Verylube-catalogue-2013-En_web.pdf

8/20/2019 Verylube-catalogue-2013-En_web.pdf

1/40

Catalogue of productsVERYLUBE

© XADO Chemical Group

Metal conditioners

Products for engine.Oil system

Fuel system

Other products

Car body products

Compartment care products

Glass care products

Lubricants

Products for locks

Firearms care products


2/40

More than 100 items are manufactured under VERYLUBEtrademark. These products have already become popularin more than 35 countries.

Products include fuel and oil additives, highly efficientcleaners, car care products for units, joints, compartment,glass etc.

Whatever part you name in your car, VERYLUBE willsurely offer the product for it!

Dear Customer!

Thank you for your interest in products of VERYLUBEtrademark. The VERYLUBE trademark is a propertyof XADO Chemical Group. VERYLUBE is a high qualityseries of products with a following MOTTO:

«High quality product atan affordable price!»

The present catalogue will help you to get acquainted with a wide range of VERYLUBE

products and choose exactly what you need for your car.


3/40

| 3

Anticarbon

Product designed to clean piston rings from carbon.

Fast-acting product designed to clean stuck piston rings of gasoline and diesel engines from carbon. It removes all

scale and tar contaminations from the parts surfaces of cylinder-piston group. It does not require oil change after

application.

Advantages

• Restores mobility of stuck piston rings.

• Decreases oil consumption.

• Cleans cylinders and pistons, combustion chambers,and valves from all types of contaminations (scale,

carbon, varnish and tar).

• Restores compression in cylinders.

• Decreases noise of engine operation.

• Removes deposits from spark plugs (glow plugs).

• Decreases the level of harmful exhausts into theatmosphere.

Application instructions

1. Warm up the engine. The engine should be warm but

not hot.

2. Unscrew the plugs (burners). Disconnect the wire of

the ignition timing sensor, Hall sensor or commutator.

3. Spray the substance (up to 5 seconds) through a

nozzle hose (or introduce the content of 1 tube) into

each cylinder. Screw the plugs back. Wait for 10–20

minutes. Unscrew the plugs. Cover the plugholes with absorbing fabric to avoid dirt ying out and

getting onto the paint. Rotate the engine with the

starter for several seconds.

4. Reinstall spark plugs.

5. Start the engine and run it at moderate RPM for up

to 15 minutes. During this time, the residues of the

softened carbon will be removed through the exhaust

system.

Dosage

1 tube — 1 cylinder.

One aerosol can is enough to clean rings from carbonin 20 cylinders.

10 mlArt. XB 42051tube

10 mlArt. XB 42151

tube in blister

320 mlArt. XB 40011aerosol can

Note

Avoid getting the substance onto paint.

Safe for catalytic converters, oxygen sensors, mechanical rubber

goods and sealers.

The VERYLUBE ANTICARBON in tubes can be used for engine oil

system ushing:

1. Introduce ANTICARBON into warmed up engine through the oil

ller neck at a ratio 40 ml of ANTICARBON for 3–5 liters of oil.

2. Let the engine idle for 10–15 minutes.

3. Change oil and oil lter.

Products for engine.Oil system.


4/40

Products for engine. Oil system4 |

Absolut & Absolut+

Flush for engine oil system.

Quickly and safely cleans engine oil system from all types of contaminations including hard-to-remove varnish (yellowcolor). The dissolved contaminations are kept in suspension state and then removed with the used oil.

Advantages

• Cleans engine oil system up to potential cleannesslevel.

• Cleans cylinder-piston group and restores pistonrings mobility.

• Eliminates knocking and normalizes hydraulic valvelifters operation.

• Improves turbo performance of the engine.

• VERYLUBE ABSOLUT+ cleans piston rings formcarbon more effectively.

Verylube Absolut

It is recommended to use Verylube Absolut with each

oil change or when adding different oil type.

1. Introduce the ush through the oil ller neck in warmed

up engine before oil change.

2. Let the engine idle for 10–20 minutes. Do not drive a car!


Dosage250 ml (1 can) for 5 L of oil.


Verylube Absolut+

It is recommended to use Verylube Absolut+ for intensive

cleaning of engine oil system before oil change. It is

especially effective for restoring of the piston rings, which

became stuck due to the short-term engine overheating.

If moderate clogging (including vanish deposits

removal or carbon removal from the piston rings).

1. Introduce the ush through the oil ller neck of the

warmed up engine.

2. Drive 75–100 km as usual.


If signicant clogging (heavy deposits under valve

cover, black sludge on the oil gage).

1. Introduce the ush through the oil ller neck of warmed

up engine.

2. Let the engine idle for 3–5 minutes. Do not drive a car!


Dosage300 ml (1 can) for 5 L of oil

250 mlArt. XB 40159сan

Absolut

300 mlArt. XB 40164сan

Absolut +


5/40

| 5

Flushing oil

Mineral low-viscosity oil with a complex of special additives for engine and transmission ushing.

Contains revitalizant.

It is designed to clean oil systems of engine and transmission. Special detergent-dispersant, anti-wear and extreme

pressure additives allow safe ushing of oil system (for 30–40 minutes) and its efcient cleaning from all types of

contaminations (up to potential purity). ХАDО revitalizant creates protective reserve against wear during ushing.

Advantages

• Absolutely safe ush of oil system up to the potentialpurity (VitaFlush technology).

• Protective reserve against wear (revitalizationtechnology).

• Possibility of intensive ushing of very contaminatedassemblies (up to 30–40 min) with anti-wear additives.

• Restoration mobility and compression of the oil rings.

• Elimination of the hydraulic compensators lock.


For engines:

1. Drain warm used oil.

2. Pour the ushing oil up to the minimum point on a

probe.

3. Start the engine and let it idle for 10–15 minutes

(if the engine is signicantly clogged — for 30–40

minutes).

4. Stop the engine, pour out the ushing oil, and

replace oil lter.

5. Pour fresh oil.

For transmission assemblies:

1. Drain warm used oil.

2. Pour the ushing oil into the transmission assembly

up to the nominal level.

3. Let the assembly work without any load (with put up

wheels) for 10–15 minutes, and up to 30–40 minutes —

in case of severe clogging.

4.Turn off the engine and drain ushing oil.

5. Pour fresh oil for transmission.

Attention!

Do not drive with the ushing oil in the system!

