Vauxhall Astra Owner's Manual · This Owner's Manual depicts left-hand drive vehicles. Operation is...

Vauxhall AstraOwner's Manual

Introduction .................................... 2In brief ............................................ 6Keys, doors and windows ............ 19Seats, restraints ........................... 45Storage ........................................ 70Instruments and controls ............. 89Lighting ...................................... 132Climate control ........................... 143Driving and operating ................. 153Vehicle care ............................... 211Service and maintenance .......... 260Technical data ........................... 263Customer information ................ 280Index .......................................... 284

Contents

2 Introduction

Introduction

Introduction 3

Vehicle specific dataPlease enter your vehicle's data onthe previous page to keep it easilyaccessible. This information isavailable in the sections "Service andmaintenance" and "Technical data"as well as on the identification plate.

IntroductionYour vehicle is a designedcombination of advanced technology,safety, environmental friendlinessand economy.This Owner's Manual provides youwith all the necessary information toenable you to drive your vehiclesafely and efficiently.Make sure your passengers areaware of the possible risk of accidentand injury which may result fromimproper use of the vehicle.You must always comply with thespecific laws and regulations of thecountry that you are in. These lawsmay differ from the information in thisOwner's Manual.Disregarding the description given inthis manual may affect your warranty.

When this Owner's Manual refers to aworkshop visit, we recommend yourVauxhall Authorised Repairer.For gas vehicles, we recommend aVauxhall Authorised Repairerlicensed to service gas vehicles.All Vauxhall Authorised Repairersprovide first-class service atreasonable prices. Experiencedmechanics trained by Vauxhall workaccording to specific Vauxhallinstructions.The customer literature pack shouldalways be kept ready to hand in thevehicle.

Using this manual● This manual describes all options

and features available for thismodel. Certain descriptions,including those for display andmenu functions, may not apply toyour vehicle due to modelvariant, country specifications,special equipment oraccessories.

● The "In brief" section will give youan initial overview.

● The table of contents at thebeginning of this manual andwithin each section shows wherethe information is located.

● The index will enable you tosearch for specific information.

● This Owner's Manual depicts left-hand drive vehicles. Operation issimilar for right-hand drivevehicles.

● The Owner's Manual uses theengine identifier code. Thecorresponding sales designationand engineering code can befound in the section "Technicaldata".

● Directional data, e.g. left or right,or front or back, always relate tothe direction of travel.

● Displays may not support yourspecific language.

● Display messages and interiorlabelling are written in boldletters.

4 Introduction

Danger, Warnings andCautions

9 Danger

Text marked 9 Danger providesinformation on risk of fatal injury.Disregarding this information mayendanger life.

9 Warning

Text marked 9 Warning providesinformation on risk of accident orinjury. Disregarding thisinformation may lead to injury.

Caution

Text marked Caution providesinformation on possible damage tothe vehicle. Disregarding thisinformation may lead to vehicledamage.

SymbolsPage references are indicated with 3.3 means "see page".Page references and index entriesrefer to the indented headings givenin the section table of content.Chronological order to select menuentries in the vehicle personalisationis indicated with I.Thank you for choosing a Vauxhall.We wish you many hours ofpleasurable driving.Your Vauxhall Team

Introduction 5

6 In brief

In brief

Initial drive information

Vehicle unlocking

Press c to unlock the doors and loadcompartment. Open the doors bypulling the handles.

Tailgate

5-door Hatchback: to open thetailgate, push the touchpad switchbelow the brand emblem.Sports Tourer: to open the tailgate,push the touchpad switch under thetailgate moulding.Radio remote control 3 20.Central locking system 3 23.Electronic key system 3 21.Load compartment 3 29.

In brief 7

Seat adjustmentLongitudinal adjustment

Pull handle, slide seat, releasehandle. Try to move the seat back andforth to ensure that the seat is lockedin place.Seat position 3 46.Manual seat adjustment 3 47.Power seat adjustment 3 49.

Backrests inclination

Turn handwheel. Do not lean onbackrest when adjusting.Seat position 3 46.Manual seat adjustment 3 47.Power seat adjustment 3 49.

Seat height

Lever pumping motionup : seat higherdown : seat lower

Seat position 3 46.Manual seat adjustment 3 47.Power seat adjustment 3 49.

8 In brief

Seat inclination

Press switchtop : front end higherbottom : front end lower

Seat position 3 46.Manual seat adjustment 3 47.Power seat adjustment 3 49.

Head restraint adjustment

Press release button, adjust height,engage.Head restraints 3 45.

Seat belt

Pull out the seat belt and engage inbelt buckle. The seat belt must not betwisted and must fit close against thebody. The backrest must not be tiltedback too far (maximum approx. 25°).To release belt, press red button onbelt buckle.Seat position 3 46, Seat belts3 55, Airbag system 3 57.

In brief 9

Mirror adjustmentInterior mirror

To adjust the mirror, move the mirrorhousing in the desired direction.Manual anti-dazzle interior mirror3 39.Automatic anti-dazzle interior mirror3 40.

Exterior mirrors

Select the relevant exterior mirror byswitching the rocker control to leftmirror (L) or right mirror (R). Adjustrespective mirror by the four-waycontrol.Convex exterior mirrors 3 38,Electric adjustment 3 38, Foldingexterior mirrors 3 38.Heated exterior mirrors 3 39.

Steering wheel adjustment

Unlock the lever, adjust the steeringwheel, then engage the lever andensure it is fully locked.Do not adjust the steering wheelunless the vehicle is stationary andthe steering wheel lock has beenreleased.Airbag system 3 57, Ignitionpositions 3 154.

10 In brief

Instrument panel overview

In brief 11

1 Power windows ..................... 402 Exterior mirrors ..................... 383 Central locking system .......... 234 Side air vents ...................... 1515 Cruise control ..................... 178

Speed limiter ....................... 180Forward collision alert ......... 181

6 Turn and lane-changesignals, headlight flash,low/high beam, high beamassist ................................... 138

Exit lighting ......................... 141

Parking lights ...................... 139

Buttons for DriverInformation Centre .............. 113

7 Instruments ........................ 103

Driver Information Centre .... 1138 Buttons for Driver

Information Centre .............. 1139 Forward collision alert

indicator ............................. 18110 Windscreen wiper and

washer, rear wiper andwasher ................................. 91

11 Centre air vents .................. 15112 Info-Display ........................ 11813 Anti-theft alarm system

status LED ........................... 3514 Hazard warning flashers .... 13715 Glovebox .............................. 7016 CD player17 Controls for Info-Display

operation ............................. 11818 Climate control system ........ 14419 Fuse box ............................ 233

Power connector .................. 9720 Traction Control system ..... 175

Electronic Stability Control . 176Sport mode ........................ 177Parking assist/Advancedparking assist ..................... 186Lane keep assist ................ 201Eco button for stop-startsystem ................................. 159

21 Manual transmission .......... 169Automatic transmission ...... 165Manual transmissionautomated ........................... 169

22 Power outlet .......................... 9623 Parking brake ...................... 17324 Power button ....................... 15525 Ignition switch with

steering wheel lock ............ 15426 Steering wheel adjustment . . 9027 Horn ..................................... 9128 Bonnet release lever .......... 21329 Storage compartment ........... 7130 Light switch ........................ 132

Headlight rangeadjustment ......................... 133

Front/rear fog lights ............ 138

Instrument illumination ....... 140

12 In brief

Exterior lighting

AUTO : automatic light controlswitches automaticallybetween daytime runninglight and headlight

8 : sidelights9 : headlights

Automatic light control 3 133.

Fog lightsPress button in light switch:> : front fog lights

ø : rear fog light

Headlight flash, high beam andlow beam

headlight flash : pull leverhigh beam : push leverlow beam : push or pull lever

High beam 3 133.Headlight flash 3 133.LED headlights 3 134.High beam assist 3 134.

Turn and lane-change signals

lever up : right turn signallever down : left turn signal

Turn and lane-change signals3 138, Parking lights 3 139.

In brief 13

Hazard warning flashers

Operated by pressing ¨.Hazard warning flashers 3 137.

Horn

Press j.

Washer and wiper systemsWindscreen wiper

HI : fastLO : slowINT : interval wiping

orautomatic wiping with rainsensor

OFF : off

For single wipe when the wiper is off,press lever down to position 1x.Windscreen wiper 3 91.

14 In brief

Windscreen washer

Pull lever.Windscreen washer system 3 91,Washer fluid 3 216, Wiper bladereplacement 3 219.

Rear window wiper

Turn outer cap to activate the rearwindow wiper:ON : continuous operationINT : intermittent operationOFF : off

Rear window washer

Push lever.Washer fluid is sprayed on the rearwindow and the wiper wipes a fewtimes.Rear window wiper/washer 3 93.

In brief 15

Climate controlHeated rear window

The heating is operated by pressingÜ.Heated rear window 3 42.

Heated exterior mirrorsPressing Ü also activates the heatedexterior mirrors.Heated exterior mirrors 3 39.

Demisting and defrosting thewindows

● Press V: the air distribution isdirected towards the windscreen.

● Set fan speed to highest level.● Set temperature control to

warmest level.● Switch on heated rear window Ü.● Open side air vents as required

and direct them towards the doorwindows.

Heating and ventilation system3 143.Air conditioning system 3 144.

TransmissionManual transmission

Reverse: with the vehicle stationary,depress clutch pedal and press therelease button on the selector leverand engage the gear.Manual transmission 3 169.

16 In brief

Automatic transmission

P : park positionR : reverseN : neutral modeD : automatic modeM : manual mode< : upshift] : downshift

The selector lever can only be movedout of P when the ignition is on andthe brake pedal is applied. To engageP or R, press the release button.Automatic transmission 3 165.

Manual transmission automated

N : neutral positionD : automatic modeM : manual mode< : upshift] : downshiftR : reverse

Engage reverse only whenvehicle is stationary.

Manual transmission automated3 169.

Starting offCheck before starting off● Tyre pressure and condition

3 238, 3 276.● Engine oil level and fluid levels

3 214.● All windows, mirrors, exterior

lighting and number plates arefree from dirt, snow and ice andare operational.

● Proper position of mirrors, seats,and seat belts 3 38, 3 46,3 56.

● Brake function at low speed,particularly if the brakes are wet.

In brief 17

Starting the engine

● Ignition switch: turn key toposition 2.Power button: pressEngine Start/Stop for a fewseconds until green LEDilluminates.

● Move the steering wheel slightlyto release the steering wheellock.

● Manual transmission: operateclutch and brake pedal.Manual transmission automated:operate brake pedal.

Automatic transmission: operatebrake pedal and move selectorlever to P or N.

● Do not operate accelerator pedal.● Diesel engines: wait until control

indicator ! for preheatingextinguishes.

● Ignition switch: turn key toposition 3 and release.

Power button: pressEngine Start/Stop and release.

Starting the engine 3 157.

Stop-start system

If the vehicle is at a low speed or at astandstill and certain conditions arefulfilled, an Autostop is activated.An Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.A restart is indicated by the needle atthe idle speed position in thetachometer.Stop-start system 3 159.

18 In brief

Parking

9 Warning

● Do not park the vehicle on aneasily ignitable surface. Thehigh temperature of theexhaust system could ignite thesurface.

● Always apply the parkingbrake. Activate the manualparking brake without pressingthe release button. Apply asfirmly as possible on a downhillslope or uphill slope. Depressbrake pedal at the same time toreduce operating force.For vehicles with electricparking brake, pull switch m fora minimum of one second untilcontrol indicator m illuminatesconstantly and electric parkingbrake is applied 3 109.

● Switch off the engine.● If the vehicle is on a level

surface or uphill slope, engagefirst gear or set the selector

lever to position P beforeremoving the ignition key orswitching off ignition onvehicles with power button. Onan uphill slope, turn the frontwheels away from the kerb.If the vehicle is on a downhillslope, engage reverse gear orset the selector lever to positionP before removing the ignitionkey or switching off ignition onvehicles with power button.Turn the front wheels towardsthe kerb.

● Close the windows and thesunroof.

● Remove the ignition key fromthe ignition switch or switch offignition on vehicles with powerbutton. Turn the steering wheeluntil the steering wheel lock isfelt to engage.For vehicles with automatictransmission, the key can onlybe removed when the selectorlever is in position P.

For vehicles with manualtransmission automated, thekey can only be removed fromthe ignition switch when theparking brake is applied.

● Lock the vehicle with e on theradio remote control.Activate the anti-theft alarmsystem 3 35.

● The engine cooling fans may runafter the engine has beenswitched off 3 213.

Caution

After running at high enginespeeds or with high engine loads,operate the engine briefly at a lowload or run in neutral forapprox. 30 seconds beforeswitching off, in order to protectthe turbocharger.

Keys, locks 3 19, Laying-up thevehicle for a long period of time3 212.

Keys, doors and windows 19

Keys, doors andwindows

Keys, locks ................................... 19Keys .......................................... 19Radio remote control ................. 20Electronic key system ................ 21Memorised settings ................... 23Central locking system .............. 23Automatic locking ...................... 28Child locks ................................. 29

Doors ........................................... 29Load compartment .................... 29

Vehicle security ............................ 35Anti-theft locking system ........... 35Anti-theft alarm system .............. 35Immobiliser ................................ 37

Exterior mirrors ............................ 38Convex shape ........................... 38Electric adjustment .................... 38Folding mirrors .......................... 38Heated mirrors ........................... 39

Interior mirrors ............................. 39Manual anti-dazzle .................... 39Automatic anti-dazzle ................ 40

Windows ...................................... 40Windscreen ............................... 40Manual windows ........................ 40Power windows ......................... 40Heated rear window .................. 42Sun visors .................................. 42

Roof ............................................. 43Sunroof ...................................... 43

Keys, locksKeys

Caution

Do not attach heavy or bulky itemsto the ignition key.

Replacement keysThe key number is specified on adetachable tag.The key number must be quotedwhen ordering replacement keys as itis a component of the immobilisersystem.Locks 3 257, Central locking 3 23,Starting the engine 3 157.Radio remote control 3 20.Electronic key 3 21.The code number of the adapter forthe locking wheel nuts is specified ona card. It must be quoted whenordering a replacement adapter.Wheel changing 3 248.

20 Keys, doors and windows

Key with foldaway key section

Press button to extend. To fold thekey, first press the button.

Lock cylindersDesigned to free-wheel if they areforcefully rotated without the correctkey or if the correct key is not fullyinserted. To reset, turn cylinder withthe correct key until its slot is vertical,remove key then re-insert it. If thecylinder still free-wheels, turn the keythrough 180° and repeat operation.

Radio remote control

Enables operation of the followingfunctions via the use of the remotecontrol buttons:● central locking system 3 23● anti-theft locking system 3 35● anti-theft alarm system 3 35● power windows 3 40● sunroof 3 43

The remote control has a range of upto 100 metres, but may also be muchless due to external influences. Thehazard warning flashers confirmoperation.

Handle with care, protect frommoisture and high temperatures andavoid unnecessary operation.

Replacing battery in radio remotecontrolReplace the battery as soon as therange reduces.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.


1. Insert flat screwdriver into the slotand separate the back cover fromthe remote control by slightlyturning the screwdriver.

2. Remove and replace battery. UseCR 2032 or equivalent battery.Pay attention to the installationposition.

3. Insert the back cover in the areaof the key blade, fold down andclose.

Radio remote controlsynchronisationAfter replacing the battery, unlock thedoor with the key in the driver's doorlock. The radio remote control will besynchronised when you switch on theignition.

FaultIf the central locking system cannotbe operated with the radio remotecontrol, the cause may be one of thefollowing:● Fault in radio remote control.● The range is exceeded.● The battery voltage is too low.● Frequent, repeated operation of

the radio remote control while notin range, which will require re-synchronisation.

● Overload of the central lockingsystem by operating at frequentintervals, the power supply isinterrupted for a short time.

● Interference from higher-powerradio waves from other sources.

Manual unlocking 3 23.

Electronic key system

Enables a keyless operation of thefollowing functions:● central locking system 3 23● power tailgate 3 29● ignition switching on and starting

the engine 3 157The electronic key simply needs to beon the driver's person.Additionally, the electronic keyincludes the functionality of the radioremote control 3 20.Handle with care, protect frommoisture and high temperatures andavoid unnecessary operation.


NoticeDo not put the electronic key into theload compartment or in front of theInfo-Display.

Replacing battery in electronickeyReplace the battery as soon as thesystem no longer operates properlyor the range is reduced. The need forbattery replacement is indicated by amessage in the Driver InformationCentre 3 120.


To replace:

1. Press button at the back of theelectronic key unit and extract thekey blade from the housing.

2. Insert the key blade again forapprox. 6 mm and turn the key toopen the housing. Furtherinsertion of the key blade candamage the housing.

3. Remove and replace battery. UseCR 2032 or equivalent battery.Pay attention to the installationposition.

4. Close the housing and insert keyblade.


Electronic key synchronisationThe electronic key synchronises itselfautomatically during every startingprocedure.


FaultIf the central locking cannot beoperated or the engine cannot bestarted, the cause may be one of thefollowing:● Fault in electronic key.● Electronic key is out of reception

range.● The battery voltage is too low.● Overload of the central locking

system by operating at frequentintervals, the power supply isinterrupted for a short time.

● Interference from higher-powerradio waves from other sources.

To rectify the cause of the fault,change the position of the electronickey.Manual unlocking 3 23.

Memorised settingsWhenever the ignition is switched off,the following settings areautomatically memorised by theremote control unit or the electronickey:

● automatic climate control● lighting● Infotainment system● central locking system● Sport mode settings● comfort settings

The saved settings are automaticallyused the next time the ignition isswitched on with the memorised keyof the remote control unit 3 154 orelectronic key 3 21.A precondition is that Personalisationby Driver is activated in the personalsettings of the Info-Display. This mustbe set for each remote control unit orelectronic key which is used. Thestatus change is available only afterlocking and unlocking the vehicle.The assigned memory position of thepower seat is automatically recalledwhen switching on ignition and AutoMemory Recall is activated in theInfo-Display for the memorisedremote control or electronic key.Power seat 3 49.Vehicle personalisation 3 122.

Central locking systemUnlocks and locks doors, loadcompartment and fuel filler flap.A pull on an interior door handleunlocks the respective door. Pullingthe handle once more opens the door.NoticeIn the event of an accident in whichairbags or belt pretensioners aredeployed, the vehicle isautomatically unlocked.NoticeA short time after unlocking with theremote control the doors are lockedautomatically if no door has beenopened. A precondition is that thesetting is activated in the vehiclepersonalisation 3 122.


Remote control operation

Unlocking

Press c.Unlocking mode can be set in thevehicle personalisation menu in theInfo-Display. Two settings areselectable:● All doors, load compartment and

fuel filler flap will be unlocked bypressing c once.

● Only the driver's door, loadcompartment and fuel filler flapwill be unlocked by pressing conce. To unlock all doors, pressc twice.

Select the relevant setting in Settings,I Vehicle in the Info-Display.Info-Display 3 118.Vehicle personalisation 3 122.The setting can be saved for theremote control being used.Memorised settings 3 23.Unlocking and opening the tailgate3 29.

LockingClose doors, load compartment andfuel filler flap.

Press e.

If the driver's door is not closedproperly, the central locking systemwill not work.

ConfirmationOperation of the central lockingsystem is confirmed by the hazardwarning flashers. A precondition isthat the setting is activated in thevehicle personalisation 3 122.

Electronic key system operation

The electronic key must be outsidethe vehicle, within a range of approx.one metre of the relevant door side.


Unlocking

Press the button on the respectiveexterior door handle and pull thehandle.Unlocking mode can be set in thevehicle personalisation menu in theInfo-Display. Two settings areselectable:● All doors, load compartment and

fuel filler flap will be unlocked bypressing the button on anyexterior handle once.

● Only the driver's door, loadcompartment and fuel filler flapwill be unlocked by pressing the

button on the driver`s doorexterior handle once. To unlockall doors, press button twice.

The setting can be changed in themenu Settings in the Info-Display.Vehicle personalisation 3 122.

Locking

Press the button on any exterior doorhandle.All doors, load compartment and fuelfiller flap will be locked.

The system locks if any of thefollowing occurs:● It has been more than

five seconds since unlocking.● The button on an exterior handle

has been pressed twice withinfive seconds to unlock thevehicle.

● Any door has been opened andall doors are now closed.

If the driver's door is not closedproperly, the electronic key remains inthe vehicle or the ignition is not off,locking will not be permitted and awarning chime sounds three times.If there have been two or moreelectronic keys in the vehicle and theignition was on once, the doors will belocked even if just one electronic keyis taken out of the vehicle.

Unlocking and opening the tailgateThe tailgate can be unlocked andopened handsfree via moving the footbelow the rear bumper or by pushingthe touchpad switch under the brandemblem when the electronic key is inrange. The doors remain locked.Load compartment 3 29.


Operation with buttons on theelectronic key

The central locking system can alsobe operated with the buttons on theelectronic key.Press c to unlock.Press e to lock.Press X twice to unlock and openonly the power tailgate.Remote control operation 3 23.

Passive lockingAutomatic locking 3 28.

ConfirmationOperation of central locking system isconfirmed by the hazard warningflashers. A precondition is that thesetting is activated in the vehiclepersonalisation 3 122.

Central locking buttonsLocks or unlocks all doors, the loadcompartment and fuel filler flap fromthe passenger compartment via aswitch in the driver's door panel.

Press e to lock.Press c to unlock.

Operation with the key in case ofa central locking system faultIn case of a fault, e.g. vehicle batteryor remote control/electronic keybattery is discharged, the driver'sdoor can be locked or unlocked withthe mechanical key.The lock cylinder in the driver's dooris covered by a cap.

Remote control: to remove the cap,insert the key into the recess at thebottom of the cap and swivel the keyupward.Keys 3 19.


Electronic key: to remove the cap,press button at the back and extractthe key blade from the housing. Insertthe key into the recess at the bottomof the cap and swivel the key upward.Electronic key system 3 21.

Manual unlocking

Manually unlock the driver's door byinserting and turning the key in thelock cylinder.The other doors can be opened bypulling the interior handle twice or bypressing c in the driver's door panel.The load compartment and fuel fillerflap will possibly not be unlocked.By switching on the ignition, the anti-theft locking system is deactivated.

Manual locking

Push inside locking knob of all doorsexcept driver's door or press e in thedriver's door panel. Then close thedriver's door and lock it from theoutside by turning the key in the lockcylinder. The fuel filler flap andtailgate are possibly not locked.


After locking, cover the lock cylinderwith the cap: insert the cap with thelower side in the recesses, swivel andpush the cap until it engages at theupper side.

Automatic lockingAutomatic locking after driving offThis security feature can beconfigured to automatically lock alldoors, load compartment and fuelfiller flap after driving off andexceeding a certain speed.

When at a standstill after driving, thevehicle will be unlocked automaticallyas soon as the key is removed fromthe ignition switch, or with electronickey system when the ignition isswitched off.Activation or deactivation ofautomatic locking can be set in themenu Settings, I Vehicle in the Info-Display.Info-Display 3 118.Vehicle personalisation 3 122.The setting can be saved for theremote control or electronic key beingused 3 23.

Automatic relock after unlockingThis feature can be configured toautomatically lock all doors, loadcompartment and fuel filler flap ashort time after unlocking with theremote control or electronic key,provided no door has been opened.Activation or deactivation ofautomatic relock can be set in themenu Settings, I Vehicle in the Info-Display.Info-Display 3 118.

Vehicle personalisation 3 122.The setting can be saved for theremote control or electronic key beingused 3 23.

Passive lockingOn vehicles with electronic keysystem, this feature locks the vehicleautomatically after several seconds ifan electronic key has beenrecognised previously inside thevehicle, all doors have then beenclosed and the electronic key doesnot remain within the vehicle.If the electronic key remains in thevehicle or the ignition is not off,passive locking will not be permitted.If there have been two or moreelectronic keys in the vehicle and theignition was on once, the featurelocks the vehicle if just one electronickey is taken out of the vehicle.Passive locking can be disabled bypressing c for a few seconds whileone door is open. It remains disableduntil e is pressed or the ignition isswitched on.


Activation or deactivation of passivelocking can be set in the menuSettings, I Vehicle in the Info-Display.Info-Display 3 118.Vehicle personalisation 3 122.The setting can be saved for theelectronic key being used 3 23.

Child locks

9 Warning

Use the child locks wheneverchildren are occupying the rearseats.

Move the pin in the rear door to thefront. The door cannot be openedfrom the inside.To deactivate, move the pin to therear position.

DoorsLoad compartmentTailgate

Opening5-door Hatchback

After unlocking, push the touchpadswitch under the brand emblem andopen the tailgate.


Sports Tourer

After unlocking, push the touchpadswitch under the tailgate mouldingand open the tailgate manually.Central locking system 3 23.

Closing

Use one of the interior handles.Do not push the touchpad switchwhilst closing as this will unlock thetailgate again.Central locking system 3 23.

Power tailgate

9 Warning

Take care when operating thepower tailgate. Risk of injury,particularly to children.

Keep a close watch on themovable tailgate when operating.Ensure that nothing becomestrapped during operating and noone is standing within the movingarea.

The power tailgate can be operatedby:● Pressing X twice on the

electronic key.● Handsfree operation with motion

sensor below the rear bumper.● The touchpad switch under the

exterior tailgate moulding andC in the open tailgate.

● The switch C on the inside ofthe driver's door.

On vehicles with automatictransmission, the tailgate can only beoperated when the vehicle isstationary and automatictransmission in P.The turn signal lights flash and achime sounds when the powertailgate is operating.


NoticeOperating the power tailgate doesnot operate the central lockingsystem. To open the tailgate with thebutton on the electronic key, or withthe touchpad switch under thetailgate moulding or via handsfreeoperation, it is not necessary tounlock the vehicle. A precondition isthat the electronic key is outside thevehicle, within a range of approx.one metre of the tailgate.Do not leave the electronic key in theload compartment.Lock the vehicle after closing if it wasunlocked previously.

Central locking system 3 23.

Operation with the electronic key

Press X twice to open or close thetailgate.

Handsfree operation with motionsensor below the rear bumper

To open or close the tailgate move thefoot below the rear bumper back andforth in the area shown in theillustration. If equipped with parkingassist, the area is recognisable belowthe shown sensor. Do not hold thefoot longer or move too slow belowthe bumper. The electronic key mustbe outside the vehicle, within a rangeof approx. one metre of the tailgate.


9 Danger

Do not touch any vehicle partsbelow the vehicle duringhandsfree operation. There is arisk of injury from hot engine parts.

Operation with the touchpad switchunder the exterior tailgate moulding

To open the tailgate, press thetouchpad switch under the tailgatemoulding until the tailgate starts tomove. If the vehicle is locked, theelectronic key must be outside thevehicle, within a range of approx.one metre of the tailgate.

To close, press C in the opentailgate until the tailgate starts tomove.

Operation with the switch on theinside of the driver's door

Press C on the inside of the driver'sdoor until the tailgate starts to open orclose.

Stop or change direction ofmovementStop movement of the tailgateimmediately:● press X once on the electronic

key, or● press the touchpad switch under

the exterior tailgate moulding, or


● press C on the open tailgate,or

● press C on the inside of thedriver's door.

Pressing one of the switches againwill reverse the direction ofmovement.

Operation modesThe power tailgate has three modesof operation, which are controlled bythe switch C in the driver's door. Tochange the mode, turn the switch:

● Normal mode MAX: Powertailgate opens to full height.

● Intermediate mode 3/4: Powertailgate opens to a reducedheight that can be adjusted.

● Mode Off: Tailgate can only beoperated manually.

Adjust reduced opening height inintermediate mode1. Turn operation mode switch to

3/4.2. Open power tailgate with any

operation switch.3. Stop movement at the desired

height by pressing any operationswitch. If required, manually movethe stopped tailgate to the desiredposition.

4. Press and hold the button C onthe inside of the open tailgate forthree seconds.

NoticeAdjusting opening height should beprogrammed at ground level.

A chime sound indicates the newsetting and the turn signal lights willflash. The reduced height can only setat an opening angle of above 30°.When turning the adjuster wheel inthe driver's door to intermediate mode3/4, the power tailgate will stopopening at the newly set position.


The tailgate can only be held open ifa minimum height is exceeded(minimum opening angle from 30°).The opening height cannot beprogrammed below that height.

Safety functionIf the power tailgate encounters anobstacle during opening or closing,the direction of movement willautomatically be reversed slightly.Multiple obstacles in one power cyclewill deactivate the function. In thiscase, close or open the tailgatemanually.The power tailgate has pinch sensorson the side edges. If the sensorsdetect obstacles between tailgate andchassis, the tailgate will open, until itis activated again or closed manually.The safety function is indicated by awarning chime.Remove all obstacles beforeresuming normal power operation.If the vehicle is equipped with factory-fitted towing equipment and a traileris electrically connected, the powertailgate can only be opened with the

touchpad switch or closed with G inthe open tailgate. Ensure that thereare no obstacles in the moving area.

OverloadIf the power tailgate is repeatedlyoperated at short intervals, thefunction is disabled for some time.Move tailgate manually into endposition to reset the system.

General hints for operatingtailgate

9 Danger

Do not drive with the tailgate openor ajar, e.g. when transportingbulky objects, since toxic exhaustgases, which cannot be seen orsmelled, could enter the vehicle.This can cause unconsciousnessand even death.

Caution

Before opening the tailgate, checkoverhead obstructions, e.g. agarage door, to avoid damage to

the tailgate. Always check themoving area above and behind thetailgate.

NoticeThe installation of certain heavyaccessories onto the tailgate mayaffect its ability to remain open.NoticeThe operation of the power tailgateis disabled under low vehicle batteryconditions. In this case, the tailgatemay not even by manually operable.NoticeWith the power tailgate disabled andall doors unlocked, the tailgate canonly be operated manually. In thisevent, manually closing the tailgaterequires significantly greater force.NoticeAt low outside temperatures thetailgate may not open fully by itself.In this case lift the tailgate manuallyto its normal end position.


Vehicle securityAnti-theft locking system

9 Warning

Do not use the system if there arepeople in the vehicle! The doorscannot be unlocked from theinside.

The system deadlocks all the doors.All doors must be closed otherwisethe system cannot be activated.If the ignition was on, the driver's doormust be opened and closed once sothat the vehicle can be secured.Unlocking the vehicle disables themechanical anti-theft locking system.This is not possible with the centrallocking button.

Activating

Press e on the radio remote controltwice within five seconds.

Anti-theft alarm systemThe anti-theft alarm system iscombined with the central lockingsystem.It monitors:● doors, tailgate, bonnet● passenger compartment

including adjoining loadcompartment

● vehicle inclination, e.g. if it israised

● ignition

ActivationAll doors must be closed and theelectronic key of the electronic keysystem must not remain in thevehicle. Otherwise the system cannotbe activated.● Radio remote control: self-

activated 30 seconds afterlocking the vehicle by pressing eonce.

● Electronic key system: self-activated 30 seconds afterlocking the vehicle by pressingthe button on any exterior doorhandle.


● Radio remote control orelectronic key: directly bypressing e twice withinfive seconds.

● Electronic key system withpassive locking enabled: brieflyactivated after passive lockingoccurs.

NoticeChanges to the vehicle interior suchas the use of seat covers, and openwindows or sunroof, could impair thefunction of passenger compartmentmonitoring.

Activation without monitoring ofpassenger compartment andvehicle inclination

Switch off the monitoring ofpassenger compartment and vehicleinclination when animals are beingleft in the vehicle, because of highvolume ultrasonic signals ormovements triggering the alarm. Alsoswitch off when the vehicle is on aferry or train.1. Close tailgate, bonnet, windows

and sunroof.2. Press o. LED in the button o

illuminates for a maximum often minutes.

3. Close doors.4. Activate the anti-theft alarm

system.Status message is displayed in theDriver Information Centre.

Status LED

Status LED is integrated in the sensoron top of the instrument panel.Status during the first 30 seconds ofanti-theft alarm system activation:LED illuminates : test, arming delayLED flashesquickly

: doors, tailgate orbonnet notcompletely closed,or system fault


Status after system is armed:LED flashesslowly

: system is armed

Seek the assistance of a workshop inthe event of faults.

DeactivationRadio remote control: Unlocking thevehicle by pressing c deactivates theanti-theft alarm system.

Electronic key system: Unlocking thevehicle by pressing the button on anyexterior door handle deactivates theanti-theft alarm system.

The electronic key must be outsidethe vehicle, within a range of approx.one metre of the relevant door side.The system is not deactivated byunlocking the driver's door with thekey or with the central locking buttonin the passenger compartment.

AlarmWhen triggered, the alarm hornsounds and the hazard warning lightsflash simultaneously. The numberand duration of alarm signals arestipulated by legislation.The anti-theft alarm system can bedeactivated by pressing c, bypressing the switch on the doorhandle with electronic key system orswitching on the ignition.A triggered alarm, which has not beeninterrupted by the driver, will beindicated by the hazard warninglights. They will flash quickly threetimes the next time the vehicle isunlocked with the radio remotecontrol. Additionally a warningmessage is displayed in the DriverInformation Centre after switching onthe ignition.

Vehicle messages 3 120.If the vehicle's battery is to bedisconnected (e.g. for maintenancework), the alarm siren must bedeactivated as follows: switch theignition on then off, then disconnectthe vehicle's battery within15 seconds.

ImmobiliserThe system is part of the ignitionswitch and checks whether thevehicle is allowed to be started withthe key being used.The immobiliser is activatedautomatically after the key has beenremoved from the ignition switch.If the control indicator d flashes whenthe ignition is on, there is a fault in thesystem; the engine cannot be started.Switch off the ignition and repeat thestart attempt.If the control indicator d continuesflashing, attempt to start the engineusing the spare key and seek theassistance of a workshop.


NoticeRadio Frequency Identification(RFID) tags may cause interferencewith the key. Do not have it placednear the key when starting thevehicle.NoticeThe immobiliser does not lock thedoors. You should always lock thevehicle after leaving it and switch onthe anti-theft alarm system 3 23,3 35.

Control indicator d 3 112.

Exterior mirrorsConvex shapeThe convex exterior mirror on thedriver's side contains an asphericalarea and reduces blind spots. Theshape of the mirror makes objectsappear smaller, which will affect theability to estimate distances.Side blind spot alert 3 194.

Electric adjustment

Select the relevant exterior mirror byswitching the control to left (L) or right(R). Then swivel the control to adjustthe mirror.In position o no mirror is selected.

Folding mirrors

For pedestrian safety, the exteriormirrors will swing out of their normalmounting position if they are struckwith sufficient force. Reposition themirror by applying slight pressure tothe mirror housing.


Electric folding

Switch control to o, then push thecontrol c down. Both exterior mirrorswill fold.Push the control down again - bothexterior mirrors return to their originalposition.If an electrically folded mirror ismanually extended, pressing downthe control will only electrically extendthe other mirror.

Heated mirrors

Operated by pressing Ü.Heating works with the enginerunning and is switched offautomatically after a short time.

Interior mirrorsManual anti-dazzle

To reduce dazzle, adjust the lever onthe underside of the mirror housing.


Automatic anti-dazzle

Dazzle from following vehicles atnight is automatically reduced.

WindowsWindscreenWindscreen stickersDo not attach stickers such as tollroad stickers or similar on thewindscreen in the area of the interiormirror. Otherwise the detection zoneof the sensor and the view area of thecamera in the mirror housing could berestricted.

Windscreen replacement

Caution

If the vehicle has a front-lookingcamera sensor for the driverassistance systems, it is veryimportant that any windscreenreplacement is performedaccurately according to Vauxhallspecifications. Otherwise, thesesystems may not work properlyand there is a risk of unexpectedbehaviour and/or messages fromthese systems.

Manual windowsThe door windows can be opened orclosed with the window cranks.

Power windows

9 Warning

Take care when operating thepower windows. Risk of injury,particularly to children.If there are children on the rearseats, switch on the child safetysystem for the power windows.Keep a close watch on thewindows when closing them.Ensure that nothing becomestrapped in them as they move.

Switch on ignition to operate powerwindows. Retained power off 3 156.


Operate the switch for the respectivewindow by pushing to open or pullingto close.Pushing or pulling gently to the firstdetent: window moves up or down aslong as the switch is operated.Pushing or pulling firmly to the seconddetent then releasing: window movesup or down automatically with safetyfunction enabled. To stop movement,operate the switch once more in thesame direction.

Safety functionIf the window glass encountersresistance above the middle of thewindow during automatic closing, it isimmediately stopped and openedagain.

Override safety functionIn the event of closing difficulties dueto frost or the like, switch on theignition, then pull the switch to the firstdetent and hold. The window movesup without safety function enabled.To stop movement, release theswitch.

Child safety system for rearwindows

Press z to deactivate rear doorpower windows; the LED illuminates.To activate, press z again.

Operating windows from outsideThe windows can be operatedremotely from outside the vehicle.


Press and hold c to open windows.Press and hold e to close windows.Release button to stop windowmovement.If the windows are fully opened orclosed, the hazard warning lights willflash twice.

OverloadIf the windows are repeatedlyoperated within short intervals, thewindow operation is disabled forsome time.

Initialising the power windowsIf the windows cannot be closedautomatically (e.g. afterdisconnecting the vehicle battery), awarning message is displayed in theDriver Information Centre.Vehicle messages 3 120.Activate the window electronics asfollows:1. Close doors.2. Switch on ignition.3. Pull switch until the window is

closed and keep pulling foradditional two seconds.

4. Push switch until the window iscompletely open and keeppushing for additionaltwo seconds.

5. Repeat for each window.

Heated rear window

Operated by pressing Ü.Heating works with the enginerunning and is switched offautomatically after a short time.

Sun visorsThe sun visors can be folded down orswivelled to the side to preventdazzling.If the sun visors have integral mirrors,the mirror covers should be closedwhen driving.A ticket holder is located on thebackside of the sun visor.


RoofSunroof

9 Warning

Take care when operating thesunroof. Risk of injury, particularlyto children.Keep a close watch on themovable parts when operatingthem. Ensure that nothingbecomes trapped in them as theymove.

Switch on ignition to operate thesunroof.

Open or closePress p or r gently to the firstdetent: sunroof is opened or closedas long as the switch is operated.Press p or r firmly to the seconddetent then release: the sunroof isopened or closed automatically.During closing the safety function isenabled. To stop movement, operatethe switch once more.

