User's Guide for Iptime Ve

8/13/2019 User's Guide for Iptime Ve

1/54

Users Guide

www.zioncom.ne

t

-0-


2/54

Users Guide

www.zioncom.ne

Preface

This document is users manual for IP Router IPTIME VE.This manual consists of IP Router components, installation guide, settings, and

information on how to use IP Router and its functions.

It is recommended that you have a clear understanding of this manual before you

start using the IP Router.

Before you start

First, read Chapter 4, Installation section for installation information before

you install the IP Router.

Second, read Chapter 6. IP Router Setup section to setup the IP Router to

best fit your Internet environment.

t-1-


3/54

Users Guide

www.zioncom.ne

TABLE OF CONTENTS1.WARNING3

2.PACKAGE CONTENTS43.SPECIFICATION5

4.INSTALLATION.9

4.1 Before Installation ...9

4.2 Installation 9

4.3 Network Sketch Map 11

5.LOCAL COMPUTER SETUP..13

5.1 Windows 95/98/ME Setup 145.2 Windows 2000 Setup 19

5.3 Windows XP Setup 23

6.ROUTER SETUP28

6.1 Start Internet Explorer to Login 28

6.2 PPPoE User Setup 29

6.3 Dynamic IP User (Cable Modem...) Setup 34

6.4 Static IP User Setup .. .....38

6.5 Status 41

6.5.1 WAN Status 41

6.5.2 LAN Status 42

6.6 Basic Setup 43

6.6.1 LAN/DHCP Setup 43

6.6.2 Link/Info .46

6.6.3 Routing Table 47

6.7 System 48

6.7.1 Password . ......48

6.7.2 Default/Restart ..49

6.7.3 Firmware Upgrade 50

6.7.4 System Time 52

Appendix A. UTP Cable specif ication53

t-2-


4/54

Users Guide

www.zioncom.ne

1.WARNING

1. Use only the power adapter provided with the IP Router for power

connection. Using other power adapter may cause an error or damage to the

IP Router.

2. Do not drop or give a physical shock to the IP Router. It may affect internalcircuit.

3. Do not disassemble the IP Router without sufficient understanding of your

action.

4. Avoid direct exposure to the sun.

5. Do not leave the IP Router near moist or fire.

t-3-


5/54

Users Guide

www.zioncom.ne

2.PACKAGE CONTENTS

Package contents of IP Router IPTIME VE are as follows;

2.2 IPTIME VE Router

2.3 Switch DC Power Adapter (5V, 1A)

2.4 Ethernet Cable

2.5 Users guide

t-4-


6/54

Users Guide

www.zioncom.ne

3. SPECIFICATION

This IP Router is a highly integrated IP Router with many functions such as

Gateway, Switch, DHCP Server, Firewall etc

Network Address Transform (NAT) With providing Internet application

this IP Router can allow more than one user to connect with Internet at the

same time by sharing one public IP address; It supports many connectionways xDSL Cable Modem LAN/ Leased Line and so on.4 Ports 10/100M Switch It has 4 Network 10/100M switch ports port

support MDI/MDIX automatic identification function, Switch port can

connect to other switches, so that can support over hundred computers to

go to Internet at the same time.

Support VPN Pass-through Supports VPN Pass-through PPTP

dialogue and also supports users to configure VPN Server and Client in

LAN.

PPPoE(ADSL) Automatic Disconnection/Connection Users can

optionally choose automatic disconnection in idle time and connection in

access time to save Internet access cost.

Firewall Users can randomly refuse or allow data from Internet Support

DDOS protection and Ping forbiddance that can protect users from

Internet un-safety and virus such as shock wave.

DHCP Server All computers, which connect to Internet can get TCP/IP

configuration information from IP Router automatically, so that it can make

sure easy user management.

Static IP Address assign MAC address and IP address band and assign

function can make sure most user management administration in LAN.

Management Based on Web Page Both network configuration and

t-5-


7/54

Users Guide

www.zioncom.ne

system configuration are based on inside Web Server. The user interface

is clear and usage is easy. By this interface users can also update

software to enhance the system stability and expansibility.Internet Access Control Different administration can be setup for

different users.

Data Package Filtrate Port filtration, IP address filtration, MAC address

filtration, Keywords filtration allow users flexibly setup IP Router and judge

data has been refused/has accessed or not.

Virtual Server Allow other users from Internet access WWW, FTP server

or other servers in LAN.Connection Time Control Setup special connection time to flexibly

control the time for LAN accessing Internet.

