12.5

14.5

16.0

17.5

19.0

22.0

E

mm0.09

0.13

0.25

0.32

0.52

0.86

1.12

1.80

Massapprox

kg

Threaded Socket Weld

8

10

15

20

25

32

40

50

Nominalpipesizemm

25.5

38.0

38.0

46.0

55.5

62.0

75.5

84.0

B

mm19.0

25.5

25.5

28.5

33.5

35.0

43.0

43.5

C

mm0.14

0.25

0.32

0.51

0.85

1.00

1.85

3.00

Massapprox

kg8

10

15

20

25

32

40

50

Nominalpipesizemm

25.5

25.5

38.0

38.0

46.0

55.5

62.0

75.5

B

mm19.0

19.0

25.5

25.5

28.5

33.5

35.0

43.0

C

mm14.0

17.5

21.7

27.1

33.8

42.6

48.7

61.1

D

mm9.5

11.0

11.0

12.5

14.5

16.0

16.0

17.5

G

mm0.08

0.13

0.18

0.30

0.45

0.75

0.90

1.30

Massapprox

kg


B

AA E

B D

B BD

CGC


T R A D I N G


FITTINGS - Forged Tees. ANSI B 16.11 Threads to ANSI B 1.20.1

FITTINGS - Forged Unions. ANSI B 16.11 Threads to ANSI B 1.20.1

3000lb Series

3000lb Series

8

10

15

20

25

32

40

50

Nominalpipesizemm

24.5

28.5

33.5

38.0

44.5

51.0

60.5

63.5

A

mm25.5

33.5

38.0

46.0

55.5

62.0

75.5

84.0

B

mm0.20

0.38

0.56

0.84

1.36

1.65

3.10

3.18

Massapprox

kg8

10

15

20

25

32

40

50

Nominalpipesizemm

24.5

24.5

28.5

33.5

38.0

44.5

51.0

60.5

A

mm25.5

25.5

33.5

38.0

46.0

55.5

62.0

75.5

B

mm14.0

17.5

21.7

27.1

33.8

42.6

48.7

61.1

D

mm9.5

11.0

12.5

14.5

16.0

17.5

19.0

22.0

E

mm0.16

0.14

0.31

0.39

0.61

0.93

1.24

1.91

Massapprox

kg


8

10

15

20

25

32

40

50

Nominalpipesizemm

44.5

47.5

54.0

58.5

63.5

71.5

79.5

92.0

A

mm22.0

25.5

32.0

38.0

44.5

57.0

63.5

76.0

B

mm0.14

0.20

0.35

0.43

0.65

0.98

1.26

2.01

Massapprox

kg8

10

15

20

25

32

40

50

Nominalpipesizemm

44.5

47.5

54.0

58.5

63.5

71.5

79.5

92.0

A

mm22.0

25.5

32.0

38.0

44.5

57.0

63.5

76.0

B

mm14.0

17.5

21.7

27.1

33.8

42.6

48.7

61.1

D

mm9.5

11.0

12.5

14.5

16.0

17.5

19.0

22.0

E

mm0.26

0.34

0.39

0.48

0.66

1.15

1.42

2.45

Massapprox

kg


AA

B D

E

B

A

B B D

A

E


T R A D I N G


FITTINGS - Forged Couplings. ANSI B 16.11 Threads to ANSI B 1.20.1

FITTINGS - Forged Caps. ANSI B 16.11 Threads to ANSI B 1.20.1

3000lb Series

3000lb Series

8

10

15

20

25

32

40

50

Nominalpipesizemm

35.0

38.0

47.5

51.0

60.5

66.5

79.5

85.5

A

mm19.0

22.0

29.0

35.0

44.5

57.0

63.5

76.0

B

mm0.05

0.06

0.13

0.19

0.39

0.68

0.99

1.37

Massapprox

kg8

10

15

20

25

32

40

50

Nominalpipesizemm

25.5

28.5

35.0

38.0

44.5

47.5

51.0

63.5

A

mm22.0

25.5

31.5

38.0

44.5

57.0

63.5

76.0

B

mm14.0

17.5

21.7

27.1

33.8

42.6

48.7

61.1

D

mm9.5

11.0

12.5

14.5

16.0

17.5

19.0

22.0

E

mm0.01

0.06

0.13

0.19

0.26

0.48

0.57

0.92

Massapprox

kg


8

10

15

20

25

32

40

50

Nominalpipesizemm

25.5

25.5

32.0

36.5

41.5

44.5

44.5

47.5

A

mm19.0

22.0

29.0

35.0

44.5

57.0

63.5

76.0

B

mm0.04

0.05

0.11

0.18

0.33

0.60

0.70

1.06

Massapprox

kg8

10

15

20

25

32

40

50

Nominalpipesizemm

17.5

19.0

22.0

25.5

27.0

30.0

32.0

38.0

C

mm22.0

25.5

31.5

38.0

44.5

57.0

63.5

76.0

B

mm14.0

17.5

21.7

27.1

33.8

42.6

48.7

61.1

D

mm9.5

11.0

12.5

14.5

16.0

17.5

19.0

22.0

E

mm0.04

0.05

0.10

0.16

0.22

0.42

0.51

0.85

Massapprox

kg


A B D

EA

B

B B D

EC

D



FITTINGS - Forged Hexagonal Head Plugs ANSI B 16.11Threads to ANSI B 1.20.1

FITTINGS - A105 Forged Steel Fittings. Pressure/Temperature Ratings

6000lb Series

8

10

15

20

25

32

40

50

Nominalpipesizemm

11.0

13.0

14.0

16.0

19.0

21.0

21.0

22.0

A

mm6.5

8.0

8.0

10.0

10.0

14.0

16.0

18.0

B

mm16.0

18.0

22.0

27.0

36.0

46.0

50.0

65.0

D

mm0.03

0.05

0.07

0.18

0.25

0.45

0.60

1.16

Massapprox

kg

Threaded

T R A D I N G-29 to 38

66

93

121

149

177

204

232

260

288

316

343

371

399

427

454

482

510

538

Series

Temp °C

14.00

13.80

13.60

13.40

13.30

13.10

13.00

12.70

12.20

11.50

10.80

10.00

9.15

8.25

7.10

5.80

4.30

3.00

1.65

2000

21.00

20.35

20.10

20.05

19.90

19.70

19.40

19.05

18.25

17.20

16.20

15.05

13.70

12.40

10.70

8.75

6.50

4.50

2.50

3000

28.00

27.50

27.20

26.90

26.50

26.20

25.90

25.30

24.30

23.00

21.50

20.50

18.30

16.55

14.20

11.65

8.65

6.00

3.35

4000

42.00

41.50

40.70

40.50

39.90

39.40

38.80

38.00

36.50

34.50

32.30

30.50

27.50

24.90

21.30

17.50

13.00

9.00

5.00

6000

BA

C



FITTINGS - Malleable Fittings to EN 10242

A comprehensive range of high quality pipe fittings manufactured to EN 10242 specifica-tions and distributed by Macsteel Trading branches across Southern Africa. Malleable pipe fittings are manufactured in Blackheart Malleable Iron from the finest materials available and comply in all respects with the requirements of EN 10242 ‘Standard specification for Malleable Cast Iron Pipe Fittings’.

