Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com2 4/07
*Also acceptable for use with 250# PSI polybutylene tubing.Insert stiffeners are required on all flexible plastic connections. See page 5.
EPDM gasket
tubing
AWWA straight threads
“T” nut
Stainless steel bev-eled gripper
recommended torque Chart for t Series Compression NutsTighten to the following minimum torques:
3/4" ............ 50 ft-lbs1" ............... 55 ft-lbs1 1/4" ......... 65 ft-lbs1 1/2" ......... 85 ft-lbs2" ............... 100 ft-lbs
AWWA straight threads
Flare nut
Copper Flare
Coppertubing
Bull nose endA. Remove the flare nut from the valve or fitting and slip it onto the copper tubing.
B. Flare the end of the copper tubing making sure the O.D. of the flare extends out to the threads in the flare nut, and is free of nicks and chips..
C. Screw the flare nut with tubing back onto the matching bull nose end of the valve or fitting and securely wrench tighten.
D. The flared portion of the copper tubing acts as a water-tight gasket and also is locked between the nut and coupling giving high pull-out resistance.
n T, and TA Compression
n 6130 Compression Coupling Converts Flare End to Compression AssemblyThe 6130 Compression Coupling converts any 3/4" or 1" flared joint into a tube size compression joint. For copper 6130CC or CTS polyethylene 6130CE.
A. Remove the flare nut from the valve or fitting and replace with the 6130 Coupling.B. Squarely cut the end of the copper or polyethylene tubing and insert it into the 6130 Coupling until the tubing bottoms out.*C. Tighten the 6130 Coupling onto the valve or fitting fingertight, then wrench tighten 2-3 more complete turns.DO NOt OVErtIGHtEN.
6130 body
AWWA straight threads
tubing
Stainless steel beveled gripper
EPDM gasket
Plastic spacerBull nose end
A. Insert tubing through the “T” compression nut and into the ma-chined socket of the valve or fitting.*B. Tighten the “T” compresion nut securely onto the valve or fitting, using the information from the recommended torque chart. This will: 1. Provide a water-tight seal by compressing both edges of the EPDM gasket around the tubing and; 2. Compress the stainless steel beveled gripper providing high pull-out resistance.NOtE: “T” Compression and Mac-Pak -22 nuts have the same threads and are interchangeable.
Copper tube, CtS PE (“t”) is stabbed thru nut to stab depth. the “t” nut is tightened to the required torque, which compresses the Buna-N or EPDM gasket and stainless steel beveled gripper, which creates a water-tight seal and pull-out strength.
“TA” Anode Compression Assembly
Copper tube is stabbed thru nut to stab depth. The “TA” nut is tightened to the required torque, which compresses the EPDM gasket and stainless steel beveled gripper, which cre-ates a water-tight seal and pull-out strength. A copper wire that leads to a zinc anode is locked into the compression nut via the stainless steel screw.
Stainless steel beveled gripper“T” nut
EPDM gasket
AWWA straight threads
Stab depth
tubing
Stainless steel screw
Anode nut
NOtE: Materials meet or exceed A.W.W.A. Standard C-800.
n Flare
For the electrical anode nut feature add “A” to the Model No.: 4701T = 4701tA
tubing
EPDM gasket AWWA straight threads
Stab depth
4700A
4700tA
Underground Water Service Fittings & Couplings
3A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com
4/07
*Also acceptable for use with 250# PSI polybutylene tubing.Insert stiffeners are required on all flexible plastic connections. See page 5.
n Mac-Pak Compression - 22, -33, -44, -55, -66, -67 and -68 Compression
AWWA straight threads
Mac-Pak nut with split clamp
Stainless steel screw
EPDM gasketAnti-friction ring
tubing
A. Insert tubing or plastic pipe through the nut into the machined socket in the valve or fitting.*
B. Wrench tighten the Mac-Pak nut securely onto the valve or fitting compressing the EPDM seal around the pipe or tubing, creating a water-tight seal.
C. Secure the split clamp onto the pipe or tubing by tightening the stainless steel bolt on the side of the clamp. Machined grooves in the split clamp provide additional gripping and electrical continuity.
D. Mac-Pak couplings are coded as follows: -22 SERIES - Tube size copper or P.E.* -- CtS -33 SERIES - Pipe size P.E.* PEP -44 SERIES - P.V.C. -- PVC -55 SERIES - Steel pipe -- IP
-66 SERIES - Strong lead pipe -- S -67 SERIES - Extra strong lead pipe -- XS -68 SERIES - Extra, extra strong lead pipe -- XXS
n McQuik Compression - Q, QA and -3Q Series
Q, QA or -3Q Series Nut
Stainless beveled gripper
EPDM gasket
Conductor Spring for electrical continuity
tubing
A. Stab tube* through the Q, QA or -3Q Series nut and into the socket of the valve or fitting until it bottoms out (three part unions may or may not have an internal stop).B. Tighten the McQuik Q, QA or -3Q Series nut to the stop. The end face of the nut is to contact the stop face of the body. This will: 1. Provide a water-tight seal by compressing both edges of the EPDM gasket around the tubing and; 2. Compress the stainless steel beveled gripper providing high pull-out resistance.
Copper tube CtS PE (Q), QA or PEP (-3Q) is stabbed through the nut to stab depth. the Q, QA or -3Q nut is tightened to the stop/shoulder on the body, which compresses the EPDM gasket and stainless steel beveled gripper, which creates a water-tight seal and pull-out strength. the electrical conductor spring makes positive contact between the copper tubing and the brass nut/fitting. When using with CtS PE (Q) QA or PEP (-3Q), the electrical conductor spring becomes purposeless.
Stainless steel beveled gripperQ, QA or
-3Q nutEPDM gasket
AWWA straight threads
Stab depth
tubing
Electrical conductor spring
Shoulder/stop
Copper tube or CtS PE (“-22”), PEP (“-33”), PVC (-44), IP (-55), strong lead (-66), extra strong lead (-67) or double extra strong lead (-68) is stabbed thru nut to stab depth. the nut is tightened to the required torque (see recommended torque chart for Mac-Pak compression), which compresses the EPDM gasket, which creates a water-tight seal. the stainless steel screw is tightened to the required torque (see chart), for pull-out strength.
Tighten to tthe following minimum torques:“-22”, “-33”, “-44”, “-55” CompressionFor nut: 1/2" ......... 20 ft-lbs 1" .............. 30 ft-lbs 1 1/2" ......... 40 ft-lbs(ft-lbs) 3/4" ......... 25 ft-lbs 1 1/4" ........ 35 ft-lbs 2" ............... 45 ft-lbs
For clamp 1/2" ... 70-80 in-lbs 1" ...... 90-100 in-lbs 1 1/2" 160-180 in-lbsside screw: 3/4" ... 80-90 in-lbs 1 1/4" 120-140 in-lbs 2" ..... 200-220 in-lbs(in-lbs)
Lead Mac-Pak Comp. “-66”, “-67”, “-68” CompressionFor nut: 1/2" ......... 25 ft-lbs 1" .............. 40 ft-lbs 1 1/2" ......... 50 ft-lbs(ft-lbs) 5/8" ......... 30 ft-lbs 1 1/4" ........ 45 ft-lbs 2" ............... 55 ft-lbs 3/4" ......... 35 ft-lbs
For clamp 1/2" ... 70-80 in-lbs 1" ...... 90-100 in-lbs 1 1/2" 160-180 in-lbsside screw: 5/8" ... 75-85 in-lbs 1 1/4" 120-140 in-lbs 2" ..... 160-180 in-lbs(in-lbs) 3/4" ... 80-90 in-lbs
Iron pipe (-55) is stabbed thru nut to stab depth. the nut is tightened to the required torque, which compresses the EPDM gasket, which creates a water-tight seal. the stainless steel screw or screws are tightened to the required torque, for pull-out strength.
