MARKING & INSPECTION

Training Labelling, marking and inspection solutions

Quality, functionality and performance have the

highest priority for our development engineers.

But how can the potential of your machine be fully

exploited? How do you ensure operation runs

smoothly? How do you ensure optimum safety?

Our training experts answer these questions for you.

You will become familiar with the reliable handling of

MULTIVAC labelling, marking and inspection solutions.

You will learn how the optimum production readiness

of your labellers, printers and inspection systems can

be achieved step-by-step. Practical information and

tips help to avoid operating errors, and to quickly

detect and rectify faults.

3

4

Training courses at MULTIVAC Marking & Inspection

... know how it works!

A training course in our factory in Enger offers the advantage, that technicians can devote themselves to their training in a concentrated way, if they have been relieved of the demands of their regular duties.

In addition to this, critical situations can be simulated, which are often not possible in running production.

5

Training courses at MULTIVAC Marking & Inspection

This know-how pays off for you!

· Current machine models, as well as older generations of machine controls, are used for training purposes. All training is tailored to teaching basic principles, operating sequences and structured fault-finding

· Modern training and presentation techniques · Small course groups - Maximum of 4 participants per course · Individual training programs to meet specific requirements · In-depth documentation

6

www.multivac.com

Page

Labelling and marking solutions CL1_v1 – MR6x5 Integrated Cross Web Labeller (Level1) 11CL2_v1 – MR6x5 Integrated Cross Web Labeller (Level2) 12CL3_v1 – MR6x5 Integrated Cross Web Labeller (TWIN) 13CL4_v1 – MR6x5 Non-Integrated Controller 14CB1_v1 – L3xx Conveyor Belt 15CB2_v1 – L3xx Conveyor Belt (Customized) 16DP1_v1 – DP2xx Direct web printer 17PR1_v1 – MULTIVAC TTO-Thermal Transfer Printer 18PR1.1_v1 – MULTIVAC TTO-Printer Layout Software 19PR1.2_v1 – MULTIVAC TTO-Printer Network Router 20PR2_v1 – Customer-Specific Printer 21

Inspection solutions IX1_v1 – I1xx X-Ray System (Level1) 22IC1_v1 – I2xx Checkweigher (Level1) 23IC2_v1 – I2xx Checkweigher (Level2) 24ICB_v1 – _connect.BRAIN 25IM1_v1 – I3xx Metal detector 26IV1_v1 – I4xx Vision-System (Level1) 27IMLC_v1 – MULTIVAC Line Control Basic 28

Contact Travel and accommodation 29Information and bookings 30

Courses

www.multivac.com© MULTIVAC 04/2018 · Subject to technical changes in line with product development · MULTIVAC is a registered trade name of MULTIVAC Sepp Haggenmüller SE & Co KG

7

10

CL1_v1 – MR6x5 Integrated Cross Web Labeller (Level1) (1 day)

For operators and service technicians

The course objectives:The objective of the training is learning to operate the cross web labeller independently and safely. The course participant will also be able to use the different types of label sensor, with emphasis on format and operator settings and recipe management.

The course contents: · Type codes · Test and measurement runs · Different label sensors · Format setting · Operator setting · Recipe management · Causes of faults

11

CL2_v1 – MR6x5 Integrated Cross Web Labeller (Level2) (1,5 days)

For operators and service technicians

Prerequisites for admissionCL1_v1 – MR6x5 Integrated Cross Web Labeller (Level1)

The course objectives:The participants will know the meaning of machine constants.They will be able to perform settings on the Terminal of the IPC Controller. The participants will also learn to independently perform software updates on the LC 140. The participants will learn how to systematically localize faults and rectify them.

The course contents: · Machine constants for the labeler · Circuit diagrams and Troubleshooting · Software update LC140

12

CL3_v1 – MR6x5 Integrated Cross Web Labeller (TWIN) (0,5 days)

For operators and service technicians

Prerequisites for admissionCL1_v1 – MR6x5 Integrated Cross Web Labeller (Level1) CL2_v1 – MR6x5 Integrated Cross Web Labeler (Level2)

The course objectives:The participant of the training is learning to operate the cross web labeler independently and safely. After the course the participant will know the different modes of the Twin labeler and how to handle them.