200 LArt. XB 20550

2 LArt. XB 20250

20 LArt. XB 28750

60 LArt. XB 20450

Package: 2 L — packet; 20 L — сan;

60 и 200 L — barrel


6/40


7/40

| 7

Aquastop

Water and ice remover from gasoline.

Fast-acting product designed to remove moisture from fuel system. It breaks up water drops and ice crystals, distributing

them evenly throughout the whole volume of fuel. As a result, moisture is removed together with exhaust gases during

the process of fuel combustion. It keeps fuel system parts in ideal condition and protects them from corrosion. It is

recommended for regular use.

Advantages

• Quickly and efciently removes water from the fuel

system due to emulsication of moisture in gasoline.

• Prevents water condensation in a fuel tank.

• Protects fuel system from corrosion.


To remove moisture and ice from fuel system of

gasoline engines.1. Introduce Verylube Aquastop through the neck of

a fuel tank, at a ratio 10 ml (1 tube) for 5 liters of

gasoline.

2. Run the car as usual.

As a preventive measure (before winter season and

each time at sharp temperature drop).

Add Verylube Aquastop to the fuel tank at a ratio 10 ml

(1 tube) for 20 liters of gasoline at each fueling.

Expert's Advice

For convenient application, squeeze the contents of the

tube into the refueling nozzle before fueling.

Note

To defrost door locks of a car: squeeze a small amount of Verylube

Aquastop into the keyhole. The lock will be defrosted in a minute.

10 mlArt. XB 42056

tube

10 mlArt. XB 42156

tube blister


8/40

Fuel system8 |

Diesel-Lux

Complex product designed to improve properties of diesel fuel and ush the engine fuel system.

Quickly cleans the fuel system from all types of sediments and contaminations. It protects injector valves from burningand clogging up with tarry sediments. The Diesel-lux Winter (for winter season) signicantly depresses the chilling

temperature of diesel fuel and prevents formation of parafn crystals.

Advantages

• Cleans the fuel system fromcarbon, tarry and varnish

deposits; protects it from wear

and corrosion.

• Increases cetane rating.

• Improves fuel combustion.

• Protects high pressure fuel pumpfrom wear and corrosion.

• Reduces fuel consumption.• Decreases toxic exhausts.

• Removes moisture from fuel.


Squeeze out the contents of the tube

into a fuel tank before refueling.

Expert's Advice

To make the application easy, squeezethe contents of the tube into the refueling

nozzle before fueling.

Note

Compatible with all types of fuel.

VERYLUBE Diesel-lux Winter is introduced when

warmed up to the temperature of +20...25 °С into

non-thickened (transparent) diesel fuel.

Diesel-luxSummer

10 mlArt. XB 42053

tube

10 mlArt. XB 42153tube blister

Diesel-lux

Winter



Dosage

Diesel-lux Summer

Preventive dosage

(with every fueling)

1 tube for 50 l of fuel

Repair dosage

(once)1 tube for 20 l of fuel

Diesel-lux Winter

For 50 liters of fuel.

Ambient airtemperature, °С

Tubes,pcs

0… - 20 1

- 20… -30 2

-30… -40 3


9/40

| 9

Advantages

• Efciently decreases the freezing temperatureof diesel fuel.

• Economical in use, at a ratio 1:10 000.

• Prevents clots and parafn crystals formation.

• Protects lter from plugging when pumpingcold fuel.

• Guarantees easy engine start at low temperature.


1. Squeeze the contents of the tube into a fuel tank(refueling nozzle).

2. Fuel a car following the dosage instructions.

3. Run the car as usual.

Dosage

Up to –20 °С — 1 tube for 100 liters of diesel fuel.

Up to –35 °С — 1 tube for 20 liters of diesel fuel.

Expert's Advice

To make the application easy, squeeze the contents

of the tube into the refueling nozzle before fueling.

Note

VERYLUBE Antigel should be introduced into the non-thickened

(transparent) diesel fuel.

The substance should be warmed up to the temperature of +20...+25 °С

before application.

Antigel

Superconcentrate for diesel fuel.

Special super concentrated product designed to improve the low-temperature properties of diesel fuel. It is used toimprove the uidity and pumpability of fuel at low temperatures.




10/40

Fuel system10 |

Carburetor and injector cleaner

Universal carburetor cleaner.

Product designed for quick and efcient cleaning of carburetors, injector gate as well as air and fuel lines. Easily

removes all types of contaminations (varnish, oil and gasoline lms, scales, sediments and dust) from the fuel system

of a car.

Advantages

• Cleans carburetor parts (choke, oat chamber, jetsand canals) thus restoring their initial performances.

• Restores mobility of the injector choke.

• Removes contaminations from the air introductionmanifold and fuel system.

• Increases engine power and acceleration.

• Reduces harmful exhausts into the atmosphere.

• Decreases fuel consumption.

• Safe for catalytic converters and oxygen sensors.


To clean a carburetor.

1.Take off air lter.

2. Start the engine.

3. Shake the can.

4. Spray liberally onto all visible

carburetor parts. While cleaning

keep up increased engine rpm

with a choker level.

To clean an injector (gate and

air line).

1. Shake the can.

2. Spray the Cleaner onto the

choker (into the air inlet) while

the engine is warm and not

working.

3. Start the engine; keep up

increased engine rpm with a

choker level for 3–5 minutes.

For complex cleaning (fuel

tank, pipelines, jets, inlet

valves, spark plugs and

combustion chambers).

Before fueling, spray the Cleaner

into the ller neck of the fuel tank

(for 10–15 sec per 20 liters of

fuel).




11/40

| 11

Cleaner of throttle buttery and EGR valve

Efcient product designed to clean throttle buttery of injector, valve of exhaust gas

recirculation system (EGR) and carburetor.

Advantages

• Quickly softens and removes all kinds of contamination.

• Restores operating parameters of the mechanism to thenominal ones.

• Contributes to engine power increase and its acceleration.

• Reduces content of harmful exhaust gases into theatmosphere and decreases fuel consumption.


Quick Start

Product designed for quick engine start.

Efcient product designed for easy and quick starting of engines of all types: gasoline

(carburetor and injector ones), diesel, four- and two-stroke ones, as well as rotary engines.

It is perfect help in winter season.


Advantages

• Makes engine starting exceptionally easy at high humidity, wetspark plugs, weak accumulator and low grade fuel.

• Reduces start-up wear of engines.

• Economical in application.


To start a gasoline engine.

1. Shake the can.

2. Spray Quick Start (for 2–3 seconds)

into the air lter or the inlet air manifold.

To start a diesel engine.