DMZ Server Allow one computer to be totally open to Internet to make

sure special application.

Remote Management Users can totally manage office or home network

wherever they are.

DDNS By this function users can setup their own web station.

Remote Wake-up Computers in LAN can be woken up by remote control.

Detailed Specification

ITEM IPTIME VE

StandardIEEE 802.3, IEEE 802.3u, IEEE 802.x, IEEE Fast

Ethernet,

ProtocolTCP/IP, NAT, DHCP, UDP, FTP, PPPoE, PPTP, L2TP,

HTTP, DNS, IPSec/VPN Pass-through

WANOne 10/100Mbps RJ-45 port, automatic

sense cross cable

T e c h ni c

al p

ar am

e t er

External

PortLAN

Four 10/100Mbps speed Ethernet switch

port, auto sense cross cable

t-6-


8/54

Users Guide

www.zioncom.ne

Cable 100Base-T UTP/STP 5 or above standard

Control

interface Based on Web application

Inside

function

10/100Mbps swi tch

LAN/WAN port auto sense cross cable

WAN port static/dynamic IP flexible setting up

PPPoE dial-up and connection time setting up

PPPoE dial-up and automatic/manual connection

Support VPN Pass-through

DHCP Service

DNS relaying

DMZ Server

Static IP address assign

Connection setting up and stat.

Connection time limit

FirewallPort/IP/MAC/Keyword filtration

Remote control

Remote wake up

DDNS

Gateway

Virtual Server

Data forward

NAT NAPT and PAT

CPU ARM9 166MHz

FLASH 2MB Flash

P r o

d u c t

s p c i f i c

a t i

on

Memory 8MB SDRAM

t-7-


9/54


10/54

Users Guide

www.zioncom.ne

be informed. The users please take care of it by themselves.

4. INSTALLATION

4.1 BEFORE INSTALLATION 4.1.1. Firstly please confirm your computer OS (Windows 95,98,NT,ME,2000,

XP, Linux, Mac) and Web browser (Internet Explorer 4.0 with JavaScript function

Netscape Navigator 4.0 or above version) 4.1.2. Make sure there is LAN Card, which has been correctly installed in your

computer.

4.1.3. If you are xDSL user, please remember your user ID and password.

4.1.4. If you connect Internet by LAN or WAN , please get the following

information from your network administrator: IP address is static or dynamic, DNS,

default gateway, account and so on.

If your computer has installed ADSL PPPoE dial-up software before the

installation of IP Router, please backup your installation software and uninstall your

ADSL PPPoE dial-up software by Start->control panel->Add or Remove Programs.

4.2 INSTALLATION4.2.1. Setup WAN connection: connect broadband cable (xDSL, Cable Modem

or LAN/ Leased cable) with WAN port of IP Router.

4.2.2. Setup LAN connection: connect your computer LAN cards port or your

switch UPLINK port with one LAN port of IP Router by a common network cable.

Note: All L AN ports o f IP Router can automatically sense cross cable, so

you can either use through cable or cross cable to connect LAN card or

switch.

4.2.3. Turn on the power: connect and the power supply, turn on it. Then IP

Router comes to self-detect state. During the self-detect: PWR LED will be long

t-9-


11/54

Users Guide

www.zioncom.ne

light, RUN LED will slow flash after correct startup, other four LAN LED and WAN

LED will flash only twice rapidly, then the system will come to normal work state.

4.2.4. Start computerLED explanation

RUN System status LED, slow flash after correct startup.

POWER Power LED, long light

WAN WAN port connection LED, flashing refers to data transformation

LANLAN port connection LED (1,2,3,4), flashing refers to data

transformation

POWER (red): power

connection state

RUN: system running

state

WAN (green): WAN

LAN (green): LAN port

Port explanation

WAN port Connect xDSL/Cable Modem or Special cable

LAN port Connect personal computer or hub, switch and so on

Power jack Connect power adapter (5V/1A)

ResetPress Reset button. Switch the power off/on. After

switching the power on, about 5 seconds later RUN

t-10-


12/54


13/54

Users Guide

www.zioncom.ne

4.3 NETWORK SKETCH MAP

DC Adapter: 5V/1A

3. connects with

power adapterModem PC

2. connects with PC1. connects with

xDsl Modem

EXAMPLE 1.

