Versions:
System:
NCS 125 M-HD
Mechanical-hydraulic power
transmission up to 40 kN.
NCA 125 M-HD/HD
Version for vertical use, direct
mounting on the machine table
Accurate position clamping with
a clamping slider against a fixed
jaw.
NCS 125 HD
hydraulic version via external hy-
draulic power unit up to 35 kN.
NCS-ZA 125 M-HD
with tie-rod system and mechani-
cal-hydraulic power transmission
up to 25 kN.
Type: Machine vice Viewon-line:
NCS
15
Impressive advantages:
Repeat accuracy ≤ 0.01 mm Fixed jaws secured on all levels (X,Y,Z) Vertical use directly on the machine table optionally as NCA Large clamping range due to stepped jaw attachments Basic equipment: 2 reversible screw-in jaws and 1 hand crank Laterally tiltable, with mounting holes for a groove of 63 mm
and 100 mm (for a bed length of 470 mm – otherwise optional)
NCS is our best-seller!Versatile and cost-efficient
CustomisableGroove and threadfor false jawsand grip bars
Stand-aloneFlexible - suitable for every ma-chine table, with clamping insert and tenon blocks (optional) ready to go
Optimum positioningTraverse groove for alignment
Quick pre-configuringShot pin for fast pre-positioning of different workpiece sizes
+49 (0)7183-8922 [email protected]
Suitableaccessoriesyou can findstarting from
page 96
Multi-clampingUsage of changeover sliders enable more workpieces
to be clamped. No tools required for assembly
Optional: Saves timeQuick retrofitting through
pull-down quick-change jaws (p. 128)
Optional:Angle drive
For operation from above, in confinedspaces and for long bottom parts
Spindle driveOptionally, mechanical-hydraulic version up to 40kN or purelymechanical clamping up to 10kN. Pure hydraulic clamping up to 35kN by replacing the clampingslider.
ON REQUEST:
Bed length up to1,200 mm
+49 (0)7183-8922 [email protected] 17
NCS
ESS
DSS
MFS
ZSS
UN
IVZ
AAc
cess
orie
s
NCS 125 M-HD Technical drawing
Manual or mechanical-hydraulic –clamping up to 1,200 mm of bed length
Technical specificationsOrder No. 09522 09523 09524 09525 09526 09527 09528 09529 Optionally
without jaws 09522000100
09523000100
09524000100
09525000100
09526000100
09527000100
09528000100
09529000100
Jaw width/Total width 125/127
Bed length D 470 534 598 662 726 790 854 918 max. 1,200
Overall length E 564 628 692 756 820 884 948 1012
d 115 167 199 231 263 295 327 359
X 300 400 500 500 500 500 500 500
Y 280 – 480 480 480 480 480 480
Z 150 200 250 250 250 250 250 250
Span C 0-239 0-303 0-367 0-431 0-495 0-559 0-623 0-687
Span R 131-445 131-509 131-573 131-637 131-701 131-765 131-829 131-893
Span S 63-377 63-441 63-505 63-569 63-633 63-697 63-761 63-825
Weight kg 37.6 41.7 45.1 48.5 51.9 55.3 58.7 62.1
Clamping force diagram
40
35
26
17
8.5
00 1 2 3 4 5 6 7 8
Clam
ping
forc
e (k
N)
Spindle revolutions(release occurs at 2000 N)
NC125 M-HD
NC125 M-HDwith angle drive
Suitableaccessoriesyou can findstarting from
page 96
20 H7
Z ±0,02 Y ±0,02
X ±0,02 D
16
147
,1
E
12 F7
82
h7
43
+0,0
1 1
25
100 d ±0,02
43
-0,0
1
15 -0,01 C
S
R
D
E
F
C
1 2 3 4
B
A
321 5
C
D
4 6 7 8
A
B
DIN6
Maßstab: 1:2
Material:
Gewicht:
09522 NCS 125-470 A3
1 von 1
Blatt
Verwendungsbereich
Zeichnungsnummer
Benennung
WerkstückkantenDIN 6784
Zust. Änderungstext Datum Name
Rohm./Halbzeug
Datum Name
ErstelltGepr.
Zul. Abw.DIN ISO 2768-mH
Ober�ächeDIN ISO
1302
Schutzvermerk nach DIN 34 beachten!
