User ManUal

8001 / 8002 s2 / 9003 Premium s2 series Models

Issue 04/2013

Contents1 Components/Terminology................................. 4

2 Introduction............................................................. 5

3 KeytoSymbols....................................................... 53.1 Generalinstructions...............................................53.2 Safetyinstructions..................................................5

4 Generalhandlingoffirearms.......................... 64.1 Importantbasics....................................................64.2 Shooting...............................................................74.3 Maintenance.........................................................84.4 Transport...............................................................84.5 Storage.................................................................84.6 Hearingandeyeprotection....................................8

5 Generalhandlingofcompressedaircylinders.................................... 8

6 Safetyflag..............................................................10

7 Legal.........................................................................11

8 Intendeduse.........................................................11

9 Liability....................................................................11

10Beforeusingforthefirsttime........................12

11Soft-Link®(onlyModel9003Premium)..............12

12Removingthealuminiumstock (dependingonmodel).............................................1312.1 RemovingthealuminiumstockonMod.8002........1312.2 Removingtheactioncarrieron9003Precise.......1412.3 Removingtheactioncarrieron9003Premium.......14

13Cocking,loading,engaging/releasingthesafetycatch....................................................1513.1 Cocking..............................................................1513.2 Loading..............................................................1513.3 Engagingthesafetycatch.....................................1613.4 Releasingthesafetycatch.....................................16

14Convertingthecockinglever..........................1714.1 Conversionfromrighttoleft..................................17

15Trigger.....................................................................1815.1 Triggerweight.....................................................1915.2 Firststagepull(onlywithtwo-stagetrigger)...........1915.3 Searengagement................................................1915.4 Firststagetravel(onlywithtwo-stagetrigger)........1915.5 Triggerstop........................................................2015.6 Adjustingthetriggerblade..................................2015.7 Conversionfromtwo-stagetriggerto singlestagetrigger..............................................2015.8 Conversionfromsinglestagetriggerto two-stagetrigger................................................2015.9 Triggerfaultscausedbyincorrectadjustment.........2115.10Basictriggeradjustment......................................21

2

16Dryfiringdevice..................................................22

17Compressedaircylinder...................................22

17.1 Screwingthecompressedaircylinderin................2317.2 Releasingthecompressedaircylinder...................2317.3 Fillingthecompressedaircylinder........................23

18Cheekpiece...........................................................2418.1 Removingthecheekpiece...................................2418.2 Adjustingthecheekpiece...................................2418.2.1Settingthecheekpiece9003Precise...................25

19Buttplate.................................................................2519.1 Removingthebuttplate.......................................2519.2 Adjustingthebuttplate(model-dependent)...........2519.2.1Buttplateadjustment9003Precise.......................2619.3 Buttplateadjustmentoptions................................26

20Stockadjustment.................................................2720.1 Forend..............................................................2720.1.1Forendraiserblockadjustment4960..................2720.2 Gripadjustment.................................................2820.2.1Gripadjustment9003Precise.............................2820.2.2PRO-Gripequipment(model-dependent).............29

21Opticalsights/rearsight(option)...................2921.1 Mounting............................................................2921.2 Elevationandwindageadjustment........................2921.3 Zeroadjustment...................................................29

22Maintenance/cleaning.....................................3022.1 General .............................................................. 3022.2 Maintenance intervals .......................................... 3122.3 Trigger maintenance ............................................. 3222.4 Maintenance of the optical sights .......................... 32

23Troubleshooting...................................................32

24Technicaldata.......................................................32

25Disposal..................................................................33

26Miscellaneous.......................................................33

27ShootingPerformance.......................................34

28Guarantee..............................................................34

3

1 Components/Terminology

[1] Cheekpiece

[2] Rearsight

[3] Cockinglever

[4] Frontsight

[5] Barrelweight

[6] Compressedaircylinder

[7] Support

[8] Forendraiserblock

[9] Trigger

[10] Grip

[11] Barrelledactioncarrier

[12] Threadforweightcarrier

[13] Buttplate

[14] Airreleasescrew

[15] Refillingadapter

[16] Highsightblock

[17] Visiblemuzzle

[18] Barrelunit

4

Fig. 1 Overall view using 8002 with aluminium stock as example

Components/Terminology

[10] Grip

Fig. 1 Overall view using 8002 with aluminium stock as example

[1] [2] [3]

[17][5]

[6][7][8][9]

[10][11]

[14] [15]

[13]

[12]

[16] [4][18]

2 Introduction

DearANSCHÜTZCustomer,

ThankyouforchoosinganANSCHÜTZproduct.Manyspectacularsportingsuccesseshavebeenachievedbymarksmen,olympiansandshootersinworldandEuropeanchampionshipsusingANSCHÜTZsportingrifles.ANSCHÜTZhuntingandsportingriflesarehighlyreputedasaresultoftheirwell-engineereddesign,workmanshipandoutstandingshootingperformance.Qualityandprecisionareapartofourtradition,andhavegrownasaresultofourexperiencesince1856.

WewishyoumuchpleasureandsportingsuccesswithyournewANSCHÜTZproduct.

YourANSCHÜTZteam

3 KeytoSymbols

Inthishandbook,thefollowingsymbolsareusedtodistinguishbetweengeneralinformationandparticularlyimportantinformation:

3.1 GeneralinstructionsX isthesymbolforaninstruction

9 showsthedesiredresult

y isthesymbolforalistitem

) isthesymbolforapossiblehandlingconsequence

3.2 Safetyinstructions$$ identifies$a$safety$instruction

An.instruction.indicating.a.specific.course.of.action.

NOTe!

Indicates.a.hazardous.situation.that.can.lead.to..minor.physical.injury.or.material.damage.

CauTION!

Indicates.a.hazardous.situation.that.can.lead.to..serious.physical.injury.or.death.

WaRNING!

5

4 Generalhandlingoffirearms

Firearmsaredangerousobjectsrequiringtheutmostcareintheirstorageanduse.Thefollowingsafetyandwarninginstructionsmustbeobservedwithoutexception!

The.firearms.legislation.of.the.relevant.country.must.be.respected.and.complied.with.

NOTe!

4.1 Importantbasics

The.use.of.firearms.while.under.the.influence.of.drugs,.alcohol.or.medication.is.not.permitted.Vision,.dexterity.and.judgement.can.all.be.adversely.affected.A.good.physical.and.mental.constitution.is.a..prerequisite.for.using.a.firearm.