These pipe fittings have beaded outlets up to 50mm and banded outlets over 50mm in size giving added strength where it is most required and the neatness of form of this beaded and banded adds to the appearance of the pipe line.

Fittings are screwed with taper male and female threads and this method is now acknowledged as being the best means of producing a satisfactory joint on pipe installations. (It enables the user to make a sound joint without excessive force which can lead to distortion of the pipe or fitting).

Pipe fittings are individually pressure tested to 5 bar air underwater.

All galvanised fittings are hot dip galvanised according to the best galvanising methods.

Malleable pipe fittings are suitable for working under pressures of up to 25 bar at 120°C.

All threads comply with ISO 7-1 standards.

Taper Male/female threads

All threads within the pipe fittings are fully engaged ensuring perfect joints without packing: only a small amount of joint compound needs to be used.

Bends 90° Female Bends 90° Maleand Female

Bends 45° Maleand Female

Caps Backnuts

Elbows 90° Maleand Female

Elbows 90° Female Tees Abnormal Tees Reducing Tees

Reducing Bushes15 - 150mm

Reducing Elbows Reducing Sockets Sockets Paralleland Taper

Plugs Flush Plugs Solid

Unions Flat Unions Cone

Plugs HollowHex Nipples

Crosses

Holderbat


T R A D I N G


FITTINGS - EN 10241:2000

BS EN 10241:2000 is the official English language version of EN 10241:200, it supersedes BS 1740-1:1971 which is withdrawn. This standard specifies the requirements for threaded fittings of nominal sizes from DN6 to DN150, made out of welded or seamless steel tubes. It is applicable to those threaded steel pipe fittings that are used in the transportation and distribution of liquid or gas.

The fitting shall have a smooth surface consistent with the manufacturing process and be free from burrs; surface marks may be ground.

Material:

Chemical composition - the fitting shall be manufactured from steel having the chemical composition indicated in Tables 1 and 2.

Chemical composition of seamless steel Chemical composition of fabricated and tubularsTable 1

0.25

C max %

1.4

S max %

0.0045

S max %

0.0045

P max %

0.25

C max %

0.35

S max %

0.09

P max %

320

TensileStrength

min N/mm²

20

Elongation

min. %

Table 2

Table 3

320

Tensilestrength

min N/mm²

20

Yieldstrength

min N/mm²

20

Elongation

min %

Table 4Mechanical properties of seamless steel Mechanical properties of fabricated and tubulars

Mechanical properties - the fittings shall be manufactured from base material having the mechanical properties indicatedin Tables 3 and 4. These properties shall not be subject to verification on the fitting.

Threads - Internal threads shall be parallel and external threads shall be taper conforming to ISO 7-1, except for certain tubulars such as long screws, nipples, bends and spring bends.

Running nipples would have a parallel thread, whereas close to barrel nipples have a taper thread at both ends.

Taper Male/female threads - All threads within the pipe fittings are fully engaged ensuring perfect joints without packing: only a small amount of joint compound needs to be used.

Protection - Fittings shall be supplied black (uncoated) and shall be protected by a protective coating e.g. light oil.

Inspection documents - Fittings shall be delivered without an inspection document. At the request of the purchaser, the manufacturer shall provide a certificate of compliance in accordance with EN 10242 type 2.1.

FLANGES29E&OE

CARBON STEEL FLANGES A105 I STEEL PLATE FLANGES



T R A D I


FLANGES - Carbon Steel Flanges for Oil, Gas and Petrochemical to ANSI B 16.5A105 Normalised

Length through Hub YLength through Hub Y

152025324050658090

100125150

200250300350400450500600

Nominalboremm

21.427.034.142.948.460.373.088.9

101.6114.3141.3165.1168.3219.1273.1323.9355.6406.4457.2508.0609.6

PipeODA

88.998.4

107.9117.5127.0152.4177.8190.5215.9228.6254.0279.4279.4342.9406.4482.6533.4596.9635.0698.5812.8

Flangediameter

B34.942.950.863.573.092.1104.8127.0139.7157.2185.7215.9215.9269.9323.8381.0412.7469.9533.4584.2692.1

Raised facediameter

D11.112.714.315.917.519.022.223.823.823.823.825.425.428.630.231.734.936.539.742.947.6

Flangethickness

T47.652.455.657.161.963.569.869.871.476.288.988.988.9101.6101.6114.3127.0127.0139.7144.5152.4

Welding neck

15.915.917.520.622.225.428.630.231.733.336.539.739.744.449.255.657.163.568.373.082.5

Slip onscrewed

socket weld60.369.879.488.998.4120.6139.7152.4177.8190.5215.9241.3241.3298.4361.9431.8476.2539.7577.8635.0749.3

Bolt PCD

44444444888888

12121216162020

No.of

bolts15.915.915.915.915.919.019.019.019.019.022.222.222.222.225.425.428.628.631.731.734.9

Bolthole dia

d

Class 150 Flanges

Approximate Mass (kg)

N G152025324050658090100125150200250300350400450500600

Nominalboremm

0.790.861.091.411.812.834.425.225.447.489.5311.3419.0525.4038.1051.2663.5068.0481.65118.84

Weldingneck

0.450.680.951.131.362.223.824.084.995.946.128.1612.7017.2427.2235.3842.1852.6265.3291.63

Slip onscrewed

socket weld0.570.911.091.251.702.774.045.446.357.379.0712.7021.7731.7545.3658.9777.71102.51123.38203.21

Blind

Note:

The 1.6mm raised face is included in thickness T and length Y. For dimensional tolerances see page 33

CROSS SECTION

BA

BA

DPCD

DPCD

B

T

DPCD

Y

Y

T

T

d

d

d


Length through Hub Y

Note:

The 1.6mm raised face is included in thickness T and length Y. For cross section refer to page 32

racaised face is included in thickness T and length Y.e is ction refer to page 32

s pa

aef

lu akn nace is included in tfer to page

kness T and ngth

D I N



Length through Hub Y

152025324050658090

100125150

200250300350400450500600

Nominalboremm

21.427.034.142.948.460.373.088.9

101.6114.3141.3165.1168.3219.1273.1323.9355.6406.4457.2508.0609.6

PipeODA

95.2117.5123.8133.3155.6165.1190.5209.5228.6254.0279.4317.5317.5381.0444.5520.7584.2647.7711.2774.7914.4

