Training Calendar: Year 2015-16
Mitsubishi FA Products Training
Factory Automation Engineering Centre Factory Automation & Industrial Division
Mitsubishi Electric India Private Limited India
2
Index
1. TRAINING CENTRES ........................................................................................................................... 3
2. LIST OF REGULAR TRAINING COURSES ............................................................................................... 4
3. MITSUBISHI FA PRODUCT TRAINING CALENDAR: YEAR 2015-16 ......................................................... 5
4. DETAILED AGENDA OF REGULAR TRAINING COURSES: MELCO FA PRODUCTS ..................................... 6
FX PLC TRAINING ......................................................................................................................................... 6
GOT TRAINING ............................................................................................................................................. 7
Q PLC & CC-LINK BASIC TRAINING .................................................................................................................. 8
Q NETWORKING (ADVANCED NETWORKING) TRAINING ...................................................................................... 10
POSITIONING TRAINING ................................................................................................................................ 11
VFD (INVERTER) TRAINING ........................................................................................................................... 13
Q MOTION TRAINING .................................................................................................................................. 14
SIMPLE MOTION TRAINING ........................................................................................................................... 16
L SERIES PLC BASIC & BUILT IN POSITIONING TRAINING ..................................................................................... 17
IQR PLC TRAINING ..................................................................................................................................... 19
ROBOT TRAINING ........................................................................................................................................ 21
MC WORKS64 SCADA TRAINING ................................................................................................................. 23
5. DETAILED AGENDA OF REGULAR TRAINING COURSES: MEI FA PRODUCTS ........................................ 25
NEXGENIE 1000 PLC TRAINING ..................................................................................................................... 25
NEXGENIE 2000 PLUS PLC TRAINING ............................................................................................................. 27
GOC TRAINING .......................................................................................................................................... 29
6. CUSTOMIZED TRAINING PROGRAMMES .......................................................................................... 30
7. TRAINING CHARGES AND INSTRUCTIONS FOR REGISTRATION .......................................................... 31
8. TRAINING REQUEST FORM .............................................................................................................. 32
3
1. Training Centres Regular training is arranged at following centres:
Pune Centre
Mitsubishi Electric India Private Limited Factory Automation & Industrial Division, EL-3, J Block, MIDC Bhosari,
Pune, Maharashtra India – 411 026 Tel.: +91-20-2710 2000 Fax: +91-20-2710 2100
Gurgaon Centre
Mitsubishi Electric India Private Limited Factory Automation & Industrial Division,
2nd Floor, Tower A & B, DLF Cyber Greens, DLF Cyber City, DLF Phase III, Gurgaon, Haryana, India -122 002 Tel.: +91-124-4630300 Fax: +91-124-4630399
Bangalore Centre
Mitsubishi Electric India Private Limited Factory Automation & Industrial Division,
Prestige Emerald, 6th Floor, Municipal No. 2, Madras Bank Road, (Lavelle Road), Bangalore, Karnataka, India -560001 Tel: +91-80- 4020-1600 Fax: +91-80- 4020-1699
Chennai Centre
Mitsubishi Electric India Private Limited Factory Automation & Industrial Division, No.1 Vivekananda Road, Srinivasa Nagar Off Spur Tank Road, Chetpet Chennai, Tamil Nadu India – 600 031 Tel: +91-44-49232222 Fax: +91-44-49232249
Ahmedabad Centre
Mitsubishi Electric India Private Limited Factory Automation & Industrial Division, B/4, 3rd floor, Safal Profitaire, Corporate Road, Prahaladnagar, Satellite, Ahmedabad, Gujrat India – 380 015 Tel. : +91-79-65120063
www.MitsubishiElectric.in
Email: [email protected]
4
2. List of Regular Training Courses Following training courses are regularly offered from our all training centres mentioned in previous section.
No. Training
Code Duration
(Days) Brief Agenda
1 FX PLC 2 Includes FX3U/3G Basic and Advanced Programming, Analog interfacing using Blocks & ADP, and Interrupt Functions like Input, Timers and Counter
2 GOT 2 Includes GOT1000 / GT2000 series hardware, GT Designer programming, Basic & advanced features, Recipes & Alarms, Ladder Monitoring & Editing, Backup & Restore function. Different types of connections with PLC / Controllers, etc.
3 Q PLC 3 Includes QnUDEH/QnUDV PLC Hardware, Basic and Advanced programming, Analog I/O modules, programming using GxWorks2 and CC-Link Open network basic training.
4 Position 3 Includes positioning basics, FX Positioning using FX3U inbuilt high speed I/O and Positioning Instructions, Q Positioning using QD75 /QD77 modules (P/D/M/MH) with pulse type and SSCNET based servo amplifier.
5 Q Motion 3
Includes Mitsubishi make Q17nD/DS motion CPUs with MR-J4-B /J3-B type servo amplifiers, MT-Developer-II programming platform, Real Mode (SV13) and Virtual Mode (SV22), SFC programming, Mechanical System Editor, CAM configuration and monitoring and debugging.
6 Simple Motion
2 QD77MSn module range, Simple Motion Function, Configuration of Mechanical system, CAM design, operation, etc.
7 Q Network 3 CC-link advanced function like PLC to PLC communication, CC-Link IE : Field and control, MelsecNet/H : Control and remote I/O network
8 L PLC 3 Includes L series Hardware, Basic and Advanced programming using GXWorks2, Analog I/O modules, Inbuilt Position using pulse type servo like MR-JE/MR-J4A
9 iQR PLC 3 Includes R series PLC Hardware, Basic and Advanced programming, Analog I/O modules, programming using GxWorks3 and Open network basic training.
