1
P G DRAIN LS EF CF 7A 2A 5A 8A 6A 3A 4A SAE 20 SAE 6 SAE 6 SAE 6 SAE 20 SAE 20 Without CF Bleed With CF Bleed P G DRAIN LS EF CF 7A 2A 5A 8A 6A 3A 4A SAE 20 SAE 6 SAE 6 SAE 6 SAE 20 SAE 20 P1 P2 G DRAIN LS EF1 EF2 100 PSI CF CODE SIZE CODE THREAD CODE Level CODE Version CODE TYPE CODE TYPE CODE TYPE CODE TYPE D #8 U UNC X Rev - X X E 75 PSI L STANDARD SCREW F 0.281 F 100 PSI F #12 A Rev A G 0.563 H #16 H 0.688 I #20 I 0.85 Maj Rev Level Min Rev Level - Modulating Spring Rate (2A) Needle Control (3A) Needle Range (3A) (Determined by Valve Size) Check Crack PSI (4A) Port Size (Determined by Flow) Mounting Type PART NUMBER SELECTION VP- HV CODE TYPE CODE TYPE Select CODE TYPE Select CODE TYPE Select CODE TYPE A Standard HVD A ALUMINUM (No finish) 1 Single Pump O15 15 GPM S SAE STD C Standard HVD w ext orf cav D DUCTILE IRON (standard finish) 2 Dual Pump O35 35 GPM O65 65 GPM 130 130 GPM Valve Pack Hammer Valve Flow Capacity Port Type PRODUCT TYPE Circuit (Determined by valve size) - MATERIAL FUNCTION CODE TYPE Select CODE TYPE Select CODE MATERIAL Select CODE VOLTAGE Select CODE OPTION A 500 TO 3000 PSI 0 Std W/ No CF Bleed N BUNA 14 14 Vdc D DIN W/ S18211TC4*1 C 500 TO 6000 PSI 1 Std W/ Manual CF Bleed V VITON 28 28 Vdc W 500 TO 4500 PSI Orifice Options (6A) SEAL MATERIAL CONTROL SOLENOID CONNECTOR OPTIONS Adjustment Range (5A) 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 A A B B C C D D DWG NO DATE JUNE 2015 TITLE SINGLE OR DUAL INPUT HAMMER VALVES WITH PRESSURE AND FLOW CONTROL HAMMER VALVE SERIES INCH 3RD ANGLE PROJECTION PROPRIETARY NOTICE THIS DRAWING DESCRIBES A PROPRIETARY PRODUCT OF LYNCH FLUID CONTROLS INC. WHICH MAY NOT BE REPRODUCED IN WHOLE OR IN PART NOR GIVEN TO A THIRD PARTY WITHOUT WRITTEN PERMISSION FROM LYNCH FLUID CONTROLS INC. DATA UNIT: Lynch Fluid Controls Inc. MODEL CODE VP-HV_-_ PROPRIETARY NOTICE This Drawing describes a Proprietary Product of Lynch Fluid Controls Inc. which may not be reproduced in whole or in part nor given to a third party without written permission from Lynch Fluid Controls Inc. L y n c h Fluid Controls Inc. 1799 Argentia Rd. Mississauga, Ontario Canada L5N 3A2 Phone : 1 905 363 2400 Phone : 1 888 626 4365 Fax : 1 905 363 1192 www.lynch.ca TYPICAL SCHEMATICS FOR SINGLE PUMP INPUT UNITS TYPICAL SCHEMATICS FOR DUAL PUMP INPUT UNITS (Shown w/o CF Bleed) DUAL PUMP MAX FLOW: 2015 = 2x 15 GPM INLET (P1 & P2), ~ 21 GPM OUT (CF) 2035 = 2x 35 GPM INLET (P1 & P2), ~ 49 GPM OUT (CF) 2065 = 2x 65 GPM INLET (P1 & P2), ~ 91 GPM OUT (CF) 2130 = 2x 130 GPM INLET (P1 & P2), ~ 182 GPM OUT (CF) TYPICAL PART NUMBER: VPHVA-D1065SHUAX-ELHFC0N28D DI Body, Single Pump, 65 GPM Input, SAE #16 Ports, UNC mounting, 75 PSI Spring, Screw Adjustment, 0.688" Max Orifice, 100 PSI Check, 500 to 6000 PSI, No CF Bleed, Buna Seals, 28 VDC Coil w/ DIN Connector SINGLE PUMP MAX FLOW: 1015 = 15 GPM INLET (P1), ~ 11 GPM OUT (CF) 1035 = 35 GPM INLET (P1), ~ 25 GPM OUT (CF) 1065 = 65 GPM INLET (P1), ~ 46 GPM OUT (CF) 1130 = 130 GPM INLET (P1), ~ 91 GPM OUT (CF)
