Date post: | 04-Apr-2015 |
Category: |
Documents |
Upload: | peterlow0218 |
View: | 446 times |
Download: | 1 times |
Information is Tyco Confidential & Proprietary - Do Not Reproduce or Distribute
Fiber OSP Products for Graybar
Presented by:
Craig RayApplications Engineering Manager
August 4, 2006
Greg Pierce – Product Manager(FOSC 450, AirFOSC, FibrBox, Fiber Drop Repair)
Amy Schwirian – Product Manager(FTERM)
David Braga – Product Manager(CSX-2, Splitters)
August 4, 20062
Telecom Outside Plant
• World’s largest supplier of Telecom Outside Plant products
• FOSC (Fiber Optic Splice Closures) and accessories
• FibrBox, Fiber Drop Repair, FTERM, TX & IS Shelves
• CSX-2 Splitter Cabinet, Splitters
August 4, 20063
FOSC (Fiber Optic Splice Closures)
Greg Pierce – Product Manager
Wide range of closures for most all Telecom Outside Plant needs:
• Hermetically sealed FOSC® Closures:
– FOSC 400 – Heat Shrink Sealing technology
– FOSC 450, 500, 600 – Gel Sealing Technology
• Free breathing FOSC Closures:
– Air FOSC (Gel sealing around cable entry)
• Fiber Drop Repair Splice Closure
• Full line of accessories
August 4, 20064
Full Range of Closure ProductsSingle and Mass Fiber Management
Cable Sealing TechnologyHeat Shrink Gel
Butt FOSC 400-Size ASize BSize D
FOSC 450Size A
Size BSSize BSize D
In-Line XAGA FOSCFITS FOSC
Fiber Drop Repair
FOSC 500Size AASize B
*FOSC 600Size CSize D
Air FOSCSize ASize B
Fiber Drop Repair* In-line or Butt configuration
August 4, 20065
Gel cable sealing technology
• Conforms to wide ranges of shapes and sizes of cable
• Flexible in wide temperature ranges
• Gel withstands harsh chemical environments
• Cold Sealed…no heat gun required
FOSC 450 Gel Sealed Closures
August 4, 20066
FOSC 450 Closure Features• Dome-ended, butt style closures
• Variety of sizes for wide range of applications
• Re-entry accomplished in 7 seconds with dome to base clamp.
• Cable sealing accomplished by easy to use, wrap-around gel seal
• Gel under compression accomplished by simply tightening the gel block tail
• Can be re-entered and re-used over and over
August 4, 20067
The FOSC 450 Family
• FOSC 450 D6 (576 splice capacity w/basket)
• FOSC 450 B6 (144 splice capacity w/basket)
• FOSC 450 BS (144 sp. cap. w/basket. Short length)
• FOSC 450 A4 (Up to 96 splice capacity)
All products use standard building block components and practices to minimize training and improve quality
Big
Small
FOSC 450 D6
FOSC 450 A4
August 4, 20068
FOSC 450 Multi-Drop Kits
• Multiple small or drop cable installations in a single port
• Fits all FOSC 450 Closures
• 2 Versions:- 3-Drop (Quick Install) Version
- 4-Drop (Gel Wrap) Version
August 4, 20069
FOSC 450D Split Base
• Provides upgrade or rehab capabilities to any existing closure when combined with standard 450 D closure
• Provides wraparound capabilities
• Available alone, or in a FOSC 450D closure kit
August 4, 200610
AIR FOSC Closure
Aerial, Free Breathing Splice Closure
• In-Line and Taut Sheath Capability
• 2 Sizes Available:
– AIR FOSC A30.5 inches long
– AIR FOSC B• 39 inches long• Taut sheath capability
August 4, 200611
AIR FOSC Closure
• Splice Capacity: 96 single splices or 288 mass fusion splices
• Slack Storage capacity: Up to 10 ft (120 inches) of loose buffer tube or ribbon
• Gel end pieces prevents water and dust ingress
• Removable outer body for better access
• Interior frame features:- Removable splice tray holder
- Powder coated frame
- 6 strength member retention claps –“bottle caps”
August 4, 200612
FIBRBox Fiber Pedestal Enclosure
• Rugged housing
• Grommeted/gasketed door and cable entry ports