10 Robot 3
Introduction to MELFA Robot series and hardware, Types of Robot Controller and Manipulators Robot Mastering & Robot Parameters, Device configuration, Control power & Wiring of user control (CNUSR), Wiring of External Inputs and Outputs Operation panel, T/B, Jog operation, Hand operation.
11 VFD 2
FR-700 series of Inverters, Parameters, Configurations and Connections for Signal & Power, V/F control, FR-Configurator, Error & Warnings, Troubleshooting, Accessories like reactors & BU, Communication with PLCs though Serial, CC-Link, other protocols, Advanced Features, Energy Saving Drives, etc.
12 MC Works 2 Introduction to MC Works64 , Architecture of MC Works64 OPC Tags, Data Connections & Browsers, Customizing the Workbench, GraphWorx64 Layout & Screen Designing & Alarm Generation.
13 NG1K 2 Nexgenie 1000 PLC hardware, Base & Expansion Units, Memory Organization, DI/DO and Analog I/O, Connection & Configuration, Programming using CoDeSys, Troubleshooting & Maintenance issues, etc.
14 NG2KP 3
Nexgenie 2000PLUS PLC hardware, Base & Expansion Modules, Memory Organization, DI/DO and Analog I/O, Connection & Configuration, Programming using CoDeSys, Modbus Network, Communication FBs, Troubleshooting & Maintenance issues, etc.
15 GOC 2 Includes GOC series hardware, PLC programming, HMI Screen Design /Various Objects, third party connectivity, etc.
5
3. Mitsubishi FA Product Training Calendar: Year 2015-16
2 days 2 days 3 days 3 days 3 days 2 days 3 days 3 days 3 days 3 days 2 days 2 days 2 days 3 days 2 days
Pune 13-14 15-16 20-22 27-29
Gurgaon 27-28 29-30 13-15 20-22
Bangalore 20-21 22-23 16-17 1-2
Chennai 27-29 15-17 1-3
Ahmedabad 13-15 20-22 1-2
Pune 27-29 7-8 18-20 14-15
Gurgaon 18-20 25-27 7-8 11-12
Bangalore 25-27 18-20
Chennai 11-13 25-26
Ahmedabad 11-13 4-5
Pune 1-2 3-4 22-24 15-17 29-30 11-12
Gurgaon 1-3 15-16 22-24 25-26
Bangalore 22-24 1-3
Chennai 1-2 3-4 15-16 22-24 29-30
Ahmedabad 1-2 3-4 15-17
Pune 20-22 1-3 13-15 27-29
Gurgaon 27-28 29-30 13-15 20-22 1-3
Bangalore 13-14 15-16 20-22 27-29 1-3
Chennai 13-14 15-16 27-29 2-3
Ahmedabad 27-29 13-15 2-3
Pune 17-18 19-20 24-26 6-7
Gurgaon 24-26 17-19 10-11 6-7
Bangalore 17-19 24-26 3-4
Chennai 10-12 24-25
Ahmedabad 17-18 10-11 3-4
Pune 2-4 28-30 21-23 14-16 10-11
Gurgaon 23-25 2-4 14-16 28-30
Bangalore 14-16 28-30 2-4 21-23 7-8
Chennai 14-16 28-29
Ahmedabad 1-2 3-4 21-23 14-16
Pune 26-27 28-29 19-21 8-9 15-16
Gurgaon 19-21 26-28 12-13 8-9
Bangalore 26-27 28-29
Chennai 12-14 26-28 19-20
Ahmedabad 12-14 19-21 5-6
Pune 23-25 2-4
Gurgaon 23-24 2-4 9-10
Bangalore 2-4 23-25
Chennai 23-24 25-26 2-4
Ahmedabad 23-25 2-4
Pune 1-2 3-4 21-23 14-16 10-11 28-30
Gurgaon 14-15 16-17 21-23 2-4 28-30
Bangalore 28-29 21-23 2-4 7-8
Chennai 2-4 14-16 28-29 21-22
Ahmedabad 1-2 3-4 21-23 14-15
Pune 11-13 27-29 18-20
Gurgaon 18-20 11-13 27-29
Bangalore 11-12 13-14 20-22 27-29
Chennai 11-12 13-14 27-29
Ahmedabad 11-13 20-22 27-29
Pune 15-16 17-18 22-24 4-5 11-12
Gurgaon 22-23 24-25 15-17 11-12
Bangalore 3-5 22-24 8-9
Chennai 15-17 1-2 22-23
Ahmedabad 15-16 17-18 8-9
Pune 14-16 21-23 28-30 2-4
Gurgaon 28-30 2-4 14-16 21-23
Bangalore 14-15 3-4
Chennai 2-4 14-16
Ahmedabad 21-23 3-4
Oct
‘15
No
v ‘1
5D
ec
‘15
Jan
‘16
Feb
‘16
Mar
‘16
MC
WorksNG1K NG2KP GOC
Ap
ril ‘
15
May
‘15
Q
Network
Simple
Motion Q MotionQ PLC Position L PLC iQR PLC Robot VFDMonth
Jun
‘15
July
‘15
Au
g ‘1
5Se
pt
‘15
FA Centre
Training Modules
FX PLC GOT
6
4. Detailed Agenda of Regular Training Courses: MELCO FA Products
FX PLC Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of PLC, Basics of Electrical & Electronics etc.