1. Shake the can.

2. Spray Quick Start (for 2–3 seconds) into

an inlet manifold when plugs are off and

gate is open.


To clean a throttle buttery.

Spray a large amount of the product onto a throttle

buttery (into induction manifold of air supply) on a

warmed-up non-running engine. Operate the engine at

high rpm for 3-5 min.

To clean a EGR valve.

Take off the valve. Spray a large amount of the product

onto contaminated surface. Clean dry in 1-2 min. If

necessary, repeat the treatment.

To clean a carburetor.

Take off an air lter. Start the

engine. Spray a large amount

of the product onto all visible

parts of the carburetor. During

cleaning, maintain increased

engine rpm with a lever of the

throttle buttery.


12/40

12 |

Engine compartment cleaner

Product designed to clean the external parts of an engine and other car

assemblies.

Immediately removes oil spots, dust and grime. After using the cleaner, parts look as new.

Can be used to clean transmission, car suspension and steering assemblies.

Advantages

• Effectively cleans underunderhood space from

oil, varnish, tar and other

contaminations.

• Restores original look ofparts.

• Acts immediately.


1. Switch off the ignition.

2. Shake the can.

3. Spray onto the surface of the engine (assembly,

part) to be cleaned.

4. Let it trickle down together with dirt and wash

with water.

5. Repeat the procedure in case of severe

contaminations.

Other products



Belt reconditioner

Spray designed to take care of driving belts of engine assemblies.

The product is designed to take care of V-belts and multiple V-belts of the pump drives

of the wheel booster, generator, air conditioner etc. Effectively cleans surfaces from

contaminations and restores elasticity of the belts. Protects from cracking and eliminates

slipping.

Advantages

• Cleans the work surface of belts fromcontaminations and oiling; removes

slipping.

• Restores the structure of belt materialand tightens it. Prolongs the service

life of belts and reduces wear.

• Prevents belts from drying and

cracking.


1. Shake the can.

2. Spray onto the work (V-) surface

of a belt.


Note

Does not require rubbing.

Expert's Advice

It is better to clean a cold or slightly warm engine. A high temperature of the engine

provokes fast evaporating of the cleaner and cleaning efciency can be decreased.

Note

Safe for lacquer coating of all types, glass, plastic, rubber and

chrome-plated parts.

Does not contain acid, alkali and other corrosion-hazardous

substances.


13/40

| 13

Stop Leak liquid radiator sealer

The sealer is designed to prevent leaks in the engine cooling system.

It is the latest generation product for sealing the cooling system leaks. Completely eliminates leaks, permanently and

reliably seals hair cracks and minor damages up to 0.9 mm in the pipelines and joints. Eliminates loose t of the pump

gasket, leakage of cylinder block gaskets etc.

Advantages

• Eliminates the need for expensive repair.

• Universal application for gasoline and dieselengines of cars and other equipment.

• Compatible with all types of uids applied tocooling systems.

• Safe for cooling system parts (gaskets, rubberhoses, aluminum, plastic and steel radiators).

• Lubricates the pump gasket.

• Protects the cooling system against rust andcorrosion.


1. Shake well before use!

2. Warm the engine up to the working temperature, the

engine should be warm but not hot.

3. Add Verylube Stop Leak into the radiator tank when

the engine is not running.

4. Start the engine and let it idle for 5-10 min with the

heating switched on.

250 mlArt. XB 50010can

Attention!

The antifreeze in the cooling system is under pressure

when the engine is hot. Be careful when opening the

radiator/cooling system: hot coolant or steam might

escape from the system.

To avoid eventual leaks in the cooling system, use the

sealer right after changing the antifreeze.

Dosage

The can (250 ml) is designed for cooling system capacity up

to 12 L.


14/40

Car body products

Plasticor

Antigravel

Plastic corrosion-preventive coating for surface of non-painted fender ares

and car bottom.

Rust preventive product designed to treat fender wells before assembling plastic

protection. Used for overall and local protection of a car body and strengthens existent

coating.

Antigravel rubber coating of light-grey color which allows further painting.

Used for painted surfaces of a car body (lower sections of doors etc.), which are exposed

to road dust and gravel hits. Can be applied to metal, lacquered surfaces and plastics.

Advantages

• Has a high anticorrosion resistance tochemical activity (weak acids, alkali

etc.).

• Protects car body from stone hitting,decreases noise and vibration.

• Forms a thick volumetric coating withthixotropic properties.

Advantages• Forms an elastic lm which is

particularly resistant to stone

hitting.

• Permits further painting.

• Decreases noise and vibration.

• Safely protects from corrosionand chemical activity (road salt).


1. Remove dirt, rust, and dust from the

surfaces to be covered.

2. Shake the can.

3. Spray onto the surface at a distance

of 20–30 cm.4. Apply 2–3 layers on the surfaces to

be coated. Each next layer should be

applied after short-term waiting.

5. Wait 1–2 hours. Run your car or

assemble plastic wings.

Application instructions1. Remove dirt, rust and dust from the

surfaces to be covered with Antigravel.

2. Shake the can.

3. Spray onto the surface at a distance of

20–30 cm.

4. Apply 2–3 layers on the surfaces to be

coated. Each next layer should be applied

after short-term waiting.

5. Wait 30–60 minutes. Run your car.


500 mlArt. XB 40126

aerosol can

Note

The ambient air temperature while treating should be +15…20 °С.

Excess of Plasticor can be easily removed with VERYLUBE Tar Stain Remover.

Keeps high state stability (does not trickle down).

Stable to temperatures up to +85 °С

Note

The ambient air temperature while treating

should be +15…20 °С.

Excess of Antigravel can be easily removed

with Verylube Tar Stain Remover.

14 |


15/40

| 15

Anticor ML

Wax anticorrosion coating for closed car body areas.

High performance rust preventive product designed to protect internal surfaces of hollow parts of a car body: doorhollows, spars, fenders etc. Specially composed for anti-corrosive treatment of a car body based on the Swedish ML

method (spreading, preserving and "sealing up").

Can be applied on metal and lacquer coating surfaces. Spreads well and penetrates into the smallest cavities which

require protection, such as weld seams and cracks.

Advantages

• Forms a very thin protective lm (from 40 micron) withstrong adhesion.

• Removes moisture.

• Seals up centers of corrosion attacks.

• Has an increased anticorrosion resistance to chemicalactivity (weak acids, alkali etc.).

• Keeps up the form, does not trickle down from verticalsurfaces.

