For NOKIA 3650,3660,7650
Step 1 : Configuring the Service settings
From the main menu, go to Tools folder and select Settings > Connection > Access points
From Access Points menu, select Options > New Access point > Use default settings.
Next, for each of the fields enter accordingly • Connection name - mms • Data bearer - GPRS • Access point name - bsnlmms • User name - ppp • Prompt Password - No• Password - ppp123• Authentication - Normal• Gateway IP address – 10.31.54.2• Homepage - http://10.31.53.18/mms/ • Connection Security - off• Session mode - Permanent
Step 2 : Configuring the Message settings
From the main menu, go to Messaging and select Options > Settings > Multimedia Message to open the list of settings.
Next, for each of the fields enter accordingly • Preferred connections - Select mms as configured in Step 1. • Secondary connections - Use the name 'mms' as configured in Step 1. • Multimedia reception - Set to 'Always on'. • On receiving msg. - Set to 'Retr. immediately'. • Allow anon. messages - Set to 'Yes'. • Receive adverts - Set to 'Yes'. • Receive reports - Set to 'Yes'. • Deny Report sending - Set to 'No'. • Message validity - Set to 'Maximum time'. • Image size - Set to 'Small'. • Speaker - Set to 'Loudspeaker'.
For Motorola V600,V80,V220,V620
Configuring the WAP Setting
From the main menu, go to Menu and select Web Access > Web Sessions > [New Entry]
Under Entry Details, select Change and enter the following fields accordingly: • Name - mms• Homepage - http://10.31.53.18/mms/• Service Type 1 - select WAP• Gateway IP 1 – 10.31.54.2• Port 1 - 9201• Domain 1 - skip• Service Type 2 - select WAP• Gateway IP 2 - remain as default• Port 2 - 9201• Domain 2 - skip• DNS 1 - remain as default (000.000.000.000)• DNS 2 - remain as default (000.000.000.000)• Timeout - select 10 minutes• CSD No. 1 - skip• User Name 1 - skip• Password 1 - skip• Speed (Bps) 1 - select 9600 • Line Type 1 - select ISDN• CSD No. 2 - skip• User Name 2 - skip• Password 2 - skip• Speed (Bps) 1 - select 9600 • Line Type 1 - select ISDN• GPRS APN - bsnlmms • User Name - ppp• Password - ppp123
Then go to msg center menu, msg setup, mms msg setup and then put “server info “ as mms
For Sony Ericsson T610,T630,Z600
Step 1 : Configuring the Service settings
Go to Connectivity and select Data Comm. > Data accounts > New account > GPRS data
For each of the fields enter : • Name - mms • APN - bsnlmms • User name - ppp • Password - ppp123
Step 2: Configuring the WAP services settings
Go to Connectivity and select WAP options > WAP profiles > New profile
Next, for each of the fields, enter : • Name (Mandatory ) - mms • Connect using (Mandatory) - mms as configured in Step 1 • IP address (Mandatory) - 10.31.54.2 • Advanced > Change homepage
For each of the fields, enter : • Name - mms• Address - http://localhost/home.wml• Security - Off • Show pictures - On
Step 3: Configuring the Message settings
Go to Messaging and select Picture> Options • Validity period - 'Maximum'. • Read Report - Set to 'Off'• Delivery Report - Set to 'Off'. • Content alert – Set to ‘On’ .• Message server - http://10.31.53.18/mms/ • WAP Profile - Select mms as configured in Step 2.
Go to Messaging and select WAP push > Allow push > Always
For NOKIA 3100 / 3200 / 3300 / 3530 / 5100 / 6100 / 6610 / 6800 / 7210 / 7250 / 8910i
Configuring the Message settings From the main menu, go to Messages and select Message Settings > Multimedia msgs. Next, for each of the fields enter accordingly • Save sent messages – Yes • Allow Multimedia Reception – Yes • Incoming multimedia messages – Retrieve • Connection Settings: • Active Multimedia settings – mms as configured below • Edit active multimedia settings : - Settings name – mms - Homepage – http://10.31.53.18/mms/ - Session mode – Permanent - Data Bearer – GPRS - GPRS access point – bsnlmms - IP address – 10.31.54.2 - Authentication type – Normal
- Username – ppp- Password – ppp123.