• Up to 96 splices, 4 feeder cables, 16 drops
• Mounts in pedestals, on poles, or walls (additional mounting bracket available)
• Hinging, removable splice trays
• Removable cable entry plates for fast cable/drop installation
• Removable door with security screw
August 4, 200613
FIBRBox Mounting Options
Flush Mount
• Flush Mount
• Wall/Pole Mount Bracket
• Side Mount Bracket
Flush Mount
August 4, 200614
Fiber Drop Repair Closure
• Heat-shrink and cold-sealed versions available
• Taught sheath design
• Designed for single or ribbon splice – multiple loose fibers should be ribbonized
• Low cost
• Splice stand accessory available
August 4, 200615
FTerm UMT: Stubbed Terminal Applications
• Terminals can be located between the fiber distribution hub and the subscriber for a Plug-N-Play solution
– 4, 6, 8, and 12 port sizes available
– Factory Pre-stubbed – 50 ft to 200 ft standard length increments available
– Splice the stub cable to a main distribution cable
• Designed and tested for the Outside Plant environment using proven Tyco Electronics/ Raychem technology (Tested to Telcordia GR-771 and “PFOC”
Amy Schwirian – Product Manager
August 4, 200616
Product Dimensions
Ports Terminal Style Dimensions (LxWxH)4* Narrow, 2x2 9.4" x 3.4" x 2.8"
6* Narrow, 2x3 12" x 3.4" x 2.8"
8* Narrow, 2x4 14.6" x 3.4" x 2.8"
12 Wide, 4x3 12" x 6" x 3"
* Narrow designs compact enough to fit into a 4 inch duct
August 4, 200617
CSX-2 288 & 576
• Pivoting 36 Fiber Shelf
• Double Doors (<17”)
• Pad & Pole Mount Designs
• Front Access w/ Rear Cable Compartment Access
• Full Bend Radius Controls
• Upgradeable w/ Field Installed Shelves
• Field Replaceable Sides, Doors and Lid
David Braga – Product Manager
August 4, 200618
CSX-2 Functional Block Diagram
xxFeeder
Cable DistributionCable
1xn
CSX-2 Cabinet
SpliceTray
SpliceTray
InputShelf
SplitterModule
OutputShelf
x = Fusion Splice= Mated Connectors
Pigtail
Pigtail
Pigtail Storage
= Unmated Connector
August 4, 200619
CSX-2 Modular Pivoting Shelf• Accessibility of connectors both front and
rear allows easy cleaning of rear connectors
• 36 SC/APC connectors per distribution shelf
• Optional splice tray available in shelf for repair splicing
• Ribbon fanouts from shelf route to lower splice rays for factory or field stub cable splicing
• Radius control added for side exiting pigtails
• Extended base support bracket prevents pigtail “sag” from getting pinched in the shelf below and protects pigtails from front impact.
• Removable bulkhead panel
August 4, 200620
OCM5 Splitter Module & Pigtail Storage
• Module capacity for 1pc 2x32, 2pc 2x16, 4pc 2x8
• Fits all CSX-2 Cabinets
• 16 port connector retainer - connector is protected and “captured”
• Dust cap stays on the ferrule for endfaceprotection
• Mounted above shelves
• Minimal initial Routing/Plug-in
• Easy accessibility and routing of pigtails
• Storage area in cabinet for 4 to 8 splitters
August 4, 200621
CSX-2 288 Cabinet
August 4, 200622
CSX-2 144
• September ’06 Product Release
• Pivoting 36 Fiber Shelf
• 72 Fiber Shelf Assembly (2x36 fiber shelves) is Pre-Stubbed and Field Installable
• Gel Cable Seal
• Pad & Pole Mount Designs
• Total Front Access
• Simplified Pigtail Management
• 19” Internal Frame Structure
• Removable Outer Shell
• Side Mount Ground Bar / Toning Access
August 4, 200623
CSX-2 144 Key Cabinet Components
Splitter Module Mounting Area(5 Module Capacity)
36 Fiber Output Shelves (4x)
12 - 24 Fiber InputShelf (1x)
Cable Sealing Bracket(4 Cable Capacity)
Splitter Pigtail Parking Lots(64 Port Capacity)
Pad MountSkirt (10” height).
