Date post: | 03-Jun-2018 |
Category: |
Documents |
Upload: | gilto-plata |
View: | 223 times |
Download: | 0 times |
of 48
8/12/2019 Ventiladores Inyeccin Oficinas
1/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 87 92 93 92 91 87 79 74 95 83 38
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
46
2
26.375
42.5
Model: SBPS-42-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 2
Weight w/o Acc's (lb) 218
Weight w/ Acc's (lb) 432
Max T Motor Frame Size 184
Optional Damper (in.) 42 x 42
Wall Opening (in.) 47.625 x 47.625
PerformanceRequested Volume (CFM) 12,954
Actual Volume (CFM) 12,954
External SP (in. wg) 0.48
Total SP (in. wg) 0.48
Fan RPM 934
Operating Power (hp) 1.91
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 4.9
Tip Speed (ft/min) 10,273
Motor
Motor Mounted Yes
Size (hp) 3
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 4.8
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/201Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S2-1 yMark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 1 of
8/12/2019 Ventiladores Inyeccin Oficinas
2/48
Model: SBPS-42-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-42-S - Short, 42Damper: WD430-42X42 - Gravity
10/10/201Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S2-1 yMark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 2 of
8/12/2019 Ventiladores Inyeccin Oficinas
3/48DAMPER
42
42
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/201Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S2-1 yMark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 3 of
8/12/2019 Ventiladores Inyeccin Oficinas
4/48
46.125
1.5
46.125
44
Standard Construction Features:
Notes: All dimensions shown are in units of in.
Short Wall Housing
10/10/201Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S2-1 yMark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 4 of
8/12/2019 Ventiladores Inyeccin Oficinas
5/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 83 93 87 85 84 82 76 70 89 78 29
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
34
1.25
20
30.375
Model: SBPS-30-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 3
Weight w/o Acc's (lb) 111
Weight w/ Acc's (lb) 259
Max T Motor Frame Size 184
Optional Damper (in.) 31 x 31
Wall Opening (in.) 35.625 x 35.625
PerformanceRequested Volume (CFM) 7,436
Actual Volume (CFM) 7,436
External SP (in. wg) 0.46
Total SP (in. wg) 0.46
Fan RPM 1171
Operating Power (hp) 1.1
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 5.9
Tip Speed (ft/min) 9,199
Motor
Motor Mounted Yes
Size (hp) 1 1/2
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 3
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/201Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S2-3,4 yMark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 5 of
8/12/2019 Ventiladores Inyeccin Oficinas
6/48
Model: SBPS-30-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-30-S - Short, 30Damper: WD430-31X31 - Gravity
10/10/201Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S2-3,4 yMark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 6 of
8/12/2019 Ventiladores Inyeccin Oficinas
7/48DAMPER
31
31
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/201Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S2-3,4 yMark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 7 of
8/12/2019 Ventiladores Inyeccin Oficinas
8/48
34.125
1.5
34.125
38
Standard Construction Features:
Notes: All dimensions shown are in units of in.
Short Wall Housing
10/10/201Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S2-3,4 yMark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 8 of
8/12/2019 Ventiladores Inyeccin Oficinas
9/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 86 91 85 82 80 78 73 69 86 74 25
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
28
1.25
18
24.375
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 6
Weight w/o Acc's (lb) 92
Weight w/ Acc's (lb) 211
Max T Motor Frame Size 145
Optional Damper (in.) 25 x 25
Wall Opening (in.) 29.625 x 29.625
PerformanceRequested Volume (CFM) 4,688
Actual Volume (CFM) 4,688
External SP (in. wg) 0.52
Total SP (in. wg) 0.52
Fan RPM 1321
Operating Power (hp) 0.83
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 6.6
Tip Speed (ft/min) 8,302
Motor
Motor Mounted Yes
Size (hp) 1
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 2.1
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S7-54 a 5Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 9 of
8/12/2019 Ventiladores Inyeccin Oficinas
10/48
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-24-S - Short, 24Damper: WD430-25X25 - Gravity
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S7-54 a 5Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 10 of
8/12/2019 Ventiladores Inyeccin Oficinas
11/48DAMPER
25
25
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S7-54 a 5Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 11 of
8/12/2019 Ventiladores Inyeccin Oficinas
12/48
28.125
1.5
28.125
37
Standard Construction Features:
Notes: All dimensions shown are in units of in.
