Date post: | 25-Dec-2015 |
Category: |
Documents |
Upload: | jane-sharp |
View: | 233 times |
Download: | 0 times |
About Us
www.tuskertransbelt.com
Tusker is the leading manufacturer of top quality industrial, automotive and agriculture application belts.
25 years of excellence in manufacturing drive belts including V and multi ribbed belts, cogged belts, space saver belts, fractional horse power belts and timing belts.
Tusker transmission belts are made as per original equipment specifications conforming to international standards and are designed for long life. Pre-stretched polyester tension cords, fibre reinforced belt ensure low maintenance and lateral stiffness.
Tusker has setup a State-of-the-art manufacturing plant in Malaysia exclusively cater to the high growth manufacturing sector as well as the industrial and agricultural sectors.
Products of Tusker Transmission
Industrial Classical V-Belts
& FHP Belts
Narrow (Wedge)
belts
Industrial Cogged Classical & Wedge Belts
Multi-rib Industrial Micro
Poly V-Belts
Industrial cogged Power wedge
belts
Hexagonal & Banded Belts
Double side Synchronous
Belts
Variable Speed Belts
Automotive V& Cogged
Belts
Automotive Poly V Serpentine
belts
Timing belts
Transmission AccessoriesCouplings & Elements
Variable Speed Belts
Features:o High efficiency of power transmission
at variable speed changes
o The strongly bonded reinforcement polyester cable cord and a specially treated high quality rubber
o These belts meet the specification of ISO1604 and other to customers’ requirements
www.tuskertransbelt.com
Top Width(mm)
Thickness
(mm)
Angle (mm)
22.2 8 22
30.2 11 22
36.5 12 22
46.0 14 26
69.9 17 30
Tusker Variable Speed Belts give superb resistance to section deviation while bending around small pulleys
Multi-rib Industrial Micro Poly v-belts
Tusker Multi-rib/Poly-rib belt represents a new venture to transmit high power rating and efficiency
www.tuskertransbelt.com
Design Features:o Speed ratio up to 40:1, smoother,
vibration free
o Low static, noise free, high flexibility rubber
o Reinforcement Polyester stiff cabled cord
o Use of single belts eliminate the necessity to use multiple for matched set of belts
Profile Pitch: P (mm)
High of Rib (mm)
PH 1.6 1.1
PJ 2.34 1.8
PK 3.56 2.4
PL 4.7 4.6
PM 9.4 9.4
No. of Ribs Section
6 PK
Raw Edge Cogged Automotive (Laminated)
Features:o Maximum resistance to slippage
o The Cog design helps optimum flexibility & allows cool air between the pulleys
o Raw edge Cogged automotive belts give higher belt life approximately 300% more than the wrapped belts
Top Width(mm)
Thickness(mm)
Angle (mm)
Range(0)
8 5.8 38 450-2540
9 5.8 38 450-2540
10 7.5 38 450-2540
11 7.5 38 450-2540
13 7.8 38 450-2540
17 9.5 38 450-2540
19 10.5 38 450-2540
22 11.5 38 450-2540
9.5 7.5 38 450-2540
13 7.5 38 450-2540
www.tuskertransbelt.com
• Tusker Industrial raw edge belts are available with extraordinary oil & heat, vibration resistance and antistatic properties
Tusker Industrial Raw Edge Cogged Belts
Section Cross Section
Inside Length
Pitch Length
AX 13 X 8 19 – 100
520 - 2540
BX 17 X 11 20 – 100
520 - 2540
CX 22 X 14 45 – 100
1200 - 2540
www.tuskertransbelt.com
Features:o High flexibility, low slippage and
reduced hysteresis loss than wrapped belts
o The mould cogged design of these belts run even in smaller pulley diameters and drive ratios up to 1:12
Industrial Cogged Power Wedge Belts
Features:o Helps the pulleys to remain cool
while running
o Compact, economical and more efficient than the conventional belts
