VA2C Vane Air Motor
3.386"
1.713"
2.047"
0.118"
6.496"
2.165"1.063"diameter
1.969"
4.016"
2.028"
2.065"
0.6250"0.6245"diameter
4.4988"4.4961" diameter
2 ports3/8" NPT
4 holes - 3/8" - 16-UNCEquispaced on 5.875" P.C.D.
Mountingspigot
Key 0.187" squarex 1.437" long
Port A
Max. Overhung Force on shaft 400 N (90 lbf.)Axial loads should be kept to a minimumMass 4.40 kg (9.70 lb.)
Attitude: The motor can be operated in all positionsMaximum temperature -20°C to +80°C (-4°F to +176°F)Muffler supplied with motor
Note: With air inlet at port 'A', shaftrotation is clockwise looking on shaft.For opposite rotation reverse ports.Motor is reversible
Nema 56C configuration
Motor code : VA2CXXX10
VA2J Vane Air Motor
2.835"
1.161"
1.752"
0.630"
1.000"
0.945"
0.591" 1.496"
4.016"
2.165"1.063"diameter
2.992"3.543"
2.028"
3.498"
0.5000"0.4995"diameter
2 ports3/8" NPT
4 mounting holes0.276" diameter
0.453" A.F.
Port A
Max. Overhung Force on shaft 400 N (90 lbf.)Axial loads should be kept to a minimumMass 3.30 kg (7.27 lb.)
Attitude: The motor can be operated in all positionsMaximum temperature -20°C to +80°C (-4°F to +176°F)Muffler supplied with motor
Note: With air inlet at port 'A', shaftrotation is clockwise looking on shaft.For opposite rotation reverse ports.Motor is reversible
Foot mounting configuration
Motor code : VA2JXXX10
VA2X Vane Air Motor
2.835"
1.161"
1.752"
0.630"
1.000"
4.016"
2.165"1.063"diameter
1.969"
0.156"
15°
2.028"
2.065"
0.5000"0.4995"diameter
1.7488"1.7472" diameter
2 ports3/8" NPT
3 holes - 1/4" - 20-UNCx 12mm (0.47") deepon 2.500" P.C.D.
Mountingspigot
0.453" A.F.
Port A
Max. Overhung Force on shaft 400 N (90 lbf.)Axial loads should be kept to a minimumMass 3.20 kg (7.05 lb.)
Attitude: The motor can be operated in all positionsMaximum temperature -20°C to +80°C (-4°F to +176°F)Muffler supplied with motor
Note: With air inlet at port 'A', shaftrotation is clockwise looking on shaft.For opposite rotation reverse ports.Motor is reversible
Face mounting configuration
Motor code : VA2XXXX10
VS2C Vane Air Motor
14 mm
26 mm
2 holes M6 x10 mm (0.40") deep
86 mm
43.5 mm
30 mm
3.5 mm
9 mm
36.0 mm
160 mm
55 mm27 mmdiameter
50 mm
96 mm
104.0 mm
52.45 mm
14.012 mm14.001 mmdiameter
16.000 mm15.870 mm over key
110.000 mm109.946 mm diameter
2 portsG 3/8"
Tapped hole in shaftM5 x 15 mm(0.59") deep
4 holes 9 mm diameterEquispaced on 130.00 mm P.C.D.
Mountingspigot
Key 5.00 mm square x 20.0 mm long rounded ends
Port A
Max. Overhung Force on shaft 400 N (90 lbf.)Axial loads should be kept to a minimumMass 4.40 kg (9.70 lb.)
Attitude: The motor can be operated in all positionsMaximum temperature -20°C to +80°C (-4°F to +176°F)Muffler supplied with motor
Note: With air inlet at port 'A', shaftrotation is clockwise looking on shaft.For opposite rotation reverse ports.Motor is reversible
D71 configuration
Motor code : VS2CXXX00
V2 Series Vane Air Motor
0 1000 2000 3000 4000
1
2
3
4
7 bar
6 bar
5 bar
4 bar
3 bar
2 bar
SPEED revs per min
TORQUENm
TORQUE - SPEED
0 1000 2000 3000 4000
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9 7 bar
6 bar
5 bar
4 bar
3 bar
SPEED revs per min
kWPOWER - SPEED
0 1 2 3 4 5 6 7
1
2
3
4
MinimumStartingTorque
MaximumStartingTorque
PRESSURE Bar
TORQUENm
TORQUE - PRESSURE
STARTING TORQUE will v ary between theminimum and maximum lev els shown.The actual starting torque will depend on theair inlet pressure and the motor crank position.
When designing f or applications where the minimum start torque requirement is equal tothe running torque (as f or example on hoists),the motor should be operated in the area belowthe min starting torque. This will ensure that themotor will alway s hav e adequate starting torque
0 1000 2000 3000 4000
4
8
12
16
20
24
28
32 7 bar
6 bar
5 bar
4 bar
3 bar
2 bar
SPEED revs per min
Free airl/sec
AIR CONSUMPTION - SPEED
Maximum continuous speed 4000 rpm
AIRLINE FILTRATION AND LUBRICATIONUse 64 micron filtration or better. Choose a lubricator suitable for the flow required. Prior to initial start-up,inject oil into the inlet port.Lubricator drop rate 4-5 drops/minute continuous operationLubricator drop rate 9-12 drops/minute intermittent operation
Max. Overhung Force on motor shaft 400 N (90 lbf.)Axial loads should be kept to a minimum
Attitude: The motor can be operated in all positionsMaximum temperature -20°C to +80°C (-4°F to +176°F)
Muffler supplied with motorMotor is reversible
A pressure regulator should be used to control the air pressure to the motor, to limit the maximumoutput torque applied to the driven assembly.
VA2C MotorSpare Parts List
Item Part No. Description Qty Kit No.
01 720-001 BSP Body 102 740-518 Front Plate NEMA 56C 103 740-002 End Plate 104 - Gasket 2 729-91005 720-910 Rotor Shaft Assy 106 720-006 Ejection Ring 207 - Blades 4 729-91008 740-008 Cover Plate 1
09-1 - Gasket 1 729-91009-2 - Gasket 1 729-91009-3 - Gasket 1 729-910
11 802-001 Screw 312 809-007 Cap Screw 1213 - Circlip 1 729-91014 806-024 Dowel 415 807-025 Bearing 116 807-028 Bearing 117 - Oil Seal 1 729-91018 - O Ring 1 729-91020 720-100 Seal Bearing Ring 122 811-020 Key 1
729-910 V2 Seal Kit820-023 Silencer 3/8 NPT 1
If unit is pre 1990 supply consult manufacturer to confirm design
VA2J / VA2X MotorSpare Parts List
Item Part No. Description Qty Kit No.
01 720-001 BSP Body 102 740-003 Front Plate 103 740-002 End Plate 104 - Gasket 2 729-910
04A-1 - Gasket 1 729-91004A-2 - Gasket 1 729-91004A-3 - Gasket 1 729-910
05 720-911 Rotor Shaft Assy 106 720-006 Ejection Ring 207 - Blades 4 729-91008 740-008 Cover Plate 109 720-023 Foot 110 802-011 Screw 212 809-007 Cap Screw 1213 - Circlip 1 729-91014 806-024 Dowel 415 807-027 Bearing 116 807-028 Bearing 117 - Oil Seal 1 729-91018 - O Ring 1 729-91020 806-032 Dowel 2
729-910 V2 Seal Kit820-023 Silencer 3/8 NPT 1
If unit is pre 1990 supply consult manufacturer to confirm design
VS2C MotorSpare Parts List
VS2C Vane Motor
Item Part No. Description Qty Kit No.
01 720-101 BSP Body 102 740-535 Front Plate D71 103 740-002 End Plate 104 - Gasket 2 729-91005 720-920 Rotor Shaft Assy 106 720-006 Ejection Ring 207 - Blades 4 729-91008 740-008 Cover Plate 1
09-1 - Gasket 1 729-91009-2 - Gasket 1 729-91009-3 - Gasket 1 729-910
11 802-001 Screw 312 809-007 Cap Screw 1213 - Circlip 1 729-91014 806-024 Dowel 415 807-025 Bearing 116 807-028 Bearing 117 - Oil Seal 1 729-91018 - O Ring 1 729-91020 720-100 Seal Bearing Ring 122 811-027 Key 1
729-910 V2 Seal Kit820-003 Silencer 3/8 BSP 1
If unit is pre 1990 supply consult manufacturer to confirm design