SW 17
+49 (0)7183-8922 [email protected]
Manual or mechanical-hydraulic –clamping up to 1,200 mm of bed length
NCS 125/990 M-HD as the double vice of special central jaws and the second clamping jaw slide
NCS
ESS
DSS
MFS
ZSS
UN
IVZ
AAc
cess
orie
s
NCS 125 HD
Hydraulic clamping –for your mass productionTechnical drawing
Technical specificationsOrder No. 09532 09533 09534 09535 09536 09537 09538 09539 Optionally
without jaws 09532000100
09533000100
09534000100
09535000100
09536000100
09537000100
09538000100
09539000100
Jaw width/Total width 125/127
Bed length D 470 534 598 662 726 790 854 918 max. 1,200
Overall length E 542 606 670 734 798 862 926 990
d 115 167 199 231 263 295 327 359
X 300 400 500 500 500 500 500 500
Y 280 – 480 480 480 480 480 480
Z 150 200 250 250 250 250 250 250
Span C 0-239 0-303 0-367 0-431 0-495 0-559 0-623 0-687
Span R 131-445 131-509 131-573 131-637 131-701 131-765 131-829 131-893
Span S 63-377 63-441 63-505 63-569 63-633 63-697 63-761 63-825
Weight kg 37.7 41.1 45.2 48.6 52 55.4 58.8 62.2
Clamping force diagram
36
32
27.5
21
17
13.5
8
5.5
0 70 100 150 200 240 310 350 380
Clam
ping
forc
e (k
N)
Working pressure (bar)
NC125 HD
Suitableaccessoriesyou can findstarting from
page 96
16 12
F7 20
H7
Z ±0,02 Y ±0,02
X ±0,02 D
E
147
,1
82
h7
43
+0,0
1 1
25
100 d ±0,02
43
-0,0
1
C
S
R
15 -0,01
beidseitig G1/4"
D
E
F
C
1 2 3 4
B
A
321 5
C
D
4 6 7 8
A
B
DIN6
Maßstab: 1:2
Material:
Gewicht:
9532A3
1 von 1
Blatt
Verwendungsbereich
Zeichnungsnummer
Benennung
WerkstückkantenDIN 6784
Zust. Änderungstext Datum Name
Rohm./Halbzeug
Datum Name
ErstelltGepr.
Zul. Abw.DIN ISO 2768-mH
Ober�ächeDIN ISO
1302
Schutzvermerk nach DIN 34 beachten!
SW 17
+49 (0)7183-8922 [email protected]
NCS 125/470 HD withworkpiece loadingvia robots
NCS
ESS
DSS
MFS
ZSS
UN
IVZ
AAc
cess
orie
s
NCS-ZA 125 M-HD
Tie rodThe tie rod ensures best repetition accuracy with optimum stability. Note: The NCS-ZAis not tiltable laterally.
Highest repeating accuracyand precision due to tie rod system
Impressive advantages:
At full tension, the fixed jaw of the clamping slider is only deflected in the μ range. This substantially prevents misalignment of the fixed jaw and thereby the work- piece.
The tie rod allows for use with zero-point clamping systems. It transmits the clamping force directly to the jaw, with almost no load on the bottom part. This ensures that precision components can be produced.
The use of pull-down quick-change jaws extends the range of applications of the vice. It is even possible to compensate for existing angular misalignment of the workpieces.
Suitableaccessoriesyou can findstarting from
page 96
+49 (0)7183-8922 [email protected]
Technical drawing
Mode of operation
Technical specificationsOrder No. 09522ZA 09523ZA 09524ZA 09525ZA 09526ZA
Jaw width/Total width 125/127
Bed length D 470 534 598 662 726
Overall length E 564 628 692 756 820
d 115 167 199 231 263
X 300 400 500 500 500
Y 280 – 480 480 480
Z 150 200 250 250 250
Span C 0-239 0-303 0-367 0-431 0-495
Span R 131-445 131-509 131-573 131-637 131-701
Span S 63-377 63-441 63-505 63-569 63-633
Weight kg 39.7 43.2 46.7 50.2 53.7
Clamping force diagram
30
25
20
15
10
5
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5
Spindle revolutions(release occurs at 2000 N)
Clam
ping
forc
e (k
N)
Tie rod released
Tie rod clamped
20 H7
Z ±0,02 Y ±0,02
X ±0,02 D
16
147
,1
E
12 F7
82
h7
43
+0,0
1 1
25
100 d ±0,02
43
-0,0
1
15 -0,01 C
S
R
D
E
F
C
1 2 3 4
B
A
321 5
C
D
4 6 7 8
A
B
DIN6
Maßstab: 1:2
Material:
Gewicht:
09522 NCS 125-470 A3
1 von 1
Blatt
Verwendungsbereich
Zeichnungsnummer
Benennung
WerkstückkantenDIN 6784
Zust. Änderungstext Datum Name
Rohm./Halbzeug
Datum Name
ErstelltGepr.
Zul. Abw.DIN ISO 2768-mH
Ober�ächeDIN ISO
1302
Schutzvermerk nach DIN 34 beachten!
SW 17
+49 (0)7183-8922 [email protected] 23
NCS
ESS
DSS
MFS
ZSS
UN
IVZ
AAc
cess
orie
s