Short Wall Housing
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S7-54 a 5Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 12 of
8/12/2019 Ventiladores Inyeccin Oficinas
13/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 87 90 85 81 79 77 72 68 85 73 24
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
28
1.25
18
24.375
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 6
Weight w/o Acc's (lb) 92
Weight w/ Acc's (lb) 211
Max T Motor Frame Size 145
Optional Damper (in.) 25 x 25
Wall Opening (in.) 29.625 x 29.625
PerformanceRequested Volume (CFM) 4,040
Actual Volume (CFM) 4,040
External SP (in. wg) 0.5
Total SP (in. wg) 0.5
Fan RPM 1252
Operating Power (hp) 0.7
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 7.2
Tip Speed (ft/min) 7,867
Motor
Motor Mounted Yes
Size (hp) 1
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 2.1
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S7-60 a 6Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 13 of
8/12/2019 Ventiladores Inyeccin Oficinas
14/48
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-24-S - Short, 24Damper: WD430-25X25 - Gravity
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S7-60 a 6Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 14 of
8/12/2019 Ventiladores Inyeccin Oficinas
15/48DAMPER
25
25
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S7-60 a 6Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 15 of
8/12/2019 Ventiladores Inyeccin Oficinas
16/48
28.125
1.5
28.125
37
Standard Construction Features:
Notes: All dimensions shown are in units of in.
Short Wall Housing
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-S7-60 a 6Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 16 of
8/12/2019 Ventiladores Inyeccin Oficinas
17/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 86 91 85 82 80 78 73 69 85 74 24
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
28
1.25
18
24.375
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 6
Weight w/o Acc's (lb) 92
Weight w/ Acc's (lb) 211
Max T Motor Frame Size 145
Optional Damper (in.) 25 x 25
Wall Opening (in.) 29.625 x 29.625
PerformanceRequested Volume (CFM) 4,660
Actual Volume (CFM) 4,660
External SP (in. wg) 0.48
Total SP (in. wg) 0.48
Fan RPM 1283
Operating Power (hp) 0.76
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 6.9
Tip Speed (ft/min) 8,062
Motor
Motor Mounted Yes
Size (hp) 1
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 2.1
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-6 a Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 17 of
8/12/2019 Ventiladores Inyeccin Oficinas
18/48
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-24-S - Short, 24Damper: WD430-25X25 - Gravity
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-6 a Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 18 of
8/12/2019 Ventiladores Inyeccin Oficinas
19/48DAMPER
25
25
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-6 a Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 19 of
8/12/2019 Ventiladores Inyeccin Oficinas
20/48
28.125
1.5
28.125
37
Standard Construction Features:
Notes: All dimensions shown are in units of in.
Short Wall Housing
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-6 a Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 20 of
8/12/2019 Ventiladores Inyeccin Oficinas
21/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 87 90 84 81 79 77 72 67 85 73 23
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
28
1.25
18
24.375
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 6
Weight w/o Acc's (lb) 75
Weight w/ Acc's (lb) 194
Max T Motor Frame Size 145
Optional Damper (in.) 25 x 25
Wall Opening (in.) 29.625 x 29.625
PerformanceRequested Volume (CFM) 4,012
Actual Volume (CFM) 4,012
External SP (in. wg) 0.48
Total SP (in. wg) 0.48
Fan RPM 1230
Operating Power (hp) 0.67
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 7.3
Tip Speed (ft/min) 7,729
Motor
Motor Mounted Yes
Size (hp) 3/4
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 1.6
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-12 a Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 21 of
8/12/2019 Ventiladores Inyeccin Oficinas
22/48
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-24-S - Short, 24Damper: WD430-25X25 - Gravity
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-12 a Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 22 of
8/12/2019 Ventiladores Inyeccin Oficinas
23/48DAMPER
25
25
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-12 a Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 23 of
8/12/2019 Ventiladores Inyeccin Oficinas
24/48
28.125
1.5
28.125
37
Standard Construction Features:
Notes: All dimensions shown are in units of in.
Short Wall Housing
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-12 a Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 24 of
8/12/2019 Ventiladores Inyeccin Oficinas
25/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 86 91 85 82 80 78 73 69 85 74 24
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
28
1.25
18
24.375
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 6
Weight w/o Acc's (lb) 92
Weight w/ Acc's (lb) 211
Max T Motor Frame Size 145
Optional Damper (in.) 25 x 25
Wall Opening (in.) 29.625 x 29.625
PerformanceRequested Volume (CFM) 4,660
Actual Volume (CFM) 4,660
External SP (in. wg) 0.48
Total SP (in. wg) 0.48
Fan RPM 1283
Operating Power (hp) 0.76
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 6.9
Tip Speed (ft/min) 8,062
Motor
Motor Mounted Yes
Size (hp) 1
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 2.1
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-18 a 2Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 25 of
8/12/2019 Ventiladores Inyeccin Oficinas
26/48
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-24-S - Short, 24Damper: WD430-25X25 - Gravity
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-18 a 2Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 26 of
8/12/2019 Ventiladores Inyeccin Oficinas
27/48DAMPER
25
25
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-18 a 2Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 27 of
8/12/2019 Ventiladores Inyeccin Oficinas
28/48
28.125
1.5
28.125
37
Standard Construction Features:
Notes: All dimensions shown are in units of in.
