User's manual series(HMI) - HNC Electricfile.hncelectric.com/201412/02/201412021029590312.pdf ·...

HECHUANFX2N-32MR

HECHUANFX2N-32MR

HCFA CORPORATION LIMITED

User's manual

Thanks for purchasing HCFA HMI products!

Our hard working, your better life!

series(HMI)

Port

Port

Port

Notes:For communication protocol, refer to section 1-1 for more details.For communication parameter, refer to section 1-3 for more details.

Make sure COM2 communication port and attached cable

TP13-PLC-R4-8P-3M are used in HCFA HC/LC series.

Communication type is set to RS422 in the software.

1-1 Serial communication port

Series UPU Link port Communication protocolParameter setting

Series

Refer to section 1-3-1
















Dedicated Protocol(Mult i-Stat ion)





1-2 Serial port parameter and cable fabrication

Series

Series UPC Link port COOM Type Parameter Cable

Refer to section 1-5











Updated HCFA PLC Model name

1-3 Communication Setting

1-3-1 When Using HCFA HCA1, HCA2, HCA5, HCA6, HCA8 Communication Protocols

HMI SettingsHMI default communication parameters: 9600bps (Baud Rate), 7 (Data Bit), even (Parity Check), 1 (Stop Bit) and 0 (PLC Station No.)The PLC Communication Time Out, Max interval of word (bit) block pack, Max size of word(bit) block package on the right of the dialog box vary with PLC protocols. Generally the defaults are selected.

RS422 Communication

RS232 Communication

PLC SettingsThe PLC setting is as shown below when HCFA HCA1, HCA2, HCA5, HCA6, HCA8 communication protocols are used:1. Double-click the [PLC Parameter] under [Project Data List] in TP-Software

2. Open the [TX Parameter] dialog box.

3. Click the [Default] button to make settings without checking the [Communication Setting]:

Note: 1 The communication protocols such as HCFA HCA1, HCA2, HCA5, HCA6, and HCA8 etc. can be selected according to PLC model if the Station No. is not used when the communication is realized through the communication function expansion board.' 2 Make sure the value of communication format D8120 is 0 when the communication is realized through the communication function expansion board.

1-3-2 When Using 'Dedicated protocol (Multi-station)' Communication Protocols

HMI SettingsHMI default communication parameters: 19200bps (Baud Rate), 7(Data Bit), even (Parity Check), 2 (Stop Bit) and 0 (PLC Station No.)Note: The protocols are only applicable to PLCs communicating through communication function expansion board and support Multiple Station No. and Baud Rate settings

RS422 Communication

RS232 Communication

PLC SettingsThe PLC setting is as shown below when 'Dedicated protocol (Multi-station)' communication protocols are used.1. Double-click the [PLC Parameter] under [Project Data List] on the left of TP-Software.

2. Open the [TX Parameter] dialog box.

3. Parameters for HCA1, HCA2 and HCA5 are shown below.

Check the [Operate communication setting] optionNote :1 Set the parameters as follows.The [Dedicated Protocol] is selected for Protocol, the [Sum Check] is checked, and [Form4] is selected for the Transmission Control Sequence.

4. Parameters for HCA8 are shown below.

Check the [Operate communication setting] option.Note: 1 The [CH1] should be selected for HCA8 Series PLC. 2 Set the parameters as follows.[Dedicated Protocol] is selected for Protocol, [Sum Check] is checked, and [Form4] is selected for the Transmission Control Sequence.

Aside from using [HC Parameter], the user can use the special data register D8120 in PLC to set the communication parameters for PLC.

Special Data Registers Descriptions

D8120

D8121

D8129

Applicable to HCA8 and other HC Series PLCs using CH1

Communication format

Station No. setting

Data network out-time counting

* For example:If the PLC communication parameters are: 9600bps (Baud Rate), 7 (Data Bit), even (Parity Check), 2 (Stop Bit), 1(PLC Station No.), RS485 (Communication Method) and 1) (PLC Communication Time Out), then D8120=0xE08E, D8121=1, and D8129=1. Note: The settings will be valid when the PLC is restarted after the D8120 setting is modified.

1-3-3 When Using HCFA HCA4 Communication Protocols

HMI SettingsHMI default communication parameters: 19200bps (Baud Rate), 7(DataBit), even (Parity Check), 2 (Stop Bit) and 0 (PLC Station No.)

Rs422 Communication

PLC SettingsDouble click [Setting] in the [Working list] of LC-Develpoer.

Click the built-in RS422C port

Before After

When using DC+5V power supply voltage of 6-pin connector from serial port COM1, confirm the consumption current of connecting devices is below 250mA.The voltage output of the TP Unit for the TP Unit is +5V±5%. The maximum current is 150mA.