• Allow adverts – Yes
Manual configuration for LG G5300 / G7100
Configuring the Message setting
From the main menu, go to Messages and select Settings > Multimedia message > Network settings
Select a new user define field and enter accordingly: • Rename – mms• Homepage – http://10.31.53.18/mms/ • Bearer – GPRS • GPRS settings: – IP address – 10.31.54.2 – APN – bsnlmms – User ID – ppp – Password – ppp123 • Connection type – Continuous
Manual configuration for LG G8000
Configuring the Message settings
From the main menu, go to Messages and select Settings > MMS> Connection
Select a new user define field and enter accordingly: • Access point description – mms • User name – ppp • Password – ppp123 • MMSC address – http://10.31.53.18/mms/ • WAP IP address – 10.31.54.2 • Bearer – GPRS • Access point name – bsnlmms
Manual configuration for Motorola V690 / V878
Configuring the Message Settings
Go to main menu, select Msg. centre > Settings > Multimedia msgs. > Connection settings > Edit New Profile
For each of the fields, enter accordingly:• Profile name – mms• Homepage – http://10.31.53.18/mms/• Session mode – Permanent• Connection security – OFF• Data Bearer – GPRS• IP address – 10.31.54.2• Authentication type – Normal• User Name – ppp• Password – ppp123
Manual configuration for Motorola E365
Configuring the Message Settings
Go to main menu, select Messages > Message Settings > Inbox Setup > Multimedia Msg Setup > Profile Service > MMS Setting
For each of the fields, enter accordingly:• Profile name – mms
Under Bearer Type – GPRS• User Name – ppp• Password – ppp123• Apn – bsnlmms
Under WAP SettingPrimary IP – 10.31.54.2Primary Port – 9201Homepage – http://10.31.53.18/mms/
Manual configuration for Motorola MPX200
Configuring the Service settings
Go to main menu, select Programs > More > More > Accessories > MMS Setup > Profile
• MMS Profile – select mms • Go to Profile > select Edit - Profile : enter mms - MMSC: enter http://10.31.53.18/mms/ - Data Connections: select mms - Gateway: select WAP 1.0 Gateway - IP Address – enter 10.31.54.2 - Port: enter 9201 - Encoding: select Binary Encoding
Configuring the WAP settings
Go to main menu, select Programs > More > Settings > Data Connections
Under Secure WAP connection:Go to Menu > Edit Connections > GPRS Connections > mms
• Connects to: select MMS Connection• Access point – enter bsnlmms• User Name – enter ppp• Password – enter ppp123• Primary DNS: remain as default (0.0.0.0)• Secondary DNS: remain as default (0.0.0.0)• IP address: enter 10.31.54.2
Manual configuration for Motorola V300 / V303
Configuring the Message Settings
Go to main menu, select Message CentreClick on Menu button > Message Setup > MMS Message Setup > Server Info > New
For each of the fields, enter accordingly:• Service Name – mms• Server Name - http://10.31.53.18/mms/• Web Session Name – mms
Manual configuration for Motorola V680
Configuring the WAP Setting
From the main menu, go to Main Menu and select Telephone tab > Network
Under Network, select Add icon and enter the following fields accordingly: • Profile Name - mms• APN - bsnlmms • User Name - ppp• Password - ppp123 • Timeout - Off• Select DNS Server - 10.31.54.2• Baud Rate - 9600• Line Type - Modem• Timeout - Off
Leave the other fields blank
Manual configuration for Motorola V690 / V878
Configuring the Message Settings
Go to main menu, select Msg. centre > Settings > Multimedia msgs. > Connection settings > Edit New Profile
For each of the fields, enter accordingly:• Profile name – mms• Homepage – http://10.31.53.18/mms/• Session mode – Permanent• Connection security – OFF• Data Bearer – GPRS• IP address – 10.31.54.2• Authentication type – Normal• User Name – ppp• Password – ppp123
Manual configuration for Motorola C650
Configuring the WAP Setting
From the main menu, go to Menu and select Web Access > Web Sessions > [New Entry]
Under Entry Details, select Change and enter the following fields accordingly: • Name - mms• Homepage - http://10.31.53.18/mms/• Service Type 1 - select WAP• Gateway IP 1 - 10.31.54.2• Port 1 - 9201• Domain 1 - skip• Service Type 2 - select WAP• Gateway IP 2 - skip• Port 2 - 9201• Domain 2 - skip• DNS 1 - remain as default (000.000.000.000)• DNS 2 - remain as default (000.000.000.000)• Timeout - select 10 minutes• CSD No. 1 - skip• User Name 1 - skip• Password 1 - skip
• Speed (Bps) 1 - select 9600 • Line Type 1 - select ISDN• CSD No. 2 - skip• User Name 2 - skip• Password 2 - skip• Speed (Bps) 1 - select 9600 • Line Type 1 - select ISDN• GPRS APN - bsnlmms • User Name - ppp• Password - ppp123
Configuring the Message Setting
Press the Menu button.