NOTe!

$$ A$firearm$must$only$ever$be$used$for$its$designated$purpose.$$ Firearms$owners$are$responsible$for$ensuring$that$their$firearm$is$at$no$time,$and$$

especially$when$absent,$within$reach$of$or$accessible$to$children$or$other$unauthorised$persons.

$$ Firearms$must$not$be$handed$over$to$unauthorised$persons.$$ Modifications$to$the$rifle$and$the$use$of$non-genuine$ANSCHÜTZ$accessories$can$lead$$

to$malfunctions.$$ Serious$or$life-threatening$injuries$and$damage$can$be$caused$by$the$use$of$incorrect$$

ammunition,$by$contamination$in$the$barrel$or$by$incorrect$cylinder$components.$$ Weapons$modified$in$a$way$that$could$affect$safety$must$not$be$used.$If$a$fault$or$$

malfunction$is$detected,$the$weapon$must$be$unloaded$and$taken$to$an$authorised$$gunsmith$for$repair.

$$ In$the$event$of$external$effects$(e.g.$corrosion,$being$dropped,$etc.),$the$weapon$must$$be$checked$by$an$authorised$gunsmith.

$$ A$weapon$must$always$be$treated$with$the$utmost$care$and$be$protected$from$accidental$damage.

6

4.2 Shooting

Danger.to.life.and.causing.material.damage!

Aimingtherifleatpeopleandobjects.h Whentherifleisnotinuse,keepthemuzzle

pointinginasafedirection.h Themuzzleofafirearmmustneverbeheld

inadirectionwhereitcancancausedamageorendangerlife.

WaRNING!

Malfunction.when.shooting!

Shotnotdischargedaftertriggerpulled.h Donotlookdownintothemuzzle.h Keepthemuzzleofthefirearmpointing

inasafedirection.h Unloadthefirearm.h Removeresiduesfromthebarrel.

WaRNING!

$$ Any$firearm$must$be$treated$as$if$it$were$loaded.$$ Never$pick$up$a$firearm$by$the$trigger.$$ Shooting$galleries$must$be$adequately$ventilated.$$ Any$bullet$trap$in$the$shooting$gallery$must$be$completely$safe$and$visible.$$ No$persons$may$stand$in$the$vicinity$of$the$target$during$a$shoot.$$ Firearms$should$not$be$used$when$visibility$is$poor.$$ Do$not$shoot$into$the$air,$at$hard$or$smooth$surfaces,$at$water$or$at$targets$on$the$horizon.$$ Do$not$shoot$at$targets$if$the$shot$could$ricochet$or$be$deflected$in$a$dangerous$manner.$$ To$prevent$accidents$or$damage$to$your$rifle,$never$discharge$a$shot$with$the$muzzle$held$

under$water$or$up$against$materials$or$objects.$$$ Only$shoot$using$the$calibre$specified$on$the$barrel$of$the$rifle.$$ Only$new,$clean,$factory-charged$ammunition$of$the$calibre$permitted$for$the$rifle$$

may$be$used.$$ The$ammunition$must$conform$to$the$specifications$of$the$C.I.P.$$ Only$ever$load$the$rifle$immediately$before$use.$$ Life-threatening$injuries$and$material$damage$can$be$caused$by$the$use$of$incorrect$$

ammunition,$contamination$in$the$barrel$or$incorrect$cylinder$components.$$ Only$genuine$ANSCHÜTZ$parts$may$be$used.

7

4.3 Maintenance$$ Ensure$that$the$rifle$is$unloaded$before$and$after$use$or$during$maintenance$and$cleaning.4.4 Transport

$$ Firearms$may$only$be$transported$in$an$unloaded$condition$and$in$locked$containers.$$$ When$you$are$putting$your$rifle$in$a$case$or$a$soft$case,$always$make$sure$that$the$rifle$

and$the$inside$of$the$case$or$soft$case$are$dry$and$that$no$water$or$moisture$remains.$$ Only$ever$put$a$cleaned,$dry$and$oiled$rifle$in$your$case$or$soft$case.$$ Always$place$the$rifle$in$the$transport$case$with$the$sight$facing$upwards$$

(towards$the$handle).$This$protects$the$rear$sight$from$impacts$and$also$protects$$the$rear$sight$setting$screws$as$a$result.4.5 Storage

$$ Firearms$that$are$not$in$use$must$be$kept$in$a$secure$place$under$lock$and$key.$$ Firearms$must$always$be$stored$in$an$unloaded$and$uncocked$condition.$$ Ammunition$must$be$kept$in$a$separate$place$under$lock$and$key.4.6 Hearingandeyeprotection

For.your.own.safety,.approved.hearing.and.eye..protection.should.be.used.when.shooting!Shooting.without.safety.equipment.can.result.in..da-mage.to.your.hearing.and.sight.

NOTe!

5 Generalhandlingofcompressedaircylinders

When.using.compressed.air.cartridges.please..always.observe.the.manufacturer's.instructions!

NOTe!

$$ The$fill$level$indicator$of$the$compressed$air$cylinder$may$only$be$checked$when$the$compressed$air$rifle$is$unloaded$and$uncocked.

$$ The$fill$level$indicator$of$the$compressed$air$cylinder$must$not$be$checked$during$re-filling.

Design.aspects.mean.that.the.fill.level.indicator..operates.with.an.accuracy.of.±.10%..Temperature.influences.mean.that.there.can.also.be.deviations..in.the.fill.level.indicator.

NOTe!

$$ Full$compressed$air$cylinders$must$not$be$exposed$to$temperatures$below$-20°C$or$$above$70°C$(when$transporting$and$storing$them,$adequate$insulation$must$be$provided,$$e.g.$by$storing$in$expanded$polystyrene$packaging$or$in$a$gun$case).

$$ In$aircraft,$when$sending$by$post,$etc.$the$compressed$air$cylinders$must$always$$be$unfilled.

$$ After$approx.$20$fillings,$the$compressed$air$cylinder$must$be$emptied$slowly$and$$completely$in$order$to$allow$any$condensed$water$to$escape.

$$ When$screwing$on$or$off$the$compressed$air$cylinder$or$when$refilling$it,$always$stand$side$on$in$relation$to$the$cylinder$and$ensure$that$no$other$person$is$in$the$vicinity$of$the$end$of$the$cylinder$(where$the$manometer$is$positioned).

8

ANSCHÜTZ.recommends.the.use.of.an.air.release.screw.from.the.ANSCHÜTZ.range.of.accessories..(Item.No.:.001520).for.emptying.the.compressed.air.cylinder.

