V8 Thunder Cars NEZ regulations... · V8 Thunder Cars NEZ North European Technical Regulations...

V8 Thunder Cars NEZ North European Technical Regulations 2016-2018

V8 Thunder Cars NEZ

North European Championship Technical Regulations 2016-2018

Edition (English version): Update March 2018


Contents

1 Definitions 4

1.1 Eligible Cars 4 1.2 Limitations 4 1.3 References 4

2 Homologation 4

3 Oversight of Regulations 4

4 Weight Limits 5

5 General 5

5.1 Engine 5 5.2 Electrical System 6 5.3 Exhaust System 7 5.4 Mounting of Front to Front Fenders 8 5.5 Fuel 8 5.6 Upper A-Frame Mounting 8

6 Transmission 9

6.1 Gearbox 9 6.2 Shifter Mechanism 9 6.3 Rear Axle 10 6.4 Drive Shaft 10 6.5 Master Cylinder 9


6.6 Clutch Cover 10 7.0 Wheels 10

7.1 Rims 10 7.2 Tires 10 8.0 Brakes 10 8.1 Front Brake Discs 11 8.2 Rear Brake Discs 12 8.3 Brake Pads 11 8.4 Brake Cylinder 11 8.5 Update Kit – Brakes 12

9.0 Chassis/Body 12

9.1 Minimum Heights 12 9.2 Steering Wheel 12 9.3 Seat 12 9.4 Foot Rest 12 9.5 Chassis and Body 12 9.6 Shock Absorbers 13 9.7 Springs 13 9.8 Front Anti-Roll Bar 14 9.9 Rear Anti-Roll Bar 14

10 Safety Equipment 14

10.1 Roll Cage 14 10.2 Safety Belt 14 10.3 Fire Extinguisher 14 10.4 Safety Fuel Cell 15 10.5 Defuelling of Fuel Cell/ Fuel Sample System FIA 15 10.6 Other Safety Regulations 15

11 Appendixes 16

11.1 Appendix 1.1 16


11.2 Appendix 1.2 16 11.3 Appendix 1.3 16

1 Definitions 1.1 Eligible Cars Cars delivered by Performance AutoMotive Scandinavian AB (PASAB). Eligible models: Chevrolet Camaro Gen.5 and Gen.6, Ford Mustang Gen.5 and Gen. 6 and Dodge Challenger Gen.3 with chassis marked CCR Mk 1 or Mk 2.

1.2 Limitations Any modification or deviations not explicitly approved by these regulations are strictly prohibited unless given permission by PASAB through sanction of the NEZ Racing Commission, who sanctions or ratifies further modifications or deviations. A permitted modification must never lead to an unauthorized modification. The only sanctioned changes that are allowed are normal adjustments, service and replacement of damaged parts. These parts may only be replaced by homologated CCR Mk1 or Mk2 parts according to appendix 1.1 Chevrolet Camaro, appendix 1.2 Ford Mustang, appendix 1.3 Dodge Challenger. Damaged parts on body or body parts, paint and decals must be repaired and/or replaced as soon as possible after the race.

1.3 References Some paragraphs in this document refer to the Technical Regulations (TR) of the Swedish ASN (SBF), which can be downloaded from www.sbf.se > Racing > Regler > Tekniska regler TR. 2 Homologation These regulations are based on CCR Mk1 or Mk2 Work Shop Manual and on spare parts homologated by PASAB according to appendix 1.1 Chevrolet Camaro, appendix 1.2 Ford Mustang, appendix 1.3 Dodge Challenger. 3 Oversight of Regulations Oversight of these regulations are made according to the regulations of the SBF. Interpretations of these regulations shall be made in consultation with the Racing Commission/Technical Committee of the SBF together with PASAB.


4 Weight Limits Minimum weight including driver, 1215 kg. In case ballast is used it must be placed in the intended ballast box. Provisions for the ballast to be sealed has to be made. Minimum weight refers to the weight of the car during practice, qualification or race including the driver. The car can be ordered in for weighing any time before, during or after practice, qualification or race and must comply with the minimum weight. All Gen.6 body´s (Camaro & Mustang) must mount two ballasts (Total 12Kg) according to below pictures, for compensation of lighter body weight. They should be sealed by technical stewards. Those ballasts are specified in Appendix 1.1, 1.2

5 General 5.1 Engine The only engine allowed is the LS3CC manufactured by GM Power Train. PASAB is the exclusive supplier of this engine. The engines are sealed. No work which requires the seal to be broken is allowed on the engines. If any seals from PASAB/Ultra Motors is missing from an engine, the competitor will be excluded from the current championship. Competitors are responsible for all seals. Valve cover is not sealed. Ultra Motors in Södertälje, Sweden, and Minges Universialservice in Trögstad, Norway are the official engine service suppliers and the only parties allowed to renovate, repair or serve these engines. Ultra Motors are responsible for engines from the Swedish, Finnish and Danish markets, Minges Universialservice are responsible for engines from the Norwegian market.

Only fully synthetic engine oil with a viscosity of 5W-30 and in accordance with the following standard, API SN, ILSAC GF5 may be used.

Spare engine will be supplied by PASAB in Sweden.

Unregulated parts:

Starting engine. Clutch cover. Throwout bearing. (Release bearing)


Spark plugs. Ignition cables. Oil filter. Safety Wire for Oil Plugs:

A through-hole may be drilled in the oil plugs to allow a safety wire to be used according to image below:

Engine Management (ECM)

The original GM LS3CC is the only Electronic Control Modul (ECM) allowed. The ECM is sealed. Connecting to, or up- or downloading information is prohibited. Only the white original cable from the ECM may be connected to the tachometer. The OBD-connection is sealed.

Any alteration of the ECM is prohibited.

Official technicians/stewards has free access to the ECM of each competitor/car.

Official technicians/stewards are authorized to:

• exchange ECM units between competitors/cars.

• check the software of the ECM.

• break the seal of an ECM and to reseal it after trouble shooting the unit. 5.2 Electrical System Battery Optima model 34/78. PN 8004-250 Red Top Starting. Laptimer may be installed Transponder must be fixed to the right front frame tube in pre-drilled holes. The original instruments must not be removed. Digital meters (of dash/datalogging type) can be installed.


Negative battery cable must be connected to the central ground connection of the car. The positive battery cable must be connected to the ignition switch. Observe! All wiring must be routed through the prefabricated entry system of the chassis, no new holes may be made. The only sensors allowed to be connected to dash/datalogging system are: G-force sensor. Sensor to measure interior temperature of driver compartment must be installed inside loggerbox. Voltage sensor (Volt) Engine revolution sensor. Wheel speed sensor (a maximum of one sensor) fixed to left front wheel. Lap Time sensor. Oil pressure and oil temperature sensor. Engine coolant temperature sensor. Lambda sensor. Fuel pressure sensor. GPS module. 5.3 Exhaust System Headers and Y-pipes CCR Mk1/ CCR Mk2 according to appendix 1.1, 1.2 and 1.3 CAMCUP13 Muffler system Ferrita. CAM09001 Catalyctic converter Ferrita. H2111C Exhaust tail pipe only, old version, only applicable outside Sweden. Noise level limit 95db (Only applicable in Sweden) according to Technical Regulations (TR4) of the SBF. If noise level (db) differs between countries. The rule is to follow hosting countries noise level (db), were race event take place. Thermal wrap may be fixed to the exhaust system at the two following points: To lessen the heat radiation on the generator thermal wrap may be installed on the front part of exhaust pipe 1 according to image 1 below:

Image 1

In order to decrease the heat radiation on Rear axle and fuel tank, thermal wrap may be installed according to new image 2 below:


Image 2

To prevent the heat radiation from the exhaust pipes on the generator cool air is allowed to be directed to the generator according to image 3 below. The following parts must be used for this purpose: PN RE200 Air Naca Duct and PN RE2031 Air Hose.

Image 3

5.4 Mounting of Front to Front Fenders Original mounting parts between the front and the fenders may be replaced. Mounting parts are free of regulation with the following exceptions: Mounting parts must be mounted, screwed or riveted in the original fiberglass/plastic edge on front and fender. No mounting parts must be installed from the outside of front and fenders. 5.5 Fuel According to V8 Thunder Cars NEZ Sporting Regulations. 5.6 Upper A-Frame Mounting To mount PN 2213907 (Precision Max Upper A-Frame) to the chassi the bolted joint must consist of bolt, washer + washer and a metal locknut: Bolt: UNC ½” x 2 ½”. Locknut UNC ½”, thread depth 7/16 (11mm). Steel washer t = 3/32” (2,38mm). The width of the sum of mounted Camber shims must not exceed 16,1 mm.


6 Transmission 6.1 Gearbox Four speed G-Force PN GF4A - G101A Gearing: 1st = 2,45:1 2nd = 1,57:1 3rd = 1,22:1 4th = 1,00:1 Reverse = 1,93:1 6.2 Shifter Mechanism Shifter Mechanism is free of regulation but must have an H-shifting pattern and fit in the original opening of the transmission tunnel. 6.3 Rear Axle Model CCR Mk1-Winters, according to appendix 1.1, 1.2,1.3. Type “Ford 9”. Gearing 3.50:1 Differential: Quaife ATB. Toe and camber may be adjusted according to the following: Toe = to a maximum of +/- 2 mm for each side Camber = to a maximum of + / - 0,3 degrees. 6.4 Drive Shaft Aluminum: PN QM188395 Steel: PN 243950 6.5 Master Cylinder The following parts from Howe and Tilton may be used without limitations: Howe PN 524312, Howe PN 524314, Howe PN 524316, TLT PN 74-875, TLT PN 74-1000.


6.6 Clutch Cover Complete clutch cover, certified by SFI. All included parts to the clutch cover must be installed. The clutch cover may be modified according to the images below, trimmed at the bottom of the sheet in order to raise the clearance of the car; elliptic holes at the edge of the center hole of the clutch cover may be made according to the yellow markings on the image in order to simplify disassembly/assembly the gearbox when a fixed release bearing is installed. No other modifications than those presented below are allowed.

. 7.0 Wheels 7.1 Rims Dimension maximum 9 x 17. Minimum offset ET35. Must be made of metal with exception of magnesium. The hub must not extend beyond the outer rim edge. A longer wheel bolt may be used for the front rim hubs. Replace the front wheel bolt PN 20612 with the longer rear wheel bolt, PN 20613. 7.2 Tires According to V8 Thunder Cars NEZ Sporting Regulations 8.0 Brakes Original CCR Mk1/Mk 2 according to appendix 1.1, 1.2, 1.3 The brake pad wear may be compensated by inserting shims between the backside of the brake pad and the brake caliper cylinder. Manufacturing and design of the shims are not regulated but they must be made of steel or aluminum. The material in the brake shields RE221R/RE221L may be reduced by the two following alternative methods presented in the image below: Alternative 1: Drill 3 holes with a diameter of 30 mm.


Alternative 2: Remove material inside the red line. Measured from the outer edge of the brake shield to the inner edge of the horizontal line, the radius is 50mm.

To decrease the heat radiation from exhaust to the brake and clutch fluid reservoirs PN B9524 may be installed according to the image below.

8.1 Front Brake Discs Original CCR Mk1/Mk2 + New 2018 AP disc, according to appendix 1.1, 1.2, 1.3 8.2 Rear Brake Discs Original CCR Mk1/Mk2 + Use old front disc rear, according to appendix 1.1, 1.2, 1.3 8.3 Brake Pads Not regulated 8.4 Brake Cylinder The following brake cylinders from Howe and Tilton may freely be shifted between front and rear brake circuit: Howe PN 524312, Howe PN 524314, Howe PN 524316, TLT PN 74875, TLT PN 74-1000.


8.5 Update Kit – Brakes Original CCR Mk1/Mk2 according to appendix 1.1, 1.2, 1.3 New PF140 brake kit valid from 2018 according to appendix 1.1, 1.2, 1.3

9.0 Chassis/Body 9.1 Minimum Heights Splitter minimum height measured from lower edge to level surface = 40mm. Area of measurement = Between the fixation points on the two outer adjustable struts of the splitter and between the two longitudinal angle bars mounted in the splitter. The crossbraces are mounted in these angle bars. See images below.

Minimum frame height measured from lower edge of side rail to level surface = 58mm. Area of measurement = A 100mm area measured from the front edge of the outer side rail. Measurements must be made on a level surface with the driver inside the car. Measurements may be made anytime during a race weekend. The height shall be measured with a minimum tire pressure of 1,5kg. 9.2 Steering Wheel Not regulated but CCR Mk1/Mk2 Steering Wheel hub WQRS must be used. A ”master key” slot may be made in wheel hub and the steering column. 9.3 Seat Seat according to the SBF Technical Regulation TR 5.16. Mounting bracket between seat and adjustable undercarriage according to the SBF Technical Regulation TR 5.16. The adjustable undercarriage (sliding seat) may be removed. The original mounting holes in the floor must be used and must not be altered or modified. 9.4 Foot Rest An individually adapted foot rest may be installed in the floor panel with pop rivet. 9.5 Chassis and Body Heat treating or straightening of main frame may only be made by PASAB or by companies approved by PASAB. Approved companies published by bulletin. The bumpers fixed with


bolts may be straightened and welded but original shape, dimensions and material must be preserved. Chassis- and bodyparts may only be replaced with original CCR Mk1/Mk 2 parts according to appendix 1.1, 1.2, 1.3. Two (2) hood vents, PN B940, may be installed on the hood. The following decals must be fixated and may not be altered: Grill/Front decal PN PF024 = Camaro. Grill/Front decal PN MUSTHLD = Mustang Grill/Front decal PN CHAHLD = Challenger Grill/Front decal PN 81131-44141 = Camaro Gen.6 Grill/Front decal PN 81321-44141 = Mustang Gen.6 Rear Light decal PN PF025, PF026 = Camaro Rear Light decal PN MUSTLDR, MUSTLDL, MUSTCAP = Mustang Rear Light decal PN CHATLD = Challenger Rear Light decal PN 81131-44541 = Camaro Gen.6 Rear Light decal PN 81321-44541 = Mustang Gen.6 9.6 Shock Absorbers Front: Öhlins type CAX - 971 Rear: Öhlins type CAX - 972 Öhlins Auto Norden, Dagvindsgatan 10, 652 22 Karlstad, is the exclusive supplier of shock absorbers and springs. Service and sealing may only be made by the above mentioned company. The two sealings below are approved along with the yellow paint sealing of the nut. The yellow paint seal together with one of the two seal alternatives must always be unbroken

9.7 Springs Front Spring: Öhlins 01092-79 = 190N/mm Front Spring: Öhlins 01092-89 = 210N/mm Front Spring: Öhlins 01092-91 = 230N/mm Front Helper Spring: Öhlins 05173-07 or 05173-01/KH. Must be installed. Front Spring Support: 05281-01 (53/74/19). Must be installed.


Rear Spring: Öhlins 00698-06 = 44N/mm Rear Spring: Öhlins 00698-14 = 60N/mm 9.8 Front Anti-Roll Bar SC1449HW112 = 1-1/2” according to appendix 1.1, 1.2, 1.3. SC1449HW138 = 1-3/8” according to appendix 1.1, 1.2, 1.3. SC1449HW114 = 1-1/4” according to appendix 1.1, 1.2, 1.3. Must not be decoupled. 9.9 Rear Anti-Roll Bar Original delivered with car, dimension = 19mm (3/4”). May be decoupled.

10 Safety Equipment 10.1 Roll Cage Certified chassis model CCR Mk1 / CCR Mk2 according to appendix 1.1, 1.2, 1.3. All tubing within a radius of 50 cm of the head of the driver (measurement made with driver belted in seat) shall be covered with FIA homologated flame resistant cushion for protection. 10.2 Safety Belt Six-point harness compulsory. According to the SBF Technical Regulation TR 5.6. 10.3 Fire Extinguisher Sparco model 0146EM41A with extinguishing agents for regular petrol. Lifeline model L-102-400-001 with extinguishing agents for regular petrol. The system must be in active mode (defined as possible to activate without removing any safety pins) during practice, qualification and race to the time for parc-fermé has expired or the car is released to the team. 10.4 Safety Fuel Cell Original CCR Mk1/Mk2 according to appendix 1.1, 1.2, 1.3. 10.5 Defuelling of Fuel Cell/ Fuel Sample System FIA PN: Name:

SPT 08.5655/L/JV Stäubli, panel mounted plug.

SPT08.1655/L/JV Stäubli, Female.

The drain plug must be placed in the aluminum sheet by the fuel cap according to the image below on Gen.5 models:


Fuel Sample. To protect ECM electric wire should be disconnected at tank armature. Electrical wire with switch from battery connects to tank armature and control fuel pump directly. After defueling reconnect electric wire from ECM.

The drain plug must be placed in engine bay according to the image below on Gen.6 models:

10.6 Other Safety Regulations Unless specified otherwise in these regulations, the Technical Regulations of SBF TR 5 supersedes these regulations. On Mustang Gen.5 the field of view is limited with regards to using the left rear view mirror. PN 15175-A31 may be replaced with PN 22548 Longacre. 11 Appendixes 11.1 Appendix 1.1 Homologated spare parts including part numbers for Chevrolet Camaro Gen.5 – Gen.6 11.2 Appendix 1.2 Homologated spare parts including part numbers for Ford Mustang Gen.5 – Gen.6


11.3 Appendix 1.3 Homologated spare parts including part numbers for Dodge Challenger Gen.3

1

NEZ Appendix 1.1 Chevrolet Camaro Gen.5 – Gen.6 CCR Mk1/Mk2 homologated parts and part descriptions.