o Resistant to oil & heat with very good antistatic properties
Type Width(mm)
Thickness (mm)
Angle Range(mm)
3VX 9.5 8 40 630-3550
5VX 15.9 13.5 40 1270-9000
8VX 25.4 22 40 2540-1270
SPZX 10.0 8.0 40 630-3550
SPAX 13.0 10.0 40 800-4500
SPBX 16.0 13.0 40 1250-8000
SPCX 22.0 18.0 40 2000-12500
www.tuskertransbelt.com
Wedge belts can achieve high speed and load between shorter centre-to-centre distance
Wedge Space Saver Wrapped Belts
Features:o Initial low cost
o Highly resistant to heat and oil resistance with antistatic properties
o Lowers the cost, as it reduces the number of belts required to operate as compared to the classical belts
Type Width(mm)
Thickness
(mm)
Angle Range(0)
SPX 10.0 8.0 40 630-3550
SPA 13.0 10.0 40 800-4500
SPB 16.0 13.0 40 1250-8000
SPC 22.0 18.0 40 2000-12500
www.tuskertransbelt.com
With one motor drive, Double Sided Synchronous Belts transmit the power of different directions with losing any power rating
Double Sided Synchronous Belts
Features:o Oil & heat resistant and antistatic
for maximum life efficiency
o Rubberized Chloroprene jacket fabric
o Reinforcement Polyester stiff cabled cord
o High Hardness Base Compound
Cross Section
TopWidth(mm)
Thickness
(mm)
Angle Range(0)
AA 13.0 10.2 40 60” - 240”
BB 16.7 13.4 40 60” - 240”
CC 22.0 19.0 40 130” - 480”
www.tuskertransbelt.com
FHP (Fractional horse power belts)
www.tuskertransbelt.com
Features:o Oil & heat resistance and anti-static
properties .o HMLS Polyester cord gives low stretch
and better flexibility.o Special compounded base gives good
flex fatigue resistance Applications:• Washing machines, Dish washers • Industrial Refrigerators • Industrial Fans, Blowers.
Tusker V-BeltsTusker V-belts have extraordinary dimensional stability in both storage and drive over long periods of time
www.tuskertransbelt.com
Features:o High hardness cushion
compound with maximum flexibility
o Resistant to crack initiation friction compound (Chloroprene)
o During the process of curing, all sets of belts are preciously matched free, set to higher efficiency and longer life
Section TopWidth(mm)
Thickness
(mm)
Angle Range(0)
A 13 8 40 15-180 380 – 4570
B 17 11 40 17-585 430 – 14860
C 22 14 40 36-600 915 – 15240
D 32 19 40 90-600 2290 – 15240
Mechanical demandso Tensile strengtho Bending stabilityo Abrasion resistance/Low
hysteresiso Longitudinal and
dimensional stability
Chemical demandsResistance to oils, grease, water, UV radiation
Demands on drive beltsWith modern hi-speed engine design, the demand on the drive belts are high, as they have to withstand very high mechanical, chemical and thermal demands
Thermal demandsHeat resistance with engine compartment temperature from -30 to +180 C
Demands
www.tuskertransbelt.com
Tusker Quality Control System
www.tuskertransbelt.com
Step 1Raw material are subjected to ISO specifications limit by testing: i) The specific gravityii) Melting pointiii)Solubilityiv)Loss on heatingv) Loss on ignition vi)Viscosityvii)Ash content through
acetone extractviii)pH value
Step 2The processing material (“Process-in-control”) tested to our specification limits like: i) Hardnessii) Specific gravityiii) Plasticityiv) Elongation at
breakv) Modulusvi) Agingvii) Adhesion test with
fabricviii) Reinforcement
polyester cord
Step 3Finally, the cured finished belts of each section and size are tested by means of dimensions, accelerated dynamic test, stretch test, abrasion test, standard oil testing, breaking strength, adhesion test
The 3 stages: