Date post: | 27-Dec-2015 |
Category: |
Documents |
Upload: | deepak-thakker |
View: | 21 times |
Download: | 0 times |
CATALOGUE
P.O.Box: 8807, Dubai.Tel: 04-2853342, Fax: 04-2853347E-mail: [email protected]
Assembly and Supply of:
• Hydraulic Hoses and Fittings
• Stainless steel corrugated hoses and fittings
• Stainless steel expansion bellows
• Steel tubes, tube fittings & tube clamps
• Suction discharge, Air & Chemical hoses etc.
• Pressure guages, dowty seals, ball valves, quick release couplings etc.
Trinity Mechanical Services (Hydraulic Division)
STAINLESS STEEL EXPANSION BELLOW
Expansion control in pipelines, ducting and vessels which carry hot or cold fluids or which are exposed to the large variations in ambient temperature is a major problem confronting designers. As the metal temperature increases or decreases , the dimensional change due to thermal expansion or contraction will enduce excessive stresses in the piping , ducting or vessel and large forces will be transmitted to anchors and connected equipment. For controlling such stresses and bring them to allowable values for the materials used in piping, ducting, and vessels, several different methods are available , such as the use of pipebends and expansion loops. However the most modern designers prefer the use of metallic bellows expansion joints, because they require less space than bends and loops and because their inherent flexibility enables them to absorb movements in more than one direction , thereby permitting greater freedom in design. Furthermore , expansion joints prove to be more economical than other devices , so their use results in lower initial costs for piping and construction work, operating costs being reduced as well.
BELLOW ELEMENT.
The flexible element of an expansion joint, consisting of one or more convolutions obtained by the hydro-forming or mechanical forming according to the diameter of the shell of a material sutiable for the required specification. Bellows are welded to tube ends or flanges to constitute different models of expansion joint assemblies.
INNER SLEEVE.
A device which is also referred to as liner, telescopic sleeve etc, to avoid the head losses or turbulence and streamline the flow through bellows.It is required if the fluid flowing through the bellows is at very high velocity.
ENDS.
The ends of an expansion joint, which may be either equipped with flanges or suitably beveled for welding to adjacent equipment or piping etc.They are in compliance with applicable standards in force.Bellows offered by us are designed based on E.J.M.A guidelines and our stanadard range comprisesOf Bellows from 2inch to 72inch NB in single and multiply construction for different working temperatures , pressures and movements.The Cyclic life of a Bellow depends upon the extent to which It is stressed under optimum working Pressure, Temperature , Axial and Lateral deflection. To achieve a long life, a Bellow must be operated well within the maximum design parameters for both deflection and pressure.
AXIAL MOVEMENT.
The amount to motion parallel to the axis in a straight guided pipline.
LATERAL MOVEMENT.
A single plane deflection form the centre line of one end of the bellows but that end is keeping to remain parallel with the other end.
ANGULAR MOTION.
The ends are displaced at angle 0 to each other rather then remaining parallel.
TYPES OF EXPANSION JOINTS.
Some of the most common expansion joints being used for different applications are listed below.
AXIAL JOINTS.
This expansion joint is simply a bellows element with pipe ends or flanges connections.It is manufactured from Single and multiply elements. These bellows are suitable only for axial movements & also absorb limited lateral displacements. Tide Axial Expansion Joints also have one bellows except that their length is restrained tie rods.
UNIVERSAL EXPANSION JOINTS.
The universal expansion joint consists of two bellows separated by pipe section or spool. The primary purpose of this arrangement is to have a unit which will accept large amounts of lateral deflection. The amount of lateral deflection they can accept is a function of the amount of angulation.These joints have no restrains to resist pressure thrust like the axial. For given bellow element the amount of lateral deflection capability is increased or decreased by simply changing the length of the center spool.
Bellow expansion joints standard or custom designed are recommended for the following applications.
* Vaccum Steam * Petrochemical * Hot Water * Utilities * Solar * Environmental
Axil Movement
Lateral Movement
Angular Motion
Axil Joints
Universal Expansion Joints
Blocks
Now available with us
SAE O ñRING FLANGE CLAMPS AND BLOCK FLANGES.
We stock common range of SAE O ring split clamps and Block flange for Hydraulic Application.
* SAE O- Ring clamps and Blocks are available in different range and size.
* SAE O ñring Split Clamps
3000 PSI (61 code)
6000 PSI (62 code)
Code 61 and Code 62 SAE O ring Flange Blocks with NPT thread.
Code 61 and Code 62 SAE O ring Flange Blocks to Weld Socket.
Code 61 and Code 62 SAE Flat face flange Blocks with NPT thread.
Code 61 and Code 62 SAE Flat face flange Blocks to Weld Socket.Any other configurations are available on request.
STAINLESS STEEL CORRUGATED FLEXIBLE HOSES. HOSE Stainless Steel Corrugated flexible hoses are offered from 6mm (1/4” ) to 300mm(12”).The annular corrugated hose body provides the flexibility and pressure tight core of the assembly. BRAIDUnbraided corrugated hoses tend to elongate when pressurized above a certain level. To restrain this, an external layer of stainless steel wire braiding is provided on the hose. Braiding prevents longitudinal expansion of corrugated hose and thus increases the internal pressure strengthen of the hose many fold.Braiding is highly flexible and exactly follows the movements of the hose.To increase the pressure ratings further, two or even three layers of braiding are provided . Unless specified , braiding in high tensile stainless steel AISI 304 wire, will be supplied .
ASSEMBLIESStainless Steel hose assemblies are engineered to perfection in flexibility , strength and reliability. Hose assembly can be supplied with any types of end connections in various types of materials.The end connections are tig welded to hose.
ADVANTAGES OF FLEXIBLE METAL HOSES.• Suitableforwidetemperatuerange (-270 deg C to 700 deg C)• Compensatesforthermalexpansioncontraction in the piping system.• HighPhysicalStrength• FireResistant• MoistureResistant• LongerLife• GoodCorrosionCharacteristics• Resistanttoabrasion,penetrationanddamage• Connectsmisalignedrigidpipingabsorbsor dampens vibration and similar equipments.• Aflexibleandquickoptionforrigidpipingin difficult locations.
APPLICATIONS• CryogenicEquipment• NuclearPlants• Steam&HotWater• LubricationSystems• ChemicalIndustry• SteelIndustry• Food&BeverageIndustry• FertilizerIndustry• Sugar&PaperIndustry• AutomotiveExhaustSystems• Ships&Aircrafts• Airconditioning&RefrigerationSystems• GasBurnersystems• Compressedair&Pneumaticapplications.
P O Box 8807United Arab EmiratesE-mail : [email protected] :- 04-2853342Fax :- 04-2853347
HYDRAULICHOSES &
CONNECTORS
Uncontrolled distribution document
We reserve the right to make, without notice, changes to any drawing or data shown in this document because of technical development or other reason.Please note that all the shown compatibilities and conformities are geometrical ones, they do not necessarily imply performances compatibilites and conformities.
Catalogue
P O Box 8807, DubaiTrinity Mechanical Services (Hydraulic Division)
United Arab Emirates
Tel :- 04-2853342Fax :- 04-2853347
HYDRAULICHOSES &
CONNECTORS
Uncontrolled distribution document
We reserve the right to make, without notice, changes to any drawing or data shown in this document because of technical development or other reason.Please note that all the shown compatibilities and conformities are geometrical ones, they do not necessarily imply performances compatibilites and conformities.
Catalogue
2001
INDEX
1. HOSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. FERRULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. HOSE CONNECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. ADAPTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. STEEL TUBING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. OTHER PRODUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8. TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page No.
1-10
11-12
13-27
28
29
30
31
32-36
HYDRAULIC HOSES 2001
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR MM KG/MTR
03 3/16 5 4.8 12.7 12,000 827 3,000 207 89 0.21004 1/4 6 6.3 15.9 11,000 758 2,750 190 102 0.30005 5/16 8 7.9 17.5 10,000 690 2,500 172 114 0.35006 3/8 10 9.5 19.8 9,000 620 2,250 155 127 0.43008 1/2 12 12.7 23 8,000 552 2,000 138 178 0.53010 5/8 16 15.9 26.2 6,000 414 1,500 103 203 0.62012 3/4 20 19.1 30.2 5,000 345 1,250 86 241 0.76016 1 25 25.4 38.1 4,000 276 1,000 69 305 1.13020 1 1/4 32 31.8 46 2,500 172 625 43 419 1.42024 1 1/2 40 38.1 52.4 2,000 138 500 34 508 1.77032 2 50 50.8 66.7 1,500 103 375 26 635 2.460
Application : High pressure Hydraulic systems using mineral oils, glycols and acqueous oils
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-1 high tensile steel braid
Cover - synthetic rubber with high abrasion ozone and weather resistance
Temperature range : - 40º C to +110º C
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR MM KG/MTR
03 3/16 5 4.8 15.9 20,000 1,380 5,000 345 89 0.36004 1/4 6 6.3 17.5 20,000 1,380 5,000 345 102 0.47005 5/16 8 7.9 19.1 17,000 1,172 4,250 293 114 0.51006 3/8 10 9.5 21.4 16,000 1,103 4,000 276 127 0.63008 1/2 12 12.7 24.6 14,000 965 3,500 241 178 0.73510 5/8 16 15.9 27.8 11,000 758 2,750 190 203 0.85012 3/4 20 19.1 31.8 9,000 620 2,250 155 241 1.06016 1 25 25.4 39.7 8,000 552 2,000 138 305 1.51520 1 1/4 32 31.8 50.8 6,500 448 1,625 112 419 2.35024 1 1/2 40 38.1 57.2 5,000 345 1,250 86 508 2.70032 2 50 50.8 69.8 4,500 310 1,125 78 635 3.345
Application : High pressure Hydraulic systems using mineral oils, glycols and acqueous emulsion oils
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-2 high tensile steel braid
Cover - synthetic rubber with high abrasion ozone and weather resistance
Temperature range : - 40º C to +110º C
HYDRAULIC HOSES
SAE 100R1AT-HOSECODE
SAE 100R2AT-HOSE
HR1T
HR2T
HOSE
NOM SIZE
MIN ACTUAL
BURST PRESSURE
CODE NOM SIZE
DN
MIN ACTUAL
BURST PRESSURE
HOSE
DN
WORKING
PRESSURE
WORKING
PRESSURE
1
1
HYDRAULIC HOSES
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR PSI BAR MM KG/MTR
03 3/16 5 4.8 12 16,665 1,150 14,500 1000 3,625 250 90 0.19004 1/4 6 6.3 14 14,500 1,000 13,050 900 3,260 225 100 0.24005 5/16 8 8.0 15 13,050 900 12,325 850 3,120 215 115 0.28006 3/8 10 9.5 17.5 11,600 800 10,440 720 2,610 180 130 0.36008 1/2 12 12.7 21 9,860 680 9,280 640 2,320 160 180 0.45010 5/8 16 16.0 24 8,700 600 7,540 520 1,885 130 200 0.51012 3/4 20 19.0 28 7,250 500 6,090 420 1,525 105 240 0.65016 1 25 25.4 36 5,220 360 5,075 350 1,275 88 300 0.96020 1 1/4 32 31.8 43.5 5,075 350 3,625 250 915 63 420 1.25024 1 1/2 40 38.1 50 4,060 280 2,900 200 725 50 500 1.60032 2 50 50.8 63.5 3,625 250 2,320 160 580 40 630 2.200
Application : High pressure hydraulic systems using mineral oils, glycols and acqueous emulsion oils.