Duration Two days
Training Session Timing Training Time 09:30 am to 05:00 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 2:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 01:00 pm Review of Number Systems, Basics of PLC and PLC SCAN FX Series Hardware Review
Range of PLCs like FX3U /FX3G, Different types of blocks/expansion module
Discrete I/O, Sourcing & Sinking, Relay & Transistor Type
PLC Memory, PLC Devices and I/O Addressing PLC Programming : GX Works 2
Project Creation / Project Editor
Transfer setup / Upload / Download
Relay Based Instructions and Timers & Counters
Monitoring & Editing Practice
02:00 pm to 05:00 pm PLC Programming
Grouping of bit devices, indexing registers
Data transfer instructions & Arithmetic instructions
Logical / comparison instructions Practice
Day 2
09:30 am to 01:00 pm Analog Input / Output Blocks
Range of analog blocks
FX3U-4AD and FX3U-4DA modules
Specification, wiring and configuration, interfacing with BFMs Analog Input / Output Adapters
Range of Analog Adapters
FX3U-4AD-ADP and FX3U-4DA-ADP
Specifications, wiring and Configuration, Special D/M devices Practice
02:00 pm to 04:30 pm Advanced Programming
Program control instruction : CJ, For-Next and Call Interrupts
Input interrupts & Timer interrupts
High speed counter & counter interrupts Practice
04:30 pm to 5:00 pm Feedback / Interaction / Self evaluation
7
GOT Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of PLC, Basics of Electrical & Electronics etc.
Duration Two Days
Training Session Timing Training Time 09:30 am to 05:00 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 2:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 05:00 pm GOT Hardware overview GT Designer software
New project creation
Configuration of GOT communication with PLC
OS selection and installation: Boot OS, Standard monitor OS, Communication driver,
Different types of Screen
Various Objects like switch / lamps / Text and Numerical display, various graphs; and other objects
Part Display & Part routes
Comments / Comment groups / Comment display
User Alarms: Alarm configuration & Alarm Display
Objects from Library Practice
Day 2
09:30 am to 04:30 pm GT Designer software
Recipe,
Scripts: Project & Screen scripts
Logging function, Time Action,
System Alarms & Advanced Alarms
Document Display, Network Monitoring
Backup restoration: GOT & PLC programs
Intelligent Module monitoring
List Monitor & Editor
Ladder Monitoring & Editor
One-touch ladder jump function, PLC Diagnosis on GOT
Different communication options like CC-Link, Ethernet and Q-Bus connection
Practice
04:30 pm to 05:00 pm Feedback / Interaction / Self evaluation
8
Q PLC & CC-Link Basic Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of PLC, Basics of Electrical & Electronics etc.
Duration Three Days
Training Session Timing Training Time 09:30 am to 05:00 pm Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm Lunch Time 01:00 pm to 02:00 pm
Duration Activity / Contents Day 1 09:15 am Registration 09:30 am to 01:00 pm Basics of PLC
Introduction of QnU/QnUDV series PLCs hardware Discrete I/O modules, sourcing and sinking connections PLC memory drives, device memory, special devices (SM/SD) Addressing of I/O
PLC Programming : GX Works2 Simple Project mode
Transfer setup: RS232/USB/Ethernet Project upload & download Relay based instructions Timers & Counters Monitoring & Editing
Practice
02:00 pm to 05:00 pm PLC Programming
Data transfer instructions Arithmetic instructions
Logical and comparison instructions In-line ST programming
Practice
Day 2 09:30 am to 01:00 pm Advanced Programming
Grouping of Bit devices and Indexing Program control instruction: Call and Subroutines, Jump, For-Next Loop
instructions
Multiple programs
File registers
Memory Card : file registers & program backup and booting Practice
9
Duration Activity / Contents Day 3 09:30 am to 01:00 pm CC-Link Basics
CC-Link module specification and features
Wiring of remote I/O module
Remote I/O stations & remote Device Stations
Hardware test of QJ61BT11N module
Troubleshooting and practical session Practice
02:00 am to 04:30 pm Introduction of Structure Programming (IEC-61131-3)
Different Editors : Structure Ladder, FBD, Ladder and ST
POU Types: Program, Function and Function Block
Standard and User Library Practice
04:30 pm to 05:00 pm Feedback / Interaction / Self evaluation
10
Q Networking (Advanced Networking) Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of PLC, Basics of Electrical & Electronics etc.
Duration Three Days
Training Session Timing Training Time 09:30 am to 05:00 pm Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm Lunch Time 01:00 pm to 02:00 pm
Duration Activity / Contents Day 1 09:15 am Registration 09:30 am to 01:00 pm Q PLC Overview
Overview of Q Hardware and I/O addressing
GX-Works2 Programming Software overview CC-Link
Specifications Configuration for Remote I/O and Remote Device Stations
PLC to PLC communication using Local Stations
Practice 02:00 pm to 05:00 pm CC-Link IE Field network
Specifications Configuration for Remote I/O stations
Configuration for Local Station Practice
Day 2 09:30 am to 01:00 pm CC-Link IE Field network (cont.)
