2
Using for the first time Operation Drying Changing the programme sequence Fragrance flacon M.-Nr. 11 385 100/01 This dryer has 2 places for inserting fra- grance flacons. Use one or both when- ever you want to add a pleasant fra- grance to your laundry. ɒClose the unused socket. ɒBefore using a fragrance fla- con, please read "Warning and Safety instructions - Using a fragrance flacon (optional accessory)" and "Fragrance flacon" in the operating instructions. Inserting a fragrance flacon 1. 2. 3. 4. Markers and must line up with each other. 5. 6. ĺ Turn the outer ring clockwise a little. Markers und must line up with each other. Before drying ĺ Turn the outer ring clockwise a little. The further you open the flacon, the more intense the fragrance. After drying To avoid the fragrance escaping need- lessly: ĺ Turn the outer ring anti-clock- wise until marker is in position . If you want to dry laundry without add- ing fragrance: Remove the fragrance fla- con and store it in its original packaging. Before cleaning the fluff filters ĺ Remove the fragrance flacon. ĺ Only store the fragrance flacon in its original packaging. ɒNever lay the fragrance flacon down. Otherwise the fragrance will leak out. TWR 860 WP en - AU, NZ ɒBefore using the tumble dryer for the first time, ensure that it is correctly installed and connected. After installation, a downtime of 1 hour is required before connecting the tumble dryer to the electricity supply. Otherwise the heat pump can be damaged. It is essential to read the operating instruc- tions. OPERATION DRYING CHANGING THE PROGRAMME SEQUENCE 1 Condensed water container – empty after each drying programme – Steam care programme: Note –min– marker 2 Door 3 Control panel 4 Access panel for the heat exchanger and plinth filter – do not open during drying 5 Cool air intake grille – do not obstruct with a laundry basket or other objects 1 sensor Takes you back a level in a menu. 2 Touch display 3 Start/Stop sensor Touching the Start/Stop sensor starts the selected programme or cancels a programme that has already started. The sensor flashes slowly as soon as it is possible for a programme to be started and then lights up constantly after the programme has started. 4 Optical interface For service technicians. 5 sensor For switching the tumble dryer on and off. To save energy, the tumble dryer will switch off automatically. This occurs 15 minutes after the end of the programme/Anti-crease phase, or after being switched on if no further selection is made. Touch display and sensor controls The and Start/Stop sensors and the sensors in the display react to fingertip con- tact. The touch display can be scratched by pointed or sharp objects, e.g. pens. Only touch the display with your fingertips. Main menu After switching on the tumble dryer, the main menu will appear in the display. You access all the important sub-menus from the main menu. Touch the sensor at any time to return to the main menu. Changes made before this that have not been confirmed will not be saved. Programmes For selecting drying programmes. Favourite programmes You can save your own customised drying programmes. MobileStart With MobileStart you can operate your tumble dryer remotely with the Miele@mobile App. Drying assistant The Drying assistant guides you step by step so that you can select the optimum drying programme for your laundry. Settings You can alter the tumble dryer's electronics to suit changing requirements in the Set- tings menu. Operating the touch display Scrolling You can scroll to the right or the left by swiping your finger across the screen. The orange bar under the pictures shows that there are further options to choose from. Selecting Touch an option in the menu to select it. If there are multiple options, the selected option will be highlighted in orange. Pull-down menu Touch the top edge of the screen in the middle and drag down with your finger. Switching on the tumble dryer ĺ Press the sensor. The welcome screen will light up. The display will guide you step by step through the initial commissioning process. For further information, please refer to the separate operating instructions. 2. Selecting a programme ĺ Touch the Programme sensor. ĺ Scroll to the right of the display until the desired pro- gramme appears. ĺ Touch the sensor for that programme. ĺ You can change the drying level or the duration. The display will change to show the Overview menu. There are 3 further ways of selecting a programme. 