NOTe!

$$ The$compressed$air$cylinder$must$be$checked$for$cracks$and$damage$before$each$use.$$ Compressed$air$cylinders$which$have$leaks$or$which$are$damaged$must$be$emptied$safely$

and$must$not$be$used$or$filled$again.$$ Compressed$air$cylinders$must$not$be$used$for$longer$than$10$years.$$ After$10$years$(from$the$date$of$manufacture)$the$compressed$air$cylinders$must$be$safely$

emptied$in$accordance$with$the$manual$(see$Chapter$17)$and$must$not$be$used$or$filled$any$more$(the$date$of$manufacture$is$marked$on$the$compressed$air$cylinder).

$$ The$surface$of$the$compressed$air$cylinder$must$not$be$tampered$with.$$ In$particular,$you$must$not$carry$out$any$engraving$or$other$abrasive$processes$because$

this$could$lead$to$damage$to$the$pressurised$container$and$thus$present$a$safety$hazard.$$ Compressed$air$cylinders$and$the$refilling$adapter$must$be$stored$in$a$secure,$dry,$$

grease-free$and$dust-free$location.

The.refilling.adapter.is.also.fitted.with.an.air.filter..to.protect.from.dirt.and.dust.particles.

NOTe!

$$ After$unscrewing$the$compressed$air$cylinder,$the$cylinder$thread$must$be$kept$clean$$and$the$relevant$protective$cap$must$be$fitted.

Self.monitoring!The.marksman.is.responsible.for.compliance.with.the.regulations.and.stipulations.contained.in.the.ANSCHÜTZ.user's.handbook.ANSCHÜTZ.accepts.no.liability.for.damage.of.any.kind.caused.by.modification.of.parts,.conversion..or.fitting.of.non-genuine.ANSCHÜTZ.parts.or.by.non-compliance.with.the.user's.manual.

NOTe!

Danger.of.explosion!

Explosiondangerfromoiledairentryvalveandthread.

h TheairentryvalveandthreadonthecompressedaircylindershouldonlybelightlygreasedusinggenuineANSCHÜTZgrease(specialgrease4425,ItemNo.:001489).

WaRNING!

9

Please.use.only.genuine.ANSCHÜTZ.compressed..air.cylinders.(max..200.bar)!.If.you.use.non-genuine.ANSCHÜTZ.compressed..air.cylinders,.the.liability.and.guarantee.entitlement.for.the.compressed.air.cylinder.and.the.rifle.will.become.void.

NOTe!

$$ The$maximum$filling$pressure$for$compressed$air$cylinders$is$200$bar$at$room$temperature.

Danger.of.explosion!

Overfilledcompressedaircylinder.h Themaximumfillingpressureof200baratroom

temperaturemustnotbeexceeded.

WaRNING!

$$ When$filling$the$compressed$air$cylinder,$the$compressed$air$must$not$contain$oil,$water$$or$any$other$contaminant$(DIN$EN$12021$-$breathing$air).

$$ ANSCHÜTZ$supplies$compressed$air$cylinders$unfilled,$in$accordance$with$the$safety$$regulations.

$$ ANSCHÜTZ$recommends$that$compressed$air$cylinders$be$always$transported$empty.$$ Compressed$air$cylinders$must$never$be$opened$or$modified$mechanically$by$$

non-authorised$specialists.$$ The$compressed$air$cylinder$must$be$protected$from$forceful$impacts.$$ Compressed$air$cylinders$are$not$intended$for$the$transport$of$gases$of$any$kind.

When.filling,.transporting.and.handling..(including.for.commercial.use).you.must.follow..the.“Compressed.Gases.Technical.Regulations.(TRG).or.the.legal.stipulations.applicable.in.the.individual.country.concerned.

NOTe!

6 Safetyflag

Malfunction.and.missing.action.pressure!

Bentloadingmechanismcausedbyincorrecthandling.h Neverclosetheactionifthesafetyflagisinserted.

CauTION!

10

7 Legal

The.applicable.firearms.legislation,.regulations.and.provisions.for.the.relevant.country,.and.also.the.safety.rules.of.the.hunting.and.sporting.organisations.must.be.observed.

NOTe!

8 Intendeduse

TheANSCHÜTZcompressedair8001,8002and9003Premiumarecompressedairrifles.Theyareexclusivelyforuseonranges(forsportsdisciplines)andmustbeusedexclusivelybypersonswiththerelevantfirearmspermit.

Theuseissubjectexclusivelytothe"GeneralTechnicalRegulations“forallshootingsportsdisciplinesoftheINTERNATIONALSHOOTINGSPORTFEDERATION(ISSF),Bavariaring21,80336München,GermanyortheregulationsoftheINTERNATIONALBIATHLONUNION,Peregrinstrasse14,A-5020Salzburg,Austria,E-Mail:biathlon@ibu.at.

A.firearm.must.only.ever.be.used.for.its.designated.purpose.

NOTe!

11

9 Liability

ansCHÜTZwillacceptnoliabilityorclaimsforcompensationfordamageofanykindarisingfrom:

y failuretocomplywiththeinstructionsinthisuser'shandbook,y impropertreatmentorrepair,y useofnon-genuineANSCHÜTZparts,y incorrecthandlingorcare,y negligence,y removalofthesealinglacquer,y unauthorisedtamperingory transportdamage.

Modifications.to.or.tampering.with.the.rifle.or.its.parts.are.forbidden.and.may.possibly.infringe..the.guarantee.conditions..Alterations.of.this.kind.can.have.an.adverse.effect..on.the.safe.use.of.the.product.and.lead.to.accidents.that.endanger.life.and.limb..In.such.cases.the..guarantee.is.automatically.void.

CauTION!

$$ The$rifle$must$be$examined$for$any$changes$each$time$before$use.$

10Beforeusingforthefirsttime

For.safety.reasons,.check.the.action.fixing.each.time.before.you.shoot.

NOTe!

X Wipeoffanyexcessoilfromthesurfaceofthebarrelledaction.

X Cleaningcordwithcottonwicks(CleaningKit507,ItemNo.:001491)tobepulledthroughthebarrelfromthechambertowardsthemuzzle.

11Soft-Link®(Model9003Premiumonly)

TheairrifleandtheactioncarrierareconnectedtogetherwiththeSoft-Link®connectionsystem.Thisactionfixinghasavibration-dampingfixedmount(intheareaoftheactionhousing)andavibration-dampingfreemount(onthesupport).

Tensionsthatarecreatedasaresultofdifferentmaterialsinairrifleactionsandactioncarriers,andtheirdifferentcoefficientsofthermalexpansion,arethuseliminated(tension-compensatingthermalexpansionjoint).

TheintegratedSoft-Link®vibrationdampersalsode-coupletheairrifleactionandtheactioncarrier.Theoscillationsandvibrationcreatedintheairrifleactionareeffectivelyabsorbedandcannotbefeltinthealuminiumstockbythemarksman.