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-1 high tensile steel braid
Cover - synthetic rubber with high abrasion, ozone and weather resistance
Temperature range : - 40º C to +110º C
Special Characteristic : The impulse performance is higher than DIN-SAE specs., allowing improved and long lasting operating performances with good flexibility.
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR PSI BAR MM KG/MTR
03 3/16 5 4.8 13.7 29,000 2,000 23,925 1650 6,020 415 90 0.32004 1/4 6 6.3 15.5 25,375 1,750 23,200 1600 5,800 400 100 0.37005 5/16 8 8.0 16.5 21,460 1,480 20,300 1400 5,075 350 115 0.41206 3/8 10 9.5 19.5 20,300 1,400 19,140 1320 4,785 330 130 0.53008 1/2 12 12.7 22.5 16,965 1,170 15,950 1100 3,990 275 180 0.64010 5/8 16 16.0 25.5 14,790 1,020 14,500 1000 3,625 250 200 0.77012 3/4 20 19.0 29.5 13,050 900 12,325 850 3,120 215 240 0.96016 1 25 25.4 38 9,715 670 9,425 650 2,390 165 300 1.35020 1 1/4 32 31.8 48 8,700 600 7,250 500 1,815 125 420 2.05024 1 1/2 40 38.1 55 7,250 500 5,220 360 1,305 90 500 2.51132 2 50 50.8 67 6,090 420 4,640 320 1,160 80 630 3.160
Application : High pressure Hydraulic systems using mineral oils glycols and acqueous oils
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-2 high tensile steel braid
Cover - synthetic rubber with high abrasion ozone and weather resistance
Temperature range : - 40º C to +110º C
Special Characteristic : The impulse performance is higher than DIN-SAE spec., allowing improved and long lasting operating
performance with good flexibility
HYDRAULIC HOSES
WORKING
PRESSURE
SPEC BURST
PRESSURE
SPEC BURST
PRESSURE
WORKING
PRESSURE
SAE 100R1AT-DIN20022 1SN
HOSE
SAE 100R2AT-DIN20022 2SN
HOSE CODE
HR1T
HR2T
HOSE
HOSE
NOM SIZE
DN
MIN ACTUAL
BURST PRESSURE
CODENOM SIZE
DN
MIN ACTUAL
BURST PRESSURE
2
2001
HYDRAULIC HOSES 2001
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR PSI BAR MM KG/MTR
03 3/16 04 4.8 13.2 14,500 1,000 12,000 827 3,000 207 76 0.21004 1/4 05 6.3 15.0 13,340 920 12,000 827 3,000 207 86 0.26505 5/16 06 8.0 17.0 11,600 800 9,000 621 2,250 155 102 0.33507 13/32 07 10.5 19.5 10,875 750 8,000 552 2,000 138 117 0.39008 1/2 08 12.7 23.5 8,265 570 7,000 483 1,750 121 140 0.52510 5/8 10 16.0 27.5 7,250 500 6,000 414 1,500 103 165 0.65014 7/8 16 22.0 31.5 4,785 330 3,200 221 800 55 183 0.66018 1 1/8 20 28.0 38.0 5,220 360 2,500 172 625 43 229 0.91022 1 3/8 24 35.0 44.5 4,640 320 2,000 138 500 34 267 1.00029 1 13/16 32 46.0 56.4 3,625 250 1,400 97 350 24 337 1.480
Application : High pressure Hydraulic systems using mineral oils, glycols and acqueous emulsion oils
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-1 textile braid, 1 steel braid
Cover - a textile braid embedded with synthetic rubber
Temperature range : - 40º C to +125º C
Special Characteristic : The hose conforms to SAE 100R5 spec. and the construction makes the hose particularly suitable for tough operating conditions.
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI PSI BAR SI PSI BAR PSI MM KG/MTR
04 1/4 4 6.3 12.5 1,600 110 400 28 64 0.15005 5/16 5 8.0 14.0 1,600 110 400 28 76 0.16506 3/8 6 9.5 16.0 1,600 110 400 28 76 0.20008 1/2 8 12.7 19.8 1,600 110 400 28 102 0.26010 5/8 10 16.0 23.0 1,400 97 350 24 127 0.32012 3/4 12 19.0 26.0 1,400 97 350 24 140 0.38016 1 16 25.4 32.0 1,400 97 350 24 152 0.465
Application : Low pressure hydraulic systems using mineral oils, glycols and acqueous emulsion oils.
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-1 high tensile textile braid
Cover - synthetic rubber with high abrasion, ozone and weather resistance
Temperature range : - 40º C to +110º C
Special Characteristic : The hose conforms to SAE 100R6, the special reinforcement used makes the hose particularly reliable when operating at high pressure
and high temperature.
HYDRAULIC HOSES
SPEC BURST
PRESSURE
WORKING
PRESSURE
SPEC BURST
PRESSURE
WORKING
PRESSUREDASH
NOM SIZE
HOSE
NOM SIZE
DASH
SAE 100R5 - HOSE
SAE 100R6-HOSECODE
HR5
HR6
HOSE MIN ACTUAL
BURST PRESSURECODE
3
HYDRAULIC HOSES 2001
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR MM KG/MTR
03 3/16 03 4.8 9.7 12,000 827 3,000 207 20 0.06504 1/4 04 6.3 12.1 11,000 758 2,750 190 32 0.09805 5/16 05 8.0 14.0 10,000 689 2,500 172 45 0.11806 3/8 06 9.5 16.1 9,000 620 2,250 155 51 0.14408 1/2 08 12.7 19.4 8,000 552 2,000 138 77 0.21112 3/4 12 19.0 27 5,000 345 1,250 86 127 0.259
(Twin hoses also available)
Construction : Core - superpolyamide
Reinforcement-1 synthetic fibre braid
Cover - polyurethane
Temperature range : - 40º C to +121º C
Special Characteristic : Small outside diameter, wide fluid compatibility and lightweight.