Short Wall Housing
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-18 a 2Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 28 of
8/12/2019 Ventiladores Inyeccin Oficinas
29/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 87 90 84 81 79 77 72 67 85 73 23
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
28
1.25
18
24.375
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 6
Weight w/o Acc's (lb) 75
Weight w/ Acc's (lb) 194
Max T Motor Frame Size 145
Optional Damper (in.) 25 x 25
Wall Opening (in.) 29.625 x 29.625
PerformanceRequested Volume (CFM) 4,012
Actual Volume (CFM) 4,012
External SP (in. wg) 0.48
Total SP (in. wg) 0.48
Fan RPM 1230
Operating Power (hp) 0.67
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 7.3
Tip Speed (ft/min) 7,729
Motor
Motor Mounted Yes
Size (hp) 3/4
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 1.6
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-24 a 2Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 29 of
8/12/2019 Ventiladores Inyeccin Oficinas
30/48
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-24-S - Short, 24Damper: WD430-25X25 - Gravity
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-24 a 2Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 30 of
8/12/2019 Ventiladores Inyeccin Oficinas
31/48DAMPER
25
25
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-24 a 2Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 31 of
8/12/2019 Ventiladores Inyeccin Oficinas
32/48
28.125
1.5
28.125
37
Standard Construction Features:
Notes: All dimensions shown are in units of in.
Short Wall Housing
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-24 a 2Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 32 of
8/12/2019 Ventiladores Inyeccin Oficinas
33/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 86 91 85 82 80 78 73 69 85 74 24
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
28
1.25
18
24.375
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 6
Weight w/o Acc's (lb) 92
Weight w/ Acc's (lb) 211
Max T Motor Frame Size 145
Optional Damper (in.) 25 x 25
Wall Opening (in.) 29.625 x 29.625
PerformanceRequested Volume (CFM) 4,660
Actual Volume (CFM) 4,660
External SP (in. wg) 0.48
Total SP (in. wg) 0.48
Fan RPM 1283
Operating Power (hp) 0.76
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 6.9
Tip Speed (ft/min) 8,062
Motor
Motor Mounted Yes
Size (hp) 1
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 2.1
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-30 a 3Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 33 of
8/12/2019 Ventiladores Inyeccin Oficinas
34/48
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-24-S - Short, 24Damper: WD430-25X25 - Gravity
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-30 a 3Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 34 of
8/12/2019 Ventiladores Inyeccin Oficinas
35/48DAMPER
25
25
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-30 a 3Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 35 of
8/12/2019 Ventiladores Inyeccin Oficinas
36/48
28.125
1.5
28.125
37
Standard Construction Features:
Notes: All dimensions shown are in units of in.
Short Wall Housing
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-30 a 3Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 36 of
8/12/2019 Ventiladores Inyeccin Oficinas
37/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 87 90 84 81 79 77 72 67 85 73 23
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
28
1.25
18
24.375
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 6
Weight w/o Acc's (lb) 75
Weight w/ Acc's (lb) 194
Max T Motor Frame Size 145
Optional Damper (in.) 25 x 25
Wall Opening (in.) 29.625 x 29.625
PerformanceRequested Volume (CFM) 4,012
Actual Volume (CFM) 4,012
External SP (in. wg) 0.48
Total SP (in. wg) 0.48
Fan RPM 1230
Operating Power (hp) 0.67
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 7.3
Tip Speed (ft/min) 7,729
Motor
Motor Mounted Yes
Size (hp) 3/4
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 1.6
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-36 a 4Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 37 of
8/12/2019 Ventiladores Inyeccin Oficinas
38/48
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-24-S - Short, 24Damper: WD430-25X25 - Gravity
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-36 a 4Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 38 of
8/12/2019 Ventiladores Inyeccin Oficinas
39/48DAMPER
25
25
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-36 a 4Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 39 of
8/12/2019 Ventiladores Inyeccin Oficinas
40/48
28.125
1.5
28.125
37
Standard Construction Features:
Notes: All dimensions shown are in units of in.
Short Wall Housing
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-36 a 4Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 40 of
8/12/2019 Ventiladores Inyeccin Oficinas
41/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 86 91 85 82 80 78 73 69 86 74 24
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
28
1.25
18
24.375
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 6
Weight w/o Acc's (lb) 92
Weight w/ Acc's (lb) 211
Max T Motor Frame Size 145
Optional Damper (in.) 25 x 25
Wall Opening (in.) 29.625 x 29.625
PerformanceRequested Volume (CFM) 4,660
Actual Volume (CFM) 4,660
External SP (in. wg) 0.5
Total SP (in. wg) 0.5
Fan RPM 1301
Operating Power (hp) 0.79
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 6.8
Tip Speed (ft/min) 8,173
Motor
Motor Mounted Yes
Size (hp) 1
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 2.1
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-42 a 4Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 41 of
8/12/2019 Ventiladores Inyeccin Oficinas
42/48
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-24-S - Short, 24Damper: WD430-25X25 - Gravity
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-42 a 4Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 42 of
8/12/2019 Ventiladores Inyeccin Oficinas
43/48DAMPER
25
25
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-42 a 4Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 43 of
8/12/2019 Ventiladores Inyeccin Oficinas
44/48
28.125
1.5
28.125
37
Standard Construction Features:
Notes: All dimensions shown are in units of in.