P.N. Description LS3CC LS3CC engine E1599 Dry Sump Oil Tank

24255748 Pressure plate & Disc GF4A Transm. GF4A/G101A Special 10702P Frame & Cage Assembly, Perimeter 35803 Front Frame, Camaro Cup 36610 Tail Section B890 Aluminum Interior Incl Heat Shields 342508 Radiator Duct Work Kit-RR LS3CC 342518 Radiator Duct Work Kit Camaro + Mustang Gen.6

82120CAM Front Bumper Kit, Camaro, includes hood support 8212000 Front Bumper Camaro + Mustang Gen.6

8212100 Front Bumper Hood pin bar Camaro Gen.6

82220CAM Rear Bumper Kit, Camaro 8222200 Rear Bumper Camaro Gen.6

SCA827 Collapsable Steering Shaft WQRS Steering quick release.

HE-236 Rack, Woodward Power 17.25" Threaded, .220 t/b, 955 valve, 1.5" cylinder

PF046 Rack limiter plate 14720 Rack Spacer 1/4" 14730 Rack Spacer 3/8" T40S P/S Pump Howe

PS2005 P/S Pump pulley Howe

PS3005 P/S Pump bracket Howe

KRC63200000 P/S Pump Evolution Alum. KRC20002000 P/S Pump Alum. KRC20020650 P/S Pulley LS3CC KRC71410040 P/S Bracket LS3CC PS8302 Power Steering Hose Kit W/Cooler PS501 Power Steering Tank W/Bracket R3315 Sleeve 5/8”x15” Hex Alum. 23285 Tie rod 5/8”-18 LH Inside 23286 Tie rod 5/8”-18 RH Outside 23297 Tie rod inner stud 23298 Tie rod outer stud 31491 Bolt Kit suspension

2

22320 Ball Joint, Precision Upper 22330 Ball Joint, Stud Only Upper 2213907 Precision Max Upper A-Frame 9.75" 22001 Upper A-Frame Key Kit 60203 A-frame Shims 1/8” 60204 A-frame Shims 3/16” 60205 A-frame Shims ¼” 60206 A-frame Shims 3/8” 60207 A-frame Shims ½” 60210S A-frame Shims Kit 229617C Lower control arm 22410 Ball Joint, Precision Lower 22430 Ball Joint, Stud Only Lower AU-AM12T Rod end ¾” RH male 22949 Strut arm rod end angled AU-AB12T Rod end ¾” LH male 346104 Spindle, Right 5X5 34610L4 Spindle, Left 5X5 SC1449HW114 Sway bar 1-1/4" SC1449HW138 Sway bar 1-3/8" SC1449HW112 Sway bar 1-1/2" 23925 Bushing Delron for splined swaybar 23926 Swaybar arm Left 23927 Swaybar arm Right 23611 Rear Sway Bar Kit 31180 Panhard Axle Mount Rear Ford 9” 31990 Axle clamp, special for 3” tube 30786 Panhard Assembly 30780 Panhard Mount, Frame 3252 Axle Stops 32009 Winters 9” third link bracket 20613 Wheel Studs rear PF059 Brake uppgrade kit MK2 front. Parts below marked *

36571 Front hubs 5x4,75, Steel Mk2 * 20536 Hub dust cover Mk2 * 20573 Brake rotor hat * 36574 T-nuts for hat * 300-0802 Bolt for T-nut * 36573G Hans cooling gasket * SRS800 Brake blower fan new

SRS801 Brake blower fan adapter new

SRS400 Brake blower fan * Out of production.

3

SRS002 Fan blower replacemnt

SRS004 Engine fan blower replacement

CAMSCRMK2 Nose Screen, Camaro 2013 *

RE308 Brake cooler nose air duct right *

RE308L Brake cooler nose air duct left *

RE2034 Brake Hose 4,5” Length 14” *

RE2031 Brake air hose-12`length (4m) *

RE31000 Brake Air duct box Right Camaro + Mustang Gen.6

RE31000L Brake Air duct box Left Camaro + Mustang Gen.6

RE31000SCR Brake Screen Camaro + Mustang Gen.6

B941L Brake fan mount Left Pro syst *

B941 Brake fan mount Right Pro syst *

205500 Front Hubs, 5X4.75, Steel Mk1 20538 Hub Dust Cover Mk1 205700 Rear Hubs 5x4,75 Steel 20547 Drive flange 9” ALL44122 Wheel spacer 9” TG3001-33 Axle gundrilled Left 33”

TG3001-37 Axle gundrilled Right 37”

RV102 Rear end vent assy 9” KN62-1460 Filter for vent tank 32258 Axle tube seal 9”

QDR1 Quafie ATB Diff. CCRMK1/Winters Rear axle 9” W95590 Winters 9” housing with axle tubes WA94303 Winters 9” center section HUR114-7494 Shift Boot Hurst PM8182 Alternator 75A KRC8172 Alternator 50A 90-293-1630 Alternator 40A RE200 Naca duct single hole KRC40140640 Alernator pulley LS3CC GDY4060720 Drive belt LS3CC GDY4060725 Drive belt to T40S P/S pump

E113 Alternator bracket LS3CC E7015 ECM mount LS3CC PF062 GM ECM LS3CC E7016 Engine wire harness LS3CC 9026, 9027 Engine Skid Pan R100 Engine spacer ¼”

4

R1005 Engine spacer ½” E15910 Engine vent tank for valve covers LS3CC E1597 Oil filter block off line adapter LS3CC 82892 Hydr. Bearing line and bleed kit incl. coupler QM188395 Drive Shaft, Aluminum 39.5" QM188545 Drive Shaft, Yoke 243950 Drive shaft steel

280 U-Joint Serve Duty

329-10 Drive Shafts U-Bolts 9” 369YOKE Machined Yoke 36299, 36299L Motor mounts front LS3CC 3611 Motor Mounts, Left 3613 Motor Mounts. Right ATM2271 Water temp fitting at water pump 3/8” NPT LS3CC 58982 Rad. Hose reducer 1,75” to 1,5” LS3CC 58981 Rad. Hose reducer 1,5” to 1,25” LS3CC 342411 Vertical surge tank LS3CC 28474 ,75” Dia. 90° hose from surge tank to water pump LS3CC HRP90150 1,5” 90° blue hose LS3CC HRP45175 1,75” 45° blue hose LS3CC 34312 Rad. Hose connector 3,5” Long (1 of 1,5” dia.) LS3CC 34322 Rad. Hose connector 4” Long (1 of 1,75”) LS3CC 34129C10 Radiator, W/Oil Cooler 3427 Radiator Cap 3426 Spool thermostat replacement 34221 Radiator Hoses, Overflow Tank & Lines 342026 Upper Radiator Mount, Left 342027 Upper Radiator Mount, Right M162K Fan, electric 16” pull MFA104 Fan, mounting kit CAN22625 Remote Oil Filter Mount E3005 Engine Oil Filter Line Kit LS3CC E1599 Dry sump oil tank LS3CC E164 Dry sump oil tank mounting brackets and straps LS3CC E165 Dry sump oil tank heat shield LS3CC 50-625-7612 Engine Oil cooler in Air box 7,5”x11” LS3CC 22-M22AN10-SE Setrab Cooler fitting E166 Engine Oil cooler mount LS3CC GS1003-12 Seals It gasket

5

21044 SLP Air box LS3CC 25166571 Plastic GM filter mount LS3CC 25042562 Air filter GM/AC Delco E146 Alum.angle filter box mount LS3CC E7004 20° 3,5” elbow LS3CC E7003 3,5” to 4” Hose connector LS3CC E145 Air deflector LS3CC H11213C New headers LS3CC narrower chassi clearance LS3CC H2024C Y-pip LS3CC 3,5” to 3,5” LS3CC H2111C Exhaust tail pipe only, old version

B907 catalytic convertor heat shield H3032 Exhaust Hanger Centred Around catalytic Converter H3031 Muffler / Exhaust Hanger Rear H3028 Exhaust Hanger Rubber HPFC300 Stainless Exhaust band clamp 3” PF140 Brake Upgrade kit 2018. Below parts marked #

CP9660-3S4L AP Caliper, 6 Piston Front Left #

CP9660-2S4L AP Caliper, 6 Piston Front Right #

CCA029660-355 AP Caliper bracket. #

BCA0212x2286B Rotor hat (Bell) #

CP2494-589K12 Rotor bolt kit front #

FKCA029660 Fitting kit AP brakes #

120-6387-RS Wilwood Caliper, 6 Piston, Front. Out of production. 120-6388-RS Wilwood Caliper, 6 Piston, Front. Out of production. 120-8283L Wilwood Caliper, 4 Piston, Rear 120-8283R Wilwood Caliper, 4 Piston, Rear 120-11127 Wilwood Caliper, 4 Piston Rear L&R #