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI PSI BAR SI PSI BAR PSI MM KG/MTR
04 1/4 04 6.3 15.8 20,000 1,379 5,000 345 51 0.17606 3/8 06 9.5 19.35 16,000 1,103 4,000 276 64 0.22008 1/2 08 12.7 22.5 14,000 965 3,500 241 102 0.283
Construction : Core - superpolyamide
Reinforcement-2 synthetic fibre braids
Cover - polyurethane
Temperature range : - 40º C to +121º C
Special Characteristic : Lightweight and compact, wide fluid compatibility
HYDRAULIC HOSES
WORKING
PRESSURE
SPEC BURST
PRESSURE
WORKING
PRESSURE
HOSE
HOSE
CODENOM SIZE DASH
SAE 100R7 - HOSE
SAE 100R8-HOSE
HR7
HR8
CODENOM SIZE
MIN ACTUAL
BURST PRESSURE
DASH
4
HYDRAULIC HOSES 2001
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR MM KG/MTR
03 3/16 03 4.75 9.40 20,000 1,379 5,000 345 75 0.10004 1/4 04 6.35 11.68 17,000 1,172 4,250 293 100 0.18506 3/8 06 9.53 15.75 13,000 896 3,250 224 125 0.24008 1/2 08 12.70 18.29 11,000 760 2,750 190 180 0.370
Construction : Core - polyester elastomer
Reinforcement-1 high tensile steel braid
Cover - polyester elastomer
Temperature range : - 40º C to +121º C
Special Characteristic : The polyester elastomer core and cover gives excellent resistance to almost all paint solvents
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR MM KG/MTR
04 1/4 04 6.35 13.72 26,000 1,792 6,500 448 100 0.30006 3/8 06 9.53 17.02 20,000 1,380 5,000 345 125 0.45008 1/2 08 12.70 21.21 16,000 1,104 4,000 276 180 0.610
Construction : Core - polyester elastomer
Reinforcement- 2 high tensile steel braids
Cover - polyester elastomer
Temperature range : - 40º C to +121º C
Special Characteristic : The polyester elastomer core and cover gives excellent resistance to almost all paint solvents
HYDRAULIC HOSES
WORKING
PRESSURE
SINGLE WIRE BRAID
THERMOPLASTIC HOSE
HTP1
HOSE
DOUBLE WIRE BRAID
THERMOPLASTIC HOSE
HOSE
CODE
WORKING
PRESSURENOM SIZE
DASH
CODE
MIN ACTUAL
BURST PRESSURE
MIN ACTUAL
BURST PRESSURENOM SIZE
DASH
5
HTP2
HYDRAULIC HOSES 2001
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR PSI BAR MM KG/MTR
04 1/4 6 6.3 17.8 34,800 2,400 26,100 1,800 6,525 450 150 0.62006 3/8 10 9.5 21.4 30,450 2,100 25,810 1,780 6,450 445 180 0.77008 1/2 12 12.7 24.6 27,550 1,900 24,070 1,660 6,020 415 230 0.92010 5/8 16 16.0 28.5 23,200 1,600 20,300 1,400 5,075 350 250 1.12012 3/4 20 19.0 32.0 23,000 1,600 20,300 1,400 5,075 350 300 1.56016 1 25 25.4 39.7 21,750 1,500 16,240 1,120 4,060 280 340 2.06020 1 1/4 32 31.8 50.8 18,125 1,250 12,180 840 3,045 210 457 3.31024 1 1/2 40 38.1 57.0 14,500 1,000 10,730 740 2,685 185 559 3.81032 2 50 50.8 70.6 14,500 1,000 9,570 660 2,395 165 660 5.350
Application : Very high pressure hydraulic systems using hydraulic oils
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-4 high tensile steel spirals
Cover - synthetic rubber with high temperature, ozone and abrasion resistance
Temperature range : - 40º C to +121º C
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR PSI BAR MM KG/MTR
16 1 25 25.4 39.2 23,925 1,650 20,000 1,379 5,000 345 305 2.28020 1 1/4 32 32.0 49.8 21,025 1,450 20,000 1,379 5,000 345 419 3.71024 1 1/2 40 38.0 57.3 21,750 1,500 20,000 1,379 5,000 345 508 4.96032 2 50 50.8 71.0 20,300 1,400 20,000 1,379 5,000 345 635 7.360
Application : Very high pressure hydraulic systems using hydraulic oils
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-4 high tensile steel spirals upto 1" bore, and six spirals from 1 1/4" bore and above
Cover - synthetic rubber with high temperature, ozone and abrasion resistance
Temperature range : - 40º C to +121º C
HYDRAULIC HOSES
SAE 100R9R - DIN 20023 4SP HOSE
HR9R
HR13
HOSE
SAE 100R13 HOSE HOSE
CODE
CODENOM SIZE
DN
SPEC BURST
PRESSURE
MIN ACTUAL
BURST PRESSURENOM SIZE
DN
MIN ACTUAL
BURST PRESSURE
WORKING
PRESSURE
SPEC BURST
PRESSURE
WORKING
PRESSURE
6
HYDRAULIC HOSES 2001
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR PSI BAR MM KG/MTR
16 1 25 25.4 38.0 25,375 1,750 22,040 1,520 5,510 380 340 2.08020 1 1/4 32 31.8 45.2 20,300 1,400 18,850 1,300 4,715 325 460 2.51024 1 1/2 40 38.1 53.5 17,400 1,200 16,820 1,160 4,205 290 560 3.42032 2 50 50.8 68.0 15,950 1,110 14,500 1,000 3,625 250 700 4.730
Application : Very high pressure hydraulic systems using hydraulic oils
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-4 high tensile steel spirals
Cover - synthetic rubber with high temperature, ozone and abrasion resistance
Temperature range : - 40º C to +121º C
MIN ACTUAL
BURST PRESSURE
SPEC BURST
PRESSURE
WORKING
PRESSURE
DIN 20023 4SH HOSE
H4SH
HOSE
CODENOM SIZE DN
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR MM KG/MTR
04 1/4 6 6.35 17.80 36,250 2,500 14,500 1,000 150 0.6006 3/8 10 9.50 23.80 36,250 2,500 14,500 1,000 200 1.1408 1/2 12 12.70 23.10 36,250 2,500 14,500 1,000 240 1.3412 3/4 20 19.05 32.20 36,250 2,500 14,500 1,000 305 2.51
Construction : Tube - water and Oil resistant synthetic rubber
Reinforcement-4 high tensile steel spirals
Cover - synthetic rubber with high temperature, ozone and abrasion resistance
Temperature range : -40º C to +100º C
HYDRAULIC HOSES
PRESSURE
WORKING
PRESSURECODENOM SIZE
WATER BLAST HOSE
DN
HOSE SPEC BURST
HRWB
7
HYDRAULIC HOSES 2001
HOSES
MAX. WORKING MIN BEND WEIGHT
PRESSURE AT 20 C PRESSURE AT 20 C RADIUS APPROX
in mm MIN MAX PSI MIN MAX PSI BAR PSI BAR MM KG/MTR
02 1/8 3.5 3.4 3.70 5.9 6.3 4,205 290 12,615 870 22 0.06503 3/16 4.5 4.4 4.75 6.9 7.3 3,845 265 11,530 795 40 0.08004 1/4 6.3 6.0 6.50 8.3 8.7 3,480 240 10,440 720 60 0.09305 5/16 8.0 7.5 8.00 9.8 10.3 2,900 200 8,700 600 70 0.11006 3/8 9.5 9.1 9.60 11.5 12.0 2,755 190 8,265 570 80 0.12408 1/2 12.7 11.9 12.80 14.5 15.4 2,175 150 6,525 450 110 0.20710 5/8 16.0 15.0 16.00 17.8 18.9 1,595 110 4,785 330 150 0.25512 3/4 19.0 18.0 19.20 21.0 22.3 1,160 80 3,480 240 200 0.31516 1 25.4 24.0 25.40 27.6 28.7 800 55 2,400 165 300 0.430
Construction The hose has a smooth innercore of extruded white Teflon with a single 304 stainless steel wire braid reinforcement
Temperature range -54º C to +232º C for continuous service
-73º C to +260º C for intermittent service
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR PSI BAR MM KG/MTR
06 3/8 10 9.5 20.0 23,200 1,600 16,000 1,103 4,000 276 127 0.62008 1/2 12 12.7 23.8 19,575 1,350 16,000 1,103 4,000 276 178 0.80012 3/4 20 19.0 30.7 20,300 1,400 16,000 1,103 4,000 276 241 1.22016 1 25 25.4 38.0 21,025 1,450 16,000 1,103 4,000 276 305 2.05020 1 1/4 32 31.8 47.0 17,400 1,200 12,000 827 3,000 207 419 2.810024 1 1/2 40 38.1 53.5 11,600 800 10,000 690 2,500 172 508 3.32032 2 50 50.8 66.7 11,600 800 10,000 690 2,500 172 635 4.620
Application : Very high pressure hydraulic systems using hydraulic oils
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-4 high tensile steel spirals
Cover - synthetic rubber with high temperature, ozone and abrasion resistance
Temperature range : - 40º C to +121º C
Special Characteristic : The hose exceeds SAE 100R12 spec., particularly on the impulse and burst pressures.
HYDRAULIC HOSES
BORE SIZE iNTERNAL DIA
HOSE
OUTSIDE DIA
MM MMCODE
HSST
SAE 100 R12 HOSECODE
HR12
NOM SIZE
DN
MIN ACTUAL
BURST PRESSURE
MIN BURST
SPEC BURST
PRESSURE
WORKING
PRESSURE
P.T.F.E hose has outstanding properties which are unmatched by any other flexible hose. It is possible to greatly reduce (or completely eliminate) maintenance and replacement costs which occur with conventional hoses used in extremely adverse conditions on various industrial applications. Within its working temperature range P.T.F.E. is completely inert to most known chemicals including alcohols, ehtylene glycol, concentrated acids, oils and fuels. P.T.F.E. hose has been tested and recommended for such aggressive acids, gases and solvents as nitrogen, hydrogen, ammonia, freons, butane, propane, chlorine, benzene, toluene, xylene, carbon tetrachloride, trichlorethylene, esters, ketones, hot fuming nitric, sulphuric and hydrochloric acid, concenrated sodium hydroxide, ammonia hydroxide and steam. Exceptions are few and comprise molten alkali metals and elementary flourine at elevated temperatures and pressures. P.T.F.E. will not cause contamination and can be handled with complete safety within its working temperature limits.
