RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 1 08.27.18

Vive Maestro Wireless Dimmers and SwitchesThe Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation.Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads.

These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time. System reprogramming will be required. For a complete list of features supported with the Vive hub, see specification submittal 369902.

Note for Replacement: MRF2S - the “S” model can replace the non-”S” model.

Features• TheMaestroWirelesssolutionprovidesdimming/

switchingofmultipleloadtypes,occupancy/vacancysensing, and daylight harvesting.

• LutronpatentedClearConnectRFTechnologyworksthrough walls and floors.

• IncorporatesadvancedfeaturessuchasfadeON/fadeOFF,high-endtrim,andrapidfull-ON (a Vive hub is required to set high-end trim).

• ControlsincludeFrontAccessibleServiceSwitch(FASS)forsafelampreplacement.

• Two-wiredimmersandswitchesavailableforretrofitapplications.

• Powerfailurememory:Ifpowerisinterrupted,thecontrol will return to its previously set level prior to interruption.

Receiving DevicesMaestro Wireless Controls

Neutral and Non-Neutral Dimmers

Neutral and Non-Neutral Switches

Transmitting DevicesRadio Powr Savr Sensors

Pico Remote Controls

Ceiling-Mounted Occupancy and Vacancy Sensors

Wall-Mounted Occupancy and Vacancy Sensors

Daylight Sensors

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 2 08.27.18

Maestro Wireless Dimmers

Models AvailableDimmersCFL / LED/Halogen / IncandescentMRF2S-6CL-XX 1 150WCFL/LEDDimmer; 600W/600VAIncandescent,120V~

MRF2S-6ND-120-XX 1,2 600W/600VASpec-GradeNeutralWireDimmer,120V~ 150WCFL/LEDDimmer

Electronic Low-Voltage DimmerMRF2S-6ELV120-XX1 600WELVDimmer120V~ (neutral required) 150WCFL/LEDDimmer

Companion DimmersClaro Gloss FinishesMA-R-XX1,2 Companion Dimmer 120 V~

Satin Colors Satin FinishesMSC-AD-XX1 Companion Dimmer 120 V~

1 “XX”inthemodelnumberrepresentscolor/finishcode.SeeColors and Finishes at end of document.2 BAA-compliantmodelnumbersavailable.Adda“U”prefixtothemodelnumber.

Dimmer

Companion Dimmer

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 3 08.27.18

Ganging and DeratingWhencombiningcontrolsinthesamewallbox,deratingisrequired.Dimmer Load Type and Capacity

No Neutral Required

A B B B C B

Control Voltage Load Type Minimum LoadMaximum Load

A: Not Ganged B: End of Gang C: Middle of Gang

MRF2S-6CL 1,2,3 120 V~CFL/LED See lamp list See Mixing Lamp TypesIncandescent/Halogen 50 W 600 W 500 W 400 W

Note:DonotmixELVandMLVloadtypesonasinglecontrol.1 DimmerLoadType:

• MRF2S-6CLisdesignedforusewithpermanently-installedincandescent,CFL,LED,ortungstenhalogenonly.• MRF2S-6ND-120isdesignedforusewithpermanently-installedincandescent,CFL,LED,magneticlow-voltage,ortungstenhalogenonly.CancontrolPowerModules(PHPM-

PA-DV,PHPM-3F-DV-WH,PHPM-WBX-DV-WH,andGRX-TVI)andlegacyinterfacesHi-Power2•4•6Boosters(HP-2,HP-4,HP-6).• MRF2S-6ELV120isdesignedforusewithpermanently-installedelectroniclow-voltage,incandescent,CFL,LEDortungsten/halogenonly.Donotinstalldimmerstocontrol

receptacles or motor-operated appliances.2 Low-VoltageApplications:

• UseMRF2S-6ND-120withmagnetic(coreandcoil)low-voltagetransformersonly.Notforusewithelectronic(solid-state)low-voltagetransformers.• UseMRF2S-6ELV120withelectronic(solid-state)low-voltagetransformersonly.Operationofalow-voltagecircuitwithlampsinoperativeorremovedmayresultintransformer

overheatingandprematurefailure.Lutronstronglyrecommendsthefollowing:– Do not operate low-voltage circuits without operative lamps in place.– Replaceburned-outlampsasquicklyaspossible.– Usetransformersthatincorporatethermalprotectionorfusedtransformerprimarywindingstopreventtransformerfailureduetoovercurrent.

• SeeApplicationNote#559fordimminglowvoltageLEDs.3 BAA-compliantmodelnumbersavailable.Adda“U”prefixtothemodelnumber.

Mixing Lamp TypesMixinglamptypes(usingacombinationofCFL/LED,andIncandescent/Halogenbulbs)andganging with other dimmers or electronic switches may reduce maximumwattage,asshown.

Example:Iffinsfromonesideofdimmerareremovedand you have two 24 W bulbs installed (total CFL Wattage = 48 W), you may add up to 300 W of incandescent or halogen lighting.

Do not remove outside fins on ends of ganged controls (shaded areas below)

A B B B C B

Total CFL/LED WattageTotal Incandescent/Halogen Wattage

A: Not Ganged B: End of Gang C: Middle of Gang

MRF2S-6CL0 W + 50 W – 600 W Or 50 W – 500 W Or 50 W – 400 W1 W – 25 W + 0 W – 500 W Or 0 W – 400 W Or 0 W – 300 W26 W – 50 W + 0 W – 400 W Or 0 W – 300 W Or 0 W – 200 W51 W – 75 W + 0 W – 300 W Or 0 W – 200 W Or 0 W – 100 W76 W – 100 W + 0 W – 200 W Or 0 W – 100 W Or 0 W – 50 W101 W – 125 W + 0 W – 100 W Or 0 W – 50 W Or 0 W126 W – 150 W + 0 W Or 0 W Or 0 W

Neutral Required

Control Voltage Load Type Minimum LoadMaximum Load

A: Not Ganged B: End of Gang C: Middle of Gang

MRF2S-6ELV1201,2 120 V~ELV 5 W 600 W 500 W 400 W

CFL/LED See lamp list See Mixing Lamp Types

MRF2S-6ND-120 1,2,3 120 V~

Incandescent/Halogen 25 W 600 W 500 W 400 W

MLV 2 25W/VA 450W/600VA 400W/500VA 300W/400VA

CFL/LED See lamp list See Mixing Lamp Types

Example:Ifadimmerisinstalledinlocation“B”aboveand there are two 24 W CFL bulbs installed (Total CFL Wattage = 48 W), you may add up to 300 W of incandescent or halogen lighting.

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 4 08.27.18

Maestro Wireless Switches

Models AvailableSwitchesLighting and motor loadsMRF2S-6ANS-XX1,2,4 6ALighting/3AFan(1/10HPmotor), ElectronicSwitch120 V~

MRF2S-8ANS120-XX1,2,4 8ALighting,5.8AFan(1/4HPmotor),Spec-Grade ElectronicSwitch120V~

MRF2S-8S-DV-XX 2,3,4 8ALighting,3AFan(1/10HPmotor,120V~ only), Spec-GradeElectronicSwitch120–277V~, no neutral wire required

Companion SwitchesClaro Gloss FinishesMA-AS-XX2,4 Companion Switch 120 V~

MA-AS-277-XX2,4 Companion Switch 277 V~

Satin Colors Satin FinishesMSC-AS-XX4 Companion Switch 120 V~

MSC-AS-277-XX4 Companion Switch 277 V~

1 Neutral wire required.

2 BAA-compliantmodelnumbersavailable.Adda“U”prefixtothemodelnumber.

3 MayrequireLUT-MLC(includedwithMRF2S-8S-DVmodels)toensureproperfunctionwithlow-wattageloadtypes. See page 11 for details.

4 “XX”inthemodelnumberrepresentscolor/finishcode.SeeColors and Finishes at end of document.

Switch

Companion Switch

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 5 08.27.18

Ganging and DeratingWhencombiningcontrolsinthesamewallbox,deratingisrequired.Switch Load Type and Capacity

No Neutral Required

A B B B C B

Control Voltage Load Type Minimum LoadMaximum Load

A: Not Ganged B: End of Gang C: Middle of Gang

MRF2S-8S-DV 1,5

120 – 277 V~ Incandescent/Halogen 25 W 8A 8A/7A4 7A120 – 277 V~ Fluorescent/LED/CFL 40W(LUT-MLC)3 8A 8A/7A4 7A120 V~ Fan Motor 0.4A 1/10HP(3A) 1/10HP(3A) 1/10HP(3A)

1 SwitchLoadType:• MRF2S-8ANS120isdesignedforusewithpermanently-installedlightingloadsandwithfanmotorloadsupto1/4HP(5.8A).