Configuration for head module (L series I/O) I/P packet transfer using CC-Link IE Field network
Practice
02:00 pm to 05:00 pm CC-Link IE Control Network
Specifications Configuration of Control stations and normal stations
Practice
Day 3 09:30 am to 01:00 pm 02:00 pm to 04:30 pm
MelsecNet/H
MelsecNet modules range, specification and features
Configuration and wiring Optical loop and coaxial connections
PLC to PLC communication Remote I/O network
Remote To/From instructions Hardware Test of MelsecNet/H modules
Practice
04:30 pm to 05:00 pm Feedback / Interaction / Self evaluation
11
Positioning Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of
PLC, basics of induction Motor, etc. Participant must be well familiar with FX PLC and QPLC basics
Duration Three Days
Training Session Timing Training Time 09:30 am to 05:15 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 02:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 01:00 pm Basics of Positioning Pulse Type Servo Amplifier : MR-E Super /MR-JE / MR-J3/J4-A
Specification and parameters
Power connection guideline
Signal connections with positioning controllers like FX3U / QD75P/D
Display, monitoring and test operation
Troubleshooting : Alarms & warnings MR-Configurator
Setup software for Testing / Setting / Parameter Backup Practice
02:00 pm to 05:00 pm Positioning using FX3U PLC
FX3U inbuilt High speed I/O and FX3U High Speed Adapters
Positioning Instructions & FX3U Table Instructions Practice
Day 2
09:30 am to 01:00 pm SSCNET based Servo System : MR-J3 /MR-J4B
Specification and Parameters
SSCNET connection with positioning controllers like QD75MH /QD77MS Product Range : QD75P/D/M/MH /QD77MS
Specifications
External Signal Connections : DOG, STOP/Change, FLS and RLS
I/Os : Positioning status and commands Practice
02:00 pm to 05:00 pm QD77 MS /QD75MH
Positioning parameters , Monitoring data & Control data
JOG operations
Homing operation : Different types of homing
Errors monitoring & error correction logic Practice
12
Duration Activity / Contents
Day 3
09:30 am to 01:00 pm 02:00 pm to 04:30 pm
QD75MH /Q77MS
Point to point Control : Using buffer memory
Various positioning functions: INC/ABS, Interpolation, VF / VR etc.
M-Code
Current value change function
Speed override function
Teaching Instruction Expansion Function of QD77MS
Speed –Position-Torque control mode change over function Practice
04:30 pm to 05:00 pm Feedback / Interaction / Self evaluation
13
VFD (Inverter) Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of PLC, basics of induction Motor, FX Series Basics and Q PLC Basics etc.
Duration Two Days
Training Session Timing Training Time 09:30 am to 05:00 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 02:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 01:00 pm Mitsubishi Inverter : 700 Series
Basics of inverter
Mitsubishi range of inverters
Inverter Selection
Power and signal connections V/F Control
Operation
Parameters
Different types of load patterns
Different mode of operation: PU, Net, External etc.
Jog operation Practice
02:00 pm to 05:00 pm FR-Configurator
Parameters setting
Backup, Monitoring, trends Auxiliary Components Troubleshooting
Error & Warning Codes Practice
Day 2
09:30 am to 01:00 pm Networking of VFD
FX3U & VFD using RS485 /232 BD
VFD on CC-LINK using F7NC
Modbus Option Practice
02:00 pm to 04:30 pm Energy Saving Using VFD : F700 series Advanced Features of Mitsubishi VFD
4:30 pm to 05:00 pm Feedback / Interaction / Self evaluation
14
Q Motion Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of Q PLC, Addressing of I/O, basics instructions, GX Developer, fundamentals of Positioning, basics of induction motors and encoder, drive principle, etc. Participants must have gone through positioning training..
Duration Three Days
Training Session Timing Training Time 09:30 am to 05:15 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 02:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 01:00 pm 02:00 pm to 05:00 pm
Overview of Mitsubishi Range of Servo Controllers SSCNET Based Servo Systems
Basics of servo systems
Servo amplifier MR-J3B /MR-J4B /MR-J4WB
Connections : SSCNET, external signals and power Connections
Parameters Q17nD/DS Q170M/MS Motion CPUs
Range of motion CPUs: specifications and configurations
Motion Specific Modules : Q172DEX / Q173DPX / Q172DLX OS installation procedure Special relays & registers of motion CPUs MT Developer - 2
New project creation
Basic system setting
Multiple CPU data sharing setting
Fixed parameters and parameter blocks
Servo parameters Practice
Day 2
09:30 am to 01:00 pm 02:00 pm to 05:00 pm
SFC Programming
SFC Specifications
SFC programming Steps (F /FS/G etc)
Instructions for F/G Steps
Servo program (K) and various instruction Exercise
Homing using different homing methods like Near point Dog, Data set, etc
Single axis positioning in real mode
Interpolation : Linear, Circular
VF/VR instructions Practice
15
Duration Activity / Contents
Day 3
09:00 am to 01:00 pm 02:00 pm to 04:30 pm
Motion Control: Virtual Mode
Special bits and registers for virtual axis
Servo Program allocation for Virtual Control
Real to virtual mode transition
Configuration of virtual axis
Simultaneously operation of virtual and real axis Mechanical Editor
Input Modules : Servo motors (virtual axis) / Synchronous encoders
Connecting Modules :Different types of gears, Clutches, Differential gears and speed gears
Output Modules : Rotary Table, Roller, Ball Screw & CAM CAM Editor
CAM Design : Feed CAM & Reciprocating CAM Practice
04:30 pm to 05:00 pm Feedback / Interaction / Self evaluation
16
Simple Motion Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of
Q PLC, Addressing of I/O, basics instructions, GX Developer, fundamentals of Positioning, basics of induction motors and encoder, drive principle, etc. Participants must have gone through positioning training..
