+ All Categories
Home > Documents > TSN System - Tech Data Sheets.xls

TSN System - Tech Data Sheets.xls

Date post: 14-Apr-2018
Category:
Upload: deepakjothivel
View: 226 times
Download: 0 times
Share this document with a friend

of 32

Transcript
  • 7/27/2019 TSN System - Tech Data Sheets.xls

    1/32

    M Thread Size

    Hole Size(mm)

    +0.05

    -0

    A (mm)

    +0

    -0.1

    B (mm)

    +0.2 D (mm)

    Min Max

    M 3 X 0.50 0.50 2.00 5.10 5.00 6.00 0.50

    M 4 X 0.70 0.50 2.50 6.10 6.00 7.00 0.50

    M 5 X 0.80 0.50 2.50 7.10 7.00 8.00 0.50

    M 6 X 1.00 1.00 4.00 9.10 9.00 10.00 0.50

    M 8 X 1.25 1.00 4.00 11.11 11.00 12.00 0.50

    M 10 X 1.50 1.00 4.00 13.10 13.00 14.00 0.50

    Special / Custom made sizes also available on request.

    Thread Size

    Pull-Out

    KN

    Push-out

    KN

    Torque-To-

    Turn

    Nm*

    Maximum

    Torque to be

    applied to

    bolt Nm**

    M 3 X 0.50 2.70 0.80 0.40 1.50

    M 4 X 0.70 6.60 1.50 1.90 5.10

    M 5 X 0.80 8.00 1.90 2.60 7.90

    M 6 X 1.00 11.40 2.40 3.40 12.40

    M 8 X 1.25 15.70 2.80 3.60 16.40M 10 X 1.50 18.70 3.70 4.20 33.90

    STRENGTH DATA

    * Torque-To-Turn

    These figures

    represent the

    ** Maximum Torque

    These figuresrepresent the

    50272 SeriesOpen End, Countersunk Head, Plain

    Dimensions in millimeters

    Grip Range

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    2/32

    M (mm)

    +0.2 Part Number

    9.00 50272-03020

    10.00 50272-04025

    12.00 50272-05025

    15.00 50272-06040

    16.00 50272-08040

    18.00 50272-01040

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    3/32

    M Thread Size

    Hole

    Size

    (mm)

    +0.05

    -0

    A (mm)

    +0

    -0.1

    B (mm)

    +0.2 D (mm)

    M (mm)

    +0.2

    Min Max

    M 3 X 0.50 0.50 2.00 4.90 4.80 5.80 0.50 9.00

    M 4 X 0.70 0.50 2.50 6.40 6.30 7.30 0.50 10.00

    M 5 X 0.80 0.50 2.50 7.20 7.10 8.10 0.50 12.00M 6 X 1.00 1.00 4.00 9.60 9.50 10.50 0.50 15.00

    M 8 X 1.25 1.00 4.00 10.60 10.50 11.50 0.50 16.00

    M 10 X 1.50 1.00 4.00 12.80 12.70 13.70 0.50 18.00

    Special / Custom made sizes also available on request.

    Thread Size

    Pull-

    Out KN

    Push-

    out

    KN

    Torque-To-

    Turn

    Nm*

    Maximum

    Torque to

    be applied

    to bolt Nm**

    M 3 X 0.50 2.70 0.80 0.40 1.50

    M 4 X 0.70 6.60 1.50 1.90 5.10

    STRENGTH DATA

    * Torque-To-Turn These

    figures represent the

    5558 SeriesOpen End, Countersunk Head, Plain

    Dimensions in millimeters

    Grip Range

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    4/32

    M 5 X 0.80 8.00 1.90 2.60 7.90

    M 6 X 1.00 11.40 2.40 3.40 12.40

    M 8 X 1.25 15.70 2.80 3.60 16.40

    M 10 X 1.50 18.70 3.70 4.20 33.90

    minimum torque applied

    to cause the fastener to

    turn in the parent material.