120-11125 Wilwood Caliper, 4 Piston. Rear L&R CCA0511127310 Caliper bracket #

340910 Cast clamp on bracket 9” B716SHCS Caliper bolts CP5772-1137RA Rotor, Directional Left. AP Front #

CP5772-1136RA Rotor, Directional Right AP Front #

CP1901727 Rotor, Directional Left, AP Front and Rear. CP1901726 Rotor, Directional Right, AP Front and Rear. CP1901782 Rotor, Directional RH AP Rear CP1901783 Rotor, Directional LH AP Rear B926 Brake Cooler plastic holder B931 Caliper cooler mount 3383219 Brake Line 21” w/90* fitting

6

338326 Brake Line 26” FBM2511 Brake Line Fitting 33791 Brake Line Fitting 80171 Painless Brake Light Switch RT-RD24 Tail Lights, 70 x 118 mm LED Aftermarket B925 Tail Lights bracket B92500 Tail Light bracket outer Camaro Gen.6

B92500I Tail Light bracket Inner Camaro Gen.6

TLT74-875 Master Cylinder 7/8” TLT74-1000 Master Cylinder 1” TLT74-200 Fitting Plastic

TLT74-208 Master Cyl. Clamp

524312 Master Cylinder, Remote Reservoir 3/4” 524314 Master Cylinder, Remote Reservoir 7/8” 524316 Master Cylinder, Remote Reservoir 1” 524312K Master Cyl. O-ring repair ¾” 524314K Master Cyl. O-ring repair 7/8” 524316K Master Cyl. O-ring repair 1” AU12685 Master Cylinder Hose Clamp RD109 Master Cylinder Hose 5/16” 524353 Master Cylinder Fitting B9524 Master Cyl. Reservoir Heat Shield CP0805420 Master Cylinder Reservoir, Double Port CP0805424 Master Cylinder Reservoir, Single Port CP2293-48 Bellows for Master Cylinder Reservoir 524361 Master Alum. Cyl. Reservoir Double port

524360 Master Alum. Cyl. Reservoir Singel port

33814 Braided #4 line


BR11078 1/8 npt to 3/16 inverted flare 90* WW260-1874 Residual Valve 2# 52692 Pedal, Brake Floor Mounted 52992 Pedal, Clutch Floor Mounted 52591 Clutch Pedal Stop 5299 Dead Pedal WW340-4990 Brake Bias Adjuster 72560 90* Bias Adjuster TC1000LS1 Throttle Cable LS3CC 52502 Engine mount for throttle cable LS3CC 5237 Pedal, Gas

7

52351 Throttle Stop OP-11B Fuel Cell bracket 13202 Fuel Filler 13202B Fuel Filler bracket RE103 Fuel Filler neck top mount Camaro + Mustang Gen.6

RF102 Fuel hose clear 2-1/4”

RF215 Fuel Line Kit LS3CC RUS644120 Fitting for fuel rail inlet LS3CC PC122F-EFI Fuel cell w/internal pump LS3CC PC122F-B Fuel Cell Bladder

HP2010 Fuel filter LS3CC HP1200 Fuel filter replacement LS3CC HP2010B Fuel filter mount LS3CC FSC1 Fuel Safe pump in tank kit LS3CC FPHP El. Fuel pump LS3CC 9120 battery heat shield E5495 Battery shut off switch 4 post

MOR74102 Battery shut off switch 4 post 300 Amp.

RRCWH Chassis Wiring Harness E4407T Guage Panel, W/Tach E3316 Fuel Level Guage KS210-10 Fuel Level Sender E3563 Fuel Pressure Gauge LS3CC B902CC Switch Panel W/Accessory B902LCC Switch Panel Cover B908 Dash panel cover plate B913 Dash panel cover plate spacer B914 Defogger Diffuser Box B9140 Defogger blower bracket RE195 Defogger Fan B930 Ignition mounting plate RF125A Heat Shield, Extreme Temperature RF126A Heat Shield, Standard Grade RF127A Roll Aluminum Sealant Tape B915 Heat Shield Behind Driver Seat B80190 Windsheild Tear off B80191 Windsheild Tear off Camaro + Mustang Gen.6

65030 Roll Bar Padding BCS155601 Roll Bar Padding FIA Type A

8

465-1004 ¼” Cable clamps 465-1006 3/8” Cable clamps 465-1014 1” Cable clamps 22534 Rearview Mirror 81131-106 Body, Camaro 2016 Gen.6,Incl. Front & Rear Windows.

81131-31013 Deck Lid

81131-21013R Door Right

81131-21713L Door Left Upper Gen.6

81131-21813L Door Left Lower Gen.6

81131-45012 Bumper cover rear

81132-41212 Nose, upper

81002-41112 Nose. Lower

81132-23013R Fender right front

81132-23013L Fender left front

81131-51312 Greenhouse section front

81131-51512 Greenhouse section rear

81131-33012 Hood

81132-27313R Quarter panel right

81132-27313L Quarter panel left

81131-65243R Windows quarter right

81131-65243L Windows quarter left

81131-61243 Window rear

81131-63343 Window front

81131-76333 Windsheild brace Gen.6

81131-76133 Window brace rear Gen.6

81131-44541 Decal Tail light Gen.6

81131-44141 Decal Nose Gen.6

81001-46433B Nose Screen Camaro + Mustang Gen.6

407500 Rocker Panel Right Gen.6

407600 Rocker Panel Left Gen.6

B92100 Vent Window Right Gen.6

B92200 Vent Window Left Gen.6

B92800 Window brace bracket R + L Gen.6

CAM2010 Body, Camaro 2010 Includes Front & Rear Windows. 40035 Left side opening door mechanism “Safety opening” 40036 Left side opening door hardware B1017 Hood Pins, Pair, CAMSCR Nose Screen, Camaro 2010 CAMDLB Deck Lid Bracket and Hinge Assy, Camaro

9

AS-105552 V-SPEC Wing AA-100038 Wing sideplate carbon B917 Splitter B917M16 Splitter Camaro + Mustang Gen.6

B9171 Splitter Pinch plate B918 Splitter brace FS807-3 Splitter adj. braces PF050 Upper brake light Led PF024 Decal Camaro head light and front grill PF025 Decal Camaro rear light right PF026 Decal Camaro rear light left CAMIFL Extended Inner Fender behind front tire Left CAMIFR Extended Inner Fender behind front tire Right CAMBB Front and Rear Roof Support Brackets 4001 Window Net 40020 Window Net mount lower

40025 Latch Bar to net

WM KIT AFI Wiper Kit AM2301353 Wiper motor to AFI

AM3022160 Wiper blade to AFI

B904CC Window Ledge Right FS805 Window Installation Kit B800C Window Braces B800CR Window Brace rear B1017A Trunk Fasteners, Pair PF027 Tow Straps 9020 Tow Hook Camaro + Mustang Gen.6

PF045 Tow decal B927 Jack post plate B928 Window brace bracket B929 Exhaust exit flange plate B9205C Side view mirror right

B9195C Side view mirror left

B91900 Mirror Spacer left to fit B9195C on Gen.6

B92000 Mirror Spacer right to fit B9205C on Gen.6

919 Mirror bracket left side B920 Mirror bracket right side 90181 Ready made body mounts 90182 Ready made body mounts

10

B940 Lowers on Hood. 4011CAM Hood, Camaro 4015CAM Trunk, Camaro 4040CAM Quarter Panel, Right, Camaro 4041CAM Quarter Panel, Left, Camaro 4042CAM Rear Cover, Right, Camaro 4043CAM Rear Cover, Left, Camaro 4044CAM Rear Cover, Center Diffuser, Camaro B422W Nose Plastic Camaro Right + Left 4072CAM Fender, Right, Camaro 4073CAM Fender, Left, Camaro 4080CAM Door, Right, Camaro 4081CAM Door, Left, Camaro 40810CAM Door, Left Camaro Lower 40815CAM Door, Right Camaro Upper 40820CAM Roof, Rear Section, Camaro 40821CAM Tray, Rear Window, Camaro 4082CAM Roof, Front Section, Camaro B8019 Front Window, cut, drilled and Blackout. B923 Rear Window, cut, drilled and Blackout. B921 Quarter Window, R/S B922 Quarter Window, L/S B924 Quarter Panel Brace B932 Upper Hood support Right.

B93200R Upper Hood support Right Gen.6

B932L Upper Hood support Left.

B93200L Upper Hood support Left Gen.6

0146EM41A Fire exthinguiser L-102-400-001 Fire system Life Line

493 Sliding rail ALL14190 Ballast Stud & Nut. Only to Camaro + Mustang Gen.6

ALL14197 Ballast Bracket. Only to Camaro + Mustang Gen.6

PF129 Ballast Round Bar. Only to Camaro + Mustang Gen.6

Part numbers may be changed. Changes will be notified by bulletins.

1

NEZ Appendix 1.2 Ford Mustang Gen.5 – Gen.6 CCR Mk1/Mk2 homologated parts and part descriptions.

P.N. Description LS3CC LS3CC engine E1599 Dry Sump Oil Tank

24255748 Pressure plate & Disc GF4A Transm. GF4A/G101A Special 10702P Frame & Cage Assembly, Perimeter 35803 Front Frame, Camaro Cup 36610 Tail Section B890 Aluminum Interior, Incl Heat Shields 342506 Radiator Duct Work Kit-RR Mustang 342518 Radiator Duct Work Kit. Mustang + Camaro Gen.6

82120M Front Bumper Kit, Mustang, includes hood support 8212000 Front Bumper Mustang + Camaro Gen.6

8212101 Front Bumper Hood Pin bar Gen.6

82220M Rear Bumper Kit, Mustang 8222202 Rear Bumper Gen.6

SCA827 Collapsable Steering Shaft WQRS Steering quick release

HE-236 Rack, Woodward Power 17.25" Threaded, .220 t/b, 955 valve, 1.5" cylinder

PF046 Rack limiter plate 14720 Rack Spacer 1/4" 14730 Rack Spacer 3/8" T40S P/S Pump Howe



KRC63200000 P/S Pump Evolution Alum. KRC20002000 P/S Pump Alum. KRC20020650 P/S Pulley LS3CC KRC71410040 P/S Bracket LS3CC PS8302 Power Steering Hose Kit W/Cooler PS501 Power Steering Tank W/Bracket R3315 Sleeve 5/8”x15” Hex Alum. 23285 Tie rod 5/8”-18 LH Inside 23286 Tie rod 5/8”-18 RH Outside 23297 Tie rod inner stud

2

23298 Tie rod outer stud. 31491 Bolt Kit suspension 22320 Ball Joint, Precision Upper 22330 Ball Joint, Stud Only Upper 2213907 Precision Max Upper A-Frame 9.75" 22001 Upper A-Frame Key Kit 60203 A-frame Shims 1/8” 60204 A-frame Shims 3/16” 60205 A-frame Shims ¼” 60206 A-frame Shims 3/8” 60207 A-frame Shims ½” 60210S A-frame Shims Kit 229617C Lower control arm 22410 Ball Joint, Precision Lower 22430 Ball Joint, Stud Only Lower AU-AM12T Rod end ¾” RH male 22949 Strut arm rod end angled AU-AB12T Rod end ¾” LH male 346104 Spindle, Right 5X5 34610L4 Spindle, Left 5X5 SC1449HW114 Sway bar 1-1/4" SC1449HW138 Sway bar 1-3/8" SC1449HW112 Sway bar 1-1/2" 23925 Bushing Delron for splined swaybar 23926 Swaybar arm Left 23927 Swaybar arm Right 23611 Rear Sway Bar Kit 31180 Panhard Axle Mount Rear Ford 9” 31990 Axle clamp, special for 3” tube 30786 Panhard Assembly 30780 Panhard Mount, Frame 3252 Axle Stops 32009 Winters 9” third link bracket 20613 Wheel Studs rear PF059 Brake upgrade kit MK2 front. Parts below marked *

36571 Front hubs 5x4,75 Steel mk2 * 20536 Hub dust cover mk2 * 20573 Brake rotor hat * 36574 T-nuts for hat * 300-0802 Bolt for T-nut *

3

36573G Hans cooling gasket * SRS800 Brake blower fan new.

SRS801 Brake blower fan adapter new.

SRS400 Brake blower fan * Out of production

SRS002 Fan blower replacement

SRS004 Engine fan blower replacemant

RE307 Brake duct inlet box right *

RE307L Brake duct inlet box left *

RE307Det1 Brake duct inlet 4,5” hose & 3” hose *

RE2034 Brake air hose 4,5” Length 14” *

RE2031 Brake air hose 3”, 12` length (4m) *

RE31000 Brake Air duct box Right Mustang + Camaro Gen.6

RE31000L Brake Air duct box Left Mustang + Camaro Gen.6

RE31000SCR Brake Screen Mustang + Camaro Gen.6

B941L Brake fan mount Left Pro syst. *

B941 Brake fan mount Right Prio syst. *

205500 Front hubs 5x4,75” Steel Mk1 20538 Hub dust cover Mk1 205700 Rear Hubs 5x4,75 Steel 20547 Drive flange 9” 44122 Wheel spacer 9” TG3001-33 Axle gundrilled Left 33”


RV102 Rear end vent assy 9” KN62-1460 Filter for vent tank 32258 Axle tube seal 9”

QDR1 Quafie ATB Diff. CCRMK1/Winters Rear axle 9” W95590 Winters 9” housing with axle tubes WA94303 Winters 9” center section HUR114-7494 Shift Boot Hurst PM8182 Alternator 75A KRC8172 Alternator 50A 90-293-1630 Alternator 40A RE200 Naca duct single hole KRC40140640 Alernator pulley LS3CC GDY4060720 Drive belt LS3CC GDY4060725 Drive belt to P/S pump T40S

4

E113 Alternator bracket LS3CC E7015 ECM mount LS3CC PF062 GM ECM LS3CC E7016 Engine wire harness LS3CC 9026, 9027 Engine Skid Pan R100 Engine spacer ¼” R1005 Engine spacer ½” E15910 Engine vent tank for valve covers LS3CC E1597 Oil filter block off line adapter LS3CC 82892 Hydr. Bearing line and bleed kit incl. coupler QM188395 Drive Shaft, Aluminum 39.5” QM188545 Drive Shaft, Yoke 243950 Drive shaft steel


329-10 Drive Shafts U-Bolts 9” 369YOKE Machined Yoke 36299, 36299L Motor mounts front LS3CC 3611 Motor Mounts, Left 3613 Motor mounts, Right ATM2271 Water temp fitting at water pump 3/8” NPT LS3CC 58982 Rad. Hose reducer 1,75” to 1,5” LS3CC 58981 Rad. Hose reducer 1,5” to 1,25” LS3CC 342411 Vertical surge tank LS3CC 28474 ,75” Dia. 90° hose from surge tank to water pump LS3CC HRP90150 1,5” 90° blue hose LS3CC HRP45175 1,75” 45° blue hose LS3CC 34312 Rad. Hose connector 3,5” Long (1 of 1,5” dia.) LS3CC 34322 Rad. Hose connector 4” Long (1 of 1,75”) LS3CC 34129C10 Radiator, W/Oil Cooler 3427 Radiator Cap 3426 Spoole Thermostat replacement 34221 Radiator Hoses, Overflow Tank & Lines 342026 Upper Radiator Mount, Left 342027 Upper Radiator Mount, Right M162K Fan, electric 16” pull MFA104 Fan, mounting kit CAN22625 Remote Oil Filter Mount

5

E3005 Engine Oil Filter Line Kit LS3CC E1599 Dry sump oil tank LS3CC E164 Dry sump oil tank mounting brackets and straps LS3CC E165 Dry sump oil tank heat shield LS3CC 50-625-7612 Engine Oil cooler in Air box 7,5”x11” LS3CC 22-M22AN10-SE Setrab cooler fitting E166 Engine Oil cooler mount LS3CC GS1003-12 Seals IT gasket 21044 SLP Air box LS3CC 25166571 Plastic GM filter mount LS3CC 25042562 Air filter GM/Ac Delco E146 Alum. Angle filter box mount LS3CC E7004 20° 3,5” elbow LS3CC E7003 3,5” to 4” Hose connector LS3CC E145 Air deflector LS3CC H11213C New headers LS3CC narrower chassi clearance H2024C Y-pip LS3CC 3,5” to 3,5” LS3CC H2111C Exhaust tail pipe only, old version

B907 catalityc convertor heat shield H3032 Exhaust Hanger Center Around catalytic Converter H3031 Muffler / Exhaust Hanger Rear H3028 Exhaust Hanger Rubber HPFC300 Stainless Exhaust band clamp 3” PF140 Brake upgrade kit 2018. Below parts marked #



CCA029660-355 AP Caliper bracket #




120-6387-RS Wilwood Caliper, 6 Piston, Front. Out of production. 120-6388-RS Wilwood Caliper, 6 Piston, Front. Out of production. 120-8283L Wilwood Caliper, 4 Piston, Rear 120-8283R Wilwood Caliper, 4 Piston, Rear 120-11127 Wilwood Caliper, 4 Piston, Rear L&R #