• MRF2S-8S-DVisdesignedforusewithpermanently-installedlightingloadsandwithfanmotorloadsupto1/10HP(3A,120V~ only).

• MRF2-6ANSisdesignedforusewithpermanently-installedlightingloadsandwithfanmotorloadsupto1/10HP(3A).

2 Forloadslargerthan8A(120V~),theMRF2S-8ANS120switchcanbeusedwiththePHPM-SW-DV-WHpowerbooster.

3 TheLUT-MLCensuresproperfunctionwithlow-wattagefluorescent,CFL,andLEDloadtypes.See page 11 for details.

4 Maximumloadfordouble-gangapplicationis8A.Triple-gangapplicationderatesmaximumloadto7A.

5 BAA-compliantmodelnumbersavailable.Adda“U”prefixtothemodelnumber.

Neutral Required

A B B B C B

Control Voltage Load Type Minimum LoadMaximum Load

A: Not Ganged B: End of Gang C: Middle of Gang

MRF2S-8ANS1201,2,5 120 V~Lighting 25 W 8A 6.5A 5AFan Motor 0.2A 1/4HP(5.8A) 1/4HP(5.8A) 1/6HP(4.4A)

MRF2-6ANS1 120 V~Lighting 25 W 6A 5A 3.5AFan Motor 0.2A 1/10HP(3A) 1/10HP(3A) 1/10HP(3A)

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 6 08.27.18

SpecificationsRegulatory Approvals

• UL® Listed.• cUL® Listed (MRF2S-6CL only).• CSACertified(exceptforMRF2S-6CL).• FCCApproved.ComplieswiththelimitsforaClassB

digital device, pursuant to Part 15 of the FCC Rules.• IndustryCanadaCertified.• Thefollowingmodelnumbershavebeentestedand

foundcompliantwithUL2043foruseinairhandlingspaces:MRF2S-6CL-GR,MRF2S-6ELV-GR, MRF2S-6ND-GR

PowerOperatingvoltage:

• 120V~50/60Hz(allmodels)• 277V~50/60Hz(MRF2S-8S-DV)

Environment• Ambientoperatingtemperature:32°Fto104°F

(0 °Cto40°C)• 0%to90%humidity,non-condensing.• Indooruseonly.• AlldriversandballastsusedwithVivewireless

controlsmustcomplywiththelimitsforaClassAdevice pursuant to Part 15 of the FCC Rules.

Key Design FeaturesDimmers

• Onasingle-tap,lightsfadeUPorDOWN.• Onadouble-tap,lightsgotofullON.• Lightlevelscanbefine-tunedbypressingand

holdingthedimmingrockeruntilthedesiredlightlevel is reached.

• Two-wiredimmersavailable.

Switches• Onasingle-tap,lightsturnONorOFF.• Two-wireswitchesavailable.

All RF Local Controls• Testedtowithstandelectrostaticdischargewithout

damageormemoryloss,inaccordancewithIEC61000-4-2.

• Testedtowithstandsurgevoltageswithout damage or loss of operation, in accordance with IEEEC62.41-1991RecommendedPracticeonSurgeVoltagesinLow-VoltageACPowerCircuits.

• Controlsalwaysoperatelocallyanddonotrequiresystem control.

• Powerfailurememory:shouldpowerbeinterrupted,the control will return to its previously-set level prior to the interruption when power is restored.

• Usesconventional3-wayand4-waywiring.• MultiplelocationcontrolfromDimmer/Switchandup

tonineCompanionDimmers/Switches.• UseLutronDesigner(ClaroandSatinColors)

wallplates or designer-style wallplates from other manufacturers. Wallplates are sold separately.

• LutronClaroandSatinColorswallplatessnaponwith no visible means of attachment.

• Requiresaone-gangU.S.wallbox;31⁄2 in (89 mm) deep recommended, 21⁄4 in (57 mm) deep minimum.

• Greenindicatorlights.

System Communications and Capacity• MaestroWirelesscontrolscommunicatewiththe

Pico remote controls and Radio Power Savr sensors through radio frequency (RF).

• Receiveswirelessinputsfromupto10Picoremotecontrols, 10 Radio Powr Savr occupancy/vacancysensors, and 1 Radio Powr Savr daylight sensor

• MaestroWirelesslocalcontrolsmustbelocatedwithin 60 ft (18 m) line-of-sight or 30 ft (9 m) through walls, of Radio Power Savr sensors. The 60 ft (18 m) range is not reduced by a ceiling tile obstruction.

• MaestroWirelesslocalcontrolsmustbelocatedwithin 60 ft (18 m) line-of-sight or 30 ft (9 m) through walls, of a Pico remote control. The 60 ft (18 m) range is not reduced by a ceiling tile obstruction.

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 7 08.27.18

WallplateAdapter/Wallplatepurchasedseparately

WallplateAdapter Wallplate

Wallbox

Control

AdapterMountingScrews

Control Mounting Screws

Mounting

DimensionsAlldimensionsareshownas:in(mm)

Side View

5/16(8)

1 1⁄8(30)

Front View

4 11⁄16(119)

2 15⁄16(75)

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 8 08.27.18

Operation

Status LEDsIndicatelightlevel;glowsoftlyasnight light when light is OFF

Dimming RockerPress to brightenPress to dim

TapswitchTapON/OFF;Double-tap:lightsgotofullON

FASSFrontAccessibleServiceSwitch

FASSFrontAccessibleServiceSwitch

FASS Front Accessible Service SwitchImportant Notice: To service load, removepowerbypullingtheFASSoutcompletelyoneithertheDimmer/SwitchorCompanionDimmer/Switch.Afterservicingload,pushtheFASSbackinfullyto restore power to the control.

Dimmer

TapswitchTapON/OFF

SwitchStatus LEDIndicatesloadstatus;glowssoftlyasnight light when light is OFF

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 9 08.27.18

1 When using controls in single location installations, tighten the blue terminal without any wires attached. Do not connect the blue terminal to any other wiring or to ground.

2 UptonineMaestroCompanionDimmersmaybeconnectedtotheMaestroWirelessDimmer.Totalblueterminalwirelengthmaybeupto250ft(76m).

Wiring DiagramsSingle-Location Dimmer Installation without NeutralMRF2S-6CL

Dimmer

Load

Brass

Black

Line/Hot

Green

Blue 1

Ground

Neutral

120 V~60Hz

Multi-Location Dimmer Installation without Neutral 2MRF2S-6CLwithMA-R/MSC-AD

Companion Dimmer Companion Dimmer Dimmer

BrassBrassBrass

BlackBlackBlack

Line/Hot

GreenGreenGreen

BlueBlueBlue

GroundGroundGround

Neutral

120 V~60Hz Load

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 10 08.27.18

1 When using controls in single location installations, tighten the blue terminal without any wires attached. Do not connect the blue terminal to any other wiring or to ground.

2 UptonineMaestroCompanionDimmers/SwitchesmaybeconnectedtotheMaestroWirelessDimmer/Switch.Totalblueterminalwirelengthmaybeupto250 ft (76 m).

3 Neutral-wireDimmers/SwitchesmustbeconnectedontheLoadsideofamulti-locationinstallation.

Wiring Diagrams (continued)

Multi-Location Dimmer / Switch Installation with Neutral 2,3

MRF2S-6ND-120and-6ELV120withMA-R/MSC-ADorMRF2S-8ANS120and-6ANSwithMA-AS/MSC-AS

Companion Dimmer/Switch

Companion Dimmer/Switch Dimmer/Switch

Brass

Silver

BrassBrass

BlackBlackBlack

Line/Hot

GreenGreenGreen

BlueBlueBlue

GroundGroundGround

Neutral

120 V~60Hz Load

Single-Location Dimmer / Switch Installation with NeutralMRF2S-6ND-120,-6ELV120,-8ANS120,and-6ANS

Dimmer/Switch

Load

Brass

Black

Silver

Line/Hot

Green

Blue 1

Ground

Neutral

120 V~60Hz

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 11 08.27.18

1 ALUT-MLCensuresproperfunctionwhenfluorescent,CFL,orLEDloadsareused.InstalltheLUT-MLCinsidealoadfixtureorinaseparateJ-boxwithinthecircuit.

2 When using controls in single-location installations, tighten the blue terminal without any wires attached. Do not connect the blue terminal to any other wiring or to ground.

3 UptonineMaestroCompanionSwitchesmaybeconnectedtotheMaestroWirelessSwitch.Totalblueterminalwirelengthmaybeupto250ft(76m).4 RequiresMA-AS/MSC-ASfor120V~applications,andMA-AS-277/MSC-AS-277for277V~ applications.

Single-Location Switch Installation with LUT-MLC 1MRF2S-8S-DV

Switch

Load LUT-MLC1

Brass

Black

Line/Hot

Green

Optional *

Blue 2

Ground

Neutral

120 V~60Hz or 277 V~60Hz

Multi-Location Switch Installation with LUT-MLC 1,2,3

MRF2S-8S-DVwithMA-AS/MA-AS-277orMSC-AS/MSC-AS-2774

Companion Switch Companion Switch Switch

BrassBrassBrass

BlackBlackBlack

Line/Hot

GreenGreenGreen

BlueBlueBlue

GroundGroundGround

Neutral

120 V~60Hz or 277 V~60Hz

Load LUT-MLC1

Optional *

Wiring Diagrams (continued)

* Optional Procedure: UsingLUT-MLCwithMRF2S-8S-DV-XX

•InstallMRF2S-8S-DV-XXfirstwithoutLUT-MLCtoseeifrequired.Checkforproblemswithload.

•Problemscanoccurwhenlow-wattageloadsareused (< 40 W).

•WatchforflickeringloadswhendimmerisinelectronicOFF state.

•Ifrequired,LUT-MLCcanbeinstalledbetweenswitchedhotandneutralinwallboxifneutralispresent,orinanyfixtureontheswitchedcircuit.

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 12 08.27.18

1 When using controls in single-location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring or to ground.2 UptonineMaestroCompanionSwitchesmaybeconnectedtotheMaestroWirelessSwitch.Totalblueterminalwirelengthmaybeupto250ft(76m).3 Neutral-wire Switches must be connected on the Load side of a multi-location installation.

Wiring Diagrams (continued)

Single-Location Switch Installation with Power Booster Single FeedMRF2S-8ANS120and-6ANSwithPHPM-SW-DV-WH

Switch

Brass Blue 1

Zone In

Black

Silver

Line/Hot

SwitchedLine/Hot

Line/Hot

NeutralNeutral

Neutral

Ground

Ground

Green

120 V~60Hz

Load

Multi-Location Switch Installation with Power Booster Single Feed 2,3

MRF2S-8ANS120and-6ANSwithMA-AS/MSC-ASandPHPM-SW-DV-WH

Companion Switch Switch

Brass BlueBlue

Zone In

Black

Silver

Line/Hot

SwitchedLine/Hot

Line/Hot

Brass

Black

NeutralNeutral

Neutral

Ground

Ground

Green

Ground

Green

120 V~60Hz

Load

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 13 08.27.18

Multi-Location Switch Installation with Power Booster Dual Feed 1,2

MRF2S-8ANS120and-6ANSwithMA-AS/MSC-ASandPHPM-SW-DV-WH

Companion Switch Switch

Brass BlueBlue

Zone In

Black

Silver

Line/Hot

Switched Line/Hot

Line/Hot

Brass

Black

NeutralNeutral

Neutral

Neutral

Ground

Ground

Green

Ground

Green

120 V~60Hz or 277 V~60Hz

120 V~60Hz

Load

Wiring Diagrams (continued)

Single-Location Switch Installation with Power Booster Dual FeedMRF2S-8ANS120and-6ANSwithPHPM-SW-DV-WH

Switch

Brass Blue 1

Zone In

Black

Silver

Line/Hot

Switched Line/Hot

Line/Hot

NeutralNeutral

Neutral

Neutral

Ground

Ground

Green

120 V~60Hz or 277 V~60Hz

120 V~60Hz

Load

1 When using controls in single-location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring or to ground.2 UptonineMaestroCompanionSwitchesmaybeconnectedtotheMaestroWirelessSwitch.Totalblueterminalwirelengthmaybeupto250ft(76m).3 Neutral-wire Switches must be connected on the Load side of a multi-location installation.

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 14 08.27.18

1 When using controls in single-location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring or to ground.2 UptonineMaestroCompanionDimmersmaybeconnectedtotheMaestroWirelessDimmer.Totalblueterminalwirelengthmaybeupto250ft(76m).3 Neutral-wire Dimmers must be connected on the Load side of a multi-location installation.

Wiring Diagrams (continued)

Single-Location Switch Installation with Power Booster Single FeedMRF2S-6ND-120withPHPM-PA-DV-WH

Dimmer

DH

Brass Blue 1

Zone In

Black

Silver

Line/Hot

SwitchedLine/Hot

Line/Hot

NeutralNeutral

Neutral

Ground

Ground

Green

120 V~60Hz

Load

Multi-Location Switch Installation with Power Booster Single Feed 2,3

MRF2S-6ND-120withMA-R/MSC-ADandPHPM-PA-DV-WH

Companion Dimmer Dimmer

DH

Brass BlueBlue

Zone In

Black

Silver

Line/Hot

SwitchedLine/Hot

Line/Hot

Brass

Black

NeutralNeutral

Neutral

Ground

Ground

Green

Ground

Green

120 V~60Hz

Load

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 15 08.27.18

1 When using controls in single-location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring or to ground.2 UptonineMaestroCompanionDimmersmaybeconnectedtotheMaestroWirelessDimmer.Totalblueterminalwirelengthmaybeupto250ft(76m).3 Neutral-wire Dimmers must be connected on the Load side of a multi-location installation.

Wiring Diagrams (continued)

Single-Location Switch Installation with Power Booster Single FeedMRF2S-6ND-120withPHPM-PA-DV-WH

Multi-Location Switch Installation with Power Booster Single Feed 2,3

MRF2S-6ND-120withMA-R/MSC-ADandPHPM-PA-DV-WH

Companion Dimmer Dimmer

Brass BlueBlue

Zone In

Black

Silver

Line/Hot

Switched Line/Hot

Line/Hot

Brass

Black

NeutralNeutral

Neutral

Neutral

Ground

Ground

Green

Ground

Green

120 V~60Hz or 277 V~60Hz

120 V~60Hz

Load

Dimmer

Brass Blue 1

Zone In

Black

Silver

Line/Hot

Switched Line/Hot

Line/Hot

NeutralNeutral

Neutral

Neutral

Ground

Ground

Green

120 V~60Hz or 277 V~60Hz

120 V~60Hz

Load

RF Local Controls

® SPECIF ICAT ION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Vive Designer-style: Maestro

369904h 16 08.27.18

Colors and Finishes

Gloss Finishes Satin Finishes

Metal Finish (wallplate only)

Stainless Steel SS

Taupe TP

Turquoise TQ

Plum PL

Merlot MR

Terracotta TC

Sienna SI

Midnight MN

Hot HT

Desert Stone DS

Eggshell ES

Biscuit BI

Snow SW

Palladium PD

Greenbriar GB

Bluestone BG

Mocha Stone MS

Goldstone GS

Stone ST

Limestone LS

White WH

Ivory IV

Almond AL

LightAlmond LA

Gray GR

Brown BR

Black BL

• Duetoprintinglimitations,colorsand finishes shown cannot be guaranteed to perfectly match actual product colors.

• Colorchipkeychainsareavailableformoreprecisecolormatching: GlossFinishes:DG-CK-1 SatinFinishes:SC-CK-1

When using Stainless Steel wallplates, it is recommended that you order the dimmer/switchinMidnight(MN).

)Lutron, Lutron, Maestro, Maestro Wireless, Clear Connect, Pico, Claro, Vive, and Satin Colors aretrademarksofLutronElectronicsCo.,Inc.,registeredintheU.S.andothercountries.

FASS,Hi-Power2•4•6,andRadioPowrSavraretrademarksofLutronElectronicsCo.,Inc.