Flangediameter

B34.942.950.863.573.092.1104.8127.0139.7157.2185.7215.9215.9269.9323.8381.0412.7469.9533.4584.2692.1

Raised facediameter

D14.315.917.519.020.622.225.428.630.231.734.936.536.541.347.650.854.057.160.363.569.8

Flangethickness

T52.457.161.965.168.369.876.279.481.085.798.498.498.4111.1117.5130.2142.9146.0158.7161.9168.3

Welding neck

22.225.427.027.030.233.338.142.944.447.650.852.452.461.966.773.076.282.588.995.2

106.4

Slip onscrewed

socket weld66.782.588.998.4114.3127.0149.2168.3184.1200.0234.9269.9269.9330.2387.3450.8514.3571.5628.6685.8812.8

Bolt PCD

44444888888

12121216162020242424

No.of

bolts15.919.019.019.019.019.022.222.222.222.222.222.222.225.428.631.731.734.934.934.941.3

Bolthole dia

d

Class 300 Flanges


N GN152025324050658090

100125150200250300350400450500600

Nominalboremm

0.911.591.862.723.744.656.448.5012.2517.2430.8434.0252.1690.36

101.60157.40209.11217.27312.98443.16

Weldingneck

0.821.471.702.183.363.975.496.809.93

15.4229.0334.0245.3679.8397.52117.93166.01215.46277.60370.13

Slip onscrewed

socket weld0.911.361.952.723.744.316.538.6213.1518.1430.8437.1963.05108.86133.81171.46239.01301.64387.82521.63

Blind

T R AInside diameter

250mm and under +0.8-0

Outside diameter 600mm and under +1.6-0

Spot facing ±1°Spot facing on back of flangeparallel to flange face within

300mm and over +1.6-0

Total depth450mm and smaller +3.2

-0.8

450mm and over +4.8-1.6

DrillingBolt circle

Bolt spacing

±1.6

Chamfer angle All sizes ±2.5°±0.8

Outside dia of hub300mm and smaller +2.4

-1.6

300mm and over ±3.2

Thickness450mm and under +3.2

-0

500mm and over +4.8-0

Dimensional tolerances of Class 150, 300 and 600 Flanges to ANSI 16.5 : 1968

T R A D I N


Note:

The 1.6mm raised face is included in thickness T and length Y. For dimensional tolerances see page 33

CROSS SECTION



152025324050658090

100125150

200250300350400450500600

Nominalboremm

21.427.034.142.948.460.373.088.9

101.6114.3141.3165.1168.3219.1273.1323.9355.6406.4457.2508.0609.6

PipeODA

95.2117.5123.8133.3155.6165.1190.5209.5228.6273.0330.2355.6355.6419.1508.0558.8603.2685.8742.9812.8939.8

Flangediameter

B34.942.950.863.573.092.1

104.8127.0139.7157.2185.7215.9215.9269.9323.8381.0412.7469.9533.4584.2692.1

Raised facediameter

D14.315.917.520.622.225.428.631.734.938.144.447.647.655.663.566.769.876.282.589

101.6

Flangethickness

T52.457.161.966.769.873.079.482.585.7

101.6114.3117.5117.5133.3152.4155.6165.1177.8184.1190.5203.2

Welding neck

22.225.427.028.631.736.541.346.049.254.060.366.766.776.285.792.193.7106.4117.5127.0139.7

Slip onscrewed

socket weld66.782.588.998.4114.3127.0149.2168.3184.1215.9266.7292.1292.1349.2431.8488.9527.0603.2654.0723.9838.2

Bolt PCD

44444888888

12121216202020202424

No.of

bolts15.919.019.019.019.019.022.222.225.425.428.628.628.631.734.934.938.141.344.444.450.8

Bolthole dia

d

Class 600 Flanges


N GN152025324050658090100125150200250300350400450500600

Nominalboremm

0.911.591.862.723.744.656.448.5012.2517.2430.8434.0252.1690.36

101.60157.40209.11217.27312.98443.16

Weldingneck

0.821.471.702.183.363.975.496.809.93

15.4229.0334.0245.3679.8397.52117.93166.01215.46277.60370.13

Slip onscrewed

socket weld0.911.361.952.723.744.316.538.6213.1518.1430.8437.1963.05108.86133.81171.46239.04301.64387.82521.63

BlindBA

BA

DPCD

DPCD

B

T

DPCD

Y

Y

T

T

d

d

d

T R A D I N G

15 mm Nominal Bore. Pipe OD 21,3mm. ID 23Specification

EN 1092-1EN 1092-1EN 1092-1EN 1092-1EN 1092-1SABS1123SABS1123SABS1123SABS1123SABS1123BS10BS10BS10ANSI B 16.5

Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D80959595958095959595

95,395,395,388,9

ID2323232323232323232323232323

Flanges Raised Face HolesFlat FaceThickness

b121414141410101014149,59,59,511,1

d³40454545454045454545

34,9

f2222222222

1,6

No44444444444444

d¹11141414141114141414

14,314,314,315,9

PCD

55656565655565656565

66,766,766,760,3

F/FMass

0,400,670,670,670,670,330,480,480,670,670,450,450,450,44

R/FMass

0,340,580,580,580,580,270,390,390,580,58

0,37



Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D90

10510510510590

105105105105

101,6101,6101,698,4

ID2929292929292929292929292929


b141616161610101014149,59,59,512,7

d³50585858585058585858

42,9

f2222222222

1,6

No44444444444444

d¹11141414141114141414

14,214,214,215,8

PCD

65757575756575757575737373

69,8

F/FMass

0,580,930,930,930,930,420,580,580,810,810,510,510,510,61

R/FMass

0,520,830,830,830,830,350,480,480,720,72

0,54



Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D100115115115115100115115115115

114,3114,3120,6107,9

ID3535353535353535353535353535


b141616161610101016169,59,59,514,3

d³60686868686068686868

50,8

f2222222222

1,6

No44444444444444

d¹11141414141114141414

14,314,317,515,9

PCD

75858585857585858585

82,682,687,379,4

F/FMass

0,721,111,111,111,110,510,690,691,111,110,640,640,710,83

R/FMass

0,641,001,001,001,000,430,580,581,001,00

0,74



Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D120140140140140120140140140140