Raise or closePress q or r: sunroof is raised orclosed automatically. During closingthe safety function is enabled.

SunblindThe sunblind is manually operated.Close or open the sunblind by sliding.When the sunroof is open, thesunblind is always open.

General hints

Safety functionIf the sunroof encounters resistanceduring automatic closing, it isimmediately stopped and openedagain.

Override safety functionIn the event of closing difficulties, e.g.due to frost, hold the switch rpressed to the second detent. Thesunroof closes with safety functiondisabled. To stop movement, releasethe switch.

Closing sunroof from outsideThe sunroof can be closed remotelyfrom outside the vehicle.


Press and hold e to close the sunroof.Release the button to stop themovement.

Initialising after a power failureAfter a power failure, it may only bepossible to operate the sunroof to alimited extent. Have the systeminitialised by your workshop.

Seats, restraints 45

Seats, restraints

Head restraints ............................ 45Front seats ................................... 46

Seat position .............................. 46Manual seat adjustment ............ 47Power seat adjustment .............. 49Armrest ...................................... 52Heating ...................................... 53Ventilating .................................. 53Massage .................................... 54

Rear seats ................................... 54Armrest ...................................... 54Heating ...................................... 54

Seat belts ..................................... 55Three-point seat belt ................. 56

Airbag system .............................. 57Front airbag system ................... 60Side airbag system .................... 60Curtain airbag system ............... 61Airbag deactivation .................... 62

Child restraints ............................. 63Child restraint systems .............. 63Child restraint installationlocations ................................... 66

Head restraints

Position

9 Warning

Only drive with the head restraintset to the proper position.

The upper edge of the head restraintshould be at upper head level. If thisis not possible for extremely tallpeople, set to highest position, andset to lowest position for small people.

Adjustment

Head restraints on front seats

Height adjustmentPress release button, adjust height,engage.

46 Seats, restraints

Head restraints on rear seats

Height adjustmentPull the head restraint upwards orpress the catch to release and pushthe head restraint downwards.

Removal of rear head restraintsE.g. for load compartment extension3 72.

Press both catches, pull the headrestraint upwards and remove.

Front seatsSeat position

9 Warning

Only drive with the seat correctlyadjusted.

9 Danger

Do not sit nearer than 25 cm fromthe steering wheel, to permit safeairbag deployment.

9 Warning

Never adjust seats while driving asthey could move uncontrollably.

9 Warning

Never store any objects under theseats.


● Sit with buttocks as far backagainst the backrest as possible.Adjust the distance between theseat and the pedals so that legsare slightly angled when fullypressing the pedals. Slide thefront passenger seat as far backas possible.

● Set seat height high enough tohave a clear field of vision on allsides and of all displayinstruments. There should be atleast one hand of clearancebetween head and the roofframe. Your thighs should restlightly on the seat withoutpressing into it.

● Sit with shoulders as far backagainst the backrest as possible.Set the backrest rake so that it ispossible to easily reach thesteering wheel with arms slightlybent. Maintain contact betweenshoulders and the backrest whenturning the steering wheel. Donot angle the backrest too farback. We recommend amaximum rake of approx. 25°.

● Adjust seat and steering wheel ina way that the wrist rests on topof the steering wheel while thearm is fully extended andshoulders on the backrest.

● Adjust the steering wheel 3 90.● Adjust the head restraint 3 45.● Adjust the thigh support so that

there is a space approx. twofingers wide between the edge ofthe seat and the hollow of theknee.

● Adjust the lumbar support so thatit supports the natural shape ofthe spine.

Manual seat adjustmentDrive only with engaged seats andbackrests.

Longitudinal adjustment

Pull handle, slide seat, releasehandle. Try to move the seat back andforth to ensure that the seat is lockedin place.


Backrest inclination

Turn handwheel. Do not lean onbackrest when adjusting.

Seat height

Lever pumping motionup : seat higherdown : seat lower

Seat inclination

Press switchtop : front end higherbottom : front end lower


Lumbar support

Adjust lumbar support using the four-way switch to suit personalrequirements.Moving support up and down: pushswitch up or down.Increasing and decreasing support:push switch forwards or backwards.

Adjustable thigh support

Pull the lever and slide the thighsupport.

Power seat adjustment

9 Warning

Care must be taken whenoperating the power seats. Thereis a risk of injury, particularly forchildren. Objects could becometrapped.

Keep a close watch on the seatswhen adjusting them. Vehiclepassengers should be informedaccordingly.

Longitudinal adjustment

Move switch forwards/backwards.


Seat height

Move switch upwards/downwards.

Seat inclination

Tilt front of switch upwards/downwards.

Backrest inclination

Tilt switch forwards/backwards.

Lumbar support

Adjust lumbar support using thefour-way switch to suit personalrequirements.Moving support up and down: pushswitch up or down.Increasing and decreasing support:push switch forwards or backwards.


Adjustable thigh support

Pull the lever and slide the thighsupport.

Side bolster

Adjust seat backrest width to suitpersonal requirements.Press e to reduce backrest width.Press d to increase backrest width.

Memory function for power seatadjustmentTwo different driver's seat settingscan be stored.Memorised settings 3 23, Vehiclepersonalisation 3 122.

Storing memory position● Adjust driver's seat to desired

position.● Press and hold MEM and 1 or 2

simultaneously until a chimesounds.

Recall of memory positionsPress and hold 1 or 2 until the storedseat position has been reached.Releasing the button during seatmovement cancels the recall.

Automatic recall of memory positionsMemory positions are each assignedto the respective radio remote controlunit or electronic key.


The stored positions areautomatically recalled when theignition is switched on.To stop recall movement, press oneof the memory or power seat controls.Precondition is that Personalisationby Driver and Auto Memory Recall isactivated in the personal settings ofthe Info-Display.This function can be activated ordeactivated in the vehiclepersonalisation.Select the relevant setting in theVehicle menu in the Info-Display.Info-Display 3 118.Vehicle personalisation 3 122.

Easy exit functionFor a convenient exit out of thevehicle, the power driver seat movesrearwards when vehicle is stationary.To activate the easy exit function:● set selector lever to position P

(automatic transmission)● apply parking brake (manual

transmission)● switch off ignition

● remove key from the ignitionswitch

● open the driver's doorIf the door is already open, switch offignition to activate easy exit.To stop movement, press one of thememory or power seat controls.This function can be activated ordeactivated in the vehiclepersonalisation.Select the relevant setting in theVehicle menu in the Info-Display.Info-Display 3 118.Vehicle personalisation 3 122.

Safety functionIf the driver's seat encountersresistance during movement, therecall may stop. After removing theobstruction, press and hold theappropriate memory position buttonfor two seconds. Try recalling thememory position again. If the recalldoes not operate, consult aworkshop.

OverloadIf the seat setting is electricallyoverloaded, the power supply isautomatically cut-off for a short time.NoticeAfter an accident in which airbagshave been deployed, the memoryfunction for each position button willbe deactivated.

Armrest

The armrest can be slid forwards by10 cm. Under the armrest there is astorage compartment.Armrest storage 3 71.


Heating

Adjust heating to the desired settingby pressing ß for the respective seatone or more times. The controlindicator in the button indicates thesetting.Prolonged use of the highest settingfor people with sensitive skin is notrecommended.The seat heating will be reducedautomatically from highest level tomedium level after 30 minutes.Seat heating is operational whenengine is running and during anAutostop.

Stop-start system 3 159.

Automatic seat heatingDepending on the equipment, theautomatic seat heating can beenabled in the vehicle personalisationmenu in the Info-Display.Vehicle personalisation 3 122.When enabled, the heating of theseats will be activated automaticallyat vehicle start. The activation isbased on several parameters such asvehicle interior temperature, intensityand direction of the sun andtemperature setting of the electronicclimate control system for the driverand passenger side.As the vehicle's interior warms up, theseat heating level will be reducedautomatically until it finally goes off.The seat heating level being providedduring the automatic operation isshown by heated seat indicator lights.If the passenger seat is unoccupied,the automatic seat heating feature willnot activate the seat heating for thatseat.

The seat heating buttons can bepressed at any time to exit theautomatic seat heating for therespective seat and control the seatheating manually instead.

Ventilating

Adjust ventilating to the desiredsetting by pressing A for therespective seat one or more times.The control indicator in the buttonindicates the setting.Ventilated seats are operational whenengine is running and during anAutostop.Stop-start system 3 159.


Massage

Press c to switch on the backmassage function.To switch off, press c again.After ten minutes the massagefunction is switched off automatically.

Rear seatsArmrest

Fold armrest down.

Heating

Activate seat heating by pressing ßfor the respective rear outer seat.Activation is indicated by the LED inthe button.Press ß once more to deactivate seatheating.Prolonged use for people withsensitive skin is not recommended.Seat heating is operational whenengine is running and during anAutostop.Stop-start system 3 159.


Seat belts

The seat belts are locked duringheavy acceleration or deceleration ofthe vehicle holding the occupants inthe sitting position. Thereby the risk ofinjury is considerably reduced.

9 Warning

Fasten seat belt before each trip.In the event of an accident, peoplenot wearing seat belts endangertheir fellow occupants andthemselves.

Seat belts are designed to be used byonly one person at a time. Childrestraint system 3 63.Periodically check all parts of the beltsystem for damage, pollution andproper functionality.Have damaged componentsreplaced. After an accident, have thebelts and triggered belt pretensionersreplaced by a workshop.NoticeMake sure that the belts are notdamaged by shoes or sharp-edgedobjects or are trapped. Prevent dirtfrom getting into the belt retractors.

Seat belt reminderEach seat is equipped with a seat beltreminder, indicated for front seats bycontrol indicators X and k, or for rearseats by the symbol X in the DriverInformation Centre 3 107.

Belt force limitersStress on the body is reduced by thegradual release of the belt during acollision.

Belt pretensionersIn the event of a head-on, rear-end orside-on collision of a certain severity,the front and rear seat belts aretightened. The front seat belts aretightened by two pretensioners perseat. The outer rear seat belts aretightened by one pretensioner perseat.

9 Warning

Incorrect handling (e.g. removal orfitting of belts) can trigger the beltpretensioners.

Deployment of the belt pretensionersis indicated by continuous illuminationof control indicator v 3 108.Triggered belt pretensioners must bereplaced by a workshop. Beltpretensioners can only be triggeredonce.NoticeDo not affix or install accessories orother objects that may interfere withthe operation of the beltpretensioners. Do not make any


modifications to belt pretensionercomponents as this will invalidatethe vehicle type approval.

Three-point seat beltFasten

Withdraw the belt from the retractor,guide it untwisted across the bodyand insert the latch plate into thebuckle. Tighten the lap belt regularlywhilst driving by pulling the shoulderbelt.

Loose or bulky clothing prevents thebelt from fitting snugly. Do not placeobjects such as handbags or mobilephones between the belt and yourbody.

9 Warning

The belt must not rest against hardor fragile objects in the pockets ofyour clothing.

Seat belt reminder X, k 3 107.

Unfasten

To release belt, press red button onbelt buckle.


Using the seat belt while pregnant

9 Warning

The lap belt must be positioned aslow as possible across the pelvisto prevent pressure on theabdomen.

Airbag systemThe airbag system consists of anumber of individual systemsdepending on the scope ofequipment.When triggered, the airbags inflatewithin milliseconds. They also deflateso quickly that it is often unnoticeableduring the collision.

9 Warning

If handled improperly, the airbagsystems can be triggered in anexplosive manner.

NoticeThe airbag systems and beltpretensioner control electronics arelocated in the centre console area.Do not put any magnetic objects inthis area.Do not stick anything on the airbagcovers and do not cover them withother materials.Each airbag is triggered only once.Have deployed airbags replaced bya workshop. Furthermore, it might be

necessary to have the steeringwheel, the instrument panel, parts ofthe panelling, the door seals,handles and the seats replaced.Do not make any modifications tothe airbag system as this willinvalidate the vehicle type approval.

When the airbags inflate, escapinghot gases may cause burns.Control indicator v for airbag systems3 108.

Child restraint systems on frontpassenger seat with airbagsystemsWarning according to ECE R94.02:


EN: NEVER use a rearward-facingchild restraint on a seat protected byan ACTIVE AIRBAG in front of it;DEATH or SERIOUS INJURY to theCHILD can occur.DE: Nach hinten gerichteteKindersitze NIEMALS auf einem Sitzverwenden, der durch einen davorbefindlichen AKTIVEN AIRBAGgeschützt ist, da dies den TOD oderSCHWERE VERLETZUNGEN DESKINDES zur Folge haben kann.FR: NE JAMAIS utiliser un sièged'enfant orienté vers l'arrière sur unsiège protégé par un COUSSINGONFLABLE ACTIF placé devant lui,sous peine d'infliger desBLESSURES GRAVES, voireMORTELLES à l'ENFANT.ES: NUNCA utilice un sistema deretención infantil orientado haciaatrás en un asiento protegido por unAIRBAG FRONTAL ACTIVO. Peligrode MUERTE o LESIONES GRAVESpara el NIÑO.RU: ЗАПРЕЩАЕТСЯустанавливать детскоеудерживающее устройство лицомназад на сиденье автомобиля,

оборудованном фронтальнойподушкой безопасности, еслиПОДУШКА НЕ ОТКЛЮЧЕНА! Этоможет привести к СМЕРТИ илиСЕРЬЕЗНЫМ ТРАВМАМРЕБЕНКА.NL: Gebruik NOOIT een achterwaartsgericht kinderzitje op een stoel meteen ACTIEVE AIRBAG ervoor, omDODELIJK of ERNSTIG LETSEL vanhet KIND te voorkomen.DA: Brug ALDRIG en bagudvendtautostol på et forsæde med AKTIVAIRBAG, BARNET kan komme iLIVSFARE eller komme ALVORLIGTTIL SKADE.SV: Använd ALDRIG en bakåtvändbarnstol på ett säte som skyddas meden framförvarande AKTIV AIRBAG.DÖDSFALL eller ALLVARLIGASKADOR kan drabba BARNET.FI: ÄLÄ KOSKAAN sijoita taaksepäinsuunnattua lasten turvaistuintaistuimelle, jonka edessä onAKTIIVINEN TURVATYYNY, LAPSIVOI KUOLLA tai VAMMAUTUAVAKAVASTI.

NO: Bakovervendtbarnesikringsutstyr må ALDRI brukespå et sete med AKTIVKOLLISJONSPUTE foran, da det kanføre til at BARNET utsettes forLIVSFARE og fare for ALVORLIGESKADER.PT: NUNCA use um sistema deretenção para crianças voltado paratrás num banco protegido com umAIRBAG ACTIVO na frente domesmo, poderá ocorrer a PERDA DEVIDA ou FERIMENTOS GRAVES naCRIANÇA.IT: Non usare mai un sistema disicurezza per bambini rivoltoall'indietro su un sedile protetto daAIRBAG ATTIVO di fronte ad esso:pericolo di MORTE o LESIONIGRAVI per il BAMBINO!EL: ΠΟΤΕ μη χρησιμοποιείτε παιδικόκάθισμα ασφαλείας με φορά προς ταπίσω σε κάθισμα που προστατεύεταιαπό μετωπικό ΕΝΕΡΓΟ ΑΕΡΟΣΑΚΟ,διότι το παιδί μπορεί να υποστείΘΑΝΑΣΙΜΟ ή ΣΟΒΑΡΟΤΡΑΥΜΑΤΙΣΜΟ.


PL: NIE WOLNO montować fotelikadziecięcego zwróconego tyłem dokierunku jazdy na fotelu, przedktórym znajduje się WŁĄCZONAPODUSZKA POWIETRZNA.Niezastosowanie się do tegozalecenia może być przyczynąŚMIERCI lub POWAŻNYCHOBRAŻEŃ u DZIECKA.TR: Arkaya bakan bir çocuk emniyetsistemini KESİNLİKLE önünde birAKTİF HAVA YASTIĞI ilekorunmakta olan bir koltuktakullanmayınız. ÇOCUK ÖLEBİLİRveya AĞIR ŞEKİLDEYARALANABİLİR.UK: НІКОЛИ не використовуйтесистему безпеки для дітей, щовстановлюється обличчям назад,на сидінні з УВІМКНЕНОЮПОДУШКОЮ БЕЗПЕКИ, інакше цеможе призвести до СМЕРТІ чиСЕРЙОЗНОГО ТРАВМУВАННЯДИТИНИ.HU: SOHA ne használjon hátrafelénéző biztonsági gyerekülést előlrőlAKTÍV LÉGZSÁKKAL védett ülésen,mert a GYERMEK HALÁLÁT vagyKOMOLY SÉRÜLÉSÉT okozhatja.

HR: NIKADA nemojte koristiti sustavzadržavanja za djecu okrenut premanatrag na sjedalu s AKTIVNIMZRAČNIM JASTUKOM ispred njega,to bi moglo dovesti do SMRTI iliOZBILJNJIH OZLJEDA za DIJETE.SL: NIKOLI ne nameščajte otroškegavarnostnega sedeža, obrnjenega vnasprotni smeri vožnje, na sedež zAKTIVNO ČELNO ZRAČNOBLAZINO, saj pri tem obstajanevarnost RESNIH ali SMRTNIHPOŠKODB za OTROKA.SR: NIKADA ne koristiti bezbednosnisistem za decu u kome su decaokrenuta unazad na sedištu saAKTIVNIM VAZDUŠNIMJASTUKOM ispred sedišta zato štoDETE može da NASTRADA ili da seTEŠKO POVREDI.MK: НИКОГАШ не користете детскоседиште свртено наназад наседиште заштитено со АКТИВНОВОЗДУШНО ПЕРНИЧЕ пред него,затоа што детето може ДА ЗАГИНЕили да биде ТЕШКО ПОВРЕДЕНО.BG: НИКОГА не използвайтедетска седалка, гледаща назад,върху седалка, която е защитена

чрез АКТИВНА ВЪЗДУШНАВЪЗГЛАВНИЦА пред нея - може дасе стигне до СМЪРТ илиСЕРИОЗНО НАРАНЯВАНЕ наДЕТЕТО.RO: Nu utilizaţi NICIODATĂ un scaunpentru copil îndreptat spre partea dinspate a maşinii pe un scaun protejatde un AIRBAG ACTIV în faţa sa;acest lucru poate duce la DECESULsau VĂTĂMAREA GRAVĂ aCOPILULUI.CS: NIKDY nepoužívejte dětskýzádržný systém instalovaný protisměru jízdy na sedadle, které jechráněno před sedadlem AKTIVNÍMAIRBAGEM. Mohlo by dojít kVÁŽNÉMU PORANĚNÍ nebo ÚMRTÍDÍTĚTE.SK: NIKDY nepoužívajte detskúsedačku otočenú vzad na sedadlechránenom AKTÍVNYM AIRBAGOM,pretože môže dôjsť k SMRTI aleboVÁŽNYM ZRANENIAM DIEŤAŤA.LT: JOKIU BŪDU nemontuokite atgalatgręžtos vaiko tvirtinimo sistemossėdynėje, prieš kurią įrengta AKTYVIORO PAGALVĖ, nes VAIKAS GALIŽŪTI arba RIMTAI SUSIŽALOTI.


LV: NEKĀDĀ GADĪJUMĀneizmantojiet uz aizmuguri vērstubērnu sēdeklīti sēdvietā, kas tiekaizsargāta ar tās priekšā uzstādītuAKTĪVU DROŠĪBAS SPILVENU, jopretējā gadījumā BĒRNS var gūtSMAGAS TRAUMAS vai IET BOJĀ.ET: ÄRGE kasutage tahapoolesuunatud lapseturvaistet istmel, milleees on AKTIIVSE TURVAPADJAGAkaitstud iste, sest see võibpõhjustada LAPSE SURMA võiTÕSISE VIGASTUSE.MT: QATT tuża trażżin għat-tfal lijħares lejn in-naħa ta’ wara fuq sitprotett b’AIRBAG ATTIV quddiemu;dan jista’ jikkawża l-MEWT jewĠRIEĦI SERJI lit-TFAL.Beyond the warning required byECE R94.02, for safety reasons aforward-facing child restraint systemmust only be used subject to theinstructions and restrictions in thetable 3 66.The airbag label is located on bothsides of the front passenger sun visor.Airbag deactivation 3 62.

Front airbag systemThe front airbag system consists ofone airbag in the steering wheel andone in the instrument panel on thefront passenger side. These can beidentified by the word AIRBAG.The front airbag system is triggered inthe event of a front-end impact of acertain severity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and head ofthe front seat occupantsconsiderably.

9 Warning

Optimum protection is onlyprovided when the seat is in theproper position.Seat position 3 46.Keep the area in which the airbaginflates clear of obstructions.Fit the seat belt correctly andengage securely. Only then is theairbag able to protect.

Side airbag system


The side airbag system consists of anairbag in each front seat backrest.This can be identified by the wordAIRBAG.The side airbag system is triggered inthe event of a side impact of a certainseverity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and pelvis inthe event of a side-on collisionconsiderably.

9 Warning

Keep the area in which the airbaginflates clear of obstructions.

NoticeOnly use protective seat covers thathave been approved for the vehicle.Be careful not to cover the airbags.

Curtain airbag systemThe curtain airbag system consists ofan airbag in the roof frame on eachside. This can be identified by theword AIRBAG on the roof pillars.The curtain airbag system is triggeredin the event of a side-on impact of acertain severity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the head in the event of aside-on impact considerably.

9 Warning

Keep the area in which the airbaginflates clear of obstructions.The hooks on the handles in theroof frame are only suitable forhanging up light articles ofclothing, without coat hangers. Donot keep any items in theseclothes.


Airbag deactivationThe front passenger airbag systemmust be deactivated for child restraintsystem on the passenger seataccording to the instructions in thetable 3 66. The side airbag andcurtain airbag systems, the beltpretensioners and all driver airbagsystems will remain active.

The front passenger airbag systemcan be deactivated via a key-operated switch on the right side ofthe instrument panel.

Use the ignition key to choose theposition:*OFF : front passenger airbag is

deactivated and will notinflate in the event of acollision. Control indicator*OFF illuminatescontinuously in the centreconsole

VON : front passenger airbag isactive

9 Danger

Deactivate passenger airbag onlyin combination with the use of achild restraint system, subject tothe instructions and restrictions inthe table 3 66.Otherwise, there is a risk of fatalinjury for a person occupying aseat with a deactivated frontpassenger airbag.

If the control indicator V illuminatesfor approx. 60 seconds after theignition is switched on, the frontpassenger airbag system will inflatein the event of a collision.If both control indicators areilluminated at the same time, there isa system failure. The status of thesystem is not discernible, thereforeno person is allowed to occupy thefront passenger seat. Contact aworkshop immediately.Consult a workshop immediately ifneither of the two control indicatorsare illuminated.Change status only when the vehicleis stopped with the ignition off.


Status remains until the next change.Control indicator for airbagdeactivation 3 108.

Child restraintsChild restraint systems

9 Danger

If using a rear-facing child restraintsystem on the front passengerseat, the airbag system for thefront passenger seat must bedeactivated. This also applies tocertain forward-facing childrestraint systems as indicated inthe tables 3 66.

Airbag deactivation 3 62, Airbag label3 57.We recommend a child restraintsystem which is tailored specifically tothe vehicle. For further information,contact your workshop.When a child restraint system is beingused, pay attention to the followingusage and installation instructionsand also those supplied with the childrestraint system.

Always comply with local or nationalregulations. In some countries, theuse of child restraint systems isforbidden on certain seats.Child restraint systems can befastened with:● Three-point seat belt● ISOFIX brackets● Top-tether

Three-point seat beltChild restraint systems can befastened by using a three-point seatbelt. Depending on the size of theused child restraint systems, up tothree child restraint systems can beattached to the rear seats 3 66.


ISOFIX brackets

Fasten vehicle-approved ISOFIXchild restraint systems to the ISOFIXmounting brackets. Specific vehicleISOFIX child restraint systempositions are marked in the ISOFIXtable 3 66.ISOFIX mounting brackets areindicated by a label on the backrest.An i-Size child restraint system is anuniversal ISOFIX child restraintsystem according UN Regulation No.129.All i-Size child restraint systems canbe used on any vehicle seat suitablefor i-Size, i-Size table 3 66.

Either a Top-tether strap or a supportleg must be used in addition to theISOFIX mounting brackets.

i-Size child seats and vehicle seatswith i-Size approval are marked withi-Size symbol, see illustration.

Top-tether fastening eyesTop-tether fastening eyes are markedwith the symbol : for a child seat.

In addition to the ISOFIX mountingbrackets, fasten the Top-tether strapto the Top-tether fastening eyes. Thestrap must run between the two guiderods of the head restraint.ISOFIX child restraint systems ofuniversal category positions aremarked in the table by IUF 3 66.

Selecting the right systemThe rear seats are the mostconvenient location to fasten a childrestraint system.Children should travel facingrearwards in the vehicle as long aspossible. This makes sure that the


child's backbone, which is still veryweak, is under less strain in the eventof an accident.Suitable are restraint systems thatcomply with valid UN ECEregulations. Check local laws andregulations for mandatory use of childrestraint systems.The following child restraints arerecommended for the followingweight classes:Maxi Cosi Cabriofix for children up to13 kg for group 0, group 0+ and DuoPlus for children from 13 kg to 18 kgin group I.Ensure that the child restraint systemto be installed is compatible with thevehicle type.Ensure that the mounting location ofthe child restraint system within thevehicle is correct, see followingtables.Allow children to enter and exit thevehicle only on the side facing awayfrom the traffic.When the child restraint system is notin use, secure the seat with a seat beltor remove it from the vehicle.

NoticeDo not affix anything on the childrestraint systems and do not coverthem with any other materials.A child restraint system which hasbeen subjected to stress in anaccident must be replaced.


Child restraint installation locationsPermissible options for fastening a child restraint system with a three-point seat belt

Weight and age classOn front passenger seat

On rear outboard seats On rear centre seatactivated airbag deactivated airbag

Group 0: up to 10 kgor approx. 10 months

X U1,2 U/L3 U

Group 0+: up to 13 kgor approx. 2 years

X U1,2 U/L3 U

Group I: 9 to 18 kgor approx. 8 months to 4 years

X U1,2 U/L3,4 U4

Group II: 15 to 25 kgor approx. 3 to 7 years

U1,2 X U/L3,4 U4

Group III: 22 to 36 kgor approx. 6 to 12 years

U1,2 X U/L3,4 U4

U : universal suitability in conjunction with three-point seat beltL : suitable for particular child restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories. The

child restraint system must be approved for the specific vehicle type (refer to the vehicle type list of the child restraintsystem)

X : no child restraint system permitted in this weight class1 : move seat forwards as far as necessary and adjust seat backrest inclination as far as necessary to a vertical position

to ensure that the belt runs forwards from the upper anchorage point

Seats, restraints 672 : move seat height adjustment upwards as far as necessary and adjust seat backrest inclination as far as necessary

to a vertical position to ensure that the belt is tight on the buckle side3 : move the respective front seat ahead of the child restraint system forwards as far as necessary4 : adjust the respective headrest as necessary or remove if required

Permissible options for fitting an ISOFIX child restraint system with ISOFIX brackets

Weight and age class Size class Fixture

On front passenger seatOn rearoutboard seats

On rearcentre seat

activatedairbag

deactivatedairbag

Group 0: up to 10 kgor approx. 10 months

G ISO/L2 X X X X

F ISO/L1 X X X X

E ISO/R1 X X IL3 X

Group 0+: up to 13 kgor approx. 2 years

E ISO/R1 X X IL3 X

D ISO/R2 X X IL3 X

C ISO/R3 X X IL3 X

Group I: 9 to 18 kgor approx. 8 months to 4 years

D ISO/R2 X X IL3,4 X

C ISO/R3 X X IL3,4 X

B ISO/F2 X X IL, IUF3,4 X

B1 ISO/F2X X X IL, IUF3,4 X

A ISO/F3 X X IL, IUF3,4 X


Weight and age class Size class Fixture

On front passenger seatOn rearoutboard seats

On rearcentre seat

activatedairbag

deactivatedairbag

Group II: 15 to 25 kgor approx. 3 to 7 years

X X IL3,4 X

Group III: 22 to 36 kgor approx. 6 to 12 years

X X IL3,4 X

IL : suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories.The ISOFIX restraint system must be approved for the specific vehicle type (refer to the vehicle type list of the childrestraint system)

IUF : suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight classX : no ISOFIX child restraint system approved in this weight class1 : move seat forwards as far as necessary and adjust seat backrest inclination as far as necessary to a vertical position

to ensure that the belt runs forwards from the upper anchorage point2 : move seat height adjustment upwards as far as necessary and adjust seat backrest inclination as far as necessary

to a vertical position to ensure that the belt is tight on the buckle side3 : move the respective front seat ahead of the child restraint system forwards as far as necessary4 : adjust the respective headrest as necessary or remove if required

ISOFIX size class and seat deviceA – ISO/F3 : forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kgB – ISO/F2 : forward-facing child restraint system for smaller children in the weight class 9 to 18 kgB1 – ISO/F2X : forward-facing child restraint system for smaller children in the weight class 9 to 18 kgC – ISO/R3 : rear-facing child restraint system for children of maximum size in the weight class up to 18 kgD – ISO/R2 : rear-facing child restraint system for smaller children in the weight class up to 18 kgE – ISO/R1 : rear-facing child restraint system for young children in the weight class up to 13 kg


F– ISO/L1 : left lateral facing position child restraint system (carry-cot)G – ISO/L2 : right lateral facing position child restraint system (carry-cot)

Permissible options for fitting an i-Size child restraint system with ISOFIX brackets

On front passenger seatOn rear outboard seats On rear centre seatactivated airbag deactivated airbag

i-Size child restraint systems X X i - U X

i - U : suitable for i-Size 'universal' forward and rearward facing child restraint systemsX : seating position not suitable for i-Size 'universal' child restraint systems

70 Storage

Storage

Storage compartments ................ 70Glovebox ................................... 70Cupholders ................................ 70Front storage ............................. 71Armrest storage ......................... 71

Load compartment ....................... 72Load compartment cover ........... 78Rear floor storage cover ............ 79Lashing eyes ............................. 80Cargo management system ...... 81Safety net .................................. 83Warning triangle ........................ 85First aid kit ................................. 85

Roof rack system ......................... 86Roof rack ................................... 86

Loading information ..................... 87

Storage compartments

9 Warning

Do not store heavy or sharpobjects in the storagecompartments. Otherwise, thestorage compartment lid couldopen and vehicle occupants couldbe injured by objects being thrownaround in the event of hardbraking, a sudden change indirection or an accident.

Glovebox

The glovebox features a pen holder,a coin holder and an adapter for thelocking wheel nuts.The glovebox may also contain a CDplayer and a tool for removing thefuse cover with power connector.The glovebox should be closed whilstdriving.

Cupholders

Cupholders are located in the centreconsole.

Storage 71

Depending on the version,cupholders are located under a coverin the centre console. Slide coverbackwards.

Front storage

A storage compartment is locatednext to the steering wheel.

Armrest storageStorage under the front armrest

Press button to fold up the armrest.The armrest must be in rearmostposition.

72 Storage

Load compartmentDepending on the equipment, therear seat backrest is divided into twoor three parts. All parts can be foldeddown.Before folding rear seat backrests,execute the following if necessary:● 5-door hatchback: remove the

load compartment cover 3 78.● Sports Tourer: remove roller

blind 3 78.● Press and hold the catch to push

the head restraints down 3 45.● Remove the rear head restraints

to have the backrests fully rest onthe seat cushions 3 45.

Load compartment extension(two-part rear seat backrest), 5-door Hatchback

● Guide the seat belts of the outerseats through side supports toprotect them against damage.When folding the backrests, pullthe seat belts along with them.

● Pull the release lever on one orboth outer sides and fold downthe backrests onto the seatcushion.

● Take the seat belt out of the seatbackrest guide and put it behindthe retainer as shown in theillustration.

● To fold up, raise the backrestsand guide them into an uprightposition until they engageaudibly.

Storage 73

The backrests are properlyengaged when the red marks onboth sides near the release leverare no longer visible.

9 Warning

When folding up, ensure thatbackrests are securely locked inposition before driving. Failure todo so may result in personal injuryor damage to the load or vehicle inthe event of hard braking or acollision.

The seat belt of the centre seat couldbe blocked when the backrest isfolded up too quickly. To unlock theretractor, push in the seat belt or pullit out by approx. 20 mm then release.

Load compartment extension(three-part rear seat backrest), 5-door Hatchback● Fold up the rear armrest.

● Pull the loop and fold down thebackrest of the centre seat.


9 Warning

Take care when folding down theright outer seat backrest if thecentre seat backrest is alreadyfolded down. Risk of injury due tobolt protruding from the inner sideof the backrest.

74 Storage

● Guide the seat belts of the outerseats through side supports toprotect them against damage.When folding the backrests, pullthe seat belts along with them.

● Take the seat belt out of the seatbackrest guide and put it behindthe retainer as shown in theillustration.



9 Warning



Storage 75

Load compartment extension(two-part rear seat backrest),Sports Tourer

● Insert latch plates of the outerseat belts into side holder toprotect the belts against damage,see illustration.




9 Warning


76 Storage


Load compartment extension(three-part rear seat backrest),Sports Tourer● Fold up the rear centre armrest.

● Pull the loop and fold down thebackrest of the centre seat.

● Insert latch plates of the outerseat belts into side holder toprotect the belts against damage,see illustration.


9 Warning

Take care when folding down theright outer seat backrest if thecentre seat backrest is alreadyfolded down. Risk of injury due tobolt protruding from the inner sideof the backrest.

Storage 77

● Alternatively fold seat backrestsfrom the load compartment: pullswitch on left or right sidewall ofthe load compartment to fold thecorresponding part of the rearseat backrest.

9 Warning

Take care when operating the rearbackrests from the loadcompartment. The backrest isfolded with considerable power.Risk of injury, particularly tochildren.

Ensure that nothing is attached tothe rear seats or located on theseat cushion.



9 Warning



78 Storage

Load compartment coverDo not place any objects on the cover.

5-door hatchback

Removing

Unhook retaining straps from tailgate.

Lift cover at the rear and push itupwards at the front.Remove the cover.

FittingEngage cover in side guides and folddownwards. Attach retaining straps totailgate.

Sports Tourer

Closing roller blindPull the roller blind using the handletowards the rear and upwards until itengages in the sideward retainers.

Opening roller blind

Pull the handle at the end of the rollerblind to the rear and downwards. Itrolls up automatically.

Storage 79

Removing roller blind

Open the roller blind.Pull the release lever on the right sideup and hold it. Lift the roller blind firston the right side and remove fromretainers.

The removed roller blind can bestored under the rear floor cover asshown in the illustration. Insert the leftside of the rolled up cover first in thefront right recess, pull the releaselever up and insert the right side in thefront left recess.Rear floor storage cover 3 79.

Installing roller blindInsert the left side of the roller blind inthe recess, then pull the release leverup and hold and insert the right sideof the roller blind in the recess andengage.

Rear floor storage coverRear floor cover

5-door Hatchback

The rear floor cover can be removed.Raise cover at the rear and slightlyrotate at one side before removing.

80 Storage

Sports Tourer

Pull the handle and fold the rear partof the cover forward.

Set up the folded cover upright behindthe rear seat backrests.

Lashing eyesThe lashing eyes are designed tosecure items against slippage, e.g.using lashing straps or luggage net.

5-door HatchbackFirst remove the rear floor storagecover to get access to the lashingeyes.

On vehicles equipped with a sparewheel, the front lashing eyes arelocated at the sidewalls.

On vehicles equipped with tyre repairkit, the front lashing eyes are locatedunderneath the rear floor coverbehind the rear seats. To get accessto the lashing eyes, open theperforated parts of the cover by usingthe screwdriver. Vehicle tools 3 236.Stick the screwdriver through thecover as shown in the illustration andfold up the perforated part of thecover.Fold up the lashing eyes by using thescrewdriver.

Storage 81

Sports Tourer

Front and rear lashing eyes arelocated at the sidewalls. Fold up thelashing eyes to use and fold downwhen not required.

Cargo management systemThe FlexOrganizer is a flexiblesystem for dividing up the loadcompartment.The system consists of:● adapters● mesh pockets● hooks

● service box● strap set

The components are fitted in rails onboth side panels using adapters andhooks.

Installation of adapters in the rails

Fold open the handle plate, insert theadapter into the upper and lowergroove of the rail and move to therequired position. Turn the handleplate upwards to lock the adapter. Toremove, turn the handle plate downand move out of the rail.

Variable partition net

Insert adapters into the requiredposition in the rails. Stick together thehalves of the net rods.To install, push rods together a littleand insert into the relevant openingsin the adapters.To remove, press the net rodstogether and remove from theadapters.

82 Storage

Net pocket

Insert adapters into the requiredposition in the rails. The net pocketcan be suspended from the adapters.

Installation of hooks in the rails

Insert the hook in the desired positionfirst in the upper groove of the rail andthen press in the lower groove. Toremove, first pull out of the uppergroove.

Service box

Install two hooks in the upper rail.Insert the upper brackets of the boxfrom above into the hooks.

Storage 83

Alternatively install both hooks in thelower rail. Plug in the lower bracketsof the box from above into the lowerhooks.

Strap set

Insert the adapters of the strap set ina rail. Make sure that the belt is nottwisted.The strap set has two locks to open.The belt can be tightened.

Safety netThe safety net is available on theSports tourer and can be installedbehind the rear seats or, if the rearseat backrests are folded, behind thefront seats.Passengers must not be transportedbehind the safety net.

Installation

Behind the rear seats

● There are installation openingson both sides in the roof frameabove the rear seats: suspend

and engage rod of net at oneside, compress rod and suspendand engage at the other side.

● Attach the hooks of safety netstraps in loops underneath therear floor cover behind the rearseats. To get access to the loops,open the perforated parts in thefloor cover on both sides by usingthe screwdriver and fold up theloops. Attach the hooks to theloops.

● Tension both straps by pulling atthe loose end.

● Rear seat backrests must beraised up.

84 Storage

Behind the front seats

● There are installation openingson both sides in the roof frameabove the front seats: suspendand engage rod of net at oneside, compress rod and suspendand engage at the other side.

● Attach hooks of safety net strapsto loops in the floor in front of therear seats. To get access to theloops, push in the perforatedparts in the floor cover on bothsides. Attach the hooks to theloops.

● Tension both straps by pulling atthe loose end.

● Push down head restraints andfold down rear seat backrests3 72.

Removal

Pull the flap at the tightener on bothsides to release the straps. Detachhooks from the eyes.Unhook the safety net rods from thebrackets in the roof frame.Roll up the net and secure with astrap.

StowingThe removed safety net can be storedunder the rear floor cover 3 79.

Storage 85

Warning triangle5-door hatchback

Stow the warning triangle in therecess in front of the tailgate.

Sports Tourer

Stow the warning triangle in therecess under the rear floor cover onthe right or left side.

First aid kitStow the first aid kit in thecompartment in the left side wall.

Illustration shows 5-door Hatchback.To open the compartment, disengagecover and open.

Illustration shows Sports Tourer.

86 Storage

To open the cover turn knob. Roof rack systemRoof rackFor safety reasons and to avoiddamage to the roof, the vehicleapproved roof rack system isrecommended. For furtherinformation contact your workshop.

Mounting roof rack

5-door Hatchback, Sports Tourer

Open all doors.Mounting points are located in eachdoor frame of the vehicle body.

Fasten the roof rack according to theinstallation instructions delivered withthe roof rack.Remove the roof rack when not inuse.

9 Warning

Sports TourerRoof railings are a styling elementonly and not designed to carry anyload. Installation of roof racks orother accessory is not permitted.Use the designated mountingpoints in the door framesexclusively.

Storage 87

Loading information

● Heavy objects in the loadcompartment should be placedagainst the seat backrests. Makesure that the backrests aresecurely engaged, i.e. no longershowing the red markings on theside near the release lever. Ifobjects can be stacked, heavierobjects should be placed at thebottom.

● Secure objects with lashingstraps attached to lashing eyes3 80.

● Secure loose objects in the loadcompartment to prevent themfrom sliding.

● When transporting objects in theload compartment, the backrestsof the rear seats must not beangled forward.

● Do not allow the load to protrudeabove the upper edge of thebackrests.

● Sports Tourer: install safety netwhen transporting objects in theload compartment.

● Do not place any objects on theload compartment cover or theinstrument panel, and do notcover the sensor on top of theinstrument panel.

● The load must not obstruct theoperation of the pedals, parkingbrake and gear selector lever, orhinder the freedom of movementof the driver. Do not place anyunsecured objects in the interior.

● Do not drive with an open loadcompartment.

9 Warning

Always make sure that the load inthe vehicle is securely stowed.Otherwise objects can be thrownaround inside the vehicle andcause personal injury or damageto the load or car.

● The payload is the differencebetween the permitted grossvehicle weight (see identificationplate 3 263) and the EC kerbweight.To calculate the payload, enterthe data for your vehicle in theweights table at the front of thismanual.The EC kerb weight includesweights for the driver (68 kg),luggage (7 kg) and all fluids (fueltank 90% full).Optional equipment andaccessories increase the kerbweight.

● Driving with a roof load increasesthe sensitivity of the vehicle tocross-winds and has a

88 Storage

detrimental effect on vehiclehandling due to the vehicle'shigher centre of gravity.Distribute the load evenly andsecure it properly with retainingstraps. Adjust the tyre pressureand vehicle speed according tothe load conditions. Check andretighten the straps frequently.Do not drive faster than 75 mph.The permissible roof load is75 kg. The roof load is thecombined weight of the roof rackand the load.

Instruments and controls 89

Instruments andcontrols

Controls ....................................... 90Steering wheel adjustment ........ 90Steering wheel controls ............. 90Heated steering wheel ............... 91Horn ........................................... 91Windscreen wiper/washer ......... 91Rear window wiper/washer ....... 93Outside temperature .................. 94Clock ......................................... 94Power outlets ............................. 96Power connector ....................... 97Ashtrays .................................... 98

Warning lights, gauges and indi‐cators ......................................... 100

Instrument cluster .................... 100Speedometer ........................... 103Odometer ................................ 104Trip odometer .......................... 104Tachometer ............................. 105Fuel gauge .............................. 105Engine coolant temperaturegauge ..................................... 105

Service display ........................ 106Control indicators .................... 107

Turn signal ............................... 107Seat belt reminder ................... 107Airbag and belt tensioners ....... 108Airbag deactivation .................. 108Charging system ..................... 108Malfunction indicator light ........ 109Brake and clutch system ......... 109Electric parking brake .............. 109Electric parking brake fault ...... 109Antilock brake system (ABS) ... 110Gear shifting ............................ 110Following distance ................... 110Lane keep assist ..................... 110Electronic Stability Control off . 110Electronic Stability Control andTraction Control system ......... 110

Traction Control system off ..... 111Preheating ............................... 111Tyre pressure monitoringsystem .................................... 111

Engine oil pressure .................. 111Low fuel ................................... 111Immobiliser .............................. 112Exterior light ............................ 112High beam ............................... 112High beam assist ..................... 112LED headlights ........................ 112Fog light ................................... 112Rear fog light ........................... 112Cruise control .......................... 112

Vehicle detected ahead ........... 112Speed limiter ........................... 112Traffic sign assistant ................ 113Door open ................................ 113

Information displays ................... 113Driver Information Centre ........ 113Info display .............................. 118

Vehicle messages ...................... 120Warning chimes ....................... 121Battery voltage ........................ 122

Vehicle personalisation .............. 122OnStar ....................................... 128

90 Instruments and controls

ControlsSteering wheel adjustment

Unlock lever, adjust steering wheel,then engage lever and ensure it isfully locked.Do not adjust steering wheel unlessvehicle is stationary and steeringwheel lock has been released.

Steering wheel controlsDriver Information Centre, somedriver assistance systems,Infotainment system and a connectedmobile phone can be operated via thecontrols on the steering wheel.

The illustrations show differentversions.

Driver Information Centre 3 113.Driver assistance systems 3 178.Further information is available in theInfotainment manual.


Heated steering wheel

Activate heating by pressing *.Activation is indicated by the LED inthe button.

The recommended grip areas of thesteering wheel are heated quickerand to a higher temperature than theother areas.Heating is operational when theengine is running and during anAutostop.Stop-start system 3 159.

Horn

Press j.

Windscreen wiper/washerWindscreen wiper with adjustablewiper interval

HI : fastLO : slowINT : interval wipingOFF : off

For a single wipe when thewindscreen wiper is off, press thelever downwards to position 1x.Do not use if the windscreen is frozen.Switch off in car washes.


Adjustable wiper interval

Wiper lever in position INT.Turn the adjuster wheel to adjust thedesired wipe interval:short interval : turn adjuster

wheel upwardslong interval : turn adjuster

wheel downwards

Windscreen wiper with rainsensor

HI : fastLO : slowAUTO : automatic wiping with rain

sensorOFF : off

In AUTO position, the rain sensordetects the amount of water on thewindscreen and automaticallyregulates the frequency of thewindscreen wiper.For a single wipe when thewindscreen wiper is off, press thelever downwards to position 1x.Do not use if the windscreen is frozen.

Switch off in car washes.

Adjustable sensitivity of the rainsensor

Wiper lever in position AUTO.Turn the adjuster wheel to adjust thesensitivity:low sensitivity : turn adjuster

wheel downwardshigh sensitivity : turn adjuster

wheel upwards


Keep the sensor free from dust, dirtand ice.Rain sensor function can be activatedor deactivated in the Vehiclepersonalisation.Select the relevant setting in Settings,I Vehicle in the Info-Display.Info-Display 3 118.Vehicle personalisation 3 122.

Windscreen washer

Pull lever. Washer fluid is sprayedonto the windscreen and the wiperwipes a few times.Washer fluid 3 216.

Rear window wiper/washer

Turn outer cap to activate the rearwindow wiper:ON : continuous operationINT : intermittent operationOFF : off

Do not use if the rear window isfrozen.Switch off in car washes.The rear window wiper comes onautomatically when the windscreenwiper is switched on and reverse gearis engaged.


Activation or deactivation of thisfunction can be changed in the menuSettings in the Info-Display.Vehicle personalisation 3 122.

Rear window washer

Push lever.Washer fluid is sprayed onto the rearwindow and the wiper wipes a fewtimes.The rear window washer system isdeactivated when the fluid level islow.Washer fluid 3 216

Outside temperatureA drop in temperature is indicatedimmediately and a rise in temperatureafter a time delay.

Illustration shows an example.

If outside temperature drops to 3 °C,a warning message is displayed in theDriver Information Centre.

9 Warning

The road surface may already beicy even though the displayindicates a few degrees above 0°C.

ClockDate and time are shown in theInfo-Display.Info-Display 3 118.


Graphic-Info-DisplayPress MENU to open the respectiveaudio menu.

Select Time and Date.

Set TimeSelect Set Time to enter therespective submenu.Select Auto Set at the bottom of thescreen. Activate either On - RDS orOff (Manual).If Off (Manual) is selected, adjusthours and minutes.Repeatedly select 12-24 HR at thebottom of the screen to choose a timemode.If the 12-hour mode is selected, athird column for AM and PM selectionis displayed. Select the desiredoption.

Set DateSelect Set Date to enter therespective submenu.Select Auto Set at the bottom of thescreen. Activate either On - RDS orOff (Manual).If Off (Manual) is selected, adjust thedate settings.

7'' Colour-Info-DisplayPress ; and then select Settings.Select Time and Date to display therespective submenu.

Set Time FormatTo select the desired time format,touch the screen buttons 12 h or 24 h.

Set Date FormatTo select the desired date format,select Set Date Format and choosebetween the available options in thesubmenu.

Auto SetTo choose whether time and date areto be set automatically or manually,select Auto Set.For time and date to be setautomatically, select On - RDS.For time and date to be set manually,select Off - Manual. If Auto Set is setto Off - Manual, the submenu itemsSet Time and Set Date becomeavailable.

Set time and dateTo adjust the time and date settings,select Set Time or Set Date.Touch + and - to adjust the settings.


8'' Colour-Info-DisplayPress ; and then select theSettings icon.Select Time and Date.

Set timeSelect Set Time to enter therespective submenu.

Select Auto Set at the bottom of thescreen. Activate either On - RDS orOff - Manual.If Off - Manual is selected, adjusthours and minutes by touching n oro.

Touch 12-24 Hr on the right side of thescreen to select a time mode.If 12-hour mode is selected, a thirdcolumn for AM and PM setting isdisplayed. Select the desired option.

Set dateSelect Set Date to enter therespective submenu.NoticeIf date information is automaticallyprovided, this menu item is notavailable.

Select Auto Set at the bottom of thescreen. Activate either On - RDS orOff - Manual.If Off - Manual is selected, adjust thedate by touching n or o.

Clock displaySelect Clock Display to enter therespective submenu.To turn off the digital clock display inthe menus, select Off.

Power outlets

A 12 Volt power outlet is located in thecentre console.


Sports Tourer: A 12 Volt power outletis located at the left sidewall in theload compartment.Do not exceed the maximum powerconsumption of 120 watts.With ignition off, the power outlet isdeactivated. Additionally, the poweroutlet is deactivated in the event oflow vehicle battery voltage.Electrical accessories that areconnected must comply with theelectromagnetic compatibilityrequirements laid down inDIN VDE 40 839.Do not connect any current-deliveringaccessories, e.g. electrical chargingdevices or batteries.Do not damage the outlets by usingunsuitable plugs.Stop-start system 3 159.

USB charging port

Two USB ports for charging devicesonly are located in the back of thecentre console.Each socket provides 2.1 Ampere atfive Volts.NoticeThe sockets must always be keptclean and dry.

Power connector

The power connector (PowerFlexBar) is attached on the instrumentpanel fuse box cover. A fragrancediffuser (AirWellness) or a phoneholder can be attached to the powerconnector.Further information regarding phoneholder is available in the Infotainmentmanual.


Fragrance diffuser

1. Attach fragrance diffuser to upperside of the power connector (1)and swivel downwards to engage(2).

2. Press front button to activate anddeactivate the fragrance diffuser.LED indicates activation.

3. To remove fragrance diffuser,press diffuser downwards andswivel backwards.

4. To replace fragrance pad, shiftcartridge upwards and remove it.

5. Replace fragrance pad.

Ashtrays

Caution

To be used only for ash and not forcombustible rubbish.


A portable ashtray can be placed inthe cupholders.


Warning lights, gaugesand indicatorsInstrument clusterDepending on the version, twoinstrument clusters are available:


Midlevel instrument cluster


Uplevel instrument cluster


Overview

O Turn signal 3 107

X Seat belt reminder 3 107

v Airbag and belt tensioners3 108

V Airbag deactivation 3 108

p Charging system 3 108

Z Malfunction indicator light3 109

R Brake and clutch system 3 109

m Electric parking brake 3 109

j Electric parking brake fault3 109

u Antilock brake system (ABS)3 110

R Gear shifting 3 110

E Following distance 3 110

a Lane keep assist 3 110

a Electronic Stability Control off3 110

b Electronic Stability Control andTraction Control system 3 110

k Traction Control system off3 111

! Preheating 3 111

w Tyre pressure monitoringsystem 3 111

I Engine oil pressure 3 111

Y Low fuel 3 111

d Immobiliser 3 112

8 Exterior light 3 112

C High beam 3 112

f High beam assist 3 112

f LED headlights 3 112

> Fog light 3 112

ø Rear fog light 3 112

m Cruise control 3 112

A Vehicle detected ahead 3 112

L Speed limiter 3 112

L Traffic sign assistant 3 113

h Door open 3 113

Speedometer

Indicates vehicle speed.


Odometer

The total recorded distance isdisplayed in miles.

Trip odometerThe recorded distance since the lastreset is displayed on the trip computerpage. Two trip odometer areselectable for different trips.Trip odometer counts up to9,999 miles and then restarts at 0.

Midlevel instrument cluster

Select Info page ; by pressingMenu on the turn signal lever. Turnadjuster wheel on turn signal leverand select Trip 1 or Trip 2. Each tripodometer can be reset separately bypressing SET/CLR on the turn signallever for a few seconds on therespective page.

Uplevel instrument cluster

Select Info page J on main menu.Choose page Trip A or Trip B bypressing o on the steering wheel.Each trip odometer can be resetseparately when ignition is on: selectrespective page, press >. Confirm bypressing 9.Driver Information Centre 3 113.


Tachometer

Displays the engine speed.Drive in a low engine speed range foreach gear as much as possible.

Caution

If the needle is in the red warningzone, the maximum permittedengine speed is exceeded. Engineat risk.

Fuel gauge

Displays the level in the fuel tank.The arrow indicates the vehicle sidewhere the fuel filler flap is located.Control indicator Y illuminates if thelevel in the tank is low. Refuelimmediately if it flashes.Never run the fuel tank dry.Because of the fuel remaining in thetank, the top-up quantity may be lessthan the specified fuel tank capacity.

Engine coolant temperaturegauge

Displays the coolant temperature.50 : engine operating

temperature not yetreached

centralarea

: normal operatingtemperature

130 : temperature too high


Caution

If engine coolant temperature istoo high, stop vehicle, switch offengine. Danger to engine. Checkcoolant level.

Service displayThe engine oil life system informswhen to change the engine oil andfilter. Based on driving conditions, theinterval at which an engine oil andfilter change will be indicated can varyconsiderably.

The remaining oil life duration menuis displayed in the Driver InformationCentre 3 113.

On Midlevel display select theSettings Menu by pressing MENU onthe turn signal lever. Turn the adjusterwheel to select the Remaining OilLife page.

On Uplevel display select Info Menuby pressing p on steering wheel.Press P to select Remaining OilLife page.Remaining oil life duration is indicatedin percentage.

ResetOn Midlevel display press SET/CLRon turn signal lever for severalseconds to reset. The ignition must beswitched on but engine not running.On Uplevel display press > onsteering wheel to open the subfolder.Select Reset and confirm by pressing


9 for several seconds. The ignitionmust be switched on but engine notrunning.The system must be reset every timethe engine oil is changed to allowproper functionality. Seek theassistance of a workshop.

Next serviceWhen the system has calculated thatengine oil life has been diminished,Change Engine Oil Soon appears inthe Driver Information Centre. Haveengine oil and filter changed by aworkshop within one week or300 miles (whichever occurs first).Service information 3 260.

Control indicatorsThe control indicators described arenot present in all vehicles. Thedescription applies to all instrumentversions. Depending on theequipment, the position of the controlindicators may vary. When theignition is switched on, most controlindicators will illuminate briefly as afunctionality test.

The control indicator colours mean:red : danger, important reminderyellow : warning, information, faultgreen : confirmation of activationblue : confirmation of activationwhite : confirmation of activation

See all control indicators on differentinstrument clusters 3 100.

Turn signalO illuminates or flashes green.

Illuminates brieflyThe parking lights are switched on.

FlashesA turn signal or the hazard warningflashers are activated.Rapid flashing: failure of a turn signallight or associated fuse, failure of turnsignal light on trailer.Bulb replacement 3 219, Fuses3 230.Turn signals 3 138.

Seat belt reminderSeat belt reminder on front seatsX for driver's seat illuminates orflashes red in the instrument cluster.

k for front passenger seat illuminatesor flashes red in the roof console,when seat is occupied.

IlluminatesAfter the ignition has been switchedon until the seat belt has beenfastened.

FlashesAfter having started the engine for amaximum of 100 seconds until theseat belt has been fastened.


Seat belt status on rear seats(vehicles with Midlevel display)X illuminates or flashes white or greyin the Driver Information Centre, afterhaving started the engine.

Illuminates whiteSeat belt is unfastened.

Illuminates greySeat belt has been fastened.

Flashes white or greyFastened seat belt has beenunfastened.Fastening the seat belt 3 56.

Seat belt status on rear seats(vehicles with Uplevel display)X illuminates green or grey or flashesyellow in the Driver InformationCentre, after having started theengine.

Illuminates greySeat belt is unfastened.

Illuminates greenSeat belt has been fastened.

Flashes yellowFastened seat belt has beenunfastened.Fastening the seat belt 3 56.

Airbag and belt tensionersv illuminates red.When the ignition is switched on, thecontrol indicator illuminates forapprox. four seconds. If it does notilluminate, does not go out afterfour seconds or illuminates whilstdriving, there is a fault in the airbagsystem. Seek the assistance of aworkshop. The airbags and beltpretensioners may fail to trigger in theevent of an accident.Deployment of the belt pretensionersor airbags is indicated by continuousillumination of v.

9 Warning

Have the cause of the faultremedied immediately by aworkshop.

Belt pretensioners, airbag system3 55, 3 57.

Airbag deactivation

V illuminates yellow.The front passenger airbag isactivated.* illuminates yellow.The front passenger airbag isdeactivated.Airbag deactivation 3 62.

Charging systemp illuminates red.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.


Illuminates when the engine isrunningStop, switch off engine. Vehiclebattery is not charging. Enginecooling may be interrupted. Thebrake servo unit may cease to beeffective. Seek the assistance of aworkshop.

Malfunction indicator lightZ illuminates or flashes yellow.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunningFault in the emission control system.The permitted emission limits may beexceeded.On diesel engines the cleaningprocess of the diesel particle filter ispotentially not possible.Seek the assistance of a workshopimmediately.

Flashes when the engine isrunningFault that could lead to catalyticconverter damage. Ease up on theaccelerator until the flashing stops.Seek the assistance of a workshopimmediately.

Brake and clutch systemR illuminates red.The brake and clutch fluid level is toolow, when manual parking brake isnot applied 3 216.

9 Warning

Stop. Do not continue yourjourney. Consult a workshop.

Illuminates when the manual parkingbrake is applied and ignition isswitched on 3 173.

Electric parking brakem illuminates or flashes red.

IlluminatesElectric parking brake is applied3 173.

FlashesElectric parking brake is not fullyapplied or released. Depress thebrake pedal and attempt to reset thesystem by first releasing thenapplying the electric parking brake. Ifm remains flashing, do not drive andseek the assistance of a workshop.

Electric parking brake faultj illuminates or flashes yellow.

IlluminatesElectric parking brake is operatingwith degraded performance 3 173.

FlashesElectric parking brake is in servicemode. Stop vehicle, apply andrelease the electric parking brake toreset.


9 Warning

Have the cause of the faultremedied immediately by aworkshop.

Antilock brake system(ABS)u illuminates yellow.Illuminates for a few seconds after theignition is switched on. The system isready for operation when the controlindicator extinguishes.If the control indicator does not go outafter a few seconds, or if it illuminateswhile driving, there is a fault in theABS. The brake system remainsoperational but without ABSregulation.Antilock brake system 3 172.

Gear shiftingR or S with the number of the nexthigher or lower gear is indicated,when up- or down-shifting isrecommended.

Following distanceE indicates the following distancesetting of the alert timing sensitivityfor the forward collision alert usingfilled distance bars.Forward collision alert 3 181.

Lane keep assista illuminates green or yellow, orflashes yellow.

Illuminates greenThe system is switched on and readyto operate.

Illuminates yellowThe system approaches a detectedlane marking without using the turnsignal in that direction.

Flashes yellowThe system recognizes that the laneis departed significantly.Lane keep assist 3 201

Electronic Stability Controloffn illuminates yellow.The system is deactivated.

Electronic Stability Controland Traction Control systemb illuminates or flashes yellow.

IlluminatesA fault in the system is present.Continued driving is possible. Drivingstability, however, may deterioratedepending on road surfaceconditions.Have the cause of the fault remediedby a workshop.

FlashesThe system is actively engaged.Engine output may be reduced andthe vehicle may be brakedautomatically to a small degree.Electronic Stability Control 3 176,Traction Control system 3 175.


Traction Control system offk illuminates yellow.The system is deactivated.

Preheating! illuminates yellow.Preheating of Diesel engine isactivated. Only activates whenoutside temperature is low. Start theengine when control indicatorextinguishes.

Tyre pressure monitoringsystemw illuminates or flashes yellow.

IlluminatesTyre pressure loss. Stop immediatelyand check tyre pressure.

FlashesFault in system or tyre withoutpressure sensor mounted (e.g. sparewheel). After 60 to 90 seconds thecontrol indicator illuminatescontinuously. Consult a workshop.

Engine oil pressureI illuminates red.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunning

Caution

Engine lubrication may beinterrupted. This may result indamage to the engine and/orlocking of the drive wheels.

1. Depress clutch.2. Select neutral gear.3. Move out of the flow of traffic as

quickly as possible withoutimpeding other vehicles.

4. Switch off ignition.

9 Warning

When the engine is off,considerably more force is neededto brake and steer.During an Autostop, the brakeservo unit will still be operational.Do not remove key until vehicle isstationary, otherwise the steeringwheel lock could engageunexpectedly.

Check oil level before seekingassistance of a workshop 3 214.

Low fuelY illuminates or flashes yellow.

IlluminatesLevel in fuel tank is too low.

FlashesFuel used up. Refuel immediately.Never run the tank dry.Refuelling 3 203.Catalytic converter 3 165.


Bleeding the diesel fuel system3 218.

Immobiliserd flashes yellow.Fault in the immobiliser system. Theengine cannot be started.

Exterior light8 illuminates green.The exterior lights are on 3 132.

High beamC illuminates blue.Illuminated when high beam is on orduring headlight flash 3 133.

High beam assistf illuminates green.The high beam assist is activated,see LED headlights 3 134.

LED headlightsf illuminates or flashes yellow.

IlluminatesFault in the system.Seek the assistance of a workshop.

FlashesSystem is switched to symmetricallow beam.Control indicator f flashes for approx.four seconds after the ignition isswitched on as a reminder forsymmetrical headlight 3 134.

Fog light> illuminates green.The front fog lights are on 3 138.

Rear fog lightø illuminates yellow.The rear fog light is on 3 139.

Cruise controlm illuminates white or green.

Illuminates whiteThe system is on.

Illuminates greenCruise control is active. Set speed isindicated in the Driver InformationCentre.Cruise control 3 178.

Vehicle detected aheadA illuminates green or yellow.

Illuminates greenA vehicle ahead is detected in thesame lane.

Illuminates yellowThe distance to a preceding movingvehicle gets too small or whenapproaching another vehicle toorapidly.Forward collision alert 3 181.

Speed limiterL illuminates white or green.

Illuminates whiteThe system is on.


Illuminates greenSpeed limiter is active. Set speed isindicated near L symbol.Speed limiter 3 180.

Traffic sign assistantL displays detected traffic signs ascontrol indicator.Traffic sign assistant 3 197.

Door openh illuminates red.A door or the tailgate is open.

Information displaysDriver Information CentreThe Driver Information Centre islocated in the instrument cluster.Depending on the version and theinstrument cluster, the DriverInformation Centre is available asMidlevel display or Uplevel display.Driver Information Centre indicatesdepending on the equipment:● overall and trip odometer● vehicle information● trip/fuel information● driving economy information● vehicle and warning messages● audio and infotainment

information● phone information● navigation information● vehicle settings

Midlevel display

Main menus are:● Trip/fuel information, displayed

by ;, see description below.● Vehicle information, displayed

by ?, see description below.● Eco information, displayed by

@, see description below.Some of the displayed functions differwhen the vehicle is being driven or ata standstill and some functions areonly active when the vehicle is beingdriven.


Selecting menus and functionsThe menus and functions can beselected via the buttons on the turnsignal lever.

Press MENU to switch between themain menus or to return from asubmenu to the next higher menulevel.Turn the adjuster wheel to select asubmenu of the main menu or to seta numeric value.Press SET/CLR to select and confirma function.

Vehicle and service messages arepopped up in the Driver InformationCentre if required. Confirm messagesby pressing SET/CLR. Vehiclemessages 3 120.

Uplevel display

Main menus are:● Trip/fuel information, displayed

by Info, see description below.● Audio information, displayed by

Audio, see description below.● Phone information, displayed by

Phone, see description below.

● Navigation information,displayed by Navigation, seedescription below.

● Vehicle information, displayed byOptions, see description below.

Some of the displayed functions differwhen the vehicle is being driven or ata standstill and some functions areonly active when the vehicle is beingdriven.

Selecting menus and functionsThe menus and functions can beselected via the buttons on the rightside in the steering wheel.

Press p to open main menu page.


Select a main menu page with Q orP.Confirm a main menu page with 9.Once a main menu page is selected,press Q or P to select subpages.Press q to open a next folder of theselected subpage.Press Q or P to select functions orto set a numeric value, if required.Press 9 to select and confirm afunction.Once a main menu page is selected,this selection remains stored untilanother main menu page is selected.Subpages are changed by pressingP or Q.Vehicle and service messages arepopped-up in the Driver InformationCentre if required. Confirm messagesby pressing 9. Vehicle messages3 120.

Trip/fuel information menu, ;or InfoThe following list contains all possibleInfo Menu pages. Some may not beavailable for your particular vehicle.Depending on the display, somefunctions are symbolised.Turn the adjuster wheel or press Qor P to select a page:● Trip odometer 1/2 or A/B● Average fuel consumption● Average speed● Digital speed● Fuel range● Instantaneous fuel consumption● Remaining oil life● Tyre pressure● Traffic sign assistant● Following distance● Timer● Outside temperature

On Midlevel display the pagesRemaining Oil Life, Tyre Pressure,Traffic Sign Assistant and FollowingDistance are displayed in the Vehicleinformation menu, select ?.

Trip odometer 1/2 or A/BTrip odometer displays the currentdistance since a certain reset.Trip odometer counts up to a distanceof 9,999 miles then restarts at 0.To reset on Midlevel display, pressSET/CLR for a few seconds.To reset on Uplevel display, press >and confirm with 9.The information of trip odometer page1/A and 2/B can be reset separatelywhile the respective display is active.

Average Fuel ConsumptionDisplay of average consumption. Themeasurement can be reset at anytime and starts with a default value.To reset on Midlevel display, pressSET/CLR for a few seconds, onUplevel display, press > and confirmwith 9.


Average speedDisplay of average speed. Themeasurement can be reset at anytime.To reset on Midlevel display, pressSET/CLR for a few seconds, onUplevel display, press > and confirmwith 9.

Digital speedDigital display of the instantaneousspeed.

Fuel rangeRange is calculated from current fuellevel and current consumption. Thedisplay shows average values.After refuelling, the range is updatedautomatically after a brief delay.When the level in the fuel tank is low,a message appears on the displayand the control indicator Y in the fuelgauge illuminates.When the fuel tank must be refuelledimmediately, a warning messageappears and remains on the display.Additionally, the control indicator Y inthe fuel gauge flashes 3 111.

Instantaneous Fuel ConsumptionDisplay of the instantaneousconsumption.

Remaining Oil LifeIndicates an estimate of the oil'suseful life. The number in percentagemeans the remainder of current oil life3 106.

Tyre PressureChecks tyre pressure of all wheelsduring driving 3 239.

Traffic sign assistantDisplays the detected traffic signs forthe current route section 3 197.

Following DistanceDisplays the distance in seconds to apreceding moving vehicle 3 184. IfAdaptive cruise control is active thispage shows the following distancesetting instead.

TimerTo start and stop, press 9. To reset,press > and confirm reset.

Outside temperatureDisplay of current outsidetemperature.

Eco information menu, @● Top consumers● Economy trend● Eco index

On Uplevel display the pages TopConsumers, Economy Trend and Ecoindex, are displayed in the Trip/fuelinformation menu, select Info.

Top ConsumersList of top comfort consumerscurrently switched on is displayed indescending order. Fuel savingpotential is indicated.During sporadic driving conditions,the engine will activate the heatedrear window automatically to increasethe engine load. In this event, theheated rear window is indicated asone of the top consumers, withoutactivation by the driver.


Economy Trend

Displays the average consumptiondevelopment over a distance of31 miles. Filled segments display theconsumption in 3.1 mile steps andshows the effect of topography ordriving behaviour on fuelconsumption.

Economy indexThe current fuel consumption isindicated on an economic scale. Foreconomical driving, adapt drivingstyle to keep the filled segmentswithin the Eco area. The moresegments are filled, the higher thefuel consumption.

Simultaneously the averageconsumption value is indicated.

Audio menuAudio menu enables browsing formusic, selecting from favourites orchanging the audio source.See Infotainment manual.

Phone menuPhone menu enables managing andperforming of phone calls, scrollingthrough contacts or operatinghandsfree phoning.See Infotainment manual.

Navigation menuNavigation menu enables routeguidance.See Infotainment manual.

Vehicle information menu, ? orOptionsThe following list contains all possibleOptions Menu pages. Some may notbe available for your particularvehicle. Depending on the displaysome functions are symbolised.

Turn the adjuster wheel or press Qor P to select a page and follow theinstructions given in the submenus:● Units● Info pages● Speed warning● Tyre loading● Software information

UnitsPress SET/CLR or > while units isdisplayed. Select imperial or metricunits by turning adjuster wheel orpressing P. Confirm by pressingSET/CLR or 9.

Info pagesPress > while Info pages is displayed.A list of all items in the Info Menu isdisplayed. Select the functions to bedisplayed in the Info page by pressing9. Selected pages have a 9 in acheckbox. Non-viewable functionshave a blank checkbox. See InfoMenu above.


Speed warning

The speed warning function alerts thedriver when a set speed is exceeded.To set the speed warning, pressSET/CLR or > while the page isdisplayed. Turn the adjuster wheel orpress Q or P to select and adjust thevalue. Press SET/CLR or 9 to set thespeed. Once the speed is set, thisfeature can be turned off by pressingSET/CLR or 9 while viewing thispage. If the selected speed limit isexceeded, a pop-up warning isdisplayed with a chime.

Tyre LoadThe tyre pressure category accordingto the actual tyre inflation pressurecan be selected 3 239.

Software informationDisplays the open source softwareinformation.

Valet modeSome functions of the DriverInformation Centre and the Info-Display can be limited for somedrivers.Activation or deactivation of valetmode can be set in the menuSettings in the vehicle personalisationmenu.Vehicle personalisation 3 122.For more information seeInfotainment manual.

Info displayThe Info-Display is located in theinstrument panel near the instrumentcluster.

Depending on the vehicleconfiguration the vehicle has a● Graphic-Info-Display

or● 7'' Colour-Info-Display with

touch-screen functionalityor

● 8'' Colour-Info-Display withtouch-screen functionality

The vehicle has a 7'' Colour-Info-Display with touch-screenfunctionality.The vehicle has a 8'' Colour-Info-Display with touch-screenfunctionality.The Info displays can indicate:● time 3 94● outside temperature 3 94● date 3 94● Infotainment system, see

description in the Infotainmentmanual

● indication of rear view camera3 195

● indication of parking assistinstructions 3 186


● navigation, see description in theInfotainment manual

● system messages● settings for vehicle

personalisation 3 122

Graphic-Info-Display

Press X to switch on the display.Press MENU to select main menupage.Turn MENU to select a menu page.Press MENU to confirm a selection.Press BACK to exit a menu withoutchanging a setting.

7'' Colour-Info-Display

Selecting menus and settingsMenus and settings are accessed viathe display.

Press X to switch on the display.Press ; to display the homepage.Tap required menu display icon withthe finger.Tap a respective icon to confirm aselection.Tap 9 to return to the next highermenu level.Press ; to return to the homepage.

For further information, seeInfotainment manual.Vehicle personalisation 3 122.

8'' Colour-Info-Display

Selecting menus and settingsThere are three options to operate thedisplay:● via buttons below the display● by touching the touchscreen with

the finger● via speech recognition

Button operation

Press X to switch on the display.


Press ; to display the homepage.Turn MENU to select a menu displayicon or a function or to scroll asubmenu list.Press MENU to confirm a selection.Press BACK to exit a menu withoutchanging a setting.Press ; to return to the homepage.For further information, seeInfotainment manual.Touchscreen operationDisplay must be switched on bypressing X. Press ; to selecthomepage.Tap required menu display icon or afunction with the finger.Scroll a longer submenu list with thefinger up or down.Confirm a required function orselection by tapping.Tap q on the display to exit a menuwithout changing a setting.Press ; to return to the homepage.For further information, seeInfotainment manual.

Speech recognitionDescription see Infotainment manual.Vehicle personalisation 3 122.

Valet modeSome functions of the DriverInformation Centre and the Info-Display can be limited for somedrivers.Activation or deactivation of valetmode can be set in the menuSettings in the vehicle personalisationmenu.Vehicle personalisation 3 122.For more information seeInfotainment manual.

Vehicle messagesMessages are indicated in the DriverInformation Centre, in some casestogether with a warning and signalchime.

On Midlevel display press SET/CLRon the turn signal lever to confirm amessage.


On Uplevel display press 9 on thesteering wheel to confirm a message.

Vehicle and service messagesThe vehicle messages are displayedas text. Follow the instructions givenin the messages.The system displays messagesregarding the following topics:● service messages● fluid levels● anti-theft alarm system● brakes● drive systems● ride control systems

● driver assistance systems● cruise control● speed limiter● forward collision alert● collision imminent braking

system● parking assist systems● lighting, bulb replacement● LED headlights● wiper/washer system● doors, windows● side blind spot alert● traffic sign assistant● lane keep assist● load compartment, tailgate● radio remote control● electronic key system● keyless starting● seat belts● airbag systems● engine and transmission● tyre pressure● diesel particle filter

● vehicle battery status● stop-start system

Messages in theColour-Info-DisplaySome important messages mayappear additionally in theColour-Info-Display. Press themultifunction knob to confirm amessage. Some messages only pop-up for a few seconds.

Warning chimesWhen starting the engine or whilstdrivingOnly one warning chime will sound ata time.The warning chime regarding notfastened seat belts has priority overany other warning chime.● If seat belt is not fastened.● If a door or the tailgate is not fully

closed when starting off.● If a certain speed is exceeded

with parking brake applied.


● If approaching a vehicle aheadtoo closely.

● If a programmed speed or speedlimit is exceeded.

● If a warning message appears inthe Driver Information Centre.

● If the electronic key is not in thepassenger compartment.

● If the parking assist detects anobject.

● If an unintended lane changeoccurs.

● If the diesel particle filter hasreached the maximum fillinglevel.

● If safety function of the powertailgate detects obstacles in themoving area.

When the vehicle is parked and/orthe driver's door is opened● With exterior lights on.

During an Autostop● If the driver's door is opened.● If any condition for an autostart is

not fulfilled.

Battery voltageWhen the vehicle battery voltage isrunning low, a warning message willappear in the Driver InformationCentre.1. Switch off any electrical

consumers which are not requiredfor a safe drive, e.g. seat heating,heated rear window or other mainconsumers.

2. Charge the vehicle battery bydriving continuously for a while orby using a charging device.

The warning message will disappearafter the engine has been startedtwice without a voltage drop.If the vehicle battery cannot berecharged, have the cause of the faultremedied by a workshop.

Vehicle personalisationThe vehicle's behaviour can bepersonalised by changing the settingsin the Info-Display.Some of the personal settings fordifferent drivers can be memorisedindividually for each vehicle key.Memorised settings 3 23.Depending on vehicle equipment andcountry-specific regulations some ofthe functions described below maynot be available.Some functions are only displayed oractive when the engine is running.

Personal settingsGraphic-Info-DisplayPress MENU to open the respectivemenu.Select Settings, scroll through the listand select Vehicle Settings


In the corresponding submenus thefollowing settings can be changed:

Vehicle Settings● Climate and Air Quality

Auto Fan Max Speed: Modifiesthe level of the cabin airflow of theclimate control in automaticmode.Auto Heated Seats:Automatically activates the seatheating.Auto Demist: Supportswindscreen dehumidification byautomatically selecting thenecessary settings andautomatic air conditioning mode.

Auto Rear Demist: Automaticallyactivates heated rear window.

● Park Assist / Collision DetectionPark Assist: Activates ordeactivates the ultrasonicparking assist. Activation isselectable with or withoutattached trailer coupling.Side Blind Zone Alert: Activatesor deactivates side blind zonealert.

● Comfort SettingsAuto Memory Recall: Changesthe settings to the recall ofmemorised settings for powerseat adjustment.Easy Exit Driver Seat: Activatesor deactivates easy exit functionof the power seat.Chime Volume: Changes thevolume of warning chimes.Personalisation by Driver:Activates or deactivates thepersonalisation function.Rain Sense Wipers: Activates ordeactivates automatic wipingwith rain sensor.

Rear Auto Wipe in Reverse:Activates or deactivatesautomatic switching on of therear window wiper when reversegear is engaged.

● Exterior Ambient LightingExterior lighting by unlocking:Activates or deactivates the entrylighting.Duration upon exit of vehicle:Activates or deactivates andchanges the duration of exitlighting.Left or Right Hand Traffic:Changes between lighting for leftor right-hand traffic.Adaptive Forward Lighting:Changes the settings of thefunctions of the LED headlights.

● Power Door LocksStop door lock if door open:Activates or deactivates the doorlocking function while a door isopen.Auto Door Lock: Activates ordeactivates the automatic doorlocking function after switchingon ignition.


Delayed Door Lock: Activates ordeactivates the delayed doorlocking function. This featuredelays the actual locking of thedoors until all doors are closed.

● Remote Lock, Unlock, and StartRemote Unlock Feedback:Activates or deactivates thehazard warning flasher feedbackwhilst unlocking.Remote Lock Feedback:Changes what kind of feedbackis given when locking the vehicle.Remote Door Unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.Auto Relock Doors: Activates ordeactivates the automatic relockfunction after unlocking withoutopening the vehicle.Remote Window Operation:Activates or deactivates theoperation of power windows withremote control.Passive Door Unlock: Changesthe configuration to unlock only

the driver's door or the wholevehicle whilst unlocking.Passive Door Lock: Activates ordeactivates the passive lockingfunction. This feature locks thevehicle automatically afterseveral seconds if all doors havebeen closed and an electronickey has been removed from thevehicle.Remote Left in Vehicle Alarm:Activates or deactivates thewarning chime when theelectronic key remains in thevehicle.

● Restore Factory Settings:Resets all settings to the defaultsettings.

● Valet Mode:See Infotainment manual.

Personal settings7" Colour-Info-DisplayPress ;, select Settings and thenVehicle on the touch-screen.


Vehicle● Climate & Air Quality

Auto Fan Max Speed: Modifiesthe level of the cabin airflow of theclimate control in automaticmode.Auto Heated Seats:Automatically activates the seatheating.Auto Defog: Supportswindscreen dehumidification byautomatically selecting thenecessary settings andautomatic air conditioning mode.


Auto Rear Defog: Automaticallyactivates heated rear window.

● Collision / Detection SystemsPark Assist: Activates ordeactivates the ultrasonicparking assist. Activation isselectable with or withoutattached trailer coupling.Side Blind Zone Alert: Activatesor deactivates side blind zonealert.

● Comfort and ConvenienceAuto Memory Recall: Changesthe settings to the recall ofmemorised settings for powerseat adjustment.Easy Exit Driver Seat: Activatesor deactivates easy exit functionof the power seat.Chime Volume: Changes thevolume of warning chimes.Personalization By Driver:Activates or deactivates thepersonalisation function.Rain Sense Wipers: Activates ordeactivates automatic wipingwith rain sensor.

Auto Wipe in Reverse Gear:Activates or deactivatesautomatic switching on of therear window wiper when reversegear is engaged.

● LightingVehicle Locator Lights: Activatesor deactivates the entry lighting.Exit Lighting: Activates ordeactivates and changes theduration of exit lighting.Left or Right Hand Traffic:Changes between lighting for leftor right-hand traffic.Adaptive Forward Lighting:Changes the settings of thefunctions of the LED headlights.

● Power Door LocksUnlocked Door Anti Lock Out:Activates or deactivates the doorlocking function while a door isopen.Auto Door Lock: Activates ordeactivates the automatic doorlocking function after switchingon ignition.


● Remote Lock, Unlock, StartRemote Unlock Light Feedback:Activates or deactivates thehazard warning flasher feedbackwhilst unlocking.Remote Lock Feedback:Changes what kind of feedbackis given when locking the vehicle.Remote Door Unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.Relock Remotely UnlockedDoors: Activates or deactivatesthe automatic relock functionafter unlocking without openingthe vehicle.Remote Window Operation:Activates or deactivates theoperation of power windows withremote control.Passive Door Unlock: Changesthe configuration to unlock only


the driver's door or the wholevehicle whilst unlocking.Passive Door Lock: Activates ordeactivates the passive lockingfunction. This feature locks thevehicle automatically afterseveral seconds if all doors havebeen closed and an electronickey has been removed from thevehicle.Remote Left in Vehicle Alert:Activates or deactivates thewarning chime when theelectronic key remains in thevehicle.

Personal settings8" Colour-Info-DisplayPress ; then select the SETTINGSicon.


Vehicle● Climate and Air Quality

Auto Fan Speed: Modifies thelevel of the cabin airflow of theclimate control in automaticmode.Auto Heated Seats:Automatically activates the seatheating.Auto Demist: Supportswindscreen dehumidification byautomatically selecting thenecessary settings andautomatic air conditioning mode.

Auto Rear Demist: Automaticallyactivates heated rear window.

● Collision / Detection SystemsPark Assist: Activates ordeactivates the ultrasonicparking assist. Activation isselectable with or withoutattached trailer coupling.Side Blind Zone Alert: Activatesor deactivates side blind zonealert.

● Comfort and ConvenienceAuto Memory Recall: Changesthe settings to the recall ofmemorised settings for powerseat adjustment.Easy Exit Driver Seat: Activatesor deactivates easy exit functionof the power seat.Chime Volume: Changes thevolume of warning chimes.Personalisation by Driver:Activates or deactivates thepersonalisation function.Rainsense Wipers: Activates ordeactivates automatic wipingwith rain sensor.


Auto Wipe in Reverse Gear:Activates or deactivatesautomatic switching on of therear window wiper when reversegear is engaged.

● LightingVehicle Locator Lights: Activatesor deactivates the entry lighting.Exit Lighting: Activates ordeactivates and changes theduration of exit lighting.Left or Right Hand Traffic:Changes between lighting for leftor right-hand traffic.Adaptive Forward Lighting:Changes the settings of thefunctions of the LED headlights.

● Power Door LocksUnlocked Door Anti-Lockout:Activates or deactivates the doorlocking function while a door isopen.Auto Door Lock: Activates ordeactivates the automatic doorlocking function after switchingon ignition.


● Remote Lock, Unlock, StartRemote Unlock Light Feedback:Activates or deactivates thehazard warning flasher feedbackwhilst unlocking.Remote Lock Feedback:Changes what kind of feedbackis given when locking the vehicle.Remote Door Unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.Relock Remote Unlocked Doors:Activates or deactivates theautomatic relock function afterunlocking without opening thevehicle.Remote Window Operation:Activates or deactivates theoperation of power windows withremote control.Passive Door Unlock: Changesthe configuration to unlock only

the driver's door or the wholevehicle whilst unlocking.Passive Door Lock: Activates ordeactivates the passive lockingfunction. This feature locks thevehicle automatically afterseveral seconds if all doors havebeen closed and an electronickey has been removed from thevehicle.Remote Left in Vehicle Alert:Activates or deactivates thewarning chime when theelectronic key remains in thevehicle.


OnStarOnStar is a personal connectivity andservice assistant with integratedWi-Fi hotspot. The OnStar service isavailable 24 hours a day, seven daysa week.NoticeOnStar is not available for allmarkets. For further information,contact your workshop.NoticeIn order to be available andoperational, OnStar needs a validOnStar subscription, functioningvehicle electrics, mobile service andGPS satellite link.

To activate the OnStar services andset up an account, press Z and speakwith an advisor.Depending on the equipment of thevehicle, the following services areavailable:● Emergency services and support

in the case of a vehiclebreakdown

● Wi-Fi hotspot

● Smartphone application● Remote control, e.g. location of

the vehicle, activation of horn andlights, control of central lockingsystem

● Stolen vehicle assistance● Vehicle diagnostics● Destination downloadNoticeThe OnStar module of the vehicle isdeactivated after ten days without anignition cycle. Functions requiring adata connection will be availableagain after switching on the ignition.

OnStar buttons

Privacy buttonPress and hold j until a message isheard to activate or deactivate thetransmission of the vehicle location.Press j to answer a call or to end acall to an advisor.Press j to access the Wi-Fi settings.

Service buttonPress Z to establish a connection toan advisor.

SOS buttonPress [ to establish a priorityemergency connection to a speciallytrained emergency advisor.

Status LEDGreen: The system is ready.Green flashing: The system is on acall.Red: A problem arose.Off: System is in standby mode.Red / green flashing for a short periodof time: Transmission of the vehiclelocation has been deactivated.


OnStar services

General servicesIf you need any informationconcerning e.g. opening hours, pointsof interest and destinations or if youneed any support e.g. in the case of avehicle breakdown, a flat tyre andempty fuel tank, press Z to establisha connection to an advisor.

Emergency servicesIn the case of an emergency situation,press [ and talk to an advisor. Theadvisor then contacts emergency orassistance service providers anddirects them to your vehicle.In the case of an accident withactivation of airbags or belttensioners, an automatic emergencycall is established. The advisor isimmediately connected to yourvehicle to see whether help isneeded.

Wi-Fi hotspotThe Wi-Fi hotspot of the vehicleprovides internet connectivity with amaximum speed of 4G/LTE.

NoticeThe Wi-Fi hotspot functionality is notavailable for all markets.

Up to seven devices may beconnected.To connect a mobile device with theWi-Fi hotspot:1. Press j and then select Wi-Fi

settings on the Info-Display. Thesettings displayed include the Wi-Fi hotspot name (SSID),password and connection type.

2. Start a Wi-Fi network search onyour mobile device.

3. Select your vehicle hotspot(SSID) when listed.

4. When prompted, enter thepassword on your mobile device.

NoticeTo change the SSID or password,press Z and talk to an advisor or login to your account.

To switch off the Wi-Fi hotspotfunctionality, press Z to call anadvisor.

Smartphone appWith the My Vauxhall smartphoneapp, some vehicle functions can beoperated remotely.The following functions are available:● Lock or unlock vehicle.● Honk horn or flash lights.● Check fuel level, engine oil life

and tyre pressure (only with tyrepressure monitoring system).

● Send navigation destination tothe vehicle, if equipped with abuilt-in navigation system.

● Locate vehicle on a map.● Manage Wi-Fi settings.

To operate these functions, downloadthe app from Apple's App Store orGoogle Play Store.

Remote controlIf desired, use any phone to call anadvisor, who can remotely operatespecific vehicle functions. Find therespective OnStar phone number onour country-specific website.


The following functions are available:● Lock or unlock vehicle.● Provide information on the

vehicle location.● Honk horn or flash lights.

Stolen vehicle assistanceIf the vehicle is stolen, report the theftto the authorities and request OnStarstolen vehicle assistance. Use anyphone to call an advisor. Find therespective OnStar phone number onour country-specific website.OnStar can provide support inlocating and recovering the vehicle.Theft alertWhen the anti-theft alarm system istriggered, a notification is sent toOnStar. You are then informed aboutthis event by text message or email.Restart preventionBy sending remote signals, OnStarcan prevent the vehicle fromrestarting once it has been turned off.

On-demand diagnosticsAt any time e.g. if the vehicle displaysa vehicle message, press Z tocontact an advisor and ask tocomplete a real-time diagnostic checkto directly determine the issue.Depending on the results, the advisorwill provide further support.

Diagnostic reportThe vehicle automatically transmitsdiagnostic data to OnStar whichsends a monthly email report to youand your preferred workshop.NoticeThe workshop notification functioncan be disabled in your account.

The report contains the status of keyoperating systems of the vehicle likeengine, transmission, airbags, ABS,and other major systems. It alsoprovides information on possiblemaintenance items and tyre pressure(only with tyre pressure monitoringsystem).To look at the information in greaterdetail, select the link within the emailand log in to your account.

Destination downloadA desired destination can be directlydownloaded to the navigation system.Press Z to call an advisor anddescribe the destination or point ofinterest.The advisor can look up any addressor point of interest and directly sendthe destination to the built-innavigation system.

OnStar settings

OnStar PINTo have full access to all OnStarservices, a four-digit PIN is required.The PIN has to be personalised whenfirst talking to an advisor.To change the PIN, press Z to call anadvisor.

Account dataAn OnStar subscriber has an accountwhere all the data is stored. Torequest a change of the accountinformation, press Z and talk to anadvisor or log in to your account.


If the OnStar service is used onanother vehicle, press Z and requestthat the account be transferred to thenew vehicle.NoticeIn any case, if the vehicle is disposedof, sold or otherwise transferred,immediately inform OnStar aboutthe changes and terminate theOnStar service on this vehicle.

Vehicle locationThe vehicle location is transmitted toOnStar when service is requested ortriggered. A message on the Info-Display informs about thistransmission.To activate or deactivate thetransmission of the vehicle location,press and hold j until an audiomessage is heard.The deactivation is indicated by thestatus light flashing red and green fora short period of time and each timethe vehicle is started.NoticeIf the transmission of the vehiclelocation is deactivated, someservices are no longer available.

NoticeThe vehicle location always remainsaccessible to OnStar in the case ofan emergency.

Find the privacy policy in youraccount.

Software updatesOnStar may remotely carry outsoftware updates without furthernotice or consent. These updates areto enhance or maintain safety andsecurity or the operation of thevehicle.These updates may concern privacyissues. Find the privacy policy in youraccount.

132 Lighting

Lighting

Exterior lighting .......................... 132Light switch .............................. 132Automatic light control ............. 133High beam ............................... 133Headlight flash ......................... 133Headlight range adjustment .... 133Headlights when drivingabroad .................................... 134

Daytime running lights ............. 134LED headlights ........................ 134Hazard warning flashers .......... 137Turn and lane-change signals . 138Front fog lights ......................... 138Rear fog light ........................... 139Parking lights ........................... 139Reversing lights ....................... 139Misted light covers ................... 139

Interior lighting ........................... 140Instrument panel illuminationcontrol ..................................... 140

Interior lights ............................ 140Reading lights .......................... 140Sunvisor lights ......................... 141

Lighting features ........................ 141Centre console lighting ............ 141

Entry lighting ............................ 141Exit lighting .............................. 141Battery discharge protection .... 142

Exterior lightingLight switch

Turn light switch:AUTO : automatic light control

switches automaticallybetween daytime runninglight and headlight

8 : sidelights9 : headlights

When switching on the ignition,automatic light control is active.Control indicator 8 3 112.

Lighting 133

Tail lightsTail lights are illuminated togetherwith low/high beam and sidelights.

Automatic light control

When the automatic light controlfunction is switched on and theengine is running, the systemswitches between daytime runninglights and headlights automaticallydepending on the external lightingconditions and information given bythe rain sensor system.Daytime running light 3 134.

Automatic headlight activationDuring poor lighting conditionsheadlights are switched on.Additionally, headlights are switchedon if the windscreen wipers havebeen activated for several wipes.LED headlights 3 134

Tunnel detectionWhen a tunnel is entered headlightsare switched on without delay.

High beam

Push lever to switch from low to highbeam.

Pull lever to deactivate high beam.High beam assist 3 134.

Headlight flashTo activate the headlight flash, pulllever.Pulling lever deactivates high beam.LED headlights 3 134.

Headlight range adjustmentManual headlight rangeadjustment

134 Lighting

To adapt headlight range to thevehicle load to prevent dazzling: turnthumb wheel ? to required position.0 : front seats occupied1 : all seats occupied2 : all seats occupied and load

compartment laden3 : driver's seat occupied and load

compartment laden

Dynamic automatic headlightlevelling 3 134.

Headlights when drivingabroadThe asymmetrical headlight beamextends visibility at the edge of theroad at the passenger side.However, when driving in countrieswhere traffic drives on the oppositeside of the road, adjust the headlightsto prevent dazzling of oncomingtraffic.

Vehicles with halogen headlightsystemThe headlights do not have to beadjusted.

Vehicles with LED headlightHeadlights can be set for driving onthe opposite side of the road in thevehicle personalisation menu via theInfo-Display.Select the relevant setting in Settings,I Vehicle.Info-Display 3 118.Vehicle personalisation 3 122.Every time the ignition is switched on,f flashes for approx. four seconds asa reminder.To deactivate, use the sameprocedure as described above. f willnot flash when function isdeactivated.Control indicator f 3 112.

Daytime running lightsDaytime running lights increasesvisibility of the vehicle during daylight.They are switched on automaticallyduring daytime when engine isrunning.

The system switches betweendaytime running lights and headlightsautomatically, depending on thelighting conditions. Automatic lightcontrol 3 133.

LED headlightsLED headlight system contains avariety of particular LEDs in eachheadlight which enables the control ofdifferent lighting programs.Light distribution and intensity of lightare variably triggered depending onthe lighting conditions, road type anddriving situation. The vehicle adaptsthe headlights automatically to thesituation to enable optimal lightperformance for the driver.Some functions of the LED headlightscan be deactivated or activated in thevehicle personalisation menu. Selectthe relevant setting in Settings, IVehicle in the Info-Display. Vehiclepersonalisation 3 122.High beam assist can not bedeactivated.

Lighting 135

The following lighting functions areavailable with light switch in positionAUTO or 9.

Town light

Activated automatically at a speed upto approx. 34 mph and in situationswith exterior ambient light. The light iswide and symmetrical. A specialbeam pattern is designed to avoidglare for other road users.

Country light

Activated automatically at a speedabove approx. 34 mph when drivingin rural areas. The illumination of the

current lane and the side of the roadis improved. Oncoming andpreceding vehicles are not dazzled.

Curve light

Particular LEDs, based on steeringangle and speed, are additionallytriggered to improve lighting incurves. This function is activated atspeeds from 25 mph to 43 mph andreacts to steering angle.

Corner light

When turning off, depending on thesteering angle and the turn signallight, particular LEDs are triggered

which illuminate the direction oftravel. It is activated up to a speed of25 mph.

Reverse parking functionTo assist driver's orientation whenparking, both corner lights andreversing light illuminate whenheadlights are on and reverse gear isengaged. They remain illuminated fora short time after disengaging reversegear or until driving faster than4 mph in a forward gear.

High beam assistThis feature allows the high beam tofunction as main driving light at night.The camera in the windscreendetects the lights of oncoming orpreceding vehicles. Each LED onright or left side can be triggered orfaded out particulary according to thetraffic situation. This gives the bestlight distribution without glaring otherroad users. Once activated, highbeam assist remains active andswitches high beam on and offdepending on surrounding

136 Lighting

conditions. The latest setting of thehigh beam assist will remain after theignition is switched on again.

High beam assist includes a specialmotorway mode. When driving fasterthan 71 mph on motorways, the lightbeam becomes smaller to avoidglaring of oncoming traffic. Whenfollowing vehicles ahead or passing,mirror glaring for these vehicles isreduced.

ActivationIndicator lever with or without MENUbutton

Activate high beam assist by pushingthe indicator lever twice. High beam isswitched on automatically at a speedabove 31 mph. High beam is switchedoff at a speed below 22 mph, but highbeam assist remains active.

Indicator lever with f button

Activate high beam assist by pressingf once. High beam is switched onautomatically at a speed above31 mph. High beam is switched off ata speed below 22 mph, but high beamassist remains active.The green control indicator filluminates continuously when thehigh beam assist is activated, the blueone 7 illuminates when high beam ison.Control indicator f 3 112, 73 112.

Lighting 137

Pressing indicator lever onceswitches on manual high beamwithout high beam assist.High beam assist switchesautomatically to low beam when:● Driving in urban areas.● Reverse parking function is

active.● Front or rear fog lights are

switched on.If there are no restrictions detected,the system switches back to highbeam.

DeactivationIndicator lever with or without MENUbuttonIf high beam assist is active and highbeam is on, pull indicator lever onceto deactivate high beam assist.If high beam assist is active and highbeam is off, push indicator lever twiceto deactivate high beam assist.Pushing the indicator lever to activatemanual high beam will alsodeactivate high beam assist.

Indicator lever with f buttonIf high beam assist is active and highbeam is on, press f once or pullindicator lever once to deactivate highbeam assist.If high beam assist is active and highbeam is off, press f once todeactivate high beam assist.Pushing the indicator lever to activatemanual high beam will alsodeactivate high beam assist.Headlight flash in conjunction withhigh beam assistHeadlight flash by pulling indicatorlever once will not deactivate highbeam assist when high beam is off.Headlight flash by pulling indicatorlever once deactivates high beamassist when high beam is on.

Dynamic automatic headlightlevellingTo prevent oncoming traffic frombeing dazzled, headlight levelling isautomatically adjusted based oninclination information measured byfront and rear axle, acceleration ordeceleration and vehicle speed.

Headlights when driving abroad3 134.

Fault in LED headlight systemWhen the system detects a failure inthe LED headlight system, it selects apreset position to avoid dazzling ofoncoming traffic. A warning isdisplayed in the Driver InformationCentre.

Hazard warning flashersOperated by pressing ¨.

138 Lighting

The illustrations show differentversions.In the event of an accident with airbagdeployment, the hazard warningflashers are activated automatically.

Turn and lane-changesignals

lever up : right turn signallever down : left turn signal

If the lever is moved past theresistance point, the turn signal isswitched on constantly. When thesteering wheel moves back, the turnsignal is automatically deactivated.For three flashes, e.g. when changinglanes, press the lever until resistanceis felt and then release.

With a trailer connected, turn signalflashes six times and tone frequencychanges when pressing the lever untilresistance is felt and then releasing.Move the lever to the resistance pointand hold for longer indication.Switch the turn signal off manually bymoving the lever to its originalposition.

Front fog lights

Operated by pressing >.Light switch in position AUTO:switching on front fog lights will switchheadlights on automatically.

Lighting 139

Rear fog light

Operated by pressing ø.Light switch in position AUTO:switching on rear fog light will switchheadlights on automatically.Light switch in position 8: rear foglight can only be switched on withfront fog lights.The vehicle rear fog light isdeactivated when towing a trailer or aplug is connected with the socket, e.g. when a bicycle carrier is used.

Parking lights

When the vehicle is parked, theparking lights on one side can beactivated:1. Switch off ignition.2. Move turn signal lever all the way

up (right parking lights) or down(left parking lights).

Confirmed by a signal and thecorresponding turn signal controlindicator.

Reversing lightsThe reversing light comes on whenthe ignition is on and reverse gear isselected.

Misted light coversThe inside of the light housing maymist up briefly in poor, wet and coldweather conditions, in heavy rain orafter washing. The mist disappearsquickly by itself; to help switch on theheadlights.

140 Lighting

Interior lightingInstrument panelillumination control

Brightness of the following lights canbe adjusted in position AUTO whenthe light sensor detects nightconditions, or in position 8 or 9.● instrument panel illumination● Info-Display● illuminated switches and

operation elementsTurn thumb wheel A and hold untilthe desired brightness is obtained.

Interior lightsDuring entry and exit of the vehicle,the front and rear courtesy lightsautomatically switch on and then offafter a delay.NoticeIn the event of an accident withairbag deployment the courtesylights are turned on automatically.

Front courtesy light

Operate rocker switch:w : automatic switching on

and offpress u : onpress v : off

Rear courtesy lightsIlluminate in conjunction with the frontcourtesy light depending on rockerswitch position.

Reading lights

Operated by pressing s and t in thecourtesy lights.

Lighting 141

Sunvisor lightsIlluminates when the cover is opened.

Lighting featuresCentre console lightingSpotlight incorporated in the interiorlighting comes on when headlightsare switched on.

Entry lightingWelcome lightingThe following lights are switched onfor a short time by unlocking thevehicle with the radio remote control:● headlights● tail lights● number plate lights● instrument panel light● interior lights

Some functions are only operablewhen it is dark outside to facilitatelocating the vehicle.The lighting switches off immediatelywhen the ignition is switched on.Starting off 3 16.

This function can be activated ordeactivated in the vehiclepersonalisation.Select the relevant setting in Settings,I Vehicle in the Info-Display.Info-Display 3 118.Vehicle personalisation 3 122.The settings can be saved for the keybeing used 3 23.The following lights will additionallyswitch on when the driver's door isopened:● illumination of some switches● Driver Information Centre● door pocket lights

Exit lightingThe following lights switch on if thekey is removed from the ignitionswitch:● interior lights● instrument panel light● puddle lights

142 Lighting

They will switch off automatically aftera delay. This function works only inthe dark. Theatre lighting is activatedif the driver's door is opened duringthis time.

Path lightingHeadlights, tail lights and numberplate lights illuminate the surroundingarea for an adjustable time afterleaving the vehicle.

Activating

1. Switch off the ignition.2. Remove the ignition key.3. Open the driver's door.

4. Pull the turn signal lever.5. Close the driver's door.

If the driver's door is not closed, thelights switch off after two minutes.Exit lighting is switched offimmediately if the turn signal lever ispulled while the driver's door is open.This function can be activated ordeactivated in the vehiclepersonalisation.Select the relevant setting in Settings,I Vehicle in the Info-Display.Info-Display 3 118.Vehicle personalisation 3 122.The settings can be saved for the keybeing used 3 23.

Battery discharge protectionVehicle battery state of chargefunctionThe function guarantees longestvehicle battery life via a generatorwith controllable power output andoptimised power distribution.

To prevent discharge of the vehiclebattery when driving, the followingsystems are reduced automatically intwo stages and finally switched off:● auxiliary heater● heated rear window and mirrors● heated seats● fan

In the second stage, a messagewhich confirms the activation of thevehicle battery discharge protectionwill be displayed in the DriverInformation Centre.

Switching off electric lightsTo prevent discharge of the vehiclebattery when the ignition is switchedoff, some interior lights are switchedoff automatically after some time.

Climate control 143

Climate control

Climate control systems ............. 143Heating and ventilation system 143Air conditioning system ........... 144Electronic climate controlsystem .................................... 146

Auxiliary heater ........................ 151Air vents ..................................... 151

Adjustable air vents ................. 151Fixed air vents ......................... 151

Maintenance .............................. 152Air intake ................................. 152Pollen filter ............................... 152Air conditioning regularoperation ................................ 152

Service .................................... 152

Climate control systemsHeating and ventilationsystem

Controls for:● temperature● air distribution l, M and K● fan speed Z● demisting and defrosting V

Heated rear window Ü 3 42.

Temperaturered : warmblue : cold

Heating will not be fully effective untilthe engine has reached normaloperating temperature.

Air distributionl : to windscreen and front door

windowsM : to head area via adjustable air

ventsK : to foot well and windscreen

All combinations are possible.

Fan speedAdjust the air flow by switching the fanto the desired speed.

144 Climate control

Demisting and defrosting


● Set temperature control towarmest level.

● Set fan speed to highest level.● Switch on heated rear window Ü.● Open side air vents as required


Air conditioning system

In addition to the controls of theheating and ventilation system, the airconditioning system has controls for:A/C : cooling4 : air recirculation

Heated rear window Ü 3 42.Heated seats ß 3 53.Ventilated seats A 3 53.Heated steering wheel A 3 91.

Cooling A/C

Press A/C to switch on cooling.Activation is indicated by illuminationof the LED in the button. Cooling isonly functional when the engine isrunning and climate control fan isswitched on.Press A/C again to switch off cooling.The air conditioning system cools anddehumidifies (dries) as soon as theoutside temperature is slightly abovethe freezing point. Thereforecondensation may form and drip fromunder the vehicle.

Climate control 145

If no cooling or drying is required,switch off the cooling system for fuelsaving reasons.Activated cooling may inhibitAutostops. Stop-start system 3 159.

Air recirculation system 4

Press 4 to activate air recirculationmode. Activation is indicated by theLED in the button.Press 4 again to deactivate airrecirculation mode.

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up from inside.The quality of the passengercompartment air deteriorates,which may cause the vehicleoccupants to feel drowsy.

In warm and very humid ambient airconditions, the windscreen may mistup from outside when cold air isdirected towards it. If windscreenmists up from outside, activatewindscreen wiper and deactivate l.

Maximum cooling

Briefly open the windows so that hotair can disperse quickly.● Switch on cooling A/C.● Air circulation system 4 on.● Press air distribution switch M.● Set temperature control to

coldest level.● Set fan speed to highest level.● Open all vents.

146 Climate control

Demisting and defrosting thewindows V


● Set fan speed to highest level.● Set temperature control to

warmest level.● Switch on heated rear window Ü.● Open side air vents as required


NoticeIf V is pressed while the engine isrunning, an Autostop will be inhibiteduntil V is pressed again.If l is pressed with the fan switchedon and the engine running, anAutostop will be inhibited until l ispressed again or until the fan isswitched off.If V is pressed while the engine isin an Autostop, the engine will restartautomatically.If l is pressed with the fan switchedon while the engine is in anAutostop, the engine will restartautomatically.


Electronic climate controlsystemThe dual zone climate control allowsdifferent temperatures for driver sideand front passenger side.In automatic mode, temperature, fanspeed and air distribution areregulated automatically.

Controls for:● temperature on driver side● air distribution l M K● fan speed Z● temperature on front passenger

side● system on or off ON/OFF● cooling A/C● automatic mode AUTO● manual air recirculation 4● demisting and defrosting V● dual zone temperature

synchronisation SYNCHeated rear window Ü 3 42.

Climate control 147

Heated seats ß 3 53.Ventilated seats A 3 53.Heated steering wheel A 3 91.

Each change of settings is shown inthe Info-Display for a few seconds.The electronic climate control systemis only fully operational when theengine is running.

Automatic mode AUTO

Basic setting for maximum comfort:● Press AUTO, the air distribution

and fan speed are regulatedautomatically.

● Open all air vents to allowoptimised air distribution inautomatic mode.

● Press A/C to switch on optimalcooling and demisting. Activationis indicated by illumination of theLED in the button.

● Set the preselectedtemperatures for driver and frontpassenger using the left and rightrotary knob. Recommendedtemperature is 22 °C.

The fan speed regulation in automaticmode can be changed in the Settingsmenu.Vehicle personalisation 3 122.

Temperature preselection

148 Climate control

Set temperatures to the desiredvalue. The knob on the passengerside changes the temperature for thepassenger side.The knob on thedriver's side changes the temperaturefor the driver's side or for both sidesdepending on activation ofsynchronisation SYNC.The selected temperature is indicatedin the display of the knob.If the minimum temperature Lo is set,the climate control system runs atmaximum cooling, if cooling A/C isswitched on.If the maximum temperature Hi is set,the climate control system runs atmaximum heating.NoticeIf A/C is switched on, reducing theset cabin temperature can cause theengine to restart from an Autostop orinhibit an Autostop.


Dual zone temperaturesynchronisation SYNCPress SYNC to link passenger sidetemperature setting to the driver side.Activation is indicated by the LED inthe button.When passenger side settings will beadjusted, synchronisation isdeactivated and the LEDextinguishes.

Demisting and defrosting thewindows V

● Press V. Activation is indicatedby illumination of the LED in thebutton.

● Temperature and air distributionare set automatically and the fanruns at high speed.

● Switch on heated rear window Ü.● To return to previous mode:

press V, to return to automaticmode: press AUTO.

Settings of automatic rear windowheating can be changed in theSettings menu in the Info-Display.Vehicle personalisation 3 122.NoticeIf V is pressed while the engine isrunning, an Autostop will be inhibiteduntil V is pressed again.If l is pressed with the fan switchedon and the engine running, anAutostop will be inhibited until l ispressed again or until the fan isswitched off.

Climate control 149

If V is pressed while the engine isin an Autostop, the engine will restartautomatically.If l is pressed with the fan switchedon while the engine is in anAutostop, the engine will restartautomatically.


System on or off ON/OFFCooling, fan and automatic mode canbe switched off by pressing ON/OFF.When the system is deactivated, theLED in the button ON/OFF is off.Activation by pressing ON/OFF, A/Cor AUTO. Activation is indicated bythe LED in the button.

Manual settingsClimate control system settings canbe changed by activating the buttonsand rotary knobs as described below.Changing a setting will deactivate theautomatic mode.

Fan speed Z

Press left button to decrease or rightbutton to increase fan speed. The fanspeed is indicated by the number ofLEDs in the button.Pressing the left button for longer: fanand cooling are switched off.Pressing the right button for longer:the fan runs at maximum speed.To return to automatic mode: PressAUTO.

Air distribution l, M, K

Press the appropriate button for thedesired adjustment. Activation isindicated by illumination of the LED inthe button.l : to windscreen and front door

windows (air conditioning isactivated in the background tohelp preventing windows fromfogging)

M : to head area via adjustable airvents

K : to foot well and windscreen

All combinations are possible.Return to automatic air distribution:press AUTO.

150 Climate control

Cooling A/C

Press A/C to switch on cooling.Activation is indicated by illuminationof the LED in the button. Cooling isonly functional when the engine isrunning and climate control fan isswitched on.Press A/C again to switch off cooling.The air conditioning system cools anddehumidifies (dries) when outsidetemperature is above a specific level.Therefore condensation may formand drip from under the vehicle.If no cooling or drying is required,switch off the cooling system for fuelsaving reasons.

When the cooling system is switchedoff, no engine restart will berequested by the climate controlsystem during an Autostop.Exception: defrost system is activatedand outside temperature above 0 °Crequests a restart.Stop-start system 3 159.The display will indicate A/C ON whencooling is activated or A/C OFF whenthe cooling is deactivated.

Manual air recirculation 4

Press 4 to activate the airrecirculation mode. Activation isindicated by illumination of the LED inthe button.

Press 4 again to deactivaterecirculation mode.

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up from inside.The quality of the passengercompartment air deteriorates,which may cause the vehicleoccupants to feel drowsy.

In warm and very humid ambient airconditions, the windscreen may mistup from outside, when cold air isdirected towards it. If windscreenmists up from outside, activatewindscreen wiper and deactivate l.

Automatic air recirculationAn air humidity sensor switchesautomatically to external air if internalair humidity is too high.

Climate control 151

Basic settingsSome settings can be changed in theSettings menu in the Info-Display.Vehicle personalisation 3 122.

Auxiliary heaterAir heaterQuickheat is an electric auxiliary airheater which automatically warms upthe passenger compartment morequickly.

Air ventsAdjustable air ventsAt least one air vent must be openwhile cooling is on.

To open the vent, turn the adjusterwheel towards the bigger W symbol.Adjust the air amount at the ventoutlet by turning the adjuster wheel.

Direct the flow of air by tilting andswivelling the slats.To close the vent, turn the adjusterwheel towards the smaller W symbol.

9 Warning

Do not attach any objects to theslats of the air vents. Risk ofdamage and injury in case of anaccident.

Fixed air ventsAdditional air vents are locatedbeneath the windscreen and doorwindows and in the foot wells.

152 Climate control

MaintenanceAir intake

The air intake in front of thewindscreen in the enginecompartment must be kept clear toallow air intake. Remove any leaves,dirt or snow.

Pollen filterThe pollen filter cleans dust, soot,pollen and spores from the airentering the vehicle through the airintake.

Air conditioning regularoperationIn order to ensure continuouslyefficient performance, cooling mustbe operated for a few minutes once amonth, irrespective of the weatherand time of year. Operation withcooling is not possible when theoutside temperature is too low.

ServiceFor optimal cooling performance, it isrecommended to annually check theclimate control system, startingthree years after initial vehicleregistration, including:● functionality and pressure test● heating functionality● leakage check● check of drive belts● cleaning of condenser and

evaporator drainage● performance check

Driving and operating 153

Driving andoperating

Driving hints ............................... 154Control of the vehicle ............... 154Steering ................................... 154

Starting and operating ............... 154New vehicle running-in ............ 154Ignition switch positions ........... 154Power button ........................... 155Retained power off .................. 156Starting the engine .................. 157Overrun cut-off ........................ 159Stop-start system .................... 159Parking .................................... 162

Engine exhaust .......................... 164Diesel particle filter .................. 164Catalytic converter ................... 165

Automatic transmission .............. 165Transmission display ............... 165Selector lever .......................... 166Manual mode ........................... 167Electronic driving programmes 167Fault ........................................ 168Interruption of power supply .... 168

Manual transmission .................. 169

Manual transmission automa‐ted .............................................. 169

Transmission display ............... 170Selector lever .......................... 170Manual mode ........................... 171Electronic driving programmes 171Fault ........................................ 172

Brakes ........................................ 172Antilock brake system ............. 172Parking brake .......................... 173Brake assist ............................. 175Hill start assist ......................... 175

Ride control systems ................. 175Traction Control system .......... 175Electronic Stability Control ...... 176Sport mode .............................. 177

Driver assistance systems ......... 178Cruise control .......................... 178Speed limiter ........................... 180Forward collision alert ............. 181Following distance indication ... 184Active emergency braking ....... 184Parking assist .......................... 186Side blind spot alert ................. 194Rear view camera ................... 195Traffic sign assistant ................ 197Lane keep assist ..................... 201

Fuel ............................................ 203Fuel for petrol engines ............. 203

Fuel for diesel engines ............ 203Refuelling ................................ 203Fuel consumption - CO2-Emissions .............................. 204

Trailer hitch ................................ 205General information ................. 205Driving characteristics andtowing tips .............................. 206

Trailer towing ........................... 206Towing equipment ................... 207Trailer stability assist ............... 210

154 Driving and operating

Driving hintsControl of the vehicleNever coast with engine notrunningMany systems will not function in thissituation (e.g. brake servo unit, powersteering). Driving in this manner is adanger to yourself and others.All systems function during anAutostop.Stop-start system 3 159.

Idle boostIf charging of the vehicle battery isrequired due to battery condition, thepower output of the generator mustbe increased. This will be achieved byan idle boost which may be audible.A message appears in the DriverInformation Centre.

PedalsTo ensure the pedal travel isuninhibited, there must be no mats inthe area of the pedals.

Use only floor mats, which fit properlyand are fixed by the retainers on thedriver side.

SteeringIf power steering assist is lostbecause the engine stops or due to asystem malfunction, the vehicle canbe steered but may require increasedeffort.

Starting and operatingNew vehicle running-inDo not brake unnecessarily hard forthe first few journeys.During the first drive, smoke mayoccur because of wax and oilevaporating off the exhaust system.Park the vehicle in the open for awhile after the first drive and avoidinhaling the fumes.During the running-in period, fuel andengine oil consumption may behigher.Additionally, the cleaning process ofthe diesel particle filter may takeplace more often.Diesel particle filter 3 164.Autostop may be inhibited to allow forcharging of the vehicle battery.

Ignition switch positionsTurn key:


0 : ignition off: Some functionsremain active until key isremoved or driver's door isopened, provided the ignition wason previously

1 : accessory power mode: Steeringwheel lock released, someelectrical functions are operable,ignition is off

2 : ignition on power mode: Ignitionis on, diesel engine is preheating.Control indicators illuminate andmost electrical functions areoperable

3 : engine start: Release key afterstarting procedure begins

Steering wheel lockRemove key from ignition switch andturn steering wheel until it engages.

9 Danger

Never remove the key fromignition switch during driving asthis will cause steering wheel lock.