    ** Maximum Torque

    These figures represent

    the maximum

    recommended torque to

    be applied to the bolt,

    which will not cause

    thread distortion or failure

    in the insert

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    5/32

    Part Number

    50271-03020

    50271-04025

    50271-0502550271-06040

    50271-08040

    50271-01040

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    6/32

    M Thread Size

    Hole

    Size

    (mm)

    +0.05

    -0

    A (mm)

    +0

    -0.1

    B (mm)

    +0.2 D (mm)

    M (mm)

    +0.2

    Min Max

    M 3 X 0.50 0.50 2.00 5.10 5.00 8.00 0.80 9.80

    M 4 X 0.70 0.50 2.50 6.10 6.00 9.00 0.80 11.30

    M 5 X 0.80 0.50 2.50 7.10 7.00 10.00 1.00 12.50

    M 6 X 1.00 1.00 3.50 9.10 9.00 13.00 1.50 16.00

    M 8 X 1.25 1.00 4.00 11.10 11.00 14.50 1.50 18.00

    M 10 X 1.50 1.00 4.00 13.10 13.00 16.00 1.50 21.60

    Special / Custom made sizes also available on request.

    STRENGTH DATA

    50280 SeriesOpen End, Large Flange Head, Plain

    Dimensions in millimeters

    Grip Range

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    7/32

    Thread Size

    Pull-

    Out

    KN

    Push-

    out

    KN

    Torque-

    To-Turn

    Nm*

    Maximum

    Torque to

    be applied

    to bolt

    Nm**

    M 3 X 0.50 4.20 1.80 0.80 1.50

    M 4 X 0.70 5.50 2.90 1.50 5.10

    M 5 X 0.80 8.00 4.20 3.00 7.90

    M 6 X 1.00 10.80 6.50 3.40 12.40

    M 8 X 1.25 12.50 7.90 5.60 32.00

    M 10 X 1.50 17.30 10.70 13.80 45.00

    * Torque-To-Turn These

    figures represent the

    minimum torque applied

    to cause the fastener to

    turn in the parent material.

    ** Maximum Torque

    These figures represent

    the maximum

    recommended torque to

    be applied to the bolt,which will not cause

    thread distortion or failure

    in the insert

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    8/32

    Part Number

    50280-03020

    50280-04025

    50280-05025

    50280-06035

    50280-08040

    50280-01040

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    9/32

    M Thread Size

    Hole

    Size

    (mm)

    +0.05

    -0

    A (mm)

    +0

    -0.1

    B (mm)

    +0.2 D (mm)

    M (mm)

    +0.2

    Min Max

    M 4 X 0.70 0.50 2.50 6.10 6.00 7.00 0.50 10.00

    M 5 X 0.80 0.50 2.50 7.10 7.00 8.00 0.50 12.00

    M 6 X 1.00 1.00 4.00 9.10 9.00 10.00 0.50 15.00

    M 8 X 1.25 1.00 4.00 11.10 11.00 12.00 0.50 16.00

    M 10 X 1.50 1.00 4.00 13.10 13.00 14.00 0.50 18.60

    Special / Custom made sizes also available on request.

    STRENGTH DATA

    50372 SeriesOpen End, Countersunk Head, Serrated

    Dimensions in millimeters

    Grip Range

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    10/32

    Thread Size

    Pull-

    Out

    KN

    Push-

    out

    KN

    Torque-

    To-Turn

    Nm*

    Maximum

    Torque to

    be applied

    to bolt

    Nm**

    M 4 X 0.70 3.60 1.20 2.00 5.10

    M 5 X 0.80 7.80 1.40 2.80 7.90

    M 6 X 1.00 15.80 2.60 5.00 12.40

    M 8 X 1.25 18.10 3.50 9.10 16.40

    M 10 X 1.50 21.00 4.50 10.50 33.90

    * Torque-To-Turn These

    figures represent the

    minimum torque applied

    to cause the fastener to

    turn in the parent material.

    ** Maximum Torque

    These figures represent

    the maximum

    recommended torque to

    be applied to the bolt,which will not cause

    thread distortion or failure

    in the insert

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    11/32

    Part Number

    50372-04025

    50372-05025

    50372-06040

    50372-08040

    50372-01040

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    12/32

    M Thread Size

    o e

    Size

    (mm)

    +0.05

    -0

    A (mm)

    Max

    B (mm)

    Nom.

    D (mm)

    Max

    M (mm)

    Max

    Min Max

    M 4 X 0.70 0.50 2.00 6.80 6.75 7.50 0.50 11.45

    M 5 X 0.80 0.50 3.30 7.60 7.55 8.25 0.50 12.85

    M 6 X 1.00 0.70 4.00 10.00 9.90 10.65 0.50 15.50

    M 8 X 1.25 0.70 3.80 13.50 13.45 14.20 0.50 18.30

    Special / Custom made sizes also available on request.