Pigtail Management/Routing Area
Ground Bar Access Panel – Side Mount
August 4, 200624
Configurations, Dimensions, Weights
Approximate Dimensions
H x W x D (in)
144 Pad/Pole 5 64 12 R or LT 2x72 R or LT 33.5 x 21.25 x 15 105288 Pad/Pole 10 128 24 R or LT 288 R or LT 49 x 23.5 x 15 145576 Pad 20 256 48 R or LT 2x288 R or LT 49 x 48 x 15 325
Notes: 1. Configuration offerings are subject to change.2. Dimensions and weights are estimated for some cabinet configurations. Weights do not include cable stubs or packaging.3. Stub cables may be Ribbon (R) or Loose Tube (LT) deigns.4. Pad mount configurations include a 9" skirt height.5. CXS-2 splitter modules are described in Tyco Electronics' OCM5 data sheet
Standard Distribution Cable
Stub
Weight (lbs) Color
Almond
Application
Splitter Module
Mounting Capacity
Splitter Port Storage Capacity
Standard Feeder Cable
Stub
Cabinet Size /CustomerCapacity
August 4, 200625
CSX-2 Requirements / Specifications
• CSX-2 Cabinet: RUS Bulletin 1753F-302 (PE-91)
• Splitter Modules: Tyco Electronics RUD 5330
• Connectors/Adapters: Telcordia GR-326, Issue 3
August 4, 200626
Splitter Products
Splitter Applications in FTTx
August 4, 200627
Splitters Types• Split Optical Power – Better Utilization of Equipment and Fiber in the PON
• Types: Fused Fiber (FBT) and Planar Circuit (PLC)
• Sizes: 1x2 thru 2x32
• FBT Features:– Low Loss– Good Uniformity– Best Price (1x2 – 1x8)– Built with Concatenated 1x2’s
• PLC Features:– Lower Loss– Improved Uniformity– Best Price (1x16 – 1x32)
FBT Splitters
PLC Splitters
August 4, 200628
Splitter Packaging
• Splitters Provided In …– FOSC Trays (A or D)– FIST Trays (SOSA)
• Connectorized Modules Also Available (CSX and CSX-2 Cabinets)
• FOSC and FIST Trays can be Applied to Closures, Shelves, Cabinets
August 4, 200629
Splitter (Rack Mounted Designs)
OCFPS Optical Component Front Patching Shelf
• Central Office / Headend Applications• LAN’s• Network Monitoring• 19” Rack Mount Ready• Connectorized FBT and PLC Splitter
Types • 1x2 through 2x32 Split Ratios• Low Loss Splitters Available• SC, SC/APC, LC, FC, FC/APC Connector
Types Available
OCM Optical Component Module
• Splitter Modules for LGX Chassis
August 4, 200630
NEXG Networks – 144 Splice/Patch
OSP 144fX
F-IS Splice Shelf144 fiber splice capacity
TX3 Patch Shelf (2x)72 fiber patch capacity ea.
Pigtails to Equipment
12, 12f IFC Cables SC/APC Connectors
Recommended Shelf Configurations: (see datasheets)F-IS3-IXNA-12LA-NNNNF-TX3-IBSA-CAB6-3012
Note: F-TX…“3012” is a custom part name for this application
Customer should confirm ordering information per datasheets
August 4, 200631
IS Shelves• Function
Splicing OSP Cable to Inter-Facility Cable (IFC)
• CapabilitiesFOSC 400 Fiber Management System, Snap-in Hinging Trays. Shelf fits 19” and 23” racks.
• SplicingOSP to IFC, OSP to IFC Pigtail, IFC to IFC Pigtails, OSP to OSP
• CapacityShelf -144 single fusion splicesTray - 12 single fusion splices or 6 mass
fusion splices
• DimensionsH x W x D: 5” x 17.5” x 11”
August 4, 200632
TX Shelves
• FunctionConnectorized Termination Point for Fiber Optic Cables
• CapabilitiesTray is field re-configurable for patching or splicing on either end of the tray. The TX tray is also reversible. Open access to both sides of removable adapters. Shelf fits into 19” and 23” racks.
• Shelf CapacityPatching - Up to 72 jumper-jumper
- Up to 6 IFC 12 Fiber Cables Splicing - Up to 72 single fusion splices to
pigtails (6 trays per shelf)
• DimensionsH x W x D: 1.8/3.3/5” x 17.5” x 11”
August 4, 200633
Technical Support ContactsWestern Regional Sales Manager
• Ted Dolmat (626) 297-7078
Customer Service Representative
• Lisa Russell (919) 557-2106
Product Managers:
• Greg Pierce – Closures (919) 557-8524
• Amy Schwirian – FTERM (919) 557-8779
• David Braga – CSX Cabinets (919) 557-8416
Applications Engineering Manager
• Craig Ray (919) 557-8679