indoor use only
ABC-19
-U_R0_
100kΩ
710kΩ V
Domotica Box
Coulisse B.V., Vonderweg 48, 7468 DC Enter, The Netherlands
1 2 3 4 5 6 7 8
USB
USB
RS 2
32
RS 2
32
+
-
< 4V = 0
> 6V = 1
Play
Select
Pair
Unpair
User manualDomotica Box ABC-19
WARNING: Important safety instructions. Follow all instructions,
since incorrect installation can lead to severe injury.
Do not make repairs yourself. Do not attempt to open the device
or disassemble it. You run the risk of electric shock and voiding
the limited warranty. No user-serviceable parts are inside.
WARNING:
1. General informationThe ABC-19 is a control box for motorised Coulisse blinds. Up to 8 favourite positions can be set
for each blind. When one of the eight scenario’s is played, the blinds moves to the corresponding
position. The box can be used stand-alone or integrated into an existing automation system.
ABC-19
Power supply 12-24VDC
Number of scenario’s 8
Frequency 2.4Ghz
Range (inside building) 20mtr, 2 concrete walls
1.1 Specifi cations
1.2 Buttons
Voeding 1Hz
2.3 Programming safety settings on multiple scenario’s
- An input with the highest number overrules a lower input number.
- Situation: 2 safety scenario’s are activated.
If the scenario with the highest priority is de-activated, the lower priority scenario
will be in force.
- If you have more than one Domotica Box, the input with highest number has priority.
If scenario’s with same numbers are active, the one that is activated fi rst, will be in force.
2.5 Play safety settings
For security reasons a safety setting is active if the output is high.
To deactivate a safety scenario, the output must be connected to the ground.
If a blind does not receive commands from the Domotica Box, the blind deactivates
after one hour.
Disclaimer:
© Copyright Coulisse
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, by any means,
electronic, mechanical, photocopying, recording, digital or otherwise without the written permission of the publisher.
Although this manual has been composed with the most care, Coulisse B.V. does not accept any responsibility for damage due
to mistakes and/or faults in this manual.
Coulisse B.V. reserves the right to revise the manual and to revise and/or changes its content at any time, without obligation to notify
any person or entity of such revisions or changes.
The most recent version replaces older versions of this manual. The most recent version is available at ww.coulisse.nl or contact
your Coulisse contact person.
We invite you to send remarks and comments about this manual to Coulisse at [email protected].
2. Programming2.1 Pair/unpair a blind with a Domotica box scenario
Set the blind (or blinds) in the desired position
Set the blind (or blinds) in program mode*
Select the desired scenario on the Domotica Box
1. Press
the green button to pair (add)
the scenario
to the blind
Exit program mode on the blind(s)
2. Press
the red button
to unpair (remove)
the scenario from
the blind
3. Press the red + green button at the same time
to use the scenario
as ‘stop’ command
for the blinds*
Set the Domotica Box in program mode:
Press Play and Select at the same time
Select the desired scenario*
Press the blue button (Pair) to select the safety setting:Led lights green orange
(Red = no safety setting).
2.2 Programming safety settings*A safety setting can be programmed for any scenario. In case of fi re or maintenance
the safety scenario is played. The blinds are secured and do not respond to other scenario’s.
It is also possible to block the use of remote controls.
* Only available on motors produced after august 2010.
Safety option 1 (green): When the safety scenario is activated other scenario’s are ignored.
Operating individual blinds with a remote control is still possible.
Safety option 2 (orange): When the safety scenario is activated, other scenario’s are ignored.
Operating individual blinds with a remote control is NOT possible.
Exit Program mode by pressing Play and Select
at the same time
2.4 Cancel safety settings
Set the Domotica Box in program mode:
Press Play and Select at the same time
Press and hold the Select button. After 7 seconds the LEDs light up green.
The safety settings are removed from the scenario’s.
6. Service & Support
5. Safety & Cleaning5.1 Safety
5.2 Cleaning
Follow these general rules when cleaning the outside of the device and its components:
- Make sure the device is unplugged.
- Use a damp, soft, lint-free cloth. Avoid getting moisture in openings.
- Don’t use aerosol sprays, solvents, alcohol, or abrasives.
Do not make repairs yourself. Do not attempt to open the device
or disassemble it. You run the risk of electric shock and voiding
the limited warranty. No user-serviceable parts are inside.
WARNING:
Do not make repairs yourself. Do not attempt to open the device
or disassemble it. You run the risk of electric shock and voiding
the limited warranty. No user-serviceable parts are inside.
WARNING:
- Do not let children play with the blind and/or remote control.
- Only use powersupplies or batteries that comply with the specifi cations on the motor.
- In case of malfunction, unplug the device or remove the batteries and contact your dealer.
- Take care that the blind can move freely and is not blocked by objects.
- Take care that the powersupply cable is out of reach for children.
- Do not paint the device.
- Keep the device dry.
Online Resources
For the latest information and updated manuals go to www.coulisse.nl.
Obtaining Warranty Service
First follow the advice in this booklet and then go to your local dealer.
If the product appears to be damaged or does not function properly,
go to your local dealer for instructions on how to obtain warranty service.
4. Tips & TroubleshootingPlease check www.coulisse.nl for the latest tips and troubleshooting guide.
3. Using the RSR232 interface
3. Playing scenario’s
Scenario’s can be played in three ways, using the:
- buttons on the Domotica Box
- 8 analog inputs
- RS232 interface
Scenario’s can be played subsequently with 1,5 seconds in between.
Directly play the same scenario again to stop the blinds.
Blinds can also be stopped with the remote control.
1 Using the buttons on the Domotica Box
Select the desired scenario* Press the blue Play button
to play the scenario
2 Using the 8 analog inputs
Connect the input with the ground
to play the scenario.
Safety scenario’s: a safety scenario
is active if the input is disconnected
from the ground.
Settings: baudrate 9600, 8 bits, no parity, 1 stopbit, no handshake
Protocol:The Domotica Box reacts only on incoming messages. It does not broadcast.
Command ends with ‘line feed code’. ‘Line ends’ are also allowed.
The Domotica Box reacts not on empty incoming messages.
Commands are not case sensitive.
Device commands:PLAY, INPUT and INFO
PLAY S[scenario number]
Plays the specifi c scenario. Scenario’s are S1 – S8
Example:
Command: PLAY S5
Response: OK
INFO
Reads out the software version of the Domotica Box.
INPUT I[input number]
Reads out the voltage on the specifi c input. Inputs are numbered I1 – I8
Example:
Command: INPUT I4
Response: I4=80V (8,0 Volt)
GB0
Zenden-ontvangen
Scenario indicator
The power LED
fl ashes on 2Hz.
* This can be done in three ways: press the program button on the motor or by remote control ABC-01:
Channel Select or Single Select.
** When the scenario is played the blind does not move to a position, but stops immediately.
* Safety settings can be programmed for each scenario.
* If a scenario is selected, the analog inputs are disabled. After 30 seconds the selection will be undone.
Or press the Select button until none of the scenario’s is selected.