Short Wall Housing
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-42 a 4Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 44 of
8/12/2019 Ventiladores Inyeccin Oficinas
45/48
Sound Power by Octave BandSound
Data62.5 125 250 500 1000 2000 4000 8000 LwA dBA Sones
Inlet 87 90 84 81 79 77 72 67 85 73 23
SUPPLY FANS CAN CARRY RAIN
OR SNOW INTO THE BUILDING
AIR FLOW
See the Assembly Drawing For
Selected Accessories
28
1.25
18
24.375
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
DimensionalQuantity 6
Weight w/o Acc's (lb) 75
Weight w/ Acc's (lb) 194
Max T Motor Frame Size 145
Optional Damper (in.) 25 x 25
Wall Opening (in.) 29.625 x 29.625
PerformanceRequested Volume (CFM) 4,012
Actual Volume (CFM) 4,012
External SP (in. wg) 0.48
Total SP (in. wg) 0.48
Fan RPM 1230
Operating Power (hp) 0.67
Elevation (ft) 7,347
Airstream Temp.(F) 70
Air Density (ft3) 0.057
Drive Loss (%) 7.3
Tip Speed (ft/min) 7,729
Motor
Motor Mounted Yes
Size (hp) 3/4
V/C/P 460/60/3
Enclosure ODP
Motor RPM 1725
Windings 1
NEC FLA* (Amps) 1.6
Notes:All dimensions shown are in units of in..
*FLA - based on tables 150 or 148 of National Electrical
Code 2002. Actual motor FLA may vary, for sizing thermal
overload, consult factory.
LwA - A weighted sound power level, based on ANSI S1.4
dBA - A weighed sound pressure level, based on 11.5 dB
attenuation per Octave band at 5.0 ft - dBA levels are not
licensed by AMCA International
Sones - calculated using AMCA 301 at 5.0 ft
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-48 a 5Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 45 of
8/12/2019 Ventiladores Inyeccin Oficinas
46/48
Model: SBPS-24-3H
Sidewall Belt Drive Supply Fan
Standard Construction Features:Model SBPS is belt driven with fabricated steel or cast aluminum blades
depending on the level of construction. Model SBPS is suitable for supply in clean
air applications including factories and warehouses. Propellers are available in
three levels of construction from commercial to industrial. Multiple blade designs
for low sound and optimum efficiency. The "L-type" design is for low static
pressures and low sound levels. The "H-type" design is for higher static
pressures. Fans feature adjustable motor pulleys to allow for final system
balancing.
- Die formed, galvanized steel drive frame assembly - Level 1: galvanized steel
blades - Level 2: reinforced galvanized steel blades - Level 3: cast aluminum
blades - Assembled motor and drives - Static-resistant belts - Adjustable motor
pulley - Ball bearing motors - Fan shaft mounted in ball bearing pillow blocks -
Corrosion-resistant fasteners - UL/cUL 705 Electrical (Model SBP)
Options & Accessories:
Wall Housing: HSG-24-S - Short, 24Damper: WD430-25X25 - Gravity
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-48 a 5Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 46 of
8/12/2019 Ventiladores Inyeccin Oficinas
47/48DAMPER
25
25
Standard Construction Features:
Damper WD430 is used in vertical mount systems to allow airflow in one direction and prevent airflow in the opposite
direction.Available as gravity backdraft, WD430 is constructed of galvanized steel with aluminum blades. WD430 (flange on
ntake) can be used in vertical supply applications and is recommended for velocities up to 2,500 fpm or 2 in. wg.
Damper Configuration:
Actuator Type: Gravity
Notes: All dimensions shown are in units of in.
Width And height furnished approximately 0.125 in. undersize
Vertical Mount Intake Damper
Model: WD430
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-48 a 5Mark:
CAPS 4.12.1241 I:\Jobs\MASTER PLAN II REINGENIERIA SOTANOS.gfcj Page 47 of
8/12/2019 Ventiladores Inyeccin Oficinas
48/48
28.125
1.5
28.125
37
Standard Construction Features:
Short Wall Housing
10/10/20Printed Date:MASTER PLAN II REINGENIERIA SOTANOJob:
VIO-ST-48 a 5Mark: