4 3 2 11 8 7 6 10 1 5 3 2 9 Parts Overview The Unit 1 On/Off Button Insert the plug into the electrical outlet. Press the on/off switch on the top of the vacuum cleaner, to switch the vacuum cleaner on and press the button again to turn the vacuum cleaner off. 2 Dirt Container Locked onto the top of the unit. 3 Cyclone Separator Located inside of the Dirt Container. 4 Dirt Container and Carry Handle Use the carry handle located on the side of the dirt bin to move the vacuum cleaner from room to room. 5 Dirt Container Release Button Press the button on the top of the dirt container. The dirt container can then be lifted and removed off the unit. 6 Auto Cord Rewind To rewind the power cord, press the cord rewind button, located on the top of the vacuum cleaner. 7 Floor Tool Parking Slot For convenience there is a parking slot located at the rear of the vacuum cleaner where the Floor Tool can be parked for carrying and storage. 8 Plug 9 Dirt Bin Quick Release Button Hold the dirt container over a bin and press the release button. 10 Pre-Motor Filter Cover Located inside the lid of the dirt bin container. 11 Hose Inlet 12 Post Motor Filter Cover Located on the base of the unit. Retain this guide for future reference. MACH MACH 1 1 Bagless cylinder Vax model number: VZL-7071SERIES VZL-7011SERIES GB instruction manual Vax careline 0870 6061248 www.vax.co.uk What is your vax’s serial number? Note this down in case you need it in future (on the base of your cleaner) What is your vax’s model number? V Z L 12 - Vax VZL-7071 User Guide v3.qxd:Vax VZL-7071 18/9/08 12:01 Page 1
Transcript
4
3
2
11
8
7
6
10
1
5
3
2 9
Parts Overview
The Unit
1 On/Off ButtonInsert the plug into the electrical outlet. Press theon/off switch on the top of the vacuum cleaner, toswitch the vacuum cleaner on and press the buttonagain to turn the vacuum cleaner off.
2 Dirt ContainerLocked onto the top of the unit.
3 Cyclone SeparatorLocated inside of the Dirt Container.
4 Dirt Container and Carry HandleUse the carry handle located on the side of the dirtbin to move the vacuum cleaner from room to room.
5 Dirt Container Release ButtonPress the button on the top of the dirt container. Thedirt container can then be lifted and removed off theunit.
6 Auto Cord RewindTo rewind the power cord, press the cord rewindbutton, located on the top of the vacuum cleaner.
7 Floor Tool Parking SlotFor convenience there is a parking slot located at therear of the vacuum cleaner where the Floor Tool canbe parked for carrying and storage.
8 Plug9 Dirt Bin Quick Release Button
Hold the dirt container over a bin and press therelease button.
10 Pre-Motor Filter CoverLocated inside the lid of the dirtbin container.
11 Hose Inlet12 Post Motor Filter Cover
Located on the base of the unit.
Retain this guide for future reference.
MACHMACH1111Bagless cylinder
Vax model number:VZL-7071SERIES VZL-7011SERIES GBinstruction manual
Vax careline 0870 6061248
www.vax.co.uk
What is your vax’s serial number?
Note this down in case you need it in future
(on the base ofyour cleaner)
What is your vax’s model number?
V Z L
12
-
Vax VZL-7071 User Guide v3.qxd:Vax VZL-7071 18/9/08 12:01 Page 1
www.vax.co.uk
13
12a
14
15
16
17
The Accessories
12 2-in-1 Toola. Dusting Brush: For delicate surfaces.b. Upholstery Tool: For carpet, upholstery and stairs etc.
13 Crevice ToolFor crevices, corners and cracks.
14 Combination Floor Tool (Not inc. on model VZL-7011AT)For carpet and rug cleaning: Press the rocker switchon the Combination Floor Head to raise the brushes.For hard floor cleaning: Press the rocker switch on theCombination Floor Head to lower the brushes.
15 Telescopic TubeThe telescopic tube can be lengthened or shorted bypushing the button in and sliding the tube apart ortogether as required.
16 TurboTool (VZL-7071P, VZL-7071S, VZL-7071AT and VZL-7071E only)
For pet hair, stair and upholstery cleaning.NOTE: Do not use the Turbo Tool on suede andleather surfaces.
17 HoseTool caddy on handle for tool storage.
18 Stretch Hose (VZL-7071S only)For full height stair cleaning.NOTE: This should not be used as the main hose. Thestretch hose is recommended to be used for staircleaning. The unit should always be positioned at thebottom of the stairs
19 Hard Floor Tool (VZL-7011AT only)For parquet and laminate flooring.
20 Turbo BrushNOTE: Not recommended for hard floors.For large carpeted areas.
12b 18
20
21 22 23
Parts Overview
To replace or purchase parts for your vacuumcleaner, please visit our website:
www.vax.co.uk
If your Vacuum Cleaner or Accessories are Damaged/FaultyPlease Call our Vax Careline on: 0870 6061248
IMPORTANT: The condition of the filters affects theperformance of your vacuum cleaner. Please check and washfilters periodically (depending on level of use). For full cleaninginstructions see page 6.
2 parts overview
19
Replacement filter kits are available at www.vax.co.uk
!
Vax VZL-7071 User Guide v3.qxd:Vax VZL-7071 18/9/08 12:01 Page 2
Vax Careline 0870 606 1248
2. Safety InformationFor Household Use Only
When using the vacuum cleaner, basic safety precautionsshould always be observed, including the following:
1. Only use the vacuum cleaner indoors on drysurfaces.
2. Turn off the vacuum cleaner controls beforeconnecting or disconnecting from the mains supply.
3. Always unplug the vacuum cleaner beforeconnecting or disconnecting the vacuum hose andaccessories.
4. Children should be supervised to ensure that theydo not play with the appliance.
5. The appliance is not intended for use by persons(including children) with reduced physical, sensory ormental capabilities, or lack of experience andknowledge, unless they have been given supervisionor instruction concerning use of the appliance by aperson responsible for their safety.
6. Use only as described in this manual.Use only the manufacturer’s recommendedattachments.
7. Do not use the vacuum cleaner if it has beendropped, damaged, left outdoors or dropped intowater. Do not use the vacuum cleaner with adamaged cord or plug. If the supply cord or plug isdamaged, return the vacuum cleaner to a VaxAuthorised Service Agent or suitably qualifiedperson for examination, repair or adjustment.
8. Do not pull or carry by the cord. Do not use the cordas a handle, close a door on the cord or pull the cordaround sharp edges or corners. Do not run thevacuum cleaner over the cord. Keep the cord awayfrom heated surfaces.
9. Do not handle the plug or vacuum cleaner with wethands. Do not use outdoors or on wet surfaces.
10. Do not put any objects into openings. Do not usewith any openings blocked and do not restrict airflow. Keep all openings free of dust, lint, hair oranything that may reduce airflow.
11. Keep hair, loose clothing, fingers and all parts of thebody away from openings and moving parts.
12. Do not pick up hot coals, cigarette butts, matches orany hot, smoking or burning objects.
13. Do not pick up flammable or combustible materials(lighter fluid, petrol, kerosene, etc) or use in thepresence of explosive liquids or vapours.
14. Do not vacuum up harmful or toxic material (chlorinebleach, ammonia, drain cleaner, etc).
15. Do not vacuum up hard or sharp objects such asglass, nails, screws, coins, etc.
16. Do not use without the filters in place.
17. Take extra care when vacuuming on stairs.
18. Keep vacuuming area well lit.
19. Store the vacuum cleaner indoors in a cool, dry area.
20. Turn off the on/off switch before unplugging thevacuum cleaner.
21. Use only CE-approved 13 amp extension cords. Non-approved extension cords may overheat. Care shouldbe taken to arrange the cord so that the cord cannotbe pulled or tripped over.
WARNING: Always switch off and unplug thevacuum cleaner from the electrical outlet
before assembling, opening or emptying the dirtcontainer, or before connecting/disconnecting theattachments.
CAUTION: The vacuum cleaner is a verypowerful unit. Before plugging the cord into
the electrical outlet, make sure the switch is in the‘off’ position.