6

340910 Cast clamp on bracket 9” B716SHCS Caliper bolts CP5572-1137RA Rotor, Directional Left AP Front #

CP5772-1136RA Rotor, Directional Right AP Front #

CP1901727 Rotor, Directional Left, AP Front and Rear. CP1901726 Rotor, Directional Right, AP Front and Rear. CP1901782 Rotor, Directional RH AP Rear CP1901783 Rotor, Directional LH AP Rear B926 Brake Cooler plastic holder B931 Caliper cooler mount 3383219 Brake Line 21” w/90* fitting 338326 Brake Line 26” FBM2511 Brake Line Fitting 33791 Brake Line Fitting 80171 Painless Brake Light Switch RT-RD24 Tail Lights, 70 x 118 mm LED Aftermarket B925M Tail Light bracket B92501 Tail Light bracket Gen.6

TLT74-875 Master Cylinder 7/8” TLT74-1000 Master Cylinder 1” TLT74-200 Fitting Plastic

TLT74-208 Master cyl. Clamp

524312 Master Cylinder, Remote Reservoir 3/4” 524314 Master Cylinder, Remote Reservoir 7/8” 524316 Master Cylinder, Remote Reservoir 1” 524312K Master Cyl. O-ring repair ¾” 524314K Master Cyl. O-ring repair 7/8” 524316K Master Cyl. O-ring 1” AU12685 Master Cylinder Hose Clamp RD109 Master Cylinder Hose 524353 Master Cylinder Fitting B9524 Master Cyl. Reservoir heat 6hield CP0805420 Master Cylinder Reservoir, Double Port CP0805424 Master Cylinder Reservoir, Single Port CP2293-48 Bellows for Master Cylinder Reservoir 524361 Master Alum. Cyl. Reservoir Double port

524360 Master Alum. Cyl. Reservoir Singlw port


7


BR11078 1/8 npt to 3/16 inverted flare 90* WW260-1874 Residual Valve 2# 52692 Pedal, Brake Floor Mounted 52992 Pedal, Clutch Floor Mounted 52591 Clutch Pedal Stop 5299 Dead Pedal WW340-4990 Brake Bias Adjuster 72560 90* Bias Adjuster TC1000LS1 Throttle Cable LS3CC 52502 Engine mount for throttle cable LS3CC 5237 Pedal, Gas 52351 Throttle Stop OP-11B Fuel Cell bracket 13202 Fuel Filler RE103 Filler Neck Top mount Mustang + Camaro Gen.6

RF102 Fuel hose clear 2-1/4”

13202B Fuel Filler bracket RF215 Fuel Line Kit LS3CC RUS644120 Fitting for fuel rail inlet LS3CC PC122F-EFI Fuel cell w/internal pump LS3CC PC122F-B Fuel Cell Bladder

HP2010 Fuel filter LS3CC HP1200 Fuel filter replacement LS3CC HP2010B Fuel filter mount LS3CC FSC1 Fuel Safe pump in tank kit LS3CC FPHP El. Fuel Pump LS3CC 9120 battery heat shield E5495 Battery shut off switch 4 post

MOR74102 Battery shut off switch 4 post 300Amp

RRCWH Chassis Wiring Harness E4407T Guage Panel, W/Tach E3316 Fuel Level Guage KS210-10 Fuel Level Sender E3563 Fuel Pressure Gauge LS3CC B902CC Switch Panel W/Accessory B902LCC Switch Panel Cover

8

B908 Dash panel cover plate B913 Dash panel cover plate spacer B914 Defogger Diffuser Box B9140 Defogger blower bracket RE195 Defogger Fan B930 Ignition mounting plate RF125A Heat Shield, Extreme Temperature RF126A Heat Shield, Standard Grade RF127A Roll Aluminum Sealant Tape B915 Heat Shield Behind Driver Seat B80190 Windsheild Tear off B80191 Windsheid Tear off Mustang + Camaro Gen.6

65030 Roll Bar Padding BCS155601 Roll Bar Padding FIA Type A 465-1004 ¼” Cable clamps 465-1006 3/8” Cable clamps 465-1014 1” Cable clamps 22534 Rearview Mirror 81321-106 Body, Mustang 2016 Gen.6, Incl. Front & Rear windows.

81321-31013 Deck Lid

81321-21013R Door Right

81321-21713L Door Left Upper

81321-21813L Door Left Lower

81321-4501 Bumper Cover rear

81321-41212 Nose, upper

81001-41112 Nose, Lower

81322-23013R Fender right front

81322-23013L Fender left front

81321-51312 Greenhouse section, front

81321-51512 Greenhouse section, rear

81321-33012 Hood

81322-27313R Quarter panel right

81322-27313L Quarter panel left

81321-65243R Windows quarter right

81321-65243L Windows quarter left

81321-61243 Window rear

81321-63343 Window front

9

81321-76333 Windshield brace

81321-76133 Window brace rear

81321-44541 Decal Tail light

81321-44141 Decal Nose kit

81001-46433B Nose Screen Mustang + Camaro Gen.6

407501 Rocker Panel Right

407601 Rocker Panel Left

B92101 Vent Window Right

B92201 Vent Window Left

B92801 Window Brace Bracket L+R

4403 Body, Mustang 2013 ,Includes Front & Rear Windows. 40036 Left side opening door hardware MICP Interior crush panel conversion kit B1017 Hood Pins, Pair, MUSSCR Nose Screen, Mustang lower MUSSCRUPR Nose Screen, Mustang Upper MUSDLB Deck Lid Bracket and Hinge Assy, Mustang AS-105552 V-SPEC Wing AA-100038 Wing sideplate carbon B917M Splitter Mustang B917M16 Splitter Mustang + Camaro Gen.6

B9171 Splitter pinch plate

B918 Splitter brace FS807-3 Splitter adj. Braces PF050 Upper brake light Led MUSTHLD Decal Mustang head light and front grill MUSTLDR Decal Mustang rear light, right MUSTLDL Decal Mustang rear light, left MUSTCAP Decal Mustang gas cap

MUSIFL Extended Inner Fender behind front tire Left Mustang MUSIFR Extended Inner Fender behind front tire Right Mustang MUSBB Front and Rear Roof Support Brackets Mustang 4001 Window Net 40020 Window Net mount lower

40025 Latch bar to net.

WM KIT AFI Wiper Kit AM2301353 Wiper Motor to AFI

10

AM3022160 Wiper Blade to AFI

FS805 Window Installation Kit B800M Window Braces Mustang B800MR Window Brace rear Mustang B1017A Trunk Fasteners, Pair PF027 Tow Straps 9020 Tow Hook Mustang + Camaro Gen.6

P045 Tow decal B927 Jack post plate B928M Front Window brace bracket Mustang B929M Exhaust exit flange plate Mustang 15175-A32 Side view mirror right Mustang 15175-A31 Side view mirror left Mustang B9205M Side view mirror right Gen.6

B9195M Side view mirror left Gen.6

B91921 Mirror bracket L. Camaro mirror on Mustang gen.6

B92021 Mirror bracket R. Camaro mirror on Mustang gen.6

B91931 Mirror spacer L. Camaro mirror on Mustang gen.6

B92031 Mirror spacer R. Camaro mirror on Mustang gen.6

B9195C Side view mirror L. Camaro to Mustang gen.6 only.

B9205 Side view mirror R. Camaro to Mustang gen.6 only.

22549 Side view mirror left Nascar Mustang B919M Mirror bracket left side Mustang B920M Mirror bracket right side Mustang B932M Cowl support right Mustang B932ML Cowl support left Mustang B93201L Upper Hood support Left Gen.6

B93201R Upper Hood support Right Gen.6

90181 Ready made body mounts 90182 Ready made body mounts B940 Lowers on Hood 4011M Hood, Mustang 4015M Trunk, Mustang 4040M Quarter Panel, Right, Mustang 4041M Quarter Panel, Left, Mustang 4042M Rear Cover, Right, Mustang 4043M Rear Cover, Left, Mustang 4044M Rear Cover, Center Diffuser, Mustang

11

4045M Nose fiberglas R Mustang 4046M Nose fiberglas L Mustang 4072M Fender, Right, Mustang 4073M Fender, Left, Mustang 4080M Door, Right, Mustang 4081M Door, Left, Mustang 40810M Door Left Mustang Lower 40815M Door Left Mustang Upper 40820M Rear deck filler Mustang 4082M Roof front Mustang B8019M Front Window, cut, drilled and Blackout. Mustang B923M Rear Window, cut, drilled and Blackout. Mustang B921M Quarter Window, R Mustang B922M Quarter Window, L Mustang 493 Sliding rail 0146EM41A Fire Exthinguiser L-102-400-001 Fire system Life Line

ALL14190 Ballast stud & nut. Only to Mustang + Camaro Gen.6

ALL14197 Ballast bracket. Only to Mustang + Camaro Gen.6

PF129 Ballast round bar. Only to Mustang + Camaro Gen.6


12

NEZ Appendix 1.3 Dodge Challenger Gen.3 CCR Mk1/Mk2 homologated parts and part descriptions.