8
STAINLESS STEELTEFLON HOSE
HYDRAULIC HOSES 2001
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR PSI BAR MM KG/MTR
04 1/4 6 6.3 16.0 14,500 1,000 13,050 900 3,335 230 100 0.32005 5/16 8 8.0 17.5 12,835 885 12,325 850 3,045 210 114 0.34506 3/8 10 9.5 20.0 11,385 785 10,440 720 3,045 210 127 0.44508 1/2 12 12.7 21.0 9,860 680 9,280 640 2,320 160 178 0.540
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-1 high tensile steel braid
Cover - synthetic rubber with high abrasion, ozone and weather resistance
Temperature range : - 40º C to +150º C
HOSES
MIN BEND WEIGHT
ID OD RADIUS APPROX
MM MM PSI BAR PSI BAR PSI BAR MM KG/MTR
05 5/16 8 8.0 19.0 21,315 1,470 20,300 1400 5,800 400 114 0.51006 3/8 10 9.5 21.5 19,575 1,350 19,140 1320 5,800 400 127 0.63008 1/2 12 12.7 24.5 16,675 1,150 15,950 1100 4,060 280 178 0.775
Construction : Tube - Oil resistant synthetic rubber
Reinforcement-2 high tensile steel braid
Cover - synthetic rubber with high abrasion, ozone and weather resistance
Temperature range : - 40º C to +150º C
HYDRAULIC HOSES
BURST PRESSURE
SPEC BURST
PRESSURE
WORKING
PRESSURENOM SIZE
DASH
MIN ACTUAL SPEC BURST
PRESSUREBURST PRESSURE
WORKING
PRESSURE
MIN ACTUAL
SINGLE WIRE BRAID JETWASH
HOSE
R1A-SH
R2A-SH
HOSE
DOUBLE WIRE BRAID JETWASH
HOSE
HOSE
CODENOM SIZE
DIN
CODE
9
HYDRAULIC HOSES 2001
HOSES
WEIGHT
STATIC FLEXING PRESSURE AT 20º C APPROX
MM IN MM IN PSI MM MM BAR PSI BAR PSI KG/MTR
04 6.3 1/4 14.4 0.567 25 100 142 2,060 568 8,240 0.2906 9.5 3/8 19.4 0.763 40 150 104 1,510 416 6,040 0.4308 12.7 1/2 23.4 0.922 50 150 92 1,325 366 5,300 0.5312 19.0 3/4 29.6 1.170 70 200 70 1,010 278 4,040 0.7516 25.4 1 37.1 1.460 90 200 71 1,025 282 4,100 1.0020 31.8 1 1/4 48.5 1.910 108 250 45 653 180 2,610 1.3024 38.1 1 1/2 56.6 2.230 127 250 41 595 164 2,380 1.7032 50.8 2 67.8 2.670 175 350 31 440 122 1,760 1.9040 63.5 2 1/2 87.6 3.450 200 410 26 370 102 1,480 2.8048 76.2 3 99.8 3.930 200 450 19 280 76 1,120 3.3064 101.6 4 129.0 5.080 230 560 18 267 73 1,068 4.6096 152.4 6 180.0 7.100 320 815 11 162 45 648 7.70
Construction : Butt welded annular corrugated flexible stainless steel (type 316L and 321) tubing with a single stainless steel wire braid.
Temperature range : -200º C to +600º C (type 316L +420º C)
HOSES
WEIGHT
STATIC FLEXING PRESSURE AT 20º C PRESSURE AT 20º C APPROX
MM IN MM IN MM MM BAR PSI BAR PSI KG/MTR
04 6.3 1/4 15.8 0.622 25 100 255 3,700 1,020 14,800 0.3906 9.5 3/8 21.0 0.826 40 150 187 2,710 748 10,480 0.5908 12.7 1/2 25.0 0.985 50 150 165 2,400 660 9,600 0.7312 19.0 3/4 31.2 1.230 70 200 125 1,810 500 7,240 1.1016 25.4 1 39.2 1.540 90 200 120 1,740 480 6,960 1.5020 31.8 1 1/4 50.6 1.990 108 250 80 1,160 320 4,640 1.9024 38.1 1 1/2 58.7 2.310 127 250 71 1,030 284 4,120 2.4032 50.8 2 69.9 2.750 175 350 50 725 200 2,900 2.6040 63.5 2 1/2 89.7 3.530 200 410 46 667 184 2,668 3.8048 76.2 3 102.0 4.010 200 450 34 493 136 1,972 4.4064 101.6 4 132.0 5.180 230 560 33 480 132 1,920 6.4096 152.4 6 183.0 7.200 320 815 20 290 80 1,160 9.90
Construction : Butt welded annular corrugated flexible stainless steel (type 316L and 321) tubing with a double stainless steel wire braid.
Temperature range : -200º C to +600º C (type 316L +420º C)
HYDRAULIC HOSES
MIN BURST
MIN BURSTMAX. WORKING
MAX. WORKING
PRESSURE AT 20º C
MIN BEND RADIUS
DIAMETERCODE
HSPF2
NOMINAL ID MAX HOSE OD
Hoses are designed to withstand extremes of operating temperatures under arduous conditions. Flexibility is excellent and this tubing will workunder conditions where extreme vibration is encountered,minimum bend radii are very low and the tubing is non-magnetic. The hose is suitablefor exhaust and corrosive fluids, steam, acids and solvents, radioactive gases and fluids, chemical gases, petrol and many alkalis, acids, etc.
SINGLE WIRE BRAID STAINLESS
STEEL CONVOLUTED
HOSE
HSPF1
DOUBLE WIRE BRAID STAINLESS
STEEL CONVOLUTED
HOSE
NOMINAL ID
CODE
MAX HOSE OD
DIAMETER
MIN BEND RADIUS
10
HOSE CONNECTORS 2001
FERRULES
Hose I.D. Dimensions(mm)
DN mm SIZE Inch D L
O3 5 4.8 03 3/16" 19 26
O4 6 6.3 04 1/4" 20 30.5
O5 8 7.9 05 5/16" 22 30.5
O6 10 9.5 06 3/8" 24 31.5
O8 12 12.7 08 1/2" 28.5 34
10 16 15.9 10 5/8" 32 37
12 20 19.1 12 3/4" 36 42.5
16 25 25.4 16 1" 43 50
20 32 31.8 20 1 1/4" 53 59
Hose I.D. Dimensions(mm)
DN mm SIZE Inch D L
HSN2 O4 6 6.3 04 1/4" 22 30.5
O5 8 7.9 05 5/16" 24 30.5
O6 10 9.5 06 3/8" 25.5 31.5
O8 12 12.7 08 1/2" 30 34
10 16 15.9 10 5/8" 34 37
12 20 19.1 12 3/4" 38 42.5
16 25 25.4 16 1" 46 50
Hose I.D. Dimensions(mm)
DN mm SIZE Inch D L
HSP1 O3 5 4.8 03 3/16" 14 27
O4 6 6.3 04 1/4" 17 29
O5 8 7.9 05 5/16" 19 30
O6 10 9.5 06 3/8" 21 31
O8 12 12.7 08 1/2" 25.5 34
10 16 15.9 10 5/8" 28.5 36
12 20 19.1 12 3/4" 32 42
16 25 25.4 16 1" 40 50
HOSE CONNECTORS
1 WIRE FERRULES CODE
HSN1
2 WIRE FERRULES CODE
R7 FERRULES CODE
11
HOSE CONNECTORS 2001
Hose I.D. Dimensions(mm)
DN mm SIZE Inch D L
O4 6 6.3 04 1/4" 22 30
O6 10 9.5 06 3/8" 25.5 33.5
O8 12 12.7 08 1/2" 30 37
10 16 15.9 10 5/8" 34 40
12 20 19.1 12 3/4" 38 43
16 25 25.4 16 1" 46 60
20 32 31.8 20 1 1/4" 56 66
24 40 38.1 24 1 1/2" 65 76.5
32 50 50.8 32 2" 80 80
Hose I.D. Dimensions(mm)
DN mm SIZE Inch D L
16 25 25.4 16 1" 46 75
20 32 31.8 20 1 1/4" 60 88
24 40 38.1 24 1 1/2" 67 94
32 50 50.8 32 2" 84.5 99
HOSE CONNECTORS
HEH
HMS
CODE4 WIRE FERRULES
6 WIRE EXTRA HIGH PRESSURE FERRULES
CODE
12
HOSE CONNECTORS 2001
HA10 B.S.P. MALE PARALLEL - 60° CONE SEAT
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L S
O4 6 6.30 04 1/4" 1/4"-19 26.0 54.5 19
O6 10 9.50 06 3/8" 3/8"-19 28.5 59.0 22
O8 12 12.70 08 1/2" 1/2"-14 33.0 66.0 27
10 16 15.90 10 5/8" 5/8"-14 35.0 71.0 30
12 20 19.10 12 3/4" 3/4"-14 39.0 80.0 32
16 25 25.40 16 1" 1"-11 43.5 98.5 41
20 32 31.80 20 1 1/4" 1 1/4"-11 47.0 108.0 50
24 40 38.10 24 1 1/2" 1 1/2"-11 51.0 121.5 55
32 50 50.80 32 2" 2"-11 53.5 129.5 70
HA22 B.S.P. TAPER MALE - 60° CONE SEAT
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L S
O4 6 6.3 04 1/4" 1/4"-19 26.7 55.2 15
O6 10 9.5 06 3/8" 3/8"-19 27.8 58.3 19
O8 12 12.7 08 1/2" 1/2"-14 34.5 67.5 22