IMPORTANT: If the inlet, hose or telescopictube is blocked, switch off the vacuum cleaner
and remove the blockage(s) before re-starting thevacuum cleaner.
IMPORTANT: Cleaning filters prolongs the lifeof the machine and improves vacuum cleaner
performance. Make sure all the filters are completelydry before inserting back into the vacuum cleaner.
This vacuum cleaner is intended for household use onlyand not for commercial or industrial use.
!
!
!
!
Motor ThermostatIMPORTANT: The motor is equipped with athermal cut-out. If for any reason, the vacuum
cleaner should over-heat, the thermostat willautomatically turn the unit off. Should this occur,unplug the vacuum cleaner from the electrical outletand turn off the switch. Remove the dirt containerand empty. Clean the filters. Allow the cleaner to coolfor approximately one (1) hour. To re-start, plug intoan electrical outlet and switch back on.
!
d/Faulty48
7011S only)
washeaning
3safety information
Vax VZL-7071 User Guide v3.qxd:Vax VZL-7071 18/9/08 12:01 Page 3
www.vax.co.uk
4 assembly / operation
12 13 16 14
CLICK!
WARNING: Always switch off and unplug thevacuum cleaner from the electrical outlet before
assembling, opening or emptying the dirt container, orbefore connecting/ disconnecting the attachments.
NOTE: Fully unwind the power cord. A yellow mark on thepower cord indicates the recommended cord length. Donot exceed the cord length beyond the red mark.
3. Assembling your vacuum cleaner
Choose the attachment
4. Operating the appliance
Packing away and storage
IMPORTANT: Always unplug the vacuum from the electricaloutlet and rewind the power cord as directed before storing.
NOTE: When rewinding the power cord, guide the cordwith one hand, This will prevent the cord from whippingwhich could cause damage or injury.
NOTE: For convenience there is a parking slot located atthe rear of the vacuum cleaner where the floor tool andhose can be parked for carrying and storage.
!
!
17
17 15
CLICK!
15
15
14
Vax VZL-7071 User Guide v3.qxd:Vax VZL-7071 18/9/08 12:01 Page 4
5
Vax Careline 0870 606 1248
dirt container & filters
5. Dirt ContainerRemoval and replacement
Emptying the Dirt Container
Cleaning the Cyclone Separator
Clearing Blockages
CLICK! CLICK!
IMPORTANT : Do NOTuse the vacuum without ALLof the filters in place.
IMPORTANT: Vax recommends cleaning the filtersevery time the Dirt Container [1] is emptied for
consistent performance of your machine.
IMPORTANT : Always switch off and unplug thevacuum cleaner from the electrical outlet before
removing the Dirt Container.
NOTE: Do not use any detergents or boiling water to washthe filters.
IMPORTANT: Remove the Dirt Container[1] from theunit and dispose of the dirt inside the container
before cleaning.
IMPORTANT : The cyclone separator should not besubmerged in water.! !
WARNING : To reduce the risk of electric shock,the power cord must be disconnected before
performing maintenance/ troubleshooting checks.Turnthe vacuum cleaner off and unplug from the electricaloutlet.
!
Hose Blockages
The flexible hose may be disconnected from the vacuumcleaner by pressing the clip on the connector and pullingaway from the machine. Carefully remove any blockagesfound and reconnect the hose securely.
Accessory Blockages
Remove the accessory from the cleaner. Carefully removethe blockage and return to the cleaner.
!
!
!
Vax VZL-7071 User Guide v3.qxd:Vax VZL-7071 18/9/08 12:02 Page 5
www.vax.co.uk
6 dirt container & filters
6. The FiltersCleaning the Pre- Motor Filter
Cleaning the Post- Motor Filter NOTE : This is located at the base of the vacuum cleaner.
7. Cleaning Blockages
Cleaning Debris from the Turbo Tool (VZL-7071P, VZL-7071S, VZL-7071AT and VZL-7071E only)
NOTE : Switch the cleaner off and disconnect the power plug from the electrical outlet.
