+ All Categories
Home > Documents > TWS Sec_K

TWS Sec_K

Date post: 02-Jan-2016
Category:
Upload: wilmer-huaman-pasapera
View: 89 times
Download: 14 times
Share this document with a friend
Popular Tags:
151
K Tools & Safety Equipment
Transcript
Page 1: TWS Sec_K

K

Tools&

SafetyEquipment

Page 2: TWS Sec_K

K

Tools & Safety EquipmentContents Page

About Tools & Safety

© 1996 TELEWIRE SUPPLYK1

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Quality Policy

Tool belts, climbers, gaffs, hard hats and other tools or safetyequipment are, may be or may become subject to statute orregulation by either the federal, state or local authorities. Theemployer and the employee must ensure that the tools or safe-ty equipment are sufficient and proper for their intended use.

This section is designed as a buyer's guide only and is notintended to be a tool or safety equipment usage guide.Information regarding tool belts, climbers, gaffs and otherequipment is included solely as a convenience for the user ofthis section and is not intended to be used for a determinationof proper care or use.

Telewire Supply is dedicated to meeting the requirements ofour customers by providing Quality Products and Services on atimely basis.

Information on tool belts is provided courtesy of BashlinIndustries and is reprinted with their approval. Information onpole and tree climbers is provided courtesy of Klein Tools andis reprinted with their approval. Additional information on thecare or use of the materials in this section can be received fromthe manufacturer or the appropriate regulatory agency.

Item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page

How to Size a Belt . . . . . . . . . . . . . . . . . . . . . . . . . .K2

Lineman's Climbing Equipment . . . . . . . . . . . .K3-K15

Boots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K16

Equipment for Line Vehicles . . . . . . . . . . . . .K17-K25

Tool Pouches & Bags . . . . . . . . . . . . . . . . . . .K26-K33

Ladders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K34-K38

Screwdrivers . . . . . . . . . . . . . . . . . . . . . . . . . .K39-K42

Nut Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . .K43-K44

Wrenches . . . . . . . . . . . . . . . . . . . . . . . . . . . .K45-K46

Pump Pliers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K47

Bolt & Cable Cutters . . . . . . . . . . . . . . . . . . . .K48-K55

Long Nose Pliers . . . . . . . . . . . . . . . . . . . . . .K56-K59

Hammers . . . . . . . . . . . . . . . . . . . . . . . . . . . .K60-K61

Measuring Devices . . . . . . . . . . . . . . . . . . . . .K62-K64

Pocket Knives & Scissors . . . . . . . . . . . . . . .K65-K67

Hacksaws . . . . . . . . . . . . . . . . . . . . . . . . . . . .K68-K69

Heat Shrink Torches . . . . . . . . . . . . . . . . . . . .K70-K73

Fish Tapes & Conduit Rodders . . . . . . . . . . .K73-K76

Power Dart Blower . . . . . . . . . . . . . . . . . . . . . . . . .K76

Throwing Weight, Tool Box, Level . . . . . . . . . . . . .K77

In this section

Staple Guns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K78

Bit Braces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K79

Gloves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K80-K81

Hard Hats . . . . . . . . . . . . . . . . . . . . . . . . . . . .K82-K83

Flashlights . . . . . . . . . . . . . . . . . . . . . . . . . . . .K84-K85

Safety Equipment . . . . . . . . . . . . . . . . . . . . . .K86-K91

Power Tools . . . . . . . . . . . . . . . . . . . . . . . . . .K92-K98

Drill Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K99-K100

Crimpers & Prep Tools . . . . . . . . . . . . . . . .K101-K107

Cable Caddies . . . . . . . . . . . . . . . . . . . . . . . . . . .K108

Coring Tools . . . . . . . . . . . . . . . . . . . . . . . .K109-K115

Lashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K116

Construction Tools . . . . . . . . . . . . . . . . . . .K117-K130

LayUp Sticks . . . . . . . . . . . . . . . . . . . . . . . .K131-K135

Pulling Grips . . . . . . . . . . . . . . . . . . . . . . . .K136-K139

Breakaway Swivels . . . . . . . . . . . . . . . . . .K139-K140

Chain Hoists . . . . . . . . . . . . . . . . . . . . . . . .K140-K142

Fiberoptic Construction Tools . . . . . . . . . . .K143-K146

Shovels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K147

Anchor Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . .K148

Chemicals . . . . . . . . . . . . . . . . . . . . . . . . . .K149-K150

Page 3: TWS Sec_K

K

Tools & Safety EquipmentLineman’s Climbing Equipment

How to Properly Size a Lineman’s Body Belt

Proper sizing is one of the most important considerations inthe purchase of a lineman's tool belt. An improperly sizedbelt is uncomfortable and may cause an accident of injury.

Bashlin tool belts are measured by the "D" size, which is thedistance between the heels of the "D" rings. All lineman's toolbelts must be ordered according to the "D" size.

To Find Your “D” Size1.Locate the point where the heels of the "D" ring should

rest. This is approximately 4" down from the top of the hip bone.

2.Begin to measure from this point. Measure around thebuttocks to the same point on the opposite side.

When a properly sized tool belt is worn, the "D" rings will pointnearly straight ahead and the tongue adjustment will be in thecenter holes.

The tongue buckle section is sized in relation to the "D" mea-surement. There are nine holes in the tongue, one inch apart,allowing 8 inches of adjustment.

© 1996 TELEWIRE SUPPLY K2

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Belt Adjustment in Inches

D Size Center ToolInches Minimum Hole Maximum Loops

D18 32 36 40 2

D19 33 37 41 3

D20 34 38 42 3

D21 36 40 44 4

D22 37 41 45 4

D23 38 42 46 4

D24 40 44 48 4

D25 41 45 49 4

D26 42 46 50 4

D27 44 48 52 4

D28 45 49 53 4

Page 4: TWS Sec_K

DescriptionThis belt features a 5" cushion section for comfort with a nylonback and six ply tongue buckle section. It is lightweight, withstandard comfort features, Bashlin "S" D rings and all leathercushion. Weight: 3.75 lbs.

Tools & Safety EquipmentLineman’s Climbing Equipment

No. 88 Floridian Linemen’s BeltsBASHLIN

No. 160-N Shifting "D" Nylon Body BeltsBASHLIN

Description

Superior design and performance make this belt the industrystandard. It combines a padded, contour cushion section withflares for the shifting D rings and a 5-1/2" back. This belt givesexcellent support and climbing comfort. It is a practical belt withwearable quality which makes it economical. Weight: 5.5 lbs.

No. 1511-N Nylon Utility BeltsBASHLIN

Description

A familiar design in a shifting D nylon belt. The neopreneimpregnated nylon back is light, durable and flexible inextreme temperature ranges. The 5" leather cushion sectionis comfortable. The tongue and buckle is six ply nylon, andthe tool loops are leather. Weight: 4.5 lbs.K

© 1996 TELEWIRE SUPPLYK3

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. SizeBSH 006957 88 D18

BSH 006962 88 D19

BSH 006970 88 D20

BSH 006980 88 D21

BSH 006987 88 D22

BSH 006995 88 D23

BSH 007002 88 D24

BSH 150453 88 D25

BSH 115164 88 D26

BSH 150454 88 D28

Ordering Information

Order Mfg.No. No. SizeBSH 024059 1511N D18

BSH 033623 1511N D20

BSH 033624 1511N D21

BSH 033625 1511N D22

BSH 033626 1511N D23

BSH 033627 1511N D24

BSH 146805 1511N D25

BSH 007013 1511N D26

BSH 150455 1511N D28

Ordering Information

Order Mfg.No. No. SizeBSH 006971 160N D20

BSH 006988 160N D22

BSH 115108 160N D24

BSH 146962 160N D26

OUR BEST

SELLER

Page 5: TWS Sec_K

Tools & Safety EquipmentLineman’s Climbing Equipment

DescriptionGreen Nylon with Red Center

Flexible, lightweight pole strap is strong and durable. Consistsof 6 plies of nylon 1-3/4" wide, and withstands oil, creosote andsunlight degradation. Red nylon center is a wear indicator;remove from service when the red shows. Meets OSHA require-ments. Double lock both ends.

No. 76 Dakota Lineman’s BeltBASHLIN

Leather Pole Straps with Double Locks on Both EndsBASHLIN

DescriptionFeatures a six-ply nylon tongue and buckle with a uniquepadded suedelike contour cushion section. The 5-1/2" widesplit leather cushion is comfortable and makes it easier for thelineman who has trouble keeping his belt in position. Full shift-ing "D" saddle and semi-floating design. Weight: 3.75 lbs.

Nylon Pole Straps with Double Lock on Both EndsBASHLIN

Description

Made of 2 thicknesses of latigo leather with nylon insertedbetween the two plies. Uniform thickness is maintained andthe best wearing surfaces are exposed to the pole side at allstrap length adjustments. Sewn from end to end with nylonthread and hand finished. Thread is imbedded into the leather.Will stay soft and pliable year round. Meets OSHA require-ments. Size: 2" wide.

K

© 1996 TELEWIRE SUPPLY K4

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. SizeBSH 600208 76-20 D20

BSH 600209 76-21 D21

BSH 600210 76-22 D22

BSH 600211 76-23 D23

BSH 600212 76-24 D24

BSH 600213 76-25 D25

Ordering Information

Order Mfg. ShipNo. No. Size WeightBSH 150451 51N-2L 5'-6" 3.75 lbs.

BSH 150448 52N-2L 6' 3.75 lbs.

BSH 150447 53N-2L 6'-6" 4 lbs.

BSH 150446 54N-2L 7' 4 lbs.

Ordering Information

Order Mfg. ShipNo. No. Size WeightBSH 201648 78A-2L 6' 4.5 lbs.

BSH 201807 78B-2L 6'-6" 4.5 lbs.

BSH 201442 78C-2L 7' 4.75 lbs.

Page 6: TWS Sec_K

K

Tools & Safety EquipmentLineman’s Climbing Equipment

Lineman’s Fall Arrest SystemKLEIN

DescriptionKlein’s newest development in lineman’s equipment integratesvarious (OPE) occupational protective equipment (lineman’sbelt, fall-arrest harness, and positioning strap with locking snaphook) into a complete, self-contained fall arrest and positioningsystem for linemen. The system allows workers to comply withthe requirements of the August 9, 1994 revisions to OSHA’sregulations concerning fall protection.

Klein Lineman’s Systems consist of the following equip-ment (not available separately)

1. Fall Arrest Harness In the event of a fall, the full-body nylonharness distributes the user’s weight and any impact forcesover a larger area of the user’s body for greater comfort andsecurity. The system’s wide adjustment range allows for differ-ences in people’s height, weight and clothing thickness. Anadjustable pair of removable, synthetic lamb’s wool shoulderpads come standard with the system. The harness has a line-man’s belt with a positioning strap permanently attached to it.

2. Lineman’s Belt One of the semi-floating and four styles of full-floating belts are available. All belts have chrome-tanned leathercushions, and are equipped with two side D-rings for positioning.

3. Positioning Strap Three lengths of positioning straps areavailable. The abrasion-resistant Klein-Kord® strap is perma-nently attached to the lineman’s belt on either the left or rightside, as specified by the purchaser. The other end has a lockingsnap hook to attach to the D-ring on the other side of the belt.

Ordering Information & Procedure*

STEP 1 - Select the Belt Style Lineman’s system’s areavailable in a choice of semi-floating or full floating beltstyles, with various belt features such as size of pad andnumber/size of tool loops and snaps. All Klein Lineman’sbelts have chrome-tanned leather cushions for greatercomfort. Full-floating belts allow lateral movement of the D-rings during use. Semi floating belts only allow lateralmovement prior to wearing.

• Deluxe Full-Floating Body Belt Style # 5278

• Standard Full-Floating Body Belt Style # 5282

• Semi-Floating Body Belt Style # 5266

STEP 2 - Select the Proper Belt Size See page K2.

STEP 3 - Select the Proper Harness Size Harnesses areavailable in standard sizes of medium or large. The D-to-Dsize for your belt normally determines the harness size (seetable). If a different size is needed, alter this part of the cat-alog number.

D-to-D Size Harness Size

Up to 26 inches Medium

27-30 Inches Large

STEP 4 - Select the Proper Positioning-Strap Length EachLineman’s System has a permanently-attached positioningstrap that is available in standard lengths of 6', 7' or 8' (1.8,2.1 or 2.4m) Select lengths available on request.

STEP 5 -Select Positioning-Strap Attachment Point Thepositioning strap is permanently attached to either the left orright side of the lineman’s belt in the system. Your choiceshould be based on your usual work situation and your pref-erence of connecting the snap hook to one particular side. Ifyou are left handed, for instance, you might favor a right-side attachment point.

The catalog number used to order a Lineman’s System ismade up of specific parts. Each part of the number refers to acomponent or component size. All system catalog numbershave the prefix "LS". The following is a typical example of a cat-alog number (LS5278-24-M-7-L).

LS 5278 - 24 - M - 7 - L

* Please consult your Telewire sales representative for complete ordering instructions. All fall arrest systems are custom built - order carefully!NO RETURNS

© 1996 TELEWIRE SUPPLYK5

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

PositioningSystem Belt D-to-D Harness Positioning strap attachmentPrefix Style Size Size strap length (left or right)

Page 7: TWS Sec_K

Tools & Safety EquipmentLineman’s Climbing Equipment

Lineman’s Holster 111-HSBASHLIN

Holster for Bell Wrenches

Lineman’s Holster 111-HLSBASHLIN

K

© 1996 TELEWIRE SUPPLY K6

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Description

111 Series for riveting on linemen’s belts (double leather back).Do not attach electrician holsters to linemen’s belts. Use onlylinemen’s holsters on line belts. Rule pocket on all holsters ismade for wide rule. Snap is designated by the letter "S" in theholster number.

Ordering Information

Order Mfg.No. No. Description WeightBSH 007327 111-HS For pliers, rule, screwdriver, 1 lb.

knife or wrench.

Ordering Information

Order Mfg.No. No. Weight.BSH 600182 111BWH 6 oz.

KLN 008311 (Order Number For 5/8" HDW Bell Wrench)

Ordering Information

Order Mfg.No. No. Description WeightBSH 007326 111-HLS For pliers, rule, screwdriver, 1.25 lbs.

knife, Channellocks or wrench.

Description

111 Series for riveting on linemen’s belts (double leather back).Do not attach electrician holsters to linemen’s belts. Use onlylinemen’s holsters on line belts. Rule pocket on all holsters ismade for wide rule. Snap is designated by the letter "S" in theholster number.

Page 8: TWS Sec_K

DescriptionMade of No. 8 heavy brown canvas with 1/4" rope ring sewninto top for extra rigidity. Snaps provided on loops for easyattachment to belts up to 3" wide. Ventilating eyelet in bottom.Overall size: 9" x 10". Top opening size: 8" x 3".

Tools & Safety EquipmentLineman’s Climbing Equipment

Handline ClipKLEIN

All Purpose BagKLEIN

Canvas Utility BagKLEIN

K

© 1996 TELEWIRE SUPPLYK7

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionHandline Clamp with thong. Tension of between 8 and 12 lbs.releases the handline should it snag. Slotted for easy attach-ment to belt.

Ordering Information

Order Mfg.No. No. SizeKLN 007419 5133 10-1/2" Wide (27 cm)

Ordering Information

Order Mfg. ShipNo. No. Weight.KLN 007297 5142 12 oz.

KLN 026864 5142P with inside pocket 12 oz.

DescriptionDurable leather bag, ideal for carrying loose tools and smallparts. Large loops for attaching to belts up to 3" wide.

Ordering Information

Order Mfg. ShipNo. No. Size Weight.KLN 023108 5146 9" x 3" x 8" 10 oz.

Page 9: TWS Sec_K

Tools & Safety EquipmentLineman’s Climbing Equipment

DescriptionMade of canvas with a reinforced bottom. Belt attachment isdone by two straps joined by snaps and "D"s.

Bolt & Nut Bag - 26GBASHLIN

Bolt & Nut Bag - 25PSBASHLIN

DescriptionA soft Leather bag with snap closure & leather attachmenttongs 8-1/2" x 9".

Bolt & Nut Bag - 25ABASHLIN

DescriptionA wide opening canvas bag with leather reinforced bottom &snap attachment 8" x 8" x 12".

K

Ordering Information

Order Mfg.No. No. WeightBSH 007320 26G 9 oz.

© 1996 TELEWIRE SUPPLY K8

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. WeightBSH 104874 25A 12 oz.

Ordering Information

Order Mfg.No. No. WeightBSH 007315 25PS 10 oz.

Page 10: TWS Sec_K

K

Tools & Safety EquipmentLineman’s Climbing Equipment

Worker SafetyPOLE AND TREE CLIMBERS

© 1996 TELEWIRE SUPPLYK9

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Pole and tree climbing equipment is to be used ONLY by indi-viduals who are qualified and properly trained to use this equip-ment. Improper use of climbing equipment can cause seriousinjury or death.

Climber and Gaff Inspection Procedures1. Climber straps and pads

Make sure straps and pads are free of burns, cuts, brokenstitches or excessive wear. Since leather is subject to deterio-ration, carefully check all leather for cracking, wearing thin, tear-ing, weakening, chemical attack or other signs of deterioration.

2. Rivets, buckles and other metal partsCheck that rivets are not bent, loose or missing. Check that allbuckles are not distorted or cracked, tongue does not bind onbuckle and buckle holes are not damaged. Also check splitring, leg iron and steel sleeve for signs of excessive wear ordamage.

3. Check gaff with gaff gaugeAgaff gauge should be used to check proper width, thickness andpoint profile of climber gaffs before each use. Specific instructionson use of the gaff gauge are enclosed with the product.

4. Check gaff sharpness with the "plane test"Step 1:Place climber with point of gaff downward and upper straploop resting against a board or pole. Hold the leg iron paral-lel to the wood surface with the stirrup vertical. Push theclimber horizontally in the direction of the gaff without anydownward pressure except the weight of the climber.Step 2:If the gaff buries itself in the wood within a few inches of itsstarting position and can no longer be moved forward, thegaff is properly sharpened. If the gaff merely slips, slides orplows a shallow groove in the wood, it is NOT properly sharp-ened and should be replaced or resharpened. A resharpenedgaff must be tested for proper width, thickness and point pro-file, and must also pass the "plane test" before use.

5. Destroy and replace all worn or damaged OPE equipment.If evidence of excessive wear, deterioration or mechanical mal-function is observed, replace the equipment immediately.Never work with worn or damaged OPE equipment. Usingdamaged or worn equipment can cause serious injury or death.

6. The inspector is the most important part of anyinspection procedure.Check all equipment thoroughly and follow all safety proce-dures and guidelines. Do not take any shortcuts.

Important note:OSHA specifies that all employers covered by the OccupationalSafety and Health Act are responsible for inspection and main-tenance of all tools and equipment used by employees -whether owned by the employees or the company. Personal-protective equipment should be inspected before each use andremoved from service if signs of wear or damage are found.

Should any unusual conditions be noted during the inspectionwhich are not specified here, do not use the suspect equipmentuntil a qualified individual makes a decision on its usability.

Maintenance ProceduresClean and maintain equipment in accordance with recom-mended practice. Wash nylon only in warm water and mildcleanser. Avoid harsh chemical agents such as de-greasingcompounds, turpentine, paint thinner, gasoline and other sol-vents. Allow nylon objects to dry naturally. Do not use heat tospeed up the process.

Maintain or replace gaffs as instructed in product installations topreserve proper width, thickness, point profile and sharpness.

Source: Klein Tools, Inc.

Page 11: TWS Sec_K

K

Tools & Safety EquipmentLineman’s Climbing Equipment

Worker SafetyPOLE & TREE CLIMBERS

© 1996 TELEWIRE SUPPLY K10

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Cautions: Pole and Tree Climbers• Climbing equipment is for use by properly trained

professionals only.

• Use climbing equipment only for the specific purpose forwhich it is designed and intended.

• Always visually check that all buckles are properly closedbefore use.

• Before each use check that:1. gaffs are free of dents, gouges or scratches2. gaffs have proper width, thickness,point profile and sharpness3. resharpen or discard and replace gaffs if they fail inspection.

• Before each use check that:1. climber straps and pads are free of burns, cuts, broken

stitches or excessive wear2. rivets are not bent, loose or missing, 3. buckles are not distorted or cracked, tongue does not bind

on buckle and buckle holes are not damaged, 4. remove from service, destroy and discard item if it fails

inspection and replace immediately.

• Never punch holes in or alter a strap or climber.

• For leather straps: leather is subject to deterioration bycracking, wearing thin, tearing, weakening and chemicalattack. Carefully maintain with neatsfoot oil or equivalent.Inspect straps for these conditions before each use. Removefrom service, destroy and discard strap if it shows any ofthese conditions and replace immediately.

• While climbing, avoid gaff contact with metal, i.e. pole IDtags, nails, poster staples, pole hardware

• Poles are NOT all alike. Different wood species, climate, poleage, and preservative treatments (Creosote, Penta, CCA) affectclimbability, resulting in significant differences in gaff penetration.Visually check gaff penetration with your full weight on theclimber before any climb. If penetration is shallow, useextreme caution. The gaff could "cut-out", or the increasedstress could lead to tip breakage. For proper penetration, the min-imum underside length of a pole climber gaff is 1-7/16" (37 mm).

• Trees are NOT all alike. Different species and bark thicknessaffect climbability. Visually check gaff penetration as describedfor pole climbers before any climb.For proper penetration: 1. use a tree climber gaff with a minimum underside length of

2-1/2" (64 mm),2. when bark thickness measures more than 2-1/2" (64mm),

make sure gaff has adequate length for proper penetrationof wood under the bark.

• After climbs, remove climbers to avoid gaff damage fromhard surfaces or each other while walking.

• Use gaff guards to protect gaff tips between uses.

• Limiting gaff replacement on climbers to two times is highlyrecommended.

• Employer - instruct employee as to proper use and warn-ings before use of all equipment.

• Read, understand and follow all information attached toand/or packed with climber before use.

WARNING Inspect leather straps for any deterio-ration before each use, i.e. cracking, wearing thin, tear-ing, weakening, chemical attack. Maintain with neatsfootoil or equivalent. Remove from service, destroy and dis-card strap if it does not pass inspection.

CAUTION All pole and tree climbers are for use bytrained and qualified people only.

CAUTION For your protection, we recommendthat a maximum of only two sets of replacement gaffs beused on replacement-gaff climbers.

Source: Klein Tools, Inc.

!

!

!

Page 12: TWS Sec_K

Tools & Safety Equipment

Replacement GaffsBASHLIN

Adjustable Climbers-BD16BCBASHLIN

K

DescriptionThe BD14 is Bashlin’s aluminum alloy offset climber with areplaceable, forged steel gaff. This lightweight climber reducesfatigue and adds climbing comfort. Comparable steel climbersweigh 30% more. The aluminum alloy construction sacrificessome wearing qualities.

Ordering Information

Order Mfg.No. No. Description Weight.

BSH 150463 BD14-1N Nylon bottom straps attached 4.25 lbs.

BSH 150462 BD14-2N Nylon top & bottom straps attached 4.75 lbs.

BSH 600172 BD14-4N Nylon top & bottom straps & #130 pads 5.5 lbs.

BSH 600174 BD14-5N Nylon top & bottom straps & #140 pads 5.75 lbs.

DescriptionThe BD16C steel climber has a replaceable gaff and twistedshank.The twisted shank lies flatter on the leg for more comfort.

Ordering Information

Order Mfg.No. No. Description Weight.

BSH 150461 BD16BC-2 Nylon top & bottom straps attached 6 lbs.

BSH 600176 BD16BC-5 Nylon top & bottom straps & #140 pads 7 lbs.

SpecificationsOnly use Bashlin Replacement Gaffs in Bashlin Climbers.

Ordering Information

Order Mfg.No. No. Description

BSH 007152 14 Pole gaffs w/screws (1pr.) for BD-14 or 16 climbers

BSH 007153 14-T Tree gaffs for BD-14 and BD-16 climbers

Lineman’s Climbing Equipment

Adjustable Climbers-BD14BASHLIN

© 1996 TELEWIRE SUPPLYK11

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Page 13: TWS Sec_K

K

Tools & Safety EquipmentLineman’s Climbing Equipment

1972AR Series Pole ClimbersKLEIN

© 1996 TELEWIRE SUPPLY K12

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionFurnished with Klein No. 8210 pads and a choice of calf and ankle straps.Pad size is 8" x 8" (203 x 203mm). The climbers below are available in twosize adjustment ranges, adjustable in 1/4" increments.

Ordering Information

Order Mfg. SizeNo. No. Description Adjustable

KLN 007131 CN1972AR equipped with No. 8210 pads, 15"-19"(381-483mm)No. 5301-18 nylon calf straps, andNo.5301-20 nylon ankle straps

KLN 021419 CN1972ARL equipped with same straps 17"-21"(432-533mm)and pads as CN1972AR

DescriptionPole climbers only, identical to CN1972AR Series, but without pads andstraps. Components consist of steel sleeve, leg iron, split ring and gaff. Todetermine size needed, measure from instep to 1" (25mm) below knee.

Ordering Information

Order Mfg. SizeNo. No. Description Adjustable

KLN 007129 1972AR Climbers only, no straps or pads included 15" to 19"

Replacement gaffs

KLN 007156 72 Pair of 1-1/2" gaffs for pole climbers only

KLN 023756 07 Pair of 2-3/4" gaffs for tree climbing

Only use Kline replacement gaffs in Kline Climbers

Page 14: TWS Sec_K

K

Tools & Safety EquipmentLineman’s Climbing Equipment

Nylon Climber Strap ReplacementBASHLIN Description

Bashlin’s split ring can be attached to climbers by removing theoriginal ring and threading the split ring through the hole (min.of 3/16" dia.) in the climber lug. All sold in pairs.

DescriptionThese neoprene-impregnated nylon straps may be used withany Klein pole or tree climbers. All sold in pairs.

Nylon Climber Strap ReplacementsKLEIN

Ordering Information

Order Mfg.No. No. Description Size WeightBSH 007378 85N Top straps 1-1/16" x 24" 5 oz.

BSH 020415 89N Slit ring and 2 piece bottom strap 1-1/16" x 28" 11 oz.

BSH 007380 86N 1 piece bottom straps 1-1/16" x 28" 7 oz.

BSH 007382 87N 2 piece unassembled bottom straps 1-1/16" x 28" 10 oz.

© 1996 TELEWIRE SUPPLYK13

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Description Size WeightKLN 007369 530-18 Top straps 1" x 22" 6 oz.

KLN 007370 530-19 Top straps 1" x 26" 6 oz.

KLN 007372 530-21 Top straps 1-1/4" x 22" 6 oz.

KLN 007374 530-23 Split ring & 2 piece bottom strap 1-1/4" x 24" 11 oz.

KLN 007371 530-20 Split ring & 2 piece bottom strap 1" x 24" 11 oz.

Page 15: TWS Sec_K

K

Tools & Safety EquipmentLineman’s Climbing Equipment

DescriptionThis "T" shaped pad protects the shin and the calf. Theleather lugs are securely riveted for long wear. Padded, sold in pairs.

DescriptionThis is the original "spur-stay" climber pad. It is designed toreduce kick-back and twisting of the shank. The insert holdsthe the climber for comfort and better gaff penetration. It isan excellent choice for the lineman who climbs occasionally.With a angled metal section sold in pairs.

Wing Climber PadsBASHLIN Description

140DS Pads - The wing pad holds the shank more securelythan the other leather pads. The climber shank fits inside thepad, reducing movement and adding comfort. With paddingsold in pairs.

"T" Climber PadsBASHLIN

Ordering Information

Order Mfg.No. No. WeightBSH 007282 140-DS 1.25 lbs.

© 1996 TELEWIRE SUPPLY K14

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Description Weight

BSH 007276 105BC Fits Bashlin BA14 climbers 2 lbs.

BSH 007274 105AC Fits Bashlin BA16 climbers 2 lbs.

KLN 007273 8210 Fits all Kline climbers only 2 lbs.

Ordering Information

Order Mfg.No. No. WeightBSH 007284 150 TS 15 oz.

OUR BEST

SELLER

Metal Spur-Stay PadsBASHLIN

KLINE

Page 16: TWS Sec_K

DescriptionTools and instructions in a compact case. Consists of correctfile and handle, gauge, finishing stone and instructions.

Tools & Safety EquipmentLineman’s Climbing Equipment

"L" Climber PadsKLEIN

Gaff Protector & Gauges

DescriptionRight and left L-shaped pads of high-grade Latigo leather,cushioned with rubberized horsehair.

Gaff Shaping KitBASHLIN

K

Ordering Information

Order Mfg.No. No. SizeKLN 007273 8210 8" x 8"

© 1996 TELEWIRE SUPPLYK15

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Size WeightBSH 007168 27 10" x 4" x 1-1/2" 12 oz.

Ordering Information

Order Mfg.No. No. DescriptionBSH 007163 #2 For replaceable Gaffs with velcro fastener.

No snaps, buckles or tie strings.

BSH 007162 #1 For Non - replaceable Gaffs

Gaff Gauges

BSH 007159 #5 Gauge only

KLN 007160 KG-1 Gauge only

Page 17: TWS Sec_K

K

Tools & Safety EquipmentLineman’s Climbing Equipment

Highliner BootsWEST COAST Ordering Information

10" high 10" highNo. 9710 No.9710

Size D width E width Weight7 WST 602736 WST 201958 7 lbs.

7-1/2 WST 122161 WST 201956 7 lbs.

8 WST 007035 WST 201957 7 lbs.

8-1/2 WST 007039 WST 122170 7 lbs.

9 WST 007045 WST 122176 7 lbs.

9-1/2 WST 007049 WST 122180 7 lbs.

10 WST 007054 WST 122181 7 lbs.

10-1/2 WST 007059 WST 122184 7 lbs.

11 WST 007063 WST 122186 7 lbs.

11-1/2 WST 122189 WST 202060 7 lbs.

12 WST 104140 WST 122194 7 lbs.

DescriptionDesigned specifically for professional linemen. Hand-crafted,with heavy steel shank in the arch for extra support, a steel sideplate to protect the sole of the boot, and a leather side patch toprotect the vamp at the ball of the foot.

Uppers of full grain heavy 6 - 6-1/2 ounce leather, with full gussettongues, solid brass studs and eyelets, full leather in soles andmid soles, slip-in washable cushion inserts and #430 Vibram® OilResistant soles and heels. Soles are double stitched.

All stocking sizes are black. Redwood available by specialorder. Other sizes and widths can be special ordered. Made inthe USA. Custom ordered boots are non returnable.

16" high 16" highNo. 9710 No.9710

Size D width E width Weight7 WST 043048 WST 202061 8 lbs.

7-1/2 WST 007068 WST 202062 8 lbs.

8 WST 007071 WST 007073 8 lbs.

8-1/2 WST 007075 WST 007077 8 lbs.

9 WST 007080 WST 007082 8 lbs.

9-1/2 WST 007085 WST 007087 8 lbs.

10 WST 007090 WST 007092 8 lbs.

10-1/2 WST 007094 WST 007096 8 lbs.

11 WST 007099 WST 007101 8 lbs.

11-1/2 WST 020561 WST 022432 8 lbs.

12 WST 023346 WST 147455 8 lbs.

Ordering Information

Order Mfg.No. NoSFT 153150 L8262

Boot Covers

© 1996 TELEWIRE SUPPLY K16

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionDisposable polyethylene boot covers protect work shoes andboots from spills and debris and help keep floors clean andfree of outside contaminants. Made of sturdy 3 mil. polyeth-ylene, 18" high with top ties. Sold in boxes of 50. One sizefits all.

Page 18: TWS Sec_K

K

Tools & Safety EquipmentEquipment for Line Vehicles

Boom StrapsBASHLIN

DescriptionThis device provides a lanyard attachment point on the boom.The nylon strap passes through a circle "D" that is padded toprotect the boom. Also, a friction buckle helps provide for quickand easy adjustment. Lanyards and aerial belts must beordered separately.

DescriptionLanyards feature forged double action locking snaps and nylon,polypropylene or nylon web construction. Other non-returnablelengths are available on request.

Lanyards

Ordering Information

Order Mfg.No. No. WeightBSH 007363 703 1.25 lbs.

© 1996 TELEWIRE SUPPLYK17

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Description WeightKLN 146273 87417 1/2" x 4' Nylon Filament rope 2.50 lbs.

KLN 146272 87431 1" x 5' Nylon web strap 3 lbs.

WARNING When working with lanyard, keep theamount of slack between the anchor point and the fall-arrest belt or harness at an absolute minimum to reduceimpact force in the event of a fall.

WARNING Never use an aircraft-cable lanyard by itself forfall protection. Always use a deceleration device with aircraft cable.

WARNING DO NOT use aircraft-cable lanyardsnear energized equipment.

WARNING Do not rely on the feel or sound ofsnap hook engaging. Always check visually for properengagement of the snap hook.

!

!

!

!

Page 19: TWS Sec_K

K

Tools & Safety EquipmentEquipment for Line Vehicles

Full Body HarnessKLEIN

DescriptionFall-Arrest Harness with Leg, Seat, Chest, & Shoulder Straps

This comfortable, lightweight, full-body harness is designedto arrest free falls and distribute impact forces over thighs,pelvis, waist, chest and shoulders as required by OSHA. Theleg, seat waist, chest and shoulder straps provide extra com-fort in normal use as well as support before, during and aftera fall. Shoulder, chest and waist strap colors contrast with legand seat colors to simplify putting the harness on. Harnessis equipped with one adjustable, forged, circle D-ring at backfor attaching a fall-arrest connecting device. The harness ismade of tough 1-3/4” (44MM) Type 13, or equivalent, nylonwebbing. Shoulder straps have friction slide adjusters foroptimum fit. Both the waist and chest straps feature friction-style buckles for positive securement. Leg straps havetongue buckles with grommeted holes.

Always use Fall Protection if there is a risk of fall

Although OSHA regulations generally require worker to uti-lize fall protection when exposed to a fall of six feet or more,we strongly recommend using a fall-arrest protection whenworking at any elevated position. When unsure or in doubt,contact your regional OSHA office. In addition, as of 1/1/98,OSHA will prohibit body belts from being used as part ofthe fall-arrest system.

Know the Appropriate regulations

Learn about the types of protective equipment and systemswhich must be used on the job. OSHA requires employers toknow and follow the OSHA regulations pertaining to theirindustry and to provide a workplace free from hazards thatmight cause injuries. OSHA provides consultation assistancein training and implementation. If you have any questionsor any doubt as to what regulations apply to you or whatsafety equipment is required, contact your regionalOSHA office.

Ordering Information

Order Mfg.No. No. Size

KLN 201900 87020 Medium

KLN 201902 87021 Large

KLN 201901 87022 Extra Large

KLN 201919 87023 2X Large

© 1996 TELEWIRE SUPPLY K18

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Page 20: TWS Sec_K

DescriptionDesigned to be attached to aerial baskets. Heavy duty No. 6canvas bucket has 15 pockets for tools. Furnished with twoABS hooks.

DescriptionDesigned to carry the small hand tools a lineman ordinarilycarries in his tool belt. There are individual pockets to carrypliers, wrenches, hammer, screwdrivers as well as pocketsfor some of the popular size sockets. Bag also has a smallbolt and nut bag section - 5/8" hooks (2) included.

Made of heavy canvas with a reinforced masonite bottom.Frame and hooks made of non-conductive material.

K

Tools & Safety EquipmentEquipment for Line Vehicles

No. 708 Aerial Basket Tool CarrierBASHLIN

Outside Tool Tray

No. 706 Aerial Basket Tool BagBASHLIN

DescriptionTool boards are made of ABS. This light, durable material doesnot fray or flake and has superior cold weather characteristics.

These boards are built and arranged with the worker in mind.They save precious space in the basket, yet keep the tools in ahandy position.

Tools not included. Lip size 2-1/2"x 3/4".

Tool BucketKLEIN

Ordering Information

Order Mfg.No. No. Size Description

BSH 007549 708 18" x 20" Comes with canvas nut & bolt bag

© 1996 TELEWIRE SUPPLYK19

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Description/Size WeightBSH 007547 706 14" L x 7" W x 10" H 3 lbs.

BSH 007579 712 5/8" dia. replacement hook 4 oz.

Ordering Information

Order Mfg.No. No. Description/Size WeightKLN 007536 5144 14" L x 8" W x 10" H 3 lbs.

KLN 044174 5144H Replacement hook 4 oz.

DescriptionThis is a light compact tray, ideal for nuts, bolt, etc. The mounting bracket is adjustable.

Ordering Information

Order Mfg.No. No. Description Size Weight

BSH 727-L 727-L With liner 14" L x 6" W x 7-1/2" H 9 lbs.

BSH 727-O 727-O Without liner 14" L x 6" W x 7-1/2" H 9 lbs.

Page 21: TWS Sec_K

K

Tools & Safety EquipmentEquipment for Line Vehicles

Features• Steel cylinder• Heavy duty all metal valves and siphon tubes• Squeeze grip operation• Replaceable seals• Interchangeable parts• Corrosion resistant finishes• Dry chemical; regular-BC; approved to -65°F.

Emergency Warning Triangle

Safety Flares

DescriptionEmergency warning triangle with each leg made of fluorescentorange day-glo material with hi-intensity reflective area for nighttime warning. Triangle disassembles and folds flat in its own stor-age case. Meets or exceeds Federal Specification: FMV55-125

Portable Fire Extinguisher

Ordering Information

Order Mfg.No. No. DescriptionSFT 140982 99 ET Set of three triangles and case

© 1996 TELEWIRE SUPPLY K20

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionRed flare with spike. Sold in quantities of 12.

Ordering Information

Order Mfg.No. No. Average Flare TimeSFT 007457 2715 15 minutes

SFT 007459 2720 20 minutes

SFT 007460 2730 30 minutes

Ordering Information

Order Size/ UL Coat GuardNo. Description Capacity Rating Weight Approved BracketFXT 021250 Fire Extinguisher 2-1/2 lbs. 10B:C 5-1/2 lbs. yes vehicle mount

FXT 007567 Fire Extinguisher 5 lbs. 10B:C 9 lbs. yes wall mount

Page 22: TWS Sec_K

DescriptionMade of 5/16" four strand polypropylene rope, spliced to eye ofsnap hook. Red and white strand for high visibility. 75" long.Maximum safe load: 250 pounds. This is not a occupationalprotective device. Not for human support.

Tools & Safety EquipmentEquipment for Line Vehicles

Wheel Chock - Wood & Rubber

Combo Hitch 1110JACKSON

Polypropylene Hand Lines with Snap HookKLEIN

DescriptionSimple and easy to use strong enough for the job. Max. 3500lbs. Now you only need one hitch for or your pulling needs.2" square (Reese type) with 2 pin holes and up to 4 types ofBall Hitches.

• Pintle Hitch - for pulling construction equipment for large trailers

• Standard Ball Hitch - 1-7/8" and 2" ball• Pin Hitch - for pulling wagons (pin optional)• Optional - 2-1/2 ball will fit pin hitch hole J2

K

Ordering Information

Order Mfg.No. No. Description WeightJKS 201953 1110 welded & hardened steel 10 lbs.

zinc plating

© 1996 TELEWIRE SUPPLYK21

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionWOOD Block for chocking truck wheels. Made from severalpieces of oak with tongue and groove joints, laminated underhigh pressure with waterproof glue. Approximate size 10" L x 9"W x 5/4" H. Metal handle is thru-bolted to the block.

RUBBER Made of laminated rubber tightly compressed. It hasa low center of gravity which eliminates tipping and slippage.1/4" x 24" poly rope included. 100% effective on any size tire.Ends painted a highly visible yellow.

Ordering Information

Order Mfg.No. No. Description WeightGMP 007555 07280 Wood 9 lbs.

SFT 022996 RB-1 Rubber 10 lbs.

Ordering Information

Order Mfg.No. No. DescriptionKLN 044116 1804-60 With 443A snap hook

Page 23: TWS Sec_K

K

Tools & Safety EquipmentEquipment for Line Vehicles

Plastic Water CoolersDescriptionDouble-wall construction of high-density polyethylene with rigidurethane foam insulation helps to keep contents cold. Lidsscrew on tightly. Recessed faucet with double gasket lockingsystem to help prevent clogs or leaks. Splash seal helps pre-vent spills. The 3 and 5 gallon models feature a snap-in drink-ing cup holder.

Water Cooler Accessories

Description4 oz. paper cups for 4 oz. cup dispenser. Case quantity is2,500 (25 packs of 100).

Ordering Information

Order Mfg.No. No. Gallons ColorGOT 021319 1692-01-11 2 orange/white

GOT 150467 1683-01-11 3 orange/white

GOT 020967 1685-01-11 5 orange/white

© 1996 TELEWIRE SUPPLY K22

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. ForNo. No. Gallons Height Diameter Weight

GOT 007561 3037 3 10" 11-1/4" 6 lbs.

GOT 007562 3057 5 10" 12-3/4" 9 lbs.

Truck Mounting Brackets for Water Coolers

Description4 oz. cup dispenser, white

Ordering Information

Order Mfg.No. No.GOT 150466 8250

Ordering Information

Order Mfg.No. No.GOT 150465 0154-01-01

Page 24: TWS Sec_K

K

Tools & Safety EquipmentEquipment for Line Vehicles

First Aid Kits

DescriptionElectronic back up alarm with heavy duty die-cast housingdesigned for emergency and maintenance vehicles, construc-tion equipment, trucks, buses, lift trucks and utility vehicles.Less than 1/2 amp, 12 through 36 VDC> Approximately 60beeps per minute. Decibel rating factory pre-set at 102 dBA ±4dBA. 3" H x 2" D x 4-1/2" W.

Back-Up AlarmsSTAR WARNING

Ordering Information

Order Mfg.No. No. DescriptionFAD 023335 610-112 10 unit kit

FAD 023334 616-121 16 unit kit

FAD 023341 624-133 24 unit kit

© 1996 TELEWIRE SUPPLYK23

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

10 16 24Contents Unit Kit Unit Kit Unit Kit

Steel unit cabinet 1 1 1

Strips, 1" x 3" unit 16's 2 3 3

X-tra large bandage, 6's 1 2 2

Tape, spool 1/2" x 5 yds 0 0 1

Compress bandage, 4" unit 1 2 3

Gauze compress unit, 24" x 72" 0 1 2

Gauze pad 3" x 3", unit 0 0 1

Bandage, gauze 4" x 6 yds 0 1 1

Triangle bandage, double box 1 1 2

Burn cream. 1/8oz. foil pk., 6/bx 1 1 1

PVP wipes, 10's 1 2 3

Cold pack, small, unit 0 0 1

Tourniquet and forceps unit 1 1 1

Ammonia inhalants, 10/box, unit 1 1 1

First aid instruction card 1 1 1

Latex gloves, 1pair/bag 1 2 3

Ordering Information

Order Mfg.No. No.SFT 145527 60-102

Page 25: TWS Sec_K

Tools & Safety EquipmentEquipment for Line Vehicles

Electronic StrobeTRI-LITE

Magna LightLARSON ELECTRONICS

DescriptionProduces more visible light than any sealed beam, with 75flashes per minute. Current draw is 2 amps at 12 to 48 VDCand 117 AC. Maintenance-free light ideal for utility trucks,tow vehicles, off-road construction equipment and emer-gency vehicles. Amber color.

Model RF-6 Roto FlashTRI-LITE

DescriptionMagnet base 100 lb. pull holds firmly to any ferrous metal. Comes standardwith 12 volt cigarette style plug built in handle. HML-3 uses halogen bulb.

K

Ordering Information

Order Mfg.No. No. Size WeightTRI 060831 ST-1 6.5" H X 5.5" D 5 lbs.

© 1996 TELEWIRE SUPPLY K24

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionThe standard warning light of the industry, a heavy duty two-sealed beam revolving light ideal for utility trucks, tow vehicles,construction equipment and emergency vehicles. Amber color.RF-MAG converts the RF-6 to magnetic mount with cigarettelighter plug/cord included.

Ordering Information

Order Mfg.No. No. DescriptionTRI 007462 RF-6 Roto Flash

TRI 202067 RF-MAG Magnetic Base

Ordering Information

Order Mfg. Candle Beam Beam Power BulbNo. No. Power Length Width Drain LifeLRS 201914 HML-1 28,000 80' 60' 2.5 Amp Hr. 300 Hr.

LRS 201915 HML-2 90,000 3500' 40' 2.5 Amp Hr. 100 Hr.

LRS 201916 HML-3 200,000 3 miles 20' 6.5 Amp Hr. 25 Hr.

Page 26: TWS Sec_K

K

Tools & Safety EquipmentEquipment for Line Vehicles

Redi-Line Electric Generator Redi-Line Electric GeneratorPACIFIC-SCIENTIFIC PACIFIC-SCIENTIFIC

DescriptionDC to AC 500 to 900 WattsGet 120 volt true sine-wave AC power from battery or DCpower source. Energy saving feature results in generator run-ning only when power is required (power tool trigger or appli-ance switch). Constructed from durable materials. Can bemounted in any position with minimum space required. No airpollution. Operates quietly in confined areas. Built-in circuitbreaker prevents damage from overloads. Generator hascapacity to deliver surge-current above its rated output whenmomentary extra starting power is needed. Incorrect connec-tion to generator terminals will not damage unit. Acceptableambient temperature of -30°F(-34°C) to +130°F (+54°C).

SpecificationsInput

DC Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Output

Watts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 VACAmps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hz

Battery RecommendationsType . . . . . . . . . . . . . . . . . . . . . . . deep cycle/marineCapacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Amp

Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . 8 AmpsElevation Sensitivity . . . . . . . . . . . . . . . . . . . . . . . noneLength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-3/8"Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1/8"Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5/8"Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 lbs.

Ordering Information

Order Mfg.No. No.RNC 024651 DA-12A-500Variance from 120V, 60 Hz is dependent on load size and DC input voltage

© 1996 TELEWIRE SUPPLYK25

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionDC to AC 1600 WattsGet 120 volt true sine-wave AC power from battery or DCpower source. Energy saving feature results in generator run-ning only when power is required (power tool trigger or appli-ance switch). Constructed from durable materials. Can bemounted in any position with minimum space required. No airpollution. Operates quietly in confined areas. Built-in circuitbreaker prevents damage from overloads. Generator hascapacity to deliver surge-current above its rated output whenmomentary extra starting power is needed. Incorrect connec-tion to generator terminals will not damage unit. Acceptableambient temperature of -30°F to +130°F (-34°C to +54°C).

SpecificationsInput

DC Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Output

Watts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1600Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 VAC Amps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Hz

Battery Recommendations Type . . . . . . . . . . . . . . . . . . . . . . . .deep cycle/marine Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Amp

Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . .18 AmpsElevation Sensitivity . . . . . . . . . . . . . . . . . . . . . . .noneLength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-3/4"Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5/8"Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1/2"Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 lbs.

Ordering Information

Order Mfg.No. No.RNC 153467 DA-12L-1600 Variance from 120V, 60 Hz is dependent on load size and DC input voltage

Page 27: TWS Sec_K

Tools & Safety EquipmentTool Pouches & Bags

DescriptionNo. 5166. Soft and pliable moisture resistant pouch. Has twolarge gusseted utility pockets, two screwdriver pockets, ham-mer loop, three plier pockets and one chain tape thong. Tunnelloop for attaching to belts up to 3" wide. Combinationleather/Ultra-Hyde™. Size: 7" x 10".

Electrician’s' Tool Pouch - No. 5164KLEIN

Electrician’s' Tool Pouch - No. 5168KLEIN

DescriptionNo. 5164. Has four large gusseted utility pockets, two plierpockets, two screwdriver pockets, knife snap. Combinationleather/Ultra-Hyde™. Size: 6-3/4" x 9-3/4".

Electrician’s' Tool Pouch - No. 5166KLEIN

DescriptionNo. 5168. Large pouch curved to fit the hip. Has a large andsmall utility pocket, two plier pockets, two screwdriver pockets,chain tape thong and knife snap. Combination leather Ultra-Hyde™. Size: 9" x 11".

K

Ordering Information

Order Mfg.No. No.KLN 007299 5164.

© 1996 TELEWIRE SUPPLY K26

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.KLN 007300 5166

Ordering Information

Order Mfg.No. No.KLN 007301 5168

Page 28: TWS Sec_K

DescriptionA high quality pouch specially designed for use by electrician's.Made of a combination of leather and Ultra-Hyde™.

Has extra large gusseted utility pocket, three plier pockets, twoscrewdriver pockets and knife snap.

Tools & Safety EquipmentTool Pouches & Bags

Utility PouchKLEIN

Tool PouchKLEIN

DescriptionHas ten separate compartments for a variety of pliers, screw-drivers and other tools. Has ring and tape thong. Favorite ofcable installers. Riveted throughout for long life. Combinationleather/Ultra-Hyde™.

Leather PouchKLEIN

DescriptionMade of a combination of leather and Ultra-Hyde™. Extra largegusseted utility pocket, two plier pockets, two screwdriver pock-ets and handy knife snap.

K

Ordering Information

Order Mfg.No. No. SizeKLN 007304 5190 6" x 8-3/4"

© 1996 TELEWIRE SUPPLYK27

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. SizeKLN 007294 5127 7' x 10"

Ordering Information

Order Mfg.No. No. SizeKLN 007293 5126 8-3/4" x 6"

Page 29: TWS Sec_K

Tools & Safety EquipmentTool Pouches & Bags

DescriptionThe Bashlin supporter strap (or gut strap) distributes the weightof the belt and tools. It is made of quality leather and has fouradjustable drop straps. Please furnish the even waist size. Addup to 4 or 6 inches to the trouser belt size.

This is not a safety belt.

10 Pocket Big Capacity Tool PouchKLEIN

Knife HolsterKLEIN

DescriptionRugged, big capacity pouch with 10 separate pockets. Fourlarge, gusseted utility pockets. Two pliers pockets. Four pock-ets for screwdrivers. Knife snap. Slotted pouch fits belts up to2" wide (51mm). Riveted and stitched. Made of Leather.

Supporter StrapBASHLIN

DescriptionLeather belt holster slotted to fit belts up to 2" wide. Holster holds both scissors and knife.

K

Ordering Information

Order Mfg.No. No. SizeKLN 039664 5165 10" x 10" (25 x 25 cm)

© 1996 TELEWIRE SUPPLY K28

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.BSH 604017 81-34"

BSH 81-36 81-36"

BSH 81-38 81-38"

BSH 81-42 81-42"

Ordering Information

Order Mfg.No. No. DescriptionKLN 050162 5187 Holster only

KLN 075054 46037 Complete kit

Page 30: TWS Sec_K

DescriptionThis is NOT an occupational protective belt. The durabil-ity of strap leather in a low-cost tool belt. Designed to carrylightweight tool pouches. Belt width: 1" (25mm).

K

Tools & Safety EquipmentTool Pouches & Bags

Heavy Duty Extra-Wide Leather BeltsKLEIN

Leather Utility BeltsKLEIN

DescriptionThis is NOT an occupational protective belt. This rugged 2"wide (51mm) belt is made of heavy strap leather and equippedwith a double-tongue buckle to stand up to years of service.

Ordering Information

Order Mfg.No. No. Size FitsKLN 122735 5415 Small 32" to 40"

KLN 007026 5415 Medium 36" to 44"

KLN 030895 5415 Large 40" to 48"

© 1996 TELEWIRE SUPPLYK29

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Size FitsKLN 006932 5201 Adjustable 33"-45"

DescriptionThis is NOT an occupational protective belt. Made ofleather with tool loops and chain-type thong. This belt may beused with all Klein pouches and holders. Belt width: 1-1/2".

Fully Adjustable Poly-Web Tool BeltsKLEIN

Leather Tool BeltsKLEIN

DescriptionThis is NOT an occupational protective belt. This strong,economical belt of polypropylene webbing has a slidingadjuster that allows a quick fit through the entire range of waistsizes. Provides easy adjustment for changes in sizes requiredby heavy winter clothing. Clasp buckle holds belt firmly but per-mits easy release. Belt width: 2-1/4".

Ordering Information

Order Mfg.No. No. Size FitsKLN 007022 5207M Medium 32" to 40"

KLN 007023 5207L Large 38" to 46"

Ordering Information

Order Mfg.No. No. SizeKLN 010059 5225 From 32" to 48"

Page 31: TWS Sec_K

K

Tools & Safety EquipmentTool Pouches & Bags

DescriptionMade of heavy No. 8 duck and nylon. The frame is steel whichis attached to the canvas with sturdy tubular rivets. Leatheretteextends up the sides 3". Bottom of bag is protected with steelstuds. Web handles are securely sewn to the bag.

5102 Series Canvas Tool BagsKLEIN

No. 10-S Tool BagBASHLIN

DescriptionMade of one-piece No. 8 white canvas covered on the bottomand 3" up the sides with Naugahyde, cemented and lock-stitched. Bottom is protected with steel studs. Mouth has steelframe. Handles are harness leather. All bags have 2 retainingstraps and buckles. Available with shoulder strap on specialorder at additional cost.

Ordering Information

Order Mfg.No. No. SizeKLN 006916 5102-18 18’’ long x 15"D x 6" W

KLN 006917 5102-20 20’’ long x 15"D x 6" W

KLN 006918 5102-22 22’’ long x 15"D x 6" W

KLN 006919 5102-24 24’’ long x 15"D x 6" W

© 1996 TELEWIRE SUPPLY K30

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Size WeightBSH 006921 10-S-22 22" x 12" x 7" 3-4 lbs.

Page 32: TWS Sec_K

DescriptionCast zinc swivel snap hook for use on hoisting buckets. Notfor use on safety lines. Maximum safe load: 150 lbs.

Tools & Safety EquipmentHand Lines & Hooks

Polypropylene Hand-Line with Snap HookKLEIN

No. 470 Swivel Snap HookKLEIN

No. 2012 Swivel Snap HookKLEIN

K

© 1996 TELEWIRE SUPPLYK31

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionThese are NOT occupational protective devices. Not forhuman support. Made of 5/16" four strand polypropylenerope, spliced to eye of snap hook. Red and white strand forhigh visibility. 75" long. Maximum safe load: 250 pounds.

Ordering Information

Order Mfg.No. No. DescriptionKLN 044116 1804-60 With 443A snap hook

Ordering Information

Order Mfg. Overall Eye ThroatNo. No. Length I.D. Opening

KLN 009096 2012 5" 3/4" 5/8"

DescriptionDrop-forged, with swivel clevis. Quick-acting, plunger stylelatch. Takes 1/2" or lighter hand lines. Swivel action preventsaccidental fouling into secondary wires. Safe load up to 750 lbs.

Ordering Information

Order Mfg. Overall Eye ThroatNo. No. Length I.D. Opening

KLN 009103 470 5" 1" 5/8"

Page 33: TWS Sec_K

K

Tools & Safety EquipmentTool Buckets

DescriptionOval bucket with 15 pockets inside. Made of No. 6 canvas, withtripod suspension, and equipped with No. 2012 swivel snap forhanging over cross arm hooks or attaching to hand lines.

DescriptionMade of heavy No. 1 canvas with a Cycolac top ring and mold-ed rubber compound bottom. Polypropylene rope handlespliced around top ring. With swivel snap.

Standard Canvas BucketKLEIN

Oval Bucket with 41 PocketsKLEIN

Heavy Duty Canvas BucketKLEIN

DescriptionMade of No. 6 canvas. Cycolac top rings and molded rubbercompound bottoms. Polypropylene rope handle is reinforcedwith leather where it is spliced around top ring.

Oval Canvas BucketKLEIN

Ordering Information

Order Mfg.No. No. SizeKLN 029723 5113 12" top diameter,

9" bottom diameter x 13" high

© 1996 TELEWIRE SUPPLY K32

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. SizeKLN 007533 5103S 12" top diameter

9" bottom diameter x 12" high

Ordering Information

Order Mfg.No. No. SizeKLN 007537 5144S 14" top diameter

8" bottom diameter x 10" high

DescriptionHas 26 pockets inside and 15 pockets outside for use by cablesplicers who use many color-coded tools. Made with heavy No.6 canvas. Bucket has Cycolac top ring and molded bottom.Tripod suspension rope is reinforced with leather where splicedaround top ring. Equipped with No. 2012 swivel snap hooks.

Ordering Information

Order Mfg.No. No. SizeKLN 140413 5152S 14"L x 8"W x 10" H

Page 34: TWS Sec_K

DescriptionDesigned to be attached to aerial baskets. Heavy duty No. 6canvas bucket has 15 pockets for tools. Furnished with twoABS hooks.

K

Tools & Safety EquipmentTool Buckets

Tapered Bottom BagKLEIN

Canvas Utility BagKLEIN

Tool BucketKLEIN

DescriptionDurable canvas bag designed with tapered bottom so parts willstay in the center of the bag. Two pockets are provided forsmall parts.

Constructed of No. 10 water repellent canvas. Furnished com-plete with snap for hanging.

Splicer’s Tool BagBASHLIN

DescriptionMade of No. 8 heavy brown canvas with 1/4" rope ring sewn intotop for extra rigidity. Snaps provided on loops for easy attach-ment to belts up to 3" wide. Ventilating eyelet in bottom. Topopening: 8" x 3".

Ordering Information

Order Mfg.No. No. SizeKLN 006909 5143 6-1/2" diameter; 8" depth

© 1996 TELEWIRE SUPPLYK33

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. SizeKLN 007536 5144 14" L x 8" W x 10" H

KLN 044174 5144H, replacement hook

Ordering Information

Order Mfg.No. No. SizeBSH 201810 717 15" x 7" x 9"

Ordering Information

Order Mfg.No. No. SizeKLN 007297 5142 9" x 10"

KLN 026864 5142P with inside pocket

DescriptionThis bag is made of #4 canvas, with a reinforced bottom. It has fourlarge pouches and ten small pockets. The top is PVC reinforced.

Page 35: TWS Sec_K

K

Tools & Safety EquipmentLadders

Features• Non-conductive — Type IA Industrial — 300 lb. • Meets OSHA standards• With strand hooks & pole grip

DescriptionTwo section extension ladders of non-conductive fiberglass.Side rails are 3-1/4" wide; rungs are 1-1/4" in diameter. Furnished with swivel type double-action safety shoes, ropeand pulley, V-rung and combination strand hooks.

Ladders are available in lengths from 16' to 32'.

Fiberglass LaddersLOUISVILLE

Features• Nexus coated • Type 1A• Strand hooks & pole grip attached• Extra heavy duty 300 lb. workload• Meets OSHA requirements• Non-Conductive

Ordering Information

Order Mfg. Rung Base OverallNo. No. Color Type Length Weight Length

LSV 040815 FE2624-E03 Orange round 12' 54 lbs. 24'

LSV 040816 FE2628-E03 Orange round 14‘ 62 lbs. 28'

LSV 040817 FE2632-E03 Orange round 16' 73 lbs. 32'

LSV 137714 FE3224-E03 Orange "D" 12' 54 lbs. 24'

LSV 137715 FE3228-E03 Orange "D" 14' 62 lbs. 28'

LSV 201809 FE3232-E03 Orange "D" 16' 73 lbs. 32'

7100 Series Electro-Master Fiberglass LaddersWERNER

© 1996 TELEWIRE SUPPLY K34

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionTwo section extension ladders for standard industrial andcontractor service. Has channel interlocking side rails com-bined with high tensile strength aluminum rungs. Lexan cast-ing protects all rail ends and cast aluminum spring-loadedgravity rung locks. Interlocking sections can be separated orreassembled easily. Furnished with swivel type double-action safety shoes, rope and pulley, V-rung and combinationstrand hooks.

Rail size: 3-1/4" x 1-1/8". O.D. base width: 16-7/8"I.D. base width: 14-5/8"

All Louisville Ladders are also available in yellow

Ordering Information

Order Mfg. Rung Base OverallNo. No. Color Type Length Weight Length

WER 093409 7124-2XA92 yellow round 12' 57 lbs. 24'

WER 093408 7128-2XA92 yellow round 14' 65 lbs. 28'

WER 093407 7132-2XA92 yellow round 16' 77 lbs. 32'

WER 604641 D7124-2XA92 yellow "D" 12' 57 lbs. 24'

WER 604156 D7128-2XA92 yellow "D" 14' 65 lbs. 28'

WER 604642 D7132-2XA92 yellow "D" 16' 77 lbs. 32'

Other sizes available

Page 36: TWS Sec_K

K

Tools & Safety EquipmentLadders

Fiberglass Special PurposeStep-to-Straight LaddersLOUISVILLE Description

All purpose non-conductive ladder converts quickly from astep ladder to a push-up extension ladder.

Flat, serrated, aluminum 3" steps on one side, aluminum roundrungs on the other. Flat steps on top section of ladder. Flaredback or base section.

Heavy duty, corrugated rubber pads on base of each leg. Pole grips standard.

DescriptionOrange 3-1/4" fiberglass side rails, interlocked, with surface veiltop layer. Heavy gauge steel bracket engages steel pin to locksections in step ladder position. Wall bumper protects surface atpoint of contact. Plate and rung assembly riveted at 4 points tothe fiberglass side rail. Traction-Tred™ deep serrations in rung.Nylon coated aluminum slide guides. Non-binding aluminumspreaders. Constructed with patented 3-piece Alflo® rung joint,producing a tempered joint, making the ladder Twist-Proof®. Overlap: 3'— parallel section: 14-1/2" O.D.; 12" I.D.; 17-1/2" O.D.of flared section at top. Depth of ladder in closed position: 7-1/8".