• Stable to the temperature up to +160 °С.

• Low consumption (500 ml can for 20 m²).


1. Clean the open surfaces of the parts from dirt, rust

and dust.

2. Shake the can.

3. Spray onto the surface at a distance of 20–30 cm.4. VERYLUBE Anticor ML should be applied in one

layer.

5. Use an extension pipe to treat close surfaces.

Note

The ambient air temperature while treating should be +15…20 °С.

Can be used in the engine compartment.

Excess of Anticor ML can be easily removed with Verylube Tar Stain

Remover.



16/40


17/40

| 17

Wheel disc purier(for aluminum)

Product designed to clean wheel discs.

Easily cleans wheel discs from contaminations and adds luster to them. Protects from

corrosion. Applied for cleaning any type of wheel disc, including those made of light

aluminum alloys.

Wheel disc purier (for chromium)

Advantages

• Quickly cleans discs from hard-to-remove contaminations, causedby break operation.

• Adds luster to wheel discs.

• Creates a dirt-repellant and anti-corrosion protective lm.


Spray onto the surface of the cold

wheel disc, wash with large amount of

water in 10-15 sec. After cleaning, it is

recommended to treat the cover with

VERYLUBE Conditioner of rubber and

plastic.

Attention!

Please check the effect of the product

on a small part of the disc before

application. Do not apply to units of brake

system, steering system and mounting.

It is not recommended to apply the

product to chromium-plated wheel discs.

In this case use Wheel disc purier (for

chromium).

500 mlArt. XB 40134bottle with

trigger

Product designed to clean chromium-plated wheel discs.

Easily cleans wheel discs from contaminations and adds luster to them. Protects from

corrosion. Applied for cleaning chromium-plated wheel discs.

Advantages• Quickly cleans discs from hard-to-remove contaminations,

caused by break operation.

• Adds luster to wheel discs.

• Creates a dirt-repellant and anti-corrosion protective lm.


Spray onto the surface of the cold wheel disc, wash with largeamount of water in 2-3 min.

500 mlArt. XB 40108

bottle withtrigger


18/40

Car body products18 |

Lacquer coating polish

Product designed to take care of lacquer coating of a car.

Effective product for cleaning and polishing lacquer coatings of a car. It is applied

universally for glossy lacquer coatings and metallized enamel (metallic lacquer), as well

as for new and faded surfaces.

Advantages

• Refreshes and gives deep shine tolacquer coating. Smoothes out minor

surface irregularities.• Preserves lacquer coating and

provides long-term protection from

environmental impact.



1. Shake the can.

2. Spray a small amount of the product

onto the clean dry surface.

3. Polish with a cloth.

Chrome conditioner

Spray designed to take care of decorative chrome-plated surfaces.

Today's best special product for cleaning and polishing chrome-plated surfaces. Gives a

new appearance to chrome-plated parts of cars, motorcycles and other vehicles.

Advantages

• Removes a dull layer, darkspots and corrosion.

• Refreshes and gives shining tochrome-plated parts.

• Provides a long-term protectionfrom oxidation.

320 mlArt. XB 40022

aerosol can


1. Shake the can.


onto the surface of the part to be

treated.



19/40

| 19

Metal polish

Conditioner for rubber and plastic

Product designed to take care of exterior metal parts of a car body.

Today's best product for cleaning and polishing metal parts of the car body. It is applied

universally for steel and aluminum load bearing elements, as well as for parts made of

copper alloys and zinc.

Spray conditioner designed to take care of rubber and plastic articles.

Product designed to restore the original color of rubber and plastic parts.

It is used to treat tires, bumpers, moldings, mirrors, dashboard and other rubber and

plastic parts of cars. It is an effective alternative for washing the underhood space of

an engine. After application parts look as new as if they have just been taken off from

the conveyer.

Advantages

• Gives a bright metal shine to fadedsurfaces and refreshes them.

• Eliminates small surfacesimperfections.

• Protects from environmental attack.

Advantages

• Cleans micro cracks andscratches from dirt and lls

them in.

• Gives original color andshine to rubber and plastics

parts.

• Protects them from fadingand cracking.


320 mlArt. XB 40006

aerosol can

500 mlArt. XB 40106

aerosol can


1. Shake the can.


onto the surface to be treated.



1. Shake the can.

2. Spray a thin layer onto the surface to

be treated.

3. Wipe off with a cloth.

Note

Surfaces do not

require polishing after

treatment.


20/40

Compartment care products20 |

Dashboard polish

Product designed to take care of plastic and wooden parts of a car compartment.

Efcient product designed to clean and refresh parts in a car compartment (control panel and other plastics, wooden,

leather and vinyl parts). Efciently cleans the surfaces from contaminations and protects from cracking.

Advantages

• Easily penetrates into the smallest scratches on thesurface of parts and removes dirt.

• Refreshes the appearance of plastics and wood andmakes them shine.

• Gives antistatic properties to the surface, thus, it getsless dirty and dusty.

• Does not leave any greasy lm after use.

• Prevents plastics from cracking and prevents its fadingin the sun.


1. Shake the can.

2. Spray a small amount of the product onto the surface

to be cleaned.


Note

Does not require lots of polishing.

Expert's Advice

If with time the shine is gone, wipe again the dashboard

with cloth (without the polisher). The shine will appear

again. with scent

cherry

320 mlArt. XB 40020

aerosol can

500 ml

Art. XB 40120aerosol can

with scentlemon


500 ml

Art. XB 40110aerosol can


21/40

| 21

Compartment cleaner

Leather care

Compartment upholstery cleaner.

Effective and handy product designed for cleaning car compartment upholstery (natural

and articial fabric, carpeting, plastic, etc). Easily cleans oil spots.

Safe and effective care of leather in a car compartment.

Product designed to take care of natural and articial leather upholstery (seats, doors,

panels etc). Contains castor oil.

Advantages

• Easily cleans the upholstery andremoves oil and grease contaminations.

• Removes grime.

• Restores original appearance, colorand texture of fabric. Bristles up and

straightens bers; gives silky look to

upholstery.

• Absorbs unpleasant smells.

• Gives antistatic properties to upholstery.

Advantages

• Quickly penetrates intoleather structure and removes

contaminations.

• Restores leather elasticity.

• Covers small cracks and gives shineto the nish.

• Gives antistatic properties to thesurface; thus it gets less dusty.

• Gives waterproof and stain repellantproperties to the leather.

•Prevents leather ageing and fading in

the sun.