The course contents: · Cross web labeller with Twin option · Safety controller DINA · Operation modes · Teaching the safety controller · Format setting · Operation setting · Hardware changes

13

CL4_v1 – MR6x5 Non-Integrated Controller (depending on the training content)

For operators and service technicians

The course objectives:Setting and configuration of a labelling system witch is not controlled by IPC (ML100, LC140, LC100 ,HI000, HI208)

The course contents: · Different controllers (ML100, LC140, LC100) · Different terminals (HI000, HI208) · Test and measurement runs · Format setting · Operator setting · Job management · Job variables and machine constants

14

CB1_v1 – L3xx Conveyor Belt (2 days)

For operators and service technicians

The course objectives:The objective of the training is to be able to operate the labeler independently and safely. The Participant get to know the different versions of label dispen-sers and transport conveyors. The training includes the operation of the labeler via HMI2.0 user interface of the MULTIVAC IPC control. The participants will learn how to systematically localize faults and use the WebServer for diagnosis.

The course contents: · Mechanical construction and electrical circuitry · Different label dispenser (LD1xx/LD2xx) · Start-up and setting of the individual aggregate units: labeler, SM modules,

AC drives, label sensors etc. · Tests and causes of faults

15

CB2_v1 – L3xx Conveyor Belt (Custo-mized) (2 days)

For operators and service technicians

The course objectives:The objective of the training is to be able to operate the customer specific labeler independently and safely. The Participant get an update of their know-ledge about conveyor belt labelers, as well as they get information about start-up, configuration, and particularities of their customer conveyor belt labeler.

The course contents: · Mechanical construction and electrical circuitry of the customized L3xx · Start-up and setting of the individual aggregate units: labeler, SM modules,

AC drives, label sensors, code readers, etc. · Configuration of the customized L3xx · Tests

16

DP1_v1 – DP2xx Direct web printer (1 day)

For operators and service technicians

The course objectives:The objective of the training is to be able to operate the direct web printer independently and safely. Basic settings and job management will also be taught to the course participants. The participants will learn how to systematically localise faults.

The course contents: · Type codes · Mechanical construction and electrical circuitry · LC and IC versions · Positioning of the print · Continuous/intermittent print · Circuit diagrams

17

PR1_v1 – MULTIVAC TTO-Thermal Transfer Printer (1 day)

For operators and service technicians

The course objectives:The participant of the training is learning the basics of thermo transfer printing. The components of the TTO printer are discussed. Different settings in the HMI 2.0 are explained, as well as the fitting of spare parts.

The course contents: · Basic of thermos transfer printing · Structure of the TTO printer · Operation with HMI 2.0 · Software updates and configuration tool · Function and interfaces · Replacing of spare parts and consumable material · Optimization of the print and mechanical adjustments

18

PR1.1_v1 – MULTIVAC TTO-Printer Layout Software (0,5 days)

For operators and service technicians

Prerequisites for admissionPR1_v1 – MULTIVAC TTO-Thermal Transfer Printer

The course objectives:The participant will be able to create layouts, as well as check and print them.

The course contents: · Configuration of the software on the computer · Basic layout setting · Definition of the interface for transferring the layout to the printer · Creating different variables (date, input and graphic boxes, barcodes, etc.) · Transfer of the layout to the selected printer

19

PR1.2_v1 - MULTIVAC TTO-Printer Network Router (0,5 days)

For service technicians

Prerequisites for admissionPR1_v1 – MULTIVAC TTO-Printer

The course objectives:The course participant is able to install and configure an industrial network router (Weidmueller/mGuard)

The course contents:Following consultation and agreement, can be given on various network router modules: · Installation · Setting · Interfaces · Maintenance

20

PR2_v1 – Customer-Specific Printer (depending on the training content)

For operators and service technicians

The course objectives:The course participant can operate the printer, on which the training has been given, independently and faultlessly. He can design layouts and carry out servicing.

The course contents:Following consultation and agreement, can be given on various printer modules: · Settings · Interfaces · Print layout design · Servicing

21

IX1_v1 – I1xx X-Ray System (Level1) (3 days)

For operators and service technicians

The course objectives:The course participant gets to know the dangers and statutory provisions of operating X-ray inspection systems. Participants will learn the basics of detection of contaminated products, as well as become familiar with the independent and safe operation of an I1xx.

The course contents: · Dangers and statutory regulations of ionising radiation · Components of X-ray inspection systems · Safety circuits · Setting the search sensitivity · Teaching new products · Settings of standard filter chains

22

IC1_v1 – I2xx Checkweigher (Level1) (2 days)

For operators and service technicians

The course objectives:The course participant gets to know the construction of a checkweigher.Different selection criteria will be familiar to him.Another objective of the training is the teaching and management of different products.

The course contents: · Basic settings of the system · Teaching of products · Product management · I/O mapping · Different selection criteria

23

IC2_v1 – I2xx Checkweigher (Level2) (2 days)

For service technicians

Prerequisites for admissionIC1_v1 – I2xx Checkweigher (Level1)

The course objectives:The course participant gets to know the hardware and the exchange of electrical components. The calibration of the scale will be familiar to him.Another objective of the training are the software updates, as well as the troubleshooting.

The course contents: · Hardware I2xx · Exchange of electrical components · Software updates · Calibration of the scale · Troubleshooting

24

ICB_v1 - _connect.BRAIN (2 days)

For service technicians

Prerequisites for admissionIC1_v1 – I2xx Checkweigher (Level1)

The course objectives:The course participant gets to know the installation of the software.Server and connection settings will be familiar to him.The generation of statistic data using various interface options is also part of the training.

The course contents: · Installation of the software · Connection settings · Server settings · 2file · 2DB

25

IM1_v1 – I3xx Metal detector (1 day)

For operators and service technicians

The course objectives:The course participant gets to know the basics of detecting metal contentin products. Training will focus on independent and safe operation of metal detection equipment. Audit settings will be familiar to him.

The course contents: · Basics of detection of contaminated products · Operation · Interfaces · Teaching of products · Job management · Audit settings · Software update

26

IV1_v1 – I4xx Vision-System (Level1) (1,5 days)

For operators and service technicians

The course objectives:The participants get to know the layout and design of the visual inspection systems I 410 / I 420 demonstrated on an I410. They become familiar with various types of visual inspection.The training includes the operation via the user interface HMI 2.0 of the MULTIVAC IPC control as well as the teach-in of different products.The participants learn the basics of parameterization for various functional principles. These are: Pattern recognition, spot detection, text verification and various barcode recognitions.

The course contents: · Fundamentals of optics · Hardware and software of the I 410 / I 420 · Pattern recognition · Spot detection · Verification of text fields · Recognition of various barcodes · Recipe management

27

IMLC_v1 – MULTIVAC Line Control Basic (0,5 days)

For service technicians

Prerequisites for admissionLevel 1 training in the area of inspection

The course objectives:The course participant gets to know the software linking of a checkweigher, metal detector and/or X-Ray with a packaging machine.Different settings on the machine will be familiar to him.Another objective of the training are the machine constants of the packaging machine.

The course contents: · Machine constants of the rollstock machine · Settings on the checkweigher · Settings on the metal detector · Settings on the X-Ray · Recipe download · Line synchronisation

28

29

Travel and accommodation

Registration: Are you interested in a training course? If so, contact our Training Department as early as possible so that we can confirm your desired date. Due to high demand, there are often waiting times which you should take into account in your plans.

A training course, which has already been booked, can be cancelled on your part without charge up to 10 days before the start of the course. If a course is cancelled after the 10 day grace period, there will be a € 50 cancellation fee for each training day, per participant.

We are happy to make the hotel reservation(s) on your behalf at MULTIVAC rates in one of our partner hotels. The costs for hotel and travel are not included in the training course fee.

16 km from Enger: 7 km from Enger:

Best Western Hotel OstertorOstertor 52-54D-32105 Bad Salzuflen

Tel.: +49 (0)5222 / 98 388-0Fax: +49 (0)5222 / 98 388-100Web: www.ostertor-bestwestern.de

Parkhotel SonnenhausBorriesstraße 29D-32257 Bünde

Tel.: +49 (0)5223 / 49 113-0Fax: +49 (0)5223 / 49 113-33Web: www.parkhotel-sonnenhaus.de

30

We offer you practical training courses for your MULTIVAC labelling, marking and inspection solutions.

If you have any questions about our training courses, or would like to book a training course immediately, our colleague Martin Töniges is always available to help.

Martin Töniges

Tel.: +49 (0) 5224 / 931 203Fax: +49 (0) 5224 / 931 299E-mail: mumi-schulung@multivac.de

Information and bookings

31

www.multivac.com© MULTIVAC 04/2018 Subject to technical changes in line with product development. MULTIVAC is a registered trade name of MULTIVAC Sepp Haggenmüller SE & Co KG