12 20 19.1 12 3/4" 3/4"-14 37.2 78.2 27
16 25 25.4 16 1" 1"-11 44.0 99.0 36
20 32 31.8 20 1 1/4" 1 1/4"-11 48.1 109.1 46
24 40 38.1 24 1 1/2" 1 1/2"-11 49.9 120.4 50
32 50 50.8 32 2" 2"-11 55.2 131.2 65
HA17 B.S.P. FEMALE - 60° CONE
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L G S
O4 6 6.3 04 1/4" 1/4"-19 18.7 47.2 4.1 19
O6 10 9.5 06 3/8" 3/8"-19 19.7 50.2 5.8 22
O8 12 12.7 08 1/2" 1/2"-14 22.7 55.7 6.5 27
10 16 15.9 10 5/8" 5/8"-14 22.7 58.7 9.3 30
12 20 19.1 12 3/4" 3/4"-14 26.1 67.1 8.6 32
16 25 25.4 16 1" 1"-11 29.8 84.8 10.5 41
20 32 31.8 20 1 1/4" 1 1/4"-11 32.9 93.9 10.0 50
24 40 38.1 24 1 1/2" 1 1/2"-11 36.0 12.0 55
32 50 50.8 32 2" 2"-11 37.0
106.5
113.0 16.0 70
HOSE CONNECTORS
BSP FEMALE STANDARD CODE
CODE
CODE
BSP MALE PARALLEL
BSPT MALE
13
HOSE CONNECTORS 2001
HB1790° B.S.P. COMPACT ELBOW - 60° CONE
SOLID - CRIMPED NUT
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L K G S S1
O4 6 6.3 04 1/4" 1/4"-19 18.5 47.0 22.0 4.1 19.0 14.0
O6 10 9.5 06 3/8" 3/8"-19 20.0 50.5 24.5 5.8 22.0 17.0
O8 12 12.7 08 1/2" 1/2"-14 24.0 57.0 29.0 6.5 27.0 22.0
HG17 B.S.P. 90° SWEPT ELBOW - 60° CONE - SOLID
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L K G S
O4 6 6.3 04 1/4" 1/4"-19 24.0 52.0 28.0 4.1 19.0
O6 10 9.5 06 3/8" 3/8"-19 34.0 64.0 36.5 5.8 22.0
O8 12 12.7 08 1/2" 1/2"-14 41.0 74.0 44.0 6.5 27.0
10 16 15.9 10 5/8" 5/8"-14 49.0 85.0 50.5 9.3 30.0
12 20 19.1 12 3/4" 3/4"-14 58.0 99.0 60.5 8.6 32.0
16 25 25.4 16 1" 1"-11 74.0 129.0 72.5 10.5 41.0
20 32 31.8 20 1 1/4" 1 1/4"-11 72.0 153.0 89.0 10.0 50.0
24 40 38.1 24 1 1/2" 1 1/2"-11 108.0 179.0 101.5 12.0 55.0
32 50 50.8 32 2" 2"-11 142.0 218.0 217.5 16.0 70.0
HJ17 B.S.P. 45° SWEPT ELBOW - 60° CONE - SOLID
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L K G S S1
O4 6 6.3 04 1/4" 1/4"-19 40.0 68.5 16.5 4.1 19.0
O6 10 9.5 06 3/8" 3/8"-19 53.5 84.0 19.5 5.8 22.0
O8 12 12.7 08 1/2" 1/2"-14 64.0 97.0 24.5 6.5 27.0
10 16 15.9 10 5/8" 5/8"-14 78.5 114.5 26.0 9.3 30.0
12 20 19.1 12 3/4" 3/4"-14 88.5 129.5 35.0 8.6 32.0
16 25 25.4 16 1" 1"-11 110.0 165.0 42.0 10.5 41.0
20 32 31.8 20 1 1/4" 1 1/4"-11 138.0 199.0 54.5 10.0 50.0
24 40 38.1 24 1 1/2" 1 1/2"-11 162.0 232.5 58.5 12.0 55.0
32 50 50.8 32 2" 2"-11 205.5 281.5 66.5 16.0 70.0
HOSE CONNECTORS
CODE
BSPF 45 DEG STANDARD
CODE
BSPF 90 DEG COMPACT
BSPF 90 DEG STANDARD
CODE
14
HOSE CONNECTORS 2001
HA19B.S.P. FEMALE - FLAT FACE
PRESSED NUT
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L G S
O4 6 6.3 04 1/4" 1/4"-19 15.5 44 7 19
06 10 9.5 06 3/8" 3/8"-19 16.5 47 9 22
O8 12 12.7 08 1/2" 1/2"-14 19.2 52.2 10 27
10 16 15.9 10 5/8" 5/8"-14 20.5 56.5 11.5 30
12 20 19.1 12 3/4" 3/4"-14 22.7 63.7 12 32
16 25 25.4 16 1" 1"-11 26.3 81.3 14 41
HA34 N.P.T.F. MALE - 60° CONE SEAT
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L S
O4 6 6.3 04 1/4" 1/4"-18 26.5 55 15
O6 10 9.5 06 3/8" 3/8"-18 27.5 58 19
O8 12 12.7 08 1/2" 1/2"-14 34.5 67.5 22
12 20 19.1 12 3/4" 3/4"-14 37.2 78.2 27
16 25 25.4 16 1" 1"-11,5 43.5 98.5 36
20 32 31.8 20 1 1/4" 1 1/4"-11,5 46.1 107 46
24 40 38.1 24 1 1/2" 1 1/2"-11,5 54 112 53
32 50 50.8 32 2" 2"-11,5 57 130 65
HOSE CONNECTORS
CODE
BSPF FLAT FACE
NPT MALE STANDARD
CODE
15
HOSE CONNECTORS 2001
HA38STRAIGHT SAE J518 FLANGE - 3000 PSI
SOLID
Hose I.D. Dimensions(mm)
DN mm SIZE Inch H L A
O8 12 12.7 08 1/2" 1/2" 48.5 81.5 30.2
12 20 19.1 12 3/4" 3/4" 53.5 94.5 38.1
16 25 25.4 16 1" 1" 60.5 115.5 44.5
20 32 31.8 20 1 1/4" 1 1/4" 65.5 126.5 50.8
24 40 38.1 24 1 1/2" 1 1/2" 70.5 141.0 60.3
32 50 50.8 32 2" 2" 77.0 153.0 71.4
STRAIGHT KOMATSU FLANGE - SOLID
10 16 15.9 10 5/8" 5/8" 49.3 85.3 34
HG3890° SAE J518 FLANGE - 3000 PSI
SOLID
Hose I.D. Dimensions(mm)
DN mm SIZE Inch H L K A
O8 12 12.7 08 1/2" 1/2" 41 74 42 30.2
12 20 19.1 12 3/4" 3/4" 58 99 57 38.1
16 25 25.4 16 1" 1" 74 129 69 44.5
20 32 31.8 20 1 1/4" 1 1/4" 92 153 87 50.8
24 40 38.1 24 1 1/2" 1 1/2" 108 179 101 60.3
32 50 50.8 32 2" 2" 142 218 134 71.4
90° KOMATSU FLANGE - SOLID
10 16 15.9 10 5/8" 5/8" 49 85 49 34
HOSE CONNECTORS
FLANGE
FLANGE
SAE FLANGE 3000 PSI 90 DEG STANDARD CODE
SAE FLANGE 3000PSI STANDARD
CODE
16
HOSE CONNECTORS 2001
HJ3845° SAE J518 FLANGE - 3000 PSI
ONE PIECE
Hose I.D. Dimensions(mm)
DN mm SIZE Inch H L K A
O8 12 12.7 08 1/2" 1/2" 62.0 95 22.5 30.2
12 20 19.1 12 3/4" 3/4" 86.5 128 33 38.1
16 25 25.4 16 1" 1" 107.5 163 39.5 44.5
20 32 31.8 20 1 1/4" 1 1/4" 136.5 198 53 50.8
24 40 38.1 24 1 1/2" 1 1/2" 162.0 233 58.5 60.3
32 50 50.8 32 2" 2" 210.5 287 71.5 71.4
HZF38SAE J518 SPLIT FLANGE HALF
3000 PSI
Dimensions(mm)
B D E F I
O8 23.8 9 9.15 15.9 22.2
12 30.2 11 11.90 19 28.6
16 34.9 13 13.90 22.2 36.5
20 38.9 15 15.80 23.8 39.7
24 47.6 17 18.20 27 46
32 57.1 21 22.20 36.5 55.6
HOSE CONNECTORS
1 1/2"
2"
1/2"
3/4"
1"
1 1/4"
112.7 69.9
133.3 77.8
80.9 52.4
95.2 58.7
FLANGE
SPLIT FLANGE 3000PSI
CODE
SAE FLANGE 45 DEG 3000 PSI
CODE
FLANGE
C
56.3
71.4 47.6
A
17
38.1
HOSE CONNECTORS 2001
HA39STRAIGHT SAE J518 FLANGE - 6000 PSI
ONE PIECE
Hose I.D. Dimensions(mm)
DN mm SIZE Inch H L A
O8 12 12.7 08 1/2" 1/2" 49.5 82.5 31.7
12 20 19.1 12 3/4" 3/4" 60.0 101.0 41.3
16 25 25.4 16 1" 1" 66.5 121.5 47.6
20 32 31.8 20 1 1/4" 1 1/4" 71.0 132.0 54.0
24 40 38.1 24 1 1/2" 1 1/2" 81.0 151.5 63.5
32 50 50.8 32 2" 2" 100.0 176.0 79.4
HG3990° SAE J518 FLANGE - 6000 PSI
ONE PIECE
Hose I.D. Dimensions(mm)
DN mm SIZE Inch H L K A
O8 12 12.7 08 1/2" 1/2" 41 74 42 31.7
12 20 19.1 12 3/4" 3/4" 58 99 62 41.3
16 25 25.4 16 1" 1" 74 129 75 47.6
20 32 31.8 20 1 1/4" 1 1/4" 92 153 90 54.0
24 40 38.1 24 1 1/2" 1 1/2" 108 179 102 63.5
32 50 50.8 32 2" 2" 142 218 137 79.4
HOSE CONNECTORS
FLANGE
FLANGE
SAE FLANGE 90 DEG 6000 PSI STANDARD CODE
SAE FLANGE 6000 PSI STANDARD
CODE
18
HOSE CONNECTORS 2001
HJ3945° SAE J518 FLANGE - 6000 PSI
ONE PIECE
Hose I.D. Dimensions(mm)
DN mm SIZE Inch H L K A
O8 12 12.7 08 1/2" 1/2" 63.0 96.0 23.5 31.7
12 20 19.1 12 3/4" 3/4" 89.5 130.5 36.0 41.3
16 25 25.4 16 1" 1" 112.0 167.0 44.0 47.6
20 32 31.8 20 1 1/4" 1 1/4" 138.5 200.0 55.0 54.0
24 40 38.1 24 1 1/2" 1 1/2" 162.5 233.0 58.5 63.5