TheairgunisdeliveredwithhardSoft-Link®vibrationdamping.ThescopeofdeliveryincludessoftSoft-Link®vibrationdamping.

Changingthevibrationdampingiscarriedoutasfollows:X Releasescrews[1]onbothsides.

X Releasethesetscrews[2]onbothsides(approx.4turns).

X Pullthesupport[3]offtheactioncarriertowardsthemuzzle.

X Removetheaction[4]fromtheactioncarrier[5].

Fixingtothebarrelledactioncarrier:X Insertorreplacetheround(hardorsoft)Soft-Link®elements[C]

onbothsides.

12

Fixingtothesupport:X Insertorreplacethelong(hardorsoft)Soft-Link®elements[A]

onbothsides(2innumber).

X Fittingtheactioniscarriedoutinreverseorder.

When.using.the.soft.Soft-Link®.elements,.before.fitting.the.screws,.the.flanged.bushes.[B].must.be.fitted.from.the.outside.into.the.Soft-Link®.chamber.at.position.[1]..Then.the.screws.must.be.fitted.and.tightened.on.both.sides.at.position.[1].

NOTe!

[4]

[C]

[1] [5]

[3]

[2]

[C]

[B]

[B]

[A]

[A]

Fig. 2 Soft-Link®

12Removingthealuminiumstock(model-dependent)12.1 Removingthealuminiumstockonmodel8002

X Removethecompressedaircylinder(seeChapter17.2).

X Removethescrews[a]ontheendofthesupport[5].

X Releasethescrews[b]onthesupportfixing.

X Removethebeddingscrews[c]ontheforend[6].

X Removetheforend[6].

X Removethebeddingscrew[d]inthealuminiumstock(infrontofthetrigger).

X Pullthesupport[5]fromthealuminiumstockuntilthemechanicalconnectionreleases.

X Removealuminiumstockfromaction(thevibration-absorbingelastomerintheactionbedisnowloose).

X Fittingiscarriedoutinthereversesequence.

[c] [c]

[a]

[d]

[b]

[5]

[6]

Fig. 3 Removing the aluminium stock

13

12.2 Removingtheactioncarrieron Model9003Precise

X Removethecompressedaircylinder(seeChapter17.2).

X Removethescrews[3a]and[3b]ontheendofthesupportandremovetheuppersectionofthesupport.

X Releasethescrews[1a]and[1b]attheside,thenremovetheactioncarrier.

Fittingtheactioncarrier(forthefirsttime)

X Placetheactioncarrierinpositionontheaction.

X Tightenthescrews[1a]and[1b]atthesideoftheactioncarrier.

X Screwthecompressedaircylinderin

X Tightenthescrews[2a]and[2b],ensuringtheclampingpieceisnotundertension.

X Tightenthescrews[3a]and[3b]afterfittingthesupport.

X Makesurethatthescrewsaretight.

[2][3]

[3]

[2]

Fig. 3a Removing the action carrier

[1a]/[1b] [2a]/[2b]

[3a]/[3b]

Fig. 3b Model 9003 Precise

12.3 Removingtheactioncarrieron Model9003Premium

X Removethecompressedaircylinder(seeChapter17.2).

X Releasescrews[1a],[1b],[2a]and[2b].

X Slidethesupport[3]towardsthemuzzle.

X Removeactioncarrier[5]fromaction[4].

Fittingtheactioncarrier

X Fittingiscarriedoutinthereversesequence.

[1a]/[1b] [2a]/[2b][4]

[3][5]

Fig. 3c Model 9003 Premium

14

13Cocking,loading,settingthesafety,releasing13.1 Cocking

X Tocockthecockingpiston,pullthecockinglever[2]slowly(inthedirectionshownbythearrow)untilitreachesadetectablestop.

[2]

Fig. 4 Cocking the rifle

9 Theactionopensandtheopeningtothebarrelisrevealed.

13.2 Loading

Malfunction.and.danger.of.injury!

Useofnon-permittedammunitionandforeignobjects.h Useonlythecalibrepermittedforusewiththe

firearm.

CauTION!

X Toload,slidetheleadDiabolo(withtheflatend[A]facingforwards)intothechamberuntilitisflush.

X Locktheactionbyslowlyclosingthecockinglever[2].

9 Theactionislocked.

9 Therifleisnowreadytoshoot(loadedandcocked)(providedthatthecompressedaircylinderisfull).

Fig. 5 Diabolo (shown enlarged)

$$ Unloading$is$carried$out$by$shooting$a$pellet$into$the$bullet$trap.

15

[A]

13.3 engagingthesafetycatchX Pushthesafetycatch[x]inbackwards(inthedirectionofthearrow,

towards"S").

The.safety.catch.must.engage.exactly.and.audibly.and.must.not.sit.between.the.end.stops.The.firearm.can.only.be.engaged/released.when..the.rifle.is.cocked.

NOTe!

[x]

Fig.6 Safety catch "Safe"

9 Therifleiscockedandthesafetycatchisengaged.

13.4 ReleasingthesafetycatchX Pushthesafetycatch[x]inforwards(inthedirectionofthearrow,

towards"F").

The.safety.catch.must.engage.exactly.and.audibly.and.must.not.sit.between.the.end.stops.The.firearm.can.only.be.engaged/released.when..the.rifle.is.cocked.

NOTe!

[x]

Fig.7 Safety catch "Ready to Fire"

9 Therifleiscockedandthesafetycatchisreleased.

16

Attention!After.actuating.the.trigger.in.the.safe.condition.(dry.firing),.the.firearm.must.be.re-cocked.to.release.it.Forcible.changeover.of.the.safety.can.lead.to..damage.and.inadvertent.discharge.of.a.shot.

CauTION! 14Convertingthecockinglever14.1 Conversionfromrighttoleft

X Removecirclip[a]fromthepin[b].

X Removepin[b].

X Releasesetscrews[c].

X Removethecompletecockingleverassembly[d]andre-fitontheoppositesideinreverseorder.

[2]

[a]

[b][c]

[d]

Fig. 8 Converting the cocking lever [2]

17

15Trigger

[T]

[6]

[L] [5]

[1]

[1]

[2]

[3]

[4]

[7]

Fig. 9 Trigger (side view)

[8]

Fig. 10 Trigger (view from below)

Key(toFigs.9+10)

1 Tension spring

2 Catch link

3 Viewing window

4 Release catch

5 Trigger housing

6 Trigger blade

7 Trigger sear

8 Trigger sear clamping screw

F1 Weight of first stage

F2 Trigger weight

T Trigger stop

L First stage travel

C Basic factory setting/sealed

Danger.to.life!

Dangertolifefromloadedfirearm.h Makesurethattherifleisunloadedwhencarrying

outalignmentandadjustmentprocedures.

WaRNING!

The.trigger.on.Model.5065.is.delivered.with..the.following.factory.setting:.Two-stage.trigger.with.approx..100.g.set.trigger.weight.

NOTe!

18

The.setting.screws.B.and.C.are.pre-set.and.sealed.in.the.factory..Setting.or.modification.using.these.screws.is.prohibited.

NOTe!

15.1 Triggerweight

SettingthetriggerweightusingthesettingscrewF2(settingrangefrom50gto170g):y turnclockwise=triggerweightisincreased(+)y turnanticlockwise=triggerweightisreduced(–)

15.2 Firststagepull(onlywithtwo-stagetrigger)

SettingthefirststagepullusingthesettingscrewF1:y turnclockwise=firststageweightisincreased(+)y turnanticlockwise=firststageweightisreduced(–)

15.3 Searengagement

Thesearengagementdenotesthetravelfromthesecondstagetothereleaseofthetrigger.Thesearengagementissetinthefactorytoanoptimumvalue.

Danger.to.life!

Unintentionaldischargeasaresultoftooshortasearengagementand/ortoolowatriggerweight.

h Donotsetthesearengagementtooshort.h Donotsetthetriggerweighttoolow.h Donotsubjectloadedandunsecuredriflesto

impactanddonotuseforcetoclosethebreech.

WaRNING!

15.4 Firststagetravel(onlywithtwo-stagetrigger)

Firststagetraveldenotesthetravelofthetriggerbladefromthezeropositiontothesecondstage.

Settingthefirststagetravelusingsettingscrew[L]:y turnclockwise=firststagetravelisshortenedy turnanticlockwise=firststagetravelislengthened

19

15.5 Triggerstop

Thetriggerstopdenotesthetravelfromthesecondstagetotheendstopforthetriggerblade.

Settingthetriggerstopusingthetriggerstopsettingscrew[T]:y turnclockwise=triggerstopisshortenedy turnanticlockwise=triggerstopislengthened

Malfunction!

Triggerstopsettingscrewisscrewedinbeyondthesecondstageordirectfunction(triggerwillnotactuate).

h Triggerstopadjustmentscrewshouldnotbescrewedinbeyondthesecondstageordirectfunction.

CauTION!

15.6 adjustingthetriggerblade

Releasetherelevantclampingscrew(accordingtorequiredsetting).Thetriggerbladecanbemovedalongtheguide,swungtothesideandadjustedinheight.Thetriggerbladecanberemovedcompletelyandturnedthrough180°.Thelongerpartofthetriggerbladenowpointsdownwards.Thebladeholderisasymmetricandcanbefittedoffsetby180°toprovideadditionallengthadjustment.Thelateralbladeadjustmentcanalsobevariedinthesameway.Byreleasingthescrew(8),thetriggersearcanbeturnedthrough180°topermitoffsettotheside.

15.7 Conversionfromtwo-stagetriggertosingle stagetrigger

Adjustmentusingsettingscrew[L].Turnthesettingscrew[L]totherightuntilthereisnomorefirststagetravel.

Danger.of.injury.by.automatic.firing!

Automaticfiringandmalfunctioncausedbyminimumsettingoftriggerweight,firststagetraveltoosmallorthesearengagementistoosmall.

h Donotsetthetriggerweighttoolow.h Donotsetthefirststagetravelandsear

engagementtoosmall.

WaRNING!

15.8 Conversionfromsinglestagetriggerto two-stagetrigger

Adjustmentusingsettingscrew[L].Turnthesettingscrew[L]totheleftuntilthedesiredfirststagetravelisreached.

20

15.9 Triggerfaultscausedbyincorrectadjustment

Thetriggercatchesthecockingpistonorthefiringpin,butdoesnotshootwhenthetriggerisactuated:

X Makesurethatthesafetycatchisreleased.

) Ifthetriggerstopsettingscrew[T]isscrewedintoofarbyafewturns:

X Screwthetriggerstopsettingscrew[T]totheleftbyafewturnsuntilthecockingpistonorthefiringpinactuatesagainwhenthetriggerisactuated.

Thetriggerdoesnotcatchthecockingpistonorfiringpin:

Thesettingscrew[L](firststage)isscrewedintoofarbyafewturns.X Screwthesettingscrew[L]totheleftbyafewturns,untilthetrigger

catchesthecockingleverorthefiringpinagain.

X Thensetthedesiredfirststagetravel.

X Checkthatthetensionspring[1]isundamagedandishookedincorrectly.

Settingscrew[C],searengagement,hasbeenturned:X Turnthesettingscrew[C]byapprox.1turntotheleft.

X Cocktheweapon,turnthescrew[C]totherightuntiltheweapondischarges.Thenturnbackby1/5ofaturn.

The.trigger.function.must.be.checked.after.every.change..When.the.fault.is.eliminated,.check.the..desired.trigger.values.and.reset.them.if.necessary.

NOTe!

15.10Basicadjustmentofthetrigger

This.procedure.is.used.to.reset.all.settings.on.the.trigger..With.this.starting.setting,.the.trigger.can.then.be.individually.adjusted.again.

NOTe!

X Removetheactionfromthestock.

X Settheadjustingscrew[T]sothattheheadofthescrewisflushwiththetriggerhousingsurface[5].

X Settheadjustingscrew[L]sothatthetriggersear[7]ishorizontal.

X Cocktheaction.

X Setthetriggerusingtherelevantadjustmentscrewstogivetheindividualsettingsdesired.

21

16Dryfiringdevice

Thesafetycatchcanalsobeusedasadryfiringdevice.X Openthecockingleverandswingitslowlytotherearuntil

astopisfelt.

X Pushthesafetycatchinto"S".

9 Dryfiringdeviceisactive.

X Closethecockinglever.

X Releasethetrigger.

The.safety/dry.firing.device.can.only.be.actuated.when.the.airgun.is.cocked.

NOTe!

17Compressedaircylinder

Thecompressedairrifleisfittedwithanexchangeablecompressedaircylinder[4].Thecompressedaircylinder[4]canbeexchangedinboththefullandemptycondition.Ondelivery,thecompressedaircylinder[4]isnotscrewedintightly.Youshouldalwaysusethecoveringcaptoprotectthethreadonthecompressedaircylinder[4]fromdustanddamage.

Only.genuine.ANSCHÜTZ.compressed.air.cylinders.(max..200.bar).may.be.used!