120,6120,6133,3117,5

ID4444444444444444444444444444


b161818181810101018189,59,512,715,9

d³70787878787078787878

63

f2222222222

1,6

No44444444444444

d¹14181818181418181818

14,214,217,515,9

PCD

901001001001009010010010010087,387,398,488,9

F/FMass

1,151,811,811,811,810,721,011,011,811,810,690,691,141,06

R/FMass

1,031,651,651,651,650,600,840,841,651,65

0,97



Table

6/310/316/325/340/3600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D130150150150150130150150150150

133,4133,4139,7127

ID5050505050505050505050505050


b161818181810101020209,59,512,717,5

d³80888888888088888888

73

f3333333333

1,6

No44444444444444

d¹14181818181418181818

14,214,217,515,9

PCD

10011011011011010011011011011098,498,4104,898,4

F/FMass

1,342,072,072,072,070,841,151,152,302,300,850,851,241,36

R/FMass

1,151,801,801,801,800,640,880,882,032,03

1,25



Table

6/310/316/325/340/3600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D140165165165165140165165165165

152,4152,4165,1152,4

ID6262626262626262626262626262


b162020202010101220209,59,515,919

d³9010210210210290102102102102

92

f3333333333

1,6

No44444444444444

d¹14181818181418181818

17,517,517,519

PCD

110125125125125110125125125125

114,3114,3127

120,6

F/FMass

1,482,722,722,722,720,921,361,632,722,721,061,062,172,10

R/FMass

1,262,412,412,412,410,711,051,322,412,41

1,95

65 mm Nominal Bore. Pipe OD 76,1 or 73,0mm ID 75 or 78Specification


Table

6/310/316/325/340/3600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D160185185185185160185185185185

165,1165,1184,1177,8

ID7575757575757575757575757575


b162020222210121222229,510,315,922,2

d³110122122122122110122122122122

104,8

f3333333333

1,6

No44488444884484

d¹14181818181418181818

17,517,517,519

PCD

130145145145145130145145145145127127146

139,7

F/FMass

1,923,243,403,563,561,202,042,043,563,561,211,312,563,40

R/FMass

1,672,883,043,213,210,951,681,683,213,21

3,19



Table

6/310/316/325/340/3600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D190200200200200190200200200200

184,1184,1203,2190,5

ID9191919191919191919191919191


b182020242410121422229,511,115,923,8

d³128138138138138128138138138138

127

f3333333333

1,6

No48888488884484

d¹18181818181818181818

17,517,517,519

PCD

150160160160160150160160160160146146

165,1152,4

F/FMass

2,963,613,614,334,331,642,172,533,973,971,441,683,013,92

R/FMass

2,603,223,223,953,951,281,782,143,583,58

3,72


Diagram: see page 36


FLANGES - Mild Steel FlangesEN BS EN 1092-1 : 2007 I SANS 1123 : 2007 I BS 10 : 1962


T R A D I N G



Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D210220220235235210220220235235

215,9215,9228,6228,6

ID116116116116116116116116116116116116116116


b182222262610121425259,512,719

23,8

d³148158158162162148158158162162

157,2

f3333333333

1,6

No48888488884888

d¹18181822221818182222

17,517,517,519

PCD

170180180190190170180180190190

177,8177,8190,5190,5

F/FMass

3,254,384,386,076,071,812,392,795,845,841,872,404,255,27

R/FMass

2,843,953,955,535,531,401,962,365,305,30

4,99

125 mm Nominal Bore. Pipe OD 139,7mm. ID 141 or 144Specification


Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D240250250270270240250250270270254254

279,4254

ID141141141141141141141141141141141141141141


b20222228281214162828

12,714,322

23,8

d³178188188188188178188188188188

185,7

f3333333333

1,6

No88888888888888

d¹18181826261818182626

17,517,522,222,2

PCD

200210210220220200210210220220

209,6209,6234,9215,9

F/FMass

4,335,425,428,218,212,603,453,948,218,213,303,727,355,97

R/FMass

3,854,924,927,527,522,122,953,447,527,52

5,67

150 mm Nominal Bore. Pipe OD 168,3mm. ID 168 or 171Specification


Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D265285285300300265285285300300

279,4279,4304,8279,4

ID168168168168168168168168168168168168168168


b20242430301216183030

12,717,522,225,4

d³202212212218218202212212218218

215,9

f3333333333

1,6

No888888888888128

d¹18222226261822222626

17,522,222,222,2

PCD

225240240250250225240240250250235235

260,4241,3

F/FMass

4,867,267,26

10,4210,422,914,845,45

10,4210,423,714,958,047,18

R/FMass

4,316,596,599,639,632,374,174,789,639,63

6,87



Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D320340340360375320340340360375

336,6336,6368,3342,9

ID221221221221221221221221221221221221221221


b22242632361418222832

12,719

25,428,6

d³258268268278285258268268278285

269,9

f3333333333

1,6

No881212128812121288128

d¹18222226301822222626

17,522,222,222,2

PCD

280295295310320280295295310320

292,1292,1323,9298,4

F/FMass

6,919,309,76

14,3217,964,406,978,26

12,5316,494,857,08

12,6611,42

R/FMass

6,248,498,9513,3516,863,736,167,4511,5615,40

10,97

250 mm Nominal Bore. Pipe OD 273mm. ID 276Specification


Table

6/3

10/316/325/340/3600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D375395405425450375395405425450

406,4406,4431,8406,4

ID276276276276276276276276276276276276276276


b24262935421620253038

15,922,228,630,2

d³312320320335345312320320335345

323,8

f3333333333

1,6

No121212121212121212128121212

d¹18222630331822262633

22,222,225,425,4

PCD

335350355370385335350355370385

355,6355,6381,1361,9

F/FMass

8,9511,8614,2420,1929,305,979,12

12,2817,8026,518,3311,3618,0615,11

R/FMass

8,1510,8713,1118,9327,765,178,1311,1416,5424,97

14,52



Table

6/3

10/316/325/340/3600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D440445460485515440445460485515

457,2457,2489

482,6

ID327327327327327327327327327327327327327327


b2426323852202228324019

25,431,831,7

d³365370378395410365370378395410

381,1

f4444444444

1,6

No1212121616121212161612121612

d¹22222630332222262633

22,225,425,425,4

PCD

395400410430450395400410430450

406,4406,4438,2431,8

F/FMass

11,9513,6619,0326,6645,1210,2011,5616,6523,1634,7111,2615,0523,8723,09

R/FMass

10,4712,1517,3424,7142,738,71

10,0514,9621,2132,32

22,22



Table

6/3

10/316/325/340/3600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D490505520555580490505520555580