Stainless steel screw
Anti-friction ringEPDM gasket
Stab depth
AWWA straight threads
Machined grooves
tubing
NOtE: Materials meet or exceed A.W.W.A. Standard C-800.
Stainless steel screw
Any Q Series connection can be changed to a C903 Connection. Replace the “Q” in the model number with a “K.” 3/4" or 1" only.
NEW!
Q, QA or -3Q
-22, -33, -44, -66, -67, or -68 -55
Anti-friction ring
EPDM gasket Stab depth
AWWA straight threads
iron pipe
recommended torque Chart for Mac-Pak Compression Nuts
Electrical Continuity
4700QA
Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com4 4/07
A •
Nee
d in
sert
not a
vaila
ble
from
A.Y
. McD
onal
d M
fg. C
o.B
• N
o fit
ting
from
A.Y
. McD
onal
d M
fg. C
o. a
vaila
ble.
C •
T an
d Q
not
ava
ilabl
e fo
r 1/2
" siz
e.D
• -In
sert
stiff
eren
not
requ
ired
E • -
3Q o
nly
avai
labl
e in
3/4
" and
1" s
izes
.
A •
Nee
d in
sert
not a
vaila
ble
from
A.Y
. McD
onal
d M
fg. C
o.B
• N
o fit
ting
from
A.Y
. McD
onal
d M
fg. C
o. a
vaila
ble.
C •
T an
d Q
not
ava
ilabl
e fo
r 1/2
" siz
e.D
• -In
sert
stiff
eren
not
requ
ired
E • -
3Q o
nly
avai
labl
e in
3/4
" and
1" s
izes
.()
• Max
imum
pip
e O
.D. t
hat w
ill w
ork
with
A.Y
. McD
onal
d fit
tings
.
n T
ypes
of P
ipe/
Tub
ing
for
use
wit
h A
.Y. M
cDon
ald
Fit
ting
s (O
utsi
de D
iam
eter
s lis
ted)
*Inse
rt S
tiffe
ners
requ
ired
on a
ll fle
xibl
e pl
astic
con
nect
ions
Sha
ded
area
s in
dica
te w
here
lead
pip
e m
ay h
ave
to b
e sh
aved
to fi
t com
pres
sion
end
sho
wn.
LEA
D P
IPEu
POLY
BUTY
LENE
PO
LYET
HYLE
NE
PE
X TU
BING
PO
LYBU
TYLE
NE
ASTM
D26
62 S
IDR
7
AS
TM D
3035
TYPE
K o
r L
POLY
ETHY
LENE
AS
TM F
876
ASTM
D26
66 S
DR 9
o
r PO
LYET
HYLE
NE
SDR
9
DO
UBLE
NO
MIN
AL
COPP
ER
ASTM
D27
37 S
DR 9
SD
R 9
TUBE
SIZ
E AS
TM D
2239
SID
R 7
PVC
STEE
L
OD C
ONTR
OLLE
D ST
RONG
EX
TRA
STRO
NG
EXTR
A ST
RONG
SI
ZE
TUBE
TU
BE S
IZE
CSA
B137
.5
CLAS
S 25
0 PI
PE S
IZE
ASTM
D17
85
PIP
E PI
PE S
IZE
S or
A
XS o
r AA
XXS
or A
AA
1/
2"
.622
.6
21
.621
.6
25
.79
.836
.8
36
.7
83
.861
.9
97
.6
28
.629
.6
29
.633
.8
5 .8
44
.844
.813
.8
91
1.02
7
5/
8"
1.
004
1.06
7 1.
122
1.
034
1.09
7 1.
152
3/
4"
.872
.8
71
.871
.8
75
1.04
5 1.
046
1.04
6 1.
046
1.14
1 1.
197
1.32
1
.8
78
.879
.8
79
.883
1.
110
(1.08
9)
1.05
4 1.
054
1.05
4 1.
171
1.22
7 1.
351
1"
1.
121
1.12
0 1.
120
1.12
5 1.
329
1.31
0 1.
310
1.31
0 1.
413
1.47
7 1.
581
1.12
9 1.
130
1.13
0 1.
135
1.39
9 (1
.384)
1.
320
1.32
0 1.
320
1.44
3 1.
507
1.61
1
1 1
/4"
1.37
1 1.
370
1.37
0 1.
375
1.75
4 1.
655
1.65
5 1.
655
1.65
5 1.
750
1.87
4
1.
379
1.38
0 1.
380
1.38
5 1.
832
(1.80
4)
1.66
5 1.
665
1.66
5 1.
685
1.78
0 1.
904
1 1
/2"
1.62
1 1.
619
1.61
9 1.
625
2.05
0 1.
894
1.89
4 1.
894
1.96
9 2.
061
2.25
7
1.
630
1.63
1 1.
631
1.63
7 2.
141
(2.10
9)
1.90
6 1.
906
1.90
6 1.
999
2.09
1 2.
287
2"
2.
120
2.11
9 2.
119
2.12
5 2.
637
2.36
9 2.
369
2.36
9 2.
488
2.73
6 2.
993
2.13
0 2.
131
2.13
1 2.
137
2.74
2 (2
.709)
2.
381
2.38
1 2.
381
2.51
8 2.
766
3.02
3
Type
of
A
.Y.
-22,
Q o
r T
-22*
, Q* o
r T*
-22*
, Q* o
r T*
-22*
, Q* o
r T*
-33*
or -
3Q*
-44
-55
-44*
-6
6 -6
7 -6
8 F
ittin
gC
CC
ED
D
AA
BB
B
1 1/
4" -4
4
1 1/
2" -4
4
2" -4
4
2" -2
2
1 1/
2" -4
4 B
A CD
DD
D
Underground Water Service Fittings & Couplings
5A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com
4/07
n Insert Stiffeners - Insert Stiffeners required on all flexible plastic connections
n Installation Information
Sizes: 3/4", 1", 1 1/4", 1 1/2", 2"Sizes: 3/4", 1"•Also acceptable for use with 250 PSI
polybutylene tubing. ASTM D2666, SDR 9, CTS.
Sizes: 3/4", 1", 1 1/4", 1 1/2", 2"
6131T • PLAStICFor copper tube
size polyethyleneAStM D2737 SDr 9 - CtS
6136 • StAINLESS StEELFor ID Controlled PEP
AStM D2239 SIDr 7
6133T • StAINLESS StEELFor copper tube
size polyethyleneAStM D2737 SDr 9 - CtS
6137 • StAINLESS StEELFor OD controlled
PEP SDr9AStM D3035
Sizes: 3/4", 1", 1 1/4", 1 1/2", 2"
NEW!
Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com6 4/07
RW=Reduced Weight *Insert stiffeners are required on all flexible plastic connections. See page 5.
55 Steel Pipe Comp. Gasket and Gripper Gasket and Gripper Gasket and Gripper Gasket and GripperSize Nut Assembly (Gasket Assembly Only Assembly for Strong Lead Assembly for XStrong Lead Assembly for XXStrong Lead and Anti-Friction ring) 55 IP Series 66 S Lead Series 67 XS Lead Series 68 XXS Lead Series1/2" ● ●
5/8" ● ● ●
3/4" ● ● ● ● ●
1" ● ● ● ● ●
11⁄4" ●
11⁄2" ● ● ●
2" ● ● ●
4700-55 4700-55GA 4700-66GA 4700-67GA 4700-68GA
22 CtS Comp. Gasket and 33 PEP Comp. Gasket and 44 PVC Comp. Gasket andSize Nut Assembly (Gasket Anti-Friction ring Only Nut Assembly (Gasket Anti-Friction ring Only Nut Assembly (Gasket Anti-Friction ring Only and Anti-Friction ring) 22 CtS Series and Anti-Friction ring) 33 PEP Series and Anti-Friction ring) 44 PVC Series1/2" ● ●
3/4" ● ● ● ● ● ●
1" ● ● ● ● ● ●
11⁄4" ● ● ● ● ● ●
11⁄4" rW ● ●
11⁄2" ● ● ● ● ● ●
11⁄2" rW ● ● ● ●
2" ● ● ● ● ● ●
2" rW ● ●
n Flare and Compression Nut Assemblies
4700-22* 4700-22GA 4700-33* 4700-33GA 4700-44 4700-44GA
Copper Flare Nut Copper Flare Nut t CtS Comp. tA CtS Comp. Gasket & Gripper 3Q PEP Comp. Gasket & Gripper Only with Anode Nut Assembly Anode Nut Assembly Assembly Only Nut Assembly Assembly OnlySize Connection (Gasket & Gripper) (Gasket & Gripper) t CtS Series (Gasket & Gripper) 3Q PEP Series 1/2" ●
3/4" ● ● ● ● ● ● ●
1" ● ● ● ● ● ● ●
11⁄4" ● ● ●
11⁄2" ● ● ●
11⁄2" rW ● ●
2" ● ● ●
2" rW ● ●
4700 4700A 4700T* 4700TA* 4700TGA 4700-3Q* 4700-3QGA
Q CtS Comp. QA CtS Comp. Gasket and Gripper Clamp Screw-Small Clamp Screw-Large K C903 Comp. K C903 GripSize Nut Assembly Anode Nut Assembly Assembly Only For Mac-Pak For Mac-Pak Nut, ring, & Seal ring Only (Gasket & Gripper) (Gasket & Gripper) Q CtS Series Nuts Nuts Assembly 1/2"
5/8"
3/4" ● ● ● ● ●
1" ● ● ● ● ●
11⁄4" ● ● ●
11⁄4" rW
11⁄2" ● ● ●
11⁄2" rW
2" ● ● ●
2" rW
4700Q* 4700QA 4700QGA 4700CSS 4700CSL 4700K 4700KGR
Fits thesesizes
Fits thesesizes
NEW!
NEW!
Underground Water Service Fittings & Couplings
7A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com
4/07
4753 4753T*
4753-3Q*
SIZES AVAILABLE
4753-33* 4753-554753-44
4753Q* 4753-22*Size NUt MNPt FLArE x MNPt t CtS Comp x MNPt Q CtS Comp x MNPt 22 CtS Comp x MNPt1/2" 1/2" 1/2" ● ●
1/2" x 3/4" 1/2" 3/4" ● ●
3/4" 3/4" 3/4" ● ● ● ●
3/4" x 1/2" 3/4" 1/2" ● ● ● ● 3/4" x 1" 3/4" 1" ● ● ● ●
1" 1" 1" ● ● ● ●
1" x 3/4" 1" 3/4" ● ● ● ●
11⁄4" 11⁄4" 11⁄4" ● ● ● ●
11⁄4" x 3/4" 11⁄4" 3/4" ● ● ●
11⁄4" x 1" 11⁄4" 1" ● ● ●
11⁄4" x 11⁄2" 11⁄4" 11⁄2" ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ● ●
11⁄2" x 1" 11⁄2" 1" ● ● ●
11⁄2" x 11⁄4" 11⁄2" 11⁄4" ● ● ●
2" 2" 2" ● ● ● ●
2" x 11⁄2" 2" 11⁄2" ● ●
n Straight Couplings - One End Male National Pipe Thread
SIZES AVAILABLESize NUt MNPt 3Q PEP Comp x MNPt 33 PEP Comp x MNPt 44 PVC Comp. x MNPt 55 IP Comp. x MNPt3/4" 3/4" 3/4" ● ● ● ●
3/4" x 1" 3/4" 1" ● ● ● ●
1" 1" 1" ● ● ● ●
1" x 3/4" 1" 3/4" ● ● ● ●
1" x 11⁄2" 1" 11⁄2" ● ● ● ●
11⁄4" 11⁄4" 11⁄4" ● ●
11⁄4" x 1" 11⁄4" 1" ● ●
11⁄4" x 11⁄2" 11⁄4" 11⁄2" ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ●
11⁄2" x 1" 11⁄2" 1" ●
11⁄2" x 11⁄4" 11⁄2" 11⁄4" ●
2" 2" 2" ● ● ●
2" x 1" 2" 1" ● ● ●
Shown here is our basic line of service fittings. Other combinations not shown in this catalog may be available. Contact us for more information
*Insert stiffeners are required on all flexible plastic connections. See page 5.
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLYAnode/Thaw/Tracer nut available for 3/4" & 1" Flare & "T" Series and all sizes of "Q" Series.
u
uSee pages 18 & 19 for Flare conversion adapters
Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com8 4/07
n Straight Couplings - One End Female National Pipe Thread
4754 4754T*
4754-3Q*
SIZES AVAILABLE
4754-33* 4754-554754-44
4754Q* 4754-22*Size NUt FNPt FLArE x FNPt t CtS Comp x FNPt Q CtS Comp x FNPt 22 CtS Comp x FNPt1/2" 1/2" 1/2" ● ●
3/4" 3/4" 3/4" ● ● ● ●
3/4" x 1/2" 3/4" 1/2" ● ● ●
3/4" x 1" 3/4" 1" ● ● ● ●
1" 1" 1" ● ● ● ●
1" x 3/4" 1" 3/4" ● ● ● ●
1 x 11⁄4" 1" 11⁄4" ● ● ● ●
11⁄4" 11⁄4" 11⁄4" ● ● ● ●
11⁄4" x 3/4" 11⁄4" 3/4" ● ● ●
11⁄4" x 1" 11⁄4" 1" ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ● ●
11⁄2" x 1" 11⁄2" 1" ● ● ●
11⁄2" x 11⁄4" 11⁄2" 11⁄4" ● ● ●
2" 2" 2" ● ● ● ●
2" x 11⁄2" 2" 11⁄2" ● ●
SIZES AVAILABLESize NUt FNPt 3Q PEP Comp x FNPt 33 PEP Comp. x FNPt 44 PVC Comp. x FNPt 55 IP Comp. x FNPt1/2" x 1" 1/2" 1" ●
3/4" 3/4" 3/4" ● ● ● ●
3/4" x 1/2" 3/4" 1/2" 3/4" x 1" 3/4" 1" ● ● ● ●
1" 1" 1" ● ● ● ●
1" x 3/4" 1" 3/4" ● ● ● ●
1" x 11⁄4" 1" 11⁄4" ● ● ●
11⁄4" 11⁄4" 11⁄4" ●
11⁄4" x 11⁄2" 11⁄4" 11⁄2" ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ●
11⁄2" x 3/4" 11⁄2" 3/4" ●
11⁄2" x 11⁄4" 11⁄2" 11⁄4" ● ●
2" 2" 2" ● ● ●
2" x 3/4" 2" 3/4" ● ●
2" x 1 2" 1 ● ●
Shown here is our basic line of service fittings. Other combinations not shown in this catalog may be available. Contact us for more information
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLY
*Insert stiffeners are required on all flexible plastic connections. See page 5.
u
uSee pages 18 & 19 for Flare conversion adapters
Underground Water Service Fittings & Couplings
9A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com
4/07
n Straight Couplings
*Insert stiffeners are required on all flexible plastic connections. See page 5.
4758 4758T*
4758-3Q*
SIZES AVAILABLE
4758-33* 4758-554758-44
4758Q* 4758-22*Size NUt NUt FLArE x FLArE t CtS Comp x Q CtS Comp x 22 CtS Comp x t CtS Comp Q CtS Comp 22 CtS Comp1/2" 1/2" 1/2" ● ●
1/2" x 3/4" 1/2" 3/4" ● ●
3/4" 3/4" 3/4" ● ● ● ●
3/4" x 1" 3/4" 1" ● ● ● ●
3/4" x 11⁄4" 3/4" 11⁄4" ● ● ●
1" 1" 1" ● ● ● ●
1" x 11⁄4" 1" 11⁄4" ● ● ●
1" x 11⁄2" 1" 11⁄2" ● ● ●
11⁄4" 11⁄4" 11⁄4" ● ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ● ●
11⁄2" x 2" 11⁄2" 2" ● ●
2" 2" 2" ● ● ● ●
21⁄2" 21⁄2" 21⁄2" ●
SIZES AVAILABLESize NUt NUt 3Q PEP Comp x 33 PEP Comp. x 44 Comp. PVC x 55 IP Comp. x 3Q PEP Comp 33 PEP Comp. 44 Comp. PVC 55 IP Comp.1/2" 1/2" 1/2" ●
3/4" 3/4" 3/4" ● ● ● ●
3/4" x 1" 3/4" 1" ● ● ● ●
3/4" x 2" 3/4" 2" ● ● ●
1" 1" 1" ● ● ● ●
11⁄4" 11⁄4" 11⁄4" ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ●
2" 2" 2" ● ● ●
Shown here is our basic line of service fittings. Other combinations not shown in this catalog may be available. Contact us for more information
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLYAnode/Thaw/Tracer nut available for 3/4" & 1" Flare & "T" Series and all sizes of "Q" Series.
u
uSee pages 18 & 19 for Flare conversion adapters
4758C T* 4758CQ* 4758C-3Q*4758C-22*SIZES AVAILABLESize NUt NUt FLArE x FLArE x FLArE x FLArE x t CtS Comp Q CtS Comp 22 CtS Comp. 3Q PEP Comp3/4" 3/4" 3/4" ● ● ●
1" 1" 1" ● ● ●
1" x 3/4" 1" 3/4" ●
u
4758C -33* 4758C -554758C -44SIZES AVAILABLESize NUt NUt FLArE x FLArE x FLArE x 33 PEP Comp 44 PVC Comp. IP Comp3/4" 3/4" 3/4" ● ● ●
1" 1" 1" ● ● ●
1" x 3/4" 1" 3/4" ● ● ●
1" x 2" 1" 2" ● ● ●
u u u
Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com10 4/07
4758T*-33*4758T*-22*SIZES AVAILABLESize NUt NUt t CtS Comp x Q CtS Comp x t CtS Comp x 22 CtS Comp 22 CtS Comp 33 PEP Comp3/4" 3/4" 3/4" ●
3/4" x 1/2" 3/4" 1/2" ● ●
1" 1" 1" ● ●
1" x 3/4" 1" 3/4" ●
1" x 2" 1" 2" ●
2" 2" 2" ● ●
2" x 11⁄2" 2" 11⁄2" ●
n Straight Couplings
SIZES AVAILABLESize NUt NUt Q CtS Comp x 22 CtS Comp x Q CtS Comp x t CtS Comp x 33 PEP Comp 33 PEP Comp 3Q PEP Comp 44 PVC Comp3/4" 3/4" 3/4" ● ● ● ●
3/4" x 1" 3/4" 1" ● ● ●
1" 1" 1" ● ● ● ●
1" x 3/4" 1" 3/4" ● ● ●
1" x 11⁄4" 1" 11⁄4" ● 1" x 2" 1" 2" ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ●
11⁄2" x 11⁄4" 11⁄2" 11⁄4" ●
2 2 2 ● ● ●
Size NUt NUt Q CtS Comp x 22 CtS Comp x t CtS Comp x Q CtS Comp x 44 PVC Comp 44 PVC Comp 55 IP Comp 55 IP Comp1/2" 1/2" 1/2" ●
3/4" 3/4" 3/4" ● ● ● ●
3/4" x 1" 3/4" 1" ● ● ● ●
1" 1" 1" ● ● ● ●
1" x 3/4" 1" 3/4" ● ● ●
1" x 11⁄4" 1" 11⁄4" ●
1" x 2" 1" 2" ● ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ●
2" 2" 2" ● ● ● ●
*Insert stiffeners are required on all flexible plastic connections. See page 5.
4758T*-44
4758T*-554758-22*-44
4758-22*-33*
Shown here is our basic line of service fittings. Other combinations not shown in this catalog may be available. Contact us for more information
4758Q*-33*
4758Q*-55
4758Q*-3Q*
4758Q*-22*
4758Q*-44
uSee pages 18 & 19 for Flare conversion adapters
SIZES AVAILABLE
Underground Water Service Fittings & Couplings
11A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com
4/07
SIZES AVAILABLE 4758-33*-44 4758-44-554758-22*-55 4758-33*-55
4759T* 4759Q* 4759-22*SIZES AVAILABLE
n Straight Couplings
*Insert stiffeners are required on all flexible plastic connections. See page 5.
3-Part Unions with Internal Pipe Stop
Size NUt NUt t CtS Comp x Q CtS Comp x 22 CtS Comp x t CtS Comp Q CtS Comp 22 CtS Comp1/2" 1/2" 1/2" ●
3/4" 3/4" 3/4" ● ● ●
1" 1" 1" ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ●
2" 2" 2" ● ● ●
4759-33* 4759-44 4759-55SIZES AVAILABLESize NUt NUt 3Q PEP Comp x 33 PEP Comp x 44 PVC Comp x 55 IP Comp x 3Q PEP Comp 33 PEP Comp 44 PVC Comp 55 IP Comp3/4" 3/4" 3/4" ● ● ● ●
4759-3Q*
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLYAnode/Thaw/Tracer nut available for 3/4" & 1" Flare & "T" Series and all sizes of "Q" Series.
Shown here is our basic line of service fittings. Other combinations not shown in this catalog may be available. Contact us for more information
Size NUt NUt 22 CtS Comp x 33 PEP Comp x 33 PEP Comp x 44 PVC Comp x 55 IP Comp 44 PVC Comp 55 IP Comp 55 IP Comp3/4" 3/4" 3/4" ● ● ● ●
3/4" x 1" 3/4" 1" ● ● ● ●
3/4" x 2" 3/4" 2" ● ● ●
1" 1" 1" ● ● ● ●
1" x 3/4" 1" 3/4" ● ● ● ●
1" x 2" 1" 2" ●
11⁄2" 11⁄2" 11⁄2" ●
2" 2" 2" ●
SIZES AVAILABLE 4755DB 4755DBT*
Size NUt FFLr FLArE x FFLr t CtS Comp x FFLr 22 CtS Comp x FFLr Q CtS Comp x FFLr 3/4" 3/4" 3/4" ● ● ● ●
1" 1" 1" ● ● ● ●
11⁄2" 11⁄2" 2" ● ● ●
2" 2" 2" ● ● ●
4755DB-22* 4755DBQ*u
4758DB-22*-55
uSee pages 18 & 19 for Flare conversion adapters
Di-Electric Unions
Size NUt FNPt 22 CtS Comp x 22 CtS Comp Q CtS Comp x Q CtS Comp 22 CtS Comp x 55 IP Comp 3/4" 3/4" 3/4" ● ●
1" 1" 1" ● ● ●
1" x 3/4" 1" 3/4" ●
11⁄2" 11⁄2" 2" ● ●
2" 2" 2" ● ●
4758DB-22* 4758DBQ*
Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com12 4/07
n Tees
A
B KEY tO SIZES A B 3/4" x 1"
4760 4760T*SIZES AVAILABLE
4760-33* 4760-554760-44
4760Q*
SIZES AVAILABLESize BOtH SIDE 33 PEP Comp x 44 PVC Comp x MNPt x MNPt 55 IP Comp x FNPt x FNPt ENDS OUtLEt 33 PEP Comp x 44 PVC Comp x x MNPt 55 IP Comp x x FNPt rUN 33 PEP Comp 44 PVC Comp 55 IP Comp3/4" 3/4" 3/4" ● ● ● ● ●
3/4" x 1" x 9" 3/4" 1" ● 9" end to end
1" 1" 1" ● ● ● ● ●
1" x 3/4" 1" 3/4"
1" x 11⁄4" 1" 11⁄4" 1" x 11⁄2" 1" 11⁄2" 11⁄4" 11⁄4" 11⁄4" ●
11⁄2" 11⁄2" 11⁄2" ● ● ● ●
2" 2" 2" ● ● ● ●
A
Size BOtH SIDE FLArE x FLArE t CtS Comp x Q CtS Comp x 22 CtS Comp x 3Q PEP Comp x ENDS OUtLEt x FLArE t CtS Comp x Q CtS Comp x 22 CtS Comp x 3Q PEP Comp x rUN t CtS Comp Q CtS Comp 22 CtS Comp 3Q PEP Comp1/2" 1/2" 1/2" ●
3/4" 3/4" 3/4" ● ● ● ● ●
3/4" x 1" 3/4" 1" ● ● ● ●
1" 1" 1" ● ● ● ● ●
1" x 3/4" 1" 3/4" ● ● ● ●
1" x 11⁄4" 1" 11⁄4" ● ● ● ●
1" x 11⁄2" 1" 11⁄2" ● ● ●
11⁄4" 11⁄4" 11⁄4" ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ● ●
2" 2" 2" ● ● ● ●
Size BOtH SIDE FLArE x FLArE x 22 CtS Comp x 22 CtS Comp x 22 CtS Comp x ENDS OUtLEt FLArE Assembly 22 CtS Comp x 22 CtS Comp x 22 CtS Comp x rUN Pressure tested 33 PEP Comp 44 PVC Comp 55 IP Comp1" 1" 1" ● ● ●
2" x 1" 2" 1" ●
*Insert stiffeners are required on all flexible plastic connections. See page 5.
4760-22*-554760-22*-444760-22*-33*
4760-22* 4760-3Q*
4760P
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLY
NEW! NEW!
u
uSee pages 18 & 19 for Flare conversion adapters
4760F
SIZES AVAILABLE 4760A
Underground Water Service Fittings & Couplings
13A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com
4/07
n Tees
A
B KEY tO SIZES A B 3/4" x 1"
4762 4762T*SIZES AVAILABLE 4762Q* 4762-22*
A
Size BOtH SIDE FLArE x t CtS Comp x Q CtS Comp x 22 CtS Comp x ENDS OUtLEt FLArE x MNPt t CtS Comp x Q CtS Comp x 22 CtS Comp x rUN MNPt MNPt MNPt3/4" 3/4" 3/4" ● ● ● ●
3/4" x 1" 3/4" 1" ● ● ● ●
1" 1" 1" ● ● ● ●
4763 4763T*SIZES AVAILABLE 4763Q* 4763-22*Size BOtH SIDE MNPt x MNPt x MNPt x MNPt x MNPt x MNPt x MNPt x MNPt x ENDS OUtLEt FLArE t CtS Comp Q CtS Comp 22 CtS Comp rUN 3/4" 3/4" 3/4" ●
3/4" x 1" 3/4" 1" ● ● ● ●
3/4" x 1" x 9" 3/4" 1" ● 9" end to end ● 9" end to end ● 9" end to end ● 9" end to end
1" 1" 1" ● ● ● ●
1" x 11⁄4" 1" 11⁄4" ● ● ● ●
1" x 11⁄2" 1" 11⁄2" ● ● ●
4764T* 4764Q*SIZES AVAILABLE 4764-22*Size BOtH SIDE t CtS Comp x Q CtS Comp x 22 CtS Comp x ENDS OUtLEt t CtS Comp x Q CtS Comp x 22 CtS Comp x rUN FNPt FNPt FNPt 3/4" 3/4" 3/4" ● ● ●
3/4" x 1" 3/4" 1" ● ● ●
1" 1" 1" ● ● ●
11⁄2" x 3/4" 11⁄2" 3/4" ● ● ●
11⁄2" x 1" 11⁄2" 1" ● ● ●
2" x 3/4" 2" 3/4" ● ● ●
2" x 1" 2" 1" ● ● ●
*Insert stiffeners are required on all flexible plastic connections. See page 5.
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLY
Shown here is our basic line of service fittings. Other combinations not shown in this catalog may be available. Contact us for more information
u
u
uSee pages 18 & 19 for Flare conversion adapters
Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com14 4/07
4779M 4779MT*SIZES AVAILABLE 4779MQ*Size NUt MNPt FLArE x MNPt t CtS Comp x Q CtS Comp x 22 CtS Comp x MNPt MNPt MNPt3/4" 3/4" 3/4" ● ● ● ●
1" 1" 1" ● ● ● ●
1" x 3/4" 1" 3/4" ● ● ● ●
11⁄4" x 1" 11⁄4" 1" ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ● ●
2" 2" 2" ● ● ● ●
n Elbows • 1/4 Bend
SIZES AVAILABLESize NUt MNPt 3Q PEP Comp x 33 PEP Comp x 44 PVC Comp x 55 IP Comp x MNPt MNPt MNPt MNPt3/4" 3/4" 3/4" ● ● ● ●
1" 1" 1" ● ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ●
2" 2" 2" ● ● ●
n Elbows • 1/8 Bend
Size NUt FNPt FLArE x t CtS Comp x 22 CtS Comp x FNPt FNPt FNPt 3/4" 3/4" 3/4" ●
3/4" x 1" 3/4" 1" ●
1" 1" 1" ● ● ●
1" x 11⁄4" 1" 11⁄4" ●
4747 4747T*SIZES AVAILABLE 4747-22*
*Insert stiffeners are required on all flexible plastic connections. See page 5.
4779M-22*
4779M-33* 4779M-554779M-44
Shown here is our basic line of service fittings. Other combinations not shown in this catalog may be available. Contact us for more information
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLY
4779M-3Q*
u
u
uSee pages 18 & 19 for Flare conversion adapters
Underground Water Service Fittings & Couplings
15A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com
4/07
n Elbows • 1/4 Bend
4779 4779T*SIZES AVAILABLE 4779Q*Size NUt FNPt FLArE x t CtS Comp x Q CtS Comp x FNPt FNPt FNPt 3/4" 3/4" 3/4" ● ● ●
3/4" x 1" 3/4" 1" ● ● ●
3/4" x 11⁄4" 3/4" 1 1⁄4" ● ●
1" 1" 1" ● ● ●
1" x 11⁄4" 1" 11⁄4" ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ●
2" 2" 2" ● ● ●
Size NUt FNPt 22 CtS Comp x 44 PVC Comp x 55 IP Comp x FNPt FNPt FNPt 3/4" 3/4" 3/4" ●
3/4" x 1" 3/4" 1" ●
3/4" x 11⁄4" 3/4" 11⁄4" ●
1" 1" 1" ●
1" x 11⁄4" 1" 11⁄4" ●
11⁄2" 11⁄2" 11⁄2" ● ●
2" 2" 2" ● ● ●
4779-22* 4779-44SIZES AVAILABLE 4779-55
4761 4761T*SIZES AVAILABLE 4761-22*4761Q*Size NUt NUt FLArE x FLArE t CtS Comp x Q CtS Comp x 22 CtS Comp x t CtS Comp Q CtS Comp 22 CtS Comp3/4" 3/4" 3/4" ● ● ● ●
1" 1" 1" ● ● ● ●
11⁄4" 11⁄4" 11⁄4" ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ● ●
2" 2" 2" ● ● ● ●
4761-3Q* 4761-33* 4761-554761-44SIZES AVAILABLE
Size NUt NUt 3Q PEP Comp x 33 PEP Comp x 44 PVC Comp x 55 IP Comp x 44 PVC Comp x 3Q PEP Comp 33 PEP Comp 44 PVC Comp 55 IP Comp 55 IP Comp3/4" 3/4" 3/4" ● ● ● ●
1" 1" 1" ● ● ● ●
11⁄4" 11⁄4" 11⁄4" ●
11⁄2" 11⁄2" 11⁄2" ● ● ●
2" 2" 2" ● ● ● ●
*Insert stiffeners are required on all flexible plastic connections. See page 5.
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLY
4761-44-55
u
u
uSee pages 18 & 19 for Flare conversion adapters
Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com16 4/07
n Mac-Pak Lead Compression
4753-66 4753-67SIZES AVAILABLE 4753-68Size NUt MNPt 66 Strong Lead Comp. x 67 X Strong Lead Comp. x 68 XX Strong Lead Comp. x MNPt MNPt MNPt 1/2" x 3/4" 1/2" 3/4" ● ●
5/8" x 3/4" 5/8" 3/4" ● ● ●
3/4" 3/4" 3/4" ● ● ●
1" 1" 1" ● ● ●
11⁄4" 11⁄4" 11⁄4" ●
11⁄4" x 1" 11⁄4" 1" ●
11⁄2" 11⁄2" 11⁄2" ●
2" 2" 2" ●
4754-66 4754-67SIZES AVAILABLE 4754-68Size NUt FNPt 66 Strong Lead Comp. x 67 X Strong Lead Comp. x 68 XX Strong Lead Comp. x FNPt FNPt FNPt 1/2" x 3/4" 1/2" 3/4" ●
5/8" x 3/4" 5/8" 3/4" ● ● ●
5/8" x 1" 5/8" 1" ●
3/4" 3/4" 3/4" ● ● ●
4758-66 4758-67SIZES AVAILABLE 4758-68Size NUt NUt 66 Strong Lead Comp. x 67 X Strong Lead Comp. x 68 XX Strong Lead Comp. x 66 Strong Lead Comp. 67 X Strong Lead Comp. 68 XX Strong Lead Comp.1/2" 1/2" 1/2" ●
5/8" 5/8" 5/8" ● ●
3/4" 3/4" 3/4" ● ● ●
1" 1" 1" ● ●
11⁄4" 11⁄4" 11⁄4" ●
4758C -66 4758C -67SIZES AVAILABLE 4758C -68Size NUt NUt FLArE x FLArE x FLArE x 66 Strong Lead Comp. 67 X Strong Lead Comp. 68 XX Strong Lead Comp.3/4" 3/4" 3/4" ● ● ●
3/4" x 1/2" 3/4" 1/2" ● ●
3/4" x 5/8" 3/4" 5/8" ● ● ●
1" 1" 1" ● ● ●
1" x 1/2" 1" 1/2" ●
1" x 5/8" 1" 5/8" ● ● ●
1" x 3/4" 1" 3/4" ● ● ●
u
uSee pages 18 & 19 for Flare conversion adapters
u u
Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com18 4/07
n Couplings for Use with Copper Flare Outlets
4755 4755T* 4755-22*SIZES AVAILABLE
4755-33* 4755-554755-44
4755Q*Size NUt FFLr FLArE x FFLR t CtS Comp x FFLR Q CtS Comp x FFLR 22 CtS Comp x FFLR1/2" x 3/4" 1/2" 3/4" ● ●
3/4" 3/4" 3/4" ● ● ●
3/4" x 1/2" 3/4" 1/2" ● ● ● ●
3/4" x 1" 3/4" 1" ● ● ● ●
1" 1" 1" ● ● ●
1" x 3/4" 1" 3/4" ● ● ● ●
1 x 11⁄4" 1" 11⁄4" ● ● ●
1 x 11⁄2" 1" 11⁄2" ● ● ●
1 x 2" 1" 2" ● ● ●
11⁄4" x 1" 11⁄4" 1" ● ● ● ●
11⁄4" x 11⁄2" 11⁄4" 11⁄2" ● ● ●
11⁄4" x 2" 11⁄4" 2" ● ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ●
11⁄2" x 2" 11⁄2" 2" ● ● ● ●
2" 2" 2" ● ● ●
SIZES AVAILABLE
Size NUt FFLr 3Q PEP Comp x 33 PEP Comp x 44 PVC Comp x 55 IP Comp x FNPt x MNPt x FFLR FFLR FFLR FFLR FFLR FFLR1/2" 1/2" 1/2" ●
3/4" 3/4" 3/4" ● ● ● ● ● ●
3/4" x 1/2" 3/4" 1/2" ●
1" 1" 1" ● ● ● ● ● ●
1" x 3/4" 1" 3/4" ●
1 x 11⁄4" 1" 11⁄4" ●
1 x 11⁄2" 1" 11⁄2" ●
1 x 2" 1" 2" ● ●
11⁄4" x 1" 11⁄4" 1" ●
11⁄4" x 11⁄2" 11⁄4" 11⁄2" ●
11⁄4" x 2" 11⁄4" 2" ●
11⁄2" 11⁄2" 11⁄2" ● ●
11⁄2" x 2" 11⁄2" 2" ●
2" 2" 2" ● ●
2" x 11⁄2" 2" 11⁄2" ●
4755F 4755M
NOtE: 4755G Copper Gasket included with all 4755 connections.
*Insert stiffeners are required on all flexible plastic connections. See page 5.
4755-3Q*
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLY
6130CC 6130CEFemale Copper Flare to CtS
Compression CouplingFemale Copper Flare to CtS
Compression Coupling6125 4755GSIZES AVAILABLE
COPPEr GASKEt FFLr x Copper FFLr x CtS PE CompSize FFLr END SOLID COPPEr DISC for 4755 Connections tube Comp Includes Stiffener1/2" 1/2" 1/2" ●
3/4" 3/4" 3/4" ● ● ● ●
1" 1" 1" ● ● ● ●
11⁄4" ● 11⁄2" ● 2" ●
uSee pages 18 & 19 for Flare conversion adapters
u
Underground Water Service Fittings & Couplings
19A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com
4/07
n Couplings for Use with Copper Flare Outlets
4750 4750T*SIZES AVAILABLE 4750-22*Size FFLr NUt FIXED FFLr x FLArE FIXED FFLr x t CtS Comp FIXED FFLr x 22 CtS Comp3/4" 3/4" 3/4" ● ● ●
1" 1" 1" ● ● ●
4750S 4750ST* 4750S-444750S-22*SIZES AVAILABLE
Size SWIVEL NUt Swivel FFLr x Swivel FFLr x Swivel FFLr x Swivel FFLr x Swivel FFLr x FFLr FLArE Q CtS Comp t CtS Comp 22 CtS Comp 44 PVC Comp3/4" 3/4" 3/4" ● ● ● ●
1" 1" 1" ● ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ● ● ●2" 2" 2" ● ● ● ● ●
SIZES AVAILABLE
NOtE: 4755G Copper Gasket included with all connections on this page.
*Insert stiffeners are required on all flexible plastic connections. See page 5.
4776 4776T* 4776-22*4776Q*SIZES AVAILABLESize FFLr NUt Fixed FFLr x Fixed FFLr x Fixed FFLr x Fixed FFLr x
FLArE t CtS Comp Q CtS Comp 22 CtS Comp3/4" 3/4" 3/4" ● ● ● ●
1" 1" 1" ● ● ● ●
11⁄4" 11⁄4" 11⁄4" ● ● ●
Size SWIVEL NUt Swivel FFLr x Swivel FFLr x Swivel FFLr x Swivel FFLr x FFLr FLArE t CtS Comp Q CtS Comp 22 CtS Comp3/4" 3/4" 3/4" ● ● ● ●
1" 1" 1" ● ● ● ●
11⁄4" x 1" 1" 11⁄4" ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ● ●
2" 2" 2" ● ● ● ●
4776S 4776ST* 4776S-22*4776SQ*
4750SQ*
Shown here is our basic line of service fittings. Other combinations not shown in this catalog may be available. Contact us for more information
SIZES AVAILABLESize SWIVEL NUt Swivel FFLr x Swivel FFLr x Swivel FFLr x Swivel FFLr x FFLr 3Q PEP Comp 33 PEP Comp 44 PVC Comp 55 IP Comp3/4" 3/4" 3/4"
1" 1" 1" ● ● ● ●
11⁄2" 11⁄2" 11⁄2" ●
2" 2" 2" ● ●
4776S-3Q* 4776S-33* 4776S-44 4776S-55*
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLYAnode/Thaw/Tracer nut available for 3/4" & 1" Flare & "T" Series and all sizes of "Q" Series.
u
u
u
u
uSee pages 18 & 19 for Flare conversion adapters
Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com20 4/07
n Y-Branches
0 8 Y 2 C C 1 x 3/4
B
SizeSingle opening end x Multiple opening ends
Model No. 08Y2CC 1 x 3/4 means:
All Y-Branches Number of branches2 = Two branches3 = Three branches4 = Four branchesS = Service fittings (all 2 branch)
Type of connection-Single opening endC = Copper flareK = C903 CompressionL = Copper flare, less nutM = MNPTQ = McQuik CompressionT = T CompressionZ = 3Q Compression2 = 22 Compression3 = 33 Compression4 = 44 Compression5 = 55 Compression
Type of connection-Multiple opening ends(Same codes as single opening end)
A B
A
B
08YSTT*SIZES AVAILABLE
08YSMC 08YSMT*SIZES AVAILABLE 08YSM2*Size Single Multiple MNPt x MNPt x MNPt x MNPt x
End Ends FLArE t CtS Comp 22 CtS Comp Q CtS Comp1" x 3/4" 1" 3/4" ● ● ● ●
08YS22* 08YS33* 08YS5508YS44SIZES AVAILABLESize Single Multiple 22 CtS Comp x 33 PEP Comp x 44 PVC Comp x 55 IP Comp x End Ends 22 CtS Comp 33 PEP Comp 44 PVC Comp 55 IP Comp1" x 3/4" 1" 3/4" ● ● ● ●
11⁄4" x 1" 11⁄4" 1" ●
11⁄2" x 1" 11⁄2" 1" ●
2" x 1" 2" 1" ●
*Insert stiffeners are required on all flexible plastic connections. See page 5.
08YSQQ*Size Single Multiple FLArE x Q CtS Comp x C903 Comp x t CtS Comp x 3Q PEP Comp x End Ends FLArE Q CtS Comp C903 Comp t CtS Comp 3Q PEP Comp1" x 3/4" 1" 3/4" ● ● ● ● ●
11⁄4" x 1" 11⁄4" 1" ● ●
11⁄2" x 1" 11⁄2" 1" ● ●
2" x 1" 2" 1" ● ●
08YSZZ*08YSCC
08YSMQ*
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLY
Shown here is our basic line of service fittings. Other combinations not shown in this catalog may be available. Contact us for more information
uSee pages 18 & 19 for Flare conversion adapters
u
u
08YSKK*
Underground Water Service Fittings & Couplings
21A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com
4/07
n Y-Branches
08Y2CC 08Y2MT* 08Y2M2*08Y2MCSIZES AVAILABLESize Single Multiple FLArE x MNPt x MNPt x MNPt x MNPt x
End Ends FLArE FLArE Q CtS Comp t CtS Comp 22 CtS Comp1" x 3/4" 1" 3/4" ●
1" x 1" 1" 1" ●
11⁄4" x 3/4" 11⁄4" 3/4" ●
11⁄4" x 1" 11⁄4" 1" ●
11⁄2" x 1" 11⁄2" 1" ● ● ● ● ●
2" x 1" 2" 1" ● ● ● ● ●
08Y3CC 08Y3MCSIZES AVAILABLE
4765
Size Single Multiple FLArE x MNPt xEnd Ends FLArE FLArE
11⁄2" x 3/4" 11⁄2" 3/4" ● ●
11⁄2" x 1" 11⁄2" 1" ● ●
2" x 1" 2" 1" ● ●
08Y4CC 08Y4TT* 08Y422*08Y4QQ*SIZES AVAILABLESize Single Multiple FLArE x t CtS Comp x Q CtS Comp x 22 CtS Comp x
End Ends FLArE t CtS Comp Q CtS Comp 22 CtS Comp2" x 3/4" 2" 3/4" ● ● ● ●
2" x 1" 2" 1" ● ● ● ●
*Insert stiffeners are required on all flexible plastic connections. See page 5.
08Y4MC 08Y4MT* 08Y4M2*SIZES AVAILABLESize Single Multiple MNPt x MNPt x MNPt x MNPt x FNPt x
End Ends FLArE t CtS Comp Q CtS Comp 22 CtS Comp FNPt2" x 3/4" 2" 3/4" ● ● ● ●
2" x 1" 2" 1" ● ● ● ●
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLY
08Y2MQ*
08Y4MQ*
u u
u u
u
u
uSee pages 18 & 19 for Flare conversion adapters
Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com22 4/07
n U-Branches
nto order U-Branches: Model No. 08UCM 1 x 3/4 x 7.5 means:08 U C M 1 x 3/4 x 7.5 Size
Single opening end X
Multiple opening endX
Spread
U-Branchestype of connection -Single opening endC = Copper flareF = FNPTJ = Male Meter ThdK = C903 Comp.L = Copper flare, less nutM = MNPT
type of connection-Multiple openings(Same codes as single open-ing end)Style
U = Standard U-branchT = Angle U-branch
08UCM 08UTM*
08UFF*
08UQM*SIZES AVAILABLESize Single Multiple FLArE x t CtS Comp x Q CtS Comp x 22 CtS Comp x
End Ends Spread MNPt MNPt MNPt MNPt1" x 3/4" x 6.5" 1" 3/4" 6.5" ● ● ● ●
1" x 3/4" x 7.5" 1" 3/4" 7.5" ● ● ● ●
1" x 1" x 7.5" 1" 1" 7.5" ● ● ● ●
1" x 3/4" x 14"▲ 1" 3/4" 14" ● ● ● ●
1" x 1" x 18" 1" 1" 18" ● ● ● ●
11⁄2" x 3/4" x 7.5" 11⁄2 3/4" 7.5" ● ● ●
11⁄2" x 1" x 9" 11⁄2 1" 9" ● ● ●
08U2M*
08U3M* 08U5M08U4MSIZES AVAILABLESize Single Multiple 3Q PEP Comp x 33 PEP Comp x 44 PVC Comp x 55 IP Comp x End Ends Spread MNPt MNPt MNPt MNPt1" x 3/4" x 7.5" 1" 3/4" 7.5" ● ● ● ●
11⁄2" x 3/4" x 7.5" 11⁄2 3/4" 7.5" ● ●
08UFM 08UMMSIZES AVAILABLESize Single Multiple FNPt x FNPt x MNPt x Male Meter thread End Ends Spread FNPt MNPt MNPt x Meter Swivel Nuts1" x 3/4" x 6.5" 1" 3/4" 6.5" ●
1" x 3/4" x 7.5" 1" 3/4" 7.5" ● ●
1" x 1" x 7.5" 1" 1" 7.5" ● ●
1" x 3/4" x 14"▲ 1" 3/4" 14" ● ●
1" x 1" x 8" ▲ 1" 1" 8" ● 1" x 1" x 14"▲ 1" 1" 14" ● 1" x 1" x 18" 1" 1" 18" ● ● ●
11⁄2" x 3/4" x 7.5" 11⁄2 3/4" 7.5" ●
11⁄2" x 1" x 9" 11⁄2 1" 9" ●
11⁄2" x 1" x 12"▲ 11⁄2 1" 12" ●
2" x 1" x 9" 2 1" 9" ●
SIZES AVAILABLESize Single Multiple FLArE x FNPt x MNPt x t CtS Comp x 22 CtS Comp x End Ends Spread MNPt MNPt MNPt MNPt MNPt1" x 3/4" x 6.5" 1" 3/4" 6.5" ● ● ● ●
11⁄2" x 1" x 12"▲ 11⁄2 1" 12" ●
*Insert stiffeners are required on all flexible plastic connections. See page 5.
N = Meter Swivel NutQ = McQuik Comp.T = T-Comp.Z = 3Q Comp.2 = 22 Comp.3 = 33 Comp.4 = 44 Comp.5 = 55 Comp.
▲ Assembled and tested
▲ Assembled and tested
08TFM* 08T2M*08TTM*08TMM08TC M*
08UZM*
For C903 tube - Replace "Q" with "K". On "Q" Series options only 3/4" x 1" ONLY
n Angle U-Branches
u
u
uSee pages 18 & 19 for Flare conversion adapters
08UJN
U-Branches available with valve assembled - Contact Factory
Underground Water Service Fittings & Couplings
23A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com
4/07
n Miscellaneous Service FittingsSwivel with increasing IP threadGasket included
4783S 4783ST* 4783S-22*4783SQ*SIZES AVAILABLE
Size SWIVEL NUt Swivel x Swivel x Swivel x Swivel x Swivel x Swivel x FLArE t CtS Comp Q CtS Comp 22 CtS Comp 3Q PEP Comp 33 CtS Comp5/8" 5/8" 3/4" ● ● ●
3/4" 3/4" 3/4" ● ● ● ●
1" 1" 1" ● ● ●
1" x 3/4" 1" 3/4" ● ● ● ● ●
4000 46604756Quarter Bend
Swivel with increasing IP thread-4000G gasket included
two-part unionwith “wedding ring”
Copper Flare to Polyethylene Insert Coupling
4755G gasket includedSIZES AVAILABLE
Size END END Swivel x MNPt GASKEt SWIVEL FLArE x FLArE FFLr x Barbed FOr 4000 SIZE1/2" 1/2" 1/2" ●
3/4" 3/4" 3/4" ● 4749G 1" ● ●
1" 1" 1" ● ● 11⁄4" ● ●
11⁄4" 11⁄4" 11⁄4" ● 11⁄2" ●
11⁄2" 11⁄2" 11⁄2" ● ● 2" ●
2" 2" 2" ● ● 21⁄2" ● ●
3206 3208
4775N
3209SIZES AVAILABLE AWWA CC x MNPt x AWWA CC x MNPt x MNPt x MFLr x Size tHrEAD HEAD with 5/8" inside with 5/8" inside SQUArE SQUArE Square Head SQUArE Driving thread Driving thread HEAD HEAD (Short) HEAD 1/2" 1/2" 1/2" ● ● ●
5/8" 5/8" 5/8" ● ●
3/4" 3/4" 3/4" ● ● ● ● ● ●
1" 1" 1" ● ● ● ● ●
11⁄4" 11⁄4" 11⁄4" ● ● ●
11⁄2" 11⁄2" 11⁄2" ● ● ● ●
2" 2" 2"
Underground Water Service Fittings & Couplings
A.Y. McDONALD MFG. CO. • P.O. BOX 508 • DUBUQUE, IA 52004-0508 • tOLL FrEE 800-292-2737 • FAX [email protected] • www.aymcdonald.com24 4/07
NEW!4770 Tape Measure
with O.D. ScaleSide One - O.D. scale • Side Two - inches/metric
79" - 200cm
n General Information
Suffix -22, T or Q
Suffix -33
NOtE: Materials meet or exceed A.W.W.A. standard C-800.
ABBrEVIAtIONS / DEFINItIONSAWWA American Water Works Association Standard Thread / Corporation Cock, this thread has a steeper taper than Male National Pipe ThreadsCtS Copper Tube Size, copper tube (type K or L) or copper tube size polyethylene (ASTM D2737 SDR 9) or Polybutylene (ASTM D2666 SDR 9), insert stiffeners are required when using polyethylene or polybutylene.FFLR Female Copper Flared Connection Thread / inside thread, includes copper gasket.FLR Flared end with nut, for use with copper tubeFNPt Female National Pipe Thread / inside tapered threadIP Iron Pipe / Galvanized Iron Pipe (not threaded) Suffix -55IPS or PEP I.D. based polyethylene pipe, for use with polyethylene (ASTM D2239 SIDR 7) or Polybutylene (ASTM D 2662 SIDR 7), insert stiffeners are required when using polyethylene or polybutylene.MFLR Male Copper Flared Connection Thread / outside thread.MNPt Male National Pipe Thread / outside tapered threadPE PolyethylenePVC Polyvinyl Chloride, ridged plastic pipe, Schedule 40 or 80 only (ASTM D1785) Suffix -44
MODEL 4692 - 3/4", 1"Converts 3/4" & 1" CTS compression to 3/4" or 1" Flare
EPDM O-RINGS
COPPER TUBECOPPERFLARE NUT
CTS COMPRESSION TOFLARE INSERT
McDONALD CTS COMPRESSION BODY OR ENDPIECE
Flare Nut 4692 CTS Compression End
uSee pages 18 & 19 for Flare conversion adapters
NEW!
CtS COMPrESSION PLUGMODEL 4693 - 3/4", 1"Plugs 3/4" & 1" CTS
W A RNING:W A RNING:W A RNING:W A RNING:W A RNING:W A RNING:W A RNING:W A RNING:W A RNING:W A RNING:W A R NING: I t i s u n l a w f u l i n C A L I F O R NIA & VERMONT (effective 1/1/2010); MARYLAND (effective 1/1/2012); LOUISIANA (effective 1/1/2013) and the UNITED STATES OF AMERICA (effective 1/4/2014) to use any product in the installation or repair of any public water system or any plumbing in a facility or system that provides water for human consumption if the wetted surface area of the product has a weighted average lead content greater than 0.25%. This prohibition does not extend to service saddles used in California, Louisiana or under USA Public Law 111-380.
WA rNING:
W A rN I N G : 8 0 0 . 2 9 2 . 2 7 3 7 |
FAX 800.832.9296 | [email protected] | www.aymcdonald.comWATERWORKS | PUMPS | PLUMBING VALVES | GAS VALVES
A.Y. McDonald Mfg. Co.