CauTION!

Repairs.to.compressed.air.cylinders.may.only.be.carried.out.by.the.manufacturer.using.genuine..replacement.parts.If.this.is.not.observed,.the.liability.and.guarantee.become.void.

NOTe!

17.1 ScrewingthecompressedaircylinderinX Fillthecompressedaircylinderbeforeusing.

X Screwthecompressedaircylinderslowlyandcarefully,hand-tight,intothethreadonthesub-assemblycarrier(toavoiddamage).

$$ A$perceptible$resistance$is$felt$shortly$before$the$stop,$and$the$valve$opens$automatically.

22

17.3 Fillingthecompressedaircylinder

Only.refilling.bottles.with.a.maximum.pressure.of.200.bar.may.be.used!.Only.oil-.and.water-free.compressed.air.may.be.used.(DIN.EN.12021)!.

Filling.of.the.compressed.air.cylinders.may.only.be.carried.out.using.the.genuine.ANSCHÜTZ.refilling.adapter.(Item.No.:.001521)!.ANSCHÜTZ.recommends.the.use.of.diving.bottles.for.refilling.the.compressed.air.cylinders....When.screwing.on.or.off.the.compressed.air.cylinder.or.when.refilling.it,.always.stand.side.on.in.relation.to.the.cylinder.and.ensure.that.no.other.person.is.in.the.vicinity.of.the.end.of.the.cylinder.(where.the.manometer.is.positioned).

WaRNING!

A.complete.fill.(max..200.bar).is.adequate.for.approx..200.shots.(residual.pressure.approx..65.bar).*

Compressed.air.bottles.can.be.obtained.from..firearms.dealers..Refilling.of.compressed.air..bottles.can.also.be.carried.out.at.firearms.dealers..or.in.special.stores.for.diving.equipment.

*Not.applicable.with.Junior.cylinder.

NOTe!

X Checkallcomponentsthatareassociatedwiththefillingprocedure(refillingbottle,refillingadapter,compressedaircylinder)fordamage.

X Screwtherefillingadapterontotherefillingbottle.

X Screwthecompressedaircylinderin,hand-tight,byapprox.onemoreturnsothatitreststightlyagainstthestop.

17.2 Releasingthecompressedaircylinder

ANSCHÜTZ.recommends.that.the.compressed.air..cy-linders.always.be.released.when.the.compressed.air.rifle.is.not.being.used.to.protect.the.housing,.valve,.seals,.springs.and.for.safety.reasons..(no.readiness.to.fire.if.there.is.no.compressed.air).

NOTe!

X Unscrewthecompressedaircylinderbyapprox.justoneturn.Turnonlysofarthatnoaircomesout.

X Cocktherifle(seeChapter12.1)andreleasethetrigger.Repeattheprocedure3times(toallowanyremainingairtoescape).

) ThecompressedaircylindercanthenbeunscrewedwithnopressureontheO-ring.

Material.damage!

DamagetotheO-ringiftheairpressureistoohigh.h Neverunscrewthecompressedaircylindersofar

thatthecompressedaircanbeheardcomingout.

CauTION!

23

X Screwthecompressedaircylindercompletelyontotherefillingadapter.

X Tightentheknurledscrewontherefillingadaptersothatnoaircanescape.

X Openthebottlevalveveryslowlyuntilyoucannolongerhearaflowingnoise.

X Closetherefillingbottlevalveagainafterapprox.5secondsfillingtime(thecompressedaircylinderwillheatupslightly).

X Venttherefillingadapterbyreleasingtheknurledscrew.

X Screwtheknurledscrewontherefillingadapterbackin.

X Unscrewthecompressedaircylinderandscrewitintotheriflebyhand.

In.the.trade,.compressed.air.bottles.with.a..permissible.fill.pressure.of.300.bar.are.available,.and.these.have.the.same.filling.spigot.thread.as.compressed.air.bottles.having.a.fill.pressure.of..200.bar!

If.you.use.a.compressed.air.bottle.with.300.bar.to.fill.the.200.bar.compressed.air.cylinder,.you.must.use.a.pressure.reducer.set.to.200.bar!

It.is.not.permissible.to.fill.the.compressed.air..cylinder.to.over.the.quoted.maximum.pressure!The.regulations.and.rules.for.filling.the.compressed.air.cylinder.must.be.observed!

WaRNING!

18Cheekpiece18.1 Removingthecheekpiece

X Releasetheclampingscrew[a].

X Removethecheekpiece[1]fromtheholder.

X Fitinreverseorder.

18.2 adjustingthecheekpiece

Thecheekpiececanbetiltedtovariouspositions.Theknurledscrewsandthefixingscrews[c]and[d]mustbereleasedforsettingthevariouspositions.

X Releasetheclampingscrew[a].

X Releasethesettingscrew[c]forthedesiredinclinationposition.

X Inclinethecheekpiece[1]andthenretightenthesettingscrew[c]againhand-tight.

X Theheightofthecheekpieceisadjustedusingtheknurledscrew[d].

X Retightentheclampingscrew[a]handtight.

[d][b] [a][c]

[1]

Fig. 11 Removing/adjusting the cheek piece

24

18.2.1Settingthecheekpieceonthe9003Precise

X Coarsecheekpieceadjustmentiscarriedoutbyactuatingtherotaryknob[D1].

X Fineadjustmentoftheheightofthecheekpieceiscarriedoutusingthesettingwheel[G1].

X Axialdisplacementofthecheekpieceiscarriedoutbyactuatingthescrews[H1]and[J1].Thescrewscanonlybereleasedandtightenedusingascrewdriver.

X Thehorizontalangleofthecheekpiececanbeadjustedtosuitbyactuatingtherotaryknobs[E1]and[F1].

[H1]

[E1]

[D1]

[G1]

[F1]

[J1]

Fig. 11a Cheek piece adjustment possibilities on Model 9003 Precise

19Buttplate19.1 Removingthebuttplate

X Releasetheclampingscrew[a].

X Removethebuttplate[13]fromtheholder.

X Fitinreverseorder.

19.2 adjustingthebuttplate(model-dependent)

Thebuttplate[13]offersvariousdifferentsettingoptions.Theclampingscrewsmustbereleasedforsettingthevariousdifferentoptions.

X Releaseclampingscrews[a]and[c].

X Turntheknurlednut[d]untilthedesiredinclinationandlengtharereached.

X Retightentheclampingscrews[a]and[c]againhand-tight.