Duration Two Days
Training Session Timing Training Time 09:30 am to 05:00 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 02:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 01:00 pm 02:00 pm to 05:00 pm
Overview :
Mitsubishi Range of Servo Controllers
SSCNET Based Servo Systems
Overview of QD77 Specifications overview QD77MS Configurations
Parameters
Servo parameters Settings
Positioning Parameters
Input Axis Parameters
Synchronous Parameters with single virtual axis and linear cam
Jog, Home and error correction program
Synchronous operation using Sequence program CAM Design
CAM types, Resolutions, Stroke units, and other parameters
Configuration of different types of CAM
Selection of CAM for Output axis Practice
Day 2
09:30 am to 01:00 pm 02:00 pm to 04:30 pm
Synchronous parameters in Details
Auxiliary Virtual Servo and encoder axis
Clutches, electronic gears, differential gears, speed change gears
Exercises using different components of synchronous motion CAM Auto generation Function
Control data for Auto generation of CAM
Execution of Auto CAM for rotary axis CAM Position Restoration function Practice Troubleshooting and Monitoring
04:30 pm to 05:00 pm Feedback / Interaction / Self evaluation
17
L series PLC Basic & Built in Positioning Training
Training Session Timings
Training Timings 09:30 am to 05:30 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 1:00 pm to 02:00 pm
Duration Activities/Contents
Day 1
09:15 am Registration
09:30 am to 01:00 pm Review of Number Systems, Basics of PLC and PLC SCAN L Series Hardware Review
Introduction of L series PLCs hardware
L series built in I/O functionality
Discrete I/O modules, sourcing and sinking connections
PLC memory drives, device memory, special devices (SM/SD)
Addressing of I/O
PLC Parameter Settings
01:00 pm to 05:00 pm PLC Programming : GX Works2
Simple Project mode
Transfer setup: RS232/USB/Ethernet
Project upload & download
Relay based instructions
Timers & Counters
Monitoring & Editing Practice
Day 2
09:30 am to 01:00 pm Analog Input / Outputs Module
Range of Analog Modules
Connections, buffer memory, configuration
BFM interface : To/From instructions, Un\Gm addressing
Intelligent Module Configuration –AD/DA Practice
02:00 pm to 5:00 pm Advanced Programming
Grouping of Bit Devices
Program Control Instruction: CALL and Subroutine, Jump, For-Next Loop instruction
Multiple Programs, Program types
Memory Card: File register, Program Backup and booting
L series Data Logging function Practice
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of PLC, Basics of Electrical & Electronics etc .
Duration Three Days
18
Duration Activity/Contents
Day 3
09:30 am to 01:00 pm Introduction to Built-in Positioning with Pulse Type Servo :MR-JE/MR-J4-A
Introduction to built-in positioning features.
Connections, Configuration & Parameter Setting
Basic Operations: Homing & Jogging Practice
02:00 pm to 4:30 pm Introduction to Pulse Positioning
Pulse Positioning profile creation
Positioning table creation , execution
Various Positioning Commands
Monitoring, Troubleshooting Practice
4:30 pm to 5:00 pm Feedback / Interaction / Self evaluation
19
iQR PLC Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of PLC, basics of Networking, RS232 and RS485 protocols, Label Programming etc.
Duration Three Days
Training Session Timing
Training Time 09:30 am to 05:00 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 02:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 01:00 pm Basics of MELSEC IQR Series hardware
Introduction of iQ-R PLC hardware, Features, Specifications
System Configuration, Various Modules in Line-up
MELSEC iQ-R Series Product outline
Difference between Q Series and iQ-R
Compatibility with existing product line up
I/O Addressing Practice
02:00 pm to 05:00 pm PLC Programming: GX Work3
Introduction of GX Works 3 software
Creating New Project
System Configuration
Intuitive Program (Drag & Drop)
Using built-in library
3rd Party Partner Library Practice
Day 2
09:30 am to 01:00 pm PLC Programming: GX Work3
Creating New data & setting of labels
Creating FB Program and Techniques for creating FBs
Utilizing FBs in other project
E Manual Viewer Practice
02:00 pm to 05:00 pm Analog Input / Outputs Module/Intelligent Function Module
Range of Analog Modules /Intelligent function module
Connections, buffer memory, configuration
Module Library
Use of Module labels for programming of A/D,D/A & Other Intelligent
Changing module slot and reflecting IO assignment Practice
20
Duration Activity/Contents
Day 3
09:30 am to 01:00 pm Introduction to Embedded Data Base
Recipe and Production data management
Dedicated commands Like DB.INSERT, DB.SELECT
Program example Practice
02:00 pm to 04:30 pm Maintenance & Security function
Data Logging & Analysis
Memory Dump Function
Quickly find network errors
Prevent system downtime with relay monitoring
Security key protection
Access control by IP address/password
Event Log History Practice
04:30 pm to 05:00 pm Feedback / Interaction / Self evaluation
21
Robot Training
Prerequisites Participants are expected to know the Coordinates, Basics of Electronics and Pneumatics.
