11/99 N/** 6.6.020.01 Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. VP40 3 Way Proportional Pressure Control Valve Nominal diameter 2 Direct operated poppet valves Flange design ● Low hysteresis ● Good repeatability ● High flow capacity at exhaust port ● Manifold mountable system ● Compact design Technical Data Medium: Filtered air, lubricated or unlubricated, Filter 50 μm Operation: Proportional solenoid Connection: Flange, subplate Flow direction: Fixed Operating pressure p 1 : 16 bar max. Pressure setting p 2 : 0 to 16 bar Ambient temperature: -10 to +40 °C Hysteresis: < 3 % (IN, p 2 max) Repeatability: * < 1 % (p 2 max) Linearity: * See characteristic curve Response sensitivity: * ≤ 1 % (p 2 max) Degree of protection: IP 65 with connector Mounting: Any position Materials: Body aluminium alloy Seals NBR (Perbunan) *Values referred to 20 °C with dither 20 % IN, 50 Hz Ordering Information 3 way proportional pressure control valve, ND 2, pressure setting 0 to 10 bar, Type: 4090020.7093.012.00 Subplate must be ordered separately. 2 3 1 Connectors See data sheet 7503364 Symbol
Transcript
11/99 N/** 6.6.020.01Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
VP40
3 Way Proportional Pressure Control Valve
Nominal diameter 2Direct operated poppet valves
Flange design
Low hysteresis
Good repeatability
High flow capacity at exhaust port
Manifold mountable system
Compact design
Technical DataMedium:
Filtered air, lubricated or unlubricated,Filter 50 µm
*Values referred to 20 °C with dither 20 % IN, 50 Hz
Ordering Information3 way proportional pressure control valve, ND 2,pressure setting 0 to 10 bar,Type: 4090020.7093.012.00
Subplate must be ordered separately.
2
3 1
ConnectorsSee data sheet 7503364
Symbol
VP40 ND 2
N/** 6.6.020.02 11/99Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
General Information
Type Nominal diameter Connection Pressure Max. Operating Rated Current Drive WeightSetting p2 (bar) Pressure p1 (bar) (mA) Electronics (kg)
Type Rated Current Electrical connection Remarks Description(mA)
5980083 0 to 1000 Connector acc. to DIN 43651 Suitable for 4090020.70935980087 0 to 1000 2 m Cable and 4090021.7093 valves
5980118 0 to 2400 Connector acc. to DIN 43651 Suitable for 4090022.7093 valve
5980119 0 to 2400 2 m Cable
Plug-in type amplifier with constant currentregulator PDM. Degree of Protection: IP 65.Power supply: 18 to 32 V DC Residual ripple: ≤10 %.Ambient temperature: 0 to +50 °C.Mounting: Any position
Type Rated Current Remarks Description(mA)
5980126 0 to 2400 Suitable for 4090020.7093and 4090021.7093 valves
5980127 0 to 1000 Suitable for 4090022.7093 valve
Amplifier module with constant current regulatorPDM. Degree of Protection: IP 20.Power supply: 18 to 32 V DC Residual ripple: ≤10 %.Ambient temperature: 0 to +50 °C.Mounting: Any position.For attachment on mounting rail acc. to EN 50022
pQ12
Type Description Specification
0680003 Connector DIN 43650 Form B small
0014400 Silencer M5
Accessories
Data sheet 6.6.030
Data sheet 6.6.031
Type Rated Setpoint Ramps PID-controller for Remarks DescriptionCurrent (mA) Input closed loop contr.
5988020 0 to 2400 0 to ±10 V 4 no Suitable for valves4090XXX, 4088XXX
5988022 0 to 2400 0 to ±10 V 4 yes Suitable for valves4090XXX, 4088XXX
Digital amplifier module with constant currentregulator PDM.Power supply: 18 to 32 V DC Residual ripple: ≤10 %.Ambient temperature: 0 to +50 °C.Weight: 0,4 kg
pQ04
Data sheet 7503188
VP40 ND 2
11/99 N/** 6.6.020.03Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
Characteristic curves Flow characteristic for 7 bar operating pressure
6,0
p2 (bar)
(mA)
(mA)
(mA)
p2 = f (W)
5,4
4,8
4,2
3,6
3,0
2,4
1,8
1,2
0,6
0 115 230 345 460 575 690 805
0 150 300 450 600 750 900 1050
1400 15001000 1200800200 400 6000
10
9
8
7
6
5
4
3
2
1
0
16
14
12
10
8
6
4
2
0
p2 (bar)
Q (l/min)
p2 = f (Q) at p1 = 7 bar
6
5
4
3
2
1
0 80 160 240
Flow characteristic for 12 bar operating pressure Flow characteristic for 16 bar operating pressurep2 (bar)
Q (l/min)
p2 = f (Q) at p1 = 16 bar16
14
12
10
8
6
4
2
0 80 160 240 320 400 480
p2 (bar)
Q (l/min)
p2 = f (Q) at p1 = 12 bar10
8
6
4
2
0 80 160 240 320 400
VP40 ND 2
N/** 6.6.020.04 11/99Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
General Dimensions, Valve
16
25 36
12,5
19,5
32
75
244
32
4,3
424
M54,
23,8
2 1,1
5
27
1
2
1
2
3
Ø 6
,4 7,5
7,5
14
1 1(3) (3)
2
13Ø 7
,27
G1/8
8M
5
4,3
172432
24
32
M4x6 deep
G1 /
8
10
8
2,5
General Dimensions, Subplate
G 1/8 SubplateType: 0601740 to be ordered separately
Screw plug for open portType: 0568384 to be ordered separately
VP40 ND 2
11/99 N/** 6.6.020.05Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
22222
1(3) 1(3)
C4 C
B
A
16 33
Typ Description Weight (kg)
0601740 Single Subplate Assembly 0,04
0601741 Manifold bar – 2 Valves 0,08
0601742 – 3 Valves 0,13
0601743 – 4 Valves 0,17
0601744 – 5 Valves 0,21
0601745 – 6 Valves 0,24
0559301 Nipple -
0602005 Blind Plate Assembly 0,22
0568384 Screw Plug G 1/8 -
Components
Manifold system
3
2
2
2
2
1
Manifold bar
Blind plate
Nipple
Single subplate
Manifold bar, basic dimensions
Type No. of valves A B C
0601741 2 65 57 -
0601742 3 98 90 -
0601743 4 131 123 -
0601744 5 164 156 57
0601745 6 197 189 57
VP40 ND 2
N/** 6.6.020.06 11/99Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
Warning. Bores of mounting bracket must not be used for fastening of stacking system.
64,4
96,6
VP40 ND 2
11/99 N/** 6.6.020.07Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
Type Description Weight (kg)
0543862 Flange assembly 0,1supplied with screw, G 1/8
Components
Flanged System
Flange Assembly Dimensions
2 1
G1 /
8
G1 /
8
20
7
48
8
M4
7
10
9,5
2432 3
14,5 7
24
32
These products are intended for use in industrial compressed air systems only. Do notuse these products where pressures and temperatures can exceed those listed under‘Technical Data’.Before using these products with fluids other than those specified, for non-industrialapplications, life-support systems, or other applications not within publishedspecifications, consult NORGREN.Through misuse, age, or malfunction, components used in fluid power systems canfail in various modes. The system designer is warned to consider the failure modes of
all component parts used in fluid power systems and to provide adequate safeguardsto prevent personal injury or damage to equipment in the event of such failure.System designers must provide a warning to end users in the systeminstructional manual if protection against a failure mode cannot be adequatelyprovided.System designers and end users are cautioned to review specific warnings found ininstruction sheets packed and shipped with these products where applicable.
Warning
VP40 ND 2
N/** 6.6.020.08 11/99Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
11/99 N/** 6.6.022.01Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
VP40
3 Way Proportional Pressure Control Valve
Nominal diameter 4, 6 and 8Direct operated poppet valve
Port sizes G 1/8 - G 3/8, 1/8 NPT - 3/8 NPT
Low hysteresis
Good repeatability
High flow capacity at exhaust port
High response sensitivity
Fast response time
Technical DataMedium:
Filtered air, lubricated or unlubricated,Filter 40 µm
Operation:Proportional solenoid
Port Size:G 1/8 - G 3/8, 1/8 NPT - 3/8 NPTFemale thread
Flow direction:Fixed
Operating pressure p1:20 bar max.
