RAPIDHEAT™ BURNERThis burner delivers 19,000 BTUs of power, allowing you to rapidly reach and maintain high temperatures for searing and stir-frying.
KNOB LIGHTINGOur knobs light up red when the burner is on so no simmer will go unnoticed.
GRIDDLE PLATEThe non-stick coated griddle accessory provides an extra-large cooking surface for meats, pancakes or other food usually prepared in a frying pan or skillet.
WIFI-ENABLEDWith burner monitoring and push notifications, you can make sure your cooktop is operating perfectly, even when you step away from the kitchen. You'll also be able to ensure everything is running smoothly with Smart Diagnosis.
InnovationWiFi-Enabled for ThinQ® Control with iPhone / Android App
Yes
Remote Monitoring Yes
Cooktop FeaturesCooktop Surface Stainless SteelNumber of Burners / Elements 5Sealed Gas Burners (Brass) YesFuel Type LNG / LPGContinuous Grates 3Dishwasher Safe Grates YesCooktop Control Knobs with Red LED Back Lighting
Yes
Cooktop PerformanceBurner Power BTU/h (NG)
Left Rear 9,100 / 9,100Right Rear 5,000 / 5,000Center Rear (RapidHeat) 19,000 / 15,000Left Front 9,100 / 9,100Right Front 12,000 / 9,500
Technical SpecsEnergy Source Gas GasAlternative Energy Source LP Gas LP GasLP Conversion Kit Included YesRequired Power Supply 120VAC, 60Hz
*These warranties give you specific legal rights and you may have other rights that vary from state to state. For complete warranty details, refer to your Use & Care manual.
Warranty Summary*Limited Warranty, Parts & Labor 3 Years
COOKTOP AND CUTOUT DIMENSIONS
To ensure accuracy, it is best to make a template when cutting the opening in the counter
GAS COOKTOPS DIMENSIONS AND CLEARANCES
MAINTAIN THE FOLLOWING MINIMUM CLEARANCE DIMENSIONS COOKTOP AND CUTOUT DIMENSIONS
Provide enough clearances between the cooktop and adjacent combustible surfaces. These dimensions must be met for safe use of your cooktop. The location of the Electrical outlet and pipe opening may be adjusted to meet specific requirements. The cooktop may be placed with 2 3/4 ” clearance to the back wall.
To ensure accuracy, it is best to make a template when cutting the opening in the counter
13" (330 mm) MAX. Depth of unprotectedoverhead cabinets
30" (762 mm) MIN. clearancefrom countertop to unprotected overhead surface
36"(914 mm)
MIN. 18" (457 mm) MIN. height from countertop to nearest cabinet on either side of unit
11 13/16" (300 mm) MIN. clearance from cutout to side wall on the left of unit.
11 13/16" (300 mm) MIN. clearance from cutout to side wall on the right of unit.
2 3/4" (70 mm) MIN. between cutout and the wall behind the cooktop
1 5/8" (41.3 mm)MIN. from frontedge of cutoutand front edge
of countertop
21 11/16" (551 mm)depth
19 11/16"(500 mm)depth cut
19 3/8"(492 mm)
depth
36" (914 mm)width
33 5/8" (854 mm)width
33 15/16"(862 mm)width cut
3 3/4" (95 mm) height
COOKTOP AND CUTOUT DIMENSIONS
Page 3 of 3 | Effective 7/20 | WCAG
UPCG3654ST36-INCH GAS COOKTOP
DIMENSIONS AND CLEARANCES
Provide enough clearances between the cooktop and adjacent combustible surfaces. These dimensions must be met for safe use of your cooktop. The location of the Electrical outlet and pipe opening may be adjusted to meet specific requirements. The cooktop may be placed with 2 3/4” clearance to the back wall.
MAINTAIN THE FOLLOWING MINIMUM CLEARANCE DIMENSIONS
GAS COOKTOPS DIMENSIONS AND CLEARANCES
MAINTAIN THE FOLLOWING MINIMUM CLEARANCE DIMENSIONS COOKTOP AND CUTOUT DIMENSIONS
Provide enough clearances between the cooktop and adjacent combustible surfaces. These dimensions must be met for safe use of your cooktop. The location of the Electrical outlet and pipe opening may be adjusted to meet specific requirements. The cooktop may be placed with 2 3/4 ” clearance to the back wall.
To ensure accuracy, it is best to make a template when cutting the opening in the counter
13" (330 mm) MAX. Depth of unprotectedoverhead cabinets
30" (762 mm) MIN. clearancefrom countertop to unprotected overhead surface
36"(914 mm)
MIN. 18" (457 mm) MIN. height from countertop to nearest cabinet on either side of unit
11 13/16" (300 mm) MIN. clearance from cutout to side wall on the left of unit.
11 13/16" (300 mm) MIN. clearance from cutout to side wall on the right of unit.
2 3/4" (70 mm)MIN. between cutout and the wall behind the cooktop
1 5/8" (41.3 mm)MIN. from frontedge of cutoutand front edge
of countertop
21 11/16" (551 mm)depth
19 11/16"(500 mm)depth cut
19 3/8"(492 mm)
depth
36" (914 mm)width
33 5/8" (854 mm)width
33 15/16"(862 mm)width cut
3 3/4" (95 mm) height
CUTOUT DIMENSIONS – UNDERCOUNTER INSTALLATION
25" (635 mm)Typical
Countertop Depth
23 1/2"(597 mm)Min. abovesupportplatform
28 15/16" Min.(735 mm)29" Max.(737 mm)
3/4" (19 mm) Support platform
required
36" (914 mm)Recommended Countertop Height
5"(127 mm)
Gas and electrical connections for 30" gascooktop must be located in an adjacentaccessible location to the right. For a 36"gas cooktop, the connections may be madeto the left.
240 V / 208 VJunction Box Location(Junction box may bein adjacent cabinet)
2 3/4" (70 mm) ~ 4" (102 mm)
Allow 1/2" (13 mm) for flange overlapon top and sides
28 1/2" Min. (724 mm)28 5/8" Max. (727 mm)
*24" Min.(610 mm)
25" Min. (635 mm) cutout depth required for undercounter flush installation.Refer to installation art for flush installation in wall cabinet for required cutout dimensions.
*
CUTOUT DIMENSIONS – INSTALLED ABOVE SIGNATURE KITCHEN SUITE SINGLE WALL OVEN
DIMENSIONS AND CLEARANCES
MAINTAIN THE FOLLOWING MINIMUM CLEARANCE DIMENSIONS
CUTOUT DIMENSIONS – INSTALLED ABOVE SIGNATURE KITCHEN SUITE SINGLE WALL OVEN