Duration Three Days
Training Session Timing
Training Time 09:30 am to 05:00 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 02:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 01:00 pm Robot Safety related Laws
Industrial robot safety Basics of Robot
Introduction to MELFA Robot series and hardware
Types of Robot Controller and Manipulators
Robot Mastering
Robot Parameters
Device configuration, Control power
Wiring of user control (CNUSR)
Wiring of External Inputs and Outputs
Operation panel, T/B
Jog operation, Hand operation Moving the robot with jog operation
Joint, Cartesian, Tool jog operation
Opening/closing the hand, etc. Practice
02:00 pm to 05:00 pm Introduction to RT Toolbox2 Software
Robot Configuration using RT Toolbox
RT Toolbox Options Robot Programming language
MELFA-BASIC V specifications
Constants, variables, common variables, etc.
Program instructions
Command functions Practice
Day 2
09:30 am to 01:00 pm Robot Programming Using Teach Pendant
Basic operation of the T/B
Programming and teaching the positions
Revising, adding and deleting program instructions
Confirming the registered position data operation
Automatic operation Practice
22
Duration Activity / Contents Day 2
02:00 pm to 05:00 pm Robot Programming using RT Toolbox2 Software
Instruction Edit screen/Position Edit screen
Editing, teaching, compensating, etc.
Programming and teaching the positions
Revising, adding and deleting program instructions
Confirming the registered position data operation
Automatic operation
Debugging Robot Application Programming
Robot Pick and Place
Robot Pallet Operation Practice
Day 3
09:30 am to 01:00 pm Robot Application Programming
Robot Linear and Continuous path programming
Robot Machine tending Practice
02:00 pm to 04:30 pm Robot Communication Options Robot Maintenance and Alarms
04:30 pm to 5:00 pm Feedback / Interaction / Self evaluation
23
MC Works64 SCADA Training
Prerequisites Participants are expected to know the basics of PLC, Configuration, Tags and OPC Server.
Duration Three Days
Training Session Timing
Training Time 09:30 am to 05:00 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 2:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 10:45 am
11:00 am to 01:00 pm
Introduction to MC Works64
Introduction to MC Works64
Architecture of MC Works64
Modes: Configuration vs Runtime
Programmable logic devices and OPC Servers
OPC Tags
Data Displays
Data Connections & Browsers
Microsoft Silverlight and Windows features Workbench
Introduction to the workbench
Customizing the workbench
Creating a project
Configuration and layout Management
Project management Tools
Workbench Runtime Practice
02:00 am to 05:00 pm GraphWorX64 Basics
GraphWorx64 Layout
The object Explorer
The property Explorer
Customizing Workspace using the View Tab Ribbon
Templates and Transitions
Symbol Library
Basics 2D shapes and objects
Dynamics & Object count
Application Mode
Display password protection Practice
24
Duration Activity/Contents
Day 2
09:30 am to 01:00 pm Alarm WorX64 Server & Viewer
Alarm Tags
Configuring Alarm Tags
Group Alarm Tags by Area Importing & Exporting Components
Configuring the Viewer
Adding Tabs, Alarm subscription to Tabs
Tab properties
Text Translation
Alarm Viewer Runtime Options Practice
02:00 pm to 04:30 pm GraphWorX64 Tools
MC Works64 Controls
Search and Replace
Arranging Controls and Objects
Views
GraphWorx64 Runtime Ribbon and Menus Practice
04:30 pm to 5:00 pm Feedback / Interaction / Self evaluation
25
5. Detailed Agenda of Regular Training Courses: MEI FA Products
Nexgenie 1000 PLC Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of PLC, Basics of Electrical & Electronics etc.
Duration Two Days
Training Session Timing
Training Time 09:30 am to 05:00 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 2:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 10:45 am
Review of Number Systems, Basics of PLC and PLC SCAN MEI PLC Product Range Overview Nexgenie 1000 PLC Hardware Review : Nexgenie 1000 PLC : Base Blocks
NG16DL / NG16ADL / NG14RL / NG14 RN / NG16DN Introduction Of Base blocks – serial ports, I/O wiring connector
Different types of digital expansion module NE16DX / NE14RX / NE08X / NE06RX / NE08DX
Discrete I/O, Sourcing & Sinking, Relay & Transistor Type Sinking & sourcing wiring Explanation Relay & Transistor Type wiring Explanation
PLC Memory, PLC Devices Different Types Of Memory & its size Marker Memory, Data Memory, File Marker Memory Application memory
For Execution Application Program Code Memory for Permanent Storage Application Program source code memory for Permanent storage
Addressing : I/O ( Symbolic & Absolute Addressing ) & Marker Memory I / Q / M Memory addressing Memory Mapping : Explanation of Memory Mapping Byte , Word & Double Word Symbolic Addressing
Practice
11:00 am to 01:00 pm
PLC Programming : CoDeSys Brief Explanation about Programming Software – CoDeSys o System Requirement & Installation
POU & Main PRG Explanation Programming Languages – LD , IL , ST , FBD Possibility of Conversion Configuration Of PLC
26
Duration Activity / Contents
11:00 am to 01:00 pm
PLC Programming : CoDeSys Cont… Project Creation / Project Editor Transfer setup / Upload / Download Relay Based Instructions and Timers & Counters Monitoring & Editing - Simulation Mode Visualization
Practice
02:00 pm to 05:00 pm PLC Programming Data transfer instructions Arithmetic instructions Logical / Comparison instructions
Practice
Day 2
09:30 am to 01:00 pm Analog Input / Output Expansion Modules Range of Analog blocks NE40UX , NE42UX , NE02AX & NG16ADL Specifications & Wiring Program Configurator Programming
Practice
02:00 pm to 04:30 pm Interrupts Input , Timer interrupts
Troubleshooting Offline – LED diagnostics & Online - System Variables
Practice
04:30 pm to 5:00 pm Feedback / Interaction / Self evaluation
27
Nexgenie 2000 Plus PLC Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of PLC, Basics of Electrical & Electronics etc.