12 20 19.1 12 3/4" 3/4" 89.5 130.5 36.0 41.3
32 50 50.8 32 2" 2" 212.5 289.0 73.5 79.4
HZF39SAE J518 SPLIT FLANGE HALF
6000 PSI
Dimensions(mm)
B D E F I
O8 23.8 9 9.2 15.9 22.2
12 30.2 11 11.9 19.0 28.6
16 34.9 13 13.9 22.2 36.5
20 38.9 15 15.8 23.8 39.7
24 47.6 17 18.2 27.0 46.0
32 57.1 21 22.2 36.5 55.6
HOSE CONNECTORS
C
56.3 40.5
71.4 50.8
80.9 57.1
95.2 66.7
FLANGE
SAE SPLIT FLANGE 6000 PSI
CODE
SAE FLANGE 6000 PSI 45 DEG STANDARD CODE
A
FLANGE
112.7 79.4
133.3 96.8
1/2"
3/4"
1"
1 1/4"
1 1/2"
2"
19
HOSE CONNECTORS 2001
HA50 J.I.C. MALE - 74° CONE
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L S
O4 6 6.30 04 1/4" 7/16"-20 26.5 55.0 12.0
O5 8 7.90 05 5/16" 1/2"-20 26.5 55.0 14.0
O6 10 9.50 06 3/8" 9/16"-18 26.5 57.0 15.0
O8 12 12.70 08 1/2" 3/4"-16 28.7 61.7 19.0
10 16 15.90 10 5/8" 7/8"-14 34.7 70.7 24.0
12 20 19.10 12 3/4" 1 1/16"-12 40.4 81.4 27.0
16 25 25.40 16 1" 1 5/16"-12 42.7 97.7 36.0
20 32 31.80 20 1 1/4" 1 5/8"-12 46.5 107.5 46.0
24 40 38.10 24 1 1/2" 1 7/8"-12 51.2 121.7 50.0
32 50 50.80 32 2" 2 1/2"-12 62.2 138.2 65.0
HA53 J.I.C. FEMALE - 74° CONE
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L S
O4 6 6.3 04 1/4" 7/16"-20 14.7 43.2 15.0
O5 8 7.9 05 5/16" 1/2"-20 16.0 44.5 17.0
O6 10 9.5 06 3/8" 9/16"-18 16.0 46.5 19.0
O8 12 12.7 08 1/2" 3/4"-16 20.0 53.0 24.0
10 16 15.9 10 5/8" 7/8"-14 21.5 57.5 27.0
12 20 19.1 12 3/4" 1 1/16"-12 24.0 65.0 32.0
16 25 25.4 16 1" 1 5/16"-12 26.0 81.0 41.0
20 32 31.8 20 1 1/4" 1 5/8"-12 27.8 88.8 50.0
24 40 38.1 2'4 1 1/2" 1 7/8"-12 31.5 102.0 55.0
32 50 50.8 32 2" 2 1/2"-12 33.5 109.5 70.0
HOSE CONNECTORS
CODE
JIC MALE STANDARD
JIC FEMALE STANDARD
CODE
20
HOSE CONNECTORS 2001
HG53 J.I.C. 90° SWEPT ELBOW - 74° CONE SEATSOLID - PRESSED NUT
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L K S
O4 6 6.3 04 1/4" 7/16"-20 24 52 24 15
O5 8 7.9 05 5/16" 1/2"-20 31 59 29 17
O6 10 9.5 06 3/8" 9/16"-18 34 64 33 19
O8 12 12.7 08 1/2" 3/4"-16 41 74 41 24
10 16 15.9 10 5/8" 7/8"-14 49 85 49 27
12 20 19.1 12 3/4" 1 1/16"-12 58 99 59 32
16 25 25.4 16 1" 1 5/16"-12 74 129 72 41
20 32 31.8 20 1 1/4" 1 5/8"-12 92 153 87 50
24 40 38.1 2'4 1 1/2" 1 7/8"-12 108 179 100 55
32 50 50.8 32 2" 2 1/2"-12 142 218 126 70
HJ53 J.I.C. 45° SWEPT ELBOW - 74° CONE SEATSOLID - PRESSED NUT
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L K S
O4 6 6.3 04 1/4" 7/16"-20 37.0 66.0 13.5 15.0
O5 8 7.9 05 5/16" 1/2"-20 46.0 74.5 16.0 17.0
O6 10 9.5 06 3/8" 9/16"-18 51.0 81.0 17.0 19.0
O8 12 12.7 08 1/2" 3/4"-16 62.0 98.0 22.5 24.0
10 16 15.9 10 5/8" 7/8"-14 77.0 113.0 25.0 27.0
12 20 19.1 12 3/4" 1 1/16"-12 86.0 127.0 33.0 32.0
16 25 25.4 16 1" 1 5/16"-12 107.5 162.5 40.0 41.0
20 32 31.8 20 1 1/4" 1 5/8"-12 135.5 196.5 52.0 50.0
24 40 38.1 24 1 1/2" 1 7/8"-12 161.0 231.0 57.0 55.0
32 50 50.8 32 2" 2 1/2"-12 205.5 281.0 66.5 70.0
HOSE CONNECTORS
CODE
CODE
JIC FEMALE 90 DEG STANDARD
JIC FEMALE 45 DEG
21
HOSE CONNECTORS 2001
HA65METRIC MALE - 24° CONE SEAT
LIGHT TYPE
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L E S
O4 6 6.30 04 1/4" M12x1,5 23 52 6 14
O4 6 6.30 04 1/4" M14x1,5 23 52 8 14
O5 8 7.90 05 5/16" M16x1,5 24 53 10 17
O6 10 9.50 06 3/8" M16x1,5 24 55 10 17
O6 10 9.50 06 3/8" M18x1,5 24 55 12 19
O8 12 12.70 08 1/2" M22x1,5 29 62 15 24
10 16 15.90 10 5/8" M26x1,5 29 65 18 27
12 20 19.10 12 3/4" M30x2 32 73 22 32
16 25 25.40 16 1" M36x2 33 88 28 36
20 32 31.80 20 1 1/4" M45x2 38 99 35 46
24 40 38.10 24 1 1/2" M52x2 41 111 42 55
HA68METRIC MALE - 24° CONE SEAT
HEAVY TYPE
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L E S
O4 6 6.3 04 1/4" M16x1,5 25 54 8 17
O4 6 6.3 04 1/4" M18x1,5 26 55 10 19
O6 10 9.5 06 3/8" M20x1,5 27 58 12 22
O6 10 9.5 06 3/8" M22X1,5 29 60 14 24
O8 12 12.7 08 1/2" M24x1,5 31 64 16 27
10 16 15.9 10 5/8" M30x2 33 69 20 32
12 20 19.1 12 3/4" M36x2 36 77 25 36
16 25 25.4 16 1" M42x2 41 96 30 46
20 32 31.8 20 1 1/4" M52x2 46 107 38 55
HOSE CONNECTORS
CODE
CODE
METRIC MALE (LIGHT)STANDARD
METRIC MALE (HEAVY)
STANDARD
22
HOSE CONNECTORS 2001
HA67O'RING METRIC FEMALE - 24° CONE
LOOSE NUT - LIGHT TYPE
Hose I.D. Thread Tube Dimensions(mm)
DN mm SIZE Inch F mm H L S
O4 6 6.3 04 1/4" M12x1,5 6 23 52 17
O4 6 6.3 04 1/4" M14x1,5 8 24 53 17
O5 8 7.9 05 5/16" M16x1,5 10 25 54 19
O6 10 9.5 06 3/8" M16x1,5 10 25 56 19
O6 10 9.5 06 3/8" M18x1,5 12 25 56 22
O8 12 12.7 08 1/2" M22x1,5 15 27 60 27
10 16 15.9 10 5/8" M26x1,5 18 28 64 32
12 20 19.1 12 3/4" M30x2 22 31 72 36
16 25 25.4 16 1" M36x2 28 33 88 41
20 32 31.8 20 1 1/4" M45x2 35 37 98 50
24 40 38.1 24 1 1/2" M52x2 42 39 109 60
HA69O'RING METRIC FEMALE -24° CONE
LOOSE NUT - HEAVY TYPE
Hose I.D. Thread Tube Dimensions(mm)
DN mm SIZE Inch F mm H L S
O4 6 6.3 04 1/4" M16x1,5 8 24 53 19
O4 6 6.3 04 1/4" M18x1,5 10 25 54 22
O6 10 9.5 06 3/8" M20x1,5 12 25 56 24
O6 10 9.5 06 3/8" M22x1,5 14 29 60 27
O8 12 12.7 08 1/2" M24x1,5 16 31 64 30
10 16 15.9 10 5/8" M30x2 20 35 71 36
12 20 19.1 12 3/4" M36x2 25 39 80 46
16 25 25.4 16 1" M42x2 30 41 96 50
20 32 31.8 20 1 1/4" M52x2 38 47 108 60
HOSE CONNECTORS
CODE
CODE
METRIC FEMALE (LIGHT) STANDARD
METRIC FEMALE (HEAVY) STANDARD
23
HOSE CONNECTORS 2001
HG67 90° O-RING METRIC SWEPT ELBOW - 24° CONESOLID - LOOSE NUT - LIGHT TYPE
Hose I.D. Thread Tube Dimensions(mm)
DN mm SIZE Inch F mm H L K S
4 6 6.3 04 1/4" M12x1,5 6 24 52 28 17
4 6 6.3 04 1/4" M14x1,5 8 24 52 28 17
6 10 9.5 06 3/8" M16x1,5 10 34 64 36 19
6 10 9.5 06 3/8" M18x1,5 12 34 64 35 22
8 12 12.7 08 1/2" M22x1,5 15 41 74 41 27
10 16 15.9 10 5/8" M26x1,5 18 49 85 49 32
12 20 19.1 12 3/4" M30x2 22 58 99 54 36
16 25 25.4 16 1" M36x2 28 74 129 68 41
20 32 31.8 20 1 1/4" M45x2 35 92 153 86 50
24 40 38.1 24 1 1/2" M52x2 42 108 179 96 60
HG69 90° O-RING METRIC SWEPT ELBOW - 24° CONESOLID - LOOSE NUT - HEAVY TYPE
Hose I.D. Thread Tube Dimensions(mm)
DN mm SIZE Inch F mm H L K S
O4 6 6.3 04 1/4" M16x1,5 8 24 52 28 19
O4 6 6.3 04 1/4" M18x1,5 10 24 52 30 22
O6 10 9.5 06 3/8" M20x1,5 12 34 64 35 24
O6 10 9.5 06 3/8" M22x1,5 14 34 64 37 27
O8 12 12.7 08 1/2" M24x1,5 16 41 74 42 30
10 16 15.9 10 5/8" M30x2 20 49 85 53 36