1. Shake the can.

2. Spray a small amount onto a

sponge.

3. Clean the spots on the

upholstery with formed foam.


1. Shake the can.

2. Spray a small amount of this product

onto the leather surface.


Note

Do not use for cleaning

leather articles.

Expert's Advice

For more effective grime removal,

use a clothes brush.


320 mlglossy

Art. XB 40012

mattArt. XB 40032

aerosol can

150 mlglossy

Art. XB 40112

mattArt. XB 40132

aerosol can


22/40

Compartment care products22 |

Complex foam cleaner for car airconditioners

Product designed to clean and maintain car air conditioners.

It is used for in-place cleaning of air-ways of complicated conguration in the modern

automobile air conditioners. It removes contaminations quickly and easily and provides inow

of fresh air. It has disinfectant properties. It kills fungi and bacteria, thus preventing the risk of

allergies and other respiratory diseases.

Advantages

• Cleans the air conditionerfrom contaminations and

provides an inow of cleanand pure air from the air

conditioner.

• Disinfects the airconditioning system,

eliminates musty odors, kills

fungi and bacteria.

• Forms a bactericide lmon the air conditioner

evaporator and airways.


1. Shake the can.

2. Spray the content into a deector (airway) for cold airof an air conditioner using tube extender, so that the

substance could get onto evaporator.

3. Start the engine in 15–30 minutes and let it idle for 3–4

minutes with an air conditioner fan turned on.

Note

Spray the substance in a well ventilated area or outside when the

engine is turned off and the car doors are open. Contains biologically

active substances.320 mlArt. XB 40016aerosol can

Antibacterial cleaner for carventilation systems

Product designed for antibacterial treatment of car ventilation- and air deodorization

systems.

It is used for ventilation- and air conditioning systems of any type (heating/ventilation,

conditioner, climate control etc.). Prevents the risk of allergies and other respiratory diseases.

Cleans and disinfects systems. Deodorizes air.

Advantages

• Kills fungi and bacteria,eliminates musty odors.

• Deodorizes air.


1. Shake the can.

2. Spray the cleaner for 3-4 seconds into all airways of air

conditioning system (ventilation) of a car.

3. Start the engine in 2–3 minutes and let it idle for 2–3

minutes with an air ventilation system turned on.

Note

Spray the substance when the engine is not operating.

Contains biologically active substances.

As preventive measures, use the product not less than once a month.

320 mlArt. XB 40616

aerosol can


23/40

| 23Metal conditioner

Verylube Turbo

Metal conditioner for engine.

A completely synthetic concentrated multicomponent product, composed on the basis of the latest discoveries in tribology

and chemistry. It is formulated specially for internal combustion engines. It is used for complex protection of friction parts

of gasoline and diesel engines, including turbo-charged.

Advantages

• Increases engine power.

• Increases compression.• Reduces noise and vibration.

• Decreases oil consumption.

• Improves dynamic characteristics of a vehicle.

• Decreases fuel consumption.

• Improves motor oil properties.

• Protects engine parts from wear.

• Makes cold start easy.

• Reduces harmful exhausts.


1. Pour the conditioner into warmed up engine through

the oil ller neck.

2. Let the engine idle for 3 minutes.

3. The conditioner works during the whole service life of

the oil.

Dosage

125 ml (1 can) for 4 liters of oil.

Technical characteristic

The formula of VERYLUBE TURBO contains carbon

С60 molecules (fullerenes) and aliphatic hydrocarbons

reinforced with halogens.

Note

Optimal concentration: 3% of the oil volume. Overdose up to 50% is

allowed, i.e. up to 4.5% of the oil volume.

The conditioner has gentle detergent properties that remove carbon from

piston rings.

To achieve the maximum effect — use regularly with every oil change.

125 mlArt. XB 40060can


24/40

Metal conditioner24 |

Metal conditioner

Multilevel protective formula against wear and overloads of the automobile units.

The product is designed for creation of special conditions for operation of engine units (transmission, hydraulicsystem) due to which an effective multilevel system of wear and overload protection will be formed.

The metal conditioners are formulated on the base of a fully synthetic polyhydric polymer and a well-balanced

package of antioxidant and antiscoring additives. The polymer molecules are highly resistant to destructive impact of

local overloads in the friction zone due to covalent interatomic bonds which allow eliminating metal-to-metal contact in

the friction zone within the entire lifespan of the oil.

Advantages

• Protects against wear and overloads

• Increases engine power and driving

moment• Increases service life of subassemblies

• Reduces noise and vibration

• Reduces the amount of exhaustemissions

Metal conditioner for hydraulic system

1. Shake the can.

2. Spray the product through the tube-nozzle into the

oil ller neck (vent of the oil gage rod) of automatic

transmission or mechanism of the power steering

booster.

3. Drive the car in normal mode without any restrictions.

Nominal dosage125 ml (1 can) for 8 L of hydraulic uid.

20ml (spray during 15-20 seconds) for 1 L of iud.

Metal conditioner for transmission

1. Shake the can.

2. Spray the product through the tube-nozzle into the

oil ller neck (oil measuring hole) of mechanical

transmission, axle gearboxes or transfer cases.

3. Drive the car in normal mode without any restrictions.

Nominal dosage

125 ml (1 can) for 2 L of transmission oil.75 ml (spray during 1 minute) for 1 L of oil.

150 mlArt. XB 40261

aerosol can

Forengine

150 mlArt. XB 40262

aerosol can

Fortransmission

150 mlArt. XB 40264

aerosol can

For hydraulicsystem

Application

Metal conditioner for engine

1. Pour the product into the oil ller neck of

the warmed up engine at the rate of 3-6%

from the oil system nominal value.

2. Provide the engine operation in idle mode

during 3 minutes.

3. Drive the car in normal mode without any

restrictions. The resource of metal conditioner is enough

for the whole period of oil exploitation.

Nominal dosage

125ml (one bottle) for 4 L of oil.

24 |


25/40

Insect trace remover

Concentrate for intensive windshields cleaning.

Easily and quickly cleans glass, metal, paint, plastic, as well as nickel- and chrome-plated parts

of a car. Specially designed to remove organic contaminations which contain chitin.

Advantages

• Removes insect traces.

• Dissolves fresh and oldspots of wood resin and tar.

Removes traces of poplar budsand sap of plants.

• Removes lime spots.

• Easily cleans windshieldsfrom contaminations (road

dirt, oil coating, etc.) owing to

improved detergent properties.