Duration Three Days
Training Session Timing
Training Time 09:30 am to 05:00 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 2:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 10:45 am
Review of Number Systems, Basics of PLC and PLC SCAN MEI PLC Product Range Overview Nexgenie 2000 Plus PLC Hardware Review
Range of CPUS, Base racks Range of different types of module Discrete I/O, Sourcing & Sinking, Relay & Transistor Type Sinking & sourcing wiring Explanation Relay & Transistor Type wiring Explanation
PLC Memory, PLC Devices
Different Types Of Memory & its size Marker Memory
Data Memory File Marker Memory Application memory
For Execution Application Program Code Memory for Permanent Storage
Application Program source code memory for
Permanent storage Addressing : I/O ( Symbolic & Absolute Addressing ) & Marker Memory
I / Q / M Memory addressing Memory Mapping : Explanation of Memory Mapping Byte , Word & Double Word Symbolic Addressing
Practice
11:00 am to 01:00 pm
PLC Programming : CoDeSys Brief Explanation about Programming Software – CoDeSys o System Requirement & Installation
POU & Main PRG Explanation Programming Languages – LD , IL , ST , FBD Possibility of Conversion Configuration Of PLC Project Creation / Project Editor Transfer setup / Upload / Download Relay Based Instructions and Timers & Counters Monitoring & Editing - Simulation Mode Visualization
Practice
28
Duration Activity / Contents
02:00 pm to 05:00 pm
PLC Programming Data transfer instructions Arithmetic instructions Logical / Comparison instructions
Practice
Day 2
09:30 am to 11:00 am PLC Programming (Contd.) Export & Import Feature
Export/Import of POU, FB and Global Variables
Visualization, Watch & Recipe Manager, Configuration. Save / Print POUs
Practice
11:00 am to 05:00 pm Analog Input / Output Modules
Range of analog modules,
Specification, wiring and configuration Program Configurator
Programming using IM Read & IM Write Function Blocks Practice
Day 3
09:30 am to 01:00 pm Modbus Function Module Master Configuration Remote I/O Module (Rix) Connection & Configuration Application Examples: Mitsubishi Inverter / Energy Meters, etc.
Modbus Slave Function
Programming : Communication FBs Practice
02:00 pm to 04:30 pm Interrupts Input interrupts
Timer interrupts Troubleshooting Practice
04:30 pm to 05:00 pm Feedback / Interaction / Self evaluation
29
GOC Training
Prerequisites Participants are expected to know the number systems (Binary, Hex, BCD), basics of PLC, Basics of Electrical & Electronics etc.
Duration Two Days
Training Session Timing
Training Time 09:30 am to 05:00 pm
Tea Time 10:45 am to 11:00 am and 03:30 pm to 03:45 pm
Lunch Time 01:00 pm to 2:00 pm
Duration Activity / Contents
Day 1
09:15 am Registration
09:30 am to 05:00 pm Review of Number Systems, Basics of PLC and PLC SCAN MEI PLC Product Range Overview Graphic Operation Controller (GOC) Hardware Review
Nomenclature and salient features
Main Unit, Extension Unit – I/O Extension & COM Extension Discrete I/O Wiring GOC Memory & Devices
- Different types of memory & their sizes, Marker memory, Data
memory, Application Memory & Source code
11:00 am to 01:00 pm PLC Programming : CoDeSys Brief Explanation about Programming Software
POU & Main PRG Explanation
Programming Languages – LD , IL , ST , FBD Practice
02:00 pm to 05:00 pm PLC Programming Data transfer instructions
Arithmetic instructions
Logical / Comparison instructions Practice
Day 2
09:30 am to 01:00 pm Analog Input / Output Expansion Modules Range of Analog expansion module
Specifications, Wiring & Configuration
Programing Practice
02:00 pm to 04:30 pm HMI Function Highlighting features
Screen
Data Entry
Function Keys System Variables Practice Troubleshooting
04:30 pm to 05:00 pm Interaction / Feedback / Evaluation
30
6. Customized Training Programmes We also conduct training on following products as per customer’s requirements at our FA centres or customer’s site:
MELCO FA Products Training List
Training Module Brief Agenda
FX Networking Serial Communication Boards/ Adapters, 1:N & N:N communications, Inverter Network with FX3U / FX3G PLCs, CC-Link for FX PLC : Master & Salve Blocks, Ethernet Module : FX3U-ENET
FX Third Party communications
Modbus communication using FX3U-232 /485 ADP-MB
FX Positioning Blocks FX2N-1PG /FX2N-10PG FX3U-20SSCH: SSCNET-III based module for MR-J3-B servo amplifier
Q Third Party Communications
Modbus: Serial & TCP/IP, DeviceNet / Profibus / Others
Redundant CPU Q12PRH / Q25PRH Redundancy CPUs, Programming & Parameter Setting for redundancy
IQ Platform Integrated Programming Platform for PLC, HMI and Motion. This includes MELSOFT Navigator, GX Works-2, MT Works-2, GT Works-3
Q170MSCPU 16 Axis Motion & Sequence CPU combined controller, MT-Developer-2, SSCNET-III based servo amplifier
MR-MQ100 Standalone 1½ Axis Motion Controller, MT-Developer-2, SSCNET-III based servo amplifier
MR-J3-T CC-link based Servo Amplifier of MR-J3 Series
L series PLC training L Series PLC hardware, Range of CPUs, I/O modules, Analog Modules, Networking modules, etc, I/O addressing, Programming using GxWorks2,
L Basic Positioning L series Built-in Positioning, High speed inputs/outputs, Encoder Interfacing, Interfacing with pulse input type servo amplifiers, Homing, Jogging, and positioning, practice
L Advance Positioning LD75MH and LD77MS modules, SSCNET based Servo controllers, Simple Motion control, etc.