Removing debris from the TurboBrush (VZL-7011AT)
IMPORTANT: Your vax vacuumcleaner is fitted with high
performance filters it is essential thatthese are well maintained and cleanedaccording to the following instructions.
Vax recommends that the pre- andpost-motor filter should be checked andcleaned periodically depending on thefrequency of use and the volume of dirtbeing picked up on each occasion.
NOTE : Both Pre- and Post-Motor Filterscan be rinsed in warmwater (max 40°C).Allow to air dry for 24 hours beforereplacing. Do NOTuse any detergents orboiling water to wash the filters.
!
Once completely dry, return the pre-motor filters and case to the vacuum cleaner. Replace the pre-motor filter coverbefore restarting the vacuum cleaner.
24
24
The brushbar will stop rotating if it is blocked during operation by vacuuming upforeign objects, or if strands of carpet are wrapped around it.
Switch the vacuum cleaner off and disconnect the power plug from the electricaloutlet.
Lay the TurboBrush floor head on a flat surface and turn over to expose thebrushbar. Using a pair of scissors, cut through any threads or hairs caught by thebrushbar that have wrapped around the guides.
Hose Blockages
The flexIble hose may be disconnected from the vacuumcleaner. Carefully remove any blockages found andreconnect hose securely.
Accessory Blockages
Remove accessory from hose handle/ tube. Carefullyremove the blockage and return to the cleaner.
TAP
TAP
Vax VZL-7071 User Guide v3.qxd:Vax VZL-7071 18/9/08 12:02 Page 6
7
Vax Careline 0870 606 1248
FAQ/ service / specification
WARNING: to reduce the risk of personal injury, unplug the vacuum cleaner before performingmaintenance/troubleshooting checks
!
8. FAQs
Is there an accessory missing?
• check the ‘Parts Overview’ page in this guide to makesure that the part is definitely included with your unit.
• If it is missing, please call our Vax Careline to order areplacement: 0870 606 1248 or visitwww.vax.co.uk toorder online.
Why won’t the vacuum cleaner pick up?
• The filters may be clogged: Refer to ‘The Filters’ (Page 6).
• The Dirt Container is full or blocked: Refer to ‘DirtContainer: Removal and replacement’ (Page 5).
• The Dirt Container may be incorrectly installed: Refer to‘Dirt container: Removal and replacement’ (Page 5).
Why is dust escaping from the vacuum?
• The filters may not be installed correctly. Refer to ‘TheFilters: Removal and replacement’ (Page 6).
• The Dirt container may be incorrectly installed: Removethe Dirt Container from the unit by pressing the DirtContainer Release Button (5) and reattach it to the unit,ensuring it is locked firmly back into place.
• The filters may be clogged: Refer to‘The Filters’ (Page 6).
What do I do if an accessory/the unit becomesdamaged or broken?
• Visit www.vax.co.uk for parts and spares.
• Please call our Vax careline to purchase new spares ororder a replacement: 0870 606 1248
why won’t the accessories pick up properly?
• The accessory may be blocked: Refer to ‘CleaningBlockages’ (Page 6).
• The accessory may be faulty: call ourVax Careline to order a replacement:0870 606 1248
Why will the vacuum cleaner not run?
• It may not be plugged into the electrical outlet correctly:Ensure that the plug is pushed into the electrical outletsecurely.
• The electrical outlet may not be working: Check the fuseor breaker and consult an electrician.
• The motor Thermostat may have tripped: Switch off andunplug the vacuum cleaner. Leave for one hour beforeswitching the vacuum cleaner back on.
If none of these questions apply to you, or for furtherassistance please call our Vax Careline team on:
0870 606 1248
9. UK Service & HelpVax Care 0870 6061248Monday-Friday 8.00am to 8.00pmSaturday-Sunday 9.00am to 5.00pm
Please make a note of the model number and serialnumber of your Vax before calling. There are over 400approved Vax Service Agents in the UK. For the nearestVax Service Agent, please call the Vax Careline or visitwww.vax.co.uk
Waste electrical products should not be disposed of with household waste. Please recycle wherefacilities exist. Check with your Local Authority or retailer for recycling advice.