12 20 19.1 12 3/4" M36x2 25 58 99 59 41
16 25 25.4 16 1" M42x2 30 74 129 71 50
20 32 31.8 20 1 1/4" M52x2 38 92 153 86 60
HOSE CONNECTORS
CODE
CODE
METRIC FEMALE 90 DEG (LIGHT)STANDARD
METRIC FEMALE 90 DEG (HEAVY)STANDARD
24
HOSE CONNECTORS
HJ6745° O-RING METRIC SWEPT ELBOW - 24° CONE
SOLID - LOOSE NUT - LIGHT TYPE
Hose I.D. Thread Tube Dimensions(mm)
DN mm SIZE Inch F mm H L K S
O4 6 6.3 04 1/4" M12x1,5 6 43.0 71.5 19.0 17
O4 6 6.3 04 1/4" M14x1,5 8 39.5 68.0 16.0 17
O6 10 9.5 06 3/8" M16x1,5 10 58.0 88.0 23.5 19
O6 10 9.5 06 3/8" M18x1,5 12 53.0 83.5 19.0 22
O8 12 12.7 08 1/2" M22x1,5 15 62.0 95.0 22.5 27
10 16 15.9 10 5/8" M26x1,5 18 79.0 115.0 26.0 32
12 20 19.1 12 3/4" M30x2 22 87.0 127.5 31.0 36
16 25 25.4 16 1" M36x2 28 109.0 164.0 40.0 41
20 32 31.8 20 1 1/4" M45x2 35 137.5 198.5 53.0 50
24 40 38.1 24 1 1/2" M52x2 42 161.5 231.5 56.5 60
HJ6945° O-RING METRIC SWEPT ELBOW - 24° CONE
SOLID - LOOSE NUT - HEAVY TYPE
Hose I.D. Thread Tube Dimensions(mm)
DN mm SIZE Inch F mm H L K S
O4 6 6.3 04 1/4" M16x1,5 8 39.5 68.0 16.0 19.0
O4 6 6.3 04 1/4" M18x1,5 10 40.5 69.0 16.5 22.0
O6 10 9.5 06 3/8" M20x1,5 12 53.0 83.5 19.0 24.0
O6 10 9.5 06 3/8" M22x1,5 14 54.5 85.0 20.5 27.0
O8 12 12.7 08 1/2" M24x1,5 16 63.5 96.5 24.0 30.0
10 16 15.9 10 5/8" M30x2 20 81.5 117.5 28.0 36.0
12 20 19.1 12 3/4" M36x2 25 90.0 131.0 35.5 41.0
16 25 25.4 16 1" M42x2 30 110.0 165.0 41.5 50.0
20 32 31.8 20 1 1/4" M52x2 38 139.0 200.0 54.0 60.0
HOSE CONNECTORS
METRIC FEMALE (LIGHT ) 45 DEG
STANDARD TIEFFEPart. N°
METRIC FEMALE (HEAVY) 45 DEG
STANDARD CODE
25
2001
HOSE CONNECTORS 2001
HA76 "KOMATSU" METRIC FEMALE - 60º CONE SEATPRESSED NUT
Hose I.D. Thread
DN mm SIZE Inch F
O4 6 6.3 04 1/4" M14x1,5
O6 10 9.5 06 3/8" M18x1,5
O8 12 12.7 08 1/2" M22X1,5
10 16 15.9 10 5/8" M24x1,5
12 20 19.1 12 3/4" M30x1,5
16 25 25.4 16 1" M33x15
20 32 31.8 20 1 1/4" M36x1,5
24 40 38.1 24 1 1/2" M42x1,5
HA83WASHCLEANER FEMALE
"FK" TYPE
Hose I.D. Thread Dimensions(mm)
DN mm SIZE Inch F H L D
O4 6 6.3 04 1/4" M22x1,5 31 59.5 14
O5 8 7.9 05 5/16" M22x1,5 31 59.5 14
O6 10 9.5 06 3/8" M22x1,5 31 61.5 14
HA92B.S.P. BANJO
SOLID
Hose I.D. BoltDimensions
(mm)
DN mm SIZE Inch Thread H L D S
O4 6 6.3 04 1/4" 1/4"-19 24.5 65.0 13.3 14.0
O6 10 9.5 06 3/8" 3/8"-19 26.5 71.0 16.9 17.0
O8 12 12.7 08 1/2" 1/2"-14 31.0 82.0 21.0 23.5
10 16 15.9 10 5/8" 5/8"-14 32.5 88.5 23.3 25.0
12 20 19.1 12 3/4" 3/4"-14 37.5 101.0 26.5 30.0
16 25 25.4 16 1" 1"-11 50.5 134.5 33.5 38.0
HOSE CONNECTORS
CODE
CODE
KOMATSU FEMALE STANDARD
K ARCHER FEMALE STANDARD
BSP BANJOCODE
26
D
HOSE CONNECTORS 2001
HA93 METRIC BANJO - ONE PIECE
Hose I.D. BoltDimensions
(mm)
DN mm SIZE Inch Thread H L D S
O4 6 6.3 04 1/4" M14x1,5 24.5 65.0 14.1 14.0
O6 10 9.5 06 3/8" M16x1,5 25.5 71.0 16.1 16.0
O8 12 12.7 08 1/2" M18x1,5 31.5 80.5 18.1 20.0
10 16 15.9 10 5/8" M22x1,5 34.0 88.0 22.1 23.5
12 20 19.1 12 3/4" M30x1,5 43.5 111.5 30.1 36.0
HA96 DOUBLE INSERT
Hose I.D. Dimensions(mm)
DN mm SIZE Inch H L
O4 6 6.3 04 1/4" 13 70
O5 8 7.9 05 5/16" 13 70
O6 10 9.5 06 3/8" 13 74
O8 12 12.7 08 1/2" 15 81
10 16 15.9 10 5/8" 15 87
12 20 19.1 12 3/4" 17 99
16 25 25.4 16 1" 20 130
HOSE CONNECTORS
CODE
CODE
METRIC BANJO
DOUBLE INSERT
27
D
ADAPTORS 2001
ADAPTORS
JIC MALE XJIC MALE
BSP MALE XBSP FEMALE
BSP FEMALE X BSP FEMALE
BSP BULKHEAD BSP LOCKNUT BSP BLANKING PLUG
BSP MALE / MALE 90ºELBOW
BSP MALE / FEMALE 90ºCOMPACT ELBOW
JIC MALE X NPTFMALE 90º ELBOW
JIC MALE XSAE 'O' RINGBOSS MALE
BSP MALE XSAE 'O' RINGBOSS MALE
BSP MALE X FEMALEREDUCING BUSH
BSP MALE XMETRIC MALE
BSP MALE X JIC FEMALE
JIC BLANKING PLUG BSP EQUAL FEMALE 'T' JIC MALE X SAE'O'RINGBOSS ADJUSTER 90º
JIC MALE XJIC FEMALE 90º
BSP TEE MALE/MALE MALE EQUAL
JIC MALE XMALE X FEMALE TEE
BSP BLANKING CAP METRIC MALE X MALE JIC MALE BULKHEADWITH LOCKNUT
BSP TEE MALE X MALEX FEMALE
BSP TEE MALE XFEMALE / MALE
BSP MALE X FEMALE45º SWEPT ELBOW
BSP MALE / FEMALE90º SWEPT ELBOW
BANJO BOLT METRIC PLUG METRIC CAP
28
BSP MALE XBSP MALEEQUAL
BSP MALE XBSP MALEUNEQUAL
BSP MALE XBSP TAPERMALE
BSP MALE XNPTF MALE
BSP MALE XJIC MALE
JIC MALE XNPTF MALE
STEEL TUBING 2001
HWMTSEAMLESS STEEL TUBES DIN 2391 MATERIAL ST
37.4 NBK
THICKNESS STATIC DYNAMIC BURST KG/MTR
MM W/P BAR W/P BAR PRE. BAR APPROX
4 0.75 409 393 1,820 0.063
5 1 432 416 2,120 0.099
6 1 389 374 1,680 0.123
6 1.5 549 528 3,050 0.166
6 1 333 289 1,190 0.173
8 1.5 431 414 1,860 0.24
10 1 282 249 870 0.222
10 1.5 373 358 1,380 0.314
12 1.5 353 305 1,150 0.388
12 2 409 393 1,580 0.493
14 1.5 302 265 940 0.462
15 1.5 282 249 980 0.499
15 2 376 323 1,250 0.641
16 2 353 305 1,170 0.691
18 1.5 235 210 780 0.61
18 2 313 274 1,040 0.789
20 1.5 212 191 570 0.684
20 2 282 249 920 0.888
20 2.5 353 305 1,220 1.079
22 2 256 228 850 0.986
22 2.5 320 280 1,040 1.202
25 2.5 282 249 920 1.387
25 3 338 294 1,050 1.628
28 2 201 182 620 1.282
28 2.5 252 224 770 1.572
28 3 302 265 920 1.85
30 3 282 249 920 1.998
35 2.5 201 182 620 2.004
35 3 242 216 720 2.367
38 2.5 186 168 550 2.189
38 4 297 261 970 3.354
42 3 201 182 580 2.885
STEEL TUBING
OD
Steel Tubes DIN 2391
29
Accessories 2001
H4000
SIZE ININCHES
MM INCHES
BSP NPT
2 1/8 1/8
4 1/4 1/4
6 3/8 3/8
8 1/2 1/2
12 3/4 3/4
16 1 1
10
12
15
19
21
23
26
31 31
33 33
37 37
40 40
41 41
47 47
52 52
CODE
HZP
CODE
QUICK RELEASE COUPLINGS
SPRING GUARDSSIZE IN
MM
ID
10
12
15
19
21
23
26
ID IDCODE CODE
10
BONDEDBONDED
10
12 12
14 14
16 16
18 18
20 20
22 22
24 24
26 26
28 28
30 30
36 36
2
4
6
8
10
12
16
20
24
32
1/8
1/4
3/8
1/2
5/8
3/4
1
1 1/4
1 1/2
2
DOWTY SEALS - METRIC
DOWTY SEALS - INCH SIZES
HZS01HZS05
30Accessories
Other Products
Other Products
2001
Other Products RangeAircondition and Refrigeration Hoses
Steel Braided fuel hoses
Oil Suction/Delivery hoses
Water Suction/Delivery hoses
Air Hoses
Radiator hoses
PVC reinforced hoses
Cement hoses
Oxygen/Acetylene hoses
Nylon Tubing
Copper Tubing
Reusable fittings in different threads and sizes
Eremeto Fittings
Brass Compression fittings
Brass Adaptors
Brass Low pressure fittings
Stainless Steel compression fittings
Camlock Coupling, King Nipples etc.