7800 Series Fiberglass Combination LaddersWERNER

Ordering Information

Order Mfg.No. No. Description Weight

LSV 038617 FC1006 6' Sections, extends to 9' 33 lbs.

LSV 135100 FC1007 7' Sections, extends to 11' 38 lbs.

LSV 034438 FC1008 8' Sections, extends to 13' 41 lbs.

© 1996 TELEWIRE SUPPLYK35

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Description

WER 042040 7806 Wt: 32 lbs. Height as stepladder, 6'working height as extension ladder, 9-1/2'

WER 057963 7807 Wt: 35 lbs. Height as stepladder, 7'working height as extension ladder, 11-1/2'

WER 042041 7808 Wt: 39 lbs. Height as stepladder, 8'working height as extension ladder, 13-1/2'

Features• Extra heavy duty—Type IA Industrial—300 lb. • Meets OSHA standards • Complies with ANSI code requirements

Features• Extra heavy duty, type 1A industrial - 300 lbs.• Meets OSHA requirements• Complies with ANSI code requirements

Page 37: TWS Sec_K

K

Tools & Safety EquipmentLadders

Fiberglass Step LaddersLOUISVILLE Features

• Type IA• Extra heavy duty, 300 lb. workload• Orange• Non-conductive reinforced• Rubber slip resistant foot pads• Tool tray top

DescriptionTop is non-conductive, has high impact resistance at high andlow temperatures, tough, durable and mar-resistant. Heavygusset bracing, inside spreader braces and skid-resistant feet.

Features• Non-conductive reinforced• Type IA industrial duty rating: 300 lbs.• Extruded heavy gauge aluminum tool tray top• Rubber slip resistant foot pads• Yellow

7200 Series Fiberglass Step LaddersWERNER

Ordering Information

Order Mfg.No. No. Length WeightLSV 135101 FS1003 3' step ladder 13 lbs.

LSV 060105 FS1004 4' step ladder 15 lbs.

LSV 600778 FS1005 5' step ladder 19 lbs.

LSV 135102 FS1006 6' step ladder 22 lbs.

© 1996 TELEWIRE SUPPLY K36

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Length WeightWER 080101 7203 3' step ladder 14 lbs.

WER 080102 7204 4' step ladder 17 lbs.

WER 042468 7205 5' step ladder 20 lbs.

WER 043864 7206 6' step ladder 20.5 lbs.

Page 38: TWS Sec_K

DescriptionCable hook and "V" rung assembly takes place of top rung.Steel "V" rung is faced with rubber pad for slip resistance.

Tools & Safety EquipmentLadder Accessories & Repair Kits

Rung Lock Kits

Rung Repair Kits

DescriptionComes in pairs with mounting hardware.

Cable Hook & "V" Rung Assembly

DescriptionReplacement rung, hardware and instructions.

K

Ordering Information

Order Mfg. Rung Fits Ladder No. Mfg. No. Type Series Weight

LSV 145320 Louisville PK100A round all 2 lbs.

LSV 145321 Louisville PK100C "D" all 2 lbs.

WER 603235 Werner 28-6 "D" 7100 2 lbs.

WER 066993 Werner 28-9 round 7100 2 lbs.

© 1996 TELEWIRE SUPPLYK37

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Fits Ladder No. Mfg. No. Series WeightLSV 094716 Louisville E03 all 4 lbs.

WER 603247 Werner 92-89 7100, D7100 4 lbs.

Ordering Information

Order Mfg. Rung Fits Ladder No. Mfg. No. Type Series Weight

LSV 146455 Louisville PK140A round all 1 lb

LSV 146454 Louisville PK141A "D" all 1 lb

WER 23-6F Werner 23-6F round-fly 7100 1 lb

WER 23-6B Werner 23-6B round-base 7100 1 lb

WER 23-7F Werner 23-7F "D"-fly D7100 1 lb

WER 23-7B Werner 23-7B "D"-base D7100 1 lb

Page 39: TWS Sec_K

Tools & Safety EquipmentLadder Accessories & Repair Kits

Shoe Repair Kit

Automatic Ladder LevelerJERSHON

DescriptionKit includes two shoe assemblies and hardware.

Rope & Pulley Repair Kit

DescriptionInstantly and automatically adjusts to any uneven surface, elim-inating unsafe blocking while saving time and money. Fits anywidth or length of aluminum or fiberglass extension ladder.Heavy duty construction - will not weaken the ladder. Easilyinstalled in the field.

K

© 1996 TELEWIRE SUPPLY K38

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Fits Ladder No. Mfg. No. Series Weight

LSV 146452 Louisville PK110A FE26XX 2 lbs.

LSV 146453 Louisville PK110D FE32XX 2 lbs.

LSV 146450 Louisville PK130A FS10XX 2 lbs.

WER 143797 Werner 26-5 all 2 lbs.

Ordering Information

Order Mfg. Fits Ladder No. Mfg. No. Series Weight

LSV 146451 Louisville PK120A all 8 oz.

Ordering Information

Order Mfg.No. No. DescriptionSTD 138106 EZE1000 "Level-Eze"

Page 40: TWS Sec_K

K

Tools & Safety EquipmentHand Tools

Cushion Grip ScrewdriversCRESCENT Description

Cushion grip handle sleeves are made of genuine PVC overtenite butyrate cores and have patented interlocking non-slipgrip. Oversized handles assure better grip and more turningpower. Heavy duty chrome vanadium alloy steel blades haveprecision cross ground flats and tips. All tips are sand blastedto prevent chipping of the plating.

TIP: Graphic on handle for easy identification in tool pouchof Phillips or slotted head.

© 1996 TELEWIRE SUPPLYK39

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. OverallNo. No. Tip X Shaft LengthCOO 136510 2343 -1&1/4 1/4" X 1-1/4" 3-1/8"

COO 136501 2343-4 1/4" X 4" 8-3/8"

COO 136548 2343-6 5/16" X 6" 11"

COO 136528 2343-8 3/8" X 8" 13-1/2"

Square Shank Keystone Tip

Order Mfg. OverallNo. No. Tip X Shaft LengthCOO 201777 2143-3 1/4" X 3" 6-3/4"

COO 136495 2143-4 1/4" X 4" 8-3/8"

COO 136513 2143-6 5/16" X 6" 11"

COO 201778 2143-8 3/8" X 8" 13-1/2"

COO 201779 2143-10 3/8" X 10" 15-1/2"

Round Shank Keystone Tip

Order Mfg. OverallNo. No. Tip X Shaft LengthCOO 201780 2142-4 1/4" X 4" 8-3/8"

COO 201781 2142-6 1/4" X 6" 10-3/8"

COO 136520 2243-3 3/16" X 3" 6-3/4"

COO 136492 2243-4 3/16" X 4" 7-3/4"

COO 136503 2243-6 3/16" X 6" 9-3/4"

COO 201782 2243-8 3/16" X 8" 11-3/4"

Round Shank Cabinet Tip

Order Mfg. OverallNo. No. Tip X Shaft LengthCOO 136489 2501 #1 X 3" 6-3/4"

COO 136517 2522 #2 X 1-1/4" 13-1/8"

COO 136487 2502 #2 X 4" 8-3/8"

COO 136515 2503 #3 X 6" 11"

Phillips Head Round Shank

Page 41: TWS Sec_K

K

Tools & Safety EquipmentHand Tools

Plastic Handle ScrewdriversCRESCENT

© 1996 TELEWIRE SUPPLY K40

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionMolded oversize butyrate plastic handles make for extra torquewith maximum comfort. Blades made of tough, long lastingchrome vandium alloy steel. Precision ground. All tips are sandblasted to prevent chipping of the plating.

Tip: Graphic on handle for easy identification in toolpouch of Phillips or slotted head.

Ordering Information

Order Mfg. OverallNo. No. Tip X Shaft LengthCOO 136582 343-4 1/4" X 4" 8-1/2"

COO 201783 343-6 5/16" X 6" 10-1/2"

COO 201784 343-8 3/8" X 8" 12-1/2"

COO 201785 343-12 3/8" X 12" 18"

Square Shank Keystone Tip

Order Mfg. OverallNo. No. Tip X Shaft LengthCOO 201786 143-3 1/4" X 3" 7-1/2"

COO 201787 143-4 1/4" X 4" 8-1/2"

COO 136587 143-6 5/16" X 6" 10-1/2"

COO 201788 143-8 3/8" X 8" 12-1/2"

COO 201789 143-10 3/8" X 10" 14-1/2"

COO 201790 143-12 3/8" X 12" 16-1/2"

Round Shank Keystone Tip

Order Mfg. OverallNo. No. Tip X Shaft LengthCOO 201791 243-3 3/16" X 3" 6-5/8"

COO 201792 243-4 3/16" X 4" 7-5/8"

COO 201793 243-6 3/16" X 6" 9-5/8"

COO 201794 243-8 3/16" X 8" 11-5/8"

COO 201795 243-10 3/16" X 10" 13-5/8"

Round Shank Cabinet Tip

Order Mfg. OverallNo. No. Tip X Shaft LengthCOO 201796 300 1/8" X 3" 5-5/8"

COO 136519 301 3/16" X 3" 6-5/8"

COO 136581 302 1/4" X 4" 8-1/8"

COO 136529 303 5/16" X 6" 10-1/2"

COO 201797 304 3/8" X 8" 12-1/2"

Phillips Head Round Shank

Page 42: TWS Sec_K

Screw Holding Screw driversKLEIN Description

Holds and starts slot-head screws, drives and sets them tight.Strong, "split" tip expands to grip many sizes of screws. Doesnot mar screw slot. Permits one-hand operation in hard-to-reach places. Tough plastic handle.

DescriptionCrank-action handle spins screws fast with one hand. Shankrotates in handle to save time and effort, especially on long-threaded screws in switch plates, light fixtures, etc.

K

Tools & Safety EquipmentHand Tools

Reversible 4 in 1 ScrewdriverXCELITE

Rapi-Driv Screw Driverswith Slotted or Phillips-TipsKLEIN

DescriptionExtra handy self-storing standard shaft. Screwdriver convertsin seconds to four most often needed tips: 3/16", 1/4" slottedand #1, #2 Phillips. Blades snap in easily and are held firmly bypatented spring lock assembly. Plastic handle.

Ordering Information

Order Mfg.No. No.COO 136585 FSD-1

© 1996 TELEWIRE SUPPLYK41

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Tip OverallNo. No. Tip Size Shaft LengthKLN 201768 670-3 Cabinet 3-16" 4" 7-3/4"

KLN 008641 670-6 Cabinet 3/16" 6" 9-3/4"

KLN 114546 681-6 Phillips #1 6" 9-3/4"

KLN 201769 682-6 Phillips #2 6" 9-3/4"

Ordering Information

Order Mfg.No. No. DescriptionKLN 008625 K34 Blade tip: 3/16", overall length, 8"

®

Page 43: TWS Sec_K

Tools & Safety EquipmentHand Tools

DescriptionScrulox square tip. Plastic handle. Shanks plated for protection.

Specialty Pocket ScrewdriverKLEIN

Cushion Grip AwlCRESCENT

DescriptionSmall but strong, this handy driver clips to shirt pocket. Flutedamber plastic handle with black trim. 1/8" blade tip width, 2"shank length. Overall length: 4-3/8".

Specialty Scrulux ScrewdriverXCELITE

DescriptionHeavy-duty, hard-pointed awl scribes metal, starts screw holes,performs a variety of piercing and punching jobs. Tempered steelshaft with reinforcing bolster at handle. Amber plastic handle incushion grip.

K

Ordering Information

Order Mfg.No. No.KLN 026847 A131-2

© 1996 TELEWIRE SUPPLY K42

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. ColorNo. No. Description CodeCOO 136556 SL-1 #1-point green

COO 136554 SL-2 #2-point red

Ordering Information

Order Mfg.No. No.COO 136496 2245

Page 44: TWS Sec_K

DescriptionConsists of 7 Nut Drivers with Butyrate handles and plastic pouch.

K

Tools & Safety EquipmentHand Tools

7-Piece Cushion Grip Nut Driver SetKLEIN

7-Piece Plastic Handle Nut Driver SetCRESCENT

DescriptionConsists of 7 nut drivers in plastic pouch.

Ordering Information

Order No: KLN 008586 Mfg. N0: 631

Contents: Mfg.No. Color Hex Size Shank Length

1. 630-3/16 black 3/16" 3-1/8"

2. 630-1/4 red 1/4" 3-1/8"

3. 630-5/16 yellow 5/16" 3-1/8"

4. 630-11/32 green 11/32" 3-1/8"

5. 630-3/8 blue 3/8" 3-1/4"

6. 630-7/16 brown 7/16" 3-1/2"

7. 630-1/2 red 1/2" 3-1/2"

© 1996 TELEWIRE SUPPLYK43

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order No: COO 201770 Mfg. N0: 700P

Contents: Mfg.No. Color Hex Size Shank Length

1. 700-3/16 black 3/16" 3-1/8"

2. 700-1/4 red 1/4" 3-1/8"

3. 700-5/16 yellow 5/16" 3-1/8"

4. 700-11/32 green 11/32" 3-1/8"

5. 700-3/8 blue 3/8" 3-1/4"

6. 700-7/16 brown 7/16" 3-1/2"

7. 700-1/2 red 1/2" 3-1/2"

DescriptionAmber plastic handle with cushion-grips and color coded endsfor size identification. Hex head drives nuts and socket screws.

Ordering Information

Order Mfg. Color Hex ShankNo. No. Code Size Length

COO 136500 CN6HS black 3/16" 3-1/8"

COO 201772 CN7HS brown 7/32" 3-1/8"

COO 136488 CN8HS red 1/4" 3-1/8"

COO 201773 CN9HS orange 9/32" 3-1/8"

COO 136493 CN10HS yellow 5/16" 3-1/8"

COO 136516 CN11HS green 11/32" 3-1/8"

COO 136497 CN12HS blue 3/8" 3-1/8"

COO 136491 CN14HS brown 7/16" 3-1/8"

COO 136490 CN16HS red 1/2" 3-1/8"

Individual Cushion Grip Nut DriversCRESCENT

Page 45: TWS Sec_K

K

Tools & Safety EquipmentHand Tools

DescriptionAutomatically adjusts to 15 different nut and screw sizes.Length: 7".

Driv-A-Matic Nut DriverKLEIN

© 1996 TELEWIRE SUPPLY K44

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.KLN 008587 632

Set Contains• Four 6-point sockets• 3/8", 7/16", 1/2" and 9/16"• Five 12-point sockets, 5/8", 11/16", 3/4", 13/16" and 7/8"• Eight 6-point deep sockets, 3/8", 7/16", 1/2", 9/16", 5/8",

1/16", 3/4" and 13/16"• Two extensions 1-1/2" and 3" long• Ratchet • Metal box

20 Piece 3/8" Socket Drive SetKLEIN

Ordering Information

Order Mfg.No. No.KLN 008432 65508

Set Contains• Four 6-point sockets, 3/8", 7/16", 1/2" and 9/16"• Four 12-point sockets, 5/8", 11/16", 3/4" and 13/16"• 5/8" spark plug socket• Two extensions 1-1/2" and 6" long• Ratchet• Metal box

12 Piece 3/8" Socket Drive SetKLEIN

Ordering Information

Order Mfg.No. No.KLN 037865 65504

Page 46: TWS Sec_K

DescriptionOpen ends have standard 15° angle; box ends are offset 15°.Both ends have the same size opening. Nickel chrome plated.6 point box end. Other sizes available.

DescriptionFor F fittings. 40 inch pounds.

K

Tools & Safety EquipmentHand Tools

Can WrenchKLEIN

Open-End WrenchKLEIN

Torque WrenchJACKSON

DescriptionAllows access to telephone boxes and pedestals. One endopens telephone-box fasteners and the other end tightens nutson binding-post terminals. Socket ends are color coded forquick identification of socket sizes. Sockets are thin-walled foreasy access into tight spaces and are 1-1/4" deep to fit overlong binding posts. Sockets are heat-treated alloy-steel and thehandle is made of a high-impact, break-resistant material.Sockets fit 3/8" and 7/16" hex nuts. Tool is 7" (178mm ) longwith a 1" (25mm) diameter.

Combination WrenchKLEIN

DescriptionBoth ends have standard 15° angle. Forged alloy steel,nickel chrome plated.

Ordering Information

Order Mfg.No. No.KLN 150372 68005

© 1996 TELEWIRE SUPPLYK45

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.JKS 140009 1514

Ordering Information

Order Mfg.No. No. Length SizeKLN 037946 68413 5-7/16" 7/16"

Ordering Information

Order Mfg.No. No. Length EndsKLN 038353 68461 5-1/16" 3/8" x 7/16"

Page 47: TWS Sec_K

Tools & Safety EquipmentHand Tools

DescriptionExtra capacity jaws open 3/16" wider than standard wrenches,permitting the use of a smaller wrench for a given application.Ideal for use with Coax Connectors. Nickel chrome plated withplastic dipped handles.

Adjustable WrenchesCRESCENT

No. 3146 Linemen’s WrenchKLEIN

DescriptionWorld famous Crescent adjustable wrench. Made of fine alloysteel to give extra strength and wear. Proportioned dimensionsfor greatest strength with minimum weight. Tension springunder knurl helps prevent jaw opening from changing adjust-ment. Open handle design permits easier knurl adjustment.Made of drop-forged alloy steel and heat treated for toughnessand durability.

507 Series Extra-CapacityAdjustable WrenchesKLEIN

DescriptionForged from special bar steel and heat treated. Each end hastwo different size openings. Hole is provided at larger end forturning-in standard pole steps. Particularly suited for use onheavy 3-bolt guy clamps on which the clearance for a wrenchis limited. For 5/8" hardware. Large end has 1-3/32" and 3-29/32" openings; small end has 13/16" and 5/8" openings.

K

Ordering Information

Order Mfg.No. No. Length CapacityChrome handles:

COO 136577 AC16 6" 3/4"

COO 136484 AC110 10" 1-1/8"

COO 136580 AC112 12" 1-5/16"

Tapered chrome handle:

COO 136499 AC115 15" 1-11/16"

Cushion grip handles:

COO 136579 AC14C 4" 1/2"

COO 136578 AC16C 6" 3/4"

COO 136505 AC18C 8" 15/16"

COO 136498 AC110C 10" 1-1/8"

COO 136509 AC112C 12" 1-5/16"

© 1996 TELEWIRE SUPPLY K46

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Length CapacityKLN 109154 D507-6 6" 1-5/16"

KLN 109155 D507-8 8" 1-1/8"

KLN 109152 D507-10 10" 1-5/16"

KLN 109153 D507-12 12" 1-1/2"

Ordering Information

Order Mfg.No. No. LengthKLN 008311 3146 13"

BSH 600182 (Holster) 111-BWH

Page 48: TWS Sec_K

DescriptionIdeal for working on hardline connectors. Smooth jaws won’tmar aluminum. Drop-forged, precision machined from the finestquality tool steel. Hardened, tempered, polished. Heavy dutynut and bolt joint. Self-locking jaw opening adjustment. Longhandles give powerful leverage. Textured plastisol grips providea sure grip under any condition.

Ribs are precision milled to ensure a smooth positive interlockbetween the two halves plus heavy duty nut and bolt results insafe, sure action with no chance of halves separating or jump-ing out of grooves.

Tools & Safety EquipmentHand Tools

Ratcheting Box WrenchesKLEIN

Pump PliersCRESCENT

DescriptionDesigned for use in confined areas or on long studs.Reverse ratchet by turning it over. Laminated constructionfor greater strength; chrome plated finish. In single and dou-ble hex; each end has a different size opening.

Smooth Jaw Pump PliersCRESCENT

DescriptionVersatile utility pliers, ideal for objects of all shapes, includingrods, pipes, hose and cable connections and many othermechanical devices. Drop-forged, precision machined from thefinest quality tool steel. Hardened, tempered, polished. Heavyduty nut and bolt joint. Self-locking jaw opening adjustment.Long handles give powerful leverage. Textured plastisol gripsprovide a sure grip under any condition.

Ribs are precision milled to ensure a smooth positive interlockbetween the two halves plus heavy duty nut and bolt results insafe, sure action with no chance of halves separating or jump-ing out of grooves.

K

Ordering Information

Order Mfg.No. No. Description SizeKLN 021745 68201 Single hex 5-1/2" L; ends, 3/8" x 7/16"

KLN 020786 68202 Double hex 6-1/2" L; ends, 1/2" x 9/16"

KLN 022502 68204 8" L; ends, 5/8" x 3/4"

© 1996 TELEWIRE SUPPLYK47

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. JawNo. No. Length Capacity WeightCOO 201440 F220CV 10" 2-1/8" 15.5 oz.

Ordering Information

Order Mfg. JawNo. No. Length CapacityCOO 136485 RT27CV 7" 1-1/8"

COO 136494 RT210C 10" 1-1/2"

COO 136504 RT212C 12" 2-3/8"

Page 49: TWS Sec_K

Tools & Safety EquipmentHand Tools

Features• Curved jaw with wire cutter-plated finish• Top quality design for superior performance• Designed for tight and confined areas• Unique jaw tooth design improves grip and turning ability• Compound action for powerful non-slip locking grip• Convenient, one-hand quick release lever• Accurate adjustments with screw machined ferrule

Slip Joint PliersCRESENT

Communications Cable CuttersH.K. PORTER

DescriptionChrome plated steel. Machines gripping teeth and wire cutter.Cushion grip handle.

Locking PliersCRESCENT

DescriptionDesigned for cutting communication cable. Shearing actionof the jaws which pass each other, minimize crushing ofinside wires.

Drop forged, alloy tool steel, heat treated cutter head.

Do NOT use to cut strand.

K

Ordering Information

Order Mfg. Overall JawNo. No. Length CapacityCOO 136586 G28C 6-12" 1"

© 1996 TELEWIRE SUPPLY K48

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. JawNo. No. Length CapacityCOO 201774 CP5C 5-1/2" 1-1/4"

COO 201775 CP7C 7-1/8" 1-5/8"

COO 201776 CP10C 8-5/8" 2"

Ordering Information

Order Mfg. Max.No. No. Length CutCOO 007839 0390CSP 37" 2-1/4"

Page 50: TWS Sec_K

DescriptionFor free or general cutting of soft or hard rods, bolts, colddrawn spring wire, stranded guy wire, alloy wire and rods notheat-treated, and hard steel up to Brinell 400, Rockwell C42hardness.

Cutting edge is in the middle of the blade with an equal bevelon each side.

Tools & Safety EquipmentHand Tools

Lightweight Power & CommunicationsCable CutterH.K. PORTER

Steel Strap CutterCOOPER TOOLS

DescriptionCutting capacity smaller on aluminum alloy and hard drawn cop-per. Capacity larger on soft aluminum or copper depending onhardness of conductor. Fiberglass handles.

Does not cut ACSR.

Do NOT use to cut strand.

Center Cut Bolt ClippersH.K. PORTER

DescriptionFor straps up to 1-1/4". Extra leverage with one hand makescontinuous cuts of wider steel strap quickly and cleanly.

Plastisol handle with black oxide, rust preventative finish. Cutsflat steel strap up to 1-1/4".

K

Ordering Information

Order Mfg. OverallNo. No. Length CableCOO 007836 0290FCS 25-1/2" 1-3/8"

© 1996 TELEWIRE SUPPLYK49

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Soft Hard Approx.No. No. Length Metal Metal Weight

COO 007819 1490MC 14" 5/16" 3/16" 2-3/4"

COO 007820 0090MC 18" 3/8" 1/4" 3-1/2"

COO 007823 0190MC 24" 7/16" 5/16" 5-1/4"

COO 007826 0290MC 30" 1/2" 3/8" 8-1/2"

COO 007829 0390MC 36" 9/16" 7/16" 12-7/8"

Ordering Information

Order Mfg. Overall Approx.No. No. Length WeightCOO 201766 1290G 12" 1-1/2 lbs.

OUR BEST

SELLER

Page 51: TWS Sec_K

Tools & Safety EquipmentHand Tools

DescriptionCuts up to 100 pair, 24 GA copper communications cable. Cutsstranded copper or aluminum cable up to 2/0, 262 strands, 23GA. wire. Patented off-set bite eliminates compression andfrayed ends. 8" long. Fits in tool pouch. Ideal for communica-tion, electrical and industrial applications. Extra strength #2blade finish for electrical cables and motor rewind.

No. UP-B76™ Coax CutterBENNER-NAWMAN

No. 63050 Cable CutterKLEIN

DescriptionCuts up to 3/4" O.D. copper and aluminum coaxial cable. Cutscleanly with one-handed action that eliminates cable distortion.Lightweight and compact tool is only 8-1/4" long and fits intotool pouch.

No. UP-B41™ Cable CutterBENNER-NAWMAN

DescriptionHigh-leverage design. Red plastic-dipped handles. Cable-gripping, shear-type jaws cut up to 4/0 aluminum (notACSR); 2/0 soft copper; up to 100-pair, 24-gauge communi-cation cable. Makes clean, efficient cuts. Not designed forcutting steel or ACSR.

Compact, only 9-1/2" long; can be carried in tool pouch or toolholders. Ideal for working in confined spaces.

K

Ordering Information

Order Mfg.No. No.BEN 023561 UP-B76

© 1996 TELEWIRE SUPPLY K50

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.BEN 007845 UP-B41

Ordering Information

Order Mfg.No. No.KLN 024567 63050

OUR MOST

POPULAR

CUTTER

Page 52: TWS Sec_K

DescriptionSmooth, streamlined nose with knurled jaws. High-leveragedesign provides greater cutting and gripping power than regu-lar 8-1/2" and 9-1/4" side cutters. Handform handles.

Tools & Safety EquipmentHand Tools

No. 0890CSJ Cable CutterH.K. PORTER

with thread holder

DescriptionHigh leverage, shear-type design cuts up to 4/0 aluminum and2/0 soft copper cable. Grips are plastic covered for non-sliphandling, and cutter fits neatly into most tool pouches.

NOT designed for cutting steel or ASCR. NOT an insulated tool.

213 Series High LeverageSide-Cutting PliersKLEIN

DescriptionSame design and cutting advantage as D213-9NE plier, butwith 5/8" diameter, 11 thread opening at the hinge for line work.

Lets you hold threaded end of bolts without damagingthreads, cleans and straightens threads, helps remove orinstall pole hardware more easily and safely.

K

Ordering Information

Order Mfg.No. No.COO 136557 0890CSJ

© 1996 TELEWIRE SUPPLYK51

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. SizeBlue plastic dipped handles:

KLN 008485 D213-8NE length, 8-1/2"

KLN 008489 D213-9NE length, 9-1/4"

High-dielectric orange plastic dipped handles:

KLN 008490 HD213-9NE length, 9-1/4"

Ordering Information

Order Mfg.No. No.Blue plastic dipped handles:

KLN 008491 D213-9NETH

High-dielectric orange plastic dipped handles:

KLN 008492 HD213-9NETH

A BEST

SELLER

Page 53: TWS Sec_K

201 SeriesNE Type Side Cutting PLiersKLEIN

K

Tools & Safety EquipmentHand Tools

DescriptionFor use on bare and insulated wire. Handform handles.Powerful leverage and keen cutting knives. Has plasticdipped handles.

2000 Series High LeverageNE Type Cutting PliersKLEIN

220 SeriesDiagonal Cutting PliersKLEIN

DescriptionSmooth, streamlined nose with knurled jaws. High-leveragedesign provides greater cutting and gripping power than regu-lar 8-1/2" and 9-1/4" side cutters. Combination polished andblack oxide finish. (Similar to 213-9NE series except with spe-cial "2000 Series" cutting knives. For bolts, nails & most hard-ened wire.) Blue Plastic dipped handles.

228 Series High LeverageHeavy Duty CuttersKLEIN

Ordering Information

Order Mfg.No. No.KLN 058445 D2000-9NE

© 1996 TELEWIRE SUPPLY K52

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. DescriptionKLN 008443 D201-6NE length, 6-1/4"

KLN 008446 D201-8NE length, 8-1/2"

KLN 008449 D201-9NE length, 9-1/4"

DescriptionShort tapered nose. Provides a greater mechanical cutting andgripping advantage than regular 8" heavy-duty diagonal cut-ters. Standard bevel cutting knives. Red plastic-dipped hand-form handles.

Ordering Information

Order Mfg.No. No.KLN 008501 D228-8

DescriptionHeavy duty pattern. Tapered nose and standard bevel cuttingknives. 1" jaws reach into confined spaces. Handform handles.Red plastic dipped handles. Overall length: 7-11/16".

Ordering Information

Order Mfg.No. No.KLN 008497 D220-7

Page 54: TWS Sec_K

DescriptionDiagonal cutting pliers with tapered nose and standard bevelcutting edges. Cushion grip handles.

DescriptionShort tapered nose with angled head. Standard bevel cuttingedges. Cushion grip handles.

K

Tools & Safety EquipmentHand Tools

248 Series High LeverageHeavy Duty Diagonal CuttersKLEIN

202 Series Diagonal Cutting PliersKLEIN

Heavy Duty Diagonal CuttersCRESCENT

DescriptionShort tapered nose with angled head. Angled head for easierwork in confined areas. Standard bevel-cutting knives. Redplastic-dipped handform handles.

Diagonal Cutting PliersCRESCENT

DescriptionTapered nose and standard bevel cutting knives. Red plastic-dipped handles. Without coil spring.

Ordering Information

Order Mfg. OverallNo. No. LengthKLN 008512 D248-8 8"

© 1996 TELEWIRE SUPPLYK53

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. OverallNo. No. LengthCOO 136506 542-7C 7"

COO 136576 542-8C 8"

Ordering Information

Order Mfg. OverallNo. No. LengthCOO 136522 942-5C 5"

COO 136574 942-6C 6"

Ordering Information

Order Mfg. OverallNo. No. LengthKLN 008450 D202-5 5-1/2"

KLN 008456 D202-6 6-1/16"

Page 55: TWS Sec_K

© 1996 TELEWIRE SUPPLY K54

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

K

Tools & Safety EquipmentHand Tools

DescriptionAn all-purpose cutting tool for telephone installation and main-tenance work. The W notches will slit acetate cellulose andother insulation from wires up to .058" OD. A stripping hole.052" diameter is provided in blades which also providesmeans to crimp on .032" and.025" single tube copper sleeves.Red plastic-dipped handles.