    Thread Size

    Pull-

    Out

    KN

    Push-

    out

    KN

    Torque-

    To-Turn

    Nm*

    Maximum

    Torque to

    be applied

    to bolt

    Nm**

    STRENGTH DATA

    50370 SeriesOpen End, Countersunk Head, Serrated

    Dimensions in millimeters

    Grip Range

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    13/32

    M 4 X 0.70 3.60 1.20 2.00 5.10

    M 5 X 0.80 7.80 1.40 2.80 7.90

    M 6 X 1.00 15.80 2.60 5.00 12.40

    M 8 X 1.25 18.10 3.50 9.10 16.40

    * Torque-To-Turn These

    figures represent the

    minimum torque applied

    to cause the fastener toturn in the parent material.

    ** Maximum Torque

    These figures represent

    the maximum

    recommended torque to

    be applied to the bolt,

    which will not cause

    thread distortion or failure

    in the insert

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    14/32

    Part Number

    50370-04020

    50370-05033

    50370-06040

    50370-08038

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    15/32

    M Thread Size

    Hole

    Size

    (mm)

    +0.05

    -0

    A (mm)

    +0

    -0.1

    B (mm)

    +0.2 D (mm)

    M (mm)

    +0.2

    Min Max

    M 3 X 0.50 0.50 2.00 5.10 5.00 8.00 0.80 9.00

    M 4 X 0.70 0.50 2.50 6.10 6.00 9.00 0.80 10.50M 5 X 0.80 0.50 2.50 7.10 7.00 10.00 1.00 11.50

    M 6 X 1.00 1.00 3.50 9.10 9.00 13.00 1.50 14.50

    M 8 X 1.25 1.00 4.00 11.10 11.00 14.50 1.50 16.50

    M 10 X 1.50 1.00 4.00 13.10 13.00 16.00 1.50 19.00

    Special / Custom made sizes also available on request.

    Thread Size

    Pull-

    Out KN

    Push-

    out

    KN

    Torque-To-

    Turn

    Nm*

    Maximum

    Torque to

    be applied

    to bolt Nm**

    M 3 X 0.50 4.20 1.80 1.10 1.50

    M 4 X 0.70 5.50 2.90 2.20 5.10

    STRENGTH DATA

    * Torque-To-Turn These

    figures represent the

    50380 SeriesOpen End, Countersunk Head, Serrated

    Dimensions in millimeters

    Grip Range

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    16/32

    M 5 X 0.80 8.00 4.20 3.40 7.90

    M 6 X 1.00 10.80 6.50 4.70 12.40

    M 8 X 1.25 12.50 7.90 6.80 32.00

    M 10 X 1.50 17.30 10.70 16.70 45.00

    minimum torque applied

    to cause the fastener to

    turn in the parent material.

    ** Maximum Torque

    These figures represent

    the maximum

    recommended torque to

    be applied to the bolt,

    which will not cause

    thread distortion or failure

    in the insert

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    17/32

    Part Number

    50380-03020

    50380-0402550380-05025

    50380-06035

    50380-08040

    50380-01040

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    18/32

    M Thread Size

    Hole

    Size

    (mm)

    +0.05

    -0

    A (mm)

    +0

    -0.1

    B (mm)

    +0.08 D (mm)

    F

    +0.08 A/F

    M (mm)

    +0.2

    Min Max

    M 3 X 0.50 0.70 1.63 4.85 4.72 6.10 0.50 4.74 9.00

    M 4 X 0.70 0.51 1.63 6.40 6.33 8.00 0.70 6.29 10.40

    M 5 X 0.80 0.51 2.03 7.30 7.14 9.22 0.70 7.19 11.80

    M 6 X 1.00 0.76 2.92 9.65 9.53 11.94 0.90 9.54 14.60

    M 8 X 1.25 0.91 3.25 10.70 10.50 12.96 0.90 10.00 16.00

    Material:Steel 1006

    Coating:Cr3 Blue zinc plated

    Special / Custom made sizes also available on request.

    50470 SeriesOpen End, Countersunk Head,Half Hexagonal

    Dimensions in millimeters

    Grip Range

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    19/32

    Thread Size

    Pull-

    Out KN

    Push-

    out

    KN

    Torque-To-

    Turn

    Nm*

    Maximum

    Torque to

    be applied

    to bolt Nm**

    M 3 X 0.50 2.90 0.80 1.00 1.50

    M 4 X 0.70 4.20 1.30 4.00 5.10

    M 5 X 0.80 5.90 1.90 6.60 7.90

    M 6 X 1.00 6.90 2.40 8.70 12.40

    M 8 X 1.25 14.80 2.80 11.80 16.40

    * Torque-To-Turn

    These figures

    represent the

    minimum torque

    applied to cause the

    fastener to turn in

    the parent material.