1. Favourites 2. Drying assistant 3. MobileStart 11:02 2:35 Overview Cottons h Timer Save Drying level Normal Extras not selected 11:02 0:00 0:00 0:00 0:00 h h h h Programmes Cottons Delicates Cottons Minimum iron Help 1. Notes on correct laundry care ɒEnsure that any foreign objects (e.g. detergent dis- pensing balls, lighters, etc.) have been removed from the laundry. Such items could melt or explode and cause damage to the dryer or the laundry. ĺ Sort the laundry according to the type of fibre and weave, size, garment care label symbol and the drying level required. ĺ Check seams and stitching to ensure that padding and linings are intact. ĺ Fasten duvet covers and pillow cases to prevent small items from being rolled up inside them. ĺ Tie together textile belts and apron ties. ĺ Sew in or remove loosened underwiring from bras. Energy saving tips – Spin the laundry at the highest possible speed in the washing machine – Dry a full load – Keep room temperature not too warm – Clean the fluff filters 5. Programme start The programme can be started when the Start/Stop sensor is flashing on and off. ĺ Touch the Start/Stop sensor. The Start/Stop sensor lights up constantly. 6. End of programme - unloading the drum The programme is finished when Finish/ Anti-crease phase appears in the display. The Start/Stop sensor no longer lights up. – To save energy, 10 minutes after the end of the programme the Start/Stop sensor will begin to flash slowly and the display will go out. – The tumble dryer switches off automati- cally. ɒDo not open the door before the end of the programme. ĺ Open the drum door. ĺ Remove the laundry. ɒCheck that all items have been removed from the drum. If items are left in the dryer, they could be damaged by overdrying when the dryer is used the next time. If the dryer is switched on at the mains and the door is opened, the drum lighting will come on. It will go out after a few minutes to save energy. ĺ Switch the tumble dryer off with the sensor. ĺ Clean the fluff filters. ĺ Close the drum door. ĺ Empty the condensed water container. 4. Loading the tumble dryer ĺ Open the drum door. ĺ Unfold the laundry and load loosely into the drum. ɒDo not overload the drum. Overload- ing can cause unnecessary wear and tear of the laundry, give a disappointing drying result and cause more creasing. ɒIf you are not using a fragrance flacon: the tabs must be pushed down com- pletely (see arrow) to ensure both sockets are closed. ɒWhen closing the door, make sure that laundry does not get trapped in the door opening. ĺ Shut the door with a gentle swing. Emptying the condensed water container Empty the condensed water container after every drying programme. Empty the container or check the drain outlet. will light up in the display if the max- imum level of the condensed water con- tainer is reached. To turn the message off: Open and close the door while the dryer is switched on. ĺ Close the drum door. ĺ Pull out the con- densed water container. ĺ To prevent water running out, keep it in a horizontal position when carrying it. Hold it at the front and towards the back. ĺ Empty the container. ĺ Replace the con- tainer in the dryer. ɒDo not drink condensed water. It can cause health problems in people and ani- mals. Adding or removing laundry You have forgotten an item of laundry, but the programme has already started. ĺ Touch the Add laundry sensor*. The following appears in the display: Add laundry and The door can be opened. The Start/Stop sensor flashes slowly. ĺ Open the door. ĺ Add or remove laundry. ĺ Close the door. ĺ Touch the Start/Stop sensor. The programme will continue. * Exceptions to adding laundry In some cases, e.g. during the cooling phase or in the Proofing programme, you cannot add laundry. Changing a programme after it has started You cannot change to another programme once a programme has started (this pre- vents unintentional alterations). You will need to cancel the current pro- gramme before you can select a new one. ĺ Touch the Start/Stop sensor. The following appears in the display: Cancel the programme? ĺ Select yes. The following appears in the display: Programme cancelled. ĺ Open the door. ĺ Close the door. ĺ Select the required programme. ĺ Touch the Start/Stop sensor. 3. Selecting programme settings Programmes with drying levels Cottons, Minimum iron, Delicates, Bed linen, Automatic, Express, Shirts, Denim, Steam care, Sportswear, Outer- wear, Pre-ironing The preset drying level can be changed. ĺ Touch the Drying level sensor. ĺ Scroll in the display until the desired drying level appears. ĺ Touch the sensor for that drying level. Timed drying programmes and other programmes Warm air, Cool air, Basket programme You can change the duration in 10-minute increments. ĺ Touch the Duration sensor. ĺ Place your finger on the number that you want to change and move your finger in the direction you want. ĺ Confirm with the OK sensor. Cottons, Woollens handcare, Silks handcare, Proofing, Standard pillows, Large pillows, Cottons hygiene The drying result is preset by the dryer and cannot be altered. Selecting Extras ĺ Touch the Extras sensor. ĺ Touch the sensor for the Extra you want. ĺ Confirm with the OK sensor. Freshen up For removing or reducing odours in clean (dry or damp) clothing. Gentle tumble Low temperature drying for delicate fabrics with the symbol on the care label, e.g. acrylic garments.
