5-7YEARS
TWISTER
Length 105 - 125 cm / 41 - 49 inch
Max weight 30 kg / 66 lbs
Time to build 1.5 hours
CONSTRUCTION MANUAL
Before you start constructing and use our product, please carefully
read the following safety warning and download our manual from our
website. This safety warning and manual contains important informa-
tion relating to your child’s safety. It is your responsibility to review this
information with your child and make sure they are fully aware of all
the warnings before they start riding. Failure to follow instructions and
safety precautions can result in serious injury or death.
You can fi nd a digital copy of the manual at the following web address: www.infentorides.com
WARNING - IMPORTANT NOTICE TO PARENTS
PLEASE PRINT OUT THE MANUAL AND KEEP THE MANUAL AND THIS SAFETY WARNING IN A
SAFE LOCATION FOR FUTURE REFERENCE.
of serious injury: use only under close adult
lose control, fall off and/or get into dangerous
The rides that you can fi nd in our manuals been tested by offi cial independent testing
diff er from the offi cial rides that we show in our
Construction/assembly of a ride should
specifi c ride.
offi cial Infento manual.
fi nd the maximum weight for every specifi c ride
maximum length for every specifi c ride.
recommend riders always wear a properly fi tted
or fl ooring, by use of an Infento ride indoors.
the amount specifi ed in the manual
allow the chain to slip off the sprockets.
parts are still fi rmly
force (15Nm) to prevent them from coming loose.
GREAT INFENTO EXPERIENCE:
This Junior ride has to be assembled by an adult.
You can fi nd a digital copy of the manual at the following web address:
WARNING! PARENTAL SUPERVISION
AND APPROPRIATE USE
Like any moving product, rides made from
Infento parts can be dangerous if due care
and attention is not paid. To reduce the risk
of serious injury: use only under close adult supervision. Parents must review the following
warnings and instructions with each Infento
ride that is being build. It is your responsibility
to review this information and make sure that
all riders understand all warnings, cautions,
instructions and safety topics, and assure that
young riders are able to safely and responsibly
use this product. Infento recommends that you
periodically review and reinforce the infor-
mation in this manual with younger riders, and
that you inspect and maintain your child’s
Infento rides to insure their safety.
WARNING! RIDING ON
INFENTO RIDES CAN BE A
DANGEROUS ACTIVITY
Riding on Infento rides can be a dangerous
activity. Certain conditions may cause the equip-
ment to fail without fault of the manufacturer.
Rides made from Infento parts can and are
intended to move, and it is therefore possible to
lose control, fall off and/or get into dangerous situations that no amount of care, instruction or
expertise can eliminate. If such things occur you
can be seriously injured or die, even when using
safety equipment and other precautions. Ride at
your own risk and use common sense.
WARNING! NO LIABILITY FOR
CONSTRUCTED RIDES THAT
DIFFER FROM OUR MANUALS
The rides that you can fi nd in our manuals have
been tested by offi cial independent testing agencies. We will not be responsible or liable,
directly or indirectly, in any way for any loss or
damage of any kind incurred as a result of your
decision to build constructions or rides that
diff er from the offi cial rides that we show in our manuals.
ASSEMBLY – SUBSECTION
WARNING! OUR KITS
CONTAIN SMALL PARTS
This package contains small parts which, before
assembly, present a choking hazard to children
under the age of three. Care should be taken
during unpacking and assembly to insure that
all small parts and plastic bags are accounted
for and kept out of the reach of children.
WARNING! TO AVOID
SERIOUS INJURY:
1. Construction/assembly of a ride should always be under supervision of an adult
using the Infento manual for the
specifi c ride. 2. All fasteners (bolts and nuts) should be
fully tightened.
3. It is the responsibility of the adult who
assembles this bicycle to properly install all
parts included in the factory sealed shipping
carton and to make the adjustments to the
functional parts such as handle bar and seat
and chain when necessary.
USE – SUBSECTION
WARNING! TO AVOID
SERIOUS INJURY:
1. Continuous adult supervision is required.
2. Only ride constructed rides that have been
built according to the instructions given in the
offi cial Infento manual.3. Never exceed the maximum weight. You can
fi nd the maximum weight for every specifi c ride in our manual.
4. Always check the manual to see the minimum
and maximum age as well as the minimum and
maximum length for every specifi c ride.5. Always wear safety equipment such as a
helmet, knee pads and elbow pads. We
recommend riders always wear a properly fi tted helmet that complies with local or national
guidelines or laws. Keep chinstrap of helmet
securely buckled.
6. Always wear closed toed shoes (lace-up
shoes with rubber soles), never ride barefooted
or in sandals, and keep shoe laces tied and out
of the way of the wheels.
7. Avoid streets and surfaces with water, sand,
gravel, dirt, leaves, and other debris. Wet we-
ather impairs traction, braking and visibility.
8. Excessive exposure to sunlight, temperatures
below 0 degrees Celsius, water, sand, gravel,
dirt, leaves, and other debris can damage,
shrink, expand or weaken parts. Keep your ride
in a dry environment with proper heating.
9. Avoid sharp bumps, drainage grates and
sudden surface changes. Your Infento ride may
suddenly stop.
10. Ride on smooth, paved surfaces away from
SAFETY SECTION
motor vehicles. Wet, slick or uneven and rough
surfaces may impair traction and contribute to
possible accidents.
11. Never risk damaging surfaces, such as carpet
or fl ooring, by use of an Infento ride indoors. 12. Never use near motor vehicles, streets,
roadways, alleys, swimming pool areas, hills,
steps, sloped driveways, inclines and public
highways.
13. Watch out for pedestrians, skaters, skate-
boards, scooters, bikes, children or animals who
may enter your path, and respect the rights and
property of others.
14. Avoid excessive speed associated with
downhill rides.
15. Do not use at night or in periods with
reduced visibility.
16. Before every use, please make sure that
the complete ride and all joints have been
assembled tightly, as with use, joints may
wear out.
17. Before using your Infento ride, please check
that the screws are tightened securely.
18. It’s your own responsibility if you modify the
product other than manufacturer’s instructions.
19. Maintain a hold on the handlebars at all times.
20. Brake will get hot from continuous use.
Do not touch after braking.
21. Periodically check hardware and tighten
if necessary. Replace worn or broken parts
immediately.
22. Skill is required to avoid falls or collision
causing injury to the user and third parties.
23. Check operation of breaks every time
before bicycle is ridden.
24. Check local laws before you start with riding.
25. Never tow wagons, other vehicles, or
children on skates or skateboards.
26. Make certain that anyone who uses an
Infento ride has been fully instructed in its
operation.
27. Instruct your child on how to use the
breaks.
28. Do not perform stunts.
29. Never use headphones or a cell phone
when riding.
30. Only one rider at a time on an Infento ride.
31. Do not allow children to stand on the
product at any time.
FAILURE TO USE COMMON SENSE AND
HEED THE ABOVE WARNINGS INCREASES
RISK OF SERIOUS INJURY. USE WITH
APPROPRIATE CAUTION AND SERIOUS
ATTENTION TO SAFE OPERATION.
the amount specifi ed in the manual
allow the chain to slip off the sprockets.
parts are still fi rmly
force (15Nm) to prevent them from coming loose.
GREAT INFENTO EXPERIENCE:
You can fi nd a digital copy of the manual at the following web address:
of serious injury: use only under close adult
lose control, fall off and/or get into dangerous
The rides that you can fi nd in our manuals been tested by offi cial independent testing
diff er from the offi cial rides that we show in our
Construction/assembly of a ride should
specifi c ride.
offi cial Infento manual.
fi nd the maximum weight for every specifi c ride
maximum length for every specifi c ride.
recommend riders always wear a properly fi tted
or fl ooring, by use of an Infento ride indoors.
SAFETY SECTION
OUR KITS CONTAIN SMALL PARTS
This package contains small parts which,
before assembly, present a choking hazard to
children under the age of three. Care should be
taken during unpacking and assembly to insure
that all small parts and plastic bags are accounted
for and kept out of the reach of children.
QUESTIONS OR SUPPORT NEEDED?
You can mail us all your questions at:
and our team will reply you as soon
as possible.
INSTRUCTIONMAINTENANCE
1.
2.
3.
4.
5.
6.
7.
8.
Oil or grease moving parts periodically.
Check nuts and bolts often and tighten
if necessary.
Any parts showing evidence or wear should
be replaced immediately.
Follow closely the assembly instructions
pertaining to the proper adjustments of parts
Periodically check the brake system for
proper function
Periodically check the steering mechanism
for proper function
Check the air pressure in the tires to be
the amount specifi ed in the manualPeriodically check the bicycle’s tooth belt to
be sure that it is not too lose which could
allow the chain to slip off the sprockets.
RECOMMENDED TOOLS
4 x Allen key 3, 4, 5, 6 mm
5 x Wrench10, 13, 14, 15, 19 mm
1 x Tapeline
1 x T-handle for Allen key
parts are still fi rmly
force (15Nm) to prevent them from coming loose.
GREAT INFENTO EXPERIENCE:
ride TWISTER
1
version 1.0
Parrellel clamp joint L-joint Positioning block
+
Tighten the bolts with full force. Ensure that you hold the long side of the Allen key in your hand as this enables you to exert greater force.
Axle clamp
1x1x
+
2x
+ +
Locknut M8
1x Bolt M8x25(low head)
1x
take a 5mm Allen key, slide the nut on it
stick the Allen key through the part
let the nutslide down
BOLT-IN-PART-TRICK
2
1
3
Double check here:Does your result looks exactly like the image at the bottom of the page?
First, get all required materials stated here and then follow the instructions.
You can fi nd a digital copy of the manual at the following web address:
of serious injury: use only under close adult
lose control, fall off and/or get into dangerous
The rides that you can fi nd in our manuals been tested by offi cial independent testing
diff er from the offi cial rides that we show in our
Construction/assembly of a ride should
specifi c ride.
offi cial Infento manual.
fi nd the maximum weight for every specifi c ride
maximum length for every specifi c ride.
recommend riders always wear a properly fi tted
or fl ooring, by use of an Infento ride indoors.
the amount specifi ed in the manual
allow the chain to slip off the sprockets.
Check frequently if all
parts are still fi rmly tightened and function
properly.
Constructing and
playing always under
supervision of an adult.
Tighten bolts with full
force (15Nm) to prevent them from coming loose.
TOP 3 REQUIREMENTS MAKING A GREAT INFENTO EXPERIENCE:
1
2
3
ride TWISTER
2
version 1.0
15.75inch | 400mm xle
17.32inch | 440mm Axle
+
T-Positioning block
2x12.60inch | 320mm
le 14.17inch | 360mm
Profi le 1x
+
Bolt M8x20 (low head)
1x 1x
+
Tighten the bolts with full force. Ensure that you hold the long side of the Allen key in your hand as this enables you to exert greater force.
A
B
C
ride TWISTER
3
version 1.0
Positioning block
+
Axle clamp
1x
+
2x
+ +
Bolt M8x25(low head)
1xParrellel clamp joint L-joint
1xLocknut M8
1x
take a 5mm Allen key, slide the nut on it
stick the Allen key through the part
let the nutslide down
BOLT-IN-PART-TRICK
2
1
3
First, get all required materials stated here and then follow the instructions.
ride TWISTER
4
version 1.0
Locknut M6
4x
+
Bolt M8x20 (low head)
1x T-Positioning block
2xBrake caliper holder Bolt M6x25
4x
++
Leave a gap of at least 0.5mm when tightening the bolts.
A
B
C
ride TWISTER
5
version 1.0
++
T-Positioning block
2xProfi le nut short
1xU-Block
13x2.75-8
1x
+
Bolt M8x20
1x
6.3” | 160 mm
If you look carefully you can see that the sides of the profi le slope
slightly inwards. If you tighten a bolt securely the profi le will be pulled
fl ush against the block so the profi le is properly tensioned. As a result
the axle bolts remain more tightly in place. This is called tensile stress.
A
B
C
ride TWISTER
6
version 1.0
++
Bolt M8x20
2x T-Positioning block
4xMulti angle joint
2x
+
Profi le nut short
2x
A B
ride TWISTER
7
version 1.0
+
Wheel lock ring 8-42
7 inch wheel
Ducktail board
2xBolt M8x45
2x
+
Washer M8-16pulley protection 28T
2x
A wheel always has to be locked tightly with washers because the wheel might otherwise move over the axle. This way you ensure that the wheel does not touch anywhere and will not rattle. This is especially important when steering. Just imagine how diffi cult and hazardous it is to steer if your wheels are moving. This has to be considered for all vehicles with wheels. At Infento this is solved using spacer washers, so you can build freely but are still able to tighten the wheel properly.
A B
ride TWISTER
8
version 1.0
+
Handlebar short
1x
++
Axle plate1x
40x80_hexa 19
Bolt M5x6
1xMulti angle joint
1x
+
Profi le nut short
Bolt M8x25 Positioning block
1x
+
Positioning block
2x
A
B
C
ride TWISTER
9
version 1.0
belt pulley 28T
Handgrip
1x
A B
ride TWISTER
10
version 1.0
+ +
Knurled disc 2 stripes
1x
60°
1x
There are two diff erent knurled discs. One for each corner ending in a 5 (5-15-25-etc. degrees), which has one stripe round the outside, and one for each corner that ends in a 0 (0-10-20-etc degrees), which has two stripes round the outside.
There are two types of
knurled discs. Please
see education section.