[a][d]

[13]

[c]

Fig. 12 Removing/adjusting the buttplate

25

19.2.1Buttplateadjustmentonthe9003Precise

X Forlengthadjustment,releasetheclampingscrew[C1]byhandinacounter-clockwisedirectionuntiltheclampingpiecelocatedunderneathrevealstheclampingrings[1]and[2].

X Settheclampingringstothedesireddistance.

X Toadjusttheangleofthebuttplate,releasethescrews[h]and[i]additionally.

X Afterfineadjustment,thefrontoneoftheclampingrings[1]and[2]shouldbeenclosedbytheclampingpiece.

X Theclampingscrew[C1]shouldbeclosedbyturningintheclockwisedirectionhand-tight.

X Thescrews[h]and[i]mustbetightened.

[h] [1]

[i] [2] [C1]

Fig. 12a Buttplate adjustment on the 9003 Precise

19.3 Buttplateadjustmentoptions

Thebuttplatecanbesetinmanydifferentways(dependingonthemodel).

[z]

[z][y]

[x]

Fig. 13 Buttplate adjustment options (shown for the Type 4759 aluminium buttplate)

Key(toFig.13)

[x] Clamping screw for upper plate wing

[y] Clamping screw for height adjustment and swing movement of the buttplate

[z] Clamping screws for lateral displacement (changing the buttplate fixing)

26

20Stockadjustment20.1 Forend

Theforend[6]canbeadjustedinthefollowingareas:y Elevation:

Theforendcanbeadjustedinheightusingpackingwashers.Longerscrewsmayberequired.

y Lengthadjustment:Theforendcanbemovedinfinitelyvariablyonthesliderail.

[6]

Fig. 14 Forend

20.1.1Forendraiserblockadjustment4860(9003and9003Precise)

X Releasethescrews[e]and[f]foraxialdisplacement.

X Releasethescrews[c]and[d]forsettingthesupportangle.

X Releasethescrew[g]forelevation.

X Thescrewsshouldbere-tightenedafterthesettingshavebeencarriedout.

[c] [g] [d][f][e]

Fig. 14a Forend raiser block 9003 and 9003 Precise

Fig. 14b Forend raiser block 9003 and 9003 Precise

27

20.2 Gripadjustment

Theriflegripcanberotatedinanydirection,tiltedanddisplacedinlengthbyreleasingthegripfixingscrew[a].Re-tightenthegripfixingscrew[a]afteradjustingthegrip.

Re-tightenthegripfixingscrew[a]slightlyfromtimetotimesincesettlingcanoccur.

[a]

Fig.15 Grip fixing screw

20.2.1Gripadjustmentonthe9003Precise

X Releasethescrew[a]and[b]slightlytopermitlateralgripadjustment.

X Lateraladjustmentandrotationmovementcanbecarriedoutbyadjustingtherotaryknobs[A1]and[B1].

X Re-tightenthescrews[a]and[b]afteradjustment.

[B1] [A1]

[b] [a]

Fig. 15a Grip adjustment on the 9003 Precise

28

20.3 PRO-Gripequipment(model-dependent)

The.grip,.the.cheek.piece.and.the.forend.of.the.aluminium.shaft.are.made.from.PRO-Grip.material..These.parts.can.be.adapted.to.the.requirements.of.the.marksman..The.PRO-Grip.material.can.be.treated.as.wood.for.this.purpose..If.the.surface.of.the.cheek.piece.is.too.rough,.this.can.be.smoothed.down.using.fine.glasspaper.(grain.size.200).

NOTe!

21Opticalsights/rearsight(option)

Operating.and.maintenance.instructions.can.be.found.in.the.individual.manufacturer's.documenta-tion.

NOTe!

21.1 MountingTherearsightisslidontothe11mmwideV-blockrailsandlockedinasuitablepositionusingthe2clampingscrews(justtightenhand-tight).

21.2 elevationandwindageadjustmentTheelevationandwindageadjustingscrewshaveclickstops.Thepositionoftheaimingpointismovedfromclicktoclick.y Elevationwhenshootinghigh=turnrotaryknobin"H"directiony Elevationwhenshootinglow=turnrotaryknobin"T"directiony Windagewhenshootingtotheright=turnrotaryknobin"R"directiony Windagewhenshootingtotheleft=turnrotaryknobin"L"direction

21.3 ZeroadjustmentAfterthesightshavebeenzeroed,thetwoadjustingscrewscanbesettothe"0"position.

X Releasethesetscrewsintherotaryknob.

X Positiontherotaryknobsto"0"onthescale.

X Tightenthesetscrewsintherotaryknobhand-tight.

$$ The$ANSCHÜTZ$rear$sight$is$aligned$with$zero$clearance$at$the$factory$and$does$not$require$further$adjustment.$For$this$reason$only$the$elevation$and$windage$screws$may$be$operated.

$$ Do$not$turn$the$knobs$beyond$the$stops$at$the$end$of$the$adjustment$travel$$(the$pre-tensioned$threaded$drive$can$be$damaged).

29

30

22Maintenance/cleaning22.1 General

Danger.to.life!

Dangertolifefromloadedfirearm.h Ensurethattherifleisunloadedbeforeuse

orduringmaintenanceandcleaningwork.

WaRNING!

Injury.and.physical.damage!

Dangerofinjuryorphysicaldamageasaresultofnotremovingtheoilfromthebarrelandchamber.

h Eachtimebeforeshooting,anyoilorforeignobjectsmustberemovedfromthebarrelandchamber.

CauTION!

Always.look.out.for.any.changes.or.damage..that.may.occur.to.the.rifle.In.the.event.of.a.change.or.damage,.the.rifle.must.immediately.be.taken.to.an.authorised.gunsmith..or.sent.to.ANSCHÜTZ.for.inspection.

CauTION!

The.rifle.should.be.protected.from.dust,.sand,....moisture,.heat.and.damaging.influences.

NOTe!

A.dry.cloth.is.adequate.to.clean.the.aluminium.stock..Under.no.circumstances.should.you.use.oil.

NOTe!

To.reduce.the.risk.of.breaking.the.stock.during.transport,.ANSCHÜTZ.recommends.separating.the.barrelled..action.from.the.stock,.especially.during.air.travel.

NOTe!

31

After.each.use.of.the.rifle,.apply.a.thin.film.of.oil.to.the.steel.parts.and.thoroughly.clean.the.barrel.

When.the.rifle.is.transported.from.cold.to.warm.rooms,.condensation.can.form.on.the.metal.parts.and.inside.the.barrel..If.this.condensation.is.not.quickly.dried.off,.it.can.possibly.lead.to.surface.rust.

