3 + 2 Axis For High Performance Complete Machining Centre
Featuresl Siemens Sinumerik control 828D with 15.6 inch touch display l Heavy duty version l High productivityl Tool changer, Drum type tool changer with 24 tool positions l Direct spindles (inline spindles)l Closed electrical cabinet with integrated heat exchanger; ensures optimal temperature even in case of high ambient temperatures; prevents dirt particle penetration l Automatic centralised lubrication l Integrated machine lamp in work space l Chip conveyor, belt type ensures effi cient chip dischargel Chip carriage l High-performance oil cooler for spindle cooling and ball screw spindlel CTS 20 bar internal (we recommend an extractor)l Coolant gun l Portable, electronic handwheel l Ethernetl EMC (electromagnetic compatibility) and safety module by Siemensl RJ45 plug-in connection, USB connection and power connection 230 V
Included as Standardl Safety Integrated l Residual material detection and machining l ShopMill work step programmingl Managing network drives l 3-D simulation lSimultanous recording lPPU 290 with SW 28x system software
Control with control panel featuring PPU 290l 15.6" colour display l 16:9 format l Capacitive display with Multi-Touch controller l Intuitive Multi-Touch control l Soft key selection via touch function l Proximity sensor/clearance sensor for smart display controll Front panel made of die-cast magnesium with scratchproof glass frontl No battery (permanent intermediate data storage thanks to NV-RAM technology)l No fan l No hard disk l Can be operated while wearing glovesl Front interfaces: USB 2.0, RJ45 Ethernet, IP65 also with protective flap open
3 + 2 Axis For High Performance Complete Machining Centre
With Siemens 828D Controller
Electrical connection 400V. 3ph.50HZTotal Connected Load 31 KVASpindle Drive Motor S1 Op 15 kW Drive Motor Torque S1 Op 20 Nm Drive Motor S6 30% op 22.5 kW Drive Motor Torque S6 30% Op 62 NmSpindle taper SK 40 DIN 69871 Spindle Centre to Z axis cover 596 mm
Clear Spindle to table 100 - 500 mmRepeat Accuracy ± 0.005 /300 mmPositioning accuracy ± 0.005 Tool changer type Double arm grabNo. of tools 24Max Tool dia. 80 mmMax Tool dia. adjacent free slot 130 mm Tool Length 245 mmMax Tool weight 8 KgTool Change time tool to tool 2 seconds
X axis Travel 400 mm
Y axis Travel 560 mmZ axis Travel 400 mmSpeed Travel axis A Max 25 rpmSpeed Rotation axis B Max 25 rpm Acceleration X, Y Z axis 6 m / sec
Rapid Motion X,Y Z axis 48000 mm/min
Max Spindle Speed 15000 RpmCompressed air 6 barCoolant /Lub.Tank Capacity 260 Litres Tilting & Rotating Table Dia. 320 mm Tilting & Rotating Table Height 1160 mm Table Indexing A axis 60 sec Table Indexing C axis 20 secSwivel Angle A axis ± 120° / - 30°Rotation Range C axis 360°T-slot /amount/distance 14mm/ 7 / 75 mmMax Load bearing Cap. 100 KgDims LxWxH cm 226 x 299 x 296Weight 5,000 Kg
Specification FU 3
l 1 pc Face milling holder 27 mml 1 pc Chuck 1 - 13 mml 2 pc Weldon 6 mm l 1 pc Weldon 8,10,12 & 16mml 2 pc Weldon 20mm
l 1 pc Adaptor SK 40 to MT 3l 3 pc Collet chuck holder ER32l 1pc Spring collet spanner ER 32l 18pc Spring collet set ER 32l 1pc Height-adjuster
l 1pc Assembly and tool adjustment gauge l 1pc Taper squeegeel 15 pc pull studs
l Load-bearing capacity of up to 100 kgl Diameter 320 mm
TILITING AND ROTATING TABLE
l For amazing versatility of machine applicationsl Clearance spindle to table 100 - 500 mm
Featuresl Siemens Sinumerik control 828D with 15.6 inch touch display l Profile rail with recirculating rollers on all axes for high load bearing capacity l Tool changer, double arm grab with 30 tool slotsl Precision ground, pree-load, high-performance ball screws (Ø 40 mm x P16 x C3) on all axesl Main spindle SK40 up to 10,000 rpm with belt drive l Torsion free machine base thanks to strong ribbingl High-torque servo drives mounted directly on the ball screws on all three axes l Chip conveyor, belt type ensures efficient chip discharge l Chip carriage l Integrated machine lamp in work space l Coolant system with 520 litre coolant tank & chip flushing system l Cleaning gun l Portable, elect handwheel l RJ45 plug-in connection, USB connection & 230V power connection l Telescopic guide rail covers on all three axes l Closed electrical cabinet with integrated heat exchanger; ensures optimal temperature even in case of high ambient temperatures; prevents dirt particle penetration l Oil separator l Including two years SIEMENS warranty
Included as Standard
l Siemens 828D Controller with 15.6 inch touch display l Double arm grab with 30 tool slots
Electrical Connection 400V 3Ph 50Hz Tool Change Time 2 SecTotal Connected Load 40 KVA X axis Travel 1,050 mmDrive Motor S1 op 11 kW Y axis Travel 600 mmTorque Drive motor S1 70 Nm Z axis Travel 600 mmDrive Motor S6 30% Op 31.4 kW Rapid Motion X,Y Z axis 30,000 mm/minTorque Drive Motor S6 200 Nm X axis Motor Torque 18 NmCoolant Pump Motors 930Wx2+850 Y axis Motor Torque 18 NmCoolant Tank Cap. 520 Litres Z axis Motor Torque 27 Nm Repeat Accuracy ± 0.005 mm Spindle Speed Max 10,000 RpmPositioning Accuracy ± 0.005 mm Compressed Air 6 BarTool Changer Type Double arm grab Spindle to Table 100 - 750 mmNo.of Tools 30 Table Length x Width 1,200 x 600 mm Max Tool Dia. Ø80 mm T-Slot / Amount / Dist. 16mm/6/100mmMax Tool dia. adj. free slot Ø125 mm Max Load Bearing Cap. 800 KgTool Length 300 mm Dims LxWxH cm 327 x 260 x 274Max Tool Weight 8 Kg Weight 7,000 Kg
Featuresl Heavy duty version l High productivity l High reliability l Profile rail with ball screw for rapid speeds on all axes l High toqrue servo drives on all three axis l Torsion free machines base due to strong ribbing l Solid, precision milling table with four T-grooves l Screw auger type chip conveyor l Machine lamp in the workspace l RJ45 plug in connection, USB connection & 230V power connection l Coolant unit with 20 Litre tank & chip flushing system l Closed switch cabinet with integrated heat exchanger; ensures optimal temperature even incase of high ambient temperatures; prevents dirt particle penetration l Portable electronic hand wheel l Telescopic guide rail covers on all three axes
Included as Standardl Siemens 828D Controller with 15.6 inch touch display l Double arm grab with 24 tool slots
Electrical Connection 400V 3Ph 50Hz Tool Change Time 2 SecTotal Connected Load 48 KVA X axis Travel 760 mmDrive Motor S1 op 25 kW Y axis Travel 440 mmTorque Drive motor S1 32 Nm Z axis Travel 460 mmDrive Motor S6 30% Op 35 Kw Rapid Motion X,Y Z axis 30,000 mm/minTorque Drive Motor S6 39 Nm X axis Motor Torque 6 NmSpindle Taper HSK A-63 DIN 69893 Y axis Motor Torque 6 NmMotor Coolant Pumps 3Pcs 1.27 kW each Z axis Motor Torque 11 NmFlow Rate 66 - 100 l/min Spindle Speeds 24,000 rpmCoolant Tank Cap. 210 Litres Compressed air 5 - 7 barMax . Face Mill Dia. 63 mm Spindle to Table 102 - 562 mmMax. Milling Cutter 32 mm Throat 480 mmRepeat Accuracy ± 0.005 mm Table Length x Width 900 x 410 mmPositioning Accuracy ± 0.005 mm T Slot Size / No. / Dist. 16 mm / 4 / 102 mm Tool Changer Type Double arm grab Max Load Bearing Cap. 350 KgNo.of Tools 24 Dims LxWxH cm 300 x 195 x 231Max Tool dia. adj. free slot Ø80mm Weight 4350 Kg Max Tool Weight 8 Kg
Specification F 150 HSC
Opt. Equipment
Starter Set HSK A-63 0353-6110Air Conditioning 0351-1290401Fourth axis preparation 0351-1290201
Fourth axis complete kit, 100 mm 3 Jaw chuck, Tailstock, Siemens Motor Rotary table 0351-1290210
Fourth & fifth axis preparation 0351-1290202
Fourth & fifth axis complete kit,100 mm 3 Jaw chuck, Tailstock, Siemens Motor 0351-1290250
l Siemens 808D Advanced Controller l Carousel type tool changer with 12 tool slots
Electrical Connection 400V 3Ph 50Hz Max Tool Weight 6 KgTotal Connected Load 15 KVA Tool Change Time 7 SecDrive Motor S1 op 7.5 kW X axis Travel 550 mmTorque Drive motor S1 48 Nm Y axis Travel 305 mmDrive Motor S6 30% Op 11 Kw Z axis Travel 460 mmTorque Drive Motor S6 70 Nm Rapid Motion X,Y Z axis 10,000 mm/minSpindle Taper BT40 X axis Motor Torque 8 NmMotor Coolant Pump 0.65 Kw Y axis Motor Torque 8 NmCoolant Tank Cap. 120 Litres Z axis Motor Torque 11 NmMax . Face Mill Dia. 63 mm Spindle Speeds 10 - 10,000 rpmMax. Milling Cutter 32 mm Compressed air 7 barRepeat Accuracy ± 0.008 mm Spindle to Table 100 - 600 mmPositioning Accuracy ± 0.01mm Table Length x Width 800 x 320 mmTool Changer Type Carousel T Slot Size / No. / Dist. 14 mm / 3 / 100 mmNo.of Tools 12 Max Load Bearing Cap. 300 KgMax Tool dia. adj. free slot Ø63mm Dims LxWxH cm 216 x 186 x 220Max Tool Length 300 mm Weight 2800 Kg
Specification F 105
Optional Equipment
Starter Set BT40 0353-6108Fourth axis complete kit, 125 mm 3 Jaw chuck, Tailstock 0350-1120
Vertical Machining CentreF105 0350-1100
With Siemens 808D Advanced Controller
l Rugged design l Carousel tool changer with 12 tool slots l All linear guides with stainless steel coversl Automatic centralised lubrication l Siemens main spindle motor l Servo drive by SIEMENS on all axes (closed control circuit) l Max. spindle speed up to 10 000 rpm l Machine lamp in the workspacel Portable, electronic handwheel with confirm button and emergency stop mushroom button. Substantially facilitates running in of programs l Integrated coolant unit with 120 litre coolant tank l Tool change occurs automatically or at the push of a button (electropneumatic tool clamping device) l Solid, precision milling table, generously dimensioned with precision surface finish l Access doors very generously designed to reduce cleaning and maintenance times to a minimum l Software package "SINUMERIK 808D on PC" included.
Featuresl Machine with cast base provides rigidity l Carousel tool changer with ten toolsl All linear guides with stainless steel covers l Automatic centralised lubrication l Integrated machine lamp in work spacel Portable, electronic handwheel with confirm button and emergency stop mushroom button. Substantially facilitates running in of programs l Integrated coolant unit with 70 litre coolant tankl Tool change occurs automatically or at the push of a button (electropneumatic tool clamping device)l Solid, precision milling table, generously dimensioned with precision surface finishl Access doors very generously designed to reduce cleaning and maintenance times to a minimuml LED machine lamp for complete illumination of the workspacel Software package "SINUMERIK 808D on PC" included. l Including two years SIEMENS warranty
Electrical Connection 400V 3Ph 50Hz Tool Change Time 7 SecTotal Connected Load 12 KVA X axis Travel 400 mmDrive Motor S1 op 2.2 kW Y axis Travel 225 mmTorque Drive motor S1 14 Nm Z axis Travel 375 mmDrive Motor S6 30% Op 3.2 kW Rapid Motion X,Y Z axis 10,000 mm/minTorque Drive Motor S6 22 Nm X axis Motor Torque 5 NmSpindle Taper BT30 Y axis Motor Torque 5 NmCoolant Pump Motor 650 W Z axis Motor Torque 6 NmCoolant Tank Cap. 70 Litres Spindle Speed Range 50 - 8,000 RpmRepeat Accuracy ± 0.015 mm Compressed Air 7 BarPositioning Accuracy ± 0.015 mm Spindle to Table 75 - 475 mmTool Changer Type Carousel Table Length x Width 800 x 260 mmNo.of Tools 10 T-Slot / Amount / Dist. 16mm/5/50 mmMax Tool Dia. Ø60 mm Max Load Bearing Cap. 150 KgTool Length 200 mm Dims LxWxH cm 193 x 166 x 107Max Tool Weight 6 Kg Weight 1900 Kg
Specification F 80 VMC
Power & Precision
Included as Standardl Siemens 808D Advanced Controller l Carousel Type 10 Station Tool Changer
Included as Standardl Siemens Sinumerik 808D Advanced Controller
l Linear guides on all axes l All axes with ball screws l Servo drive on all axes (X, Y and Z axis)l Tool change at the push of a button (electropneumatic tool clamping device) l Coolant equipmentl Central lubrication l Swivelling control panell Software package "SINUMERIK 808D on PC" included. l Including two years SIEMENS warranty
BT30 Starter Set1 pc. Face milling holder 22mm 1 pc. chuck 2 pc. Weldon 6 mm1 pc. Weldon 8,10,12 & 162 pc. Weldon 20 mm1 pc. adaptor BT 30 x 2MT3 pcs. Collet chuck holder ER321 pc. spring collet spanner ER 3218-part spring collet set ER 321 pc. Tool height adjuster1 pc. assembly and tool adjustment gauge14 pcs. pull studs1 pc. taper squeegee
0353-6107Electrical Connection 400V 3Ph 50Hz Rapid Motion X,Y Z axis 8,000 mm/minTotal Connected Load 3.125 KVA X axis Motor Torque 2.4 NmDrive Motor S1 op 1.5 kW Y axis Motor Torque 2.4 NmTorque Drive motor S1 10 Nm Z axis Motor Torque 2.4 NmSpindle Taper BT30 Spindle Speed Range 90 - 4,000 rpmCoolant Pump Motor 95W Compressed Air 8 BarCoolant Tank Cap. 25 Litres Spindle to Table 20 - 300 mmRepeat Accuracy ± 0.025 mm Table Length x Width 620 x 180 mmPositioning Accuracy ± 0.025 mm T-Slot / Amount / Dist. 12mm/3/50mmX axis Travel 355 mm Max Load Bearing Cap. 30 KgY axis Travel 190 mm Dims LxWxH cm 160 x 145 x 201Z axis Travel 245 mm Weight 1400 Kg