Internet

Cable/xDSL

Modem

ipTime VE Router

Server

t-12-


14/54

Users Guide

www.zioncom.ne

EXAMPLE 2.

ipTime VE Router

Switch

nternetCable/xDSL

Modem

Server

Server

Note During the usage, the sequence of turn on is firstly turn on Modems

power supply 1 minute after Modem startup tu rn on IP Router power supply ,

then turn on th e compu ter .

5. LOCAL COMPUTER SETUP

Users should configure local network to access Internet by IP Router.

Users should know the default configuration of IP Router before installation.

Users must connect with IP Router again after configure computers local

network. Please make sure your computer setting is as follows, Otherwise IP

Router cannot be correctly connected (Linux and Mac users please setup as

t-13-


15/54

Users Guide

www.zioncom.ne

follows by relative conference).

The default configuration of IP Router is:

IP address 192.168.0.1 Subnet Masks 255.255.255.0

Users can setup static or dynamic IP configuration.

5.1 Windows 95/98/ME SETUP

(1) Install IP Router.

(2) Start computer with Windows-95/98/ME, and check the LAN LED is onor off. If off, please confirm the connection between your computer and

IP Router.

(3) Click Start ->Setting -> Control panel .

(4) In Control panel double click Network .

t-14-


16/54

Users Guide

www.zioncom.ne

(5) Click TCP/IP and Properties .

t-15-


17/54

Users Guide

www.zioncom.ne

(6) Click IP address option and choose Obtain an IP address

automatically .

(7) Click Gateway menu and make sure Installed gateways is blank.

(8) Click the DNS Configuration and select Disable DNS , then Click

OK.

(9) During the TCP/IP installation process there will ask you to insert

Window installation CD. After inserting it then click OK.

(10) After TCP/IP configuration has completed, the window of System

Setting Chang will pop-up, select Yes , then restart computer.

t-16-


18/54

Users Guide

www.zioncom.ne

(11) After restart, click start -> run .

(12) Input command then click OK

(13) Input ipconfig in pop-up command window, then Enter .

(14) Please make sure your IP is the same with below. If same then your

configuration is successful, or please redo the above step and restart

your computer.The IP address is between 192.168.0.2 and192.168.0.254 The subnet mask is 255.255.255.0 The default gateway is 192.168.0.1

t-17-


19/54

Users Guide

www.zioncom.ne

(15) Input ping 192.168.0.1 then Enter .

t-18-

(16) If you can see Reply from 192.168.0.1: bytes=32 time=2ms TTL=64 the

connection between your computer and IP Router is completed.


20/54

Users Guide

www.zioncom.ne

5.2 Windows 2000 SETUP(1) Install IP Router.

(2) Start Windows 2000 and check LAN LED is on or off. If off, pleaseconfirm the connection of your computer with IP Router.

(3) Click start ->Setting -> Panel Control .

(4) Double click the Netwo rk and Dial-up Connection in control

panel .

t-19-


21/54

Users Guide

www.zioncom.ne

(5) Click Local area connection -> Properties -> Internet protocol

TCP/IP and Properties .

(6) Click General bar, Select Obtain an IP address automatically and Obtain DNS server address automatically

(7) Click OK.

t-20-


22/54


23/54


24/54

Users Guide

www.zioncom.ne

5.3 Windows XP SETUP(1) Install IP Router.

(2) Start Windows XP and check LAN LED is on or off. If off, please confirmthe connection of your computer with IP Router.

(3) Click Start ->Setting -> Panel Control

(4) Double click the Netwo rk and Internet Connections in control

panel .

(5) Click Network connection -> local area

connection -> properties -> Internet protocol TCP/IP and

Properties .(6) Click General ,Select Obtain an IP address automatically and

Obtain DNS server address automatically

(7) Click OK

t-23-


25/54

Users Guide

www.zioncom.ne

t-24-


26/54


27/54

Users Guide

www.zioncom.ne

(8) Click Start ->Run

(9) Input cmd , Click OK

(10) Input ipconfig in the pop-up command window.

(11) Please make sure your IP is the same with below. If same then your

configuration is successful, or please redo the above steps and restart

your computer.The IP address is between 192.168.0.2 and192.168.0.254

The subnet mask is 255.255.255.0 The default gateway is 192.168.0.1

t-26-


28/54

Users Guide

www.zioncom.ne

(12) Input ping 192.168.0.1 , then Enter . (13) If you can see Reply from 192.168.0.1: bytes=32 time=2ms TTL=64 then

the connection between your computer and IP router is completed.

t-27-


29/54


30/54


31/54

Users Guide

www.zioncom.ne

Select PPPoE User (ADSL) radio button.