    ** Maximum Torque

    These figures

    represent the

    maximum

    recommended

    torque to be applied

    to the bolt, which

    will not cause

    thread distortion or

    failure in the insert

    STRENGTH DATA

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    20/32

    Part Number

    50470-03016

    50470-04016

    50470-05020

    50470-06029

    50470-08033

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    21/32

    M Thread Size

    Hole

    Size

    (mm)

    +0.05

    A (mm)

    +0.08

    B (mm)

    +0.2

    D (mm)

    +0.13

    F

    +0.08 A/F

    Min Max

    M 4 X 0.70 0.50 2.00 6.00 5.89 8.98 1.00 5.89

    M 4 X 0.70 2.00 4.00 6.00 5.89 8.98 1.00 5.89

    M 5 X 0.80 0.50 3.00 7.00 6.89 9.98 1.00 6.89

    M 5 X 0.80 3.00 5.50 7.00 6.89 9.98 1.00 6.89

    M 6 X 1.00 0.50 3.00 9.00 8.89 13.00 1.50 8.89

    M 6 X 1.00 3.00 5.50 9.00 8.89 13.00 1.50 8.89

    M 8 X 1.25 0.50 3.00 11.00 10.89 15.98 1.50 10.89

    M 8 X 1.25 3.00 5.50 11.00 10.89 15.98 1.50 10.89

    M 10 X 1.50 1.00 3.50 13.00 12.89 19.00 2.00 12.89

    M 10 X 1.50 3.50 5.50 13.00 12.89 19.00 2.00 12.89

    Special / Custom made sizes also available on request.

    Thread Size

    Pull-

    Out

    KN

    Push-

    out

    KN

    Torque-

    To-Turn

    Nm*

    Maximum

    Torque to

    be applied

    to bolt

    Nm**

    STRENGTH DATA

    50480 SeriesOpen End, Large Flange, Hexagonal

    Dimensions in millimeters

    Grip Range

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    22/32

    M 4 X 0.70 6.30 2.20 4.50 5.10

    M 5 X 0.80 8.80 3.60 8.60 7.90

    M 6 X 1.00 14.40 5.30 11.90 12.40

    M 8 X 1.25 15.00 8.00 25.00 32.00

    M 10 X 1.50 19.70 9.20 45.20 45.00

    * Torque-To-Turn These

    figures represent the

    minimum torque applied

    to cause the fastener to

    turn in the parent

    material.

    ** Maximum Torque

    These figures represent

    the maximum

    recommended torque to

    be applied to the bolt,

    which will not cause

    thread distortion or failure

    in the insert

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    23/32

    M (mm)

    Nom Part Number

    10.00 50480-04020

    12.00 50480-04040

    13.20 50480-05030

    15.70 50480-05055

    15.50 50480-06030

    18.00 50480-06055

    18.00 50480-08030

    20.50 50480-08055

    21.00 50480-01035

    23.00 50480-01055

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    24/32

    M Thread Size

    Hole

    Size

    (mm)

    +0.1

    -0.0

    A (mm)

    +0.1

    -0.0

    F

    +0.3

    D (mm)

    +0.15

    -0.05

    M (mm)

    +0.4

    Min Max

    M 4 X 0.70 0.50 2.50 6.10 5.90 9.00 0.90 10.70M 5 X 0.80 0.50 3.00 7.10 6.90 10.00 0.90 13.70

    M 6 X 1.00 0.50 3.30 9.10 8.90 13.00 1.50 16.00

    M 8 X 1.25 0.50 3.30 11.10 10.90 16.00 1.50 18.00

    M 10 X 1.50 0.50 3.50 13.10 12.90 19.00 2.00 21.00

    Special / Custom made sizes also available on request.

    Thread Size

    Pull-Out

    KN

    Push-out

    KN

    Torque-To-Turn

    Nm*

    Maximum

    Torque to

    be appliedto bolt

    Nm**

    M 4 X 0.70 6.30 2.20 4.50 5.10

    STRENGTH DATA

    * Torque-To-Turn These

    figures represent the

    50580 SeriesOpen End, Large Flange Head, Hexagonal

    Dimensions in millimeters

    Grip Range

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    25/32

    M 5 X 0.80 8.80 3.60 8.60 7.90

    M 6 X 1.00 14.40 5.30 11.90 12.40

    M 8 X 1.25 15.00 8.00 25.00 32.00

    M 10 X 1.50 19.70 9.20 45.20 45.00

    minimum torque applied

    to cause the fastener to

    turn in the parent material.

    ** Maximum Torque

    These figures represent

    the maximum

    recommended torque to

    be applied to the bolt,

    which will not cause

    thread distortion or failure

    in the insert

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    26/32

    Part Number

    50580-0402550580-05030

    50580-06033

    50580-08033

    50580-01035

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    27/32

    M Thread Size

    Hole

    Size

    (mm)

    +0.1

    -0.0

    A (mm)

    +0.1

    -0.1

    F

    +0.3

    D (mm)

    +0.15

    -0.05

    Min Max

    M 4 X 0.70 0.50 2.50 6.10 5.90 6.90 0.50M 5 X 0.80 0.50 3.00 7.10 6.90 7.80 0.50

    M 6 X 1.00 0.50 3.30 9.10 8.90 10.00 0.50

    M 8 X 1.25 0.50 3.00 11.00 11.00 11.80 0.70

    M 10 X 1.50 0.50 3.50 13.10 12.90 14.60 0.80

    Special / Custom made sizes also available on request.

    Thread Size

    Pull-Out

    KN

    Push-out

    KN

    Torque-To-Turn

    Nm*

    Maximum

    Torque to

    be appliedto bolt

    Nm**

    M 4 X 0.70 6.30 2.20 4.50 5.10

    STRENGTH DATA

    * Torque-To-Turn These

    figures represent the

    50570 SeriesOpen End, Low Profile Head, full Hexagonal

    Dimensions in millimeters

    Grip Range

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    28/32

    M 5 X 0.80 8.80 3.60 8.60 7.90

    M 6 X 1.00 14.40 5.30 11.90 12.40

    M 8 X 1.25 15.00 8.00 25.00 32.00

    M 10 X 1.50 19.70 9.20 45.20 45.00

    minimum torque applied

    to cause the fastener to

    turn in the parent material.

    ** Maximum Torque

    These figures represent

    the maximum

    recommended torque to

    be applied to the bolt,

    which will not cause

    thread distortion or failure

    in the insert

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    29/32

    M (mm) +0.4 Part Number

    10.20 50570-0402512.00 50570-05030

    15.20 50570-06033

    18.00 50570-08033

    21.00 50570-01035

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    30/32

    M Thread Size

    Hole

    Size

    (mm)

    +0.05

    -0

    A (mm)

    +0

    -0.1

    F

    +0.2 D (mm)

    M (mm)

    +0.2

    Min Max

    M 4 X 0.70 0.50 2.50 6.40 6.30 7.30 0.50 10.00

    M 5 X 0.80 0.50 2.50 7.20 7.10 8.10 0.50 12.00M 6 X 1.00 1.00 4.00 9.60 9.50 10.50 0.50 15.00

    M 8 X 1.25 1.00 4.00 10.60 10.50 11.50 0.50 16.00

    Special / Custom made sizes also available on request.

    Thread Size

    Pull-

    Out

    KN

    Push-

    out

    KN

    Torque-

    To-Turn

    Nm*

    Maximum

    Torque to

    be applied

    to bolt

    Nm**

    M 4 X 0.70 6.60 1.50 1.90 5.10

    M 5 X 0.80 8.00 1.90 2.60 7.90

    STRENGTH DATA

    * Torque-To-Turn These

    figures represent the

    minimum torque applied

    to cause the fastener to

    turn in the parent material.

    50371 SeriesOpen End, Countersunk Head, Serrated

    Dimensions in millimeters

    Grip Range

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    31/32

    M 6 X 1.00 11.40 2.40 3.40 12.40

    M 8 X 1.25 15.70 2.80 3.60 16.40

    M 10 X 1.50 18.70 3.70 4.20 33.90

    ** Maximum Torque

    These figures represent

    the maximum

    recommended torque to

    be applied to the bolt,

    which will not causethread distortion or failure

    in the insert

  • 7/27/2019 TSN System - Tech Data Sheets.xls

    32/32

    Part Number

    50371-04025

    50371-0502550371-06040

    50371-08040


Recommended