527,1527,1552,5533,4

ID359359359359359359359359359359359359359359


b26303542582225303545

22,228,634,934,9

d³415430438450465415430438450465

412,8

f4444444444

1,6

No1216161616121616161612121612

d¹22222633362222263333

25,425,428,628,6

PCD

445460470490510445460470490510

469,9469,9495,3476,2

F/FMass

16,8821,8828,1841,8466,7314,2918,2324,1534,8752,6919,3124,8835,1031,35

R/FMass

15,2120,1526,2439,2463,7712,6116,5122,2232,2749,73

30,22



Table

6/3

10/316/325/340/3600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D540565580620660540565580620660

577,9577,9609,6596,9

ID411411411411411411411411411411411411411411


b28323848652225354050

22,231,841,436,5

d³465482490505535465482490505535

470

f4444444444

1,6

No1616161616161616161612122016

d¹22263036392226263339

25,425,428,628,6

PCD

495515525550585495515525550585

520,7520,7552,5539,7

F/FMass

20,1127,8236,2258,0797,6916,0621,7334,1349,2075,1521,7431,1347,9439,55

R/FMass

18,2525,6833,8454,8894,0114,2019,5931,7646,0271,46

38,22


EN BS EN 1092-1 : 2007 I SANS 1123 : 2007 I BS 10 : 1962D

OD

d2PCD

d1

fb Dimension b includes f


T R A D I N G



Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D595615640670685595615640670685

641,4641,4673,1635

ID462462462462462462462462462462462462462462


b30364254d2530404560

25,434,944,539,7

d³520532550555560520532550555575

533,4

f4444444444

1,6

No1620202020162020202012162016

d¹22263036392226263339

25,425,431,831,7

PCD

550565585600610550565585600610

584,2584,2609,6577,8

F/FMass

24,8933,9546,5770,31

20,7428,2945,4559,7483,9730,0540,7360,6442,93

R/FMass

22,8331,6143,9366,84

18,6825,9542,8256,2780,56

41,76



Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D645670715730755645670715730755

704,9704,9736,6698,5

ID513513513513513513513513513513513513513513


b30384658d2532405070

28,638,150,842,9

d³570585610615615570585610615615

584,2

f4444444444

1,6

No2020202020202020202016162420

d¹22263336422226333339

25,425,431,731,7

PCD

600620650660670600620650660670

641,4641,4673,1635

F/FMass

26,8440,7964,7087,84

22,3634,3556,2677,00120,0839,7252,9180,5354,62

R/FMass

24,5938,1661,2784,03

20,1231,7252,8373,19115,35

53,17



Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D755780840845890755780840845

825,5825,5850,9812,8

ID616616616616616616616616616

616616616616


b32425568d30385060

31,847,657,247,6

d³670685725720735670685725720

692,2

f555555555

1,6

No202020202020202020

16162420

d¹263036394826263339

28,631,835

34,9

PCD

705725770770795705725770770

755,7755,7781,1749,3

F/FMass

35,6355,5396,87124,78

33,4051,2994,88113,77

57,3184,88112,3576,39

R/FMass

31,9051,2491,32118,75

29,6747,0089,33107,75

74,60



Table

6/3

10/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D860895910960

860895910

908,1908,1

ID714714714714

714714714

714714


b40506385

354555

34,950,8

d³775800795820

775800795

f5555

555

No24242424

242424

2020

d¹26303642

262633

28,631,8

PCD

810840840875

810840840

844,6844,6

F/FMass

44,1375,87101,65165,55

46,0576,2398,98

64,1792,22

R/FMass

39,8570,9195,61157,87

41,7771,2792,95

64,1792,22



Table

6/310/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D975

101510251085

97510151025

ID816816816816

816816816


b44567495

385065

d³880905900930

880905900

f5555

555

No24242424

242424

d¹30333948

263339

PCD

920950950990

920950950

F/FMass

60,80107,70135,05225,94

62,86104,17139,44

R/FMass

55,38101,19127,64216,32

57,4397,67132,03



Table

6/310/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D1075111511251185

107511151125

1174,71174,7

ID918918918918

918918918

918918


b486282d

405570

47,663,5

d³980

100510001030

98010051000

f5555

555

No24282828

242828

2424

d¹30333948

263339

3535

PCD

1020105010501090

102010501050

1092,21092,2

F/FMass

74,57126,51166,05

73,10125,36163,99

148,89198,63

R/FMass

68,55125,83157,87

67,09118,17155,81



Table

6/310/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D1175123012551320

117512301255

1257,31257,3

ID1020102010201020

102010201020

10201020


b527090d

456075

50,866,7

d³1080111011151140

108011101115

f5555

555

No28282828

282828

2424

d¹30364256

263339

3538,1

PCD

1120116011701210

112011601170

1174,71174,7

F/FMass

88,33164,81229,49

89,06163,36227,32

159,90207,72

R/FMass

81,73156,16219,27

82,46154,71217,10



Table

6/310/316/325/340/3

600/31000/31600/32500/34000/3

D/3E/3F/3

ASA150/3

D140514551485

140514551485

1492,21492,2

ID122512251225

122512251225

12251225


b6083d

557085

60,379,4

d³129513301330

129513301330

f555

555

No323232

323232

3232

d¹333948

333945

3538

PCD

134013801390

134013801390

1409,71409,7

F/FMass

150,42256,09

148,58244,80334,99

255,12332,50

R/FMass

141,27245,37

139,43234,08321,55

EN BS EN 1092-1 : 2007 I SANS 1123 : 2007 I BS 10 : 1962


DOD

d2PCD

d1

fb Dimension b includes f

d - to be specified by the purchaser


36E&OE

STAINLESS STEEL CATALOGUE

T R A D I N G

T R A D I N G

The Macsteel Range of Stainless Steel Pipes, Fittings and Flanges

T R A D



PIPING

Standards: ASTM/ASME A/SA 312 TP 304 / 304L and 316 / 316LSizes: 15NB to 300NBWall Thickness: Sch10s and Sch40sRange: Welded, SeamlessSpecial: Pipe larger than 300NB is fabricated to A358 at requested wall thicknesses

THREADED FITTINGS

Standards: ANSI B 16.3Sizes: 15NB to 80NBRating: 150lb BSPRange: Elbows, Equal tees, Plugs, Sockets, Reducing bushes, Barrel nipples (all available only in 316)

FLANGES

Standards: ASTM/ASME A/SA 240 and A/SA 182Sizes: 15NB to 300NBRating: ANSI B 16.5 150lb, 300lb,600lb SABS 1123 T600, T1000, T1600, T2500 and T4000 BS10 Table D, E, F EN1092-1, PN10, PN16Products: Standard flanges including: slip-on, Weldnecks, BlindsSpecials: Non-standard flanges and flanges in other grades of stainless steel can be manufactured