Key in the User ID and Password provided by your Internet serviceprovider.Click the Apply button.You may see the popup window.

In case Conn. Status is Successfully connected , the configuration is

correct.Click Show Internet connection status and see the 6.5.1.

t-30-


32/54

Users Guide

www.zioncom.ne

If In case Conn. Status is Invalid ID/password , the configuration is

incorrect.

t-31-

Click the close button and check your ID& password.

If Conn. Status keeps unchanged, check whether your service type iscorrect.Confirm the WAN connection status: If WAN connection is successfullyestablished, then by clicking Show Internet Information you can enterWAN status web page; or click Status -> WAN status , as thefollowing.

Connection Type should be PPPoE (ADSL)

Connection Status should be successfully connected Physical Address is shows Router WAN port MAC Address.WAN IP Address , Subnet mask , Default Gateway , Primary DNSserver and Secondary DNS server can be different from thefollowing values. (These addresses are provided by your ISP)


33/54

Users Guide

www.zioncom.ne

Disconnect is manual disconnection button. If you click then

the system will disconnect with Internet

Connect is manual connection button. By clicking it the

system can be connected to Internet again.

Click Save to save current configuration.

t-32-


34/54

Users Guide

www.zioncom.ne

Restart all PCs connect with IP Router.

Notes: Please save IP Router Configuration after completion, otherwise

configuration will lose when power off or restart.

Other Configuration:

MTU: Input MTU value of data package, default value is 1454. Normally

please do not change it.

Disconnect PPP session if idle time is longer than Min : If you

choose this option and setup the time T, then the IP router

automatically disconnects from Internet after T idle time.

Connect On Demand: IP Router can automatically connect with

Internet if there is Internet access after disconnection. Note: during

usage if there is disconnection due to external causes, then the IP

Router will try to connect with Internet at once until successful

connection. This function is the IP Router inner function and does

t-33-


35/54

Users Guide

www.zioncom.ne

nothing with Connect On Demand function. Connect On Demand is

only effective to Disconnect PPP session if idle time is longer than

Min .Connect Manually: By this option users have to connect with Internet

manually after disconnection. This option is only effective to Disconnect

PPP session if idle time is longer than Min .

Prevent reconnection although no response from PPP server: This

option is to shut off IP Router inner automatic connection function. By

choosing this option if external network disconnects, IP Router will not

try to connect at once.

6.3 DYNAMIC IP USER (Cable/Modem) SETUP

By this connection way IP Router can get IP address automatically from ISP

(such as: CHINA TELCOM). It is suitable for connection ways such as Cable

Modem, LAN and so on.

Turn on the external Cable Modem and check the WAN LED of IP

Router.

If WAN LED is off, please re-confirm the network cable between

external Modem and WAN port.

Click Basic Setup -> WAN Setup as diagram:

Choose Dynamic IP user (Cable Modem)

Click Apply to complete.

t-34-


36/54

Users Guide

www.zioncom.ne

You will see the following pop-up window

If Conn. status is Successful connected , the configuration is correct.Click Show Internet Information and see the 6.5.1

If connection status keeps to be Connecting to Internet , please do the

following steps:

Close the pop-up window.

t-35-


37/54


38/54

Users Guide

www.zioncom.ne

Connect button is manual WAN port IP address refresh functionbutton. If click it WAN port will re-get dynamic IP address andconnect with Internet.

Click Save button to save current configuration, then restart all PCs

connected with IP Router

Note:

After completed setup , please save IP Router configuration , otherwise

t-37-


39/54


40/54

Users Guide

www.zioncom.ne

Input WAN IP address , Subnet mask , Default Gateway , Primary DNS

Server and Secondary DNS Server provided by ISP.

Click Apply to complete.You will see the following pop-up window:

Check WAN connection status: If it is Configuration is done , click

Show Internet Information to enter WAN status page; or click

Status ->WAN status , as following diagram:

t-39-


41/54


42/54

Users Guide

www.zioncom.ne

6.5 STATUS6.5.1 WAN Status

Click Status -> WAN Status as following:

This page shows current Internet connection status (WAN port), including

Connection Type , Connection Status , WAN IP address, Subnet mask , Default

Gateway and DNS server . If it is dynamic IP way, Disconnect button or

Connect button will be shown above. Click Disconnect button to release

current WAN Port IP Address, then click Connect button to refresh WAN IP

address; If it is PPPoE way, then Connect or Disconnect button will be shown

above. Click Connect button to connect with Internet, click Disconnect button

to disconnect with Internet.

