Discrete Semiconductors and Passive ComponentsOne of the World’s Largest Manufacturers of
VSE-DB0097-1502
INTERACTIVEdata book
V I S H A Y I N T E R T E C H N O L O G Y , I N C .
Notes:
1. To navigate:
a) Click on the Vishay logo in any document to go to the overview page.
b) Click on the document name within the overview to go directly to the document.
c) Use the scroll or page up / page down functions.
d) Use the Adobe® Acrobat® page function in the browser bar.
2. To search the text of the catalog, use the Adobe® Acrobat® search function.
SURFACE MOUNT MULTILAYER CERAMIC CHIP CAPACITORS
VISHAY
Discrete Semiconductors and Passive ComponentsOne of the World’s Largest Manufacturers of
VSE-DB0097-1502DATA BOOK
VISHAY INTERTECHNOLOGY, INC.
SURFACE MOUNT MULTILAYER CERAMIC CHIP CAPACITORS
Vishay
CERAMIC CAPACITORS
SEMICONDUCTORS
MOSFETS SEGMENTMOSFETs
Low-Voltage TrenchFET® Power MOSFETsMedium-Voltage Power MOSFETsHigh-Voltage Planar MOSFETsHigh-Voltage Super Junction MOSFETs Automotive-Grade MOSFETs
ICsPower Management and Power Control ICs Smart Load SwitchesAnalog Switches and Multiplexers
DIODES SEGMENTRectifiers
Schottky RectifiersUltra-Fast Recovery RectifiersStandard and Fast Recovery RectifiersHigh-Power Rectifiers/DiodesBridge Rectifiers
Small-Signal DiodesSchottky and Switching DiodesZener DiodesTuner / Capacitance DiodesBandswitching DiodesRF PIN Diodes
Protection DiodesTVS Diodes or TRANSZORB®
(uni-directional, bi-directional)ESD Protection Diodes (including arrays)
Thyristors / SCRsPhase-Control ThyristorsFast Thyristors
Power ModulesInput Modules
(diodes and thyristors)Output and Switching Modules
(contain MOSFETs, IGBTs, and diodes)Custom Modules
OPTOELECTRONIC COMPONENTS SEGMENTInfrared Emitters and DetectorsOptical SensorsInfrared Remote Control ReceiversOptocouplers
Phototransistor, PhotodarlingtonLinearPhototriacHigh-SpeedIGBT and MOSFET Driver
Solid-State RelaysLEDs and 7-Segment DisplaysInfrared Data Transceiver Modules Custom Products
RESISTORS AND INDUCTORS SEGMENTFilm Resistors
Metal Film ResistorsThin Film ResistorsThick Film ResistorsMetal Oxide Film Resistors Carbon Film Resistors
Wirewound ResistorsVitreous, Cemented, and Housed ResistorsBraking and Neutral Grounding ResistorsCustom Load Banks
Power Metal Strip® ResistorsChip FusesVariable Resistors
Cermet Variable ResistorsWirewound Variable ResistorsConductive Plastic Variable ResistorsContactless Potentiometers
Networks / ArraysNon-Linear Resistors
NTC ThermistorsPTC ThermistorsVaristors
MagneticsInductorsTransformersCoils Connectors
CAPACITORS SEGMENTTantalum Capacitors
Molded Chip Tantalum CapacitorsCoated Chip Tantalum CapacitorsSolid Through-Hole Tantalum CapacitorsWet Tantalum Capacitors
Ceramic CapacitorsMultilayer Chip CapacitorsDisc Capacitors
Film CapacitorsPower CapacitorsHeavy-Current CapacitorsAluminum Electrolytic Capacitors
PASSIVE COMPONENTS
SEMICONDUCTORS
PR
OD
UC
T L
IST
ING
S
Vishay
Surface Mount Multilayer
Ceramic Chip Capacitors
Vishay Electronic GmbHDr.-Felix-Zandman-Platz 1
D-95100 SelbGermany
Phone: +49 9287 710Fax: +49 9287 70435
www.vishay.com
DisclaimerALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any otherdisclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose orthe continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and allliability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particularpurpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typicalrequirements that are often placed on Vishay products in generic applications. Such statements are not binding statementsabout the suitability of products for a particular application. It is the customer’s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular application. Parametersprovided in datasheets and/or specifications may vary in different applications and performance may vary over time. Alloperating parameters, including typical parameters, must be validated for each customer application by the customer’stechnical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustainingapplications or for any other application in which the failure of the Vishay product could result in personal injury or death.Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Pleasecontact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or byany conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category PolicyVishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill thedefinitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council ofJune 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE)- recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm thatall the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Freerequirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make referenceto the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21conform to JEDEC JS709A standards.
Table of Contentswww.vishay.com Vishay
Revision: 18-Feb-15 1
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Surface Mount Multilayer Ceramic Chip CapacitorsPart Numbering / Ordering Information................................................................................................................................ 2
MLCCs FOR COMMERCIAL APPLICATIONS (NME TECHNOLOGY)VJ Commercial Series ............................................................................................................................................................ 5
MLCCs FOR HIGH TEMPERATURE APPLICATIONS (NME TECHNOLOGY)VJ X8R .................................................................................................................................................................................... 20
MLCCs FOR AUTOMOTIVE APPLICATIONS (NME TECHNOLOGY)VJ....31X RoHS Automotive MLCC ........................................................................................................................................ 26VJ....31 / VJ....34 Automotive MLCC ..................................................................................................................................... 45
MLCCs FOR HIGH VOLTAGE AND SAFETY APPLICATIONS (NME TECHNOLOGY)VJ OMD Series ....................................................................................................................................................................... 66VJ HVArc Guard® ................................................................................................................................................................... 80VJ Source Energy Capacitor (SEC) ........................................................................................................................................ 88VJ Controlled Discharge Capacitor (CDC).............................................................................................................................. 93VJ Safety Certified Capacitors C0G (NP0).............................................................................................................................. 98VJ Safety Certified Capacitors X7R........................................................................................................................................ 102
MLCCs FOR RF AND HIGH FREQUENCY APPLICATIONSVJ HIFREQ Series................................................................................................................................................................... 107QUAD HIFREQ Series............................................................................................................................................................. 117VJ High Q ............................................................................................................................................................................... 130VJ....W1BC High Q Dielectric ................................................................................................................................................. 134VJ....W1BC Ultra High Q / Low ESR ...................................................................................................................................... 140
MLCCs FOR NON-MAGNETIC APPLICATIONS (NME TECHNOLOGY)VJ Non-Magnetic Series for IR Reflow Soldering.................................................................................................................... 147VJ Non-Magnetic Series for Epoxy Bonding .......................................................................................................................... 163
MLCCs FOR HIGH RELIABILITY AND MILITARY / AEROSPACE APPLICATIONS (NME TECHNOLOGY)VJ Hi-Rel Series...................................................................................................................................................................... 180CDR-MIL-PRF-55681 ............................................................................................................................................................. 194DSCC 03029........................................................................................................................................................................... 205DSCC 03028........................................................................................................................................................................... 209DSCC 05006........................................................................................................................................................................... 214DSCC 05007........................................................................................................................................................................... 218DSCC 05001........................................................................................................................................................................... 222DSCC 05002........................................................................................................................................................................... 226DSCC 05003........................................................................................................................................................................... 230
MLCCs FOR BASIC COMMODITY APPLICATIONS (BME TECHNOLOGY)VJ….W1BC Basic Commodity Series..................................................................................................................................... 235VJ….W1BC Ultra Small Series 0201 ...................................................................................................................................... 249VJ.…W1BC MLCC Chip Array ............................................................................................................................................... 254
RELATED DOCUMENTS AND REQUIREMENTSVJ Vitramon Packaging .......................................................................................................................................................... 260VJ Soldering Recommendations ............................................................................................................................................ 265VJ Marking Options ................................................................................................................................................................ 268Vishay Vitramon MLCC End Termination................................................................................................................................ 270VJ….W1BC Test Procedures and Requirements ................................................................................................................... 272VJ....W1BC Soldering and Footprint Design........................................................................................................................... 278
Multilayer Ceramic Chip Capacitorswww.vishay.com Vishay
Part Numbering / Ordering Information
Notes(1) For details see individual datasheets(2) Marking option is not available in process code W1BC(3) Chip array size 0612 including 4 capacitors VJ06C4...W1BC, only Basic Commodity Series(4) Termination code “E” for conductive epoxy assembly, contact [email protected] for availability(5) Case size designator may be replaced by a four digit drawing number(6) Customer specific process codes are also possible(7) For non-magnetic termination, “C” is recommended for solder assembly, and “N” for conductive epoxy assembly
PART NUMBERING / ORDERING INFORMATION (1)
VJ0805 Y 102 K X A A C 2L
CASE CODE (5) DIELECTRIC
CAPACITANCENOMINAL
CODE
TOLERANCE CODE TERMINATION VOLTAGE
RATINGMARKING OPTION (2) PACKAGING PROCESS
CODE (6)
0201 A =C0G (NP0)
Expressed inpicofarad (pF).
The firsttwo digits are
significant,the third isa multiplier.
An “R”indicatesa decimal
point.
Example:0R3 = 0.3 pF4R7 = 4.7 pF
102 = 1000 pF473 = 47 000 pF
V = ± 0.05 pFB = ± 0.10 pFC = ± 0.25 pF D = ± 0.50 pF
F = ± 1 % G = ± 2 %H = ± 3 %J = ± 5 %
K = ± 10 % M = ± 20 %
Z = -20 % / +80 %
X = Ni barrier100 % matte tin
plate finish
B = polymer100 % matte tin
plate finish
F, E = AgPd (4)
L = Ni barriertin / lead platemin. 4 % lead
N =non-magnetic (7)
C = copper barrier 100 % mattetin plate finish
(non-magnetic) (7)
Y = 6.3 VDC A = unmarked
M = markingvendor ID +2 charactercap. code
(size 0805 /1206 / 0505 /1111 / 2525 /
3838)
B = markingfor automotive
VJ....31 / VJ....31X
vendor ID +date code
(size 0805 / 1206)
S = markingfor safety caps
T = 7" reel /plastic tape
C = 7" reel /paper tape
O = 7" reel /flamed paper tape
used for AgPdtermination
0402 / 0603 / 0805
J = 7" reel (low quantity)
E = 7" reel /plastic tapeonly used
automotive VJ...31 / VJ...34
R =11 1/4" / 13" reel /
plastic tape
P =11 1/4" / 13" reel /
paper tape
I =11 1/4" / 13" reel /flamed paper tape
used for AgPd termination
0402 / 0603 / 0805
M =11 1/4" / 13" reel /
plastic tape only used
automotiveVJ...31 / VJ...34
00, 54 = standard
31, 34, 31X =automotive
4X, 5H =open mode
5Z =HVArcGuard®
X1, X2 =safety caps
SE = SourceEnergy
Capacitor(SEC)
8R =ControlledDischargeCapacitor
(CDC)
2L, 2M,68, 5G = high-rel.
W1BC = basic
commodity
0402 Q = 10 VDC
0505 Y = X7R J = 16 VDC
0603 G = X5R X = 25 VDC
06C4 (3) H = X8R Z = 35 VDC
0805 Q = high Q A = 50 VDC
1111 V = Y5V B = 100 VDC
1206L =
ultra high Qlow ESR
C = 200 VDC
1210 P = 250 VDC
1808 D = 300 VDC
1812 D = HIFREQ T = 400 VDC
1825 E = 500 VDC
2008 L = 630 VDC
2012 I = 800 VDC
2220 G = 1000 VDC
2225 R = 1500 VDC
2525 F = 2000 VDC
3040 O = 2500 VDC
3640 H = 3000 VDC
3838 W = 3600 VDC
4044 M = 5000 VDC
S = 7200 VDCS = 4 VDConly for
VJ...W1BC series
U = 250 VAC
Revision: 29-Oct-14 2 Document Number: 45067For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Multilayer Ceramic Chip Capacitorswww.vishay.com Vishay
Note• For details of ratings, see individual datasheet
Note• For details of ratings, see individual datasheet
Notes• For details of ratings, see individual datasheet• Contact [email protected] for availability
PART NUMBERING / ORDERING INFORMATION MILITARY PRODUCTSCDR31 BX 103 A K Z P A T
MILITARY STYLE DIELECTRIC CAPACITANCE
DC VOLTAGE RATING
TOLERANCE CODE TERMINATION FAILURE
RATEMARKING OPTION PACKAGING
CDR01CDR02CDR03CDR04CDR06CDR31CDR32CDR33CDR34
BPBX
Expressed in picofarad (pF).The first two
digits are significant, the
third is a multiplier.
An “R” indicates a decimal point.
Example:4R7 = 4.7 pF
102 = 1000 pF
A = 50 VB = 100 V
C = ± 0.25 pFD = ± 0.50 pF
F = ± 1 %J = ± 5 %
K = ± 10 %M = ± 20 %
M = silver palladium
Y = Ni barrier 100 % tin plate
matte finish
W = Ni barrier 100 % tin plate
matte finish
Z = Ni barrier 100 % tin / lead plate min. 4 %
U = hot solder dipped min.
4 % lead
M = 1.0 %P = 0.1 %
R = 0.01 %S = 0.001 %
Consult factury for failure rate
status
A = unmarked
T = 7" reel /plastic tape
J = 7" reel (low qty.)C = 7" reel /paper tape
R =11 1/4" / 13" reel /
plastic tapeP =
11 1/4" / 13" reel /paper tape
B = bulk
PART NUMBERING / ORDERING INFORMATION DSCC PRODUCTS03028- BX 102 A K Z C J
DSCC STYLE DIELECTRIC CAPACITANCE
DC VOLTAGE RATING
TOLERANCE CODE TERMINATION GROUP TESTING PACKAGING
03028-03029-05006-05007-
BPBXBR
Expressed in picofarad (pF).The first two
digits are significant, the
third is a multiplier.
An “R” indicates a decimal point.
Example:4R7 = 4.7 pF
102 = 1000 pF
X = 10 VY = 16 VZ = 25 VA = 50 V
B = 100 VC = 200 V
C = ± 0.25 pFD = ± 0.50 pF
F = ± 1 %G = ± 2 %J = ± 5 %
K = ± 10 %M = ± 20 %
M = silver palladium
Z = Ni barrier tin / lead plate
min. 4 % lead
U = hot solder dipped
min. 4 % lead
C = full group CL = 2000 h life test onlyM = 1000 h life test only
H = low voltagehumidity test only
- = group A test only
T = 7" reel /plastic tape
J = 7" reel (low qty.)C = 7" reel /paper tape
O = 7" reel /flamed paper tape
R = 11 1/4" / 13" reel /plastic tape
P = 11 1/4" / 13" reel /paper tape
I = 11 1/4" / 13" reel /flamed paper tape
B = bulk
PART NUMBERING / ORDERING INFORMATION DSCC PRODUCTS05001- 4R7 A C Z C J
DSCC STYLE CAPACITANCE
DC VOLTAGE RATING
TOLERANCE CODE TERMINATION GROUP TESTING PACKAGING
05001-05002-05003-
Expressed in picofarad (pF).The first two
digits are significant, the
third is a multiplier.
An “R” indicates a decimal point.
Example:4R7 = 4.7 pF
A = 50 VB = 100 VC = 200 VK = 250 V
B = ± 0.10 pFC = ± 0.25 pFD = ± 0.50 pF
F = ± 1 %G = ± 2 %J = ± 5 %
K = ± 10 %M = ± 20 %
M = silver palladium
Z = Ni barrier tin / lead plate
min. 4 % lead
C = full group CL = 2000 h life test onlyM = 1000 h life test only
H = low voltagehumidity test only
- = group A test only
T = 7" reel / plastic tapeJ = 7" reel (low qty.)
C = 7" reel / paper tapeO = 7" reel / flamed paper tape
R = 11 1/4" / 13" reel /plastic tape
P = 11 1/4" / 13" reel /paper tape
I = 11 1/4" / 13" reel /flamed paper tape
B = bulk
Revision: 29-Oct-14 3 Document Number: 45067For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Contents
VJ Commercial Series............ 5
MLCCsfor
Commercial
Applications
(NME Technology)
VJ Commercial Serieswww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitorsfor Commercial Applications
FEATURES• C0G (NP0) and X7R dielectrics offered• C0G (NP0) is an ultra-stable dielectric offering a
very low Temperature Coefficient of Capacitance(TCC)
• C0G (NP0) offers low dissipation• Excellent aging characteristics• Ideal for decoupling and filtering (X7R)• Ideal for surge suppression and high voltage
applications• Wide range of case sizes, voltage ratings and capacitance
values• Wet build process• Reliable Noble Metal Electrode (NME) system • Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS• Timing and tuning circuits• Sensor and scanner applications• Decoupling and filtering• Surge suppression
ELECTRICAL SPECIFICATIONS
Available
C0G (NP0) DIELECTRIC
GENERAL SPECIFICATIONNote Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +150 °C(above +125 °C changed characteristics)
Capacitance Range: 1 pF to 56 nF
Voltage Range: 25 VDC to 1000 VDC
Temperature Coefficient of Capacitance (TCC):0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
Dissipation Factor (DF):0.1 % maximum at 1.0 VRMS and 1 MHz for values 1000 pF0.1 % maximum at 1.0 VRMS and 1 kHz for values > 1000 pF
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 0 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 200 VDC-rated: 250 % of rated voltage500 VDC-rated: 200 % of rated voltage630 VDC,1000 VDC-rated: 150 % of rated voltage
X7R DIELECTRIC
GENERAL SPECIFICATIONNoteElectrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +150 °C(above +125 °C changed characteristics)
Capacitance Range: 120 pF to 6.8 μF
Voltage Range: 16 VDC to 1000 VDC
Temperature Coefficient of Capacitance (TCC):± 15 % from -55 °C to +125 °C, with 0 VDC applied
Dissipation Factor (DF):16 V / 25 V ratings: 3.5 % maximum at 1.0 VRMS and 1 kHz> 25 V ratings: 2.5 % maximum at 1.0 VRMS and 1 kHz
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 1 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 250 VDC-rated: 250 % of rated voltage500 VDC-rated: min. 150 % of rated voltage630 VDC, 1000 VDC-rated: min. 120 % of rated voltage
Revision: 09-Sep-14 5 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE (V)
CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0)
0402 100 1.0 pF 220 pF
0603 200 1.0 pF 1.0 nF
0805 500 1.0 pF 4.7 nF
1206 630 1.0 pF 10 nF
1210 630 56 pF 12 nF
1808 1000 18 pF 10 nF
1812 1000 39 pF 22 nF
1825 500 100 pF 39 nF
2220 1000 270 pF 47 nF
2225 1000 270 pF 56 nF
X7R
0402 100 120 pF 47 nF
0603 200 330 pF 150 nF
0805 250 330 pF 470 nF
1206 630 330 pF 1.0 μF
1210 630 390 pF 1.0 μF
1808 1000 470 pF 270 nF
1812 1000 1.0 nF 1.0 μF
1825 1000 10 nF 2.7 μF
2220 500 15 nF 2.2 μF
2225 1000 33 nF 4.7 μF
3640 500 27 nF 6.8 μF
Revision: 09-Sep-14 6 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
Notes(1) Case size designator may be replaced by four digit drawing number used to control non-standard products and / or special requirements(2) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected](3) Process code may be added with up to three digits, used to control non-standard products and / or special requirements(4) Termination code “E” is for conductive epoxy assembly(5) Selected values available, contact [email protected] for list of released ratings
ORDERING INFORMATIONVJ0805 (1) Y 102 K X A A T ### (3)
CASECODE
DIELECTRIC CAPACITANCENOMINAL CODE
CAPACITANCETOLERANCE
TERMINATION DCVOLTAGERATING (2)
MARKING PACKAGING PROCESSCODE
04020603080512061210180818121825222022253640
A = C0G(NP0)
Y = X7R
Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is amultiplier.
Examples:1R8 = 1.8 pF
102 = 1000 pF
B = ± 0.10 pFC = ± 0.25 pFD = ± 0.5 pF
F = ± 1 % G = ± 2 % J = ± 5 %
K = ± 10 %M = ± 20 %
NoteC0G (NP0):
B, C, D < 10 pFF, G, J, K 10 pF
X7R:J, K, M
X = Ni barrier100 % tin plated
matte finishF, E = AgPd (4)
B = polymer 100 % tin plated
matte finish (5)
J = 16 VX = 25 VA = 50 V
B = 100 VC = 200 VP = 250 VE = 500 VL = 630 V
G = 1000 V
A =unmarked
M = markedNote
Markingis only
available for0805 and1206 with
terminationcode “X” /
“B”
C = 7" reel / paper tapeT = 7" reel / plastic tape
P = 11 1/4"/13" reel / paper tape
R = 11 1/4"/13" reel / plastic tapeO = 7" reel /
flamed paper tapeI = 11 1/4" / 13"reel /
flamed paper tapeNote
“I” and “O” are used for“F”, “E” termination
size 0402 / 0603 / 0805
ENVIRONMENTAL STATUS
TERMINATION CODE TERMINATION DESCRIPTION RoHS COMPLIANT VISHAY GREEN
X Ni barrier 100 % tin plated matte finish Yes Yes
E AgPd Yes Yes
B Polymer layer, 100 % tin plated matte finish Yes No
F AgPd Yes No
Revision: 09-Sep-14 7 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
Note• Polymer (B-termination) have increased dimensions:
length 0.006"(0.15 mm)
DIMENSIONS in inches (millimeters)
CASE CODE STYLE LENGTH
(L) WIDTH
(W)
MAXIMUM THICKNESS
(T)
TERMINATION(P)
MINIMUM MAXIMUM
0402 VJ04020.040 + 0.004 / - 0.002
(1.00 + 0.10 / - 0.05)0.020 + 0.004 / - 0.002
(0.50 + 0.10 / - 0.05)0.024(0.60)
0.004(0.10)
0.016(0.41)
0603 VJ06030.063 ± 0.006(1.60 ± 0.15)
0.031 ± 0.006(0.80 ± 0.15)
0.038(0.97)
0.012(0.30)
0.018(0.46)
0805 VJ08050.079 ± 0.008 (2.00 ± 0.20)
0.049 ± 0.008 (1.25 ± 0.20)
0.057(1.45)
0.010(0.25)
0.028(0.71)
1206 VJ12060.126 ± 0.010(3.20 ± 0.25)
0.063 ± 0.010(1.60 ± 0.25)
0.067(1.70)
0.010(0.25)
0.028(0.71)
1210 VJ12100.126 ± 0.010(3.20 ± 0.25)
0.098 ± 0.010(2.50 ± 0.25)
0.067(1.70)
0.010(0.25)
0.028(0.71)
1808 VJ18080.180 ± 0.012(4.57 ± 0.30)
0.080 ± 0.010 (2.03 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
1812 VJ18120.177 ± 0.012 (4.50 ± 0.30)
0.126 ± 0.008 (3.20 ± 0.20)
0.086(2.18)
0.010(0.25)
0.030(0.76)
1825 VJ18250.177 ± 0.012 (4.50 ± 0.30)
0.252 ± 0.010 (6.40 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
2220 VJ22200.220 ± 0.010 (5.59 ± 0.25)
0.200 ± 0.010 (5.08 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
2225 VJ22250.220 ± 0.010 (5.59 ± 0.25)
0.250 ± 0.010 (6.35 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
3640 VJ36400.360 ± 0.015 (9.14 ± 0.38)
0.400 ± 0.015 (10.20 ± 0.38)
0.086(2.18)
0.010(0.25)
0.030(0.76)
L W
P
TMAX.
Revision: 09-Sep-14 8 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Paper tape • Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ0402 VJ0603 VJ0805 VJ1206 (1) VJ1210 (1)
CASE CODE 0402 0603 0805 1206 1210VOLTAGE (VDC) 25 50 100 50 100 200 50 100 200 500 50 100 200 500 630 50 100 200 500 630VOLTAGE CODE X A B A B C A B C E A B C E L A B C E LCAP. CODE CAP.1R0 1.0 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••1R2 1.2 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••1R5 1.5 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••1R8 1.8 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••2R2 2.2 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••2R7 2.7 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••3R3 3.3 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••3R9 3.9 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••4R7 4.7 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••5R6 5.6 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••6R8 6.8 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••8R2 8.2 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••100 10 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••120 12 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••150 15 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••180 18 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••220 22 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••270 27 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••330 33 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••390 39 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••470 47 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••560 56 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• • •680 68 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• • •820 82 pF •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• • •101 100 pF •• •• •• •• •• •• •• •• •• •• • • • • • • •121 120 pF •• •• •• •• •• •• •• •• •• •• • • • • • • • • • •151 150 pF •• •• •• •• •• •• •• •• •• • • • • • • • • • •181 180 pF •• •• •• •• • •• •• •• •• • • • • • • • • • •221 220 pF •• •• •• •• • •• •• •• • • • • • • • • • • •271 270 pF •• •• • •• •• •• • • • • • • • • • • •331 330 pF •• •• •• •• •• • • • • • • • • • • •391 390 pF •• •• •• •• •• • • • • • • • • • • •471 470 pF •• •• •• • • • • • • • • • • • •561 560 pF •• •• •• • • • • • • • • • • •681 680 pF •• •• •• • • • • • • • • • • •821 820 pF •• •• •• • • • • • • • • • • •102 1.0 nF •• •• •• • • • • • • • • • • •122 1.2 nF •• • • • • • • • • •152 1.5 nF •• • • • • • • • • •182 1.8 nF • • • • • • • • •222 2.2 nF • • • • • • •272 2.7 nF • • • • • • •332 3.3 nF • • • • • • •392 3.9 nF • • • • • •472 4.7 nF • • • • • •562 5.6 nF • • • • •682 6.8 nF • • • • •822 8.2 nF • • • • •103 10 nF • • • •123 12 nF • •153 15 nF183 18 nF223 22 nF273 27 nF333 33 nF393 39 nF473 47 nF563 56 nF
Revision: 09-Sep-14 9 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
• Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1808 (1) VJ1812 (1) VJ1825 (1)
CASE CODE 1808 1812 1825VOLTAGE (VDC) 50 100 200 500 1000 50 100 200 500 1000 50 100 200 500VOLTAGE CODE A B C E G A B C E G A B C ECAP. CODE CAP.1R0 1.0 pF1R2 1.2 pF1R5 1.5 pF1R8 1.8 pF2R2 2.2 pF2R7 2.7 pF3R3 3.3 pF3R9 3.9 pF4R7 4.7 pF5R6 5.6 pF6R8 6.8 pF8R2 8.2 pF100 10 pF120 12 pF150 15 pF180 18 pF •220 22 pF • •270 27 pF • •330 33 pF • •390 39 pF • • • • • • •470 47 pF • • • • • • •560 56 pF • • • • • • •680 68 pF • • • • • • •820 82 pF • • • • • • •101 100 pF • • • • • • • •121 120 pF • • • • • • • • •151 150 pF • • • • • • • • •181 180 pF • • • • • • • • •221 220 pF • • • • • • • • • • •271 270 pF • • • • • • • • • • •331 330 pF • • • • • • • • • • •391 390 pF • • • • • • • • • • •471 470 pF • • • • • • • • • • •561 560 pF • • • • • • • • • • •681 680 pF • • • • • • • • • • •821 820 pF • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • •332 3.3 nF • • • • • • • • • • •392 3.9 nF • • • • • • • • • • •472 4.7 nF • • • • • • • • • • •562 5.6 nF • • • • • • • • • • •682 6.8 nF • • • • • • • • • • •822 8.2 nF • • • • • • • • • •103 10 nF • • • • • • • • •123 12 nF • • • • • •153 15 nF • • • • •183 18 nF • • • •223 22 nF • • • •273 27 nF • • •333 33 nF • •393 39 nF •473 47 nF563 56 nF
Revision: 09-Sep-14 10 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
• Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ2220 (1) VJ2225 (1)
CASE CODE 2220 2225VOLTAGE (VDC) 50 100 200 500 630 1000 50 100 200 500 1000VOLTAGE CODE A B C E L G A B C E GCAP. CODE CAP.1R0 1.0 pF1R2 1.2 pF1R5 1.5 pF1R8 1.8 pF2R2 2.2 pF2R7 2.7 pF3R3 3.3 pF3R9 3.9 pF4R7 4.7 pF5R6 5.6 pF6R8 6.8 pF8R2 8.2 pF100 10 pF120 12 pF150 15 pF180 18 pF220 22 pF270 27 pF330 33 pF390 39 pF470 47 pF560 56 pF680 68 pF820 82 pF101 100 pF121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF • • • • • • •331 330 pF • • • • • • •391 390 pF • • • • • • •471 470 pF • • • • • • • •561 560 pF • • • • • • • •681 680 pF • • • • • • • •821 820 pF • • • • • • • •102 1.0 nF • • • • • • • • •122 1.2 nF • • • • • • • • • • •152 1.5 nF • • • • • • • • • • •182 1.8 nF • • • • • • • • • • •222 2.2 nF • • • • • • • • • • •272 2.7 nF • • • • • • • • • • •332 3.3 nF • • • • • • • • • • •392 3.9 nF • • • • • • • • • • •472 4.7 nF • • • • • • • • • •562 5.6 nF • • • • • • • • •682 6.8 nF • • • • • • •822 8.2 nF • • • • • • •103 10 nF • • • • • • •123 12 nF • • • • • • •153 15 nF • • • • • •183 18 nF • • • • •223 22 nF • • • • •273 27 nF • • • • •333 33 nF • • • • •393 39 nF • • • •473 47 nF • • •563 56 nF •
Revision: 09-Sep-14 11 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Paper tape • Plastic tape
SELECTION CHARTDIELECTRIC X7RSTYLE VJ0402 VJ0603 VJ0805CASE CODE 0402 0603 0805VOLTAGE (VDC) 16 25 50 100 16 25 50 100 200 16 25 50 100 200 250VOLTAGE CODE J X A B J X A B C J X A B C PCAP. CODE CAP.121 120 pF •• •• •• ••151 150 pF •• •• •• ••181 180 pF •• •• •• ••221 220 pF •• •• •• ••271 270 pF •• •• •• ••331 330 pF •• •• •• •• •• •• •• ••391 390 pF •• •• •• •• •• •• •• •• •• ••471 470 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••561 560 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••681 680 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••821 820 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••102 1.0 nF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••122 1.2 nF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••152 1.5 nF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••182 1.8 nF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••222 2.2 nF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••272 2.7 nF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••332 3.3 nF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••392 3.9 nF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••472 4.7 nF •• •• •• •• •• •• •• •• •• •• •• •• •• •• ••562 5.6 nF •• •• •• •• •• •• •• •• •• •• •• •• ••682 6.8 nF •• •• •• •• •• •• •• •• •• •• •• •• ••822 8.2 nF •• •• •• •• •• •• •• •• •• •• •• •• ••103 10 nF •• •• •• •• •• •• •• •• •• •• •• •• • 123 12 nF •• •• •• •• •• •• •• •• •• •• •• • 153 15 nF •• •• •• •• •• •• •• •• •• •• • • 183 18 nF •• •• •• •• •• •• •• •• •• •• • • 223 22 nF •• •• •• •• •• •• •• •• •• • • 273 27 nF •• •• •• •• •• •• •• •• •• • 333 33 nF •• •• •• •• •• •• •• •• • 393 39 nF •• •• •• •• •• •• •• •• • 473 47 nF •• •• •• •• •• •• •• • 563 56 nF •• •• •• •• •• •• • 683 68 nF •• •• •• •• •• • • 823 82 nF •• •• •• •• •• • • 104 100 nF •• •• •• •• •• • •124 120 nF •• •• •• • 154 150 nF •• • • • 184 180 nF • • 224 220 nF • • 274 270 nF • • 334 330 nF • • 394 390 nF • 474 470 nF • 564 560 nF684 680 nF824 820 nF105 1.0 μF125 1.2 μF155 1.5 μF185 1.8 μF225 2.2 μF275 2.7 μF335 3.3 μF395 3.9 μF475 4.7 μF565 5.6 μF685 6.8 μF
Revision: 09-Sep-14 12 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Paper tape • Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1206 (1) VJ1210 (1)
CASE CODE 1206 1210VOLTAGE (VDC) 16 25 50 100 200 250 500 630 16 25 50 100 200 250 500 630VOLTAGE CODE J X A B C P E L J X A B C P E LCAP. CODE CAP.121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF331 330 pF •• ••391 390 pF •• •• •471 470 pF •• •• •• •• •• •• •561 560 pF •• •• •• •• •• •• •681 680 pF •• •• •• •• •• •• •821 820 pF •• •• •• •• •• •• •102 1.0 nF •• •• •• •• •• •• •• • •122 1.2 nF •• •• •• •• •• •• •• • •152 1.5 nF •• •• •• •• •• •• •• • •182 1.8 nF •• •• •• •• •• •• •• • •222 2.2 nF •• •• •• •• •• •• •• • •272 2.7 nF •• •• •• •• •• •• •• • •332 3.3 nF •• •• •• •• •• •• •• • • •392 3.9 nF •• •• •• •• •• •• •• • • •472 4.7 nF •• •• •• •• •• •• •• • • •562 5.6 nF •• •• •• •• •• • • • • •682 6.8 nF •• •• •• •• •• • • • • •822 8.2 nF •• •• •• •• •• • • • • •103 10 nF •• •• •• •• •• • • • • • • • • • •123 12 nF •• •• •• •• •• • • • • • • • • • •153 15 nF •• •• •• •• •• • • • • • • • • • •183 18 nF •• •• •• •• •• • • • • • • • • • •223 22 nF •• •• •• •• •• • • • • • • • •273 27 nF •• •• •• •• •• • • • • • • • •333 33 nF •• •• •• •• •• • • • • • • • • •393 39 nF •• •• •• •• • • • • • • • • • •473 47 nF •• •• •• •• • • • • • • • • • •563 56 nF •• •• •• •• • • • • • • • •683 68 nF •• •• •• •• • • • • • • • •823 82 nF •• •• • • • • • • • • • •104 100 nF •• •• • • • • • • • • • •124 120 nF •• •• • • • • • • •154 150 nF •• •• • • • • • • •184 180 nF •• •• • • • • • • •224 220 nF • • • • • • • •274 270 nF • • • • • • • •334 330 nF • • • • • • •394 390 nF • • • • • • •474 470 nF • • • • • • •564 560 nF • • • • •684 680 nF • • • • •824 820 nF • • • • •105 1.0 μF • • • • •125 1.2 μF155 1.5 μF185 1.8 μF225 2.2 μF275 2.7 μF335 3.3 μF395 3.9 μF475 4.7 μF565 5.6 μF685 6.8 μF
Revision: 09-Sep-14 13 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
• Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1808 (1) VJ1812 (1) VJ1825 (1)
CASE CODE 1808 1812 1825VOLTAGE (VDC) 50 100 200 500 1000 25 50 100 200 250 500 630 1000 25 50 100 200 250 500 1000VOLTAGE CODE A B C E G X A B C P E L G X A B C P E GCAP. CODE CAP. 121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF331 330 pF391 390 pF471 470 pF •561 560 pF •681 680 pF •821 820 pF •102 1.0 nF • • • • •122 1.2 nF • • • • •152 1.5 nF • • • • •182 1.8 nF • • • • •222 2.2 nF • • • • •272 2.7 nF • • • • •332 3.3 nF • • • • •392 3.9 nF • • • • •472 4.7 nF • • • • • •562 5.6 nF • • • • • •682 6.8 nF • • • • • •822 8.2 nF • • • • • •103 10 nF • • • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • • • • • •393 39 nF • • • • • • • • • • • • • • • •473 47 nF • • • • • • • • • • • • • • • •563 56 nF • • • • • • • • • • • • • • • •683 68 nF • • • • • • • • • • • • • • •823 82 nF • • • • • • • • • • • • • • •104 100 nF • • • • • • • • • • • • • • • •124 120 nF • • • • • • • • • • • • •154 150 nF • • • • • • • • • • • • •184 180 nF • • • • • • • • • • • • •224 220 nF • • • • • • • • • • •274 270 nF • • • • • • • • • • •334 330 nF • • • • • • • • • •394 390 nF • • • • • • • • •474 470 nF • • • • • • • • •564 560 nF • • • • • • • •684 680 nF • • • • • • • •824 820 nF • • • • • • • •105 1.0 μF • • • • • • •125 1.2 μF • • •155 1.5 μF • • •185 1.8 μF • •225 2.2 μF •275 2.7 μF •335 3.3 μF395 3.9 μF475 4.7 μF565 5.6 μF685 6.8 μF
Revision: 09-Sep-14 14 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
• Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC X7RSTYLE VJ2220 (1) VJ2225 (1) VJ3640 (1)
CASE CODE 2220 2225 3640VOLTAGE (VDC) 50 100 200 500 25 50 100 200 500 1000 25 50 100 200 500VOLTAGE CODE A B C E X A B C E G X A B C ECAP. CODE CAP. 121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF331 330 pF391 390 pF471 470 pF561 560 pF681 680 pF821 820 pF102 1.0 nF122 1.2 nF152 1.5 nF182 1.8 nF222 2.2 nF272 2.7 nF332 3.3 nF392 3.9 nF472 4.7 nF562 5.6 nF682 6.8 nF822 8.2 nF103 10 nF123 12 nF153 15 nF •183 18 nF •223 22 nF •273 27 nF • • •333 33 nF • • • • • • • • •393 39 nF • • • • • • • • •473 47 nF • • • • • • • • •563 56 nF • • • • • • • • •683 68 nF • • • • • • • • •823 82 nF • • • • • • • • •104 100 nF • • • • • • • • • •124 120 nF • • • • • • • • •154 150 nF • • • • • • • • •184 180 nF • • • • • • • • • • • •224 220 nF • • • • • • • • • • • • •274 270 nF • • • • • • • • • • • • •334 330 nF • • • • • • • • • • • • •394 390 nF • • • • • • • • • • • •474 470 nF • • • • • • • • • • • •564 560 nF • • • • • • • • • • • •684 680 nF • • • • • • • • • • • •824 820 nF • • • • • • • • • • •105 1.0 μF • • • • • • • • • • •125 1.2 μF • • • • • • • • • •155 1.5 μF • • • • • • • •185 1.8 μF • • • • • • • •225 2.2 μF • • • • • •275 2.7 μF • • • • •335 3.3 μF • • • •395 3.9 μF • • • •475 4.7 μF • • •565 5.6 μF •685 6.8 μF •
Revision: 09-Sep-14 15 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
C0G (NP0) DIELECTRIC - TYPICAL PARAMETERS
- 75 - 50 - 25 0 50 100 125
2.0
1.5
1.0
0.5
0.0
- 0.5
- 1.0
- 1.5
- 2.0
NP0
TEMPERATURE °C 150 175 25 75
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE COEFFICIENT OF CAPACITANCE
TEMPERATURE °C
INSULATION RESISTANCE VS. TEMPERATURE
10 25 100 150
10 000
1000
100
1050
INS
UL
AT
ION
RE
SIS
TAN
CE
(ΩF
)AGING RATE
HOURS100 1000 10 000
% C
APA
CIT
AN
CE
CH
AN
GE
0.2
0.1
0.0
- 0.1
- 0.2
1 10
0.2
0.1
0.0
- 0.1
- 0.2
DC VOLTS APPLIED
VOLTAGE COEFFICIENT OF CAPACITANCE%
CA
PAC
ITA
NC
E C
HA
NG
E
0 10 20 30 40 50 60 70 80 90 100
CHANGE OF CAPACITANCE WITH FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
2
1
0
- 1
- 2
% C
APA
CIT
AN
CE
CH
AN
GE
DISSIPATION FACTOR VS. FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
0.00025
DIS
SIP
AT
ION
FA
CT
OR
0.0005
0.001
Revision: 09-Sep-14 16 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
X7R DIELECTRIC - TYPICAL PARAMETERS
15
10
5
0
- 5
- 10
- 15
- 20
TEMPERATURE °C
% C
AP
AC
ITA
NC
E C
HA
NG
E
- 25
- 30
TEMPERATURE COEFFICIENT OF CAPACITANCE
- 75 - 50 - 25 0 20 50 75 100 125 150 175 10 25 100
10 000
1000
100
10
INS
UL
AT
ION
RE
SIS
TA
NC
E(Ω
F)
150
INSULATION RESISTANCE VS. TEMPERATURE
TEMPERATURE °C
0.0
DISSIPATION FACTOR VS. TEMPERATURE
TEMPERATURE °C
% D
ISS
IPA
TIO
N F
AC
TO
R
0.51.01.52.02.53.03.54.04.55.05.56.0
- 75 - 50 - 25 0 25 50 75 100 125 150 175HOURS
1.0
0.0
- 1.0
- 2.0%
CA
PA
CIT
AN
CE
CH
AN
GE
- 3.0
- 4.0
AGING RATE
1 10 100 1000 10 000
100
50
TEMPERATURE °C
% R
AT
ED
VO
LT
AG
E
0
RATED VOLTAGE VS. TEMPERATURE
150
200
- 75 - 50 - 25 0 20 50 75 100 125 150 175 180 0 10 20 30 40 50 60 70 80 90 100
0
- 15
- 20
- 25
- 30
- 10
- 5
5
25 VRATED 50 V
100 V
VOLTAGE COEFFICIENT OF CAPACITANCE
DC VOLTS APPLIED
% C
APA
CIT
AN
CE
CH
AN
GE
RATED
RATED
0.020
0.016
0.012
0.008
0.004
DISSIPATION FACTOR VS. VOLTAGE
50 V100 V
DC VOLTS APPLIED
DIS
SIP
AT
ION
FA
CT
OR
0 10 20 30 40 50 60 70 80 90 100
DISSIPATION FACTOR VS. VOLTAGE
0 100 200 300 400 500 600 700
0.020
0.016
0.012
0.008
0.000500 V/630 V
200 V
DC VOLTS APPLIED
DIS
SIP
AT
ION
FA
CT
OR
Revision: 09-Sep-14 17 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Commercial Serieswww.vishay.com Vishay Vitramon
Notes(1) Vishay Vitramon uses embossed plastic carrier tape(2) REFERENCE: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(3) n/a = not available(4) Packaging “C” / “P” / “O” / “I” and “T” / “R” or lower quantities can depend from product thickness
STANDARD PACKAGING QUANTITIES (1)(2)(3)
CASE CODE TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PAPER TAPE PACKAGING CODE
“C” / “O”
PLASTIC TAPE PACKAGING CODE
“T”
PAPER TAPE PACKAGING CODE
“P” / “I”
PLASTIC TAPE PACKAGING CODE
“R”
0402 8 mm 5000 n/a 10 000 n/a
0603 (4) 8 mm 4000 4000 10 000 10 000
0805 (4) 8 mm 3000 3000 10 000 10 000
1206 (4) 8 mm 3000 2500 / 3000 10 000 9000 / 10 000
1210 (4) 8 mm n/a 2000 / 2500 / 3000 n/a 9000 / 10 000
1808 12 mm n/a 2000 n/a 10 000
1812 12 mm n/a 1000 n/a 4000
1825 12 mm n/a 1000 n/a 4000
2220 12 mm n/a 1000 n/a 4000
2225 12 mm n/a 1000 n/a 4000
3640 16 mm n/a 500 n/a n/a
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to 40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 09-Sep-14 18 Document Number: 45199For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Contents
VJ X8R ................................... 20
MLCCsfor
High Temperature
Applications
(NME Technology)
VJ X8Rwww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitorsfor High Temperature Applications
FEATURES• Specialty: high temperature applications
• High operating temperature dielectric,up to +150 °C
• Maintains capacitance at high temperature forfrequency stability
• Wet build process
• Reliable Noble Metal Electrode (NME) system
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
APPLICATIONS• High temperature modules
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at +25 °C unless otherwise specified.
Operating Temperature: -55 °C to +150 °C
Capacitance Range: 330 pF to 220 nF
Voltage Range: 25 VDC to 100 VDC
Temperature Coefficient of Capacitance (TCC): ± 15 % from -55 °C to +150 °C
Dissipation Factor (DF): 25 V ratings: 3.5 % maximum at 1.0 VRMS and 1 kHz> 25 V ratings: 2.5 % maximum at 1.0 VRMS and 1 kHz
Aging Rate: 1 % maximum per decade
Insulation Resistance (IR): at +25 °C and rated voltage 100 000 M minimum or1000 F, whichever is lessat +125 °C and rated voltage 10 000 M minimum or100 F, whichever is less
Dielectric Strength Test:performed per method 103 of EIA-198-2-E Applied test voltage: 100 VDC-rated: 250 % of rated voltage
Available
Revision: 26-Aug-14 20 Document Number: 45006For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ X8Rwww.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
Notes(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected](2) Process code may be added with up to three digits, used to control non-standard products and requirements.(3) Termination code “E” for conductive epoxy assembly.(4) Marking in reference to EIA198, see www.vishay.com/doc?45028(5) Termination code “F” not available for 0402, 0603 - 100 V, 0805 - 100 V.
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE(V)
CAPACITANCE
MINIMUM MAXIMUM
X8R
0402 100 330 pF 6.8 nF
0603 100 470 pF 33 nF
0805 100 470 pF 100 nF
1206 50 1.0 nF 220 nF
1210 50 10 nF 220 nF
ORDERING INFORMATIONVJ0805 H 102 K X A A C ### (2)
CASECODE
DIELECTRIC CAPACITANCENOMINAL
CODE
CAPACITANCETOLERANCE
TERMINATION DC VOLTAGERATING (1)
MARKING (4) PACKAGING PROCESSCODE
04020603080512061210
H = X8R Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is amultiplier.
Examples:102 = 1000 pF
J = ± 5 %K = ± 10 %M = ± 20 %
X = Ni barrier100 % tin platedF, E = AgPd (3)(5)
X = 25 VA = 50 V
B = 100 V
A = unmarkedM = marked
NoteMarking is only
available for0805 and 1206with termination
code “X”
T = 7" reel / plastic tapeC = 7" reel / paper tape
R = 11 1/4" / 13" reel / plastic tapeP = 11 1/4" / 13" reel / paper tape
O = 7" reel / flamed paper tapeI = 11 1/4" / 13" reel / flamed paper tape
Note“I” and “O” are used for
“F” termination size 0603 / 0805 and“E” termination size 0402 / 0603 / 0805
ENVIRONMENTAL STATUSTERMINATION CODE TERMINATION DESCRIPTION RoHS COMPLIANT VISHAY GREEN
X Ni barrier 100 % tin plated matte finish Yes Yes
E AgPd Yes Yes
F AgPd Yes No
Revision: 26-Aug-14 21 Document Number: 45006For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ X8Rwww.vishay.com Vishay Vitramon
DIMENSIONS in inches (millimeters)
CASECODE STYLE LENGTH
(L)WIDTH
(W)MAXIMUM THICKNESS
(T)
TERMINATION(P)
MINIMUM MAXIMUM
0402 VJ04020.040 + 0.004/- 0.002
(1.00 + 0.10/- 0.05)0.020 + 0.004/- 0.002
(0.50 + 0.10/- 0.05)0.024(0.60)
0.004(0.10)
0.016(0.41)
0603 VJ06030.063 ± 0.006(1.60 ± 0.15)
0.031 ± 0.006(0.80 ± 0.15)
0.036(0.92)
0.012 (0.30)
0.018 (0.46)
0805 VJ08050.079 ± 0.008 (2.00 ± 0.20)
0.049 ± 0.008(1.25 ± 0.20)
0.057(1.45)
0.010(0.25)
0.028 (0.71)
1206 VJ12060.126 ± 0.010(3.20 ± 0.25)
0.063 ± 0.010(1.60 ± 0.25)
0.067(1.70)
0.010(0.25)
0.028 (0.71)
1210 VJ12100.126 ± 0.010(3.20 ± 0.25)
0.098 ± 0.010(2.50 ± 0.25)
0.067(1.70)
0.010(0.25)
0.028 (0.71)
LW
T
MAX.
P
Revision: 26-Aug-14 22 Document Number: 45006For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ X8Rwww.vishay.com Vishay Vitramon
Notes(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034• Plastic tape, •• Paper tape
RoHS-compliant
Notes(1) Reference: EIA standard RS481 - “Taping of Surface Mount Components for Automatic Placement”(2) Packaging “C” / “P” / “O” / “I” and “T” / “R” or lower quantities can depend from product thickness
SELECTION CHARTDIELECTRIC X8RSTYLE VJ0402 VJ0603 VJ0805 VJ1206 (1) VJ1210 (1)
CASE CODE 0402 0603 0805 1206 1210VOLTAGE (VDC) 25 50 100 25 50 100 25 50 100 25 50 25 50VOLTAGE CODE X A B X A B X A B X A X ACAP. CODE CAP.
331 330 pF •• •• ••391 390 pF •• •• ••471 470 pF •• •• •• •• •• •• •• ••561 560 pF •• •• •• •• •• •• •• ••681 680 pF •• •• •• •• •• •• •• •• ••821 820 pF •• •• •• •• •• •• •• •• ••102 1.0 nF •• •• •• •• •• •• •• •• •• • •122 1.2 nF •• •• •• •• •• •• •• •• •• • •152 1.5 nF •• •• •• •• •• •• •• •• • •182 1.8 nF •• •• •• •• •• •• •• •• • •222 2.2 nF •• •• •• •• •• •• •• •• • •272 2.7 nF •• •• •• •• •• •• •• • •332 3.3 nF •• •• •• •• •• •• •• • •392 3.9 nF •• •• •• •• •• •• •• • •472 4.7 nF •• •• •• •• •• •• •• • •562 5.6 nF •• •• •• •• •• •• • •682 6.8 nF •• •• •• •• •• •• • •822 8.2 nF •• •• •• •• •• • •103 10 nF •• •• •• •• •• • • • •123 12 nF •• •• •• •• •• • • • •153 15 nF •• •• •• •• •• • • • •183 18 nF •• •• •• •• •• • • • •223 22 nF •• •• •• • • • • •273 27 nF •• •• • • • • • •333 33 nF •• •• • • • • •393 39 nF •• • • • • •473 47 nF • • • • • •563 56 nF • • • • • •683 68 nF • • • • •823 82 nF • • • • •104 100 nF • • • • •124 120 nF • • • •154 150 nF • • •184 180 nF • •224 220 nF • •274 270 nF334 330 nF394 390 nF
X8R PACKAGING QUANTITIES (1)
CASE CODE TAPE SIZE7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIESPACKAGING CODE PACKAGING CODE
“C” / “O” “T” “P” / “I” “R”0402 8 mm 5000 n/a 10 000 n/a0603 8 mm 4000 n/a 10 000 n/a
0805 (2) 8 mm 3000 3000 10 000 10 0001206 (2) 8 mm n/a 2500 / 3000 10 000 9000 / 10 0001210 (2) 8 mm n/a 2000 / 2500 / 3000 10 000 9000 / 10 000
Revision: 26-Aug-14 23 Document Number: 45006For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ X8Rwww.vishay.com Vishay Vitramon
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to 40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
X8R DIELECTRIC - TYPICAL PARAMETERS
- 75 - 50 - 25 0 25 50 75 100 125
15
10
5
0
- 5
- 10
- 15
- 20
TEMPERATURE °C
150 175
TEMPERATURE COEFFICIENT OF CAPACITANCE
% C
APA
CIT
AN
CE
CH
AN
GE
AGING RATE
HOURS
1.0
0.0
- 1.0
- 2.0%
CA
PA
CIT
AN
CE
CH
AN
GE
- 3.0
- 4.0
1 10 100 1000 10 000
DISSIPATION FACTOR VS. VOLTAGE
DIS
SIP
AT
ION
FA
CT
OR
DC VOLTS APPLIED
0.025
0.023
0.021
0.019
0.017
0.015
0.013
0 10 20 30 40 50 - 75 - 50 - 25 0 25 50 75 100 1250.0
DISSIPATION FACTOR VS. TEMPERATURE
TEMPERATURE °C
% D
ISS
IPA
TIO
N F
AC
TO
R
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
X8R
150 175
VOLTAGE COEFFICIENT OF CAPACITANCE
CA
PAC
ITA
NC
E C
HA
NG
E IN
%
DC VOLTS APPLIED
0.0
- 5.0
- 10.0
- 20.0
- 15.0
- 25.0
0 10 20 30 40 50 10 25 100
10 000
1000
100
10
INSU
LATI
ON
RES
ISTA
NC
E(Ω
F)
150
INSULATION RESISTANCE VS. TEMPERATURE
TEMPERATURE °C
Revision: 26-Aug-14 24 Document Number: 45006For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Contents
VJ....31X RoHSAutomotive MLCCs................ 26
VJ....31 / VJ....34Automotive MLCCs................ 45
MLCCsfor
Automotive
Applications
(NME Technology)
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitorsfor Automotive Applications
FEATURES
• AEC-Q200 qualified with PPAP available
• Available in 0402 to 1812 body size
• High operating temperature
• Wet build process
• Reliable Noble Metal Electrode (NME) system
• Parts compliant with ELV directive
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
For more than 25 years Vishay Vitramon has supported the automotive industry with robust, highly reliable MLCCs that havemade it a leader in this segment. All Vishay Vitramon MLCCs are manufactured in “Precious Metal Technology” (PMT / NME)and a wet build process. They are qualified according to AEC-Q200 with PPAP available on request. Applications for thesedevices include automotive “under the hood”, safety and comfort electronics. Their termination finish is 100 % matte tin platefinish. A polymer (flexible) termination with 100 % matte tin plate finish is offered for boardflex sensitive applications.
C0G (NP0) DIELECTRIC
GENERAL SPECIFICATIONNoteElectrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +150 °C (above +125 °C changed characteristics, see 2.2)
Capacitance Range: 1 pF to 22 nF
Voltage Range: 25 VDC to 3000 VDC
Temperature Coefficient of Capacitance (TCC):0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
Dissipation Factor (DF):0.1 % maximum at 1.0 VRMS and1 MHz for values 1000 pF0.1 % maximum at 1.0 VRMS and 1 kHz for values > 1000 pF
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging: 0 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 250 VDC-rated: 250 % of rated voltage500 VDC-rated: 200 % of rated voltage630 VDC, 1000 VDC-rated: 150 % of rated voltage3000 VDC-rated: 120 % of rated voltage
X7R, X8R DIELECTRIC
GENERAL SPECIFICATIONNoteElectrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +150 °C (X7R above +125 °C changed characteristics, see 2.2)
Capacitance Range: 120 pF to 1.0 μF
Voltage Range: 16 VDC to 1000 VDC
Temperature Coefficient of Capacitance (TCC):X7R: ± 15 % from -55 °C to +125 °C, with 0 VDC appliedX8R: ± 15 % from -55 °C to +150 °C, with 0 VDC applied
Dissipation Factor (DF):16 V, 25 V ratings: 3.5 % maximum at 1.0 VRMS and 1 kHz > 25 V ratings: 2.5 % maximum at 1.0 VRMS and 1 kHz
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 1 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 250 VDC-rated: 250 % of rated voltage500 VDC-rated: min. 150 % of rated voltage630 VDC, 1000 VDC-rated: min. 120 % of rated voltage
Revision: 06-Nov-14 26 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
QUICK REFERENCE DATA
DIELECTRIC CASE CODE MAXIMUM VOLTAGE (V)
CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0)
0402 100 1.0 pF 220 pF
0603 200 1.0 pF 1.0 nF
0805 500 1.0 pF 3.9 nF
1206 630 1.0 pF 10 nF
1210 630 100 pF 12 nF
1812 3000 12 pF 22 nF
X7R
0402 100 120 pF 47 nF
0603 200 330 pF 150 nF
0805 250 330 pF 470 nF
1206 1000 220 pF 1.0 μF
1210 630 390 pF 1.0 μF
1812 630 10 nF 1.0 μF
X8R
0402 100 330 pF 6.8 nF
0603 100 470 pF 33 nF
0805 100 470 pF 100 nF
1206 50 1.0 nF 220 nF
1210 50 10 nF 220 nF
Revision: 06-Nov-14 27 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
Notes(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected](2) Polymer termination contact [email protected] for availability of ratings(3) No marking on 1206 size - 1000 V
Note• Polymer (B-termination) have increased dimensions:
part length increased by 0.006" (0.15 mm)
ORDERING INFORMATION - TIN TERMINATIONVJ0805 Y 102 K X A B C 31X
CASECODE
DIELECTRIC CAPACITANCENOMINAL
CODE
CAPACITANCETOLERANCE
TERMINATION DC VOLTAGERATING (1)
MARKING (3) PACKAGING PROCESSCODE
040206030805120612101812
A = C0G(NP0)
Y = X7RH = X8R
Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is a
multiplier. An“R” indicates adecimal point.
Examples4R7 = 4.7 pF
102 = 1000 pF
B = ± 0.10 pFC = ± 0.25 pF D = ± 0.5 pF
F = ± 1 % G = ± 2 % J = ± 5 %
K = ± 10 %M = ± 20 %
NoteC0G (NP0):
B, C, D < 10 pFF, G, J, K 10 pF
X7R / X8R:J, K, M
X = Ni barrier100 % matte tin
plate finishB = polymer
100 % matte tin plate finish (2)
J = 16 VX = 25 VA = 50 V
B = 100 VC = 200 VP = 250 VE = 500 VL = 630 V
G = 1000 VH = 3000 V
A = unmarkedB = marked
NoteMarking for
0805 and 1206vendor ID and
date code
31X =Automotive
MLCCRoHS
conform
T = 7" reel / plastic tapeC = 7" reel / paper tape
R = 11 1/4" / 13" reel / plastic tapeP = 11 1/4" / 13" reel / paper tape
DIMENSIONS in inches (millimeters)
CASE CODE STYLE LENGTH
(L)WIDTH
(W)
MAXIMUM THICKNESS
(T)
TERMINATIONS PAD (P)
MINIMUM MAXIMUM
0402 VJ0402 0.040 + 0.004 / - 0.002(1.00 + 0.10 / - 0.05)
0.020 + 0.004 / - 0.002(0.50 + 0.10 / - 0.05)
0.024(0.60)
0.004(0.10)
0.016(0.41)
0603 VJ0603 0.063 ± 0.006(1.60 ± 0.15)
0.031 ± 0.006(0.80 ± 0.15)
0.038(0.97)
0.012(0.30)
0.018(0.46)
0805 VJ0805 0.079 ± 0.008(2.00 ± 0.20)
0.049 ± 0.008(1.25 ± 0.20)
0.057(1.45)
0.010(0.25)
0.028(0.71)
1206 VJ1206 0.126 ± 0.010(3.20 ± 0.25)
0.063 ± 0.010(1.60 ± 0.25)
0.067(1.70)
0.010(0.25)
0.028(0.71)
1210 VJ1210 0.126 ± 0.010(3.20 ± 0.25)
0.098 ± 0.010(2.50 ± 0.25)
0.076(1.94)
0.010(0.25)
0.028(0.71)
1812 VJ1812 0.177 ± 0.010(4.50 ± 0.25)
0.126 ± 0.010(3.20 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
L W
P
TMAX.
Revision: 06-Nov-14 28 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
Note•• Paper tape, • Plastic tape
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ0402 VJ0603 VJ0805CASE CODE 0402 0603 0805VOLTAGE (VDC) 25 50 100 50 100 200 50 100 200 500VOLTAGE CODE X A B A B C A B C ECAP. CODE CAP.
1R0 1.0 pF •• •• •• •• •• •• •• •• •• ••1R2 1.2 pF •• •• •• •• •• •• •• •• •• ••1R5 1.5 pF •• •• •• •• •• •• •• •• •• ••1R8 1.8 pF •• •• •• •• •• •• •• •• •• ••2R2 2.2 pF •• •• •• •• •• •• •• •• •• ••2R7 2.7 pF •• •• •• •• •• •• •• •• •• ••3R3 3.3 pF •• •• •• •• •• •• •• •• •• ••3R9 3.9 pF •• •• •• •• •• •• •• •• •• ••4R7 4.7 pF •• •• •• •• •• •• •• •• •• ••5R6 5.6 pF •• •• •• •• •• •• •• •• •• ••6R8 6.8 pF •• •• •• •• •• •• •• •• •• ••8R2 8.2 pF •• •• •• •• •• •• •• •• •• ••100 10 pF •• •• •• •• •• •• •• •• •• ••120 12 pF •• •• •• •• •• •• •• •• •• ••150 15 pF •• •• •• •• •• •• •• •• •• ••180 18 pF •• •• •• •• •• •• •• •• •• ••220 22 pF •• •• •• •• •• •• •• •• •• ••270 27 pF •• •• •• •• •• •• •• •• •• ••330 33 pF •• •• •• •• •• •• •• •• •• ••390 39 pF •• •• •• •• •• •• •• •• •• ••470 47 pF •• •• •• •• •• •• •• •• •• ••560 56 pF •• •• •• •• •• •• •• •• •• ••680 68 pF •• •• •• •• •• •• •• •• •• ••820 82 pF •• •• •• •• •• •• •• •• •• ••101 100 pF •• •• •• •• •• •• •• •• •• ••121 120 pF •• •• •• •• •• •• •• •• •• ••151 150 pF •• •• •• •• •• •• •• •• ••181 180 pF •• •• •• •• • •• •• •• ••221 220 pF •• •• •• •• • •• •• •• •271 270 pF •• •• • •• •• •• •331 330 pF •• •• •• •• •• •391 390 pF •• •• •• •• •• •471 470 pF •• •• •• •• • •561 560 pF •• •• •• •681 680 pF •• •• •• •821 820 pF •• •• •• •102 1.0 nF •• •• •• •122 1.2 nF •• •152 1.5 nF •• •182 1.8 nF • •222 2.2 nF •272 2.7 nF •332 3.3 nF •392 3.9 nF •472 4.7 nF562 5.6 nF682 6.8 nF822 8.2 nF103 10 nF123 12 nF153 15 nF183 18 nF223 22 nF273 27 nF333 33 nF393 39 nF473 47 nF 563 56 nF
Revision: 06-Nov-14 29 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
Notes•• Paper tape, • Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1206 VJ1210 (1) VJ1812 (1)
CASE CODE 1206 1210 1812VOLTAGE (VDC) 50 100 200 250 500 630 50 100 200 500 630 50 100 200 500 630 1000 3000VOLTAGE CODE A B C P E L A B C E L A B C E L G HCAP. CODE CAP.
1R0 1.0 pF •• •• •• •• ••1R2 1.2 pF •• •• •• •• ••1R5 1.5 pF •• •• •• •• ••1R8 1.8 pF •• •• •• •• ••2R2 2.2 pF •• •• •• •• ••2R7 2.7 pF •• •• •• •• ••3R3 3.3 pF •• •• •• •• ••3R9 3.9 pF •• •• •• •• ••4R7 4.7 pF •• •• •• •• ••5R6 5.6 pF •• •• •• •• ••6R8 6.8 pF •• •• •• •• ••8R2 8.2 pF •• •• •• •• ••100 10 pF •• •• •• •• ••120 12 pF •• •• •• •• •• •150 15 pF •• •• •• •• •• •180 18 pF •• •• •• •• •• •220 22 pF •• •• •• •• •• • •270 27 pF •• •• •• •• •• • •330 33 pF •• •• •• •• •• • •390 39 pF •• •• •• •• •• • • • • • • •470 47 pF •• •• •• •• •• • • • • • • •560 56 pF •• •• •• •• •• • • • • • • •680 68 pF •• •• •• •• •• • • • • • • •820 82 pF •• •• •• •• •• • • • • • • •101 100 pF • • • • • • • • • • • • • • • • •121 120 pF • • • • • • • • • • • • • • • •151 150 pF • • • • • • • • • • • • • • • •181 180 pF • • • • • • • • • • • • • • • •221 220 pF • • • • • • • • • • • • • • • •271 270 pF • • • • • • • • • • • • • • • •331 330 pF • • • • • • • • • • • • • • • •391 390 pF • • • • • • • • • • • • • • • •471 470 pF • • • • • • • • • • • • • • • •561 560 pF • • • • • • • • • • • • • • • •681 680 pF • • • • • • • • • • • • • • • •821 820 pF • • • • • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • •332 3.3 nF • • • • • • • • • • •392 3.9 nF • • • • • • • • • •472 4.7 nF • • • • • • • • • •562 5.6 nF • • • • • • • •682 6.8 nF • • • • • • • •822 8.2 nF • • • • • • • •103 10 nF • • • • • • •123 12 nF • • • • •153 15 nF • •183 18 nF •223 22 nF •273 27 nF333 33 nF393 39 nF473 47 nF 563 56 nF
Revision: 06-Nov-14 30 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
Note•• Paper tape, • Plastic tape
SELECTION CHARTDIELECTRIC X7RSTYLE VJ0402 VJ0603 VJ0805CASE CODE 0402 0603 0805VOLTAGE (VDC) 16 25 50 100 16 25 50 100 200 16 25 50 100 200 250VOLTAGE CODE J X A B J X A B C J X A B C PCAP. CODE CAP.
121 120 pF •• •• •• ••151 150 pF •• •• •• ••181 180 pF •• •• •• ••221 220 pF •• •• •• ••271 270 pF •• •• •• ••331 330 pF •• •• •• •• •• •• •• •• •• •• •• ••391 390 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••471 470 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••561 560 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••681 680 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••821 820 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••102 1.0 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••122 1.2 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••152 1.5 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••182 1.8 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••222 2.2 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••272 2.7 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••332 3.3 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••392 3.9 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••472 4.7 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••562 5.6 nF •• •• •• •• •• •• •• •• •• •• •• ••682 6.8 nF •• •• •• •• •• •• •• •• •• •• •• ••822 8.2 nF •• •• •• •• •• •• •• •• •• •• •• ••103 10 nF •• •• •• •• •• •• •• •• •• •• •• •• ••123 12 nF •• •• •• •• •• •• •• •• •• •• •153 15 nF •• •• •• •• •• •• •• •• •• •• •183 18 nF •• •• •• •• •• •• •• •• •• •• •223 22 nF •• •• •• •• •• •• •• •• •• •273 27 nF •• •• •• •• •• •• •• •• •• •333 33 nF •• •• •• •• •• •• •• •• •393 39 nF •• •• •• •• •• •• •• •• •473 47 nF •• •• •• •• •• •• •• •563 56 nF •• •• •• •• •• •• •683 68 nF •• •• •• • • • •823 82 nF •• •• •• • • • •104 100 nF •• •• •• • • • •124 120 nF •• • • •154 150 nF •• • • •184 180 nF • •224 220 nF • •274 270 nF • •334 330 nF • •394 390 nF •474 470 nF •564 560 nF 684 680 nF 824 820 nF 105 1.0 μF 125 1.2 μF 155 1.5 μF 185 1.8 μF 225 2.2 μF 275 2.7 μF 335 3.3 μF 395 3.9 μF 475 4.7 μF 565 5.6 μF 685 6.8 μF
Revision: 06-Nov-14 31 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
Notes• Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1206 VJ1210 (1) VJ1812 (1)
CASE CODE 1206 1210 1812VOLTAGE (VDC) 16 25 50 100 200 500 630 1000 16 25 50 100 200 500 630 50 100 200 500 630VOLTAGE CODE J X A B C E L G J X A B C E L A B C E LCAP. CODE CAP.
121 120 pF 151 150 pF 181 180 pF 221 220 pF • •271 270 pF • •331 330 pF • •391 390 pF • • • •471 470 pF • • • •561 560 pF • • • •681 680 pF • • • •821 820 pF • • • • • • •102 1.0 nF • • • • • • • • • •122 1.2 nF • • • • • • • • •152 1.5 nF • • • • • • • • •182 1.8 nF • • • • • • • • •222 2.2 nF • • • • • • • • • •272 2.7 nF • • • • • • • • • •332 3.3 nF • • • • • • • • • •392 3.9 nF • • • • • • • • • •472 4.7 nF • • • • • • • • • •562 5.6 nF • • • • • • • • • •682 6.8 nF • • • • • • • • • •822 8.2 nF • • • • • • • • • •103 10 nF • • • • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • • • • • • •393 39 nF • • • • • • • • • • • • • • • • •473 47 nF • • • • • • • • • • • • • • •563 56 nF • • • • • • • • • • • • • • •683 68 nF • • • • • • • • • • • • • • •823 82 nF • • • • • • • • • • • • • • •104 100 nF • • • • • • • • • • • • • •124 120 nF • • • • • • • • • • • • •154 150 nF • • • • • • • • • • • •184 180 nF • • • • • • • • • • • •224 220 nF • • • • • • • • • • •274 270 nF • • • • • • • • • • •334 330 nF • • • • • • • • •394 390 nF • • • • • • • • •474 470 nF • • • • • • • • •564 560 nF • • • • • • •684 680 nF • • • • • • •824 820 nF • • • • • • •105 1.0 μF • • • • • •125 1.2 μF 155 1.5 μF 185 1.8 μF 225 2.2 μF 275 2.7 μF 335 3.3 μF 395 3.9 μF 475 4.7 μF 565 5.6 μF 685 6.8 μF
Revision: 06-Nov-14 32 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
Notes•• Paper tape, • Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC X8RSTYLE VJ0402 VJ0603 VJ0805 VJ1206 VJ1210 (1)
CASE CODE 0402 0603 0805 1206 1210VOLTAGE (VDC) 25 50 100 25 50 100 25 50 100 25 50 25 50VOLTAGE CODE X A B X A B X A B X A X ACAP. CODE CAP.
101 100 pF121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF331 330 pF •• •• ••391 390 pF •• •• ••471 470 pF •• •• •• •• •• •• •• ••561 560 pF •• •• •• •• •• •• •• ••681 680 pF •• •• •• •• •• •• •• •• ••821 820 pF •• •• •• •• •• •• •• •• ••102 1.0 nF •• •• •• •• •• •• •• •• •• • •122 1.2 nF •• •• •• •• •• •• •• •• •• • •152 1.5 nF •• •• •• •• •• •• •• •• • •182 1.8 nF •• •• •• •• •• •• •• •• • •222 2.2 nF •• •• •• •• •• •• •• •• • •272 2.7 nF •• •• •• •• •• •• •• • •332 3.3 nF •• •• •• •• •• •• •• • •392 3.9 nF •• •• •• •• •• •• •• • •472 4.7 nF •• •• •• •• •• •• •• • •562 5.6 nF •• •• •• •• •• •• • •682 6.8 nF •• •• •• •• •• •• • •822 8.2 nF •• •• •• •• •• • •103 10 nF •• •• •• •• •• • • • •123 12 nF •• •• •• •• •• • • • •153 15 nF •• •• •• •• •• • • • •183 18 nF •• •• •• •• •• • • • •223 22 nF •• •• •• • • • • •273 27 nF •• •• • • • • • •333 33 nF •• •• • • • • •393 39 nF •• • • • • •473 47 nF • • • • • •563 56 nF • • • • • •683 68 nF • • • • •823 82 nF • • • • •104 100 nF • • • • •124 120 nF • • • •154 150 nF • • •184 180 nF • •224 220 nF • •274 270 nF334 330 nF394 390 nF474 470 nF564 560 nF684 680 nF824 820 nF105 1.0 μF125 1.2 μF
Revision: 06-Nov-14 33 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
Notes(1) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(2) n/a = not available(3) Quantity can vary with customer request(4) Packaging “C / P” or “T / R” and quantity can depend from product thickness
STANDARD PACKAGING QUANTITIES (1)(2)
CASE CODE TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PAPER TAPE PACKAGING CODE
“C”
PLASTIC TAPE PACKAGING CODE
“T”
PAPER TAPE PACKAGING CODE
“P”
PLASTIC TAPE PACKAGING CODE
“R”
0402 8 mm 5000 / 10 000 (3) n/a 10 000 / 30 000 (3) n/a
0603 8 mm 4000 4000 10 000 10 000
0805 (4) 8 mm 3000 3000 10 000 10 000
1206 (4) 8 mm 3000 2500 / 3000 10 000 10 000
1210 (4) 8 mm n/a 2000 / 2500 / 3000 n/a 9000 / 10 000
1812 12 mm n/a 1000 n/a 4000
Revision: 06-Nov-14 34 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
1 - GENERAL CERTIFICATES
2 - TECHNICAL REQUIREMENTSUnless specified in component specification, these parameters are the minimum requirements for the components.