From the main menu, go to Menu and select Messages > Message Setup > MMS Message Setup > Server Info
• Select mms
Manual configuration for Motorola A760
Tap on the third icon at the top of the phone, then tap on the last icon at the bottom right-hand side. Select Service setup. Select Multimedia Message.
Proxy profile - tap on the file icon next to it for a list of network providers. Tap on mms
• Profile Name: mms• Server address: http://10.31.53.18/mms/• Using profile: mms• WAP gateway IP: 10.31.54.2• Connect security: Off• Connection Type: Connection
Tap Done.
You will see mms again on screen with other service provider settings like Gee! Or e-ideas. Tap and hold on mms, select Set as Default.
Manual configuration for Motorola E398
Select menu, WebAccess, Web SessionsSelect menu option(in bet. Launch & Exit button), click New
Name : mmsHomepage : Leave blankService type : WAPGateway IP : 10.31.54.2 Port 1 : 9201Domain 1 : Leave blankScroll down till,GPRS APN : bsnlmmsUser Name : ppp Password : ppp123Select done
Go to Menu, MessagesMenu option, Message Setup, MMS Message SetupHide Fields : Leave as default(user preference)Autosignature : Leave blankDownload : AutomaticFilter : Leave blankExpire After : Leave as default(user preference)Reply Type : MMSSize Limited : 100 KBServer Info : Select mms (if there is no profile, proceed to create as below)
Select menu option, NewService Name : mmsServer Name : http://10.31.53.18/mms/Web Session Name : Select mms
Manual configuration for Motorola MIO 8870
Configuring the WAP Settings
Go to main menu, select Start > Settings > More > Data Connections
Under Secure WAP connection: Go to Menu > Edit Connections > GPRS Connections > gprs
• Connects to: select MMS Network• Access point - enter bsnlmms• User Name - enter ppp• Password - enter ppp123• Primary DNS: remain as default (0.0.0.0)• Secondary DNS: remain as default (0.0.0.0)• IP address: enter 10.31.54.2
Manual configuration for Motorola A668
Configuring the WAP Setting
From the main menu, go to Main Menu and select Browser > Profiles
Choose a Profile
> Edit• Homepage - http://10.31.53.18/mms/• Sesstion mode - permanent• Connection security - ON• Data bear - GPRS• IP address - 10.31.54.2• Authentication type - Normal• User Name - ppp• Password - ppp123
> Rename• Name - mms
> Activate
Manual configuration for Motorola V3
Configuring the WAP Setting From the main menu, go to Menu and select Web Access > Web Sessions > [New Entry]
Under Entry Details, select Change and enter the following fields accordingly:
• Name – mms• Homepage – http://10.31.53.18/mms/• Service Type 1 – select WAP• Gateway IP 1 – 10.31.54.2• Port 1 – 9201• Domain 1 – skip • Service Type 2 – select WAP• Gateway IP 2 – skip• Port 2 – 9201• Domain 2 – skip• DNS 1 – remain as default (000.000.000.000)• DNS 2 – remain as default (000.000.000.000)• Timeout – select 10 minutes• CSD No. 1 – skip• User Name 1 – skip• Password 1 – skip • Speed (Bps) 1 – select 9600 • Line Type 1 – select ISDN• CSD No. 2 – skip• User Name 2 – skip • Password 2 – skip • Speed (Bps) 1 – select 9600 • Line Type 1 – select ISDN• GPRS APN – bsnlmms • User Name – ppp• Password – ppp123
Configuring the Message Setting
Press the Menu button.