Precaution for safe use

Pins Singals

Sending data

Receiving data

DC+5V output (Max. current: 250mA)

Signal ground

Functions

1-4 Supported Registers

Device Bit Address Word Address Format Notes

Input Relay

Output Relay

Auxiliary Relay

Timer Contact

Counter Contact

Data Contact

State

Timer Value

Counter Value

Data Register

Special Data Register

Counter Value(32-bit) bit device


Input Relay

Output Relay

Auxiliary Relay

Timer Contact

Counter Contact

Data Contact

State

Timer Value

Counter Value

Data Register




Input Relay

Output Relay

Auxiliary Relay

Working Area

Holding Area

Data Register

Timer Value

Timer Contact

Counter

Counter Contact

Auxiliary Register

E-type CPU unit

N-type CPU unit

Read only

Read/ write


Input Relay

Output Relay

Auxiliary Relay

Timer Contact

Counter Contact

Data Contact

State

Timer Value

Counter Value

Data Register




Input Relay

Output Relay

Timer Contact

Counter Contact

Data Contact

State

Internal Relay

Special Internal Relay

Timer

Counter

Data Register

Extension Register



1-5 Cable Fabrication

1-5-1 RS232 Communication Cable for HC seriesCPU port RS232 communication cable

Make sure to use serial communtication port cables of HC series.

TX□□-232-BD Communication cableHMI (Male) port PLC RS232

(Female) Port

1-5-2 RS485/422 Communication cable for HC seriesCommunication cable

HMI (Male) port PLC RS422 (Female)

Port

Communication cableHMI (Male) port

Connetor

BackV iew

Ethernet

Input terminalDC24V

min USB Programingport

RESET

COM1(Female)-RS232

COM2(Female)-RS422/RS485/RS232

1-6 Installation onto the Operation PanelInstall the TP Unit by embedding it into the operation panel.

Use the metal kit and tool (a crosshead screwdriver) supplied with the Unit for installation.

Proceed the installation following the procedures below.

1. Panel cutout with dimensions is shown below. Fit the TP Unit into the panel from the front side.

Width

HeightOpening dimensions

2. Installation method of TP unit is shown below.

Models Opening Dimension (W * H mm)

Gaskets

Ampinfied parts

Gaskets

Gaskets groove

Sectional view

Insert Mounting holes

Installationaccessories

Screws

Amplified parts


■ When operating on the operation panel, make sure to keep metal particles from entering the Unit.■The mounting panel must be between 1.6 and 4.8 mm thick. The NB Unit must be installed in a control panel.■For the sake of waterproof and dustproof, all the fixators must be evenly tightened

or the tightening is not even, deformation of the front panel may occur.■Make sure that the operation panel is clean, unbent, and strong enough for the installation process.

to a torque of 0.5~0.6 N▪m. If the tightening torque exceeds the specified value,

1-7 Part names

TL1310-TFT

Front view

POWER LEDlit/Not lit when the powerNO/OFF

Display7-inch WVGA wide TFT LCDInpout operation cn be carried out by the touch panel.

Back wiew

Ethernet

min USB Programing portCOM2(Female)-RS422/RS485/RS232

DC24VInput terminal

RESET

1-8 Part Specifications●Touch PanelInput operation can be carried out by means of the touch panel. By pressing the touch panel, the screens can be switched, and the contact information can be transmitted to the host.

■Press a touch switch with a 0.8~1.2N force.■Do not accidentally press the touch panel when the backlight is not lit or when the display does not appear. Make sure of the safety of the system before pressing the touch panel.■Confirm the safety of the system before pressing the touch panel.■Do not use hard or pointed objects to operate or scrub the screen, or the surface of the screen may be damaged.■Signals from the touch switches may not be input if the switches are pressed consecutively at high speed. Confirm each input before proceeding to the next one.■Deterioration over t ime can cause the touch points to move. I f deviation of the touch points stands out, calibrate the touch panel periodically.

Precautions for Safe Use

●Serial Port COM1■TL1370-WTFT &TL1310-WTFTSerial port COM1 is a 9-pin D-type socket port. This port supports RS-232C communicat ion funct ion, making i t connectable to a control ler which features RS-232C funct ion, and i t can also be used for downloading programs or debugging for the product.The pins are defined as fol lows:

Pins SingalsFunctions

Terminal R1

Terminal R1

Sending data

Receiving data

Terminal resistor 1

Terminal resistor 2

Receiving data

RS485B

RS485A

Sending data

Receiving data

Sending data

Receiving data


Confirm the safety of the system before turning ON or OFF the power supply, or pressing the reset button.

■TL1370-WTFT &TL1310-WTFT●Serial Port COM2

Serial port COM2 is a 9-pin D-type socket port. This port supports RS-232C/RS-485/RS-422A communication function.The pins are defined as follows:

COM1(Female)-RS232

1-9 Part names

页 1页 2

Date post:	29-Jan-2021
Category:	Documents
Upload:	others
View:	3 times
Download:	0 times

User's manual series(HMI) - HNC Electricfile.hncelectric.com/201412/02/201412021029590312.pdf ·...

Documents