Applicationinstructions

VERYLUBE Insect trace

remover (aerosol).

1. Shake the can.

2. Spray onto the surface to

be cleaned.

3. Wipe off with a cloth

(sponge) in 5–10

seconds.

VERYLUBE Insect trace

remover (sachet).

Add the contents of a sachet

into a windshield washer

reservoir at a ratio 1 sachet

for 3 liters of uid.

Note

If strongly

contaminated, the

dosage should be

doubled.

320 mlArt. XB 40004

aerosol can

500 mlArt. XB 40404bottle withtrigger

20 mlArt. XB 40104packet

Red Penguin

250 mlArt. XB 50006two-chamberplastic bottle

Concentrate for intensive windshields cleaning.

Thanks to improved detergent properties, it easily cleans windshields from insect traces

and other contaminations (road dirt, oil coating, poplar buds etc.).

Advantages

• Quickly removesinsect traces and other

contaminations.

• Concentrate product,economic and handy in

application.


Open the cover. Fill the dozer with the uid,

squeezing smoothly the main bottle. Pour the uid

into the windshield washer reservoir (mix it with

water).

Dosage:

25 ml of the uid for 3 L of water.

| 25Glass care products


26/40

Glass care products26 |

Antirain

Spray designed to improve water-resistant properties of windshields surfaces.

Creates a thin hydrophobic lm on the glass. After treatment the water drops do not

spread on the glass, but quickly run down improving visibility. Increases signicantly the

glass limiting wetting angle.

Advantages

• Improves visibility during rainor sleet.

• Prevents freezing of windshields.

• Indispensable if windshield wipers are out of order.


1. The treatment should be made in dry weather.

2. Shake the can.

3. Spray Antirain onto the clean dry external

surface of the windshield, mirrors and lights.

4. Polish glass with a cloth.

320 mlArt. XB 40027

aerosol can

Note

Recommended for regular use (once

per 3–4 weeks).

Ice-breaker

Frost remover and lock defroster.

It is used to remove frost from the windshields. It also quickly removes ice from

mirrors, paint, chrome-plated, plastic, and rubber parts. Efciently defrosts door

locks.

Advantages

• Quickly defrosts and efcientlyremoves ice from car windows.

• Thaws out ice-covered car

surfaces and locks.• Removes ice and frozen rough

layer of snow from mirrors,

paint, chrome-plated, plastic and

rubber parts.


VERYLUBE Ice-breaker (aerosol)

To remove ice.

1. Shake the aerosol can.2. Spray onto the frozen surface, wait

10–15 seconds, and remove the

thawed ice with a scraper or a sponge.


550 mlArt. XB 40063bottle withtrigger


To defrost door locks.

1. Shake the aerosol can.

2. Spray into the keyhole. The lock will

be defrosted in 1 minute.

VERYLUBE Ice-breaker (tube)

Squeeze the contents of the tube into

the keyhole. The lock will be defrosted in

1 minute.


27/40

| 27

Antifog

Spray designed to prevent steaming up on windshields.

This efcient product prevents moisture condensation on the internal surfaces of

windshields. Allows avoiding the undesirable effect of window steaming in chilly and

rainy weather.

Advantages

• Prevents water condensation on windshields.

• Does not let moisture gather into tiny

drops keeping windshields clean andtransparent.


1. Shake the can.

2. Spray Antifog onto the glass surfaces.

3. Wipe the glass with a cloth.


Note

Can be applied to a steamed up window.

Recommended for regular use (once per 3–4

weeks).

Auto Shampoo

Concentrate for intensive car cleaning.

Thanks to complex formula of surface-active substances (tensides), it easily and absolutely

safely washes off all kinds of contamination from a car body.

Advantages

• Quickly dissolves dirt on thecar body surface.

• Can be used for cleaningpain surfaces of all types.

• Does not leave stains.

• Safe for rubber and plastic.

• Handy application.


Open the cover.

Fill the dozer with the shampoo,

squeezing smoothly the bottle.

Add it into water and make foam

Dosage:

25 ml of shampoo for 5 L of water.

250 mlArt. XB 50007two-chamberplastic bottle


28/40


1. Shake the can.

2. Spray onto the treated surface from the distance of10–20 cm.

3. Use the nozzle for hard-to-reach places.

Lubricants

Any Way

Universal penetrating spray lubricant for different mechanisms. Contains revitalizant.

It is designed for all types of units and mechanisms, weapons, tools and equipment. AnyWay lubricant restores mobility

of units and parts; it can penetrate easily and quickly into the rusted or jammed joints, lubricates and separates them.

This lubricant efciently protects contact places from corrosion. It is neutral to rubber, wood, plastics, lacquer coating

and bluing. All-purpose helper!

Advantages

• Lubricates assembly parts and restores friction surfacesusing unique XADO technology.

• Protects from rust and corrosion under conditions of

increased humidity, contamination and action of hostileenvironment (saline, acid solution and alkali).

• Displaces moisture and dries the contacts of electricequipment.

• Serious barrier for water and moisture.

• Prevents electrical leaks and shorts.

• Defrosts door locks and restores their mobility, protectsthem from freezing and corrosion.

• Cleans off contamination, easily dissolves grease andtar spots; removes glue residues, insect traces and

prevents adhering of dirt and dust.

• Takes care of weapon parts and gently removes the gunpowder scale.

• Preserves parts and protects them from corrosion andoxidation.

150 mlArt. XB 40001аerosol can



28 |


29/40

Universal penetrating lubricantUniversal penetrating spray-lubricant. “Liquid key”.

The lubricant penetrates easily and quickly into threaded and other joints, returns

mobility to rusted parts. It is recommended for application at service stations, garages,

shops, in household and industrial environments. It can lubricate any friction surface of

the parts.

Advantages

• Removes oil and grease contaminations from car bodysurfaces.

• Protects parts from corrosion and oxidation.

• Defrosts door locks and prevents their freezing.

• Displaces moisture and eases the engine start in damp weather.


1. Shake the can.

2. Spray a thin layer onto a work surface

(part, joint).

| 29


1. Shake the can.

2. Spray the contents onto the clean surface of the

part (joint).

Any Way

Consistent lubricant with penetrating effect and the revitalizant.

It is designed for all types of units and mechanisms, weapon, tools and equipment, which require long-lasting lubricating

effect. It restores the mobility of units and parts; it can penetrate easily and quickly into the rusted or jammed joints,

lubricates and separates them. Lubricates reliably and protects from corrosion and oxidation.

Advantages

• Reliably lubricates with a thick grease layer.

• Easily penetrates into joints.

• Possesses enhanced anticorrosive properties, provideslong-term preservation of the mechanisms if stored

outdoors.

• Protects from penetrating of water, dust, dirt.

• Owing to revitalizant, it compensates wear and prolongslife span of the mechanisms by 2-4 times.

320 mlArt. XB 40003

аerosol can

500 mlArt. XB 40103

аerosol can

150 mlArt. XB 40203

аerosol can

150 mlArt. XB 30001

аerosol can


30/40

Lubricants30 |

Lithium universal grease

Universal consistent grease with EP (Extreme Pressure) formula.

It is applied to lubricate and protect assemblies and joints operating under high thermal and mechanical loads. It isused to lubricate friction and frictionless bearings of various assemblies and mechanisms. Thanks to ЕР (Extreme

Pressure) complex, it protects mechanisms from destructive wear while operating and when the use of regular lithium

greases is not permitted.

Advantages

• Possesses high mechanical and chemical stability andkeeps protective and anti-wear properties even after

prolonged mechanical and thermal loads.

• Owing to the strong adhesive properties, it remainson the lubricated surfaces even under the action of

vibration and high rotation speeds.

• Water-resistant and can be used in assembliesoperating in contact with water.

• Forms a good isolation and prevents (unit) bearingcontamination.


With pressurized application.

Add the grease through the zerk until desired grease

volume is reached.

Manual application.

Eliminate the previous grease and ll 1/2 of bearing

volume (unit) with Lithium universal grease.

Grease in aerosol can.

1. Shake the can.

2. Spray a thin layer of the grease onto cleaned part.

Note

Compatible with automotive and industrial lithium greases of all types,

and can be mixed with them in any proportion.

Efcient for assemblies with the rotation speed up to 10,000 rpm.

5 mlpacket from foil-clad cellophane

125 mlArt. XB 30250plastic tube

450 mlArt. XB 30050grease guncartridge


NLGI 2 (ASTM D217)

ISO-L-XBCEB 2 (ISO 6743-9)

KP2K-20 (DIN 51502)

Requirements


31/40

| 31

Lithium complex grease

Universal lithium consistent grease with metal conditioner.

It is used to lubricate and protect assemblies and joints operating under heavy thermal and mechanical loads. It isrecommended for automotive assemblies and bearings as well as for industrial equipment. Due to the metal conditioner,

the grease signicantly reduces friction losses and protects the parts from wear.

Advantages

• Provides reliable lubrication of assemblies andmechanisms under overloads and high temperatures

for a long period of time. Signicantly decreases

friction losses and effectively protects parts from wear.

Reduces energy consumption.

• It is used in assemblies with single grease lling for the whole period of operation.

• It prevents formation of rust and corrosion. Owing tostrong adhesion, it remains on the lubricated surfaces

even with strong vibration and high rotation speeds.

• Possesses excellent moisture and dust protectionproperties.






volume is reached.

Manual application.


volume (unit) with Lithium complex grease.

Note



Efcient for assemblies with the rotation speed up to 10,000 rpm.

NLGI 2 (ASTM D217)

ISO-L-XBDIB 2 (ISO 6743-9)

KP2N-30 (DIN 51502)

Requirements


32/40

Lubricants32 |32 |

Lithium grease for CV joints

Consistent grease with molybdenum disulde (MoS2) for constant velocity joints.

It is recommended for application in constant velocity joints, assemblies and bearings of vehicles as well as industrialequipment. It contains pure superne molybdenum disulde (MoS2) owing to which it effectively protects assemblies

and bearings operating under peak and/or oscillatory loads.

Advantages

• Special grease for constant velocity joints.

• Effectively protects assemblies and bearings operatingunder peak and/or oscillatory loads.

• Possesses high mechanical and chemical stability,keeps protective and anti-wear properties even afterprolonged mechanical and thermal loads.

• Owing to strong adhesion, it remains on the lubricatedsurfaces even under the action of vibration and high

rotation speeds.

• Water-resistant and can be used in assembliesoperating in contact with water.

• Forms a good isolation and prevents bearings fromcontaminations.




volume is reached

Manual application.


volume (unit) with Lithium grease for CV joints.

Note



Applied for assemblies with the rotation speed up to 10,000 rpm.



NLGI 2 (ASTM D217)

ISO-L-XСCEB 2 (ISO 6743-9)

KPF2N-25 (DIN 51502)

Requirements


33/40

| 33

Advantages

Silicon lubricant

Universal dense silicon spray lubricant.

It lubricates and penetrates into joints made of various materials (metal, plastics, rubber, leather and wood in anycombination). It eliminates creaking of plastic panels, slideblocks and belts. It restores the easiness of lock work. It is

used as a preserving anticorrosion substance for cables, control rods and levers. It possesses perfect water resistant

properties due to the formation of multi-molecular layer of silicon. It prevents plastic and rubber parts from cracking on

the sun.

•Cleans and restores plastic, vinyl and rubber surfaces.

• Gives shine and polishes control panels, restorestheir original color and appearance; restores the

appearance of vinyl body upholstery and takes care of

the rubber tire covers.

• Restores the elasticity of seals.

• Prevents adhesiveness of rubber to metal; restoreselasticity of gaskets.

• Protects from corrosion and sunlight.

• Displaces moisture and dust, dries electrical contactsand forms the antistatic lm.

• Prevents freezing and ice-formation of rubber sealingof vehicle doors and hatches.

• Separates and protects parts during industrialpunching and gas welding.


1. Shake the can.

2. Spray a thin layer onto a work surface (part, joint).

3. If necessary, wipe it with a napkin.

4. 4. In case of severe contaminations, repeat the

treatment.





34/40

34 |

Assembly grease paste

Brake Caliper Grease

Assembly grease paste for easy assembling and disassembling of joints which

operate at high temperatures.

Grease paste designed to assemble and disassemble the units which operate at high

temperatures for a long period of time. Used for anges and thread pieces of nozzles of

the exhaust system, screw joints of the turbo compressor body, sparkplug threads etc.

High-temperature grease for guide ngers of brake caliper sliding carriage.

Special high temperature grease applied to prevent sticking and seizing of brake pads

on guide ngers of sliding carriage.

Advantages

• Makes joint assembling easy.

• Makes easy further disassembling of joined parts which operate at high temperatures for long period

of time.

• Has separating and lubricating effect.