From the main menu, go to Menu and select Messages > MMS templates (click on the centre key) > Message Setup > MMS Message Setup > Server Info
• Service Name: mms• Server Name: http://10.31.53.18/mms/• Web Session Name: mms
Manual configuration for Nokia N-Gage QD
Configuring the WAP Setting
From the main menu, go to Tools > Settings > Connection > Access points > select Options > New access point > Use default settings
Next, for each of the fields enter accordingly: • Connection name - mms• Data Bearer - GPRS• Access point name - bsnlmms• Username - ppp• Prompt password - No• Password - ppp123• Authentication - Normal• Gateway IP address - 10.31.54.2• Homepage - http://10.31.53.18/mms/• Connection security - Off• Session mode - Permanent
Configuring the Message Setting
From the main menu, go to Messaging and select Options > Settings > Multimedia message
Next, for each of the fields enter accordingly: • Access point in use - mms (as above)• Secondary conn. - None• Multimedia reception - Always On• On receiving msg. - Retr. Immediately• Allow anon. Messages - No • Receive adverts - Yes• Receive report - No• Deny report sending - No• Message validity - Maximum time• Image size - Large• Default speaker - Handset
Manual configuration for Nokia 6108 Configuring the Message settings From the main menu, go to Messages and select Message Settings > Multimedia msgs. Next, for each of the fields enter accordingly • Save sent messages – Yes • Allow multimedia reception – Yes • Incoming multimedia messages – Retrieve • Connection Settings: • Active Multimedia settings – mms as configured below • Edit active multimedia settings : - Settings name – mms - Homepage – http://10.31.53.18/mms/ - Session mode – Permanent - Data Bearer – GPRS - Bearer settings - GPRS access point – bsnlmms - IP address – 10.31.54.2 - Authentication type – Normal - Username – ppp • Password – ppp123
Manual configuration for Nokia 6220 / 6820
Configuring the Message Settings
From the main menu, go to Messages and select Message settings > Multimedia msgs.
For each of the fields, enter accordingly: • Save sent messages – Yes • Allow multimedia reception – Yes • Incoming multimedia messages – Retrieve • Connection settings – Active Multimedia settings – mms as configured below – Edit active multimedia settings : - Settings’ name – mms- Homepage – http://10.31.53.18/mms/- Proxies – Enable
- Primary proxy – 10.31.54.2- Primary proxy Port - 9401- Secondary proxy Port – 9401- Data Bearer – GPRS- Bearer settings - GPRS access point – bsnlmms- Authentication type – Normal- Username – ppp- Password – ppp123 • Allow adverts – Yes
Manual configuration for Nokia 6600 Configuring the Message Setting From the main menu, go to Messages and select Option > Settings > Multimedia message > New Access point. For each of the fields enter accordingly: Connection Settings: • Access point is use: - Settings’ name – mms - Connection name – mms - Data Bearer – GPRS - Access point name – bsnlmms - User name – ppp - Prompt password – No - Password – ppp123 - Authentication – Normal - Gateway IP address – 10.31.54.2 - Homepage – http://10.31.53.18/mms/ - Advanced settings: - Phone IP address – Automatic - Primary Name Server – 0.0.0.0 - Secondary Name Server – 0.0.0.0 - Proxy Server Address – 10.31.54.2 - Proxy Port Number – 9401 • Receive adverts: Yes
Manual configuration for Nokia 7600
Configuring the Message Settings
From the main menu, go to Messages and select Message settings > Multimedia msgs.
For each of the fields, enter accordingly: • Save sent messages – Yes • Allow multimedia reception – Yes • Incoming multimedia messages – Retrieve • Connection settings – Active Multimedia settings – mms as configured below – Edit active multimedia settings : - Settings’ name – mms- Homepage – http://10.31.53.18/mms/- Proxies – Enable- Primary proxy – 10.31.54.2- Primary proxy Port - 9401- Secondary proxy – 10.31.54.2 - Secondary proxy Port – 9401- Bearer settings - GPRS access point – bsnlmms- Authentication type – Normal- Username – ppp- Password – ppp123 • Allow adverts – Yes
Manual configuration for Nokia 7610
Configuring the WAP Setting
From the main menu, go to Tools > Settings > Connection > Access points > select Options > New access point > Use default settings
Next, for each of the fields enter accordingly • Connection name - mms • Data bearer - GPRS • Access point name - bsnlmms • User name - ppp • Prompt Password - No• Password - ppp123• Authentication - Normal• Gateway IP address - 10.31.54.2• Homepage - http://10.31.53.18/mms/
Configuring the Message Setting
From the main menu, go to Messaging and select Options > Settings > Multimedia message
Next, for each of the fields enter accordingly • Access point in use - mms (as above)• Multimedia reception - Always on• On receiving msg. - Retr. immediately• Allow anon. messages - No. • Receive adverts - Yes• Receive report - No• Deny report sending - No• Message validity - Maximum time• Image size - Large
Manual configuration for Nokia 5140 Configuring the Message settings From the main menu, go to Messages and select Message Settings > Multimedia msgs. Next, for each of the fields enter accordingly • Save sent messages – Yes • Allow multimedia reception – Yes • Incoming multimedia messages – Retrieve • Connection Settings: • Active Multimedia settings – mms as configured below • Edit active multimedia settings : - Settings name – mms - Homepage – http://10.31.53.18/mms/ - Proxies – Enable - Primary Proxy – 10.31.54.2 - Port – 9401 - Secondary Proxy – skip - Port – 9401 - Data Bearer – GPRS - Bearer settings - GPRS access point – bsnlmms - Authentication type – Normal - Username – ppp - Password – ppp123
Manual configuration for Nokia 7270
Configuring the Message Setting
Step 1From the main menu, go to Settings and select Personal Configuration > Multimedia msgs.
Next, for each of the fields enter accordingly: Account Name – mms Server Address – Access point settings > Proxy – Enable > Proxy Address – 10.31.54.2 > Proxy port – 9401 > Bearer settings:
> GPRS access point – bsnlmms> Authentication type – Normal> Username – ppp> Password – ppp123> Verify new password – ppp123
Step 2From Main menu, go to Messages > Message settings> Multimedia msgs
• Save sent messages – Yes• Allow multimedia reception – Yes• Incoming multimedia messages – Retrieve• Configuration settings – Personal config• Account – mms
Manual configuration for Nokia 6170
Configuring the Message Setting
Step 1From the main menu, go to Settings and select Configuration Settings >Personal Configuration Settings > Option > Add New > Multimedia Msg
Next, for each of the fields enter accordingly: Account Name – mmsServer Address – http://10.31.53.18/mms/ Access point settings > Proxy – Enable > Proxy Address – 10.31.54.2 > Proxy port – 9401 > Bearer settings: > GPRS access point – bsnlmms> Authentication type – Normal> Username – ppp> Password – ppp123> Verify new password – ppp123
Step 2From Main menu, go to Messages > Message settings> Multimedia msgs
• Save sent messages – Yes• Allow multimedia reception – Yes• Incoming multimedia messages – Retrieve• Configuration settings > Configuration – Personal config > Account – mms
Manual configuration for Nokia 6670
Step 1: Configuring the WAP Setting
From the main menu, go to Settings > Connection > Access points > select Options > New access point > Use default settings
Next, for each of the fields enter accordingly:
• Connection name – mms• Data Bearer – GPRS• Access point name – bsnlmms• Username – ppp• Prompt password – No• Password – ppp123• Authentication – Normal• Homepage – http://10.31.53.18/mms/
Back > Option > Advance settings
Proxy server address – 10.31.54.2Proxy port number – 9401
Step 2: Configuring the Message Setting
From the main menu, go to Messaging and select Options > Settings > Multimedia message.
Next, for each of the fields enter accordingly:
• Access point in use – mms (as above)• Multimedia reception – Always On• On receiving msg. – Retr. immediately• Allow anon. Messages – No • Receive adverts – Yes• Receive report – No• Deny report sending – No• Message validity – Maximum time• Image size – Large
Manual configuration for Sony Ericsson T230 / T300 / T310 / T610 / T630
Step 1 : Configuring the Service settings
Go to CONNECT and select Data Comm. > Data accounts > Add account > GPRS data
Next, for each of the fields enter : • Name - mms • APN - bsnlmms • User name - ppp • Password - ppp123 • Click Save
Step 2: Configuring the WAP services settings
Go to WAP services and select Options > Common > Push Access > ON
Go to WAP services and select Options > WAP Profiles > Add Profile
Next, for each of the fields enter : • Name (Mandatory ) - mms • Connect using (Mandatory) - mms as configured in Step 1 • IP address (Mandatory) - 10.31.54.2 • Save• Select mms > Edit > Chg homepage For each of the fields enter : • Name - mms • Address -• Data mode - Conn Oriented• Security - OFF • Show Picture - ON • Response timer - 150Step 3: Configuring the Message settings
Goto to Messages and select MMS > Options • Validity period - 'Maximum time'. • Read Report - Set to 'Off'• Delivery Report sending - Set to 'Off'. • Auto delete - Set to 'Off'. • Auto download - Set to 'On'• Message server - http://10.31.53.18/mms/ • WAP Profile - Select mms as configured in Step 2.
Manual configuration for Sony Ericsson P800 / P900
Step 1 : Configuring the Service settings
From the main menu, go to Control Panel and select Connections > Internet accounts > Accounts > New
For each of the fields, enter accordingly:• Account name - mms • Connection type - GPRS
Next, select Advanced and input accordingly:• User name and password required - • User name - ppp• Password - ppp123 • Address - bsnlmms• Click Done
Step 2: Configuring the WAP settings
From the main menu, go to Control Panel and select Connections > WAP accounts > Basic > New
For each of the fields, enter accordingly:• Account name - mms • Internet account - mms as configured in Step 1 • Use Proxy - • Address - 10.31.54.2• Port - 9201• Click Done
Step 3: Configuring the Message settings
From the main menu, go to Control Panel and select Connections > Messaging accounts > mms
For each of the fields, enter accordingly: • Service centre address - http://10.31.53.18/mms/• Wap account - mms as configured in Step 2• Automatic - On• Download size - No restrictions
Select Advanced and input accordinglyAt Send tab, • Validity period - MaximumAt Receive tab,• Allow delivery notification - • Allow read notification - • Click Done
Step 4: Configuring the Service Inbox
From the main menu, go to Internet and select Edit > Preferences > Advanced• Enable WAP Push -
Manual configuration for Siemens MC60 / S57 / SL55
Step 1 : Configuring the Service settings
From the main menu, go to Setup and select Connectivity > Data services > MMS, WAP > Empty 2 (or any empty/unused account) > Options > Rename > Profile name - mms Note: can also use gprs Profile
Next, select GPRS settings, and Edit accordingly • APN: bsnlmms • Login name - ppp• Password - ppp123 • Click Save
Step 2 : Configuring the Message settings
From the main menu, go to Messages and select Msg.setup > MMS > Options
Next, select each of the options, and enter as necessary Rename - mms Change sett. - • Expiry time - Maximum • Retrieval - Automatic • MMS relaysrv. - http://10.31.53.18/mms/ • IP settings as follows:
IP Address - 10.31.54.2 Port - 9201 • Connection Profile - mms as configured in Step 1
Manual configuration for Siemens M55 Step 1 : Configuring the Service settings
Go to main menu, select Setup > Connectivity > Data services > MMS, WAP > Empty 2 (or any empty/unused account) > Options > Rename > Profile name & key in mms
Next, select GPRS settings, and Edit accordingly:• APN - bsnlmms• Login name - ppp• Password - ppp123 • Click Save
Step 2 : Configuring the Message settings
Go to main menu > Messages > Msg. setup > MMS Options
Next, select each of the options, and key in where necessary: Rename - mms Under Change sett. - • Expiry time - Maximum • Retrieval - Automatic • MMS relaysrv. - http://10.31.53.18/mms/ • IP settings as follows: IP Address - 10.31.54.2 Port - 9201 • Connection Profile - mms
Manual configuration for Siemens ST60
Configuring the Message settings
From the main menu, go to Messages > MMS > MMS setup > MMS profile > Edit
• Profile name – mms • IP address – 10.31.54.2 • IP port – 9201 • Homepage – http://10.31.53.18/mms/ • GPRS Bearer – select gprs – Profile name: mms – GPRS APN: bsnlmms– Authentication: select Activate– User name: ppp– Password: ppp123– DNS: remain as default
Manual configuration for Siemens SX1
Step 1 : Configuring the Service settings
From the main menu, go to Setup > Settings > Connection > Access pointsFrom Access Points menu, select Options > New Access point > Use default settings.
Next, for each of the fields enter accordingly • Connection name - mms • Data bearer - GPRS • Access point name - bsnlmms • User name - +ppp • Prompt Password - No• Password - ppp123• Authentication - Normal• Gateway IP address - 10.31.54.2• Homepage - http://10.31.53.18/mms/ • Connection Security - off• Session mode - Permanent
Manual configuration for Siemens CF62
Configuring the Service setting
From the main menu, go to Surf & fun > Internet > Options > Setup > Profiles > select a Profile and Edit
• Profile name – mms• IP address – 10.31.54.2• Port – 9201 • Homepage – http://10.31.53.18/mms/• GPRS lingertime – 5 minutes• CSD lingertime – 180 seconds• Connection profile – select mms• Select Save
Configuring the Message setting
From the main menu, go to Messages and select Message setup > MMS setup > select <mms> and click Change > options > change settings
Next, select each of the options, and enter as necessary
Expiry time – select MaximumDefault prio. – NormalSlide duration – 10 secondsMMS relaysrv. – http://10.31.53.18/mms/Retrieval – select AutomaticIP settings –• IP address: 10.31.54.2• Port: 9201• 2nd IP address: 10.31.54.2• 2nd port: 9201Conn. Profile – select mms
Click OK
Manual configuration for Siemens CX65Configuring the Service setting
From the main menu, go to Surf & fun > Internet > Profiles > Options > Setup > Profiles > select a Profile and Edit:
• Profile name – mms• Homepage – http://10.31.53.18/mms/• Protocol – WAP/WSP• Gateway/Proxy Server ID – remain as default• IP address – 10.31.54.2• Port – 9201• Username proxy – ppp• Password proxy – ppp123 GPRS lingertime – 5 minutes• CSD lingertime – 180 seconds• Connection profile – mms
Configuring the Message setting
(1) From the main menu, go to Messages and select Message setup > MMS setup> Connection profile > Empty profile > Options
Rename – mms
Select this profile and Edit the necessary fields:
• CSD/GPRS profile – select mms • Relaysrv.-URL – http://10.31.53.18/mms/• Secure rel.serv. URL – skipped• MMS WAP/HTTP – select WAP• Gateway IP address – 10.31.54.2 Gateway port – 9201• Secure gateway IP – skip• Secure gatew. port – remain default as 9203
Activate
(2) From the main menu, go to Messages and select Message setup > MMS setup> User settings
Select Edit and enter the fields accordingly:
• Delivery report – select No• Default priority – select Normal• Expiry time – select Maximum• Page duration – 20 seconds (Automatic)• Retrieval – select Automatic• Creation mode – select Free• Size indication – 100kb (Lim.)
Manual configuration for Siemens C65
Configuring the Service setting
From the main menu, go to Surf & fun > Internet > Options > Setup > Profiles > select a Profile and Edit
• Profile name – mms• IP address – 10.31.54.2• Port – 9201 • Homepage – http://10.31.53.18/mms/• GPRS lingertime – 5 minutes• CSD lingertime – 180 seconds• Connection profile – select GPRS• Select Save
Configuring the Message setting
From the main menu, go to Messages and select Message setup > MMS setup > select <mms> and click Change > options > change settings
Next, select each of the options, and enter as necessary
Expiry time – select MaximumDefault prio. – NormalSlide duration – 10 secondsMMS relaysrv. – http://10.31.53.18/mms/Retrieval – select AutomaticIP settings –• IP address: 10.31.54.2• Port: 9201
• 2nd IP address: 10.31.54.2• 2nd port: 9201Conn. Profile – select GPRSClick OK Manual configuration for Siemens SL65
Configuring the Service setting
From the main menu, go to Surf & fun > Internet > Options > Setup > Profiles > select a Profile and Edit:
• Profile name - mms• IP address - 10.31.54.2• Port - 9201 • Homepage: http://10.31.53.18/mms/• GPRS lingertime: 5 minutes• CSD lingertime: 180 seconds• Connection profile - select GPRS• Login - ppp• Password - ppp123• Select Save
Configuring the Message setting
From the main menu, go to Messages and select Message setup > MMS setup > select <mms> and click <user settings>