DescriptionThese pliers are for use on rubber-covered service wires suchas high strength drop wire, distributing frame wire and switch-board wire. A .027/.032 inch skinning hole is provided for remov-ing the conductor covering of 22GAD station wire and F crossconnect wire, and a .042/.047 inch skinning hole is provided forremoving rubber insulation of service wires. V-shaped notchesare provided on the edges of the pliers' jaw for use in skinningPVC insulated wire. There is a flat area with teeth between thehandles below the joint, for crushing insulation.

240 Series Diagonal CuttersKLEIN

Diagonal Cutting PliersCRESCENT

DescriptionWith .052" skinning hole. Tapered nose and standard bevel cut-ting knives. Red plastic-dipped handles.

Diagonal Cutting PliersKLEIN

Ordering Information

Order Mfg.No. No. LengthKLN 008506 D240-6 6-1/16"

Ordering Information

Order Mfg.No. No. LengthCOO 136486 932-6D 6-1/6"

Ordering Information

Order Mfg. OverallNo. No. LengthKLN 008454 D202-5-SW 5-1/2"

KLN 008515 D252-6-SW 6"

Page 56: TWS Sec_K

K

© 1996 TELEWIRE SUPPLYK55

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Description

Semi-flush cuttingSharp nose for working in confined areas. Specifically designedfor tip cutting. Widely used for trimming printed circuit boards.With coil spring. Pastel plastic-dipped handles.

Description4" diagonal cutting pliers - "Midget" size. Cushion grip handles.

Tools & Safety EquipmentHand Tools

252 Series Diagonal Cutting PliersKLEIN

No. 1004 Wire Stripper-CutterKLEIN

Midget Diagonal Cutting PliersXCELITE

209 Series Pointed NoseCutting Electronics PliersKLEIN

DescriptionA handy, light, compact tool for stripping insulation from wire.Convenient hole for looping or bending wire. With hold-openspring. Yellow plastic-dipped handles.

DescriptionHeavier design for all-purpose use. Tapered nose and standardbevel cutting knives. Red plastic-dipped handles.

Ordering Information

Order Mfg.No. No. LengthKLN 008513 D252-6 6"

Ordering Information

Order Mfg.No. No.COO 136572 54CG

Ordering Information

Order Mfg.No. No. LengthKLN 008474 D209-4C 4-3/16"

Ordering Information

Order Mfg.No. No. LengthKLN 008123 1004 5"

Page 57: TWS Sec_K

© 1996 TELEWIRE SUPPLY K56

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Tools & Safety EquipmentHand Tools

K

DescriptionLong nose design with cutters at hinge. Wrap, loop and cutwith one pliers. Cushion grip handles.

203 Series Heavy Duty LongNose Side Cutting PliersKLEIN

203 Series Long Nose SideCutting PliersKLEIN

DescriptionFor heavy gauge wires. Round nose, 2-3/4" long, forms loops.No. D203-8N has a skinning hole for No. 2 B&S insulatedwire.Yellow plastic-dipped hand form handles. Polished head.

Long Nose Side Cutting PliersCRESCENT

DescriptionStandard long nose design with cutting knives at hinge.Permits wrapping, looping and cutting with a single plier.

Ordering Information

Order Mfg.No. No. Description LengthKLN 008467 D203-8 8-5/16"

KLN 023599 D203-8N With skinning hole 8-5/16"for AWG insulated wire

Ordering Information

Order Mfg.No. No. Color Code SizeCOO 136575 654-6C 11/16" 6-5/8"

Ordering Information

Order Mfg. PointNo. No. Round LengthKLN 008459 D203-5 3/32" 5-9/16"

KLN 008460 D203-5C 1/16" 5-9/16"

KLN 008461 D203-6 1/16" 6-5/8"

KLN 008465 D203-7* 3/32" 7-1/8"

D-Indicates with plastic-dipped handles. C-Indicates with coil spring. *Has extra long nose, 2-7/16’’

Page 58: TWS Sec_K

K

© 1996 TELEWIRE SUPPLYK57

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Description6-5/8" long nose pliers. Outside nose surface coated with alu-minum oxide 3/4" from the tip. Plastic dipped handles

DescriptionBasic long nose pliers. Serrated jaws. Cushion grip handles.

Tools & Safety EquipmentHand Tools

203 SeriesStandard Side Cutters KLEIN

Slim Long Nose PliersKLEIN

Long Nose PliersCRESCENT

DescriptionFor telephone switchboard work. Two wire stripping holes for19 and 22-gauge wire. Yellow plastic-dipped handles.

Slim Long Nose PliersCRESCENT

DescriptionLonger nose and handles for deeper reach into work. Knurledjaws. Yellow plastic-dipped handles. Overall length: 5-9/16"with coil spring.

Ordering Information

Order Mfg.No. No. LengthKLN 008463 D203-6H2 6-5/8"

Ordering Information

Order Mfg.No. No. LengthWith coil spring:

COO 136569 1033-5-1/2SC 5-1/2"

Without coil spring:

COO 136523 1033-6C 6-5/8"

Ordering Information

Order Mfg.No. No.COO 136511 D long nose

Ordering Information

Order Mfg.No. No.KLN 008533 D307-5-1/2C

Page 59: TWS Sec_K

Tools & Safety EquipmentEquipment for Line Vehicles

Product NameBRAND

© 1996 TELEWIRE SUPPLY K58

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

K

Tools & Safety EquipmentHand Tools

DescriptionA special plier for telephone work designed to skin 22 or 24-gauge wire. Slot provided in nose to crush insulation. Yellowplastic-dipped handles.

DescriptionWith knurled jaws Designed for precision subminiature assem-bly work. Without coil spring. Pastel plastic-dipped handles.

Long Needle Nose PliersCRESCENT

301 Series Long Nose PliersKLEIN

Midget Slim Nose Electronics PliersKLEIN

Description

With knurled jaws Designed for precision subminiature assemblywork. Without coil spring. Pastel plastic-dipped handles.

Long Nose InsulationSkinning PliersKLEIN

DescriptionBasic long nose pliers with yellow plastic-dipped handles.

Ordering Information

Order Mfg. OverallNo. No. LengthCOO 136514 777-6SC 6-1/2"

Ordering Information

Order Mfg. OverallNo. No. LengthKLN 008547 D321-4-1/2 4-3/4"

Ordering Information

Order Mfg. OverallNo. No. LengthKLN 008566 D229 16"

Ordering Information

Order Mfg.No. No. Description LengthKLN 008519 D301-5 without coil spring 5-9/16"

KLN 008521 D301-6 without coil spring 6-5/8"

KLN 008522 D301-6C with coil spring to hold 6-5/8"jaws open & 1/16" point

Page 60: TWS Sec_K

K

© 1996 TELEWIRE SUPPLYK59

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Tools & Safety EquipmentHand Tools

No. 1006 Crimping Tool PliersKLEIN Description

For crimping non-insulated solderless terminals and connec-tors ranging from No. 10 to 22 AWG. Hardened wire cutter innose. Tapered nose for working in confined spaces. Plastic-dipped handles; one handle is red, the other black to identifycrimping position.

Description6-in-one tool shears bolts, cuts wire, strips wire, measuresstud sizes, gauges wire sizes and crimps insulated terminals.Red plastic covered handles.

No. 1000 All-Purpose ToolKLEIN

Ordering Information

Order Mfg.No. No. LengthKLN 034214 1006 9-3/4"

Ordering Information

Order Mfg.No. No. LengthKLN 008215 1000 7-1/2"

Page 61: TWS Sec_K

© 1996 TELEWIRE SUPPLY K60

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Tools & Safety EquipmentHand Tools

DescriptionA heavy-duty, double-duty hammer with special high-carbonsteel head. Driving end is octagon shaped, claw is thick forextra strength. Painted blue finish; hickory handle.

Hand Drilling HammerPLUMB

Lineman’s Double-Face HammerKLEIN

DescriptionExtra heavy, drop forged steel head. Wedged handle for easyreplacement. Hickory handle is short for use in close quarters.

Lineman’s Straight Claw HammerKLEIN

DescriptionDesigned for pole-line work, with drop forged tempered steelhead only 3-3/4" long, for use in confined areas. Faces areidentical, with 1-3/4" round-crown driving surfaces with bevelededges. Perforated neoprene grip bonded to fiberglass handle.

K

Ordering Information

Order Mfg. OverallNo. No. Length WeightCOO 136567 11-649 10-3/4" 48 oz.

Ordering Information

Order Mfg. OverallNo. No. Length WeightKLN 021271 832-32 13-1/2" 32 oz.

Ordering Information

Order Mfg. OverallNo. No. Length WeightKLN 007910 809-36 14" 36oz.

Page 62: TWS Sec_K

K

© 1996 TELEWIRE SUPPLYK61

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionDrop forged tempered steel heads, round and polished, withcurved or straight claw. Perforated neoprene grip bonded tofiberglass handle.

Tools & Safety EquipmentHand Tools

Electrician’s HammerKLEIN

Sledge HammerKLEIN

Heavy Duty HammersKLEIN

DescriptionPolished, drop forged, tempered steel head designed withstraight claw and narrow face for reaching into outlet boxes.Perforated neoprene grip bonded to fiberglass handle.

DescriptionDouble-faced hammer with high qualityforged, heat-treated steel head.Striking faces are polished andbeveled. Flat red paint finish on sides ofheads. Select, flame-treated, wedgedhickory handle.

Ordering Information

Order Mfg. Overall HeadNo. No. Length WeightKLN 007922 807-18 14" 18 oz.

Ordering Information

Order Mfg. OverallNo. No. Description Length WeightKLN 007912 808-16 Straight claw 13" 16 oz.

KLN 007915 808-20 Straight claw 13" 20 oz.

KLN 020489 818-16 Curved claw 13" 16 oz.

Straight Claw

Curved Claw

Ordering Information

Order Mfg. Handle Head Face Overall Head TotalNo. No. Length Length Diameter Length Weight WeightKLN 103459 22204 10-1/2" 5" 2" 12-1/2" 4 lbs. 4-1/2 lbs.

Page 63: TWS Sec_K

K

© 1996 TELEWIRE SUPPLY K62

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Tools & Safety EquipmentMeasuring Devices

DescriptionStrong, hardwood rules 6’ long. Graduated on both edges in16ths and inches. Stud markings indicated. Special abrasion-resistant finish. Joints and protector strike plates brass plated.

Power-Return Steel Tapes

Enclosed Case Fiberglass TapeKLEIN

DescriptionPositive lock, thumb-action control knob. Black numerals onyellow background. Resists abrasion, rust, oils and acids.Graduated on both edges in 16ths, inches and feet. Chrome-plated case, replaceable blade, belt clip.

Folding Wood Rules

DescriptionMoisture proof coating of polyvinyl-chloride ensures durability,adds to the dielectric strength and protects against oil or chem-icals. Can be immersed in water and will not be affected. Blackfigures on a white background. All metal parts nickel plated.Tape line is graduated in feet, inches to 8ths. Graduations andnumbers are black. Foot markings are red. Line reads instan-taneous feet and inches.

Ordering Information

Order Mfg.No. No. Length WidthCOO 136559 2210 10' 1/2"

COO 136560 2312 12' 3/4"

KLN 008006 922-16 16' 3/4"

KLN 008007 922-20 20' 3/4"

COO 136561 2125 25' 1"

Ordering Information

Order Mfg.No. No. Description

COO 136583 066F Inside reading - lays flat on work surface

KLN 007990 906-1 Outside reading - see picture

Ordering Information

Order Mfg.No. No. SizeKLN 032304 946-100 100' L x 1/2" W

Page 64: TWS Sec_K

K

© 1996 TELEWIRE SUPPLYK63

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionDesigned for contractors, engineers, estimators, utility men,road builders, land appraisers and many others. 4 foot circum-ference steel disc wheel permits easy movement through brushand undergrowth.

Measures accurately over most kinds of terrain and in all weath-er. Wheel is calibrated to 1/2" on one side and 1/2 of one-tenthof a foot on the other. Available in equipment orange or safety-glo enamel finish.

Tools & Safety EquipmentMeasuring Devices

No. 400 Measuring WheelROLATAPE

Replacement PartsROLATAPE

DescriptionDesigned for most outdoor measuring needs. Used by con-struction companies, utilities, and municipalities. Records dis-tances up to 100,000 feet. Total is registered in feet on counterwhich is in plain view of operator at all times. Counter can bereset at any distance. Measurements can be checked to within2" or less by inspection. Equipped with automatic brake and abuilt-in stand. Wide neoprene tire, 4 feet in circumference,assures firm traction over most surfaces with precision accura-cy. When handle is retracted, entire unit can be carried easily.Equipment orange enamel finish.

No. 415 Measuring WheelROLATAPE

DescriptionInterchangeable parts for Models 400, 415, 600, 623, 623-Golf, 400/415 Dual, 400/415 Extended and 623 Dual.

Ordering Information

Order Mfg. Wheel ShippingNo. No. Diameter Weight Weight

RTP 008012 400 15-1/2" 5-1/4 lbs. 9 lbs.

Carrying CaseROLATAPE

DescriptionCase for No. 400 and 415 measuring wheels.

Ordering Information

Order Mfg.No. No. DescriptionRTP 008018 60-400 Counter-reset

RTP 008019 60-L Lever arm assembly

Ordering Information

Order Mfg.No. No.RTP 008017 400-415

Ordering Information

Order Mfg. Wheel ShippingNo. No. Diameter Weight Weight

RTP 008013 415 15-1/2" 7.8 lbs. 11 lbs.

Page 65: TWS Sec_K

© 1996 TELEWIRE SUPPLY K64

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

K

Tools & Safety EquipmentMeasuring Devices

Measuring SticksHASTINGS Description

Lightweight, safe and compact. Ideal for taking fast and accu-rate vertical measurements of overhead lines, highway clear-ances, structural heights and checking sag. Eye level readingeliminates need for calculations. Extended height is shown attop of base section. Spring loaded pin lock at base of each sec-tion. Bronze hook on tip end. Will not chip or peel. Marked withfoot, inch and one-half inch measurements.

Ordering Information

Order Mfg.No. No. DescriptionHTG 006772 E1-125 25' height

HTG 006774 E1-130 30' height

HTG 006776 E1-135 35' height

HTG 006778 E1-140 40' height

Water repellent, vinyl snap top carrying case 20'-25' heavy duty, 20'-25'-30' standard lengths

HTG 006843 C-30

Water repellent, vinyl snap top carrying case 30' heavy duty, 35' standard length

HTG 006844 C-35

The illustrations above are examples only, consult theNational Electric Safety Code for complete clearance rules.

Page 66: TWS Sec_K

K

© 1996 TELEWIRE SUPPLYK65

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Tools & Safety EquipmentScissors & Knives

DescriptionComplete, compact splicing kit contains cable-splicer’s knifeN0.44200, electrician’s scissors with stripping notches N0.2100-7 and slotted leather holder N0.5187. For belts up to 2"wide (51mm).

Ordering Information

Order Mfg.No. No. Description

KLN 075054 46037 complete cable splicer’s kit(2-1/8" x 7-1/2") (5 19cm)

KLN 050162 5187 holder only - slotted to fit belts up to 2" wide (51mm) 2-1/8" x 7-1/2" (5 19cm)

KLN 058451 5187T holder only - with tunnel loop for belts up to2" wide (51mm)not available in Cable Splicer’s kit No 46037

DescriptionHot drop-forged. Length: 5". Length of cut: 1-7/8".

Ordering Information

Order Mfg.No. No. Description

COO 008064 175-E fully nickel plated, scraper and file on backedge of blade, polished sharp points

COO 008065 175-E3 1 blade serrated, 1" back from point

COO 008067 175-E5 5nickel plated, notch for 19 and 23 gaugewire, scraper and file on back edge of blade

Cable-Splicer’s KnifeKLEIN Description

Special-purpose short blade with comfortable, full sized,heavy-duty handle. Coping-type blade made of the finest cut-lery steel, tough and carefully tempered to hold its edge. Non-slip handle is plastic dipped for comfort.

Ordering Information

Order Mfg. Blade OverallNo. No. Length Length

KLN 050160 44200 1-3/4" 6-1/4"

N0. 175-E Solid SteelElectrician’s ScissorsWISS

Cable Splicer’s KitKLEIN

Page 67: TWS Sec_K

© 1996 TELEWIRE SUPPLY K66

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

K

Tools & Safety EquipmentKnives

Lineman’s KnifeKLEIN Description

Extra-large curved sheep foot slitting blade 2-5/8" long; auto-matically locks in open position. Ideal for heavy-duty linework. Carbon steel blade.

DescriptionStandard spear point blade 2-1/2" long and screwdriver-tipblade 2-1/2" long. Screwdriver blade locks open. Strong rivetedconstruction. Tough plastic handles won’t crack or chip; handlesare textured for better gripping. Tempered cutlery steel blades.

DescriptionTop button moves, heavy-duty razor-edged blade to any ofthree cutting positions. Double-ended, reversible bladeretracts fully for carrying. Lightweight aluminum handle isshaped for comfort. Comes with three blades; extra bladesstore in handle.

Pocket KnifeKLEIN

Retractable-Blade UtilityKLEIN

Electrician’s KnifeKLEIN

DescriptionExtra-large, stainless steel, curved sheep foot slitting blade 2-1/2" long. For heavy-duty line work. Blade locks open. Hand-form type handle.

Ordering Information

Order Mfg. ClosedNo. No. Description LengthKLN 007960 44100 utility knife 6"

KLN 023154 44101 5-pack of blades

Ordering Information

Order Mfg. ClosedNo. No. LengthKLN 007955 1550-2 3-3/4"

Ordering Information

Order Mfg. ClosedNo. No. LengthKLN 031140 1550-24 4-3/8"

Ordering Information

Order Mfg. ClosedNo. No. LengthKLN 007947 1550-4 4"

Page 68: TWS Sec_K

K

© 1996 TELEWIRE SUPPLYK67

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionCompact, lightweight knives with 2-1/4" long coping type blade.Ideal for skinning small wire and cable. Tough plastic handle;ring for attaching to snap. Wrought shackler riveted to handle.Carbon steel blade.

Tools & Safety EquipmentKnives

Lineman’s and Electrician’s KnivesKLEIN

Three Blades Electrician’s KnifeKLEIN

DescriptionNo. 1550-7: Curved sheep foot slitting blade 2-3/8" long andscrewdriver-tip blade 2-1/2" long. Screwdriver blade locksopen. High grade steel carefully tempered. Handles are of spe-cial plastic that won’t chip or crack. Fitted with wrought shack-les riveted to handle.

No. 1550-10: Insulation-slitting blade 1-1/2" long and sheepfoot skinning blade 2-3/8"long. Slitting blade locks open.

Skinning KnifeKLEIN

DescriptionCurved sheep foot skinning blade 2-3/8" long, standard spearpoint blade 2-1/2" long and screwdriver-tip blade 2-1/2" long.Screwdriver blade locks open. Made of high grade cutlery steelcarefully tempered. Tough plastic handle.

Ordering Information

Order Mfg. Closed No. No. LengthKLN 007950 1550-7 3-3/4"

KLN 007959 1550-10 3-3/4"

Ordering Information

Order Mfg. Closed No. No. LengthKLN 007949 1550-5 3-1/4"

Ordering Information

Order Mfg. Closed No. No. LengthKLN 007957 1550-6 3-3/4"

Page 69: TWS Sec_K

© 1996 TELEWIRE SUPPLY K68

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

K

Tools & Safety EquipmentHack Saws

DescriptionBlade cuts fully through to a flat surface; converts easily fromvertical to horizontal position for full-flush cutting. Tubular steelframe, die cast zinc handles with blue finish. Man-sized gripand curved front-end design for comfortable two-hand use.Storage chamber for extra blades. Supplied with blade.

DescriptionLasts twice as long as high speed steel and up to ten timeslonger than carbon steel. With exceptional combination of toothhardness and shock resistance, these blades can operate 20-50% faster, resulting in lower costs per cut.

No. 12P High Tension HacksawNICHOLSON

Bi-Metaloy Hacksaw BladesNICHOLSON

DescriptionRugged, lightweight frame built for professional tool users. UseNicholson Bi-Metaloy® blades and achieve a remarkableimprovement in cut-off performance - no blade twist, reducedbinding, square cuts, better finish. Cuts faster through thetoughest materials and blades last longer. Screw-operatedlevel with folding handle for tensioning the blade up to 30,000psi. The higher the tension reading, the greater the blade beamstrength and cutting results.

No. 701 Heavy Duty HacksawsKLEIN

Ordering Information

Order Mfg.No. No.COO 136563 80965

Ordering Information

Order Mfg.No. No. DescriptionCOO 136525 62644 12" long, 18 TPI

COO 136564 62645 12" long, 24 TPI

Ordering Information

Order Mfg.No. No. Size

KLN 008031 701-10 Blade length 10" - overall length 14"

Page 70: TWS Sec_K

K

© 1996 TELEWIRE SUPPLYK69

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Special "Shatterproof" Hacksaw BladesNICHOLSON

DescriptionHacksaw frame is corrosion-proof, polished nickel with 3-3/8"/86mm throat, adjustable for 10"/254mm or 12"/305mmblades. Molded plastic handle. Blade holding bolts areadjustable to four positions. Rear bolt has wing nut for easytensioning of blade. Each frame is individually packed andequipped with a 10"/254mm Nicholson blade.

Tools & Safety EquipmentHack Saws

No. 10 HacksawNICHOLSON

DescriptionSpecially hardened to induce toughness. Because of thisextreme toughness, one tooth coarseness greater than thatnormally recommended can be used. Cutting speed on thinstocks can be increased. This blade is not recommended forhigher carbon or alloyed steels.

"Quick-Start" Hacksaw BladesKLEIN

DescriptionWith special starter teeth at front end to lead conventional teethinto the work. Suitable for use on pipe, conduit, tubing, BXcable, sheet metal, low carbon steel and non-ferrous metals.

Ordering Information

Order Mfg.No. No. DescriptionKLN 044100 1018C 10" long, 18 TPI

KLN 008034 1024C 10" long, 24 TPI

KLN 008035 1218C 12" long, 18 TPI

KLN 008040 1232C 12" long, 32 TPI

Ordering Information

Order Mfg.No. No.COO 136524 80952

Ordering Information

Order Mfg.No. No. DescriptionCOO 136526 63112 10" long, 24 TPI

COO 136570 63145 12" long, 18 TPI

COO 136565 63158 12" long, 24 TPI

COO 136562 63171 12" long, 32 TPI

Compact Utility HacksawNICHOLSON Description

Great for cutting sheetrock when wall fishing wire.Uses any hacksaw blade. Comes complete with blade.

Ordering Information

Order Mfg.No. No.COO 201765 80968

Page 71: TWS Sec_K

© 1996 TELEWIRE SUPPLY K70

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Tools & Safety EquipmentHeat Shrink Torches

DescriptionLarge, full heat shrink flame. Torch has an aluminum housingwith an epoxy finish, plus a stainless steel burn tube and brasstip. Instant on, instant off feature extinguishes the flame whenuser’s finger is removed from the control knob. Built in pressureregulator never needs adjustment. Torch burns efficiently in anyposition and will operate with propane, Mapp gas or propylene.Can be used with 14 oz. cylinder or extension hose with remotefuel source. With trigger guard.

Quick-Fire™ Self-Igniting TorchTURNER

Panther Self Starting TorchBERNZ-O-MATIC

DescriptionThe new Turner Quick Fire self-igniting torch is easy to use. Nomatches, no spark lighters, just a simple press of the piezo igni-tor button gives instant flame. The high performance pressureregulator allows higher temperatures than conventional torch-es and because of the simple and efficient easy on/easy off,fuel use is very economical.

Surefire Heat Shrink TorchBERNZ-O-MATIC

DescriptionThe Panther instant-firing propane torch gun features a triggeractuated, ceramic ignitor for thousands of lights. A high intensi-ty flame holder and precise air metering produce a hot swirlflame which is suitable for sweating, soldering or brazing.Comes with one fuel cylinder.

K

Ordering Information

Order Mfg.No. No.COO 136550 HT-280 propane

Ordering Information

Order Mfg.No. No.BRZ 077435 T-751

Ordering Information

Order Mfg.No. No.BRZ 053277 TS 500MK

OURHOTTEST

SELLER

Page 72: TWS Sec_K

K

© 1996 TELEWIRE SUPPLYK71

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Features• For use with propane/high temperature brazing fuel• Produces a soft yellow flame, ideal for most heat

shrink applications• Adjustable pressure regulator for a consistent flame

under all conditions• For use with standard disposable fuel cylinders

(cylinder not included)• 1" (25mm) diameter heavy-duty heat shrink tip• Cylinder valve• 5' hose and operating instructions• Generates 6,000 - 13,000 BTUH when using propane fuel

Tools & Safety EquipmentHeat Shrink Torches

Adapter HoseTURNER

Regulated Heat Shrink TorchTURNER

Features• Connects all standard torches to standard disposable fuel cylinder• Convenient for bucket truck or where longer hose is needed• 10' hose• Complete with cylinder stand• Weighs 2 lbs.

Standard Heat Shrink TorchTURNER Features

• For use with propane/high temperature brazing fuel• Produces a soft yellow flame, ideal for most heat

shrink applications• For use with standard disposable fuel cylinders

(cylinder not included)• 1" (25mm) diameter heavy-duty heat shrink tip• Cylinder valve• Up front flame control valve• 5' hose and operating instructions• Generates 22,000 BTUH at maximum setting when

using propane fuel

Ordering Information

Order Mfg.No. No.COO 009308 90-017

Ordering Information

Order Mfg.No. No.COO 115333 90-018

Ordering Information

Order Mfg.No. No.COO 201767 LP5550-120

OUR

HOTTEST

SELLER

Page 73: TWS Sec_K

© 1996 TELEWIRE SUPPLY K72

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Tools & Safety EquipmentHeat Shrink Torches

DescriptionDesigned to operate with one-pound cylinder of either Mappor propane gas. Offers choice of gas to suit heat require-ments for silver soldering copper tubing, bronze brazing steelpipe, or soldering with water in the line. Performs well in tem-peratures below freezing, but not below 10°F.

Portable torches feature swirl burners, 360° swivel tips foreasy use in any position, rugged metal capped regulator,easy-to-clean orifice. Large and small interchangeable tipsare available as well as heat shields for each size tip.Torches light instantly, will not blow out and will operateupside down.

STK-9 hand torch kit includes STK-R pressure regulator andST-3 large tip.

No. KCA110 Heat Shrink KitUNIWELD

Heat Shrink TorchTURNER

Description• Mapp® or Propane

Field tested and proven soft wrap-around flame for communi-cations cable shrink tube applications.

Gold Metal Dual-Fuel Hand TorchesTURBO TORCH / WINGERSHEK

DescriptionBurns up to 30 minutes between refills. Can be used withpropane or other high temperature fuels. Has interchangeableLP-969-2 heat shrink torch tip, a handle that is comfortable andfire resistant, plus a stand for stationary use. Complete instruc-tions are included to make refilling safe.

K

Ordering Information

Order Mfg.No. No. DescriptionUWD 039644 KCA110 Heat shrink kit

Ordering Information

Order Mfg.No. No.VCT 052424 STK-9

Ordering Information

Order Mfg.No. No.COO 022752 90-051

Page 74: TWS Sec_K

K

© 1996 TELEWIRE SUPPLYK73

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Tools & Safety EquipmentHeat Shrink Torches

Disposable Steel Fuel CylindersTURNER

Flint LighterWELLER

DescriptionPropane fuel cylinders. 14.1 oz. cylinder for use on any torchor propane appliance. 12 per carton; shipping weight: 25 lbs.

Ordering Information

Order Mfg.No. No.COO 009317 LP175-9

Ordering Information

Order Mfg.No. No. DescriptionCOO 115325 LP624-2 flint lighter

COO 038358 LP625-2 replacement flints for lighter

Fiberglass Fish Tape and Tapemaster ReelHOLUB

DescriptionThe Castmaster combines the 1/8" diameter ultralite fishing rodand the patented Tapemaster dispenser reel. Uniform pressureapplied 360° around the reel opening means smooth dispens-ing and rewinding with no jams or "pop-out" problems. TheCastmaster includes 1/8" ultralite rod assembled in the patent-ed Tapemaster reel & winder, and an assembled small pullingeye (14-858).Ordering Information

Order Mfg.No. No. DescriptionHLB 108495 14-806 50’ rod in 8-1/2’’ diameter reel

HLB 108498 14-807 100’ rod in 12’’ diameter reel

Page 75: TWS Sec_K

© 1996 TELEWIRE SUPPLY K74

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

K

Tools & Safety EquipmentFish Tapes

DescriptionHigh grade flat spring steel. Tough, durable plastic reel andwinder are dent-proof, rust-proof and wear-proof. Built-inwinder speeds paying-out and re-winding tape. Big grips forpulling. Reels are bright yellow. Tape size 1/8" x .06"

Tapemaster II MetalFish Tape, Reel & WinderHOLUB

Ordering Information

Order Mfg.No. No. Length Reel SizeHLB 024269 14-250 50' 8-1/2"

HLB 007878 14-258 100' 12"

HLB 007880 14-259 200' 12"

DescriptionRugged, easy-to-use Klein winder reel keeps flat spring-steeltape in its place. Comfortable, easy-grip lets you turn reel ineither direction. Compact, high-impact Cylolac® reel is light,but built to take hard use. Internal nylon safety band stops tapefrom "popping out". Reel disassembles easily to replace orswitch tapes, reassembles in minutes.

Fish Tape, Reel & WinderKLEIN

Ordering Information

Order Mfg.No. No. DescriptionKLN 077879 50205 50' x 1/8 x .060" reel dia. 8-1/2"

KLN 100244 50210 100' x 1/8 x .060" reel dia. 12"

KLN 063205 50220 200' x 1/8 x .060" reel dia. 12"

Leader for Flat Steel Fish TapeKLEIN

DescriptionFlexible 13-1/2" (34cm) leader makes pushing and pulling flatsteel tapes easier. Heavy duty 3/16" diameter wound steelspring with rust proof inner steel cable will lead flat tapesthrough 90° bends and can withstand 500 lb. pull.

Eye-loop accepts up to five unstripped No.12 wires.

Ordering Information

Order Mfg.No. No. Description

KLN 078103 50350 Leader for 1/8" or 1/4"* flat steel fish tapes

* 1/4" tape ends must be ground to 1/8" width.

Page 76: TWS Sec_K

K

© 1996 TELEWIRE SUPPLYK75

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Tools & Safety EquipmentFish Tapes

Little Buddy Conduit RodderJAMESON Description

For fishing conduit as small as 3/4". Designed for telecommuni-cations, power utilities, computer network, electrical wire andcable pulling.

