Project Particulars L23/30

: Applied : Not applied

Turbocharger system (Plate no. 309)

309-1. Cleaning device for T/C (compressor side) a) Hand injector (for 5,6L23/30) --------------------------------------------- 309.25 Ed.03H b) Container (for 7,8L23/30) ------------------------------------------------- 512-05.00 Ed.01H

309-2. Charge air cooler with W.M.C (for fresh water) a) for 5,6L23/30 ----------------------------------------------------------------- 51201-04E b) for 7,8L23/30 ----------------------------------------------------------------- 51201-05E

309-3. Charge air cooler with W.M.C (for sea water) a) for 5,6L23/30 ----------------------------------------------------------------- 51201-06E b) for 7,8L23/30 ----------------------------------------------------------------- 51201-07E

309-4. Turbocharger system a) for 5,6L23/30 ----------------------------------------------------------------- 30901-16E b) for 7,8L23/30 ----------------------------------------------------------------- 30901-14E

309-5. Exhaust pipe arrangement a) for 5,6L23/30 ----------------------------------------------------------------- 30902-13E b) for 7,8L23/30 ----------------------------------------------------------------- 30902-14E

Control and safety system (Plate no. 313)

313-1. Remote sensors list a) Danfoss made --------------------------------------------------------------- 31308-02E b) Trafag made ------------------------------------------------------------------ 31308-02E1

Starting system (Plate no. 314)

314-1. Pressure reduction valve ----------------------------------------------- 51322-01E

Lubricating oil system (Plate no. 315)

315-1. Centrifugal by-pass filter ------------------------------------------------ 515.15 Ed.01H 515-15.00 Ed.01E 51515-01H

315-2. Prelubricating oil pump a) Rickmeier made ------------------------------------------------------------- 515-01.05 Ed.06H

51504-02H b) IMO made --------------------------------------------------------------------- 515-01.05 Ed.02E

51504-01H

315-3. Lub. oil hand wing pump ------------------------------------------------ 51525-01H

Fuel oil system (Plate no. 316)

316-1. Fuel oil feed pump -------------------------------------------------------- 31601-10H

Cooling water system (Plate no. 317)

317-1. Cooling water thermostatic valve a) Wax type ---------------------------------------------------------------------- 516.04 Ed.01H

516-04.00 Ed.01H 51604-01H

b) Pneumatic type (* refer to separate manual)

317-2. Pre-heater for fresh water ---------------------------------------------- 51635-01E

Page 1 (2)

----------------------- HHI/ENGINE AND MACHINERY DIVISION -----------------------

Project Particulars L23/30

Manual for auxiliary equipments (Part II)

1. Manual for turbocharger a) NR15/R (for 5,6L23/30) b) NR20/R (for 7,8L23/30)

2. Manual for Charge Air Cooler

3. Manual for governor a) Hydraulic type (UG8D) b) Electric type

4. Manual for remote sensors a) Press.sensor,Temp.switch Danfoss made Trafag made b) Temp.sensor (Resistance bulb) Daeyang made C.M.R. made Heriana made

5. Manual for special equipments

1) Resilient mounting a) Rubber Design BV b) Loggers

2) Flexible coupling

3) Torsional vibration damper

4) Oil mist detector Graviner MK-6 Schaller VN-115

5) Emergency MDO pump unit

6) Jacket water pre-heating unit

7) Cooling water thermostatic valve (Pneumatic type)

8) L.O.auto back-flushing filter

Page 2 (2)

----------------------- HHI/ENGINE AND MACHINERY DIVISION -----------------------

INSTRUCTION BOOK 6L23/30Hull No. HMD0322VOLUME ICoverProject Particulars301 Engine Data302 Operation of Engine303 Engine Performance and Condition304 Trouble Tracing305 Engine Frame and Bedplate Crankshaft and Main Bearings306 Cylinder Head and Cylinder Liner307 Piston and Connecting Rod308 Operating Gear for Inlet Valves, Exhaust Valves and Fuel lnjection Pumps309 Turbocharger System310 Fuel Injection Pump311 Fuel Injection312 Camshaft and Camshaft Drive313 Control and Safety Systems, Automatics and Instruments314 Starting System315 Lubricating Oil System, Specification and Treatment of Lubricating Oil316 Fuel- Oil System, Fuel and Fuel Treatment317 Cooling Water System, Treatment of Cooling Water318 Driven Machinery319 Tool

VOLUME II