2.1 OPERATING TEMPERATURE RANGE
2.2 CHARACTERISTICS
2.3 STORAGE AND HANDLING CONDITIONS
# Quality management system according to ISO/TS 16949: 2009 Yes
# Quality management system according to ISO 9001: 2008 Yes
# Environmental certification according to ISO 14001: 2004 Yes
# Health and safety system according to OHSA 18001 Yes
For standard applications TA: -55 °C to +125 °C See characteristics 2.2
For high temperature applications TA: -55 °C to +150 °C See characteristics 2.2
For ultra high temperature applications TA: -55 °C to +175 °C See characteristics 2.2
PARAMETER CERAMIC TYPE SYMBOL RATINGS TEST CONDITIONS /
REMARKS
Rated voltage in temperature range -55 °C to +125 °CC0G (NP0)
UR
25 V to 3000 V
X7R 16 V to 1000 V
Rated voltage in temperature range -55 °C to +150 °C X8R 25 V / 50 V
Derating at higher temperature up to +150 °CC0G (NP0) 25 V to 100 V UDC 1/2 UR
X7R 16 V to 100 V UDC 1/2 UR
Derating at higher temperature up to +175 °C
C0G (NP0) 25 V to 100 V UDC 1/4 UR
X7R 16 V to 100 V UDC 1/4 UR
X8R 25 V / 50 V UDC 1/4 UR
Temperature coefficient in temperature range -55 °C to +125 °C
C0G (NP0) C ± 30 ppm/°C if CR < 10 pF: C ± 120 ppm/°C
X7R C ± 15 %
Temperature coefficient in temperature range -55 °C to +150 °C
C0G (NP0) C ± 30 ppm/°C if CR < 10 pF: C ± 120 ppm/°C
X7RC
+ 15 % / - 30 %
X8R ± 15 %
Temperature coefficient in temperature range -55 °C to +175 °C X7R C 15 % / - 50 %
Dissipation factor in temperature range -55 °C to +175 °C
C0G (NP0)
tan
0.0015
X7R 0.06
X8R 0.06
(1) Store the components at 5 °C to 40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 06-Nov-14 35 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
C0G (NP0) DIELECTRIC - TYPICAL PARAMETERS
0.6
0.2
0.0
-0.2
-0.4
-0.6
0.4
-50 0 100 15050
TEMPERATURE DEPENDENCE OF CAPACITANCE
TEMPERATURE IN °C
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE °C
10 25 100 150
10 000
1000
100
10
(ΩF
)
50
INS
ULA
TIO
N R
ES
ISTA
NC
E
INSULATION RESISTANCE VS. TEMPERATURE
AGING RATE
% C
AP
AC
ITA
NC
E C
HA
NG
E
HOURS100 1000 10 000
0.2
0.1
0.0
-0.1
-0.21 10
% C
APA
CIT
AN
CE
CH
AN
GE
VOLTAGE COEFFICIENT OF CAPACITANCE
DC VOLTS APPLIED
0.2
0.1
-0.1
-0.2
0.0
0 10 20 30 40 50 60 70 80 90 100
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
+2
+1
0
-1
-2
% C
AP
AC
ITA
NC
E C
HA
NG
E
CHANGE OF CAPACITANCE WITH FREQUENCY CHANGE OF DISSIPATION FACTOR WITH FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
0.00025
DIS
SIP
AT
ION
FA
CT
OR
0.0005
0.001
Revision: 06-Nov-14 36 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
X7R DIELECTRIC - TYPICAL PARAMETERS
15
10
5
0
-5
-10
-15
-20
TEMPERATURE °C
% C
AP
AC
ITA
NC
E C
HA
NG
E
X7R
-25
-30
-75 -50 -25 0 25 50 75 100 125 150 175
TEMPERATURE COEFFICIENT OF CAPACITANCE
10 000
1000
100
10
MINIMUM INSULATION RESISTANCE VS. TEMPERATURE
20 40 60 80 100 120 140 160 180
TEMPERATURE IN °C
INS
ULA
TIO
N R
ES
ISTA
NC
E IN
ΩF
150 175-75 -50 -25 500 25 75 100 1250.0
TEMPERATURE °C
% D
ISS
IPA
TIO
N F
AC
TO
R
X7R
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.55.0
5.5
6.0DISSIPATION FACTOR VS. TEMPERATURE
HOURS
1.0
0.0
-1.0
-2.0
% C
AP
AC
ITA
NC
E C
HA
NG
E
-3.0
-4.0
AGING RATE
1 10 100 1000 10 000
-75 -50 -25 75 100 125
100
50
VOLTAGE VS. TEMPERATURE
TEMPERATURE °C
% V
OLT
AG
E
150 1750
150
200
0 25 50 180
X7R
VOLTAGE COEFFICIENT OF CAPACITANCE
0
-15
-20
-25
-30
% C
AP
AC
ITA
NE
CH
AN
GE
-10
-5
5
25 V
50 VRATED
100 VRATED
RATED
0 10 20 30 40 50 60 70 80 90 100
DC VOLTS APPLIED
Revision: 06-Nov-14 37 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
X7R DIELECTRIC - TYPICAL PARAMETERS
0.020
0.016
0.012
0.008
0.004
DISSIPATION FACTOR VS. VOLTAGE
DIS
SIP
AT
ION
FA
CT
OR
0 10 20 30 40 50 60 70 80 90 100 UN/V-DC VOLTS APPLIED
50 V
100 V
DISSIPATION FACTOR VS. VOLTAGE
0 100 200 300 400 500 600
0.020
0.016
0.012
0.008
0.000500/630 V
200 V
DC VOLTS APPLIED
DIS
SIP
AT
ION
FA
CT
OR
CHANGE OF CAPACITANCE WITH FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
% C
AP
AC
ITA
NC
E C
HA
NG
E
-10
0
-20
CHANGE OF DISSIPATION FACTOR WITH FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
% D
ISS
IPA
TIO
N F
AC
TO
R
20
10
5
15
0
Revision: 06-Nov-14 38 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
X8R DIELECTRIC - TYPICAL PARAMETERS
-75 -50 -25 0 25 50 75 100 125
15
10
5
0
-5
-10
-15
-20
TEMPERATURE °C
150 175
TEMPERATURE COEFFICIENT OF CAPACITANCE
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE °C
MINIMUM INSULATION RESISTANCE VS. TEMPERATURE
0510015201
10 000
1000
100
10INS
UL
AT
ION
RE
SIS
TAN
CE
(Ω
F)
-75 -50 -25 0 25 50 75 100 1250.0
DISSIPATION FACTOR VS. TEMPERATURE
TEMPERATURE °C
% D
ISS
IPA
TIO
N F
AC
TO
R
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
X8R
150 175
AGING RATE
HOURS
1.0
0.0
-1.0
-2.0
% C
AP
AC
ITA
NC
E C
HA
NG
E
-3.0
-4.0
1 10 100 1000 10 000
Revision: 06-Nov-14 39 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
3 - LOT ACCEPTANCE TESTSProcess tests available in classes (on request)
Upon request the records can be submitted in electronic format on monthly basis.
3.1 THERMAL STRENGTH, THERMAL SHOCK SENSIBILITY
Acceptance criteria: zero defects (IRATS and BIATS).
3.2 BOARD FLEX TEST
3.3 SOLDERABILITY / RESISTANCE TO SOLDERING HEATTemperature profile for reflow soldering of SMD parts IPC/JEDEC-J-STD-020C.
Test is done on a regular basis for samples taken randomly out of the line.
Acceptance criteria: at least 95 % new solder and no detachment or leaching of terminations.
4 - ENVIRONMENTAL REQUIREMENTSA list of the chemical substances content, which must not be used or whose use shall be limited by international law, is availableon request. Vishay confirms that the components specified in this specification do not contain asbestos nor cadmium, not even in thesmallest volumes.The manufacturer / supplier confirms that the component during normal handling, storage and assembly, as well as duringoperation in the automobile, is non toxic.
GROUP ACTION
A Components are tested within the monitoring program of the supplier. The supplier shall submit the part numbers of the selected component to the customer during the component specification discussions.
B Components (customer P/N) shall be tested quarterly. Records available only on special request by the customer.
C Test with each shipment. Records are provided on a monthly basis. Customer special requirement; requirement should be determined in a specific component specification.
Sample size 200
Handling Mounted on PCB
Thermal shock 1 x 280 °C, no pre-heat, 5 s to 10 s
IR - test (IRATS) U = UR, T = room temperature, verified
Burn in (BIATS)Equivalent to 12 h burn-in, 2 x UR/125 °C, verification time to failure
Sample size 20 pcs/lot
X7R, X8R Every lot
C0G At least three different part numbers of one component family matrix per quarter
Max. deflection 8 mm (data to be reported, available on request)
Revision: 06-Nov-14 40 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
5 - INSPECTION CRITERIAThe supplier shall carry out visual examination with suitable equipment with approximately 10 x magnification and lightingappropriate to the specimen under test and the required quality level.
Chipping
The components shall be free of cracks or fissures. Small damages which do not deteriorate the performance of the componentshall be less than 50 % of the surface of the MLCC as defined in EIA 595.
Delamination or Exposed Electrodes
No visible separation or delamination between layers of the capacitor and no exposed electrodes between the two terminals ofthe capacitor must be seen.
Metallization
For the metallization, no visible detachment of the metallized terminals and no exposed electrodes must be seen. Defects andgaps in the metallization on each sides of the terminal must not exceed 10 % of the total area (e.g. A, B, C, …). Leaching shallnot exceed 25 %.
Electrode Distance
The ceramic body shall be free of any conducting material between the terminals which reduces the distance of the electrodes.The minimum distance “D” is 400 μm for all package sizes, except 0402. For the component package 0402 the minimumdistance is 200 μm.
C
A B
D
Revision: 06-Nov-14 41 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
6 - BOARD FLEX TEST CONDITIONS
6.1 BOARD FLEX DEFINITIONS OF TESTPCB thickness = (1.6 ± 0.1) mm
Copper thickness = 35 μm
Material FR4 (EP-GC 02 according to DIN 40 802)
Note• LL = total length; LB = width of the pad; LEL = single pad length
6.2 SOLDERING INSTRUCTIONS
6.3 TYPICAL TEMPERATURE PROFILE FOR REFLOW SOLDERING (Boardflex test)
LAYOUT / PAD DESIGN (Dimensions in mm)
CASE CODEPAD SIZE
LL LB LEL0603 2.20 1.00 0.750805 3.40 1.30 1.201206 4.50 1.80 1.201210 4.50 2.80 1.301812 4.75 3.60 1.50
THICKNESS, RECOMMENDED FOR SOLDER PASTE (Reflow soldering)CASE CODE THICKNESS in μm
0402 75 to 90
0603 150 to 200
0805 150 to 200
1206 150 to 200
1210 150 to 200
1812 150 to 200
LEL
LLLB
TE
MP
ER
AT
UR
E (°
C)
300
250
200
150
100
0 50 100 150 200 250 300 350 400TIME (s)
LEAD (Pb)-FREE SOLDERING PROFILE
MIN. 300 s MAX. 260 °C MIN. 255 °C
T (SOLID) MIN. 217 °C
MIN. 190 °CMIN. 40 sMIN. 90 s
RAMP UP TO 150 °CMAX. 3 K/s
RAMP DOWN FROM T (SOLID)
MAX. 6 K/sMIN. 110 s50
0
Revision: 06-Nov-14 42 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
6.4 MOUNTING, DIMENSIONS, AND TESTING
Mounting
Testing
6.5 PERFORMANCE OF THE TEST(S)A) Electrical test according to component specification (Cap, DF, IR)
B) Mounting to PCB
C) Storage at room temperature (min. 10 h)
D) Board flex test
6.6 DETAILS
6.7 FAILURE CRITERIA
X7R, X8R PCB to be deflected continuously, speed 1 mm/s (± 0.5 mm/s)
C0G PCB to be deflected in steps until cracks or other damages are visible or can be measured.Dwell time between steps: (5 ± 1) s
X7R, X8R Piezoelectric sensor, no failure up to min. 2 mm
C0G C/C < 1 % or < 1 pF, no failure up to min. 2 mm
Both Electrical test according to component specification
SMD under test
Solder
Support
1.6 ± 0.1
90 ± 1
45 ± 2
Printed boardbefore test
R = 3
+ +
+ +
Material: Aluminum20
Printed boardduring test
Width = actual widthof substrate + 5 mm on both sides
Radius1 to 2
Width
1.5 ± 0.1
0
All dimensions in mm
10 ± 0.1
Revision: 06-Nov-14 43 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31X RoHS Automotive MLCCwww.vishay.com Vishay Vitramon
7 - AEC-Q200 QUALIFICATION TESTING
NO. AEC-Q200 TEST ITEM REFERENCE
1 Pre- and post stress electrical test User spec
3 High temp exposure (storage) MIL-STD-202, method 108
4 Temperature cycling JESD22, method JA-104
5 Destructive physical analysis EIA-469
6 Moisture resistance MIL-STD-202, method 106
7 Biased humidity MIL-STD-202, method 103
8 Operation life MIL-STD-202 method 108
9 External Visual MIL-STD-883 method 2009
10 Physical dimension JESD22, method JB-100
13 Mechanical shock MIL-STD-202, method 213
14 Vibration MIL-STD-202, method 204
15 Resistance to solder heat MIL-STD-202, method 215
16 ESD AEC-Q200 rev. C
17 Solderability J-STD-002
20 Electrical characterization User spec
21 Board flex AEC-Q200-005
22 Terminal strength AEC-Q200-006
23 Beam load AEC-Q200-003
Revision: 06-Nov-14 44 Document Number: 45226For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitorsfor Automotive Applications
FEATURES• AEC-Q200 qualified with PPAP available• Available in 0402 to 1812 body size• Four dielectric materials• AgPd termination available for silver epoxy
bonding• High operating temperature• Wet build process• Reliable Noble Metal Electrode (NME) system• Parts compliant with ELV directive• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912 Note* This datasheet provides information about parts that are
RoHS-compliant and/or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information/tables in this datasheet for details.
For more than 25 years Vishay Vitramon has supported the automotive industry with robust, highly reliable MLCCs that havemade it a leader in this segment. All Vishay Vitramon MLCCs are manufactured in “Precious Metal Technology” (PMT / NME)and a wet build process. They are qualified according to AEC-Q200 with PPAP available on request. Applications for thesedevices include automotive “under the hood”, safety and comfort electronics. Their termination finish is 100 % matte tin platefinish and AgPd which is used with silver epoxy bonding. A polymer (flexible) termination with 100 % matte tin plate finish isoffered for boardflex sensitive applications.
Available
C0G (NP0) DIELECTRIC
GENERAL SPECIFICATIONNote Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +150 °C (above +125 °C changed characteristics, see 2.3)
Capacitance Range: 1 pF to 22 nF
Voltage Range: 25 VDC to 3000 VDC
Temperature Coefficient of Capacitance (TCC):0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
Dissipation Factor (DF):0.1 % maximum at 1.0 VRMS and 1 MHz for values 1000 pF0.1 % maximum at 1.0 VRMS and 1 kHz for values > 1000 pF
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging: 0 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 250 VDC-rated: 250 % of rated voltage500 VDC-rated: 200 % of rated voltage630 VDC, 1000 VDC-rated: 150 % of rated voltage3000 VDC-rated: 120 % of rated voltage
X7R, X8R DIELECTRIC
GENERAL SPECIFICATIONNote Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +150 °C (X7R above +125 °C changed characteristics, see 2.3)
Capacitance Range: 120 pF to 1.0 μF
Voltage Range: 16 VDC to 1000 VDC
Temperature Coefficient of Capacitance (TCC):X7R: ± 15 % from -55 °C to +125 °C, with 0 VDC appliedX8R: ± 15 % from -55 °C to +150 °C, with 0 VDC applied
Dissipation Factor (DF):10 V ratings: 5 % maximum at 1.0 VRMS and 1 kHz16 V, 25 V ratings: 3.5 % maximum at 1.0 VRMS and 1 kHz > 25 V ratings: 2.5 % maximum at 1.0 VRMS and 1 kHz
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 1 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 250 VDC-rated: 250 % of rated voltage500 VDC-rated: min. 150 % of rated voltage630 VDC, 1000 VDC-rated: min. 120 % of rated voltage
Revision: 23-Oct-14 45 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
QUICK REFERENCE DATA
DIELECTRIC CASE CODE MAXIMUM VOLTAGE (V)
CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0)
0402 100 1.0 pF 220 pF
0603 200 1.0 pF 1.0 nF
0805 500 1.0 pF 3.9 nF
1206 630 1.0 pF 10 nF
1210 630 100 pF 12 nF
1812 3000 12 pF 22 nF
X7R
0402 100 120 pF 47 nF
0603 200 330 pF 150 nF
0805 500 330 pF 470 nF
1206 630 220 pF 1.0 μF
1210 630 390 pF 1.0 μF
1812 630 10 nF 1.0 μF
X8R
0402 100 330 pF 6.8 nF
0603 100 470 pF 33 nF
0805 100 470 pF 100 nF
1206 50 1.0 nF 220 nF
1210 50 10 nF 390 nF
Revision: 23-Oct-14 46 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
Notes(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected](2) Case size designator may be replaced by a four digit drawing number(3) Polymer termination contact [email protected] for availability of ratings(4) Non-standard values please contact: [email protected] for availability(5) Packaging “T” and “R” is used for 1812 size(6) Termination code “E” is for conductive epoxy assembly.(7) Termination code “B” and “F” are not available with X8R in 0402, 0603 - 100 V, 0805 - 100 V.
ORDERING INFORMATION - TIN TERMINATIONVJ0805 (2) Y 102 K X A A C 31
CASE CODE
DIELECTRIC CAPACITANCE NOMINAL CODE (4)
CAPACITANCE TOLERANCE
TERMINATION DC VOLTAGE RATING (1)
MARKING PACKAGING PROCESS CODE
040206030805120612101812
A = C0G (NP0)
Y = X7RH = X8R
Expressed in picofarads (pF).
The first two digits are
significant, the third is a
multiplier. An “R” indicates a decimal point.
Examples4R7 = 4.7 pF
102 = 1000 pF
B = ± 0.10 pFC = ± 0.25 pF D = ± 0.5 pF
F = ± 1 % G = ± 2 % J = ± 5 %
K = ± 10 %M = ± 20 %
Note:C0G (NP0):
B, C, D < 10 pFF, G, J, K 10 pF
X7R / X8R:J, K, M
X = Ni barrier 100 % matte tin
plate finishB = polymer
100 % matte tin plate finish (3)(7)
J = 16 VX = 25 VA = 50 V
B = 100 VC = 200 VP = 250 VE = 500 VL = 630 V
G = 1000 VH = 3000 V
A = unmarkedB = marked
Note: marking is only
available for 0805 and 1206 vendor ID and
date code
31 = automotive
100 % matte tin
plate finish
E / T = 7" reel / plastic tape (5)
C = 7" reel / paper tapeM / R = 11 1/4" / 13" reel / plastic tape (5)
P = 11 1/4" / 13" reel / paper tape
ORDERING INFORMATION - SILVER PALLADIUM TERMINATIONVJ0805 (2) Y 102 K F A A O 34
CASE CODE
DIELECTRIC CAPACITANCE NOMINAL CODE (4)
CAPACITANCE TOLERANCE
TERMINATION DC VOLTAGE RATING (1)
MARKING PACKAGING PROCESS CODE
040206030805120612101812
A = C0G (NP0)
Y = X7RH = X8R
Expressed in picofarads (pF).
The first two digits are
significant, the third is a
multiplier. An “R” indicates a decimal point.
Examples102 = 1000 pF
B = ± 0.10 pFC = ± 0.25 pF D = ± 0.5 pF
F = ± 1 % G = ± 2 % J = ± 5 %
K = ± 10 %M = ± 20 %
Note:C0G (NP0):
B, C, D < 10 pFF, G, J, K 10 pF
X7R / X8R:J, K, M
F, E = AgPd (6)(7) J = 16 VX = 25 VA = 50 V
B = 100 VC = 200 VP = 250 VE = 500 VL = 630 V
G = 1000 VH = 3000 V
A = unmarkedNote:
marking is not available
34 = automotive AgPd finish
E / T = 7" reel / plastic tape (5)
O = 7" reel / flamed paper tapeM / R = 11 1/4" / 13" reel / plastic tape (5)
I = 11 1/4" / 13" reel / flamed paper tapeNote:
“I” and “O” are used for “F”, “E” termination
size 0402 / 0603 / 0805
Revision: 23-Oct-14 47 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
Note• Polymer (B-termination) have increased dimensions:
part length increased by 0.006" (0.15 mm)
DIMENSIONS in inches (millimeters)
CASE CODE STYLE LENGTH
(L)WIDTH
(W)
MAXIMUM THICKNESS
(T)
TERMINATIONS PAD (P)
MINIMUM MAXIMUM
0402 VJ0402 0.040 + 0.004 / - 0.002(1.00 + 0.10 / - 0.05)
0.020 + 0.004 / - 0.002(0.50 + 0.10 / - 0.05)
0.024(0.60)
0.004(0.10)
0.016(0.41)
0603 VJ0603 0.063 ± 0.006(1.60 ± 0.15)
0.031 ± 0.006(0.80 ± 0.15)
0.038(0.97)
0.012(0.30)
0.018(0.46)
0805 VJ0805 0.079 ± 0.008(2.00 ± 0.20)
0.049 ± 0.008(1.25 ± 0.20)
0.057(1.45)
0.010(0.25)
0.028(0.71)
1206 VJ1206 0.126 ± 0.010(3.20 ± 0.25)
0.063 ± 0.010(1.60 ± 0.25)
0.067(1.70)
0.010(0.25)
0.028(0.71)
1210 VJ1210 0.126 ± 0.010(3.20 ± 0.25)
0.098 ± 0.010(2.50 ± 0.25)
0.076(1.94)
0.010(0.25)
0.028(0.71)
1812 VJ1812 0.177 ± 0.010(4.50 ± 0.25)
0.126 ± 0.010(3.20 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
L W
P
TMAX.
Revision: 23-Oct-14 48 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
Notes•• Paper tape, • Plastic tape, ++ Paper tape, + Plastic tape, see table “Product drawings (in use)”(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
RoHS-compliantNot RoHS-compliant
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ0402 VJ0603 VJ0805CASE CODE 0402 0603 0805VOLTAGE (VDC) 25 / 50 100 50 100 200 50 100 200 500VOLTAGE CODE X / A B A B C A B C ECAP. CODE CAP.
1R0 1.0 pF •• •• •• •• •• •• •• •• ••1R2 1.2 pF •• •• •• •• •• •• •• •• ••1R5 1.5 pF •• •• •• •• •• •• •• •• ••1R8 1.8 pF •• •• •• •• •• •• •• •• ••2R2 2.2 pF •• •• •• •• •• •• •• •• ••2R7 2.7 pF •• •• •• •• •• •• •• •• ••3R3 3.3 pF •• •• •• •• •• •• •• •• ••3R9 3.9 pF •• •• •• •• •• •• •• •• ••4R7 4.7 pF •• •• •• •• •• •• •• •• ••5R6 5.6 pF •• •• •• •• •• •• •• •• ••6R8 6.8 pF •• •• •• •• •• •• •• •• ••8R2 8.2 pF •• •• •• •• •• •• •• •• ••100 10 pF •• •• •• •• •• •• •• •• ••120 12 pF •• •• •• •• •• •• •• •• ••150 15 pF •• •• •• •• •• •• •• •• ••180 18 pF •• •• •• •• •• •• •• •• ••220 22 pF ++ ++ •• •• •• •• •• •• ••270 27 pF ++ ++ •• •• •• •• •• •• ••330 33 pF ++ ++ •• •• •• •• •• •• ••390 39 pF ++ ++ •• •• •• •• •• •• ••470 47 pF ++ ++ •• •• •• •• •• •• ••560 56 pF ++ ++ ++ ++ ++ •• •• •• ••680 68 pF ++ ++ ++ ++ ++ •• •• •• ••820 82 pF ++ ++ ++ ++ ++ •• •• •• ••101 100 pF ++ ++ ++ ++ ++ ++ ++ ++ ++121 120 pF ++ ++ ++ ++ ++ ++ ++ ++ ++151 150 pF ++ ++ ++ ++ ++ ++ ++ ++181 180 pF ++ ++ ++ + ++ ++ ++ ++221 220 pF ++ ++ ++ + ++ ++ ++ +271 270 pF ++ ++ + ++ ++ ++ +331 330 pF ++ ++ ++ ++ ++ +391 390 pF ++ ++ ++ ++ ++ +471 470 pF ++ ++ ++ ++ + +561 560 pF ++ ++ ++ +681 680 pF ++ ++ ++ +821 820 pF ++ ++ ++ +102 1.0 nF ++ ++ ++ +122 1.2 nF ++ +152 1.5 nF ++ +182 1.8 nF + +222 2.2 nF +272 2.7 nF +332 3.3 nF +392 3.9 nF +472 4.7 nF562 5.6 nF682 6.8 nF822 8.2 nF103 10 nF123 12 nF153 15 nF183 18 nF223 22 nF273 27 nF333 33 nF393 39 nF473 47 nF 563 56 nF
Revision: 23-Oct-14 49 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
Notes•• Paper tape, • Plastic tape, ++ Paper tape, + Plastic tape, see table “Product drawings (in use)”(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
RoHS-compliantNot RoHS-compliant
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1206 (1) VJ1210 (1) VJ1812 (1)
CASE CODE 1206 1210 1812VOLTAGE (VDC) 50 100 200 250 500 / 630 50 100 200 500 / 630 50 100 200 500 / 630 1000 3000VOLTAGE CODE A B C P E / L A B C E / L A B C E / L G HCAP. CODE CAP.
1R0 1.0 pF •• •• •• ••1R2 1.2 pF •• •• •• ••1R5 1.5 pF •• •• •• ••1R8 1.8 pF •• •• •• ••2R2 2.2 pF •• •• •• ••2R7 2.7 pF •• •• •• ••3R3 3.3 pF •• •• •• ••3R9 3.9 pF •• •• •• ••4R7 4.7 pF •• •• •• ••5R6 5.6 pF •• •• •• ••6R8 6.8 pF •• •• •• ••8R2 8.2 pF •• •• •• ••100 10 pF •• •• •• ••120 12 pF •• •• •• •• •150 15 pF •• •• •• •• •180 18 pF •• •• •• •• •220 22 pF •• •• •• •• • •270 27 pF •• •• •• •• • •330 33 pF •• •• •• •• • •390 39 pF •• •• •• •• • • • • • •470 47 pF •• •• •• •• • • • • • •560 56 pF •• •• •• •• • • • • • •680 68 pF •• •• •• •• • • • • • •820 82 pF •• •• •• •• • • • • • •101 100 pF + + + + + + + + • • • • • •121 120 pF + + + + + + + + • • • • •151 150 pF + + + + + + + + • • • • •181 180 pF + + + + + + + + • • • • •221 220 pF + + + + + + + + • • • • •271 270 pF + + + + + + + + • • • • •331 330 pF + + + + + + + + • • • • •391 390 pF + + + + + + + + • • • • •471 470 pF + + + + + + + + • • • • •561 560 pF + + + + + + + + • • • • •681 680 pF + + + + + + + + • • • • •821 820 pF + + + + + + + + • • • • •102 1.0 nF + + + + + + + + • • • • •122 1.2 nF + + + + + + + • • • • •152 1.5 nF + + + + + + + • • • • •182 1.8 nF + + + + + + + • • • • •222 2.2 nF + + + + + + + • • • • •272 2.7 nF + + + + + + • • • •332 3.3 nF + + + + + + • • • •392 3.9 nF + + + + + • • • •472 4.7 nF + + + + + • • • •562 5.6 nF + + + + + • • •682 6.8 nF + + + + + • • •822 8.2 nF + + + + + • • •103 10 nF + + + + • • •123 12 nF + + • • •153 15 nF • •183 18 nF •223 22 nF •273 27 nF333 33 nF393 39 nF473 47 nF 563 56 nF
Revision: 23-Oct-14 50 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
Notes•• Paper tape, • Plastic tape, ++ Paper tape, + Plastic tape, see table “Product drawings (in use)”(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
RoHS-compliantNot RoHS-compliant
SELECTION CHARTDIELECTRIC X7RSTYLE VJ0402 VJ0603 VJ0805CASE CODE 0402 0603 0805VOLTAGE (VDC) 16 25 50 100 16 25 50 100 200 16 25 50 100 200 250 500VOLTAGE CODE J X A B J X A B C J X A B C P ECAP. CODE CAP.
121 120 pF •• •• •• ••151 150 pF •• •• •• ••181 180 pF •• •• •• ••221 220 pF •• •• •• ••271 270 pF •• •• •• ••331 330 pF •• •• •• •• •• •• •• •• •• •• •• ••391 390 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••471 470 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••561 560 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••681 680 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••821 820 pF •• •• •• •• •• •• •• •• •• •• •• •• •• ••102 1.0 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••122 1.2 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••152 1.5 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••182 1.8 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••222 2.2 nF •• •• •• •• •• •• •• •• •• •• •• •• •• ••272 2.7 nF •• •• •• ++ •• •• •• •• •• •• •• •• •• ••332 3.3 nF •• •• •• ++ •• •• •• •• •• •• •• •• •• •• •392 3.9 nF •• •• •• ++ •• •• •• •• •• •• •• •• •• ••472 4.7 nF •• •• •• ++ •• •• •• •• •• •• •• •• •• ••562 5.6 nF •• •• ++ •• •• •• •• •• •• •• •• ••682 6.8 nF •• •• ++ •• •• •• •• •• •• •• •• ••822 8.2 nF •• •• ++ •• •• •• •• •• •• •• •• ••103 10 nF ++ ++ ++ •• •• •• •• •• •• •• •• •• ••123 12 nF ++ ++ •• •• •• ++ •• •• •• •• •153 15 nF ++ ++ •• •• •• ++ •• •• •• •• •183 18 nF ++ ++ •• •• •• ++ •• •• •• •• •223 22 nF ++ •• •• •• ++ •• •• •• •• •273 27 nF ++ •• •• •• ++ •• •• •• •• •333 33 nF ++ •• •• ++ ++ •• •• •• •393 39 nF ++ •• •• ++ ++ •• •• •• •473 47 nF ++ •• •• ++ •• •• •• •563 56 nF •• ++ ++ •• •• •• +683 68 nF •• ++ ++ + + + + 823 82 nF •• ++ ++ + + + + 104 100 nF ++ ++ ++ + + + + 124 120 nF + + + + 154 150 nF + + + + 184 180 nF + + 224 220 nF + + 274 270 nF + + 334 330 nF + + 394 390 nF + 474 470 nF + 564 560 nF 684 680 nF 824 820 nF 105 1.0 μF 125 1.2 μF 155 1.5 μF 185 1.8 μF 225 2.2 μF 275 2.7 μF 335 3.3 μF 395 3.9 μF 475 4.7 μF 565 5.6 μF 685 6.8 μF
Revision: 23-Oct-14 51 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
Notes•• Paper tape, • Plastic tape, ++ Paper tape, + Plastic tape, see table “Product drawings (in use)”(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
RoHS-compliantNot RoHS-compliant
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1206 (1) VJ1210 (1) VJ1812 (1)
CASE CODE 1206 1210 1812VOLTAGE (VDC) 16 25 50 100 200 500 / 630 16 25 50 100 200 500 / 630 50 100 200 500 630VOLTAGE CODE J X A B C E / L J X A B C E / L A B C E LCAP. CODE CAP.
121 120 pF 151 150 pF 181 180 pF 221 220 pF •271 270 pF •331 330 pF •391 390 pF • •471 470 pF • •561 560 pF • •681 680 pF • •821 820 pF • • • • •102 1.0 nF • • • • • • •122 1.2 nF • • • • • • •152 1.5 nF • • • • • • •182 1.8 nF • • • • • • •222 2.2 nF • • • • • • • •272 2.7 nF • • • • • • • •332 3.3 nF • • • • • • • •392 3.9 nF • • • • • • • •472 4.7 nF • • • • • • • •562 5.6 nF • • • • • • • •682 6.8 nF • • • • • • • •822 8.2 nF • • • • • • • •103 10 nF • • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • • • •183 18 nF • • • • • + • • • • • • • • •223 22 nF • • • • • • • • • • + • • • • •273 27 nF • • • • • • • • • • + • • • • •333 33 nF • • • • • • • • • • + • • • • •393 39 nF • • • • • • • • • • + • • • • •473 47 nF • • • • • • • • • • • • • • •563 56 nF • • • • • • • • • • • • • • •683 68 nF • • • • • • • • • • • • • • •823 82 nF • • • • + • • • • • • • • • •104 100 nF • • • + + • • • + + • • • •124 120 nF • • • + + • • • + + • • •154 150 nF • • + + • • • + + • • •184 180 nF • • + + • • • + + • • •224 220 nF + + + + + + + + • • •274 270 nF + + + + + + + + • • •334 330 nF + + + + + + + • •394 390 nF + + + + + + + • •474 470 nF + + + + + + + • •564 560 nF + + + + + • •684 680 nF + + + + + • •824 820 nF + + + + + • •105 1.0 μF + + + + + •125 1.2 μF 155 1.5 μF 185 1.8 μF 225 2.2 μF 275 2.7 μF 335 3.3 μF 395 3.9 μF 475 4.7 μF 565 5.6 μF 685 6.8 μF
Revision: 23-Oct-14 52 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
Notes•• Paper tape, • Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034(2) For other voltage ratings, please contact [email protected]
RoHS-compliantNot RoHS-compliant
SELECTION CHARTDIELECTRIC X8RSTYLE VJ0402 VJ0603 VJ0805 VJ1206 (1) VJ1210 (1)
CASE CODE 0402 0603 0805 1206 1210VOLTAGE (VDC) (2) 25 50 100 25 50 100 25 50 100 25 50 25 50VOLTAGE CODE X A B X A B X A B X A X ACAP. CODE CAP.
101 100 pF121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF331 330 pF •• •• ••391 390 pF •• •• ••471 470 pF •• •• •• •• •• •• •• ••561 560 pF •• •• •• •• •• •• •• ••681 680 pF •• •• •• •• •• •• •• •• ••821 820 pF •• •• •• •• •• •• •• •• ••102 1.0 nF •• •• •• •• •• •• •• •• •• • •122 1.2 nF •• •• •• •• •• •• •• •• •• • •152 1.5 nF •• •• •• •• •• •• •• •• • •182 1.8 nF •• •• •• •• •• •• •• •• • •222 2.2 nF •• •• •• •• •• •• •• •• • •272 2.7 nF •• •• •• •• •• •• •• • •332 3.3 nF •• •• •• •• •• •• •• • •392 3.9 nF •• •• •• •• •• •• •• • •472 4.7 nF •• •• •• •• •• •• •• • •562 5.6 nF •• •• •• •• •• •• • •682 6.8 nF •• •• •• •• •• •• • •822 8.2 nF •• •• •• •• •• • •103 10 nF •• •• •• •• •• • • • •123 12 nF •• •• •• •• •• • • • •153 15 nF •• •• •• •• •• • • • •183 18 nF •• •• •• •• •• • • • •223 22 nF •• •• •• • • • • •273 27 nF •• •• • • • • • •333 33 nF •• •• • • • • •393 39 nF •• • • • • •473 47 nF • • • • • •563 56 nF • • • • • •683 68 nF • • • • •823 82 nF • • • • •104 100 nF • • • • •124 120 nF • • • •154 150 nF • • •184 180 nF • • •224 220 nF • • •274 270 nF • •334 330 nF • •394 390 nF •474 470 nF564 560 nF684 680 nF824 820 nF105 1.0 μF125 1.2 μF
Revision: 23-Oct-14 53 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
Notes(1) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(2) n/a = not available(3) Quantity can vary with customer request(4) Flamed paper tape code “O” (7" reel) and “I” (11 1/4/13" reel) for AgPd terminated parts (termination code F, E)(5) Packaging “C/P” or “E/M” and quantity can depend from product thickness(6) Packaging code “T”, “R” are used for size 1812.
PRODUCT DRAWING (in use)
CASE CODE CODE
X - TERMINATION CODE(100 % MATTE TIN)
F - TERMINATION CODE(AgPd)
DRAWING C0G (NP0) DRAWING X7R DRAWING C0G (NP0) DRAWING X7R
0402•• = paper tape 7175 9172 7175 9072
++ = paper tape 7172 7172 7072 7072
0603
•• = paper tape 7179 9155 7179 9097
++ = paper tape 7155 7155 7097 7097
• = plastic tape - - 7179 9097
+ = plastic tape 7155 7155 7097 7097
0805
•• = paper tape 7188 9156 7188 9080
++ = paper tape 7156 7156 7080 7080
• = plastic tape - 9156 7188 9080
+ = plastic tape 7156 7156 7080 7080
1206
•• = paper tape 7180 - - -
• = plastic tape - 9157 7180 9081
+ = plastic tape 7157 7157 7081 7081
1210• = plastic tape - 9158 - 9099
+ = plastic tape 7158 7158 7099 7099
STANDARD PACKAGING QUANTITIES (1)(2)
CASE CODE TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PAPER TAPE PACKAGING CODE
“C” / “O” (4)
PLASTIC TAPE PACKAGING CODE
“E / T” (6)
PAPER TAPE PACKAGING CODE
“P” / “I” (4)
PLASTIC TAPE PACKAGING CODE
“M / R” (6)
0402 8 mm 5000 / 10 000 (3) n/a 10 000 / 30 000 (3) n/a
0603 8 mm 4000 4000 10 000 10 000
0805 (5) 8 mm 3000 3000 10 000 10 000
1206 (5) 8 mm 3000 2500 / 3000 10 000 9000 / 10 000
1210 (5) 8 mm n/a 2000 / 2500 / 3000 n/a 9000 / 10 000
1812 12 mm n/a 1000 n/a 4000
Revision: 23-Oct-14 54 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
1 - GENERAL CERTIFICATES
2 - TECHNICAL REQUIREMENTSUnless specified in component specification, these parameters are the minimum requirements for the components.
2.1 OPERATING TEMPERATURE RANGE
2.2 STORAGE AND HANDLING CONDITIONS
2.3 CHARACTERISTICS
# Quality management system according to ISO/TS 16949: 2009 Yes
# Quality management system according to ISO 9001: 2008 Yes
# Environmental certification according to ISO 14001: 2004 Yes
# Health and safety system according to OHSA 18001 Yes
For standard applications TA: -55 °C to +125 °C See characteristics 2.3
For high temperature applications TA: -55 °C to +150 °C See characteristics 2.3
For ultra high temperature applications TA: -55 °C to +175 °C See characteristics 2.3
(1) Store the components at 5 °C to 40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
PARAMETER CERAMIC TYPE SYMBOL RATINGS TEST CONDITIONS/
REMARKS
Rated voltage in temperature range -55 °C to +125 °CC0G (NP0)
UR
25 V to 3000 V
X7R 16 V to 630 V
Rated voltage in temperature range -55 °C to +150 °C X8R 25 V/50 V
Derating at higher temperature up to +150 °CC0G (NP0), 25 V to 100 V UDC 1/2 UR
X7R 16 V to 100 V UDC 1/2 UR
Derating at higher temperature up to +175 °C
C0G (NP0), 25 V to 100 V UDC 1/4 UR
X7R 16 V to 100 V UDC 1/4 UR
X8R 25 V/50 V UDC 1/4 UR
Temperature coefficient in temperature range -55 °C to +125 °C
C0G (NP0) C ± 30 ppm/C if CR < 10 pF: C ± 120 ppm/K
X7R C ± 15 %
Temperature coefficient in temperature range -55 °C to +150 °C
C0G (NP0) C ± 30 ppm/C if CR < 10 pF: C ± 120 ppm/K
X7RC
+15 %/-30 %
X8R ± 15 %
Temperature coefficient in temperature range -55 °C to +175 °C X7R C 15 %/-50 %
Dissipation factor in temperature range -55 °C to +175 °C
C0G (NP0)
tan
0.0015
X7R 0.06
X8R 0.06
Revision: 23-Oct-14 55 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
C0G (NP0) DIELECTRIC - TYPICAL PARAMETERS
0.6
0.2
0.0
-0.2
-0.4
-0.6
0.4
-50 0 100 15050
TEMPERATURE DEPENDENCE OF CAPACITANCE
TEMPERATURE IN °C
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE °C
10 25 100 150
10 000
1000
100
10
(ΩF
)
50
INS
ULA
TIO
N R
ES
ISTA
NC
E
INSULATION RESISTANCE VS. TEMPERATURE
AGING RATE
% C
AP
AC
ITA
NC
E C
HA
NG
E
HOURS100 1000 10 000
0.2
0.1
0.0
-0.1
-0.21 10
% C
APA
CIT
AN
CE
CH
AN
GE
VOLTAGE COEFFICIENT OF CAPACITANCE
DC VOLTS APPLIED
0.2
0.1
-0.1
-0.2
0.0
0 10 20 30 40 50 60 70 80 90 100
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
+1
0
-1
-2
% C
AP
AC
ITA
NC
E C
HA
NG
E
+2CHANGE OF CAPACITANCE WITH FREQUENCY CHANGE OF DISSIPATION FACTOR WITH FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
0.00025
DIS
SIP
AT
ION
FA
CT
OR
0.0005
0.001
Revision: 23-Oct-14 56 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
X7R DIELECTRIC - TYPICAL PARAMETERS
15
10
5
0
-5
-10
-15
-20
TEMPERATURE °C
% C
AP
AC
ITA
NC
E C
HA
NG
E
X7R
-25
-30
-75 -50 -25 0 25 50 75 100 125 150 175
TEMPERATURE COEFFICIENT OF CAPACITANCE
10 000
1000
100
10
MINIMUM INSULATION RESISTANCE VS. TEMPERATURE
20 40 60 80 100 120 140 160 180
TEMPERATURE IN °C
INS
ULA
TIO
N R
ES
ISTA
NC
E IN
ΩF
150 175-75 -50 -25 0 25 50 75 100 1250.0
TEMPERATURE °C
% D
ISS
IPA
TIO
N F
AC
TO
R
X7R
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.55.0
5.5
6.0DISSIPATION FACTOR VS. TEMPERATURE
HOURS
1.0
0.0
-1.0
-2.0
% C
AP
AC
ITA
NC
E C
HA
NG
E
-3.0
-4.0
AGING RATE
1 10 100 1000 10 000
-75 -50 -25 75 100 125
100
50
VOLTAGE VS. TEMPERATURE
TEMPERATURE °C
% V
OLT
AG
E
150 1750
150
200
0 25 50 180
X7R
VOLTAGE COEFFICIENT OF CAPACITANCE
0
-15
-20
-25
-30
% C
AP
AC
ITA
NE
CH
AN
GE
-10
-5
5
25 V
50 VRATED
100 VRATED
RATED
0 10 20 30 40 50 60 70 80 90 100
DC VOLTS APPLIED
Revision: 23-Oct-14 57 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
X7R DIELECTRIC - TYPICAL PARAMETERS
0.020
0.016
0.012
0.008
0.004
DISSIPATION FACTOR VS. VOLTAGE
DIS
SIP
AT
ION
FA
CT
OR
0 10 20 30 40 50 60 70 80 90 100 UN/V-DC VOLTS APPLIED
50 V
100 V
DISSIPATION FACTOR VS. VOLTAGE
0 100 200 300 400 500 600
0.020
0.016
0.012
0.008
0.000500/630 V
200 V
DC VOLTS APPLIED
DIS
SIP
AT
ION
FA
CT
OR
CHANGE OF CAPACITANCE WITH FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
% C
AP
AC
ITA
NC
E C
HA
NG
E
-10
0
-20
CHANGE OF DISSIPATION FACTOR WITH FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
% D
ISS
IPA
TIO
N F
AC
TO
R
20
10
5
15
0
Revision: 23-Oct-14 58 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
X8R DIELECTRIC - TYPICAL PARAMETERS
-75 -50 -25 0 25 50 75 100 125
15
10
5
0
-5
-10
-15
-20
TEMPERATURE °C
150 175
TEMPERATURE COEFFICIENT OF CAPACITANCE
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE °C
MINIMUM INSULATION RESISTANCE VS. TEMPERATURE
0510015201
10 000
1000
100
10INS
UL
AT
ION
RE
SIS
TAN
CE
(Ω
F)
-75 -50 -25 0 25 50 75 100 1250.0
DISSIPATION FACTOR VS. TEMPERATURE
TEMPERATURE °C
% D
ISS
IPA
TIO
N F
AC
TO
R
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
X8R
150 175
AGING RATE
HOURS
1.0
0.0
-1.0
-2.0
% C
AP
AC
ITA
NC
E C
HA
NG
E
-3.0
-4.0
1 10 100 1000 10 000
Revision: 23-Oct-14 59 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
3 - LOT ACCEPTANCE TESTSProcess tests available in classes (on request)
Upon request the records can be submitted in electronic format on monthly basis.
3.1 THERMAL STRENGTH, THERMAL SHOCK SENSIBILITY
Acceptance criteria: zero defects (IRATS and BIATS).
3.2 BOARD FLEX TEST
3.3 SOLDERABILITY/RESISTANCE TO SOLDERING HEATTemperature profile for reflow soldering of SMD parts IPC/JEDEC-J-STD-020C.
Test is done on a regular basis for samples taken randomly out of the line.
Acceptance criteria: at least 95 % new solder and no detachment or leaching of terminations.
4 - ENVIRONMENTAL REQUIREMENTSA list of the chemical substances content, which must not be used or whose use shall be limited by international law, is availableon request. Vishay confirms that the components specified in this specification do not contain asbestos nor cadmium, not even in thesmallest volumes.The manufacturer/supplier confirms that the component during normal handling, storage and assembly, as well as duringoperation in the automobile, is non toxic.
GROUP ACTION
A Components are tested within the monitoring program of the supplier. The supplier shall submit the part numbers of the selected component to the customer during the component specification discussions.
B Components (customer P/N) shall be tested quarterly. Records available only on special request by the customer.
C Test with each shipment. Records are provided on a monthly basis. Customer special requirement; requirement should be determined in a specific component specification.
Sample size 200
Handling Mounted on PCB
Thermal shock 1 x 280 °C, no pre-heat, 5 s to 10 s
IR - test (IRATS) U = UR, T = room temperature, verified
Burn in (BIATS)Equivalent to 12 h burn-in, 2 x UR/125 °C, verification time to failure
Sample size 20 pcs/lot
X7R, X8R Every lot
C0G At least three different part numbers of one component family matrix per quarter
Max. deflection 8 mm (data to be reported, available on request)
Revision: 23-Oct-14 60 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
5 - INSPECTION CRITERIAThe supplier shall carry out visual examination with suitable equipment with approximately 10 x magnification and lightingappropriate to the specimen under test and the required quality level.
ChippingThe components shall be free of cracks or fissures. Small damages which do not deteriorate the performance of the componentshall be less than 50 % of the surface of the MLCC as defined in EIA 595.
Delamination or Exposed ElectrodesNo visible separation or delamination between layers of the capacitor and no exposed electrodes between the two terminals ofthe capacitor must be seen.
Metallization
For the metallization, no visible detachment of the metallized terminals and no exposed electrodes must be seen. Defects andgaps in the metallization on each sides of the terminal must not exceed 10 % of the total area (e.g. A, B, C, …). Leaching shallnot exceed 25 %.
Electrode DistanceThe ceramic body shall be free of any conducting material between the terminals which reduces the distance of the electrodes.The minimum distance “D” is 400 μm for all package sizes, except 0402. For the component package 0402 the minimumdistance is 200 μm.
C
A B
D
Revision: 23-Oct-14 61 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
6 - BOARD FLEX TEST CONDITIONS
6.1 BOARD FLEX DEFINITIONS OF TESTPCB thickness = (1.6 ± 0.1) mm
Copper thickness = 35 μm
Material FR4 (EP-GC 02 according to DIN 40 802)
Note• LL = total length; LB = width of the pad; LEL = single pad length
6.2 SOLDERING INSTRUCTIONS
6.3 TYPICAL TEMPERATURE PROFILE FOR REFLOW SOLDERING (Boardflex test)
LAYOUT/PAD DESIGN (Dimensions in mm)
CASE CODEPAD SIZE
LL LB LEL0603 2.20 1.00 0.750805 3.40 1.30 1.201206 4.50 1.80 1.201210 4.50 2.80 1.301812 4.75 3.60 1.50
LEL
LL
LB
THICKNESS, RECOMMENDED FOR SOLDER PASTE (Reflow soldering)CASE CODE THICKNESS in μm
0402 75 to 900603 150 to 2000805 150 to 2001206 150 to 2001210 150 to 2001812 150 to 200
TE
MP
ER
AT
UR
E (°
C)
300
250
200
150
100
0 50 100 150 200 250 300 350 400TIME (s)
LEAD (Pb)-FREE SOLDERING PROFILE
MIN. 300 s MAX. 260 °C MIN. 255 °C
T (SOLID) MIN. 217 °C
MIN. 190 °CMIN. 40 sMIN. 90 s
RAMP UP TO 150 °CMAX. 3 K/s
RAMP DOWN FROM T (SOLID)
MAX. 6 K/sMIN. 110 s50
0
Revision: 23-Oct-14 62 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
6.4 MOUNTING, DIMENSIONS AND TESTING
6.5 PERFORMANCE OF THE TEST(S)A) Electrical test according to component specification (Cap, DF, IR)
B) Mounting to PCB
C) Storage at room temperature (min. 10 h)
D) Board flex test
6.6 DETAILS
6.7 FAILURE CRITERIA
X7R, X8R PCB to be deflected continuously, speed 1 mm/s (± 0.5 mm/s)
C0G PCB to be deflected in steps until cracks or other damages are visible or can be measured. Dwell time between steps: (5 ± 1) s
X7R, X8R Piezoelectric sensor, no failures up to min. 2 mm
C0G (NP0) C/C < 1 % or < 1 pF, no failures up to min. 2 mm
Both Electrical test according to component specification
SMD under test
Solder
Support
1.6 ± 0.1
90 ± 1
45 ± 2
Printed boardbefore test
R = 3
+ +
Mounting
+ +
Material: Aluminum20
Printed boardduring test
Width = actual widthof substrate + 5 mm on both sides
Radius1 to 2
Width
1.5 ± 0.1
0
All dimensions in mm
10 ± 0.1
Testing
Revision: 23-Oct-14 63 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....31 / VJ....34 Automotive MLCCwww.vishay.com Vishay Vitramon
7 - AEC-Q200 QUALIFICATION TESTING
NO. AEC-Q200 TEST ITEM REFERENCE
1 Pre- and post stress electrical test User spec
3 High temp exposure (storage) MIL-STD-202, method 108
4 Temperature cycling JESD22, method JA-104
5 Destructive physical analysis EIA-469
6 Moisture resistance MIL-STD-202, method 106
7 Biased humidity MIL-STD-202, method 103
8 Operation life MIL-STD-202 method 108
9 External Visual MIL-STD-883 method 2009
10 Physical dimension JESD22, method JB-100
13 Mechanical shock MIL-STD-202, method 213
14 Vibration MIL-STD-202, method 204
15 Resistance to solder heat MIL-STD-202, method 215
16 ESD AEC-Q200 rev. C
17 Solderability J-STD-002
20 Electrical characterization User spec
21 Board flex AEC-Q200-005
22 Terminal strength AEC-Q200-006
23 Beam load AEC-Q200-003
Revision: 23-Oct-14 64 Document Number: 45040For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Contents
VJ OMD Series....................... 66
VJ HVArc Guard®................... 80
VJ Source EnergyCapacitor (SEC) ..................... 88
VJ Controlled DischargeCapacitor (CDC)..................... 93
VJ Safety CertifiedCapacitors C0G (NP0) ........... 98
VJ Safety CertifiedCapacitors X7R...................... 102
MLCCsfor
High Voltage and
Safety Applications
(NME Technology)
VJ OMD Serieswww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitor Solutionsfor Boardflex Sensitive Applications
FEATURES• Open Mode Design (OMD) reduces risk of
shorts or leakage in board flex applications• Excellent reliability and thermal shock
performance• Efficient low-power consumption, ripple
current capable to 1.2 ARMS at 100 kHz• High voltage breakdown compared to
standard design• 100 % voltage conditioning available up to
630 VDC rating (process code “5H”)Contact [email protected] for higher voltages.
• Polymer termination available for intensive board flexrequirements
• Wet build process• Reliable Noble Metal Electrode (NME) system• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS• Demanding boardflex applications• Input filter capacitors• Output filter capacitors• Snubber capacitors reduce MOSFET voltage spikes• Filtering for switching power supplies• For lighting and other AC applications please contact:
ELECTRICAL SPECIFICATIONS
Available
C0G (NP0)
GENERAL SPECIFICATIONNote Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range: 10 pF to 47 nF
Voltage Range: 50 VDC to 3000 VDC
Temperature Coefficient of Capacitance (TCC):0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
Dissipation Factor (DF):0.1 % maximum at 1.0 VRMS and 1 MHz for values 1000 pF0.1 % maximum at 1.0 VRMS and 1 kHz for values > 1000 pF
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 0 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-EApplied test voltages 200 VDC-rated: 250 % of rated voltage500 VDC-rated: 200 % of rated voltage630 VDC / 1000 VDC-rated: 150 % of rated voltage1500 VDC to 3000 VDC-rated: 120 % of rated voltage
X7R
GENERAL SPECIFICATIONNote Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range: 100 pF to 1.8 μF
Voltage Range: 16 VDC to 3000 VDC
Temperature Coefficient of Capacitance (TCC):± 15 % from -55 °C to +125 °C, with 0 VDC applied
Dissipation Factor (DF):< 50 V ratings 3.5 % maximum at 1.0 VRMS and 1 kHz50 V ratings 2.5 % maximum at 1.0 VRMS and 1 kHz
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 1 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-EApplied test voltages 250 VDC-rated: 250 % of rated voltage500 VDC-rated: min. 150 % of rated voltage630 VDC / 1000 VDC-rated: 150 % of rated voltage1500 VDC to 3000 VDC-rated: 120 % of rated voltage
Revision: 01-Aug-14 66 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
Notes(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected](2) Process code with 2 digits has to be added.(3) Termination code E” is for conductive epoxy assembly.(4) Other termination options contact [email protected] for availability.
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE (V)
CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0)
1206 1500 10 pF 4.7 nF
1210 2000 10 pF 8.2 nF
1808 3000 10 pF 8.2 nF
1812 3000 10 pF 18 nF
1825 1000 15 pF 33 nF
2220 1000 270 pF 39 nF
2225 1000 270 pF 47 nF
X7R
0805 630 470 pF 220 nF
1206 2000 270 pF 680 nF
1210 2000 390 pF 1.0 μF
1808 3000 220 pF 18 nF
1812 3000 100 pF 1.2 μF
1825 2000 5.6 nF 1.5 μF
2220 3000 1.0 nF 1.8 μF
2225 2000 5.6 nF 1.8 μF
ORDERING INFORMATIONVJ1210 Y 474 J X A A T # (2)
CASECODE
DIELECTRIC CAPACITANCENOMINAL
CODE
CAPACITANCETOLERANCE
TERMINATION (4)
DCVOLTAGERATING (1)
MARKING PACKAGING PROCESSCODE
08051206121018081812182522202225
A = C0G(NP0)
Y = X7R
Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is a
multiplier. An “R”indicates a
decimal point.Examples
474 = 470 000 pF
F = ± 1 %G = ± 2 %J = ± 5 %
K = ± 10 %M = ± 20 %
NoteC0G (NP0):F, G, J, K
X7R:J, K, M
X = Ni barrier100 % tin plated
matte finishE = AgPd (3)
B = polymer 100 % tin plated
matte finish
J = 16 VX = 25 VA = 50 V
B = 100 VC = 200 VP = 250 VE = 500 VL = 630 V
G = 1000 VR = 1500 VF = 2000 VH = 3000 V
A =unmarked
4X =OMD cap
5H =OMD cap
100 %voltage
conditioning
C = 7" reel / paper tapeT = 7" reel / plastic tape P = 11 1/4" / 13" reel /
paper tapeR = 11 1/4" / 13" reel /
plastic tapeO = 7" reel / flamed
paper tapeI = 11 1/4" / 13" reel /
flamed paper tapeNote
“I” and “O” are used for“E” termination size 0805
ENVIRONMENTAL STATUSTERMINATION CODE TERMINATION DESCRIPTION RoHS COMPLIANT VISHAY GREEN
X Ni barrier 100 % tin plated matte finish Yes Yes
E AgPd Yes Yes
B Polymer layer, 100 % tin plated matte finish Yes No
Revision: 01-Aug-14 67 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
Note• Polymer (B-termination) have increased dimensions:
length 0.006" (0.15 mm)
DIMENSIONS in inches (millimeters)
CASE CODE STYLE LENGTH
(L)WIDTH
(W)
MAXIMUMTHICKNESS
(T)
TERMINATION PAD(P)
MINIMUM MAXIMUM
0805 VJ08050.079 ± 0.008(2.00 ± 0.20)
0.049 ± 0.008(1.25 ± 0.20)
0.057 (1.45) 0.010 (0.25) 0.028 (0.71)
1206 VJ12060.126 ± 0.010(3.20 ± 0.25)
0.063 ± 0.010(1.60 ± 0.25)
0.067 (1.70) 0.010 (0.25) 0.028 (0.71)
1210 VJ12100.126 ± 0.010(3.20 ± 0.25)
0.098 ± 0.010(2.50 ± 0.25)
0.067 (1.70) 0.010 (0.25) 0.028 (0.71)
1808 VJ18080.180 ± 0.012(4.57 ± 0.30)
0.080 ± 0.010(2.03 ± 0.25)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
1812 VJ18120.177 ± 0.012(4.50 ± 0.30)
0.126 ± 0.008(3.20 ± 0.20)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
1825 VJ18250.177 ± 0.012(4.50 ± 0.30)
0.252 ± 0.010(6.40 ± 0.25)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
2220 VJ22200.220 ± 0.010(5.59 ± 0.25)
0.200 ± 0.010(5.08 ± 0.25)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
2225 VJ22250.220 ± 0.010(5.59 ± 0.25)
0.250 ± 0.010(6.35 ± 0.25)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
LW
TMAX.
P
Revision: 01-Aug-14 68 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1206 (1) VJ1210 (1) VJ1808 (1)
CASE CODE 1206 1210 1808VOLTAGE (VDC) 50 100 200 500 630 1000 1500 50 100 200 500 630 1000 1500 2000 50 100 200 500 630 1000 1500 2000 3000 VOLTAGE CODE A B C E L G R A B C E L G R F A B C E L G R F HCAP. CODE CAP.100 10 pF • • • • • • • • • • • • • • • • • • • • • • • •120 12 pF • • • • • • • • • • • • • • • • • • • • • • • •150 15 pF • • • • • • • • • • • • • • • • • • • • • • • •180 18 pF • • • • • • • • • • • • • • • • • • • • • • • •220 22 pF • • • • • • • • • • • • • • • • • • • • • • • •270 27 pF • • • • • • • • • • • • • • • • • • • • • • • •330 33 pF • • • • • • • • • • • • • • • • • • • • • • • •390 39 pF • • • • • • • • • • • • • • • • • • • • • • •470 47 pF • • • • • • • • • • • • • • • • • • • • • • •560 56 pF • • • • • • • • • • • • • • • • • • • • • • •680 68 pF • • • • • • • • • • • • • • • • • • • • • • •820 82 pF • • • • • • • • • • • • • • • • • • • • • • •101 100 pF • • • • • • • • • • • • • • • • • • • • • • •121 120 pF • • • • • • • • • • • • • • • • • • • • • •151 150 pF • • • • • • • • • • • • • • • • •181 180 pF • • • • • • • • • • • • • • • • •221 220 pF • • • • • • • • • • • • • • • • •271 270 pF • • • • • • • • • • • • • • •331 330 pF • • • • • • • • • • • • • • •391 390 pF • • • • • • • • • • • • • • •471 470 pF • • • • • • • • • • • • • • •561 560 pF • • • • • • • • • • • • • • •681 680 pF • • • • • • • • • • • • • • •821 820 pF • • • • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • •152 1.5 nF • • • • • • • • • •182 1.8 nF • • • • • • • • •222 2.2 nF • • • • • • • • •272 2.7 nF • • • • • • • •332 3.3 nF • • • • • • • •392 3.9 nF • • • • • • •472 4.7 nF • • • • • • •562 5.6 nF • • • •682 6.8 nF • • •822 8.2 nF • •103 10 nF123 12 nF153 15 nF183 18 nF223 22 nF273 27 nF333 33 nF393 39 nF473 47 nF563 56 nF683 68 nF823 82 nF104 100 nF
Revision: 01-Aug-14 69 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1812 (1) VJ1825 (1)
CASE CODE 1812 1825VOLTAGE (VDC) 50 100 200 500 630 1000 1500 2000 3000 50 100 200 500 630 1000VOLTAGE CODE A B C E L G R F H A B C E L GCAP. CODE CAP.100 10 pF • • • • • • • • •120 12 pF • • • • • • • • •150 15 pF • • • • • • • • • • •180 18 pF • • • • • • • • • • •220 22 pF • • • • • • • • • • •270 27 pF • • • • • • • • • • •330 33 pF • • • • • • • • • • • • • • •390 39 pF • • • • • • • • • • • • • • •470 47 pF • • • • • • • • • • • • • • •560 56 pF • • • • • • • • • • • • • • •680 68 pF • • • • • • • • • • • • • • •820 82 pF • • • • • • • • • • • • • • •101 100 pF • • • • • • • • • • • • • • •121 120 pF • • • • • • • • • • • • • • •151 150 pF • • • • • • • • • • • • • • •181 180 pF • • • • • • • • • • • • • • •221 220 pF • • • • • • • • • • • • • • •271 270 pF • • • • • • • • • • • • • • •331 330 pF • • • • • • • • • • • • • • •391 390 pF • • • • • • • • • • • • • •471 470 pF • • • • • • • • • • • • • •561 560 pF • • • • • • • • • • • • • •681 680 pF • • • • • • • • • • • • • •821 820 pF • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • •272 2.7 nF • • • • • • • •332 3.3 nF • • • • • • • •392 3.9 nF • • • • • • • •472 4.7 nF • • • • • • •562 5.6 nF • • • • • • •682 6.8 nF • • • • • • •822 8.2 nF • • • • • • •103 10 nF • • • • • •123 12 nF • • • • •153 15 nF • • • •183 18 nF • • • •223 22 nF • • •273 27 nF • •333 33 nF •393 39 nF473 47 nF563 56 nF683 68 nF823 82 nF104 100 nF
Revision: 01-Aug-14 70 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC C0G (NP0)
STYLE VJ2220 (1) VJ2225 (1)
CASE CODE 2220 2225 VOLTAGE (VDC) 50 100 200 500 630 1000 50 100 200 500 630 1000VOLTAGE CODE A B C E L G A B C E L GCAP. CODE CAP.100 10 pF120 12 pF150 15 pF180 18 pF220 22 pF270 27 pF330 33 pF390 39 pF470 47 pF560 56 pF680 68 pF820 82 pF101 100 pF121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF • • • • • • • • • • • •331 330 pF • • • • • • • • • • • •391 390 pF • • • • • • • • • • • •471 470 pF • • • • • • • • • • • •561 560 pF • • • • • • • • • • • •681 680 pF • • • • • • • • • • • •821 820 pF • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • •562 5.6 nF • • • • • • •682 6.8 nF • • • • • • •822 8.2 nF • • • • • • •103 10 nF • • • • • • •123 12 nF • • • • • • •153 15 nF • • • • •183 18 nF • • • • •223 22 nF • • • • •273 27 nF • • • • •333 33 nF • • • •393 39 nF • • •473 47 nF •563 56 nF683 68 nF823 82 nF104 100 nF
Revision: 01-Aug-14 71 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Paper tape • Plastic tape(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC X7RSTYLE VJ0805 (1) VJ1206 (1)
CASE CODE 0805 1206 VOLTAGE (VDC) 16 25 50 100 200 500 630 16 25 50 100 200 500 630 1000 1500 2000VOLTAGE CODE J X A B C E L J X A B C E L G R FCAP. CODE CAP.101 100 pF121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF • • • • • • • • • •331 330 pF • • • • • • • • • •391 390 pF • • • • • • • • • •471 470 pF •• •• •• •• •• • • • • • • • • • • • •561 560 pF •• •• •• •• •• • • • • • • • • • • • •681 680 pF •• •• •• •• •• • • • • • • • • • • • •821 820 pF •• •• •• •• •• • • • • • • • • • • • •102 1.0 nF •• •• •• •• •• • • • • • • • • • • • •122 1.2 nF •• •• •• •• •• • • • • • • • • • • •152 1.5 nF •• •• •• •• •• • • • • • • • • • • •182 1.8 nF •• •• •• •• •• • • • • • • • • • • •222 2.2 nF •• •• •• •• •• • • • • • • • • • •272 2.7 nF •• •• •• •• •• • • • • • • • • • •332 3.3 nF •• •• •• •• •• • • • • • • • • • •392 3.9 nF •• •• •• •• •• • • • • • • • • • •472 4.7 nF •• •• •• •• •• • • • • • • • • • •562 5.6 nF •• •• •• •• • • • • • • • •682 6.8 nF •• •• •• •• • • • • • • • •822 8.2 nF •• •• •• •• • • • • • • • •103 10 nF •• •• •• •• • • • • • • • •123 12 nF •• •• •• • • • • • • • • •153 15 nF •• •• •• • • • • • • • • •183 18 nF •• •• •• • • • • • • • • •223 22 nF •• •• •• • • • • • • •273 27 nF • • • • • • • • •333 33 nF • • • • • • • • •393 39 nF • • • • • • • • •473 47 nF • • • • • • • • •563 56 nF • • • • • • • •683 68 nF • • • • • • • •823 82 nF • • • • • • • •104 100 nF • • • • • • •124 120 nF • • • • • •154 150 nF • • • • • •184 180 nF • • • • •224 220 nF • • • •274 270 nF • • •334 330 nF • • •394 390 nF • •474 470 nF • •564 560 nF •684 680 nF •824 820 nF105 1.0 μF125 1.2 μF155 1.5 μF185 1.8 μF225 2.2 μF
Revision: 01-Aug-14 72 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC X7R STYLE VJ1210 (1) VJ1808 (1)
CASE CODE 1210 1808 VOLTAGE (VDC) 16 25 50 100 200 500 630 1000 1500 2000 630 1000 1500 2000 3000VOLTAGE CODE J X A B C E L G R F L G R F HCAP. CODE CAP.101 100 pF121 120 pF151 150 pF181 180 pF221 220 pF •271 270 pF •331 330 pF •391 390 pF • • • •471 470 pF • • • • • • • •561 560 pF • • • • • • • •681 680 pF • • • • • • • •821 820 pF • • • • • • • •102 1.0 nF • • • • • • • •122 1.2 nF • • • • • • • •152 1.5 nF • • • • • • • •182 1.8 nF • • • • • • •222 2.2 nF • • • • • • •272 2.7 nF • • • • • • •332 3.3 nF • • • • • • •392 3.9 nF • • • • •472 4.7 nF • • • • •562 5.6 nF • • • •682 6.8 nF • • • •822 8.2 nF • • •103 10 nF • • • • • • • • • •123 12 nF • • • • • • • • •153 15 nF • • • • • • • • •183 18 nF • • • • • • • • •223 22 nF • • • • • • •273 27 nF • • • • • • •333 33 nF • • • • • • •393 39 nF • • • • • • •473 47 nF • • • • •563 56 nF • • • • •683 68 nF • • • • •823 82 nF • • • • •104 100 nF • • • • •124 120 nF • • • • •154 150 nF • • • • •184 180 nF • • • •224 220 nF • • • •274 270 nF • • • •334 330 nF • • • •394 390 nF • • • •474 470 nF • • • •564 560 nF • • •684 680 nF • • •824 820 nF • •105 1.0 μF •125 1.2 μF155 1.5 μF185 1.8 μF225 2.2 μF
Revision: 01-Aug-14 73 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC X7R STYLE VJ1812 (1) VJ1825 (1)
CASE CODE 1812 1825 VOLTAGE (VDC) 50 100 200 250 500 630 1000 1500 2000 3000 100 200 500 630 1000 1500 2000VOLTAGE CODE A B C P E L G R F H B C E L G R FCAP. CODE CAP.101 100 pF • • • • •121 120 pF • • • • •151 150 pF • • • • •181 180 pF • • • • •221 220 pF • • • • •271 270 pF • • • • • •331 330 pF • • • • • •391 390 pF • • • • • • • • • •471 470 pF • • • • • • • • • •561 560 pF • • • • • • • • • •681 680 pF • • • • • • • • • •821 820 pF • • • • • • • • • •102 1.0 nF • • • • • • • • • •122 1.2 nF • • • • • • • • • •152 1.5 nF • • • • • • • • • •182 1.8 nF • • • • • • • • • •222 2.2 nF • • • • • • • • • •272 2.7 nF • • • • • • • • •332 3.3 nF • • • • • • • • •392 3.9 nF • • • • • • • • •472 4.7 nF • • • • • • • • •562 5.6 nF • • • • • • • • • • •682 6.8 nF • • • • • • • • • • •822 8.2 nF • • • • • • • • • •103 10 nF • • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • •203 20 nF • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • •393 39 nF • • • • • • • • • • •473 47 nF • • • • • • • • • • •563 56 nF • • • • • • • • • • •683 68 nF • • • • • • • • • •823 82 nF • • • • • • • • • •104 100 nF • • • • • • • • •124 120 nF • • • • • • • •154 150 nF • • • • • • • •184 180 nF • • • • • • •224 220 nF • • • • • • •274 270 nF • • • • • •334 330 nF • • • • • •394 390 nF • • • • •474 470 nF • • • •564 560 nF • • • •684 680 nF • • • •824 820 nF • • •105 1.0 μF • • •125 1.2 μF • •155 1.5 μF •185 1.8 μF225 2.2 μF
Revision: 01-Aug-14 74 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant
(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC X7RSTYLE VJ2220 (1) VJ2225 (1) CASE CODE 2220 2225 VOLTAGE (VDC) 50 100 200 250 500 630 1000 2000 3000 100 200 500 630 1000 1500 2000VOLTAGE CODE A B C P E L G F H B C E L G R FCAP. CODE CAP.101 100 pF121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF331 330 pF391 390 pF471 470 pF561 560 pF681 680 pF821 820 pF102 1.0 nF •122 1.2 nF •152 1.5 nF •182 1.8 nF •222 2.2 nF •272 2.7 nF332 3.3 nF392 3.9 nF472 4.7 nF562 5.6 nF • • •682 6.8 nF • • •822 8.2 nF • • •103 10 nF • • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • • •203 20 nF • • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • • • •393 39 nF • • • • • • • • • • • • • •473 47 nF • • • • • • • • • • • • • •563 56 nF • • • • • • • • • • • •683 68 nF • • • • • • • • • • • •823 82 nF • • • • • • • • • • • •104 100 nF • • • • • • • • • • •124 120 nF • • • • • • • • •154 150 nF • • • • • • • • •184 180 nF • • • • • • • • •224 220 nF • • • • • • • • •274 270 nF • • • • • • •334 330 nF • • • • • • •394 390 nF • • • • • •474 470 nF • • • • • •564 560 nF • • • • • •684 680 nF • • • • • •824 820 nF • • • •105 1.0 μF • • • •125 1.2 μF • • • •155 1.5 μF • • •185 1.8 μF • •225 2.2 μF
Revision: 01-Aug-14 75 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
C0G (NP0) CAPACITORS - TYPICAL PARAMETERS
- 75 - 50 - 25 0 25 50 75 100 125
2.0
1.5
1.0
0.5
0.0
- 0.5
- 1.0
- 1.5
- 2.0
NP0
TEMPERATURE °C
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE COEFFICIENT OF CAPACITANCE
TEMPERATURE °C
10 25 100 125
10 000
1000
100
10
INS
UL
AT
ION
RE
SIS
TAN
CE
(ΩF
)
MIN. INSULATION RESISTANCE VS. TEMPERATURE
AGING RATE
HOURS
1 10 100 1000 10 000
0.2
0.1
0.0
- 0.1
- 0.2
% C
APA
CIT
AN
CE
CH
AN
GE
0 100 200 300 400 500 600 700 800 900 1000
10
0
- 20
- 30
DC VOLTS APPLIED
% C
APA
CIT
AN
CE
CH
AN
GE
- 10
20
30
VOLTAGE COEFFICIENT OF CAPACITANCE
Revision: 01-Aug-14 76 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
X7R DIELECTRIC - TYPICAL PARAMETERS
100
50
TEMPERATURE °C
% R
AT
ED
VO
LT
AG
E
0
RATED VOLTAGE VS. TEMPERATURE
150
200
- 75 - 50 - 25 0 20 50 75 100 125 150 175 1800.0
DISSIPATION FACTOR VS. TEMPERATURE
TEMPERATURE °C
% D
ISS
IPA
TIO
N F
AC
TO
R
0.51.01.52.02.53.03.54.04.55.05.56.0
- 75 - 50 - 25 0 25 50 75 100 125 150 175
X7R
X5R
VOLTAGE COEFFICIENT OF CAPACITANCE
% C
APA
CIT
AN
CE
CH
AN
GE
10
0
- 10
- 20
- 30
- 40
- 50
- 60
- 70
- 800 500 1000 1500 2000 2500
DC VOLTS APPLIED
630 V/1000 V/1500 V Rated2000 V Rated
DISSIPATION FACTOR VS. VOLTAGE
0 100 200 300 400 500 600 700 UN/V-
0.020
0.016
0.012
0.008
0.000500/630 V
200 V
DC VOLTS APPLIED
DIS
SIP
AT
ION
FA
CT
OR
IMPEDANCE VS. FREQUENCY 500 V/630 V
FREQUENCY (MHz)
0.01 0.1 1 10 100
1000
100
10
1
0.1
0.01
IMP
ED
AN
CE
(Ω
)
1 µF 0.1 µF 0.01 µF
IMPEDANCE VS. FREQUENCY 2000 V
FREQUENCY (MHz)
IMP
ED
AN
CE
(Ω
)
0.1
1000
1 10 100 1000
100
10
1
4.7 nF 2.2 nF 1 nF
Revision: 01-Aug-14 77 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
X7R DIELECTRIC - TYPICAL PARAMETERS
DC VOLTS APPLIED
% C
APA
CIT
AN
CE
CH
AN
GE
10
0
- 10
- 20
- 30
- 40
- 50
- 60
- 70
- 80
VOLTAGE COEFFICIENT OF CAPACITANCE LOWER CAPACITANCE
0 100 200 300 400 500 600 700
Case Size1206121018081812
Range100 pF to 4700 pF390 pF to 10 000 pF470 pF to 18 000 pF1000 pF to 27 000 pF
DC VOLTS APPLIED
% C
AP
AC
ITA
NC
E C
HA
NG
E
10
0
- 10
- 20
- 30
- 40
- 50
- 60
- 70
- 80
- 90
VOLTAGE COEFFICIENT OF CAPACITANCE HIGHER CAPACITANCE
0 100 200 300 400 500 600 700
Case Size120612101812
Range5600 pF to 18 000 pF12 000 pF to 39 000 pF33 000 pF to 100 000 pF
VOLTAGE COEFFICIENT OF CAPACITANCE
DC VOLTS APPLIED
% C
APA
CIT
AN
CE
CH
AN
GE
0 500 1000 1500 2000 2500
10
0
- 10
- 20
- 30
- 40
- 50
- 60
- 70
- 80
1000 V/1500 V RATED2000 V RATED
Revision: 01-Aug-14 78 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ OMD Serieswww.vishay.com Vishay Vitramon
BOARDFLEX SENSITIVE APPLICATIONS - SOLUTIONA predominant failure mode in multilayer ceramic chip capacitors is cracking caused by board flexure. Cracks can then createa path for current to pass from one electrode through the dielectric to an opposing electrode or from the terminations at oneend of the MLCC through the dielectric to an opposing electrode. This may subsequently result in capacitance loss, leakage -low Insulation Resistance (IR) - and / or more seriously, high current shorts. A short circuit condition in the surface mountedcapacitors can cause further failures of downstream components. Vishay’s Open Mode Design Capacitors (VJ OMD - Cap.series) reduce the risk of these destructive conditions through MLCC designs that prevent board flexure cracks reaching theopposing electrode.VJ OMD - Cap. MLCCs reduce the risk of early field failures associated with board flex cracks. However, it is important to notethat even in the open mode designs the presence of flexure related cracks can cause capacitance loss leading to localizedstresses on the parts. eventually, depending on the application environment, including such factors and high voltage pulsefrequency and thermal cycling this may lead to internal breakdown of the component.
POLYMER TERMINATIONPolymer termination provides additional protection against board flexure damage by absorbing greater mechanical and thermalstresses. Components can be packaged, transported, stored and handled the same standard terminated product. Wave andreflow soldering of MLCC does not require modification to equipment and / or process. Polymer termination greatly reduces therisk of mechanical cracking however it does not completely eliminate.
Notes(1) Vishay Vitramon uses embossed plastic, and punch paper carrier tapes. Paper tape is not available for case sizes 1206 or for component
thickness > 0.035" (0.89 mm)(2) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(3) n/a = not available(4) Packaging code “C / O”, “P / I” and lower quantities can depend from product thickness
STANDARD TERMINATION OMD CAP PLUS POLYMER TERMINATIONExposed Electrodes = Electrical Short No Exposed Electrodes = No Electrical Short
STANDARD PACKAGING QUANTITIES (1)(2)(3)
CASECODE
TAPESIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PAPER TAPE PACKAGING CODE “C” / “O”
PLASTIC TAPE PACKAGING CODE “T”
PAPER TAPEPACKAGING CODE “P” / “I”
PLASTIC TAPE PACKAGING CODE “R”
0805 (4) 8 mm 3000 3000 10 000 10 0001206 (4) 8 mm n/a 2500 / 3000 n/a 9000 / 10 0001210 (4) 8 mm n/a 2000 / 2500 / 3000 n/a 9000 / 10 0001808 (4) 12 mm n/a 2000 n/a 10 0001812 (4) 12 mm n/a 1000 n/a 40001825 12 mm n/a 1000 n/a 40002220 12 mm n/a 1000 n/a 40002225 12 mm n/a 1000 n/a 4000
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to 40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 01-Aug-14 79 Document Number: 45198For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HVArc Guard®
www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip CapacitorsProhibit Surface Arc-Over in High-Voltage Applications
FEATURESFor this Worldwide Patented Technology• Specialty: high-voltage applications• MLCC that protects against surface arc-over• Excellent high-voltage performance• Higher capacitances and smaller case sizes that
save board space, as compared to standardhigh-voltage MLCCs
• Voltage breakdowns as much as twice that of competitors’ products• Available with polymer termination for increase resistance to
board flex cracking. Please contact factory for availability• Wet build process• Reliable Noble Metal Electrode (NME) system • Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS• Power supplies• DC/DC converters (buck and boost)• Voltage multipliers for flyback converters• For lighting and other AC applications please contact:
ELECTRICAL SPECIFICATIONS
Available
C0G (NP0)
GENERAL SPECIFICATIONNote Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range: 10 pF to 8.2 nF
Voltage Range: 1000 VDC to 2500 VDC
Temperature Coefficient of Capacitance (TCC):0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
Dissipation Factor (DF):0.1 % maximum at 1.0 VRMS and 1 MHz for values 1000 pF0.1 % maximum at 1.0 VRMS and 1 kHz for values > 1000 pF
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 0 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages1000 VDC-rated: 150 % of rated voltage1500 VDC, 2500 VDC-rated: 120 % of rated voltage
X7R
GENERAL SPECIFICATIONNote Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range: 220 pF to 270 nF
Voltage Range: 250 VDC to 1000 VDC
Temperature Coefficient of Capacitance (TCC):± 15 % from -55 °C to +125 °C, with 0 VDC applied
Dissipation Factor (DF):2.5 % maximum at 1.0 VRMS and 1 kHz
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 1 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 250 VDC-rated: 200 % of rated voltage500 VDC-rated: min. 150 % of rated voltage630 VDC, 1000 VDC-rated: min. 120 % of rated voltage
Revision: 05-Nov-14 80 Document Number: 45197For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HVArc Guard®
www.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
Notes(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected](2) Process code has to be added.(3) Termination code “E” is for conductive epoxy assembly, contact [email protected] for availability.(4) Please contact factory for polymer termination availability(5) “5ZL” mandatory for size 1206 / 1210 in C0G (NP0) with 1000 V / 1500 V for capacitance < 100 pF and used for other specific part numbers,
consult for questions [email protected].(6) Other termination options contact [email protected] for availability.
Note(1) “No” for size 1206 / 1210 in C0G (NP0) with 1000 V / 1500 V for capacitance < 100 pF.
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE (V)
CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0)
0805 1500 10 pF 390 pF
1206 1500 10 pF 1.5 nF
1210 1500 10 pF 2.7 nF
2220 1500 470 pF 5.6 nF
2225 2500 470 pF 8.2 nF
X7R
0805 1000 470 pF 3.3 nF
1206 1000 220 pF 47 nF
1210 1000 220 pF 82 nF
1808 1000 220 pF 100 nF
1812 1000 220 pF 270 nF
ORDERING INFORMATION (4)
VJ0805 A 101 J X G A T 5Z (2)
CASECODE
DIELECTRIC CAPACITANCENOMINAL
CODE
CAPACITANCETOLERANCE
TERMINATION(6)
DCVOLTAGERATING (1)
MARKING PACKAGING PROCESSCODE
0805120612101808181222202225
A = C0G(NP0)
Y = X7R
Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is amultiplier.Examples
102 = 1000 pF223 = 22 000 pF
J = ± 5 % K = ± 10 %M = ± 20 %
X = Ni barrier 100 % matte tin
plate finishF, E = AgPd (3)
B = polymer100 % matte tin
plate finish (4)
P = 250 VE = 500 VL = 630 V
G = 1000 VR = 1500 VO = 2500 V
A =unmarked
5Z / 5ZL (5) = HVArcGuard®
T = 7" reel / plastic tape R = 11 1/4" / 13" reel / plastic tape
ENVIRONMENTAL STATUSTERMINATION CODE TERMINATION DESCRIPTION RoHS COMPLIANT VISHAY GREEN
X Ni barrier 100 % tin plated matte finish Yes Yes / No (1)
E AgPd Yes Yes / No (1)
B Polymer layer, 100 % tin plated matte finish Yes No
F AgPd Yes No
Revision: 05-Nov-14 81 Document Number: 45197For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HVArc Guard®
www.vishay.com Vishay Vitramon
Note• Polymer (B-termination) have increased dimensions:
part length increased by 0.006" (0.15 mm)
DIMENSIONS in inches (millimeters)
CASECODE STYLE LENGTH
(L)WIDTH
(W)
MAXIMUMTHICKNESS
(T)
TERMINATION PAD (P)
MINIMUM MAXIMUM
0805 VJ08050.079 ± 0.008(2.00 ± 0.20)
0.049 ± 0.008(1.25 ± 0.020)
0.057 (1.45) 0.010 (0.25) 0.028 (0.71)
1206 VJ12060.126 ± 0.008(3.20 ± 0.20)
0.063 ± 0.008(1.60 ± 0.20)
0.067 (1.70) 0.010 (0.25) 0.030 (0.76)
1210 VJ12100.126 ± 0.008(3.20 ± 0.20)
0.098 ± 0.008(2.50 ± 0.020)
0.067 (1.70) 0.010 (0.25) 0.030 (0.76)
1808 VJ18080.180 ± 0.012(4.57 ± 0.30)
0.080 ± 0.010 (2.03 ± 0.25)
0.067 (1.70) 0.010 (0.25) 0.030 (0.76)
1812 VJ18120.177 ± 0.012(4.50 ± 0.30)
0.126 ± 0.008(3.20 ± 0.20)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
2220 VJ22200.220 ± 0.010(5.59 ± 0.25)
0.200 ± 0.010 (5.08 ± 0.25)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
2225 VJ22250.220 ± 0.010(5.59 ± 0.25)
0.250 ± 0.010 (6.35 ± 0.25)
0.090 (2.30) 0.010 (0.25) 0.030 (0.76)
LW
TMAX.
P
Revision: 05-Nov-14 82 Document Number: 45197For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HVArc Guard®
www.vishay.com Vishay Vitramon
Notes(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034• Available in plastic carrier tape only
RoHS-compliant
SELECTION CHART C0G (NP0) DIELECTRIC C0G (NP0)
STYLE VJ0805 VJ1206 (1) VJ1210 (1) VJ2220 (1) VJ2225 (1)
CASE CODE 0805 1206 1210 2220 2225
VOLTAGE (VDC) 1000 1500 1000 1500 1000 1500 1000 1500 1000 1500 2500
VOLTAGE CODE G R G R G R G R G R O
CAP. CODE CAP.
100 10 pF • • • • • •
120 12 pF • • • • • •
150 15 pF • • • • • •
180 18 pF • • • • • •
220 22 pF • • • • • •
270 27 pF • • • • • •
330 33 pF • • • • • •
390 39 pF • • • • • •
470 47 pF • • • • • •
560 56 pF • • • • • •
680 68 pF • • • • • •
820 82 pF • • • • • •
101 100 pF • • • • • •
121 120 pF • • • • • •
151 150 pF • • • • • •
181 180 pF • • • • • •
221 220 pF • • • • • •
271 270 pF • • • • • •
331 330 pF • • • • • •
391 390 pF • • • • • •
471 470 pF • • • • • • • • •
561 560 pF • • • • • • • • •
681 680 pF • • • • • • • • •
821 820 pF • • • • • • • • •
102 1.0 nF • • • • • • • • •
122 1.2 nF • • • • • • • • •
152 1.5 nF • • • • • • • • •
182 1.8 nF • • • • • • •
222 2.2 nF • • • • • • •
272 2.7 nF • • • • • • •
332 3.3 nF • • • • •
392 3.9 nF • • • • •
472 4.7 nF • • • • •
562 5.6 nF • • • • •
682 6.8 nF • • •
822 8.2 nF • • •
Revision: 05-Nov-14 83 Document Number: 45197For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HVArc Guard®
www.vishay.com Vishay Vitramon
Notes(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034• Available in plastic carrier tape only
RoHS-compliant
SELECTION CHART X7RDIELECTRIC X7RSTYLE VJ0805 VJ1206 (1) VJ1210 (1) VJ1808 (1) VJ1812 (1)
CASE CODE 0805 1206 1210 1808 1812VOLTAGE (VDC) 630 1000 250 500 630 1000 250 500 630 1000 250 500 630 1000 250 500 630 1000VOLTAGE CODE L G P E L G P E L G P E L G P E L GCAP. CODE CAP.101 100 pF 121 120 pF 151 150 pF 181 180 pF 221 220 pF • • • • • • • • • • • • • • • •271 270 pF • • • • • • • • • • • • • • • •331 330 pF • • • • • • • • • • • • • • • •391 390 pF • • • • • • • • • • • • • • • •471 470 pF • • • • • • • • • • • • • • • • • •561 560 pF • • • • • • • • • • • • • • • • • •681 680 pF • • • • • • • • • • • • • • • • • •821 820 pF • • • • • • • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • • • • • •562 5.6 nF • • • • • • • • • • • • • • • •682 6.8 nF • • • • • • • • • • • • • • • •822 8.2 nF • • • • • • • • • • • • • • • •103 10 nF • • • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • • • •393 39 nF • • • • • • • • • • • • • •473 47 nF • • • • • • • • • • • • • •563 56 nF • • • • • • • •683 68 nF • • • • • •823 82 nF • • • • • •104 100 nF • • • •124 120 nF •154 150 nF •184 180 nF •224 220 nF •274 270 nF •334 330 nF
Revision: 05-Nov-14 84 Document Number: 45197For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HVArc Guard®
www.vishay.com Vishay Vitramon
HVArc Guard® C0G (NP0) DIELECTRIC - TYPICAL PARAMETERS
-75 -50 -25 0 25 50 75 100 125
2.0
1.5
1.0
0.5
0.0
-0.5
-1.0
-1.5
-2.0
NP0
TEMPERATURE °C
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE COEFFICIENT OF CAPACITANCE
TEMPERATURE °C
10 25 100 125
10 000
1000
100
10
INS
UL
AT
ION
RE
SIS
TA
NC
E(Ω
F)
MINIMUM INSULATION RESISTANCE VS. TEMPERATURE
AGING RATE
HOURS
101 100 1000 10 000
0.2
0.1
0.0
-0.1
- 0.2
% C
APA
CIT
AN
CE
CH
AN
GE
0.2
0.1
0.0
-0.1
-0.2
DC VOLTS APPLIED
VOLTAGE COEFFICIENT OF CAPACITANCE%
CA
PA
CIT
AN
CE
CH
AN
GE
0 10 20 30 40 50 60 70 80 90 100
0.01
0.1
1
10
100
1000
1 10 100 1000
FREQUENCY (MHz)
IMP
ED
AN
CE
(Ω
)
IMPEDANCE VS. FREQUENCY OF 1206 NP0 HVArc Guard®
470 pF
1000 pF
Revision: 05-Nov-14 85 Document Number: 45197For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HVArc Guard®
www.vishay.com Vishay Vitramon
HVArc Guard® X7R DIELECTRIC - TYPICAL PARAMETERS
-20
-15
-10
-5
0
5
10
15
-100 -50 0 50 100 150
TEMPERATURE COEFFICIENT OF CAPACITANCE
% C
AP
AC
ITA
NC
E C
HA
NG
E
TEMPERATURE °C TEMPERATURE ° C
10 25 100 125
10 000
1000
100
10
INS
UL
AT
ION
RE
SIS
TAN
CE
(Ω
F)
MINIMUM INSULATION RESISTANCE VS. TEMPERATURE
AGING RATE
HOURS
1.0
0.0
-1.0
-2.0
% C
AP
AC
ITA
NC
E C
HA
NG
E
-3.0
-4.01 10 100 1000 10 000
0
0.5
1.0
1.5
2.0
2.5
3.0
-100 -50 0 50 100 150
DISSIPATION FACTOR VS. TEMPERATURE%
DIS
SIP
AT
ION
FA
CT
OR
TEMPERATURE °C
IMPEDANCE VS. FREQUENCY OF 1206 HVArc Guard® CAPACITORS
0.01
0.1
1
10
100
1 10 100FREQUENCY (MHz)
IMP
ED
AN
CE
(Ω
)
1000
33 nF 22 nF 15 nF
Revision: 05-Nov-14 86 Document Number: 45197For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HVArc Guard®
www.vishay.com Vishay Vitramon
Notes(1) Vishay Vitramon uses embossed plastic carrier tape(2) 11 1/4" reel is standard for large quantities. 13" is maybe used for large “T” dimension parts(3) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(4) Packaging quantity can vary with product thickness
Contact [email protected] with respect to specific part number requirements
TYPICAL C0G (NP0) VOLTAGE BREAKDOWN TYPICAL X7R VOLTAGE BREAKDOWN
TYPICAL ARCING ON MLCCS (shown in polarized light)Crack caused by surface arc from end termination to top electrode
layer cause component failureCorona traces due to arc-over become conductive paths leading to
component failure
APPLICATION NOTE• Suitable only for transient voltage and not for periodical pulse(s) chain• 1000 V rated parts are not suitable for AC / lighting applications above 220 VAC• 500 V and 630 V are not suitable for AC / lighting applications above 110 VAC• If further questions, please contact: [email protected]
STANDARD PACKAGING QUANTITIES (1)(2)(3)
CASE CODE TAPE SIZE7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PLASTIC TAPE PACKAGING CODE “T”
PLASTIC TAPE PACKAGING CODE“R”
0805 8 mm 3000 10 0001206 (4) 8 mm 2500 10 0001210 (4) 8 mm 2500 10 0001808 12 mm 2000 10 0001812 12 mm 1000 40002220 12 mm 1000 40002225 12 mm 1000 4000
STORAGE AND HANDLING CONDITIONS(1) Store the components at 5 °C to 40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
TYPICAL C0G (NP0) VOLTAGE BREAKDOWN(n = 50, 500 V/s applied)
20002100220023002400250026002700280029003000
1000 V 1500 V
PART RATED VOLTAGE
AV
ER
AG
E V
OLT
AG
EB
RE
AK
DO
WN
(VD
C)
TYPICAL X7R VOLTAGE BREAKDOWN (n = 50, 500 V/s applied)
0 500
100015002000250030003500
250 VDC 500 VDC 1000 VDC
PART RATED VOLTAGE
AV
ER
AG
E V
OLT
AG
EB
RE
AK
DO
WN
(VD
C)
HVArc Guard® HVArc Guard®
Co
mp
etitor
Revision: 05-Nov-14 87 Document Number: 45197For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Source Energy Capacitor (SEC)www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Capacitors for Pulse Current Applications
FEATURES• Low electrostrictive ceramic formulation for
repeated charge and discharge cycles
• High pulse discharge currents
• Excellent reliability and high voltage performance
• Available with tin / lead barrier termination (code “L”)
• Wet built process
• Reliable Noble Metal Electrode (NME) system
• Made with a combination of design, materials and tightprocess control to achieve very high field reliability
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
Note* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information / tables in this datasheet for details.
APPLICATIONS• Power supplies
• Converters
• Voltage multipliers
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range: 4.7 nF to 560 nF
Voltage Range: 1000 VDC, 1500 VDC
Temperature Coefficient of Capacitance (TCC): X7R: ± 15 % from -55 °C to +125 °C, with 0 VDC applied
Dissipation Factor (DF): 2.5 % max. at 1.0 VRMS and 1 kHz
Aging Rate: 1 % maximum per decade
Insulation Resistance (IR): at +25 °C and rated voltage: 100 000 M minimum or1000 F, whichever is lessat +125 °C and rated voltage: 10 000 M minimum or100 F, whichever is less
Dielectric Strength Test:performed per method 103 of EIA 198-2-E. Applied test voltages: 1000 VDC / 1500 VDC-rated: min. 120 % of rated voltage
Available
Available
Revision: 10-Feb-15 88 Document Number: 45210For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Source Energy Capacitor (SEC)www.vishay.com Vishay Vitramon
Note(1) Thickness used for 3640 - 1500 V - 220 nF and 270 nF
Note• Detail ratings see “Selection Chart”
Notes(1) DC voltage rating should not be exceeded in application.(2) Process code with 2 digits has to be added.(3) All types of packaging may not be available for all case sizes, see table end of this datasheet.
DIMENSIONS in inches [millimeters]
CASE CODEPART
ORDERINGNUMBER
LENGTH(L)
WIDTH(W)
MAXIMUM THICKNESS(T)
TERMINATION(P)
MINIMUM MAXIMUM
1812 VJ1812 0.177 ± 0.012[4.50 ± 0.30]
0.126 ± 0.008[3.20 ± 0.20]
0.086 [2.18]
0.010[0.25]
0.030[0.76]
1825 VJ1825 0.177 ± 0.012[4.50 ± 0.30]
0.252 ± 0.010[6.40 ± 0.25]
0.086 [2.18]
0.010[0.25]
0.030[0.76]
2225 VJ2225 0.220 ± 0.010[5.59 ± 0.25]
0.250 ± 0.010[6.35 ± 0.25]
0.086 [2.18]
0.010[0.25]
0.030[0.76]
3040 VJ3040 0.300 ± 0.015[7.62 ± 0.38]
0.400 ± 0.015[10.20 ± 0.38]
0.100[2.54]
0.010[0.25]
0.030[0.76]
3640 VJ3640 0.360 ± 0.015[9.14 ± 0.38]
0.400 ± 0.015[10.20 ± 0.38]
0.120 [3.05]
0.130 (1)
[3.30]0.010[0.25]
0.030[0.76]
4044 VJ4044 0.400 ± 0.015[10.16 ± 0.38]
0.440 ± 0.015[11.17 ± 0.38]
0.120 [3.05]
0.020[0.50]
0.040[1.00]
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE (V)
CAPACITANCE
MINIMUM MAXIMUM
X7R (X5P)
1812 1500 4.7 nF 27 nF
1825 1500 10 nF 56 nF
2225 1500 18 nF 100 nF
3040 1500 33 nF 220 nF
3640 1500 47 nF 330 nF
4044 1500 100 nF 560 nF
ORDERING INFORMATIONVJ3640 Y 184 K X R A T SE
CASECODE
DIELECTRIC CAPACITANCENOMINAL CODE
CAPACITANCETOLERANCE
TERMINATION DC VOLTAGERATING (1)
MARKING PACKAGING (3) PROCESSCODE (2)
181218252225304036404044
Y = X7R Expressed inpicofarads (pF).
The first two digitsare significant,the third is a
multiplier.Examples:
184 = 180 000 pF
J = ± 5 %K = ± 10 %M = ± 20 %
X = Ni barrier100 % tin
matte platedL = Ni barrier with tin lead plated finish
min. 4 % lead
G = 1000 VR = 1500 V
A = unmarked T = 7" reel /plastic tapeJ = 7" reel /plastic tape
(low quantity)
L W
P
TMAX.
Revision: 10-Feb-15 89 Document Number: 45210For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Source Energy Capacitor (SEC)www.vishay.com Vishay Vitramon
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
• Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
SELECTION CHARTDIELECTRIC X7R
STYLE VJ1812 (1) VJ1825 (1) VJ2225 (1) VJ3040 (1) VJ3640 (1) VJ4044 (1)
CASE CODE 1812 1825 2225 3040 3640 4044
VOLTAGE (VDC) 1000 1500 1000 1500 1000 1500 1000 1500 1000 1500 1000 1500
VOLTAGE CODE G R G R G R G R G R G R
CAP. CODE CAP.
332 3.3 nF
392 3.9 nF
472 4.7 nF •
562 5.6 nF •
682 6.8 nF • •
822 8.2 nF • •
103 10 nF • • •
123 12 nF • • •
153 15 nF • • • •
183 18 nF • • • • •
223 22 nF • • • •
273 27 nF • • • • •
333 33 nF • • • • •
393 39 nF • • • • •
473 47 nF • • • • •
563 56 nF • • • • • •
683 68 nF • • • • •
823 82 nF • • • •
104 100 nF • • • • • •
124 120 nF • • • • •
154 150 nF • • • • •
184 180 nF • • • • •
224 220 nF • • • • •
274 270 nF • • • •
334 330 nF • • •
394 390 nF •
474 470 nF •
564 560 nF •
684 680 nF
824 820 nF
105 1000 nF
Revision: 10-Feb-15 90 Document Number: 45210For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Source Energy Capacitor (SEC)www.vishay.com Vishay Vitramon
TYPICAL PARAMETERS
-80
-70
-60
-50
-40
-30
-20
-10
0
10
0 250 500 750 1000 1250 1500
Δ C
AP
AC
ITA
NC
E (%
)
APPLIED VOLTAGE (VDC)
VOLTAGE COEFFICIENT OF CAPACITANCE
3640, 180 nF, 1500 V
4044, 330 nF, 1500 V
-20
-15
-10
-5
0
5
10
15
20
-75 -55 -35 -15 5 25 45 65 85 105 125
ΔΔ C
AP
AC
ITA
NC
E (%
)
TEMPERATURE (°C)
TEMPERATURE COEFFICIENT OF CAPACITANCE
3640, 180 nF, 1500 V
X7R: ± 15 % from -55 °C to 125 °C
TCC also meets X5P± 10 % from
-55 °C to +85 °C
4044, 330 nF, 1500 V
DISCHARGE PULSE OF 330 nF, 4044 SEC
0
500
1000
1500
2000
2500
600 800 1000 1200 1400
PE
AK
DIS
CH
AR
GE
CU
RR
EN
T (
A)
CHARGE VOLTAGE (VDC)
DISCHARGE CURRENT VS. CHARGE VOLTAGE
4044, 330 nF, 1500 V 3040, 120 nF, 1500 V 2225, 100 nF, 1000 V
1825, 56 nF, 1000 V 1812, 27 nF, 1000 V
0.000
0.005
0.010
0.015
0.020
0.025
0.030
0.035
0.040
-55 -35 -15 5 25 45 65 85
DIS
SIP
AT
ION
FA
CT
OR
TEMPERATURE (°C)
DISSIPATION FACTOR VS. TEMPERATURE
3640
4044
0
10
20
30
40
50
60
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
TE
MP
ER
AT
UR
E (°
C)
CURRENT (A)
TEMPERATURE VS. RIPPLE CURRENT
1825, 27 nF, 1000 V tested at 240 kHz1825, 56 nF, 1000 V tested at 120 kHz2225, 100 nF, 1000 V tested at 60 kHz
Revision: 10-Feb-15 91 Document Number: 45210For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Source Energy Capacitor (SEC)www.vishay.com Vishay Vitramon
Notes• Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”• n/a = not available
STANDARD PACKAGING QUANTITIES
CASE CODE TAPE SIZE
7" REEL QUANTITIES
PLASTIC TAPEPACKAGING CODE “T”
LOW QUANTITYPACKAGING CODE “J”
1812 12 mm 1000 500
1825 12 mm 1000 500
2225 12 mm 1000 500
3040 16 mm 500 n/a
3640 16 mm 500 n/a
4044 24 mm 300 n/a
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to 40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 10-Feb-15 92 Document Number: 45210For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Controlled Discharge Capacitor (CDC)www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitorswith Integrated Resistor for High Pulse Current Applications
FEATURES• Integrated resistor on the surface of the
capacitor
• Low electrostrictive ceramic formulation forrepeated charge and discharge cycles
• High pulse discharge currents
• Excellent reliability and high voltage performance
• Available with tin / lead barrier termination (code “L”)
• Wet built process
• Reliable Noble Metal Electrode (NME) system
• Made with a combination of design, materials and tightprocess control to achieve very high field reliability
• Resistor glass overglaze contains lead
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
Note* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information / tables in this datasheet for details.
APPLICATIONS• Detonation devices (munitions, pyrotechnic, blasting)
• Down hole drilling
• Electronic fuzing
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range: 33 nF to 560 nF
Voltage Range: 1000 VDC to 1500 VDC
Temperature Coefficient of Capacitance (TCC): X5P: ± 10 % from -55 °C to +85 °C, with 0 VDC appliedX7R: ± 15 % from -55 °C to +125 °C, with 0 VDC applied
Parallel Resistor: 500 M ± 30 %
Dissipation Factor (DF): 2.5 % maximum at 1.0 VRMS and 1 kHz
Aging Rate: 1 % maximum per decade
Insulation Resistance (IR): at +25 °C without resistor: 100 000 M minimum or 1000 F,whichever is less.at +125 °C without resistor: 10 000 M minimum or 100 F,whichever is less.
Dielectric Strength Test:performed per method 103 of EIA 198-2-E. Applied test voltages: 1000 VDC / 1500 VDC-rated: 120 % of rated voltage
Available
Available
Revision: 10-Feb-15 93 Document Number: 45203For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Controlled Discharge Capacitor (CDC)www.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
Notes(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance
Consult for questions: [email protected](2) Process Code must be added to control special requirements(3) Size designator may be replaced by four digit drawing number used to control non-standard products and / or special requirements
Note(1) Thickness used for 3640 - 1500 V - 220 nF and 270 nF
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE(V)
CAPACITANCE
MINIMUM MAXIMUM
X7R (X5P)
3040 1500 33 nF 220 nF
3640 1500 47 nF 330 nF
4044 1500 100 nF 560 nF
ORDERING INFORMATIONVJ3640 (3) Y 184 K X R A T 8R (2)
CASECODE
DIELECTRIC CAPACITANCENOMINAL CODE
CAPACITANCETOLERANCE
TERMINATION DC VOLTAGERATING (1)
MARKING PACKAGING PROCESSCODE
304036404044
Y = X7R(X5P)
Expressed inpicofarads (pF).
The first two digitsare significant,the third is a
multiplier.Examples:
184 = 180 nF334 = 330 nF
J = ± 5 %K = ± 10 %M = ± 20 %
X = Ni barrier100 % tin plate
matte finishL = Ni barrierwith tin leadplated finish
min. 4 % lead
G = 1000 VR = 1500 V
A = unmarked T = 7" reel / plastic tape
DIMENSIONS in inches [millimeters]
CASE CODEPART
ORDERINGNUMBER
LENGTH(L)
WIDTH(W)
MAXIMUM THICKNESS
(T)
TERMINATION(P)
MINIMUM MAXIMUM
3040 VJ3040 0.300 ± 0.015 [7.62 ± 0.38]
0.400 ± 0.015 [10.20 ± 0.38]
0.100 [2.54]
0.010 [0.25]
0.030[0.76]
3640 VJ3640 0.360 ± 0.015 [9.14 ± 0.38]
0.400 ± 0.015 [10.20 ± 0.38]
0.120 [3.05]
0130 (1)
[3.30]0.010 [0.25]
0.030[0.76]
4044 VJ4044 0.400 ± 0.015 [10.16 ± 0.38]
0.440 ± 0.015 [11.17 ± 0.38]
0.120 [3.05]
0.020 [0.50]
0.040[1.00]
L W
P
TMAX.
Revision: 10-Feb-15 94 Document Number: 45203For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Controlled Discharge Capacitor (CDC)www.vishay.com Vishay Vitramon
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
• Plastic tape(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
CONSTRUCTION
SELECTION CHARTDIELECTRIC X7R (X5P)
STYLE VJ3040 (1) VJ3640 (1) VJ4044 (1)
CASE CODE 3040 3640 4044
VOLTAGE (VDC) 1000 1500 1000 1500 1000 1500
VOLTAGE CODE G R G R G R
CAP. CODE CAP.
223 0.022 μF
273 0.027 μF
333 0.033 μF •
393 0.039 μF •
473 0.047 μF • •
563 0.056 μF • • •
683 0.068 μF • • •
823 0.082 μF • • •
104 0.10 μF • • • • •
124 0.12 μF • • • • •
154 0.15 μF • • • • •
184 0.18 μF • • • • •
224 0.22 μF • • • • •
274 0.27 μF • • • •
334 0.33 μF • • •
394 0.39 μF •
474 0.47 μF •
564 0.56 μF •
684 0.68 μF
824 0.82 μF
105 1.0 μF
125 1.2 μF
155 1.5 μF
185 1.8 μF
225 2.2 μF
275 2.7 μF
335 3.3 μF
Surface mount multilayerceramic chip capacitor
Over glaze: Resistor passivation toprotect against contamination andincrease electrical stability
Resistor: Thick film print
Revision: 10-Feb-15 95 Document Number: 45203For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Controlled Discharge Capacitor (CDC)www.vishay.com Vishay Vitramon
TYPICAL PARAMETERS
10
APPLIED VOLTAGE (VDC)
CA
PA
CIT
AN
CE
(%
)
VOLTAGE COEFFICIENT OF CAPACITANCE
-80
-70
-60
-50
-40
-30
-20
-10
0
0 150012501000750500250
4044, 330 nF, 1500 V
3640, 180 nF, 1500 V
20
TEMPERATURE (°C)
CA
PA
CIT
AN
CE
(%
)
TEMPERATURE COEFFICIENT OF CAPACITANCE
-20
-15
-10
-5
0
5
10
15
-75 1251055-15-35-55 25 45 65 85
4044, 330 nF, 1500 V
3640, 180 nF, 1500 V
X7R: ± 15 % from -55 °C to +125 °C
TCC also meets X5P± 10 % from -55 °C to +85 °C
DISCHARGE PULSE OF 4044 CDC
Peak current:> 1700 Ap
Rise time79 ns
2000
CHARGE VOLTAGE (VDC)
PU
LS
E D
ISC
HA
RG
E C
UR
RE
NT
(A
)DISCHARGE CURRENT VS. CHARGE VOLTAGE
600
800
1000
1200
1400
1600
1800
900 1500120011001000 1300 1400
4044, 330 nF
3640, 274 nF
3640, 180 nF
Above 1200 V, excessive dV/dt may cause failure
0.040
TEMPERATURE (°C)
% D
ISS
IPA
TIO
N F
AC
TO
R
DISSIPATION FACTOR VS. TEMPERATURE
0.000
0.005
0.010
0.020
0.025
0.030
0.035
-55 12525-5-35 8545 65
0.015
105-15
4044, 330 nF, 1500 V
3640, 180 nF, 1500 V
1400
TIME (s)
DIS
CH
AR
GE
VO
LT
AG
E (
VD
C)
SELF DISCHARGE VS. TIME
0
200
600
800
1000
1200
0 900400300100 700500 600
400
800200
Capacitor (no resistor)
CDC, 500 MΩ resistor
Vc = Vo x ε-t/rc
Revision: 10-Feb-15 96 Document Number: 45203For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Controlled Discharge Capacitor (CDC)www.vishay.com Vishay Vitramon
Notes(1) Vishay Vitramon uses embossed plastic carrier tape(2) REFERENCE: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(3) n/a = not available
STANDARD PACKAGING QUANTITIES (1)(2)(3)
CASE CODE TAPE SIZE7" REEL QUANTITIES
PLASTIC TAPE PACKAGING CODE“T”
3040 16 mm 500
3640 16 mm 500
4044 24 mm 300
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to +40 °C ambient temperature and 70 % related humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 10-Feb-15 97 Document Number: 45203For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Safety Certified Capacitors C0G (NP0)www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitorsfor Safety Certified Applications
FEATURES• Approved IEC 60384-14
• Specialty: safety certified capacitors
• Wet build process
• Reliable Noble Metal Electrode (NME) system
• Material categorization:for definitions of compliance please seewww.vishay.com/doc?99912
APPLICATIONS• Power supplies
• Facsimile and telephone
• AC equipment and appliances
• Lighting strike and voltage surge protection
• EMI and AC line filtering
• Isolators
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range X1 / Y2 (1): 10 pF to 1.0 nF
Capacitance Range X2 (1): 10 pF to 470 pF
Voltage Range: 250 VAC
Temperature Coefficient of Capacitance (TCC):0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
Dissipation Factor (DF) (1):0.1 % maximum for values 1000 pF at 1.0 VRMS at 1 MHz or per IEC 60384-14 at 1.0 VRMS at 10 kHz
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 0 % maximum per decade
Voltage Proof Test:X1 / Y2: 1500 VAC (RMS), 60 s ± 1 sX2: 1075 VDC, 60 s ± 1 s
Peak Impulse Voltage:X1 / Y2: 5000 VX2: 2500 V
Climatic Category According to EN 60068-1:55/125/21
Note(1) Test conditions per IEC 60384-14:
Voltage: 1.0 VRMSCapacitance: C 100 pF at 1 MHz and C > 100 pF at 1 kHz
Revision: 09-Sep-14 98 Document Number: 45007For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Safety Certified Capacitors C0G (NP0)www.vishay.com Vishay Vitramon
Notes• Detail ratings see “Selection Chart”• Size 2008 and 2012 are compatible with 1808 and 1812 solderlands and full conform with the IEC-60384-14 requirements for creepage
distance
Notes(1) Process code must be added to control products and requirements• Detail ratings see “Selection Chart”
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE(VAC)
CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0) (X1 / Y2)
2008 250 10 pF 220 pF
2012 250 18 pF 470 pF
2220 250 47 pF 1.0 nF
C0G (NP0) (X2)2008 250 10 pF 390 pF
2012 250 18 pF 470 pF
ORDERING INFORMATIONVJ2008 A 101 K X U S T ### (1)
CASECODE
DIELECTRIC CAPACITANCENOMINAL CODE
CAPACITANCETOLERANCE
TERMINATION AC VOLTAGERATING
MARKING PACKAGING PROCESSCODE
200820122220
A = C0G (NP0) Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is a multiplier.
Examples:101 = 100 pF
J = ± 5 %K = ± 10 %
X = Ni barrier100 % tin plated
U = 250 VAC S = marked(see Part Marking
table below)
X1 = X1 / Y2
X2 = X2
T = 7" reel/plastic tapeR = 11 1/4"/13" reel/plastic tape
PART MARKING
MARKING 1ST DIGITMANUFACTURER
2ND DIGITDIELECTRIC AND RATING
VCV = Vishay
C = C0G/NP0, X1/Y2
VT T = C0G/NP0, X2
DIMENSIONS in inches (millimeters)
CASE CODEPART
ORDERING NUMBER
LENGTH(L)
WIDTH(W)
MAXIMUM THICKNESS
(T)
TERMINATION (P)
MINIMUM MAXIMUM
2008 VJ2008 0.200 ± 0.010(5.08 ± 0.25)
0.080 ± 0.010 (2.03 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
2012 VJ2012 0.200 ± 0.010(5.08 ± 0.25)
0.126 ± 0.008 (3.20 ± 0.20)
0.086(2.18)
0.010(0.25)
0.030(0.76)
2220 VJ22200.220 ± 0.008 (5.59 ± 0.20)
0.200 ± 0.010 (5.08 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
LW
TMAX.
P
Revision: 09-Sep-14 99 Document Number: 45007For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Safety Certified Capacitors C0G (NP0)www.vishay.com Vishay Vitramon
Notes(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
RoHS-compliant
Note(1) Reference: EIA standard RS481 - “Taping of Surface Mount Components for Automatic Placement”
SELECTION CHARTDIELECTRIC C0G (NP0) (X1/Y2) C0G (NP0) (X2)
STYLE VJ2008 (1) VJ2012 (1) VJ2220 (1) VJ2008 (1) VJ2012 (1)
CASE CODE 2008 2012 2220 2008 2012
VOLTAGE (VAC) 250 250 250 250 250
VOLTAGE CODE U U U U U
CAP. CODE CAP.
100 10 pF • •
120 12 pF • •
150 15 pF • •
180 18 pF • • • •
220 22 pF • • • •
270 27 pF • • • •
330 33 pF • • • •
390 39 pF • • • •
470 47 pF • • • • •
560 56 pF • • • • •
680 68 pF • • • • •
820 82 pF • • • • •
101 100 pF • • • • •
121 120 pF • • • • •
151 150 pF • • • • •
181 180 pF • • • • •
221 220 pF • • • • •
271 270 pF • • • •
331 330 pF • • • •
391 390 pF • • • •
471 470 pF • • •
561 560 pF •
681 680 pF •
821 820 pF •
102 1.0 nF •
122 1.2 nF
152 1.5 nF
182 1.8 nF
PACKAGING QUANTITIES (1)
CASE CODE TAPE SIZE7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PACKAGING CODE“T”
PACKAGING CODE “R”
2008 12 mm 2000 10 000
2012 12 mm 1000 4000
2220 12 mm 1000 4000
Revision: 09-Sep-14 100 Document Number: 45007For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Safety Certified Capacitors C0G (NP0)www.vishay.com Vishay Vitramon
APPROVALSIEC 60384-14 - Safety testsCB test certificates:X1/Y2-capacitor: DE1-51726 10 pF to 1000 pF 250 VAC
X2-capacitor: DE1-51726 10 pF to 470 pF 250 VAC
DIN EN 60384-14 (VDE 0565 Teil 1-1):2006-04; EN 60384-14:2005-08; IEC 60384-14 (ed.3)
X1/Y2-capacitor: 70001064 10 pF to 1000 pF 250 V~
X2-capacitor: 70001064 10 pF to 470 pF 250 V~
CAN/CSA-E60384-14:09 and ANSI/UL 60384-14-2009
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to 40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 09-Sep-14 101 Document Number: 45007For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Safety Certified Capacitors X7Rwww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitorsfor Safety Certified Applications
FEATURES• Approved IEC 60384-14
• Specialty: safety certified capacitors
• Wet build process
• Reliable Noble Metal Electrode (NME) system
• Material categorization:for definitions of compliance please seewww.vishay.com/doc?99912
APPLICATIONS• Power supplies
• Facsimile and telephone
• AC equipment and appliances
• Lighting strike and voltage surge protection
• EMI and AC line filtering
• Isolators
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range X1 / Y2 (1): 82 pF to 4.7 nF
Capacitance Range X2 (1): 82 pF to 12 nF
Voltage Range: 250 VAC
Temperature Coefficient of Capacitance (TCC):± 15 % from -55 °C to +125 °C, with 0 VDC applied
Dissipation Factor (DF) (1):2.5 % maximum at 1.0 VRMS at 1 kHzor per IEC 60384-14 at 1.0 VRMS at 10 kHz
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 1 % maximum per decade
Voltage Proof Test:X1 / Y2: 1500 VAC (RMS), 60 s ± 1 sX2: 1075 VDC, 60 s ± 1 s
Peak Impulse Voltage:X1 / Y2: 5000 VX2: 2500 V
Climatic Category According to EN60068-1:55/125/21
Note(1) Test conditions per IEC 60384-14:
Voltage: 1 VRMSCapacitance: C 100 pF at 1 MHz and C > 100 pF at 1 kHz
Revision: 09-Sep-14 102 Document Number: 45020For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Safety Certified Capacitors X7Rwww.vishay.com Vishay Vitramon
Notes• Detail ratings see “Selection Chart”• Size 2008 and 2012 are compatible with 1808 and 1812 solderlands and full conform with the IEC-60384-14 requirements for creepage
distance
Notes(1) Process code must be added to control products and requirements• Detail ratings see “Selection Chart”
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE(VAC)
CAPACITANCE
MINIMUM MAXIMUM
X7R (X1 / Y2)
2008 250 82 pF 1.0 nF
2012 250 150 pF 1.2 nF
2220 250 270 pF 4.7 nF
X7R (X2)
2008 250 82 pF 2.7 nF
2012 250 150 pF 5.6 nF
2220 250 270 pF 12 nF
ORDERING INFORMATIONVJ2008 Y 102 K X U S T ### (1)
CASECODE
DIELECTRIC CAPACITANCENOMINAL CODE
CAPACITANCETOLERANCE
TERMINATION AC VOLTAGERATING
MARKING PACKAGING PROCESSCODE
200820122220
Y = X7R Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is a multiplier.
Examples:102 = 1000 pF
K = ± 10 %M = ± 20 %
X = Ni barrier100 % tin plated
U = 250 VAC S = marked(see Part Marking
table below)
X1 = X1 / Y2
X2 = X2
T = 7" reel / plastic tapeR = 11 1/4" / 13" reel / plastic tape
PART MARKING
MARKING 1ST DIGITMANUFACTURER
2ND DIGITDIELECTRIC AND RATING
VAV = Vishay
A = X7R, X1 / Y2
VM M = X7R, X2
DIMENSIONS in inches (millimeters)
CASE CODEPART
ORDERING NUMBER
LENGTH(L)
WIDTH(W)
MAXIMUM THICKNESS
(T)
TERMINATION (P)
MINIMUM MAXIMUM
2008 VJ2008 0.200 ± 0.010(5.08 ± 0.25)
0.080 ± 0.010 (2.03 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
2012 VJ2012 0.200 ± 0.010(5.08 ± 0.25)
0.126 ± 0.008 (3.20 ± 0.20)
0.086(2.18)
0.010(0.25)
0.030(0.76)
2220 VJ22200.220 ± 0.008 (5.59 ± 0.20)
0.200 ± 0.010 (5.08 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
LW
TMAX.
P
Revision: 09-Sep-14 103 Document Number: 45020For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Safety Certified Capacitors X7Rwww.vishay.com Vishay Vitramon
Notes(1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034
RoHS-compliant
Note(1) Reference: EIA standard RS481 - “Taping of Surface Mount Components for Automatic Placement”
SELECTION CHARTDIELECTRIC X7R (X1 / Y2) X7R (X2)STYLE VJ2008 (1) VJ2012 (1) VJ2220 (1) VJ2008 (1) VJ2012 (1) VJ2220 (1)
CASE CODE 2008 2012 2220 2008 2012 2220VOLTAGE (VAC) 250 250 250 250 250 250VOLTAGE CODE U U U U U UCAP. CODE CAP.
100 10 pF220 22 pF330 33 pF470 47 pF560 56 pF680 68 pF820 82 pF • •101 100 pF • •121 120 pF • •151 150 pF • • • •181 180 pF • • • •221 220 pF • • • •271 270 pF • • • • • •331 330 pF • • • • • •391 390 pF • • • • • •471 470 pF • • • • • •561 560 pF • • • • • •681 680 pF • • • • • •821 820 pF • • • • • •102 1.0 nF • • • • • •122 1.2 nF • • • • •152 1.5 nF • • • •182 1.8 nF • • • •222 2.2 nF • • • •272 2.7 nF • • • •332 3.3 nF • • •392 3.9 nF • • •472 4.7 nF • • •562 5.6 nF • •682 6.8 nF •822 8.2 nF •103 10 nF •123 12 nF •153 15 nF
PACKAGING QUANTITIES (1)
CASE CODE TAPE SIZE7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PACKAGING CODE“T”
PACKAGING CODE “R”
2008 12 mm 2000 10 000
2012 12 mm 1000 4000
2220 12 mm 1000 4000
Revision: 09-Sep-14 104 Document Number: 45020For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Safety Certified Capacitors X7Rwww.vishay.com Vishay Vitramon
APPROVALSIEC 60384-14 - Safety testsCB test certificates:
X1 / Y2-capacitor: DE1-52193 82 pF to 4700 pF 250 VAC
X2-capacitor: DE1-52193 82 pF to 12 000 pF 250 VAC
DIN EN 60384-14 (VDE 0565 Teil 1-1):2006-04; EN 60384-14:2005-08; IEC 60384-14 (ed.3)
X1 / Y2-capacitor: 70001064 82 pF to 4700 pF 250 V~
X2-capacitor: 70001064 82 pF to 12 000 pF 250 V~
CAN/CSA-E60384-14:09 and ANSI/UL 60384-14-2009
STORAGE AND HANDLING CONDITIONS(1) Store the components at 5 °C to 40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 09-Sep-14 105 Document Number: 45020For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Contents
VJ HIFREQ Series .................. 107
QUAD HIFREQ Series............ 117
VJ High Q............................... 130
VJ....W1BC High Q Dielectric 134
VJ....W1BC Ultra High Q /Low ESR ................................ 140MLCCs
for
RF and
High Frequency
Applications
(NME Technology)
VJ HIFREQ Serieswww.vishay.com Vishay Vitramon
Surface Mount MultilayerCeramic Chip Capacitors for High Frequency
FEATURES• Case size 0402, 0603, 0805• High frequency• Ultra-stable dielectric material• Non-magnetic copper termination “C” • Lead (Pb)-free terminations code “X”
• Tin/lead termination code “L” • Surface mount, wet build process• Reliable Noble Metal Electrode (NME) system• Made with a combination of design, materials and tight
process control to achieve very high field reliability• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912 Note* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information / tables in this datasheet for details.
APPLICATIONS• RF and microwave• Broadband communication• Satellite communication• Base stations• Medical instrumentation and test• Military devices (radar, communication, etc.)• Wireless devices
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at 25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range:0402: 0.1 pF to 82 pF0603: 0.1 pF to 470 pF0805: 0.1 pF to 1.5 nF
Voltage Rating: 25 VDC to 250 VDC
Temperature Coefficient of Capacitance (TCC):C0G (D): 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C with
zero (0) VDC applied
Dissipation Factor (DF):C0G (D): 0.05 % max. at 1.0 VRMS and 1 MHz
for values 1000 pFC0G (D): 0.05 % max. at 1.0 VRMS and 1 kHz
for values > 1000 pF
Aging Rate: 0 % maximum per decade
Insulation Resistance (IR): at +25 °C and rated voltage 100 000 M minimum or1000 F, whichever is lessat +125 °C and rated voltage 10 000 M minimum or100 F, whichever is less
Dielectric Strength Test:performed per method 103 of EIA-198-2-E.
Applied test voltages: 200 VDC-rated: min. 250 % of rated voltage> 200 VDC-rated: min. 200 % of rated voltage
Available
Available
Available
Revision: 27-Nov-14 107 Document Number: 45071For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HIFREQ Serieswww.vishay.com Vishay Vitramon
Note• For values below 0.4 pF, contact [email protected]
Notes(1) DC voltage rating should not be exceeded in application(2) Termination code “E” is for conductive epoxy assembly
Note(1) For Cu termination “C” add 0.01 mm to maximum pad terminations
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE(V)
CAPACITANCEMINIMUM MAXIMUM
D = HIFREQ0402 200 0.1 pF 82 pF0603 250 0.1 pF 470 pF0805 250 0.1 pF 1.5 nF
ORDERING INFORMATIONVJ0603 D 1R0 B X B A C
CASECODE
DIELECTRIC CAPACITANCENOMINAL CODE
CAPACITANCETOLERANCE
TERMINATION DC VOLTAGERATING (1)
MARKING PACKAGING
040206030805
D = HIFREQ Expressed inpicofarads (pF).
The first two digitsare significant, the third is a multiplier.An “R” indicates a
decimal point.Examples:
1R0 = 1.0 pF
V = ± 0.05 pFB = ± 0.10 pF C = ± 0.25 pF D = ± 0.50 pF
F = ± 1 %G = ± 2 % J = ± 5 %
K = ± 10 %M = ± 20 %
NoteDetails see“Selection
Chart”
C = non-magneticcopper barrier100 % tin plate
matte finishE = AgPd (2)
X = Ni barrier100 % tin plate
matte finishL = Ni barrierwith tin leadplated finish
min. 4 % lead
X = 25 VA = 50 V
B = 100 VC = 200 VP = 250 V
A = no marking
T = 7" reel/plastic tapeC = 7" reel/paper tape
O = 7" reel/flamed paper tapeJ = 7" reel (low quantity)
R = 11 1/4"/13" reel/plastic tape
P = 11 1/4"/13" reel/paper tape
I = 11 1/4"/13" reel/flamed paper tape
B = bulk
Note“I” and “O” is used for “E”/”N”
termination code
ENVIRONMENTAL STATUSTERMINATION CODE TERMINATION DESCRIPTION RoHS COMPLIANT VISHAY GREEN
C Non-magnetic copper barrier 100 % tin plated matte finish Yes YesX Ni barrier 100 % tin plated matte finish Yes YesE AgPd Yes YesL Ni barrier 100 % tin plated matte finish min. 4 % lead No No
DIMENSIONS in inches (millimeters)
CASECODE STYLE LENGTH
(L)WIDTH
(W)MAXIMUM
THICKNESS (T) TERMINATIONS PAD (P)
MINIMUM MAXIMUM (1)
0402 VJ0402 0.040 ± 0.004(1.02 ± 0.10)
0.020 ± 0.004(0.51 ± 0.10)
0.021(0.61)
0.004(0.10)
0.016(0.41)
0603 VJ0603 0.063 ± 0.006(1.60 ± 0.15)
0.031 ± 0.005(0.80 ± 0.12)
0.037(0.94)
0.012(0.30)
0.018(0.46)
0805 VJ0805 0.079 ± 0.008(2.00 ± 0.20)
0.049 ± 0.008(1.25 ± 0.20)
0.057(1.45)
0.010(0.25)
0.028(0.71)
LW
TMAX.
P
Revision: 27-Nov-14 108 Document Number: 45071For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HIFREQ Serieswww.vishay.com Vishay Vitramon
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)STYLE VJ0402
TOLERANCECASE CODE 0402VOLTAGE (VDC) 25 50 100 200VOLTAGE CODE X A B C
CAP. CODE CAP.0R1 0.1 pF •• •• •• •• V, B, C, D (1)
0R2 0.2 pF •• •• •• •• V, B, C, D (1)
0R3 0.3 pF •• •• •• •• V, B, C, D (1)
0R4 0.4 pF •• •• •• •• V, B, C, D0R5 0.5 pF •• •• •• •• V, B, C, D0R6 0.6 pF •• •• •• •• V, B, C, D0R7 0.7 pF •• •• •• •• V, B, C, D0R8 0.8 pF •• •• •• •• V, B, C, D0R9 0.9 pF •• •• •• •• V, B, C, D1R0 1.0 pF •• •• •• •• V, B, C, D1R1 1.1 pF •• •• •• •• B, C, D1R2 1.2 pF •• •• •• •• B, C, D1R3 1.3 pF •• •• •• •• B, C, D1R4 1.4 pF •• •• •• •• B, C, D1R5 1.5 pF •• •• •• •• B, C, D1R6 1.6 pF •• •• •• •• B, C, D1R7 1.7 pF •• •• •• •• B, C, D1R8 1.8 pF •• •• •• •• B, C, D1R9 1.9 pF •• •• •• •• B, C, D2R0 2.0 pF •• •• •• •• B, C, D2R1 2.1 pF •• •• •• •• B, C, D2R2 2.2 pF •• •• •• •• B, C, D2R4 2.4 pF •• •• •• •• B, C, D2R7 2.7 pF •• •• •• •• B, C, D3R0 3.0 pF •• •• •• •• B, C, D3R3 3.3 pF •• •• •• •• B, C, D3R6 3.6 pF •• •• •• •• B, C, D3R9 3.9 pF •• •• •• •• B, C, D4R3 4.3 pF •• •• •• •• B, C, D4R7 4.7 pF •• •• •• •• B, C, D5R1 5.1 pF •• •• •• •• B, C, D5R6 5.6 pF •• •• •• •• B, C, D6R2 6.2 pF •• •• •• •• B, C, D6R8 6.8 pF •• •• •• •• B, C, D7R5 7.5 pF •• •• •• •• B, C, D8R2 8.2 pF •• •• •• •• B, C, D9R1 9.1 pF •• •• •• •• B, C, D100 10 pF •• •• •• •• F, G, J, K, M110 11 pF •• •• •• •• F, G, J, K, M120 12 pF •• •• •• •• F, G, J, K, M130 13 pF •• •• •• •• F, G, J, K, M150 15 pF •• •• •• •• F, G, J, K, M180 18 pF •• •• •• F, G, J, K, M200 20 pF •• •• •• F, G, J, K, M220 22 pF •• •• •• F, G, J, K, M240 24 pF •• •• •• F, G, J, K, M270 27 pF •• •• •• F, G, J, K, M300 30 pF •• •• F, G, J, K, M330 33 pF •• •• F, G, J, K, M360 36 pF •• •• F, G, J, K, M390 39 pF •• •• F, G, J, K, M430 43 pF •• •• F, G, J, K, M470 47 pF •• •• F, G, J, K, M510 51 pF •• •• F, G, J, K, M560 56 pF •• •• F, G, J, K, M620 62 pF •• F, G, J, K, M680 68 pF •• F, G, J, K, M750 75 pF •• F, G, J, K, M820 82 pF •• F, G, J, K, M910 91 pF101 100 pF111 110 pF121 120 pF
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
•• Paper carrier(1) For values below 0.4 pF and tolerance ± 0.05 pF, contact [email protected]
Revision: 27-Nov-14 109 Document Number: 45071For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HIFREQ Serieswww.vishay.com Vishay Vitramon
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)STYLE VJ0603
TOLERANCECASE CODE 0603VOLTAGE (VDC) 25 50 100 200 250VOLTAGE CODE X A B C PCAP. CODE CAP.
0R1 0.1 pF •• •• •• •• •• V, B, C, D (1)
0R2 0.2 pF •• •• •• •• •• V, B, C, D (1)
0R3 0.3 pF •• •• •• •• •• V, B, C, D (1)
0R4 0.4 pF •• •• •• •• •• V, B, C, D0R5 0.5 pF •• •• •• •• •• V, B, C, D0R6 0.6 pF •• •• •• •• •• V, B, C, D0R7 0.7 pF •• •• •• •• •• V, B, C, D0R8 0.8 pF •• •• •• •• •• V, B, C, D0R9 0.9 pF •• •• •• •• •• V, B, C, D1R0 1.0 pF •• •• •• •• •• B, C, D1R1 1.1 pF •• •• •• •• •• B, C, D1R2 1.2 pF •• •• •• •• •• B, C, D1R3 1.3 pF •• •• •• •• •• B, C, D1R4 1.4 pF •• •• •• •• •• B, C, D1R5 1.5 pF •• •• •• •• •• B, C, D1R6 1.6 pF •• •• •• •• •• B, C, D1R7 1.7 pF •• •• •• •• •• B, C, D1R8 1.8 pF •• •• •• •• •• B, C, D1R9 1.9 pF •• •• •• •• •• B, C, D2R0 2.0 pF •• •• •• •• •• B, C, D2R1 2.1 pF •• •• •• •• •• B, C, D2R2 2.2 pF •• •• •• •• •• B, C, D2R4 2.4 pF •• •• •• •• •• B, C, D2R7 2.7 pF •• •• •• •• •• B, C, D3R0 3.0 pF •• •• •• •• •• B, C, D3R3 3.3 pF •• •• •• •• •• B, C, D3R6 3.6 pF •• •• •• •• •• B, C, D3R9 3.9 pF •• •• •• •• •• B, C, D4R3 4.3 pF •• •• •• •• •• B, C, D4R7 4.7 pF •• •• •• •• •• B, C, D5R1 5.1 pF •• •• •• •• •• B, C, D5R6 5.6 pF •• •• •• •• •• B, C, D6R2 6.2 pF •• •• •• •• •• B, C, D6R8 6.8 pF •• •• •• •• •• B, C, D7R5 7.5 pF •• •• •• •• •• B, C, D8R2 8.2 pF •• •• •• •• •• B, C, D9R1 9.1 pF •• •• •• •• •• B, C, D100 10 pF •• •• •• •• •• F, G, J, K, M110 11 pF •• •• •• •• •• F, G, J, K, M120 12 pF •• •• •• •• •• F, G, J, K, M130 13 pF •• •• •• •• •• F, G, J, K, M150 15 pF •• •• •• •• •• F, G, J, K, M180 18 pF •• •• •• •• •• F, G, J, K, M200 20 pF •• •• •• •• •• F, G, J, K, M220 22 pF •• •• •• •• •• F, G, J, K, M240 24 pF •• •• •• •• •• F, G, J, K, M270 27 pF •• •• •• •• •• F, G, J, K, M300 30 pF •• •• •• •• •• F, G, J, K, M330 33 pF •• •• •• •• •• F, G, J, K, M360 36 pF •• •• •• •• •• F, G, J, K, M390 39 pF •• •• •• •• •• F, G, J, K, M430 43 pF •• •• •• •• •• F, G, J, K, M470 47 pF •• •• •• •• •• F, G, J, K, M510 51 pF •• •• •• •• •• F, G, J, K, M560 56 pF •• •• •• •• •• F, G, J, K, M620 62 pF • • • • • F, G, J, K, M680 68 pF • • • • • F, G, J, K, M750 75 pF • • • • • F, G, J, K, M820 82 pF • • • • • F, G, J, K, M910 91 pF • • • • • F, G, J, K, M
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
•• Paper carrier • Plastic carrier tape(1) For values below 0.4 pF and tolerance ± 0.05 pF, contact [email protected]
Revision: 27-Nov-14 110 Document Number: 45071For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HIFREQ Serieswww.vishay.com Vishay Vitramon
101 100 pF • • • • • F, G, J, K, M
111 110 pF • • • F, G, J, K, M
121 120 pF • • • F, G, J, K, M
131 130 pF • • • F, G, J, K, M
151 150 pF • • • F, G, J, K, M
181 180 pF • • F, G, J, K, M
201 200 pF • • F, G, J, K, M
221 220 pF • • F, G, J, K, M
241 240 pF • • F, G, J, K, M
271 270 pF • • F, G, J, K, M
301 300 pF • • F, G, J, K, M
331 330 pF • • F, G, J, K, M
361 360 pF • F, G, J, K, M
391 390 pF • F, G, J, K, M
431 430 pF • F, G, J, K, M
471 470 pF • F, G, J, K, M
511 510 pF
561 560 pF
621 620 pF
681 680 pF
751 750 pF
821 820 pF
911 910 pF
102 1.0 nF
112 1.1 nF
122 1.2 nF
132 1.3 nF
152 1.5 nF
182 1.8 nF
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)STYLE VJ0603
TOLERANCECASE CODE 0603VOLTAGE (VDC) 25 50 100 200 250VOLTAGE CODE X A B C PCAP. CODE CAP.
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
•• Paper carrier • Plastic carrier tape(1) For values below 0.4 pF and tolerance ± 0.05 pF, contact [email protected]
Revision: 27-Nov-14 111 Document Number: 45071For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HIFREQ Serieswww.vishay.com Vishay Vitramon
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)
STYLE VJ0805
TOLERANCE
CASE CODE 0805
VOLTAGE (VDC) 25 50 100 200 250
VOLTAGE CODE X A B C P
CAP. CODE CAP.
0R1 0.1 pF •• •• •• •• •• V, B, C, D (1)
0R2 0.2 pF •• •• •• •• •• V, B, C, D (1)
0R3 0.3 pF •• •• •• •• •• V, B, C, D (1)
0R4 0.4 pF •• •• •• •• •• V, B, C, D
0R5 0.5 pF •• •• •• •• •• V, B, C, D
0R6 0.6 pF •• •• •• •• •• V, B, C, D
0R7 0.7 pF •• •• •• •• •• V, B, C, D
0R8 0.8 pF •• •• •• •• •• V, B, C, D
0R9 0.9 pF •• •• •• •• •• V, B, C, D
1R0 1.0 pF •• •• •• •• •• B, C, D
1R1 1.1 pF •• •• •• •• •• B, C, D
1R2 1.2 pF •• •• •• •• •• B, C, D
1R3 1.3 pF •• •• •• •• •• B, C, D
1R4 1.4 pF •• •• •• •• •• B, C, D
1R5 1.5 pF •• •• •• •• •• B, C, D
1R6 1.6 pF •• •• •• •• •• B, C, D
1R7 1.7 pF •• •• •• •• •• B, C, D
1R8 1.8 pF •• •• •• •• •• B, C, D
1R9 1.9 pF •• •• •• •• •• B, C, D
2R0 2.0 pF •• •• •• •• •• B, C, D
2R1 2.1 pF •• •• •• •• •• B, C, D
2R2 2.2 pF •• •• •• •• •• B, C, D
2R4 2.4 pF •• •• •• •• •• B, C, D
2R7 2.7 pF •• •• •• •• •• B, C, D
3R0 3.0 pF •• •• •• •• •• B, C, D
3R3 3.3 pF •• •• •• •• •• B, C, D
3R6 3.6 pF •• •• •• •• •• B, C, D
3R9 3.9 pF •• •• •• •• •• B, C, D
4R3 4.3 pF •• •• •• •• •• B, C, D
4R7 4.7 pF •• •• •• •• •• B, C, D
5R1 5.1 pF •• •• •• •• •• B, C, D
5R6 5.6 pF •• •• •• •• •• B, C, D
6R2 6.2 pF •• •• •• •• •• B, C, D
6R8 6.8 pF •• •• •• •• •• B, C, D
7R5 7.5 pF •• •• •• •• •• B, C, D
8R2 8.2 pF •• •• •• •• •• B, C, D
9R1 9.1 pF •• •• •• •• •• B, C, D
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
•• Paper carrier • Plastic carrier tape(1) For values below 0.4 pF and tolerance ± 0.05 pF, contact [email protected]
Revision: 27-Nov-14 112 Document Number: 45071For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HIFREQ Serieswww.vishay.com Vishay Vitramon
100 10 pF •• •• •• •• •• F, G, J, K, M110 11 pF •• •• •• •• •• F, G, J, K, M120 12 pF •• •• •• •• •• F, G, J, K, M130 13 pF •• •• •• •• •• F, G, J, K, M150 15 pF •• •• •• •• •• F, G, J, K, M180 18 pF •• •• •• •• •• F, G, J, K, M200 20 pF •• •• •• •• •• F, G, J, K, M220 22 pF •• •• •• •• •• F, G, J, K, M240 24 pF •• •• •• •• •• F, G, J, K, M270 27 pF •• •• •• •• •• F, G, J, K, M300 30 pF •• •• •• •• •• F, G, J, K, M330 33 pF •• •• •• •• •• F, G, J, K, M360 36 pF •• •• •• •• •• F, G, J, K, M390 39 pF •• •• •• •• •• F, G, J, K, M430 43 pF •• •• •• •• •• F, G, J, K, M470 47 pF •• •• •• •• •• F, G, J, K, M510 51 pF •• •• •• •• •• F, G, J, K, M560 56 pF •• •• •• •• •• F, G, J, K, M620 62 pF •• •• •• •• •• F, G, J, K, M680 68 pF •• •• •• •• •• F, G, J, K, M750 75 pF •• •• •• •• •• F, G, J, K, M820 82 pF •• •• •• •• •• F, G, J, K, M910 91 pF •• •• •• •• •• F, G, J, K, M101 100 pF • • • • • F, G, J, K, M111 110 pF • • • • • F, G, J, K, M121 120 pF • • • • • F, G, J, K, M131 130 pF • • • • • F, G, J, K, M151 150 pF • • • • • F, G, J, K, M181 180 pF • • • • • F, G, J, K, M201 200 pF • • • • • F, G, J, K, M221 220 pF • • • • • F, G, J, K, M241 240 pF • • • • • F, G, J, K, M271 270 pF • • • • • F, G, J, K, M301 300 pF • • • • • F, G, J, K, M331 330 pF • • • • • F, G, J, K, M361 360 pF • • • • F, G, J, K, M391 390 pF • • • • F, G, J, K, M431 430 pF • • • F, G, J, K, M471 470 pF • • • F, G, J, K, M511 510 pF • • • F, G, J, K, M561 560 pF • • • F, G, J, K, M621 620 pF • • • F, G, J, K, M681 680 pF • • • F, G, J, K, M751 750 pF • • F, G, J, K, M821 820 pF • • F, G, J, K, M911 910 pF • • F, G, J, K, M102 1.0 nF • • F, G, J, K, M112 1.1 nF • F, G, J, K, M122 1.2 nF • F, G, J, K, M132 1.3 nF • F, G, J, K, M152 1.5 nF • F, G, J, K, M182 1.8 nF
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)
STYLE VJ0805
TOLERANCE
CASE CODE 0805
VOLTAGE (VDC) 25 50 100 200 250
VOLTAGE CODE X A B C P
CAP. CODE CAP.
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
•• Paper carrier • Plastic carrier tape(1) For values below 0.4 pF and tolerance ± 0.05 pF, contact [email protected]
Revision: 27-Nov-14 113 Document Number: 45071For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HIFREQ Serieswww.vishay.com Vishay Vitramon
HIGH FREQ DIELECTRIC - TYPICAL PARAMETERS
- 75 - 50 - 25 0 50 100 125
2.0
1.5
1.0
0.5
0.0
- 0.5
- 1.0
- 1.5
- 2.0
NP0
TEMPERATURE °C
150 175 25 75
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE COEFFICIENT OF CAPACITANCE
TEMPERATURE °C
MIN. INSULATION RESISTANCE VS. TEMPERATURE
10 25 100 150
10 000
1000
100
1050
INS
UL
AT
ION
RE
SIS
TAN
CE
(ΩF
)
AGING RATE
HOURS
100 1000 10 000
% C
APA
CIT
AN
CE
CH
AN
GE
0.2
0.1
0.0
- 0.1
- 0.21 10
0.2
0.1
0.0
- 0.1
- 0.2
DC VOLTS APPLIED
VOLTAGE COEFFICIENT OF CAPACITANCE
% C
APA
CIT
AN
CE
CH
AN
GE
0 10 20 30 40 50 60 70 80 90 100
1
10
100
1000
10 000
100 1000
Q
FREQUENCY (MHz)
TYPICAL Q VALUE VS. FREQUENCY SIZE 0402
1 pF
15 pF
27 pF82 pF
0.01
0.1
1
100 1000
ES
R (Ω
)
FREQUENCY (MHz)
TYPICAL ESR VS. FREQUENCY SIZE 0402
1 pF
15 pF27 pF82 pF
1
10
100
1 10 100
SR
F/P
RF
(GH
z)
CAPACITANCE (pF)
TYPICAL SRF/PRF VS. CAPACITANCESIZE 0402
PRF
SRF
Revision: 27-Nov-14 114 Document Number: 45071For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HIFREQ Serieswww.vishay.com Vishay Vitramon
HIGH FREQ DIELECTRIC - TYPICAL PARAMETERS
1
10
100
1000
10 000
100 1000
Q
FREQUENCY (MHz)
TYPICAL Q VALUE VS. FREQUENCY SIZE 0603
1 pF
4.7 pF
470 pF
100 pF
0.01
0.1
1
100 1000
ES
R (Ω
)
FREQUENCY (MHz)
TYPICAL ESR VS. FREQUENCY SIZE 0603
1 pF
4.7 pF
470 pF
100 pF
0.1
1
10
100
1 10 100 1000
SR
F/P
RF
(GH
z)
CAPACITANCE (pF)
PRF SRF
TYPICAL SRF/PRF VS. CAPACITANCESIZE 0603
1
10
100
1000
10 000
100 1000
Q
FREQUENCY (MHz)
TYPICAL Q VALUE VS. FREQUENCY SIZE 0805
1 pF
680 pF
330 pF
0.01
0.1
1
100 1000
ES
R (Ω
)
FREQUENCY (MHz)
TYPICAL ESR VS. FREQUENCY SIZE 0805
1 pF
680 pF
330 pF
0.1
1
10
100
1 10 100 1000 10 000
SR
F/P
RF
(GH
z)
CAPACITANCE (pF)
PRF SRF
TYPICAL SRF/PRF VS. CAPACITANCESIZE 0805
Revision: 27-Nov-14 115 Document Number: 45071For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ HIFREQ Serieswww.vishay.com Vishay Vitramon
Notes(1) Vishay Vitramon uses embossed plastic carrier tape(2) REFERENCE: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(3) n/a = not available(4) Packaging “C”/”P”/”O”/”I” and “T”/”R” or lower quantities can depend from product thickness(5) Paper/plastic tape used by availability
STANDARD PACKAGING QUANTITIES (1)(2)(3)
CASECODE
TAPESIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PAPER TAPEPACKAGING CODE
“C”/“O”
PLASTIC TAPEPACKAGING CODE
“T”
LOWQUANTITY
“J” (5)
PAPER TAPEPACKAGING CODE
“P”/“I”
PLASTIC TAPEPACKAGING CODE
“R”
0402 8 mm 5000 n/a 1000 10 000 n/a
0603 (4) 8 mm 4000 4000 1000 10 000 10 000
0805 (4) 8 mm 3000 3000 1000 10 000 10 000
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to +40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment (1 year for copper).
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 27-Nov-14 116 Document Number: 45071For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Capacitorsfor RF Power Applications
FEATURES• Case size 0505, 1111, 2525, and 3838
• Ultra-stable, high Q dielectric material
• Lead (Pb)-free terminations code “X”
• Tin/lead termination code “L”
• Non-magnetic copper termination code “C”
• Reliable Noble Metal Electrode (NME) system
• High frequency
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
Note* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information / tables in this datasheet for details.
APPLICATIONS
• MRI coils and generators
• RF instruments
• Lasers, CATV, UHF/microwave RF power amplifiers
• Filter networks, timing circuits
• Mixers, oscillators impedance matching networks
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at 25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range:0505: 0.1 pF to 100 pF1111: 0.2 pF to 1000 pF2525: 1.0 pF to 2700 pF3838: 1.0 pF to 5100 pF
Voltage Rating:0505: 200 VDC to 250 VDC1111: 300 VDC to 1500 VDC2525: 300 VDC to 3600 VDC3838: 500 VDC to 7200 VDC
Temperature Coefficient of Capacitance (TCC):C0G (D): 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C with
zero (0) VDC applied
Dissipation Factor (DF):C0G (D): 0.05 % max. at 1.0 VRMS and 1 MHz
for values 1000 pF
C0G (D): 0.05 % max. at 1.0 VRMS and 1 kHzfor values > 1000 pF
Aging Rate: 0 % maximum per decade
Insulation Resistance (IR):at +25 °C and rated voltage 100 000 M minimum or1000 F, whichever is lessat +125 °C and rated voltage 10 000 M minimum or100 F, whichever is less
Dielectric Strength Test:performed per method 103 of EIA-198-2-E.
Applied test voltages: 250 VDC-rated: min. 250 % of rated voltage300 VDC-rated: min. 150 % of rated voltage630 VDC- to 1000 VDC-rated: 150 % of rated voltage1500 VDC and up: 120 % rated voltage
Available
Available
Available
Revision: 23-Jan-15 117 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
Notes• For values below 0.4 pF and tolerance ± 0.05 pF, contact [email protected]
Detail ratings see “Selection Chart”
Note(1) DC voltage rating should not be exceeded in application
Note(1) For copper terminations add 0.01 mm to maximum termination pad
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE(V)
CAPACITANCEMINIMUM MAXIMUM
D = NP0
0505 250 0.1 pF 100 pF1111 1500 0.2 pF 1000 pF2525 3600 1.0 pF 2700 pF3838 7200 1.0 pF 5100 pF
ORDERING INFORMATIONVJ0505 D 1R0 B X C A C
CASECODE
DIELECTRIC CAPACITANCENOMINAL CODE
CAPACITANCETOLERANCE
TERMINATION DC VOLTAGERATING (1)
MARKING PACKAGING
0505111125253838
D = HIFREQ Expressed inpicofarads (pF).
The first two digitsare significant, the third is a multiplier.An “R” indicates a
decimal point.Examples:
1R0 = 1.0 pF
V = ± 0.05 pFB = ± 0.10 pF C = ± 0.25 pF D = ± 0.50 pF
F = ± 1 %G = ± 2 % J = ± 5 %
K = ± 10 %M = ± 20 %
NoteDetails see“Selection
Chart”
C = non-magnetic copper barrier100 % tin plate
matte finishX = Ni barrier
100 % tin platematte finish
L = Ni barrierwith tin leadplated finish
min. 4 % lead
C = 200 VP = 250 VD = 300 VE = 500 VL = 630 VI = 800 V
G = 1000 VR = 1500 VF = 2000 VO = 2500 VH = 3000 VW = 3600 VS = 7200 V
A = no marking
M = marking
T = 7" reel/plastic tapeJ = 7" reel (low quantity)
R = 11 1/4"/13" reel/plastic tape
W = waffle pack
ENVIRONMENTAL STATUSTERMINATION CODE TERMINATION DESCRIPTION RoHS COMPLIANT VISHAY GREEN
X Ni barrier 100 % tin plated matte finish Yes YesL Ni barrier with tin lead plated finish min. 4 % lead No NoC Cu barrier 100 % tin plated matte finish (non-magnetic) Yes Yes
DIMENSIONS in inches (millimeters)
CASECODE STYLE LENGTH
(L)WIDTH
(W)MAXIMUM
THICKNESS (T) TERMINATIONS PAD (P)
MINIMUM MAXIMUM (1)
0505 VJ0505 0.055 ± 0.025(1.40 ± 0.64)
0.055 ± 0.015(1.40 ± 0.38)
0.057(1.45)
0.004(0.10)
0.016(0.41)
1111 VJ1111 0.117 ± 0.028(2.98 ± 0.70)
0.110 ± 0.030(2.79 ± 0.76)
0.102(2.59)
0.012(0.30)
0.018(0.46)
2525 VJ2525 0.250 + 0.020/- 0.030(6.35 + 0.508/- 0.762)
0.250 ± 0.015(6.35 ± 0.381)
0.102(2.59)
0.010(0.25)
0.030(0.76)
3838 VJ3838 0.360 - 0.400(9.14 - 10.15)
0.360 - 0.400(9.14 - 10.15)
0.118(3.00)
0.010(0.25)
0.030(0.76)
LW
TMAX.
P
Revision: 23-Jan-15 118 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)STYLE VJ0505
TOLERANCECASE CODE 0505VOLTAGE (VDC) 200 250VOLTAGE CODE C P
CAP. CODE CAP.0R1 0.1 pF • • B, C, D (1)
0R2 0.2 pF • • B, C, D (1)
0R3 0.3 pF • • B, C, D (1)
0R4 0.4 pF • • V, B, C, D0R5 0.5 pF • • V, B, C, D0R6 0.6 pF • • V, B, C, D0R7 0.7 pF • • V, B, C, D0R8 0.8 pF • • V, B, C, D0R9 0.9 pF • • V, B, C, D1R0 1.0 pF • • V, B, C, D1R1 1.1 pF • • V, B, C, D1R2 1.2 pF • • V, B, C, D1R3 1.3 pF • • V, B, C, D1R4 1.4 pF • • V, B, C, D1R5 1.5 pF • • V, B, C, D1R6 1.6 pF • • V, B, C, D1R7 1.7 pF • • V, B, C, D1R8 1.8 pF • • V, B, C, D1R9 1.9 pF • • V, B, C, D2R0 2.0 pF • • V, B, C, D2R1 2.1 pF • • V, B, C, D2R2 2.2 pF • • V, B, C, D2R4 2.4 pF • • V, B, C, D2R7 2.7 pF • • V, B, C, D3R0 3.0 pF • • V, B, C, D3R3 3.3 pF • • V, B, C, D3R6 3.6 pF • • V, B, C, D3R9 3.9 pF • • V, B, C, D4R3 4.3 pF • • V, B, C, D4R7 4.7 pF • • V, B, C, D5R1 5.1 pF • • B, C, D5R6 5.6 pF • • B, C, D6R2 6.2 pF • • B, C, D6R8 6.8 pF • • B, C, D7R5 7.5 pF • • B, C, D8R2 8.2 pF • • B, C, D9R1 9.1 pF • • B, C, D100 10 pF • • F, G, J, K, M110 11 pF • • F, G, J, K, M120 12 pF • • F, G, J, K, M130 13 pF • • F, G, J, K, M150 15 pF • • F, G, J, K, M180 18 pF • • F, G, J, K, M200 20 pF • • F, G, J, K, M220 22 pF • • F, G, J, K, M240 24 pF • • F, G, J, K, M270 27 pF • • F, G, J, K, M300 30 pF • • F, G, J, K, M330 33 pF • • F, G, J, K, M360 36 pF • • F, G, J, K, M390 39 pF • • F, G, J, K, M430 43 pF • • F, G, J, K, M470 47 pF • • F, G, J, K, M510 51 pF • • F, G, J, K, M560 56 pF • • F, G, J, K, M620 62 pF • F, G, J, K, M680 68 pF • F, G, J, K, M750 75 pF • F, G, J, K, M820 82 pF • F, G, J, K, M910 91 pF • F, G, J, K, M101 100 pF • F, G, J, K, M
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
• Plastic carrier tape(1) For values below 0.4 pF and tolerance ± 0.05 pF contact [email protected]
Revision: 23-Jan-15 119 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)STYLE VJ1111
TOLERANCECASE CODE 1111VOLTAGE (VDC) 300 630 1000 1500VOLTAGE CODE D L G R
CAP. CODE CAP.0R2 0.2 pF • • • • B, C, D (1)
0R3 0.3 pF • • • • B, C, D (1)
0R4 0.4 pF • • • • V, B, C, D0R5 0.5 pF • • • • V, B, C, D0R6 0.6 pF • • • • V, B, C, D0R7 0.7 pF • • • • V, B, C, D0R8 0.8 pF • • • • V, B, C, D0R9 0.9 pF • • • • V, B, C, D1R0 1.0 pF • • • • V, B, C, D1R1 1.1 pF • • • • V, B, C, D1R2 1.2 pF • • • • V, B, C, D1R3 1.3 pF • • • • V, B, C, D1R4 1.4 pF • • • • V, B, C, D1R5 1.5 pF • • • • V, B, C, D1R6 1.6 pF • • • • V, B, C, D1R7 1.7 pF • • • • V, B, C, D1R8 1.8 pF • • • • V, B, C, D1R9 1.9 pF • • • • V, B, C, D2R0 2.0 pF • • • • V, B, C, D2R1 2.1 pF • • • • V, B, C, D2R2 2.2 pF • • • • V, B, C, D2R4 2.4 pF • • • • V, B, C, D2R7 2.7 pF • • • • V, B, C, D3R0 3.0 pF • • • • V, B, C, D3R3 3.3 pF • • • • V, B, C, D3R6 3.6 pF • • • • V, B, C, D3R9 3.9 pF • • • • V, B, C, D4R3 4.3 pF • • • • V, B, C, D4R7 4.7 pF • • • • V, B, C, D5R1 5.1 pF • • • • V, B, C, D5R6 5.6 pF • • • • B, C, D6R2 6.2 pF • • • • B, C, D6R8 6.8 pF • • • • B, C, D7R5 7.5 pF • • • • B, C, D8R2 8.2 pF • • • • B, C, D9R1 9.1 pF • • • • B, C, D100 10 pF • • • • F, G, J, K, M110 11 pF • • • • F, G, J, K, M120 12 pF • • • • F, G, J, K, M130 13 pF • • • • F, G, J, K, M150 15 pF • • • • F, G, J, K, M180 18 pF • • • • F, G, J, K, M200 20 pF • • • • F, G, J, K, M220 22 pF • • • • F, G, J, K, M240 24 pF • • • • F, G, J, K, M270 27 pF • • • • F, G, J, K, M300 30 pF • • • • F, G, J, K, M330 33 pF • • • • F, G, J, K, M360 36 pF • • • • F, G, J, K, M390 39 pF • • • • F, G, J, K, M430 43 pF • • • • F, G, J, K, M470 47 pF • • • • F, G, J, K, M510 51 pF • • • • F, G, J, K, M560 56 pF • • • • F, G, J, K, M620 62 pF • • • • F, G, J, K, M680 68 pF • • • • F, G, J, K, M750 75 pF • • • • F, G, J, K, M820 82 pF • • • • F, G, J, K, M910 91 pF • • • • F, G, J, K, M
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
• Plastic carrier tape(1) For values below 0.4 pF and tolerance ± 0.05 pF contact [email protected]
Revision: 23-Jan-15 120 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
101 100 pF • • • • F, G, J, K, M
111 110 pF • • • • F, G, J, K, M
121 120 pF • • • F, G, J, K, M
131 130 pF • • • F, G, J, K, M
151 150 pF • • • F, G, J, K, M
181 180 pF • • • F, G, J, K, M
201 200 pF • • F, G, J, K, M
221 220 pF • • F, G, J, K, M
241 240 pF • • F, G, J, K, M
301 300 pF • • F, G, J, K, M
331 330 pF • • F, G, J, K, M
361 360 pF • • F, G, J, K, M
391 390 pF • • F, G, J, K, M
431 430 pF • • F, G, J, K, M
471 470 pF • • F, G, J, K, M
511 510 pF • F, G, J, K, M
561 560 pF • F, G, J, K, M
621 620 pF • F, G, J, K, M
681 680 pF • F, G, J, K, M
751 750 pF • F, G, J, K, M
821 820 pF • F, G, J, K, M
911 910 pF • F, G, J, K, M
102 1.0 nF • F, G, J, K, M
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)STYLE VJ1111
TOLERANCECASE CODE 1111VOLTAGE (VDC) 300 630 1000 1500VOLTAGE CODE D L G R
CAP. CODE CAP.
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
• Plastic carrier tape(1) For values below 0.4 pF and tolerance ± 0.05 pF contact [email protected]
Revision: 23-Jan-15 121 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)STYLE VJ2525
TOLERANCECASE CODE 2525VOLTAGE (VDC) 300 500 800 1000 1500 2000 2500 3000 3600VOLTAGE CODE D E I G R F O H WCAP. CODE CAP.
1R0 1.0 pF • • • • • • • • • B, C, D1R1 1.1 pF • • • • • • • • • B, C, D1R2 1.2 pF • • • • • • • • • B, C, D1R3 1.3 pF • • • • • • • • • B, C, D1R4 1.4 pF • • • • • • • • • B, C, D1R5 1.5 pF • • • • • • • • • B, C, D1R6 1.6 pF • • • • • • • • • B, C, D1R7 1.7 pF • • • • • • • • • B, C, D1R8 1.8 pF • • • • • • • • • B, C, D1R9 1.9 pF • • • • • • • • • B, C, D2R0 2.0 pF • • • • • • • • • B, C, D2R1 2.1 pF • • • • • • • • • B, C, D2R2 2.2 pF • • • • • • • • • B, C, D2R4 2.4 pF • • • • • • • • • B, C, D2R7 2.7 pF • • • • • • • • • B, C, D3R0 3.0 pF • • • • • • • • • B, C, D3R3 3.3 pF • • • • • • • • • B, C, D3R6 3.6 pF • • • • • • • • • B, C, D3R9 3.9 pF • • • • • • • • • B, C, D4R3 4.3 pF • • • • • • • • • B, C, D4R7 4.7 pF • • • • • • • • • B, C, D5R1 5.1 pF • • • • • • • • • B, C, D5R6 5.6 pF • • • • • • • • • B, C, D6R2 6.2 pF • • • • • • • • • B, C, D6R8 6.8 pF • • • • • • • • • B, C, D7R5 7.5 pF • • • • • • • • • B, C, D8R2 8.2 pF • • • • • • • • • B, C, D9R1 9.1 pF • • • • • • • • • B, C, D100 10 pF • • • • • • • • • F, G, J, K, M110 11 pF • • • • • • • • • F, G, J, K, M120 12 pF • • • • • • • • • F, G, J, K, M130 13 pF • • • • • • • • • F, G, J, K, M150 15 pF • • • • • • • • • F, G, J, K, M160 16 pF • • • • • • • • • F, G, J, K, M180 18 pF • • • • • • • • • F, G, J, K, M200 20 pF • • • • • • • • • F, G, J, K, M220 22 pF • • • • • • • • • F, G, J, K, M240 24 pF • • • • • • • • • F, G, J, K, M270 27 pF • • • • • • • • • F, G, J, K, M300 30 pF • • • • • • • • • F, G, J, K, M330 33 pF • • • • • • • • • F, G, J, K, M360 36 pF • • • • • • • • • F, G, J, K, M390 39 pF • • • • • • • • • F, G, J, K, M430 43 pF • • • • • • • • • F, G, J, K, M470 47 pF • • • • • • • • • F, G, J, K, M510 51 pF • • • • • • • • • F, G, J, K, M560 56 pF • • • • • • • • • F, G, J, K, M620 62 pF • • • • • • • • • F, G, J, K, M680 68 pF • • • • • • • • • F, G, J, K, M750 75 pF • • • • • • • • • F, G, J, K, M820 82 pF • • • • • • • • • F, G, J, K, M910 91 pF • • • • • • • • • F, G, J, K, M
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
• Plastic carrier tape- For tolerance B contact [email protected]
Revision: 23-Jan-15 122 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
101 100 pF • • • • • • • • • F, G, J, K, M
111 110 pF • • • • • • • • F, G, J, K, M
121 120 pF • • • • • • • • F, G, J, K, M
131 130 pF • • • • • • • • F, G, J, K, M
151 150 pF • • • • • • • • F, G, J, K, M
161 160 pF • • • • • • • • F, G, J, K, M
181 180 pF • • • • • • • • F, G, J, K, M
201 200 pF • • • • • • • • F, G, J, K, M
221 220 pF • • • • • • • • F, G, J, K, M
241 240 pF • • • • • • • • F, G, J, K, M
271 270 pF • • • • • • • • F, G, J, K, M
301 300 pF • • • • • • F, G, J, K, M
331 330 pF • • • • • • F, G, J, K, M
361 360 pF • • • • • • F, G, J, K, M
391 390 pF • • • • • • F, G, J, K, M
431 430 pF • • • • • • F, G, J, K, M
471 470 pF • • • • • • F, G, J, K, M
511 510 pF • • • • • F, G, J, K, M
561 560 pF • • • • • F, G, J, K, M
621 620 pF • • • • • F, G, J, K, M
681 680 pF • • • • • F, G, J, K, M
751 750 pF • • • • • F, G, J, K, M
821 820 pF • • • • • F, G, J, K, M
911 910 pF • • • • • F, G, J, K, M
102 1.0 nF • • • • • F, G, J, K, M
112 1.1 nF • • • • • F, G, J, K, M
122 1.2 nF • • • • • F, G, J, K, M
152 1.5 nF • • • F, G, J, K, M
182 1.8 nF • • • F, G, J, K, M
222 2.0 nF • • • F, G, J, K, M
242 2.4 nF • F, G, J, K, M
272 2.7 nF • F, G, J, K, M
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)STYLE VJ2525
TOLERANCECASE CODE 2525VOLTAGE (VDC) 300 500 800 1000 1500 2000 2500 3000 3600VOLTAGE CODE D E I G R F O H WCAP. CODE CAP.
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
• Plastic carrier tape- For tolerance B contact [email protected]
Revision: 23-Jan-15 123 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)STYLE VJ3838
TOLERANCECASE CODE 3838VOLTAGE (VDC) 500 1000 2500 3600 5000 7200VOLTAGE CODE E G O W M S
CAP. CODE CAP.1R0 1.0 pF • • • • • • B, C, D1R1 1.1 pF • • • • • • B, C, D1R2 1.2 pF • • • • • • B, C, D1R3 1.3 pF • • • • • • B, C, D1R4 1.4 pF • • • • • • B, C, D1R5 1.5 pF • • • • • • B, C, D1R6 1.6 pF • • • • • • B, C, D1R7 1.7 pF • • • • • • B, C, D1R8 1.8 pF • • • • • • B, C, D1R9 1.9 pF • • • • • • B, C, D2R0 2.0 pF • • • • • • B, C, D2R1 2.1 pF • • • • • • B, C, D2R2 2.2 pF • • • • • • B, C, D2R4 2.4 pF • • • • • • B, C, D2R7 2.7 pF • • • • • • B, C, D3R0 3.0 pF • • • • • • B, C, D3R3 3.3 pF • • • • • • B, C, D3R6 3.6 pF • • • • • • B, C, D3R9 3.9 pF • • • • • • B, C, D4R3 4.3 pF • • • • • • B, C, D4R7 4.7 pF • • • • • • B, C, D5R1 5.1 pF • • • • • • B, C, D5R6 5.6 pF • • • • • • B, C, D6R2 6.2 pF • • • • • • B, C, D6R8 6.8 pF • • • • • • B, C, D7R5 7.5 pF • • • • • • B, C, D8R2 8.2 pF • • • • • • B, C, D9R1 9.1 pF • • • • • • B, C, D100 10 pF • • • • • • F, G, J, K, M110 11 pF • • • • • • F, G, J, K, M120 12 pF • • • • • • F, G, J, K, M130 13 pF • • • • • • F, G, J, K, M150 15 pF • • • • • • F, G, J, K, M160 16 pF • • • • • • F, G, J, K, M180 18 pF • • • • • • F, G, J, K, M200 20 pF • • • • • • F, G, J, K, M220 22 pF • • • • • • F, G, J, K, M240 24 pF • • • • • • F, G, J, K, M270 27 pF • • • • • • F, G, J, K, M300 30 pF • • • • • • F, G, J, K, M330 33 pF • • • • • • F, G, J, K, M360 36 pF • • • • • • F, G, J, K, M390 39 pF • • • • • • F, G, J, K, M430 43 pF • • • • • • F, G, J, K, M470 47 pF • • • • • • F, G, J, K, M510 51 pF • • • • • • F, G, J, K, M560 56 pF • • • • • • F, G, J, K, M620 62 pF • • • • • • F, G, J, K, M680 68 pF • • • • • • F, G, J, K, M750 75 pF • • • • • • F, G, J, K, M820 82 pF • • • • • • F, G, J, K, M910 91 pF • • • • • • F, G, J, K, M
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
• Plastic carrier tape- For tolerance B contact [email protected]
Revision: 23-Jan-15 124 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
101 100 pF • • • • • • F, G, J, K, M111 110 pF • • • • • F, G, J, K, M121 120 pF • • • • • F, G, J, K, M131 130 pF • • • • • F, G, J, K, M151 150 pF • • • • • F, G, J, K, M161 160 pF • • • • • F, G, J, K, M181 180 pF • • • • • F, G, J, K, M201 200 pF • • • • F, G, J, K, M221 220 pF • • • • F, G, J, K, M241 240 pF • • • • F, G, J, K, M271 270 pF • • • • F, G, J, K, M301 300 pF • • • • F, G, J, K, M331 330 pF • • • • F, G, J, K, M361 360 pF • • • • F, G, J, K, M391 390 pF • • • • F, G, J, K, M431 430 pF • • • F, G, J, K, M471 470 pF • • • F, G, J, K, M511 510 pF • • • F, G, J, K, M561 560 pF • • • F, G, J, K, M621 620 pF • • • F, G, J, K, M681 680 pF • • • F, G, J, K, M751 750 pF • • • F, G, J, K, M821 820 pF • • F, G, J, K, M911 910 pF • • F, G, J, K, M102 1.0 nF • • F, G, J, K, M112 1.1 nF • • F, G, J, K, M122 1.2 nF • • F, G, J, K, M152 1.5 nF • • F, G, J, K, M182 1.8 nF • • F, G, J, K, M222 2.0 nF • • F, G, J, K, M242 2.4 nF • F, G, J, K, M272 2.7 nF • F, G, J, K, M302 3.0 nF • F, G, J, K, M332 3.3 nF • F, G, J, K, M392 3.9 nF • F, G, J, K, M472 4.7 nF • F, G, J, K, M512 5.1 nF • F, G, J, K, M
SELECTION CHARTDIELECTRIC (VISHAY CODE) C0G (D)STYLE VJ3838
TOLERANCECASE CODE 3838VOLTAGE (VDC) 500 1000 2500 3600 5000 7200VOLTAGE CODE E G O W M S
CAP. CODE CAP.
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”
• Plastic carrier tape- For tolerance B contact [email protected]
Revision: 23-Jan-15 125 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
QUAD HIGH FREQ DIELECTRIC - TYPICAL PARAMETERS
0.01
0.1
1
10
100
10 100 1000
ES
R (Ω
)
FREQUENCY (MHz)
ESR VS. FREQUENCY SIZE 0505 QUAD RF MLCC
1 pF
10 pF
100 pF
1
10
100
1000
10 000
10 100 1000
Q
FREQUENCY (MHz)
Q VALUE VS. FREQUENCY SIZE 0505 QUAD RF MLCC
1 pF
10 pF
100 pF
0.1
1
10
1 10 100
SR
F (G
Hz)
CAPACITANCE (pF)
SRF VS. CAPACITANCE SIZE 0505 QUAD RF MLCC
0.1
1
10
1 10 100
CU
RR
EN
T (A
RM
S)
CAPACITANCE (pF)
1000 MHz
500 MHz
150 MHz
CURRENT RATING SIZE 0505 QUAD RF MLCC, EXT. VOLTAGE
0.001
0.01
0.1
1
10
100
10 100 1000
ES
R (Ω
)
FREQUENCY (MHz)
ESR VS. FREQUENCY SIZE 1111 QUAD RF MLCC
1.5 pF
10 pF
180 pF
1000 pF
1
10
100
1000
10 000
10 100 1000
Q
FREQUENCY (MHz)
Q VALUE VS. FREQUENCY SIZE 1111 QUAD RF MLCC
1.5 pF
10 pF
180 pF
1000 pF
Revision: 23-Jan-15 126 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
QUAD HIGH FREQ DIELECTRIC - TYPICAL PARAMETERS
0.1
1
10
1 10 100 1000
SR
F (G
Hz)
CAPACITANCE (pF)
SRF VS. CAPACITANCE SIZE 1111 QUAD RF MLCC
0.1
1
10
100
1 10 100 1000
CU
RR
EN
T (A
RM
S)
CAPACITANCE (pF)
1 GHz
150 MHz
30 MHz
CURRENT RATING SIZE 1111 QUAD RF MLCC, EXT. VOLTAGE
0.01
0.1
1
10
100
10 100 1000
ES
R (Ω
)
FREQUENCY (MHz)
ESR VS. FREQUENCY SIZE 2525 QUAD RF MLCC
1 pF
24 pF 100 pF
270 pF 1
10
100
1000
10 000
10 100 1000
Q
FREQUENCY (MHz)
Q VALUE VS. FREQUENCY SIZE 2525 QUAD RF MLCC
1 pF
24 pF
100 pF
270 pF
0.01
0.1
1
10
1 10 100 1000 10 000
SR
F (G
Hz)
CAPACITANCE (pF)
SRF VS. CAPACITANCESIZE 2525 QUAD RF MLCC
0.1
1
10
100
1 10 100 1000 10 000
CU
RR
EN
T (A
RM
S)
CAPACITANCE (pF)
10 MHz
500 MHz
150 MHz
30 MHz
CURRENT RATING SIZE 2525 QUAD RF MLCC, EXT. VOLTAGE
Revision: 23-Jan-15 127 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
QUAD HIGH FREQ DIELECTRIC - TYPICAL PARAMETERS
0.001
0.01
0.1
1
10 100 1000
ES
R (Ω
)
FREQUENCY (MHz)
ESR VS. FREQUENCYSIZE 3838 QUAD RF MLCC
100 pF
22 pF
390 pF180 pF
0.001
0.01
0.1
1
10 100 1000
ES
R (Ω
)
FREQUENCY (MHz)
ESR VS. FREQUENCYSIZE 3838 QUAD RF MLCC
680 pF
2200 pF
5100 pF
1
10
100
1000
10 000
10 100 1000
Q
FREQUENCY (MHz)
Q VALUE VS. FREQUENCYSIZE 3838 QUAD RF MLCC
22 pF
100 pF
180 pF390 pF
1
10
100
1000
10 000
1 10 100 1000
Q
FREQUENCY (MHz)
Q VALUE VS. FREQUENCYSIZE 3838 QUAD RF MLCC
2200 pF
5100 pF
680 pF
10
100
1000
10 000
1 10 100 1000 10 000
SR
F (M
Hz)
CAPACITANCE (pF)
SRF VS. CAPACITANCESIZE 3838 QUAD RF MLCC
0.01
0.1
1
10
100
1 10 100 1000 10 000
CU
RR
EN
T (A
RM
S)
CAPACITANCE (pF)
30 MHz
2 MHz
10 MHz
CURRENT RATINGSIZE 3838 QUAD RF MLCC, EXT. VOLTAGE
Revision: 23-Jan-15 128 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QUAD HIFREQ Serieswww.vishay.com Vishay Vitramon
Notes(1) Vishay Vitramon uses embossed plastic carrier tape(2) REFERENCE: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(3) n/a = not available(4) Final quantities for packaging can depend on product thickness
STANDARD PACKAGING QUANTITIES (1)(2)(3)(4)
CASE CODE TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES WAFFLE PACK
PLASTIC TAPEPACKAGING CODE
“T”
LOW QUANTITY“J”
PLASTIC TAPEPACKAGING CODE
“R”
PLASTIC WAFFLE PACKPACKAGING CODE
“W”
0505 8 mm 3000 1000 10 000 n/a
1111 8 mm 2500 1000 10 000 n/a
2525 12 mm 1000 500 n/a 81
3838 16 mm 400 n/a n/a 35
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to 40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment (1 year for copper).
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
QUAD HIGH FREQ DIELECTRIC - TYPICAL PARAMETERS
- 75 - 50 - 25 0 50 100 125
2.0
1.5
1.0
0.5
0.0
- 0.5
- 1.0
- 1.5
- 2.0
NP0
TEMPERATURE °C
150 175 25 75
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE COEFFICIENT OF CAPACITANCE
TEMPERATURE °C
MIN. INSULATION RESISTANCE VS. TEMPERATURE
10 25 100 150
10 000
1000
100
1050
INS
UL
AT
ION
RE
SIS
TAN
CE
(ΩF
)
AGING RATE
HOURS
100 1000 10 000
% C
APA
CIT
AN
CE
CH
AN
GE
0.2
0.1
0.0
- 0.1
- 0.21 10
0.2
0.1
0.0
- 0.1
- 0.2
DC VOLTS APPLIED
VOLTAGE COEFFICIENT OF CAPACITANCE
% C
APA
CIT
AN
CE
CH
AN
GE
0 10 20 30 40 50 60 70 80 90 100
Revision: 23-Jan-15 129 Document Number: 45221For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ High Qwww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitorsfor High Frequency Applications
FEATURES• Ultra-stable dielectric offering a Temperature
Coefficient of Capacitance (TCC) of0 ppm/°C ± 30 ppm/°C over the entiretemperature range
• Low Dissipation Factor (DF)
• Wet build process
• Reliable Noble Metal Electrode (NME)system
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
APPLICATIONS• Ideal for critical timing applications
• Ideal for tuning applications
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at + 25 °C unless otherwise specified.
Operating Temperature: - 55 °C to + 150 °C
Voltage Range: 50 VDC to 200 VDC
Capacitance Range: 1.0 pF to 220 pF
Temperature Coefficient of Capacitance (TCC): 0 ppm/°C ± 30 ppm/°C from - 55 °C to + 125 °C
Dissipation Factor (DF): 0.1 % maximum at 1.0 VRMS and 1 MHz for values 1000 pF0.1 % maximum at 1.0 VRMS and 1 kHz for values > 1000 pF
Aging Rate: 0 % maximum per decade
Insulation Resistance (IR): At + 25 °C and rated voltage 100 000 M minimum or,1000 F whichever is less.At + 125 °C and rated voltage 10 000 M minimum or100 F, whichever is less.
Dielectric Strength Test:Performed per method 103 of EIA 198-2-E.Applied test voltages: 200 VDC-rated: 250 % of rated voltage
Available
Revision: 27-Mar-13 130 Document Number: 45050For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ High Qwww.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
Notes• Size 0402 available with Vishay Basic Commodity series, see datasheet: www.vishay.com/doc?28534(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected](2) Process code may be added with up to three digits, used to control non-standard products and /or special requirements.(3) Termination code “E” is for conductive epoxy assembly.
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE(V)
CAPACITANCE
MINIMUM MAXIMUM
HIGH Q C0G (NP0)
0603 100 1.0 pF 100 pF
0805 200 1.0 pF 220 pF
ORDERING INFORMATIONVJ0805 Q 101 K X A A C ### (2)
CASECODE
DIELECTRIC CAPACITANCENOMINAL
CODE
CAPACITANCETOLERANCE
TERMINATION DC VOLTAGERATING (1)
MARKING PACKAGING PROCESSCODE
06030805
Q = HIGH Q Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is a
multiplier. An“R” indicates adecimal point.
Examples:101 = 100 pF1R8 = 1.8 pF
B = ± 0.10 pFC = ± 0.25 pF D = ± 0.5 pF
F = ± 1 % G = ± 2 %J = ± 5 %
K = ± 10 %Note
B, C, D < 10 pFF, G, J, K 10 pF
X = Ni barrier100 % tin platedF, E = AgPd (3)
A = 50 VB = 100 VC = 200 V
A = Unmarked
C = 7" reel/paper tapeO = reel/flamed paper tapeI = 11 1/4"/13" reel/flamed
paper tapeP = 11 1/4"/13" reel/
paper tapeNote
“O” and “I” are used for“F” and “E” termination
ENVIRONMENTAL STATUSTERMINATION CODE TERMINATION DESCRIPTION RoHS COMPLIANT VISHAY GREEN
X Ni barrier 100 % tin plated matte finish Yes Yes
E AgPd Yes Yes
F AgPd Yes No
DIMENSIONS in inches (millimeters)
CASE CODE STYLE LENGTH
(L)WIDTH
(W)
MAXIMUM THICKNESS
(T)
TERMINATION (P)
MINIMUM MAXIMUM
0603 VJ0603 0.063 ± 0.006(1.60 ± 0.15)
0.031 ± 0.006(0.80 ± 0.15)
0.036(0.92)
0.012 (0.30)
0.018 (0.46)
0805 VJ0805 0.079 ± 0.008 (2.00 ± 0.20)
0.049 ± 0.008(1.25 ± 0.20)
0.057(1.45)
0.010(0.25)
0.028 (0.71)
LW
TMAX.
P
Revision: 27-Mar-13 131 Document Number: 45050For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ High Qwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Available in paper carrier tape only
Note(1) Reference: EIA standard RS481 - “Taping of Surface Mount Components for Automatic Placement”
SELECTION CHARTDIELECTRIC HIGH QSTYLE VJ0603 VJ0805CASE CODE 0603 0805VOLTAGE (VDC) 50 100 50 100 200VOLTAGE CODE A B A B CCAP. CODE CAP.1R0 1.0 pF •• •• •• •• ••1R2 1.2 pF •• •• •• •• ••1R5 1.5 pF •• •• •• •• ••1R8 1.8 pF •• •• •• •• ••2R2 2.2 pF •• •• •• •• ••2R7 2.7 pF •• •• •• •• ••3R3 3.3 pF •• •• •• •• ••3R9 3.9 pF •• •• •• •• ••4R7 4.7 pF •• •• •• •• ••5R6 5.6 pF •• •• •• •• ••6R8 6.8 pF •• •• •• •• ••8R2 8.2 pF •• •• •• •• ••100 10 pF •• •• •• •• ••120 12 pF •• •• •• •• ••150 15 pF •• •• •• •• ••180 18 pF •• •• •• •• ••220 22 pF •• •• •• •• ••270 27 pF •• •• •• •• ••330 33 pF •• •• •• •• ••390 39 pF •• •• •• •• ••470 47 pF •• •• •• •• ••560 56 pF •• •• •• •• ••680 68 pF •• •• •• •• ••820 82 pF •• •• •• •• ••101 100 pF •• •• •• •• ••121 120 pF •• •• ••
151 150 pF •• •• ••
181 180 pF •• ••
221 220 pF •• ••
HIGH Q PACKAGING QUANTITIES (1)
CASE CODE TAPE SIZE7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIESPACKAGING CODE
“C”/“O”PACKAGING CODE
“P”/“I”0603 8 mm 4000 10 0000805 8 mm 3000 10 000
STORAGE AND HANDLING CONDITIONS(1) Store the components at 5 °C to + 40 °C ambient temperature and 70 % related humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 27-Mar-13 132 Document Number: 45050For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ High Qwww.vishay.com Vishay Vitramon
HIGH Q DIELECTRIC - TYPICAL PARAMETERS
- 75 - 50 - 25 0 50 100 125
2.0
1.5
1.0
0.5
0.0
- 0.5
- 1.0
- 1.5
- 2.0
NP0
TEMPERATURE °C
150 175 25 75
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE COEFFICIENT OF CAPACITANCE
TEMPERATURE °C
MIN. INSULATION RESISTANCE VS. TEMPERATURE
10 25 100 150
10 000
1000
100
1050
INS
UL
AT
ION
RE
SIS
TAN
CE
(ΩF
)
AGING RATE
HOURS
100 1000 10 000
% C
APA
CIT
AN
CE
CH
AN
GE
0.2
0.1
0.0
- 0.1
- 0.21 10
0.2
0.1
0.0
- 0.1
- 0.2
DC VOLTS APPLIED
VOLTAGE COEFFICIENT OF CAPACITANCE
% C
APA
CIT
AN
CE
CH
AN
GE
0 10 20 30 40 50 60 70 80 90 100
CHANGE OF CAPACITANCE WITH FREQUENCY
FREQUENCY
1 kHz 10 kHz 100 kHz 1 MHz
+ 2
+ 1
0
- 1
- 2
% C
APA
CIT
AN
CE
CH
AN
GE
1 100
10
1
10 10000.1
0805
0603
SERIES RESONANT FREQUENCY
RE
SO
NA
NT
FR
EQ
UE
NC
Y (
GH
z)
CAPACITANCE (pF)
100 1000
1
Q
10
100
10 000
100010 pF
100 pF
FREQUENCY (MHz)
Q VS. FREQUENCY - VJ0805, 50 V
100 1000
1
ES
R
(Ω)
0.1
0.01
10 pF
100 pF
ESR VS. FREQUENCY - VJ0805, 50 V
FREQUENCY (MHz)
Revision: 27-Mar-13 133 Document Number: 45050For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC High Q Dielectricwww.vishay.com Vishay
Surface Mount Multilayer Ceramic Chip Capacitorsfor High Q Commodity Applications
FEATURES• Ultra stable class 1 dielectric
• High Q and low ESR at high frequency
• Four standard sizes
• High capacitance per unit volume
• Supplied in tape on reel
• For high frequency applications
• Ni-barrier with 100 % tin terminations
• Dry sheet manufacturing technology
• Noble Metal Electrode system (NME)
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
APPLICATIONS• Mobile telecommunication
• WLAN
• RF modules
• Tuner
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at 25 °C, 30 % to 70 % related humidity,
unless otherwise specified
Operating Temperature: - 55 °C to + 125 °C
Capacitance Range: 0.5 pF to 3300 pF
Voltage Range: 16 VDC to 100 VDC
Temperature Coefficient of Capacitance (TCC): ± 30 ppm/°C from - 55 °C to + 125 °C
Dissipation Factor: Cap. < 30 pF: Q 400 + 20 CCap. 30 pF: Q 1000
Test Conditions for Capacitance and DF MeasurementCap. 1000 pF 1.0 VRMS ± 0.2 VRMS, 1 MHz ± 10 %Cap. > 1000 pF 1.0 VRMS ± 0.2 VRMS, 1 kHz ± 10 %
Aging Rate: 0 % maximum per decade
Insulation Resistance (IR): after 120 s at UR (DC)10 G or R x C 500 x F whichever is less
Dielectric Strength Test:This is the maximum voltage the capacitors are tested for1 s to 5 s period and the charge/discharge current does notexceed 50 mA 100 VDC: DWV at 250 % of rated voltage
Revision: 23-Jan-13 134 Document Number: 28534For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC High Q Dielectricwww.vishay.com Vishay
Note• Detail ratings see selection chart
QUICK REFERENCE DATA
DIELECTRIC CASEMAXIMUM VOLTAGE
(V)
CAPACITANCE
MINIMUM MAXIMUM
High Q0402 50 0.5 pF 470 pF
0603 100 0.5 pF 3.3 nF
ORDERING INFORMATION
VJ0402 Q 101 F X J C W1BCSIZE
CODEDIELECTRIC CAPACITANCE TOLERANCE TERMINATION VOLTAGE PACKAGING PROCESS CODE FOR
BASIC COMMODITY
0402 0603
Q = High Q Two significant digits followed by
the number of zeros:
1R0 = 1.0 pF101 = 100 pF
Cap. value 5 pFB = ± 0.10 pFC = ± 0.25 pF
5 pF > Cap. value < 10 pFC = ± 0.25 pFD = ± 0.50 pF
Cap. value 10 pFF = ± 1 %G = ±2 %J = ±5 %
X = Ni barrier 100 % tin
termination
J = 16 VX = 25 VA = 50 V
B = 100 V
C = 7" reel/paper
P = 13" reel/paper
DIMENSIONS in inches (millimeters)
SIZE CODE
L WT
MAX.MB
0402(1005)
0.040 ± 0.002(1.00 ± 0.05)
0.020 ± 0.002(0.50 ± 0.05)
0.022(0.55)
0.010 + 0.002/- 0.004(0.25 + 0.05/- 0.10)
0603 (1608)
0.063 + 0.006/- 0.004(1.60 + 0.15/- 0.10)
0.030 + 0.006/- 0.004(0.80 + 0.15/- 0.10)
0.038(0.95)
0.016 ± 0.006(0.40 ± 0.15)
T
L
MB MB
W
Revision: 23-Jan-13 135 Document Number: 28534For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC High Q Dielectricwww.vishay.com Vishay
Note• Letters indicate product thickness, see packaging quantities
SELECTION CHARTDIELECTRIC HIGH QSTYLE VJ0402 VJ0603SIZE CODE 0402 0603VOLTAGE (VDC) 16 V 25 V 50 V 100 V 16 V 25 V 50 V 100 VVOLTAGE CODE J X A B J X A BCAP. CODE CAP.0R5 0.5 pF N N S S S1R0 1.0 pF N N S S S1R2 1.2 pF N N S S S1R5 1.5 pF N N S S S1R8 1.8 pF N N S S S2R2 2.2 pF N N S S S2R7 2.7 pF N N S S S3R3 3.3 pF N N S S S3R9 3.9 pF N N S S S4R7 4.7 pF N N S S S5R6 5.6 pF N N S S S6R8 6.8 pF N N S S S8R2 8.2 pF N N S S S100 10 pF N N S S S120 12 pF N N S S S150 15 pF N N S S S180 18 pF N N S S S220 22 pF N N S S S270 27 pF N N S S S330 33 pF N N S S S390 39 pF N N S S S470 47 pF N N S S S560 56 pF N N S S S680 68 pF N N S S S820 82 pF N N S S S101 100 pF N N S S S121 120 pF N N S S S151 150 pF N N S S S181 180 pF N N S S S221 220 pF N N S S S271 270 pF N N N S S S331 330 pF N N N S S S391 390 pF N N N S S S471 470 pF N N N S S S561 560 pF S S S681 680 pF S S S821 820 pF S S S102 1000 pF S S S122 1200 pF X X X152 1500 pF X X X182 1800 pF X X X222 2200 pF X X X272 2700 pF X X X332 3300 pF X X X472 4700 pF562 5600 pF682 6800 pF822 8200 pF103 10 000 pF
Revision: 23-Jan-13 136 Document Number: 28534For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC High Q Dielectricwww.vishay.com Vishay
PAPER TAPE SPECIFICATION
REEL SPECIFICATIONS
PACKAGING QUANTITIES
SIZE CODE(inch/mm)
MAX. THICKNESS (mm)
THICKNESS SYMBOLPAPER TAPE
7" REEL (C) 13" REEL (P)
0402 (1002) 0.55 N 10K 20K
0603 (1608) 0.95 S, X 4K 15K
FW
D0
P0
P2
P1
A0
B0
E
B
A D C
DIMENSIONS OF PAPER TAPE in millimeters
SYM. PRODUCT SIZE CODE
0402 0603
A0 0.62 ± 0.05 1.02 ± 0.05
B0 1.12 ± 0.05 1.80 ± 0.05
W 8.00 ± 0.10 8.00 ± 0.10
E 1.75 ± 0.05 1.75 ± 0.05
F 3.50 ± 0.05 3.50 ± 0.05
D0 1.55 ± 0.05 1.55 ± 0.05
P0 4.00 ± 0.10 4.00 ± 0.10
P1 2.00 ± 0.05 4.00 ± 0.10
P2 2.00 ± 0.05 2.00 ± 0.05
REEL DIMENSIONS AND TAPE WIDTH in millimeters
Ø 180 mm; 7" Ø 330 mm; 13"
A 13.0 ± 0.5 13.0 ± 0.5
B 9.0 ± 1.0 9.0 ± 1.0
C 178.0 ± 1.0 330.0 ± 1.0
D 60.0 ± 1.0 100.0 ± 1.0
Revision: 23-Jan-13 137 Document Number: 28534For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC High Q Dielectricwww.vishay.com Vishay
TYPICAL ELECTRICAL CHARACTERISTICS
Q VALUE CRITERIA VS. SPECIFIC FREQUENCYSIZE 0402
10 000
1000
100
10
10.1 1 10 100
CAPACITANCE (pF)
Q
500 MHz1 GHz 100 MHz
minimum (solid line)typical (broken line)
Q VALUE CRITERIA VS. SPECIFIC FREQUENCYSIZE 0603
10 000
1000
100
10
10.1 1 10 100
CAPACITANCE (pF)
Q
500 MHz1 GHz 100 MHz
minimum (solid line)typical (broken line)
TYPICAL ESR VS. FREQUENCYSIZE 0402
1
0.1
0.01100 1000 10 000
FREQUENCY (MHz)
ES
R (
Ω)
1pF
100 pF5 pF
10 pF
TYPICAL ESR VS. FREQUENCYSIZE 0603
1
0.1
0.01100 1000 10 000
FREQUENCY (MHz)
ES
R (
Ω)
10
1 pF
4.7 pF
10 pF
68 pF
TYPICAL IMPEDANCE VS. FREQUENCYSIZE 0402
1
0.1100 1000 10 000
FREQUENCY (MHz)
IMP
ED
AN
CE
(Ω
)
10
10
100 000
10 000
1000
100
100 pF
1 pF
4.7 pF
10 pF
TYPICAL IMPEDANCE VS. FREQUENCYSIZE 0603
1
0.1100 1000 10 000
FREQUENCY (MHz)
IMP
ED
AN
CE
(Ω
)
10
100
100
100 000
10 000
10001 pF
4.7 pF
10 pF68 pF
SRF VS. CAPACITANCE
1000
10 000
1001 10 100
CAPACITANCE (pF)SE
RIE
S R
ES
ON
AN
T F
RE
QU
EN
CY
(M
Hz)
0603
0402
Revision: 23-Jan-13 138 Document Number: 28534For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC High Q Dielectricwww.vishay.com Vishay
CONSTRUCTION
NO. NAME HIGH Q
1 Ceramic material BaTiO3 based
2 Inner electrode AgPd alloy
3
Termination
Inner layer Ag
4 Middle layer Ni
5 Outer layer Sn (matt)
STORAGE AND HANDLING CONDITIONS
(1) To store products at 5 °C to 40 °C ambient temperature and 20 % to 70 % related humidity conditions.(2) The product is recommended to be used within one year after shipment. Check solderability in case of shelf life extension is needed.
Cautions:a. Do not store products in a corrosive environment such as sulfide, chloride gas, or acid. It may cause oxidization of electrode, which
easily be resulted in poor soldering.b. To store products on the shelf and avoid exposure to moisture.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
12
3
4
5
Revision: 23-Jan-13 139 Document Number: 28534For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Ultra High Q/Low ESRwww.vishay.com Vishay
Surface Mount Multilayer Ceramic Chip Capacitorsfor Ultra High Q Commodity Applications
FEATURES• Ultra stable class 1 dielectric
• Ultra High Q and low ESR at high frequency
• Four standard sizes
• High SRF characteristic
• Ultra low capacitance to 0.1 pF
• High precision capacitance tolerance ± 0.05 pF
• Supplied in tape on reel
• Ni-barrier with 100 % tin terminations
• Dry sheet manufacturing technology
• Base Metal Electrode system (BME)
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
APPLICATIONS• Mobile telecommunication
• WLAN
• RF modules
• Tuner
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at 25 °C, 30 % to 70 % related humidity,
unless otherwise specified
Operating Temperature: - 55 °C to + 125 °C
Capacitance Range: 0.1 pF to 100 pF
Voltage Range: 10 VDC to 250 VDC
Temperature Coefficient of Capacitance (TCC): 0 ppm/°C ± 30 ppm/°C from - 55 °C to + 125 °C0201: 22 pF: 0 ppm/°C ± 60 ppm/°C from - 55 °C to + 125 °C
Dissipation Factor:Cap < 30 pF: Q 400 + 20 CCap 30 pF: Q 1000
Test Conditions for Capacitance and DF Measurement:Cap. 1000 pF 1.0 VRMS ± 0.2 VRMS, 1 MHz ± 10 %Cap. > 1000 pF 1.0 VRMS ± 0.2 VRMS, 1 kHz ± 10 %
Aging Rate: 0 % maximum per decade
Insulation Resistance (IR): after 120 s at UR (DC)
10 G or R x C 500 x F whichever is less
Dielectric Strength Test:
This is the maximum voltage the capacitors are tested for1 s to 5 s period and the charge/discharge current does notexceed 50 mA 100 VDC: DWV at 250 % of rated voltage250 VDC: DWV at 200 % of rated voltage
Revision: 23-Jan-13 140 Document Number: 28547For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Ultra High Q/Low ESRwww.vishay.com Vishay
Note• Detail ratings see “Selection Chart”
Note(1) Details see “Selection Chart”
QUICK REFERENCE DATA
DIELECTRIC CASEMAXIMUM VOLTAGE
(V)
CAPACITANCE
MINIMUM MAXIMUM
Ultra High Q
0201 25 0.1 pF 33 pF
0402 100 0.1 pF 22 pF
0603 250 0.3 pF 47 pF
0805 250 0.3 pF 100 pF
ORDERING INFORMATIONVJ0402 L 100 F X A C W1BC
SIZE CODE DIELECTRIC CAPACITANCE TOLERANCE (1) TERMINATION VOLTAGE PACKAGING PROCESSCODE FOR
BASICCOMMODITY
0201040206030805
L = Ultra High Q
Expressed in pFtwo significantdigits followedby the number
of zeros:0R3 = 0.3 pF1R0 = 1.0 pF150 = 15 pF
Cap. value 5 pFV = ± 0.05 pFB = ± 0.10 pFC = ± 0.25 pFD = ± 0.50 pF
5 pF > Cap. value < 10 pFB = ± 0.10 pFC = ± 0.25 pFD = ± 0.50 pF
Cap. value 10 pFF = ± 1 %G = ± 2 %J = ± 5 %
X = Ni barrier100 % tin
termination
Q = 10 VX = 25 VA = 50 V
B = 100 VP = 250 V
C = 7" reel/paper tape
P = 13" reel/paper tape
DIMENSIONS in inches [millimeters]
SIZE CODE L W
T MAX.
MB
0201(0603)
0.024 ± 0.0012(0.60 ± 0.03)
0.012 ± 0.0012(0.30 ± 0.03)
0.013(0.33)
0.006 ± 0.002(0.15 ± 0.05)
0402 (1005)
0.040 ± 0.002(1.00 ± 0.05)
0.020 ± 0.002(0.50 ± 0.05)
0.022(0.55)
0.010 + 0.002/- 0.004(0.25 + 0.05/- 0.10)
0603 (1608)
0.063 ± 0.004(1.60 ± 0.10)
0.030 ± 0.004(0.80 ± 0.10)
0.035(0.87)
0.015 ± 0.006(0.40 ± 0.15)
0805 (2012)
0.080 ± 0.008(2.00 ± 0.20)
0.050 ± 0.008(1.25 ± 0.20)
0.038(0.95)
0.020 ± 0.008(0.50 ± 0.20)
T
LMB MB
W
Revision: 23-Jan-13 141 Document Number: 28547For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Ultra High Q/Low ESRwww.vishay.com Vishay
Note• Letters indicate product thickness, see “Packaging Quantities”
SELECTION CHARTDIELECTRIC ULTRA HIGH Q
STYLE VJ0201 VJ0402 VJ0603 VJ0805
TOLERANCESIZE CODE 0201 0402 0603 0805
VOLTAGE VDC 10 V 25 V 50 V 100 V 50 V 100 V 250 V 50 V 100 V 250 V
VOLTAGE CODE Q X A B A B P A B P
CAP. CODE CAP.
0R1 0.1 pF L L N N B
0R2 0.2 pF L L N N V, B
0R3 0.3 pF L L N N S S S T T T V, B
0R4 0.4 pF L L N N S S S T T T V, B
0R5 0.5 pF L L N N S S S T T T V, B, C
0R6 0.6 pF L L N N S S S T T T V, B, C
0R7 0.7 pF L L N N S S S T T T V, B, C
0R8 0.8 pF L L N N S S S T T T V, B, C
0R9 0.9 pF L L N N S S S T T T V, B, C
1R0 1.0 pF L L N N S S S T T T V, B, C
1R2 1.2 pF L L N N S S S T T T V, B, C
1R5 1.5 pF L L N N S S S T T T V, B, C
1R8 1.8 pF L L N N S S S T T T V, B, C
2R2 2.2 pF L L N N S S S T T T V, B, C
2R4 2.4 pF S V, B, C
2R7 2.7 pF L L N N S S S T T T V, B, C
3R3 3.3 pF L L N N S S S T T T V, B, C
3R9 3.9 pF L L N N S S S T T T V, B, C
4R7 4.7 pF L L N N S S S T T T V, B, C
5R6 5.6 pF L L N N S S S T T T B, C, D
6R8 6.8 pF L L N N S S S T T T B, C, D
8R2 8.2pF L L N N S S S T T T B, C, D
100 10 pF L L N N S S S T T T F, G, J
110 11 pF L L N S S S T T T F, G, J
120 12 pF L L N S S S T T T F, G, J
130 13 pF L L N S S S T T T F, G, J
150 15 pF L L N S S S T T T F, G, J
160 16 pF L L N S S S T T T F, G, J
180 18 pF L L N S S S T T T F, G, J
200 20 pF L N S S S T T T F, G, J
220 22 pF L N S S S T T T F, G, J
240 24 pF L S S S T T T F, G, J
270 27 pF L S S S T T T F, G, J
300 30 pF L S S S T T T F, G, J
330 33 pF L S S S T T T F, G, J
360 36 pF S S S T T T F, G, J
390 39 pF S S S T T T F, G, J
430 43 pF S S S T T T F, G, J
470 47 pF S S S T T T F, G, J
560 56 pF T T T F, G, J
680 68 pF T T T F, G, J
820 82 pF T T T F, G, J
101 100 pF T T T F, G, J
Revision: 23-Jan-13 142 Document Number: 28547For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Ultra High Q/Low ESRwww.vishay.com Vishay
PAPER TAPE SPECIFICATION
REEL SPECIFICATIONS
PACKAGING QUANTITIES
SIZE CODE(inch/mm)
THICKNESS(mm)
THICKNESSSYMBOL
PAPER TAPE
7" REEL (C) 13" REEL (P)
0201 (0603) 0.30 ± 0.03 L 15K -
0402 (1002) 0.50 ± 0.05 N 10K 50K
0603 (1608) 0.80 ± 0.07 S 4K 15K
0805 (2012) 0.85 ± 0.10 T 4K 15K
FW
P0
P2D0
B0
A0P1
E
B
A D C
DIMENSIONS OF PAPER TAPE in millimeters
SYM.PRODUCT SIZE CODE
0201 0402 0603 0805
A0 0.37 ± 0.03 0.62 ± 0.05 1.02 ± 0.05 1.50 ± 0.10
B0 0.67 ± 0.03 1.12 ± 0.05 1.82 ± 0.05 2.30 ± 0.10
W 8.00 ± 0.10 8.00 ± 0.10 8.00 ± 0.10 8.00 ± 0.10
E 1.75 ± 0.05 1.75 ± 0.05 1.75 ± 0.05 1.75 ± 0.05
F 3.50 ± 0.05 3.50 ± 0.05 3.50 ± 0.05 3.50 ± 0.05
D0 1.55 ± 0.05 1.55 ± 0.05 1.55 ± 0.05 1.55 ± 0.05
P0 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10
P1 2.00 ± 0.05 2.00 ± 0.05 4.00 ± 0.10 4.00 ± 0.10
P2 2.00 ± 0.05 2.00 ± 0.05 2.00 ± 0.05 2.00 ± 0.05
REEL DIMENSIONS AND TAPE WIDTH in millimetersSYM. Ø 180 mm; 7" Ø 330 mm; 13"
A 13.0 ± 0.5 13.0 ± 0.5
B 9.0 ± 1.0 9.0 ± 1.0
C 178.0 ± 1.0 330.0 ± 1.0
D 60.0 ± 1.0 100.0 ± 1.0
Revision: 23-Jan-13 143 Document Number: 28547For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Ultra High Q/Low ESRwww.vishay.com Vishay
ELECTRICAL CHARACTERISTICS
10 000
1000
100
10
1100 1000 10 000
FREQUENCY (MHz)
Q
1 pF
6.8 pF
TYPICAL Q VALUE VS.FREQUENCY SIZE 0402
FREQUENCY (GHz)
TYPICAL Q VALUE VS. FREQUENCYSIZE 0603, 250 V
10 000
100
10
1000
2.51.50.5 10 2 3.53
0.3 pF
3.3 pF
6.8 pF
QTYPICAL ESR VS. FREQUENCY
SIZE 04021
0.1
0.01100 1000 10 000
FREQUENCY (MHz)
ES
R (
Ω)
1 pF1.5 pF3.3 pF
6.8 pF
FREQUENCY (GHz)
TYPICAL ESR VS. FREQUENCYSIZE 0603, 250 V
10
0.1
0.01
1
2.51.50.5 10 2 3.53
0.3 pF
3.3 pF6.8 pF
ES
R (
Ω)
FREQUENCY (MHz)
TYPICAL IMPEDANCE VS. FREQUENCYSIZE 0402
100 000
10 000
100
10
1
1000
10 000100101 1000
1 pF1.5 pF3.3 pF
6.8 pF
IMP
ED
AN
CE
(Ω
)
Revision: 23-Jan-13 144 Document Number: 28547For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Ultra High Q/Low ESRwww.vishay.com Vishay
CONSTRUCTION
NO. NAME ULTRA HIGH Q
1 Ceramic material BaTiO3 based
2 Inner electrode Cu
3
Termination
Inner layer Cu
4 Middle layer Ni
5 Outer layer Sn (matt)
STORAGE AND HANDLING CONDITIONS
(1) To store products at 5 °C to 40 °C ambient temperature and 20 % to 70 % related humidity conditions.(2) The product is recommended to be used within one year after shipment. Check solderability in case of shelf life extension is needed.
Cautions:a. Do not store products in a corrosive environment such as sulfide, chloride gas, or acid. It may cause oxidization of electrode, which
easily be resulted in poor soldering.b. To store products on the shelf and avoid exposure to moisture.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
12
3
4
5
Revision: 23-Jan-13 145 Document Number: 28547For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Contents
VJ Non-Magnetic Series forIR Reflow Soldering ............... 147
VJ Non-Magnetic Series forEpoxy Bonding ...................... 163
MLCCsfor
Non-Magnetic
Applications
(NME Technology)
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitorsfor Non-Magnetic Applications (IR Reflow Soldering)
FEATURES• Manufactured with non-magnetic materials• Safety screened for magnetic properties• C0G (NP0) and X7R / X5R dielectrics• Wide range of case sizes, voltage ratings,
and capacitance values• Suitable for IR reflow assembly methods• Wet built process• Reliable Noble Metal Electrode (NME) system • Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS• Magnetic Resonance Imaging (MRI)• Medical test and diagnostic equipment• Laboratory analysis systems• Navigation and electronic test equipment• Audio amplifiers
ELECTRICAL SPECIFICATIONS
NON-MAGNETIC C0G (NP0)
GENERAL SPECIFICATIONNoteElectrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range: 1.0 pF to 39 nF
Voltage Range: 10 VDC to 3000 VDC
Temperature Coefficient of Capacitance (TCC):0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
Dissipation Factor (DF):0.1 % maximum at 1.0 VRMS and 1 MHz for values 1000 pF0.1 % maximum at 1.0 VRMS and 1 kHz for values > 1000 pF
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging: 0 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 200 VDC-rated: 250 % of rated voltage500 VDC-rated: 200 % of rated voltage630 VDC, 1000 VDC-rated: 150 % of rated voltage1500 VDC to 3000 VDC-rated: 120 % of rated voltage
NON-MAGNETIC X7R / X5R
GENERAL SPECIFICATIONNoteElectrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range: 100 pF to 6.8 μF
Voltage Range: 6.3 VDC to 3000 VDC
Temperature Coefficient of Capacitance (TCC):X5R: ± 15 % from -55 °C to +85 °C, with 0 VDC appliedX7R: ± 15 % from -55 °C to +125 °C, with 0 VDC applied
Dissipation Factor (DF): 6.3 V, 10 V ratings: 5 % maximum at 1.0 VRMS and 1 kHz16 V, 25 V ratings: 3.5 % maximum at 1.0 VRMS and 1 kHz 50 V ratings: 2.5 % maximum at 1.0 VRMS and 1 kHz
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 1 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 200 VDC-rated: 250 % of rated voltage500 VDC-rated: min. 150 % of rated voltage630 VDC, 1000 VDC-rated: min. 120 % of rated voltage1500 VDC, 3000 VDC-rated: 120 % of rated voltage
Revision: 27-Jan-15 147 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
QUICK REFERENCE DATA
DIELECTRIC CASEMAXIMUM VOLTAGE
(V)
CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0)
0402 100 1.0 pF 180 pF
0603 200 1.0 pF 1.5 nF
0805 500 1.0 pF 3.3 nF
1206 600 1.0 pF 10 nF
1210 500 1.0 pF 12 nF
1808 3000 10 pF 10 nF
1812 3000 10 pF 22 nF
1825 1000 15 pF 33 nF
2220 1000 100 pF 33 nF
2225 1000 120 pF 39 nF
X5R0402 16 27 nF 47 nF
0603 6.3 120 nF 150 nF
X7R
0402 100 100 pF 22 nF
0603 100 270 pF 100 nF
0805 200 390 pF 390 nF
1206 500 680 pF 1.0 μF
1210 500 1.0 nF 1.0 μF
1808 3000 220 pF 270 nF
1812 3000 270 pF 1.0 μF
1825 1000 10 nF 2.7 μF
2220 3000 1.0 nF 2.2 μF
2225 2000 5.6 nF 4.7 μF
3640 500 15 nF 6.8 μF
Revision: 27-Jan-15 148 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
Notes(1) DC voltage rating should not be exceeded in application (2) Selected values for X5R, see dielectric selection chart(3) For soldering conditions see Vishay Soldering Recommendations www.vishay.com/doc?45034
ORDERING INFORMATION VJ0603 Y 102 K C A A C
CASECODE
DIELECTRIC CAPACITANCENOMINAL CODE
CAPACITANCETOLERANCE
TERMINATION DC VOLTAGERATING (1)
MARKING PACKAGING
04020603080512061210180818121825222022253640
A = C0GY = X7R
G = X5R (2)
Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is a
multiplier. An “R”indicates a
decimal point.Examples
102 = 1000 pF1R0 = 1.0 pF
C0G (NP0):< 10 pF
C = ± 0.25 pF D = 0.5 pF 10 pF
F = ± 1 % G = ± 2 %J = ± 5 %
K = ± 10 %X5R / X7R:J = ± 5 %
K = ± 10 %M = ± 20 %
C (3) =non-magneticcopper barrier
termination
Q = 10 VJ = 16 VX = 25 VA = 50 VK = 75 V
B = 100 VC = 200 VE = 500 VL = 630 V
G = 1000 VR = 1500 VF = 2000 VH = 3000 V
A =unmarked
T = 7" reel / plastic tapeR = 11 1/4" / 13" reel / plastic tape
C = 7" reel / flamed paper tapeP = 11 1/4" / 13" reel /
flamed paper tapeJ = 7" reel (low quantity)
DIMENSIONS in inches (millimeters)
CASE CODE STYLE LENGTH
(L)WIDTH
(W)
MAXIMUM THICKNESS
(T)
TERMINATIONS(P)
MINIMUM MAXIMUM
0402 VJ0402 0.04 - 0.004 / + 0.005(1.02 - 0.10 / + 0.12)
0.020 - 0.004 / + 0.006(0.50 - 0.10 / + 0.14)
0.026(0.640)
0.004(0.100)
0.017(0.420)
0603 VJ0603 0.063 - 0.006 / + 0.008(1.60 - 0.15 / + 0.20)
0.031 - 0.006 / + 0.008(0.80 - 0.15 / + 0.20)
0.037(0.940)
0.012(0.300)
0.019(0.470)
0805 VJ0805 0.078 - 0.008 / + 0.010(2.00 - 0.20 / + 0.25)
0.049 - 0.008 / + 0.009(1.25 - 0.20 / + 0.23)
0.057(1.450)
0.010(0.250)
0.028(0.710)
1206 VJ1206 0.126 - 0.010 / + 0.012(3.20 - 0.25 / + 0.30)
0.063 - 0.010 / + 0.011(1.60 - 0.25 / + 0.28)
0.067(1.700)
0.010(0.250)
0.028(0.710)
1210 VJ1210 0.126 - 0.010 / + 0.012(3.20 - 0.25 / + 0.30)
0.098 - 0.010 / + 0.011(2.50 - 0.25 / + 0.28)
0.067(1.700)
0.010(0.250)
0.028(0.710)
1808 VJ1808 0.177 - 0.012 / + 0.014(4.50 - 0.30 / + 0.35)
0.078 - 0.010 / + 0.011(2.03 - 0.25 / + 0.28)
0.086(2.180)
0.010(0.250)
0.030(0.760)
1812 VJ1812 0.177 - 0.012 / + 0.014(4.50 - 0.30 / + 0.35)
0.126 - 0.010 / + 0.011(3.20 - 0.25 / + 0.28)
0.086(2.180)
0.010(0.250)
0.030(0.760)
1825 VJ1825 0.177 - 0.012 / + 0.014(4.50 - 0.30 / + 0.35)
0.252 - 0.010 / + 0.011(6.40 - 0.25 / + 0.28)
0.086(2.180)
0.010(0.250)
0.030(0.760)
2220 VJ2220 0.22 - 0.010 / + 0.012(5.59 - 0.25 / + 0.30)
0.200 - 0.010 / + 0.011(5.08 - 0.25 / + 0.28)
0.086(2.180)
0.010(0.250)
0.030(0.760)
2225 VJ2225 0.22 - 0.010 / + 0.012(5.59 - 0.25 / + 0.30)
0.250 - 0.010 / + 0.011(6.35 - 0.25 / + 0.28)
0.086(2.180)
0.010(0.250)
0.030(0.760)
3640 VJ3640 0.36 - 0.015 / + 0.017(9.14 - 0.38 / + 0.43)
0.400 - 0.015 / + 0.017(10.20 - 0.38 / + 0.43)
0.086(2.180)
0.010(0.250)
0.030(0.760)
LW
TMAX.
P
Revision: 27-Jan-15 149 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ0402 VJ0603 VJ0805CASE CODE 0402 0603 0805VOLTAGE (VDC) 10 16 25 50 100 10 16 25 50 100 200 10 16 25 50 100 200 500VOLTAGE CODE Q J X A B Q J X A B C Q J X A B C ECAP. CODE CAP.
1R0 1.0 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •1R2 1.2 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •1R5 1.5 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •1R8 1.8 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •2R2 2.2 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •2R7 2.7 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •3R3 3.3 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •3R9 3.9 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •4R7 4.7 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •5R6 5.6 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •6R8 6.8 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •8R2 8.2 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •100 10 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •120 12 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •150 15 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •180 18 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •220 22 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •270 27 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •330 33 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •390 39 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •470 47 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •560 56 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •680 68 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •820 82 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •101 100 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •121 120 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •151 150 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •181 180 pF •• •• •• •• •• •• •• •• •• •• • • • • • • • •221 220 pF •• •• •• •• •• • • • • • • • •271 270 pF •• •• •• •• •• • • • • • • • •331 330 pF •• •• •• •• •• • • • • • • •391 390 pF •• •• •• •• •• • • • • • • •471 470 pF •• •• •• •• • • • • • •561 560 pF •• •• •• •• • • • • • •681 680 pF •• •• •• •• • • • • • •821 820 pF •• •• •• • • • • • •102 1.0 nF •• •• •• • • • • •122 1.2 nF •• •• • • • • •152 1.5 nF •• •• • • • •182 1.8 nF • • • •222 2.2 nF • • • •272 2.7 nF • • •332 3.3 nF • •392 3.9 nF472 4.7 nF562 5.6 nF682 6.8 nF822 8.2 nF103 10 nF123 12 nF
Revision: 27-Jan-15 150 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1206 VJ1210CASE CODE 1206 1210VOLTAGE (VDC) 16 25 50 100 200 500 600 25 50 100 200 500VOLTAGE CODE J X A B C E N X A B C ECAP. CODE CAP.
1R0 1.0 pF • • • • • • • • • • • •1R2 1.2 pF • • • • • • • • • • • •1R5 1.5 pF • • • • • • • • • • • •1R8 1.8 pF • • • • • • • • • • • •2R2 2.2 pF • • • • • • • • • • • •2R7 2.7 pF • • • • • • • • • • • •3R3 3.3 pF • • • • • • • • • • • •3R9 3.9 pF • • • • • • • • • • • •4R7 4.7 pF • • • • • • • • • • • •5R6 5.6 pF • • • • • • • • • • • •6R8 6.8 pF • • • • • • • • • • • •8R2 8.2 pF • • • • • • • • • • • •100 10 pF • • • • • • • • • • • •120 12 pF • • • • • • • • • • • •150 15 pF • • • • • • • • • • • •180 18 pF • • • • • • • • • • • •220 22 pF • • • • • • • • • • • •270 27 pF • • • • • • • • • • • •330 33 pF • • • • • • • • • • • •390 39 pF • • • • • • • • • • • •470 47 pF • • • • • • • • • • • •560 56 pF • • • • • • • • • • • •680 68 pF • • • • • • • • • • • •820 82 pF • • • • • • • • • • • •101 100 pF • • • • • • • • • • • •121 120 pF • • • • • • • • • • • •151 150 pF • • • • • • • • • • • •181 180 pF • • • • • • • • • • • •221 220 pF • • • • • • • • • • • •271 270 pF • • • • • • • • • • • •331 330 pF • • • • • • • • • • • •391 390 pF • • • • • • • • • • • •471 470 pF • • • • • • • • • • • •561 560 pF • • • • • • • • • • • •681 680 pF • • • • • • • • • • • •821 820 pF • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • •122 1.2 nF • • • • • • • • • •152 1.5 nF • • • • • • • • • •182 1.8 nF • • • • • • • • • •222 2.2 nF • • • • • • • • •272 2.7 nF • • • • • • • • •332 3.3 nF • • • • • • • •392 3.9 nF • • • • • • • •472 4.7 nF • • • • • • • •562 5.6 nF • • • • • • •682 6.8 nF • • • • • •822 8.2 nF • • • • •103 10 nF • • • • •123 12 nF • •
Revision: 27-Jan-15 151 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1808 VJ1812CASE CODE 1808 1812VOLTAGE (VDC) 25 50 100 200 500 630 1000 1500 2000 3000 25 50 100 200 500 630 1000 1500 2000 3000VOLTAGE CODE X A B C E L G R F H X A B C E L G R F HCAP. CODE CAP.
100 10 pF • • • • • • • • • •120 12 pF • • • • • • • • • •150 15 pF • • • • • • • • • •180 18 pF • • • • • • • • • •220 22 pF • • • • • • • • • • • • • • •270 27 pF • • • • • • • • • • • • • • •330 33 pF • • • • • • • • • • • • • • •390 39 pF • • • • • • • • • • • • • • •470 47 pF • • • • • • • • • • • • • • • • • • • •560 56 pF • • • • • • • • • • • • • • • • • • • •680 68 pF • • • • • • • • • • • • • • • • • • • •820 82 pF • • • • • • • • • • • • • • • • • • • •101 100 pF • • • • • • • • • • • • • • • • • • • •121 120 pF • • • • • • • • • • • • • • • • • • •151 150 pF • • • • • • • • • • • • • • • • • • •181 180 pF • • • • • • • • • • • • • • • • • • •221 220 pF • • • • • • • • • • • • • • • • • • •271 270 pF • • • • • • • • • • • • • • • • •331 330 pF • • • • • • • • • • • • • • • • •391 390 pF • • • • • • • • • • • • • • • •471 470 pF • • • • • • • • • • • • • • • •561 560 pF • • • • • • • • • • • • • • • •681 680 pF • • • • • • • • • • • • • • • •821 820 pF • • • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • •272 2.7 nF • • • • • • • • •332 3.3 nF • • • • • • • • •392 3.9 nF • • • • • • • • •472 4.7 nF • • • • • • • •562 5.6 nF • • • • • • • •682 6.8 nF • • • • • • • •822 8.2 nF • • • • • • •103 10 nF • • • • • •123 12 nF • • • •153 15 nF • • •183 18 nF • •223 22 nF • •273 27 nF333 33 nF393 39 nF473 47 nF563 56 nF683 68 nF
Revision: 27-Jan-15 152 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1825 VJ2220 VJ2225CASE CODE 1825 2220 2225VOLTAGE (VDC) 25 50 100 200 500 630 1000 25 50 100 200 500 630 1000 25 50 100 200 500 630 1000VOLTAGE CODE X A B C E L G X A B C E L G X A B C E L GCAP. CODE CAP.
100 10 pF120 12 pF150 15 pF • •180 18 pF • •220 22 pF • •270 27 pF • •330 33 pF • •390 39 pF • •470 47 pF • •560 56 pF • •680 68 pF • •820 82 pF • •101 100 pF • • • • • • • • • • • •121 120 pF • • • • • • • • • • • • • • • • •151 150 pF • • • • • • • • • • • • • • • • •181 180 pF • • • • • • • • • • • • • • • • •221 220 pF • • • • • • • • • • • • • • • • •271 270 pF • • • • • • • • • • • • • • • • • • • • •331 330 pF • • • • • • • • • • • • • • • • • • • • •391 390 pF • • • • • • • • • • • • • • • • • • • • •471 470 pF • • • • • • • • • • • • • • • • • • • • •561 560 pF • • • • • • • • • • • • • • • • • • • • •681 680 pF • • • • • • • • • • • • • • • • • • • • •821 820 pF • • • • • • • • • • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • • • • • • • • •562 5.6 nF • • • • • • • • • • • • • • •682 6.8 nF • • • • • • • • • • • • • •822 8.2 nF • • • • • • • • • • • • • •103 10 nF • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • •183 18 nF • • • • • • • • • • •223 22 nF • • • • • • • • • • •273 27 nF • • • • • • • • • • •333 33 nF • • • • • • • • • • •393 39 nF • • • •473 47 nF563 56 nF683 68 nF
Revision: 27-Jan-15 153 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape(1) See selection chart for values only available as X5R. All other values X7R.
SELECTION CHARTDIELECTRIC X7R / X5R (1)
STYLE VJ0402 VJ0603 VJ0805CASE CODE 0402 0603 0805VOLTAGE (VDC) 6.3 10 16 25 50 100 6.3 10 16 25 50 100 10 16 25 50 100 200VOLTAGE CODE Y Q J X A B Y Q J X A B Q J X A B CCAP. CODE CAP.
101 100 pF •• •• •• •• •• ••121 120 pF •• •• •• •• •• ••151 150 pF •• •• •• •• •• ••181 180 pF •• •• •• •• •• ••221 220 pF •• •• •• •• •• ••271 270 pF •• •• •• •• •• •• •• •• •• •• •• ••331 330 pF •• •• •• •• •• •• •• •• •• •• •• ••391 390 pF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •471 470 pF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •561 560 pF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •681 680 pF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •821 820 pF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •102 1.0 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •122 1.2 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •152 1.5 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •182 1.8 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •222 2.2 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •272 2.7 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •332 3.3 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •392 3.9 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •472 4.7 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •562 5.6 nF •• •• •• •• •• •• •• •• •• •• •• • • • • • •682 6.8 nF •• •• •• •• •• •• •• •• •• •• •• • • • • • •822 8.2 nF •• •• •• •• •• •• •• •• •• •• •• • • • • • •103 10 nF •• •• •• •• •• •• •• •• •• •• •• • • • • • •123 12 nF •• •• •• •• •• •• •• •• •• •• • • • • • •153 15 nF •• •• •• •• •• •• •• •• •• •• • • • • • •183 18 nF •• •• •• •• •• •• •• •• •• • • • • • •223 22 nF •• •• •• •• •• •• •• •• •• • • • • • •273 27 nF X5R •• X5R •• X5R •• •• •• •• •• •• • • • • • •333 33 nF X5R •• X5R •• X5R •• •• •• •• •• •• • • • • •393 39 nF X5R •• •• •• •• •• •• • • • • •473 47 nF X5R •• •• •• •• •• •• • • • • •563 56 nF •• •• •• •• • • • • •683 68 nF •• •• •• •• • • • • •823 82 nF •• •• •• •• • • • • •104 100 nF •• •• •• •• • • • •124 120 nF X5R •• • • • •154 150 nF X5R •• • • • •184 180 nF • • •224 220 nF • • •274 270 nF • • •334 330 nF • • •394 390 nF •474 470 nF564 560 nF684 680 nF824 820 nF105 1.0 μF125 1.2 μF
Revision: 27-Jan-15 154 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1206 VJ1210CASE CODE 1206 1210VOLTAGE (VDC) 16 25 50 100 200 500 16 25 50 75 100 200 500VOLTAGE CODE J X A B C E J X A K B C ECAP. CODE CAP.
101 100 pF121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF331 330 pF391 390 pF471 470 pF561 560 pF681 680 pF • • • • • •821 820 pF • • • • • •102 1.0 nF • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • • •562 5.6 nF • • • • • • • • • • • • •682 6.8 nF • • • • • • • • • • • • •822 8.2 nF • • • • • • • • • • • • •103 10 nF • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • •273 27 nF • • • • • • • • • • • •333 33 nF • • • • • • • • • • • •393 39 nF • • • • • • • • • • • •473 47 nF • • • • • • • • • • • •563 56 nF • • • • • • • • • • •683 68 nF • • • • • • • • • • •823 82 nF • • • • • • • • • • •104 100 nF • • • • • • • • • • •124 120 nF • • • • • • • • • •154 150 nF • • • • • • • • • •184 180 nF • • • • • • • • •224 220 nF • • • • • • • • •274 270 nF • • • • • • • • •334 330 nF • • • • • • • •394 390 nF • • • • • • • •474 470 nF • • • • • • •564 560 nF • • • • • •684 680 nF • • • • • •824 820 nF • • • • • •105 1.0 μF • • • • •125 1.2 μF
Revision: 27-Jan-15 155 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1808 VJ1812 CASE CODE 1808 1812 VOLTAGE (VDC) 25 50 100 200 500 630 1000 1500 2000 3000 25 50 75 100 200 250 500 630 1000 1500 2000 3000VOLTAGE CODE X A B C E L G R F H X A K B C P E L G R F HCAP. CODE CAP.
221 220 pF •271 270 pF • • • • • •471 470 pF • • • • • • • • • •561 560 pF • • • • • • • • • •681 680 pF • • • • • • • • • •821 820 pF • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • • • • • • • • •562 5.6 nF • • • • • • • • • • • • • • • • • • •682 6.8 nF • • • • • • • • • • • • • • • • • • •822 8.2 nF • • • • • • • • • • • • • • • • •103 10 μF • • • • • • • • • • • • • • • • •123 12 μF • • • • • • • • • • • • • • • •153 15 μF • • • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • •393 39 nF • • • • • • • • • • • •473 47 nF • • • • • • • • • • • •563 56 nF • • • • • • • • • • • •683 68 nF • • • • • • • • • • • •823 82 nF • • • • • • • • • • • •104 100 nF • • • • • • • • • • • •124 120 nF • • • • • • • • • •154 150 nF • • • • • • • • •184 180 nF • • • • • • • • •224 220 nF • • • • • • • •274 270 nF • • • • • • • •334 330 nF • • • • • •394 390 nF • • • • •474 470 nF • • • • •564 560 nF • • • •684 680 nF • • • •824 820 nF • • • •105 1.0 μF • •125 1.2 μF155 1.5 μF185 1.8 μF225 2.2 μF275 2.7 μF335 3.3 μF395 3.9 μF475 4.7 μF565 5.6 μF685 6.8 μF825 8.2 μF
Revision: 27-Jan-15 156 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1825 VJ2220CASE CODE 1825 2220VOLTAGE (VDC) 25 50 100 200 500 630 1000 25 50 100 200 500 630 1000 2000 3000VOLTAGE CODE X A B C E L G X A B C E L G F HCAP. CODE CAP.
221 220 pF271 270 pF471 470 pF561 560 pF681 680 pF821 820 pF102 1.0 nF •122 1.2 nF •152 1.5 nF •182 1.8 nF •222 2.2 nF •272 2.7 nF332 3.3 nF392 3.9 nF472 4.7 nF562 5.6 nF •682 6.8 nF •822 8.2 nF •103 10 nF • • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • • • •393 39 nF • • • • • • • • • • • • • •473 47 nF • • • • • • • • • • • • • •563 56 nF • • • • • • • • • • • • • •683 68 nF • • • • • • • • • • • • • •823 82 nF • • • • • • • • • • • • • •104 100 nF • • • • • • • • • • •124 120 nF • • • • • • • • • • •154 150 nF • • • • • • • • • • •184 180 nF • • • • • • • • • • •224 220 nF • • • • • • • • • • •274 270 nF • • • • • • • •334 330 nF • • • • • • • •394 390 nF • • • • • • • •474 470 nF • • • • • • • •564 560 nF • • • • • • • •684 680 nF • • • • • • • •824 820 nF • • • • • • •105 1.0 μF • • • • • • •125 1.2 μF • • • • • •155 1.5 μF • • • • •185 1.8 μF • • • •225 2.2 μF • • •275 2.7 μF •335 3.3 μF395 3.9 μF475 4.7 μF565 5.6 μF685 6.8 μF825 8.2 μF
Revision: 27-Jan-15 157 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC X7RSTYLE VJ2225 VJ3640CASE CODE 2225 3640VOLTAGE (VDC) 25 50 100 200 500 630 1000 1500 2000 25 50 100 200 500VOLTAGE CODE X A B C E L G R F X A B C ECAP. CODE CAP.
102 1.0 nF122 1.2 nF152 1.5 nF182 1.8 nF222 2.2 nF272 2.7 nF332 3.3 nF392 3.9 nF472 4.7 nF562 5.6 nF • •682 6.8 nF • •822 8.2 nF • •103 10 nF • • • • • • • • •123 12 nF • • • • • • • • •153 15 nF • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • • • •393 39 nF • • • • • • • • • • • • • •473 47 nF • • • • • • • • • • • • • •563 56 nF • • • • • • • • • • • •683 68 nF • • • • • • • • • • • •823 82 nF • • • • • • • • • • • •104 100 nF • • • • • • • • • • • •124 120 nF • • • • • • • • • •154 150 nF • • • • • • • • • •184 180 nF • • • • • • • • • •224 220 nF • • • • • • • • • •274 270 nF • • • • • • • • • •334 330 nF • • • • • • • • • •394 390 nF • • • • • • • • •474 470 nF • • • • • • • • •564 560 nF • • • • • • • • •684 680 nF • • • • • • • • •824 820 nF • • • • • • • •105 1.0 μF • • • • • • • •125 1.2 μF • • • • • • • •155 1.5 μF • • • • • • •185 1.8 μF • • • • • • •225 2.2 μF • • • • •275 2.7 μF • • • • •335 3.3 μF • • • •395 3.9 μF • • • •475 4.7 μF • • •565 5.6 μF •685 6.8 μF •825 8.2 μF
Revision: 27-Jan-15 158 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NON-MAGNETIC C0G (NP0) DIELECTRIC - TYPICAL PARAMETERS
- 75 - 50 - 25 0 50 100 125
2.0
1.5
1.0
0.5
0.0
- 0.5
- 1.0
- 1.5
- 2.0
NP0
TEMPERATURE °C 150 175 25 75
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE COEFFICIENT OF CAPACITANCE
TEMPERATURE °C
MIN. INSULATION RESISTANCE VS. TEMPERATURE
10 25 100 125
10 000
1000
100
10
INS
UL
AT
ION
RE
SIS
TAN
CE
(Ω
F)
AGING RATE
HOURS100 1000 10 000
% C
APA
CIT
AN
CE
CH
AN
GE
0.2
0.1
0.0
- 0.1
- 0.2
1 10 0 100 200 300 400 500 600 700 800 900 1000
10
0
- 20
- 30
VOLTAGE COEFFICIENT OF CAPACITANCE
DC VOLTS APPLIED
- 10
20
30%
CA
PAC
ITA
NC
E C
HA
NG
E
CHANGE OF CAPACITANCE WITH FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
2
1
0
- 1
- 2
% C
APA
CIT
AN
CE
CH
AN
GE
DISSIPATION FACTOR VS. FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
0.00025
DIS
SIP
AT
ION
FA
CT
OR
0.0005
0.001
Revision: 27-Jan-15 159 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NON-MAGNETIC X7R DIELECTRIC - TYPICAL PARAMETERS
100
50
TEMPERATURE °C
% R
AT
ED
VO
LT
AG
E
0
RATED VOLTAGE VS. TEMPERATURE
150
200
- 75 - 50 - 25 0 20 50 75 100 125 150 175 10 25 100
10 000
1000
100
10
INS
UL
AT
ION
RE
SIS
TA
NC
E (
ΩF
)
150
MIN. INSULATION RESISTANCE VS. TEMPERATURE
TEMPERATURE °C
HOURS
1.0
0.0
- 1.0
- 2.0
% C
AP
AC
ITA
NC
E C
HA
NG
E
- 3.0
- 4.0
AGING RATE
1 10 100 1000 10 0000.0
TEMPERATURE °C
% D
ISS
IPA
TIO
N F
AC
TO
R
0.51.0
1.5
2.0
2.5
3.0
3.5
4.0
4.55.0
5.5
6.0DISSIPATION FACTOR VS. TEMPERATURE
- 75 - 50 - 25 0 25 50 75 100 125 150 175
X7R
0.020
0.016
0.012
0.008
0.004
DISSIPATION FACTOR VS. VOLTAGE
50 V100 V
DIS
SIP
AT
ION
FA
CT
OR
0 10 20 30 40 50 60 70 80 90 100
DC VOLTS APPLIED UN/V-
DISSIPATION FACTOR VS. VOLTAGE
0 100 200 300 400 500 600 700 UN/V-
0.020
0.016
0.012
0.008
0.004500 V
200 V
DIS
SIP
AT
ION
FA
CT
OR
DC VOLTS APPLIED
Revision: 27-Jan-15 160 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
NON-MAGNETIC X7R DIELECTRIC - TYPICAL PARAMETERS
IMPEDANCE VS. FREQUENCY 500 V/630 V
FREQUENCY (MHz)
0.01 0.1 1 10 100
1000
100
10
1
0.1
0.01
IMP
ED
AN
CE
(Ω
)
1 µF 0.1 µF 0.01 µF
IMPEDANCE VS. FREQUENCY 2000 V
FREQUENCY (MHz)
IMP
ED
AN
CE
(Ω
)
0.1
1000
1 10 100 1000
100
10
1
4.7 nF 2.2 nF 1 nF
0 10 20 30 40 50 60 70 80 90 100
0
- 15
- 20
- 25
- 30
- 10
5
5
25 VRATED
50 V
100 V
VOLTAGE COEFFICIENT OF CAPACITANCE
DC VOLTS APPLIED
% C
APA
CIT
AN
CE
CH
AN
GE
RATED
RATED
DC VOLTS APPLIED
% C
APA
CIT
AN
CE
CH
AN
GE
10
0
- 10
- 20
- 30
- 40
- 50
- 60
- 70
- 80
VOLTAGE COEFFICIENT OF CAPACITANCE LOWER CAPACITANCE
0 100 200 300 400 500 600 700
Case Size1206121018081812
Range100 pF to 4700 pF390 pF to 10 000 pF470 pF to 18 000 pF1000 pF to 27 000 pF
VOLTAGE COEFFICIENT OF CAPACITANCE
DC VOLTS APPLIED
% C
APA
CIT
AN
CE
CH
AN
GE
0 500 1000 1500 2000 2500
10
0
- 10
- 20
- 30
- 40
- 50
- 60
- 70
- 80
1000 V/1500 V RATED2000 V RATED
Revision: 27-Jan-15 161 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for IR Reflow Solderingwww.vishay.com Vishay Vitramon
Notes(1) Vishay Vitramon uses embossed plastic carrier tape(2) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(3) n/a = not available(4) Packaging code “T/R” and lower quantities can depend on product thickness
STANDARD PACKAGING QUANTITIES (1)(2)(3)
CASECODE
TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PAPER TAPE PACKAGING CODE
“C”
PLASTIC TAPE PACKAGING CODE
“T”
LOW QUANTITY PACKAGING CODE
“J”
PAPER TAPE PACKAGING CODE
“P”
PLASTIC TAPE PACKAGING CODE
“R”
0402 8 mm 5000 n/a 1000 10 000 n/a
0603 (4) 8 mm 4000 4000 1000 10 000 10 000
0805 (4) 8 mm 3000 3000 1000 10 000 10 000
1206 (4) 8 mm n/a 3000 / 2500 1000 n/a 10 000 / 9000
1210 8 mm n/a 3000 / 2500 / 2000 1000 n/a 10 000 / 9000
1808 12 mm n/a 2000 500 n/a 10 000
1812 12 mm n/a 1000 500 n/a 4000
1825 12 mm n/a 1000 500 n/a 4000
2220 12 mm n/a 1000 500 n/a 4000
2225 12 mm n/a 1000 500 n/a 4000
3640 16 mm n/a 500 n/a n/a n/a
STORAGE AND HANDLING CONDITIONS
(1) Store the components at +5 °C to +40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 1 year after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt, or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight, and so on.
Revision: 27-Jan-15 162 Document Number: 45227For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitorsfor Non-Magnetic Applications (Epoxy Bonding)
FEATURES• Manufactured with non-magnetic materials• Safety screened for magnetic properties• C0G (NP0) and X7R / X5R dielectrics• Wide range of case sizes, voltage ratings,
and capacitance values• Suitable for conductive epoxy bonding• Wet built process• Reliable Noble Metal Electrode (NME) system • Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS• Magnetic Resonance Imaging (MRI)• Medical test and diagnostic equipment• Hi-rel medical systems• Hi-rel aviation systems• Laboratory analysis systems• Navigation and electronic test equipment• Audio amplifiers
ELECTRICAL SPECIFICATIONS
NON-MAGNETIC C0G (NP0)
GENERAL SPECIFICATIONNoteElectrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range: 1.0 pF to 39 nF
Voltage Range: 10 VDC to 3000 VDC
Temperature Coefficient of Capacitance (TCC):0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
Dissipation Factor (DF):0.1 % maximum at 1.0 VRMS and 1 MHz for values 1000 pF0.1 % maximum at 1.0 VRMS and 1 kHz for values > 1000 pF
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging: 0 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 200 VDC-rated: 250 % of rated voltage500 VDC-rated: 200 % of rated voltage630 VDC, 1000 VDC-rated: 150 % of rated voltage1500 VDC to 3000 VDC-rated: 120 % of rated voltage
NON-MAGNETIC X7R / X5R
GENERAL SPECIFICATIONNoteElectrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range: 100 pF to 6.8 μF
Voltage Range: 6.3 VDC to 3000 VDC
Temperature Coefficient of Capacitance (TCC):X5R: ± 15 % from -55 °C to +85 °C, with 0 VDC appliedX7R: ± 15 % from -55 °C to +125 °C, with 0 VDC applied
Dissipation Factor (DF): 6.3 V, 10 V ratings: 5 % maximum at 1.0 VRMS and 1 kHz16 V, 25 V ratings: 3.5 % maximum at 1.0 VRMS and 1 kHz 50 V ratings: 2.5 % maximum at 1.0 VRMS and 1 kHz
Insulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is less
Aging Rate: 1 % maximum per decade
Dielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 200 VDC-rated: 250 % of rated voltage500 VDC-rated: min. 150 % of rated voltage630 VDC, 1000 VDC-rated: 150 % of rated voltage1500 VDC, 3000 VDC-rated: 120 % of rated voltage
Revision: 08-Oct-14 163 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
QUICK REFERENCE DATA
DIELECTRIC CASEMAXIMUM VOLTAGE
(V)
CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0)
0402 100 1.0 pF 180 pF
0603 200 1.0 pF 1.5 nF
0805 500 1.0 pF 3.3 nF
1206 600 1.0 pF 10 nF
1210 500 1.0 pF 12 nF
1808 3000 10 pF 10 nF
1812 3000 10 pF 22 nF
1825 1000 15 pF 33 nF
2220 1000 100 pF 33 nF
2225 1000 120 pF 39 nF
X5R0402 16 27 nF 47 nF
0603 6.3 120 nF 150 nF
X7R
0402 100 100 pF 22 nF
0603 100 270 pF 100 nF
0805 200 390 pF 390 nF
1206 500 680 pF 1.0 μF
1210 500 1.0 nF 1.0 μF
1808 3000 220 pF 270 nF
1812 3000 270 pF 1.0 μF
1825 1000 10 nF 2.7 μF
2220 3000 1.0 nF 2.2 μF
2225 2000 5.6 nF 4.7 μF
3640 500 15 nF 6.8 μF
Revision: 08-Oct-14 164 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
Notes(1) DC voltage rating should not be exceeded in application (2) Selected values for X5R, see dielectric selection chart
ORDERING INFORMATION VJ0603 Y 102 K N A A O
CASE CODE
DIELECTRIC CAPACITANCE NOMINAL CODE
CAPACITANCE TOLERANCE
TERMINATION DC VOLTAGE RATING (1)
MARKING PACKAGING
04020603080512061210180818121825222022253640
A = C0GY = X7R
G = X5R (2)
Expressed in picofarads (pF).
The first two digits are
significant, the third is a
multiplier. An “R” indicates a
decimal point.Examples
102 = 1000 pF1R0 = 1.0 pF
C0G(NP0):< 10 pF
C = ± 0.25 pF D = 0.5 pF 10 pF
F = ± 1 % G = ± 2 %J = ± 5 %
K = ± 10 %X5R / X7R:J = ± 5 %
K = ± 10 %M = ± 20 %
N = non-magnetic
Q = 10 VJ = 16 VX = 25 VA = 50 VK = 75 V
B = 100 VC = 200 VE = 500 VL = 630 V
G = 1000 VR = 1500 VF = 2000 VH = 3000 V
A = unmarked
T = 7" reel / plastic tapeR = 11 1/4" / 13" reel / plastic tape
O = 7" reel / flamed paper tapeI = 11 1/4" / 13" reel /
flamed paper tapeJ = 7" reel (low quantity)
DIMENSIONS in inches (millimeters)
CASE CODE STYLE LENGTH
(L)WIDTH
(W)
MAXIMUM THICKNESS
(T)
TERMINATIONS(P)
MINIMUM MAXIMUM
0402 VJ0402 0.040 + 0.006 / - 0.004(1.00 + 0.15 / - 0.10)
0.020 ± 0.004(0.50 ± 0.10)
0.024(0.60)
0.004(0.10)
0.016(0.41)
0603 VJ0603 0.063 ± 0.006(1.60 ± 0.15)
0.031 ± 0.006(0.80 ± 0.15)
0.038(0.92)
0.012(0.30)
0.018(0.46)
0805 VJ0805 0.079 ± 0.008(2.00 ± 0.20)
0.049 ± 0.008(1.25 ± 0.20)
0.057(1.45)
0.010(0.25)
0.028(0.71)
1206 VJ1206 0.126 ± 0.010(3.20 ± 0.25)
0.063 ± 0.010(1.60 ± 0.25)
0.067(1.70)
0.010(0.25)
0.028(0.71)
1210 VJ1210 0.126 ± 0.010(3.20 ± 0.25)
0.098 ± 0.010(2.50 ± 0.25)
0.067(1.70)
0.010(0.25)
0.028(0.71)
1808 VJ1808 0.177 ± 0.012(4.50 ± 0.30)
0.080 ± 0.010(2.03 ± 0.25)
0.067(1.70)
0.010(0.25)
0.030(0.76)
1812 VJ1812 0.177 ± 0.012(4.50 ± 0.30)
0.126 ± 0.010(3.20 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
1825 VJ1825 0.177 ± 0.012(4.50 ± 0.30)
0.252 ± 0.010(6.40 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
2220 VJ2220 0.220 ± 0.008(5.59 ± 0.20)
0.200 ± 0.010(5.08 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
2225 VJ2225 0.220 ± 0.010(5.59 ± 0.25)
0.250 ± 0.010(6.35 ± 0.25)
0.086(2.18)
0.010(0.25)
0.030(0.76)
3640 VJ3640 0.360 ± 0.015(9.14 ± 0.38)
0.400 ± 0.015(10.20 ± 0.38)
0.086(2.18)
0.010(0.25)
0.030(0.76)
LW
TMAX.
P
Revision: 08-Oct-14 165 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ0402 VJ0603 VJ0805CASE CODE 0402 0603 0805VOLTAGE (VDC) 10 16 25 50 100 10 16 25 50 100 200 10 16 25 50 100 200 500VOLTAGE CODE Q J X A B Q J X A B C Q J X A B C ECAP. CODE CAP.
1R0 1.0 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •1R2 1.2 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •1R5 1.5 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •1R8 1.8 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •2R2 2.2 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •2R7 2.7 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •3R3 3.3 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •3R9 3.9 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •4R7 4.7 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •5R6 5.6 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •6R8 6.8 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •8R2 8.2 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •100 10 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •120 12 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •150 15 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •180 18 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •220 22 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •270 27 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •330 33 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •390 39 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •470 47 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •560 56 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •680 68 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •820 82 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •101 100 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •121 120 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •151 150 pF •• •• •• •• •• •• •• •• •• •• •• • • • • • • •181 180 pF •• •• •• •• •• •• •• •• •• •• • • • • • • • •221 220 pF •• •• •• •• •• • • • • • • • •271 270 pF •• •• •• •• •• • • • • • • • •331 330 pF •• •• •• •• •• • • • • • • •391 390 pF •• •• •• •• •• • • • • • • •471 470 pF •• •• •• •• • • • • • •561 560 pF •• •• •• •• • • • • • •681 680 pF •• •• •• •• • • • • • •821 820 pF •• •• •• • • • • • •102 1.0 nF •• •• •• • • • • •122 1.2 nF •• •• • • • • •152 1.5 nF •• •• • • • •182 1.8 nF • • • •222 2.2 nF • • • •272 2.7 nF • • •332 3.3 nF • •392 3.9 nF472 4.7 nF562 5.6 nF682 6.8 nF822 8.2 nF103 10 nF123 12 nF
Revision: 08-Oct-14 166 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1206 VJ1210CASE CODE 1206 1210VOLTAGE (VDC) 16 25 50 100 200 500 600 25 50 100 200 500VOLTAGE CODE J X A B C E N X A B C ECAP. CODE CAP.
1R0 1.0 pF • • • • • • • • • • • •1R2 1.2 pF • • • • • • • • • • • •1R5 1.5 pF • • • • • • • • • • • •1R8 1.8 pF • • • • • • • • • • • •2R2 2.2 pF • • • • • • • • • • • •2R7 2.7 pF • • • • • • • • • • • •3R3 3.3 pF • • • • • • • • • • • •3R9 3.9 pF • • • • • • • • • • • •4R7 4.7 pF • • • • • • • • • • • •5R6 5.6 pF • • • • • • • • • • • •6R8 6.8 pF • • • • • • • • • • • •8R2 8.2 pF • • • • • • • • • • • •100 10 pF • • • • • • • • • • • •120 12 pF • • • • • • • • • • • •150 15 pF • • • • • • • • • • • •180 18 pF • • • • • • • • • • • •220 22 pF • • • • • • • • • • • •270 27 pF • • • • • • • • • • • •330 33 pF • • • • • • • • • • • •390 39 pF • • • • • • • • • • • •470 47 pF • • • • • • • • • • • •560 56 pF • • • • • • • • • • • •680 68 pF • • • • • • • • • • • •820 82 pF • • • • • • • • • • • •101 100 pF • • • • • • • • • • • •121 120 pF • • • • • • • • • • • •151 150 pF • • • • • • • • • • • •181 180 pF • • • • • • • • • • • •221 220 pF • • • • • • • • • • • •271 270 pF • • • • • • • • • • • •331 330 pF • • • • • • • • • • • •391 390 pF • • • • • • • • • • • •471 470 pF • • • • • • • • • • • •561 560 pF • • • • • • • • • • • •681 680 pF • • • • • • • • • • • •821 820 pF • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • •122 1.2 nF • • • • • • • • • •152 1.5 nF • • • • • • • • • •182 1.8 nF • • • • • • • • • •222 2.2 nF • • • • • • • • •272 2.7 nF • • • • • • • • •332 3.3 nF • • • • • • • •392 3.9 nF • • • • • • • •472 4.7 nF • • • • • • • •562 5.6 nF • • • • • • •682 6.8 nF • • • • • •822 8.2 nF • • • • •103 10 nF • • • • •123 12 nF • •
Revision: 08-Oct-14 167 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1808 VJ1812CASE CODE 1808 1812VOLTAGE (VDC) 25 50 100 200 500 630 1000 1500 2000 3000 25 50 100 200 500 630 1000 1500 2000 3000VOLTAGE CODE X A B C E L G R F H X A B C E L G R F HCAP. CODE CAP.
100 10 pF • • • • • • • • • •120 12 pF • • • • • • • • • •150 15 pF • • • • • • • • • •180 18 pF • • • • • • • • • •220 22 pF • • • • • • • • • • • • • • •270 27 pF • • • • • • • • • • • • • • •330 33 pF • • • • • • • • • • • • • • •390 39 pF • • • • • • • • • • • • • • •470 47 pF • • • • • • • • • • • • • • • • • • • •560 56 pF • • • • • • • • • • • • • • • • • • • •680 68 pF • • • • • • • • • • • • • • • • • • • •820 82 pF • • • • • • • • • • • • • • • • • • • •101 100 pF • • • • • • • • • • • • • • • • • • • •121 120 pF • • • • • • • • • • • • • • • • • • •151 150 pF • • • • • • • • • • • • • • • • • • •181 180 pF • • • • • • • • • • • • • • • • • • •221 220 pF • • • • • • • • • • • • • • • • • • •271 270 pF • • • • • • • • • • • • • • • • •331 330 pF • • • • • • • • • • • • • • • • •391 390 pF • • • • • • • • • • • • • • • •471 470 pF • • • • • • • • • • • • • • • •561 560 pF • • • • • • • • • • • • • • • •681 680 pF • • • • • • • • • • • • • • • •821 820 pF • • • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • •272 2.7 nF • • • • • • • • •332 3.3 nF • • • • • • • • •392 3.9 nF • • • • • • • • •472 4.7 nF • • • • • • • •562 5.6 nF • • • • • • • •682 6.8 nF • • • • • • • •822 8.2 nF • • • • • • •103 10 nF • • • • • •123 12 nF • • • •153 15 nF • • •183 18 nF • •223 22 nF • •273 27 nF333 33 nF393 39 nF473 47 nF563 56 nF683 68 nF
Revision: 08-Oct-14 168 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1825 VJ2220 VJ2225CASE CODE 1825 2220 2225VOLTAGE (VDC) 25 50 100 200 500 630 1000 25 50 100 200 500 630 1000 25 50 100 200 500 630 1000VOLTAGE CODE X A B C E L G X A B C E L G X A B C E L GCAP. CODE CAP.
100 10 pF120 12 pF150 15 pF • •180 18 pF • •220 22 pF • •270 27 pF • •330 33 pF • •390 39 pF • •470 47 pF • •560 56 pF • •680 68 pF • •820 82 pF • •101 100 pF • • • • • • • • • • • •121 120 pF • • • • • • • • • • • • • • • • •151 150 pF • • • • • • • • • • • • • • • • •181 180 pF • • • • • • • • • • • • • • • • •221 220 pF • • • • • • • • • • • • • • • • •271 270 pF • • • • • • • • • • • • • • • • • • • • •331 330 pF • • • • • • • • • • • • • • • • • • • • •391 390 pF • • • • • • • • • • • • • • • • • • • • •471 470 pF • • • • • • • • • • • • • • • • • • • • •561 560 pF • • • • • • • • • • • • • • • • • • • • •681 680 pF • • • • • • • • • • • • • • • • • • • • •821 820 pF • • • • • • • • • • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • • • • • • • • •562 5.6 nF • • • • • • • • • • • • • • •682 6.8 nF • • • • • • • • • • • • • •822 8.2 nF • • • • • • • • • • • • • •103 10 nF • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • •183 18 nF • • • • • • • • • • •223 22 nF • • • • • • • • • • •273 27 nF • • • • • • • • • • •333 33 nF • • • • • • • • • • •393 39 nF • • • •473 47 nF563 56 nF683 68 nF
Revision: 08-Oct-14 169 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape(1) See selection chart for values only available as X5R. All other values X7R.
SELECTION CHARTDIELECTRIC X7R / X5R (1)
STYLE VJ0402 VJ0603 VJ0805CASE CODE 0402 0603 0805VOLTAGE (VDC) 6.3 10 16 25 50 100 6.3 10 16 25 50 100 10 16 25 50 100 200VOLTAGE CODE Y Q J X A B Y Q J X A B Q J X A B CCAP. CODE CAP.
101 100 pF •• •• •• •• •• ••121 120 pF •• •• •• •• •• ••151 150 pF •• •• •• •• •• ••181 180 pF •• •• •• •• •• ••221 220 pF •• •• •• •• •• ••271 270 pF •• •• •• •• •• •• •• •• •• •• •• ••331 330 pF •• •• •• •• •• •• •• •• •• •• •• ••391 390 pF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •471 470 pF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •561 560 pF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •681 680 pF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •821 820 pF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •102 1.0 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •122 1.2 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •152 1.5 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •182 1.8 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •222 2.2 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •272 2.7 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •332 3.3 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •392 3.9 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •472 4.7 nF •• •• •• •• •• •• •• •• •• •• •• •• • • • • • •562 5.6 nF •• •• •• •• •• •• •• •• •• •• •• • • • • • •682 6.8 nF •• •• •• •• •• •• •• •• •• •• •• • • • • • •822 8.2 nF •• •• •• •• •• •• •• •• •• •• •• • • • • • •103 10 nF •• •• •• •• •• •• •• •• •• •• •• • • • • • •123 12 nF •• •• •• •• •• •• •• •• •• •• • • • • • •153 15 nF •• •• •• •• •• •• •• •• •• •• • • • • • •183 18 nF •• •• •• •• •• •• •• •• •• • • • • • •223 22 nF •• •• •• •• •• •• •• •• •• • • • • • •273 27 nF X5R •• X5R •• X5R •• •• •• •• •• •• • • • • • •333 33 nF X5R •• X5R •• X5R •• •• •• •• •• •• • • • • •393 39 nF X5R •• •• •• •• •• •• • • • • •473 47 nF X5R •• •• •• •• •• •• • • • • •563 56 nF •• •• •• •• • • • • •683 68 nF •• •• •• •• • • • • •823 82 nF •• •• •• •• • • • • •104 100 nF •• •• •• •• • • • •124 120 nF X5R •• • • • •154 150 nF X5R •• • • • •184 180 nF • • •224 220 nF • • •274 270 nF • • •334 330 nF • • •394 390 nF •474 470 nF564 560 nF684 680 nF824 820 nF105 1.0 μF125 1.2 μF
Revision: 08-Oct-14 170 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1206 VJ1210CASE CODE 1206 1210VOLTAGE (VDC) 16 25 50 100 200 500 16 25 50 75 100 200 500VOLTAGE CODE J X A B C E J X A K B C ECAP. CODE CAP.
101 100 pF121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF331 330 pF391 390 pF471 470 pF561 560 pF681 680 pF • • • • • •821 820 pF • • • • • •102 1.0 nF • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • • •562 5.6 nF • • • • • • • • • • • • •682 6.8 nF • • • • • • • • • • • • •822 8.2 nF • • • • • • • • • • • • •103 10 nF • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • •273 27 nF • • • • • • • • • • • •333 33 nF • • • • • • • • • • • •393 39 nF • • • • • • • • • • • •473 47 nF • • • • • • • • • • • •563 56 nF • • • • • • • • • • •683 68 nF • • • • • • • • • • •823 82 nF • • • • • • • • • • •104 100 nF • • • • • • • • • • •124 120 nF • • • • • • • • • •154 150 nF • • • • • • • • • •184 180 nF • • • • • • • • •224 220 nF • • • • • • • • •274 270 nF • • • • • • • • •334 330 nF • • • • • • • •394 390 nF • • • • • • • •474 470 nF • • • • • • •564 560 nF • • • • • •684 680 nF • • • • • •824 820 nF • • • • • •105 1.0 μF • • • • •125 1.2 μF
Revision: 08-Oct-14 171 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1808 VJ1812 CASE CODE 1808 1812 VOLTAGE (VDC) 25 50 100 200 500 630 1000 1500 2000 3000 25 50 75 100 200 250 500 630 1000 1500 2000 3000VOLTAGE CODE X A B C E L G R F H X A K B C P E L G R F HCAP. CODE CAP.
221 220 pF •271 270 pF • • • • • •471 470 pF • • • • • • • • • •561 560 pF • • • • • • • • • •681 680 pF • • • • • • • • • •821 820 pF • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • • • • • • • • •562 5.6 nF • • • • • • • • • • • • • • • • • • •682 6.8 nF • • • • • • • • • • • • • • • • • • •822 8.2 nF • • • • • • • • • • • • • • • • •103 10 μF • • • • • • • • • • • • • • • • •123 12 μF • • • • • • • • • • • • • • • •153 15 μF • • • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • •393 39 nF • • • • • • • • • • • •473 47 nF • • • • • • • • • • • •563 56 nF • • • • • • • • • • • •683 68 nF • • • • • • • • • • • •823 82 nF • • • • • • • • • • • •104 100 nF • • • • • • • • • • • •124 120 nF • • • • • • • • • •154 150 nF • • • • • • • • •184 180 nF • • • • • • • • •224 220 nF • • • • • • • •274 270 nF • • • • • • • •334 330 nF • • • • • •394 390 nF • • • • •474 470 nF • • • • •564 560 nF • • • •684 680 nF • • • •824 820 nF • • • •105 1.0 μF • •125 1.2 μF155 1.5 μF185 1.8 μF225 2.2 μF275 2.7 μF335 3.3 μF395 3.9 μF475 4.7 μF565 5.6 μF685 6.8 μF825 8.2 μF
Revision: 08-Oct-14 172 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1825 VJ2220CASE CODE 1825 2220VOLTAGE (VDC) 25 50 100 200 500 630 1000 25 50 100 200 500 630 1000 2000 3000VOLTAGE CODE X A B C E L G X A B C E L G F HCAP. CODE CAP.
221 220 pF271 270 pF471 470 pF561 560 pF681 680 pF821 820 pF102 1.0 nF •122 1.2 nF •152 1.5 nF •182 1.8 nF •222 2.2 nF •272 2.7 nF332 3.3 nF392 3.9 nF472 4.7 nF562 5.6 nF •682 6.8 nF •822 8.2 nF •103 10 nF • • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • • • •393 39 nF • • • • • • • • • • • • • •473 47 nF • • • • • • • • • • • • • •563 56 nF • • • • • • • • • • • • • •683 68 nF • • • • • • • • • • • • • •823 82 nF • • • • • • • • • • • • • •104 100 nF • • • • • • • • • • •124 120 nF • • • • • • • • • • •154 150 nF • • • • • • • • • • •184 180 nF • • • • • • • • • • •224 220 nF • • • • • • • • • • •274 270 nF • • • • • • • •334 330 nF • • • • • • • •394 390 nF • • • • • • • •474 470 nF • • • • • • • •564 560 nF • • • • • • • •684 680 nF • • • • • • • •824 820 nF • • • • • • •105 1.0 μF • • • • • • •125 1.2 μF • • • • • •155 1.5 μF • • • • •185 1.8 μF • • • •225 2.2 μF • • •275 2.7 μF •335 3.3 μF395 3.9 μF475 4.7 μF565 5.6 μF685 6.8 μF825 8.2 μF
Revision: 08-Oct-14 173 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NotesRoHS-compliant
•• Flamed paper tape • Plastic tape
SELECTION CHARTDIELECTRIC X7RSTYLE VJ2225 VJ3640CASE CODE 2225 3640VOLTAGE (VDC) 25 50 100 200 500 630 1000 1500 2000 25 50 100 200 500VOLTAGE CODE X A B C E L G R F X A B C ECAP. CODE CAP.
102 1.0 nF122 1.2 nF152 1.5 nF182 1.8 nF222 2.2 nF272 2.7 nF332 3.3 nF392 3.9 nF472 4.7 nF562 5.6 nF • •682 6.8 nF • •822 8.2 nF • •103 10 nF • • • • • • • • •123 12 nF • • • • • • • • •153 15 nF • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • • • •393 39 nF • • • • • • • • • • • • • •473 47 nF • • • • • • • • • • • • • •563 56 nF • • • • • • • • • • • •683 68 nF • • • • • • • • • • • •823 82 nF • • • • • • • • • • • •104 100 nF • • • • • • • • • • • •124 120 nF • • • • • • • • • •154 150 nF • • • • • • • • • •184 180 nF • • • • • • • • • •224 220 nF • • • • • • • • • •274 270 nF • • • • • • • • • •334 330 nF • • • • • • • • • •394 390 nF • • • • • • • • •474 470 nF • • • • • • • • •564 560 nF • • • • • • • • •684 680 nF • • • • • • • • •824 820 nF • • • • • • • •105 1.0 μF • • • • • • • •125 1.2 μF • • • • • • • •155 1.5 μF • • • • • • •185 1.8 μF • • • • • • •225 2.2 μF • • • • •275 2.7 μF • • • • •335 3.3 μF • • • •395 3.9 μF • • • •475 4.7 μF • • •565 5.6 μF •685 6.8 μF •825 8.2 μF
Revision: 08-Oct-14 174 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NON-MAGNETIC C0G (NP0) DIELECTRIC - TYPICAL PARAMETERS
-75 -50 -25 0 50 100 125
2.0
1.5
1.0
0.5
0.0
-0.5
-1.0
-1.5
-2.0
NP0
TEMPERATURE °C 150 175 25 75
% C
APA
CIT
AN
CE
CH
AN
GE
TEMPERATURE COEFFICIENT OF CAPACITANCE
TEMPERATURE °C
MIN. INSULATION RESISTANCE VS. TEMPERATURE
10 25 100 125
10 000
1000
100
10
INS
UL
AT
ION
RE
SIS
TAN
CE
(Ω
F)
AGING RATE
HOURS100 1000 10 000
% C
APA
CIT
AN
CE
CH
AN
GE
0.2
0.1
0.0
-0.1
-0.2
1 10 0 100 200 300 400 500 600 700 800 900 1000
10
0
-20
-30
VOLTAGE COEFFICIENT OF CAPACITANCE
DC VOLTS APPLIED
-10
20
30%
CA
PAC
ITA
NC
E C
HA
NG
E
CHANGE OF CAPACITANCE WITH FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
2
1
0
-1
-2
% C
APA
CIT
AN
CE
CH
AN
GE
DISSIPATION FACTOR VS. FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
0.00025
DIS
SIP
AT
ION
FA
CT
OR
0.0005
0.001
Revision: 08-Oct-14 175 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NON-MAGNETIC X7R DIELECTRIC - TYPICAL PARAMETERS
100
50
TEMPERATURE °C
% R
AT
ED
VO
LT
AG
E
0-75 -50 -25 0 20 50 75 100 125 150 175
RATED VOLTAGE VS. TEMPERATURE
150
200
10 25 100
10 000
1000
100
10
INS
UL
AT
ION
RE
SIS
TA
NC
E (
ΩF
)
150
MIN. INSULATION RESISTANCE VS. TEMPERATURE
TEMPERATURE °C
HOURS
1.0
0.0
-1.0
-2.0
% C
AP
AC
ITA
NC
E C
HA
NG
E
-3.0
-4.0
AGING RATE
1 10 100 1000 10 0000.0
TEMPERATURE °C
% D
ISS
IPA
TIO
N F
AC
TO
R
0.51.0
1.5
2.0
2.5
3.0
3.5
4.0
4.55.0
5.5
6.0DISSIPATION FACTOR VS. TEMPERATURE
X7R
-75 -50 -25 0 20 50 75 100 125 150 175
0.020
0.016
0.012
0.008
0.004
DISSIPATION FACTOR VS. VOLTAGE
50 V100 V
DIS
SIP
AT
ION
FA
CT
OR
0 10 20 30 40 50 60 70 80 90 100
DC VOLTS APPLIED UN/V-
DISSIPATION FACTOR VS. VOLTAGE
0 100 200 300 400 500 600 700 UN/V-
0.020
0.016
0.012
0.008
0.004500 V
200 V
DIS
SIP
AT
ION
FA
CT
OR
DC VOLTS APPLIED
Revision: 08-Oct-14 176 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
NON-MAGNETIC X7R DIELECTRIC - TYPICAL PARAMETERS
IMPEDANCE VS. FREQUENCY 500 V/630 V
FREQUENCY (MHz)
0.01 0.1 1 10 100
1000
100
10
1
0.1
0.01
IMP
ED
AN
CE
(Ω
)
1 µF 0.1 µF 0.01 µF
IMPEDANCE VS. FREQUENCY 2000 V
FREQUENCY (MHz)
IMP
ED
AN
CE
(Ω
)
0.1
1000
1 10 100 1000
100
10
1
4.7 nF 2.2 nF 1 nF
0 10 20 30 40 50 60 70 80 90 100
0
-15
-20
-25
-30
-10
5
5
25 VRATED
50 V
100 V
VOLTAGE COEFFICIENT OF CAPACITANCE
DC VOLTS APPLIED
% C
APA
CIT
AN
CE
CH
AN
GE
RATED
RATED
DC VOLTS APPLIED
% C
APA
CIT
AN
CE
CH
AN
GE
10
0
-10
-20
-30
-40
-50
-60
-70
-80
VOLTAGE COEFFICIENT OF CAPACITANCE LOWER CAPACITANCE
0 100 200 300 400 500 600 700
Case Size1206121018081812
Range100 pF to 4700 pF390 pF to 10 000 pF470 pF to 18 000 pF1000 pF to 27 000 pF
VOLTAGE COEFFICIENT OF CAPACITANCE
DC VOLTS APPLIED
% C
APA
CIT
AN
CE
CH
AN
GE
0 500 1000 1500 2000 2500
10
0
-10
-20
-30
-40
-50
-60
-70
-80
1000 V/1500 V RATED2000 V RATED
Revision: 08-Oct-14 177 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Non-Magnetic Series for Epoxy Bondingwww.vishay.com Vishay Vitramon
Notes(1) Vishay Vitramon uses embossed plastic carrier tape(2) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(3) n/a = not available(4) Packaging code “O/I” or “T/R” and lower quantities can depend on product thickness
STANDARD PACKAGING QUANTITIES (1)(2)(3)
CASECODE
TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PAPER TAPE PACKAGING CODE
“O”
PLASTIC TAPE PACKAGING CODE
“T”
LOW QUANTITY PACKAGING CODE
“J”
PAPER TAPE PACKAGING CODE
“I”
PLASTIC TAPE PACKAGING CODE
“R”
0402 8 mm 5000 n/a 1000 10 000 n/a
0603 (4) 8 mm 4000 4000 1000 10 000 10 000
0805 (4) 8 mm 3000 3000 1000 10 000 10 000
1206 (4) 8 mm n/a 3000 / 2500 1000 n/a 10 000 / 9000
1210 (4) 8 mm n/a 3000 / 2500 / 2000 1000 n/a 10 000 / 9000
1808 12 mm n/a 2000 500 n/a 10 000
1812 12 mm n/a 1000 500 n/a 4000
1825 12 mm n/a 1000 500 n/a 4000
2220 12 mm n/a 1000 500 n/a 4000
2225 12 mm n/a 1000 500 n/a 4000
3640 16 mm n/a 500 n/a n/a n/a
STORAGE AND HANDLING CONDITIONS
(1) Store the components at +5 °C to +40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt, or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight, and so on.
Revision: 08-Oct-14 178 Document Number: 45128For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Contents
VJ Hi-Rel Series ..................... 180
CDR-MIL-PRF-55681 ............ 194
DSCC 03029 .......................... 205
DSCC 03028 .......................... 209
DSCC 05006 .......................... 214
DSCC 05007 .......................... 218
DSCC 05001 .......................... 222
DSCC 05002 .......................... 226
DSCC 05003 .......................... 230
MLCCsfor
High Reliability and
Military / Aerospace
Applications
(NME Technology)
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitorsfor High Reliability Applications
FEATURES• Manufactured with a combination of design,
materials and tight process control toachieve very high field reliability
• C0G (NP0) and X7R/X5R dieectrics offered• MIL-PRF-55681 qualified production line • Reliability maintenance testing to verify
consistent quality(X5R max. test temperature: +85 °C)
• Available with group A and C screening• Group C data can be reported• Available with only group A screening• Available with only voltage conditioning• Customized certification available on request to meet your
quality requirements• Available with tin-lead barrier terminations order code “L”• Wet build process• Reliable Noble Metal Electrode (NME) system • Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912 Note* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information / tables in this datasheet for details.
APPLICATIONS• System critical medical applications• Mission critical military and aerospace applications
ELECTRICAL SPECIFICATIONS
Available
Available
C0G (NP0)
GENERAL SPECIFICATIONNote Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C Capacitance Range: 1.0 pF to 39 nFVoltage Range: 10 VDC to 600 VDC
Temperature Coefficient of Capacitance (TCC):0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °CDissipation Factor (DF):0.1 % maximum at 1.0 VRMS and 1 MHz for values 1000 pF0.1 % maximum at 1.0 VRMS and 1 kHz for values > 1000 pFInsulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is lessAging Rate: 0 % maximum per decadeDielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 200 VDC-rated: 250 % of rated voltage500 VDC-rated: 200 % of rated voltage630 VDC-rated: 150 % of rated voltage
X7R/X5R
GENERAL SPECIFICATIONNoteElectrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C Capacitance Range: 100 pF to 6.8 μFVoltage Range: 6.3 VDC to 500 VDC
Temperature Coefficient of Capacitance (TCC):X5R: ± 15 % from -55 °C to +85 °C, with 0 VDC appliedX7R: ± 15 % from -55 °C to +125 °C, with 0 VDC appliedDissipation Factor (DF): 6.3 V, 10 V ratings: 5 % maximum at 1.0 VRMS and 1 kHz16 V, 25 V ratings: 3.5 % maximum at 1.0 VRMS and 1 kHz 50 V ratings: 2.5 % maximum at 1.0 VRMS and 1 kHzInsulating Resistance:at +25 °C 100 000 M min. or 1000 F whichever is lessat +125 °C 10 000 M min. or 100 F whichever is lessAging Rate: 1 % maximum per decadeDielectric Strength Test:performed per method 103 of EIA 198-2-E.Applied test voltages 250 VDC-rated: 250 % of rated voltage500 VDC-rated: min. 150 % of rated voltage630 VDC, 1000 VDC-rated: 150 % of rated voltage1500 VDC, 3000 VDC-rated: 120 % of rated voltage
Revision: 17-Feb-15 180 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
Notes(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questons: [email protected](2) Process code has to be added(3) Process code “2L” group “C” completion not required for shipment(4) Process code “2M” group “C” completion required for shipment(5) Process code “2MP” group “C” will be completed and data included with shipment
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE(V)
CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0)
0402 100 1.0 pF 180 pF0603 200 1.0 pF 1.5 nF0805 500 1.0 pF 3.3 nF1206 600 1.0 pF 10 nF1210 500 1.0 pF 10 nF1808 500 22 pF 10 nF1812 500 39 pF 22 nF1825 500 100 pF 33 nF2220 500 100 pF 33 nF2225 500 120 pF 39 nF
X5R0402 16 27 nF 47 nF0603 6.3 120 nF 150 nF
X7R
0402 100 100 pF 22 nF0603 100 270 pF 100 nF0805 200 150 pF 390 nF1206 500 680 pF 1.0 μF1210 500 1.0 nF 1.0 μF1808 500 1.0 nF 270 nF1812 500 3.3 nF 1.0 μF1825 500 10 nF 2.7 μF2220 500 10 nF 2.2 μF2225 500 10 nF 4.7 μF3640 500 15 nF 6.8 μF
ORDERING INFORMATIONVJ1206 Y 104 J L A A T ### (2)
CASE CODE
DIELECTRIC CAPACITANCE NOMINAL
CAPACITANCE TOLERANCE
TERMINATION DC VOLTAGE RATING (1)
MARKING PACKAGING PROCESS CODE
0402 0603 0805 1206 121018081812 1825 2220 2225 3640
A = C0G (NP0)G = X5R Y = X7R
Expressed in picofarads (pF).
The first two digits are
significant, the third is a multiplier.
Examples:1R0 = 1.0 pF
103 = 10 000 pF
104 = 100 000 pF
C = ± 0.25 pFD = ± 0.50 pF
F = ± 1 %G = ± 2 %H = ± 3 %J = ± 5 %
K = ± 10 %M = ± 20 %
Note:C0G (NP0):
C, D < 10 pFF, G, H, J ,K 10 pF
X7R, X5R:J, K, M
X = Ni barrier 100 % tin plated
L = Ni barrier with tin lead plated
finishmin. 4 % lead
F = AgPdN =
non-magnetic
Y = 6.3 VQ = 10 VJ = 16 VX = 25 V A = 50 VK = 75 V
B = 100 VC = 200 VP = 250 VE = 500 VN = 600 V
A = unmarked
C = 7" reel/paper tape
T = 7" reel/plastic tape
J = 7" reel (low quantity)
P = 11 1/4"/13" reel/paper tapeR = 11 1/4"/13" reel/plastic tape
O = 7" reel/flamed paper tape
I = 11 1/4"/13"reel/flamed paper tape
Note:“I” and “O” are
used for “F”, “N” terminations, sizes 0402/0603/0805
2L, 2M,2MP = high rel
group A and C
screening
(3)(4)(5)
68 = high rel group A
screening only
5G = voltage conditioning
only
Revision: 17-Feb-15 181 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
Note• Termination code “F” has increased dimension tolerance:
0402: length + 0.006" (+ 0.15 mm)0603: length + 0.008" (+ 0.20 mm)0805/1206/1210: length + 0.011" (+ 0.28 mm)
DIMENSIONS in inches (millimeters)
CASE CODE STYLE LENGTH(L)
WIDTH (W)
MAXIMUMTHICKNESS
(T)
TERMINATION PAD(P)
MINIMUM MAXIMUM
0402 VJ04020.040 ± 0.004(1.00 ± 0.10)
0.020 ± 0.004(0.50 ± 0.10)
0.024 (0.61) 0.004 (0.10) 0.016 (0.41)
0603 VJ06030.063 ± 0.006(1.60 ± 0.15)
0.031 ± 0.006(0.80 ± 0.15)
0.036 (0.92) 0.012 (0.30) 0.018 (0.46)
0805 VJ08050.079 ± 0.008(2.00 ± 0.20)
0.049 ± 0.008(1.25 ± 0.20)
0.057 (1.45) 0.010 (0.25) 0.028 (0.71)
1206 VJ12060.126 ± 0.010(3.20 ± 0.25)
0.063 ± 0.010(1.60 ± 0.25)
0.067 (1.70) 0.010 (0.25) 0.028 (0.71)
1210 VJ12100.126 ± 0.010(3.20 ± 0.25)
0.098 ± 0.010(2.50 ± 0.25)
0.067 (1.70) 0.010 (0.25) 0.028 (0.71)
1808 VJ18080.180 ± 0.012(4.57 ± 0.30)
0.080 ± 0.010(2.03 ± 0.25)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
1812 VJ18120.177 ± 0.012(4.50 ± 0.30)
0.126 ± 0.008(3.20 ± 0.20)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
1825 VJ18250.177 ± 0.012(4.50 ± 0.30)
0.252 ± 0.010(6.40 ± 0.25)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
2220 VJ22200.220 ± 0.010(5.59 ± 0.25)
0.200 ± 0.010(5.08 ± 0.25)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
2225 VJ22250.220 ± 0.010(5.59 ± 0.25)
0.250 ± 0.010(6.35 ± 0.25)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
3640 VJ36400.360 ± 0.015(9.14 ± 0.38)
0.400 ± 0.015(10.2 ± 0.38)
0.086 (2.18) 0.010 (0.25) 0.030 (0.76)
L W
TMAX.
P
Revision: 17-Feb-15 182 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”Not RoHS-compliant
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ0402 VJ0603 VJ0805CASE CODE 0402 0603 0805VOLTAGE (VDC) 10 16 25 50 100 10 16 25 50 100 200 10 16 25 50 100 200 500VOLTAGE CODE Q J X A B Q J X A B C Q J X A B C ECAP. CODE CAP.
1R0 1.0 pF • • • • • • • • • • • • • • • • • •1R2 1.2 pF • • • • • • • • • • • • • • • • • •1R5 1.5 pF • • • • • • • • • • • • • • • • • •1R8 1.8 pF • • • • • • • • • • • • • • • • • •2R2 2.2 pF • • • • • • • • • • • • • • • • • •2R7 2.7 pF • • • • • • • • • • • • • • • • • •3R3 3.3 pF • • • • • • • • • • • • • • • • • •3R9 3.9 pF • • • • • • • • • • • • • • • • • •4R7 4.7 pF • • • • • • • • • • • • • • • • • •5R6 5.6 pF • • • • • • • • • • • • • • • • • •6R8 6.8 pF • • • • • • • • • • • • • • • • • •8R2 8.2 pF • • • • • • • • • • • • • • • • • •100 10 pF • • • • • • • • • • • • • • • • • •120 12 pF • • • • • • • • • • • • • • • • • •150 15 pF • • • • • • • • • • • • • • • • • •180 18 pF • • • • • • • • • • • • • • • • • •220 22 pF • • • • • • • • • • • • • • • • • •270 27 pF • • • • • • • • • • • • • • • • • •330 33 pF • • • • • • • • • • • • • • • • • •390 39 pF • • • • • • • • • • • • • • • • • •470 47 pF • • • • • • • • • • • • • • • • • •560 56 pF • • • • • • • • • • • • • • • • • •680 68 pF • • • • • • • • • • • • • • • • • •820 82 pF • • • • • • • • • • • • • • • • • •101 100 pF • • • • • • • • • • • • • • • • • •121 120 pF • • • • • • • • • • • • • • • • • •151 150 pF • • • • • • • • • • • • • • • • •181 180 pF • • • • • • • • • • • • • • • • •221 220 pF • • • • • • • • • • • • •271 270 pF • • • • • • • • • • • • •331 330 pF • • • • • • • • • • • •391 390 pF • • • • • • • • • • • •471 470 pF • • • • • • • • • •561 560 pF • • • • • • • • • •681 680 pF • • • • • • • • • •821 820 pF • • • • • • • • •102 1.0 nF • • • • • • • •122 1.2 nF • • • • • • •152 1.5 nF • • • • • • •182 1.8 nF • • • •222 2.2 nF • • • •272 2.7 nF • • •282 2.8 nF • • •332 3.3 nF • •392 3.9 nF472 4.7 nF562 5.6 nF682 6.8 nF822 8.2 nF103 10 nF123 12 nF
Revision: 17-Feb-15 183 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
Notes(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
RoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”Not RoHS-compliant
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1206 VJ1210 (1)
CASE CODE 1206 1210 (1)
VOLTAGE (VDC) 16 25 50 100 200 500 600 25 50 100 200 500VOLTAGE CODE J X A B C E N X A B C ECAP. CODE CAP.
1R0 1.0 pF • • • • • • • • • • • •1R2 1.2 pF • • • • • • • • • • • •1R5 1.5 pF • • • • • • • • • • • •1R8 1.8 pF • • • • • • • • • • • •2R2 2.2 pF • • • • • • • • • • • •2R7 2.7 pF • • • • • • • • • • • •3R3 3.3 pF • • • • • • • • • • • •3R9 3.9 pF • • • • • • • • • • • •4R7 4.7 pF • • • • • • • • • • • •5R6 5.6 pF • • • • • • • • • • • •6R8 6.8 pF • • • • • • • • • • • •8R2 8.2 pF • • • • • • • • • • • •100 10 pF • • • • • • • • • • • •120 12 pF • • • • • • • • • • • •150 15 pF • • • • • • • • • • • •180 18 pF • • • • • • • • • • • •220 22 pF • • • • • • • • • • • •270 27 pF • • • • • • • • • • • •330 33 pF • • • • • • • • • • • •390 39 pF • • • • • • • • • • • •470 47 pF • • • • • • • • • • • •560 56 pF • • • • • • • • • • • •680 68 pF • • • • • • • • • • • •820 82 pF • • • • • • • • • • • •101 100 pF • • • • • • • • • • • •121 120 pF • • • • • • • • • • • •151 150 pF • • • • • • • • • • • •181 180 pF • • • • • • • • • • • •221 220 pF • • • • • • • • • • • •271 270 pF • • • • • • • • • • • •331 330 pF • • • • • • • • • • • •391 390 pF • • • • • • • • • • • •471 470 pF • • • • • • • • • • • •561 560 pF • • • • • • • • • • • •681 680 pF • • • • • • • • • • • •821 820 pF • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • •122 1.2 nF • • • • • • • • • •152 1.5 nF • • • • • • • • • •182 1.8 nF • • • • • • • • • •222 2.2 nF • • • • • • • • •272 2.7 nF • • • • • • • • •282 2.8 nF • • • • • • • •332 3.3 nF • • • • • • • •392 3.9 nF • • • • • • • •472 4.7 nF • • • • • • • •562 5.6 nF • • • • • • •682 6.8 nF • • • • • •822 8.2 nF • • •103 10 nF • • •123 12 nF
Revision: 17-Feb-15 184 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
Notes(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
RoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”Not RoHS-compliant
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ1808 (1) VJ1812 (1) VJ1825 (1)
CASE CODE 1808 (1) 1812 (1) 1825 (1)
VOLTAGE (VDC) 25 50 100 200 500 25 50 100 200 500 25 50 100 200 500VOLTAGE CODE X A B C E X A B C E X A B C ECAP. CODE CAP.
100 10 pF120 12 pF150 15 pF180 18 pF220 22 pF • • • • •270 27 pF • • • • •330 33 pF • • • • •390 39 pF • • • • • • • •470 47 pF • • • • • • • • • •560 56 pF • • • • • • • • • •680 68 pF • • • • • • • • • •820 82 pF • • • • • • • • • •101 100 pF • • • • • • • • • • • • • • •121 120 pF • • • • • • • • • • • • • • •151 150 pF • • • • • • • • • • • • • • •181 180 pF • • • • • • • • • • • • • • •221 220 pF • • • • • • • • • • • • • • •271 270 pF • • • • • • • • • • • • • • •331 330 pF • • • • • • • • • • • • • • •391 390 pF • • • • • • • • • • • • • • •471 470 pF • • • • • • • • • • • • • • •561 560 pF • • • • • • • • • • • • • • •681 680 pF • • • • • • • • • • • • • • •821 820 pF • • • • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • • • •562 5.6 nF • • • • • • • • • • • • •682 6.8 nF • • • • • • • • • • • • •822 8.2 nF • • • • • • • • • • • •103 10 nF • • • • • • • • • • •123 12 nF • • • • • • • •153 15 nF • • • • • • •183 18 nF • • • • • •223 22 nF • • • • • •273 27 nF • • • •333 33 nF • • •393 39 nF473 47 nF563 56 nF683 68 nF
Revision: 17-Feb-15 185 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
Notes(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
RoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”Not RoHS-compliant
SELECTION CHARTDIELECTRIC C0G (NP0)STYLE VJ2220 (1) VJ2225 (1)
CASE CODE 2220 (1) 2225 (1)
VOLTAGE (VDC) 25 50 100 200 500 25 50 100 200 500VOLTAGE CODE X A B C E X A B C ECAP. CODE CAP.
100 10 pF120 12 pF150 15 pF180 18 pF220 22 pF270 27 pF330 33 pF390 39 pF470 47 pF560 56 pF680 68 pF820 82 pF101 100 pF • • • • •121 120 pF • • • • • • • • • •151 150 pF • • • • • • • • • •181 180 pF • • • • • • • • • •221 220 pF • • • • • • • • • •271 270 pF • • • • • • • • • •331 330 pF • • • • • • • • • •391 390 pF • • • • • • • • • •471 470 pF • • • • • • • • • •561 560 pF • • • • • • • • • •681 680 pF • • • • • • • • • •821 820 pF • • • • • • • • • •102 1.0 nF • • • • • • • • • •122 1.2 nF • • • • • • • • • •152 1.5 nF • • • • • • • • • •182 1.8 nF • • • • • • • • • •222 2.2 nF • • • • • • • • • •272 2.7 nF • • • • • • • • • •332 3.3 nF • • • • • • • • • •392 3.9 nF • • • • • • • • • •472 4.7 nF • • • • • • • • • •562 5.6 nF • • • • • • • • • •682 6.8 nF • • • • • • • • •822 8.2 nF • • • • • • • • •103 10 nF • • • • • • • • •123 12 nF • • • • • • • • •153 15 nF • • • • • • • •183 18 nF • • • • • • •223 22 nF • • • • • • •273 27 nF • • • • • • •333 33 nF • • • • • • •393 39 nF • • • •473 47 nF563 56 nF683 68 nF
Revision: 17-Feb-15 186 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
Notes(1) See “Selection Chart” for values only available as X5R. All other values X7R.
RoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”Not RoHS-compliant
SELECTION CHARTDIELECTRIC X7R/X5R (1)
STYLE VJ0402 VJ0603 VJ0805CASE CODE 0402 0603 0805VOLTAGE (VDC) 6.3 10 16 25 50 100 6.3 10 16 25 50 100 10 16 25 50 100 200VOLTAGE CODE Y Q J X A B Y Q J X A B Q J X A B C
CAP. CODE CAP.101 100 pF • • • • • •121 120 pF • • • • • •151 150 pF • • • • • • • • • • • •181 180 pF • • • • • • • • • • • •221 220 pF • • • • • • • • • • • •271 270 pF • • • • • • • • • • • • • • • • • •331 330 pF • • • • • • • • • • • • • • • • • •391 390 pF • • • • • • • • • • • • • • • • • •471 470 pF • • • • • • • • • • • • • • • • • •561 560 pF • • • • • • • • • • • • • • • • • •681 680 pF • • • • • • • • • • • • • • • • • •821 820 pF • • • • • • • • • • • • • • • • • •102 1.0 nF • • • • • • • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • • • • • • •562 5.6 nF • • • • • • • • • • • • • • • • •682 6.8 nF • • • • • • • • • • • • • • • • •822 8.2 nF • • • • • • • • • • • • • • • • •103 10 nF • • • • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • • •273 27 nF X5R X5R X5R • • • • • • • • • • •333 33 nF X5R X5R X5R • • • • • • • • • •393 39 nF X5R • • • • • • • • • •473 47 nF X5R • • • • • • • • • •563 56 nF • • • • • • • • •683 68 nF • • • • • • • • •823 82 nF • • • • • • • • •104 100 nF • • • • • • • •124 120 nF X5R • • • •154 150 nF X5R • • • •184 180 nF • • •224 220 nF • • •274 270 nF • • •334 330 nF • • •394 390 nF •474 470 nF564 560 nF684 680 nF824 820 nF105 1.0 μF125 1.2 μF
Revision: 17-Feb-15 187 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
Notes(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
RoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”Not RoHS-compliant
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1206 VJ1210 (1)
CASE CODE 1206 1210VOLTAGE (VDC) 16 25 50 100 200 500 16 25 50 100 200 500VOLTAGE CODE J X A B C E J X A B C ECAP. CODE CAP.
101 100 pF121 120 pF151 150 pF181 180 pF221 220 pF271 270 pF331 330 pF391 390 pF471 470 pF561 560 pF681 680 pF • • • • • •821 820 pF • • • • • •102 1.0 nF • • • • • • • • • • • •122 1.2 nF • • • • • • • • • • • •152 1.5 nF • • • • • • • • • • • •182 1.8 nF • • • • • • • • • • • •222 2.2 nF • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • •562 5.6 nF • • • • • • • • • • • •682 6.8 nF • • • • • • • • • • • •822 8.2 nF • • • • • • • • • • • •103 10 nF • • • • • • • • • • • •123 12 nF • • • • • • • • • • • •153 15 nF • • • • • • • • • • • •183 18 nF • • • • • • • • • • • •223 22 nF • • • • • • • • • • •273 27 nF • • • • • • • • • • •333 33 nF • • • • • • • • • • •393 39 nF • • • • • • • • • • •473 47 nF • • • • • • • • • • •563 56 nF • • • • • • • • • •683 68 nF • • • • • • • • • •823 82 nF • • • • • • • • • •104 100 nF • • • • • • • • • •124 120 nF • • • • • • • • •154 150 nF • • • • • • • • •184 180 nF • • • • • • • •224 220 nF • • • • • • • •274 270 nF • • • • • • • •334 330 nF • • • • • • •394 390 nF • • • • • •474 470 nF • • • • • •564 560 nF • • • • •684 680 nF • • • • •824 820 nF • • • • •105 1.0 μF • • • • •125 1.2 μF
Revision: 17-Feb-15 188 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
Notes(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
RoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”Not RoHS-compliant
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1808 (1) VJ1812 (1) VJ1825 (1)
CASE CODE 1808 (1) 1812 (1) 1825 (1)
VOLTAGE (VDC) 25 50 100 200 500 25 50 75 100 200 250 500 25 50 100 200 500VOLTAGE CODE X A B C E X A K B C P E X A B C ECAP. CODE CAP.
102 1.0 nF • • • • •222 1.2 nF • • • • •152 1.5 nF • • • • •182 1.8 nF • • • • •222 2.2 nF • • • • •272 2.7 nF • • • • •332 3.3 nF • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • •562 5.6 nF • • • • • • • • • • • •682 6.8 nF • • • • • • • • • • • •822 8.2 nF • • • • • • • • • • • •103 10 nF • • • • • • • • • • • • • • • • •123 12 nF • • • • • • • • • • • • • • • • •153 15 nF • • • • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • • • • • •393 39 nF • • • • • • • • • • • • • • • •473 47 nF • • • • • • • • • • • • • • • •563 56 nF • • • • • • • • • • • • • • • •683 68 nF • • • • • • • • • • • • • • • •823 82 nF • • • • • • • • • • • • • • • •104 100 nF • • • • • • • • • • • • • • • •124 120 nF • • • • • • • • • • • • • • •154 150 nF • • • • • • • • • • • • • •184 180 nF • • • • • • • • • • • • • •224 220 nF • • • • • • • • • • • • •274 270 nF • • • • • • • • • • • •334 330 nF • • • • • • • • • •394 390 nF • • • • • • • • •474 470 nF • • • • • • • • •564 560 nF • • • • • • • •684 680 nF • • • • • • • •824 820 nF • • • • • • •105 1.0 μF • • • • •125 1.2 μF • • •155 1.5 μF • • •185 1.8 μF • •225 2.2 μF •275 2.7 μF •335 3.3 μF395 3.9 μF475 4.7 μF565 5.6 μF685 6.8 μF825 8.2 μF
Revision: 17-Feb-15 189 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
Notes(1) See soldering recommendations within this data book, or visit: www.vishay.com/doc?45034
RoHS-compliant except when supplied with lead (Pb)-containing termination, code “L”Not RoHS-compliant
SELECTION CHARTDIELECTRIC X7RSTYLE VJ2220 (1) VJ2225 (1) VJ3640 (1)
CASE CODE 2220 (1) 2225 (1) 3640 (1)
VOLTAGE (VDC) 25 50 100 200 500 25 50 100 200 500 25 50 100 200 500VOLTAGE CODE X A B C E X A B C E X A B C ECAP. CODE CAP.
102 1.0 nF222 1.2 nF152 1.5 nF182 1.8 nF222 2.2 nF272 2.7 nF332 3.3 nF392 3.9 nF472 4.7 nF562 5.6 nF682 6.8 nF822 8.2 nF103 10 nF • • • • • • • • • •123 12 nF • • • • • • • • • •153 15 nF • • • • • • • • • • • • • • •183 18 nF • • • • • • • • • • • • • • •223 22 nF • • • • • • • • • • • • • • •273 27 nF • • • • • • • • • • • • • • •333 33 nF • • • • • • • • • • • • • • •393 39 nF • • • • • • • • • • • • • • •473 47 nF • • • • • • • • • • • • • • •563 56 nF • • • • • • • • • • • • • • •683 68 nF • • • • • • • • • • • • • • •823 82 nF • • • • • • • • • • • • • • •104 100 nF • • • • • • • • • • • • • • •124 120 nF • • • • • • • • • • • • • • •154 150 nF • • • • • • • • • • • • • • •184 180 nF • • • • • • • • • • • • • • •224 220 nF • • • • • • • • • • • • • • •274 270 nF • • • • • • • • • • • • • •334 330 nF • • • • • • • • • • • • • •394 390 nF • • • • • • • • • • • • •474 470 nF • • • • • • • • • • • • •564 560 nF • • • • • • • • • • • • •684 680 nF • • • • • • • • • • • • •824 820 nF • • • • • • • • • • • •105 1.0 μF • • • • • • • • • • • •125 1.2 μF • • • • • • • • • • •155 1.5 μF • • • • • • • • •185 1.8 μF • • • • • • • • •225 2.2 μF • • • • • • •275 2.7 μF • • • • •335 3.3 μF • • • •395 3.9 μF • • • •475 4.7 μF • • •
565 5.6 μF •
685 6.8 μF •
825 8.2 μF
Revision: 17-Feb-15 190 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
HI-REL C0G (NP0) DIELECTRIC - TYPICAL PARAMETERS
- 75 - 50 - 25 100 125
2.0
1.5
1.0
0.5
0.0
- 0.5
- 1.0
- 1.5
- 2.0
TEMPERATURE COEFFICIENT OF CAPACITANCE
NP0
TEMPERATURE °C
% C
AP
AC
ITA
NC
E C
HA
NG
E
0 25 50 75TEMPERATURE °C
10 25 100 125
10 000
1000
100
10
INS
UL
AT
ION
RE
SIS
TA
NC
E(Ω
F)
MINIMUM INSULATION RESISTANCE VS. TEMPERATURE
HOURS
0.2
0.1
0.0
- 0.1
- 0.2
% C
AP
AC
ITA
NC
E C
HA
NG
E
AGING RATE
1 10 100 1000 10 000 0 100 200 300 400 500 600 700 800 900 1000
10
0
- 20
- 30
DC VOLTS APPLIED
- 10
20
30VOLTAGE COEFICIENT OF CAPACITANCE
% C
APA
CIT
AN
CE
CH
AN
GE
CHANGE OF CAPACITANCE WITH FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
2
1
0
- 1
- 2
% C
APA
CIT
AN
CE
CH
AN
GE
DISSIPATION FACTOR VS. FREQUENCY
FREQUENCY1 kHz 10 kHz 100 kHz 1 MHz
0.00025
DIS
SIP
AT
ION
FA
CT
OR
0.0005
0.001
Revision: 17-Feb-15 191 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
HI-REL X7R/X5R DIELECTRIC - TYPICAL PARAMETERS
TEMPERATURE COEFFICIENT OF CAPACITANCE
- 20
- 15
- 10
- 5
0
5
10
15
20
TEMPERATURE (°C)
% C
AP
AC
ITA
NC
E C
HA
NG
E
- 75 - 50 - 25 0 25 50 75 100 125
X5R
X7R
TEMPERATURE (°C)
MIN. INSULATION RESISTANCE VS. TEMPERATURE
10 25 100 125
10 000
1000
100
10
INS
UL
AT
ION
RE
SIS
TA
NC
E (
ΩF
)AGING RATE
HOURS
1 10 100 1000 10 000
1.0
0.0
- 1.0
- 2.0
- 3.0
- 4.0
% C
APA
CIT
AN
CE
CH
AN
GE
- 75 - 50 - 25 0 25 50 75 100 1250.0
DISSIPATION FACTOR VS. TEMPERATURE
TEMPERATURE (°C)
% D
ISS
IPA
TIO
N F
AC
TO
R
X7R
X5R
0.51.01.52.02.53.03.54.04.55.05.56.0
DC VOLTS APPLIED
00.004
DIS
SIP
AT
ION
FA
CT
OR
UN/V-
DISSIPATION FACTOR VS. VOLTAGE
50 V
100 V
0.020
0.016
0.012
0.008
10010 20 30 40 50 60 70 80 90
DC VOLTS APPLIED
00.004
DIS
SIP
AT
ION
FA
CT
OR
UN/V-
DISSIPATION FACTOR VS. VOLTAGE
0.020
0.016
0.012
0.008
700100 200 300 400 500
500 V200 V
600
Revision: 17-Feb-15 192 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Hi-Rel Serieswww.vishay.com Vishay Vitramon
Notes(1) Vishay Vitramon uses embossed plastic carrier tape(2) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(3) n/a = not available(4) Packaging “C”/”P”/”O”/”I” and “T”/”R” or lower quantities can depend from product thickness
STANDARD PACKAGING QUANTITIES (1)(2)(3)
CASE CODE
TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PAPER TAPE PACKAGING CODE
“C”/“O”
PLASTIC TAPE PACKAGING CODE
“T”
LOW QUANTITY PACKAGING CODE
“J”
PAPER TAPE PACKAGING CODE
“P”/“I”
PLASTIC TAPE PACKAGING CODE
“R”
0402 8 mm 5000 n/a 1000 10 000 n/a
0603 (4) 8 mm 4000 4000 1000 10 000 10 000
0805 (4) 8 mm 3000 3000 1000 10 000 10 000
1206 (4) 8 mm 3000 3000/2500 1000 10 000 10 000/9000
1210 (4) 8 mm n/a 3000/2500/2000 1000 n/a 10 000/9000
1808 12 mm n/a 2000 500 n/a 10 000
1812 12 mm n/a 1000 500 n/a 4000
1825 12 mm n/a 1000 500 n/a 4000
2220 12 mm n/a 1000 500 n/a 4000
2225 12 mm n/a 1000 500 n/a 4000
3640 16 mm n/a 500 n/a n/a n/a
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to +40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 17-Feb-15 193 Document Number: 45200For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CDR-MIL-PRF-55681www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip CapacitorsMIL Qualified, Type CDR
FEATURES• Military qualified products
• Federal stock control number, CAGE CODE SHV71
• High reliability tested per MIL-PRF-55681
• Tin/lead termination codes “Z” and “U”
• Lead (Pb)-free termination codes “W”, “Y”, “M”
• Wet build process
• Reliable Noble Metal Electrode (NME) system
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
Note* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information / tables in this datasheet for details.
APPLICATIONS• Avionic systems
• Sonar systems
• Satellite systems
• Missiles applications
• Geographical information systems
• Global positioning systems
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at + 25 °C unless otherwise specified
Operating Temperature: - 55 °C to + 125 °C
Capacitance Range: 1.0 pF to 470 nF
Voltage Range: 50 VDC to 100 VDC
Temperature Coefficient of Capacitance (TCC):
BP: 0 ppm/°C ± 30 ppm/°C from - 55 °C to + 125 °C,with 0 VDC applied
BX: ± 15 % from - 55 °C to + 125 °C, with 0 VDC applied
BX: + 15 %, - 25 % from - 55 °C to + 125 °C, with 100 % rated VDC applied
Dissipation Factor (DF):
BP: 0.15 % maximumBX: 2.50 % maximum
Test frequency: 1 MHz ± 50 kHz for BP capacitors 1000 pF and for BX capacitors 100 pFAll other BP and BX at 1 kHz ± 50 Hz
Aging Rate:
BP: 0 % maximum per decadeBX: 1 % maximum per decade
Insulation Resistance (IR):
At + 25 °C and rated voltage 100 000 M minimum or1000 F, whichever is less
Dielectric Strength Test:
Performed per method 103 of EIA-198-2-E.Applied test voltages: 100 VDC-rated: 250 % of rated voltage
Available
Available
Revision: 28-Mar-13 194 Document Number: 45026For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CDR-MIL-PRF-55681www.vishay.com Vishay Vitramon
Note• Detail ratings see selection chart
Notes(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected](2) Available tolerances please see rating chart(3) MIL-PRF-55681 “U” termination part number have increased dimensions
QUICK REFERENCE DATA
DIELECTRIC STYLE (CASE)MAXIMUM VOLTAGE
(V)
CAPACITANCE
MINIMUM MAXIMUM
BP CDR01 (0805) 100 10 pF 180 pF
BX CDR01 (0805) 100 120 pF 4.7 nF
BP CDR02 (1805) 100 220 pF 270 pF
BX CDR02 (1805) 100 3.9 nF 22 nF
BP CDR03 (1808) 100 330 pF 1.0 nF
BX CDR03 (1808) 100 12 nF 68 nF
BP CDR04 (1812) 100 1.2 nF 3.3 nF
BX CDR04 (1812) 100 39 nF 180 nF
BX CDR06 (2225) 50 390 nF 470 nF
BP CDR31 (0805) 100 1.0 pF 680 pF
BX CDR31 (0805) 100 470 pF 18 nF
BP CDR32 (1206) 100 1.0 pF 2.2 nF
BX CDR32 (1206) 100 4.7 nF 39 nF
BP CDR33 (1210) 100 1.0 nF 3.3 nF
BX CDR33 (1210) 100 15 nF 100 nF
BP CDR34 (1812) 100 2.2 nF 10 nF
BX CDR34 (1812) 100 27 nF 180 nF
BP CDR35 (1825) 100 4.7 nF 22 nF
BX CDR35 (1825) 100 56 nF 470 nF
ORDERING INFORMATION - MILITARYCDR31 BX 102 A K Y S A T
MILITARY STYLE
DIELECTRIC CAPACITANCE NOMINAL
CODE
DC VOLTAGE RATING (1)
CAPACITANCE TOLERANCE (2)
TERMINATION FAILURE RATE
MARKING PACKAGING
CDR01CDR02CDR03CDR04CDR06CDR31CDR32CDR33CDR34CDR35
BP and BX Expressed in picofarads (pF).
The first two digits are
significant, the third is a multiplier. Examples:
102 = 1000 pF1R8 = 1.8 pF
A = 50 VB = 100 V
C = ± 0.25 pFD = ± 0.5 pF
F = ± 1 %J = ± 5 %
K = ± 10 %M = ± 20 %
M = Silver PalladiumY = Ni barrier with
100 % tin W = Ni barrier with
100 % tin Z = Ni barrier with
tin/lead platemin. 4 % leadU = Hot solder
dipped(min. of 4 % lead) (3)
M = 1.0 %P = 0.1 %
R = 0.01 %S = 0.001 %
Consult factory for failure rate
status
A = Unmarked
T = 7" reel/plastic tapeJ = 7" reel (low quantity)C = 7" reel/paper tape
R = 11 1/4"/13" reel/plastic tapeP = 11 1/4"/13" reel/paper tape
B = Bulk
Revision: 28-Mar-13 195 Document Number: 45026For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CDR-MIL-PRF-55681www.vishay.com Vishay Vitramon
DIMENSIONS in inches (millimeters)
MIL-PRF-55681 STYLELENGTH
(L)WIDTH
(W)MAXIMUM
THICKNESS (T) TERM. (P)
MINIMUM MAXIMUM
/1
CDR01 0.080 ± 0.015 (2.03 ± 0.38) 0.050 ± 0.015 (1.27 ± 0.38) 0.055 (1.40) 0.010 (0.25) 0.030 (0.75)
CDR02 0.180 ± 0.015 (4.57 ± 0.38) 0.050 ± 0.015 (1.27 ± 0.38) 0.055 (1.40) 0.010 (0.25) 0.030 (0.75)
CDR03 0.180 ± 0.015 (4.57 ± 0.38) 0.080 ± 0.015 (2.03 ± 0.38) 0.080 (2.03) 0.010 (0.25) 0.030 (0.75)
CDR04 0.180 ± 0.015 (4.57 ± 0.38) 0.125 ± 0.015 (3.20 ± 0.38) 0.080 (2.03) 0.010 (0.25) 0.030 (0.75)
/3 CDR06 0.225 ± 0.020 (5.72 ± 0.51) 0.250 ± 0.020 (6.35 ± 0.51) 0.080 (2.03) 0.010 (0.25) 0.030 (0.75)
/7 CDR31 0.078 ± 0.008 (2.00 ± 0.20) 0.049 ± 0.008 (1.25 ± 0.20) 0.051 (1.30) 0.012 (0.30) 0.028 (0.70)
/8 CDR32 0.125 ± 0.008 (3.20 ± 0.20) 0.062 ± 0.008 (1.60 ± 0.20) 0.051 (1.30) 0.012 (0.30) 0.028 (0.70)
/9 CDR33 0.125 ± 0.010 (3.20 ± 0.25) 0.098 ± 0.010 (2.50 ± 0.25) 0.059 (1.50) 0.010 (0.25) 0.030 (0.75)
/10 CDR34 0.176 ± 0.010 (4.50 ± 0.25) 0.125 ± 0.010 (3.20 ± 0.25) 0.059 (1.50) 0.010 (0.25) 0.030 (0.75)
/11 CDR35 0.176 ± 0.012 (4.50 ± 0.30) 0.250 ± 0.012 (6.40 ± 0.30) 0.059 (1.50) 0.008 (0.20) 0.032 (0.80)
LW
TMAX.
P
“U” TERMINATION in inches (millimeters)STYLE LENGTH WIDTH/THICKNESS PACKAGING CODES
CDR01 0.020 (0.51) 0.015 (0.38) “C”, “J”, “P”, “B”
CDR02 to CDR06 0.025 (0.64) 0.015 (0.38) “T”, “J”, “R”, “B”
CDR31 0.023 (0.60) 0.012 (0.30) “C”, “J”, “P”, “B”
CDR32 to CDR35 0.023 (0.60) 0.012 (0.30) “T”, “J”, “R”, “B”
MIL-C-55681 QUALIFIED, TYPE CDRMILITARY TYPE DESIGNATION
CAPACITANCECODE
CAPACITANCE(pF)
CAPACITANCETOLERANCE
RATED TEMP. AND VOLTAGE TEMP. LIMITS
VOLTAGE(DC)
RoHSSTATUS
CDR01BPCDR01BP100B_ _ _ 100 10 J, K BP 100CDR01BP120BJ_ _ 120 12 J BP 100CDR01BP150B_ _ _ 150 15 J, K BP 100CDR01BP180BJ_ _ 180 18 J BP 100CDR01BP220B_ _ _ 220 22 J, K BP 100CDR01BP270BJ_ _ 270 27 J BP 100CDR01BP330B_ _ _ 330 33 J, K BP 100CDR01BP390BJ_ _ 390 39 J BP 100CDR01BP470B_ _ _ 470 47 J, K BP 100CDR01BP560BJ_ _ 560 56 J BP 100CDR01BP680B_ _ _ 680 68 J, K BP 100CDR01BP820BJ_ _ 820 82 J BP 100CDR01BP101B_ _ _ 101 100 J, K BP 100
CDR01BP121B_ _ _ 121 120 J, K BP 100
CDR01BP151B_ _ _ 151 150 J, K BP 100
CDR01BP181B_ _ _ 181 180 J, K BP 100
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
Revision: 28-Mar-13 196 Document Number: 45026For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CDR-MIL-PRF-55681www.vishay.com Vishay Vitramon
CDR01BX CDR01BX121B_ _ _ 121 120 J, K BX 100CDR01BX151B_ _ _ 151 150 J, K BX 100CDR01BX181B_ _ _ 181 180 J, K BX 100CDR01BX221B_ _ _ 221 220 K, M BX 100CDR01BX271BK_ _ 271 270 K BX 100CDR01BX331B_ _ _ 331 330 K, M BX 100CDR01BX391BK_ _ 391 390 K BX 100CDR01BX471B_ _ _ 471 470 K, M BX 100CDR01BX561BK_ _ 561 560 K BX 100CDR01BX681B_ _ _ 681 680 K, M BX 100CDR01BX821BK_ _ 821 820 K BX 100CDR01BX102B_ _ _ 102 1000 K, M BX 100CDR01BX122BK_ _ 122 1200 K BX 100CDR01BX152B_ _ _ 152 1500 K, M BX 100CDR01BX182BK_ _ 182 1800 K BX 100CDR01BX222B_ _ _ 222 2200 K, M BX 100CDR01BX272BK_ _ 272 2700 K BX 100CDR01BX332B_ _ _ 332 3300 K, M BX 100CDR01BX392AK_ _ 392 3900 K BX 50CDR01BX472A_ _ _ 472 4700 K, M BX 50CDR02BP CDR02BP221B_ _ _ 221 220 J, K BP 100CDR02BP271BJ_ _ 271 270 J BP 100CDR02BX CDR02BX392BK_ _ 392 3900 K BX 100CDR02BX472B_ _ _ 472 4700 K, M BX 100CDR02BX562BK_ _ 562 5600 K BX 100CDR02BX682B_ _ _ 682 6800 K, M BX 100CDR02BX822BK_ _ 822 8200 K BX 100CDR02BX103B_ _ _ 103 10 000 K, M BX 100CDR02BX123AK_ _ 123 12 000 K BX 50CDR02BX153A_ _ _ 153 15 000 K, M BX 50CDR02BX183AK_ _ 183 18 000 K BX 50CDR02BX223A_ _ _ 223 22 000 K, M BX 50CDR03BPCDR03BP331B_ _ _ 331 330 J, K BP 100CDR03BP391BJ_ _ 391 390 J BP 100CDR03BP471B_ _ _ 471 470 J, K BP 100CDR03BP561BJ_ _ 561 560 J BP 100CDR03BP681B_ _ _ 681 680 J, K BP 100CDR03BP821BJ_ _ 821 820 J BP 100CDR03BP102B_ _ _ 102 1000 J, K BP 100CDR03BX CDR03BX123BK_ _ 123 12 000 K BX 100CDR03BX153B_ _ _ 153 15 000 K, M BX 100CDR03BX183BK_ _ 183 18 000 K BX 100CDR03BX223B_ _ _ 223 22 000 K, M BX 100CDR03BX273BK_ _ 273 27 000 K BX 100CDR03BX333B_ _ _ 333 33 000 K, M BX 100CDR03BX393AK_ _ 393 39 000 K BX 50CDR03BX473A_ _ _ 473 47 000 K, M BX 50CDR03BX563AK_ _ 563 56 000 K BX 50CDR03BX683A_ _ _ 683 68 000 K, M BX 50
MIL-C-55681 QUALIFIED, TYPE CDRMILITARY TYPE DESIGNATION
CAPACITANCECODE
CAPACITANCE(pF)
CAPACITANCETOLERANCE
RATED TEMP. AND VOLTAGE TEMP. LIMITS
VOLTAGE(DC)
RoHSSTATUS
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
Revision: 28-Mar-13 197 Document Number: 45026For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CDR-MIL-PRF-55681www.vishay.com Vishay Vitramon
CDR04BP
CDR04BP122BJ_ _ 122 1200 J BP 100
CDR04BP152B_ _ _ 152 1500 J, K BP 100
CDR04BP182BJ_ _ 182 1800 J BP 100
CDR04BP222B_ _ _ 222 2200 J, K BP 100
CDR04BP272BJ_ _ 272 2700 J BP 100
CDR04BP332B_ _ _ 332 3300 J, K BP 100
CDR04BX
CDR04BX393BK_ _ 393 39 000 K BX 100
CDR04BX473B_ _ _ 473 47 000 K, M BX 100
CDR04BX563BK_ _ 563 56 000 K BX 100
CDR04BX823AK_ _ 823 82 000 K BX 50
CDR04BX104A_ _ _ 104 100 000 K, M BX 50
CDR04BX124AK_ _ 124 120 000 K BX 50
CDR04BX154A_ _ _ 154 150 000 K, M BX 50
CDR04BX184AK_ _ 184 180 000 K BX 50
CDR06BX
CDR06BX394AK_ _ 394 390 000 K BX 50
CDR06BX474A_ _ _ 474 470 000 K, M BX 50
CDR31BP
CDR31BP1R0B_ _ _ 1R0 1 C BP 100
CDR31BP1R1B_ _ _ 1R1 1.1 C BP 100
CDR31BP1R2B_ _ _ 1R2 1.2 C BP 100
CDR31BP1R3B_ _ _ 1R3 1.3 C BP 100
CDR31BP1R5B_ _ _ 1R5 1.5 C BP 100
CDR31BP1R6B_ _ _ 1R6 1.6 C BP 100
CDR31BP1R8B_ _ _ 1R8 1.8 C BP 100
CDR31BP2R0B_ _ _ 2R0 2 C BP 100
CDR31BP2R2B_ _ _ 2R2 2.2 C BP 100
CDR31BP2R4B_ _ _ 2R4 2.4 C BP 100
CDR31BP2R7B_ _ _ 2R7 2.7 C, D BP 100
CDR31BP3R0B_ _ _ 3R0 3 C, D BP 100
CDR31BP3R3B_ _ _ 3R3 3.3 C, D BP 100
CDR31BP3R6B_ _ _ 3R6 3.6 C, D BP 100
CDR31BP3R9B_ _ _ 3R9 3.9 C, D BP 100
CDR31BP4R3B_ _ _ 4R3 4.3 C, D BP 100
CDR31BP4R7B_ _ _ 4R7 4.7 C, D BP 100
CDR31BP5R1B_ _ _ 5R1 5.1 C, D BP 100
CDR31BP5R6B_ _ _ 5R6 5.6 C, D BP 100
CDR31BP6R2B_ _ _ 6R2 6.2 C, D BP 100
CDR31BP6R8B_ _ _ 6R8 6.8 C, D BP 100
CDR31BP7R5B_ _ _ 7R5 7.5 C, D BP 100
CDR31BP8R2B_ _ _ 8R2 8.2 C, D BP 100
CDR31BP9R1B_ _ _ 9R1 9.1 C, D BP 100
CDR31BP100B_ _ _ 100 10 F, J, K BP 100
CDR31BP110B_ _ _ 110 11 F, J, K BP 100
MIL-C-55681 QUALIFIED, TYPE CDRMILITARY TYPE DESIGNATION
CAPACITANCECODE
CAPACITANCE(pF)
CAPACITANCETOLERANCE
RATED TEMP. AND VOLTAGE TEMP. LIMITS
VOLTAGE(DC)
RoHSSTATUS
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
Revision: 28-Mar-13 198 Document Number: 45026For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CDR-MIL-PRF-55681www.vishay.com Vishay Vitramon
CDR31BP
CDR31BP120B_ _ _ 120 12 F, J, K BP 100
CDR31BP130B_ _ _ 130 13 F, J, K BP 100
CDR31BP150B_ _ _ 150 15 F, J, K BP 100
CDR31BP160B_ _ _ 160 16 F, J, K BP 100
CDR31BP180B_ _ _ 180 18 F, J, K BP 100
CDR31BP200B_ _ _ 200 20 F, J, K BP 100
CDR31BP220B_ _ _ 220 22 F, J, K BP 100
CDR31BP240B_ _ _ 240 24 F, J, K BP 100
CDR31BP270B_ _ _ 270 27 F, J, K BP 100
CDR31BP300B_ _ _ 300 30 F, J, K BP 100
CDR31BP330B_ _ _ 330 33 F, J, K BP 100
CDR31BP360B_ _ _ 360 36 F, J, K BP 100
CDR31BP390B_ _ _ 390 39 F, J, K BP 100
CDR31BP430B_ _ _ 430 43 F, J, K BP 100
CDR31BP470B_ _ _ 470 47 F, J, K BP 100
CDR31BP510B_ _ _ 510 51 F, J, K BP 100
CDR31BP560B_ _ _ 560 56 F, J, K BP 100
CDR31BP620B_ _ _ 620 62 F, J, K BP 100
CDR31BP680B_ _ _ 680 68 F, J, K BP 100
CDR31BP750B_ _ _ 750 75 F, J, K BP 100
CDR31BP820B_ _ _ 820 82 F, J, K BP 100
CDR31BP910B_ _ _ 910 91 F, J, K BP 100
CDR31BP101B_ _ _ 101 100 F, J, K BP 100
CDR31BP111B_ _ _ 111 110 F, J, K BP 100
CDR31BP121B_ _ _ 121 120 F, J, K BP 100
CDR31BP131B_ _ _ 131 130 F, J, K BP 100
CDR31BP151B_ _ _ 151 150 F, J, K BP 100
CDR31BP161B_ _ _ 161 160 F, J, K BP 100
CDR31BP181B_ _ _ 181 180 F, J, K BP 100
CDR31BP201B_ _ _ 201 200 F, J, K BP 100
CDR31BP221B_ _ _ 221 220 F, J, K BP 100
CDR31BP241B_ _ _ 241 240 F, J, K BP 100
CDR31BP271B_ _ _ 271 270 F, J, K BP 100
CDR31BP301B_ _ _ 301 300 F, J, K BP 100
CDR31BP331B_ _ _ 331 330 F, J, K BP 100
CDR31BP361B_ _ _ 361 360 F, J, K BP 100
CDR31BP391B_ _ _ 391 390 F, J, K BP 100
CDR31BP431B_ _ _ 431 430 F, J, K BP 100
CDR31BP471B_ _ _ 471 470 F, J, K BP 100
CDR31BP511A_ _ _ 511 510 F, J, K BP 50
CDR31BP561A_ _ _ 561 560 F, J, K BP 50
CDR31BP621A_ _ _ 621 620 F, J, K BP 50
CDR31BP681A_ _ _ 681 680 F, J, K BP 50
MIL-C-55681 QUALIFIED, TYPE CDRMILITARY TYPE DESIGNATION
CAPACITANCECODE
CAPACITANCE(pF)
CAPACITANCETOLERANCE
RATED TEMP. AND VOLTAGE TEMP. LIMITS
VOLTAGE(DC)
RoHSSTATUS
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
Revision: 28-Mar-13 199 Document Number: 45026For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CDR-MIL-PRF-55681www.vishay.com Vishay Vitramon
CDR31BX
CDR31BX471B_ _ _ 471 470 K, M BX 100
CDR31BX561B_ _ _ 561 560 K, M BX 100
CDR31BX681B_ _ _ 681 680 K, M BX 100
CDR31BX821B_ _ _ 821 820 K, M BX 100
CDR31BX102B_ _ _ 102 1000 K, M BX 100
CDR31BX122B_ _ _ 122 1200 K, M BX 100
CDR31BX152B_ _ _ 152 1500 K, M BX 100
CDR31BX182B_ _ _ 182 1800 K, M BX 100
CDR31BX222B_ _ _ 222 2200 K, M BX 100
CDR31BX272B_ _ _ 272 2700 K, M BX 100
CDR31BX332B_ _ _ 332 3300 K, M BX 100
CDR31BX392B_ _ _ 392 3900 K, M BX 100
CDR31BX472B_ _ _ 472 4700 K, M BX 100
CDR31BX562A_ _ _ 562 5600 K, M BX 50
CDR31BX682A_ _ _ 682 6800 K, M BX 50
CDR31BX822A_ _ _ 822 8200 K, M BX 50
CDR31BX103A_ _ _ 103 10 000 K, M BX 50
CDR31BX123A_ _ _ 123 12 000 K, M BX 50
CDR31BX153A_ _ _ 153 15 000 K, M BX 50
CDR31BX183A_ _ _ 183 18 000 K, M BX 50
CDR32BP
CDR32BP1R0B_ _ _ 1R0 1 C BP 100
CDR32BP1R1B_ _ _ 1R1 1.1 C BP 100
CDR32BP1R2B_ _ _ 1R2 1.2 C BP 100
CDR32BP1R3B_ _ _ 1R3 1.3 C BP 100
CDR32BP1R5B_ _ _ 1R5 1.5 C BP 100
CDR32BP1R6B_ _ _ 1R6 1.6 C BP 100
CDR32BP1R8B_ _ _ 1R8 1.8 C BP 100
CDR32BP2R0B_ _ _ 2R0 2 C BP 100
CDR32BP2R2B_ _ _ 2R2 2.2 C BP 100
CDR32BP2R4B_ _ _ 2R4 2.4 C BP 100
CDR32BP2R7B_ _ _ 2R7 2.7 C, D BP 100
CDR32BP3R0B_ _ _ 3R0 3 C, D BP 100
CDR32BP3R3B_ _ _ 3R3 3.3 C, D BP 100
CDR32BP3R6B_ _ _ 3R6 3.6 C, D BP 100
CDR32BP3R9B_ _ _ 3R9 3.9 C, D BP 100
CDR32BP4R3B_ _ _ 4R3 4.3 C, D BP 100
CDR32BP4R7B_ _ _ 4R7 4.7 C, D BP 100
CDR32BP5R1B_ _ _ 5R1 5.1 C, D BP 100
CDR32BP5R6B_ _ _ 5R6 5.6 C, D BP 100
CDR32BP6R2B_ _ _ 6R2 6.2 C, D BP 100
CDR32BP6R8B_ _ _ 6R8 6.8 C, D BP 100
CDR32BP7R5B_ _ _ 7R5 7.5 C, D BP 100
CDR32BP8R2B_ _ _ 8R2 8.2 C, D BP 100
CDR32BP9R1B_ _ _ 9R1 9.1 C, D BP 100
CDR32BP100B_ _ _ 100 10 F, J, K BP 100
MIL-C-55681 QUALIFIED, TYPE CDRMILITARY TYPE DESIGNATION
CAPACITANCECODE
CAPACITANCE(pF)
CAPACITANCETOLERANCE
RATED TEMP. AND VOLTAGE TEMP. LIMITS
VOLTAGE(DC)
RoHSSTATUS
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
Revision: 28-Mar-13 200 Document Number: 45026For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CDR-MIL-PRF-55681www.vishay.com Vishay Vitramon
CDR32BP
CDR32BP110B_ _ _ 110 11 F, J, K BP 100
CDR32BP120B_ _ _ 120 12 F, J, K BP 100
CDR32BP130B_ _ _ 130 13 F, J, K BP 100
CDR32BP150B_ _ _ 150 15 F, J, K BP 100
CDR32BP160B_ _ _ 160 16 F, J, K BP 100
CDR32BP180B_ _ _ 180 18 F, J, K BP 100
CDR32BP200B_ _ _ 200 20 F, J, K BP 100
CDR32BP220B_ _ _ 220 22 F, J, K BP 100
CDR32BP240B_ _ _ 240 24 F, J, K BP 100
CDR32BP270B_ _ _ 270 27 F, J, K BP 100
CDR32BP300B_ _ _ 300 30 F, J, K BP 100
CDR32BP330B_ _ _ 330 33 F, J, K BP 100
CDR32BP360B_ _ _ 360 36 F, J, K BP 100
CDR32BP390B_ _ _ 390 39 F, J, K BP 100
CDR32BP430B_ _ _ 430 43 F, J, K BP 100
CDR32BP470B_ _ _ 470 47 F, J, K BP 100
CDR32BP510B_ _ _ 510 51 F, J, K BP 100
CDR32BP560B_ _ _ 560 56 F, J, K BP 100
CDR32BP620B_ _ _ 620 62 F, J, K BP 100
CDR32BP680B_ _ _ 680 68 F, J, K BP 100
CDR32BP750B_ _ _ 750 75 F, J, K BP 100
CDR32BP820B_ _ _ 820 82 F, J, K BP 100
CDR32BP910B_ _ _ 910 91 F, J, K BP 100
CDR32BP101B_ _ _ 101 100 F, J, K BP 100
CDR32BP111B_ _ _ 111 110 F, J, K BP 100
CDR32BP121B_ _ _ 121 120 F, J, K BP 100
CDR32BP131B_ _ _ 131 130 F, J, K BP 100
CDR32BP151B_ _ _ 151 150 F, J, K BP 100
CDR32BP161B_ _ _ 161 160 F, J, K BP 100
CDR32BP181B_ _ _ 181 180 F, J, K BP 100
CDR32BP201B_ _ _ 201 200 F, J, K BP 100
CDR32BP221B_ _ _ 221 220 F, J, K BP 100
CDR32BP241B_ _ _ 241 240 F, J, K BP 100
CDR32BP271B_ _ _ 271 270 F, J, K BP 100
CDR32BP301B_ _ _ 301 300 F, J, K BP 100
CDR32BP331B_ _ _ 331 330 F, J, K BP 100
CDR32BP361B_ _ _ 361 360 F, J, K BP 100
CDR32BP391B_ _ _ 391 390 F, J, K BP 100
CDR32BP431B_ _ _ 431 430 F, J, K BP 100
CDR32BP471B_ _ _ 471 470 F, J, K BP 100
CDR32BP511B_ _ _ 511 510 F, J, K BP 100
CDR32BP561B_ _ _ 561 560 F, J, K BP 100
CDR32BP621B_ _ _ 621 620 F, J, K BP 100
CDR32BP681B_ _ _ 681 680 F, J, K BP 100
CDR32BP751B_ _ _ 751 750 F, J, K BP 100
CDR32BP821B_ _ _ 821 820 F, J, K BP 100
MIL-C-55681 QUALIFIED, TYPE CDRMILITARY TYPE DESIGNATION
CAPACITANCECODE
CAPACITANCE(pF)
CAPACITANCETOLERANCE
RATED TEMP. AND VOLTAGE TEMP. LIMITS
VOLTAGE(DC)
RoHSSTATUS
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
Revision: 28-Mar-13 201 Document Number: 45026For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CDR-MIL-PRF-55681www.vishay.com Vishay Vitramon
CDR32BPCDR32BP911B_ _ _ 911 910 F, J, K BP 100
CDR32BP102B_ _ _ 102 1000 F, J, K BP 100
CDR32BP112A_ _ _ 112 1100 F, J, K BP 50
CDR32BP122A_ _ _ 122 1200 F, J, K BP 50
CDR32BP132A_ _ _ 132 1300 F, J, K BP 50
CDR32BP152A_ _ _ 152 1500 F, J, K BP 50
CDR32BP162A_ _ _ 162 1600 F, J, K BP 50
CDR32BP182A_ _ _ 182 1800 F, J, K BP 50
CDR32BP202A_ _ _ 202 2000 F, J, K BP 50
CDR32BP222A_ _ _ 222 2200 F, J, K BP 50
CDR32BX CDR32BX472B_ _ _ 472 4700 K, M BX 100
CDR32BX562B_ _ _ 562 5600 K, M BX 100
CDR32BX682B_ _ _ 682 6800 K, M BX 100
CDR32BX822B_ _ _ 822 8200 K, M BX 100
CDR32BX103B_ _ _ 103 10 000 K, M BX 100
CDR32BX123B_ _ _ 123 12 000 K, M BX 100
CDR32BX153B_ _ _ 153 15 000 K, M BX 100
CDR32BX183A_ _ _ 183 18 000 K, M BX 50
CDR32BX223A_ _ _ 223 22 000 K, M BX 50
CDR32BX273A_ _ _ 273 27 000 K, M BX 50
CDR32BX333A_ _ _ 333 33 000 K, M BX 50
CDR32BX393A_ _ _ 393 39 000 K, M BX 50
CDR33BPCDR33BP102B_ _ _ 102 1000 F, J, K BP 100
CDR33BP112B_ _ _ 112 1100 F, J, K BP 100
CDR33BP122B_ _ _ 122 1200 F, J, K BP 100
CDR33BP132B_ _ _ 132 1300 F, J, K BP 100
CDR33BP152B_ _ _ 152 1500 F, J, K BP 100
CDR33BP162B_ _ _ 162 1600 F, J, K BP 100
CDR33BP182B_ _ _ 182 1800 F, J, K BP 100
CDR33BP202B_ _ _ 202 2000 F, J, K BP 100
CDR33BP222B_ _ _ 222 2200 F, J, K BP 100
CDR33BP242A_ _ _ 242 2400 F, J, K BP 50
CDR33BP272A_ _ _ 272 2700 F, J, K BP 50
CDR33BP302A_ _ _ 302 3000 F, J, K BP 50
CDR33BP332A_ _ _ 332 3300 F, J, K BP 50
CDR33BX
CDR33BX153B_ _ _ 153 15 000 K, M BX 100
CDR33BX183B_ _ _ 183 18 000 K, M BX 100
CDR33BX223B_ _ _ 223 22 000 K, M BX 100
CDR33BX273B_ _ _ 273 27 000 K, M BX 100
CDR33BX393A_ _ _ 393 39 000 K, M BX 50
CDR33BX473A_ _ _ 473 47 000 K, M BX 50
CDR33BX563A_ _ _ 563 56 000 K, M BX 50
CDR33BX683A_ _ _ 683 68 000 K, M BX 50
CDR33BX823A_ _ _ 823 82 000 K, M BX 50
CDR33BX104A_ _ _ 104 100 000 K, M BX 50
MIL-C-55681 QUALIFIED, TYPE CDRMILITARY TYPE DESIGNATION
CAPACITANCECODE
CAPACITANCE(pF)
CAPACITANCETOLERANCE
RATED TEMP. AND VOLTAGE TEMP. LIMITS
VOLTAGE(DC)
RoHSSTATUS
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
Revision: 28-Mar-13 202 Document Number: 45026For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CDR-MIL-PRF-55681www.vishay.com Vishay Vitramon
CDR34BP
CDR34BP222B_ _ _ 222 2200 F, J, K BP 100
CDR34BP242B_ _ _ 242 2400 F, J, K BP 100
CDR34BP272B_ _ _ 272 2700 F, J, K BP 100
CDR34BP302B_ _ _ 302 3000 F, J, K BP 100
CDR34BP332B_ _ _ 332 3300 F, J, K BP 100
CDR34BP362B_ _ _ 362 3600 F, J, K BP 100
CDR34BP392B_ _ _ 392 3900 F, J, K BP 100
CDR34BP432B_ _ _ 432 4300 F, J, K BP 100
CDR34BP472B_ _ _ 472 4700 F, J, K BP 100
CDR34BP512A_ _ _ 512 5100 F, J, K BP 50
CDR34BP562A_ _ _ 562 5600 F, J, K BP 50
CDR34BP622A_ _ _ 622 6200 F, J, K BP 50
CDR34BP682A_ _ _ 682 6800 F, J, K BP 50
CDR34BP752A_ _ _ 752 7500 F, J, K BP 50
CDR34BP822A_ _ _ 822 8200 F, J, K BP 50
CDR34BP912A_ _ _ 912 9100 F, J, K BP 50
CDR34BP103A_ _ _ 103 10 000 F, J, K BP 50
CDR34BX
CDR34BX273B_ _ _ 273 27 000 K, M BX 100
CDR34BX333B_ _ _ 333 33 000 K, M BX 100
CDR34BX393B_ _ _ 393 39 000 K, M BX 100
CDR34BX473B_ _ _ 473 47 000 K, M BX 100
CDR34BX563B_ _ _ 563 56 000 K, M BX 100
CDR34BX104A_ _ _ 104 100 000 K, M BX 50
CDR34BX124A_ _ _ 124 120 000 K, M BX 50
CDR34BX154A_ _ _ 154 150 000 K, M BX 50
CDR34BX184A_ _ _ 184 180 000 K, M BX 50
CDR35BP
CDR35BP472B_ _ _ 472 4700 F, J, K BP 100
CDR35BP512B_ _ _ 512 5100 F, J, K BP 100
CDR35BP562B_ _ _ 562 5600 F, J, K BP 100
CDR35BP622B_ _ _ 622 6200 F, J, K BP 100
CDR35BP682B_ _ _ 682 6800 F, J, K BP 100
CDR35BP752B_ _ _ 752 7500 F, J, K BP 100
CDR35BP822B_ _ _ 822 8200 F, J, K BP 100
CDR35BP912B_ _ _ 912 9100 F, J, K BP 100
CDR35BP103B_ _ _ 103 10 000 F, J, K BP 100
CDR35BP113A_ _ _ 113 11 000 F, J, K BP 50
CDR35BP123A_ _ _ 123 12 000 F, J, K BP 50
CDR35BP133A_ _ _ 133 13 000 F, J, K BP 50
CDR35BP153A_ _ _ 153 15 000 F, J, K BP 50
CDR35BP163A_ _ _ 163 16 000 F, J, K BP 50
CDR35BP183A_ _ _ 183 18 000 F, J, K BP 50
CDR35BP203A_ _ _ 203 20 000 F, J, K BP 50
CDR35BP223A_ _ _ 223 22 000 F, J, K BP 50
MIL-C-55681 QUALIFIED, TYPE CDRMILITARY TYPE DESIGNATION
CAPACITANCECODE
CAPACITANCE(pF)
CAPACITANCETOLERANCE
RATED TEMP. AND VOLTAGE TEMP. LIMITS
VOLTAGE(DC)
RoHSSTATUS
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
Revision: 28-Mar-13 203 Document Number: 45026For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CDR-MIL-PRF-55681www.vishay.com Vishay Vitramon
Notes(1) Vishay Vitramon uses embossed plastic carrier tape and punched paper carrier tape(2) Paper tape is not available for case sizes > 1206 or for component thickness > 0.035" (0.89 mm)(3) DC voltage rating should not be exceeded in application
CDR35BX
CDR35BX563B_ _ _ 563 56 000 K, M BX 100
CDR35BX683B_ _ _ 683 68 000 K, M BX 100
CDR35BX823B_ _ _ 823 82 000 K, M BX 100
CDR35BX104B_ _ _ 104 100 000 K, M BX 100
CDR35BX124B_ _ _ 124 120 000 K, M BX 100
CDR35BX154B_ _ _ 154 150 000 K, M BX 100
CDR35BX184A_ _ _ 184 180 000 K, M BX 50
CDR35BX224A_ _ _ 224 220 000 K, M BX 50
CDR35BX274A_ _ _ 274 270 000 K, M BX 50
CDR35BX334A_ _ _ 334 330 000 K, M BX 50
CDR35BX394A_ _ _ 394 390 000 K, M BX 50
CDR35BX474A_ _ _ 474 470 000 K, M BX 50
MIL-C-55681 QUALIFIED, TYPE CDRMILITARY TYPE DESIGNATION
CAPACITANCECODE
CAPACITANCE(pF)
CAPACITANCETOLERANCE
RATED TEMP. AND VOLTAGE TEMP. LIMITS
VOLTAGE(DC)
RoHSSTATUS
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
TAPE AND REEL QUANTITIES (1)(2)(3)
STYLES BODY SIZE TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIESBULK
PACKAGING CODE PACKAGING CODE
“C” “T” “J” “P” “R” “B”
CDR01,CDR31 0805 8 mm 3000 3000 1000 10 000 10 000 100
CDR32 1206 8 mm n/a 3000 1000 n/a 10 000 100
CDR33 1210 8 mm n/a 3000 1000 n/a 10 000 100
CDR02 1805 12 mm n/a 2000 500 n/a 10 000 100
CDR03 1808 12 mm n/a 2000 500 n/a 10 000 100
CDR04, CDR34 1812 12 mm n/a 1000 500 n/a 4000 100
CDR35 1825 12 mm n/a 1000 500 n/a 4000 100
CDR06 2225 12 mm n/a 1000 500 n/a 4000 100
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to + 40 °C ambient temperature and 70 % related humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 28-Mar-13 204 Document Number: 45026For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 03029www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip CapacitorsDSCC Qualified Type 03029
FEATURES• US defense supply center approved• Federal stock control number,
CAGE CODE SHV71• Small case size (0402)• Stable BP, BR and BX dielectrics• Excellent aging characteristics• Lead (Pb)-free termination code “M” • Tin/lead termination code “Z”• Wet build process• Reliable Noble Metal Electrode (NME) system• Made with a combination of design, materials and tight
process control to achieve very high field reliability• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912 Note* This datasheet provides information about parts that are
RoHS-compliant and/or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information/tables in this datasheet for details.
APPLICATIONS• Broadband wireless communication• Satellite communication• WiFi (802.11) and WiMax (802.16)• Subscriber based wireless devices• Microwave systems
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range:BP: 1.0 pF to 180 pFBR: 100 pF to 10 nFBX: 100 pF to 8.2 nF
Voltage Range: 6.3 VDC to 100 VDC
Temperature Coefficient of Capacitance (TCC):BP: 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
with zero (0) VDC appliedBP: 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
with 100 % rated VDC appliedBR: ± 15 % from -55 °C to +125 °C
with zero (0) VDC appliedBR: +15 %, -40 % from -55 °C to +125 °C
with 100 % rated VDC appliedBX: ± 15 % from -55 °C to +125 °C
with zero (0) VDC appliedBX: +15 %, -25 % from -55 °C to +125 °C
with 100 % rated VDC applied
Dissipation Factor (DF):BP:0.15 % max. at 1.0 VRMS and 1 MHz for values 1000 pF0.15 % max. at 1.0 VRMS and 1 kHz for values > 1000 pF BR, BX: 25 V: ± 3.5 % max. at 1.0 VRMS and 1 kHz 50 V: ± 2.5 % max. at 1.0 VRMS and 1 kHz
Aging Rate:BP: 0 % maximum per decadeBR, BX: 1 % maximum per decade
Insulation Resistance (IR):at +25 °C and rated voltage 100 000 M minimum or1000 F, whichever is lessat +125 °C and rated voltage 10 000 M minimum or100 F, whichever is less
Dielectric Strength Test:performed per method 103 of EIA-198-2-E.Applied test voltages 200 VDC-rated: 250 % of rated voltage
Available
Available
Revision: 09-May-14 205 Document Number: 45042For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 03029www.vishay.com Vishay Vitramon
Note• Detail ratings see selection chart
Note(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected]
Note• Metric equivalents are given for general information only
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE(V)
CAPACITANCE
MINIMUM MAXIMUM
BP 0402 100 1.0 pF 180 pF
BR 0402 50 100 pF 10 nF
BX 0402 50 100 pF 8.2 nF
ORDERING INFORMATION03029- BX 102 B J Z - T
DSCCNUMBER
DIELECTRIC CAPACITANCENOMINAL CODE
DC VOLTAGERATING (1)
CAPACITANCETOLERANCE
TERMINATION GROUP CTESTING OPTION
PACKAGING
Case code0402
BPBRBX
Expressed in picofarads (pF).
The first two digits are
significant, the third is a
multiplier. An “R” indicates a
decimal point.Examples:
1R8 = 1.8 pF101 = 100 pF
W = 6.3 VX = 10 VY = 16 VZ = 25 VA = 50 V
B = 100 V
C = ± 0.25 pF D = ± 0.5 pF
F = ± 1 % G = ± 2 % J = ± 5 %
K = ± 10 %M = ± 20 %
Note:C, D < 10 pF
(BP)F, G, J, K, M 10 pF (BP)
J, K, M (BR, BX)
M = silver palladium
Z = Ni barrier with tin/lead
plate min. 4 % lead
C = full group CL = 2000 h life
test onlyM = 1000 h life
test onlyH = low voltage
humidity test only- = no group C
testing
C = 7" reel/paper tapeO = 7" reel/flamed paper tape
J = 7" reel (low quantity)P = 11 1/4"/13" reel/paper tape
I = 11 1/4"/13" reel/flamed paper tapeB = bulk
Note: “I” and “O” are used for “M” termination code
DIMENSIONS in inches (millimeters)
PART ORDERING NUMBER
LENGTH(L)
WIDTH(W)
MAXIMUM THICKNESS
(T)
TERMINATION PAD(P)
MINIMUM MAXIMUM
03029-0.040 ± 0.004(1.02 ± 0.10)
0.020 ± 0.004(0.51 ± 0.10)
0.024(0.61)
0.004(0.10)
0.016(0.41)
LW
TMAX.
P
Revision: 09-May-14 206 Document Number: 45042For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 03029www.vishay.com Vishay Vitramon
SELECTION CHARTDIELECTRIC BP BR BX
STYLE 03029
CASE CODE 0402
VOLTAGE (VDC) 6.3 10 16 25 50 100 6.3 10 16 25 50 6.3 10 16 25 50
VOLTAGE CODE W X Y Z A B W X Y Z A W X Y Z A
CAP. CODE CAP.
1R0 1.0 pF • • • • • •
1R2 1.2 pF • • • • • •
1R5 1.5 pF • • • • • •
1R8 1.8 pF • • • • • •
2R2 2.2 pF • • • • • •
2R4 2.4 pF • • • • • •
2R7 2.7 pF • • • • • •
3R0 3.0 pF • • • • • •
3R3 3.3 pF • • • • • •
3R6 3.6 pF • • • • • •
3R9 3.9 pF • • • • • •
4R7 4.7 pF • • • • • •
5R1 5.1 pF • • • • • •
5R6 5.6 pF • • • • • •
6R2 6.2 pF • • • • • •
6R8 6.8 pF • • • • • •
7R5 7.5 pF • • • • • •
8R2 8.2 pF • • • • • •
9R1 9.1 pF • • • • • •
100 10 pF • • • • • •
110 11 pF • • • • • •
120 12 pF • • • • • •
130 13 pF • • • • • •
150 15 pF • • • • • •
160 16 pF • • • • • •
180 18 pF • • • • • •
200 20 pF • • • • • •
220 22 pF • • • • • •
240 24 pF • • • • • •
270 27 pF • • • • • •
300 30 pF • • • • • •
330 33 pF • • • • • •
360 36 pF • • • • • •
390 39 pF • • • • • •
430 43 pF • • • • • •
470 47 pF • • • • • •
510 51 pF • • • • • •
560 56 pF • • • • • •
620 62 pF • • • • • •
680 68 pF • • • • • •
750 75 pF • • • • • •
820 82 pF • • • • • •
910 91 pF • • • • • •
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “Z”Not RoHS-compliant
Revision: 09-May-14 207 Document Number: 45042For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 03029www.vishay.com Vishay Vitramon
Note(1) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”
101 100 pF • • • • • • • • • • • • • • • •121 120 pF • • • • • • • • • • • • • • • •151 150 pF • • • • • • • • • • • • • • • •181 180 pF • • • • • • • • • • • • • • • •221 220 pF • • • • • • • • • •271 270 pF • • • • • • • • • •331 330 pF • • • • • • • • • •391 390 pF • • • • • • • • • •471 470 pF • • • • • • • • • •561 560 pF • • • • • • • • • •681 680 pF • • • • • • • • • •821 820 pF • • • • • • • • • •102 1.0 nF • • • • • • • • • •122 1.2 nF • • • • • • • • • •152 1.5 nF • • • • • • • • • •182 1.8 nF • • • • • • • • •222 2.2 nF • • • • • • • • •272 2.7 nF • • • • • • • • •332 3.3 nF • • • • • • • • •392 3.9 nF • • • • • • • • •472 4.7 nF • • • • • • •562 5.6 nF • • • • • •682 6.8 nF • • • • • •822 8.2 nF • • • • • •103 10 nF • • •123 12 nF
DSCC PACKAGING QUANTITIES (1)
CASE CODE TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES BULK
PACKAGING CODE PACKAGING CODE VIAL PACKAGING CODE
“C”/“O” “J” “P”/“I” “B”
0402 8 mm 5000 1000 10 000 100
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to +40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
SELECTION CHARTDIELECTRIC BP BR BX
STYLE 03029
CASE CODE 0402
VOLTAGE (VDC) 6.3 10 16 25 50 100 6.3 10 16 25 50 6.3 10 16 25 50
VOLTAGE CODE W X Y Z A B W X Y Z A W X Y Z A
CAP. CODE CAP.
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “Z”Not RoHS-compliant
Revision: 09-May-14 208 Document Number: 45042For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 03028www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip CapacitorsDSCC Qualified Type 03028
FEATURES• US defense supply center approved• Federal stock control number,
CAGE CODE SHV71• Small case size (0603)• Stable BP, BR and BX dielectrics• Excellent aging characteristics• Lead (Pb)-free termination code “M” • Tin/lead termination code “Z”• Wet build process• Reliable Noble Metal Electrode (NME) system• Made with a combination of design, materials and tight
process control to achieve very high field reliability• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912 Note* This datasheet provides information about parts that are
RoHS-compliant and/or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information/tables in this datasheet for details.
APPLICATIONS• Broadband wireless communication• Satellite communication• WiFi (802.11) and WiMax (802.16)• Subscriber based wireless devices• Microwave systems
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range:BP: 1.0 pF to 1.0 nFBR: 100 pF to 100 nFBX: 100 pF to 100 nF
Voltage Range: 6.3 VDC to 100 VDC
Temperature Coefficient of Capacitance (TCC):BP: 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
with zero (0) VDC appliedBP: 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
with 100 % rated VDC appliedBR: ± 15 % from -55 °C to +125 °C
with zero (0) VDC appliedBR: +15 %, -40 % from -55 °C to +125 °C
with 100 % rated VDC appliedBX: ± 15 % from -55 °C to +125 °C
with zero (0) VDC appliedBX: +15 %, -25 % from -55 °C to +125 °C
with 100 % rated VDC applied
Dissipation Factor (DF):
BP:0.15 % max. at 1.0 VRMS and 1 MHz for values 1000 pF0.15 % max. at 1.0 VRMS and 1 kHz for values > 1000 pF BR, BX: 25 V: ± 3.5 % max. at 1.0 VRMS and 1 kHz 50 V: ± 2.5 % max. at 1.0 VRMS and 1 kHz
Aging Rate:BP: 0 % maximum per decadeBR, BX: 1 % maximum per decade
Insulation Resistance (IR):at +25 °C and rated voltage 100 000 M minimum or1000 F, whichever is lessat +125 °C and rated voltage 10 000 M minimum or100 F, whichever is less
Dielectric Strength Test:performed per method 103 of EIA-198-2-E.Applied test voltages 200 VDC-rated: 250 % of rated voltage
Available
Available
Revision: 09-May-14 209 Document Number: 45043For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 03028www.vishay.com Vishay Vitramon
Note• Detail ratings see selection chart
Note(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected]
Note• Metric equivalents are given for general information only
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE(V)
CAPACITANCE
MINIMUM MAXIMUM
BP 0603 100 1.0 pF 1.0 nF
BR 0603 100 100 pF 100 nF
BX 0603 100 100 pF 100 nF
ORDERING INFORMATION03028- BX 102 B J Z - T
DSCCNUMBER
DIELECTRIC CAPACITANCENOMINAL CODE
DC VOLTAGERATING (1)
CAPACITANCETOLERANCE
TERMINATION GROUP CTESTING OPTION
PACKAGING
Case code0603
BPBRBX
Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is a
multiplier. An “R”indicates a
decimal point.Examples:
1R8 = 1.8 pF101 = 100 pF
W = 6.3 VX = 10 VY = 16 VZ = 25 VA = 50 V
B = 100 V
C = ± 0.25 pF D = ± 0.5 pF
F = ± 1 % G = ± 2 % J = ± 5 %
K = ± 10 %M = ± 20 %
Note:C, D < 10 pF (BP)
F, G, J, K, M 10 pF (BP)
J, K, M (BR, BX)
M = silverpalladium
Z = Ni barrierwith tin/lead
plate min. 4 %lead
C = full group CL = 2000 h life
test onlyM = 1000 h life
test onlyH = low voltage
humidity test only
- = no group Ctesting
T = 7" reel/plastic tapeC = 7" reel/paper tape
O = 7" reel/flamed paper tapeJ = 7" reel (low quantity)
R = 11 1/4"/13" reel/plastic tapeP = 11 1/4"/13" reel/paper tape
I = 11 1/4"/13" reel/flamed paper tape
B = bulkNote:
“I” and “O” are used for “M” termination code
DIMENSIONS in inches (millimeters)
PART ORDERING NUMBER
LENGTH(L)
WIDTH(W)
MAXIMUM THICKNESS
(T)
TERMINATION PAD(P)
MINIMUM MAXIMUM
03028- 0.063 ± 0.006(1.60 ± 0.15)
0.032 ± 0.006(0.81 ± 0.15)
0.036(0.91)
0.008(0.20)
0.020(0.51)
LW
TMAX.
P
Revision: 09-May-14 210 Document Number: 45043For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 03028www.vishay.com Vishay Vitramon
SELECTION CHARTDIELECTRIC BP BR BX
STYLE 03028
CASE CODE 0603
VOLTAGE (VDC) 6.3 10 16 25 50 100 6.3 10 16 25 50 100 6.3 10 16 25 50 100
VOLTAGE CODE W X Y Z A B W X Y Z A B W X Y Z A B
CAP. CODE CAP.
1R0 1.0 pF • • • • • •
1R2 1.2 pF • • • • • •
1R5 1.5 pF • • • • • •
1R8 1.8 pF • • • • • •
2R2 2.2 pF • • • • • •
2R4 2.4 pF • • • • • •
2R7 2.7 pF • • • • • •
3R0 3.0 pF • • • • • •
3R3 3.3 pF • • • • • •
3R6 3.6 pF • • • • • •
3R9 3.9 pF • • • • • •
4R7 4.7 pF • • • • • •
5R1 5.1 pF • • • • • •
5R6 5.6 pF • • • • • •
6R2 6.2 pF • • • • • •
6R8 6.8 pF • • • • • •
7R5 7.5 pF • • • • • •
8R2 8.2 pF • • • • • •
9R1 9.1 pF • • • • • •
100 10 pF • • • • • •
110 11 pF • • • • • •
120 12 pF • • • • • •
130 13 pF • • • • • •
150 15 pF • • • • • •
160 16 pF • • • • • •
180 18 pF • • • • • •
200 20 pF • • • • • •
220 22 pF • • • • • •
240 24 pF • • • • • •
270 27 pF • • • • • •
300 30 pF • • • • • •
330 33 pF • • • • • •
360 36 pF • • • • • •
390 39 pF • • • • • •
430 43 pF • • • • • •
470 47 pF • • • • • •
510 51 pF • • • • • •
560 56 pF • • • • • •
620 62 pF • • • • • •
680 68 pF • • • • • •
750 75 pF • • • • • •
820 82 pF • • • • • •
910 91 pF • • • • • •
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “Z”Not RoHS-compliant
Revision: 09-May-14 211 Document Number: 45043For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 03028www.vishay.com Vishay Vitramon
101 100 pF • • • • • • • • • • • • • • • • • •
121 120 pF • • • • • • • • • • • • • • • • • •
151 150 pF • • • • • • • • • • • • • • • • • •
181 180 pF • • • • • • • • • • • • • • • • • •
221 220 pF • • • • • • • • • • • • • • • • • •
271 270 pF • • • • • • • • • • • • • • • • • •
331 330 pF • • • • • • • • • • • • • • • • • •
391 390 pF • • • • • • • • • • • • • • • • •
471 470 pF • • • • • • • • • • • • • • • • •
561 560 pF • • • • • • • • • • • • • • • • •
681 680 pF • • • • • • • • • • • • • • • • •
821 820 pF • • • • • • • • • • • • • • • •
102 1.0 nF • • • • • • • • • • • • • • • •
122 1.2 nF • • • • • • • • • • • •
152 1.5 nF • • • • • • • • • • • •
182 1.8 nF • • • • • • • • • • • •
222 2.2 nF • • • • • • • • • • • •
272 2.7 nF • • • • • • • • • • • •
332 3.3 nF • • • • • • • • • • •
392 3.9 nF • • • • • • • • • • •
472 4.7 nF • • • • • • • • • • •
562 5.6 nF • • • • • • • • • • •
682 6.8 nF • • • • • • • • • • •
822 8.2 nF • • • • • • • • • • •
103 10 nF • • • • • • • • • •
123 12 nF • • • • • • • • •
153 15 nF • • • • • • • • •
183 18 nF • • • • • • • • •
223 22 nF • • • • • • • • •
273 27 nF • • • • • • • • •
333 33 nF • • • • • • •
393 39 nF • • • • • • •
473 47 nF • • • • • • •
563 56 nF • • • • • • •
683 68 nF • • • •
823 82 nF • • • •
104 100 nF • • • •
124 120 nF
154 150 nF
184 180 nF
224 220 nF
SELECTION CHARTDIELECTRIC BP BR BX
STYLE 03028
CASE CODE 0603
VOLTAGE (VDC) 6.3 10 16 25 50 100 6.3 10 16 25 50 100 6.3 10 16 25 50 100
VOLTAGE CODE W X Y Z A B W X Y Z A B W X Y Z A B
CAP. CODE CAP.
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “Z”Not RoHS-compliant
Revision: 09-May-14 212 Document Number: 45043For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 03028www.vishay.com Vishay Vitramon
Note(1) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”
DSCC PACKAGING QUANTITIES (1)
CASE CODE TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES BULK
PACKAGING CODE PACKAGING CODE VIAL PACKAGING CODE
“C”/“O”/“T” “J” “P”/“I”/“R” “B”
0603 8 mm 4000 1000 10 000 100
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to +40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 09-May-14 213 Document Number: 45043For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05006www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip CapacitorsDSCC Qualified Type 05006
FEATURES• US defense supply center approved• Federal stock control number,
CAGE CODE SHV71• Case size 0805• Stable BP, BR and BX dielectrics• Excellent aging characteristics• Lead (Pb)-free termination code “M” • Tin/lead termination code “Z” and “U”• Wet build process• Reliable Noble Metal Electrode (NME) system• Made with a combination of design, materials and tight
process control to achieve very high field reliability• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912 Note* This datasheet provides information about parts that are
RoHS-compliant and/or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information/tables in this datasheet for details.
APPLICATIONS• Avionic application• Sonar applications• Satellite systems• Missiles applications• Geographical information systems• Global positioning systems
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range:BP: 1.0 pF to 3.3 nFBR: 100 pF to 220 nFBX: 100 pF to 180 nF
Voltage Range: 10 VDC to 200 VDC
Temperature Coefficient of Capacitance (TCC):BP: 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
with zero (0) VDC appliedBP: 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
with 100 % rated VDC appliedBR: ± 15 % from -55 °C to +125 °C
with zero (0) VDC appliedBR: +15 %, -40 % from -55 °C to +125 °C
with 100 % rated VDC appliedBX: ± 15 % from -55 °C to +125 °C
with zero (0) VDC appliedBX: +15 %, -25 % from -55 °C to +125 °C
with 100 % rated VDC applied
Dissipation Factor (DF):BP:0.15 % max. at 1.0 VRMS and 1 MHz for values 1000 pF0.15 % max. at 1.0 VRMS and 1 kHz for values > 1000 pF
BR and BX: 25 V: 3.5 % max. at 1.0 VRMS and 1 kHz 50 V: 2.5 % max. at 1.0 VRMS and 1 kHz
Aging Rate:BP: 0 % maximum per decadeBR, BX: 1 % maximum per decade
Insulation Resistance (IR):at +25 °C and rated voltage 100 000 M minimum or1000 F, whichever is lessat +125 °C and rated voltage 10 000 M minimum or100 F, whichever is less
Dielectric Strength Test:performed per method 103 of EIA-198-2-E.Applied test voltages 200 VDC-rated: 250 % of rated voltage
Available
Available
Revision: 09-May-14 214 Document Number: 45048For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05006www.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
Notes(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected](2) “U” termination part number code for DSCC product length, width and thickness dimensions positive tolerances (including bandwidth) above
are allowed to increase by the following amounts: length 0.020" (0.51 mm), width/thickness 0.015" (0.38 mm)
Note• Metric equivalents are given for general information only
QUICK REFERENCE DATA
DIELECTRIC CASEMAXIMUM VOLTAGE
(V)
CAPACITANCE
MINIMUM MAXIMUM
BP 0805 200 1.0 pF 3.3 nF
BR 0805 100 100 pF 220 nF
BX 0805 100 100 pF 180 nF
ORDERING INFORMATION05006- BP 101 B J X - T
DSCCNUMBER
DIELECTRIC CAPACITANCENOMINAL CODE
DC VOLTAGERATING (1)
CAPACITANCETOLERANCE
TERMINATION GROUP C TESTINGOPTION (2)
PACKAGING
Case code0805
BPBRBX
Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is a
multiplier. An “R”indicates a
decimal point.Examples:
1R8 = 1.8 pF101 = 100 pF
X = 10 VY = 16 VZ = 25 VA = 50 V
B = 100 VC = 200 V
C = ± 0.25 pFD = ± 0.5 pF
F = ± 1 % G = ± 2 %J = ± 5 %
K = ± 10 %M = ± 20 %
Note:C, D < 10 pF (BP)
F, G, J, K, M 10 pF (BP)
J, K, M (BR, BX)
M = silverpalladium
Z = Ni barrierwith tin/lead
plate min. 4 %lead
U (2) = hot solder
dipped(min. 4 % lead)
C = full group CL = 2000 h life
test onlyM = 1000 h life
test onlyH = low voltage
humidity test only
- = no group Ctesting
T = 7" reel/plastic tapeC = 7" reel/paper tape
O = 7" reel/flamed paper tapeJ = 7" reel (low quantity)
R = 11 1/4"/13" reel/plastic tapeP = 11 1/4"/13" reel/paper tape
I = 11 1/4"/13" reel/flamedpaper tape
B = bulkNote: “I” and “O” are used for
“M” termination code
DIMENSIONS in inches (millimeters)
PART ORDERING NUMBER
LENGTH(L)
WIDTH(W)
MAXIMUM THICKNESS
(T)
TERMINATION PAD(P)
MINIMUM MAXIMUM
05006-0.080 ± 0.008(2.03 ± 0.20)
0.050 ± 0.008(1.27 ± 0.20)
0.055(1.40)
0.012(0.30)
0.028(0.71)
LW
TMAX.
P
Revision: 09-May-14 215 Document Number: 45048For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05006www.vishay.com Vishay Vitramon
SELECTION CHARTDIELECTRIC BP BR BX STYLE 05006CASE CODE 0805VOLTAGE (VDC) 10 16 25 50 100 200 10 16 25 50 100 10 16 25 50 100VOLTAGE CODE X Y Z A B C X Y Z A B X Y Z A BCAP. CODE CAP.