Knurled disc 2 stripes Bolt M8x35Locknut M8
1x
A B
ride TWISTER
11
version 1.0
+
Handlebar short
1x
++
Axle plate1x
40x80_hexa 19
Bolt M5x6
1xMulti angle joint
1x
+
Profi le nut short
Bolt M8x25 Positioning block
1x
+
Positioning block
2x
A
B
C
ride TWISTER
12
version 1.0
belt pulley 28T
Handgrip
1x
A B
ride TWISTER
13
version 1.0
60°
+ +
Knurled disc 2 stripes Bolt M8x35
1xLocknut M8
1xKnurled disc 2 stripes
1x
A B
ride TWISTER
14
version 1.0
+ +
Bolt M8x251x
+
isc 1 stripe Bearing block 40x40_8
1x
+ +
T-Positioning block
6xParrellel clamp joint L-joint
Bolt M8x20 (low head)
1x12.60inch | 320mm
le 14.17inch | 360mm
Profi le 1x1x
Use the Allen key handle so you can tighten the bolt well.
M8x20 (low head)
All Infento block bearings have two bearings with a spacer in between. This ensures that you can e.g. put a bolt or a washer tightly against the block bearing without it breaking. A bearing cannot withstand lateral pressure very well; this is because a bearing consists of two washers with small balls locked in between.
A B
ride TWISTER
15
version 1.0
+ +
Locknut M81x Angle limiter
40º1x
Bolt M8x60
+
1xWasher M8-16pulley protection 28T
2x
double check!
A B
C D
ride TWISTER
16
version 1.0
Bolt M8x20 (low head)
+ + +
Multi angle joint Clamping par holes without threa
1x
+ +
T-Positioning block
6x1x11.02inch | 280mm
le 12.60inch | 320mm
Profi le 1xParrellel clamp joint L-joint
1x
M8x20 (low head)
Bolt M8x20
1x
The plastic parts of Infento are made using in-jection moulding technology where molten plastic is pressed under high pressure into a mould. A mould consists of steel blocks in which a shape is recessed.
A B
ride TWISTER
17
version 1.0
+ +
T-Positioning block
4xProfi le nut short
2xBolt M8x20 (low head)
2x
0.39” | 10 mm
A B
C D
ride TWISTER
18
version 1.0
+ +
Multi angle joint Clamping par holes without threa
1x
+
T-Positioning block
2xProfi le nut short
1xBolt M8x20
1x
0.39” | 10 mm
A
B
C
ride TWISTER
19
version 1.0
++
T-Positioning block
8xMulti angle joint
Clamping par holes without threa
1x
+
2x
+
Use the Allen key handle so you can tighten the bolt well.
Bearing block 40x40_Hexa 19
Driven rim
1x
le 3.15inch | 80mm
Profi le 1xBolt M8x20
A B
ride TWISTER
20
version 1.0
+ +
Knurled disc 2 stripes Bolt M8x35
1xLocknut M8
1xKnurled disc 2 stripes
1x
40°
A B
ride TWISTER
21
version 1.0
Parrellel clamp joint L-joint
+
5.51inch | 140mm le
6.30inch | 160mm Profi le
1x T-Positioning block
4x
+ + +
Multi angle joint Clamping par holes without threa
1x1xBolt M8x20 (low head)
1xBolt M8x20
1x
+
M8x20 (low head)
A B
ride TWISTER
22
version 1.0
+ +
Nut M8
1xBolt M8x25
1x
(low head)
Ducktail board extension + foam
2x
+
Profi le nut short1x
M8x25
+
Bolt M8x20
1x
A B
ride TWISTER
23
version 1.0
20°
+ +
Knurled disc 2 stripes Bolt M8x35
1xLocknut M8
1xKnurled disc 2 stripes
1x
A B
ride TWISTER
24
version 1.0
Profi le nut short
2xBolt M8x20
2x
+ +
Bolt M5x6
Ducktail board + foam
1x
A B
ride TWISTER
25
version 1.0
+ +
Washer M8-24
1x
+
Crank small left 1x
Pedal left1x
Bolt M8x20
3x
1mm
+
6.54inch | 166mm Axle 1x
A
B
C
ride TWISTER
26
version 1.0
Spacer 0.2inch | 5 mm
+ +
1x
0.2inch | 5 mm
Spacer0.04inch | 1 mm
1x 13 inchDriven wheel
1x
2 mm spacer
5 mm spacer
A B
ride TWISTER
27
version 1.0
+
Washer M8-24
1xPedal right
1x
+
Crank small right
1x
++
Bolt M8x20
3x
1mm
0.39inch | 10mm
Spacer0.08inch | 2 mm
1x
A B
C D
THANK YOU FOR READING ME!
TWISTER