No.other.aids.(felt.plugs,.non-approved.grease,.etc.).should.be.used.for.cleaning.the.barrel.ANSCHÜTZ.recommends.the.use.of.the.Cleaning.Kit.507.(Item.No.:.001491).for.cleaning

NOTe!

The.rifle.case./.soft.case.should.be.cleaned.regularly.and.any.dust.and.fluff.removed.

Rifle.cases.and.soft.cases.should.have.a.smooth,.dust-repellent.lining.

When.not.in.use,.the.rifle.case/soft.case.should.always.be.left.open.to.allow.moisture.to.escape..Enclosing.a.desiccant.can.reduce.the.moisture.content.

NOTe!

22.2 Maintenanceintervals

Beforeshooting

y Carefullyremoveanyoilfromtherifle.$$ The$de-oiling$of$the$rifle$should$be$carried$out$at$room$temperature,$as$too$many$residues$

can$be$left$in$the$barrel$if$it$is$very$cold.

y Firearound10shotstore-establishevenshotperformance(oilshots).

aftershooting

y Allowthefirearmtowarmuptoroomtemperaturewiththeactionopen.

y Carefullyremovecondensatefromtheoutsideparts.y Rubthefirearm(steelparts)downwithasuitablegunoil.

Intheeventofseverecontamination(2000-3000shots)oronceayearinthecourseofinspection

y Cleanthebarrelwithabronzebrush.$$ Do$not$pull$the$brush$backwards$and$forwards$in$the$barrel.

y Pullthecleaningwicksthroughthebarrelinadryconditionafewtimes,untilthefinalcleaningwickdoesnotshowanyappreciablecontamination.

y Rubthefirearm(steelparts)downwithanoilycloth.y Taketherifletoadealer/gunsmithforinspection.

22.3 Triggermaintenancey Toavoidgumming,adhesionorsoilingofthetriggerparts,neverwash

outtheinnerpartsofthetriggerwithasprayoroil.Keepthetriggerdryandfreefromdust.

$$ No$dirt,$solvent$residues,$grease$or$unsuitable$oils$must$get$into$the$trigger$assembly$during$maintenance$of$the$rifle.$ANSCHÜTZ$recommends$cleaning$the$rifle$on$its$side$or$with$the$stock$pointing$upwards,$which$will$prevent$any$adverse$effects$on$the$trigger$assembly.

22.4 Maintenanceoftheopticalsights

The.ANSCHÜTZ.rear.sight.is.a.precision.unit.and.consequently.requires.the.utmost.care.when..handling.Intensive.care.and.maintenance.guarantee.perfect.function.

The.rear.sight.must.be.protected.from.dust.and.dirt.

NOTe!

23Troubleshooting

In.the.event.of.malfunctions.(e.g..shots.not.discharged,.etc.).the.rifle.must.be.unloaded,.secured.and.taken.without.delay.to.a.specialist.dealer/gunsmith.or.sent.to.ANSCHÜTZ.

WaRNING!

24TechnicalData(model-dependent)

Weight 3.7 - 4.6 kg

Overall length 9003 Premium S2 Precise: 106 – 111 cm

9003 Premium S2 Precise BENCHREST: 103 – 108 cm

9003 Premium S2: 108 – 111 cm

8002 S2 ALU: 107 – 110 cm

8002 S2 BENCHREST: 105 – 108 cm

8001: 107 – 110 cm

Barrel length 64 cm

Rifling 42 cm

Barrelled action length

78 cm

Version Single loader

Calibre 4.5 mm

Propellant Compressed air (200 bar max.)

32

25Disposal

Thedisposaloftheriflemustbecarriedoutandcertifiedbyaspecialistdealerorgunsmith.

26Miscellaneous

AdditionalinformationisavailableontheInternetatwww.anschuetz-sport.com.

NewsaboutthisandotherproductsisalsoprovidedbyANSCHÜTZviathefree-of-chargesubscriptiontotheANSCHÜTZNewsletterontheinternet.

Theoriginalgroupforyourrifleat10misaffixedtotheCDcase.

www.anschuetz-sport.com

33

34

28Guarantee

< < < W A R R A N T Y > > >1. Material: This product has been released for sale after the product itself, its materials and individual components have been subjected to strict inspection, or the rifl e has demonstrated its durability and function during test shooting. J.G. ANSCHÜTZ GmbH & Co. KG offers a full guarantee covering material and manufacturing faults (excluding broken stocks and springs) for a period of two years, provided that the fault can be shown to have been present at the time of handover of the product. No warranty claims will be accepted by J.G. ANSCHÜTZ GmbH & Co. KG for faults that are the result of improper use or unauthorised repairs. The item will either be repaired or replaced at our discretion. Claims for compensation - put forward for any legal reason whatsoever – are excluded.

2. Shooting Performance: The purchaser undertakes to inform J.G. ANSCHÜTZ GmbH & Co. KG in writing of any faults detected in shooting performance within one month of purchase with the submission of their own shooting record. J.G. ANSCHÜTZ GmbH & Co. KG reserves the right to transfer the rifl e to an independent agency for inspection (DEVA or a national ballistics offi ce). Should such an agency confi rm excellent shooting performance, J.G. ANSCHÜTZ GmbH & Co. KG is entitled to charge the purchaser the costs of the rifl e inspection. The accepted warranties do not apply to rifl e damage resulting from mechanical effects and improper use or care by the purchaser. The warranty is excluded if the rifl e has been repaired or modifi ed by unauthorised persons. Likewise, the warranty is cancelled when using reloaded ammunition or ammunition which is not CIP approved.

In the event of a warranty/damage claim please enclose this card, completed and signed by your dealer, with the product.

J.G. ANSCHÜTZ GmbH & Co. KG · Jagd- und SportwaffenfabrikPostfach 1128 · D-89001 Ulm/Germany · www.anschuetz-sport.com

SERIAL-NO.:

DATE:

THIS ITEM WAS BOUGHT FROM: (Stamp and signature of dealer)

27ShootingPerformance

Theshootingprecisionofarifledependsonseveralfactors.Oneveryimportantfactorinthisrespectistheammunition.Noteverybarrelshootswiththesameefficiency.Considerableperformancedifferencesareapparentwitheachammunitiontype.Thesightsarejustasimportant.Assuch,onlyANSCHÜTZsightsshouldbeusedandtheammunitionmatchedtoyourrifle.Evenammunitionfromthesamemanufacturerandthesamebatchcan,fromoneproductionruntoanother,andfromonerifletoanother,resultinvaryingshootingperformanceandhittingaccuracy.Whenthemostsuitableammunitionandsightshavebeenselected,wecanguaranteetheexcellentshootingperformanceofourweapons.Seewarrantycard.