Next, select each of the options, and enter as necessary Expiry time - select MaximumDefault prio. - NormalSlide duration - 10 secondsMMS relaysrv. - http://10.31.53.18/mms/Retrieval - select AutomaticIP settings - • IP address: 10.31.54.2• Port: 9201• 2nd IP address: 10.31.54.2• 2nd port: 9201Conn. Profile- select GPRS
Click OK
Manual configuration for Samsung V200
Configuring the Message Settings
Select Menu > Picture Messages > MMS Profile Next, for each of the fields, enter accordingly:
• Profile Name – mms• Connection URL – http://10.31.53.18/mms/• Security – Non-Secure• IP address – 10.31.54.2• User Name – ppp• Password – ppp123• APN – bsnlmms
Manual configuration for Samsung E100A / E700A / X100A
Configuring the Message Settings
Select Menu > Messages > Settings > Multimedia message > MMS profiles > Current profile
Next, for each of the fields enter accordingly: • Profile Name – mms • Server URL – http://10.31.53.18/mms/ • GRPS setting: Gateway – IP address – 10.31.54.2 APN – bsnlmms Login ID – ppp Password – ppp123
configuration for Samsung SGH D410C
Configuring the Message Settings
Select Menu > Multimedia Messages > MMS Profile > select an Empty Profile Next, for each of the fields, enter accordingly:
• Profile Name – mms• Connection URL – http://10.31.53.18/mms/
• Security – Non-Secure• IP address – 10.31.54.2• User Name – ppp• Password – ppp123• APN – bsnlmms
Manual configuration for Samsung X600A
Configuring the Message Settings
Select Menu > Messages > Settings > Multimedia message > MMS profiles > Current profile
Next, for each of the fields enter accordingly: • Profile Name – mms • Server URL – http://10.31.53.18/mms/ • GSM setting: Gateway – IP address – 10.31.54.2 – IP port - 9201 Data call type – select ISDN Login – ppp Password – ppp123 • GPRS setting: Gateway – IP address – 10.31.54.2 – IP port - 9201 APN – bsnlmms Login ID – ppp Password – ppp123 • Bearer – select GPRS only
Manual configuration for Samsung SGH D410C
Configuring the Message Settings
Select Menu > Multimedia Messages > MMS Profile > select an Empty Profile Next, for each of the fields, enter accordingly:
• Profile Name – mms• Connection URL – http://10.31.53.18/mms/• Security – Non-Secure• IP address – 10.31.54.2• User Name – ppp• Password – ppp123• APN – bsnlmms
Manual configuration for Samsung E600C
Configuring the Message Settings
(1) Select Menu > Multimedia MSGs. > SetupNext, for each of the fields, enter accordingly:
• Delivery Report - No• Read Reply - Yes• Auto Download - On• Message Acceptance - All• Hide ID - Yes• Expiry Date - Maximum• Delivery Time - Immediately• Priority - Normal• Report Allowed - Yes• Page Duration - O Second
(2) Select Menu > Multimedia MSGs. > MMS profile > Empty profileNext, for each of the fields, enter accordingly:
• Profile Name – mms• Connection URL – http://10.31.53.18/mms/• Security – Non-Secure• IP address – 10.31.54.2• User Name – ppp• Password – ppp123• APN – bsnlmms
Manual configuration for Samsung E800C
Configuring the Message Setting
Select Menu > Messages > Settings > Multimedia message > MMS profiles > Current profile
Next, for each of the fields enter accordingly:
• Profile Name – mms• Server URL – http://10.31.53.18/mms/• GSM setting – Gateway – IP address – 10.31.54.2 – IP port – 9201 Data call type – select ISDN Login – ppp Password – ppp123
• GRPS setting – Gateway – IP address – 10.31.54.2 – IP port – 9201 APN – bsnlmms Login ID – ppp Password – ppp123
• Bearer – select GPRS only
Manual configuration for Samsung SGH A460C
Configuring the Message Setting
Select Menu > Multimedia Messages > MMS Profile > select a Empty Profile
Step 1• Profile Name – mms• Server URL – http://10.31.53.18/mms/• GPRS setting > 1) Gateway > IP address – 10.31.54.2 >IP port – 9201 2) APN – bsnlwap 3) Login ID – ppp 4) Password – ppp123• Bearer – GPRS
Step 2Current Profile – mms Manual configuration for Samsung SGH E310C
Configuring the Message Setting
Select Menu > Multimedia Messages > MMS Profile > select a Empty Profile
Next, for each of the fields enter accordingly:
• Profile Name – mms• Connection URL – http://10.31.53.18/mms/• Security – Non-Secure• IP address – 10.31.54.2• User Name – ppp• Password – ppp123• APN – bsnlmms