ELBOWS, TEES, END CAPS AND REDUCERS

Standards: ASTM, ASME A/SA 403WP 304 / 304L 316 / 316L W, WX and WPS B 16.9Sizes: From 15NB to 300NBWall Thickness: Sch10s and Sch40sRange: 90° elbows, 45° elbows, Equal tees, Reducing tees, Concentric reducers, Eccentric reducers, End capsSpecials: Fittings larger than 300NB manufactured on request to ASTM/ASME A/SA 403 and ASTM A774

PIPE - ANSI B 36.19 and B 36.10 Seamless and Welded



T R A D I N G

Dimension and Weights for Austenitic Stainless Steel Pipe ANSI B 36.19 and ANSI B 36.10

in

1/8

1/4

3/8

1/2

3/4

1

1 1/4

1 1/2

2

2 1/2

3

3 1/2

4

5

6

8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

mm

10.29

13.72

17.15

21.34

26.67

33.40

42.16

48.26

60.33

73.03

88.90

101.60

114.30

141.30

168.28

219.08

273.05

323.85

355.60

406.40

457.20

508.00

558.80

609.60

660.40

711.60

762.00

812.80

863.60

914.40

kg/m

0.81

1.03

1.31

1.67

1.93

2.42

3.75

4.59

5.27

5.95

9.64

11.51

15.05

23.03

31.81

34.99

42.35

47.70

60.32

65.25

84.10

120.59

mm

1.24

1.65

1.65

2.11

2.11

2.77

2.77

2.77

2.77

3.05

3.05

3.05

3.05

3.40

3.40

3.76

4.19

4.57

4.78

4.78

4.78

5.53

5.54

6.35

7.92

kg/m

0.28

0.50

0.64

1.02

1.30

2.13

2.73

3.16

3.99

5.35

6.56

7.53

8.50

11.74

14.04

20.33

28.29

36.63

42.10

48.22

54.30

69.77

75.53

96.22

147.45

mm

1.73

2.24

2.31

2.77

2.87

3.38

3.56

3.68

3.91

5.16

5.49

5.74

6.02

6.55

7.11

8.18

9.27

9.52

kg/m

0.37

0.65

0.86

1.26

1.68

2.50

3.38

4.05

5.43

8.62

11.28

13.56

16.06

21.76

28.23

42.49

60.24

73.76

mm

2.41

3.02

3.20

3.73

3.91

4.55

4.85

5.08

5.54

7.01

7.62

8.08

8.56

9.52

10.97

12.70

12.70

12.70

kg/m

0.48

0.81

1.12

1.62

2.19

3.23

4.46

5.40

7.47

11.40

15.25

18.62

22.29

30.92

42.52

64.57

81.46

97.36

mm

6.35

6.35

6.35

6.35

6.35

6.35

7.92

7.92

7.92

7.92

7.92

7.92

kg/m

54.63

62.58

70.50

78.47

86.42

96.22

127.58

137.52

147.45

157.39

167.32

177.26

mm

6.35

6.35

6.35

7.92

7.92

7.92

9.52

9.52

9.52

12.7

12.7

12.7

12.7

12.7

12.7

kg/m

33.28

41.70

49.68

67.98

77.90

87.80

116.97

128.89

140.80

202.65

218.54

234.44

250.33

266.22

282.12

mm

7.04

7.80

8.38

9.52

9.52

11.13

12.70

12.70

14.70

15.88

15.88

15.88

15.88

15.88

kg/m

36.80

51.00

65.14

81.21

93.13

122.12

155.00

170.86

209.54

271.94

291.81

311.67

331.54

351.41

mm

1.73

2.24

2.31

2.77

2.87

3.38

3.56

3.68

3.91

5.16

5.49

5.74

6.02

6.55

7.11

8.18

9.27

9.52

9.52

9.52

9.52

9.52

9.52

9.52

9.52

9.52

9.52

9.52

9.52

9.52

kg/m

0.37

0.64

0.86

1.26

1.68

2.50

3.38

4.05

5.43

8.62

11.28

13.56

16.06

21.76

28.23

42.49

60.24

73.76

81.21

93.13

105.05

116.97

128.89

140.81

152.73

164.65

176.57

188.50

200.42

212.34

ANSI B 36.19

mm

1.65

1.65

1.65

1.65

1.65

1.65

2.11

2.11

2.11

2.11

2.77

2.77

2.77

3.40

3.96

3.96

4.19

4.19

4.77

4.78

5.54

6.35

Sch5SWall thickness and weight

ANSI B 36.10Wall thickness and weightNB OD

Sch10S Sch40S Sch80S Sch10 Sch20 Sch30 Standard

Standard ASTM / ANSI Specifications



T R A D I N G

ASTM A312 Stainless Steel Pipe

Specification: ASTM A312 seamless and welded austenitic stainless steel pipe.

Stipulation: This specification covers seamless and longitudinally welded austenitic steel pipe intended for high-temperature and general corrosive service.

Note: When the impact test criterion for a low-temperature sevice would be 20J energy absorption of 0.38mm lateral expansion, some of the austenitic stainless steel grades covered in this specification are accepted by certain pressure vessel or piping codes without the necessity of conducting the actual test.

Examples: Grades 304, 304L and 347 are accepted by the ASME Pressure Vessel Code Section VIII Division I by the Chemical Plant and Refinery Piping Code. ANSI B 31.3 for service at temperatures as low as -250°C without qualification by impact tests. Other AISI stainless steel grades are usually accepted for service temperatures as low as -200°C without impact testing.

Testing: Impact testing may, under certain circumstances, be required. For example, materials with chromium or nickel content outside the AISI range and carbon content exceeding 0.10% are required to be impact tested under the rules of ASME Section VIII Division I only when service temperatures are lower than -45°C.

Grades: Grades TP 304H, TP 304N, TP 316H, TP 316N, TP 321H, TP 347H and TP 348H are modifications of Grades TP 304, TP 316, TP 321, TP 347 and TP 348. These grades are intended for high temperature service.

Additions: Optional supplementary requirements are provided for pipes where a greater degree of testing is desired. These supplementary requirements call for additional tests to be made and when desired, one or more of these may be specified in the order.

ASTM A358 Steel Alloy Pipe for High Temperature Service

Specification: ASTM A358 steel alloy pipe for high temperature service.

Stipulation: ASTM A358 covers electric fusion welded austenitic chromium-nickel alloy steel pipe suitable for corrosive or high temperature service.

Note: Although no restrictions are placed on the sizes of the pipe furnished under this specification, commercial practice commonly limits sizes not less than NPS 8. The dimensionless designator NPS (nominal pipe size) has been substituted for such traditional terms as ‘nominal diameter’, ‘size’, and ‘nominal size’.

Range: This specification covers 19 grades of alloy steel. The selection of the proper alloy and requirements for heat treatment should be at the discretion of the purchaser, dependent on the service conditions to be encountered.

Classes: Five classes of pipe are covered as follows: Class 1: Pipe shall be double welded by processes employing filler metal in all passes and shall be completely radiographed. Class 2: Pipe shall be double welded by processes employing filler metal in all passes. No radiography is required. Class 3: Pipe shall be single welded by processes employing filler material in all passes and shall be completely radiographed. Class 4: Same as Class 3 except that the weld pass exposed to the inside pipe surface may be made without the addition of filler metal. Class 5: Pipe shall be double welded by processes employing filler metal in all passes and shall be spot radiographed.

Additions: Supplementary requirements, covering provisions ranging from additional testing to formalised procedures for manufacturing practices, are provided.

Standard ASTM / ANSI Specifications



T R A D I N G

ASTM A403 Buttweld Fittings

Specification: Wrought austenitic stainless steel pipe fittings.

Stipulation: This specification covers classes WP and CR. Class WP fittings are manufactured to the requirements of ANSI B 16.9, 16.11 or 16.28. They shall be capable of withstanding a test pressure prescribed in the specifications for the pipe with which the fitting is recommended to be used. Class CR fittings are manufactured according to MSS SP-43 and shall be capable of withstanding a test pressure based on the ratings in MSS SP-43. Tees fabricated using intersection welds shall be capable of passing a hydrostatic test based on 70% of the ratings in MSS SP-43. Fittings may be manufactured from blooms, billets, slabs, forging, bars, plates, seamless or welded pipe. Fittings shall be heat treated before machining. Fittings ordered as Class WP-S shall be of seamless construction. On fittings conforming to class WP-W, all welds made by the fitting manufacturer must be radiographed. Radiography is not required, however, if the fittings are made of welded pipe produced without the addition of filler material.

Note: In practice, fittings stocked under the designation ASTM A403 WP-W are spot-checked by means of radiography. The quality of the welds is guaranteed to meet the requirements in ASTM A403. Extra radiography can be performed at the customer’s request and cost. Class WP-WX fittings shall have all welds radiographed either prior to or after forming, whether the welds are made by the fitting manufacturer or the fittings are manufactured from welded pipes with or without the addition of filler metal. Fittings according to class CR do not require radiography. Hydrostatic testing is not required.

Additions: Each fitting shall be marked with the manufacturer’s name or trademark, the schedule number or pressure rating, steel grade, class and size. A certificate of compliance to the specification shall be the basis for approval.

ASTM A182 Pipe Flanges, Forged Fittings, Valves

Specification: ASTM A182 forged and rolled alloy-steel pipe flanges, forged fittings and valves, and parts for high temperature service.

Stipulation: This specification covers forged flanges manufactured according to dimensional standard ANSI B 16.5 as well as forged socket weld and threaded fittings manufactured to dimensional standard ANSI B 16.11.

Note: The material shall be forged as close as practicable to the specified shape and size. Forged and roller bar may be used for small cylindrically shaped parts. All austenitic forgings shall be furnished in heat treated condition. The heat treatment may be performed before machining.

Additions: Identification marks consisting of the manufacturer’s symbol and name, designation of service rating, specification number, steel grade and size shall be stamped on each forging. The marking confirms that the forging has been delivered in accordance with the specification.

For materials and testing information the ANSI standards contain references to specifications laid down by the American Society for Testing and Materials (ASTM) as listed on these pages.

304 / 304L Stainless Steel Data In-Depth



T R A D I N G

304 is used in all industrial, commercial and domestic fields because of its good corrosion resistance, mechanical properties, weldability and chemical composition.Applications: Tanks and containers for a large variety of liquids and solids. Process equipment in: mining, chemical, cryogenic, food, dairy and pharmaceutical industries.Fabrication: Easy to work S304 responds well to hardening by cold working. Typical operations include: bending, forming, deep drawing and upsetting.Specify: 304L, the low carbon variety for intergranular corrosion in the heat-affected zone.

Chemical Composition (ASTM A240)

304

304L

2. Properties at elevated temperatures

The values given refer to 304. Values for 304L are not given because strength values fall rapidly above 425°C.

The properties quoted in this publication are typical of mill productsand unless indicated should not be regarded as guaranteed minimumvalues for specification purposes.

Short time elevated temperature tensile strength

4. Corrosion Resistance - Aqueous

Atmospheric

For specific conditions, consult Macsteel Trading. As a roughguide, the examples are given for certain pure acid-water mixtures

C0.08 max0.03 max

Mn2.0

max

P0.045

max

S0.03

max

Si1.0

maxTemperature °C 20°C

Concentration(% by mass)Sulphuric acidNitric acidPhosphoric acidFormic acid

Environment

RuralMarineMarine-industrial

3040.00250.00760.0076

Corrosion rate (um/year)Aluminium-3S

0.0250.4320.686

Mild Steel5.834.046.2

10

2000

20

2000

40

2000

60

2000

80

1200

100

0020

TypTensile Strength

Proof Stress (0.2% offset)

Elongation (%in 50mm)

Hardness (Brinell)

Endurance (fatigue) limit

MPa

MPa

MPa

600

310

60

170

240

Min304 304L

515

205

40

Typ590

310

60

170

240

Min485

170

40

TemperatureTensile Strength

°CMPa

600380

700270

800170

3. Properties at subzero temperature 304 / 304L

TemperatureProof Stress(0.2% offset)Tensile StrengthImpact Str (Charpy V)

°CMPa

MPaJ

-78300/180

1100/950180/175

-161380/220

1450/1200160/160

-196400/220

1600/1350155/150

90090

Creep Data


Stress for a creep rate of 1% in 10 000 hours°C

MPa550120

60080

65050

70030

80010

Recommended Maximum Service Temperature

Continuous ServiceIntermittent Service

(Oxidising Conditions)925°C850°C

100050

Cr18.0 -20.0

18.0 -20.0

Ni8.0 -10.58.0 -12.0

Typical properties in annealed condition

1. Mechanical properties at room temperature Temperature °C 80°C


10

2000

20

2001

40

2002

60

2002

80

2111

100

2220

0 = resistant - corrosion rate less than 100um/year.1 = partly resistant - corrosion rate 100um to 1000um/year.2 = non-resistant - corrosion rate more than 1000um/year.

The performance of 304 compared with other metals is shown in the following table. Corrosion rates are based on 10 years exposure.

Thermal Processing Resistance

a. Annealing Heat from 1010°C to 1120°C and cool rapidly in air or water. For best corrosion resistance ensure the final annealing temperature is above 1070°C.b. Stress Relieving Stress relieve 304L at 450°C - 600°C for one hour with little danger of sensitisation. A low stress relieving temperature of 400°C maximum must be used for 304.C. Hot Working Initial forging and pressing 1150°C - 1260°C Finished temperature 900°C - 925°C Upsetting operation finish 930°C - 980°C

All hotworking operations should be followed by annealing.

Note: Soaking times to ensure uniformity of temperature are up to 1.5 times that required for the same thickness of mild steel.

316 / 316L Stainless Steel Data In-Depth



T R A D I N G

316 is an improved version of 304. The addition of molybdenum in 316 makes the steel more resistant. There is also a slightly higher nickel content. The result in a stainless steel with superior corrosion and oxidation resistance, good mechanical properties and a fabricability that takes advantage of its extreme toughness and ductility - to meet applications in many industries.Applications: Tanks and containers for: corrosive liquids, chloride contaminated media, acetic acid vapours. Specialised process equipment for chemical, food, paper, mining, pharmaceutical, and petroleum. Architectural applications in highly corrosive environments. Sea water and polluted marine environments.Benefits: 316 grade stainless steel offers: much increased corrosion resistance, higher strength and creep resistance at high temperatures, effective operating properties at sub-zero temperatures, and resistance to pitting and crevice corrosion in aggressive conditions.Fabrication: 316 / 316L is extremely tough, ductile and readily fabricated by cold working. Typical operations include: bending, forming, deep drawing, upsetting.Specify: 316L, the low carbon variety when there is a danger of corrosion in the heat-affected zones of weldments. 316Ti, titanium stabilised is used for its resistance to sensitisation during prolonged exposure in the 550°C - 800°C range.

Chemical Composition (ASTM A240)

316316L316Ti

2. Properties at elevated temperatures

The values given refer to 316 and 316Ti only as strength values for316L fall rapidly above 425°C.

Short time elevated temperature tensile strength

4. Corrosion Resistance - Aqueous

Atmospheric

For specific conditions, consult Macsteel Trading. As a roughguide, the examples are given for certain pure acid-water mixtures

C0.08 max0.03 max0.08 max

Mn2.0max

P0.045max

S0.030max

Si1.0max Temperature °C 20°C


Environment

RuralMarineMarine-industrial

3160.00250.00760.0051

Corrosion rate (um/year)Aluminium-3S

0.0250.4320.686

Mild Steel5.8

34.046.2

10

0000

20

1000

40

2000

60

2001

80

1011

100

0120

TypTensile StrengthProof Stress(0.2% offset)Elongation (%inL = 5.65/Sº)Hardness(Brinell)Erichsen CupTest valueEndurance(fatigue) limit

MPaMPa

mm

MPa

580310

55

165

8-10

260

Min316 316L 316Ti

515205

40

Typ570300

60

165

10-11

260

Min485170

40

Typ600320

50

165

260


°CMPa

600460

700320

800190

3. Properties at subzero temperature 316

TemperatureProof Stress(0.2% offset)Tensile StrengthImpact Str (Charpy V)

°CMPa

MPaJ

-78400

820180

-161460

1150165

-196580

1300155

900190

Creep Data


Stress for a creep rate of 1% in 10 000 hours°C

MPa550160

600120

65090

70060

80020

Recommended Maximum Service Temperature

Continuous ServiceIntermittent Service

(Oxidising Conditions)925°C870°C

100070

Min515205

40

Cr16.0

to18.0

Ni10.0

to14.0

Mo2.00

to3.0

Typical properties in annealed condition (see 304)

1. Mechanical properties at room temperature

Temperature °C 80°C


10

2000

20

2000

40

2001

60

2001

80

2111

100

2220

0 = resistant - corrosion rate less than 100um/year.1 = partly resistant - corrosion rate 100um to 1000um/year.2 = non-resistant - corrosion rate more than 1000um/year.

The performance of 316 compared with other metals is shown in the following table. Corrosion rates are based on 10 years exposure.

Thermal Processing Resistance

a. Annealing Heat from 1010°C to 1120°C and cool rapidly in air or water. For best corrosion resistance ensure the final annealing temperature is above 1070°C.b. Stress Relieving Heat from 200°C - 400°C and air cool.C. Hot Working Initial forging and pressing 1150°C - 1260°C Finished temperature 900°C+ Upsetting operation finish 930°C - 980°C

All hotworking operations should be followed by annealing.

Note: Soaking times to ensure uniformity of temperature are up to 1.5 times that required for the same thickness of mild steel.


NATIONAL BRANCH NETWORK

PIPES, FITTINGS & FLANGESTel: 011 821 5000Fax: 011 821 5030email: [email protected]

BLOEMFONTEINTel: 051 403 9400Fax: 051 403 9412/5email: [email protected]

CAPE TOWNTel: 021 950 5500Fax: 021 950 5600email: [email protected]

DURBANTel: 031 913 2600Fax: 031 902 2345email: [email protected]

EAST LONDONTel: 043 742 1440Fax: 043 742 1452/1449email: [email protected]

GEORGETel: 044 805 8300Fax: 044 874 3758email: [email protected]

GERMISTON SOUTHTel: 011 871 4600Fax: 011 871 4742email: [email protected]

KIMBERLEYTel: 053 840 0900Fax: 053 841 0323/0605email: [email protected]

KLERKSDORPTel: 018 406 8200Fax: 018 462 9527email: [email protected]

MANZINI (Swaziland)Tel: 00268 2518 4235/4625/4626/4381Fax: 00268 2518 5080/6265email: [email protected]

NELSPRUITTel: 013 752 5206Fax: 013 752 5208email: [email protected]

NEWCASTLETel: 034 375 5640/34Fax: 034 375 6154email: [email protected]

PHALABORWATel: 015 780 8000Fax: 015 781 5511email: [email protected]

POLOKWANETel: 015 292 1084Fax: 015 292 1072email: [email protected]

PORT ELIZABETHTel: 041 402 1960Fax: 041 486 1963email: [email protected]

PORT SHEPSTONETel: 039 682 3270Fax: 039 682 4420email: [email protected]

RICHARDS BAYTel: 035 797 6800Fax: 035 797 6810email: [email protected]

WELKOMTel: 057 391 1111Fax: 057 353 4303/357 1039email: [email protected]

MACSTEEL TRADING HEAD OFFICETel: 011 871 4600Fax: 011 871 4698/871 4692email: [email protected]

MACSTEEL SERVICE CENTRES SATel: 011 871 0000

We also stock a comprehensive range ofpipes, fittings and flanges in stainless steel

Date post:	11-Mar-2020
Category:	Documents
Upload:	others
View:	88 times
Download:	7 times

TRADING - Macsteel · TRADING The Macsteel Group - Africa’s leading steel supplier - PIPES,...

Documents