1R0 1.0 pF • • • • + •1R2 1.2 pF • • • • + •1R5 1.5 pF • • • • + •1R8 1.8 pF • • • • + •2R2 2.2 pF • • • • + •2R7 2.7 pF • • • • + •3R3 3.3 pF • • • • + •3R9 3.9 pF • • • • + •4R7 4.7 pF • • • • + •5R6 5.6 pF • • • • + •6R8 6.8 pF • • • • + •8R2 8.2 pF • • • • + •100 10 pF • • • • + •120 12 pF • • • • + •150 15 pF • • • • + •180 18 pF • • • • + •220 22 pF • • • • + •270 27 pF • • • • + •330 33 pF • • • • + •390 39 pF • • • • + •470 47 pF • • • • + •560 56 pF • • • • + •680 68 pF • • • • + •820 82 pF • • • • + •101 100 pF • • • • + • • • • • • • • • • •121 120 pF • • • • + • • • • • • • • • • +151 150 pF • • • • + • • • • • • • • • • +181 180 pF • • • • + • • • • • • • • • • +221 220 pF • • • • + • • • • • • • • • • +271 270 pF • • • • + • • • • • • • • • • +331 330 pF • • • • + • • • • • • • • • • +391 390 pF • • • • + • • • • • • • • • • +471 470 pF • • • • + • • • • • • • • • • +561 560 pF • • • + • • • • • • • • • • • +681 680 pF • • • + • • • • • • • • • • • +821 820 pF • • • • • • • • • • • • • • • +102 1.0 nF • • • • • • • • • • • • • • +122 1.2 nF • • • • • • • • • • • • • • +152 1.5 nF • • • • • • • • • • • • • • +182 1.8 nF • • • • • • • • • • • • • +222 2.2 nF • • • • • • • • • • • • • +272 2.7 nF • • • • • • • • • • • • +332 3.3 nF • • • • • • • • • • • +392 3.9 nF • • • • • • • • + +472 4.7 nF • • • • • • • • + +562 5.6 nF • • • • • • • • + •682 6.8 nF • • • • • • • • + •822 8.2 nF • • • • • • • • + •
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
+ Use MIL-PRF-55681 (CDR) instead, part numbers removed from DSCC listing
Revision: 09-May-14 216 Document Number: 45048For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05006www.vishay.com Vishay Vitramon
Notes(1) Vishay Vitramon uses embossed plastic carrier tape and punch paper carrier tape(2) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”
103 10 nF • • • • • • • • + •123 12 nF • • • • • • • • +153 15 nF • • • • • • • • +183 18 nF • • • • • • • • +223 22 nF • • • • • • • • •273 27 nF • • • • • • • • •333 33 nF • • • • • • • •393 39 nF • • • • • • •473 47 nF • • • • • • •563 56 nF • • • • • • •683 68 nF • • • • • • •823 82 nF • • • • • • •104 100 nF • • • • • • •124 120 nF • • •154 150 nF • • •184 180 nF • •224 220 nF • •274 270 nF334 330 nF394 390 nF474 470 nF564 560 nF684 680 nF824 820 nF105 1.0 μF
DSCC PACKAGING QUANTITIES (1)(2)
CASE CODE TAPE SIZE7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES BULK PACKAGING CODE PACKAGING CODE VIAL PACKAGING CODE
“C”/”O”/“T” “J” “P”/“I”/”R” “B”0805 8 mm 3000 1000 10 000 100
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to +40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
SELECTION CHARTDIELECTRIC BP BR BX STYLE 05006CASE CODE 0805VOLTAGE (VDC) 10 16 25 50 100 200 10 16 25 50 100 10 16 25 50 100VOLTAGE CODE X Y Z A B C X Y Z A B X Y Z A BCAP. CODE CAP.
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
+ Use MIL-PRF-55681 (CDR) instead, part numbers removed from DSCC listing
Revision: 09-May-14 217 Document Number: 45048For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05007www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip CapacitorsDSCC Qualified Type 05007
FEATURES• US defense supply center approved• Federal stock control number,
CAGE CODE SHV71• Case size 1206• Stable BP, BR and BX dielectrics• Excellent aging characteristics• Tin/lead termination code “Z” and “U”• Lead (Pb)-free termination code “M” • Wet build process• Reliable Noble Metal Electrode (NME) system• Made with a combination of design, materials and tight
process control to achieve very high field reliability• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912 Note* This datasheet provides information about parts that are
RoHS-compliant and/or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information/tables in this datasheet for details.
APPLICATIONS• Avionic application• Sonar applications• Satellite systems• Missiles applications• Geographical information systems• Global positioning systems
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at +25 °C unless otherwise specified
Operating Temperature: -55 °C to +125 °C
Capacitance Range:BP: 1.0 pF to 6.8 nFBR: 820 pF to 560 nFBX: 820 pF to 470 nF
Voltage Range: 16 VDC to 200 VDC
Temperature Coefficient of Capacitance (TCC):BP: 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
with zero (0) VDC appliedBP: 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C
with 100 % rated VDC appliedBR: ± 15 % from -55 °C to +125 °C
with zero (0) VDC appliedBR: +15 %, -40 % from -55 °C to +125 °C
with 100 % rated VDC appliedBX: ± 15 % from -55 °C to +125 °C
with zero (0) VDC appliedBX: +15 %, -25 % from -55 °C to +125 °C
with 100 % rated VDC applied
Dissipation Factor (DF):BP:0.15 % max. at 1.0 VRMS and 1 MHz for values 1000 pF0.15 % max. at 1.0 VRMS and 1 kHz for values > 1000 pF BR and BX: 25 V: 3.5 % max. at 1.0 VRMS and 1 kHz 50 V: 2.5 % max. at 1.0 VRMS and 1 kHz
Aging Rate:BP: 0 % maximum per decadeBR, BX: 1 % maximum per decade
Insulation Resistance (IR):at +25 °C and rated voltage 100 000 M minimum or1000 F, whichever is lessat +125 °C and rated voltage 10 000 M minimum or100 F, whichever is less
Dielectric Strength Test:performed per method 103 of EIA-198-2-E.Applied test voltages 200 VDC-rated: 250 % of rated voltage
Available
Available
Revision: 13-Aug-14 218 Document Number: 45049For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05007www.vishay.com Vishay Vitramon
Note• Detail ratings see “Selection Chart”
Notes(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected](2) “U” termination part number code for DSCC product length, width and thickness dimensions positive tolerances (including bandwidth) above
are allowed to increase by the following amounts: length 0.025" (0.64 mm), width/thickness 0.015" (0.38 mm)
Note• Metric equivalents are given for general information only
QUICK REFERENCE DATA
DIELECTRIC CASEMAXIMUM VOLTAGE
(V)
CAPACITANCE
MINIMUM MAXIMUM
BP 1206 200 1.0 pF 6.8 nF
BR 1206 100 820 pF 560 nF
BX 1206 100 820 pF 470 nF
ORDERING INFORMATION05007- BP 101 B J X - T
DSCCNUMBER
DIELECTRIC CAPACITANCENOMINAL CODE
DC VOLTAGERATING (1)
CAPACITANCETOLERANCE
TERMINATION GROUP C TESTING OPTION (2)
PACKAGING
Case code1206
BPBRBX
Expressed inpicofarads (pF).
The first twodigits are
significant, thethird is a
multiplier. An “R”indicates a
decimal point.Examples:
1R8 = 1.8 pF101 = 100 pF
X = 10 VY = 16 VZ = 25 VA = 50 V
B = 100 VC = 200 V
C = ± 0.25 pF D = ± 0.5 pF
F = ± 1 % G = ± 2 %J = ± 5 %
K = ± 10 %M = ± 20 %
Note:C, D < 10 pF (BP)
F, G, J, K, M 10 pF (BP)
J, K, M (BR, BX)
M = silverpalladium
Z = Ni barrierwith tin/lead
plate min. 4 %lead
U (2) = hot solder
dipped(min. 4 % lead)
C = full group CL = 2000 h life
test onlyM = 1000 h life
test onlyH = low voltage
humidity test only- = no group C
testing
T = 7" reel/plastic tapeJ = 7" reel (low quantity)
R = 11 1/4" reel/plastic tapeB = bulk
DIMENSIONS in inches (millimeters)
PART ORDERING NUMBER
LENGTH (L)
WIDTH(W)
MAXIMUM THICKNESS
(T)
TERMINATION PAD(P)
MINIMUM MAXIMUM
05007-0.125 ± 0.008(3.18 ± 0.20)
0.062 ± 0.008(1.57 ± 0.20)
0.059(1.50)
0.010(0.25)
0.030(0.76)
LW
TMAX.
P
Revision: 13-Aug-14 219 Document Number: 45049For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05007www.vishay.com Vishay Vitramon
SELECTION CHARTDIELECTRIC BP BR BXSTYLE 05007CASE CODE 1206VOLTAGE (VDC) 16 25 50 100 200 10 16 25 50 100 10 16 25 50 100VOLTAGE CODE Y Z A B C X Y Z A B X Y Z A B CAP. CODE CAP.
1R0 1.0 pF • • • + •1R2 1.2 pF • • • + •1R5 1.5 pF • • • + •1R8 1.8 pF • • • + •2R2 2.2 pF • • • + •2R7 2.7 pF • • • + •3R3 3.3 pF • • • + •3R9 3.9 pF • • • + •4R7 4.7 pF • • • + •5R6 5.6 pF • • • + •6R8 6.8 pF • • • + •8R2 8.2 pF • • • + •100 10 pF • • • + •120 12 pF • • • + •150 15 pF • • • + •180 18 pF • • • + •220 22 pF • • • + •270 27 pF • • • + •330 33 pF • • • + •390 39 pF • • • + •470 47 pF • • • + •560 56 pF • • • + •680 68 pF • • • + •820 82 pF • • • + •101 100 pF • • • + •121 120 pF • • • + •151 150 pF • • • + •181 180 pF • • • + •221 220 pF • • • + •271 270 pF • • • + •331 330 pF • • • + •391 390 pF • • • + •471 470 pF • • • + •561 560 pF • • • + •681 680 pF • • • + •821 820 pF • • • + • • • • • • • • • • •102 1.0 nF • • • + • • • • • • • • • • •122 1.2 nF • • + • • • • • • • • • • • •152 1.5 nF • • + • • • • • • • • • • • •182 1.8 nF • • + • • • • • • • • • • • •222 2.2 nF • • + • • • • • • • • • • • •272 2.7 nF • • • • • • • • • • • • • • •332 3.3 nF • • • • • • • • • • • • • •392 3.9 nF • • • • • • • • • • • • • •472 4.7 nF • • • • • • • • • • • • • +562 5.6 nF • • • • • • • • • • • • +682 6.8 nF • • • • • • • • • • • • +822 8.2 nF • • • • • • • • • +
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
+ Use MIL-PRF-55681 (CDR) instead, part numbers removed from DSCC listing
Revision: 13-Aug-14 220 Document Number: 45049For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05007www.vishay.com Vishay Vitramon
Notes(1) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”(2) Packaging quantities can depend from product thickness
103 10 nF • • • • • • • • • +123 12 nF • • • • • • • • • +153 15 nF • • • • • • • • • +183 18 nF • • • • • • • • + •223 22 nF • • • • • • • • + •273 27 nF • • • • • • • • +333 33 nF • • • • • • • • +393 39 nF • • • • • • • • +473 47 nF • • • • • • • • •563 56 nF • • • • • • • • •683 68 nF • • • • • • • •823 82 nF • • • • • • • •104 100 nF • • • • • • • •124 120 nF • • • • • • •154 150 nF • • • • • • •184 180 nF • • • • • • •204 200 nF • • • • • • •224 220 nF • • • • • • •254 250 nF • • • • • •274 270 nF • • • • •334 330 nF • • • • •394 390 nF • • • • •474 470 nF • • • •564 560 nF • •684 680 nF824 820 nF105 1.0 μF
DSCC PACKAGING QUANTITIES (1)
CASE CODE TAPE SIZE7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES BULK PACKAGING CODE PACKAGING CODE VIAL PACKAGING CODE “T” “J” “R” “B”
1206 (2) 8 mm 3000/2500 1000 10 000/9000 100
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to +40 °C ambient temperature and 70 % relative humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
SELECTION CHARTDIELECTRIC BP BR BXSTYLE 05007CASE CODE 1206VOLTAGE (VDC) 16 25 50 100 200 10 16 25 50 100 10 16 25 50 100VOLTAGE CODE Y Z A B C X Y Z A B X Y Z A B CAP. CODE CAP.
NotesRoHS-compliant except when supplied with lead (Pb)-containing terminations, codes “Z” and “U”Not RoHS-compliant
+ Use MIL-PRF-55681 (CDR) instead, part numbers removed from DSCC listing
Revision: 13-Aug-14 221 Document Number: 45049For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05001www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip CapacitorsHigh Frequency DSCC Qualified Type 05001
FEATURES• US Defense Supply Center approved
• Federal stock control number,CAGE CODE SHV71
• Case size 0805
• High frequency
• Excellent aging characteristics
• Tin/lead termination code “Z”
• Lead (Pb)-free terminations code “M”
• Surface mount, wet build process
• Reliable Noble Metal Electrode (NME) system
• Made with a combination of design, materials and tightprocess control to achieve very high field reliability
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
Note* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information / tables in this datasheet for details.
APPLICATIONS• Broadband wireless communication
• Satellite communication
• WiFi (802.11) and WiMax (802.16)
• VolP networks and cellular base stations
• Subscriber based wireless devices
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at 25 °C unless otherwise specified
Operating Temperature: - 55 °C to + 125 °C
Capacitance Range: 1.0 pF to 100 pF
Voltage Rating: 50 VDC to 250 VDC
Temperature Coefficient of Capacitance (TCC):
BP: 0 ppm/°C ± 30 ppm/°C from - 55 °C to + 125 °C withzero (0) VDC applied
Dissipation Factor (DF):BP: 0.05 % max. at 1.0 VRMS and 1 MHz
Aging Rate: 0 % maximum per decade
Insulation Resistance (IR):At + 25 °C and rated voltage 100 000 M minimum or1000 F, whichever is lessAt + 125 °C and rated voltage 10 000 M minimum or100 F, whichever is less
Dielectric Strength Test:
Performed per method 103 of EIA-198-2-E.
Applied test voltages 250 VDC-rated: 200 % of rated voltage
Available
Available
Revision: 26-Mar-13 222 Document Number: 45068For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05001www.vishay.com Vishay Vitramon
Notes(1) DC voltage rating should not be exceeded in application(2) Selecting one of the group C options with life testing may extend the delivery time
QUICK REFERENCE DATA
DIELECTRIC CASE CODEMAXIMUM VOLTAGE
(V)
CAPACITANCE
MINIMUM MAXIMUM
BP 0805 250 1.0 pF 100 pF
ORDERING INFORMATION05001- 1R0 B C Z - C
DSCCNUMBER
CAPACITANCENOMINAL CODE
DC VOLTAGERATING (1)
CAPACITANCETOLERANCE
TERMINATION GROUP CTESTING OPTION (2)
PACKAGING
0805Case size
HighFrequency
Expressed inpicofarads (pF).
The first two digitsare significant, thethird is a multiplier.
An “R” indicatesa decimal point.
Examples:1R0 = 1.0 pF
A = 50 VB = 100 VC = 200 VK = 250 V
B = ± 0.10 pF C = ± 0.25 pF D = ± 0.50 pF
F = ± 1 %G = ± 2 % J = ± 5 %
K = ± 10 %M = ± 20 %
Note: B, C, D 6.2 pF
B, C, J, K, M6.8 pF to 9.1 pF
F, G, J, K, M 10 pF
M = Silver palladiumZ = Ni barrier with
tin/lead plate min. 4 % lead
C = Full group CL = 2000 h life test onlyM = 1000 h life test only
H = Low voltage humiditytest only
- = No group C testing
T = 7" reel/plastic tapeC = 7" reel/paper tape
O = 7" reel/flamed paper tapeJ = 7" reel (low quantity)
R = 11 1/4"/13" reel/plastic tapeP = 11 1/4"/13" reel/paper tape
I = 11 1/4"/13" reel/flamed paper tapeB = Bulk
Note:“I” and “O” is used for “M”
termination code
DIMENSIONS in inches (millimeters)
PART ORDERING NUMBER
LENGTH(L)
WIDTH(W)
MAXIMUM THICKNESS(T)
TERMINATIONS PAD (P)
MINIMUM MAXIMUM
05001- 0.079 ± 0.008(2.00 ± 0.20)
0.049 ± 0.008(1.25 ± 0.20)
0.055(1.40)
0.010(0.25)
0.030(0.76)
LW
TMAX.
P
Revision: 26-Mar-13 223 Document Number: 45068For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05001www.vishay.com Vishay Vitramon
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “Z”
•• Paper carrier • Plastic carrier tape
SELECTION CHARTDIELECTRIC BPSTYLE 05001
TOLERANCECASE CODE 0805VOLTAGE (VDC) 50 100 200 250VOLTAGE CODE A B C K
CAP. CODE CAP.1R0 1.0 pF •• •• •• •• B, C1R1 1.1 pF •• •• •• •• B, C, D1R2 1.2 pF •• •• •• •• B, C, D1R3 1.3 pF •• •• •• •• B, C, D1R4 1.4 pF •• •• •• •• B, C, D1R5 1.5 pF •• •• •• •• B, C, D1R6 1.6 pF •• •• •• •• B, C, D1R7 1.7 pF •• •• •• •• B, C, D1R8 1.8 pF •• •• •• •• B, C, D1R9 1.9 pF •• •• •• •• B, C, D2R0 2.0 pF •• •• •• •• B, C, D2R1 2.1 pF •• •• •• •• B, C, D2R2 2.2 pF •• •• •• •• B, C, D2R4 2.4 pF •• •• •• •• B, C, D2R7 2.7 pF •• •• •• •• B, C, D3R0 3.0 pF •• •• •• •• B, C, D3R3 3.3 pF •• •• •• •• B, C, D3R6 3.6 pF •• •• •• •• B, C, D3R9 3.9 pF •• •• •• •• B, C, D4R3 4.3 pF •• •• •• •• B, C, D4R7 4.7 pF •• •• •• •• B, C, D5R1 5.1 pF •• •• •• •• B, C, D5R6 5.6 pF •• •• •• •• B, C, D6R2 6.2 pF •• •• •• •• B, C, D6R8 6.8 pF •• •• •• •• B, C, J, K, M7R5 7.5 pF •• •• •• •• B, C, J, K, M8R2 8.2 pF •• •• •• •• B, C, J, K, M9R1 9.1 pF •• •• •• •• B, C, J, K, M100 10 pF •• •• •• •• F, G, J, K, M110 11 pF •• •• •• •• F, G, J, K, M120 12 pF •• •• •• •• F, G, J, K, M130 13 pF •• •• •• •• F, G, J, K, M150 15 pF •• •• •• •• F, G, J, K, M180 18 pF •• •• •• •• F, G, J, K, M200 20 pF •• •• •• •• F, G, J, K, M220 22 pF •• •• •• •• F, G, J, K, M240 24 pF •• •• •• •• F, G, J, K, M270 27 pF •• •• •• •• F, G, J, K, M300 30 pF •• •• •• •• F, G, J, K, M330 33 pF •• •• •• •• F, G, J, K, M360 36 pF •• •• •• •• F, G, J, K, M390 39 pF •• •• •• •• F, G, J, K, M430 43 pF •• •• •• •• F, G, J, K, M470 47 pF •• •• •• •• F, G, J, K, M510 51 pF •• •• •• •• F, G, J, K, M560 56 pF •• •• •• •• F, G, J, K, M620 62 pF •• •• • • F, G, J, K, M680 68 pF •• •• • • F, G, J, K, M750 75 pF •• •• • • F, G, J, K, M820 82 pF •• •• • • F, G, J, K, M910 91 pF •• •• • • F, G, J, K, M101 100 pF •• •• • • F, G, J, K, M
Revision: 26-Mar-13 224 Document Number: 45068For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05001www.vishay.com Vishay Vitramon
Note(1) Reference: EIA Standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”
DSCC PACKAGING QUANTITIES (1)
CASECODE
TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES BULK
PACKAGING CODE “C”/“O”/“T”
PACKAGING CODE“J”
PACKAGING CODE “P”/“I”/“R”
VIAL PACKAGING CODE“B”
0805 8 mm 3000 1000 10 000 100
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to + 40 °C ambient temperature and 70 % related humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 26-Mar-13 225 Document Number: 45068For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05002www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip CapacitorsHigh Frequency DSCC Qualified Type 05002
FEATURES• US Defense Supply Center approved
• Federal stock control number,CAGE CODE SHV71
• Case size 0603
• High frequency
• Excellent aging characteristics
• Tin/lead termination code “Z”
• Lead (Pb)-free terminations code “M”
• Surface mount, wet build process
• Reliable Noble Metal Electrode (NME) system
• Made with a combination of design, materials and tightprocess control to achieve very high field reliability
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
Note* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information / tables in this datasheet for details.
APPLICATIONS• Broadband wireless communication
• Satellite communication
• WiFi (802.11) and WiMax (802.16)
• VolP networks and cellular base stations
• Subscriber based wireless devices
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at 25 °C unless otherwise specified
Operating Temperature: - 55 °C to + 125 °C
Capacitance Range: 1.0 pF to 100 pF
Voltage Rating: 50 VDC to 250 VDC
Temperature Coefficient of Capacitance (TCC):
BP: 0 ppm/°C ± 30 ppm/°C from - 55 °C to + 125 °C withzero (0) VDC applied
Dissipation Factor (DF):
BP: 0.05 % max. at 1.0 VRMS and 1 MHz
Aging Rate: 0 % maximum per decade
Insulation Resistance (IR):
At + 25 °C and rated voltage 100 000 M minimum or1000 F, whichever is less
At + 125 °C and rated voltage 10 000 M minimum or100 F, whichever is less
Dielectric Strength Test:
Performed per method 103 of EIA-198-2-E.
Applied test voltages 250 VDC-rated: 200 % of rated voltage
Available
Available
Revision: 27-Mar-13 226 Document Number: 45069For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05002www.vishay.com Vishay Vitramon
Notes(1) DC voltage rating should not be exceeded in application(2) Selecting one of the group C options with life testing may extend the delivery time
QUICK REFERENCE DATA
DIELECTRIC CASE CODEMAXIMUM VOLTAGE
(V)
CAPACITANCE
MINIMUM MAXIMUM
BP 0603 250 1.0 pF 100 pF
ORDERING INFORMATION05002- 1R0 B F Z - C
DSCCNUMBER
CAPACITANCENOMINAL CODE
DC VOLTAGERATING (1)
CAPACITANCETOLERANCE
TERMINATION GROUP C (2)
TESTING OPTIONPACKAGING
0603Case size
HighFrequency
Expressed inpicofarads (pF).
The first two digitsare significant, thethird is a multiplier.An “R” indicates a
decimal point.Examples:
1R0 = 1.0 pF
A = 50 VB = 100 VC = 200 VK = 250 V
B = ± 0.10 pF C = ± 0.25 pF D = ± 0.50 pF
F = ± 1 %G = ± 2 % J = ± 5 %
K = ± 10 %M = ± 20 %
Note: B, C, D 6.2 pF
B, C, J, K, M 6.8 pF to 9.1 pF
F, G, J, K, M 10 pF
M = Silver palladiumZ = Ni barrier with
tin/lead plate min. 4 % lead
C = Full group CL = 2000 h life test onlyM = 1000 h life test only
H = Low voltagehumidity test only
- = Group A test only
C = 7" reel/paper tapeO = 7" reel/flamed paper tape
J = 7" reel (low quantity)P = 11 1/4"/13" reel/paper tape
I = 11 1/4"/13" reel/flamed paper tapeB = Bulk
Note:“I” and “O” is used for “M”
termination code
DIMENSIONS in inches (millimeters)
PART ORDERING NUMBER
LENGTH(L)
WIDTH (W)
MAXIMUM THICKNESS (T)
TERMINATIONS PAD (P)
MINIMUM MAXIMUM
05002- 0.063 ± 0.006(1.60 ± 0.15)
0.032 ± 0.006(0.81 ± 0.15)
0.036(0.91)
0.008(0.20)
0.020(0.50)
LW
TMAX.
P
Revision: 27-Mar-13 227 Document Number: 45069For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05002www.vishay.com Vishay Vitramon
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “Z”
•• Paper carrier tape
SELECTION CHARTDIELECTRIC BPSTYLE 05002
TOLERANCECASE CODE 0603VOLTAGE (VDC) 50 100 200 250VOLTAGE CODE A B C K
CAP. CODE CAP.1R0 1.0 pF •• •• •• •• B, C1R1 1.1 pF •• •• •• •• B, C, D1R2 1.2 pF •• •• •• •• B, C, D1R3 1.3 pF •• •• •• •• B, C, D1R4 1.4 pF •• •• •• •• B, C, D1R5 1.5 pF •• •• •• •• B, C, D1R6 1.6 pF •• •• •• •• B, C, D1R7 1.7 pF •• •• •• •• B, C, D1R8 1.8 pF •• •• •• •• B, C, D1R9 1.9 pF •• •• •• •• B, C, D2R0 2.0 pF •• •• •• •• B, C, D2R1 2.1 pF •• •• •• •• B, C, D2R2 2.2 pF •• •• •• •• B, C, D2R4 2.4 pF •• •• •• •• B, C, D2R7 2.7 pF •• •• •• •• B, C, D3R0 3.0 pF •• •• •• •• B, C, D3R3 3.3 pF •• •• •• •• B, C, D3R6 3.6 pF •• •• •• •• B, C, D3R9 3.9 pF •• •• •• •• B, C, D4R3 4.3 pF •• •• •• •• B, C, D4R7 4.7 pF •• •• •• •• B, C, D5R1 5.1 pF •• •• •• •• B, C, D5R6 5.6 pF •• •• •• •• B, C, D6R2 6.2 pF •• •• •• •• B, C, D6R8 6.8 pF •• •• •• •• B, C, J, K, M7R5 7.5 pF •• •• •• •• B, C, J, K, M8R2 8.2 pF •• •• •• •• B, C, J, K, M9R1 9.1 pF •• •• •• •• B, C, J, K, M100 10 pF •• •• •• •• F, G, J, K, M110 11 pF •• •• •• •• F, G, J, K, M120 12 pF •• •• •• •• F, G, J, K, M130 13 pF •• •• •• •• F, G, J, K, M150 15 pF •• •• •• •• F, G, J, K, M180 18 pF •• •• •• •• F, G, J, K, M200 20 pF •• •• •• •• F, G, J, K, M220 22 pF •• •• •• •• F, G, J, K, M240 24 pF •• •• •• •• F, G, J, K, M270 27 pF •• •• •• •• F, G, J, K, M300 30 pF •• •• •• •• F, G, J, K, M330 33 pF •• •• •• •• F, G, J, K, M360 36 pF •• •• •• •• F, G, J, K, M390 39 pF •• •• •• •• F, G, J, K, M430 43 pF •• •• •• •• F, G, J, K, M470 47 pF •• •• •• •• F, G, J, K, M510 51 pF •• •• F, G, J, K, M560 56 pF •• •• F, G, J, K, M620 62 pF •• •• F, G, J, K, M680 68 pF •• •• F, G, J, K, M750 75 pF •• F, G, J, K, M820 82 pF •• F, G, J, K, M910 91 pF •• F, G, J, K, M101 100 pF •• F, G, J, K, M
Revision: 27-Mar-13 228 Document Number: 45069For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05002www.vishay.com Vishay Vitramon
Note(1) Reference: EIA Standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”
DSCC PACKAGING QUANTITIES (1)
CASECODE
TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES BULK
PACKAGING CODE“C”/”O”
PACKAGING CODE“J”
PACKAGING CODE “P”/”I”
VIAL PACKAGING CODE“B”
0603 8 mm 4000 1000 10 000 100
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to + 40 °C ambient temperature and 70 % related humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 27-Mar-13 229 Document Number: 45069For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05003www.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip CapacitorsHigh Frequency DSCC Qualified Type 05003
FEATURES• US Defense Supply Center approved
• Federal stock control number,CAGE CODE SHV71
• Case size 0402
• High frequency
• Excellent aging characteristics
• Tin/lead termination code “Z”
• Lead (Pb)-free terminations code “M”
• Surface mount, wet build process
• Reliable Noble Metal Electrode (NME) system
• Made with a combination of design, materials and tightprocess control to achieve very high field reliability
• Material categorization: for definitions of complianceplease see www.vishay.com/doc?99912
Note* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. Forexample, parts with lead (Pb) terminations are not RoHS-compliant.Please see the information / tables in this datasheet for details.
APPLICATIONS• Broadband wireless communication
• Satellite communication
• WiFi (802.11) and WiMax (802.16)
• VolP networks and cellular base stations
• Subscriber based wireless devices
ELECTRICAL SPECIFICATIONSNote• Electrical characteristics at 25 °C unless otherwise specified
Operating Temperature: - 55 °C to + 125 °C
Capacitance Range: 1.0 pF to 27 pF
Voltage Rating: 50 VDC to 100 VDC
Temperature Coefficient of Capacitance (TCC):
BP: 0 ppm/°C ± 30 ppm/°C from - 55 °C to + 125 °C withzero (0) VDC applied
Dissipation Factor (DF):
BP: 0.05 % max. at 1.0 VRMS and 1 MHz
Aging Rate: 0 % maximum per decade
Insulation Resistance (IR):
At + 25 °C and rated voltage 100 000 M minimum or1000 F, whichever is less
At + 125 °C and rated voltage 10 000 M minimum or100 F, whichever is less
Dielectric Strength Test:Performed per method 103 of EIA-198-2-E.Applied test voltages 250 VDC-rated: 200 % of rated voltage
Available
Available
Revision: 27-Mar-13 230 Document Number: 45070For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05003www.vishay.com Vishay Vitramon
Notes(1) DC voltage rating should not be exceeded in application(2) Selecting one of the group C options with life testing may extend the delivery time
QUICK REFERENCE DATA
DIELECTRIC CASE CODEMAXIMUM VOLTAGE
(V)
CAPACITANCE
MINIMUM MAXIMUM
BP 0402 100 1.0 pF 27 pF
ORDERING INFORMATION05003- 1R0 B C Z - C
DSCCNUMBER
CAPACITANCENOMINAL CODE
DC VOLTAGERATING (1)
CAPACITANCETOLERANCE
TERMINATION GROUP C (2)
TESTING OPTIONPACKAGING
0603Case size
HighFrequency
Expressed inpicofarads (pF).
The first two digitsare significant, thethird is a multiplier.An “R” indicates a
decimal point.Examples:
1R0 = 1.0 pF
A = 50 VB = 100 V
B = ± 0.1 pF C = ± 0.25 pF D = ± 0.50 pF
F = ± 1 %G = ± 2 % J = ± 5 %
K = ± 10 %M = ± 20 %
Note: B, C, D 6.2 pF
B, C, J, K, M 6.8 pF to 9.1 pF
F, G, J, K, M 10 pF
M = Silver palladiumZ = Ni barrier with
tin/lead plate min. 4 % lead
C = Full group CL = 2000 h life test onlyM = 1000 h life test only
H = Low voltage humiditytest only
- = Group A test only
C = 7" reel/paper tapeO = 7" reel/flamed paper tape
J = 7" reel (low quantity)P = 11 1/4"/13" reel/paper tape
I = 11 1/4"/13" reel/flamed paper tapeB = Bulk
Note:“I” and “O” is used for “M”
termination code
DIMENSIONS in inches (millimeters)
PART ORDERING NUMBER
LENGTH(L)
WIDTH (W)
MAXIMUM THICKNESS (T)
TERMINATIONS PAD (P)
MINIMUM MAXIMUM
05003- 0.040 ± 0.004(1.00 ± 0.10)
0.020 ± 0.004(0.50 ± 0.10)
0.024(0.60)
0.004(0.10)
0.016(0.41)
LW
TMAX.
P
Revision: 27-Mar-13 231 Document Number: 45070For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05003www.vishay.com Vishay Vitramon
NotesRoHS-compliant except when supplied with lead (Pb)-containing termination, code “Z”
•• Paper carrier tape
SELECTION CHARTDIELECTRIC BP
STYLE 05003
TOLERANCECASE CODE 0402
VOLTAGE (VDC) 50 100
VOLTAGE CODE A B
CAP. CODE CAP.
1R0 1.0 pF •• •• B, C
1R1 1.1 pF •• •• B, C, D
1R2 1.2 pF •• •• B, C, D
1R3 1.3 pF •• •• B, C, D
1R5 1.5 pF •• •• B, C, D
1R6 1.6 pF •• •• B, C, D
1R7 1.7 pF •• •• B, C, D
1R8 1.8 pF •• •• B, C, D
2R0 2.0 pF •• •• B, C, D
2R1 2.1 pF •• •• B, C, D
2R2 2.2 pF •• •• B, C, D
2R4 2.4 pF •• •• B, C, D
2R7 2.7 pF •• •• B, C, D
3R0 3.0 pF •• •• B, C, D
3R3 3.3 pF •• •• B, C, D
3R6 3.6 pF •• •• B, C, D
3R9 3.9 pF •• •• B, C, D
4R3 4.3 pF •• •• B, C, D
4R7 4.7 pF •• •• B, C, D
5R1 5.1 pF •• •• B, C, D
5R6 5.6 pF •• •• B, C, D
6R2 6.2 pF •• •• B, C, D
6R8 6.8 pF •• •• B, C, J, K, M
7R5 7.5 pF •• •• B, C, J, K, M
8R2 8.2 pF •• •• B, C, J, K, M
9R1 9.1 pF •• •• B, C, J, K, M
100 10 pF •• •• F, G, J, K, M
110 11 pF •• •• F, G, J, K, M
120 12 pF •• •• F, G, J, K, M
130 13 pF •• •• F, G, J, K, M
150 15 pF •• •• F, G, J, K, M
180 18 pF •• •• F, G, J, K, M
200 20 pF •• F, G, J, K, M
220 22 pF •• F, G, J, K, M
240 24 pF •• F, G, J, K, M
270 27 pF •• F, G, J, K, M
Revision: 27-Mar-13 232 Document Number: 45070For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DSCC 05003www.vishay.com Vishay Vitramon
Note(1) Reference: EIA Standard RS 481 - “Taping of Surface Mount Components for Automatic Placement”
DSCC PACKAGING QUANTITIES (1)
CASECODE
TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES BULK
PACKAGING CODE“C”/”O”
PACKAGING CODE“J”
PAPER TAPE PACKAGING CODE
“P”/“I”
VIALPACKAGING CODE
“B”
0402 8 mm 4000 1000 10 000 100
STORAGE AND HANDLING CONDITIONS
(1) Store the components at 5 °C to + 40 °C ambient temperature and 70 % related humidity conditions.(2) The product is recommended to be used within a time-frame of 2 years after shipment.
Check solderability in case extended shelf life beyond the expiry date is needed.
Precautions:a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering.b. Store products on the shelf and avoid exposure to moisture or dust.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
Revision: 27-Mar-13 233 Document Number: 45070For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Contents
VJ....W1BCBasic Commodity Series ....... 235
VJ0201....W1BCUltra Small Series 0201 ......... 249
VJ06C4....W1BC Chip Array .. 254
MLCCsfor
Basic Commodity
Applications
(BME Technology)
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
Surface Mount Multilayer Ceramic Chip Capacitorsfor Commodity Applications
FEATURES• Available from 0402 to 1210 body sizes• Ultra stable C0G (NP0) dielectric• High capacitance in X5R, X7R, Y5V• For high frequency applications• Ni-barrier with 100 % tin terminations• Dry sheet technology process• Noble Metal Electrode system (NME):
for certain C0G (NP0) values• Base Metal Electrode system (BME):
for X5R, X7R, Y5V and certain C0G (NP0) values• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS• Consumer electronics• Telecommunications• Data processing• Mobile applications
ELECTRICAL SPECIFICATIONSOperating Temperature:C0G (NP0): -55 °C to +125 °CX5R: -55 °C to +85 °CX7R: -55 °C to +125 °CY5V: -25 °C to +85 °C
Capacitance Range:C0G (NP0): 0.5 pF to 39 nFX5R: 47 nF to 100 μFX7R: 100 pF to 47 μFY5V: 10 nF to 100 μF
Voltage Range:C0G (NP0): 10 VDC to 100 VDC
X5R: 6.3 VDC to 50 VDC
X7R: 10 VDC to 100 VDC
Y5V: 6.3 VDC to 100 VDC
Temperature Coefficient of Capacitance (TCC):C0G (NP0): 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °CX5R: ± 15 % from -55 °C to +85 °C without voltage appliedX7R: ± 15 % from -55 °C to +125 °C without voltage appliedY5V: + 30 % / - 80 % from -25 °C to +85 °C without voltage
applied
Insulation Resistance (IR) at UR: 10 G or R x C 500 x F whichever is less
Test Conditions for Capacitance Tolerance:preconditioning for X5R, X7R, Y5V MLCC: perform a heattreatment at +150 °C ± 10 °C for 1 h, then leave in ambientcondition for 24 h ± 2 h before measurement
Test Conditions for Capacitance and DF Measurement:measured at conditions of 30 % to 70 % related humidity.C0G (NP0): Apply 1.0 VRMS ± 0.2 VRMS, 1.0 MHz ± 10 % for
caps 1000 pF, at +25 °C ambient temperatureApply 1.0 VRMS ± 0.2 VRMS, 1.0 kHz ± 10 % forcaps > 1000 pF, at +25 °C ambient temperature
X5R / X7R: Caps 10 μF apply 1.0 VRMS ± 0.2 VRMS,1.0 kHz ± 10 %, at +25 °C ambient temperature (1)
Caps > 10 μF apply 0.5 VRMS ± 0.2 VRMS,120 Hz ± 20 %, at +25 °C ambient temperature
Y5V: Caps 10 μF apply 1.0 VRMS ± 0.2 VRMS,1.0 kHz ± 10 %, at +20 °C ambient temperatureCaps > 10 μF apply 0.5 VRMS ± 0.2 VRMS,120 Hz ± 20 %, at +20 °C ambient temperature
Note(1) Test conditions: 0.5 VRMS ± 0.2 VRMS, 1 kHz ± 10 %
Aging Rate:C0G (NP0): 0 % per decadeX5R: 6.3 VDC / 10 VDC: 3 % maximum per decade
16 VDC / 25 VDC: 2 % maximum per decadeX7R: 10 VDC: 1.5 % maximum per decade
16 VDC: 1 % maximum per decadeY5V: 6.3 VDC: 12.5 % maximum per decade
10 VDC / 16 VDC: 9 % maximum per decade 25 VDC: 7 % maximum per decade
Dielectric Strength Test:this is the maximum voltage the capacitors are tested 1 s to5 s period and the charge / discharge current does notexceed 50 mA. 100 VDC: 250 % of rated voltage
X7R: 0603: 2.2 μF / 10 V0805: 10 μF (6.3 V and 10 V)
X5R: 0402: 4.7 μF / 6.3 V and 2.2 μF / 10 V0603: 10 μF / 6.3 V
Revision: 31-Oct-14 235 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
Dissipation Factor (DF):
C0G (NP0): Cap. < 30 pF: Q 400 + 20CCap. 30 pF: Q 1000
X5R, X7R: Y5V:
Note• Detail ratings see “Selection Chart”
RATEDVOLTAGE D.F. EXCEPTION OF D.F.
50 V 2.5 %
3 % 0603 0.047 μF; 0805 0.18 μF;1206 0.47 μF
5 % 1210 4.7 μF
10 % 0603 1 μF; 0805 1 μF;1206 2.2 μF; 1210 10 μF
25 V 3.5 %
5 % 0805 1 μF; 1210 10 μF7 % 0603 0.33 μF; 1206 4.7 μF
10 %0402 0.10 μF; 0603 0.47 μF;
0805 2.2 μF; 1206 6.8 μF;1210 22 μF
16 V 3.5 %
5 %0402 0.033 μF; 0603 0.15 μF;
0805 0.68 μF; 1206 2.2 μF;1210 4.7 μF
10 %0402 0.22 μF; 0603 0.68 μF;
0805 2.2 μF; 1206 4.7 μF;1210 22 μF
10 V 5 %10 %
0402 0.33 μF; 0603 0.33 μF;0805 2.2 μF; 1206 2.2 μF;
1210 22 μF15 % 0402 1 μF
6.3 V 10 %15 %
0402 1 μF; 0603 10 μF;0805 4.7 μF; 1206 47 μF;
1210 100 μF20 % 0402 2.2 μF
RATEDVOLTAGE D.F. EXCEPTION OF D.F.
50 V 5 % 7 % 0603 0.1 μF; 0805 0.47 μF;1206 4.7 μF
35 V 7 % - -
25 V 5 %7 %
0402 0.047 μF; 0603 0.1 μF;0805 0.33 μF; 1206 1 μF;
1210 4.7 μF
9 % 0402 0.068 μF; 0603 0.47 μF;1206 4.7 μF; 1210 22 μF
16 VC < 1.0 μF 7 %
9 % 0402 0.068 μF; 0603 0.68 μF12.5 % 0402 0.22 μF
16 VC 1.0 μF 9 % 12.5 % 0603 2.2 μF; 0805 3.3 μF;
1206 10 μF; 1210 22 μF10 V 12.5 % 20 % 0402 0.47 μF6.3 V 20 % - -
QUICK REFERENCE DATA
DIELECTRIC CASEMAXIMUM VOLTAGE
(V)CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0)
0402 100 0.5 pF 1.0 nF0603 100 0.5 pF 3.3 nF0805 100 0.5 pF 12 nF1206 100 1.5 pF 39 nF
X5R
0402 25 47 nF 10 μF0603 25 220 nF 22 μF0805 25 1.5 μF 47 μF1206 25 1.5 μF 100 μF1210 16 1.5 μF 100 μF
X7R
0402 50 100 pF 220 nF0603 100 100 pF 2.2 μF0805 100 100 pF 10 μF1206 100 150 pF 22 μF1210 100 1.0 nF 47 μF
Y5V
0402 50 10 nF 1.0 μF0603 50 10 nF 4.7 μF0805 100 10 nF 10 μF1206 100 10 nF 22 μF1210 100 10 nF 100 μF
Revision: 31-Oct-14 236 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
Notes
• Detail rating see “Selection Chart”(1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance.
Consult for questions: [email protected](2) Not all values, see selection chart X7R size 0603, 0805 and 1206(3) No 5 % tolerance for X5R
ORDERING INFORMATIONVJ0402 Y 101 J X Q C W1BC
SIZECODE
DIELECTRIC CAPACITANCE TOLERANCE TERMINATION VOLTAGE (1) PACKAGING PROCESS CODEFOR BASIC
COMMODITY
04020603080512061210
A = C0G(NP0)
G = X5RY = X7RV = Y5V
Two significantdigits followedby the number
of zeros:1R0 = 1.0 pF101 = 100 pF
102 = 1000 pF152 = 1500 pF
103 = 10 000 pF104 = 100 000 pF
C0G (NP0)Cap. < 10 pF:B = ± 0.10 pFC = ± 0.25 pFD = ± 0.50 pF
Cap. 10 pF:F = ± 1 %G = ± 2 %J = ± 5 %
K = ± 10 %
X5R / X7RJ = ± 5 % (2)(3)
K = ± 10 %M = ± 20 %
Y5VM = ± 20 %Z = - 20 % /
+ 80 %
X = Ni barrier 100 % matte tin
S = 4 VY = 6.3 VQ = 10 VJ = 16 VX = 25 VZ = 35 VA = 50 V
B = 100 V
C = 7" reel /paper tape
P = 13" reel /paper tapeT = 7" reel /plastic tape
R = 13" reel /plastic tape
Revision: 31-Oct-14 237 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
Note(1) “R” = Reflow soldering process; “W” = Wave soldering process
DIMENSIONS in inches (millimeters)
SIZECODE
THICKNESSSYMBOL
SOLDERINGMETHOD (1) L W T MB
0402(1005)
N R 0.040 ± 0.002(1.00 ± 0.05)
0.020 ± 0.002(0.50 ± 0.05)
0.020 ± 0.002(0.50 ± 0.05) 0.010 + 0.002 / - 0.004
(0.25 + 0.05 / - 0.10)E R 0.040 ± 0.008
(1.00 ± 0.20)0.020 ± 0.008(0.50 ± 0.20)
0.020 ± 0.008(0.50 ± 0.20)
0603(1608)
S R / W 0.063 ± 0.004(1.60 ± 0.10)
0.030 ± 0.004(0.80 ± 0.10)
0.030 ± 0.0028(0.80 ± 0.07)
0.016 ± 0.006(0.40 ± 0.15)X R / W 0.063 + 0.006 / - 0.004
(1.60 + 0.15 / - 0.10)0.030 + 0.006 / - 0.004
(0.800.15 / - 0.10)0.030 + 0.006 / - 0.004
(0.80 + 0.15 / - 0.10)
X' R / W 0.063 ± 0.008(1.60 ± 0.20)
0.030 ± 0.008(0.80 ± 0.20)
0.030 ± 0.008(0.80 ± 0.20)
0805(2012)
A R / W
0.080 ± 0.006(2.00 ± 0.15)
0.050 ± 0.004(1.25 ± 0.10)
0.024 ± 0.004(0.60 ± 0.10)
0.020 ± 0.008(0.50 ± 0.20)
B R / W 0.030 ± 0.004(0.80 ± 0.10)
D R 0.049 ± 0.004(1.25 ± 0.10)
I R 0.080 ± 0.008(2.00 ± 0.20)
0.050 ± 0.008(1.25 ± 0.20)
0.049 ± 0.008(1.25 ± 0.20)
1206(3216)
B R / W
0.126 ± 0.006(3.20 ± 0.15) 0.063 ± 0.006
(1.60 ± 0.15)
0.030 ± 0.004(0.80 ± 0.10)
0.024 ± 0.008(0.60 ± 0.20)
C R 0.037 ± 0.004(0.95 ± 0.10)
D R 0.049 ± 0.004(1.25 ± 0.10)
J R0.126 ± 0.008(3.20 ± 0.20)
0.045 ± 0.006(1.15 ± 0.15)
G R 0.063 ± 0.008(1.60 ± 0.20)
0.063 ± 0.008(1.60 ± 0.20)
P R 0.126 + 0.012 / - 0.004(3.20 + 0.30 / - 0.10)
0.063 + 0.012 / - 0.004(1.60 + 0.30 / - 0.10)
0.063 + 0.012 / - 0.004(1.60 + 0.30 / - 0.10)
1210(3225)
C R0.126 ± 0.012(3.20 ± 0.30)
0.098 ± 0.008(2.50 ± 0.20)
0.037 ± 0.004(0.95 ± 0.10)
0.060 ± 0.010(0.75 ± 0.25)
D R 0.049 ± 0.004(1.25 ± 0.10)
G R
0.126 ± 0.016(3.20 ± 0.40)
0.098 ± 0.012(2.50 ± 0.30)
0.063 ± 0.008(1.60 ± 0.20)
K R 0.078 ± 0.008(2.00 ± 0.20)
M R 0.098 ± 0.012(2.50 ± 0.30)
T
L
MB MB
W
Revision: 31-Oct-14 238 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
SELECTION CHART DIELECTRIC C0G (NP0)
STYLE VJ0402 VJ0603 VJ0805 VJ1206
SIZE CODE 0402 0603 0805 1206
VOLTAGE (VDC) 10 16 25 50 100 10 16 25 50 100 10 16 25 50 100 10 16 25 50 100
VOLTAGE CODE Q J X A B Q J X A B Q J X A B Q J X A B
CAP. CODE CAP.
0R5 0.5 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A
1R0 1.0 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A
1R2 1.2 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A
1R5 1.5 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A B B B B B
1R8 1.8 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A B B B B B
2R2 2.2 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A B B B B B
2R7 2.7 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A B B B B B
3R3 3.3 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A B B B B B
3R9 3.9 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A B B B B B
4R7 4.7 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A B B B B B
5R6 5.6 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A B B B B B
6R8 6.8 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A B B B B B
8R2 8.2 pF N (1) N (1) N (1) N (1) N (1) S S S S S A A A A A B B B B B
100 10 pF N N N N N S S S S S A A A A A B B B B B
120 12 pF N N N N N S S S S S A A A A A B B B B B
150 15 pF N N N N N S S S S S A A A A A B B B B B
180 18 pF N N N N N S S S S S A A A A A B B B B B
220 22 pF N N N N N S S S S S A A A A A B B B B B
270 27 pF N N N N N S S S S S A A A A A B B B B B
330 33 pF N N N N N S S S S S A A A A A B B B B B
390 39 pF N N N N N S S S S S A A A A A B B B B B
470 47 pF N N N N N S S S S S A A A A A B B B B B
560 56 pF N N N N N S S S S S A A A A A B B B B B
680 68 pF N N N N N S S S S S A A A A A B B B B B
820 82 pF N N N N N S S S S S A A A A A B B B B B
101 100 pF N N N N N S S S S S A A A A A B B B B B
121 120 pF N N N N N S S S S S A A A A A B B B B B
151 150 pF N N N N N S S S S S A A A A A B B B B B
181 180 pF N N N N N S S S S S A A A A A B B B B B
221 220 pF N N N N N S S S S S A A A A A B B B B B
271 270 pF N N N N S S S S S A A A A A B B B B B
331 330 pF N N N N S S S S S A A A A A B B B B B
391 390 pF N N N N S S S S S B B B B B B B B B B
471 470 pF N N N N S S S S S B B B B B B B B B B
561 560 pF N N N N S S S S S B B B B B B B B B B
681 680 pF N N N N S S S S S B B B B B B B B B B
821 820 pF N N N N S S S S S B B B B B B B B B B
Notes• Letters indicate product thickness, see packaging quantities(1) Indicate product with Ag/Ni/Sn termination
Revision: 31-Oct-14 239 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
102 1.0 nF N N N N S S S S S B B B B B B B B B B
122 1.2 nF X X X X B B B B B B B B B B
152 1.5 nF X X X X B B B B B B B B B B
182 1.8 nF X X X X B B B B B B B B B B
222 2.2 nF X X X X B B B B B B B B B B
272 2.7 nF X X X X D D D D D B B B B B
332 3.3 nF X X X X D D D D D B B B B B
392 3.9 nF D D D D D B B B B B
472 4.7 nF D D D D D B B B B B
562 5.6 nF D D D D B B B B B
682 6.8 nF D D D D C C C C C
822 8.2 nF D D D D D D D D D
103 10 nF D D D D D D D D D
123 12 nF D (1) D (1) D (1) D (1)
153 15 nF D (1) D (1)
183 18 nF D (1) D (1)
223 22 nF D (1) D (1)
273 27 nF D (1) D (1)
333 33 nF D (1) D (1)
393 39 nF G (1) G (1)
473 47 nF
563 56 nF
683 68 nF
823 82 nF
104 100 nF
SELECTION CHART DIELECTRIC C0G (NP0)
STYLE VJ0402 VJ0603 VJ0805 VJ1206
SIZE CODE 0402 0603 0805 1206
VOLTAGE (VDC) 10 16 25 50 100 10 16 25 50 100 10 16 25 50 100 10 16 25 50 100
VOLTAGE CODE Q J X A B Q J X A B Q J X A B Q J X A B
CAP. CODE CAP.
Notes• Letters indicate product thickness, see packaging quantities(1) Indicate product with Ag/Ni/Sn termination
Revision: 31-Oct-14 240 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
Notes• Letters indicate product thickness, see packaging quantities(1) Not in 10 % (code “K”) tolerance
Notes• Letters indicate product thickness, see packaging quantities(1) Not in 10 % (code “K”) tolerance
SELECTION CHARTDIELECTRIC X5R STYLE VJ0402 VJ0603 VJ0805 SIZE CODE 0402 0603 0805 VOLTAGE (VDC) 6.3 V 10 V 16 V 25 V 50 V 6.3 V 10 V 16 V 25 V 50 V 6.3 V 10 V 16 V 25 V 50 VVOLTAGE CODE Y Q J X A Y Q J X A Y Q J X ACAP. CODE CAP.473 47 nF N563 56 nF N683 68 nF N N823 82 nF N N N104 100 nF N N N N124 120 nF154 150 nF N N184 180 nF224 220 nF N N N N X X274 270 nF X X334 330 nF N N X X X394 390 nF X X474 470 nF N N X X X564 560 nF684 680 nF N N X X X824 820 nF X X X105 1.0 μF N N N X X X X X155 1.5 μF X I I I225 2.2 μF N N X X X X I I I I335 3.3 μF I I I I475 4.7 μF E X X X I I I I106 10 μF E X' X I I I I226 22 μF X' (1) I (1) I (1)
476 47 μF I (1)
686 68 μF107 100 μF
SELECTION CHARTDIELECTRIC X5R STYLE VJ1206 VJ1210SIZE CODE 1206 1210VOLTAGE (VDC) 6.3 V 10 V 16 V 25 V 50 V 6.3 V 10 V 16 V 25 V 50 VVOLTAGE CODE Y Q J X A Y Q J X ACAP. CODE CAP.
105 1.0 μF155 1.5 μF J J K K225 2.2 μF J J P K K335 3.3 μF P P P475 4.7 μF P P P P P (1) K K K685 6.8 μF P P106 10 μF P P P P K K K M226 22 μF P P P M M M M476 47 μF P (1) P (1) M M M107 100 μF P (1) M (1) M (1)
Revision: 31-Oct-14 241 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
Notes• Letters indicate product thickness, see packaging quantities(1) Not in 5 % (code “J”) tolerance(2) Only in 10 % (code “K”) tolerance
SELECTION CHARTDIELECTRIC X7R STYLE VJ0402 VJ0603 VJ0805 SIZE CODE 0402 0603 0805 VOLTAGE (VDC) 10 V 16 V 25 V 50 V 100 V 10 V 16 V 25 V 50 V 100 V 10 V 16 V 25 V 50 V 100 VVOLTAGE CODE Q J X A B Q J X A B Q J X A BCAP. CODE CAP.101 100 pF N N N N S (1) S (1) S (1) S (1) S (1) B (1) B (1) B (1) B (1) B (1)
121 120 pF N N N N S (1) S (1) S (1) S (1) S (1) B (1) B (1) B (1) B (1) B (1)
151 150 pF N N N N S (1) S (1) S (1) S (1) S (1) B (1) B (1) B (1) B (1) B (1)
181 180 pF N N N N S (1) S (1) S (1) S (1) S (1) B (1) B (1) B (1) B (1) B (1)
221 220 pF N N N N S (1) S (1) S (1) S (1) S (1) B (1) B (1) B (1) B (1) B (1)
271 270 pF N N N N S (1) S (1) S (1) S (1) S (1) B (1) B (1) B (1) B (1) B (1)
331 330 pF N N N N S (1) S (1) S (1) S (1) S (1) B (1) B (1) B (1) B (1) B (1)
391 390 pF N N N N S (1) S (1) S (1) S (1) S (1) B (1) B (1) B (1) B (1) B (1)
471 470 pF N N N N S S S S S B B B B B561 560 pF N N N N S S S S S B B B B B681 680 pF N N N N S S S S S B B B B B821 820 pF N N N N S S S S S B B B B B102 1.0 nF N N N N S S S S S B B B B B122 1.2 nF N N N N S S S S S B B B B B152 1.5 nF N N N N S S S S S B B B B B182 1.8 nF N N N N S S S S S B B B B B222 2.2 nF N N N N S S S S S B B B B B272 2.7 nF N N N N S S S S S B B B B B332 3.3 nF N N N N S S S S S B B B B B392 3.9 nF N N N N S S S S S B B B B B472 4.7 nF N N N N S S S S S B B B B B562 5.6 nF N N N N S S S S S B B B B B682 6.8 nF N N N N S S S S S B B B B B822 8.2 nF N N N N S S S S S B B B B B103 10 nF N N N N S S S S S B B B B B123 12 nF N N N S S S S B B B B B153 15 nF N N N S S S S B B B B B183 18 nF N N N S S S S B B B B B223 22 nF N N N S S S S B B B B B273 27 nF N N N S S S S B B B B D333 33 nF N N N S S S X B B B B D393 39 nF N N N S S S X B B B B D473 47 nF N N N S S S X B B B B D563 56 nF N N S S S X B B B B D683 68 nF N N S S S X B B B B D823 82 nF N N S S S X B B B B D104 100 nF N N N S S S X B B B B / D D124 120 nF S S X B B B D154 150 nF S S X D D D D184 180 nF S S X D D D D224 220 nF N (2) N S S X D D D D274 270 nF X X X D D D334 330 nF X X X D D D I394 390 nF X X X D D D474 470 nF X X X D D D I564 560 nF X X D D D684 680 nF X X D D D824 820 nF X X D D D105 1.0 μF X X X (1) D D D I (1)
155 1.5 μF I I (1) I (1)
225 2.2 μF X (1) I I I335 3.3 μF475 4.7 μF I (1) I (1)
685 6.8 μF106 10 μF I (1)
156 15 μF226 22 μF336 33 μF476 47 μF686 68 μF
Revision: 31-Oct-14 242 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
Notes• Letters indicate product thickness, see packaging quantities(1) Not in 5 % (code “J”) tolerance(2) Only in 20 % (code “M”) tolerance
SELECTION CHARTDIELECTRIC X7RSTYLE VJ1206 VJ1210SIZE CODE 1206 1210VOLTAGE (VDC) 10 V 16 V 25 V 50 V 100 V 10 V 16 V 25 V 50 V 100 VVOLTAGE CODE Q J X A B Q J X A BCAP. CODE CAP.101 100 pF121 120 pF151 150 pF B (1) B (1) B (1) B (1) B (1)
181 180 pF B (1) B (1) B (1) B (1) B (1)
221 220 pF B (1) B (1) B (1) B (1) B (1)
271 270 pF B (1) B (1) B (1) B (1) B (1)
331 330 pF B (1) B (1) B (1) B (1) B (1)
391 390 pF B (1) B (1) B (1) B (1) B (1)
471 470 pF B B B B B561 560 pF B B B B B681 680 pF B B B B B821 820 pF B B B B B102 1.0 nF B B B B B C C C C C122 1.2 nF B B B B B C C C C C152 1.5 nF B B B B B C C C C C182 1.8 nF B B B B B C C C C C222 2.2 nF B B B B B C C C C C272 2.7 nF B B B B B C C C C C332 3.3 nF B B B B B C C C C C392 3.9 nF B B B B B C C C C C472 4.7 nF B B B B B C C C C C562 5.6 nF B B B B B C C C C C682 6.8 nF B B B B B C C C C C822 8.2 nF B B B B B C C C C C103 10 nF B B B B B C C C C C123 12 nF B B B B B C C C C C153 15 nF B B B B B C C C C C183 18 nF B B B B B C C C C C223 22 nF B B B B B C C C C C273 27 nF B B B B B C C C C C333 33 nF B B B B B C C C C C393 39 nF B B B B B C C C C C473 47 nF B B B B B C C C C C563 56 nF B B B B B C C C C C683 68 nF B B B B B C C C C C823 82 nF B B B B D C C C C C104 100 nF B B B B D C C C C C124 120 nF B B B B D C C C C C154 150 nF C C C C G C C C C D184 180 nF C C C C G C C C C D224 220 nF C C C C G C C C C D274 270 nF C C C D G C C C C G334 330 nF C C C D G C C C D G394 390 nF C C J P G C C C D M474 470 nF J J J P G C C C D M564 560 nF J J J P P D D D D M684 680 nF J J J P P D D D D K824 820 nF J J J P P D D D D K105 1.0 μF J J J P P D D D D K155 1.5 μF J J P M225 2.2 μF J J P P (1) K G M335 3.3 μF P P P G (1)
475 4.7 μF P P P P (1) K K K (1) M (1)
685 6.8 μF106 10 μF P P (1) P (1) K K K (1) M (1)
156 15 μF226 22 μF P (1) M (2) M (2)
336 33 μF476 47 μF M (1)
686 68 μF107 100 μF
Revision: 31-Oct-14 243 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
Notes• Letters indicate product thickness, please see packaging quantities(1) Not in 20 % (code “M”) tolerance
SELECTION CHART DIELECTRIC Y5V
STYLE VJ0402 VJ0603 VJ0805
SIZE CODE 0402 0603 0805
VOLTAGE (VDC) 6.3 V 10 V 16 V 25 V 50 V 100 V 10 V 16 V 25 V 50 V 100 V 10 V 16 V 25 V 50 V 100 V
VOLTAGE CODE Y Q J X A B Q J X A B Q J X A B
CAP. CODE CAP.
102 1.0 nF
122 1.2 nF
152 1.5 nF
182 1.8 nF
222 2.2 nF
272 2.7 nF
332 3.3 nF
392 3.9 nF
472 4.7 nF
562 5.6 nF
682 6.8 nF
822 8.2 nF
103 10 nF N N N N S S S S A A A A B
123 12 nF N N N N S S S S A A A A
153 15 nF N N N N S S S S A A A A B
183 18 nF N N N N S S S S A A A A
223 22 nF N N N N S S S S A A A A B
273 27 nF N N N N S S S S A A A A
333 33 nF N N N N S S S S A A A A B
393 39 nF N N N S S S S A A A A
473 47 nF N N N S S S S A A A A B
563 56 nF N N N (1) S S S S A A A A
683 68 nF N N N S S S S A A A A B
823 82 nF N N S S S S A A A A
104 100 nF N N N S S S S A A A A B
154 150 nF N S S S S A A A A
224 220 nF N N S S S S A A A A
334 330 nF N N S S S B B B B
474 470 nF N N S S X S B B B B
684 680 nF N S X B B D D
105 1.0 μF N N S X X B B D D
155 1.5 μF S D D
225 2.2 μF S X D D I
335 3.3 μF D D
475 4.7 μF X D D I
685 6.8 μF I
106 10 μF I I
226 22 μF
336 33 μF
476 47 μF
686 68 μF
107 100 μF
Revision: 31-Oct-14 244 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
Notes• Letters indicate product thickness, please see packaging quantities(1) Not in 20 % (code “M”) tolerance
SELECTION CHART DIELECTRIC Y5V
STYLE VJ1206 VJ1210
SIZE CODE 1206 1210
VOLTAGE (VDC) 10 V 16 V 25 V 35 V 50 V 100 V 6.3 V 10 V 16 V 25 V 35 V 50 V 100 V
VOLTAGE CODE Q J X Z A B Y Q J X Z A B
CAP. CODE CAP.
102 1.0 nF
122 1.2 nF
152 1.5 nF
182 1.8 nF
222 2.2 nF
272 2.7 nF
332 3.3 nF
392 3.9 nF
472 4.7 nF
562 5.6 nF
682 6.8 nF
822 8.2 nF
103 10 nF B B B B B C
123 12 nF B B B B
153 15 nF B B B B B C
183 18 nF B B B B
223 22 nF B B B B B C
273 27 nF B B B B
333 33 nF B B B B B C
393 39 nF B B B B
473 47 nF B B B B B C
563 56 nF B B B B
683 68 nF B B B B B C
823 82 nF B B B B
104 100 nF B B B B B C C C C C
154 150 nF B B B B C C C C C C
224 220 nF B B B B C C C C C C
334 330 nF B B B B C C C C C
474 470 nF B B B B C C C C
684 680 nF B B B B C C C C
105 1.0 μF C C C C C C C C
155 1.5 μF C C C C C C
225 2.2 μF C C C J (1) C C C G
335 3.3 μF J J J C C C
475 4.7 μF J J J J P C C D G
685 6.8 μF J J C C D
106 10 μF J J P D D G K
226 22 μF P K K
336 33 μF
476 47 μF K K
686 68 μF
107 100 μF M
Revision: 31-Oct-14 245 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
PACKAGING QUANTITIES
SIZE CODE(inch / mm)
MAX. THICKNESS (mm)
THICKNESSSYMBOL
PAPER TAPE PLASTIC TAPE
7" REEL (C) 13" REEL (P) 7" REEL (T) 13" REEL (R)
0402 (1002)0.55 N 10K 50K
0.70 E 10K
0603 (1608)
0.87 S 4K 15K
0.95 X 4K 15K
1.00 X' 4K 15K
0805 (2012)
0.75 A 4K 15K
0.95 B 4K 15K
1.40 D 3K 10K
1.45 I 3K 10K
1206 (3216)
0.95 B 4K 15K
1.05 C 3K 10K
1.30 J 3K 10K
1.35 D 3K 10K
1.80 G 2K
1.90 P 2K
1210 (3225)
1.05 C 3K 10K
1.35 D 3K 10K
1.80 G 2K
2.20 K 1K
2.80 M 1K
Revision: 31-Oct-14 246 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
TAPE AND REEL SPECIFICATION
Dimensions of paper tape Dimensions of plastic tape
P0 T
W
E
F
D0
B0
P1
P2A0
D1P1
P2
P0
E
F
K0
W
T
B0
D0
A0
5°
5°
DIMENSIONS PAPER TAPE in millimetersSIZE CODE 0402 0603 0805 1206
THICKNESS N E S, X, X' A B B
A0 0.62 ± 0.05 0.70 ± 0.10 1.02 ± 0.05 1.50 ± 0.10 1.50 ± 0.10 2.00 ± 0.10
B0 1.12 ± 0.05 1.20 ± 0.10 1.80 ± 0.05 2.30 ± 0.10 2.30 ± 0.10 3.50 ± 0.10
T 0.60 ± 0.05 0.70 ± 0.10 0.95 ± 0.05 0.75 ± 0.05 0.95 ± 0.05 0.95 ± 0.05
K0 - - - - - -
W 8.00 ± 0.10 8.00 ± 0.10 8.00 ± 0.10 8.00 ± 0.10 8.00 ± 0.10 8.00 ± 0.10
P0 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10
10 x P0 40.0 ± 0.10 40.0 ± 0.10 40.0 ± 0.10 40.0 ± 0.10 40.0 ± 0.10 40.0 ± 0.10
P1 2.00 ± 0.05 2.00 ± 0.05 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10
P2 2.00 ± 0.05 2.00 ± 0.05 2.00 ± 0.05 2.00 ± 0.05 2.00 ± 0.05 2.00 ± 0.05
D0 1.55 ± 0.05 1.55 ± 0.05 1.55 ± 0.05 1.55 ± 0.05 1.55 ± 0.05 1.50 ± 0.05
D1 - - - - - -
E 1.75 ± 0.05 1.75 ± 0.05 1.75 ± 0.05 1.75 ± 0.05 1.75 ± 0.05 1.75 ± 0.10
F 3.50 ± 0.05 3.50 ± 0.05 3.50 ± 0.05 3.50 ± 0.05 3.50 ± 0.05 3.50 ± 0.05
DIMENSIONS PLASTIC TAPE in millimetersSIZE CODE 0805 1206 1210
THICKNESS D, I C, J, D G, P C, D G, K M
A0 < 1.57 < 1.85 < 1.95 < 2.97 < 2.97 < 2.97
B0 < 2.40 < 3.46 < 3.67 < 3.73 < 3.73 < 3.73
T 0.23 ± 0.05 0.23 ± 0.05 0.23 ± 0.05 0.23 ± 0.05 0.23 ± 0.05 0.23 ± 0.05
K0 < 2.50 < 2.50 < 2.50 < 2.50 < 2.50 < 3.00
W 8.00 ± 0.10 8.00 ± 0.10 8.00 ± 0.10 8.00 ± 0.10 8.00 ± 0.10 8.00 ± 0.10
P0 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10
10 x P0 40.0 ± 0.10 40.0 ± 0.10 40.0 ± 0.10 40.0 ± 0.10 40.0 ± 0.10 40.0 ± 0.10
P1 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 4.00 ± 0.10
P2 2.00 ± 0.05 2.00 ± 0.05 2.00 ± 0.05 2.00 ± 0.05 2.00 ± 0.05 2.00 ± 0.05
D0 1.50 ± 0.05 1.50 ± 0.05 1.50 ± 0.05 1.50 ± 0.05 1.50 ± 0.05 1.50 ± 0.05
D1 1.00 ± 0.10 1.00 ± 0.10 1.00 ± 0.10 1.00 ± 0.10 1.00 ± 0.10 1.00 ± 0.10
E 1.75 ± 0.10 1.75 ± 0.10 1.75 ± 0.10 1.75 ± 0.10 1.75 ± 0.10 1.75 ± 0.10
F 3.50 ± 0.05 3.50 ± 0.05 3.50 ± 0.05 3.50 ± 0.05 3.50 ± 0.05 3.50 ± 0.05
Revision: 31-Oct-14 247 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Basic Commodity Serieswww.vishay.com Vishay
REEL SPECIFICATION
Note(1) C0G (NP0) items are with Ag/Ni/Sn terminations, please see selection chart
B
A D C
REEL DIMENSIONS in millimetersSYMBOL 7" REEL 13" REEL
A 13.0 ± 0.5 13.0 ± 0.5
B 9.0 ± 1.0 9.0 ± 1.0
C 178.0 ± 1.0 330.0 ± 1.0
D 60.0 ± 1.0 100.0 ± 1.0
CONSTRUCTIONNO. NAME C0G (NP0) (1) C0G (NP0) / X5R / X7R / Y5V
1 Ceramic material BaTiO3 based
2 Inner electrode AgPd alloy Ni
3
Termination
Inner layer Ag Cu
4 Middle layer Ni
5 Outer layer Sn (matt)
STORAGE AND HANDLING CONDITIONS
(1) To store products at 5 °C to 40 °C ambient temperature and 20 % to 70 % relative humidity conditions.(2) The product is recommended to be used within one year after shipment. Check solderability in case of shelf life extension is needed.
Cautions:a.Do not store products in a corrosive environment such as sulfide, chloride gas, or acid. It may cause oxidization of electrode, which
easily be resulted in poor soldering.b.To store products on the shelf and avoid exposure to moisture.c.Do not expose products to excessive shock, vibration, direct sunlight and so on.
12
3
4
5
Revision: 31-Oct-14 248 Document Number: 28548For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Ultra Small Series 0201www.vishay.com Vishay
Surface Mount Multilayer Ceramic Chip Capacitorsfor Ultra Small Commodity Applications
FEATURES• High capacitance in unit size
• High precision dimensional tolerances
• Suitably used in high-accuracy automaticmounting machine
• Dry sheet manufacturing technology
• Base Metal Electrode system (BME)
• Material categorization: for definitions ofcompliance please see www.vishay.com/doc?99912
APPLICATIONS• Miniature microwave module
• Portable equipment - mobile phone, PDA
Notes• Measured at 30 % to 70 % relative humidity• NP0: apply 1.0 VRMS ± 0.2 VRMS, 1.0 MHz ± 10 % at the condition of 25 °C ambient temperature• X7R, X5R: apply 1.0 VRMS ± 0.2 VRMS, 1.0 kHz ± 10 % (0201 / 6.3 V, cap. 224: 0.5 VRMS ± 0.2 VRMS, 1.0 kHz ± 10 %) at the condition of
25 °C ambient temperature• Preconditioning for X7R / X5R MLCC: perform a heat treatment at 150 °C ± 10 °C for 1 h, then leave in ambient condition for 24 h ± 2 h
before measurement.
Table 1
X7R / X5R:
ELECTRICAL SPECIFICATIONSSize 0201
Dielectric C0G (NP0) X7R X5R
Capacitance 0.5 pF to 120 pF 100 pF to 10 nF 100 pF to 1 μF
Capacitance Tolerance (2)
Cap. 5 pF: B (± 0.1 pF), C (± 0.25 pF)5 pF < Cap. < 10 pF: C (± 0.25 pF), D (± 0.5 pF)
Cap. 10 pF: F (± 1 %), G (2 %), J (5 %), K (± 10 %)
J (± 5 %)K (± 10 %) M (± 20 %)
J (± 5 %)K (± 10 %)M (± 20 %)
Rated Voltage (VDC) 16 V, 25 V, 50 V 10 V, 16 V, 25 V, 50 V 6.3 V, 10 V, 16 V, 25 V, 50 V
tan /Q (1) Cap. < 30 pF, Q 400 + 20 CCap. 30 pF, Q 1000
See Table 1
Insulation Resistance at UR 10 G 10 G or R x C 500 F, whichever is less
Operating Temperature -55 °C to +125 °C -55 % to +85 °C
Capacitance Change ± 30 ppm ± 15 %
Termination Ni/Sn lead (Pb)-free termination
RATED VOLTAGE D.F. EXCEPTION OF D.F.
50 V 3 % - -
25 V 3.5 % 5 % 0201 0.01 μF
16 V 3.5 % 5 % 0201 0.01 μF
10 V 5 %10 % 0201 0.012 μF
15 % 0201 0.1 μF
6.3 V 10 % 15 % 0201 0.1 μF
Revision: 09-Oct-14 249 Document Number: 28538For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Ultra Small Series 0201www.vishay.com Vishay
Note• Detail ratings see “Selection Chart” table
Note(1) Detail tolerance see under “Electrical Specifications” table
Notes(1) Reflow soldering only(2) For capacitance values 0.68 μF
QUICK REFERENCE DATA
DIELECTRIC CASE MAXIMUM VOLTAGE(V)
CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0) 0201 50 0.5 pF 120 pF
X5R 0201 50 100 pF 1 μF
X7R 0201 50 100 pF 10 nF
ORDERING INFORMATIONVJ0201 A 100 J X X C W1BC
SIZECODE
DIELECTRIC CAPACITANCE TOLERANCE (1) TERMINATION RATEDVOLTAGE
PACKAGING PROCESS CODEFOR BASIC COMMODITY
0201 A = C0G (NP0)G = X5RY = X7R
Two significantdigits followedby the number
of zeros. R is in place ofdecimal point:0R5 = 0.5 pF1R0 = 1.0 pF100 = 10 pF
B = ± 0.10 pFC = ± 0.25 pFD = ± 0.5 pF
F = ± 1 %G = ± 2 %J = ± 5 %
K = ± 10 %M = ± 20 %
X = Ni barrier 100 % matte tin
Y = 6.3 VQ = 10 VJ = 16 VX = 25 VA = 50 V
C = 7" reel /paper tape
DIMENSIONS in inches (millimeters)
SIZE CODE L W T MAX. MB
0201 (1)
(0603)
0.024 ± 0.0012(0.60 ±0.03)
0.012 ± 0.0012(0.30 ±0.03)
0.013(0.33) 0.006 ± 0.002
(0.15 ± 0.05)0.024 ± 0.002 (2)
(0.60 ±0.05)0.024 ± 0.002 (2)
(0.60 ±0.05)0.014 (2)
(0.35)
T
LMB MB
W
Revision: 09-Oct-14 250 Document Number: 28538For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Ultra Small Series 0201www.vishay.com Vishay
Notes• Letters indicate product thickness, see “Packaging quantities”(1) Only in 20 % (code “M”) tolerance(2) Not in 5 % (code “J”) tolerance
SELECTION CHARTDIELECTRIC C0G (NP0) X5R X7RSTYLE VJ0201SIZE CODE 0201VOLTAGE VDC 16 V 25 V 50 V 6.3 V 10 V 16 V 25 V 50 V 10 V 16 V 25 V 50 VVOLTAGE CODE J X A Y Q J X A Q J X ACAP. CODE CAP.
0R5 0.5 pF L L1R0 1.0 pF L L1R2 1.2 pF L L1R5 1.5 pF L L1R8 1.8 pF L L2R2 2.2 pF L L2R7 2.7 pF L L3R3 3.3 pF L L3R9 3.9 pF L L4R7 4.7 pF L L5R6 5.6 pF L L6R8 6.8 pF L L8R2 8.2 pF L L100 10 pF L L120 12 pF L L150 15 pF L L180 18 pF L L220 22 pF L L270 27 pF L L330 33 pF L L390 39 pF L L470 47 pF L L560 56 pF L L L680 68 pF L L L820 82 pF L L L101 100 pF L L L L L L L121 120 pF L L L L L L L151 150 pF L L L L181 180 pF L L L L221 220 pF L L L L271 270 pF L L L L331 330 pF L L L L391 390 pF L L L L471 470 pF L L L L561 560 pF L L L L681 680 pF L L L L821 820 pF L L L L102 1000 pF L L L L L L152 1500 pF L L L L L222 2200 pF L L L L332 3300 pF L L L L472 4700 pF L L L L682 6800 pF L L103 0.010 μF L L (2) L (2) L L153 0.015 μF L223 0.022 μF L333 0.033 μF L473 0.047 μF L683 0.068 μF L104 0.10 μF L L224 0.22 μF L (1)
474 0.47 μF L105 1.0 μF L (2)
Revision: 09-Oct-14 251 Document Number: 28538For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Ultra Small Series 0201www.vishay.com Vishay
PAPER TAPE SPECIFICATIONS
REEL SPECIFICATION
PACKAGING QUANTITIES
SIZE CODE(inch / mm)
THICKNESS (mm)
PAPER TAPE
7" REEL (C) 13" REEL (P)
0201 (0603) 0.35 15K -
FW
P0
P2D0
B0
A0P1
E
DIMENSIONS OF PAPER TAPE in millimeters
SYMBOLPRODUCT SIZE CODE
0201
A0 0.38 ± 0.05
B0 0.68 ± 0.05
W 8.00 ± 0.10
E 1.75 ± 0.05
F 3.50 ± 0.05
D0 1.55 ± 0.05
P0 4.00 ± 0.10
P1 2.00 ± 0.05
P2 2.00 ± 0.05
B
A D C
REEL DIMENSIONS AND TAPE WIDTH in millimeters
SYMBOL Ø 180 mm; 7" Ø 330 mm; 13"
A 13.0 ± 0.5 13.0 ± 0.5
B 9.0 ± 1.0 9.0 ± 1.0
C 178.0 ± 1.0 330.0 ± 1.0
D 60.0 ± 1.0 100.0 ± 1.0
Revision: 09-Oct-14 252 Document Number: 28538For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Ultra Small Series 0201www.vishay.com Vishay
CONSTRUCTION
NO. NAME C0G (NP0), X5R, X7R
1 Ceramic material BaTiO3 based
2 Inner electrode Ni
3
Termination
Inner layer Cu
4 Middle layer Ni
5 Outer layer Sn (matt)
STORAGE AND HANDLING CONDITIONS
(1) To store products at 5 °C to 40 °C ambient temperature and 20 % to 70 % relative humidity conditions.(2) The product is recommended to be used within one year after shipment. Check solderability in case of shelf life extension is needed.
Cautions:a. Do not store products in a corrosive environment such as sulfide, chloride gas, or acid. It may cause oxidization of electrode, which
easily be resulted in poor soldering.b. To store products on the shelf and avoid exposure to moisture.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
12
3
4
5
Revision: 09-Oct-14 253 Document Number: 28538For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC MLCC Chip Arraywww.vishay.com Vishay
Surface Mount Multilayer Ceramic Chip CapacitorsArray for Commodity Applications
FEATURES• High density mounting due to mounting space
saving
• Mounting cost saving
• Increased throughput
• Dry sheet manufacturing technology
• Base Metal Electrode system (BME)
• Material categorization: For definitions ofcompliance please see www.vishay.com/doc?99912
APPLICATIONS• For use as a bypass for digital and analog signal line noise
• Computer motherboards and peripherals
• The common electronic circuits
Notes(1) Measured at 30 % ~ 70 % related humidity
NP0: apply 1.0 VRMS ± 0.2 VRMS, 1.0 MHz ± 10 % at the conditions of 25 °C ambient temperatureX7R: apply 1.0 VRMS ± 0.2 VRMS, 1.0 kHz ± 10 % at the conditions of 25 °C ambient temperatureY5V: apply 1.0 VRMS ± 0.2 VRMS, 1.0 kHz ± 10 % at the conditions of 20 °C ambient temperature
(2) Preconditioning for X7R, Y5V MLCC: Perform a heat treatment at 150 °C ± 10 °C for 1 h, then leave in ambient condition for 24 h ± 2 hbefore measurement.
ELECTRICAL SPECIFICATION
Size 4 x 0603
Dielectric C0G (NP0) X7R Y5V
Capacitance (1) 10 pF to 470 pF 180 pF to 100 nF 10 nF to 100 nF
Capacitance Tolerance (2) J (± 5 %), K (± 10 %) K (± 10 %), M (± 20 %) M (± 20 %)Z (-20 %/+80 %)
Rated Voltage (VDC) 50 V 16 V, 50 V 50 V
tan /Q (1) Cap. < 30 pF: Q 400 + 20 CCap. 30 pF: Q 1000
UR = 50 V: 2.5 %UR = 16 V: 3.5 %
5 %
Insulation Resistance at UR 10 G 10 G or R x C 500 x F, whichever is less
Operating Temperature -55 °C to +125 °C -25 °C to +85 °C
Capacitance Change ± 30 ppm ± 15 % +30 %/-80 %
Termination Ni/Sn lead (Pb)-free termination
Revision: 07-Nov-13 254 Document Number: 28539For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC MLCC Chip Arraywww.vishay.com Vishay
Note• Detail ratings see “Selection Chart”
QUICK REFERENCE DATA
DIELECTRIC CASEMAXIMUM VOLTAGE
(V)
CAPACITANCE
MINIMUM MAXIMUM
C0G (NP0) 0612 50 10 pF 470 pF
X7R 0612 50 180 pF 100 nF
Y5V 0612 50 10 nF 100 nF
ORDERING INFORMATIONVJ06C4 A 100 J X A C W1BC
SIZECODE
DIELECTRIC CAPACITANCE TOLERANCE TERMINATION RATEDVOLTAGE
PACKAGING PROCESS CODE FORBASIC COMMODITY
06C4 A = C0G (NP0)Y = X7RV = Y5V
Two significantdigits followedby the number
of zeros. R is in place ofdecimal point:100 = 10 pF
101 = 100 pF
J = ± 5 %K = ± 10 %M = ± 20 %Z = -20 %/
+80 %
X = Ni Barrier J = 16 VA = 50 V
C = 7" reel/paper tape
DIMENSIONS in inches (millimeters)
SIZE CODE L WT
MAX.S BW P
0612(1632)
0.125 0.006(3.20 ± 0.15)
0.063 0.006(1.60 ± 0.15)
0.036(0.90)
0.012 ± 0.008(0.30 ± 0.20)
0.016 ± 0.006(0.40 ± 0.15)
0.031 ± 0.006(0.80 ± 0.15)
L
S
PBW
W
T
Revision: 07-Nov-13 255 Document Number: 28539For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC MLCC Chip Arraywww.vishay.com Vishay
Note• Letters indicate product thickness, see “Packaging Quantities”
SELECTION CHARTDIELECTRIC C0G (NP0) X7R Y5V
STYLE VJ06C4
SIZE CODE 0612 (4 x 0603)
VOLTAGE VDC 50 V 16 V 50 V 50 V
VOLTAGE CODE A J A A
CAP. CODE CAP.
100 10 pF B
150 15 pF B
220 22 pF B
330 33 pF B
470 47 pF B
680 68 pF B
101 100 pF B
151 150 pF B
181 180 pF B B
221 220 pF B B
271 270 pF B B
331 330 pF B B
391 390 pF B
471 470 pF B B
102 1.0 nF B
152 1.5 nF B
222 2.2 nF B
332 3.3 nF B
472 4.7 nF B
682 6.8 nF B
103 10 nF B B
153 15 nF B B B
223 22 nF B B B
333 33 nF B B
473 47 nF B B
683 68 nF B
104 100 nF B B
Revision: 07-Nov-13 256 Document Number: 28539For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC MLCC Chip Arraywww.vishay.com Vishay
PAPER TAPE SPECIFICATIONS
REEL SPECIFICATION
PACKAGING QUANTITIES
SIZE CODE THICKNESS (mm)
PAPER TAPE
7" REEL (C) 13" REEL (P)
06C4 (4 x 0603) 0.80 ± 0.10 4K -
FW
P0
P2D0
B0
A0P1
E
DIMENSIONS OF PAPER TAPE in millimeters
SYMBOLPRODUCT SIZE CODE
06C4 (4 x 0603)
A0 2.00 ± 0.10
B0 3.50 ± 0.10
W 8.00 ± 0.10
E 1.75 ± 0.05
F 3.50 ± 0.05
D0 1.50 ± 0.05
P0 4.00 ± 0.10
P1 4.00 ± 0.10
P2 2.00 ± 0.05
B
A D C
REEL DIMENSIONS AND TAPE WIDTH in millimeters
SYMBOL Ø 180 mm; 7" Ø 330 mm; 13"
A 13.0 ± 0.5 13.0 ± 0.5
B 9.0 ± 1.0 9.0 ± 1.0
C 178.0 ± 1.0 330.0 ± 1.0
D 60.0 ± 1.0 100.0 ± 1.0
Revision: 07-Nov-13 257 Document Number: 28539For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC MLCC Chip Arraywww.vishay.com Vishay
CONSTRUCTIONNO. NAME C0G (NP0), X7R, Y5V
1 Ceramic material BaTiO3 based
2 Inner electrode Ni
3
Termination
Inner layer Cu
4 Middle layer Ni
5 Outer layer Sn (matt)
STORAGE AND HANDLING CONDITIONS
(1) To store products at 5 °C to 40 °C ambient temperature and 20 % to 70 % relative humidity conditions.(2) The product is recommended to be used within one year after shipment. Check solderability in case of shelf life extension is needed.
Cautions:a. Do not store products in a corrosive environment such as sulfide, chloride gas, or acid. It may cause oxidization of electrode, which
easily be resulted in poor soldering.b. To store products on the shelf and avoid exposure to moisture.c. Do not expose products to excessive shock, vibration, direct sunlight and so on.
12
3
4
5
Revision: 07-Nov-13 258 Document Number: 28539For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Contents
VJ Vitramon Packaging.......... 260
VJ SolderingRecommendations................. 265
VJ Marking Options ............... 268
Vishay Vitramon MLCCEnd Termination..................... 270
VJ....W1BC Test Procedureand Requirements.................. 272
VJ....W1BC Soldering andFootprint Design .................... 278
Related Documents
and Requirements
VJ Vitramon Packagingwww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitors
Note(1) Drive spokes optional, if used, asterisked dimensions B and D apply.
Notes(1) For reels less than 360 mm diameter (A), the most widely used reel diameters are 178 mm ± 2 mm and 330 mm ± 2 mm. Reel diameters
ranging from 254 mm to 292 mm also exist. Commonly used hub diameters are 80 mm, 100 mm, 150 mm and 178 mm.(2) Tape with components must wrap around hub without damage.
REEL DIMENSIONS in inches (millimeters)
TAPESIZE A MAX. B MIN. C D MIN. N MIN. W1 W2 MAX. W3
8 mm
12.992(330) 0.059
(1.5) 0.512 + 0.020/- 0.008
(13.0 + 0.50/- 0.20) 0.795(20.2)
1.969(50.0)
0.331 + 0.059/- 0.0(8.4 + 1.5/- 0.0)
0.567(14.4) Shall
accommodate tape width
without interference
12 mm0.488 + 0.079/- 0.0
(12.4 + 2.0/- 0.0) 0.724(18.4)
16 mm2.401(61.0)
0.646 + 0.079/- 0.0(16.4 + 2.0/- 0.0)
0.882(22.4)
24 mm23.976(609)
2.362(60.0)
0.960 + 0.079/- 0.0(24.4 + 2.0/- 0.0)
1.197(30.4)
1.457(37.0)
CArbor hole
diameter
W1 (measured at hub)
W2 (measured at hub)
W3 Includes flange distortion at outer edge
N (hub diameter)
D
A
Full radius
B (1)
If present, tape slot in core for tape start: 2.5 mm min. width x 10.0 min. depth.
Access hole at slotlocation (Ø 40 mm min.)
Revision: 19-Aug-14 260 Document Number: 45051For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Vitramon Packagingwww.vishay.com Vishay Vitramon
Notes(1) For details see individual datasheet.(2) Reference: EIA standard 481 - “Taping of Surface Mount Components for Automatic Handling” packaging quantities used unless specified
in single datasheets.(3) n/a = not available, not supported anymore.(4) Quantity can vary with customer request.(5) Flamed paper tape code “O” (7" reel) and “I” (11 1/4" / 13" reel) for AgPd terminated parts (termination code ”F”, “E” and size 0402 /
0603 / 0805).(6) Packaging code “C/P” or “T/R” and lower quantities can depend from product thickness.(7) Packaging code “E” and “M” used in automotive series (VJ..31 / VJ..34) for size 0603 / 0805 / 1206 / 1210 where applicable.
PLASTIC BLACK CONDUCTIVE POLYCARBONATE CARRIER TAPE
Notes(1) Contact [email protected] for available series.(2) Reference: EIA standard 481 - “Taping of Surface Mount Components for Automatic Handling” packaging quantities used unless specified
in single datasheets.(3) n/a = not available, not supported anymore.(4) Quantity can vary with customer request.
STANDARD PACKAGING QUANTITIES (1)(2)(3)(7)
BODY SIZE TAPE SIZE
7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES
PAPER TAPEPACKAGING CODE
“C” / “O” (5)
PLASTIC TAPE PACKAGING CODE
“T” / “E” (7)
LOW QUANTITY
“J”
PAPER TAPE PACKAGING CODE
“P” / “I” (5)
PLASTIC TAPE PACKAGING CODE
“R” / “M” (7)
0402 (4) 8 mm 5000 / 10 000 n/a 1000 10 000 / 30 000 n/a0505 8 mm n/a 3000 1000 n/a 10 0000603 8 mm 4000 4000 1000 10 000 10 000
0805 (6) 8 mm 3000 3000 1000 10 000 10 0001111 8 mm n/a 2500 1000 n/a 10 000
1206 (6) 8 mm 3000 2500 / 3000 1000 10 000 9000 / 10 0001210 (6) 8 mm n/a 2000 / 2500 / 3000 1000 n/a 9000 / 10 0001808 12 mm n/a 2000 500 n/a 10 0001812 12 mm n/a 1000 500 n/a 40001825 12 mm n/a 1000 500 n/a 40002008 12 mm n/a 2000 n/a n/a 10 0002012 12 mm n/a 1000 n/a n/a 40002220 12 mm n/a 1000 500 n/a 40002225 12 mm n/a 1000 500 n/a 40002525 12 mm n/a 1000 500 n/a n/a3040 16 mm n/a 500 n/a n/a n/a3640 16 mm n/a 500 n/a n/a n/a3838 16 mm n/a 400 n/a n/a n/a4044 24 mm n/a 300 n/a n/a n/a
STANDARD PACKAGING QUANTITIES (1)(2)
BODYSIZE
TAPESIZE
7" REEL QUANTITIESPACKAGING CODE MUST INCL. PROCESS CODE
“TA3”
11 1/4" AND 13" REEL QUANTITIESPACKAGING CODE MUST INCL. PROCESS CODE
“RA3”
0603 8 mm 4000 10 0000805 8 mm 3000 10 000
1206 (4) 8 mm 2500 / 3000 9000 / 10 0001210 (4) 8 mm 2000 / 2500 / 3000 9000 / 10 0001808 12 mm 2000 10 0001812 12 mm 1000 40001825 12 mm 1000 40002220 12 mm 1000 40002225 12 mm 1000 40003040 16 mm 500 n/a3640 16 mm 500 n/a4044 24 mm 300 n/a
Revision: 19-Aug-14 261 Document Number: 45051For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Vitramon Packagingwww.vishay.com Vishay Vitramon
EMBOSSED 8 mm, 12 mm, 16 mm AND 24 mm CARRIER TAPE
Figure 1
Note(1) The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that:
a) The component does not protrude above the top surface of the carrier tape.b) The component can be removed from the cavity in a vertical direction without mechanical restriction, after the cover tape has been
removed.c) Rotation of the component is limited to 20° maximum for 8 mm/12 mm tapes and 10° maximum for 16 mm/24 mm figure 4 and 5.d) Lateral movement of the component is restricted to 0.5 mm maximum for 8 mm, 12 mm wide tape and to 1.0 mm maximum for 16 mm /
24 mm wide tape figure 3.
CONSTANT CARRIER TAPE METRIC DIMENSIONS in inches (millimeters)TAPE SIZE D0 E1 P0 P2 S1 MIN. T MAX. T1 MAX.
8 mm and 12 mm 0.059 + 0.004/- 0.0(1.50 + 0.10/- 0.0)
0.069 ± 0.004(1.75 ± 0.10)
0.175 ± 0.004(4.0 ± 0.10)
0.079 ± 0.002(2.0 ± 0.05)
0.024(0.60)
0.024)(0.60)
0.004(0.10)
VARIABLE CARRIER TAPE METRIC DIMENSIONS in inches (millimeters)TAPE SIZE B1 MAX. D1 MIN. E2 MIN. F P1 R MIN. T2 MAX. W MAX. A0, B0 AND K0
8 mm2 mmPitch
0.171(4.35)
0.0177(0.450)
0.246(6.25)
0.138 ± 0.002(3.50 ± 0.05)
0.79 ± 0.004(2.00 ± 0.10)
0.984(25.0)
0.098(2.50)
0.327(8.30) See note (1)
8 mm4 mmPitch
0.171(4.35)
0.0177(0.450)
0.246(6.25)
0.138 ± 0.002(3.50 ± 0.05)
0.157 ± 0.004(4.00 ± 0.10)
0.984(25.0)
0.098(2.50)
0.327(8.30) See note (1)
12 mm2 mmPitch
0.323(8.20)
0.059(1.50)
0.404(10.25)
0.217 ± 0.002(5.50 ± 0.05)
0.157 ± 0.004(4.00 ± 0.10)
1.181(30.0)
0.256(6.50)
0.484(12.30) See note (1)
16 mm4 mmPitch
0.476(12.1)
0.059(1.50)
0.561(14.25)
0.295 ± 0.004(7.50 ± 0.10)
0.157 ± 0.004(4.00 ± 0.10)
1.181(30.0)
0.341(8.0)
0.641(16.3) See note (1)
24 mmPitch
0.791(20.1)
0.059(1.50)
0.876(22.25)
0.453 ± 0.004(11.5 ± 0.10)
0.157 ± 0.004(4.00 ± 0.10)
to0.787 ± 0.004(20.00 ± 0.10)in 0.157 (4.00)
increments
1.181(30.0)
0.472(12.0)
0.956(24.3) See note (1)
T T2
K0
S1
T1
B1
F
P1
A0
B0 E2
W
P0 E1
Ø D1
Embossment for cavity size see variable dimension table.
Cavity center lines
Cover tape
B1 is for tape feeder reference only, including draft concentric about B0.
[10 pitches cumulative tolerance on tape ± 0.2 mm]
User feed direction
D0ØP2
Revision: 19-Aug-14 262 Document Number: 45051For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Vitramon Packagingwww.vishay.com Vishay Vitramon
PAPER 8 mm CARRIER TAPE
Figure 2
Note(1) The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that:
a) The component does not protrude above the top surface of the carrier tape.b) The component can be removed from the cavity in a vertical direction without mechanical restriction, after the cover tape has been
removed.c) Rotation of the component is limited to 20° maximum for 8 mm and 12 mm tapes and 10° maximum for 16 mm figure 3 and 4.d) Lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for
16 mm wide tape figure 5.
CONSTANT CARRIER TAPE METRIC DIMENSIONS in inches (millimeters)
TAPE SIZE D0 E1 P0 P2 T1 MAX. G MIN. R REF.
8 mm0.059 + 0.004/- 0.0(1.50 + 0.10/- 0.0)
0.069 + 0.004(1.75 ± 0.10)
0.175 + 0.004(4.0 ± 0.10)
0.079 + 0.002(2.0 ± 0.05)
0.024(0.60)
0.029(0.75)
0.010(0.25)
VARIABLE CARRIER TAPE METRIC DIMENSIONS in inches (millimeters)
TAPE SIZE E2 MIN. F P1 W MAX. A0, B0 AND K0 T
8 mm2 mmPitch
0.246(6.25)
0.138 ± 0.002(3.50 ± 0.05)
0.79 ± 0.004(2.00 ± 0.10)
0.327(8.30)
See note 11.1 mm maximum for
paper base tape
8 mm4 mmPitch
0.246(6.25)
0.138 ± 0.002(3.50 ± 0.05)
0.157 ± 0.004(4.00 ± 0.10)
0.327(8.30)
See note 11.1 mm maximum for
paper base tape
Ø D0
T
T1
Bottom cover tape
T1
F
P1
0
B0 E2
P2
W
P0 E1
Cavity size (1)
Bottom cover tape
User feed direction
Cavity center lines
Cover tape
[10 pitches cumulative tolerance on tape ± 0.2 mm]
G
A
Revision: 19-Aug-14 263 Document Number: 45051For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Vitramon Packagingwww.vishay.com Vishay Vitramon
MAXIMUM COMPONENT ROTATION FOR PUNCHED AND EMBOSSED CARRIER
Figure 3
Figure 4
MAXIMUM LATERAL MOVEMENT FOR PUNCHED AND EMBOSSED CARRIER
Figure 5
BENDING RADIUS FOR PUNCHED EMBOSSED CARRIER
Figure 6
Note(1) The tape with or without components shall pass without damage round “R”, see dimensions table
8 mm and 12 mm carrier: 0.020" (0.50 mm) maximum16 mm and 24 mm carrier: 0.039" (1.0 mm) maximum
8 mm and 12 mm carrier: 0.020" (0.50 mm) maximum 16 mm and 24 mm carrier: 0.039" (1.0 mm) maximum
Maximum Lateral Movement Carrier Top View
Maximum Component Rotation Embossed Carrier Side View Maximum Component Rotation Paper Carrier Side View
8 mm carrier: 20°8 mm and 12 mm carrier: 20°
16 mm and 24 mm carrier: 10°
Typical pocket centerline
Maximum Component Rotation Top View
8 mm and 12 mm carrier: 20°16 mm and 24 mm carrier: 10°
Typical pocket centerline
R
Punched carrier bending radius (1)
R
Embossed carrier bending radius (1)
Revision: 19-Aug-14 264 Document Number: 45051For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Soldering Recommendationswww.vishay.com Vishay
Surface Mount Multilayer Ceramic Chip Capacitors
SOLDERING RECOMMENDATIONS
1. Termination Selection (1)
• The termination selected depends on the assemblymethod to be used and the requirements of theapplication.
• Reflow solder assembly: select termination code “X”.For CDR-MIL-PRF 55681 product, select terminationcode “W” or “Y”.
• Wave solder assembly: select termination code “X”.For CDR-MIL-PRF 55681 product, select terminationcode “W” or “Y”.
• Additional board flex protection: select the polymertermination code “B”.
• Conductive epoxy assembly: select termination code“F” and “E” (2)
For CDR-MIL-PRF 55681 and DSCC product, selecttermination code “M”.
• Non-magnetic requirements: select termination code“C” for solder assembly, or “N” for conductive epoxyassembly.
• Lead-bearing requirements: select termination code ”L”For CDR-MIL-PRF 55681 and DSCC product, selecttermination code “Z” or “U”.
Notes(1) Where applicable, see datasheets(2) Termination code “E” is for conductive epoxy assembly, contact
[email protected] for availability.
2. Chip Size vs. Solder ProfileA. 0402, 0505, 0603, 0805, 1111, 1206, and 1210
(thickness 0.049", 1.24 mm) can be used in all threesolder systems shown on the following page.1111, 1210 to 1812 with a thickness > 0.049" (1.24 mm)and case size 1825 and larger should not be wavesoldered.
B. Solder profiles should be properly controlled to minimizeany thermal shock to the capacitor(s).
(See recommended solder profiles on the following page.)
3. Soldering Flux
Use mildly activated rosin flux RMA or RA types or lowresidue liquid fluxes (no-clean flux). Flux residues fromno-clean flux can be removed with aqueous cleaners.During wave soldering ensure that the majority of solventsare removed at preheat.
4. Solder Type
Both, lead containing solders, such as Sn60, Sn62 or Sn63and lead free solders, such as SnAgCu, can be used withour MLCCs.
In case of termination code “C”, use lead containing orlead (Pb)-free SAC405 solder.
5. Soldering Techniques
Generalized soldering curves shown on next page.
6. Soldering with a Solder Iron
Attachment by soldering iron is not recommended. A heatshock may cause a crack in the MLCC chip capacitors,however, if solder iron is used, the following precautionsshould be taken:
A. Preheat the chip capacitor to +150 °C minimum. Use hotplate or hot air flow for preheat.
B. Use a low wattage, temperature controlled iron.
C. Tip temperature setting 280 °C and a maximumsoldering time of 5 s.
D. Use a soldering tip no greater than 0.120" (3.0 mm) indiameter. Apply the transmission of heat through thesoldering material.
E. When removal of chip capacitor is necessary, a hot airpencil is the preferred tool.
7. Cool Down
After soldering, allow the chip to cool at room ambientconditions. Using forced cool air or refrigerated air forexpediting the cooling process is not recommended andcan create thermal shock cracks and may facilitate boardbend stresses.
8. Cleaning
Selection of an appropriate cleaning solvent is dependentupon the type of flux used. Cleaning in alcohol, water,hydrocarbons or any of the common, halogenateddegreaser solvents is not detrimental to Vishay chipcapacitors.
Revision: 26-Jan-15 265 Document Number: 45034For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Soldering Recommendationswww.vishay.com Vishay
WAVE AND REFLOW SOLDERING GRAPHS
300
250
200
150
100
50
0
SECOND WAVE
FIRST WAVE
WAVE SOLDERING
235 °C to 260 °C
200 K/s
~~
~~~~ 2 K/s
~~ 2 K/s
5 K/s
100 °C to 130 °CFORCEDCOOLING
T(°C)
10 s
0 50 100 150 200 250t (s)
300
250
200
150
100
50
0
Sn-Pb EUTECTIC SOLDER PASTE
MAX. TEMPERATURE
30 ~ 60 s 30 ~ 60 s 30 ~ 60 s
MIN. TEMPERATURE
> 215 °C 20 ~ 40 s
IR REFLOW WITH SnPb SOLDER
T(°C)
TIME
TE
MP
ER
AT
UR
E (°
C)
300
250
200
150
100
0 50 100 150 200 250 300 350 400TIME (s)
LEAD (Pb)-FREE SOLDERING PROFILE
MIN. 300 s MAX. 260 °C MIN. 255 °C
T (SOLID) MIN. 217 °C
MIN. 190 °CMIN. 40 sMIN. 90 s
RAMP UP TO 150 °CMAX. 3 K/s
RAMP DOWN FROM T (SOLID)
MAX. 6 K/sMIN. 110 s50
0
Revision: 26-Jan-15 266 Document Number: 45034For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Soldering Recommendationswww.vishay.com Vishay
WAVE AND REFLOW SOLDERING
WAVE SOLDERINGVishay offers the following recommendations:
1. Set dwell time in the solder wave 2 s to 3 s. Solder potset at +240 °C to +260 °C. Belt speed at 3 feet/min to 5feet/min.
2. Adjust flux station (foam, spray or wave) topside preheatat +80 °C to +105 °C.
3. Set preheat +160 °C below the solder wavetemperature. Usually maximum underside PC boardtemperature at last preheat zone is +150 °C. Preheatrate should be 1.5 °C/s to 2.5 °C/s.
4. Do not force cool the PC board. Maintain a uniformprofile.
5. Finally check that the delta difference between thesolder temperature and the temperature as the PCboard leaves the last preheat zone is +160 °C or less.Chip size and mass make some types more prone tothermal shocking during the soldering operation,leading to insulation resistance (IR) failures in use.
Vishay does not recommend wave soldering for chip size1111, 1210 to 1812 with a thickness > 0.049" (1.24 mm) andcase size 1825 and larger should not be wave soldered.
REFLOW SOLDERING (SnPb - Solder)The reflow soldering process using no-clean solder pastefor mounting ceramic chip capacitors has wide acceptance.Chip capacitors may develop thermally induced cracks if thetemperature changes in reflow process are not controlled.Vishay offers the following recommendations:
1. Set peak reflow temperature at +215 °C to +260 °Cbased on paste melting point.
2. First preheat zone temperature elevation at +150 °C± 10 °C, ramp rate 3 °C/s.
3. Second preheat zone temperature +150 °C ± 10 °C,ramp rate of 0.1 °C/s. Set preheat for 60 s. Longpreheat times could cause solder balls near thecapacitor/other components.
4. Adjust reflow zone temperatures to +150 °C ± 10 °C to+225 °C ± 5 °C at ramp of 4 °C/s to 5 °C/s. Total time atreflow over +200 °C should not exceed 15 s to 20 s.
5. Use natural cooling at the final cooling zone. Maintain auniform profile no more than -3 °C/s.
VAPOR PHASE REFLOW
With vapor phase reflow, heat reaches the product uniformlyand quickly because of vapor condensation heating. Duringcondensation heating a dense vapor condenses on allexposed surfaces. Due to the inherent low boiling point(+215 °C) for liquids used in vapor phase, ceramic chips canbe reflowed without thermal shock damage. Vishay offersthe following recommendations:
1. Preheat or pre-bake zone duration should be about1.5 min to 2 min. Infrared heating can be used for preheatsections.
2. Vapor phase zone maximum temperature is +215 °Cwith typical settings at +210 °C.
3. Total duration is typically 4 min to 5 min, use naturalcooling at the final cooling zone.
200215
150
100
50
0 1 2 3 4
TIME (min)
SOLDERING ZONE RANGE RECOMMENDED AREA
ENTRANCE-PREHEAT
REFLOWZONE
COOL DOWNZONE
TE
MP
ER
AT
UR
E (
°C)
Revision: 26-Jan-15 267 Document Number: 45034For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Marking Optionswww.vishay.com Vishay Vitramon
Surface Mount Multilayer Ceramic Chip CapacitorsVishay Vitramon Marking Option
Vishay Vitramon can provide on selected MLCC capacitors a laser marking.
E. I. A. MARKING CODESLETTER 0 1 2 3 4 5 6 7
A 1 10 100 1000 10 000 100 000 1 000 000 10 000 000
B 1.1 11 110 1100 11 000 110 000 1 100 000 11 000 000
C 1.2 12 120 1200 12 000 120 000 1 200 000 12 000 000
D 1.3 13 130 1300 13 000 130 000 1 300 000 13 000 000
E 1.5 15 150 1500 15 000 150 000 1 500 000 15 000 000
F 1.6 16 160 1600 16 000 160 000 1 600 000 -
G 1.8 18 180 1800 18 000 180 000 1 800 000 -
H 2 20 200 2000 20 000 200 000 2 000 000 -
J 2.2 22 220 2200 22 000 220 000 2 200 000 -
K 2.4 24 240 2400 24 000 240 000 2 400 000 -
L 2.7 27 270 2700 27 000 270 000 2 700 000 -
M 3 30 300 3000 30 000 300 000 3 000 000 -
N 3.3 33 330 3300 33 000 330 000 3 300 000 -
P 3.6 36 360 3600 36 000 360 000 3 600 000 -
Q 3.9 39 390 3900 39 000 390 000 3 900 000 -
R 4.3 43 430 4300 43 000 430 000 4 300 000 -
S 4.7 47 470 4700 47 000 470 000 4 700 000 -
T 5.1 51 510 5100 51 000 510 000 5 100 000 -
U 5.6 56 560 5600 56 000 560 000 5 600 000 -
V 6.2 62 620 6200 62 000 620 000 6 200 000 -
W 6.8 68 680 6800 68 000 680 000 6 800 000 -
X 7.5 75 750 7500 75 000 750 000 7 500 000 -
Y 8.2 82 820 8200 82 000 820 000 8 200 000 -
Z 9.1 91 910 9100 91 000 910 000 9 100 000 -
a 2.5 25 250 2500 25 000 250 000 2 500 000 -
b 3.5 35 350 3500 35 000 350 000 3 500 000 -
d 4 40 400 4000 40 000 400 000 4 000 000 -
e 4.5 45 450 4500 45 000 450 000 4 500 000 -
f 5 50 500 5000 50 000 500 000 5 000 000 -
m 6 60 600 6000 60 000 600 000 6 000 000 -
n 7 70 700 7000 70 000 700 000 7 000 000 -
t 8 80 800 8000 80 000 800 000 8 000 000 -
y 9 90 900 9000 90 000 900 000 9 000 000 -
Revision: 16-Jul-14 268 Document Number: 45028For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ Marking Optionswww.vishay.com Vishay Vitramon
Notes• Values less than 1.0 pF use 2nd character “9” (= divided by 10).• Marking appears in laser-marked legible contrast.• Orientation of marking is vendor optional. Reference EIA 198.• For details see individual datasheets.
Notes• Marking only on size 0805 and 1206.• No marking for AgPd terminated parts, termination code “F” and “E”.• Marking appears in laser-marked legible contrast.
Note• Marking appears in laser-marked legible contrast.
E. I. A. MARKING CODES - MARKING OPTION “M”
AUTOMOTIVE SERIES MARKING - MARKING OPTION “B”
SAFETY CAP SERIES MARKING - MARKING OPTION “S”
3rd digit: multiplier
Examples:
VA9 = 0.1 pFVd9 = 0.4 pFVA3 = 1000 pFVS4 = 47 000 pF2nd digit: capacitance code
1st digit: Vishay Vitramon company logo
VA1
Example:
V4a = year 2014, week 1
3rd digit “a to z” = week 1 to 26 “A to Z” = week 27 to 522nd digit = year1st digit = Vishay Vitramon company logo
V4a
Examples:
VC = C0G (NP0), X1/Y2VT = C0G (NP0), X2VA = X7R, X1/Y2VM = X7R, X2
2nd digit = dielectric and classification1st digit = Vishay Vitramon company logo
VC
Revision: 16-Jul-14 269 Document Number: 45028For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
V I S H A Y V I T R A M O N
Ceramic Capacitors Tech Note TN-0029
Vishay Vitramon MLCC End Termination
www.vishay.com
TE
CH
NIC
AL
NO
TE
By Eli Bershadsky and Dmitry Kan
Notes(1) Case sizes 1111, 1210 to 1812 with a thickness > 0.049" (1.24 mm) and case sizes 1825 and larger should NOT be wave soldered.(2) Termination code “E” is for conductive epoxy assembly, contact [email protected] for availability.(3) CDR and DSCC part numbers only.(4) CDR “U” termination code: Base metallization-barrier metal-solder coated (tin/lead alloy, with a minimum of 4 % lead).
Solder has a melting point of + 200 °C or less. Solder coat thickness is a minimum of 60 microinches.• Solder iron techniques are not recommended. For more information on soldering visit www.vishay.com/doc?45034.• Contact [email protected] with respect to specific part number requirements.
(5) Terminations code “F” and “M” may exhibit high wetting angles and lower fillet heights as compared to barrier plate terminations such asX-term. Contact [email protected] with respect to specific requirements.
(6) For “C” termination solder coverage should be at least 90 % of the terminal critical areas in soldering.
TERMINATION CODEFROM PART NUMBERING
TERMINATION DEFINITION
ACCEPTED ASSEMBLY METHODS
F, M (3) Fired, thick film, silver / palladium Conductive epoxy / reflow solder (5)
E (2) Fired, thick film, silver / palladium Conductive epoxy
N Fired, thick film, non magnetic material Conductive epoxy
C (6) Copper with an outer layer of 100 % tin plate matte finishfor multi-solder mounting
Wave solder (1) / reflow solder /vapor phase reflow
W (3), X, Y (3) Fired, thick film silver, covered by 100 % nickel barrier plate with an outer layer of 100 % tin plate matte finish for multi-solder mounting
Wave solder (1) / reflow solder /vapor phase reflow
L, Z (3) Fired, thick film silver, cover by 100 % nickel barrier plate with an
outer layer of tin / lead plate matte finish with a minimum of 4 % leadfor multi-solder mounting
Wave solder (1) / reflow solder /vapor phase reflow
U (4)Fired, thick film silver, cover by 100 % nickel barrier plate with an outer
layer of tin / lead plate finish matte with a minimum of 4 % lead forSn60 / Pb40 solder coat
Wave solder (1) / reflow solder /vapor phase reflow
BFired, thick film silver, cured thick film polymer silver, covered by100 % nickel barrier plate with an outer layer of 100 % tin plate
matte finish for multi-solder mounting
Wave solder (1) / reflow solder /vapor phase reflow
Ag:silver
Sn: 100 % tinplate matte finish(W, X, Y) or Sn / Pbtin / lead platematte finish witha minimum of4 % lead (L, Z)
Ni:nickelplatebarrier
Figure 2 Termination codes:L, W, X, Y, Z
Sn60 / Pb40solder coat finishwith minimumof 4 % lead
Figure 3CDR terminationcode: U
Ni:nickelplatebarrier
Ag:silver
AgPd:silver-palladium
Figure 1 Terminationcodes: F, M, E
Sn: 100 %tin platematte finish
Figure 6Termination code: C
Cu:copperbarrier
Ag:silver
Figure 4Termination code: B
Ni:nickelplatebarrier
Polymer
Sn: 100 %tin platematte finish
Ag:silver
Non-magnetic
Figure 5Terminationcode: N
Revision: 27-Jan-15 270 Document Number: 45063For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Vishay Vitramon MLCC End Termination
Tech Note TN-0029www.vishay.com Vishay Vitramon
TE
CH
NIC
AL
NO
TE
Notes• Element definition: Ag = silver, Pd = palladium, Ni = nickel, Sn = tin, Pb = lead• n/a = not applicable
MLCC END TERMINATION PHYSICAL CHARACTERISTICS
P/NTERMCODE
THICK FILM END TERMINATION
BARRIER TERMINATION TERMINATION FINISH
MATERIAL THICKNESS (INCHES)
Ni PLATE THICKNESS
(MICROINCHES)
Sn PLATE THICKNESS
(MICROINCHES)
Sn/Pb PLATE THICKNESS
(MICROINCHES)
Sn/PbSOLDER COAT
THICKNESS (MICROINCHES)
CONTENT OF LEAD
F, M Ag / Pd 0.001 min. n/a n/a n/a n/a n/a
E Ag / Pd 0.001 min. n/a n/a n/a n/a n/a
N Ag / Pd 0.0012 min. n/a n/a n/a n/a n/a
C Ag 0.001 min. n/a 100 min. n/a n/a n/a
W, X, Y Ag 0.001 min. 50 min. 100 min. n/a n/a n/a
L, Z Ag 0.001 min. 50 min. n/a 100 min. n/a 4 % min.
U Ag 0.001 min. 50 min. n/a n/a 60 min. 4 % min.
B Polymer 0.003 min. 50 min. 100 min. n/a n/a n/a
Revision: 27-Jan-15 271 Document Number: 45063For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Test Procedures and Requirementswww.vishay.com Vishay
Surface Mount Multilayer Chip Capacitorsfor Commodity Solutions
Below tables are test procedures and requirements unless specified in detail datasheet.
VJ....W1BC TEST PROCEDURES AND REQUIREMENTSTEST PROCEDURE REQUIREMENTS
1) Visual and mechanical
• No remarkable defect• Dimensions should confirm to individual specification sheet
2) Capacitance
Class 1: C0G (NP0)Cap. 1000 pF; 1.0 VRMS ± 0.2 VRMS;1 MHz ± 10 %Cap. > 1000 pF; 1.0 VRMS ± 0.2 VRMS;1 kHz ± 10 %
Class 2: X7R, X5R, Y5VCap. 10 μF; 1.0 VRMS ± 0.2 VRMS;1 kHz ± 10 % (1)
Cap. > 10 μF; 0.5 VRMS ± 0.2 VRMS;120 Hz ± 20 %
Note(1)Test conditions
0.5 VRMS ± 0.2 VRMS; 1 kHz ± 10 %
X7R:0603: 2.2 μF/10 V0805: 10 μF/6.3 V and 10 V
X5R: 0201: 220 nF/6.3 V0402: 4.7 μF/6.3 V0402: 2.2 μF/10 V0603: 10 μF/6.3 V
• Shall not exceed the limits given in the detailed specification
3) Q/DF (dissipationfactor)
C0G (NP0): Cap. 30 pF: Q 1000Cap. < 30 pF: Q400 + 20 C X5R, X7R:RATED VOLTAGE DF EXCEPTION OF DF
50 V 2.5 %
3 % 0201 (50 V); 0603 0.047 μF;0805 0.18 μF; 1206 0.47 μF
5 % 1210 4.7 μF
10 % 0603 1 μF; 0805 1 μF;1206 2.2 μF; 1210 10 μF
35 V 3.5 % 10 % 0805 2.2 μF; 1210 10 μF
25 V 3.5 %
5 % 0201 0.01 μF; 0805 1 μF;1210 10 μF
7 % 0603 0.33 μF; 1206 4.7 μF
10 %0402 0.10 μF; 0603 0.47 μF;0805 2.2 μF; 1206 6.8 μF;1210 22 μF
16 V 3.5 %
5 %0201 0.01 μF; 0402 0.033 μF;0603 0.15 μF; 0805 0.68 μF;1206 2.2 μF; 1210 4.7 μF
10 %0402 0.22 μF; 0603 0.68 μF;0805 2.2 μF; 1206 4.7 μF;1210 22 μF
10 V 5 %10 %
0201 0.012 μF; 0402 0.33 μF;0603 0.33 μF; 0805 2.2 μF;1206 2.2 μF; 1210 22 μF
15 % 0201 0.1 μF; 0402 1 μF
6.3 V 10 %15 %
0201 0.1 μF; 0402 1 μF;0603 10 μF; 0805 4.7 μF;1206 47 μF; 1210 100 μF
20 % 0402 2.2 μF4 V 15 % - -Y5V:RATED VOLTAGE DF EXCEPTION OF DF
50 V 5 % 7 % 0603 0.1 μF; 0805 0.47 μF;1206 4.7 μF
35 V 7 % - -
25 V 5 %7 %
0402 0.047 μF; 0603 0.1 μF;0805 0.33 μF; 1206 1 μF;1210 4.7 μF
9 % 0402 0.068 μF; 0603 0.47 μF;1206 4.7 μF; 1210 22 μF
16 VC < 1.0 μF 7 %
9 % 0402 0.068 μF; 0603 0.68 μF
12.5 % 0402 0.22 μF
16 VC 1.0 μF 9 % 12.5 % 0603 2.2 μF; 0805 3.3 μF;
1206 10 μF; 1210 22 μF
10 V 12.5 % 20 % 0402 0.47 μF
6.3 V 20 % - -
Revision: 27-Mar-13 272 Document Number: 28545For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Test Procedures and Requirementswww.vishay.com Vishay
VJ....W1BC TEST PROCEDURES AND REQUIREMENTSTEST PROCEDURE REQUIREMENTS
4) Dielectricstrength
• To apply voltage ( 100 V) 250 %• Duration: 1 s to 5 s• Charge and discharge current less
than 50 mA
• No evidence of damage or flash-over during test• To apply voltage
200 V to 300 V 2 times VDC500 V to 999 V 1.5 times VDC1000 V to 3000 V 1.2 times VDC
• Cut-off, set at 10 mA• TEST = 15 s• RAMP = 0
5) Insulationresistance
Rated voltage 100 V: To apply rated voltage for max. 120 s
10 G or R x C 500F whichever is smaller
Class 2 (X5R, X7R, Y5V):
RATED VOLTAGE INSULATION RESISTANCE
100 V: X7R
10 G or R x C 100 Fwhichever is less
50 V: 0603 1 μF; 0805 1 μF;1206 2.2 μF; 1210 4.7 μF
35 V: 0805 2.2 μF; 1210 10 μF
25 V: 0402 1 μF; 0603 2.2 μF;0805 2.2 μF; 1206 10 μF;1210 10 μF
16 V: 0402 0.22 μF; 0603 1 μF;0805 2.2 μF; 1206 10 μF;1210 47 μF
10 V: 0201 47 nF; 0402 0.47 μF;0603 0.47 μF; 0805 2.2 μF;1206 4.7 μF; 1210 47 μF
6.3 V; 4 V
Rated voltage: 200 V to 630 V
To apply rated voltage(500 V max.) for 60 s
10 G or R x C > 100 F whichever is smaller
Rated voltage: 630 V
To apply 500 V for 60 s 10 G
6) Temperaturecoefficient
With no electrical load:
T.C. Operating Temp. T.C. Capacitance change
C0G (NP0) - 55 °C to 125 °C at 25 °C C0G (NP0) Within ± 30 ppm/°C
X7R - 55 °C to 125 °C at 25 °C X7R Within ± 15 %
X5R - 55 °C to 85 °C at 25 °C X5R Within ± 15 %
Y5V - 25 °C to 85 °C at 20 °C Y5V Within + 30 %/- 80 %
7) Adhesive strengthof termination
• Pressurizing force:0201: 2N0402 and 0603: 5 N> 0603: 10 N
• Test time 10 s ± 1 s
• No remarkable damage or removal of the terminations
8) Vibrationresistance
• Vibration frequency: 10 Hz/min to 55 Hz/min
• Total amplitude: 1.5 mm• Test time: 6 h (2 h each in
3 mutually perpendicular directions)
• No remarkable damage• Capacitance change and Q/DF: to meet initial specification
9) Solderability • Solder temperature: 235 °C ± 5 °C• Dipping time: 2 s ± 0.5 s
95 % minimum coverage of all metallized area
Revision: 27-Mar-13 273 Document Number: 28545For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Test Procedures and Requirementswww.vishay.com Vishay
VJ....W1BC TEST PROCEDURES AND REQUIREMENTSTEST PROCEDURE REQUIREMENTS
10) Bending test
• The middle part of the substrate shallbe pressurized by means of thepressurizing rod at a rate of about1 mm per s until the deflectionbecomes 1 mm and then the pressureshall be maintained for 5 s ± 1 s
• Measurement to be made afterkeeping at room temperature for24 h ± 2 h
• No remarkable damage• Capacitance change:
C0G (NP0): within ± 5.0 % or ± 0.5 pF whichever is largerX7R, X5R: within ± 12.5 %Y5V: within ± 30 %
(This capacitance change means the change of capacitance under specified flexure of substrate from the capacitance measured before the test)
11) Resistance tosoldering heat
• Solder temperature: 260 °C ± 5 °C• Dipping time: 10 s ± 1 s• Preheating: 120 °C to 150 °C for
1 min before immerse the capacitorin a eutectic solder
• Before initial measurement(class 2 only):Perform 150 °C + 0 °C/ - 10 °C for 1 h and then set for 24 h ± 2 h at roomtemperature
• Measurement to be made after keepingat room temperature for 24 h ± 2 h
• No remarkable damage• Capacitance change:
C0G (NP0): within ± 2.5 % or ± 0.25 pF whichever is largerX7R, X5R: within ± 7.5 %Y5V: within ± 20 %
• Q/DF, I.R. and dielectric strength: To meet initial requirements• 25 % maximum leaching on each edge
12) Temperaturecycle
• Conduct the 5 cycles according to thetemperature and time
• No remarkable damage• Capacitance change:
C0G (NP0): within ± 2.5 % or ± 0.25 pF whichever is largerX7R, X5R: within ± 7.5 %Y5V: within ± 20 %
• Q/DF, I.R. and dielectric strength: To meet initial requirements
Step Temperature (°C) Time (min.)
1Min. operating temp.
+ 0/- 330 ± 3
2 Room temperature 2 ~ 3
3Max. operating temp.
+ 3/- 030 ± 3
4 Room temperature 2 ~ 3
• Before initial measurement (class 2 only):Perform 150 °C + 0 °C/- 10 °C for 1 hand then set for 24 h ± 2 h at roomtemperature
• Measurement to be made afterkeeping at room temperature for 24 h ± 2 h
Revision: 27-Mar-13 274 Document Number: 28545For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Test Procedures and Requirementswww.vishay.com Vishay
VJ....W1BC TEST PROCEDURES AND REQUIREMENTSTEST PROCEDURE REQUIREMENTS
13) Humidity(damp heat)steady state
• Test temperature: 40 °C ± 2 °C• Humidity: 90 % to 95 % RH• Test time: 500 h + 24 h/- 0 h• Before measurement (class 2
only): Perform 150 °C + 0 °C/- 10 °C for 1 h and then set for 24 h ± 2 h at room temperature
• Measurement to be made after keeping at room temperature for 24 h ± 2 h
• No remarkable damage• Capacitance change:
C0G (NP0): within ± 5.0 % or ± 0.5 pF whichever is largerX7R, X5R: 10 V within ± 12.5 %; 6.3 V, within ± 25 %Y5V: 10 V within ± 30 %, 6.3 V within + 30 %/- 40 %
• Q/DF value:C0G (NP0): more than 30 pF: Q350 10 pF C 30 pF: Q275 + 2.5 C;Less than 10 pF: Q200 + 10 C
X5R, X7R:RATEDVOLTAGE DF EXCEPTION OF DF
50 V 3 %
6 % 0201 (50 V); 0603 0.047 μF; 0805 0.18 μF; 1206 0.47 μF
10 % 1210 4.7 μF
20 % 0603 1 μF; 0805 1 μF; 1206 2.2 μF;1210 10 μF
35 V 5 % 20 % 0805 2.2 μF; 1210 10μF
25 V 5 %
10 % 0201 0.01 μF; 0805 1 μF; 1210 10 μF14 % 0603 0.33 μF; 1206 4.7 μF
15 % 0402 0.10 μF; 0603 0.47 μF; 0805 2.2 μF; 1206 6.8 μF; 1210 22 μF
16 V 5 %10 % 0603 0.15 μF; 0805 0.68 μF; 1206 2.2 μF;
1210 4.7 μF
15 % 0201 0.01 μF; 0402 0.033 μF; 0603 0.68 μF; 0805 2.2 μF; 1206 4.7 μF; 1210 22 μF
10 V 7.5 %15 % 0201 0.012 μF; 0402 0.33 μF; 0603 0.33 μF;
0805 2.2 μF; 1206 2.2 μF; 1210 22 μF20 % 0201 0.1 μF; 0402 1 μF
6.3 V 15 % 30 %0201 0.1 μF; 0402 1 μF;0603 10 μF; 0805 4.7 μF;1206 47 μF; 1210 100 μF
4 V 20 % - -Y5V:RATEDVOLTAGE DF EXCEPTION OF DF
50 V 7.5 % 10 % 0603 0.1 μF; 0805 0.47 μF; 1206 4.7 μF35 V 10 % - -
25 V 7.5 %10 % 0402 0.047 μF; 0603 0.1 μF; 0805 0.33 μF;
1206 1 μF; 1210 4.7 μF
15 % 0402 0.068 μF; 0603 0.47 μF; 1206 4.7 μF; 1210 22 μF
16 VC < 1.0 μF 10 %
12.5 % 0402 0.068 μF; 0603 0.68 μF20 % 0402 0.22 μF
16 VC 1.0 μF 12.5 % 20 % 0603 2.2 μF; 0805 3.3 μF;
1206 10 μF; 1210 22 μF10 V 20 % 30 % 0402 0.47 μF6.3 V 30 % - -• I.R.: 10 V: 1 G or R x C 50 F whichever is smaller CLASS 2 (X5R, X7R, Y5V):
RATED VOLTAGE INSULATION RESISTANCE
100 V: X7R
1 G or R x C 10 F whichever is less
50 V: 0603 1 μF; 0805 1 μF; 1206 2.2 μF;1210 4.7 μF
35 V: 0805 2.2 μF; 1210 10 μF25 V: 0402 1 μF; 0603 2.2 μF; 0805 2.2 μF;
1206 10 μF; 1210 10 μF16 V: 0402 0.22 μF; 0603 1 μF; 0805 2.2 μF;
1206 10 μF; 1210 47 μF10 V: 0201 47 nF; 0402 0.47 μF; 0603 0.47 μF;
0805 2.2 μF; 1206 4.7 μF; 1210 47 μF6.3 V; 4 V
Revision: 27-Mar-13 275 Document Number: 28545For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Test Procedures and Requirementswww.vishay.com Vishay
VJ....W1BC TEST PROCEDURES AND REQUIREMENTSTEST PROCEDURE REQUIREMENTS
14) Humidity (damp heat)load
• Test temperature: 40 °C ± 2 °C• Humidity: 90 % ~ 95 % RH• Test time: 500 h + 24 h/- 0 h• To apply voltage: rated voltage
(max. 500 V)• Before initial measurement
(class 2 only): Perform 150 °C + 0 °C/- 10 °C for 1h and then set for 24 h ± 2 h at room temperature
• Measurement to be made afterkeeping at room temperaturefor 24 h ± 2 h
• No remarkable damage• Capacitance change:
C0G (NP0): within± 7.5 % or ± 0.75 pF whichever is larger.X7R, X5R: 10 V within ± 12.5 %; 6.3 V, with ± 25 %Y5V: 10 V within ± 30 %; 6.3 V, within + 30 %/- 40 %
• Q/DF value: C0G (NP0)Cap 30 pF: Q 200;Cap < 30 pF: Q 100 + 10/3 C
X5R, X7R:RATEDVOLTAGE DF EXCEPTION OF DF
50 V 3 %
6 % 0201 (50 V); 0603 0.047 μF; 0805 0.18 μF;1206 0.47 μF
10 % 1210 4.7 μF
20 % 0603 1 μF; 0805 1 μF; 1206 2.2 μF;1210 10 μF
35 V 5 % 20 % 0805 2.2 μF; 1210 10 μF
25 V 5 %
10 % 0201 0.01 μF; 0805 1 μF; 1210 10 μF
14 % 0603 0.33 μF; 1206 4.7 μF
15 % 0402 0.10 μF; 0603 0.47 μF; 0805 2.2 μF; 1206 6.8 μF; 1210 22 μF
16 V 5 %10 % 0603 0.15 μF; 0805 0.68 μF; 1206 2.2 μF;
1210 4.7μF
15 % 0201 0.01 μF; 0402 0.033 μF; 0603 0.68 μF;0805 2.2 μF; 1206 4.7 μF; 1210 22 μF
10 V 7.5 %15 % 0201 0.012 μF; 0402 0.33 μF; 0603 0.33 μF;
0805 2.2 μF; 1206 2.2 μF; 1210 22 μF
20 % 0201 0.1 μF; 0402 1 μF
6.3 V 15 % 30 % 0201 0.1 μF; 0402 1 μF; 0603 10 μF;0805 4.7 μF; 1206 47 μF; 1210 100 μF
4 V 20 % - -
Y5V:RATEDVOLTAGE DF EXCEPTION OF DF
50 V 7.5 % 10 % 0603 0.1 μF; 0805 0.47 μF; 1206 4.7 μF
35 V 10 % - -
25 V 7.5 %10 % 0402 0.047 μF; 0603 0.1 μF; 0805 0.33 μF;
1206 1 μF; 1210 4.7 μF
15 % 0402 0.068 μF; 0603 0.47 μF; 1206 4.7 μF; 1210 22 μF
16 VC < 1.0 μF 10 %
12.5 % 0402 0.068 μF; 0603 0.68 μF
20 % 0402 0.22 μF
16 VC 1.0 μF 12.5 % 20 % 0603 2.2 μF; 0805 3.3 μF; 1206 10 μF;
1210 22 μF
10 V 20 % 30 % 0402 0.47 μF
6.3 V 30 % - -
• I.R.: 10 V: 500 M or 25 F whichever is smaller
CLASS 2 (X5R, X7R, Y5V):
RATED VOLTAGE INSULATION RESISTANCE
100 V: X7R
500 M orR x C 5 Fwhichever is less
50 V: 0603 1 μF; 0805 1 μF; 1206 2.2 μF; 1210 4.7 μF
35 V: 0805 2.2 μF; 1210 10 μF
25 V: 0402 1 μF; 0603 2.2 μF; 0805 2.2 μF; 1206 10 μF;1210 10 μF
16 V: 0402 0.22 μF; 0603 1 μF; 0805 2.2 μF; 1206 10 μF; 1210 47 μF
10 V: 0201 47 nF; 0402 0.47 μF; 0603 0.47 μF;0805 2.2 μF; 1206 4.7 μF; 1210 47 μF
6.3 V; 4 V
Revision: 27-Mar-13 276 Document Number: 28545For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Test Procedures and Requirementswww.vishay.com Vishay
VJ....W1BC TEST PROCEDURES AND REQUIREMENTSTEST PROCEDURE REQUIREMENTS
15) Hightemp. load(endurance)
• Test temperature: C0G (NP0), X7R/X7E: 125 °C ± 3 °CX5R, Y5V: 85 °C ± 3 °C
• To apply voltage:
• No remarkable damage• Capacitance change:
C0G (NP0): ± 3.0 % or ± 0.3 pF whichever is larger.X7R, X5R: 10 V within ± 12.5 %; 6.3 V, with ± 25 %Y5V: 10 V within ± 30 %; 6.3 V, within + 30 % to - 40 %
• Q/DF value:C0G (NP0): More than 30 pF, Q 35010 pF C < 30 pF: Q275 C + 2.5 C;Less than 10 pF: Q 200 C + 10 C
(1.1) 100 % of rated voltage for below range X5R, X7R:
SIZE DIELECTRIC RATED VOLTAGE
CAP.RANGE
RATEDVOLTAGE DF EXCEPTION OF DF
0201 X5R/X7R 6.3 V, 10 V C 0.1 μF
50 V 3 %
6 % 0201 (50 V); 0603 0.047 μF; 0805 0.18 μF;1206 0.47 μF
0402 X5R/X7R 6.3 V, 10 V C 1 μF 10 % 1210 4.7 μF
0603 X5R/X7R 6.3 V, 10 V C 4.7 μF 20 % 0603 1 μF; 0805 1 μF; 1206 2.2 μF;1210 10 μF
0805 X5R/X7R 6.3 V C 22 μF 35 V 5 % 20 % 0805 2.2 μF; 1210 10 μF1206 X5R/X7R 6.3 V C 47 μF
25 V 5 %
10 % 0201 0.01 μF; 0805 1 μF; 1210 10 μF(1.2) 6.3 V or C 10 μF: 150 % of rated voltage 14 % 0603 0.33 μF; 1206 4.7 μF
(2)10 V UR < 500 V: 200 % of rated voltage 15 % 0402 0.10 μF; 0603 0.47 μF; 0805 2.2 μF;1206 6.8 μF; 1210 22 μF
150 % of rated voltage for below range:16 V 5 %
10 % 0603 0.15 μF; 0805 0.68 μF; 1206 2.2 μF;1210 4.7 μF
SIZE DIELECTRIC RATEDVOLTAGE
CAP.RANGE 15 % 0201 0.01 μF; 0402 0.033 μF; 0603 0.68 μF;
0805 2.2 μF; 1206 4.7 μF; 1210 22 μF
0402X5R/X7R 10 V, 16 V,
25 V C 0.22 μF10 V 7.5 %
15 % 0201 0.012 μF; 0402 0.33 μF; 0603 0.33 μF;0805 2.2 μF; 1206 2.2 μF; 1210 22 μF
Y5V 16 V C 0.47 μF 20 % 0201 0.1 μF; 0402 1 μF
0603X5R/X7R 10 V, 16 V C 1.0 μF 6.3 V 15 % 30 % 0201 0.1 μF; 0402 1 μF; 0603 10 μF;
0805 4.7 μF; 1206 47 μF; 1210 100 μFY5V 16 V C 2.2 μF 4 V 20 % - -
0805X5R/X7R 10 V C 4.7 μF Y5V:Y5V 16 V C 4.7 μF RATED
VOLTAGE DF EXCEPTION OF DF (3) 500 V: 150 % of rated voltage(4) UR 630 V: 120 % of rated voltage
• Test time: 1000 h + 24 h/- 0 h• Before measurement (class 2 only): Perform
150 °C + 0 °C/- 10 °C for 1 h and then set for 24 h ± 2 h at room temperature
• Measurement to be made after keeping atroom temperature for 24 h ± 2 h
50 V 7.5 % 10 % 0603 0.1 μF; 0805 0.47 μF; 1206 4.7 μF
35 V 10 % - -
25 V 7.5 %10 % 0402 0.047 μF; 0603 0.1 μF; 0805 0.33 μF;
1206 1 μF; 1210 4.7 μF
15 % 0402 0.068 μF; 0603 0.47 μF; 1206 4.7 μF;1210 22 μF
16 VC < 1.0 μF 10 %
12.5 % 0402 0.068 μF; 0603 0.68 μF20 % 0402 0.22 μF
16 VC 1.0 μF 12.5 % 20 % 0603 2.2 μF; 0805 3.3 μF; 1206 10 μF;
1210 22 μF10 V 20 % 30 % 0402 0.47 μF6.3 V 30 % - -• I. R.: 10 V: 1 G or 50 F whichever is smallerCLASS 2 (X5R, X7R, Y5V):
RATED VOLTAGE INSULATIONRESISTANCE
100 V: X7R
1 G or R x C 10 Fwhichever is less
50 V: 0603 1 μF; 0805 1 μF; 1206 2.2 μF;1210 4.7 μF35 V: 0805 2.2 μF; 1210 10 μF25 V: 0402 1 μF; 0603 2.2 μF; 0805 2.2 μF;1206 10 μF; 1210 10 μF16 V: 0402 0.22 μF; 0603 1 μF; 0805 2.2 μF;1206 10 μF; 1210 47 μF10 V: 0201 47 nF; 0402 0.47 μF; 0603 0.47 μF;0805 2.2 μF; 1206 4.7 μF; 1210 47 μF6.3 V; 4 V
Revision: 27-Mar-13 277 Document Number: 28545For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Soldering and Footprint Designwww.vishay.com Vishay
Surface Mount Multilayer Ceramic Chip Capacitorsfor Commodity Applications
RECOMMENDED SOLDERING CONDITIONSLead (Pb)-free terminated MLCCs are not only used on SMT with lead (Pb)-free solder paste, but also suitable to be used withlead-containing solder paste. In case the optimized solder joint is requested, increasing soldering time, temperature andconcentration of N2 within the oven are recommended.
SOLDERING PROFILES
Recommended IR reflow soldering profile for SMT process with SnAgCu series solder paste
Recommended wave soldering profile for SMT process with SnAgCu series solder
280260
2040
80100120
60
140160180
220240
200
120 s 120 s 120 s
60 s to 90 sTime
SnAgCu solder paste
3 °C/s
4 °C/s4 °C/s
Min. temp.
Max. temp.
Peak temperature: 280 °C max.Duration time: > 260 °C,10 s max. > 215 °C, 60 s to 90 s
Tem
per
atur
e in
°C
< 100 s
Over 60 s at least by natural cooling
3 s to 5 s
Time
Tem
per
atur
e in
°C
Total contact time
100
50
0
200
150
250
260 °C
120 °C
4 °C/s max.
150 °C/s max.
Revision: 01-Apr-11 278 Document Number: 45017For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VJ....W1BC Soldering and Footprint Designwww.vishay.com Vishay
FOOTPRINT DESIGNCircuit board design first steps are to consider how the surface mount board will be manufactured. The manufacturing processdetermines the necessary dimensions of the solder land, the minimum spacing between components, the area underneath theSMD where tracks may be laid down and the required component orientation during wave soldering. Therefore a footprintrelated to the manufacturing process with all this information is an essential tool for SMD circuit board design.
Footprint details depend on following parameters:• Component dimensions and tolerance as given in the component data• Board dimensional accuracy• Placement accuracy of the component with respect to the solder lands on the board• Solder paste position tolerances with respect to the solder lands (for reflow soldering only)• The soldering parameters• Solder resist position tolerances with respect to the solder lands• Solder joint parameters for reliable joints
TYPICAL SMD FOOTPRINT
REFLOW SOLDERING
SIZEFOOTPRINT DIMENSIONS IN mm PROCESSING
REMARKSPLACEMENTACCURACYA B C D E F G
0201 0.65 0.23 0.21 0.30 n/a 0.90 0.60
Reflow or hot plate soldering
± 0.050402 1.50 0.50 0.50 0.50 0.10 1.75 0.95 ± 0.150603 2.30 0.70 0.80 0.80 0.20 2.55 1.40 ± 0.250805 2.80 1.00 0.90 1.30 0.40 3.05 1.85 ± 0.251206 4.00 2.20 0.90 1.60 1.60 4.25 2.25 ± 0.251210 4.00 2.20 0.90 2.50 1.60 4.25 3.15 ± 0.25
WAVE SOLDERING
SIZEFOOTPRINT DIMENSIONS IN mm PROPOSED NUMBER
AND DIMENSIONS OF DUMMY TRACKS
PLACEMENTACCURACYA B C D E F G
0603 2.40 1.00 0.70 0.80 0.20 3.10 1.90 1 x (0.20 x 0.80) ± 0.100805 3.20 1.40 0.90 1.30 0.36 4.10 2.50 1 x (0.30 x 1.30) ± 0.151206 4.80 2.30 1.25 1.70 1.25 5.90 3.20 3 x (0.25 x 1.70) ± 0.251210 5.30 2.30 1.50 2.60 1.25 6.30 4.20 3 x (0.25 x 2.60) ± 0.25
FOOTPRINT FOR MLCC CHIP ARRAYSIZE DIMENSIONS IN mm
A 2.85 + 0.10/- 0.05
B 0.45 ± 0.05
D 0.80 ± 0.10
P 0.80
F 3.10 ± 0.30
Occupied area
Solder land/Solder paste pattern
Solder resist pattern
Tracks or Dummy tracks (for wave soldering only)
AF
BC
G
DE
BA
P
D F
Revision: 01-Apr-11 279 Document Number: 45017For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VSE-DB0097-1502DATA BOOK
VISHAY INTERTECHNOLOGY, INC.
THE AMERICAS
UNITED STATESVISHAY AMERICAS ONE GREENWICH PLACE SHELTON, CT 06484 UNITED STATES PH: +1-402-563-6866 FAX: +1-402-563-6296
ASIA
SINGAPOREVISHAY INTERTECHNOLOGY ASIA PTE LTD.37A TAMPINES STREET 92 #07-00SINGAPORE 528886 PH: +65-6788-6668 FAX: +65-6788-0988
P.R. CHINAVISHAY CHINA CO., LTD.15D, SUN TONG INFOPORT PLAZA55 HUAI HAI WEST ROADSHANGHAI 200030 P.R. CHINAPH: +86-21-5258 5000FAX: +86-21-5258 7979
JAPANVISHAY JAPAN CO., LTD.SHIBUYA PRESTIGE BLDG. 4F 3-12-22, SHIBUYA SHIBUYA-KU TOKYO 150-0002 JAPAN PH: +81-3-5466-7150 FAX: +81-3-5466-7160
EUROPE
GERMANYVISHAY ELECTRONIC GMBHDR.-FELIX-ZANDMAN-PLATZ 1 95100 SELB GERMANY PH: +49-9287-71-0 FAX: +49-9287-70435 FRANCEVISHAY S.A.199, BLVD DE LA MADELEINE 06003 NICE, CEDEX 1 FRANCE PH: +33-4-9337-2727 FAX: +33-4-9337-2726 UNITED KINGDOMVISHAY LTD.SUITE 7A, TOWER HOUSEST. CATHERINE’S COURTSUNDERLAND ENTERPRISE PARKSUNDERLAND SR5 3XJ UNITED KINGDOMPH: +44-191-516-8584FAX: +44-191-549-9556
Visit www.vishay.com for product information or select below for a current list of sales offices, representatives, and distributors.
SEMICONDUCTORS: Rectifiers • High-Power Diodes and Thyristors • Small-Signal Diodes • Zener and Suppressor Diodes • FETs • Optoelectronics • ICs • Modules
PASSIVE COMPONENTS:Resistive Products • Magnetics • Capacitors
© Copyright 2015 Vishay Intertechnology, Inc.® Registered trademarks of Vishay Intertechnology, Inc.All rights reserved. Printed in Germany. Specifications subject to change without notice.
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VISHAY PRODUCTS
WORLD HEADQUARTERS Vishay Intertechnology, Inc. | 63 Lancaster Avenue Malvern, PA 19355-2143 | USA
WO
RL
DW
IDE
SA
LE
S C
ON
TA
CT
S