UPGRADING FROM INJECTOR TO PRESSURE SANDBLASTING SYSTEM. UPGRADING FROM INJECTOR TO PRESSURE SANDBLASTING. WHY DO WE RECOMEND UPGRADING TO PRESSURE SANDBLASTNG SYSTEM? - PowerPoint PPT Presentation
UPGRADING FROM INJECTOR TO PRESSURE SANDBLASTING 1 UPGRADING FROM INJECTOR TO PRESSURE SANDBLASTING SYSTEM WHY DO WE RECOMEND UPGRADING TO PRESSURE SANDBLASTNG SYSTEM? Pressure sandblasting system is up to SIX times faster and more efficient than injector system. It is necessary when we have an increase in demand for sandblasting and the work has to be done faster. Usually our costumer starts with injector sandblasting system. That is very good starting point for smaller works, but as soon as demand for sandblasting increases, the costumers wants to increase speed and efficiency of their system. For that we have a very simple solution: Pressure sandblasting system. It can be upgraded from injector system with a pressure pot and a few modifications in just couple of minutes. PRESSURE POT TZP 33 SX FOR PRESSURE SANDBLASTING SYSTEM TYPE TZP 33 SX VO LU M E O F PRESSURE POT 33 l W O RKING PRESSURE 5 to 8 bar AIR C O N SU M PTIO N 0,8 -5 m ³/m in EXTER N AL D IM EN SIO N S 450x540x1070 m m W EIGH T 45 kg SANDBLASTING HO SE ø 13 x 7 m m L=7 m NO ZZLE D IM EN SIO NS 5 -8 m m TEH N IC AL D ATA INJECTOR SANDBLASTING SYSTEM
Transcript
UPG
RA
DIN
G F
RO
M IN
JEC
TO
R T
O P
RE
SS
UR
E S
AN
DB
LAS
TIN
G
1
UPGRADING FROM INJECTOR TO PRESSURE SANDBLASTING SYSTEM
WHY DO WE RECOMEND UPGRADING TO PRESSURE SANDBLASTNG SYSTEM?
Pressure sandblasting system is up to SIX times faster and more efficient than injector system. It is necessary when we have an increase in demand for sandblasting and the work has to be done faster.
Usually our costumer starts with injector sandblasting system. That is very good starting point for smaller works, but as soon as demand for sandblasting increases, the costumers wants to increase speed and efficiency of their system. For that we have a very simple solution: Pressure sandblasting system. It can be upgraded from injector system with a pressure pot and a few modifications in just couple of minutes.
PRESSURE POT TZP 33 SXFOR PRESSURE SANDBLASTING SYSTEM
TYPE TZP 33 SX VOLUME OF PRESSURE POT 33 lWORKING PRESSURE 5 to 8 barAIR CONSUMPTION 0,8 - 5 m³/minEXTERNAL DIMENSIONS 450x540x1070 mmWEIGHT 45 kgSANDBLASTING HOSE ø 13 x 7 mm L=7 mNOZZLE DIMENSIONS 5 - 8 mm
TEHNICAL DATA
INJECTOR SANDBLASTING SYSTEM
We have upgraded existing injector cabinet BLAST 3 with pressure sandblasting system.
Sandblasting cabinet FerroECOBlast BLAST3 Softline is installed in NIS GAS company from Novi Sad – Serbia.
2
UPG
RA
DIN
G F
RO
M IN
JEC
TO
R T
O P
RE
SS
UR
E S
AN
DB
LAS
TIN
G
Most of the sandblasted objects in NIS GAS company are pipes and valves.
3
UPG
RA
DIN
G F
RO
M IN
JEC
TO
R T
O P
RE
SS
UR
E S
AN
DB
LAS
TIN
G
It takes up to 6 minutes of sandblasting to finish 1 valve with injector sandblasting system.
With the same nozzle we sandblasted 1 valve in less than 1 minute using pressure sandblasting system.
4
UPG
RA
DIN
G F
RO
M IN
JEC
TO
R T
O P
RE
SS
UR
E S
AN
DB
LAS
TIN
G
5
Pressure pot TZP 33 SX is installed under cyclone and is automatically filled with abrasive material.
Mr. Novaković, from NIPEK company in Belgrade is the one “responsible” for the upgrade.
CYCLONE
PRESSURE POT TZP 33 SX
UPG
RA
DIN
G F
RO
M IN
JEC
TO
R T
O P
RE
SS
UR
E S
AN
DB
LAS
TIN
G
After successful upgrade and trial run, chief service engineer from FerroČrtalič d.o.o. Mr. Jernej Črtalič gives practical directions and instructions for use of pressure sandblasting system.
6
Everyone is looking forward to the next meeting with satisfaction after job well done. (from left: Mr. Zoran Blanuša - NIS GAS, Mr. Bojan Črtalič - FERROČRTALIČ,Mr. Milan Novaković – NIPEK, Mr. Jernej Črtalič – FERROČRTALIČ)