Refresh Refresh current web page. All of the following web pages will

have this button with the same function.

Save Save IP Router current configuration. All of the following web pages

will have this button with the same function.

t-41-


43/54

Users Guide

www.zioncom.ne

6.5.2 LAN StatusClick Status > LAN Status as following:

LAN Information: Display LAN port Physical Address, current LAN

connection status (LAN port) and DHCP server Status, including the IP

address range and quantity to LAN IP address and subnet mask, DHCP

Server.

Allocated IP Informat ion: display the IP address information, which has

been rented by DHCP Server.

Number The location in list

IP address IP address which has been allocated to clients by

DHCP server.

Physical address MAC address of client computer.

t-42-


44/54

Users Guide

www.zioncom.ne

6.6 BASIC SETUP

6.6.1 LAN/DHCP SetupClick Basic Setup -> LAN/DHCP SETUP as following:

t-43-


45/54

Users Guide

www.zioncom.ne

LAN port basic parameter and DHCP server parameter can be setup in this

web page.System IP Setup If you want to change IP Router LAN port address, you

can setup as follows:

System IP address IP address in LAN. This IP address is factory

default value 192.168.0.1 , and you can change it.

Subnet Mask Subnet mask in LAN. This value cannot be changed.

TCP/IP protocol configuration includes IP address, subnet mask,

Gateway and DNS server and so on. It is not easy to configure TCP/IP

protocol correctly in all computers in LAN, but it is lucky that DHCP Server

has provided this function. If you choose the DHCP function, you can let

DHCP Server configure TCP/IP protocol in all computers in LAN

automatically.

DHCP Setup : If you want to able or disable DHCP Server, change DHCP

address range, you can choose the following options:

DHCP Server Status Display DHCP Server current status.

DHCP Server Operation Able and disable DHCP Server. The default

value is able DHCP Server.

DHCP IP Pool IP address range automatically allocated by DHCP

Server is address pool.

Manual DNS configuration: Let DHCP Server automatically allocated

the DNS Server to Client PC.

t-44-


46/54


47/54

Users Guide

www.zioncom.ne

6.6.2 Link Setup/InfoClick Basic setup -> Link Setup/Info as follows:

All IP Router ports speed, Link information and port statistics data and so on

can be setup by this web page:

Link Setup Setup every ports connection speed.

t-46-


48/54


49/54


50/54

Users Guide

www.zioncom.ne

6.7.2 Default/RestartClick System -> Default/Restart as follows:

Click Factory default button to restore all configuration of IP Router to

factory default values.

Default username root

Default password none

Default IP address 192.168.0.1

Default subnet mask 255.255.255.0

After restore to factory default values, IP Router will restart automatically.

Click Restart System button, IP Router will restart.

t-49-


51/54

Users Guide

www.zioncom.ne

t-50-

6.7.3 Firmware UpgradeClick System -> Firmware Upgrade as follows

By updating the IP Router software, you can get new functions or

performance.

Software update steps:

1) Login our company homepage www.zioncom.net , download new

version software to your local hard disk.

* Please notice production and software type.
http://www.zioncom.net/http://www.zioncom.net/


52/54

Users Guide

www.zioncom.ne

2) Click Browse button to choose you downloaded file.

3) Click Upgrade button to upgrade system software.

t-51-


53/54

Users Guide

www.zioncom.ne

4) After update, IP Router will restart automatically.

5) Please check you firmware version.

Note:

Update phase is about 30 seconds. During the update progress

please do not turn the power off otherwise the IP Router wi ll be damaged.

6.7.4 System TimeClick System -> System Time as follows

Set the time here by entering it manually or use NTP (Network Time Protocol.)

NTP is standard protocol on the Internet that synchronizes the time settings

accurately for all the computers on your network.

Current System Time: Current time of router.

Time Server: Select a Time Server for synchronize the time.

t-52-


54/54

Users Guide Standard Time Zone: Select your time zone from the pull-down menu.

If use that Scheduler in the advanced function can work well. Please setup

correct system time. After choose correct time zone click Apply to update thecurrent time of IP Router; If can not update correctly, please choose other time

server till success.

Appendix A UTP Cable specification

Twisted pair Category-5 straight-through cableTwisted pair Category-5 Cross over cable

Date post:	04-Jun-2018
Category:	Documents
Upload:	marcu-traian
View:	219 times
Download:	0 times

User's Guide for Iptime Ve

Documents