• Prevents burning and sticking of parts, and formationof heat scale.

• Resistant to high loads.

• Efcient within the temperature range –35…+1,100 °С.

Advantages

• Provides accurate operation of the whole sliding carriage mechanism,

absolute abutment of brake pads and

quick unbraking of a brake disc at the

end of braking.

• Prolongs the service life of the wholebraking system of a vehicle.

• Eliminates noise and creaks whenbraking.

• Resistant to high loads.

• Has a wide temperature range ofapplication: –35…+400 °С

Applicationinstructions

1. Shake the can.

2. Spray a thin layeronto the clean part’s

surface.


1.Twist out the guide ngers of a brake

caliper.

2. Shake the can.

3. Apply a thing layer of the grease.

4. Assemble the unit.


320 mlArt. XB 40019

аerosol can

Note

Use when replacing brakepads or next maintenance

work.

Products for locks


35/40

| 35

Lock lubricant

Penetrating spray lubricant for automobile locks.

Lubricates and ensures easy operation of the lock mechanism.

Removes moisture from the parts’ surfaces and protects them from corrosion.


1. Shake the can.

2. Spray the content (2–3 sec.) into the keyhole.

50 mlArt. XB 40030

аerosol can

Lock de-icer

Aerosol product designed to defrost automobile locks.

Quickly unfreezes the iced parts of the lock mechanism and restores their mobility.

Defrosts ice and removes moisture from the surface of the parts, prevents their further

freezing.


1. Shake the can.

2. Spray the content (2–3 sec.) into the keyhole. The lock will thaw in

a minute.

It is recommended to use the product every 2 weeks in winter.


Lubricating lock de-icer

Universal care product for automobile locks.

Quickly defrosts the iced parts of the lock mechanism and recovers their mobility.

Lubricates the parts and protects them from corrosion.


1. Shake the can.

2. Spray the content (2–3 sec.) into

the key-hole.

50 mlArt. XB 40033

аerosol can

320 mlArt. XB 40133

аerosol can


36/40

Gun cleaning grease

Gun cleaning grease-spray for constant use. Contains revitalizant.

It is used to clean and lubricate the rearms. It provides fast and easy cleaning of small bore and large caliber ried

and smooth bore arms of all types (hunting, sporting, ghting and antique ries). It is recommended for everyday care

of arms with frequent shooting (in a shooting range or during hunting). It provides a reliable protection from corrosion.

Advantages

• Quickly displaces soiling from nooks of breechmechanisms and triggers.

• Special cleaning components of the grease can easilydissolve gunpowder scale in the barrel bore.

• Effectively lubricates threaded, rotary and pinning joints and protects them from corrosion.

• Guarantees perfect operation of the arms.

• Owing to revitalizant, the grease keeps the surface ofthe barrel bore in a perfect condition.


1. Shake the can.

2. Spray onto all parts and mechanisms of the arms.

3. Clean the arms.

Note

Does not contain alkali, neutral to plastics, wood, painted and

lacquered surfaces and bluing.

Does not require to be wiped dry.

When preparing the arms for a long-term storage, it is advised to use

VERYLUBE Gun conserving crease.

75 mlArt. XA 40003аerosol can


500 mlArt. XB 41903aerosol can with2-position spray

36 | Firearms' care products


37/40

| 37

Gun conserving grease

Gun conserving grease-spray for conserving, cleaning and lubricating the arms before storage. Contains

revitalizant.

It provides reliable protection of the arms from corrosion even if stored for a long time outdoors. It is used for a small bore

and large caliber ried and smooth bore arms of all types (hunting, sporting, ghting and pneumatic). It is used to take

care of arms after shooting and prepare them for storage.

Advantages

• Helps to prepare the arms for storage quickly.

• Possesses high penetrating ability and gets to all partsof the arms.

• Special inhibiting components of the grease neutralizeaggressive actions of the scale particles left after

cleaning.

• Possesses prefect low-temperature properties,provides the mobility and smoothness of the

mechanism operation at the ambient temperature up

to –60 °С.

• Thanks to the revitalizant, it keeps the surface of thebarrel bore in a top condition.


1. Shake the can.

2. Spray a thin layer onto the work surface (part, joint).

3. If necessary, wipe with a napkin.

4. If heavily contaminated, repeat the treatment.

75 mlArt. XA 40004аerosol can




38/40

Firearms' care products38 |38 |

Cleaning foam for gun barrels

Safe product for cleaning the internal surfaces of the barrel bore from copper residues.

Applied to ried and smooth-bore arms of any caliber. Foam cleaning method of barrels is approved by NATO.

Due to its high efciency and safety, the foam cleaning method exceeds barrel cleaning methods with special oils and

wire brush.

Advantages

• Quickly (15-30 min) and easily removes soft metalresidues from the inner surface of the barrel bore.

• Acts safely; contains special components inert tothe metals of the barrel (breech-block) surfaces;

selectively dissolves copper (brass) residues.

• Can be used for regular arms cleaning (from scale andgun powder gases).

• Environmentally friendly, non toxic.


1. Let the gun cool down to the room temperature,

disassemble it for cleaning. Close the barrel breech

(with a rag, false cartridge etc.).

2. Shake the can.

3. Spray the content into the barrel bore till the foam

appears from the muzzle.

4. Wait for 15-30 min, then remove the foam remains

with a clean rag. (As a result of the reaction with

copper compounds the foam becomes blue).

5. Repeat the foam cleaning if necessary.

6. After the cleaning, treat the barrel with the grease

(VERYLUBE Gun cleaning or Gun conserving

grease).

One can (500 ml) is enough for cleaning of Win. 308

barrel ( 7.62 ml) for approximately 100 times.




39/40


40/40

Head ofce: 4, 23 Augusta Lane,

Kharkov, 61103, Ukraine

Tel.: +38 (057) 717-55-55, 717-44-44,

fax +38 (057) 714-11-11.

www.xado.com, info@xado.сom

www.verylube.com

The manufacturer has the right to change

the design of the products’ packaging. All

rights to the presented trade marks and

logos belong to their legal owners. Style,

design and contents are the object of

copyright of XADO Ltd. and protected by law.

Reprinting and other application of materials

without written authorization by XADO Ltd.

is prohibited and involves responsibility

according to the existing legislation.

Date post:	07-Aug-2018
Category:	Documents
Upload:	nicolai-belocosov
View:	212 times
Download:	0 times

Verylube-catalogue-2013-En_web.pdf

Documents