Update Alert: Firmware updates are posted the web on a regular …€¦ · ()white conn. at...

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI

© 2017 Directed. All rights reserved.

Index

® H is a registered trademark and property of its y.yundai respective compan

Installation Guide

Update Alert: Firmware updates are posted the web on a regular basis. We recommendon

that you check for firmware and/or install guide updates prior to installing this product.

The firmware for 2 is an all-in-one door lock and override module compatible withHYUNDAI4 DBALLspecific vehicles.Santa Fe

This module can only be flashed and configured using Xpress at www.directechs.com orVIPusing the Directechs Mobile application for smartphones. Refer to the Module Programmingsection non page for more information.

Vehicle Application Guide ....... .................. ..................................... ............................... ......................................................

Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )Type 1.............. ..... .................................................................................................................... ..........................................Type .............. ..... ..........................................2 .......................................................................... ..........................................

ProgrammingModule Programming ...................... .............................................................................. .......... ...........................................Module Reset.. ...................................................................................................................................................................Hard ... ....Reset.. ................................................................................................................................................................Feature & Option List..........................................................................................................................................................Feature Programming.........................................................................................................................................................

LED Diagnostics & Troubleshooting...................................................................................................................................

Limited One-Year Consumer ........Warranty.......................................................................................................................

Quick Reference Guide......................................................................................................................................................

02

0305

0708080909

10

12

13

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI


Vehicle Application GuidePage 2

The table below lists the vehicles and features which are compatible with this product. Refer to the following pages formore information on installation wiring, programming and troubleshooting for these vehicles.

Vehicles

2017

2016

2015

2014

2013

PK

-Im

mobilizer

Bypass-D

ata

No

Key

Req'd

AV

-Panic

Mode

Activ

atio

n

DL-A

rmF

acto

ryS

ecurity

DL-D

isarm

Facto

ryS

ecurity

DL-D

oor

Lock

Contr

ol

DL-D

oor

Unlo

ck

DL-D

river

Priority

Unlo

ck

DL-T

runk

/H

atc

hR

ele

ase

FO

B-C

ontr

ol o

fafterm

ark

etala

rmw

ithO

EM

rem

ote

RS

-Tach

/R

PM

Outp

ut

SS

-Entr

yM

onito

ring

ALL

Door

Pin

s

SS

-Entr

yM

onito

ring

Hood

Pin

SS

-Entr

yM

onito

ring

Tru

nk/H

atc

hP

in

ST

-Bra

ke

Sta

tus

(footbra

ke)

ST

-Igniti

on

Sta

tus

Hyundai

Santa Fe (Smart Key) 2 2 1 1 1 • • • • • • • • D • • • • • D

Santa Fe Sport (Smart Key) 2 2 1 1 1 • • • • • • • • D • • • • • D

Legend:

D: Data-to-Data (D2D) PK: Transponder & Immobilizer Override

•: D2D & Wire-to-Wire (W2W) AV: Horn & Lights Controls

DL: OE Door Lock & Alarm Controls

FOB: Sync CAN Interface w/ FOB Remote

RS: Remote Start & Engine Controls

SS: Integrated Security & Monitoring

ST: Function/Feature Status

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI


1

11

21

39

98765432

1918171615141312

2928272625242322

3837363534333231

4746454443424140

10

20

30

48

(+) Starter Output

(+) Accessory Output

(+) Ignition Output

Not required in D2D mode.

[1] ( ) Tach InputAC

(+) Brake Input

(-) Trunk Status Input

(-) Door Status InputR

em

ote

Sta

rter

(-) (Status)GWR

(-) OutputLock

(-) OutputUnlock

(-) OutputTrunk

(-) Ground

(-) Hood Status Input

1: (-) Lock InputGreen:

2: (-) Unlock InputBlue:

3: (-) Trunk InputRed/White:

10: (-) (Status) InputBlue/White: GWR

[ ]1 ( ) Tach Output: 5AC Violet/White:

(+) Brake Status Output: 6Gray:

(-) Hood Status Output: 12Blue/Red:

Immo. Data: 11Orange/Black:

(-) Door Status Output: 3Green/White:

(-) Trunk Status Output: 4Red/Black:

(+) 12V (+) 12 : 13V Red:

(-) Ground (-) Ground: 14Black:

FTCAN High: 5Orange/Green:

FTCAN Low: 6Orange/Brown:

(-) TS 2 Output: 2P Green/Black:

(-) P 1TS 1 Output: Black/White:

Refer to the wiring andVehicle Wiring Reference hartC on page 4 for more information on specific connections.

(+) 12V Input

(+)12V:Red, pin 4

I/P-B(white conn. on front

of dash fuse box)

(-) Parking Lights:Pink, pin 15

16151413121110

87654321

9

(-) Parking ightsL Output

B- High:CANBlue, pin 24

C- LowCAN :Orange, pin 14

C- High:CANGreen, pin 6

11MF( in rive ick anel)white conn. d r k p

OBDII Diagnosticconnector

B- Low:CANRed, pin 33

46

2611

43

33

188

36

211

45

35

25

20

10

44

34

24

199

3

12

22

27

37

13

23

28

38

2

32

39

40

41

42

29

30

31

14

15

16

17

45

67

M01-L(white conn. at headl s )ight witch

EMS COM:White/Orange,p 32in

(+) Ignition:Green, pin 21

(+) Accessory:Yellow, pin 3

(+) Starter:Pink, 11pin

1 8

169

HS CAN High 3: Tan/Black:

HS CAN Low 4: Tan:

4321

EM11(black conn.in driver kick panel)

11 9101213141516

1 4 5 83

(-) PTS 1:Orange/Black,

pin 3

M04( at switch)black conn. PTS

2

(-) PTS 2:Yellow/Orange,

2pin

6 7

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OB IID s

Page 3

[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.

10

2DBALL

RF

Prog. Button

LED

4

14

12

2

TX

(-) Ground

RX

(+)12V

P#: 2D65XKD

Installation Type 1

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI


Type - Vehicle Wiring Reference Chart1Page 4

Locating components in the vehicle

Function Color Pin Polarity Location Color Pins

12V Red 1 (+) I/P-B, front of dash fuse box. White 4

PTS 1 Orange/Black 3 (-) M04, PTS switch. Black 12

PTS 2 Yellow/Orange 2 (-) M04, PTS switch. Black 12

C-CAN High Green 6 Data OBDII. Black 16

C-CAN Low Orange 14 Data OBDII. Black 16

Parking Lights Pink 15 (-) M01-L, headlight switch. White 16

Starter Pink 11 (+) EM11, driver kick panel. Black 46

Ignition Green 21 (+) EM11, driver kick panel. Black 46

Accessory Yellow 3 (+) EM11, driver kick panel. Black 46

EMS COM White/Orange 32 Data EM11, driver kick panel. Black 46

B-CAN High Blue 24 Data MF11, driver kick panel. White 48

B-CAN Low Red 33 Data MF11, driver kick panel. White 48

12V Red 1 (+) I/P-B, front of dash fuse box. White 4





Parking Lights Pink 15 (-) M01-L, headlight switch. White 16

Starter Pink 11 (+) EM11, driver kick panel. Black 46

Ignition Green 21 (+) EM11, driver kick panel. Black 46

Accessory Yellow 3 (+) EM11, driver kick panel. Black 46

EMS COM White/Orange 32 Data EM11, driver kick panel. Black 46



Wire Information

Santa Fe (Smart Key) 2013-2015

Santa Fe Sport (Smart Key) 2013-2015

Connector Information

Driver Kick Panel

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI


(+) Starter Output

(+) Ignition Output

Not required in D2D mode.

[1] ( ) Tach InputAC

(+) Brake Input

(-) Trunk Status Input

(-) Door Status Input

Rem

ote

Sta

rter

(-) (Status)GWR

(-) OutputLock

(-) OutputUnlock

(-) OutputTrunk

(+) OutputAccessory

(-) Ground

(-) Hood Status Input

1: (-) Lock InputGreen:

2: (-) Unlock InputBlue:

3: (-) Trunk InputRed/White:

10: (-) (Status) InputBlue/White: GWR

[ ]1 ( ) Tach Output: 5AC Violet/White:

(+) Brake Status Output: 6Gray:

(-) Hood Status Output: 12Blue/Red:

Immo. Data: 11Orange/Black:

(-) Door Status Output: 3Green/White:

(-) Trunk Status Output: 4Red/Black:

(+) 12V (+) 12 : 13V Red:

(-) Ground (-) Ground: 14Black:

FTCAN High: 5Orange/Green:

FTCAN Low: 6Orange/Brown:

(-) PTS 2 Output: 2Green/Black:

(+) 12V Input

(+)12V:Red, pin 1

1

(-) ParkingLights:Pink, pin 15

C- LowCAN :Orange, pin 14

C- HighCAN :Green, pin 6

16151413121110

87654321

9

(-) Parking lights

M01-L( )white conn. at headlight switch

EM 31(white conn. in

driver kick panel)

OBDIIDiagnosticconnector

1 8

169

HS CAN High 3: Tan/Black:

HS CAN Low 4: Tan:

Refer to the wiring andVehicle Wiring Reference hartC on page 6 for more information on specific connections.

11 9101213141516

1 4 5 83

(-) PTS 1:Orange/Black,pin 3

M04( at switch)black conn. PTS

25

6

20

21

22

37

35

34

29

28

27

38

39

40

41

42

43

44

55

48

58

11

57

36 7

25

(+) Ignition:Green,

5pin 2 EMS COM:White/Orange,

36pin

(+) Accessory:Yellow,pin 19

(+) Starter:Pink, pin 7

EM11( in rive ick anel)red or white conn. d r k p

2

(-) P 1TS 1 Output: Black/White:

(-) PTS 2:Yellow/Orange,

2pin

6 7

19

30

B- Low 39CAN : pinRed,

B- HighCAN :Blue, 29pin

MF11( inwhite conn.

d r k prive ick anel)29

39

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OB IID s

[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.

10

2DBALL

RF

Prog. Button

LED

4

14

12

2

TX

(-) Ground

RX

(+)12V

P#: 2D65XKD

Installation Type 2Page 5

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI


Page 6

Type - Vehicle Wiring Reference Chart2

Locating components in the vehicle

Driver Kick Panel

MF11(68-WHT)

Function Color Pin Polarity Location Color Pins

Santa Fe (Smart Key) 2016-2017

12V Red 1 (+) EM31, drivers kick panel. White 1





Parking LightsPink 15 (-) M01-L,headlight switch. White 16

Starter Pink 7 (+) EM11, driver kick panel. Red or White 58

Ignition Green 25 (+) EM11, driver kick panel. Red or White 58

Accessory Yellow 19 (+) EM11, driver kick panel. Red or White 58

EMS COM White/Orange 36 Data EM11, driver kick panel. Red or White 58



Santa Fe Sport (Smart Key) 2016-2017

12V Red 1 (+) EM31, drivers kick panel. White 1





Parking LightsPink 15 (-) M01-L, headlight switch. White 16

Starter Pink 7 (+) EM11, driver kick panel. Red or White 58

Ignition Green 25 (+) EM11, driver kick panel. Red or White 58

Accessory Yellow 19 (+) EM11, driver kick panel. Red or White 58

EMS COM White/Orange 36 Data EM11, driver kick panel. Red or White 58



Wire Information Connector Information

EM11(58-WHT)

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI


Page 7

Module Programming

1Solid

2XENGINESTARTSTOP

PUSHDo NOT

press the

brake pedal

IMPORTANT: NOTDo press the brake pedal.the Push-To-Start (PTS) button to turnPress twice

the ignition ON.2

Important

Refer to the Diagnostics section on page for more information and for troubleshooting purposes.LED s 9-10

4 1XENGINESTARTSTOP

PUSHPress the Push-to-Start (PTS) button more to turn the ignition OFF.once

You have successfully completed the programming sequence.module

Wait until the LED turns solid red.ON

Note: To skip the transponder programming and use convenience features only, pressthe 5 times. The will turn orange then proceed to step 2.programming button LED

&

Flashes3

The orange flashes then the green turns for 3 secondsLED LED ONand shuts off.

Note: When skipping transponder programming, the orange LEDflashes then the orange turns solid green or orange for 3LEDseconds and shuts off.

&OffSolid Green or

Orange x3 sec

Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check toensure everything is correct prior to moving onto the next step.

Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP

When the flashing operation is successful, you can proceed with the programming instructions below.

OR

If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses tothe module, then connect the 4-pin D2D harness.

D2D Installation

W W Installation2

If required for your installation, connect the 10-pin and 12-pin harnesses to themodule, then connect the 14-pin harness to the module.

10-pinD2D

1st

12-pin14-pin

2nd

3rd

10-pinD2D

1st

4th

12-pin14-pin

2nd

3rd

Flashing a module using your computer:

1. Connect the interface module to your computer using theXKLoader2.

2. Go to www.directechs.com using Internet Explorer, andselect the button.Flash Module

3. Follow the instructions to select your vehicle, installationtype, and configure your options.

4. Once you have configured the firmware options, click on theFLASH button.

Flashing a module using your smartphone or tablet

1. Connect the interface module to your oader3.XKL

2. Launch the Directechs Mobile app on your smartphone ortablet.

3. Select and follow the on screenFLASH YOUR MODULEinstructions.

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI


Page 8

1If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

10-pinD2D

1st

12-pin14-pin

2nd

4th

3rd

Warning gainst xecuting a Hard Reset!A EA hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (suchas and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List

2

Solid

&Release

3 Release the programming button. The turns solid red.LED ON

Module Reset

Hard Reset

2 & &

1

Wait 3 seconds until the orange then release theLED turns solidONp The turns solid red.rogramming button. LED ON

If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

10-pinD2D

1st

12-pin14-pin

2nd

4th

3rd

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashedto the module using the web config tool will not be affected.

Solid Release Solid

Solid Flashes

&Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsONuntil the andLED starts to flash orange red.

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI


Feature Option List&Page 9

* Default Option

Feat. Operation Flashes/Options Description

1. No RF Output* Module is connected to a remote starter using a standard installation.

2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).

3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).

1. Driver Priority* Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.

2. All Unlocks all doors on first press.

1. DisabledThe OEM alarm will not be controlled by DBALL2 upon remote start. No disarm or arm command will be

executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.

2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at the

beginning of the sequence, and relock after start and shutdown.

3. Enabled*

Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in

the remote start sequence, only when required. The reason for this is, factory alarm control must often be done

by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the horn to

honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock status to detect if the

disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm

will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so that the factory

alarm control is not done twice. A remote starter, for which the Safelock feature is active, will work perfectly with

this option and will make it invisible to the user.

Smart OEM Alarm

Control3

RFTD Output

Type1

2Unlock Driver

Priority

It is recommended to configure all features and options listed below thethe using configuration tool found on the moduleflashing page on www.directechs.com. The web offers more options; however, manual configuration of the features ispossible using the information on this page.

To enter feature programming routine- Turn t , thenhe ignition .ON OFF- Within 5 seconds, press and the rogramming button turns after 3 seconds . Release theHOLD LED ONp until the orange ( )

Programming button.- The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicateLED LEDwill flash green once slowly red

the current option of feature 1 . repeat(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence willuntil .a new command is entered

Changing feature options- Press the arm or disarm button on aftermarket transmitter to change the option of the selected feature.lock/ unlock/- The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowlyLED LEDred

the number of times to indicate the current feature. repeat until .The flashing sequence will a new command is entered

Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature.- The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly toLED LED

indicate the current option of the current feature. repeat until .The flashing sequence will a new command is entered

When the maximum number of features or options is reached, the will start flashing again from the first feature or option.LED

Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.

Exiting feature programming- No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programmingLED ON

sequence.OR

- Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm theHOLD LED ONend of the programming sequence.

Feature ProgrammingProgramming

Button

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI


Page 10

LED Diagnostics & Troubleshooting

LED Description Troubleshooting

Module has no power.

Make sure the D2D harness is connected or that the 12

Volt is present between the red and black wires. If the

12 Volt is present, the module may be defective.

Waiting to begin the programming sequence.Ensure the correct programming procedure is being

followed.

Initialization failed.Reset the module and complete the programming again.

If the issue persists, please contact Technical Support.

Transponder functions were skipped.

(If compatible) when RXT mode is not desired or

convenience features are needed, please reset and

reprogram the module.

All required CAN networks has been detected. Normal operation.

1 of 2 CAN networks has been detected. Normal operation

Key2GO initiated.Please follow the steps indicated in “Module

programming” to complete the Key2GO programming.

Module was successfully programmed with all functions. Normal operation

Module was successfully programmed without

transponder functions.Normal operation.

CAN2 not detected.

Check the CAN2 Orange/Green and Orange/Brown wire

connections. Wake up the data bus by turning the

ignition on and try again. If your installation does not

require this connection, skip this step by pressing the

programming button 5 times.

J1850 not detected.Check the J1850 wire connection. Wake up the data bus

by turning the ignition on and try again.

CAN1 not detected.

Check the CAN1 Tan and Tan/Black wire connections.

Wake up the data bus by turning the ignition on and try

again. If your installation does not require this

connection, skip this step by pressing the programming

button 5 times.

Bypass data not detected.

Check the bypass line connection. If more than one wire

is used, make sure they are not inverted. Ensure the

vehicle still operates correctly using the factory key.

Bypass processing error.

The bypass calculation failed. Reset the module and try

again. If the condition persists, please contact Technical

Support.

ISO 1 not detected.

The Yellow/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

ISO 2 not detected.

The Orange/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

MUX not detected.

The Violet/Green or Violet/Brown wire did not detect the

expected voltage value. Refer to "Installation (wiring

diagrams & vehicle wiring reference charts)" to check

the connections.

Module Programming

Module Programming - Error Codes

Solid red

Flashes redx 1

Flashes redx 1

Flashes redx 2

Flashes redx 3

Flashes redx 4

Flashes redx 5

Flashes redx 6

Flashes redx 7

Solid greenx 3 secs

Flashesgreen

Solid orange

Flashes red& green

Off

Flashesorange

Flashesorangeslowly

Solid orangex 3 secs

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI


LED Description Troubleshooting

OBDII feature is not supported.The diagnostic data bus was not detected, therefore the

SmartStart features will be limited.

Ground When Running (Status) command received. The module has initialized the remote start sequence.

Ignition ON command received.The module has received the Ignition ON command and

is processing the remote start sequence.

Start ON command received.The module has received the Start ON command and is

processing the remote start sequence.

PTS shutdown error.The PTS output from the module was not activated due

to safety protection.

CAN bus incorrectly detected.

Verify the CAN1 and CAN2 connections. Refer to

“Installation (wiring diagrams & vehicle wiring reference

charts)” to check the connections.

LOCK command received.

UNLOCK command received.

TRUNK command received.

AUX1 command received.



Takeover successful. Normal operation.

Runsafe was not disabled.No UNLOCK command was received prior to opening the

door, or the 45 second timer expired in takeover mode.

Brake was not detected.The brakes were not detected, which prevents the

system from shutting down the vehicle.

Smart key was not detected.The smart key was not detected, which prevents the

system from shutting down the vehicle.

Speed was detected.The vehicle was detected as moving, which prevents the

system from shutting it down.

External module synchronization

Commands

Activation Ground When Running (Status)

If the bypass module fails to flash, it did not receive the

signal. Commands can come from RF or D2D.

Shutdown codes

(Flashes red,red thenorange) x 10

Flashes red& orange

Flashes redx 21

Flashes redx 2

Flashes redx 4

Flashes redx 10

Flashes redx 1

Flashes redx 3

Flashesgreen

Flashesgreenquickly

Flashesgreen x 1

Flashesorange x 1

Flashesorange x 2

Flashesorange x 3

Flashesorange x 5

Flashesorange x 4

Flashesorange x 6

Page 11

Rev.: 20170814

Platform: DBALL2

Firmware 4: HYUNDAI


For a period of from the date of purchase of a Directed Electronics remote start or security product, DirectedONE YEARElectronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, theDIRECTEDsecurity or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or materialunder normal use, provided the following conditions are met: the Part was purchased from an authorized dealer;DIRECTEDand the Part is returned to , postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing theDIRECTEDfollowing information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and completeproduct and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to itsintended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation orother causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING, , ,BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY, , ,FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUALPROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY, ;PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS,PRODUCTS DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALLACTS OF.THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR. AINSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS, , , ,AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION, ,LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING, , . A ADIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF,CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE.DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED.TO THE AUTHORIZED DIRECTED DEALER PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE’S .RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL, ,DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL, , , ,LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE, . ,MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED OPTION THEA ’SPARTAS DESCRIBED ABOVE.

This warranty only covers Parts sold within the United States ofAmerica and Canada. Parts sold outside of the United States ofAmerica or Canada are sold “ - ” and shall have , express or implied. Some states do not allow limitationsAS IS NO WARRANTYon how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warrantygives you specific legal rights and you may also have other rights that vary from State to State. does not and hasDIRECTEDnot authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of ’sDIRECTEDwebsite at: www.directed.com

920-10012-01 2013-07

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the selectvehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. : Under noDISCLAIMERcircumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for anyconsequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, norwill they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / databus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of thisproduct be liable for consequential damages sustained in connection with this product and neither assumes nor authorizesany representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; EuropeanPatent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

Limited One Year Consumer WarrantyPage 12

Quick Reference GuideDBALL2-HYUNDAI4


Vehicle Takeover

1

2

3

Stop the vehicle in a safe parking spotand put the gear in Park (P).

Pressremote start

*button

* Your aftermarket remote may differ from the model shown in the illustrations.

Stop & put vehicle in Park (P)

P&

Flashes

ENGINESTARTSTOP&

HO

LD

E vehicle withxitSmart Key

Pit Stop Mode

The Mode feature is practical when you need to stop and run an errand,Pit Stopbut wish to keep the engine running.

Note: We recommend that you always lock the doorsof your vehicle when leaving it unattended.

It is now safe to leave the exitengine running and thevehicle with the in hand.factory remote

Press the button to remote start the vehicle.*

The button willPTS flash once toit Stopindicate the vehicle is now in P

.Mode

ENGINESTARTSTOP

5

4

3

1Close the vehicle doors, hood and trunk, then press

R Sthe emote tart button on the transmitter to start*the vehicle.

2

Press the brake pedal, put the carin gear and drive off.

Press twice on the switch.PTS

Enter the vehicle, while making sure thefactory remote is inside with you.

Press the Unlock button on the factoryor aftermarket remote.*

Ready todrive off

Pressremote start

*button *

Press 2x

Press Unlockonbutton

either remote**OR

* Your aftermarket remote may differ from the model shown in the illustrations.

Complete the following steps within 45 secondsor the vehicle will shut down.

HOLD

Enter vehicleSmart Keywith

HO

LD

Quick Reference GuideDBALL2-HYUNDAI4


Button(s) Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock.

Press & hold for 1 second to remote

start.

Press & hold for 5 seconds to activate

the trunk release (optional).

Press once, then to activate the

rear hatch/tail glass release (optional).*

Press 3 times, then to activate

the panic mode.

Press once, then to reset the

remote starter runtime.

List of Available Commands

x1 +

x3 +

x1 +

* This output is configurable. see your authorized installation center for moreinformation.

Note that the information below is for Viper, Clifford and Python models. Icons andcommands may differ depending on the remote brand and model purchased. Referto your authorized installation center for more information.

Date post:	28-May-2020
Category:	Documents
Upload:	others
View:	5 times
Download:	0 times

Update Alert: Firmware updates are posted the web on a regular …€¦ · ()white conn. at...

Documents