Power button

Electronic key must be inside thevehicle.

Accessory power modePress Engine Start/Stop once withoutoperating clutch or brake pedal. Theyellow LED in the button illuminates.Steering wheel lock is released andsome electrical functions areoperable, ignition is off.Ignition on power modePress and hold Engine Start/Stop forsix seconds without operating clutchor brake pedal. The green LED in thebutton illuminates, diesel engine ispreheating. Control indicatorsilluminate and most electricalfunctions are operable.Engine startOperate clutch pedal (manualtransmission) or brake pedal(automatic transmission or manualtransmission automated) and pressEngine Start/Stop once more.Release button after startingprocedure begins.Ignition offPress Engine Start/Stop briefly ineach mode or when engine is runningand vehicle is stationary. Some


functions remain active until driver'sdoor is opened, provided the ignitionwas on previously.Emergency shut off during drivingPress Engine Start/Stop for longerthan two seconds or press twicebriefly within five seconds 3 157.

Steering wheel lockThe steering wheel lock activatesautomatically when:● The vehicle is stationary.● The ignition has been switched

off.● The driver's door is opened.

To release steering wheel lock, openand close driver's door and switch onaccessory mode or start the enginedirectly.

9 Warning

If the vehicle battery is discharged,the vehicle must not be towed,tow-started or jump-started as thesteering wheel lock cannot bedisengaged.

Operation on vehicles withelectronic key system in case offailureIf either the electronic key fails or thebattery of the electronic key is weak,the Driver Information Centre maydisplay No Remote Detected orReplace Battery in Remote Key whenyou try to start the vehicle.Place the electronic key solelycentred in the transmitter area inlongitudinal direction flat with buttonsupside as shown in the illustration.

Other objects, e.g. other keys,transponder, tags, coins etc. must beremoved from the centre console.

Depress the clutch pedal (manualtransmission) or the brake pedal(automatic transmission or manualtransmission automated) and pressEngine Start/Stop.To switch off the engine, pressEngine Start/Stop again. Remove theelectronic key from the centreconsole.This option is intended foremergencies only. Replace theelectronic key battery as soon aspossible 3 21.For unlocking or locking the doors,see fault in radio remote control unitor electronic key system 3 23.

Retained power offThe following electronic systems canwork until the driver's door is openedor for ten minutes after the ignition isswitched off:● power windows● sunroof● power outlets


Starting the engineVehicles with ignition switch

Turn key to position 1 to release thesteering wheel lock.Manual transmission: operate clutchand brake pedal.Automatic transmission: operatebrake pedal and move selector leverto P or N.Manual transmission automated:operate brake pedal. If brake pedal isnot depressed, N in the transmissiondisplay could flash or a message inthe Driver Information Centre couldappear.

Do not operate accelerator pedal.Diesel engines: turn the key toposition 2 for preheating and wait untilcontrol indicator ! extinguishes.Turn key briefly to position 3 andrelease: an automatic procedureoperates the starter with a short delayuntil the engine is running, seeAutomatic Starter Control.Manual transmission: during anAutostop, the engine can be startedby depressing the clutch pedal3 159.Automatic transmission or manualtransmission automated: during anAutostop, the engine can be startedby releasing the brake pedal 3 159.

Vehicles with power button

Manual transmission: operate clutchand brake pedal.Automatic transmission: operatebrake pedal and move selector leverto P or N.Manual transmission automated:operate brake pedal. If brake pedal isnot depressed, N in the transmissiondisplay could flash or a message inthe Driver Information Centre couldappear.Do not operate accelerator pedal.


Press and release Engine Start/Stop:an automatic procedure operates thestarter with a short delay until theengine is running, see automaticstarter control.Before restarting or to switch off theengine when vehicle is stationary,press Engine Start/Stop once morebriefly.Manual transmission: during anAutostop, the engine can be startedby depressing the clutch pedal3 159.Automatic transmission or manualtransmission automated: during anAutostop, the engine can be startedby releasing the brake pedal 3 159.

Emergency shut off during drivingIf the engine needs to be switched offduring driving in case of emergency,press Engine Start/Stop for longerthan two seconds or press twicebriefly within five seconds.

9 Danger

Switching off the engine duringdriving may cause loss of powersupport for brake and steeringsystems. Assistance systems andairbag systems are disabled.Lighting and brake lights willextinguish. Therefore power downthe engine and ignition whiledriving only when required in caseof emergency.

Starting the vehicle at lowtemperaturesStarting the engine without additionalheaters is possible down to -25 °С fordiesel engines and -30 °C for petrolengines. Required is an engine oilwith the correct viscosity, the correctfuel, performed services and asufficiently charged vehicle battery.With temperatures below -30 °C theautomatic transmission requires awarming phase of approx.five minutes. The selector lever mustbe in position P.

Automatic starter controlThis function controls the enginestarting procedure. The driver doesnot need to hold the key in position 3or to hold Engine Start/Stop pressed.Once applied, the system will go onstarting automatically until the engineis running. Because of the checkingprocedure, the engine starts runningafter a short delay.Possible reasons for a non-startingengine:● Clutch pedal not operated

(manual transmission).● Brake pedal not operated or

selector lever not in P or N(automatic transmission).

● Brake pedal not operated(manual transmissionautomated).

● Timeout occurred.


Turbo engine warm-upUpon start-up, engine availabletorque may be limited for a short time,especially when the enginetemperature is cold. The limitation isto allow the lubrication system to fullyprotect the engine.

Overrun cut-offThe fuel supply is automatically cut offduring overrun, i.e. when the vehicleis driven with a gear engaged butaccelerator is released.

Stop-start systemThe stop-start system helps to savefuel and to reduce the exhaustemissions. When conditions allow, itswitches off the engine as soon as thevehicle is at a low speed or at astandstill, e.g. at a traffic light or in atraffic jam.

ActivationThe stop-start system is available assoon as the engine is started, thevehicle starts-off and the conditionsas stated below in this section arefulfilled.

Deactivation

Deactivate the stop-start systemmanually by pressing Ï OFF. Thedeactivation is indicated when theLED in the button illuminates.

AutostopVehicles with manual transmissionDepending on the engine, twoversions of an Autostop are available.See engine data to identify the engineidentifier code for your vehicle3 268.Conventional AutostopAll petrol engines and diesel enginesexcept B16DTU have only theconventional Autostop.An Autostop can be activated at astandstill or at a low speed up to3 mph.Activate a conventional Autostop asfollows:● Depress the clutch pedal.● Set the lever in neutral.● Release the clutch pedal.

The engine will be switched off whilethe ignition stays on.Early AutostopEngine B16DTU has early Autostopin addition to conventional Autostop.


An Autostop, both conventional andearly, can be activated at a standstillor at a low speed up to 9 mph.Activate an early Autostop as follows:● Depress the brake pedal.● Depress the clutch pedal.

The engine will be switched off whilethe ignition stays on.Vehicles with automatic transmissionor manual transmission automatedIf the vehicle is at a standstill withdepressed brake pedal, Autostop isactivated automatically.The engine will be switched off whilethe ignition stays on.The stop-start system will be disabledon inclines of 15% or more.

Indication

An Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.After restart, the idle speed isindicated.During an Autostop, the heating andbrake performance will bemaintained.

Conditions for an AutostopThe stop-start system checks if eachof the following conditions is fulfilled.● The stop-start system is not

manually deactivated.● The bonnet is fully closed.

● The driver's door is closed or thedriver's seat belt is fastened.

● The vehicle battery is sufficientlycharged and in good condition.

● The engine is warmed up.● The engine coolant temperature

is not too high.● The engine exhaust temperature

is not too high, e.g. after drivingwith high engine load.

● The ambient temperature isabove -5 °C.

● The climate control systemallows an Autostop.

● The brake vacuum is sufficient.● The self-cleaning function of the

diesel particle filter is not active.● The vehicle was driven at least at

walking speed since the lastAutostop.

Otherwise an Autostop will beinhibited.Certain settings of the climate controlsystem may inhibit an Autostop. SeeClimate control chapter for moredetails 3 144.


Immediately after motorway drivingan Autostop may be inhibited.New vehicle running-in 3 154.

Vehicle battery discharge protectionTo ensure reliable engine restarts,several vehicle battery dischargeprotection features are implementedas part of the stop-start system.

Power saving measuresDuring an Autostop, several electricalfeatures such as auxiliary electricheater or rear window heating aredisabled or switched to a powersaving mode. The fan speed of theclimate control system is reduced tosave power.

Restart of the engine by the driverVehicles with manual transmissionDepending on the engine, twoversions of a restart are available.See engine data to identify the engineidentifier code for your vehicle3 268.

A restart for all engines exceptB16DTU is possible at a standstill orat a low speed up to 4 mph and up to9 mph for engine B16DTU.Conventional restartAll engines have conventional restart.Depress the clutch pedal withoutpressing the brake pedal to restart theengine.On engines with late restart onlypossible without depressed brakepedal.Late restartAll petrol engines and the dieselengines B16DTU and B16DTR havelate restart in addition to conventionalrestart.● Depress the brake pedal.● Depress the clutch pedal.● Select first gear.● Release the brake pedal to

restart the engine.Vehicles with automatic transmissionor manual transmission automated:Release the brake pedal or moveselector lever out of D into N or P torestart the engine.

Restart of the engine by the stop-start systemOn vehicles with manual transmissionwhich are in a conventional Autostop,the selector lever must be in neutralto enable an automatic restart.On vehicles with manual transmissionwhich are in an early Autostop, anautomatic restart is possible in everyselector lever position.On vehicles with automatictransmission or manual transmissionautomated, the selector lever must bein D to enable an automatic restart.If one of the following conditionsoccurs during an Autostop, theengine will be restarted automaticallyby the stop-start system:● The stop-start system is

manually deactivated.● The bonnet is opened.● The driver's seat belt is

unfastened and the driver's dooris opened.

● The engine temperature is toolow.


● The charging level of the vehiclebattery is below a defined level.

● The brake vacuum is notsufficient.

● The vehicle is driven at least atwalking speed.

● The climate control systemrequests an engine start.

● The air conditioning is manuallyswitched on.

If the bonnet is not fully closed, awarning message is displayed in theDriver Information Centre.If an electrical accessory, e.g. aportable CD player, is connected tothe power outlet, a brief power dropduring the restart might be noticeable.

Parking

9 Warning

● Do not park the vehicle on aneasily ignitable surface. Thehigh temperature of theexhaust system could ignite thesurface.

● Always apply the parkingbrake. Activate the manualparking brake without pressingthe release button. Apply asfirmly as possible on a downhillslope or uphill slope. Depressbrake pedal at the same time toreduce operating force.For vehicles with electricparking brake, pull switch m fora minimum of one second untilcontrol indicator m illuminatesconstantly and electric parkingbrake is applied 3 109.

● Switch off the engine.● If the vehicle is on a level

surface or uphill slope, engagefirst gear or set the selectorlever to position P beforeremoving the ignition key orswitching off ignition onvehicles with power button. Onan uphill slope, turn the frontwheels away from the kerb.If the vehicle is on a downhillslope, engage reverse gear orset the selector lever to position

P before removing the ignitionkey or switching off ignition onvehicles with power button.Turn the front wheels towardsthe kerb.

● Close the windows and thesunroof.

● Remove the ignition key fromthe ignition switch or switch offignition on vehicles with powerbutton. Turn the steering wheeluntil the steering wheel lock isfelt to engage.For vehicles with automatictransmission, the key can onlybe removed when the selectorlever is in position P.For vehicles with manualtransmission automated, thekey can only be removed fromthe ignition switch when theparking brake is applied.


● Lock the vehicle.● Activate the anti-theft alarm

system.● The engine cooling fans may run

after the engine has beenswitched off 3 213.

Caution

After running at high enginespeeds or with high engine loads,operate the engine briefly at a lowload or run in neutral forapprox. 30 seconds beforeswitching off, in order to protectthe turbocharger.

NoticeIn the event of an accident withairbag deployment, the engine isswitched off automatically if thevehicle comes to a standstill within acertain time.

Emergency operation underextreme cold temperatures

9 Warning

This emergency operation mayonly be carried out in case ofextremely cold temperatures and ifthe vehicle is parked on a levelsurface.

In countries with extreme coldtemperatures it may be necessary topark the vehicle without appliedparking brake.This is an emergency operation toavoid freezing of the parking brake.

Vehicles equipped with manualtransmission automated, electricparking brake and power buttonOn vehicles with manual transmissionautomated the ignition can only beswitched off if the parking brake isapplied. Therefore the following itemsmust be carried out to release theelectric parking brake:

1. Apply electric parking brake andswitch off ignition.

2. Switch on ignition by pressing andholding Engine Start/Stop for sixseconds without operating brakepedal.

3. Press brake pedal and releaseelectric parking brake.

4. Switch off ignition.


Engine exhaust

9 Danger

Engine exhaust gases containpoisonous carbon monoxide,which is colourless and odourlessand could be fatal if inhaled.If exhaust gases enter the interiorof the vehicle, open the windows.Have the cause of the faultrectified by a workshop.Avoid driving with an open loadcompartment, otherwise exhaustgases could enter the vehicle.

Diesel particle filterAutomatic cleaning processThe diesel particle filter system filtersharmful soot particles out of theexhaust gases. The system includesa self-cleaning function that runsautomatically during driving withoutany notification. The filter is cleanedby periodically burning off the sootparticles at high temperature. Thisprocess takes place automaticallyunder set driving conditions and maytake up to 25 minutes. Typically itneeds between seven and twelveminutes. Autostop is not availableand fuel consumption may be higherduring this period. The emission ofsmells and smoke during this processis normal.

System requires manual cleaningprocessUnder certain driving conditions, e.g.short distances, the system cannotclean itself automatically.If cleaning of the filter is required andif previous driving conditions did notenable automatic cleaning, it will be

indicated by % and a warningmessage in the Driver InformationCentre.% with a warning messageilluminates when diesel particle filteris full. Start cleaning process as soonas possible.% with a warning message flasheswhen diesel particle filter has reachedthe maximum filling level. Startcleaning process immediately toavoid damage to the engine.

Activate manual cleaning processTo activate cleaning process,continue driving, keep engine speedabove 2000 revolutions per minute.Shift down if necessary. Dieselparticle filter cleaning is then started.Cleaning takes place quickest at highengine speeds and loads.The control indicator % extinguishesas soon as the self-cleaningoperation is complete. Keep ondriving until self-cleaning operation iscomplete.


Caution

If the cleaning process isinterrupted, there is a risk ofprovoking severe engine damage.

Cleaning process not possibleIf cleaning is not possible for anyreasons, Z illuminates and a warningmessage appears in the DriverInformation Centre. Engine powermay be reduced. Seek the assistanceof a workshop immediately.

Catalytic converterThe catalytic converter reduces theamount of harmful substances in theexhaust gases.

Caution

Fuel grades other than those listedon pages 3 203, 3 268 coulddamage the catalytic converter orelectronic components.Unburnt petrol will overheat anddamage the catalytic converter.Therefore avoid excessive use ofthe starter, running the fuel tankdry and starting the engine bypushing or towing.

In the event of misfiring, unevenengine running, a reduction in engineperformance or other unusualproblems, have the cause of the faultrectified by a workshop as soon aspossible. In an emergency, drivingcan be continued for a short period,keeping vehicle speed and enginespeed low.

Automatic transmissionThe automatic transmission permitsautomatic gearshifting (automaticmode) or manual gearshifting(manual mode).Manual shifting is possible in manualmode by tapping the selector lever to+ or - 3 167.

Transmission display

The mode or selected gear is shownin the transmission display.


In automatic mode, the drivingprogramme is indicated by D in theDriver Information Centre.In manual mode, M and the numberof the selected gear is indicated.R indicates reverse gear.N indicates neutral position.P indicates park position.

Selector lever

P : park position, wheels are locked,engage only when the vehicle isstationary and the parking brakeis applied

R : reverse gear, engage only whenthe vehicle is stationary

N : neutralD : automatic modeM : manual mode< : upshift in manual mode] : downshift in manual mode

The selector lever is locked in P andcan only be moved when the ignitionis on, the release button on theselector lever is pushed and the brakepedal is applied.

Without brake pedal applied, controlindicator j illuminates.If the selector lever is not in P whenthe ignition is switched off, controlindicator j flashes.To engage P or R, press the releasebutton.The engine can only be started withthe lever in position P or N. Whenposition N is selected, press the brakepedal or apply the parking brakebefore starting.Do not accelerate while engaging agear. Never depress the acceleratorpedal and brake pedal at the sametime.When a gear is engaged, the vehicleslowly begins to creep when thebrake is released.

Engine brakingTo utilise the engine braking effect,select a lower gear in good time whendriving downhill, see manual mode.


Rocking the vehicleRocking the vehicle is onlypermissible if the vehicle is stuck insand, mud or snow. Move the selectorlever between D and R in a repeatpattern. Do not race the engine andavoid sudden acceleration.

ParkingApply the parking brake and engageP.The ignition key can only be removedwhen the selector lever is in positionP.

Manual mode

Move selector lever out of position Dtowards the left in position M.Tap selector lever upwards + to shiftto a higher gear.Tap the selector lever downwards - toshift to a lower gear.If a higher gear is selected whenvehicle speed is too low, or a lowergear when vehicle speed is too high,the shift is not executed. This cancause a message in the DriverInformation Centre.In manual mode, no automaticshifting to a higher gear takes placeat high engine revolutions.

Gear shift indicationThe symbol R or S with a numberbeside it is indicated whengearshifting is recommended for fuelsaving reasons.Shift indication appears only inmanual mode.

Electronic drivingprogrammes● Following a cold start, the

operating temperatureprogramme increases enginespeed to quickly bring thecatalytic converter to the requiredtemperature.

● Special programmesautomatically adapt the shiftingpoints when driving up inclines ordown hills.

● In snowy or icy conditions or onother slippery surfaces, theelectronic transmission controlenables the driver to selectmanually first, second or thirdgear for starting off.

KickdownIf the accelerator pedal is presseddown completely in automatic mode,the transmission shifts to a lower geardepending on engine speed.


FaultIn the event of a fault a message isdisplayed in the Driver InformationCentre. Vehicle messages 3 120.Electronic transmission controlenables only fourth gear. Thetransmission no longer shiftsautomatically.Have the cause of the fault remediedby a workshop.

Interruption of power supplyIn the event of an interruption ofpower supply, the selector levercannot be moved out of the Pposition. The ignition key cannot beremoved from the ignition switch.If the vehicle battery is discharged,start the vehicle using jump leads3 253.If the vehicle battery is not the causeof the fault, release the selector lever.1. Apply the parking brake.

2. Release the selector lever trimfrom the centre console. Pokewith a finger into the leathersocket below the selector leverand push the trim upwards.Rotate trim to the left.

3. Insert a small stick (e.g. a pen orscrew driver) into the openingnear the selector lever. Pushdown the the stick vertically andmove the selector lever out of P. Ifthis position is engaged again, theselector lever will be locked again.Have the cause of the powersupply interruption remedied by aworkshop.

4. Mount the selector lever trim ontothe centre console and refit.


Manual transmission

To engage reverse, depress theclutch pedal and then press therelease button on the selector leverand engage the gear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Do not slip the clutch unnecessarily.When operating, depress the clutchpedal completely. Do not use thepedal as a foot rest.

Caution

It is not advisable to drive with thehand resting on the selector lever.

Gear shift indication 3 110.Stop-start system 3 159.

Manual transmissionautomatedThe automated manual transmissionpermits manual gearshifting (manualmode) or automatic gearshifting(automatic mode), both withautomatic clutch control.Manual shifting is possible by tappingthe selector lever in manual mode.NoticeWhen unlocking or opening avehicle door, a sound may beaudible caused by the hydraulicsystem.


Transmission display

In automatic mode, the drivingprogramme is indicated by D in theDriver Information Centre.In manual mode, M and the numberof the selected gear is indicated.R indicates reverse gear.N indicates neutral.

Selector lever

Always move the selector lever in theappropriate direction as far as it willgo. Upon release, it automaticallyreturns to the centre position.N : neutral positionD/M : switch between automatic (D)

and manual (M) shift mode.The transmission displayshows either D or M with theselected gear

< : upshifting in manual mode] : downshifting in manual modeR : reverse gear. Engage only

when vehicle is stationary

If selector lever is moved from R to theleft, D is directly engaged.If selector lever is moved from D to +or -, manual mode M is selected andthe transmission shifts.

Starting offDepress the brake pedal and movethe selector lever to D/M or R. If D isselected, transmission is in automaticmode and first gear is engaged. If Ris selected, reverse gear is engaged.The vehicle starts to move when thebrake pedal is released.To start-off without depressing thebrake pedal, accelerate immediatelyafter engaging a gear as long as D orR flashes.If neither the accelerator nor thebrake pedal are depressed, no gearis engaged and D or R flashes for abrief time in the display.

Stopping the vehicleIn D, first gear is engaged and theclutch is released when the vehicle isstopped. In R, reverse gear remainsengaged.


Engine braking

Automatic modeWhen driving downhill, the manualtransmission automated does notshift into higher gears until a fairlyhigh engine speed has been reached.It shifts down in good time whenbraking.

Manual modeTo utilise the engine braking effect,select a lower gear in good time whendriving downhill. Changing intomanual mode is only possible whilethe engine is running or during anAutostop.

Rocking the vehicleRocking the vehicle is onlypermissible if the vehicle is stuck insand, mud or snow. Move the selectorlever between R and D in a repeatpattern. Do not race the engine andavoid sudden acceleration.

ParkingThe most recently engaged gear (seetransmission display) remainsengaged when switching off ignition.With N, no gear is engaged.Therefore always apply the parkingbrake when switching off ignition. Ifparking brake is not applied, P flashesin the transmission display and thekey cannot be removed from theignition switch. P stops flashing in thetransmission display as soon as theparking brake is slightly applied.When the ignition is switched off, thetransmission no longer responds tomovement of the selector lever.

Manual modeIf a higher gear is selected when theengine speed is too low, or a lowergear when the speed is too high, theshift is not executed. This preventsthe engine from running at too low ortoo high an engine speed. A warningmessage is displayed in the DriverInformation Centre. Vehiclemessages 3 120.

If engine speed is too low, thetransmission automatically shifts to alower gear.When + or - is selected in automaticmode, the transmission switches tomanual mode and shifts accordingly.

Gear shift indicationThe symbol R or S with a numberbeside is indicated when gearshiftingis recommended for fuel savingreasons.Shift indication appears only inmanual mode.

Electronic drivingprogrammes● Following a cold start, the

operating temperatureprogramme increases enginespeed to quickly bring thecatalytic converter to the requiredtemperature.

● The adaptive programme tailorsgearshifting to the drivingconditions, e.g. greater load orgradients.


KickdownIf the accelerator pedal is presseddown completely in automatic mode,the transmission shifts to a lower geardepending on engine speed.

FaultTo prevent damage to the manualtransmission automated, the clutch isengaged automatically at high clutchtemperatures.In the event of a fault, a warningmessage is displayed in the DriverInformation Centre. Vehiclemessages 3 120.Continued driving is restricted or notpossible, depending on the fault.Have the cause of the fault remediedby a workshop.

BrakesThe brake system comprises twoindependent brake circuits.If a brake circuit fails, the vehicle canstill be braked using the other brakecircuit. However, braking effect isachieved only when the brake pedalis depressed firmly. Considerablymore force is needed for this. Thebraking distance is extended. Seekthe assistance of a workshop beforecontinuing the journey.When the engine is not running, thesupport of the brake servo unitdisappears once the brake pedal hasbeen depressed once or twice.Braking effect is not reduced, butbraking requires significantly greaterforce. It is especially important to bearthis in mind when being towed.Control indicator R 3 109.

Antilock brake systemAntilock brake system (ABS)prevents the wheels from locking.

ABS starts to regulate brake pressureas soon as a wheel shows a tendencyto lock. The vehicle remainssteerable, even during hard braking.ABS control is made apparentthrough a pulse in the brake pedaland the noise of the regulationprocess.For optimum braking, keep the brakepedal fully depressed throughout thebraking process, despite the fact thatthe pedal is pulsating. Do not reducethe pressure on the pedal.After starting off, the system performsa self-test which may be audible.

Control indicator u 3 110.

Adaptive brake lightDuring full braking, all three brakelights flash for the duration of ABScontrol.


Fault

9 Warning

If there is a fault in the ABS, thewheels may be liable to lock dueto braking that is heavier thannormal. The advantages of ABSare no longer available. Duringhard braking, the vehicle can nolonger be steered and mayswerve.

Have the cause of the fault remediedby a workshop.

Parking brake

9 Warning

Before leaving the vehicle, checkparking brake status. Controlindicator m must illuminateconstantly.

Manual parking brake

9 Warning

Always apply parking brake firmlywithout operating the releasebutton, and apply as firmly aspossible on a downhill or uphillslope.To release the parking brake, pullthe lever up slightly, press therelease button and fully lower thelever.To reduce the operating forces ofthe parking brake, depress thefoot brake at the same time.

Control indicator R 3 109.

Electric parking brake

Applying when vehicle is stationary

9 Warning

Pull switch m for a minimum ofone second until control indicatorm illuminates constantly andelectric parking brake is applied


3 109. The electric parking brakeoperates automatically withadequate force.Before leaving the vehicle, checkthe electric parking brake status.Control indicator m 3 109.

The electric parking brake can alwaysbe activated, even if the ignition is off.Do not operate electric parking brakesystem too often without enginerunning as this will discharge thevehicle battery.

ReleasingSwitch on ignition. Keep foot brakepedal depressed and then pushswitch m.

Drive away functionVehicles with manual transmission:Depressing the clutch pedal and thenslightly releasing the clutch pedal andslightly depressing the acceleratorpedal releases the electric parkingbrake automatically. This is notpossible when switch m is pulled atthe same time.

Vehicles with automatic transmissionor manual transmission automated:Engaging D and then depressing theaccelerator pedal releases theelectric parking brake automatically.This is not possible when switch m ispulled at the same time.

Dynamic braking when vehicle ismovingWhen the vehicle is moving and theswitch m is kept pulled, the electricparking brake system will deceleratethe vehicle, but will not applystatically.As soon as the switch m is released,dynamic braking will be stopped.

Automatic applyingIf the vehicle is equipped withautomatic transmission and adaptivecruise control is active, electricparking brake is applied automaticallywhen vehicle is stopped by thesystem for more than two minutes.Parking brake releases automaticallyafter moving off.

Functionality checkWhen the vehicle is not moving, theelectric parking brake might beapplied automatically. This is done tocheck the system.

FaultFailure mode of electric parking brakeis indicated by a control indicator jand by a vehicle message which isdisplayed in the Driver InformationCentre. Vehicle messages 3 120.Apply electric parking brake: pull andhold the switch m for more thanfive seconds. If control indicator milluminates, electric parking brake isapplied.Release electric parking brake: pushand hold the switch m for more thantwo seconds. If control indicator mextinguishes, electric parking brake isreleased.Control indicator m flashes: electricparking brake is not fully applied orreleased. When continuouslyflashing, release electric parkingbrake and retry applying.


Brake assistIf brake pedal is depressed quicklyand forcefully, maximum brake forceis automatically applied.Operation of brake assist mightbecome apparent by a pulse in thebrake pedal and a greater resistancewhen depressing the brake pedal.Maintain steady pressure on thebrake pedal as long as full braking isrequired. Maximum brake force isautomatically reduced when brakepedal is released.

Hill start assistThe system helps prevent unintendedmovement when driving away oninclines.When releasing the brake pedal afterstopping on an incline, brakes remainon for further two seconds. Thebrakes release automatically as soonas the vehicle begins to accelerate.

Ride control systemsTraction Control systemThe Traction Control system (TC) is acomponent of the Electronic StabilityControl (ESC).TC improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip, bypreventing the drive wheels fromspinning.As soon as the drive wheels starts tospin, engine output is reduced andthe wheel spinning the most is brakedindividually. This considerablyimproves the driving stability of thevehicle on slippery road surfaces.

TC is operational after each enginestart as soon as the control indicatorb extinguishes.When TC operates b flashes.

9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Control indicator b 3 110.

Deactivation

TC can be switched off when spinningof drive wheels is required: press bbriefly.


Control indicator k illuminates.A status message appears in theDriver Information Centre when TC isdeactivated.When TC is deactivated, ESCremains active but with higher controlthreshold.TC is reactivated by pressing bagain. A status message pops up inthe Driver Information Centre whenTC is reactivated.TC is also reactivated the next timethe ignition is switched on.

FaultIf there is a fault in the system thecontrol indicator b illuminatescontinuously and a message appearsin the Driver Information Centre. Thesystem is not operational.


Electronic Stability ControlElectronic Stability Control (ESC)improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip.As soon as the vehicle starts toswerve (understeer/oversteer),engine output is reduced and thewheels are braked individually.ESC operates in combination with theTraction Control system (TC). Itprevents the drive wheels fromspinning.Torque distribution is a specialfeature that allocates the torque to thedrive wheels before the ESCintervenes. When cornering, thewheels on the inner curve are brakedindividually. Additionally, enginetorque will be delivered to the drivewheel on the outer curve. Thisreduces the tendency ofundersteering and improves tractionwhen cornering fast.

ESC is operational after each enginestart as soon as the control indicatorb extinguishes.When ESC operates b flashes.

9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Control indicator b 3 110.


Deactivation

ESC and TC can be deactivated:● hold b pressed for a minimum of

five seconds: ESC and TC areboth deactivated. k and nilluminate and status messagesappear in the Driver InformationCentre.

● To deactivate only Tractioncontrol system press button bbriefly: TC is inactive but ESCremains active, k illuminates. Astatus message appears in theDriver Information Centre whenTC is deactivated.

ESC is reactivated by pressing theb button again. If the TC system waspreviously disabled, both TC andESC are reactivated. k and nextinguishes when TC and ESC arereactivated.ESC is also reactivated the next timethe ignition is switched on.

FaultIf there is a fault in the system thecontrol indicator b illuminatescontinuously and a message appearsin the Driver Information Centre. Thesystem is not operational.


Sport modeSport mode adapts the settings ofsome vehicle systems to a sportierdriving style.● The engine reacts more quickly

to the accelerator pedal.● Steering reacts more direct to

provide better contact with theroad surface.

● Shift points of automatictransmission occur later.

Activation


Press SPORT when engine isrunning.LED in the button lights up when sportmode is active and a status messageappears in the Driver InformationCentre.

DeactivationBriefly press SPORT. Sport mode isdeactivated the next time the ignitionis switched on.

Driver assistancesystems

9 Warning

Driver assistance systems aredeveloped to support the driverand not to replace the driver'sattention.The driver accepts fullresponsibility when driving thevehicle.When using driver assistancesystems, always take careregarding the current trafficsituation.

Cruise controlThe cruise control can store andmaintain speeds of approx. 20 mph tomaximum vehicle speed. Deviationsfrom the stored speeds may occurwhen driving uphill or downhill.For safety reasons, the cruise controlcannot be activated until the footbrake has been operated once.Activating in first gear is not possible.

Do not use the cruise control if it is notadvisable to maintain a constantspeed.

Illustrations show different versions.


On vehicles with automatictransmission or manual transmissionautomated cruise control can beactivated in automatic mode andmanual mode.Control indicator m 3 112.

Switching on

Press m; control indicator m ininstrument cluster illuminates white.

Activation

Accelerate to the desired speed andturn thumb wheel to SET/-, thecurrent speed is stored andmaintained. Control indicator m in

instrument cluster illuminates green.Set speed is indicated on the display.Accelerator pedal can be released.Vehicle speed can be increased bydepressing the accelerator pedal.When the accelerator pedal isreleased, the previously stored speedis resumed.Cruise control remains activatedwhile gearshifting.

Increase speedWith cruise control active, hold thumbwheel turned to RES/+ or briefly turnto RES/+ repeatedly: speedincreases continuously or in smallincrements.Alternatively accelerate to the desiredspeed and store by turning to SET/-.

Reduce speedWith cruise control active, hold thumbwheel turned to SET/- or briefly turn toSET/- repeatedly: speed decreasescontinuously or in small increments.

DeactivationPress y; control indicator m ininstrument cluster illuminates white.Cruise control is deactivated. Laststored speed remains in memory forlater speed resume.


Automatic deactivation:● Vehicle speed is below approx.

20 mph.● Vehicle speed drops more than

15 mph below the set speed.● The brake pedal is depressed.● The clutch pedal is depressed for

a few seconds.● The selector lever is in N.● Engine speed is in a very low

range.● The Traction Control system or

Electronic Stability Control isoperating.

● Parking brake is applied.● Simultaneous pressing RES/+

and brake pedal deactivatescruise control and will deletestored speed.

Resume stored speedTurn thumb wheel to RES/+ at aspeed above 20 mph. The storedspeed will be obtained.

Switching offPress m, control indicator m ininstrument cluster extinguishes. Thestored speed is deleted.Pressing L to activate the speedlimiter or switching off the ignition alsoswitches off cruise control anddeletes the stored speed.

Speed limiterThe speed limiter prevents thevehicle exceeding a preset maximumspeed.The maximum speed can be set atspeeds above 15 mph up to125 mph.The driver can only accelerate up tothe preset speed. Deviations from thelimited speed may occur when drivingdownhill.The preset speed limit is displayed inthe Driver Information Centre whenthe system is active.

Activation

Illustrations show different versions.


Press L. If cruise control has beenactivated before, it is switched offwhen speed limiter is activated andcontrol indicator m extinguishes.

Set speed limitAccelerate to the desired speed andbriefly turn thumb wheel to SET/-: thecurrent speed is stored as maximumspeed. Speed limit is displayed in theDriver Information Centre.

Change speed limitWith speed limiter active, hold orbriefly turn thumb wheel to RES/+ toincrease or SET/- to decrease thedesired maximum speed.

Exceeding the speed limitWhen exceeding the limited speedwithout driver input, the speed willflash in the Driver Information Centreand a chime sounds during thisperiod.In the event of an emergency, it ispossible to exceed the speed limit bydepressing the accelerator pedalfirmly nearly to the final point. In thiscase no chime appears.Release the accelerator pedal andthe speed limiter function isreactivated once a speed lower thanthe limit speed is obtained.

DeactivationPress y: speed limiter is deactivatedand the vehicle can be driven withoutspeed limit.The limited speed will be stored andis indicated in brackets in the DriverInformation Centre. Additionally, acorresponding message appears.

Resume limit speedTurn thumb wheel to RES/+. Thestored speed limit will be obtained.

Switching offPress L, the speed limit indicationextinguishes in the Driver InformationCentre. The stored speed is deleted.By pressing m to activate cruisecontrol, speed limiter is alsodeactivated and the stored speed isdeleted.By switching off the ignition, speedlimiter is also deactivated, but thespeed limit will be stored for nextspeed limiter activation.

Forward collision alertThe forward collision alert can help toavoid or reduce the harm caused byfront-end crashes.Forward collision alert uses the frontcamera system in the windscreen todetect a vehicle directly ahead, inyour path, within a distance of approx.60 metres.


A vehicle ahead is indicated bycontrol indicator A.If a vehicle directly ahead isapproached too quickly, a warningchime and alert in the DriverInformation Centre is provided.Additionally the driver gets notified bya flashing red LED stripe which isprojected on the windscreen in thedriver's field of view.A precondition is that forward collisionalert is not deactivated by pressingV.

ActivationForward collision alert operatesautomatically above 5 mph, if it is notdeactivated by pressing V, seebelow.

Selecting the alert sensitivityThe alert sensitivity can be set tonear, medium or far.

Press V, the current setting is shownon the Driver Information Centre.Press V repeatedly to change thealert sensitivity. The selected settingis also displayed in the DriverInformation Centre.

Alerting the driverThe vehicle ahead control indicatorA illuminates green in the instrumentcluster when the system has detecteda vehicle in the driving path.The control indicator A changes toyellow when the distance to apreceding moving vehicle gets toosmall or when approaching anothervehicle too rapidly.


Caution

The colour lighting of this controlindicator does not correspond tolocal traffic laws on followingdistance. The driver bears fullresponsibility for maintaining safefollowing distance according toapplicable traffic rules, weatherand road conditions etc. at alltimes.

When the time to a potential collisionwith a vehicle in front gets too smalland a collision is imminent, thecollision alert symbol pops-up in theDriver Information Centre and thedriver gets notified by a flashing redLED stripe which is projected on thewindscreen in the driver's field ofview.

Simultaneously a warning chimesounds. Depress the brake pedal andsteer the vehicle, if it is required by thesituation.

DeactivationThe system can be deactivated.Press V repeatedly until ForwardCollision Alert Off appears in theDriver Information Centre.If the forward collision alert wasdeactivated, alert sensitivity is set to"medium" when ignition is switchedon next time.The settings "near", "medium" or "far"will be stored when the ignition isswitched off.

General information

9 Warning

Forward collision alert is just awarning system and does notapply the brakes. Whenapproaching a vehicle ahead toorapidly, it may not provide youenough time to avoid a collision.The driver accepts fullresponsibility for the appropriatefollowing distance based on traffic,weather and visibility conditions.The complete attention of thedriver is always required whiledriving. The driver must always beready to take action and apply thebrakes.

System limitationsThe system is designed to warn onvehicles only, but may react also toother objects.


In the following cases, forwardcollision alert may not detect a vehicleahead or sensor performance islimited:● on winding roads● when weather limits visibility,

such as fog, rain, or snow● when the sensor is blocked by

snow, ice, slush, mud, dirt,windscreen damage or affectedby foreign items, e.g. stickers

Following distanceindicationThe following distance indicationdisplays the distance to a precedingmoving vehicle. The front camera inthe windscreen is used to detect thedistance of a vehicle directly ahead inthe vehicle's path. It is active atspeeds above 25 mph.When a preceding vehicle is detectedahead, the distance is indicated inseconds, displayed on a page in theDriver Information Centre.

On Midlevel display, choose InfoMenu ? via MENU on the turnsignal lever and turn the adjusterwheel to choose following distanceindication page,3 113

On Uplevel display, select Info menuvia steering wheel buttons and presso to select following distanceindication 3 113.The minimum indicated distance is0.5 seconds.If there is no vehicle ahead or thevehicle ahead is out of range, twodashes will be displayed: -.- sec.

Active emergency brakingActive emergency braking can help toreduce the damage and injury fromcrashes with vehicles and obstaclesdirectly ahead, when a collision canno longer be avoided either bymanual braking or by steering. Beforethe active emergency brakingapplies, the driver is warned by theforward collision alert 3 181.The feature uses various inputs (e.g.camera sensor, brake pressure,vehicle speed) to calculate theprobability of a frontal collision.Active emergency braking operatesabove walking speed up to 53 mph. Aprecondition is that the system is notdeactivated by toggling the gapswitch V to Off setting, 3 181.The system includes:● brake preparation system● emergency automatic braking● forward looking brake assist


9 Warning

This system is not intended toreplace the driver responsibility fordriving the vehicle and lookingahead. Its function is limited tosupplemental use only. The drivermust continue to apply the brakepedal as the driving situationdictates.

Brake preparation systemWhen approaching a vehicle aheadso quickly that a collision is likely, thebrake preparation system slightlypressurises the brakes. This reducesthe response time, when a manual orautomatic braking is requested.The brake system is prepared so thatbraking can occur more rapidly.The system operates up to a speed of50 mph.

Emergency automatic brakingAfter the brake preparation and justbefore the imminent collision, thisfunction automatically applies limitedbraking to reduce the impact speed ofthe collision or prohibit a crash.The system operates up to a speed of37 mph.Below a speed of 25 mph the systemcan apply full braking.

Forward looking brake assistIn addition to the brake preparationsystem and emergency automaticbraking, the forward looking brakeassist function makes the brake assistmore sensitive. Therefore,depressing the brake pedal lessstrongly results in immediate hardbraking. This function helps the driverbrake quicker and harder before theimminent collision.The system operates up to a speed of53 mph.

9 Warning

Active emergency braking is notdesigned to apply hardautonomous braking or toautomatically avoid a collision. It isdesigned to reduce the vehiclespeed before a collision. It may notreact for pedestrians or animals.After a sudden lane change, thesystem needs a certain time todetect the next preceding vehicle.The complete attention of thedriver is always required whiledriving. The driver shall always beready to take action and apply thebrakes and steer to avoidcollisions. The system is designedto work with all occupants wearingtheir seat belts.

System limitationsThe active emergency braking haslimited or no function during rain,snow or heavy dirt, as the camerasensor can be covered by a waterfilm, dust, ice or snow. In case ofsensor blockage, clean the sensorcover.


In some cases, the active emergencybraking system may provide anautomatic braking in situations thatseem to be unnecessary, for instancein parking garages, due to traffic signsin a curve or due to vehicles inanother lane. This is normaloperation, the vehicle does not needservice. Firmly apply the acceleratorpedal to override the automaticbraking.

Deactivation

Active emergency braking can bedeactivated by repeatedly pressingthe gap switch V to Off setting,

3 181. If deactivated a message isdisplayed in the Driver InformationCentre.

FaultIn the event of a system servicerequirement, a message is displayedin the Driver Information Centre.If the system does not work as itshould do, vehicle messages aredisplayed in the Driver InformationCentre.Vehicle messages 3 120.

Parking assistRear parking assist

9 Warning

It is the driver who bears fullresponsibility for the parkingmanoeuvre.Always check the surroundingarea while reversing and using therear parking assist system.

The rear parking assist makesparking easier by measuring thedistance between the vehicle andrear obstacles. It informs and warnsthe driver by giving acoustic signalsand display indication.

The system has four ultrasonicparking sensors in the rear bumper.

ActivationAfter ignition is switched on, the rearparking assist is activated.An illuminated LED in the parkingassist button r indicates that thesystem is ready to operate.


IndicationThe system warns the driver withacoustic signals against potentiallyhazardous obstacles behind thevehicle in a distance range up to50 cm while a forward gear isengaged, respectively up to1.5 metres while reverse gear isengaged.Depending on which side of thevehicle is closer to an obstacle, youwill hear acoustic warning signals inthe vehicle on the respective side.The interval between the soundsbecomes shorter as the vehicle getscloser to that obstacle. When thedistance is less than approx. 30 cm,the sound is continuous.Additionally, the distance to rearobstacles is displayed by changingdistance lines in the DriverInformation Centre 3 113.The distance indication can beinhibited by vehicle messages with ahigher priority. After dismissing themessage distance indication appearsagain.

Deactivation

Press parking assist button r todeactivate, the LED in the buttonextinguishes.

FaultIn the event of a fault or if the systemdoes not work temporarily, e.g.because of high external noise levelor other interference factors, the LEDin the button flashes forthree seconds and then extinguishes.A message is indicated in the DriverInformation Centre.

Front-rear parking assist

9 Warning

The driver bears full responsibilityfor the parking manoeuvre.Always check the surroundingarea when driving backwards orforwards while using parkingassist system.

The front-rear parking assistmeasures the distance between thevehicle and obstacles in front andbehind the vehicle. It informs andwarns the driver by giving acousticsignals and display indication.It uses two different acoustic warningsignals for the front and rearmonitoring areas, each with adifferent tone frequency.


The system has four ultrasonicparking sensors each in the rear andfront bumper.

ActivationThe system is activated automaticallyat a speed up to 7 mph.

An illuminated LED in the parkingassist button r indicates that thesystem is ready to operate.If r is switched off within an ignitioncycle, the front parking assist isdeactivated. If vehicle speed hasexceeded 15 mph beforehand,parking assist will be reactivatedwhen speed drops below 7 mph.When the system is deactivated, theLED in the button extinguishes andPark Assist Off pops-up in the DriverInformation Centre.

IndicationThe system warns the driver withacoustic signals against potentiallyhazardous obstacles in front of thevehicle in a distance range up to 80cm and against potentially hazardousobstacles behind the vehicle in adistance range up to 50 cm while aforward gear is engaged, respectivelyup to 1.5 m while reverse gear isengaged.Depending on which side of thevehicle is closer to an obstacle, youwill hear acoustic warning signals inthe vehicle on the respective side.The interval between the soundsbecomes shorter as the vehicle getscloser to that obstacle. When thedistance is less than approx. 30 cm,the sound is continuous.Additionally, the distance to rear andfront obstacles is displayed bychanging distance lines in the DriverInformation Centre 3 113 or,depending on the version, on the Info-Display 3 118.


The distance indication can beinhibited by vehicle messages with ahigher priority. After dismissing themessage distance indication appearsagain.

DeactivationThe system is deactivatedautomatically when vehicle speedexceeds 7 mph.Manual deactivation is also possibleby pressing the parking assist buttonr.

When the system is deactivatedmanually, the LED in the buttonextinguishes and Park Assist Offpops-up in the Driver InformationCentre.After a manual deactivation, the front-rear parking assist is activated againif r is pressed or if reverse gear isengaged.The complete system can bemanually deactivated in the vehiclepersonalisation menu in theInfo-Display. It remains deactivatedduring the ignition cycle or untilactivation in personalisation menuagain. Vehicle personalisation 3 122.When using the trailer hitch changethe configuration settings in thevehicle personalisation menu in theInfo-Display. Vehicle personalisation3 122.

FaultIn the event of a fault or if the systemdoes not work temporarily, e.g.because of high external noise levelor other interference factors, amessage pops-up in the DriverInformation Centre.

Vehicle messages 3 120.

Advanced parking assist

9 Warning

The driver bears full responsibilityfor accepting the parking slotsuggested by the system and theparking manoeuvre.Always check the surroundingarea in all directions when usingthe advanced parking assist.

The advanced parking assistmeasures a suitable parking slotwhile passing, calculates thetrajectory and automatically steersthe vehicle into a parallel orperpendicular parking slot.Instructions are given in the DriverInformation Centre 3 113 or,depending on the version, on the Info-Display 3 118, supported by acousticsignals.The driver must control acceleration,braking and gear shifting, whilesteering is done automatically.


Advanced parking assist is alwayscombined with front-rear parkingassist. Both systems use the samesensors in the front and rear bumper.The system has six ultrasonic parkingsensors each in both the rear andfront bumper.

Activation of advanced parking assistAdvanced parking assist can only beactivated when driving forwards.

When searching for a parking slot, thesystem is ready to operate with ashort press of (.The system recognises andmemorises ten metres for parallelparking slots or six metres forperpendicular parking slots in theparking assist mode.The system can only be activated ata speed up to 18 mph and the systemsearches for a parking slot at a speedup to 18 mph.The maximum allowed paralleldistance between the vehicle and arow of parked cars is 1.8 metres forparallel parking and 2.5 metres forperpendicular parking.

FunctionalityParking slot searching mode,indication in the Driver InformationCentre

Select parallel or perpendicularparking slot in Driver InformationCentre by long press on (.The system is configured to detectparking slots by default on thepassenger side. To detect parkingslots on the driver side, switch on turnsignal indicator on the driver side.


When a slot is detected, a visualfeedback in the Driver InformationCentre and an acoustic signal isgiven.

Indication in the Colour-Info-Display

Select parallel or perpendicularparking slot by tapping the respectiveicon on the display.Select parking side by tapping therespective icon on the display.

When a slot is detected, a visualfeedback on the Colour-Info-Displayand an acoustic signal is given.If the driver does not stop the vehicleafter a parking slot is proposed, thesystem starts to search for anothersuitable parking slot.Park guiding modeThe parking slot suggestion of thesystem is accepted when the vehicleis stopped by the driver within tenmetres for parallel parking slots orsix metres for perpendicular parkingslots after the Stop message is given.The system calculates the optimalpath into the parking slot.


A brief vibration in the steering wheelafter engaging reverse gear indicatesthat the steering is controlled by thesystem. Then the vehicle is steeredinto the slot automatically by givingthe driver detailed instructions forbraking, accelerating and gearshifting. The driver must keep handsaway from the steering wheel.Always pay attention to the sound ofthe front-rear parking assist.Continuous sound indicates that thedistance to an obstacle is less thanapprox. 30 cm.If, for any reason, the driver must takeover control of the steering, hold thesteering wheel only at the outer edge.Automatic steering is cancelled in thisevent.Display indicationThe instructions on the display show:● General hints and warning

messages.● A hint when driving faster than

18 mph during parking slotsearching mode.

● The demand to stop the vehicle,when a parking slot is detected.

● The direction of driving during theparking manoeuvre.

● The demand to shift into reverseor first gear.

● The demand to accelerate orbrake.

● For some of the instructions aprogress bar is shown in theDriver Information Centre.

● The successful completion of theparking manoeuvre indicated bya pop-up symbol and a chime.

● The cancelling of a parkingmanoeuvre.

Display prioritiesAdvanced parking assist indication inthe Driver Information Centre can beinhibited by vehicle messages with ahigher priority. After approving themessage by pressing SET/CLR onthe turn signal lever or 9 on thesteering wheel, advanced parkingassist instructions appear again andthe parking manoeuvre can becontinued.

DeactivationThe system is deactivated by:● a short press of (● parking manoeuvre successfully

ended● driving faster than 18 mph during

parking slot search● driving faster than 5 mph during

parking guidance● driver interference on steering

wheel detected● exceeding number of maximum

gear changes: eight cycles whenparallel parking or five cycleswhen perpendicular parking

● switching off the ignitionDeactivation by the driver or by thesystem during manoeuvring will beindicated by Parking Deactivated onthe display. Additionally, an acousticsignal sounds.


FaultA message appears when:● There is a fault in the system.● The driver did not successfully

complete the parkingmanoeuvre.

● The system is not operational.● Any of the deactivation reasons

described above apply.If an object is detected during parkinginstructions, Stop is indicated on thedisplay. Removing the object willresume the parking manoeuvre. If theobject is not removed, the system willbe deactivated. A long press of ( willactivate the system and search for anew parking slot.

Basic notes on parking assistsystems

9 Warning

Under certain circumstances,various reflective surfaces onobjects or clothing as well as

external noise sources may causethe system to fail to detectobstacles.Special attention must be paid tolow obstacles which can damagethe lower part of the bumper.

Caution

Performance of the system can bereduced when sensors arecovered, e.g. by ice or snow.Performance of the parking assistsystem can be reduced due toheavy loading.Special conditions apply if thereare taller vehicles in the vicinity(e.g. off-road vehicles, mini vans,vans). Object identification andcorrect distance indication in theupper part of these vehiclescannot be guaranteed.Objects with a very small reflectioncross-section, e.g. objects ofnarrow size or soft materials, maynot be detected by the system.

Parking assist systems do notdetect objects outside thedetection range.

NoticeIt is possible that the sensor detectsa non-existing object caused byecho disturbance from externalacoustic noise or mechanicalmisalignments (sporadic falsewarnings may occur).Make sure that the front numberplate is properly mounted (not bentand no gaps to the bumper on the leftor right side) and the sensors arefirmly in place.Advanced parking assist systemmay not respond to changes in theavailable parking space afterinitiating a parking manoeuvre. Thesystem may recognize an entry, agateway, a courtyard or even acrossing as a parking slot. Afterselecting reverse gear the system


will start a parking manoeuvre. Takecare regarding the availability of thesuggested parking slot.Surface irregularities, e.g. onconstruction zones, are not detectedby the system. The driver acceptsresponsibility.NoticeAfter production, the systemrequires a calibration. For optimalparking guidance, a driving distanceof at least 6 miles, including anumber of bends, is required.

Side blind spot alertThe Side blind spot alert systemdetects and reports objects on eitherside of the vehicle, within a specified"blind spot" zone. The system alertsvisually in each exterior mirror, whendetecting objects that may not bevisible in the interior and exteriormirrors.Side blind spot alert uses some of theadvanced parking assist sensorswhich are located in the front and rearbumper on both sides of the vehicle.

9 Warning

Side blind spot alert does notreplace driver vision.The system does not detect:

● vehicles outside the side blindzones which may be rapidlyapproaching

● pedestrians, cyclists or animalsBefore changing a lane, alwayscheck all mirrors, look over theshoulder and use the turn signal.

When the system detects a vehicle inthe side blind zone while drivingforwards, either while passing avehicle or being passed, a yellowwarning symbol B will illuminate inthe relevant exterior mirror. If thedriver then activates the turn signal,the warning symbol B starts flashingyellow as a warning not to changelanes.

NoticeIf the overtaking vehicle is at least6 mph faster than the vehicle beingovertaken, the warning symbol B inthe relevant exterior mirror may notilluminate.

Side blind spot alert is active fromspeeds of 6 mph up to 87 mph.Driving faster than 87 mphdeactivates the system, indicated bylow lighting warning symbols B inboth exterior mirrors. Reducing thespeed again will extinguish thewarning symbols. If a vehicle is thendetected in the blind zone, thewarning symbols B will illuminate asnormal on the relevant side.


When the vehicle is started, bothexterior mirror displays will brieflycome on to indicate that the system isoperating.The system can be activated ordeactivated in the Info-Display,vehicle personalisation 3 122.Deactivation is indicated by amessage in the Driver InformationCentre.

Detection zonesThe detection zones start at the rearbumper and extend approx.three metres rearwards and to thesides. The height of the zone isapprox. between half a metre andtwo metres off the ground.Side blind spot alert is designed toignore stationary objects, e.g.guardrails, posts, curbs, walls andbeams. Parked vehicles or oncomingvehicles are not detected.

FaultOccasional missed alerts can occurunder normal circumstances and willincrease in wet conditions.

Side blind spot alert does not operatewhen the left or right corners of therear bumper are covered with mud,dirt, snow, ice, slush, or in heavyrainstorms. Cleaning instructions3 257.In the event of a fault in the system orif the system does not work due totemporary conditions, the symbols inthe mirrors will be permanentlyilluminated and a message isdisplayed in the Driver InformationCentre. Seek the assistance of aworkshop.

Rear view cameraThe rear view camera assists thedriver when reversing by displaying aview of the area behind the vehicle.The view of the camera is displayedin the Colour-Info-Display.

9 Warning

The rear view camera does notreplace driver vision. Note thatobjects that are outside thecamera's field of view and the

advanced parking assist sensors,e.g. below the bumper orunderneath the vehicle, are notdisplayed.Do not reverse the vehicle by onlylooking at the Info-Display andcheck the surrounding areabehind and around the vehiclebefore reversing.

ActivationRear view camera is automaticallyactivated when reverse gear isengaged.

Functionality


On 5-door hatchback the camera ismounted between the number platelights.On Sports Tourer the camera ismounted under the tailgate moulding.

The area displayed by the camera islimited. The distance of the image thatappears on the display differs fromthe actual distance.

Guiding linesDynamic guiding lines are horizontallines at one metre intervals projectedonto the picture to define the distanceto displayed objects.

Trajectory lane of the vehicle isshown in accordance with thesteering angle.

Warning symbolsWarning symbols are indicated astriangles 9 on the picture, which showobstacles detected by the rearsensors of the advanced parkingassist.Additionally 9 appears on the top lineof the Info-Display with the warning tocheck the vehicle surrounding.

Display settingsBrightness and contrast can be set bytapping the touch screen displaywhen rear view camera is active.

DeactivationThe camera is switched off when acertain forward speed is exceeded orif reverse gear is not engaged forapprox. 15 seconds. Rear viewcamera can be manually deactivatedin the vehicle personalisation menu inthe Colour-Info-Display. Select therelevant setting in Settings, I Vehicle.

Deactivation of guiding lines andwarning symbols


7'' Colour-Info-Display: Activation ordeactivation of the visual guiding linesand the warning symbols can bechanged via touch buttons in thelower zone of the display.8'' Colour-Info-Display: Activation ordeactivation of the visual guiding linesand the warning symbols can bechanged in the Settings menu in theInfo-Display. Select the relevantsetting in Settings, I Vehicle.Info-Display 3 118.Vehicle personalisation 3 122.

FaultFault messages are displayed with a9 on the top line of the Info-Display.The rear view camera may notoperate properly when:● The surrounding is dark.● The sun or the beam of

headlights is shining directly intothe camera lens.

● Ice, snow, mud, or anything elsecovers the camera lens. Cleanthe lens, rinse it with water, andwipe it with a soft cloth.

● The vehicle is towing a trailer.● The vehicle had a rear end

accident.● There are extreme temperature

changes.

Traffic sign assistantFunctionalityTraffic sign assistant detectsdesignated traffic signs via a frontcamera and displays them in theDriver Information Centre.If the vehicle is equipped with anembedded navigation system, trafficsigns fom data maps may be includedadditionally.

Traffic signs, which will be detected,are:Limit and no passing signs● speed limit● no passing● end of speed limit● end of no passing

Road signsBeginning and end of:● city regions (country specific)● motorways● A-roads● play streets


Add on signs● additional hints to traffic signs● restriction of trailer towing● tractor constraints● wet warning● ice warning● time constraints● distance constraints● direction arrows

Speed limit signs and no passingsigns are displayed in the DriverInformation Centre until the nextspeed limit sign or end of speed limitis detected or up to a defined signtimeout.

Indication of multiple signs on thedisplay is possible.

An exclamation mark in a frameindicates that there is an additionalsign detected which cannot be clearlyidentified by the system.The system operates without loss ofperformance up to a speed of125 mph depending on the lightingconditions. At night the system isactive up to a speed of 100 mph.

Display indicationInformation about the currently validtraffic signs is available on thedesignated traffic sign assistant pagein the Driver Information Centre.Additionally, the currently valid speedlimit is displayed permanently in thelower line of the Driver InformationCentre. In case a speed limit with addon sign is available, a + symbol isdisplayed in this area.

On Midlevel display, choose InfoMenu ? via MENU and selecttraffic sign assistant page with theadjuster wheel on the turn signal lever3 113.


On Uplevel display, choose InfoMenu via right steering wheel buttonsand press P or Q to select trafficsign assistant page 3 113.When another page on the DriverInformation Centre menu wasselected and then traffic signassistant page is chosen again, thelast recognised traffic sign will bedisplayed.

Alert functionThe alert function can be activated ordeactivated in the setting menu of thetraffic sign assistant page.

Once activated and when the trafficsign detection page is currently notdisplayed, newly detected speed limitand no passing signs are displayedas popup alerts in the DriverInformation Centre.On Midlevel Display, when traffic signassistant page is displayed, pressSET/CLR on the turn signal lever.

Select Alerts ON or Alerts OFF byturning the adjuster wheel and pressSET/CLR.On Uplevel Display, when traffic signassistant page is displayed, press qon the steering wheel controls.

Activate alerts by setting J,deactivate alerts by setting I viabutton 9.Pop-up alert is displayed for approx.eight seconds in the DriverInformation Centre.

System resetThe content of the traffic sign displaycan be cleared in the setting menu ofthe traffic sign assistant page byselecting Reset and confirm bypressing SET/CLR on the turn signallever or 9 on the steering wheelcontrols.


Alternatively, SET/CLR or 9 can bepressed for three seconds to clear thecontent of the page.Upon successful reset, a chime willsound and the following “DefaultSign” is indicated until the next trafficsign is detected or provided by mapdata of the navigation system.

In some cases, traffic sign assistant iscleared up automatically by thesystem.

Clearing of traffic signsThere are different scenarios thatlead to clearing the currentlydisplayed traffic signs. After clearing,the “Default Sign” or a sign fromnavigation map data is displayed inthe Driver Information Centre.

Reasons for signs being cleared:● A predefined distance was driven

or time has elapsed (differs foreach sign type)

● Vehicle drives through a turn● If no navigation map data is

available and speed drops below32 mph (city entry detection)

● If navigation map data isavailable and a city entry/exit wasdetected due to map data change

Traffic sign detection inconjunction with navigationsystemIf the vehicle is equipped with anavigation system, the currentlydisplayed sign can either originatefrom optical sign detection or from themap data.If the currently displayed signoriginates from map data and the mapinformation changes, a new sign willbe displayed. This may lead todetection of a new sign although nosign on the road may have beenpassed.

FaultTraffic sign assistant may not operatecorrectly if:● The area of the windscreen,

where the front camera islocated, is not clean or affectedby foreign items, e.g. stickers.

● Traffic signs are completely orpartially covered or difficult todiscern.

● There are adverse environmentalconditions, e.g. heavy rain, snow,direct sunlight or shadows.

● Traffic signs are incorrectlymounted or damaged.

● Traffic signs do not comply withthe Vienna Convention on trafficsigns (Wiener Übereinkommenüber Straßenverkehrszeichen).

Caution

The system is intended to help thedriver within a defined speedrange to discern certain traffic


signs. Do not ignore traffic signswhich are not displayed by thesystem.The system does not discern anyother than the conventional trafficsigns that might give or end aspeed limit.Do not let this special featuretempt you into taking risks whendriving.Always adapt speed to the roadconditions.The driver assistance systems donot relieve the driver from fullresponsibility for vehicleoperation.

Lane keep assistLane keep assist helps to avoidcrashes due to unintentional lanedepartures. The front cameraobserves the lane markings betweenwhich the vehicle is driving. If thevehicle approaches a lane marking,the steering wheel is gently turned toposition the vehicle back into the lane.Turn steering wheel in samedirection, if system steers not

sufficient. Turn steering wheel gentlyinto opposite direction, if lane changeis intended.When crossing a lane markingsignificantly, lane keep assist starts avisual and acoustic warning.Unintended lane departure isassumed● without using turn signal● using the turn signal in the

opposite direction of the lanedeparture

● without braking● without acceleration● without active steering.NoticeThe system is switched off duringdetection of ambiguous lanemarkings, e.g. in construction areas.NoticeThe system may be switched off if itdetects lanes which are too narrow,too wide or too curved.

Activation

The lane keep assist is activated bypressing a. The LED in the buttonilluminates to indicate that the systemis switched on.

When the control indicator a in theinstrument cluster illuminates green,the system is ready to assist.


The system is operational at vehiclespeeds between 37 mph and112 mph and if lane markings areavailable.The system gently turns the steeringwheel and the control indicator achanges to yellow, if the vehicleapproaches a detected lane markingwithout using the turn signal in thatdirection.The system alerts by flashing atogether with three chimes, from therespective direction, if the lane isdeparted significantly.The system is only operable when alane marking is detected.If the system only detects lanemarkings on one side of the road, itwill only assist for this side.Lane keep assist detects hands-freedriving. In this case a message in theDriver Information Centre pops-upand a chime sounds as long as lanekeep assist detects hands-freedriving.

DeactivationThe system is deactivated bypressing a; the LED in the buttonextinguishes.

FaultThe system performance may beaffected by:● Windscreen not clean or affected

by foreign items, e.g. stickers● Close vehicles ahead● Banked roads● Winding or hilly roads● Road edges● Roads with poor lane markings● Sudden lighting changes● Adverse environmental

conditions e.g. heavy rain orsnow

● Vehicle modifications, e.g. tyres.Switch off the system if the system isdisturbed by tar marks, shadows,road cracks, temporary orconstruction lane markings, or otherroad imperfections.

9 Warning

Always keep your attention on theroad and maintain proper vehicleposition within the lane, otherwisevehicle damage, injury or deathcould occur.Lane keep assist does notcontinuously steer the vehicle.The system may not keep thevehicle in the lane or give an alert,even if a lane marking is detected.The steering of the lane keepassist may not be sufficient toavoid a lane departure.The system may not detect hands-off driving due to externalinfluences (road condition andsurface, weather etc). The driverhas full responsibility to control thevehicle and is always required tokeep the hands on the steeringwheel while driving.Using the system while towing atrailer or on slippery roads couldcause loss of control of the vehicleand a crash. Switch the system off.


FuelFuel for petrol enginesOnly use unleaded fuel that complieswith European standard EN 228 orE DIN 51626-1 or equivalent.The engine is capable of running withfuel that contains up to 10% ethanol(e.g. named E10).Use fuel with the recommendedoctane rating. The engine specificrequirements are given in the enginedata overview 3 268. A countryspecific label at the fuel filler flap cansupersede the requirement.

Caution

Do not use fuel or fuel additivesthat contain metallic compoundssuch as manganese-basedadditives. This may cause enginedamage.

Caution

Use of fuel that does not comply toEN 228 or E DIN 51626-1 orequivalent can lead to deposits orengine damage.

Caution

Use of fuel with too low an octanerating could lead to uncontrolledcombustion and engine damage.

Fuel for diesel enginesOnly use diesel fuel that complieswith EN 590.In countries outside the EuropeanUnion use Euro-Diesel fuel with asulphur concentration below 50 ppm.

Caution

Use of fuel that does not comply toEN 590 or similar can lead toengine powerloss, increased wearor engine damage.

Do not use marine diesel oils, heatingoils, Aquazole and similar diesel-water emulsions. Diesel fuels mustnot be diluted with fuels for petrolengines.

Refuelling

9 Danger

Before refuelling, switch offignition and any external heaterswith combustion chambers.Follow the operating and safetyinstructions of the filling stationwhen refuelling.


9 Danger

Fuel is flammable and explosive.No smoking. No naked flames orsparks.If you can smell fuel in yourvehicle, have the cause of thisremedied immediately by aworkshop.

Caution

In case of misfuelling, do notswitch on ignition.

Fuel filler flap is located at right rearside of the vehicle.

The fuel filler flap can only be openedif the vehicle is unlocked. Release thefuel filler flap by pushing the flap.To open, turn the cap slowlyanticlockwise.

The fuel filler cap can be retained inthe bracket on the fuel filler flap.To refuel, fully insert the pump nozzleand switch it on.After automatic cut-off, it can betopped up by operating the pumpnozzle maximally two more times.

Caution

Wipe off any overflowing fuelimmediately.

To close, turn the fuel filler capclockwise until it clicks.Close the flap and engage.

Fuel filler capOnly use genuine fuel filler caps.Diesel-engined vehicles have specialfuel filler caps.

Fuel consumption - CO2-Emissions The fuel consumption (combined) ofthe model Vauxhall Astra is within arange of 46 to 85 mpg.


The CO2 emission (combined) iswithin a range of 142 to 88 g/km.For the values specific for yourvehicle, refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.

General informationThe official fuel consumption andspecific CO2 emission figures quotedrelate to the EU base model withstandard equipment.Fuel consumption data and CO2emission data are determinedaccording to regulation R (EC)No. 715/2007 (in the latest applicableversion), taking into consideration thevehicle weight in running order, asspecified by the regulation.The figures are provided only for thepurpose of comparison betweendifferent vehicle variants and mustnot be taken as a guarantee for theactual fuel consumption of aparticular vehicle. Additionalequipment may result in slightlyhigher results than the stated

consumption and CO2 figures.Furthermore, fuel consumption isdependent on personal driving styleas well as road and traffic conditions.

Trailer hitchGeneral informationOnly use towing equipment that hasbeen approved for your vehicle.Entrust retrofitting of towingequipment to a workshop. It may benecessary to make changes thataffect the cooling system, heatshields or other equipment.The bulb outage detection function fortrailer brake light cannot detect apartial bulb outage, e.g. in case of fourtimes five watt bulbs, the function onlydetects lamp outage when only asingle five Watt lamp remains or noneremain.Fitting of towing equipment couldcover the opening of the towing eye.If this is the case use the coupling ballbar for towing. Always keep thecoupling ball bar in the vehicle whennot in use.


Driving characteristics andtowing tipsBefore attaching a trailer, lubricatethe coupling ball. However, do not doso if a stabiliser, which acts on thecoupling ball, is being used to reducesnaking movements.During trailer towing do not exceed aspeed of 50 mph. A maximum speedof 60 mph is only appropriate if anoscillation damper is used and thepermissible gross trailer weight doesnot exceed the vehicle's curb weight.For trailers with low driving stabilityand caravan trailers, the use of anoscillation damper is stronglyrecommended.If the trailer starts snaking, drive moreslowly, do not attempt to correct thesteering and brake sharply ifnecessary.When driving downhill, drive in thesame gear as if driving uphill anddrive at a similar speed.Adjust tyre pressure to the valuespecified for full load 3 276.

Trailer towingTrailer loads

9 Warning

Vehicles with engine B14XFT andautomatic transmission:Use of towing equipment ispermissible for attachingcompatible bicycle carriers only.Do not use towing equipment fortrailer towing.

The permissible trailer loads arevehicle and engine-dependentmaximum values which must not beexceeded. The actual trailer load isthe difference between the actualgross weight of the trailer and theactual coupling socket load with thetrailer coupled.The permissible trailer loads arespecified in the vehicle documents. Ingeneral, they are valid for gradientsup to max. 12%.The permitted trailer load applies upto the specified incline and up to analtitude of 1000 metres above sea

level. Since engine power decreasesas altitude increases due to the airbecoming thinner, therefore reducingclimbing ability, the permissible grosstrain weight also decreases by 10%for every 1000 metres of additionalaltitude. The gross train weight doesnot have to be reduced when drivingon roads with slight inclines (less than8%, e.g. motorways).The permissible gross train weightmust not be exceeded. This weight isspecified on the identification plate3 263.

Vertical coupling loadThe vertical coupling load is the loadexerted by the trailer on the couplingball. It can be varied by changing theweight distribution when loading thetrailer.The maximum permissible verticalcoupling load (75 kg) is specified onthe towing equipment identificationplate and in the vehicle documents.Always aim for the maximum load,especially in the case of heavytrailers. The vertical coupling loadshould never fall below 25 kg.


Rear axle loadWhen the trailer is coupled and thetowing vehicle fully loaded, thepermissible rear axle load (seeidentification plate or vehicledocuments) may be exceeded by40 kg. If the permissible rear axle loadis exceeded, a maximum speed of60 mph applies.

Towing equipment

Caution

When operating without a trailer,remove the coupling ball bar.

Stowage of coupling ball barThe bag with the coupling ball bar isstowed on the rear floor cover in theload compartment.Place the strap through the rear rightlashing eye, wrap around twice andtighten the strap to secure the bag.

Illustration shows 5-door hatchback.

Illustration shows Sports Tourer.

Fitting the coupling ball bar

On Sports Tourer remove cover fromrear bumper by pushing.


Disengage and fold down theconnecting socket. Remove thesealing plug from the opening for thecoupling ball bar and stow it.

Checking the tensioning of thecoupling ball bar

● Red marking on rotary knob mustpoint towards green marking oncoupling ball bar.

● The gap between the rotary knoband the coupling ball bar must beapprox. 6 mm.

● The key must be in position c.

Otherwise, the coupling ball bar mustbe tensioned before being inserted:● Unlock coupling ball bar by

turning key to position c.

● Pull out rotary knob and turnclockwise as far as it will go.

Inserting the coupling ball bar

Insert the tensioned coupling ball barin the opening and push firmlyupwards until it audibly engages.The rotary handle snaps back into itsoriginal position resting against thecoupling ball bar without a gap.

9 Warning

Do not touch rotary handle duringinsertion.

Lock the coupling ball bar by turningthe key to position e. Remove the keyand close the protective flap.


Eye for break-away stopping cable

Attach breakaway stopping cable toeye.

Check that the coupling ball bar iscorrectly installed● Green marking on rotary knob

must point towards greenmarking on coupling ball bar.

● There must be no gap betweenthe rotary handle and thecoupling ball bar.

● The coupling ball bar must befirmly engaged in the opening.

● The coupling ball bar must belocked and the key removed.

9 Warning

Towing a trailer is permitted onlywhen a coupling ball bar is fittedcorrectly. If the coupling ball bardoes not engage correctly, seekthe assistance of a workshop.

Dismounting the coupling ball bar

Open the protective flap and turn thekey to position c to unlock thecoupling ball bar.Pull out rotary handle and turnclockwise as far as it will go. Pull outcoupling ball bar downwards.Insert sealing plug in opening.

Fold away connecting socket.

On Sports Tourer insert cover intorear bumper as shown in theillustration.


Stow the coupling ball bar in the bagand secure by fixing the strap throughthe rear right lashing eye. Wraparound twice and tighten the strap tosecure the bag.

Trailer stability assistIf the system detects snakingmovements, engine power is reducedand the vehicle/trailer combination isselectively braked until the snakingceases. While system is working keepsteering wheel as still as possible.Trailer stability assist is a function ofthe Electronic Stability Control 3 176.

Vehicle care 211

Vehicle care

General Information ................... 211Accessories and vehiclemodifications .......................... 211

Vehicle storage ........................ 212End-of-life vehicle recovery ..... 212

Vehicle checks ........................... 213Performing work ...................... 213Bonnet ..................................... 213Engine oil ................................. 214Engine coolant ......................... 215Washer fluid ............................ 216Brakes ..................................... 216Brake fluid ............................... 216Vehicle battery ......................... 217Diesel fuel system bleeding ..... 218Wiper blade replacement ........ 219

Bulb replacement ....................... 219Halogen headlights .................. 219Fog lights ................................. 221Tail lights ................................. 222Side turn signal lights .............. 228Number plate light ................... 229Interior lights ............................ 229Instrument panel illumination ... 229

Electrical system ........................ 230Fuses ....................................... 230Engine compartment fuse box . 231Instrument panel fuse box ....... 233Load compartment fuse box .... 235

Vehicle tools .............................. 236Tools ........................................ 236

Wheels and tyres ....................... 238Winter tyres ............................. 238Tyre designations .................... 238Tyre pressure .......................... 238Tyre pressure monitoringsystem .................................... 239

Tread depth ............................. 243Changing tyre and wheel size . 244Wheel covers ........................... 244Tyre chains .............................. 244Tyre repair kit .......................... 245Wheel changing ....................... 248Spare wheel ............................ 250

Jump starting ............................. 253Towing ....................................... 255

Towing the vehicle ................... 255Towing another vehicle ........... 256

Appearance care ....................... 257Exterior care ............................ 257Interior care ............................. 258

General InformationAccessories and vehiclemodificationsWe recommend the use of genuineparts and accessories and factoryapproved parts specific for yourvehicle type. We cannot assess orguarantee reliability of other products- even if they have a regulatory orotherwise granted approval.Do not make any modifications to theelectrical system, e.g. changes ofelectronic control units (chip tuning).

Caution

When transporting the vehicle ona train or on a recovery vehicle, themud flaps might be damaged.

212 Vehicle care

Vehicle storageStorage for a long period of timeIf the vehicle is to be stored for severalmonths:● Wash and wax the vehicle.● Have the wax in the engine

compartment and underbodychecked.

● Clean and preserve the rubberseals.

● Fill up fuel tank completely.● Change the engine oil.● Drain the washer fluid reservoir.● Check the coolant antifreeze and

corrosion protection.● Adjust tyre pressure to the value

specified for full load.● Park the vehicle in a dry, well

ventilated place. Engage first orreverse gear or set selector leverto P. Prevent the vehicle fromrolling.

● Do not apply the parking brake.

● Open the bonnet, close all doorsand lock the vehicle.

● Disconnect the clamp from thenegative terminal of the vehiclebattery. Beware that all systemsare not functional, e.g. anti-theftalarm system.

Putting back into operationWhen the vehicle is to be put back intooperation:● Connect the clamp to the

negative terminal of the vehiclebattery. Activate the electronicsof the power windows.

● Check tyre pressure.● Fill up the washer fluid reservoir.● Check the engine oil level.● Check the coolant level.● Fit the number plate if necessary.

End-of-life vehicle recoveryInformation on end-of-life vehiclerecovery centres and the recycling ofend-of-life vehicles is available on ourwebsite, where legally required. Onlyentrust this work to an authorisedrecycling centre.

Vehicle care 213

Vehicle checksPerforming work

9 Warning

Only perform engine compartmentchecks when the ignition is off.The cooling fan may startoperating even if the ignition is off.

9 Danger

The ignition system usesextremely high voltage. Do nottouch.

BonnetOpening

Pull the release lever and return it toits original position.

Move the safety catch sideways to theleft vehicle side and open the bonnet.

Secure the bonnet support.

214 Vehicle care

If the bonnet is opened during anAutostop, the engine will be restartedautomatically for safety reasons.

ClosingBefore closing the bonnet, press thesupport into the holder.Lower the bonnet and let it fall into thelatch from a low height (20-25 cm).Check that the bonnet is engaged.

Caution

Do not press the bonnet into thelatch to avoid dents.

Engine oilCheck the engine oil level manuallyon a regular basis to prevent damageto the engine. Ensure that the correctspecification of oil is used.Recommended fluids and lubricants3 261.The maximum engine oilconsumption is 0.6 l per 1000 km.

Check with the vehicle on a levelsurface. The engine must be atoperating temperature and switchedoff for at least five minutes.

Caution

It is the owner's responsibility tomaintain the proper level of anappropriate quality oil in theengine.

Pull out the dipstick, wipe it clean,insert it to the stop on the handle, pullout and read the engine oil level.Insert dipstick to the stop on thehandle and make half a turn.Different dipsticks are useddepending on engine variant.

When the engine oil level hasdropped to the MIN mark, top upengine oil.

Vehicle care 215

We recommend the use of the samegrade of engine oil that was used atlast change.

The engine oil level must not exceedthe MAX mark on the dipstick.

Caution

Overfilled engine oil must bedrained or suctioned out.

Capacities 3 275.Fit the cap on straight and tighten it.

Engine coolantThe coolant provides freezeprotection down to approx. -28 °C. Incold regions with very lowtemperatures, the factory filledcoolant provides frost protectiondown to approx. -37 °C.

Caution

Only use approved antifreeze.

Coolant level

Caution

Too low a coolant level can causeengine damage.

If the cooling system is cold, thecoolant level should be above thefilling line mark. Top up if the level islow.

9 Warning

Allow the engine to cool beforeopening the cap. Carefully openthe cap, relieving the pressureslowly.

To top up, use a 1:1 mixture ofreleased coolant concentrate mixedwith clean tap water. If no coolantconcentrate is available, use cleantap water. Install the cap tightly. Have

216 Vehicle care

the coolant concentration checkedand have the cause of the coolantloss remedied by a workshop.

Washer fluid

Fill with clean water mixed with asuitable quantity of approvedwindscreen washer fluid whichcontains antifreeze.

Caution

Only washer fluid with a sufficientantifreeze concentration providesprotection at low temperatures ora sudden drop in temperature.

BrakesIn the event of minimum thickness ofthe brake lining, a squealing noisesounds during braking.Continued driving is possible buthave the brake lining replaced assoon as possible.Once new brake linings are installed,do not brake unnecessarily hard forthe first few journeys.

Brake fluid

9 Warning

Brake fluid is poisonous andcorrosive. Avoid contact with eyes,skin, fabrics and painted surfaces.

The brake fluid level must be betweenthe MIN and MAX marks.If fluid level is below MIN seek theassistance of a workshop.Brake and clutch fluid 3 261.

Vehicle care 217

Vehicle battery

The vehicle battery is located in theload compartment under the rear floorcover behind the rear seats. Rearfloor cover 3 79.There are connecting points for jumpstarting in the engine compartment.Jump starting 3 253.The vehicle battery is maintenance-free provided that the driving profileallows sufficient charging of thebattery. Short-distance-driving andfrequent engine starts can dischargethe battery. Avoid the use ofunnecessary electrical consumers.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.Laying up the vehicle for more thanfour weeks can lead to batterydischarge. Disconnect the clamp fromthe negative terminal of the vehiclebattery.Ensure the ignition is switched offbefore connecting or disconnectingthe vehicle battery.Vehicle battery discharge protection3 142.

Replacing the vehicle batteryNoticeAny deviation from the instructionsgiven in this section may lead totemporary deactivation of the stop-start system.

When the vehicle battery is beingreplaced, please ensure that thereare no open ventilation holes in thevicinity of the positive terminal. If aventilation hole is open in this area, itmust be closed off with a dummy cap,and the ventilation in the vicinity of thenegative terminal must be opened.In vehicles with an AGM (AbsorptiveGlass Mat) battery, make sure tohave the battery replaced withanother AGM battery.

An AGM battery can be identified bythe label on the battery. Werecommend the use of an originalVauxhall vehicle battery.

218 Vehicle care

NoticeUsing an AGM vehicle batterydifferent from the original Vauxhallvehicle battery may result in a lowerperformance.

We recommend that you have thevehicle battery replaced by aworkshop.Stop-start system 3 159.

Charging the vehicle battery

9 Warning

On vehicles with stop-startsystem, ensure that the chargingpotential does not exceed14.6 volts when using a batterycharger. Otherwise the vehiclebattery might be damaged.

Jump starting 3 253.

Warning label

Meaning of symbols:● No sparks, naked flames or

smoking.● Always shield eyes. Explosive

gases can cause blindness orinjury.

● Keep the vehicle battery out ofreach of children.

● The vehicle battery containssulphuric acid which could causeblindness or serious burninjuries.

● See the Owner's Manual forfurther information.

● Explosive gas may be present inthe vicinity of the vehicle battery.

Diesel fuel system bleedingIf the tank has been run dry, the dieselfuel system must be bled. Switch onthe ignition three times for15 seconds at a time. Then crank theengine for a maximum of40 seconds. Repeat this process afterno less than five seconds. If theengine fails to start, seek theassistance of a workshop.

Vehicle care 219

Wiper blade replacement

Lift the wiper arm until it stays in theraised position, press button todisengage the wiper blade andremove.Attach the wiper blade slightly angledto the wiper arm and push until itengages.Lower wiper arm carefully.

Wiper blade on the rear window

Lift wiper arm. Disengage wiper bladeas shown in illustration and remove.Attach the wiper blade slightly angledto the wiper arm and push until itengages.Lower wiper arm carefully.

Bulb replacementSwitch off the ignition and switch offthe relevant switch or close the doors.Only hold a new bulb at the base. Donot touch the bulb glass with barehands.Use only the same bulb type forreplacement.Replace headlight bulbs from withinthe engine compartment.

Bulb checkAfter a bulb replacement switch onthe ignition, operate and check thelights.

Halogen headlightsHalogen headlights with separatebulbs for low beam and high beam.

220 Vehicle care

Low beam (1) outer bulb.High beam (2) inner bulb.

Low beam (1)

1. Rotate the cap anticlockwise andremove it.

2. Disengage spring clip fromretainer by pulling. Withdraw thebulb holder from the reflector.

3. Detach the bulb from the bulbholder and replace the bulb.

4. Insert the bulb holder, engagingthe two lugs into the reflector androtate clockwise to secure.

5. Push spring clip back in place.6. Fit the cap and rotate clockwise.

High beam (2)

1. Rotate the cap anticlockwise andremove it.

Vehicle care 221

2. Disengage spring clip fromretainer by moving it forward andto the side. Swivel spring clipdownwards.

3. Withdraw the bulb holder from thereflector.

4. Detach the bulb from the bulbholder and replace the bulb.

5. Insert the bulb holder and installspring clip.Fit the cap and rotate clockwise.

Front turn signal lightIn case of defective LEDs, have themreplaced by a workshop.

Side lightIn case of defective LEDs, have themreplaced by a workshop.

Daytime running lightIn case of defective LEDs, have themreplaced by a workshop.

Fog lightsThe bulbs are accessible from theunderside of the vehicle.

1. Turn the bulb holder anti-clockwise and remove it from thereflector.

222 Vehicle care

2. Disengage the bulb socket fromthe plug connector by pressingthe retaining lug.

3. Remove and replace the bulbsocket with bulb and attach theplug connector.

4. Insert the bulb socket into thereflector by turning clockwise andengage.

Tail lights5-door Hatchback

1. Release the cover on therespective side and remove it.

2. Vehicles with tyre repair kit: Toreplace bulbs on the right side,first unscrew the plastic nut andtake out the insert with the sealantbottle.

3. Unscrew the plastic securing nutfrom the inside by hand.

Vehicle care 223

4. Carefully withdraw tail lightassembly from recess andremove.

5. Detach the cable from theretainer.

6. Press the three retaining lugs andremove the bulb carrier from thelight assembly.

7. Remove and replace the bulbs:Turn signal light (1)Tail light/brake light (2)

On version with LED tail lights andLED brake lights, only turn signallight bulb (1) can be removed andreplaced.

8. Attach the bulb carrier to the lightassembly.

9. Attach the cable to the retainer.10. Attach the light assembly to the

vehicle body and tighten thesecuring nut from the inside of theload compartment. Attach cover.

Depending on the version, tail lightsand brake lights are designed asLEDs. In case of failure, have LEDsreplaced by a workshop.

224 Vehicle care

Light assembly in the tailgate

1. Release the cover in the tailgateand remove it.

2. Unscrew the plastic securing nutby hand.

3. Carefully withdraw the lightassembly from the recesses andremove.

4. Detach the plug from the lightassembly.


Vehicle care 225

On version with LED tail lights, theposition of the retaining lugs isslightly different.

6. Remove and replace the bulb:Tail light (1)Rear fog light (2) (left side)Reverse light (2) (right side)

On version with LED tail lightsonly reverse light bulb (1) can beremoved and replaced.

7. Insert the bulb carrier into the taillight assembly. Attach plug to thelight assembly. Fit light assemblyon the tailgate and tighten thescrew from the inside. Attachcover.

Depending on the version, tail lightsare designed as LEDs. In case offailure, have LEDs replaced by aworkshop.

Sports Tourer

1. Release and open the cover onthe respective side.

226 Vehicle care

2. Unscrew both plastic securingnuts from the inside by hand.

3. Carefully withdraw tail lightassembly from recess andremove.

4. Detach the cable from theretainer.

5. Release the retaining lugs andremove the bulb carrier from thelight assembly.

6. Remove and replace the bulbs:Tail light/brake light (1)

Turn signal light (2)7. Insert the bulb carrier into the light

assembly.

8. On version with LED tail lights andbrake lights, only turn signal lightbulb can be replaced: removebulb holder in the light assemblyby turning. Replace bulb in thebulb holder.

9. Attach the cable to the retainer.10. Attach the light assembly to the

vehicle body and tighten thesecuring nuts from the inside ofthe load compartment. Attachcover.

Vehicle care 227

Depending on the version, tail lightsand brake lights are designed asLEDs. In case of failure, have LEDsreplaced by a workshop.

Light assembly in the tailgate

1. Release the cover in the tailgateand remove it.

2. Unscrew the plastic securing nutby hand.

3. Carefully withdraw the lightassembly from the recesses andremove.


228 Vehicle care

5. Remove and replace the bulb:Reverse light (1)Tail light (2)Rear fog light (3) (left side)

6. Insert the bulb carrier into the taillight assembly.

7. On version with LED tail lightsonly reverse light bulb can bereplaced: remove bulb holder inthe light assembly by turning.Replace bulb in the bulb holder.

8. Fit light assembly on the tailgateand tighten the securing nut fromthe inside. Attach cover.

Depending on the version, tail lightsare designed as LEDs. In case offailure, have LEDs replaced by aworkshop.

Side turn signal lightsTo replace bulb, remove lamphousing:

1. Slide lamp to its left side andremove with its right end.

2. Turn bulb holder anticlockwiseand remove from housing.

3. Pull bulb from bulb holder andreplace it.

Vehicle care 229

4. Insert bulb holder and turnclockwise.

5. Insert left end of the lamp, slide tothe left and insert right end.

Number plate light

1. Insert screwdriver in recess of thecover, press to the side andrelease spring.

2. Remove lamp downwards, takingcare not to pull on the cable.

3. Remove bulb holder from lamphousing by turning anticlockwise.

4. Pull bulb from bulb holder andreplace it.

5. Insert bulb holder into lamphousing and turn clockwise.

6. Insert lamp into bumper and letengage.

Some versions have LED numberplate lights. In case of defectiveLEDs, have them replaced by aworkshop.

Interior lightsCourtesy light, reading lightsHave bulbs replaced by a workshop.

Load compartment lightHave bulbs replaced by a workshop.

Instrument panelilluminationHave bulbs replaced by a workshop.

230 Vehicle care

Electrical systemFusesData on the replacement fuse mustmatch the data on the defective fuse.There are three fuse boxes in thevehicle:● engine compartment● instrument panel● load compartment

Before replacing a fuse, turn off therespective switch and the ignition.A blown fuse can be recognized by itsmelted wire. Do not replace the fuseuntil the cause of the fault has beenremedied.Some functions are protected byseveral fuses.Fuses may also be inserted withoutexistence of a function.

Fuse extractorA fuse extractor may be located in thefuse box in the engine compartment.

Place the fuse extractor on thevarious types of fuse from the top orside, and withdraw fuse.

Vehicle care 231

Engine compartment fusebox

The fuse box is in the front left of theengine compartment.Disengage the cover and remove it.

No. Circuit

1 Starter

2 Starter

3 Exhaust sensor

4 Engine control module

5 Engine functions

6 Transmission control module

7 –

8 Engine control module

9 Climate control system

10 Diesel exhaust system

11 Tailgate locking system, Trans‐mission

12 Seat lumbar massage

13 After boil pump


15 Exhaust sensor

16 Fuel injection

17 Fuel injection

232 Vehicle care

No. Circuit



20 –

21 DC/AC Converter

22 ABS

23 Washer system for windscreenand rear window

24 –

25 Diesel fuel heating


27 Power tailgate module

28 –

29 Heated rear window

30 Mirror defrost

31 –

32 DC transformer/LED display/Electrical heater/Climatecontrol/Glow plug controller

No. Circuit

33 Anti theft warning

34 Horn

35 Power outlet load compartment

36 Right high beam (Halogen)/Right low beam (LED)

37 Left high beam (Halogen)

38 LED headlight/Automatic head‐light range adjustment

39 Front fog light

40 OnStar

41 Water in fuel sensor/Waterpump

42 Manual headlight range adjust‐ment

43 Fuel pump

44 Rear view camera/Inside rearview mirror/Trailer module

45 LED headlight left/Automaticheadlight range adjustment left

No. Circuit

46 Instrument cluster

47 Steering column lock

48 Rear wiper

49 –

50 LED headlight right/Automaticheadlight range adjustmentright

51 Left low beam (LED)

52 Engine control module/Trans‐mission control module

53 –

54 Windscreen wiper


56 –

57 –

After having changed defective fuses,close the fuse box cover and pressuntil it engages.If the fuse box cover is not closedcorrectly, malfunction may occur.

Vehicle care 233

Instrument panel fuse boxThe fuse box is located behind acover.

Pull the cover and remove.Vehicles with power connector:If the fuse cover has a powerconnector, it must be removed byusing an adapter and a screwdriver.The adapter is stowed in the glovebox3 70. The screwdriver is stowed in theload compartment 3 236.

Attach the adapter to the powerconnector.

Push the screwdriver through therecess in the adapter. Remove thecover by pulling the screwdriver.

234 Vehicle care

No. Circuit

1 –

2 Climate control system, fan

3 Power seat driver side

4 Cigarette lighter/Power outletfront

5 –

6 Power window front

7 ABS

8 Heated steering wheel

9 Body control module

10 Power window rear

11 Sunroof


13 Seat heating (only on vehicleswithout alarm horn)

14 Exterior mirror



No. Circuit



19 Data link connector

20 Airbag system

21 Climate control system

22 Central locking system, tailgate

23 Electronic key system

24 Power seat memory function

25 Airbag system steering wheel

26 Ignition switch/Steering columnlock


28 USB socket

29 –

30 Selector lever

31 Rear window wiper


No. Circuit

33 Anti-theft alarm system/Powersounder

34 Parking assist/Side blind spotalert/Infotainment system/USBsocket

35 OnStar

36 Info display/Instrument cluster/CD player

37 Infotainment system, radio

After having changed defective fuses,close the fuse box cover and pressuntil it engages.Vehicles with power connector:1. Apply the cover on the right side.

Vehicle care 235

2. Fold the left side of the coverforwards. Take care that thesecuring clamp is guided asshown in the illustration.

Load compartment fuse boxThe fuse box is located on the left sideof the load compartment behind acover.

Remove the cover.

Disengage the fuse box cover andremove it.

236 Vehicle care

No. Circuit

1 –

2 DC/AC Inverter

3 Trailer module

4 Power seat passenger side

5 –

6 Distance warning module

7 –

8 –

9 Rear seat heating (on vehicleswithout alarm horn)

10 Service

11 –

12 Front seat heating (on vehicleswith alarm horn)

13 Rear seat heating (on vehicleswith alarm horn)

14 Ignition

15 Seat ventilation

No. Circuit

16 Trailer outlet

17 Trailer outlet

18 –

19 –

20 –

21 Electrical rear seat folding

22 Power tailgate

After having changed defective fuses,close the fuse box cover and pressuntil it engages.

Vehicle toolsTools5-door hatchback with sparewheelOpen the floor cover of the loadcompartment 3 79.

The jack, the towing eye, a strap forsecuring a damaged wheel and thetools are located in the tool box belowthe spare wheel. Spare wheel3 250.

Vehicle care 237

Sports Tourer with spare wheelOpen the floor cover of the loadcompartment 3 79.

The jack, the towing eye and the toolsare located in the tool box below thespare wheel. Spare wheel 3 250.

5-door hatchback with tyre repairkit

Open the cover in the right side wallof the load compartment.Some tools and the towing eye arelocated together with the tyre repairkit in a tool box.

Sports Tourer with tyre repair kit

Open the floor cover of the loadcompartment 3 79.The tools and the towing eye arelocated together with the tyre repairkit in a tool box.

238 Vehicle care

Wheels and tyres

Tyre condition, wheel conditionDrive over edges slowly and at rightangles if possible. Driving over sharpedges can cause tyre and wheeldamage. Do not trap tyres on the kerbwhen parking.Regularly check the wheels fordamage. Seek the assistance of aworkshop in the event of damage orunusual wear.

Winter tyresWinter tyres improve driving safety attemperatures below 7 °C and shouldtherefore be fitted on all wheels.All tyre sizes are permitted as wintertyres 3 276.In accordance with country-specificregulations, affix the speed sticker inthe driver's field of view.

Tyre designationsE.g. 215/60 R 16 95 H215 : Tyre width, mm60 : Cross-section ratio (tyre height

to tyre width), %R : Belt type: RadialRF : Type: RunFlat16 : Wheel diameter, inches95 : Load index e.g. 95 is

equivalent to 690 kgH : Speed code letter

Speed code letter:Q : up to 100 mphS : up to 112 mphT : up to 118 mphH : up to 130 mphV : up to 150 mphW : up to 168 mph

Choose a tyre appropriate for themaximum speed of your vehicle.The maximum speed is achievable atkerb weight with driver (75 kg) plus125 kg payload. Optional equipmentcould reduce the maximum speed ofthe vehicle.Performance 3 270.

Tyre pressureCheck the pressure of cold tyres atleast every 14 days and before anylong journey. Do not forget the sparewheel.This also applies to vehicles with tyrepressure monitoring system.Unscrew the valve cap.

Tyre pressure 3 276.The tyre pressure information labelon the left door frame indicates theoriginal equipment tyres and thecorrespondent tyre pressures.

Vehicle care 239

The tyre pressure data refers to coldtyres. It applies to summer and wintertyres.Always inflate the spare tyre to thepressure specified for full load.The ECO tyre pressure serves toachieve the smallest amount of fuelconsumption possible.Incorrect tyre pressures will impairsafety, vehicle handling, comfort andfuel economy and will increase tyrewear.Tyre pressures differ depending onvarious options. For the correct tyrepressure value, follow the procedurebelow:1. Identify the engine identifier code.

Engine data 3 268.2. Identify the respective tyre.

The tyre pressure tables show allpossible tyre combinations 3 276.For the tyres approved for yourvehicle, refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.

The driver is responsible for correctadjustment of tyre pressure.

9 Warning

If the pressure is too low, this canresult in considerable tyre warm-up and internal damage, leading totread separation and even to tyreblow-out at high speeds.

9 Warning

For specific tyres therecommended tyre pressure asshown in the tyre pressure tablemay exceed the maximum tyrepressure as indicated on the tyre.Never exceed the maximum tyrepressure as indicated on the tyre.

If the tyre pressure must be reducedor increased on a vehicle with tyrepressure monitoring system, switchoff ignition.

Temperature dependencyThe tyre pressure depends on thetemperature of the tyre. Duringdriving, tyre temperature andpressure increase. Tyre pressurevalues provided on the tyreinformation label and tyre pressurechart are valid for cold tyres, whichmeans at 20 °C.The pressure increases by nearly1.5 psi for a 10 °C temperatureincrease. This must be consideredwhen warm tyres are checked.The tyre pressure value displayed inthe Driver Information Centre showsthe real tyre pressure. A cooled downtyre will show a decreased value,which does not indicate an air leak.

Tyre pressure monitoringsystemThe tyre pressure monitoring systemchecks the pressure of all four tyresonce a minute when vehicle speedexceeds a certain limit.

240 Vehicle care

Caution

Tyre pressure monitoring systemwarns only about low tyre pressurecondition and does not replaceregular tyre maintenance by thedriver.

All wheels must be equipped withpressure sensors and the tyres musthave the prescribed pressure.NoticeIn countries where the tyre pressuremonitoring system is legallyrequired, the use of wheels withoutpressure sensors will invalidate thevehicle type approval.

The current tyre pressures can beshown in the Driver InformationCentre.Midlevel display:

Select the Tyre pressure page underthe Vehicle Information Menu ? inthe Driver Information Centre 3 113.Uplevel display:

Select the Tyre pressure page underthe Info Menu in the DriverInformation Centre 3 113.System status and pressure warningsare displayed by a messageindicating the corresponding tyre inthe Driver Information Centre.The system considers the tyretemperature for the warnings.Temperature dependency 3 238.

A detected low tyre pressurecondition is indicated by the controlindicator w 3 111.If w illuminates, stop as soon aspossible and inflate the tyres asrecommended 3 276.If w flashes for 60-90 seconds thenilluminates continuously, there is afault in the system. Consult aworkshop.

Vehicle care 241

After inflating, some driving may berequired to update the tyre pressurevalues in the Driver InformationCentre. During this time w mayilluminate.If w illuminates at lower temperaturesand extinguishes after driving, thiscould be an indicator for approachinga low tyre pressure condition. Checktyre pressure.Vehicle messages 3 120.If the tyre pressure must be reducedor increased, switch off ignition.Only mount wheels with pressuresensors, otherwise the tyre pressurewill not be displayed and willuminates continuously.A spare wheel or temporary sparewheel is not equipped with pressuresensors. The tyre pressuremonitoring system is not operationalfor these tyres. Control indicator willuminates. For the further threetyres, the system remainsoperational.

The use of commercially-availableliquid tyre repair kits can impair thefunction of the system. Factory-approved repair kits can be used.Operating electronic devices or beingclose to facilities using similar wavefrequencies could disrupt the tyrepressure monitoring system.Each time the tyres are replaced, tyrepressure monitoring system sensorsmust be dismounted and serviced.For the screwed sensor, replacevalve core and sealing ring. For theclipped sensor, replace completevalve stem.

Vehicle loading statusAdjust tyre pressure to load conditionaccording to the tyre information labelor tyre pressure chart 3 276, andselect the appropriate setting in theTyre load menu in the DriverInformation Centre 3 113. Thissetting is the reference for the tyrepressure warnings.

The Tyre load menu only appears ifthe vehicle is in a standstill and theparking brake is applied. On vehicleswith automatic transmission theselector lever has to be in P.Midlevel display:

Select the Tyre load page under theVehicle Information Menu ? in theDriver Information Centre 3 113.Select● Light for comfort pressure up to

three people.● Eco for Eco pressure up to three

people.● Max for full loading.

242 Vehicle care

Uplevel display:

Select the Tyre load page under theOptions Menu in the DriverInformation Centre 3 113.Select● Light for comfort pressure up to

three people.● Eco for Eco pressure up to

three people.● Max for full loading.

Tyre pressure sensor matchingprocessEach tyre pressure sensor has aunique identification code. Theidentification code must be matchedto a new wheel position after rotatingthe wheels or exchanging thecomplete wheel set and if one or moretyre pressure sensors were replaced.The tyre pressure sensor matchingprocess should also be performedafter replacing a spare wheel with aroad wheel containing the tyrepressure sensor.The malfunction light w and thewarning message or code should gooff at the next ignition cycle. Thesensors are matched to the wheelpositions, using a relearn tool, in thefollowing order: left side front wheel,right side front wheel, right side rearwheel and left side rear wheel. Theturn signal light at the current activeposition is illuminated until sensor ismatched.Consult a workshop for service orpurchase a relearn tool. There aretwo minutes to match the first wheelposition, and five minutes overall to

match all four wheel positions. If ittakes longer, the matching processstops and must be restarted.The tyre pressure sensor matchingprocess is:1. Apply the parking brake.2. Turn the ignition on.3. On vehicles with automatic

transmission: set the selectorlever to P.On vehicles with manualtransmission: select neutral.

4. Midlevel display:Use MENU on the turn signallever to select the VehicleInformation Menu ? in theDriver Information Centre.Uplevel display:Press p on the steering wheel toopen main menu page.Select the Info page with Q or P.Confirm with 9.

5. Select the tyre pressure menu.Midlevel display:

Vehicle care 243

Uplevel display:

6. Midlevel display:Press SET/CLR to begin thesensor matching process. Amessage requesting acceptance

of the process should bedisplayed.Press SET/CLR again to confirmthe selection. The horn soundstwice to indicate that the receiveris in relearn mode.Uplevel display:Press 9 to begin the sensormatching process. The hornsounds twice to indicate that thereceiver is in relearn mode.

7. Start with the left side front wheel.8. Place the relearn tool against the

tyre sidewall, near the valve stem.Then press the button to activatethe tyre pressure sensor. A hornchirp confirms that the sensoridentification code has beenmatched to this wheel position.

9. Proceed to the right side frontwheel, and repeat the procedurein Step 8.

10. Proceed to the right side rearwheel, and repeat the procedurein Step 8.

11. Proceed to the left side rearwheel, and repeat the procedurein Step 8. The horn sounds twice

to indicate that the sensoridentification code has beenmatched to the left side rearwheel, and the tyre pressuresensor matching process is nolonger active.

12. Turn off the ignition.13. Set all four tyres to the

recommended air pressure levelas indicated on the tyre pressureinformation label.

14. Ensure the tyre loading status isset according to the selectedpressure 3 113.

Tread depthCheck tread depth at regularintervals.Tyres should be replaced for safetyreasons at a tread depth of 2-3 mm(4 mm for winter tyres).For safety reasons it is recommendedthat the tread depth of the tyres onone axle should not vary by more than2 mm.

244 Vehicle care

The legally permissible minimumtread depth (1.6 mm) has beenreached when the tread has worndown as far as one of the tread wearindicators (TWI). Their position isindicated by markings on thesidewall.If there is more wear at the front thanthe rear, swap round front wheels andrear wheels periodically. Ensure thatthe direction of rotation of the wheelsremains the same.Tyres age, even if they are not used.We recommend tyre replacementevery six years.

Changing tyre and wheelsizeIf tyres of a different size than thosefitted at the factory are used, it may benecessary to reprogramme thespeedometer as well as the nominaltyre pressure and make other vehiclemodifications.After converting to a different tyresize, have the label with tyrepressures replaced.Furthermore, the advanced parkingassist must be calibrated 3 186.

9 Warning

Use of unsuitable tyres or wheelsmay lead to accidents and willinvalidate the vehicle typeapproval.

Wheel coversWheel covers and tyres that arefactory approved for the respectivevehicle and comply with all of therelevant wheel and tyre combinationrequirements must be used.

If the wheel covers and tyres used arenot factory approved, the tyres mustnot have a rim protection ridge.Wheel covers must not impair brakecooling.

9 Warning

Use of unsuitable tyres or wheelcovers could lead to suddenpressure loss and therebyaccidents.

Tyre chains

Tyre chains are only permitted on thefront wheels.

Vehicle care 245

Always use fine mesh chains that addno more than 10 mm to the tyre treadand the inboard sides (including chainlock).

9 Warning

Damage may lead to tyre blowout.

Tyre chains are permitted on tyres ofsize 195/65 R15, 205/55 R16 and215/55 R16.

Temporary spare wheelThe use of tyre chains is not permittedon the temporary spare wheel.

Tyre repair kitMinor damage to the tyre tread can berepaired with the tyre repair kit.Do not remove foreign bodies fromthe tyres.Tyre damage exceeding 4 mm or thatis at tyre's sidewall cannot be repairedwith the tyre repair kit.

9 Warning

Do not drive faster than 50 mph.Do not use for a lengthy period.Steering and handling may beaffected.

If you have a flat tyre:Apply the parking brake and engagefirst gear, reverse gear or P.

On 5-door hatchback the tyre repairkit is on the right side in the loadcompartment behind a cover.

On Sports Tourer the tyre repair kit isin the load compartment below thefloor cover.1. Remove the sealant bottle.2. Insert thumb into the opening and

pull out the compressor.

246 Vehicle care

3. Remove the electrical connectioncable and air hose from thestowage compartments on theunderside of the compressor.

4. Screw the compressor air hose tothe connection on the sealantbottle.

5. Fit the sealant bottle into theretainer on the compressor.Set the compressor near the tyrein such a way that the sealantbottle is upright.

6. Unscrew valve cap from defectivetyre.

7. Screw the filler hose to the tyrevalve.

8. The switch on the compressormust be set to J.

9. Connect the compressor plug tothe power outlet or cigarettelighter socket.To avoid discharging the battery,we recommend running theengine.

10. Set the rocker switch on thecompressor to I. The tyre is filledwith sealant.

11. The compressor pressure gaugebriefly indicates up to 6 bar whilstthe sealant bottle is emptying(approx. 30 seconds). Then thepressure starts to drop.

12. All of the sealant is pumped intothe tyre. Then the tyre is inflated.

Vehicle care 247

13. The prescribed tyre pressureshould be obtained within tenminutes. Tyre pressure 3 276.When the correct pressure isobtained, switch off thecompressor.

If the prescribed tyre pressure isnot obtained within ten minutes,remove the tyre repair kit. Movethe vehicle one tyre rotation.Reattach the tyre repair kit andcontinue the filling procedure forten minutes. If the prescribed tyrepressure is still not obtained, thetyre is too badly damaged. Seekthe assistance of a workshop.

Drain excess tyre pressure withthe button over the pressureindicator.Do not run the compressor longerthan ten minutes.

14. Detach the tyre repair kit. Pushcatch on bracket to removesealant bottle from bracket. Screwthe tyre inflation hose to the freeconnection of the sealant bottle.This prevents sealant fromescaping. Stow tyre repair kit inload compartment.

15. Remove any excess sealantusing a cloth.

16. Take the label indicatingmaximum permitted speed fromthe sealant bottle and affix in thedriver's field of view.

17. Continue driving immediately sothat sealant is evenly distributedin the tyre. After driving approx.six miles (but no more than tenminutes), stop and check tyrepressure. Screw compressor airhose directly onto tyre valve andcompressor when doing this.

If tyre pressure is more than1.3 bar, set it to the correct value.Repeat the procedure until thereis no more loss of pressure.If the tyre pressure has fallenbelow 1.3 bar, the vehicle mustnot be used. Seek the assistanceof a workshop.

18. Stow away tyre repair kit in loadcompartment.

248 Vehicle care

NoticeThe driving characteristics of therepaired tyre are severely affected,therefore have this tyre replaced.If unusual noise is heard or thecompressor becomes hot, turncompressor off for at least30 minutes.The built-in safety valve opens at apressure of seven bar (102 psi).Note the expiry date of the kit. Afterthis date its sealing capability is nolonger guaranteed. Pay attention tostorage information on sealantbottle.Replace the used sealant bottle.Dispose of the bottle as prescribedby applicable laws.The compressor and sealant can beused from approx. -30 °C.The adapters supplied can be usedto pump up other items e.g.footballs, air mattresses, inflatabledinghies etc. They are located on theunderside of the compressor. Toremove, screw on compressor airhose and withdraw adapter.

Wheel changingSome vehicles are equipped with atyre repair kit instead of a spare wheel3 245.Make the following preparations andobserve the following information:● Park the vehicle on a level, firm

and non-skid surface. The frontwheels must be in the straight-ahead position.

● Apply the parking brake andengage first gear, reverse gear orP.

● Remove the spare wheel 3 250.● Never change more than one

wheel at once.● Use the jack only to change

wheels in case of puncture, notfor seasonal winter or summertyre change.

● The jack is maintenance-free.● If the ground on which the vehicle

is standing is soft, a solid board(max. one cm thick) should beplaced under the jack.

● Take heavy objects out of thevehicle before jacking up.

● No people or animals may be inthe vehicle when it is jacked-up.

● Never crawl under a jacked-upvehicle.

● Do not start the vehicle when it israised on the jack.

● Clean wheel nuts and thread witha clean cloth before mounting thewheel.

9 Warning

Do not grease wheel bolt, wheelnut and wheel nut cone.

1. Disengage wheel nut caps with ascrewdriver and remove. For alloywheels, place a soft clothunderneath the screwdriver. Pulloff the wheel cover. Vehicle tools3 236.

Vehicle care 249

2. Fold out the wheel wrench andinstall ensuring that it locatessecurely and loosen each wheelnut by half a turn.

3. Ensure the jack is correctlypositioned under the relevantvehicle jacking point.

4. Set the jack to the necessaryheight. Position it directly belowthe jacking point in a manner thatprevents it from slipping.

Ensure that the edge of the bodyfits into the notch of the jack.

Attach wheel wrench and with thejack correctly aligned rotate wheelwrench until wheel is clear of the

250 Vehicle care

ground. Do not raise the jack anyfurther.

5. Unscrew the wheel nuts.6. Change the wheel. Spare wheel

3 250.7. Screw on the wheel nuts.8. Lower the vehicle and remove

jack.9. Install the wheel wrench ensuring

that it locates securely and tighteneach nut in a crosswisesequence. Tightening torque is140 Nm.

10. Align the valve hole in the wheelcover with the tyre valve beforeinstalling.Install wheel nut caps.

11. Stow the replaced wheel 3 250and the vehicle tools 3 236.

12. Check the tyre pressure of theinstalled tyre and the wheel nuttorque as soon as possible.

Have the defective tyre renewed orrepaired as soon as possible.

Jacking position for lifting platform

Rear arm position of the liftingplatform under the rear recess of thesill.

Front arm position of the liftingplatform at the underbody.

Spare wheelSome vehicles are equipped with atyre repair kit instead of a sparewheel.If mounting a spare wheel which isdifferent from the other wheels, thiswheel might be classified as atemporary spare wheel and thecorresponding speed limits apply,even though no label indicates this.Seek the assistance of a workshop tocheck the applicable speed limit.The spare wheel has a steel rim.

Caution

The use of a spare wheel that issmaller than the other wheels or incombination with winter tyrescould affect driveability. Have thedefective tyre replaced as soon aspossible.

Vehicle care 251

The spare wheel is located in the loadcompartment beneath the floorcovering.To remove:1. Open the floor cover 3 79.2. The spare wheel is secured with a

wing nut. Unscrew nut and takeout the spare wheel.Under the spare wheel there is thebox with vehicle tools.

3. When, after a wheel change, nowheel is placed in the spare wheelwell, secure the tool box bytightening the wing nut as far as itwill go and close floor cover.

4. After wheel change back to fullsize wheel, place the spare wheeloutside up in the well and securewith the wing nut.

Stowing a damaged full sizewheel in the load compartment, 5-door hatchbackThe spare wheel well is not designedfor other tyre sizes than the sparewheel. A damaged full size wheelmust be stowed in the loadcompartment and secured with astrap. Vehicle tools 3 236. To securethe wheel:1. Position the wheel outside up

close to one sidewall of the loadcompartment.

2. Place the loop end of the strapthrough the front lashing eye onthe appropriate side.

3. Place the hook end of the strapthrough the loop and pull it untilthe strap is fastened securely tothe lashing eye.

252 Vehicle care

4. Insert the strap through thespokes of the wheel as shown inthe illustration.

5. Mount the hook to the rear lashingeye.

6. Tighten the strap and secure itusing the buckle.

9 Danger

Always drive with folded up andengaged rear seat backrests whenstowing a damaged full size wheelin the load compartment.

Stowing a damaged full sizewheel in the load compartment,Sports TourerAll permitted wheel sizes can bestowed in the spare wheel well. Tosecure the wheel:

1. Remove centre cap with the brandemblem by pushing from theinside.

2. Position the wheel outside downin the wheel well.

3. Secure the defective wheel withthe wing nut.

4. Depending on the tyre size, thefloor cover can be placed on theprojecting wheel.

Temporary spare wheel

Caution

The use of a spare wheel that issmaller than the other wheels or incombination with winter tyrescould affect driveability. Have thedefective tyre replaced as soon aspossible.

Only mount one temporary sparewheel. Do not drive faster than50 mph. Take curves slowly. Do notuse for a long period of time.If your vehicle gets a flat tyre on therear while towing another vehicle,mount the temporary spare wheel inthe front and the full tyre in the rear.Tyre chains 3 244.

Vehicle care 253

Spare wheel with directional tyreIf possible, fit directional tyres suchthat they roll in the direction of travel.The rolling direction is indicated by asymbol (e.g. an arrow) on thesidewall.The following applies to tyres fittedopposing the rolling direction:● Driveability may be affected.

Have the defective tyre renewedor repaired as soon as possibleand fit it instead of the sparewheel.

● Drive particularly carefully on wetand snow-covered roadsurfaces.

Jump startingThe vehicle battery is located in theload compartment under a cover.There are connecting points for jumpstarting in the engine compartment.A vehicle with a discharged vehiclebattery can be started using jumpleads and the vehicle battery ofanother vehicle.Do not start with quick charger.

9 Warning

Be extremely careful when startingwith jump leads. Any deviationfrom the following instructions canlead to injuries or damage causedby battery explosion or damage tothe electrical systems of bothvehicles.

9 Warning

Avoid contact of the battery witheyes, skin, fabrics and paintedsurfaces. The fluid contains

sulphuric acid which can causeinjuries and damage in the eventof direct contact.

● Never expose the vehicle batteryto naked flames or sparks.

● A discharged vehicle battery canalready freeze at a temperatureof 0 °C. Defrost the frozen vehiclebattery before connecting jumpleads.

● Wear eye protection andprotective clothing whenhandling a vehicle battery.

● Use a booster vehicle batterywith the same voltage (12 Volt).Its capacity (Ah) must not bemuch less than that of thedischarged vehicle battery.

● Use jump leads with insulatedterminals and a cross section ofat least 16 mm2 (25 mm2 fordiesel engines).

● Do not disconnect the dischargedvehicle battery from the vehicle.

● Switch off all unnecessaryelectrical consumers.

254 Vehicle care

● Do not lean over the vehiclebattery during jump starting.

● Do not allow the terminals of onelead to touch those of the otherlead.

● The vehicles must not come intocontact with each other duringthe jump starting process.

● Apply the parking brake,transmission in neutral,automatic transmission in P.

● Open the positive terminalprotection cap of your vehicle inthe engine compartment and ofthe booster vehicle battery.

Lead connection order:1. Connect the red lead to the

positive terminal of the boostervehicle battery.

2. Connect the other end of the redlead to the positive terminal ofyour vehicle near the fuse box inthe engine compartment.

3. Connect the black lead to thenegative terminal of the boostervehicle battery.

4. Connect the other end of the blacklead to a vehicle grounding pointof your vehicle in the enginecompartment.

Route the leads so that they cannotcatch on rotating parts in the enginecompartment.To start the engine:1. Start the engine of the vehicle

providing the jump.2. After five minutes, start the other

engine. Start attempts should bemade for no longer than15 seconds at an interval of oneminute.

3. Allow both engines to idle forapprox. three minutes with theleads connected.

4. Switch on electrical consumers(e.g. headlights, heated rearwindow) of the vehicle receivingthe jump start.

5. Reverse above sequence exactlywhen removing leads.

Vehicle care 255

TowingTowing the vehicle

Insert a screwdriver in the slot at thelower part of the cap. Release the capby carefully moving the screwdriverdownwards.The towing eye is stowed with thevehicle tools 3 236.

Screw in the towing eye as far as it willgo until it stops in a horizontalposition.Attach a tow rope – or better still a towrod – to the towing eye.The towing eye must only be used fortowing and not for recovering thevehicle.Switch on ignition to release steeringwheel lock and to permit operation ofbrake lights, horn and windscreenwiper.Transmission in neutral.

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

When the engine is not running,considerably more force is needed tobrake and steer.To prevent the entry of exhaust gasesfrom the towing vehicle, switch on theair recirculation and close thewindows.Vehicles with automatic transmission:The vehicle must be towed facingforwards, not faster than 50 mph norfurther than 60 miles. In all othercases and when the transmission isdefective, the front axle must beraised off the ground.Vehicles with manual transmissionautomated: the vehicle must only betowed facing forwards with the frontaxle raised off the ground.Seek the assistance of a workshop.After towing, unscrew the towing eye.Insert cap at the top and engagedownwards.

256 Vehicle care

Towing another vehicle

Insert a screwdriver in the slot at thelower bend of the cap. Release thecap by carefully moving thescrewdriver downwards.The towing eye is stowed with thevehicle tools 3 236.

Screw in the towing eye as far as it willgo until it stops in a horizontalposition.The lashing eye at the rearunderneath the vehicle must never beused as a towing eye.Attach a tow rope – or even better atow bar – to the towing eye.The towing eye must only be used fortowing and not for recovering avehicle.

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

After towing, unscrew the towing eye.Insert cap at the top and engagedownwards.

Vehicle care 257

Appearance careExterior careLocksThe locks are lubricated at the factoryusing a high quality lock cylindergrease. Use de-icing agent only whenabsolutely necessary, as this has adegreasing effect and impairs lockfunction. After using a de-icing agent,have the locks regreased by aworkshop.

WashingThe paintwork of your vehicle isexposed to environmental influences.Wash and wax your vehicle regularly.When using automatic vehiclewashes, select a programme thatincludes waxing.Bird droppings, dead insects, resin,pollen and the like should be cleanedoff immediately, as they containaggressive constituents which cancause paint damage.

If using a vehicle wash, comply withthe vehicle wash manufacturer'sinstructions. The windscreen wiperand rear window wiper must beswitched off. Remove antenna andexternal accessories such as roofracks etc.If you wash your vehicle by hand,make sure that the insides of thewheel housings are also thoroughlyrinsed out.Clean edges and folds on openeddoors and the bonnet as well as theareas they cover.Clean bright metal mouldings with acleaning solution approved foraluminium to avoid damages.

Caution

Always use a cleaning agent witha pH value of four to nine.Do not use cleaning agents on hotsurfaces.

Do not clean the engine compartmentwith a steam-jet or high-pressure jetcleaner.

Thoroughly rinse and leather-off thevehicle. Rinse leather frequently. Useseparate leathers for painted andglass surfaces: remnants of wax onthe windows will impair vision.Have the door hinges of all doorsgreased by a workshop.

Exterior lightsHeadlight and other light covers aremade of plastic. Do not use anyabrasive or caustic agents, do not usean ice scraper, and do not clean themdry.

Polishing and waxingWax the vehicle regularly (at thelatest when water no longer beads).Otherwise, the paintwork will dry out.Polishing is necessary only if the painthas become dull or if solid depositshave become attached to it.Paintwork polish with silicone forms aprotective film, making waxingunnecessary.Plastic body parts must not be treatedwith wax or polishing agents.

258 Vehicle care

Windows and windscreen wiperbladesUse a soft lint-free cloth or chamoisleather together with window cleanerand insect remover.When cleaning the rear window frominside, always wipe in parallel to theheating element to prevent damage.For mechanical removal of ice, use asharp-edged ice scraper. Press thescraper firmly against the glass sothat no dirt can get under it andscratch the glass.Remove dirt residues from smearingwiper blades by using a soft cloth andwindow cleaner. Also make sure toremove any residues such as wax,insect residues and similar from thewindow.Ice residues, pollution and continuouswiping on dry windows will damage oreven destroy the wiper blades.

SunroofNever clean with solvents or abrasiveagents, fuels, aggressive media(e.g. paint cleaner, acetone-containing solutions etc.), acidic orhighly alkaline media or abrasivepads. Do not apply wax or polishingagents to the sunroof.

Wheels and tyresDo not use high-pressure jetcleaners.Clean rims with a pH-neutral wheelcleaner.Rims are painted and can be treatedwith the same agents as the body.

Paintwork damageRectify minor paintwork damage witha touch-up pen before rust forms.Have more extensive damage or rustareas repaired by a workshop.

UnderbodySome areas of the vehicle underbodyhave a PVC undercoating while othercritical areas have a durableprotective wax coating.

After the underbody is washed, checkthe underbody and have it waxed ifnecessary.Bitumen/rubber materials coulddamage the PVC coating. Haveunderbody work carried out by aworkshop.Before and after winter, wash theunderbody and have the protectivewax coating checked.

Towing equipmentDo not clean the coupling ball bar witha steam-jet or high-pressure jetcleaner.

Air shutterClean the shutter system in the frontbumper to maintain correctfunctionality.

Interior careInterior and upholsteryOnly clean the vehicle interior,including the instrument panel fasciaand panelling, with a dry cloth orinterior cleaner.

Vehicle care 259

Clean the leather upholstery withclear water and a soft cloth. In case ofheavy soiling, use leather care.The instrument cluster and thedisplays should only be cleaned usinga soft damp cloth. If necessary use aweak soap solution.Clean fabric upholstery with avacuum cleaner and brush. Removestains with an upholstery cleaner.Clothing fabrics may not becolourfast. This could cause visiblediscolourations, especially on light-coloured upholstery. Removablestains and discolourations should becleaned as soon as possible.Clean seat belts with lukewarm wateror interior cleaner.

Caution

Close Velcro fasteners as openVelcro fasteners on clothing coulddamage seat upholstery.The same applies to clothing withsharp-edged objects, like zips orbelts or studded jeans.

Plastic and rubber partsPlastic and rubber parts can becleaned with the same cleaner asused to clean the body. Use interiorcleaner if necessary. Do not use anyother agent. Avoid solvents and petrolin particular. Do not use high-pressure jet cleaners.

260 Service and maintenance

Service andmaintenance

General information ................... 260Service information .................. 260

Recommended fluids, lubricantsand parts .................................... 261

Recommended fluids andlubricants ................................ 261

General informationService informationIn order to ensure economical andsafe vehicle operation and tomaintain the value of your vehicle, itis of vital importance that allmaintenance work is carried out at theproper intervals as specified.The detailed, up-to-date serviceschedule for your vehicle is availableat the workshop.Service display 3 106.

European service intervalsMaintenance of your vehicle isrequired every 20,000 miles or afterone year, whichever occurs first,unless otherwise indicated in theservice display.A shorter service interval can be validfor severe driving behaviour, e.g. fortaxis and police vehicles.The European service intervals arevalid for the following countries:

Andorra, Austria, Belgium, Bosnia-Herzegovina, Bulgaria, Croatia,Cyprus, Czech Republic, Denmark,Estonia, Finland, France, Germany,Greece, Greenland, Hungary,Iceland, Ireland, Italy, Latvia,Liechtenstein, Lithuania,Luxembourg, Macedonia, Malta,Monaco, Montenegro, Netherlands,Norway, Poland, Portugal, Romania,San Marino, Serbia, Slovakia,Slovenia, Spain, Sweden,Switzerland, United Kingdom.Service display 3 106.

International service intervalsMaintenance of your vehicle isrequired every 10,000 miles or afterone year, whichever occurs first,unless otherwise indicated in theservice display.The international service intervals arevalid for the countries which are notlisted in the European serviceintervals.Service display 3 106.

Service and maintenance 261

ConfirmationsConfirmation of service is recorded inthe Service and warranty booklet.The date and mileage is completedwith the stamp and signature of theservicing workshop.Make sure that the Service andwarranty booklet is completedcorrectly as continuous proof ofservice is essential if any warranty orgoodwill claims are to be met, and isalso a benefit when selling thevehicle.

Service interval with remainingengine oil life durationThe service interval is based onseveral parameters depending onusage.The service display lets you knowwhen to change the engine oil.Service display 3 106.

Recommended fluids,lubricants and partsRecommended fluids andlubricantsOnly use products that meet therecommended specifications.

9 Warning

Operating materials arehazardous and could bepoisonous. Handle with care. Payattention to information given onthe containers.

Engine oilEngine oil is identified by its qualityand its viscosity. Quality is moreimportant than viscosity whenselecting which engine oil to use. Theoil quality ensures e.g. enginecleanliness, wear protection and oilaging control, whereas viscositygrade gives information on the oil'sthickness over a temperature range.

Dexos is the newest engine oil qualitythat provides optimum protection forgasoline and diesel engines. If it isunavailable, engine oils of other listedqualities have to be used.Recommendations for gasolineengines are also valid forCompressed Natural Gas (CNG),Liquified Petroleum Gas (LPG) andEthanol (E85) fuelled engines.Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 265.

Topping up engine oilEngine oils of different manufacturersand brands can be mixed as long asthey comply with the required engineoil quality and viscosity.Use of engine oil with onlyACEA A1/B1 or only A5/B5 quality isprohibited, since it can cause long-term engine damage under certainoperating conditions.Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 265.

262 Service and maintenance

Additional engine oil additivesThe use of additional engine oiladditives could cause damage andinvalidate the warranty.

Engine oil viscosity gradesThe SAE viscosity grade givesinformation of the thickness of the oil.Multigrade oil is indicated by twofigures, e.g. SAE 5W-30. The firstfigure, followed by a W, indicates thelow temperature viscosity and thesecond figure the high temperatureviscosity.Select the appropriate viscosity gradedepending on the minimum ambienttemperature 3 265.All of the recommended viscositygrades are suitable for high ambienttemperatures.

Coolant and antifreezeUse only organic acid type-long lifecoolant (LLC) antifreeze approved forthe vehicle. Consult a workshop.The system is factory filled withcoolant designed for excellentcorrosion protection and frostprotection down to approx. -28 °C. In

northern countries with very lowtemperatures the factory filled coolantprovides frost protection down toapprox. -37 °C. This concentrationshould be maintained all year round.The use of additional coolantadditives that intend to give additionalcorrosion protection or seal againstminor leaks can cause functionproblems. Liability for consequencesresulting from the use of additionalcoolant additives will be rejected.

Brake and clutch fluidOver time, brake fluid absorbsmoisture which will reduce brakingeffectiveness. The brake fluid shouldtherefore be replaced at the specifiedinterval.

Technical data 263

Technical data

Vehicle identification .................. 263Vehicle Identification Number .. 263Identification plate ................... 263Engine identification ................ 264

Vehicle data ............................... 265Recommended fluids andlubricants ................................ 265

Engine data ............................. 268Performance ............................ 270Vehicle weight ......................... 272Vehicle dimensions ................. 274Capacities ................................ 275Tyre pressures ........................ 276

Vehicle identificationVehicle IdentificationNumber

The Vehicle Identification Numbermay be stamped on the identificationplate and on the floor pan, under thefloor covering, visible under a cover.The Vehicle Identification Numbermay be embossed on the instrumentpanel, visible through the windscreen,or in the engine compartment on theright body panel.

Identification plate

The identification plate is located onthe front left or right door frame.

264 Technical data

Information on identification label:1 : manufacturer2 : type approval number3 : vehicle identification number4 : permissible gross vehicle weight

rating in kg5 : permissible gross train weight

in kg6 : maximum permissible front axle

load in kg7 : maximum permissible rear axle

load in kg8 : vehicle-specific or country-

specific data

The combined total of front and rearaxle loads must not exceed thepermissible gross vehicle weight. Forexample, if the front axle is bearing itsmaximum permissible load, the rearaxle can only bear a load that is equalto the gross vehicle weight minus thefront axle load.The technical data is determined inaccordance with EuropeanCommunity standards. We reservethe right to make modifications.Specifications in the vehicledocuments always have priority overthose given in this manual.

Engine identificationThe technical data tables show theengine identifier code. Engine data3 268.To identify the respective engine,refer to the engine power in the EECCertificate of Conformity providedwith your vehicle or other nationalregistration documents.

Technical data 265

Vehicle dataRecommended fluids and lubricantsEuropean service schedule

Required engine oil qualityAll European countries with European service interval 3 260

Engine oil quality Petrol engines(including CNG, LPG, E85)

Diesel engines

dexos 1 – –

dexos 2 ✔ ✔

In case dexos quality is unavailable you may use max. one litre engine oil quality ACEA C3 once between each oil change.

Engine oil viscosity gradesAll European countries with European service interval 3 260

Ambient temperature Petrol and diesel engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

266 Technical data

International service schedule

Required engine oil qualityAll countries with international service interval 3 260


Diesel engines

dexos 1 (if available) ✔ –

dexos 2 ✔ ✔

In case dexos quality is unavailable you may use the oil qualities listed below:

All countries with international service interval 3 260


Diesel engines

GM-LL-A-025 ✔ –

GM-LL-B-025 – ✔



Diesel engines

ACEA A3/B3 ✔ –

ACEA A3/B4 ✔ ✔

Technical data 267


ACEA C3 ✔ ✔

API SM ✔ –

API SN resource conserving ✔ –

Engine oil viscosity gradesAll countries with international service interval 3 260

Ambient temperature Petrol and diesel engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

down to -20 °C SAE 10W-301) or SAE 10W-401)

1) Permitted, but usage of SAE 5W-30 or SAE 5W-40 with dexos quality is recommended.

268 Technical data

Engine dataEngine identifier code B10XFL B14XE B14XFL B14XFT B16SHTSales designation 1.0 1.4 1.4 1.4 1.6Engineering code B10XFT B14XE B14XFT B14XFT B16SHT

Piston displacement [cm3] 999 1399 1399 1399 1598

Engine power [kW] 77 74 92 110 147

at rpm 4500-6000 6000 4000-5600 5000-5600 5500

Torque [Nm] 170 130 245/2302) 245/2302) 280

at rpm 1800-4300 4300 2000-3500 2000-4000 1650-5000

Fuel type Petrol Petrol Petrol Petrol Petrol

Octane rating RON3)

recommended 95 95 95 95 98

possible 98 98 98 98 95

possible 91 91 91 91 91

Additional fuel type – – – – –

2) With Stop-start system.3) A country specific label at the fuel filler flap can supersede the engine specific requirement.

Technical data 269

Engine identifier code B16DTC B16DTE B16DTU B16DTHB16DTRSales designation 1.6 1.6 1.6 1.61.6Engineering code B16DTE B16DTE B16DTU B16DTHB16DTR

Piston displacement [cm3] 1598 1598 1598 15981598

Engine power [kW] 70 81 81 100118

at rpm 3500 3500 3500 3500-40004000

Torque [Nm] 280 300 300 320350

at rpm 1500-1750 1750-2000 1750-2000 2000-22501500-2250

Fuel type Diesel Diesel Diesel DieselDiesel

270 Technical data

Performance5-door Hatchback

Engine B10XFL B14XE B14XFL B14XFT B16SHT

Maximum speed [mph]

Manual transmission 124 115 127 134 146

Manual transmission automated 124 – – – –

Automatic transmission – – – 130 –

Engine B16DTC B16DTE B16DTU B16DTH B16DTR

Maximum speed [mph]


– – – – –


Technical data 271

Sports Tourer

Engine B10XFL B14XE B14XFL B14XFT B16SHT

Maximum speed [mph]


Manual transmission automated 124 – – – –


Engine B16DTC B16DTE B16DTU B16DTH B16DTR

Maximum speed [mph]


– – – – –


272 Technical data

Vehicle weightKerb weight, basic model without any optional equipment

5-door Hatchback Engine Manualtransmission

Manual transmissionautomated

Automatictransmission

without/withair conditioning[kg]

B10XFL 1263/1273 1263/1273 –

B14XE 1234/1244 – –

B14XFL –/1278 – –

B14XFT –/1278 – –/1308

B16SHT –/1350 – –

B16DTC 1335/1345 – –

B16DTE 1350/1360 – –

B16DTU 1335/1345 – –

B16DTH 1350/1360 – –/1364

B16DTR 1396/1406 – –

Optional equipment and accessories increase the kerb weight.Loading information 3 87.

Technical data 273

Kerb weight, basic model without any optional equipment

Sports Tourer Engine Manual transmission Manual transmission automated Automatic transmission

without/with air conditioning[kg]

B10XFL 1278/1288 1278/1288 –

B14XE 1263/1273 – –

B14XFL –/1322 – –

B14XFT –/1322 – –/1350

B16SHT –/1393 – –

B16DTC 1378/1388 – –

B16DTE 1393/1403 – –

B16DTU 1393/1403 – –

B16DTH –/1393 – –/1425

B16DTR 1425/1435 – –

Optional equipment and accessories increase the kerb weight.Loading information 3 87.

274 Technical data

Vehicle dimensions5-door hatchback Sports Tourer

Length [mm] 4370 4702

Width without exterior mirrors [mm] 1809 1809

Width with two exterior mirrors [mm] 2042 2042

Height (without antenna) [mm] 1437-1531 1452-1580

Length of load compartment floor [mm] 828 1065

Length of load compartment with folded rear seats [mm] 1575 1872

Load compartment width [mm] 1001 1050

Load compartment height [mm] 588 399

Wheelbase [mm] 2662 2662

Turning circle diameter [m] 11.05-11.44 11.05-11.44

Technical data 275

CapacitiesEngine oil

Engine B10XFL B14XFL,B14XFT,B14XE

B16DTU B16DTC,B16DTE,B16DTH,B16DTR

B16SHT

including Filter [l] 4.0 4.0 4.5 5.0 5.5

between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0

Fuel tank

Petrol/diesel, refilling quantity [l] 48

276 Technical data

Tyre pressures5-door hatchback Comfort with up to 3 people ECO with up to 3 people With full loadEngine Tyres front rear front rear front rear

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

B10XFL,B14XE

195/65 R15,225/45 R17

220/2.2 (32) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39)

205/55 R16 220/2.2 (32) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 270/2.7 (39)

B14XFL 195/65 R15,225/45 R17,225/40 R18

220/2.2 (32) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39)

205/55 R16 220/2.2 (32) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 270/2.7 (39)

B14XFT 195/65 R15,225/45 R17,215/55 R16,215/50 R17,225/40 R18

220/2.2 (32) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39)

205/55 R16 220/2.2 (32) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 270/2.7 (39)

Technical data 277

5-door hatchback Comfort with up to 3 people ECO with up to 3 people With full loadEngine Tyres front rear front rear front rear

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

B16DTE,B16DTH

225/45 R17,225/40 R18

240/2.4 (35) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39)

205/55 R16 240/2.4 (35) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 270/2.7 (39)

B16DTR,B16SHT

225/45 R17 240/2.4 (35) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39)

225/40 R18 260/2.6 (38) 240/2.4 (35) 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 290/2.9 (42)

205/55 R16 240/2.4 (35) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 270/2.7 (39)

B16DTC,B16DTU

195/65 R15,225/45 R17

240/2.4 (35) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39)

205/55 R16 240/2.4 (35) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 270/2.7 (39)

All Temporary sparewheel115/70 R16

420/4.2 (60) 420/4.2 (60) – – 420/4.2 (60) 420/4.2 (60)

278 Technical data

Sports Tourer Comfort with up to 3 people ECO with up to 3 people With full loadEngine Tyres front rear front rear front rear

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

B10XFL,B14XE

195/65 R15,225/45 R17

220/2.2 (32) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39)

205/55 R16 220/2.2 (32) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 270/2.7 (39)

B14XFL 195/65 R15,225/45 R17,225/40 R18

220/2.2 (32) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39)

205/55 R16 220/2.2 (32) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 270/2.7 (39)

B14XFT 195/65 R15,225/45 R17,225/40 R18

250/2.5 (36) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39)

205/55 R16 250/2.5 (36) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 270/2.7 (39)

B16DTE,B16DTH

225/45 R17,225/40 R18

240/2.4 (35) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39)

205/55 R16 240/2.4 (35) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 270/2.7 (39)

Technical data 279

Sports Tourer Comfort with up to 3 people ECO with up to 3 people With full loadEngine Tyres front rear front rear front rear

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

B16DTR,B16SHT

225/45 R17 240/2.4 (35) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 290/2.9 (42)

225/40 R18 260/2.6 (38) 240/2.4 (35) 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 300/3.0 (43)

205/55 R16 240/2.4 (35) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 290/2.9 (42)

B16DTC,B16DTU

195/65 R15,225/45 R17

240/2.4 (35) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39)

205/55 R16 240/2.4 (35) 220/2.2 (32) 300/3.0 (43) 300/3.0 (43) 250/2.5 (36) 270/2.7 (39)

All Temporary sparewheel115/70 R16

420/4.2 (60) 420/4.2 (60) – – 420/4.2 (60) 420/4.2 (60)

280 Customer information

Customerinformation

Customer information ................ 280Declaration of conformity ......... 280Collision damage repair ........... 280Software acknowledgement .... 280

Vehicle data recording and pri‐vacy ........................................... 282

Event data recorders ............... 282Radio Frequency Identification(RFID) ..................................... 283

Customer informationDeclaration of conformityRadio transmission systemsThis vehicle has systems thattransmit and/or receive radio wavessubject to Directive 1999/5/EC.These systems are in compliancewith the essential requirements andother relevant provisions ofDirective 1999/5/EC. Copies of theoriginal Declarations of Conformitycan be obtained on our website.

Collision damage repairPaint thicknessDue to production techniques, thethickness of the paint can varybetween 50 and 400 µm.Therefore, different paint thickness isno indicator for a collision damagerepair.

Software acknowledgementCertain OnStar components includelibcurl and unzip software and otherthird party software. Below are thenotices and licenses associated withlibcurl and unzip and for other thirdparty software please see http://www.lg.com/global/support/opensource/index.

libcurlCopyright and permission noticeCopyright (c) 1996 - 2010, DanielStenberg, <[email protected]>.All rights reserved.Permission to use, copy, modify, anddistribute this software for anypurpose with or without fee is herebygranted, provided that the abovecopyright notice and this permissionnotice appear in all copies.The software is provided "as is",without warranty of any kind, expressor implied, including but not limited tothe warranties of merchantability,fitness for a particular purpose andnoninfringement of third party rights.

Customer information 281

In no event shall the authors orcopyright holders be liable for anyclaim, damages or other liability,whether in an action of contract, tortor otherwise, arising from, out of or inconnection with the software or theuse or other dealings in the software.Except as contained in this notice, thename of a copyright holder shall notbe used in advertising or otherwise topromote the sale, use or otherdealings in this Software without priorwritten authorization of the copyrightholder.

unzipThis is version 2005-Feb-10 of theInfo-ZIP copyright and license. Thedefinitive version of this documentshould be available at ftp://ftp.info-zip.org/pub/infozip/license.htmlindefinitely.Copyright (c) 1990-2005 Info-ZIP. Allrights reserved.For the purposes of this copyright andlicense, “Info-ZIP” is defined as thefollowing set of individuals:

Mark Adler, John Bush, Karl Davis,Harald Denker, Jean-Michel Dubois,Jean-loup Gailly, Hunter Goatley, EdGordon, Ian Gorman, Chris Herborth,Dirk Haase, Greg Hartwig, RobertHeath, Jonathan Hudson, PaulKienitz, David Kirschbaum, JohnnyLee, Onno van der Linden, IgorMandrichenko, Steve P. Miller, SergioMonesi, Keith Owens, GeorgePetrov, Greg Roelofs, Kai UweRommel, Steve Salisbury, DaveSmith, Steven M. Schweda, ChristianSpieler, Cosmin Truta, AntoineVerheijen, Paul von Behren, RichWales, Mike White.This software is provided “as is,”without warranty of any kind, expressor implied. In no event shall Info-ZIPor its contributors be held liable forany direct, indirect, incidental, specialor consequential damages arising outof the use of or inability to use thissoftware.Permission is granted to anyone touse this software for any purpose,including commercial applications,and to alter it and redistribute it freely,subject to the following restrictions:

1. Redistributions of source codemust retain the above copyrightnotice, definition, disclaimer, andthis list of conditions.

2. Redistributions in binary form(compiled executables) mustreproduce the above copyrightnotice, definition, disclaimer, andthis list of conditions indocumentation and/or othermaterials provided with thedistribution. The sole exception tothis condition is redistribution of astandard UnZipSFX binary(including SFXWiz) as part of aself-extracting archive; that ispermitted without inclusion of thislicense, as long as the normalSFX banner has not beenremoved from the binary ordisabled.

3. Altered versions--including, butnot limited to, ports to newoperating systems, existing portswith new graphical interfaces, anddynamic, shared, or static libraryversions--must be plainly markedas such and must not bemisrepresented as being theoriginal source. Such altered

282 Customer information

versions also must not bemisrepresented as being Info-ZIPreleases--including, but notlimited to, labeling of the alteredversions with the names “Info-ZIP” (or any variation thereof,including, but not limited to,different capitalizations), “PocketUnZip,” “WiZ” or “MacZip” withoutthe explicit permission of Info-ZIP.Such altered versions are furtherprohibited from misrepresentativeuse of the Zip-Bugs or Info-ZIP e-mail addresses or of the Info-ZIPURL(s).

4. Info-ZIP retains the right to usethe names “Info-ZIP,” “Zip,”“UnZip,” “UnZipSFX,” “WiZ,”“Pocket UnZip,” “Pocket Zip,” and“MacZip” for its own source andbinary releases.

Vehicle data recordingand privacyEvent data recordersData storage modules in thevehicleA large number of electroniccomponents of your vehicle containdata storage modules temporarily orpermanently storing technical dataabout the condition of the vehicle,events and errors. In general, thistechnical information documents thecondition of parts, modules, systemsor the environment:● operating conditions of system

components (e.g. filling levels)● status messages of the vehicle

and its single components (e.g.number of wheel revolutions /rotational speed, deceleration,lateral acceleration)

● dysfunctions and defects inimportant system components

● vehicle reactions in particulardriving situations (e.g. inflation ofan airbag, activation of thestability regulation system)

● environmental conditions (e.g.temperature)

These data are exclusively technicaland help identifying and correctingerrors as well as optimising vehiclefunctions.Motion profiles indicating travelledroutes cannot be created with thesedata.If services are used (e.g. repairworks, service processes, warrantycases, quality assurance),employees of the service network(manufacturer included) are able toread out this technical informationfrom the event and error data storagemodules applying special diagnosticdevices. If required, you will receivefurther information at theseworkshops. After an error has beencorrected, the data are deleted fromthe error storage module or they areconstantly overwritten.

Customer information 283

When using the vehicle, situationsmay occur in which these technicaldata related to other information(accident report, damages on thevehicle, witness statements etc.) maybe associated with a specific person -possibly, with the assistance of anexpert.Additional functions contractuallyagreed upon with the client (e.g.vehicle location in emergency cases)allow the transmission of particularvehicle data from the vehicle.

Radio FrequencyIdentification (RFID)RFID technology is used in somevehicles for functions such as tyrepressure monitoring and ignitionsystem security. It is also used inconnection with conveniences suchas radio remote controls for doorlocking/unlocking and starting, and in-vehicle transmitters for garage dooropeners. RFID technology inVauxhall vehicles does not use orrecord personal information or linkwith any other Vauxhall systemcontaining personal information.

284

Index AAccessories and vehicle

modifications .......................... 211Active emergency braking.......... 184Adjustable air vents ................... 151Airbag and belt tensioners ......... 108Airbag deactivation .............. 62, 108Airbag label................................... 57Airbag system .............................. 57Air conditioning regular

operation ................................ 152Air conditioning system .............. 144Air intake .................................... 152Air vents...................................... 151Antilock brake system ................ 172Antilock brake system (ABS) ..... 110Anti-theft alarm system ................ 35Anti-theft locking system .............. 35Appearance care........................ 257Armrest................................... 52, 54Armrest storage ........................... 71Ashtrays ....................................... 98Automatic anti-dazzle .................. 40Automatic light control ............... 133Automatic locking ........................ 28Automatic transmission ............. 165Autostop..................................... 159Auxiliary heater........................... 151

BBattery discharge protection ...... 142Battery voltage ........................... 122Belts.............................................. 55Bonnet ....................................... 213Brake and clutch fluid................. 261Brake and clutch system ........... 109Brake assist ............................... 175Brake fluid .................................. 216Brakes ............................... 172, 216Breakdown.................................. 255Bulb replacement ....................... 219

CCapacities .................................. 275Cargo management system ........ 81Catalytic converter ..................... 165Central locking system ................ 23Centre console lighting .............. 141Changing tyre and wheel size . . . 244Charging system ........................ 108Child locks ................................... 29Child restraint installation

locations ................................... 66Child restraints.............................. 63Child restraint systems ................ 63Climate control ............................. 15Climate control systems............. 143Clock............................................. 94Collision damage repair.............. 280

285

Control indicators........................ 107Control of the vehicle ................. 154Controls........................................ 90Convex shape .............................. 38Coolant and antifreeze............... 261Cruise control .................... 112, 178Cupholders .................................. 70Curtain airbag system .................. 61Curve lighting.............................. 134

DDanger, Warnings and Cautions . . . 4Daytime running lights ............... 134Declaration of conformity............ 280Diesel fuel system bleeding ....... 218Diesel particle filter .................... 164Door open .................................. 113Doors............................................ 29Driver assistance systems.......... 178Driver Information Centre........... 113Driving characteristics and

towing tips .............................. 206Driving hints................................ 154

EElectric adjustment ...................... 38Electrical system......................... 230Electric parking brake......... 109, 173Electric parking brake fault......... 109Electronic climate control system 146

Electronic driving programmes ......................................... 167, 171

Electronic key system................... 21Electronic Stability Control.......... 176Electronic Stability Control and

Traction Control system.......... 110Electronic Stability Control off..... 110End-of-life vehicle recovery ....... 212Engine compartment fuse box ... 231Engine coolant ........................... 215Engine coolant temperature

gauge ..................................... 105Engine data ............................... 268Engine exhaust .......................... 164Engine identification................... 264Engine oil ................... 214, 261, 265Engine oil pressure .................... 111Entry lighting .............................. 141Event data recorders.................. 282Exit lighting ................................ 141Exterior care .............................. 257Exterior light ............................... 112Exterior lighting .................... 12, 132Exterior mirrors............................. 38

FFault ................................... 168, 172First aid kit ................................... 85Fixed air vents ........................... 151Fog light ..................................... 112

Fog lights ................................... 221Folding mirrors ............................. 38Following distance...................... 110Following distance indication...... 184Forward collision alert................. 181Fragrance diffuser........................ 97Front airbag system ..................... 60Front fog lights ........................... 138Front seats.................................... 46Front storage................................ 71Fuel............................................. 203Fuel consumption - CO2-

Emissions ............................... 204Fuel for diesel engines .............. 203Fuel for petrol engines ............... 203Fuel gauge ................................. 105Fuses ......................................... 230

GGauges....................................... 103Gear shifting............................... 110General information ................... 205Glovebox ..................................... 70

HHalogen headlights .................... 219Hand brake......................... 172, 173Hazard warning flashers ............ 137Headlight flash ........................... 133Headlight range adjustment ...... 133Headlights................................... 132

286

Headlights when driving abroad 134Head restraint adjustment ............. 8Head restraints ............................ 45Heated mirrors ............................. 39Heated rear window ..................... 42Heated steering wheel ................. 91Heating .................................. 53, 54Heating and ventilation system . 143High beam ......................... 112, 133High beam assist........................ 112Hill start assist ........................... 175Horn ....................................... 13, 91

IIdentification plate ..................... 263Ignition switch positions ............. 154Immobiliser .......................... 37, 112Indicators.................................... 103Info display................................. 118Information displays.................... 113Instrument cluster ...................... 100Instrument panel fuse box ......... 233Instrument panel illumination ..... 229Instrument panel illumination

control .................................... 140Instrument panel overview ........... 10Interior care ............................... 258Interior lighting............................ 140Interior lights ...................... 140, 229Interior mirrors.............................. 39

Interruption of power supply ...... 168Introduction .................................... 3

JJump starting ............................. 253

KKey, memorised settings.............. 23Keys ............................................. 19Keys, locks................................... 19

LLane keep assist................ 110, 201Lashing eyes ............................... 80LED headlights................... 112, 134Lighting features......................... 141Light switch ................................ 132Load compartment ................ 29, 72Load compartment cover ............. 78Load compartment fuse box ...... 235Loading information ..................... 87Low fuel ..................................... 111

MMalfunction indicator light .......... 109Manual anti-dazzle ...................... 39Manual mode ..................... 167, 171Manual seat adjustment............... 47Manual transmission .................. 169Manual transmission automated 169Manual windows .......................... 40

Massage....................................... 54Maximum speed......................... 238Memorised settings...................... 23Midlevel display.......................... 113Mirror adjustment ........................... 9Misted light covers ..................... 139

NNew vehicle running-in .............. 154Number plate light ..................... 229

OObject detection systems........... 186Odometer ................................... 104Oil, engine.......................... 261, 265OnStar........................................ 128Outside temperature .................... 94Overrun cut-off ........................... 159

PParking ................................ 18, 162Parking assist ............................ 186Parking brake ............................ 173Parking lights ............................. 139Particulate filter........................... 164Performance .............................. 270Performing work ........................ 213Pollen filter ................................. 152Power button.............................. 155Power connector........................... 97Power outlets ............................... 96

287

Power seat adjustment ................ 49Power windows ............................ 40Preheating ................................. 111Puncture..................................... 248

QQuickheat................................... 151

RRadio Frequency Identification

(RFID)..................................... 283Radio remote control ................... 20Reading lights ............................ 140Rear floor storage cover .............. 79Rear fog light ..................... 112, 139Rear seats.................................... 54Rear view camera ...................... 195Rear window wiper/washer .......... 93Recommended fluids and

lubricants ........................ 261, 265Refuelling ................................... 203Retained power off..................... 156Reversing lights ......................... 139Ride control systems.................. 175Roof.............................................. 43Roof load...................................... 87Roof rack ..................................... 86

SSafety belts................................... 55Safety net .................................... 83

Seat adjustment ............................. 7Seat belt ........................................ 8Seat belt reminder ..................... 107Seat belts ..................................... 55Seat heating

Seat heating, front..................... 53Seat heating, rear..................... 54

Seat position ................................ 46Selector lever ..................... 166, 170Service ............................... 152, 260Service display .......................... 106Service information .................... 260Side airbag system ...................... 60Side blind spot alert.................... 194Sidelights.................................... 132Side turn signal lights ................ 228Software acknowledgement....... 280Spare wheel ............................... 250Speed limiter....................... 112, 180Speedometer ............................. 103Sport mode ................................ 177Starting and operating................ 154Starting off ................................... 16Starting the engine .................... 157Steering...................................... 154Steering wheel adjustment ...... 9, 90Steering wheel controls ............... 90Stop-start system........................ 159Storage......................................... 70Storage compartments................. 70

Sunroof ........................................ 43Sunvisor lights ........................... 141Sun visors .................................... 42Symbols ......................................... 4

TTachometer ............................... 105Tail lights ................................... 222Three-point seat belt .................... 56Tools .......................................... 236Tow bar....................................... 205Towing................................ 205, 255Towing another vehicle ............. 256Towing equipment ..................... 207Towing the vehicle ..................... 255Traction Control system ............. 175Traction Control system off......... 111Traffic sign assistant........... 113, 197Trailer coupling........................... 205Trailer stability assist ................. 210Trailer towing ............................. 206Transmission ............................... 15Transmission display ......... 165, 170Tread depth ............................... 243Trip odometer ............................ 104Turn and lane-change signals ... 138Turn signal ................................. 107Tyre chains ................................ 244Tyre designations ...................... 238Tyre pressure ............................ 238

288

Tyre pressure monitoringsystem............................. 111, 239

Tyre pressures ........................... 276Tyre repair kit ............................. 245

UUltrasonic parking assist............. 186Upholstery.................................. 258Uplevel display........................... 113Using this manual .......................... 3

VValet mode................................. 118Vehicle battery ........................... 217Vehicle checks............................ 213Vehicle data................................ 265Vehicle data recording and

privacy..................................... 282Vehicle detected ahead.............. 112Vehicle dimensions .................... 274Vehicle Identification Number .... 263Vehicle jack................................ 236Vehicle messages ..................... 120Vehicle personalisation ............. 122Vehicle security............................ 35Vehicle specific data ...................... 3Vehicle storage........................... 212Vehicle tools............................... 236Vehicle unlocking ........................... 6Vehicle weight ........................... 272

Ventilating..................................... 53Ventilation................................... 143

WWarning chimes ......................... 121Warning lights............................. 103Warning triangle .......................... 85Washer and wiper systems ......... 13Washer fluid ............................... 216Wheel changing ......................... 248Wheel covers ............................. 244Wheels and tyres ....................... 238Windows....................................... 40Windscreen................................... 40Windscreen wiper/washer ........... 91Winter tyres ............................... 238Wiper blade replacement .......... 219

Copyright by General Motors UK Ltd.

The information contained in this publication is effective as of the date indicated below. General Motors UK Ltd. reserves the rightto make changes to the technical specifications, features and design of the vehicles relative to the information contained in thispublication, as well as changes to the publication itself.

Edition: February 2016, General Motors UK Ltd.

Printed on chlorine-free bleached paper.

*KTA-2775/2-VX-EN*

KTA-2775/2-VX-en 02/2016

Date post:	17-Feb-2019
Category:	Documents
Upload:	ngokhuong
View:	226 times
Download:	1 times

Vauxhall Astra Owner's Manual · This Owner's Manual depicts left-hand drive vehicles. Operation is...

Documents