Features• Safe rigid 1/8" diameter solid fiberglass core rod with

copolymer protective outer sheath, bright orange in color for high visibility (total O.D. size is 3/16")

• Available in 150, 200 and 300 foot lengths• New! optional markings every 5 feet or every meter for

convenience in measuring conduit runs• High impact polymer canister reduces weight and offers

longer lengths in compact sizes• Unit operates in vertical or horizontal positions for

flexible application

Good Buddy Conduit RodderJAMESON

Ordering Information

Order Mfg.No. No.JMS 201935 10-316-150

Ordering Information

Order Mfg.No. No.JMS 10-316-300 10-316-300

DescriptionFor fishing conduit from 2" to 4". Designed use in manholes,cable vaults and for larger conduit in buildings.

Features• Safe, non-conductive high-flex 1/4" diameter fiberglass

core rod with copolymer protective outer sheath, bright orange in color for high visibility (total O.D. size is 3/8")

• Available in 300, 400 foot, and special lengths, upon request• New! optional markings every 5 feet or every meter for

convenience in measuring conduit runs• Portable frame collapses to 10" width and can be taken into manhole• Reel is adjustable to allow payout in vertical or horizontal

positions where space is a problem

Page 77: TWS Sec_K

© 1996 TELEWIRE SUPPLY K76

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

K

Tools & Safety EquipmentFish Tapes

Big Buddy® Conduit RodderJAMESON

Ordering Information

Order Mfg.No. No.JMS 201934 11-38-500C

JMS 104139 11-38-1000C

DescriptionFor fishing or rodding conduit 4" or larger. Designed for use inunder ground duct from manhole to manhole and manhole tosubsidiary ducts; ideal for long-run fiber optic cable installation.

Features• Continuous 3/8" diameter solid fiberglass core rod with

copolymer protective outer sheath, bright orange in colorfor high visibility (total O.D. size is 1/2")

• Available in 500 to 1,000 foot lengths• New! optional markings every 5 feet or every meter for con-

venience in measuring conduit runs• 44" reel rides on 10" high-impact resistant wheels for ease

in portability• Operates and stores in horizontal or vertical position. Fits

most mini-vans

DescriptionThe Power Dart® Blower is a pneumatic rodding system espe-cially suited for long duct runs. A three-motor system allowsyou to choose the right speed for your needs. With all threemotors engaged, the Power Dart Blower will deliver up to 300cfm (8.5 m3/min) of air or 3 psi (.2 bar) max. pressure, easilyblowing 1/2" (13 mm) poly line or measuring tape over 2,000feet (610 m) in conduit up to 6 inches (152 mm) in diameter.The complete kit comes with 25 feet (7.6m) of air hose, anassortment of conduit seal-offs, and an assortment of mis-siles. Weighs only 31 pounds (14 kg) and operates at 110 or220 Volts. 110 Volt model includes a 30 amp twist plug. The220 Volt model includes a NEMA 6-15P plug (other plug typesare available). Requires a 3.000 Watt generator.

Utility Power Dart Kitincludes the following items for utility applications:

• Blower Unit• 25' (8m) x 2-1/2" (64 mm) heavy duty hose• Seal-off Body• Seal-offs for 1/2" (13 mm) - 6 (152 mm) conduit• Line Missiles for 2" (51 mm), 3" (76 mm), 4" (102 mm),

5" (127 mm) & 6" (154 mm) conduit

Power Dart BlowerCONDUX

Ordering Information

Order Mfg.No. No. Description

CDX 202096 08030000 110 Volt system with 30 amp twist plug

Page 78: TWS Sec_K

Tools & Safety EquipmentHand Tools

Throwing WeightJACKSON

Aluminum Torpedo LevelKLEIN

All-Purpose BoxKLEIN

K

© 1996 TELEWIRE SUPPLYK77

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionA popular choice for all-around use. Big capacity box with thenecessary strength and rigid construction. Ample three com-partment tote tray with big, easy-grip handle. Double draw boltsplus hasp and staple for lock shackles up to 3/8" diameter

DescriptionThe J1024 Throwing Weight will attach to any hand line forgoing through trees and other rope-throwing operations. Onepound of lead captivates a wire eye and is enclosed in a 3/4"wall of foam rubber.

DescriptionLightweight, 9" level with plumb, level and 45° mitre vials.Level vial is side and top reading.

1-1/2" x 5/8" aluminum body has hanging hole and magnetizedstrip on bottom.

Ordering Information

Order Mfg.No. No. Size WeightJKS 052806 J-101 Three inch diameter 1 lb.

Ordering Information

Order Mfg.No. No. Size WeightKLN 032920 54401 20"L x 9-1/2"H x 8-1/2" deep 12 lbs.

Ordering Information

Order Mfg.No. No.KLN 007961 930-9

Page 79: TWS Sec_K

Tools & Safety EquipmentHand Tools

DescriptionFour models for wire and cable diameters up to 1/2". All steelwith chrome finish and jam proof construction. Grooved guideand blade position tacker. Set staples without damage to wire.

Folding Hex Key SetsKLEIN

Staple GunsARROW

K

© 1996 TELEWIRE SUPPLY K78

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionFit pocket or tool box. Heat-treated chrome-nickel alloy steel.Wrench ends are square cut and chamfered for easy inser-tion and secure fit. Holder serves as a handle. Wrenches canbe used straight out or at a right angle for extra leverage.Nine Key Set.

Ordering Information

Order Mfg. Key HandleNo. No. Lengths Length

KLN 007944 70591 11-1/16" to 3-1/2" 4-1/4"

Sizes: 5/64", 3/32", 7/64", 1/8", 9/64", 5/32", 3/16", 7/32" and 1/4"

Ordering Information

Order Mfg. Wire StapleNo. No. Dia. LengthsARW 007889 T-18 3/16" 3/8," 7/16"

ARW 007890 T-25M 1/4" 3/8," 7/16," 9/16"

ARW 022301 T-37 5/16" 9/16"

ARW 007892 T-75 1/2" 9/16," 5/8," 7/8"

Tack-pointed staples

ARW 009797 T-18-3/8 3/8" T-18"

ARW 022172 T-18-7/16 7/16" T-18"

ARW 020350 T-25-3/8 3/8" T-25"

ARW 009806 T-25-7/16 7/16" T-25"

ARW 009809 T-25-9/16 9/16" T-25"

ARW 022302 T-37-9/16 9/16" T-37"

ARW 009811 T-75-9/16 9/16" T-75"

ARW 009812 T-75-5/8 5/8" T-75"

ARW 009813 T-75-7/8 7/8" T-75"

All packages 5,000 per box except T75, 1,000 per box.

Page 80: TWS Sec_K

DescriptionCuts tubing of hard or soft copper, brass, aluminum and thinwall conduit. Cuts cleanly without burrs or tubing distortion.Flare cut-off grooves on rollers permit cutting directly behind acracked flare without waste. Long-life alloy cutter wheels.Retractable, hardened reamer blade built-in, locks open orclosed. Capacity: 1/8" to 1-1/8" OD. Painted, enclosed feedmechanism to protect threads against dirt and damage. Extracutter wheel in knob.

Tools & Safety EquipmentHand Tools

Push DrillKLEIN

Bit BracesKLEIN

DescriptionRugged, all-steel, spring-action push drill. Chrome plated.Finely cross knurled handle and chuck collar for non-slip grip.Handle magazine holds drill bits, slides down on shaft for easyselection. Notched drill bits will not pull out of chuck whendrilling. Complete with 8 drill bits: 1/16", 5/64", 3/32", 7/64",1/8", 9/64", 5/32" and 11/64".

Length with drill bit: 11-1/2"

Tubing Cutter SUPERIOR

DescriptionStrong, nickel-plated steel body with smooth, tough Cycolachandle and head. Ball-bearing, steel-reinforced head. Positiveratchet action. Spring-loaded alligator jaws hold square tapershank bits, small and medium size drills. Chuck housing finelycross knurled.

K

Ordering Information

Order Mfg.No. No.KLN 007863 64002

Replacement Bit Set

KLN 007865 64003

Eight notched drill bits in sizes listed above.

© 1996 TELEWIRE SUPPLYK79

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.SPR 007846 35218

Ordering Information

Order Mfg.No. No.KLN 007802 64004 10" sweep

KLN 007800 64005 12" sweep

Page 81: TWS Sec_K

K

Tools & Safety EquipmentWorker Safety

Description4-1/2" cuff. Specially designed for durability. Strap on thumb foradded strength and protection. Davey tips to prevent ripping offingers. Seams reinforced. Sewed out seam. Elastic back.

DescriptionMedium weight Buckskin glove with short cuff. Strong anddurable. sewed out seam. Elastic back.

Ordering Information

Order Mfg.No. No. SizeRed Cowhide

GLO 007176 120 8-1/2

GLO 007184 120 9

GLO 007191 120 9-1/2

GLO 007197 120 10

GLO 007203 120 10-1/2

GLO 007211 120 11

Buckskin Medium Weight

GLO 007170 148 8

GLO 007178 148 8-1/2

GLO 007185 148 9

GLO 007192 148 9-1/2

GLO 007198 148 10

GLO 007204 148 10-1/2

GLO 007213 148 11

Buckskin Ex. Heavy Weight

GLO 007171 150 8

GLO 007179 150 8-1/2

GLO 007186 150 9

GLO 007193 150 9-1/2

GLO 007199 150 10

GLO 007205 150 10-1/2

GLO 007214 150 11

Lineman’s & Bridgeman’s Foreman’s Style GlovesGauntlet Gloves

© 1996 TELEWIRE SUPPLY K80

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. SizeGLO 007173 390 8

GLO 007181 390 8-1/2

GLO 007188 390 9

GLO 007195 390 9-1/2

GLO 007201 390 10

GLO 007207 390 10-1/2

GLO 007216 390 11

Sizing GlovesProper sizing is important for comfort. To determine the correctsize, measure the circumference of the worker’s hand belowthe base of the fingers, on a line parallel to the finger crotches,passing through the thumb crotch. Add one inch. Please statethe size when ordering

Small . . . . . . . . . . 8 — 8-1/2

Medium . . . . . . . . . 9 — 9-1/2

Large . . . . . . . . . . . 10 — 10-1/2

Xtra-Large . . . . . . . 10 —11-1/2

Page 82: TWS Sec_K

K

Tools & Safety EquipmentWorker Safety

Gauntlet Protector Gloves Lineman’s Rubber Gloves

DescriptionWorn over high voltage rubber gloves. Gun cut pattern (noseam between palm and thumb). Curved hand design. Glovecomes with 3" cuff. 12" overall length. These gloves meetOSHA requirements when used with our E-114-B or E-214-BRubber Lineman’s Gloves. If you wear a size 9 rubber glove (E-214-B). A size 9 (1057-3) protector glove will fit over it.

DescriptionCurved Hand

Available in AC Proof-Test voltage rating of 10 or 20KV, corresponding to Classes 1 and 2 respectively.

Length: 14"

Class 1 - 10 KV Class 2 - 20 KV

Ordering Information

Order Mfg.No. No. SizeGLO 201908 1057-3 9

GLO 201909 1057-3 9-1/2

GLO 201910 1057-3 10

GLO 201911 1057-3 10-1/2

GLO 201912 1057-3 11

GLO 201913 1057-3 12

© 1996 TELEWIRE SUPPLYK81

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Size

Class 1, 10KV Test Voltage, 7500 AC Maximum Use Voltage - Solid Black

GLV 007222 E-114-B 9

GLV 007223 E-114-B 9-1/2

GLV 007224 E-114-B 10

GLV 007225 E-114-B 10-1/2

GLV 007226 E-114-B 11

USE A

GLOVE BAG

TO PROTECT YOUR

INVESTMENT IN

SAFETY !

Order Mfg.No. No. Size

Class 2, 20KV Test Voltage, 17000 AC Maximum Use Voltage

GLV 007232 E-214-B 9

GLV 007233 E-214-B 9-1/2

GLV 007234 E-214-B 10

GLV 007235 E-214-B 10-1/2

GLV 007236 E-214-B 11

GLV 032692 E-214-B 12

Page 83: TWS Sec_K

K

Tools & Safety EquipmentWorker Safety

DescriptionShockgard® headband holds the shell in place on the head,supports the shell away from the head to maintain a minimum1-1/4’’ crown clearance and, in case of impact, works togetherwith the shell to absorb energy.

Has 4 plastic mounting clips that fit into 4 molded slots in theshell. Headband encircles the head and can be adjusted forsizes 6-1/2’’ to 7-3/4’’.

DescriptionLook boss on the pole and be safe. This is the one realLinemen wear. Designed especially for workmen exposed toelectrical hazards. One-piece shell provides limited head pro-tection in general use as specified in the performance require-ments of ANSI Z89.1-1981 Class B, and the nonmetallic con-struction offers high dielectric strength (non-conduction of elec-trical current).

Injection molded of polycarbonate in a smooth-crown design.Consist of shell and suspension.

Rubber Glove BagBASHLIN

Shockgard Lineman’s HatMSA

Hard HatMSA

© 1996 TELEWIRE SUPPLY K82

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionStandard white cotton duck. Bellows type top opening. Aleather spot is sewn to the cotton duck and the snap is in turnriveted to the leather. Has printed reminder to "Always UseYour Gloves". Double sewn with ventilation and drain holes inbottom. Heavy duty button snaps on flap. Riveted or bar tackedat points of strain. Strong snap with cast tongue.

Ordering Information

Order Mfg.No. No. Size WeightBSH 006907 24-LB 17" x 8" 12oz.

®

Ordering Information

Order Mfg.No. No. ColorHatMSA 007256 459184 White

MSA 007258 459186 Yellow

CapMSA 007104 455123 White

MSA 007109 455126 Yellow

Ordering Information

Order Mfg.No. No.

MSA 007261 454232

Hat Shown

Page 84: TWS Sec_K

DescriptionSpectra® safety glasses with a replaceable one-piece lens pro-vides an uninterrupted field of vision and ideal protection. Lenscan be easily changed to reduce replacement costs. Universalnose bridge fits comfortably; temples are easily adjusted. Facial-contoured permanent side shields offer outstanding protection.Specially designed durable plastic frame prevents lens fromcontacting rough surfaces. Meets or exceeds ANSI Z87.1-1989.Clear lenses.

DescriptionRegular One-Piece Zero Hood LinerCan be worn alone or under protective hats and caps. Coverhead, neck and ears. Velcro adjustable chinstrap. Has wind andwater repellent gray poplin outer material and washable suedeinner material—both fast-dyed materials. Meets specificationsof both ANSI Z89.1 and Z89.1B.

K

Tools & Safety EquipmentWorker Safety

Elastic Chinstrap AssemblyMSA

Protective Goggles

Winter LinerMSA

DescriptionWith Plastic Hooks & BuckleComplies with ANSI Z89.1 and OSHA regulations.

Safety Glasses

DescriptionGeneral-purpose cover-type protective goggles of soft vinylplastic. Comfortable and shaped to conform to facial contours.Fit easily over personal glasses. Top and bottom edges perfo-rated for direct ventilation. Clear one-piece .060" acetate lensis replaceable. Lightweight adjustable elastic strap. MeetsANSI Z87.1 1989 & CSA Z94.3.

Ordering Information

Order Mfg.No. No.MSA 007264 88128

© 1996 TELEWIRE SUPPLYK83

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.MSA 007270 86092

Ordering Information

Order Mfg.No. No.SFT 141617 11130031

Ordering Information

Order Mfg.No. No.SFT 007250 11210050

Page 85: TWS Sec_K

Tools & Safety EquipmentWorker Safety

DescriptionTwo cell D size orange industrial safety flashlight with safetyhead and ring hanger. UL and MSHA approved. Alsoapproved for hazardous locations.

Industrial Magnetic FlashlightRAY-O-VAC

Hand-LightPortable Fluorescent Hand LightsJAMESON

DescriptionFeatures Sturdy high impact barrel with magnet. Grease andchemical resistant; non-conductor of electricity; large slip-proof switch; brilliant beam, perfect spot. Uses No. PR2 bulb.Uses two "D" Cell batteries (not included.)

Industrial Safety FlashlightRAY-O-VAC

DescriptionHeavy duty 115 VAC portable fluorescent hand lights with auto-matic start are completely insulated, with no exposed metalsurfaces. They maintain excellent handling temperatures with-out generating excess heat. Reflectors are glare-free silvermylar; shield is shatterproof high impact plastic.

K

Ordering Information

Order Mfg.No. No. Description

RYV 096385 H22M handyman magnet flashlight

© 1996 TELEWIRE SUPPLY K84

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. DescriptionRYV 135103 IN2-MS safety flashlight

Ordering Information

Order Mfg. Cord LightNo. No. Length Length Weight

JMS 094733 30-1550-HD 50' 24-1/2" 5 lbs.

JMS 094735 30-3050-HD 50' 42-1/2" 8 lbs.

Page 86: TWS Sec_K

Description6-volt sealed beam lantern provides portable battery pow-ered, high intensity light. Fully chromed steel gauge con-struction. Comes with sealed beam bulb in verticaladjustable swivel head.

Tools & Safety EquipmentWorker Safety

Floating Beam LanternRAY-O-VAC

Hard Hat LightFULTON

DescriptionIncludes heavy-duty metal switch and switch protector;Available with or without battery.

Sportsman LanternRAY-O-VAC

DescriptionFulRay™ Hard hat light is Velcro fastened to hard hat; matingVelcro piece included for hat. Features Magna-Beam™ flood-light reflector that covers 10 times larger work area than stan-dard reflectors. Water resistant, ABS plastic external parts (noexposed metal), safety yellow body. Slide ON-OFF switch.Uses PR-7 bulb. Uses 3 AA cell replaceable batteries. Alkalinebatteries recommended for longer use life.

K

Ordering Information

Order Mfg.No. No. DescriptionRYV 096387 L295-B w/o battery

RYV 137207 L295-S with battery

© 1996 TELEWIRE SUPPLYK85

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Description

RYV 096388 301 Complete with No. 918 6-volt battery.

Ordering Information

Order Mfg.No. No.FLT 149391 6200-B

Page 87: TWS Sec_K

Batteries First Aid Kits

K

Tools & Safety EquipmentWorker Safety

© 1996 TELEWIRE SUPPLY K86

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order NedaNo. No. Volts Type CellBAT 055625 15F 1.5 Flashlight AA

BAT 034624 15D 1.5 Heavy Duty AA

BAT 032372 15A 1.5 Alkaline AA

BAT 023863 24F 1.5 Flashlight AAA

BAT 035696 24A 1.5 Alkaline AAA

BAT 009753 14F 1.5 Flashlight C

BAT 029708 14A 1.5 Alkaline C

BAT 009754 13F 1.5 Flashlight D

BAT 027058 13A 1.5 Alkaline D

BAT 009756 908 6 Carbon . . . . .

BAT 034300 915 6 Carbon . . . . .

BAT 009758 918 6 Carbon . . . . .

BAT 009759 903 7.5 Carbon . . . . .

BAT 020627 1611 9 Carbon . . . . .

BAT 153229 1604AC 9 Alkaline . . . . .

Ordering Information

Order Mfg.No. No. DescriptionFAD 023335 610-112 10 unit kit

FAD 023334 616-121 16 unit kit

FAD 023341 624-133 24 unit kit

10 16 24Contents Unit Kit Unit Kit Unit Kit

Steel unit cabinet 1 1 1

Strips, 1" x 3" unit 16's 2 3 3

X-tra large bandage, 6's 1 2 2

Tape, spool 1/2" x 5 yds 0 0 1

Compress bandage, 4" unit 1 2 3

Gauze compress unit, 24" x 72" 0 1 2

Gauze pad 3" x 3", unit 0 0 1

Bandage, gauze 4" x 6 yds 0 1 1

Triangle bandage, double box 1 1 2

Burn cream. 1/8oz. foil pk., 6/bx 1 1 1

PVP wipes, 10's 1 2 3

Cold pack, small, unit 0 0 1

Tourniquet and forceps unit 1 1 1

Ammonia inhalants, 10/box, unit 1 1 1

First aid instruction card 1 1 1

Latex gloves, 1pair/bag 1 2 3

Page 88: TWS Sec_K

DescriptionHeavy duty nylon vinyl coated florescent orange open weavemesh. Highly reflective yellow phosphorescent vertical stripeson front and back. Two snaps on front, and adjustable elasticside straps. Extra long front and back provide maximum visibil-ity day or night. 48" overall.

Tools & Safety EquipmentWorker Safety

Wasp & Hornet KillerBLACKBURN / THOMAS & BETTS

Snap-Front Safety Vest

DescriptionKills wasps, hornets and yellow jackets from as far as 20 feetaway. Saturating nests, hiding and breeding places inhibitstheir return. Also kills spiders and tent caterpillars. For useindoors or outdoors. Net weight: 16 oz.

Our Best Snap-Front Safety Vest

DescriptionA more economical model 39" length overall. Elastic on eachside, snaps on front. Single coated vinyl on cotton base.Vertical white phosphorescent stripes.

K

Ordering Information

Order Mfg.No. No.BBN 108025 15-700

© 1996 TELEWIRE SUPPLYK87

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.SFT 201907 880MXY

Ordering Information

Order Mfg.No. No.SFT 007425 600

Page 89: TWS Sec_K

Tools & Safety EquipmentWorker Safety

High Visibility Rainsuits

Plastic Barricade Tape

DescriptionHas heat sealed seams for waterproofing and is resistant tomost chemicals. PVC vinyl, laminated to a cloth base. Parkawith a detachable hood, double fly front, double ventilated back,snap cuffs & drawstring waist. Overalls have adjustable snapcuffs and snap fly. Orange color.

Emergency Warning Triangle

DescriptionConveniently packed in a self-dispensing box. Easily unwindsfrom center of box. 9" diameter. Weight: 3 lbs. Approximately1" wide. 1000' roll. Fluorescent red color.

K

Ordering Information

Order Mfg.No. No. DescriptionRGR 007346 8117-S small

RGR 007347 8117-M medium

RGR 007348 8117-L large

RGR 007349 8117-XL X-large

RGR 153257 8117-XXL XX-large

© 1996 TELEWIRE SUPPLY K88

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionEmergency warning triangle with each leg made of fluorescentorange day-glo material with hi-intensity reflective area for nighttime warning. Triangle disassembles and folds flat in its own stor-age case. Meets or exceeds Federal Specification: FMV55-125

Ordering Information

Order Mfg.No. No. DescriptionSFT 140982 99 ET Set of three triangles and case

Ordering Information

Order Mfg.No. No.SFT 036254 1X1000

Page 90: TWS Sec_K

DescriptionSame cone as above with reflective collar or collars. Reflectors meet MUTCD requirements.

Tools & Safety EquipmentWorker Safety

Traffic Cones

After Market Reflective Collars

DescriptionCones are manufactured of 100% Polyvinyl Chloride (PVC).Brilliant fluorescent orange color for maximum daytime visibili-ty. One-piece construction with white liner for enhanced visibil-ity. Contain UV absorbers to retain brilliance and assureextended life. Remain rigid in hot weather. Won’t slump or sageven at 150°F. Custom logos can be imprinted. Ask your salesrepresentative for details.

Traffic Cones with Reflective Collars

DescriptionHighly reflective glue on collars meetMUTCD requirements.

• A 18" cone will use one 6" collar.• A 28" cone will use a 4" and 6" collar

together to give two reflective bands.

K

Ordering Information

Order Mfg.No. No. Height WeightSFT 007431 18POWB 18' 3 lbs.

SFT 007432 28POWB 28' 7 lbs.

© 1996 TELEWIRE SUPPLYK89

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Description

SFT 132173 18PO-9805 18' high with 6" reflective collar

SFT 132199 28PORC64 28' high with 2 reflective collars

Ordering Information

Order Mfg.No. No. DescriptionSFT 132202 99R6C-18 6" reflective collar for 18" traffic cone

SFT 132201 99R4C2-28 4" reflective collar for 28" traffic cone

SFT 132204 99R6C-28 6" reflective collar for 28" traffic cone

SFT 136568 99AJ Adhesive for reflective collars, 1 pint jar

Page 91: TWS Sec_K

Tools & Safety EquipmentWorker Safety

Reflective Roll-Up Signs

Sign & StandGENERAL MACHINE PRODUCTS

DescriptionHigh visibility reflective roll-up signs are heavy duty, com-pact and durable. Superior protection is provided byhigh/visibility material. Imprinted with "Work Area Ahead" or"Utility Work Ahead".

K

Ordering Information

Order Mfg.No. No. DescriptionSFT 133982 JRU36R 36" X 36" “Work Area Ahead”

SFT 133983 JRU48R 48" x 48" “Work Area Ahead”

SFT 201905 JRU36R 36" x 36" “Utility Work Ahead”

SFT 201906 JRU48R 48" x 48" “Utility Work Ahead”

© 1996 TELEWIRE SUPPLY K90

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Tripod for Roll-Up Signs

Order Mfg.No. No. Description

SFT 133984 JSTRIM-JSTADP heavy duty 14 lb. tripod stand with 3 flag holders on top

SFT 133985 JSTREM-JSTADP 9 lb. tripod stand with 3 flag holders on top(same as above but 5 lbs. lighter)

Ordering Information

Order Mfg.No. No. Description

GMP 007480 11210 30" x 30" reflectorized sign imprinted with "Work Area Ahead" and stand

Page 92: TWS Sec_K

K

Tools & Safety EquipmentWorker Safety

Paddle SignDescriptionFor controlling traffic. 18" diameter with 6" high letters.Shapes and colors are easily recognized by motorists. Made of lightweight engineer grade sheeting, weatherproofand corrosion resistant.

DescriptionHigh visibility fluorescent colors sewn with dacron thread forsuperior weather resistance, greater resistance to chemicalsand maximum strength.

Fluorescent Flags

Ordering Information

Order Mfg.No. No. DescriptionSFT 007491 ST-SL 18" stop/slow sign with 18" handle

© 1996 TELEWIRE SUPPLYK91

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. DescriptionSFT 007444 216 16" x 16" (staff length 32")

SFT 007445 218 18" x 18" (staff length 32")

SFT 007446 224 24" x 24" (staff length 36")

Page 93: TWS Sec_K

K

Tools & Safety EquipmentPower Tools

Cordless Drill/Driver KitMAKITA Description

2-speed gear selection with variable speed in either range forboth drilling and driving in wood, metal and plastic. Variablespeed for pinpoint hole positioning and easy starting of screws.Low speed 0-400 RPM or high speed 0-1,100 RPM. Drills 3/8"in steel and 11/16" in wood. Electric brake stops chuck fast andhelps prevent stripping of screw heads. Kit includes battery,charger and tool case.

DescriptionThis tool offers dual action capabilities. Hammer drills or drillonly at the flick of a lever. Drills up to 350, 3/8" holes in 1" thickwood from a single one hour charge. Overload protector safe-guards against motor burnout. Professional quality and powerare built in. Operates on 9.6 VDC battery. Kit includes battery,charger and tool case.

3/8" Cordless Hammer Drill Kit ReversibleMAKITA

Ordering Information

Order Mfg.No. No. DescriptionMAK 109674 6093DW Cordless drill/driver kit

MAK 136220 6095DW Cordless drill/driver kit. Same as 6093DW but with keyless chuck.

MAK 112157 632007-4 9.6 volt battery

© 1996 TELEWIRE SUPPLY K92

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. DescriptionMAK 150527 8402VDW cordless hammer drill

MAK 112157 632007-4 9.6 volt battery

Page 94: TWS Sec_K

K

Tools & Safety EquipmentPower Tools

3/8" DrillMAKITA Description

Heavy duty, industrial quality 3/8" drill for the most difficult oftasks. Variable speed 0-1200 RPM. 3.0 Amp motor. Drills up to3/8" in steel and 3/4" in wood. Compact, lightweight (3.3 lbs.)and well balanced for ease of operation. Double reductiongearing for efficient power transmission. All ball bearing con-struction for long tool life. Heavy duty industrial drill chuck.Double insulated for operator safety.

DescriptionFast and easy drilling in a wide variety of materials. Featureshigh speed, variable speed (0-2,100 RPMs) and a powerful 2.8Amp motor. Drills 3/8" in steel or 5/8" in wood. Compact andlightweight (3.1 lbs.) for easy handling. All ball bearing con-struction for durability and long tool life. Speed adjusting knoband lock-on button. Double insulated for operator safety.

3/8" Reversible DrillMAKITA

Ordering Information

Order Mfg.No. No.MAK 136222 6510LVR

© 1996 TELEWIRE SUPPLYK93

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.MAK 136221 6404

Page 95: TWS Sec_K

K

Tools & Safety EquipmentPower Tools

3/8" Hammer DrillMAKITA Description

Heavy duty 4 Amp hi-tech motor. 0-2700 RPM variablespeed and reversing feature for optimum flexibility. Two toolsin one - quick disengagement of hammer-drilling and drill-only mode. Lightweight (3.5 lbs.) design. Ball bearing con-struction. Heavy duty chuck for positive bit retention. Doubleinsulated for operator safety.

DescriptionHeavy duty 5.2 Amp motor. 0-850 RPM for drilling 1/2" insteel and up to 1-3/8" in wood. Lightweight (4.4 lbs.) andwell-balanced for ease of operation. Cool and efficient oper-ation with reduced noise level. Conveniently located revers-ing switch and lock-on button. Side handle can be attachedto either side for better control. Belt clip keeps drill handy atall times. Ball and needle bearing construction for durability.Forget-me-not chuck key retainer system. Double insulatedfor operator safety.

1/2" Variable Speed Reversible DrillMAKITA

Ordering Information

Order Mfg.No. No.MAK 137706 NHP1030W

© 1996 TELEWIRE SUPPLY K94

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.MAK 136224 6303

Page 96: TWS Sec_K

K

Tools & Safety EquipmentPower Tools

1/2" Reversible DrillMAKITA Description

Heavy duty, industrial quality 1/2" reversible drill for the mostdifficult jobs. Powerful 5.2 Amp high-tech motor combined with550 RPMs for superior power and torque. Ball and needlebearing construction for long tool life. Double insulated for oper-ator safety. Equipped with a convenient rocker type reversingswitch and heavy duty industrial chuck. Complete with largeside handle depth gauge, industrial quality chuck and key.

DescriptionHeat treated and hardened gears are housed in a nylon encap-sulated aluminum gear box for quiet, cool and safe operation.Constructed with ball and needle bearings throughout. Thehammers are made of high nickel alloy. Variable speed - 120Volts, AC only. No load speed: 0-1300 RPM; no load blows:20,800 BPM. Standard equipment: 1/2" industrial chuck withkey, side handle and depth rod. Weight: 4 lbs. 1/2" capacity inconcrete, 3/8" capacity in steel.