P.N. Description LS3CC LS3CC engine E1599 Dry sump oil tank

24255748 Pressure plate & Disc GF4A Transm. GF4A/G101A Special. 10702P Frame & Cage Assembly, Perimeter 35803 Front Frame, 36610 Tail Section B890 Aluminum Interior, Incl Heat Shields 342509 Radiator Duct Work Kit Challenger 82120D Front Bumper Kit, Challenger, includes hood support 82220D Rear Bumper Kit, Challenger. SCA827 Collapsable Steering Shaft WQRS Steering quick release

HE-236 Rack, Woodward Power 17.25” Threaded, .220 t/b, 955 valve, 1.5” cylinder

PF046 Rack limiter plate 14720 Rack Spacer 1/4” 14730 Rack Spacer 3/8” T40S P/S Pump Howe



KRC63200000 P/S Pump Evolution Alum. KRC20002000 P/S Pump Alum. KRC20020650 P/S Pulley LS3CC KRC71410040 P/S Bracket LS3CC PS8302 Power Steering Hose Kit W/Cooler PS501 Power Steering Tank W/Bracket R3315 Sleeve 5/8”x15” Hex Alum. 23285 Tie rod 5/8”-18 LH Inside 23286 Tie rod 5/8”-18 RH Outside 23297 Tie rod inner stud 23298 Tie rod outer stud 31491 Bolt Kit suspension 22320 Ball Joint, Precision Upper 22330 Ball Joint, Stud Only Upper 2213907 Precision Max Upper A-Frame 9.75” 22001 Upper A-Frame Key Kit

13

60203 A-frame Shims 1/8” 60204 A-frame Shims 3/16” 60205 A-frame Shims ¼” 60206 A-frame Shims 3/8” 60207 A-frame Shims ½” 60210S A-frame Shims Kit 229617C Lower control arm 22410 Ball Joint, Precision Lower 22430 Ball Joint, Stud Only Lower AU-AM12T Rod end ¾” RH male 22949 Strut arm rod end angled AU-AB12T Rod end ¾” LH male 346104 Spindle, Right 5X5 Camaro Cup 34610L4 Spindle, Left 5X5 Camaro Cup SC1449HW114 Sway bar 1-1/4” SC1449HW138 Sway bar 1-3/8” SC1449HW112 Sway bar 1-1/2” 23925 Bushing Delron for splined swaybar 23926 Swaybar arm Left 23927 Swaybar arm Right 23611 Rear Sway Bar Kit 31180 Panhard Axle Mount Rear Ford 9” 31990 Axle clamp, special for 3” tube 30786 Panhard Assembly 30780 Panhard Mount, Frame 3252 Axle Stops 32009 Winters 9” third link bracket 20613 Wheel Studs rear. PF059 Brake upgrade kit MK2 front, Parts below marked *

36571 Front Hubs, 5X4.75, Steel mk2 * 20536 Hub Dust Cover mk2 * 20573 Brake rotor hat * 36574 T-nuts for hat * 300-0802 Bolt for t-nut * 36573G Hans cooling gasket * SRS800 Brake blower fan new.

SRS801 Brake blower fan adapter new.

SRS400 Brake blower fan * Out of production.

SRS002 Fan blower replacement

14

SRS004 Engine fan blower replacement

RE309 Brake cooler nose air duct kit right *

RE309L Brake cooler nose air duct kit left *

RE309S Screen for brake duct *

RE2034 Brake air hose 4,5” Length 14” *

RE2031 Brake air hose 3” Length 12`(4m) *

B941L Brake fan mount Left Pro syst. *

B941 Brake fan mount Right Pro syst. *

205500 Front hubs 5x4,75” Steel Mk1 20538 Hub dust cover Mk1 205700 Rear Hubs 5x4,75 Steel 20547 Drive flange 9” 44122 Wheel spacer 9” TG3001-33 Axle gundrilled Left 33”


RV102 Rear end vent assy 9” KN62-1460 Filter for vent tank 32258 Axle tube seal

QDR1 Quafie ATB Diff. CCRMk1/Winters Rear axle 9” W95590 Winters 9” housing with axle tubes WA94303 Winters 9” center section HUR114-7494 Shift Boot Hurst PM8182 Alternator 75A KRC8172 Alternator 50A 90-293-1630 Alternator 40A RE200 Naca duct single hole KRC40140640 Alernator pulley LS3CC GDY4060720 Drive belt LS3CC GDY4060725 Drive belt to P/S pump T40S

E113 Alternator bracket LS3CC E7015 ECM mount LS3CC PF062 GM ECM LS3CC E7016 Engine wire harness LS3CC 9026, 9027 Engine Skid Pan R100 Engine spacer ¼” R1005 Engine spacer ½”

15

E15910 Engine vent tank for valve covers LS3CC E1597 Oil filter block off line adapter LS3CC 82892 Hydr. Bearing line and bleed kit incl. coupler QM188395 Drive Shaft, Aluminum 39.5" QM188545 Drive Shaft, Yoke 243950 Drive shaft steel


329-10 Drive Shafts U-Bolts 9” 369YOKE Machined Yoke 36299, 36299L Motor mounts front LS3CC 3611 Motor Mounts, Rear Left 3613 Motor Mounts Rear Right ATM2271 Water temp fitting at water pump 3/8” NPT LS3CC 58982 Rad. Hose reducer 1,75” to 1,5” LS3CC 58981 Rad. Hose reducer 1,5” to 1,25” LS3CC 342411 Vertical surge tank LS3CC 28474 ,75” Dia. 90° hose from surge tank to water pump LS3CC HRP90150 1,5” 90° blue hose LS3CC HRP45175 1,75” 45° blue hose LS3CC 34312 Rad. Hose connector 3,5” Long (1 of 1,5” dia.) LS3CC 34322 Rad. Hose connector 4” Long (1 of 1,75”) LS3CC 34129C10 Radiator, W/Oil Cooler 3427 Radiator Cap 3426 Spool Thermostat replacement 34221 Radiator Hoses, Overflow Tank & Lines 342026 Upper Radiator Mount, Left 342027 Upper Radiator Mount, Right M162K Fan, electric 16” pull MFA104 Fan, mounting kit CAN22625 Remote Oil Filter Mount E3005 Engine Oil Filter Line Kit LS3CC E1599 Dry sump oil tank LS3CC E164 Dry sump oil tank mounting brackets and straps LS3CC E165 Dry sump oil tank heat shield LS3CC 50-625-7612 Engine Oil cooler in Air box 7,5”x11” LS3CC 22-M22AN10-SE Setrab cooler fitting E166 Engine Oil cooler mount LS3CC

16

GS1003-12 Seals IT gasket 21044 SLP Air box LS3CC 25166571 Plastic GM filter mount LS3CC 25042562 Air filter GM/AC Delco E146 Alum. angle filter box mount LS3CC E7004 20° 3,5” elbow LS3CC E7003 3,5” to 4” Hose connector LS3CC E145 Air deflector LS3CC H11213C New headers LS3CC narrower chassi clearance LS3CC H2024C Y-pip LS3CC 3,5” to 3,5” LS3CC H2111C Exhaust tail pipe only, old version

B907 catalytic convertor heat shield H3032 Exhaust Hanger Centred Around catalytic Converter H3031 Muffler / Exhaust Hanger Rear H3028 Exhaust Hanger Rubber HPFC300 Stainless Exhaust band clamp 3” PF140 Brake upgrade kit 2018. Below parts marked #



CCA029660-355 AP Caliper bracket #




120-6387-RS Wilwood Caliper, 6 Piston, Front. Out of production. 120-6388-RS Wilwood Caliper, 6 Piston, Front. Out of production. 120-8283L Wilwood Caliper, 4 Piston, Rear 120-8283R Wilwood Caliper, 4 Piston, Rear 120-11127 Wilwood Caliper, 4 Piston Rear L&R #


340910 Cast clamp on bracket 9” B716SHCS Caliper bolts CP5772-1137RA Rotor, Directional Left. AP Front #

CP5772-1136RA Rotor, Directional Right. AP Front #

CP1901727 Rotor, Directional Left, AP Front and Rear. CP1901726 Rotor, Directional Right, AP Front and Rear. CP1901782 Rotor, Directional RH AP Rear

17

CP1901783 Rotor, Directional LH AP Rear B926 Brake Cooler plastic holder B931 Caliper cooler mount SRS400 Brake blower fan 3383219 Brake Line 21” w/90* fitting 338326 Brake Line 26” FBM2511 Brake Line Fitting 33791 Brake Line Fitting 80171 Painless Brake Light Switch RT-RD24 Tail Lights, 70 x 118 mm LED Aftermarket B925C Tail Lights bracket TLT74-875 Master Cylinder 7/8” TLT74-1000 Master Cylinder 1” TLT74-200 Fitting Plastic