VFD A800 Training Series Comparison of A700 & A800, A800 functions, A800 Inverter Controls – V/F, Advanced magnetic flux controls, Configuration of VFD ,FR Configurator2, Networking of VFD, Troubleshooting of VFD
MEI FA Products Training List
NG5K Training Nexgenie 5000 PLC, hardware overview, PLC memory, Different types of I/O modules, Programming using CoDeSys, Analog I/O module interface, CAN Open communication interface, practice, etc.
Advanced Training PTO/HSC using NG2KP and NG5K PLC, Interfacing with Servo Amplifiers, Motion Function Library, etc.
Networking Training CAN OPEN, MODBUS and Ethernet Communication feature in NG2KP / NG5K series PLCs, third party connectivity, GPRS,
SL HMI Training Different Types of Text HMI: JR HMI, JR Ex HMI, SR Ex HMI, Sr HMI., SL Designer Programming software, message configuration, key configuration, etc.
MS-HMI MS Series HMI- Hardware overview, MS Designer, Projects Creations, Screen Development, Various Objects, Alarms, Library Menu, Recipe Function, Data logging Function, Macro, 3rd Party Connectivity, etc.
Please contact training department for detailed agenda and schedule for above training programs.
31
7. Training Charges and Instructions for Registration
1. Regular training programs are conducted as per the calendar.
2. Training Charges for Regular Training Courses at MEI FA centres:
No. Duration of training (Days)
Charges (INR)
1 One Day 5500/-
2 Two Days 8000/-
3 Three Days 10000/-
4 Four Days 11500/-
3. Service tax is extra as applicable.
4. These charges are applicable to all regular training courses on Mitsubishi FA products.
5. Training venue can be selected from the list of FA centres mentioned in brochure. The same
charges are applicable for all the FA centres.
6. Accommodation and transportation will be arranged by the participants.
7. Fees once paid will not be refunded. Registration can be transferred to other participants
from the same company with prior intimation to the Training Department.
8. For the registration, please send duly filled ‘Training Request Form’ as given on following
page to nearby training centre or below centre :
Factory Automation Engineering Centre (FAC)
Factory Automation & Industrial Division,
Mitsubishi Electric India Private Ltd.,
EL-3, J Block, MIDC, Bhosari, Pune-411 026
Email: [email protected]
9. Registration is to be done minimum Two Weeks in advance with full payment of the training
fees.
10. We also offer wide range of training modules for Mitsubishi Factory Automation Products.
11. Please contact us for customized training required at site as well as if training requirement is
other than regular training courses.
32
8. Training Request Form
To be filled by training requester / applicant
Applicant Details:
Details for requested course :
Participants from the same organization / department :
No.
I declare that the above information is correct and participants fulfil the prerequisites for the mentioned courses.
Place:
Date: (Signature of Applicant)
Further Communication / Action Required:
Quotation ( ) / PO Received ( ) / Date Confirmation ( )
Site Visit Required ( )
9
7
6
5
Name of Participant Designation Department
2
1
4
3
Training Agenda
Training Type Regular as per MEI Training Calendar ( ) / Customized ( )
Expected Schedule
Preferred Location
Total No. of Participants
Training Request Form
Mitsubishi Electric India Pvt. Ltd.
MEI Pune ( ) / MEI Gurgaon ( ) / MEI Bangalore ( ) / MEI Chennai ( ) / MEI Ahmedabad ( ) or
Customer Site ( ) (Specify the location if customer site is selected)
Department
Organization
Name of Applicant
Designation
Contact Details Mobile : Email :
8
10
Mitsubishi FA Product Used :
For Internal use only at Mitsubishi Electric India Pvt. Ltd.
Format No. MEI/FAC/TR/001
Payment Details :
Tel: (020) 27102000, Fax: (020) 27102100
Email : [email protected]
Request:-Kindly fill this form and send either hardcopy to below address or email scan copy.
Contact Address : FAC, FAID, Mitsubishi Electric India Pvt. Ltd, EL-3, J Block, MIDC Bhosari, Pune - 411 026
Planned Date: Allotted Engineer / Faculty for training: