User Manual CVHDSDI-6G · Altimium HDMI to 6G SDI Converter . Preface . Read this user manual...

CVHDSDI-6G

HDMI to 6G SDI Converter

All Rights Reserved Version: CVHDSDI-6G_2017V1.0

User Manual

Altimium www.altimium.com


Preface

Read this user manual carefully before using the product. Pictures are shown in this manual for reference only, different models and specifications are subject to real product.

This manual is only for operation instruction, please contact the local distributor for maintenance assistance. The functions described in this version were updated till December 8, 2017. In the constant effort to improve the product, we reserve the right to make functions or parameters changes without notice or obligation. Please refer to the dealers for the latest details.

FCC Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. Operation of this equipment in a residential area is likely to cause interference, in which case the user at their own expense will be required to take whatever measures may be necessary to correct the interference. Any changes or modifications not expressly approved by the manufacture would void the user’s authority to operate the equipment.

http://www.altimium.com/



SAFETY PRECAUTIONS To insure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference. Unpack the equipment carefully and save the original box and packing material for

possible future shipment. Follow basic safety precautions to reduce the risk of fire, electrical shock and injury

to persons. Do not dismantle the housing or modify the module. It may result in electrical shock

or burn. Using supplies or parts not meeting the specifications of product may cause damage,

deterioration or malfunction. Refer all servicing to qualified service personnel. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this

product near water. Do not put any heavy items on the extension cable in case of extrusion. Do not remove the housing of the device as opening or removing housing may

expose you to dangerous voltage or other hazards. Install the device in a place with fine ventilation to avoid damage caused by

overheat. Keep the module away from liquids. Spillage into the housing may result in fire, electrical shock, or equipment damage. If

an object or liquid falls or spills on to the housing, unplug the module immediately. Do not twist or pull by force ends of the optical cable. It can cause malfunction. Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to

the device before cleaning. Unplug the power cord when left unused for a long period of time. Information on disposal for scrapped devices: do not burn or mix with general

household waste, and please treat them as normal electrical wastes.




Contents 1. Introduction ................................................................................................................. 1

1.1 Introduction to CVHDSDI-6G ............................................................................. 1 1.2 Features ............................................................................................................ 1 1.3 Package List ...................................................................................................... 1

2. Specification ............................................................................................................... 2 3. Panel Description ........................................................................................................ 4

3.1 Front Panel ........................................................................................................ 4 3.2 Rear Panel ......................................................................................................... 4 3.3 Side Panel ......................................................................................................... 5 3.4 Top Panel ........................................................................................................... 5

4. System Connection ..................................................................................................... 7 4.1 Usage Precaution .............................................................................................. 7 4.2 System Diagram ................................................................................................ 7

5. Switches Operation ..................................................................................................... 8 5.1 Built-in EDID Invoking ........................................................................................ 8 5.2 Buttons Locking/Unlocking ................................................................................ 9 5.3 Audio Input Switching ........................................................................................ 9

6. Panel Drawing .......................................................................................................... 10 7. Troubleshooting & Maintenance ............................................................................... 11 8. Customer Service ..................................................................................................... 12




1. Introduction 1.1 Introduction to CVHDSDI-6G

Thanks for purchasing this CVHDSDI-6G 4K HDMI to 6G SDI converter! This converter is designed to convert 4K@30Hz 4:4:4 (max) HDMI video input to two 3840x2160@30Hz 4:2:2 (max) SDI outputs. It supports balanced L/R analog audio or ASE/EBU audio input to embed SDI video outputs, and these audio inputs volume can be selected to control via AUDIO button on top panel. The converter features 8-pin DIP switch to select built-in EDID for HDMI input, lock or unlock buttons, and choose HDMI embedded audio, external balanced analog audio or ASE/EBU audio as input source. 1.2 Features

HDMI input resolution is up to 4K@30Hz 4:4:4, and two SDI outputs resolution up to 3840x2160@30Hz.

SDI outputs support SD/HD/3G-SDI/6G-SDI. Supports balanced L/R analog audio or AES/EBU audio input. Supports firmware updating. DIP switch can be used for built-in EDID invoking, buttons locking or unlocking

and audio input switching. Fully compliant with the HDMI 1.4 and HDCP2.2 specifications.

1.3 Package List

1x CVHDSDI-6G HDMI to 6G SDI Converter 1x AC power adapter (12 VDC, 1A) 1x Plastic feet 1x User's manual

Note: Please contact your distributor immediately if any damage or defect in the components is found.




2. Specification Video

Input (1) HDMI

Input Connector (1) 19-pin type-A female HDMI

Output (2) SDI

Output Connector (2) BNC

HDMI Input Video Resolution

Up to 4K@30Hz 4:4:4;

SDI Outputs: Up to 4K@30Hz 4:2:2, support

SD/HD/3G-SDI/6G-SDI

SDI Outputs Video Resolution

The SDI resolution is switched based on HDMI

input, if HDMI input resolution is 1080p, the SDI

outputs is 1080p.

HDMI Standard HDMI1.4, HDCP2.2 compliant

EDID Management Built-in EDID

Audio

Input (1) L-ANALOG or AES/EBU; (1) R-ANALOG;

(1) Embedded HDMI Audio

Input Connector (2) TRS

Audio Input Impedance >10kΩ

Analog Audio Format PCM

Digital Audio Format AES/EBU

Embedded HDMI Audio Format PCM

Frequency Response 20 Hz to 20 kHz, ±3dB

Control

Control Part (1) 8-pin DIP Switch; (4) Black Buttons;

(1) Micro USB for Firmware Updating

General

Operation Temperature 0 ~ +40℃

Storage Temperature -10 ~ +55℃

Relative Humility 10%-90%

Maximum Power Consumption 11 watts




Input Power 12VDC 1A

AC Adapter Input Power 100 ~ 240 VAC, 50/60 Hz

Dimensions (W*H*D) 120mm x 30mm x 100mm

Net Weight 305g




3. Panel Description 3.1 Front Panel

① HDMI IN: HDMI® port for connecting the HDMI source device. ② AUDIO LED: The LED illuminates blue when external audio is selected as audio

input source. ③ L-ANALOG or AES/EBU: TRS audio socket for balanced left channel analog audio

or AES/EBU digital audio input. ④ R-ANALOG: TRS audio socket for balanced right channel analog audio input. 3.2 Rear Panel

① DC 12V: DC barrel connector for AC power adapter. ② POWER LED: The LED illuminates red when power is on. ③ SDI OUTPUTS: BNC connectors for connecting SDI video displays. ④ HDMI LED: The LED illuminates blue when this device detects HDMI input signal. ⑤ FW: Micro USB port for performing firmware updates.

1 2 3 4

1 2 3 4 5




3.3 Side Panel

① 8-pin DIP switch: 8 DIP switches for built-in EDID invoking, buttons locking or

unlocking and audio input switching. When in the down (1) position, the switch represents “ON”, while putting the switch in the up (0) position represents “OFF”.

Note: The DIP switches status and its corresponding setting can find at the chapter of Switches Operation.

3.4 Top Panel

→1

AES/EBULR

AUDIO

VOLUME

MUTE


1

2

3




① AUDIO: Press the button repeatedly to cycle select the input audio needed to be control. These three blue LEDs has four status:

AES/EBU L R Description

Status 1 ON OFF OFF Select the AES/EBU digital audio.

Status 2 OFF ON OFF Select the balanced left channel analog audio.

Status 3 OFF OFF ON Select the balanced right channel analog audio.

Status 4 OFF ON ON Simultaneously select the balanced left and right channel analog audio.

② VOLUME: Press the up or down direction button to increase or decrease the

selected input audio. ③ MUTE: Press this to mute or unmute all audio.




4. System Connection 4.1 Usage Precaution

Verify all components and accessories included before installation. System should be installed in a clean environment with proper temperature and

humidity. All of the power switches, plugs, sockets, and power cords should be insulated and

safe. All devices should be connected before power on. 4.2 System Diagram

DVD

SDI Displays

Audio Player

HDMI:SDI:

Audio:




5. Switches Operation The 8 DIP switches on side panel provide the following settings: The DIP switch status and its corresponding settings are shown at the back of product.

5.1 Built-in EDID Invoking

The Extended Display Identification Data (EDID) is used by the source device to match its video resolution with that of the connected display. Since displays with different capabilities can be connected to the converter, the EDID DIP switch 1 and 2 can be used to set the EDID information that is passed to the source devices.

Force to UHD (4K@30Hz 4:2:2) – Switch 1 to “ON”, Switch 2 to “OFF” If the HDMI source is capable of outputting 4K@30Hz 4:2:2, the converter will instruct

ONOFF

1 2 3 4 5 6 7 8

AES/EBU AUDIO

ANALOG AUDIO

INPUT AUDIO

HDMI AUDIO

LOCK

UNLOCKSELECT FORMAT

AUTO

UHD

ON

ON

OFF

OFF

1

1

2

2

HD

ONOFF

1 2

ONOFF

1 2

SELECT FORMAT

AUTO

UHD

ON

ON

OFF

OFF

1

1

2

2

HD

ONOFF

1 2




9

the source to output 4K@30Hz 4:2:2 video. Force to HD (1080I@30Hz) – Switch 1 to OFF, Switch 2 to “ON” If the HDMI source is capable of outputting 1080I@30Hz, the converter will instruct the source to output 1080I@30Hz video. AUTO – Switch 1 to “OFF”, Switch 2 to “OFF” The convert will automatically allocate an optimum resolution with current source equipment based on its output capabilities. 5.2 Buttons Locking/Unlocking

Switch 6- Lock/unlock buttons Put switch 6 in “ON” to lock buttons on top panel, or to “OFF” for unlocking. 5.3 Audio Input Switching

Switch 7- Embedded HDMI Audio – Input Audio Put switch 7 in “OFF” to select embedded HDMI audio, or to “ON” for external balanced analog or AES/EBU audio input. Switch 8- Analog Audio, AES/EBU Audio Before using switch 8, the switch 7 must be set to “ON”. Put switch 8 in “OFF” to select balanced analog audio, or to “ON” for digital AES/EBU audio input.

ONOFF

6

LOCK

UNLOCK

ONOFF

7 8

AES/EBU AUDIO

ANALOG AUDIO

INPUT AUDIO

HDMI AUDIO




10

6. Panel Drawing

→

DC 12V SDI OUT 1 SDI OUT 2

FW

AES/EBULR

AUDIO

VOLUME

MUTE

01

HDMI IN

ANALOG orAES/EBUL - R - ANALOG


ONOFF

1 2 3 4 5 6 7 8

AES/EBU AUDIO

ANALOG AUDIO

INPUT AUDIO

HDMI AUDIO

LOCK

UNLOCKSELECT FORMAT

AUTO

UHD

ON

ON

OFF

OFF

1

1

2

2

HD

ONOFF

1 2

120 mm

100

mm

30 m

m




11

7. Troubleshooting & Maintenance

Problems Potential Causes Solutions

Output image with snowflake.

Bad quality of the connecting cable.

Try another high-quality cable.

Fail or loose connection. Make sure the connection is good.

No output image when switching.

No signal at the input / output end.

Check with oscilloscope or multimeter if there is any signal at the input/ output end.

Fail or loose connection. Make sure the connection is good.

The product is broken. Send it to authorized dealer for repairing.

POWER indicator doesn’t work or no respond to any operation.

Fail connection of power cord.

Make sure the power cord connection is good.

Cannot control the device by buttons.

The front panel buttons are locked.

Put switch 6 in “OFF” to lock buttons.

If your problem still remaining after following the above troubleshooting steps, please find further assistance.




12

8. Customer ServiceThe return of a product to our Customer Service implies the full agreement of the terms and conditions hereinafter. There terms and conditions may be changed without prior notice.

1) WarrantyThe limited warranty period of the product is fixed three years.

2) ScopeThese terms and conditions of Customer Service apply to the customer serviceprovided for the products or any other items sold by authorized distributor only.

3) Warranty Exclusions: Warranty expiration. Factory applied serial number has been altered or removed from the product. Damage, deterioration or malfunction caused by: Normal wear and tear. Use of supplies or parts not meeting our specifications. No certificate or invoice as the proof of warranty. The product model showed on the warranty card does not match with the

model of the product for repairing or had been altered. Damage caused by force majeure. Servicing not authorized by distributor. Any other causes which does not relate to a product defect.

Shipping fees, installation or labor charges for installation or setup of the product.

4) Documentation:Customer Service will accept defective product(s) in the scope of warranty coverageat the sole condition that the defeat has been clearly defined, and upon reception ofthe documents or copy of invoice, indicating the date of purchase, the type ofproduct, the serial number, and the name of distributor.

Remarks: For further assistance or solutions, please contact your local distributor.


ALTIMIUM

587 Avenue Blaise Pascal

77550 MOISSY-CRAMAYEL

Tél : 01.64.13.31.00

Fax: 01.60.29.62.70

Mail: [email protected]

Web: www.altimium.com

Date post:	22-Aug-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

User Manual CVHDSDI-6G · Altimium HDMI to 6G SDI Converter . Preface . Read this user manual...

Documents