TLT74-208 Master Cyl. Clamp

524312 Master Cylinder, Remote Reservoir 3/4” 524314 Master Cylinder, Remote Reservoir 7/8” 524316 Master Cylinder, Remote Reservoir 1” 524312K Master Cyl. O-ring repair ¾” 524314K Master Cyl. O-ring repair 7/8” 524316K Master Cyl. O-ring repair 1” AU12685 Master Cylinder Hose Clamp RD109 Master Cylinder Hose 5/16” 524353 Master Cylinder Fitting B9524 Master cyl. Reservoir heat shield CP0805420 Master Cylinder Reservoir, Double Port CP0805424 Master Cylinder Reservoir, Single Port CP2293-48 Bellows for Master Cylinder Reservoir 524361 Master Alum. Cyl. Reservoir Double port

524360 Master Alum. Cyl. Reservoir Single port



BR11078 1/8 npt to 3/16 inverted flare 90* WW260-1874 Residual Valve 2# 52692 Pedal, Brake Floor Mounted 52992 Pedal, Clutch Floor Mounted 52591 Clutch Pedal Stop 5299 Dead Pedal

18

WW340-4990 Brake Bias Adjuster 72560 90* Bias Adjuster TC1000LS1 Throttle Cable LS3CC 52502 Engine mount for throttle cable LS3CC 5237 Pedal, Gas 52351 Throttle Stop OP-11B Fuel Cell bracket 13202 Fuel Filler 13202B Fuel Filler bracket RF215 Fuel Line Kit LS3CC RUS644120 Fitting for fuel rail inlet LS3CC PC122F-EFI Fuel cell w/internal pump LS3CC PC122F-B Fuel Cell Bladder

HP2010 Fuel filter LS3CC HP1200 Fuel filter replacement LS3CC HP2010B Fuel filter mount LS3CC FSC1 Fuel Safe pump in tank kit LS3CC FPHP El. Fuel pump LS3CC 9120 battery heat shield E5495 Battery shut off switch 4 post

MOR74102 Battery shut off switch 4 post 300Amp

RRCWH Chassis Wiring Harness E4407T Guage Panel, W/Tach E3316 Fuel Level Guage KS210-10 Fuel Level Sender E3563 Fuel Pressure Gauge LS3CC B902CC Switch Panel W/Accessory B902LCC Switch Panel Cover B908 Dash panel cover plate B913 Dash panel cover plate spacer B914 Defogger Diffuser Box B9140 Defogger blower bracket RE195 Defogger Fan B930 Ignition mounting plate RF125A Heat Shield, Extreme Temperature RF126A Heat Shield, Standard Grade RF127A Roll Aluminum Sealant Tape

19

B915 Heat Shield Behind Driver Seat B80190 Windsheild tear off 65030 Roll Bar Padding BCS155601 Roll Bar Padding FIA Type A 465-1004 ¼” Cable clamps 465-1006 3/8” Cable clamps 465-1014 1” Cable clamps 22534 Rearview Mirror 4408 Body, Challenger 2014, Includes Front & Rear Windows. 40036 Left side opening door hardware B1017 Hood Pins, Pair, CHASCR Nose Screen, Challenger CHADLB Deck Lid Bracket and Hinge Assy, Challenger B932LD Cowl support Left Challenger B932RD Cowl support Right Challenger AS-105552 V-SPEC Wing AA-100038 Wing sideplate carbon B917D Splitter B9171 Splitter Pinch plate

B918 Splitter brace FS807-3 Splitter adj. braces PF050 Upper brake light LED CHAHLD Decal Challenger head light and front grill CHATLDR Decal Challenger rear light right CHATLDL Decal Challenger rear light left CAMIFL Extended Inner Fender behind front tire Left CAMIFR Extended Inner Fender behind front tire Right CHABB Front and Rear Roof Support Brackets 4001 Window Net 40020 Window Net mount lower

40025 Latch bar to net.

WM KIT AFI Wiper Kit AM2301353 Wiper motor to AFI

AM3022160 Wiper blade to AFI

FS805 Window Installation Kit B800D Window Braces B800DR Window Brace rear

20

B1017A Trunk Fasteners, Pair PF027 Tow Straps PF045 Tow decal B927 Jack post plate B928D Window brace bracket B929D Exhaust exit flange plate B9195D Side view mirror right B9205D Side view mirror left B919D Mirror bracket left side B920D Mirror bracket right side 90181 Ready made body mounts 90182 Ready made body mounts B940 Lowers on Hood. 4011D Hood, Challenger 4015D Trunk, Challenger 4040D Quarter Panel, Right, Challenger 4041D Quarter Panel, Left, Challenger 4042D Rear Cover, Right, Challenger 4043D Rear Cover, Left, Challenger 4044D Rear Center Diffuser, Challenger 4045DN Nose Left Challenger 4046DN Nose Right Challenger 4072D Fender, Right, Challenger 4073D Fender, Left, Challenger 4080D Door, Right, Challenger 4081D Door, Left, Challenger Lower 40815D Door, Left, Challenger Upper 40820D Roof, Rear Section, Challenger 4082D Roof, Front Section, Challenger B8019D Front Window, cut, drilled and Blackout. Challenger B923D Rear Window, cut, drilled and Blackout. Challenger B921D Quarter Window, R/S Challenger B922D Quarter Window, L/S Challenger B924 Quarter Panel Brace 493 Sliding rail 0146EM41A Fire extinghuiser L-102-400-001 Fire system Life Line


1

NEZ V8 Thunder Cars Bulletin 20180226-1 Eligible cars: During 2018 there is only two cars with old Chevrolet 350ci ZZ4 V8 engine that will be allowed to participate in NEZ V8 Thunder Cars racing series. From 2019 this engine will be prohibited. Those cars have following chassis number and starting number: Chassis number H3490 and starting number #22. Chassis number H3506 and starting number #50. These engines must follow old engine rules as follow: Bilaga 1.4 Motor GM ZZ4 GM part number: 24502609 Chevrolet engine ZZ4 10105123 Engineblock 12556307 Crankshaft. Castingnr:14088532 12556463 Head 12480002 Camshaft kit 24502586 Camshaft 12551483 Valve springs or Crane Cams valve springs part nr:99846-16. 10212808 Retainers or replacement nr: 19169661 12370839 Roller rockers 10185063 Intake manifold 5,1 Free components: Valves, but dimensions must be retain original 1,94” intake and 1,50” exhaust. Material must be steel. Valve locks, Valve sealings, Pushrods. Valve lifters, but must be hydraulic roller lifter. Valve guides free. Timing chain. Must be chain type. Camshaft cover. Flywheel with starter ring gear. Min.weight = 6800kilogram and made of steel. Main and Rod bearings.. Torsion damper.

2

Pistons, made by aluminum, cast or forged type. Piston top must be totally flat. Machining of valve pockets are allowed. Piston rings. Rod Bolt in Steel. Rods made in steel. Min.weight =590kilogram with bolt/nut washer included. Min.length = 5,700” Max length =6,100”. Screw, nuts, plugs, washers, freeze plugs. Oil pump, must be mechanical driven and mounted on original location. Oil pump shaft. Oil pick up. Oil pan. We recommend part nr: CP100LTRB-RR. Gaskets, but steel gasket between engine block and heads are NOT allowed. 5,2 Maching engine block. Max. Cyl. drill dia = 102,50mm. Max. stroke = 88,39mm. Min. distance between engine block/head surface and crankshaft center = 228,50mm. It is allowed to put in max. 4 sleeves to allow repair of engine block. Cyl.drilling, flatness grinding, block decking, line honing is allowed. 5,3 Heads Volume combustion chamber = min.55cc. Volume measures with valves and spark plug mounted, without head gasket. Flatness grinding of heads allowed, machining to allow valve guides allowed. Valve seat angles are free in steel seat. 5,4 Crank shaft Grinding of main and rod pin is allowed. Balance and surface hardening is allowed. Min. weight = 23 360kilogram. 5,5 Carburetor Holley 750cfm part nr: 4779 Choke valve and controls are allowed to remove. Free parts: Main nozzle, Acceleration nozzle, Acceleration pumps and floaters. Distance between carb and manifold is mandatory. Thickness Min. 25,00mm Max. 28,00mm including gaskets. Air filter free, but following dim. Must be kept 14” x 4”. Fuel E85 should be used.

3

5,6 Clutch Clutch is free, on ZZ4 engine, with following limitation: Max. 1pc. Clutch disc. Hydraulic release bearing free. 5,7 Ignition Distributor: MSD 85551 Ignition box: MSD 6AL 6420 or 6425 Ignition coil: MSD 8252 Spark plug wires free. Spark plugs free.

Date post:	15-Sep-2018
Category:	Documents
Upload:	ngokiet
View:	214 times
Download:	0 times

V8 Thunder Cars NEZ regulations... · V8 Thunder Cars NEZ North European Technical Regulations...

Documents