Pressure setting p2:0 to 20 bar
Ambient temperature:-10 to +40 °C
Hysteresis: *< 3 % (lN max, p2 max)
Repeatability: *< 1 % (p2 max)
Linearity: *See characteristic curve
Response sensitivity: *< 1 % (lN max, p2 max)
Degree of protection:IP 65 with connector
Mounting:Any, preferably vertical
Material:Body aluminium alloySeals NBR (Perbunan)
* Values referred to 20 °C with dither 20% lN, 50 Hz
Ordering Information3 way proportional pressure control valve, ND 4,pressure setting 0 to 10 bar,port size G 1/4Type: 4088110.7053.012.00
Alternative ModelsWith thread connection NPT
ConnectorsSee data sheet 7503364
2
3 1
VP40 ND 4, 6, 8
N/** 6.6.022.02 11/99Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
General Information
Type Nominal diameter Port size Pressure Setting Max. Operating Rated Current Drive Weightp2 (bar) Pressure p1 (bar) lN (mA) Electronics (kg)
4088110.7053.012.00 4 G 1/8 0 to 10 10 0 to 1600 (1800) pQ11, pQ12, pQ04 0,8
4088218.7071.012.00 4 G 1/8 0 to 20 20 see data sheets 0,8
4088200.7053.012.00 6 G 1/4 0 to 2,1 7 7502961, 1,0
4088210.7053.012.00 6 G 1/4 0 to 10 12 7503109, 1,0
4088310.7071.012.00 8 G 3/8 0 to 7 10 7503188 1,2
Voltage 12 V DC
Limiting current IN 1840 mA
Rated power PN 22 W
Resistance R20 6,5 Ω ±3%
Duty cycle 100 %
Proportional Solenoids
Type Description Specification
0570275 Connector DIN 43650 Form A
Accessories
Drive ElectronicspQ11
Type Rated Current Electrical connection Remarks Description(mA)
5980081 0 to 2400 Connector acc. to DIN 43651 Suitable for valves5980085 0 to 2400 2 m Cable 4088XXX.XXXX
Plug-in type amplifier with constant currentregulator PDM. Degree of Protection: IP 65.Power supply: 18 to 32 V DC Residual ripple: ≤10 %.Ambient temperature: 0 to +50 °C.Mounting: Any position
Type Rated Current Remarks Description(mA)
5980126 0 to 2400 Suitable for valves4088XXX.XXXX
Amplifier module with constant current regulatorPDM. Degree of Protection: IP 20.Power supply: 18 to 32 V DC Residual ripple: ≤10 %.Ambient temperature: 0 to +50 °C.Mounting: Any position.For attachment on mounting rail acc. to EN 50022
pQ12
Data sheet 6.6.030
Data sheet 6.6.031
Type Rated Setpoint Ramps PID-controller for Remarks DescriptionCurrent (mA) Input closed loop contr.
5988020 0 to 2400 0 to ±10 V 4 no Suitable for valves4090XXX, 4088XXX
5988022 0 to 2400 0 to ±10 V 4 yes Suitable for valves4090XXX, 4088XXX
Digital amplifier module with constant currentregulator PDM.Power supply: 18 to 32 V DC Residual ripple: ≤10 %.Ambient temperature: 0 to +50 °C.Weight: 0,4 kg
pQ04
Data sheet 7503188
These products are intended for use in industrial compressed air systems only. Do notuse these products where pressures and temperatures can exceed those listed under‘Technical Data’.Before using these products with fluids other than those specified, for non-industrialapplications, life-support systems, or other applications not within publishedspecifications, consult NORGREN.Through misuse, age, or malfunction, components used in fluid power systems canfail in various modes. The system designer is warned to consider the failure modes of
all component parts used in fluid power systems and to provide adequate safeguardsto prevent personal injury or damage to equipment in the event of such failure.System designers must provide a warning to end users in the systeminstructional manual if protection against a failure mode cannot be adequatelyprovided.System designers and end users are cautioned to review specific warnings found ininstruction sheets packed and shipped with these products where applicable.
Warning
VP40 ND 4, 6, 8
11/99 N/** 6.6.022.03Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
Characteristic curvesType: 4088110
Type: 4088218
Type: 4088200
10
p2 (bar)
I (mA)
p2 = f (I)
9
8
7
6
5
4
3
2
1
0 200 400 600 800 1000 1200 1400 1600
10
p2 (bar)
Q (l/min)
p2 = f (Q)
9
8
7
6
5
4
3
2
1
0 160 320 480 640 800
p1 = 10 barp2 = adjusted at Q=0
p2 = 10 bar
p2 = 8 bar
p2 = 6 bar
p2 = 4 barp2 = 2 bar
20
p2 (bar)
I (mA)
p2 = f (I)
18
16
14
12
10
8
6
4
2
0 200 400 600 800 1000 1200 1400 18001600
p2 (bar)
Q (l/min)
p2 = f (Q)
6
8
10
12
14
16
18
20
4
2
0 320 640 960 1280 20801600 1920
p1 = 20 barp2 = adjusted at Q=0
p2 = 6 barp2 = 2 bar
p2 = 8 bar
p2 = 10 bar
p2 = 12 bar
p2 = 14 bar
p2 = 16 bar
p2 = 18 bar
p2 = 20 bar
2,02,1
p2 (bar)
I (mA)
p2 = f (I)
1,8
1,6
1,4
1,2
1,0
0,8
0,6
0,4
0,2
0 200 400 600 800 1000 1200 1400 1600
2
p2 (bar)
Q (l/min)
p2 = f (Q)
1,5
1
0,5
0 160 320 480 640 800
p1 = 7 barp2 = adjusted at Q=0
p2 = 1 bar
p2 = 2 bar
p2 = 1,5 bar
p2 = 0,5 bar
VP40 ND 4, 6, 8
N/** 6.6.022.04 11/99Our policy is one of continued research and development. We therefore reserve the rightto amend, without notice, the specifications given in this document.