Bolt clamps, Steel clips
Tube clamps
Brass Air Coupler
Plastic Connectors
Ball Valves and Gate Valves
"O" Rings, Copper washers etc.
31
Technical Information 2001
32Technical Information
2001
33
Technical Information
Technical Information
2001
1 KP
a =
0.14
5 PS
I = 1
/100
BAR
= 0
.010
19KG
/SQ
CM
EXAM
PLE
:- 21
.1 K
G/S
Q C
M =
300
PSI
= 2
0.6
BAR
S =
2060
KPa
= 2
.06
Mpa
kg/sq
cmp.
s.Iba
rskg
/sq cm
p.s.I
bars
kg/sq
cmp.
s.Iba
rskg
/sq cm
p.s.I
bars
kg/sq
cmp.
s.Iba
rs21
.130
020
.69
161.
7423
0015
8.62
302.
3943
0029
6.55
443.
0463
0043
4.48
583.
6883
0057
2.41
24.6
350
24.1
416
5.26
2350
162.
0730
5.91
4350
300.
0044
6.55
6350
437.
9358
7.20
8350
575.
8628
.140
027
.59
168.
7824
0016
5.52
309.
4244
0030
3.45
450.
0764
0044
1.38
590.
7284
0057
9.31
31.6
450
31.0
317
2.29
2450
168.
9731
2.94
4450
306.
9045
3.59
6450
444.
8359
4.23
8450
582.
7635
.250
034
.48
175.
8125
0017
2.41
316.
4645
0031
0.34
457.
1065
0044
8.28
597.
7585
0058
6.21
38.7
550
37.9
317
9.32
2550
175.
8631
9.97
4550
313.
7946
0.62
6550
451.
7260
1.27
8550
589.
6642
.260
041
.38
182.
8426
0017
9.31
323.
4946
0031
7.24
464.
1466
0045
5.17
604.
7886
0059
3.10
45.7
650
44.8
318
6.36
2650
182.
7632
7.00
4650
320.
6946
7.65
6650
458.
6260
8.30
8650
596.
5549
.270
048
.28
189.
8727
0018
6.21
330.
5247
0032
4.14
471.
1767
0046
2.07
611.
8187
0060
0.00
52.7
750
51.7
219
3.39
2750
189.
6633
4.04
4750
327.
5947
4.68
6750
465.
5261
5.33
8750
603.
4556
.380
055
.17
196.
9128
0019
3.10
337.
5548
0033
1.03
478.
2068
0046
8.97
618.
8588
0060
6.90
59.8
850
58.6
220
0.42
2850
196.
5534
1.07
4850
334.
4848
1.72
6850
472.
4162
2.36
8850
610.
3463
.390
062
.07
203.
9429
0020
0.00
344.
5949
0033
7.93
485.
2369
0047
5.86
625.
8889
0061
3.79
66.8
950
65.5
220
7.45
2950
203.
4534
8.10
4950
341.
3848
8.75
6950
479.
3162
9.40
8950
617.
2470
.310
0068
.97
210.
9730
0020
6.90
351.
6250
0034
4.83
492.
2670
0048
2.76
632.
9190
0062
0.69
73.8
1050
72.4
121
4.49
3050
210.
3435
5.13
5050
348.
2849
5.78
7050
486.
2163
6.43
9050
624.
1477
.311
0075
.86
218.
0031
0021
3.79
358.
6551
0035
1.72
499.
3071
0048
9.66
639.
9491
0062
7.59
80.9
1150
79.3
122
1.52
3150
217.
2436
2.17
5150
355.
1750
2.81
7150
493.
1064
3.46
9150
631.
0384
.412
0082
.76
225.
0432
0022
0.69
365.
6852
0035
8.62
506.
3372
0049
6.55
646.
9892
0063
4.48
87.9
1250
86.2
122
8.55
3250
224.
1436
9.20
5250
362.
0750
9.85
7250
500.
0065
0.49
9250
637.
9391
.413
0089
.66
232.
0733
0022
7.59
372.
7153
0036
5.52
513.
3673
0050
3.45
654.
0193
0064
1.38
94.9
1350
93.1
023
5.58
3350
231.
0337
6.23
5350
368.
9751
6.88
7350
506.
9065
7.52
9350
644.
8398
.414
0096
.55
239.
1034
0023
4.48
379.
7554
0037
2.41
520.
3974
0051
0.34
661.
0494
0064
8.28
102
1450
100.
0024
2.62
3450
237.
9338
3.26
5450
375.
8652
3.91
7450
513.
7966
4.56
9450
651.
7210
5.5
1500
103.
4524
6.13
3500
241.
3838
6.78
5500
379.
3152
7.43
7500
517.
2466
8.07
9500
655.
1710
915
5010
6.90
249.
6535
5024
4.83
390.
3055
5038
2.76
530.
9475
5052
0.69
671.
5995
5065
8.62
112.
516
0011
0.34
253.
1636
0024
8.28
393.
8156
0038
6.21
534.
4676
0052
4.14
675.
1196
0066
2.07
116
1650
113.
7925
6.68
3650
251.
7239
7.33
5650
389.
6653
7.97
7650
527.
5967
8.62
9650
665.
5211
9.5
1700
117.
2426
0.20
3700
255.
1740
0.84
5700
393.
1054
1.49
7700
531.
0368
2.14
9700
668.
9712
3.1
1750
120.
6926
3.71
3750
258.
6240
4.36
5750
396.
5554
5.01
7750
534.
4868
5.65
9750
672.
4112
6.6
1800
124.
1426
7.23
3800
262.
0740
7.88
5800
400.
0054
8.52
7800
537.
9368
9.17
9800
675.
8613
0.1
1850
127.
5927
0.75
3850
265.
5241
1.39
5850
403.
4555
2.04
7850
541.
3869
2.69
9850
679.
3113
3.6
1900
131.
0327
4.26
3900
268.
9741
4.91
5900
406.
9055
5.56
7900
544.
8369
6.20
9900
682.
7613
7.1
1950
134.
4827
7.78
3950
272.
4141
8.42
5950
410.
3455
9.07
7950
548.
2869
9.72
9950
686.
2114
0.6
2000
137.
9328
1.29
4000
275.
8642
1.94
6000
413.
7956
2.59
8000
551.
7270
3.23
1000
068
9.66
144.
120
5014
1.38
284.
8140
5027
9.31
425.
4660
5041
7.24
566.
1080
5055
5.17
706.
7510
050
693.
1014
7.7
2100
144.
8328
8.33
4100
282.
7642
8.97
6100
420.
6956
9.62
8100
558.
6271
0.27
1010
069
6.55
151.
221
5014
8.28
291.
8441
5028
6.21
432.
4961
5042
4.14
573.
1481
5056
2.07
713.
7810
150
700.
0015
4.7
2200
151.
7229
5.36
4200
289.
6643
6.01
6200
427.
5957
6.65
8200
565.
5271
7.30
1020
070
3.45
158.
222
5015
5.17
298.
8742
5029
3.10
439.
5262
5043
1.03
580.
1782
5056
8.97
720.
8210
250
706.
90
PRES
SUR
E C
ON
VER
SIO
N C
HA
RT
34
1 ps
i = 0
.068
96 B
AR =
6.8
966
KPa
= 0.
0703
KG
/SQ
CM
1 BA
R =
14.
5 PS
I = 1
00 K
Pa =
1/1
0 M
Pa =
1.0
19 K
G/S
Q C
M1
KG/S
Q C
M =
14.
22 P
SI =
98.
1 KP
a =
.981
BAR
1 M
Pa =
145
PSI
= 1
0 BA
R =
10.
19 K
G/S
Q C
M
Technical Information
Technical Information
2001
35
Technical Information
Technical Information
2001
36
Technical Information
Technical Information
Trinity Mechanical Services LLC(Hydraulic Division)
P.O.Box 8807, Dubai - UAE, Tel: 04 2853342, Fax: 04 2853347Email: [email protected], www.trinityholdings.com
Assembly and Supply of:• Hydraulic Hoses and Fittings • Stainless steel corrugated hoses and fittings • Stainless steel expansion bellows • Steel tubes, tube fittings & tube clamps • Suction / Discharge, Air & Chemical hoses etc. • Pressure gauges, dowty seals, ball valves, quick release couplings etc