1/2" Heavy Duty ReversibleElectric Hammer DrillA.E.G

© 1996 TELEWIRE SUPPLYK95

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.MAK 136223 6301LR

Ordering Information

Order Mfg.No. No.AEG 038619 SBE-10RL

Page 97: TWS Sec_K

K

Tools & Safety EquipmentPower Tools

1/2" Hammer DrillMAKITA Description

Makita's 1/2" hammer drill is like having two tools in one. Itdrills with or without hammering action at either 0-800 or 0-2,000 RPM. Delivers 0-8,800 or 0-2,200 blows per minute.Heavy duty 4.8 Amp motor for long tool life. Compact andlightweight pistol grip design for easy handling. Double insu-lated for operator safety.

DescriptionSharing the same physical characteristics as the SBE-10RLabove, this unit has a new high power efficient motor withpower input of 600 Watts and output of 300 Watts. Preciseanchor setting is accomplished through forward and reversehammering. Provides high speed or high torque. Variablespeed -120 Volts AC only. No load speed: 0-1250/3,000 RPM;no load blows: 20,000/48,000 BPM. 2-speed synchromeshgear box. Standard equipment: 1/2" industrial chuck with key,side handle, depth rod and key retainer.

1/2" Heavy Duty Reversible Electric Hammer DrillA.E.G

© 1996 TELEWIRE SUPPLY K96

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. WeightMAK 137707 NHP1310 4.5 lbs

Ordering Information

Order Mfg.No. No. WeightAEG 101683 SB-2E-16RL 4.75 lbs

Page 98: TWS Sec_K

DescriptionAn ideal tool for construction and utility crews as well as manyother drilling applications. The high-torque engine delivers 1.3h.p. for greater drilling capability. The heavy duty gear case has20:1 reduction speed which provides for variable drillingspeeds. It also features a unique "gear-locking" mechanism,allowing the entire unit to be rotated in the event that the bitbecomes bound during use. 10.9 lbs., clutch is centrifugal, drill

Tools & Safety EquipmentPower Tools

Light-Duty Gasoline Chain SawsHOMELITE

Extension Cords

DescriptionFor light trimming, climbing, felling small trees, or occasionalmedium duty work. Uses Power Tip guide bar 14" long.

Two cycle engine with solid state ignition and a displacement of1.9 cubic inches. Automatic chain oiling. Safety tip standard onall saws. For use with Raker III™ semi-chisel series 37chromed chain. Dual trigger throttle.

Chain oil capacity, 6.1 ounces; fuel-oil mix capacity, 8.5 ounces.

1/2" Gas Powered DrillJACKSON

K

© 1996 TELEWIRE SUPPLYK97

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.HLT 093620 Super 2

Ordering Information

Order Mfg.No. No.JKS 138126 1513-262L

Ordering Information

Order Mfg. CordNo. No. TypeCXT 140087 EC500730, 50' High visibility NUFLEX‚

CXT 140088 EC500735, 100' High visibility NUFLEX‚

CXT 008891 EC100730, 50' All purpose flat vinyl

CXT 008892 EC100735, 100' All purpose flat vinyl

DescriptionsUL listed, meets OSHA requirements. Professional heavy dutyround vinyl. High visibility NUFLEX‚ jacket protects againstrough use, oil grease, chemicals, moisture, ozone and givesadded flexibility at below freezing temperatures. Molded onand bonded vinyl plugs and connectors won't break or pull offcord. 3 conductor, 300 Volts grounding. 14/3 GA, SJTW-A.Orange color.

All purpose flat vinyl. Jacket protects against rough use, oilgrease, chemicals, moisture, ozone and gives added flexibilityat below freezing temperatures. Molded on and bonded vinylplugs and connectors won't break or pull off cord. 3 conductor,300 Volts grounding. 14/3 GA, SJTW-A. Orange color.

Page 99: TWS Sec_K

K

Tools & Safety EquipmentPower Tools

© 1996 TELEWIRE SUPPLY K98

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Redi-Line Electric Generator Redi-Line Electric GeneratorPACIFIC-SCIENTIFIC PACIFIC-SCIENTIFIC

DescriptionDC to AC 500 to 900 WattsGet 120 volt true sine-wave AC power from battery or DCpower source. Energy saving feature results in generator run-ning only when power is required (power tool trigger or appli-ance switch). Constructed from durable materials. Can bemounted in any position with minimum space required. No airpollution. Operates quietly in confined areas. Built-in circuitbreaker prevents damage from overloads. Generator hascapacity to deliver surge-current above its rated output whenmomentary extra starting power is needed. Incorrect connec-tion to generator terminals will not damage unit. Acceptableambient temperature of -30°F(-34°C) to +130°F (+54°C).

SpecificationsInput

DC Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Output

Watts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 VACAmps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hz

Battery RecommendationsType . . . . . . . . . . . . . . . . . . . . . . . . . . . . deep cycle/marineCapacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Amp

Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 AmpsElevation Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . noneLength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-3/8"Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1/8"Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5/8"Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 lbs.

Ordering Information

Order Mfg.No. No.RNC 024651 DA-12A-500Variance from 120V, 60 Hz is dependent on load size and DC input voltage

DescriptionDC to AC 1600 WattsGet 120 volt true sine-wave AC power from battery or DCpower source. Energy saving feature results in generator run-ning only when power is required (power tool trigger or appli-ance switch). Constructed from durable materials. Can bemounted in any position with minimum space required. No airpollution. Operates quietly in confined areas. Built-in circuitbreaker prevents damage from overloads. Generator hascapacity to deliver surge-current above its rated output whenmomentary extra starting power is needed. Incorrect connec-tion to generator terminals will not damage unit. Acceptableambient temperature of -30°F to +130°F (-34°C to +54°C).

SpecificationsInput

DC Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Output

Watts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1600Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 VAC Amps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Hz

Battery Recommendations Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . .deep cycle/marine Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Amp

Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 AmpsElevation Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . .noneLength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-3/4"Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5/8"Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1/2"Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 lbs.

Ordering Information

Order Mfg.No. No.RNC 153467 DA-12L-1600 Variance from 120V, 60 Hz is dependent on load size and DC input voltage

Page 100: TWS Sec_K

K

Tools & Safety EquipmentDrill Bits

Bell Hangers Drill Bits Tip-Top Rotary Masonry Drill BitsIRWIN RELTON

DescriptionAvailable with tapered square shanks for hand brace or roundshanks for electric drill, with small hole in tip for pulling wire.Regular head drills made of premium 100 carbon bearing steel.Carbide head drills made of 61 carbon tool steel with carbidecutting tip.

Ordering Information

Order Mfg. Overall BitNo. No. Length Diameter

No. 818R drill bit with round shank for use in wood

IRW 009996 39104 18" 1/4"

IRW 007703 39105 18" 5/16"

IRW 007710 39106 18" 3/8"

IRW 034190 39107 18" 7/16"

IRW 021516 39112 18" 3/4"

No. 818T brace bit with taper square shank for use in wood

IRW 007697 38604 18" 1/4"

IRW 007704 38605 18" 5/16"

IRW 007712 38606 18" 3/8"

IRW 007717 38607 18" 7/16"

No. 824R drill bit with round shank for use in wood

IRW 119835 39407 24" 3/8"

No. 824T brace bit with taper square shank for use in wood

IRW 007714 38706 24" 3/8"

No. C818R carbide tipped drill bit with round shank for use inmasonry

IRW 007698 40004 18" 1/4"

IRW 007705 40005 18" 5/16"

IRW 007711 40006 18" 3/8"

IRW 034344 40008 18" 1/2"

No. C818Tcarbide tipped brace bit with taper square shank for use in masonry

IRW 007713 39806 18" 3/8"

© 1996 TELEWIRE SUPPLYK99

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionSingle-cutter type for drilling all types of masonry.Recommended for low-cost drilling. Special carbide cutter pen-etrates quickly with minimum pressure. Recommended drillingspeeds; below 1/4" diameter, 550-900 RPM; 1/4" to 1/2" diam-eter, 450-700 RPM; above 1/2" diameter, 350-500 RPM.

Ordering Information

Order Mfg. Bit ShankNo. No. Diameter Diameter LengthRLT 145397 TT-3-4 3/16" 11/64" 4"

RLT 040810 TT-4-6 1/4" 1/4" 6"

RLT 007732 TT-4-18 1/4" 1/4" 18"

RLT 007740 TT-5-18 5/16" 5/16" 18"

RLT 007746 TT-6-18 3/8" 3/8" 18"

RLT 007748 TT-6-24 3/8" 1/4" 24"

DescriptionDesigned for placement of drop wire through floors and wallsup to 12" thick. The use of fluorescent plastic helps in locatingthe unit in dim light. Plastic tubing, packed 5 per package.

Ordering Information

Order Mfg.No. No.JKS 1519 1519

Drop Cable Guide 1519JACKSON

Page 101: TWS Sec_K

Tools & Safety EquipmentDrill Bits

DescriptionDesigned for use as percussion bits in lightweight rotating-vibrating hammers, but can be used equally well in standarddrill motors as rotary bits. A special, hard, tough carbide cutteris precisely located for maximum support and strength.

Drill Bit SetsHANSON / IRWIN

Nail Eater Power BitsGREENLEE

Description635 series heavy duty high speed steel drill bits. Metal indessets

Ram-Tip Rotary Percussion BitsRELTON

DescriptionMade of super tough, heat treated steel to cut through nails andprovide long tool life. The self-feeding single twist allows foreasy chip removal and fast boring.

K

Ordering Information

Order Mfg. # ofNo. No. Pcs SizeIRW 201942 63536 13 1/16" through 1/4" by 64ths.

IRW 201941 63537 15 1/16" through 1/2" by 32nds.

IRW 201943 63538 29 1/16" through 1/2" by 64ths.

IRW 201944 63548 29 1/16" through 1/2" by 64ths. with 3/8" reduced shank

© 1996 TELEWIRE SUPPLY K100

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Bit ShankNo. No. Diameter Diameter Length

RLT 137713 RT-4-18 1/4" 1/4" 18"

RLT 137712 RT-5-18 5/16" 1/4" 18"

RLT 137711 RT-6-18 3/8" 3/8" 18"

RLT 137710 RT-6-24 3/8" 3/8" 24"

Ordering Information

Order Mfg. Twist Hex Overall No. No. Length Shank LengthGRN 105184 66PT N 3/4 15" 7/16" 18"

GRN 105185 66PT N 11/16 15" 7/16" 18"

Page 102: TWS Sec_K

K

Tools & Safety EquipmentDrill Bits

Solid Center Carpenter Brace BitsIRWIN

DescriptionFor all around carpenter work, especially where long holes arerequired. Forged from special bit steel, solid center type, heattreated full length and oil finished.

Double cutter; 12" twist. Average overall length 18".

DescriptionWith Adapter Shank

Single twist type with single spur, cutter and side lip. Mediumfast screw pitch. Made of highly polished special analysis steelwith full polished finish. Adapter shank fits both hand bracesand power drills.

No. 415

Standard length. Has 12" twist and 6" shank. Overall length,18". Recommended for boring through creosoted poles withoutclogging, binding or stopping to clear chips. Also for boringlarge timbers used in heavy construction work.

No. 416Extra long. Has 18" twist and 6" shank. Overall length, 24".Recommended for boring extra large poles and any otherjobs where extra deep holes are required.

Pole BitsIRWIN

© 1996 TELEWIRE SUPPLYK101

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Size

IRW 007642 47706 3/8"

IRW 007673 47711 11/16"

Ordering Information

Order Mfg.No. No. SizeNo. 415:

IRW 007643 46606 3/8" x 18"

IRW 007666 46610 5/8" x 18"

IRW 007674 46611 11/16" x 18"

IRW 007681 46612 3/4" x 18"

IRW 007687 46613 13/16" x 18"

No. 416:

IRW 007677 46711 11/16" x 24"

5/8" Hardware requires an 11/16" hole.

3/4" Hardware requires an 13/16" hole.

Page 103: TWS Sec_K

K

Tools & Safety EquipmentCrimpers

Hex Crimp ToolsCABLEMATIC - RIPLEY Description

A crimp tool for every application. Established compression adjustmentfor longer life and trouble free performance. Fully adjustable heat treat-ed star wheel does not require removal.

Repair KitKit includes 1 star wheel, 1 star wheel screw, 2 links, a 1/16" hexwrench, 6 retaining rings, 4 pins and 4 bow washers.

Ordering Information

Order Mfg. Major MinorNo. No. Hex Hex Use OnUTU 112672 CR-596QL .360 .324 59, 6, universal

UTU 147451 CR-360 .360 .N/A universal

UTU 112679 CR-211CX .475 .100 11

UTU 100829 CR-596Q .384 .324 7, 59, 6

UTU 042442 CR-596R .324 .262 59, 6,

UTU 150464 CR-EZT N/A N/A EZF - 6, 59

UTU 137708 CR-596QLR .360 .324 Full Cycle

UTU 147452 CRKMK-1 Repair Kit

© 1996 TELEWIRE SUPPLY K102

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Digicon Radial Tapered CrimperANTEC Description

The new Digicon High Performance Crimp Tool is designed foruse with Antec’s Digicon Connector, creating an environmental-ly resistant, perfectly round 360° crimp. It doubles holding powerand pull out strength over standard Hex connectors. TheDigicon High Performance stripper is designed for use with theDigicon High Performance Crimp Tool.

Ordering Information

Order Mfg.No. No. DescriptionANT 202442 DHP-Tool Crimper

ANT 202443 DHP-Stripper Stripping Tool

ANT 202444 DHP-Pouch Tool Pouch

Page 104: TWS Sec_K

K

Tools & Safety EquipmentCrimpers

Hex Crimp ToolsBEN HUGHES - CABLE PREP

© 1996 TELEWIRE SUPPLYK103

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionTop grade steel and stringent quality control measures bringyou a cost effective, quality long life crimp tool. This tool has abuilt in adjustment feature.

Ordering Information

Order Mfg. Major MinorNo. No. Hex HexBHG 119081 HCT-USA .360 N/A

BHG 095946 HCT-986 .360 .324

BHG 084468 HCT-611 .410 .324

BHG 036525 HCT-659 .324 .262

BHG 042357 HCT-660 .384 .324

BHG 146963 HCT-902 .475 .324

BHG 122733 HCT-116 .472 .324

BHG 112677 HCT-214 .470 .162

BHG 108673 HCT-360 .384 N/A

BHG 043364 HCT-211 .475 N/A

Hex Crimp Repair Kit

BHG 042890 MK-1050

Terminx®

DescriptionThe Terminx has a new compression mechanism thatensures the required force is applied to fully activate yourcompression type connectors, guaranteeing a secure droptermination. The Terminx works with both 6 and 59 seriescompression type connectors. The T-5000-EZF tool comeswith a tip for the EZF connector. Other tips are available formost compression type connectors.

Ordering Information

Order Mfg.No. No.BHG 201938 T-5000-EZF

Page 105: TWS Sec_K

Tools & Safety EquipmentCrimpers

DescriptionTwo quick and easy steps to prepare RG59 and RG6 cables.Tool closes to the correct cutting pressure. Insert cable whereindicated and rotate. Remove cable, reinsert at second cuttinglocation and rotate. Procedure produces a 1/4" x 1/4" prep.Makes a minimum of 1,500 cuts. Weight: 2 oz.

Coaxial Wire StripperBEN HUGHES - CABLE PREP

Coaxial Wire StrippersXCELITE

DescriptionOne step operation to strip RG59, RG6 or RG11. Tool removescable jacket, cuts foil and braid, and exposes the center con-ductor in one step. Non-adjustable. Color-coded.

Cable StripperCABLEMATIC

DescriptionSave time for the novice user who is stripping primarily justone or a few cables in the same general O.D. range. A hexwrench is included for adjustment to other size cables.Simple instructions.

K

Ordering Information

Order Mfg.No. No. Description

BHG 130887 CPT-6590 1/4" prep for RG59 and RG6 series cables

BHG 154947 CPT-1250 1/8" prep for RG59 and RG6 series cables

BHG 154946 CPT-1100 1/4" prep for RG11 series cables

BHG 130886 RBC-6590 Replacement blade

© 1996 TELEWIRE SUPPLY K104

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.RTA 149680 8200

Ordering Information

Order Mfg.No. No. DescriptionCOO 033657 2CS5962-B 2 step for cable 58, 59, 6

COO 033772 2C-B replacement cassette (blades)

Page 106: TWS Sec_K

DescriptionThe EZF cable preparation tool assures an easy and accuratecable prep each time. The tool removes the cable jacket,scores foil and braid all in one step, and also exposes the cor-rect length of center conductor. The consistent quality is aproven labor saver by reducing future service calls. The EZFcable preparation tool will last for thousands of applications.

Tools & Safety EquipmentCrimpers

Coax Cable StrippersCABLEMATIC - RIPLEY Description

Machined to precision tolerances. Simple two step operationfor perfect stripping every time. Strips cable to same dimensionevery time without nicks or scratches. Saves time, preparescable for connector in less than 15 seconds. Lifetime use.

EZF ToolsRAYCHEM

K

Ordering Information

Order Mfg.No. No. Cable ConnectorUTU 112704 UT-1100 RG-11/U "F"

UTU 008167 CB60 Replacement blades

© 1996 TELEWIRE SUPPLYK105

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

®

Ordering Information

Order Mfg.No. No. Description

RYC 083293 EZF-T Cable prep tool for RG-59 & RG-6

RYC 102370 EZF-Tool Cable prep tool for RG-11

RYC 083292 EZF-BP Replacement blade pack for RG-59/6 tool

RYC 102371 EZF11-BR Replacement blade pack for RG-11 tool

Crimp Tool TestDescriptionWith wear or improper use, the crimp tool may notclose correctly, To ensure that the crimp tool is clos-ing properly, insert a piece of paper into the tip ofthe jaws WHILE CRIMPING A CONNECTOR. Thepaper should be held tightly by the crimp tool. Thistest should be performed periodically. If the crimptool fails this test, adjust crimp tool jaws per manu-facturer’s instructions.

Close up view of crimp tool papertest. Jaws should hold the paper

Paper

Page 107: TWS Sec_K

Tools & Safety EquipmentCrimpers

DescriptionEnsures proper insertion of F connector onto cable.Connector screws onto and off of tool. Hand held.Machined threads.

DropSaver™ Environmental ProtectorRAYCHEM

Flaring ToolCABLEMATIC - RIPLEY

DescriptionThe DropSaver environmental protector is installed in an EZF®-59, EZF-6, and EZF-11 connector when the connector is dis-connected. When used with an EZF sealing sleeve (suppliedwith DropSaver) it environmentally seals the connector to cableinterface against water and corrosion, and protects the con-nector threads. The DropSaver is easy to remove when serviceis restored, and it is reusable.

Insertion ToolCABLEMATIC - RIPLEY

DescriptionFlaring (expander) tools are designed to flare drop cables foreasier installation of the "F" connector on the cable. Whenproperly used, this tool will alleviate the bunching of aluminumtape behind the connector and is a must for flaring bonded con-struction-type cables.

K

Ordering Information

Order Mfg.No. No.RYC 099178 Dropsaver

© 1996 TELEWIRE SUPPLY K106

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.UTU 137709 IT-59/6/11

Ordering Information

Order Mfg.No. No. Flares CablesUTU 045105 FT-59 RG-59/U

UTU 112707 FT-6 RG-6/U

Page 108: TWS Sec_K

Description"F" connector installation tool made of 360 aluminum alloy.Full length cut-out for easy removal of cable. For RG59 andRG6 connectors.

Tools & Safety EquipmentTorque Wrench

Torque WrenchJACKSON

Security Sleeve ToolsGILBERT/LRC /CROWN

"F" Connector Installation ToolTEL-CON

K

© 1996 TELEWIRE SUPPLYK107

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Order Mfg. ShaftNo. No. length.CBP 135095 SWU716 2.125"

LRC 041446 SST-59U .630"

CAT 603028 SS-TOOL 1.625"

GIL 042514 SS-TL 1.62"

Ordering Information

DescriptionFor F fittings. 40 inch pounds.

Ordering Information

Order Mfg.No. No.JKS 140009 1514

Ordering Information

Order Mfg.No. No.TEL 108718 TCRG59

Page 109: TWS Sec_K

K

Tools & Safety EquipmentCable Caddies

Cable Caddies 1201, 1203 & 1204JACKSON

© 1996 TELEWIRE SUPPLY K108

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionThese units are used to pull off drop cables and in all sizes; lightweightand durable. The 1203 and 1204 models have wheels. The 1204 willalso hold two reels at the same time.

Order Mfg. Reel Quantity LoadNo. No. Size Per Pkg. SizeJKS 020082 1201 18" x 15" One 100 lbs. gross

JKS 020331 1203 26" x 15" One 200 lbs. gross

JKS 1204 1204 18" x 15" One 200 lbs. gross

Ordering Information

1201 1203 1204

Page 110: TWS Sec_K

K

Tools & Safety EquipmentCoring Tools & Accessories

Combination Coring / Stripping ToolCABLEMATIC - RIPLEY

DescriptionCore and strip coaxial cable in one operation. Designed formanual use or comes with the 3/8" power adapter to use in adrill. Manual operation is made easy with the "T" handle andeven easier with the "R" model ratchet tools. No need toremove your hand during operation. All sizes are color-codedfor easy identification. All metal construction.

Ordering Information

Order Mfg.No. No. SizeUTU 041877 CST-412 .412

UTU 041882 CST-412R .412

UTU 041878 CST-500 .500

UTU 041881 CST-500R .500

UTU 112587 CST-500MC .500

UTU 112667 CST-500MCR .500

UTU 147798 CST565TXR .565

UTU 088759 CST-625 .625

UTU 049767 CST-625R .625

UTU 112590 CST-650MC .650

UTU 041879 CST-750 .750

UTU 041880 CST-750R .750

UTU 112592 CST-750MC .750

UTU 112669 CST-750MCR .750

UTU 112606 CST-840TXR .840

UTU 101006 CST-875 .875

UTU 057958 CST-875R .875

UTU 112597 CST-2100MC 1.00

UTU 101002 CST-21000R 1.00

UTU 118938 CST-1160TXR 1.16

© 1996 TELEWIRE SUPPLYK109

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Order Mfg. FitsNo. No. ToolUTU 041883 CB114K CST-412/R

UTU 041884 CB115K CST-500/R

UTU 147453 CB132K CST-500MC/R

UTU 112722 CB130K CST-500QRR

UTU 146048 CB143K QR-540/R

UTU CB-146K CB146K CST-565TX/R

UTU 112713 CB116K CST-625/625/R

UTU 041885 CB117K CST-750/R

UTU 147371 CB134K CST-750MC/R

UTU 112714 CB138K CST-840TX/R

UTU 112724 CB127K CST-860Q/R

UTU 112715 CB118K CST-875/875/R

UTU 112716 CB156K CST-21000/R

Replacement Sheath Cutting Blade

Order Mfg.No. No. Description

UTU 112739 CB-60B (1 blade) For CST-412 through CST-875 and all QRT tool kits

UTU 008167 CB-60 (2 blades) For CST-2100 and CST-21160

Replacement coring blades for CST tool

Page 111: TWS Sec_K

Tools & Safety EquipmentCoring Tools & Accessories

DescriptionThe CCT guided coring tool incorporates a front guiding featureto eliminate all lateral cable movement. The result is consistentprecision coring without scoring the center conductor or cableshield. The new non-clogging blade cores foamed polyethyl-ene cable to the depth of all standard insert sleeves. Theimproved fluted body design assures a firm grip. All metal bodyconstruction. Models are color-coded for easy identification.

Guided Coring ToolsCABLEMATIC - RIPLEY

K

© 1996 TELEWIRE SUPPLY K110

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Order Mfg. FitsNo. No. ToolUTU 041218 CB101 CCT-3412

UTU 041219 CB102 CCT-3500

UTU 041221 CB104 CCT-3750

UTU CB-105 CB105 CCT-3875

UTU 603260 CB106 CCT-31000

Ordering Information

Order Mfg.No. No. StandardUTU 040984 CCT-3412 .412

UTU 040988 CCT-3500 .500

UTU 040985 CCT-3625 .625

UTU 040986 CCT-3750 .750

UTU 040987 CCT-3875 .875

UTU 040983 CCT-31000 1.000

Order Mfg.No. No. Color ToolUTU 079756 29104 black CST-412/CCT-3412

UTU 073041 29105 red CST-500/CCT-3500

UTU 088760 29106 blue CST-625/CCT-3625

UTU 109750 29111 green CST-750/CCT-3750

UTU 112727 29112 yellow CST-875/CCT-3875

UTU 112728 29113 orange CST-1000/CCT-31000

Replacement Guide Sleeves

Replacement coring blades for CCT tool

Page 112: TWS Sec_K

K

Tools & Safety EquipmentCoring Tools & Accessories

Combination Stripping / Coring ToolsBEN HUGHES - CABLE PREP

DescriptionThe CABLE PREP stripping/coring tool accomplishes two func-tions in one operation. This tool strips aluminum sheathedcoaxial cable and cores the dielectric foam, leaving the cablefully prepared to accept a connector. The SCT tool reducescable preparation time by almost fifty percent. This tool can beoperated manually or with a variable speed drill. No adaptersmust be purchased.

The blade is made from high alloy tool steel and the housingis molded of high impact, lightweight, wear and chemicalresistant resin.

DescriptionThe RTH-4500 Ratchet T Handle is an accessory tool for theBen Hughes coring and stripping/coring tool line. The mainte-nance-free, noiseless ratchet helps perform coring or strip-ping/coring of coaxial cable by establishing a positive torque inthe core direction. Easy to install, the RTH-4500 adapts to anycoring tool with a 3/8" shaft with three flats.

Ratchet T HandleBEN HUGHES - CABLE PREP

© 1996 TELEWIRE SUPPLYK111

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Order Mfg.No. No. Cable SizeBHG 041354 SCT-412 .412

BHG 041358 SCT-500 .500

BHG 077861 SCT-500QR .500QR

BHG 077862 SCT-540QR .540QR

BHG 146967 SCT-565TX .565TX

BHG 041357 SCT-625 .625

BHG 154951 SCT-700TX .700TX

BHG 154953 SCT-715QR .715QR

BHG 041356 SCT-750 .750

BHG 146968 SCT-840TX .840TX

BHG 091915 SCT-860QR .860QR

BHG 041355 SCT-875 .875

BHG 091916 SCT-1125QR 1.125QR

Ordering Information

Order Mfg.No. No. ToolBHG 146965 SC-412-RB for SCT-412 tools

BHG 112749 SC-500-RB for SCT-500 tools

BHG 112755 SC-540-QR for SCT-540QR tools

BHG 112750 SC-625-RB for SCT-625 tools

BHG 112751 SC-750-RB for SCT-750 tools

BHG 112757 SC-860-QR for SCT-860 tools

BHG 112752 SC-875-RB for SCT-875 tools

BHG 112753 SC-1000-RB for SCT-1000 tools

Ordering Information

Order Mfg.No. No.BHG 118112 RTH-4500

Replacement blades for SCT tool - Jacket Stripper & coring all inone piece

Page 113: TWS Sec_K

K

Tools & Safety EquipmentCoring Tools & Accessories

Coring ToolsBEN HUGHES - CABLE PREP

DescriptionThe Cable Prep DCT Coring Tool has been designed for fast,efficient coring of coaxial cable. The blade does not clog, allow-ing more installations per day. The coring tool has a non-break-able handle of high technology polymer for greater impactstrength — without added weight.

The DCT Coring Tool can be used manually with the T-Bar han-dle or for power operation by removing the T-Bar to expose adrill shaft. No special adapters are required.

The DCT Coring Tool is designed for all generations of foamedpolyethylene cables. It is insulated for activated splices and iscolor coded by size for identification. The DCT Coring Tool isideal for flooded cables.

Combination Coring / Stripping Tool KitsCABLEMATIC - RIPLEY

© 1996 TELEWIRE SUPPLY K112

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Order Mfg.No. No. Cable SizeBHG 037039 DCT-412 .412

BHG 037040 DCT-500 .500

BHG 038601 DCT-625 .625

BHG 037041 DCT-750 .750

BHG 040038 DCT-875 .875

BHG 057302 DCT-1000 1.000

Ordering Information

Order Mfg.No. No. ToolBHG 146964 RB-412 DCT-412

BHG 038049 RB-500 DCT-500

BHG 112758 RB-625 DCT-625

BHG 038050 RB-750 DCT-750

BHG 122746 RB-875 DCT-875

Order Mfg.No. No.BHG GS-412 GS-412

BHG 602753 GS-500

BHG GS-750 GS-700

BHG GS-875 GS-875

DescriptionCombination coring/strip tool kit for Commscope QuantumReach (QR) cable. Operation is made easy with the "T" handleand even easier with the "R" ratchet tools. All metal construction.

Order Mfg.No. No. StandardUTU 151307 QRT-500 .500QR

UTU 151306 QRT-500R .500QR

UTU 141796 QRT-540 .540QR

UTU 149394 QRT-540R .540QR

UTU 141797 QRT-860 .860QR

UTU 149393 QRT-860R .860QR

Ordering Information

Replacement blades

Replacement guide sleeves for DCT / SCT Ben Hughes Tools

Page 114: TWS Sec_K

K

Tools & Safety EquipmentCoring Tools & Accessories

SST Cable Preparation ToolsCABLEMATIC - RIPLEY

DescriptionFor coaxial cables with dielectrics of foam polyethylene, gasinjected poly, mc2 and fused disc.

The SST-A assures a uniform trim every time without nicksor scratches and a smooth, square cut without burrs. Thealuminum shield is never distorted permitting trouble-freeinstallation of the connector. A precision vernier adjustmentenables the installer to vary the length of the center conduc-tor from 1/2" to 2".

The SST-A has been modified to accept standard foam poly,gas injected and fused disc cables. The unit leaves a smallamount of dielectric on the center conductor.

DescriptionFor removing aluminum sheath and polystyrene (Dynafoam) orfoamed polyethylene (Parameter II) dielectric.

No blade ever touches the center conductor, eliminating thepossibility of nicks. Because the DST cuts from the inside out,it never distorts or squashes the shield. A precision vernieradjustment enables you to vary the length of the exposed cen-ter conductor from 1/2" to 2", to accept any connector.

DST Cable Preparation ToolsCABLEMATIC - RIPLEY

Ordering Information

© 1996 TELEWIRE SUPPLYK113

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Order Mfg.No. No. StandardUTU 008140 SST-412A .412

UTU 008142 SST-500A .500

UTU 048928 SST-625A .625

UTU 008144 SST-750A .750

UTU 048926 SST-875A .875

UTU 024285 SST-1000A 1.000

Order Mfg.No. No. ToolUTU 043371 CB30A SST-412A

UTU 043371 CB30A SST-500A

UTU 043372 CB31A SST-625A

UTU 043372 CB31A SST-750A

UTU 112737 CB32A SST-875A

Ordering Information

Order Mfg.No. No. Cable SizeUTU 008131 DST-500 .500

UTU 008132 DST-750 .750

Replacement blades - Includes coring bit & sheath cutting blade

Page 115: TWS Sec_K

K

Tools & Safety EquipmentCoring Tools & Accessories

Jacket StrippersCABLEMATIC - RIPLEY Description

JST cable preparation instruments are ideal for removing thejackets of any CATV trunk and distribution cable includingflooded cables and cables with oversized jackets. What makesthese tools unique is that the blades never touch the aluminumshield. A gentle clockwise rotation of the instrument removesexactly enough jacket to prepare the cable for removal of theshield and dielectric.

DescriptionRemoves the jackets of .412, .500, .625, .750 .875 and 1.000trunk and distribution cable. Removed jacket feeds away fromyour hand rather than over the top. Blade angle allows maxi-mum jacket removal to-prepare the cable for coring.

Jacket StripperBEN HUGHES - CABLE PREP

© 1996 TELEWIRE SUPPLY K114

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. StandardUTU 008134 JST-412 .412

UTU 008136 JST-500 .500

UTU 112700 JST-500MC2 .500MC2

UTU 038600 JST-625 .625

UTU 008137 JST-750 .750

UTU 100333 JST-875 .875

UTU 061216 JST-1000 1.000

Replacement blade for all JST tools

UTU 036966 CB6667

Ordering Information

Order Mfg.No. No.BHG 154948 JCS-500

BHG 154949 JCS-625

BHG 154950 JCS-750

Page 116: TWS Sec_K

DescriptionUsed to remove dielectric and adhesive from center conductorsof all coaxial cables, from .412 through super-trunk. Scrappersare reversible and can be sharpened with a fine file. Handle ismade of plated spring steel with a comfortable plastic coating.Weight: 5 oz.

Tools & Safety EquipmentCoring Tools & Accessories

Center Conductor CleanerCABLEMATIC - RIPLEY

Tubing CutterSUPERIOR

DescriptionFor removing residual dielectric from the conductor of all sizesof trunk and feeder cables without scratching or nicking. Fingergrippers permit application of maximum force. V-shaped scrap-ing notches on cleaner blades assure fast, effective removal of

Center Conductor CleanerJACKSON

K

Ordering Information

Order Mfg.No. No.UTU 150471 CC-100

Replacement blade for CC-100

UTU 150706 16722

© 1996 TELEWIRE SUPPLYK115

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionCuts tubing of hard or soft copper, brass, aluminum and thinwall conduit. Cuts cleanly without burrs or tubing distortion.Flare cut-off grooves on rollers permit cutting directly behind acracked flare without waste. Long-life alloy cutter wheels.Retractable, hardened reamer blade built-in, locks open orclosed. Capacity: 1/8" to 1-1/8" OD. Painted, enclosed feedmechanism to protect threads against dirt and damage. Extracutter wheel in knob.

Ordering Information

Order Mfg.No. No.SPR 007846 35218

Ordering Information

Order Mfg.No. No.JKS 1520 1520

Page 117: TWS Sec_K

Tools & Safety EquipmentConstruction Tools - Lashers

DescriptionFor Aerial Cables up to 3-1/4" Diameter on SuspensionStrands from 1/4" to 7/16"

Can lash cable suspension strand from 1/4" to 7/16". Can bereadied for dual lashing merely by depressing the strand rollerknob and rotating it a quarter turn. Lasher will hold (2) 1200'coils of .045" lashing wire at one loading.

Operable easily by one man. Features built-in brake to preventbackroll. All-range tensioning device assures traction on thestrand. Rear cable lifter assembly provided positive locking action.

Complete with pulling rope and No. 8189 case.

C Cable LasherGENERAL MACHINE PRODUCTS

Lashing Wire & Figure Cable GripJACKSON

DescriptionFor Cables up to 1-3/4" Diameter on Suspension Strandsfrom 1/4" to 3/8"

Holds (2) 1200' coils of .045" lashing wire at one loading.Provides a smooth, non-chafing, even lashing which alwaysstays tight. Equipped with brake to prevent backroll when lash-ing cable upgrade.

Complete with pulling rope and No. 7143 case.

J2 Cable LasherGENERAL MACHINE PRODUCTS

DescriptionP/N 1503-F8 is designed to align strand & cable with pole linehardware holding figure 8 cable to the pole for 1/4" strand and3/4" cable or smaller. Crescents new 7" grip with easy unlock-ing. Made of cold rolled steel, finished with zinc plating.

K

Ordering Information

Order Mfg. Lasher Case TotalNo. No. Weight Weight Weight

GMP 009197 71420 33 lbs. 16 lbs. 49 lbs.

© 1996 TELEWIRE SUPPLY K116

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. WeightJKS 086142 1503 (top) .75 lbs.

JKS 1503-F8 1503-F8 (bottom) .75 lbs.

Ordering Information

Order Mfg. Lasher Case TotalNo. No. Weight Weight Weight

GMP 009200 86070 46 lbs. 16 lbs. 65 lbs.

Page 118: TWS Sec_K

Description(Also referred to as a pole mount), this tool is used to set upeither a 45° or 90° Corner Block. or a cable chute at the pole. Itis installed quickly and safely by attaching the snaps to thestrand on either side of the three body clamp, then tighteningthe strap around the pole. A safety clip provided on the verticalshaft keeps the other tools secured to the Pole Bracket, and pre-vents accidents. Made of welded steel, heavy duty ratchet andstrap, 9-1/2" shaft and painted. Packed one per box.

Tools & Safety EquipmentConstruction Tools

Set-Up Bracket/JSU Series JACKSON

Adapter 1060JACKSON

DescriptionFast & economical, the JSU mid-span set-up bracket combinesthe benefits of light weight, strength and convenience. It is usedwith the Jackson 45° Corner block to guide as many as fourcables from trailer to strand. The bracket swivels for properalignment and is quickly attached with strand clamp, snap andknob included. Made of steel and finished with primed andpainted enamel. Packed one per box.

Pole Bracket 1044 with Heavy Duty Ratchet AssemblyJACKSON

DescriptionThe p/n 1060 Adapter is designed to be used with the p/n 1044& 1044-F Pole Bracket, p/n 1059 Strand Chute Bracket and p/n1035 45° Corner Block. Basically. its purpose is to convert avertical axis to a horizontal axis. It is an interchangeable part,used throughout the tool system. Made of welded tubular steeland painted. Packed one per box.

K

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 030594 JSU-1 7 lbs. one

© 1996 TELEWIRE SUPPLYK117

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 042833 1044 11 lbs. two

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 600616 1060 2 lbs. two

Page 119: TWS Sec_K

Tools & Safety EquipmentConstruction Tools

DescriptionUsed to raise cable in position for lashing to strand. Aluminumcasting shoe with steel insert for wear, suspended by steelstraps for two strand rollers locked on the strand. Ideal tool inconstruction using cable up to 2-3/4" diameter.

Cable Chute 1058JACKSON

Corner Block 1035JACKSON

DescriptionThe 1058 cable chute consists of a single bar mid-span setupbracket equipped with a friction free cable chute. This setuppermits cables to be pulled from the cable reel when lined upwith a strand mounted cable block. Made of steel and highimpact synthetic material. Finished with zinc plating, blackenamel, nylon rollers. Packed one per box

No. G1012 Aerial Cable GuideGENERAL MACHINE PRODUCTS

DescriptionUse as a chute for corners. (Also referred as a 45°). The cornerblock is used when pulling a cable around an inside or outsidecorner of up to 45°. Plastic sheaves support the cables throughthe bend, preventing tangling and kinking. Adjustable idlerrollers keep the cables in the proper sheaves. The block is usedwith p/n 1044 Pole Bracket for pulling a corner at the pole, andit can be used as a chute along with p/n 1044 and 1060 Adapterat the pole. It can also be used as a mid-span cable chute whencombined with p/n 1059 strand Chute bracket and p/n 1060Adapter, or the JSU series setup brackets. The standard 1035is set up for two 1" and two 3/4" cables. Replacement rollers areavailable as large as 1-1/4" in diameter.

K

© 1996 TELEWIRE SUPPLY K118

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 100176 1058 6.5 lbs. one

Ordering Information

Order Mfg.No. No.GMP 009027 70055

Ordering Information

Order Mfg.No. No.JKS 042829 1035

Page 120: TWS Sec_K

Tools & Safety EquipmentConstruction Tools

Corner Block 1019JACKSON

Fiber Optic Corner BlocksJACKSON

DescriptionPull longer runs without splicing; fits cable as large as 1" jacket-ed. (Also referred to as "90"). Similar to p/n 1035 45° CornerBlock, this tool is used to pull up to four cables around an insideor outside corner up to 90°. It is used with p/n 1044 Pole Bracketfor pulling corners at the pole. Some corners are mid-span or ata floating corner. Use p/n 1019 with p/n 1061 Crossover Braceto pull cables around these types of corners. The standard 90°Corner Block is set up for two 2-1/4" and two 3/4" cables.Replacement rollers as large as 1-1/4" are available.

Description45° and 90° corner block for fiber optic cables. Use withJackson pole bracket (Order No. JKS 042833).

K

Ordering Information

Order Mfg.No. No.JKS 042827 1019

© 1996 TELEWIRE SUPPLYK119

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.JKS 143531 1035-F, 45°

JKS 143532 1019-F, 90°

Page 121: TWS Sec_K

K

Tools & Safety EquipmentConstruction Tools

Cable Puller 1080JACKSON Description

For total control and protection of cable. (Also referred to asdolly, jig or sled). The multiple cable puller designed to solvethe problem of pulling more than one cable. This tool, in twoversions, will pull up to nine (9) cables permitting them to swiv-el independently and preventing tangling. A strand brake pre-vents the puller from backing out when the pullout tensionstops, thus preventing the cables from sagging between multi-ple cable blocks or at the pole. The p/n 1080 multiple cablepuller stays on the strand, regardless of the towing angle, andis shaped to fend off tree branches. Eyelets are designed tobreak at 325 lbs. before damage occurs to cable.

DescriptionThis heavy duty cable puller rolls freely over existing cable bun-dles up to 2-3/4" in diameter. For coaxial and fiber optic cable.Will not break lashing wire. Pulls as many as four cables.Pulling eyes swivel to prevent tangling. Rugged design andplacement. Prevents damage to existing coaxial cables. Madeof welded steel frame, with Lexan* 101 roller and finished withzinc plating. Packed one per box.

Overlash Cable Puller 3080JACKSON

Ordering Information

Order Mfg.No. No. DescriptionJKS 042842 1080 For 3/8" to 1/4" strand

JKS 036347 1080-1 For 5/16" to 1/2" strand

© 1996 TELEWIRE SUPPLY K120

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Qty, PerNo. No. Weight CrewJKS 122732 3080 8 lbs. One

Page 122: TWS Sec_K

DescriptionRugged, fast, fits 1/4" and 5/16" strand. The Cable block push-er, or "shotgun", is used during multiple cable lashing when acable positioner (p/n 1067) or multiple cable blocks (series1036) are used. Two shotguns are required when using a posi-tioner along with multiple cable blocks.

The tool is quickly attached or removed from the strand with aspiraling motion. There are absolutely no parts attached to thejackson cable block pusher to break or wear out. The highly vis-ible orange color also makes it easy to locate. Safe and non-conductive. Made of medium density polyethylene. Packedone per box.

Tools & Safety EquipmentConstruction Tools

Cable Block PusherGENERAL MACHINE PRODUCTS

Cable Positioner 1067-2JACKSON

DescriptionFor pushing D or F cable blocks along 1/4" to 7/16" diametersuspension strand during lashing operations. Consists of aslotted tube with semi-rotatable sleeves at each end which lockin open and closed positions. One end has a circular flange forbearing against lashing machine; other end bears againststrand hooks of the cable block. Cannot fall off while lashing.

Cable Block PusherJACKSON

DescriptionAlso called magic box or divider. 16" long each with two rollersfor 1/4" strand. Two holes 3/4" diameter. Place on strand infront of lasher. After placing cable in two 3/4" holes it locks shutwith two latches.

K

Ordering Information

Order Mfg.No. No.GMP 009250 70018

© 1996 TELEWIRE SUPPLYK121

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 078471 1092 2 lbs. Two

Ordering Information

Order Mfg.No. No.JKS 042837 1067-2

Page 123: TWS Sec_K

Tools & Safety EquipmentConstruction Tools

DescriptionThe heavy duty model has two adjustable friction surfaces forincreased braking action. The advanced design of the disc por-tion provides smooth, consistent resistance as cable or strandis dispensed from the reel. Made of welded steel, asbestosbrake pads, hardened set screws and finished with zinc plating.Packed one per box.

Reel BrakeJACKSON

Strand Brake 1079JACKSON

DescriptionFor both strand and cable reels. The reel brake is designed tocontrol the reels when dispensing cable or strand. This safetydevice prevents strand or cable from paying off the reel whenpull out tension stops. Strand dangling around the trailer is dan-gerous, and spilled cable can result in kinking and flattening.

Attach back-up collar to reel bar; slide reel onto bar; install spac-er if using tow reels; install disc and friction assembly and tight-en set screw; adjust braking pressure with aluminum knobs.

Reel Brake 2078JACKSON

K

Ordering Information

Order Mfg.No. No.JKS 042838 1078

© 1996 TELEWIRE SUPPLY K122

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 100753 2078 16 lbs. Two per trailer

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 042839 1079 1.2 lbs. Six

DescriptionFor total strand control. (Also referred to as a clamp or polebrake). It offers maximum control during strand placement. Thestrand brake is placed in the three bolt clamp between theclamps. This permits the strand to go in one direction only, pre-venting it from backing up.It swivels to accommodate slightcorners when pulling the strand. Placement of the brake is atevery fourth or sixth pole or every time you cross the street.Instead of the strand sagging all the way to the ground, with theuse of this devise it will only sag three to four feet betweenpoles, eliminating the possibility of the strand catching on itemssuch as mail boxes, gutters, car bumpers, tree limbs. In addi-tion to the obvious damage such instances can cause, whenthe strand comes loose, under such tension, it can pop up intopower lines and cause a power outage and/or a serious injury.We consider this tool a must for the proper and safe placementof strand. Made of welded steel, hardened steel brake surfaceand finished with zinc plating. Packed one per box.

Page 124: TWS Sec_K

DescriptionDesigned for grounding conductors up to and including336,000 CM ACSR while they are being strung. Made of alu-minum with aluminum axles and an aluminum attachment forthe ground line. Metal graphite spring loaded brushes on thetop sheaves ensure positive and continuous contact.

Tools & Safety EquipmentConstruction Tools

Strand Brake 1079-10JACKSON

Reel Buck J-1001JACKSON

DescriptionClip to the ground wire at the finest pole to act as a groundshould the strand short out the power. This tool protects thelinemen and personnel around the trailer. Made of ground wire,welded steel and hardened steel brake surface, finished withzinc plating. Packed one per box.

No. 336 Traveling GroundBASHLIN

DescriptionUsed to support cable or strand when a trailer is not available.Place reel bar in a strand or cable reel, place reel bucks on eachside of the reel and tilt back until the handles rest on the groundthis will pickup the reel so that you can pull out cable or strand.Made of welded steel tubing, primed and enamel painted.

K

© 1996 TELEWIRE SUPPLYK123

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 201443 1079-10 2.5 lbs. One

Ordering Information

Order Mfg.No. No. WeightBSH 007571 336 2.5 lbs. 8 oz.

Ordering Information

Order Mfg.No. No. WeightJKS 050249 J1001 60 lbs.

Page 125: TWS Sec_K

Tools & Safety EquipmentConstruction - Loop Forming Tools

DescriptionFor maximum support and minimum stress on cable duringbending. (Also referred to as a "bender" or "bending board").The biggest potential problem in installing coaxial cable is in theplacement of expansion and contraction loops required for alu-minum sheath cable. Coaxial cable MUST be kept round. Anydistortion of the cable will damage its ability to transmit signals.The unibend is constructed with four synthetic shoes whichallow the cable to slide without distortion as the proper radiusis formed mechanically.

P/N 1084 Unibend should be used to bend single cable sizesas large as 3/4" jacketed. The loop formed is 6" deep with a flatbottom length of 12". The flat bottom loop has been tested andproven to be a superior loop for maximum cable life. Eachradius formed by the synthetic shoes is 11", in keeping withcable manufacturer’s specifications. The entire loop is devel-oped over a length of 36 inches. No additional hand formingrequired. Made of welded steel, hardened steel on wear sur-faces, synthetic shoes, primed and painted blue enamel.Packed one per box. Maintenance: Lubricate gearbox compo-nents with light machine oil. Be sure to retract pawl from gearrack when opening tool after bend has been made.

Bender JM-100 & 200JACKSON Description

This tool is used to hand form feeder cables up to .540. Theloop is 12" flat bottom, 36" long, 6" deep and 11" radius. P/NJM-100 is for bending single cables while p/n JM-200 is forbending two cables at a time. Made of cold rolled steel andplastic, finished with zinc plating. Packed one per box.

Unibend 1084JACKSON

K

© 1996 TELEWIRE SUPPLY K124

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 043212 JM-100 5 lbs. One

JKS 043213 JM-200 5 lbs. One

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 042843 1084 18 lbs. One

Order Mfg.No. No. WeightJKS 07799 1021-.750 one 3/4" Teflon shoe

JKS 043043 1021-11 one 1" Teflon shoe

Replacement Parts:

Page 126: TWS Sec_K

DescriptionMake consistent long-life loops in cable impossible to bend byhand. P/N 1084-1 1" Bender is designed to bend all cable sizeslarger than 3/4" jacketed. The loop formed is 6" deep with a flatbottom length of 12". The radius formed by each of the syn-thetic shoes is 16". The entire loop is formed over a distance of51". Do not bend more than one cable with p/n 1084-1. Noadditional hand forming required. Made of welded steel, hard-ened steel on wear surfaces and 4 synthetic shoes. Finishedwith primer and painted with blue enamel. Packed one per box.Maintenance is the same as th p/n 1084.

Tools & Safety EquipmentConstruction - Loop Forming Tools

Double Bender 1084-0JACKSON Description

Prevent rippling or kinking of the aluminum sheath, while bend-ing 2 cables at once. With the p/n 1084-0 Double bender, youcan bend two cables with diameters as large as 3/4" jacketed,at the same time. The loops are identical in size and shape tothe loop formed by the p/n 1084 Unibend. The flat bottom loophas been tested and proven to be a superior for maximum cablelife. Each radius formed by the synthetic shoes is 11", in keep-ing with cable manufacturer’s specifications. The entire loop isdeveloped over a length of 36". No additional hand formingrequired. Made of welded steel, hardened steel on wear sur-faces and 8 synthetic shoes. Finished with primer and paintedwith blue enamel. Packed one per box. Maintenance: Lubricategearbox components with light oil. Be sure to retract pawl fromgear rack when opening tool after bend has been made.

Single Bender 1084-1JACKSON

K

© 1996 TELEWIRE SUPPLYK125

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 042844 1084-0 19 lbs. One

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 042845 1084-1 24 lbs. One

Loop Forming ToolJACKSON Description

Cast in aluminum. Handles cable up to 1/2" jacketed or5/8" bare.

Ordering Information

Order Mfg.No. No. WeightJKS 008246 JTS-500 1 lb.

Page 127: TWS Sec_K

Tools & Safety EquipmentConstruction - Loop Forming Tools

DescriptionThe finest bender, the Jackson 2084-15, will bend 1" and 1-1/4"cables with consistent long-life loops impossible to bend byhand. No additional hand forming required. Made of weldedsteel, hardened steel on wear surfaces and 4 synthetic shoes.Finished with zinc plating. Packed one per box. Maintenance isthe same as p/n 1084.

Double Bender 2084JACKSON

Double Bender 2084-15JACKSON

K

© 1996 TELEWIRE SUPPLY K126

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionThe finest bender design. The double 1" bender combines theadvantages of synthetic bending shoes, improved ratchet andgearbox design, durability, and speed for bending two .875" or1" cables at once. Large deep strand hooks make it easier toquickly form proper flat bottom expansion loops in any cableconfiguration, including over-lashed cables. The superiordesign of the 2084 helps prevent the formation of kinks or flatspots as the loop is formed. No additional hand forming isrequired. Made of welded steel, hardened steel on wear sur-faces and 4 synthetic shoes. Finished with zinc plating. Packedone per box. Maintenance is the same as p/n 1084.

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 079744 2084 33 lbs. One

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 056477 2084-15 37 lbs. One

DescriptionTRAQ™ cable blocks will accept 1" jacketed cable, and small-er sizes. TRAQ™ cable blocks are unquestionable the mostdurable cable blocks available today. Made from a high-impactresistant space-age material, TRAQ™ blocks are virtually inde-structible with just minimal care. TRAQ™ cable blocks aredesigned specifically for stringing television cable. Because oftheir compact size and lighter weight, they make the job easierand faster. And,TRAQ™ blocks will not move along the stranduntil the lasher pushes them. A unique "gate" makes theTRAQ™ block perfect for mid-span applications, too.

Cable BlocksTRAQ™

Ordering Information

Order Mfg.No. No. Size WeightMRW 116014 TRAQ 1 5" H x 3" W 3 oz.

MRW 041610 TRAQ 2 6" H x 4" W 6 oz.

MRW 042310 TRAQ 4 10" H x 4-12" W less than 12 oz.(handles 4 cables at once)

Page 128: TWS Sec_K

K

Tools & Safety EquipmentConstruction - Cable Blocks

Multiple Cable BlockJACKSON Description

The 1036-4 multiple cable block includes a patented, one-piece "cable retaining" system that allows it to be used totallyfrom the ground. Open the retainer and lock the block onto thestrand. After placing the cables into the individual rollers, closethe retainer with a quick downward pull by hand or with a layupstick. It also includes a strand lock designed to work on 1/4",5/16" and 3/8" strand. Multiple cable blocks should be usedat every pole and spaced every 30 to 40 feet in mid-span. The1036-4 supports 2 cables up to 1-1/4" jacketed along with 2cables up to 3/4" jacketed. Made of Lexan 101, stainless steel,high impact polyurethane rollers. Finished with zinc plating. Packed ten per box.

Description1515 Nylon Roller & 1516 Steel Roller. This cable block can beplaced over a package of cable and strand up to 1-1/2" in diam-eter. It will support any cable up to 1-1/2" in diameter. Availablewith plastic or steel rollers. The frame is made of spring steel.Finished with zinc plating. Packed 20 per box

Overlash Cable BlockJACKSON

Ordering Information

Order Mfg. Qty perNo. No. Weight Crew DescriptionJKS 073689 1036-4 2.5 lbs. 40-50 supports 2 cables up to 1-1/4" jacketed along with 2 cables up to 3/4" jacketed

JKS 1036-8 1036-8 3 lbs. 40-50 supports 4 cables up to 1-1/4" jacketed along with 4 cables up to 3/4" jacketed special rollerconfigurations are also available

JKS 041608 1036-4H with this space saving cable block you only need 9" and it has four 1" rollers on one bar.

© 1996 TELEWIRE SUPPLYK127

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Roller Qty. PerNo. No. Type Weight Crew

JKS 140011 1515 Nylon 10 lbs. 40

JKS 140014 1516 Steel 12 lbs. 40

Cable BlockJACKSON Description

This roller will hang over a cable and strand package of up to3" and has two 1-1/4" rollers. Light weight and durable. Madeof Lexan. Lexan frame, stainless steel cable retainer, and alu-minum rollers. Packed 10 per box.

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 008872 4011 1.5 lbs. 40

Page 129: TWS Sec_K

Tools & Safety EquipmentConstruction -Rollers

DescriptionSame as the 4010, but will support 2 cables up to 1-1/4" each.

Econo - Roller 4010 - FOJACKSON

Overlash Roller 4030 - FOJACKSON

DescriptionMade of high impact Lexan and will fit on 1/4" strand. Thisroller will hold up to 1-1/4" cable. Packed 20 per box

Econo - Roller 4020 - FOJACKSON

DescriptionThis roller will hang over a cable and strand package of up to3" and has two 1-1/4" rollers. Light weight and durable. Madeof Lexan. Lexan frame, stainless steel cable retainer, andnylon rollers. Packed 10 per box.

K

© 1996 TELEWIRE SUPPLY K128

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 043653 4010-FO .6 lbs. 40

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 043654 4020-FO 1 lb. 40

Ordering Information

Order Mfg. Qty. PerNo. No. Weight CrewJKS 043652 4030-FO 1.5 lbs. 40

Page 130: TWS Sec_K

K

Tools & Safety EquipmentConstruction - Cable Block

Cable Block JP-6J

JACKSON DescriptionWorks on 1/4", 5/6" and 3/8" strand. Supports telephone cableup to 2-3/4" diameter. The Lexan roller, p/n JP-6, includes a5/16" strand lock that works equally well on strand 1/4", 5/16",and 3/8". This feature makes it a universal tool for most CATVand telephone aerial construction. Its frame and roller aremolded in high impact plastic, with hardened steel on strandand bearing surfaces.

(Also referred to as a "silver dollar roller"). This tool is used tosupport a single cable prior to lashing. It locks onto the strand,and is released when struck by the cable block pusher or "shot-gun" placed ahead of the lasher. P/N JP-6 should not be usedas a cable puller, or as a block for pulling corner. It is lightweightand very durable due to the molded Lexan frame and 3" roller.

DescriptionFor cables ranging from 1/8" to 2-3/4" diameter. This is themost versatile cable block on the market today. The wire retain-er on the JP-12 keeps fiber optic cable as small as 1/8" diam-eter in the roller during typically low pulling tension. It also sup-ports paired telephone cable as large as 2-3/4", as well as anycoaxial cable size. The retainer closes as the variable strandlock is applied to strand sizes 1/4", 5/16" and 3/8". The frameand roller are molded in high Lexan plastic for increasedstrength, reduced weight, and economy.

Cable Block JP-12JACKSON

Ordering Information

Order Mfg.No. No.JKS 073688 JP-6

© 1996 TELEWIRE SUPPLYK129

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.JKS JP-12 JP-612

Page 131: TWS Sec_K

Tools & Safety EquipmentConstruction - Cable Block

K

© 1996 TELEWIRE SUPPLY K130

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

No. 8093 Cable BlockGENERAL MACHINE PRODUCTS

Ordering Information

Order Mfg.No. No.GMP 008874 8093

DescriptionSupports aerial cable on suspension strand prior to lashingcable, and can be used in dual lashing. Heat-treated frame.Strand hooks have steel inserts on bearing surfaces. Sheave isof heat-treated aluminum alloy with Oilite bearings.

DescriptionFor aerial cables to 2-3/4’’ diameter on suspension strandsprior to lashing cable. Heat-treated aluminum alloy frame.Strand hooks have steel inserts on bearing surfaces. Sheave isof heat-treated aluminum alloy with Oilite bearings. Lockinglever is reversible. Can be locked in either position so cable canbe pulled in the opposite direction.

No. 7268 D Cable BlockGENERAL MACHINE PRODUCTS

Ordering Information

Order Mfg.No. No.GMP 008869 7268

DescriptionDesigned for overlash of fiber optic or coaxial cables. Capacityof up to 2" bundles. Usable on 1/4" or 3/8" strand. Strong, elec-tro-galvanized steel frame, anti-friction roller and lever actuatedkeeper bar. Weight: 1.5 lbs.

Fiber Optic Overlash Cable BlockGMP

Ordering Information

Order Mfg.No. No.GMP 145234 70189

Page 132: TWS Sec_K

Tools & Safety EquipmentLayup Sticks

Fiberglass Pruner Handles /Layup SticksJAMESON

No. CL-1 Cable LifterJAMESON

DescriptionWill not splinter, spear back or absorb moisture. Have highdielectric properties and offer surface protection from harshultraviolet deterioration. Will interchange with all standard treetrimmer heads simply by using the Jameson Adapter System.

Wire Raising ToolJAMESON

DescriptionEnables craftsman to place aerial cable from the groundwith pruner handles. Takes cable up to 2-3/4". Fits FE or JE sticks only

K

Ordering InformationFG Series - Hollow Core

Order Mfg.No. No. Description

JMS 006827 FG6/3 set Comes with 1-3' section and 3-6' sections

© 1996 TELEWIRE SUPPLYK131

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionUsed for laying up steel strand, telephone and coaxial cable.Shaft slides into end of extension handle. No adapter needed.Fits FG or JE sticks only. Plated steel construction.

Ordering Information

Order Mfg.No. No.JMS 009298 WR-1

Ordering Information

Order Mfg.No. No.JMS 006814 CL-1

Order Mfg.No. No. Description

JMS 034899 JE6/3 set Comes with 1-3' section and 3-6' sections

Order Mfg.No. No. DescriptionJMS 006829 FG6 6' section

JMS 034898 JE6 6' section

JMS 006828 FG3 3' section

JE Series - Foam Core

Replacement Sections

Page 133: TWS Sec_K

Tools & Safety EquipmentLayup Sticks

DescriptionThese Multi-purpose tools are used to place cable blocks ontostrand, raise wire and cable.

1108-12This model has two steel tubes 1-1/4" (inside diameter) and 1-1/8" (outside diameter) permitting it to fit Jackson, Jamesonand Lemco lay-up sticks. No need to have two tools when onewill do and cost less than two.

1108-34These units fit on Jackson Tool Systems 1436 layup sticks, andare used to place cable roller mid-span and lock them intoplace. Will also fit Jameson and Lemco lay-up sticks.

SpecificationsMade of welded steel, finished with zinc plating. Packed oneper box

Fiberglass Layup SticksJACKSON Description

The Jackson 1436 is a set of three 6' sections made of high-strength fiberglass with a steel zinc plated female head. Anylifter equipped with a 1-1/4" diameter head that fits over thespring button.

Wire Raising Tool 1108 SeriesJACKSON

K

© 1996 TELEWIRE SUPPLY K132

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. WeightJKS 063752 1436 14 lbs.

Ordering Information

Order Mfg. Qty. perNo. No. Weight CrewJKS 201918 1108-12 1.5 lbs. one

JKS 201917 1108-34 1.5 lbs. one

Page 134: TWS Sec_K

DescriptionHeavy-duty, 1-1/2" capacity model No. 12 pruner head with three 6' by 1-3/4"diameter octagon wood poles and operating rope. A complete 18' pruner. Nosaw blade.

Tools & Safety EquipmentTree Saws & Pruners

Pruner Package - No. PH-9JAMESON

No. 20 PrunerSEYMORE SMITH

DescriptionVersatile 1-1/4" Side-cut pruner complete with removable 16"saw blade (SB-1T), canvas scabbard, 18' rope and PHA-9adapter for use with FG and JE poles.

No. 12 PrunerSEYMORE SMITH

K

Ordering Information

Order Mfg.No. No.JMS 100691 PH9

© 1996 TELEWIRE SUPPLYK133

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. Weight Description

SYM 009342 12-18 20 lbs. pruner and poles

SYM 009347 12 3 lbs. chain operated pruner head only. 1-1/2" capacity, malleable iron casting w/center cut action

JMS 006789 PHA #12 pole adapter to put #12 pruner head on the Jameson FG or JE poles

DescriptionCast aluminum No. 20 saw head with 16" saw blade and three 6' by 1-1/4"diameter octagon poles. A complete 18' pole pruning saw. No pruner head.

Ordering Information

Order Mfg.No. No. Weight Description

SYM 009342 20-18 12 lbs. saw and poles

SYM 032100 20 2 lbs. cast aluminum saw head only w/16" curved saw blade, hook for pushing branches & paint brush holder

JMS 006788 PHA #11 pole adapter to put #20 pruner head on the Jameson FG or JE poles

SYM 032101 20B 16" replacement pruning saw blade for No. 20

Page 135: TWS Sec_K

Tools & Safety EquipmentLayup Sticks

DescriptionThe wire raising tool and cable block lifter engage in the femaleend of the wood extension handle, and the spring-mounted pinlocks the tool on for use. Other sections lock on similarly fordesired length.

No. 6355 Wire Raising ToolGENERAL MACHINE PRODUCTS Description

With 2 hooks for placing of steel strand and open telephonelines. Made of malleable iron. Has shaft for placing on the endof an extension section handle. Hole in the shaft allows the lock-ing pin in the sleeve of the pole to fasten the tool to the exten-sion handle. Fits 1-1/4" shaft.

No. 6600 Series Extension HandleGENERAL MACHINE PRODUCTS

K

Ordering Information

Order Mfg.No. No.GMP 009296 06355

© 1996 TELEWIRE SUPPLY K134

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. DescriptionGMP 009299 66000 1-1/4’’ diameter by 6’ in length - 1 piece

GMP 009300 66001 1-3/4’’ diameter by 6’ in length - 1 piece

GMP 009302 66002 tapered from 1-1/4" to 1-3/4" - 1 piecediameter by 6’ in length

Page 136: TWS Sec_K

Measuring SticksHASTINGS

K

Tools & Safety EquipmentMeasuring Sticks

© 1996 TELEWIRE SUPPLYK135

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionLightweight, safe and compact. Ideal for taking fast and accu-rate vertical measurements of overhead lines, highway clear-ances, structural heights and checking sag. Eye level readingeliminates need for calculations. Extended height is shown attop of base section. Spring loaded pin lock at base of each sec-tion. Bronze hook on tip end. Will not chip or peel. Marked withfoot, inch and one-half inch measurements.

Ordering Information

Order Mfg.No. No. DescriptionHTG 006772 E1-125 25' height

HTG 006774 E1-130 30' height

HTG 006776 E1-135 35' height

HTG 006778 E1-140 40' height

Water repellent, vinyl snap top carrying case 20'-25' heavy duty, 20'-25'-30' standard lengths

HTG 006843 C-30

Water repellent, vinyl snap top carrying case 30' heavy duty, 35' standard length

HTG 006844 C-35

The illustrations above are examples only, consult theNational Electric Safety Code for complete clearance rules.

Page 137: TWS Sec_K

K

Tools & Safety EquipmentPulling Grips

"Haven" Steel GripsKLEIN Description

All parts are solid steel drop-forgings, heat treated.Instantaneous hold, yet a shake on tackle rope releases grip. Willnot slip due to serration in face of eccentric. Galvanized finish.

DescriptionWill work on figure 8 cable with .109 messenger. Lightweight,for working solid and stranded bare wire from .08" to .20".Single V-groove jaw. Maximum safe load is 1500 lbs.

Chicago GripsKLEIN

Ordering Information

Order Mfg.No. No. Weight Description

KLN 008943 1604-10 1 lb. min. cable size, 14 B&S .06" max. cable size, 2 B&S .25"; max. safe load, 2500 lbs.; up to 1/4" strand

KLN 008944 1604-20 2-1/2 lbs. min. cable size, 8 B&S .125" max. cable size, steel strand. 50"; max.safe load, 5000 lbs.; 1/4" or 5/16" strand

KLN 008945 1604-20L 2-1/2 lbs. same as 1604-20, with swing latch; 1/4" or 5/16" strand

© 1996 TELEWIRE SUPPLY K136

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. WeightKLN 008949 1613-30 1-1/2 lbs.

insidejawcontour

Chicago GripsKLEIN Description

Similar to Bell System Type B strand puller. Pulls 1/4" figure8 telephone cable. Serpentine grooves to grip insulation, pre-venting slippage or damage. Furnished with chain, toggle andshackle. Maximum Safe Load: 5000 lbs.

Ordering Information

Order Mfg.No. No. SizeKLN 008985 1659-5AT .20"-.37"

insidejawcontour

Page 138: TWS Sec_K

DescriptionFor A.S.C.R., Aluminum and Copper Stranded Cable. Round,smooth inside jaw contour grips with maximum contact, with lesspossibility of damaging conductor. Maximum safe load: 4500 lbs.

DescriptionFor Messenger and Guy Strand Heavy Cable, Etc. Will workon 3/16", 1/4", 5/16" strand. Double "V" grooves give 4 point con-tact, reducing chance of slipping and providing proper alignment.

K

Tools & Safety EquipmentPulling Grips

Chicago GripsKLEIN

Chicago GripsKLEIN

Chicago GripsKLEIN

DescriptionBell System type grips. Fitted with chain, toggle and shackle toprevent grip from falling in case of disengagement from cable.Maximum safe load: 8000 lbs.

© 1996 TELEWIRE SUPPLYK137

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. SizeKLN 008951 1613-40 .10"-.37"

insidejawcontour

Ordering Information

Order Mfg.No. No. SizeKLN 008970 1656-20 .20"-.40"

insidejawcontour

Ordering Information

Order Mfg.No. No. SizeKLN 075287 1684-5AT .218-.55"

insidejawcontour

Strand Sizes in Fractions Converted to Decimals

3/16" __________ .1875

1/4" ___________ .25

5/16 ___________ .3125

3/8" ___________ .375

7/16" __________ .4375

1/2" ___________ .5

Page 139: TWS Sec_K

Tools & Safety EquipmentPulling Grips

DescriptionUsed for bare or insulated conductors on normal overheadinstallations. With Rotating Forged eye.

O.D. Sizes for Commscope Trunk Cable

Light Duty Pulling GripsKELLEMS

Multiple Strength Pulling GripsKELLEMS

K

This chart will be helpful in choosing a pulling grip

Cable Size 500 540 625 715 750 860 875 1000 1125

Bare .500 .540 .625 .715 .750 .860 .875 1.00 1.125

Jacketed .560 .610 .685 .785 .820 .960 .945 1.08 1.225

Underground .570 N/A .695 N/A .830 N/A .955 1.09 N/A

Armored .715 .765 .835 .935 1.00 1.11 1.097 1.26 1.38

© 1996 TELEWIRE SUPPLY K138

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Cable Safe Work Breaking No. No. Din Load Strength

KLM 008999 033-02-016 .25-.49 1,360 lbs. 6,800 lbs.

KLM 009000 033-02-018 .50-.74 2,000 lbs. 10,000 lbs.

KLM 009001 033-02-020 .75-.99 2,880 lbs. 14,400 lbs.

KLM 009002 033-02-022 1.0-1.25 4,920 lbs. 24,600 lbs.

KLM 009003 033-02-024 1.25-1.49 6,120 lbs. 30,600 lbs.

Ordering Information

Order Mfg. Cable Safe Work Breaking No. No. Din Load Strength

KLM 009014 033-03-010 .50-.61 500 lbs. 2,800 lbs.

KLM 009015 033-03-011 .62-.74 500 lbs. 2,800 lbs.

DescriptionUsed for light pulls where heavy duty grip is not required. Thisis a quality single weave pulling grip. Swaged aluminum collar;tubular protection; varied mesh; endless weave, and flexiblepulling eye. Standard mesh: 20"-32".

Page 140: TWS Sec_K

DescriptionFlexible Eye Pulling Grips for fiber optic cable are made of highstrength galvanized steel strand. They feature a multi-wavemesh, with one-half the mesh length double weave, and thesecond half single weave. This special weave provides positiveholding power while allowing the grip to remain flexible with nodamage to the cable jacket. Added features include a steelnose cone which protects the cable and allows the grip to passeasily through conduit and enclosures. The flexible eye con-nects easily to a swivel or a pulling line. Six grip sizes are avail-able to accommodate all diameters of fiber optic cable.

Tools & Safety EquipmentPulling Grips

Junior Pulling GripsKELLEMS

DescriptionFor pulling multiple insulated wires through conduit.

Fiber Optic Pulling Grip - Flexible EyeKELLEMS

K

© 1996 TELEWIRE SUPPLYK139

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg. Cable Breaking No. No. Din StrengthKLM 009017 033-05-001 .25-.36 450 lbs.

KLM 009018 033-05-002 .37-.49 900 lbs.

KLM 009019 033-05-003 .50-.61 1,300 lbs.

KLM 009020 033-05-004 .62-.74 1,950 lbs.

KLM 009021 033-05-005 .75-.99 2,800 lbs.

Ordering Information

Order Mfg. Cable DiameterNo. No. RangeKLM 201922 033-29-1000 .10-.22

KLM 201923 033-29-1001 .21-.35

KLM 201924 033-29-1003 .32-.48

KLM 201925 033-29-1004 .42-.61

KLM 201926 033-29-1005 .53-.74

KLM 201927 033-29-1006 .64-.87

Break Away SwivelsCONDUX Description

Essential for fiber optic and coaxial cable pulling, these swivelshave a break load ranging from 150 - 1,800 pounds and aredesigned to separate at ± 10% of their rated break load. If theload rating is exceeded, the interior break pin fractures, theswivel separates, and the cable remains undamaged. Breakpin is easily replaceable.

Ordering Information

Order Mfg. BreakNo. No. Description LoadCDX 202092 08017200 5/8 swivel 600 lb.

CDX 202137 08017205 5/8 replacement pin 600 lb.

CDX 202093 08015000 7/8 swivel 600 lb.

CDX 202136 08015005 7/8 replacement pin 600 lb.

Page 141: TWS Sec_K

Tools & Safety EquipmentPulling Grips

DescriptionAluminum housing. 5-1/2' of lift. One ton hoist is proof-tested to3,000 lbs. and rated to lift loads up to and including 2,000 lbs.Two ton hoist is proof-tested to 6,000 lbs. and is rated to liftloads up to and including 4,000 lbs. Well balanced for easyhandling, fast-operating.

Break-Away SwivelGENERAL MACHINE PRODUCTS

Chain Ratchet HoistsCHANCE

K

© 1996 TELEWIRE SUPPLY K140

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionThese simple tools provide a safe, easy way to eliminate over-pulling, by putting an inexpensive fracture point between thepulling line and cable. The 7/8" size is ideal for small interductsand around tight bends.

If the pulling load reaches ± 5% of the break point, a tensionbolt joining the barrel eye and swivel separates, protecting thecable. You can then replace the bolt in seconds with an Allenwrench (included) and a standard screwdriver. Both bolt andswivel are color-coded for fast load identification.

Swivels feature steel thrust washers and self lubricating bush-ings to provide smooth rotation under load. This helps to keeptwisting forces from reaching the cable.

Ordering Information

Order Mfg. BreakNo. No. Point DescriptionGMP 123093 53702 600 lbs. break away swivel

GMP 123090 34341 600 lbs. replacement bolt-yellow

GMP 024786 25494 450 lbs. replacement bolt-orange

Ordering Information

Order Mfg.No. No. Weight DescriptionCHC 009044 3011S 14 lbs. 1-ton hoist

CHC 009069 4012 28.25 lbs. 2-ton hoist

Page 142: TWS Sec_K

DescriptionOperates as hoist, winch or puller; used in lifting, pulling and stretchingapplications; safety tested to 50 percent overload. Operates in any posi-tion; no ropes or chains to tangle.

High strength steel frame. Cast parts of heat-treated steel. Aircraft typeheat-treated bolts. Drop-forged steel safety latch hooks. Aluminum alloyratchet wheel.

Cable swaged to aircraft specifications. All steel parts plated. Automaticlet-down.

Tools & Safety EquipmentPulling Grips

Lever Hoists

Power-Pull Winch-Hoists

K

© 1996 TELEWIRE SUPPLYK141

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionCapacities 3/4 to 1-1/2 tons. Ratchet and pawl design with roller type chain.

Ratchet and pawl construction assures sure operation and freedom from maintenance. Bodyand handle made of malleable iron.

All multiple-chain hoists through 6 tons can be converted to the next smaller capacity for longerlift and faster operation.

Double pawls can be operated with half strokes of lever for use in close quarters. Note: hookswith latches are standard. Where clearance dimensions are critical, request certified print.

Ordering Information

Order Mfg. Betw. Min. Dist Approx. PullNo. No. Cap Full Required for

Tons Hooks Standard Load Lift WeightDNT 009036 AG 3/4 12-7/8" 56 lbs. 56-1/2" 14 lbs.

DNT 021279 ATG-1 1-1/2 14-7/8" 60 lbs. 57" 17 lbs.

Ordering Information

Order Mfg. Max Cable LeverageNo. No. Capacity Lift Diameter Ratio

MSD 009047 72S-6 1000 lbs. 6' 3/16 15:1

MSD 009051 144S-6 1000 lbs. 12' 3/16 15:1

MSD 009068 144SB-6 2000 lbs. 6 ' 3/16 30:1

Page 143: TWS Sec_K

K

Tools & Safety EquipmentPulling Grips

Block & TackleKLEIN

DescriptionFurnished complete with 25' of 3/8" manila rope. One endhas block with snap hook and detachable drop-forgedanchor hook; opposite end has block with eye and rope tie-off hook on other end.

Description• For Suspension Strand • Guy Strand • Static Wire

Ordering Information

Order Mfg.No. No. DescriptionKLN 008833 1802-30 with No. 267 and 268 blocks

KLN 008834 1802-30S with No. 259 detachable swivel hook

KLN 095495 1802-30S/R blocks have nose extended overkeeper, with detachable swivel hook

Ordering Information

Order Mfg.No. No. Description

REP 009093 9055 For 1/4" thru 3/8" Strandvise All Grades; for 5/16" thru 7/16" Strandvise UtilitiesGrade; .215-.270 and .270-.315 Universal

REP 009094 9062 For 1/2" Strandvise All Grades;

.325-.392 thru .455-.520 Universal

10-1/2"

1-1/2"

Strandvise Pulling HooksRELIABLE POWER

Innerduct Pulling EyesCONDUX

DescriptionClevis Head - Same tapered threads as the standard innerductpulling eye, these pulling eyes feature a slotted head with cle-vis pin to permit direct attachment to any multiple pulling har-ness leg ends.

Fixed Head - Tapered buttress threads thread into theinnerduct for maximum pulling strength. When properly sizedand installed, these eyes will not pull out of the innerduct untilthe pulling tensions have greatly exceeded the maximumpulling tensions recommended by the innerduct manufactur-ers, Condux has a full range of pulling eye sizes. Call yourTelewire sales representative for more options.

Ordering Information

Order Mfg. Nominal InnerductNo. No. Size ID Range

CDX 202138 08913341 1-1/4" 1.23" - 1.39" clevis head

CDX 202098 08913508 2" 1.96" - 2.09" clevis head

CDX 202139 08913325 1-1/4" 1.18" - 1.34" fixed head

CDX 202099 08913328 2" 1.98" - 2.06" fixed head

CDX 202100 08913350 (pulling eye installation tool. Fits 1/2"socket wrench)

Fixed Head Innerduct Pulling EyeClevis Head Innerduct Pulling

© 1996 TELEWIRE SUPPLY K142

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Page 144: TWS Sec_K

DescriptionDesigned to be used with Dillon tension and compression mea-surement equipment, the WI-120D features front panel config-uration, multiple load cell application, peak-hold, interfacecapability with computers, printers, chart recorders and otherdata collection devices.

DescriptionTensiometers monitor tension loads on wire, rope or cable.The RLT (running line tensiometer) is designed to beinstalled on a line that must move through the tensiometer.1,000 lb. capacity. 2mv/v full scale sensitivity.

K

Tools & Safety EquipmentFiber Optic Construction Tools

Dynamometers DILLON

Cable TensiometerDILLON

Digital Load IndicatorDILLON

Ordering Information

Order Mfg. Approx Weight w/No. No. Shackles & PinsSVC 141103 30007-0026 12 lbs.

SVC 148311 30006-0027 9 lbs.

© 1996 TELEWIRE SUPPLYK143

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No.SVC 141104 31991-1K

Ordering Information

Order Mfg.No. No.SVC 141105 WI-120D

Tension RecorderCHANCE Description

Provides permanent record of tension during pull. Disc-typerecorder. In line, mounts between drive-head and bull wheel.Includes five marking pen tips and 25 disc charts for rope.

Ordering Information

Order Mfg.No. No.CHC 141111 C417-6076

DescriptionSVC 141103 - 10"/254 mm diameter dial anti-parallaxdynamometer. 1,000 lb. capacity in 5 lb. gradations. 10 to 1 safe-ty factor. Accurate to ±1/2% of full range. Aluminum alloy case.

SVC 148311 - 5"/127 mm diameter dial anti-parallax dynamome-ter. 1,000 lb. capacity in 10 lb. gradations. 10 to 1 safety factor.Accurate to ±1/2% of full range. Aluminum alloy case.

Page 145: TWS Sec_K

Tools & Safety EquipmentFiber Optic Construction Tools

DescriptionSeries 90 Capstan hoist. Rated to 1,000 lbs. Electric drive at 115 volts AC. Lightweight.

Fiber Optic CapstansGMP

Capstan Hoist BracketCHANCE

range is factory-set and wire-locked at a predetermined pullwithin the range.The capstan's pull setting can be modified inthe field by using a dynamometer. When used with proper lineprotection, it helps maintain a constant pulling capacity, sub-stantially boosting the efficiency of hydraulic pullers.

This capstan consists of an aluminum alloy capstan drum mea-suring 27-1/2" outside diameter with a 5" wide working surface.The capstan drum is bolted to an inner hub and drive spindleby means of three 1/2-13 x 1-1/4" cap screws with 3/4" hexheads. Because of the combined weight of the drive sectionand the capstan drum assembled, it is recommended that twopeople mount the unit. This capstan is equipped with an inte-gral torque limiter between the driving spindle and the innerhub. The torque limiter limits the pulling tension to a calibratedmaximum, typically set at the factory at 600 pounds-force.

Capstan HoistCHANCE

DescriptionFor use with capstan hoist. Includes two chain clamps for pole mounting.

K

Ordering Information

Order Mfg.No. No. WeightGMP 144019 15472 106 lbs.

© 1996 TELEWIRE SUPPLY K144

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionThe capstans are specially designed to work with an existingwinch to provide faster cable pulling. It limits pulling torque dur-ing fiber optic cable placement. The torque limiter variable slip

Ordering Information

Order Mfg.No. No.CHC 141112 C308-1170

Ordering Information

Order Mfg.No. No.CHC 141113 C308-1335

Page 146: TWS Sec_K

K

Tools & Safety EquipmentFiber Optic Construction Tools

Fiber Optic Cable Puller

DescriptionThe Fiber Optic Cable Puller from Condux sets new standardsfor safe, accurate pulling of fiber optic cables. Only the Conduxpuller can offer load cell torque input for the most accurate ten-sion measuring available. Unlike most hydraulic measuringsystems, this system is not affected by changes in oil temper-ature, component age and power source. That means theCondux Fiber Optic Cable Puller does not need to be recali-brated under different weather conditions.

These pullers consist of a 30" (762 mm) diameter capstan,hydraulic motor, variable-speed foot control, manual flow con-trol valve for adjusting maximum speed and a manuallyadjustable pressure relief valve for adjusting the ultimate pulltension. A footage counter is also included.

The Condux Fiber Optic Cable Puller features an optional elec-tronic tension control system with adjustable digital load limitsand a load cell tension measuring device (patent pending). Theelectronic tension control system directly measures the rota-tional torque at the motor, thereby indicating actual cablepulling forces. The load limits are coupled to an audible alarmand automatic puller shut-off with load holding. The control boxis powered by a 12 volt DC input to run off a vehicle battery orthe supplied battery pack.

Also available is a 4" (102 mm) strip chart recorder incorporat-ed into the electron control box for a permanent record of thecable pull.

WARNING: The Fiber Optic Cable Puller is not to be used asa hoist or for lifting, supporting or transporting people or loads.

Components

Condux Fiber Optic pullers are multi-component products. Ordera puller to fit your requirements with combinations of these com-ponents (see ordering information). Components include:

• Hydraulic puller mounted on a standard 2-1/2"(64 mm) square tube

• 30" (762 mm) diameter capstan• Foot control/hydraulic control assembly• Electronic control box• Chart recorder• Battery pack for the tensiometer• Hoses and cords to connect the puller to the foot control

assembly and electronic control box

© 1996 TELEWIRE SUPPLYK145

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Specifications

12" (305mm) 30"(762mm) 50"(1270mm)Dia. Capstan Dia. Capstan Dia. Capstan

Pulling Force lbs. kN lbs. kN lbs. kN

Maximum 2000 8.9 1000 4.4 600 2.7

Continuous 2000 8.9 1000 4.4 600 2.7

Pulling Speed ft/min. m/min. ft/min. m/min. ft/min. m/min.

No load 93.9 28.6 240. 73.2 391.4 119.3

At max. Force 93.9 28.6 240. 73.2 391.4 119.3

Power Requirements

Pressure 2,000 to 2,500 psi (137 to 172 bar)

Flow 6 to 10 gpm (22.7 to 37.9 lpm)

Peak Power 8 HP (5.97 kw)

Page 147: TWS Sec_K

K

Tools & Safety EquipmentEquipment for Line Vehicles

Fiber Optic Cable PullerPackages 1,2 & 3

DescriptionThis portable power source is matched perfectly to the powerrequirements of the Condux Cable Glider HYD and the FiberOptic Cable Puller. Power source is a 16 HP (11.9 kW) Briggs& Stratton V-Twin Vanguard (gas or diesel) engine. Featureselectric start, large capacity hydraulic cooler, quick disconnects,low oil shut-off, and 16" (406 mm) diameter pneumatic tires.

Portable Hydraulic Power Pack

Ordering Information

Order Mfg.No. No. Description Contents

CDX 202107 08690000 Package One • Hydraulic puller mounted on a 2-1/2" (64mm) square tube

• 30" (762mm) diameter capstan• Foot control / hydraulic control

assembly

CDX 202108 08690025 Package Two • All items in Package One plus:• Electronic control box• Battery Pack

CDX 202090 08690050 Package Three • All items in Package One & Two plus:• Chart Recorder

© 1996 TELEWIRE SUPPLY K146

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. DescriptionCDX 202091 08675200 Hydraulic Power Pack, Gas

CDX 202106 08675250 Hydraulic Power Pack, Diesel

Specifications

Hydraulic System Open Center

Frame Type Two wheel mobile unit

Length 35.0" (889mm)

Width 29.0" (736mm)

Height 32.0" (812mm)

Weight (dry) 233 lbs. (105.6 kg)

Filtration 10 Micron Return Line Canister Type

Oil Cooler Air to Oil

Engine Briggs & Stratton V-Twin VanguardRated at 16 HP @ 3,600 RPM

Fuel 5.0 gallons / 18.9 liters

Hydraulic Oil (useable) 5.0 gallons / 18.9 liters

Hydraulic Rated Flow GPM @ PSI LPM @ BAR9.1 0 34.4 08.2 2,000 31.0 138

Hydraulic Relief Valve Pressure 2,150.0 PSI (148.3 BAR)

Page 148: TWS Sec_K

Tools & Safety EquipmentShovels

Quick DitcherJACKSON

Sharpshooter Drain SpadesUNION

Open Back Pattern ShovelsUNION

DescriptionBlade is 4-3/4" wide, 14" long, with forward turned step and 9"socket. Heat treated. Handle is 27" D- handle with steel top.

K

© 1996 TELEWIRE SUPPLYK147

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

DescriptionUse this tool to open the ground, to place drop wire 7" deep inshort run and in hard to get at places. Made of steel, with a footpad and tapered blade. This tool can also be used to shape atrench or hole after digging.

Ordering Information

Order Mfg.No. No. WeightJKS 069553 1502 18 lbs.

DescriptionBlade: Open back pattern with rolled step, forged from one-piece of 16 gauge steel. Sockets 9" square top. Heat treated,anti-rust finish. Size 2. Handle: Ash handles. Flamehard andwax finish.

Ordering Information

Order Mfg.No. No.UFK 008071 45-106

Ordering Information

Order Mfg.No. No.UFK 070238 47-107

DescriptionThis can help to dig hard ground and in close areas wheretrenching. Made of steel for added weight and durability.

Ordering Information

Order Mfg.No. No. WeightJKS 108235 1505 11 lbs.

Digging Bar 1505JACKSON

Page 149: TWS Sec_K

K

Tools & Safety EquipmentAnchor Rod Drivers

DescriptionThis two person machine is used to place screw anchors up to6" in diameter on 5-1/2" long rod. It can also be used to digholes with earth augers. This unit will save time and make hardjobs much easier. It comes with the 1509 Anchor Rod Adapter.

DescriptionOne of the most potentially dangerous parts of cable construc-tion is the placement of ground rods. With the Jackson groundrod driver, one person can do the job safely and quickly. Use p/nGRD-1 for ground rod diameters up to 5/8". The extra heavyweight and rubber jacketed handles on p/n GRD-3 make thistool extra effective in placing ground rods in hard sub-surfaces.

Ground Rod Drivers GRD -1, -3JACKSON

Anchor Rod Driver 1506JACKSON / STIHL

© 1996 TELEWIRE SUPPLY K148

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Ordering Information

Order Mfg.No. No. WeightJKS 081325 GRD-1 25 lbs.

JKS 099927 GRD-3 40 lbs.

Ordering Information

Order Mfg.No. No. WeightJKS 109361 1506 44 lbs.

JKS 114633 1059 Replacement adapter

Description120 Volt unit. @ 10 Amps, torque = 1,000 ft lbs. @ 20 Amps,torque = 1,500 ft. lbs. @ 23 Amps, torque = 1,800 ft. lbs. Portableanchor installer consists of: (1) electric drive head with 5¡/›” boltcircle drive flange and torque bar bracket; (1) round telescopictorque bar; (1) torque controller (limits maximum torque to 1,800ft. lbs.); (1) foot control.

No-Wrench Anchor Drive ToolCHANCE

Portable Electric Anchor InstallerCHANCE

DescriptionUse the E303-0255 no-wrench drive tool to install all sizes ofno-wrench anchors.

Ordering Information

Order Mfg.No. No.CHC C303-1060

Ordering Information

Order Mfg.No. No.CHC C303-0255

Page 150: TWS Sec_K

K

Tools & Safety EquipmentChemicals

© 1996 TELEWIRE SUPPLYK149

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

AdvantagesA versatile petroleum-based compound that forms a clear,thin film that lubricates and protects against corrosion

• Multi-purpose lubricant, penetrant and corrosion inhibitor• Displaces and seals out moisture• Penetrates through corrosion to loosen frozen parts• Lubricates without leaving a sticky residue• Cleans light soils and contaminants• MSDS Safety Data Sheet under the label

ApplicationsProcess Manufacturing:

• Heat treated parts• Machined surfaces• Finished welds• In-process aluminum extrusions

Machining:• Shim stock • Jigs• Chocks • Drill rod

Material Storage:• Tubing • Castings• Gears • Weld rod & wire

Maintenance:• Hoists • Frozen joints• Conveyors • Locks• Air actuated tools• Similar to LPS - 1

CRC 3-26®

Ordering Information

Order Mfg. Container UnitsNo. No. Size Per Case

CRI 158782 03160 16 oz. 12

"MSDS"Material Safety Data Sheetunder the Label of all CRC products

Putting the MSDS under the product label is a patented idea by CRC Products

Page 151: TWS Sec_K

Tools & Safety EquipmentChemicals

K

© 1996 TELEWIRE SUPPLY K150

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

Stor & Lube ®

Contact Cleaner 2000®

Applications• PC boards• Edge connectors• Contacts and relays• Tape heads• Metal switches• Scales• Sensors• Flux removal• Not for use on Noryl® and/or polycarbonate type plastics

AdvantagesA high purity HCFC-based precision cleaning solvent designedto meet today’s cleaning challenges.

• Fast cleaning action for removal of flux, light oils, & contaminants

• Evaporates rapidly and leaves no residue• No flash point, non-conductive, and non-corrosive• MSDS Sheet under the label

Advantages

Provides both superior lubrication and heavy-duty corrosion pro-tection for metal parts and assemblies that are stored indoors forup to two years. Promotes easy start-up of stored equipment.

• Long-lasting lubrication• Displaces moisture to prevent corrosion• Protects copper and brass• Protects equipment and parts in storage, shipment, and in process• High pressure lubricant that withstands up to 1,250 lbs. of

pressure in Falex test method• MSDS Sheet under the label

Applications• Chain drives • Cables• Overhead cranes & trolleys • Conveyor systems• Wire & rope • Gears• Lifts • Sensors• Exposed shafts • Dies• Jigs • Tools• Machinery • Piping• Bearings• Moving metal parts subject to constant wear• Metal parts in severe corrosive atmospheres• Similar to LPS - 3

Ordering Information

Order Mfg. Container UnitsNo. No. Size Per Case

CRI 158797 02140 16 oz. 12

Ordering Information

Order Mfg. Container UnitsNo. No. Size Per Case

CRI 158785 02061 16 oz. 12

ApplicationsHelps protect, lubricate and restore:

• Electrical connectors • Relays• Circuit breakers • Transformers• Switchgear • Motors• Generators • Controls• Instruments • Communication Assemblies• Electronics • Alarm Systems• Starters • Similar to LPS - 2

Advantages

Multi-purpose lubricant helps prevent electrical and electronicmalfunction caused by water penetration, humidity, condensa-tion, or corrosion.

• Cleans, lubricates, penetrates and loosens corrosion• Prevents corrosion by displacing moisture• Restores resistance values and helps stop current leakage• Helps restore water-damaged electrical equipment• Convenient 360° spray valve• Will not harm modern plastics, including polycarbonates,

ABS and Noryl®

• MSDS Sheet under the label

CRC 2-26®

Ordering Information

Order Mfg. Container UnitsNo. No. Size Per Case

CRI 158783 02005 16 oz. 12


Recommended