+ All Categories
Home > Documents > Wardrobe Fitting

Wardrobe Fitting

Date post: 30-May-2018
Category:
Upload: jannarcha
View: 225 times
Download: 0 times
Share this document with a friend
14
Wardrobe Fittings    W   a   r    d   r   o    b   e    F    i    t    t    i   n   g   s
Transcript

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 1/14

Wardrobe Fittings

W a r d r o b e

F i t t i n g s

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 2/14

124

Special Features

1. Refer drilling dimensions for cabinet & shutters. (Ref. Fig. 1 & 2).2. Fit the Runner track Guide track as required and screw them as shown.

(Ref. Fig.2 & 2A).3. Fit click on / slip on Hinges (not provided) on one side of the shutter (Ref. Fig,3),

Using Ø35 mm boring cutter.4. Fit the Folding Hinges in between the two shutters (Ref. Fig.3 & 3A) Template is

provided for drill holes for the Folding Hinges. (Ref. Fig,3B).5. Fit Hinged Runner with Quick release and Hinged Guide with Quick release to the

far side of second shutter. (Ref. Fig,3A), Using Ø35 mm boring cutter.6. Screw the Click on / Slip on hinge on to the Mounting plate which is fitted on the

inside of the cabinet. (Ref. Fig.4).7. Bring second shutter close to the first shutter (Ref. Fig.5) and push U Pin to engage.

(Ref. Fig.5A).8. Fold the shutters and engage roller into Runner Track Guide Track by pushing quick

release (Ref.Fig.6) Shutters can also be disengaged by pulling quick release down.

! Ergonomically designed for overlay sliding shutters, Bottom Guide Track is hidden.! Manufactured out of durable plastics.! High precision rolling.! Quick release mechanism provided.!

Templates provided for drilling.

Hi - Fold Fittings 200

Specifications

Code No.Item Max. Widthof EachShutter

Hi -Fold Fittings

Runner Track

Guide Track

HFF 200

HFF - RT

HFF - GT

500MM

Max. Weightof EachShutter

10 Kgs.

Fitting Instructions

Des. Reg. no. 205457

HINGED RUNNERWITH QUICK RELEASE

FOLDINGHINGE

HINGED GUIDEWITH QUICK RELEASE

* Click-on Hinge or Slip-on Hinge are not included

RUNNER TRACK

HINGED GUIDEWITH QUICK

RELEASE

CLICK ON HINGE (OVERLAY)*SLIP ON HINGE (OVERLAY)

(4 Nos)SINGLE HINGEDRUNNER WITHQUICK RELEASE

GUIDE TRACK

FOLDINGHINGE

Fig. 1

Calculation for door width/door panelsDoor width = inside cabinet width + (2 x overlay)Door panel width = inside cabinet width - A

+ (2 x overlay) / 2

For overlay more than 10 mm,C value = (overlay - 10) + 4

For min. overlay 10 mm,C value = 4 mm

'A'1.02.03.04.05.0

'B'15.515.014.514.013.5

31.0 32.0 15.0'A'

3 2

. 0 3 2

. 0

4.0

4 5

. 0 'B'

C

Ø 3 5

. 0

1 2 d e e p

'B'

Ø 3 5 .0 1 2 d e e p

Shutter Drilling Dimensions Fig. 2 Fig. 2A

30.025.5

CABINET 4 6

. 0

SHUTTER25.0

2 6

. 0

5 5

. 0 M i n

.

1 5

. 0 M i n

.

Side View of cabinet

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 3/14

125

Fig. 3

Fig. 5 Fig. 6

RUNNER TRACK

PUSH QUICK RELEASETO ENGAGE

IN THE TRACK

PUSH QUICK RELEASETO ENGAGE

IN THE TRACK

GUIDE TRACK

Fig. 3A

2.0

5.0

3 2

. 0

32.0

0 Ø 5

.

Fig. 3B Fig. 4

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 4/14

126

1. Refer drilling dimensions for cabinet & shutters. (Ref. Fig. 1 & 2).2. Fit the Runner track Guide track as required and screw them as shown. (Ref. Fig.2 &

2A).3. Fit click on / slip on Hinges (not provided) on one side of the shutter (Ref. Fig,3),

Using Ø35 mm boring cutter.4. Fit the Folding Hinges in between the two shutters (Ref. Fig.3 & 3A) Template is provided

for drill holes for the Folding Hinges. (Ref. Fig,3B).5. Fit Hinged Runner with Quick release and Hinged Guide with Quick release to the far

side of second shutter. (Ref. Fig,3A), Using Ø35 mm boring cutter.6. Screw the Click on / Slip on hinge on to the Mounting plate which is fitted on the

inside of the cabinet. (Ref. Fig.4).7. Bring second shutter close to the first shutter (Ref. Fig.5) and push U Pin to engage.

(Ref. Fig.5A).8. Fold the shutters and engage rollers into Runner Track Guide Track by pushing quick

release (Ref. Fig. 6) Shutters can also be disengaged by pulling quick release down.

! Ergonomically designed for overlay sliding shutters, Bottom Guide Track is hidden.! Manufactured out of durable plastics.! High precision rolling.! Quick release mechanism provided.!

Templates provided for drilling.

Hi - Fold Fittings 300

Special Features

Specifications

Code No.Item Max. Widthof EachShutter

Hi -Fold Fittings

Runner Track

Guide Track

HFF 300

HFF - RT

HFF - GT

500MM

Max. Weightof EachShutter

20 Kgs.

Fitting Instructions

Des. Reg. no. 205457

HINGED RUNNERWITH QUICK RELEASE

FOLDINGHINGE

HINGED GUIDEWITH QUICK RELEASE

* Click-on Hinge or Slip-on Hinge are not included

RUNNER TRACK

HINGED GUIDEWITH QUICK

RELEASE

CLICK ON HINGE (OVERLAY)*SLIP ON HINGE (OVERLAY)

(4 Nos)DOUBLE HINGEDRUNNER WITH

QUICK RELEASE

GUIDE TRACK

FOLDINGHINGE

Fig. 1

Calculation for door width/door panelsDoor width = inside cabinet width + (2 x overlay)Door panel width = inside cabinet width - A

+ (2 x overlay) / 2

For overlay more than 10 mm,C value = (overlay - 10) + 4

For min. overlay 10 mm,C value = 4 mm

'A'1.02.03.04.05.0

'B'15.515.014.514.013.5

31.0

Ø 3 5

. 0

1 2 d e e p

32.0 15.0

3 2

. 0

3 2

. 0 3 2

. 0

4 5

. 0

4.0

'A'

C

'B'

'B'

Ø 5 .3 0 2 d e

1 e p

Shutter Drilling Dimensions Fig. 2 Fig. 2A

30.025.5

4 6

. 0

6 4

. 0

CABINET

25.0 2 6

. 0

5 5

. 0 M i n

.

1 5

. 0 M i n .Side View of Cabinet

SHUTTER

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 5/14

127

Fig. 3 Fig. 3A

2.0

5.0

3 2

. 0 . Ø 5

0

32.0

Fig. 3B Fig. 4

Fig. 5A PUSH U PIN TO ENGAGE

Fig. 5 Fig. 6

RUNNER TRACK

PUSH QUICK RELEASETO ENGAGE

IN THE TRACK

GUIDE TRACK

PUSH QUICK RELEASETO ENGAGE

IN THE TRACK

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 6/14

128

Wardrobe Rail Fittings

1. Drill 2 holes on each internal side of wardrobe.2. First hole should be 24mm from the top internal face of

cabinet and centre distance to be 32mm apart. (Refer fig.1)3. Holes should be at equal height.

Fitting Instructions

Fig. 1

32.0

24.0

Oval Rail

Coat Hook

Rail Centre Support

Bracket

Special Features

! These oval wardrobe rail supports are die cast for strength and long life.! Easy to fit and compatible with a special oval rail.! Wardrobe rails are available in S.S 304 polished.! Coat hooks are also available.! System 32 compatible.! Rail centre supports are elegantly designed, manufactured out of Zinc alloy for strength and

increasing the load bearing capacity of wardrobe rails.

# Add 'B' or 'G' for Black or Silver Grey.

Length(mtr)Code Nos. FinishItem

1

2

WRF - R1A

WRF - R2A Aluminium AnodizedRail

-WRF - CH# Nylon Black or Silver GreyCoat Hook

-WRF - B1 Nickel PlatedBracket

-WRF - RS1 Nickel PlatedRail Centre Support

Specifications

1

2

WRF - R1S

WRF - R2SSS 304 Polished

Rail

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 7/14

129

Wardrobe Lift -Side Mount

Special Features

! Having twin arm construction for strength.! Ideal for tall cupboards or shop wall displays.! Shirts, dresses, suits can easily be pulled

down for easy access or stored conveniently

out of the way.! Load capability is 10 kgs. Max.

Specifications

WLSM 1Code No.

1. Screw the Base Bracket to the side wall with the screws provided. (Ref. Fig.1).2. Insert the Base onto the Base bracket through the track provided in the Base (Ref. Fig.2).

3. Join Main pole with the Hanging pole by using the screw provided. Max. adjustment ofHanging pole is 240.0 mm (Ref. Fig.3).

4. Fit the Handle to Main pole with the screw provided (Ref. Fig.4).5. Pull the leg of system down and join with Hanging pole assembly by using End brackets

and screws provided (Ref. Fig.5).6. Internal cabinet width - 860 (34") Min. & 1100 (43.5") Max.

Fitting Instructions

Caution

1. Fit the Right and Left systems parallel to each other.2. While pulling the Main pole ensure that it is lying in the middle of the Hanging pole.

Fig. 1

Base Bracket

Fig. 3

M 2 4 0. 0 a x.

T t a l A d j u s t m e n t

oHanging Pole

Fig. 6 Pull to access

Fig. 2 Base

Fig. 4

Main polewith handle

Fig. 5

End Bracket

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 8/14

130

Wardrobe Lift -Wall Mount

Special Features

1. Screw the Base plate to the wall with the screws and wall plugs provided (Ref. Fig.1).2. Insert the Base onto the Base plate through the track provided in the Base (Ref. Fig.2).

3. Join Main pole with the Hanging pole by using the screw provided. Max. adjustment ofHanging pole is 240.0 mm (Ref. Fig.3).

4. Fit the Handle to Main pole with the screw provided (Ref. Fig.4).5. Pull the leg of Base down and join with Hanging pole assembly by using End brackets

and screws provided (Ref. Fig.5).6. Angle adjustment support provided for maintaining the gap from wall (Ref. Fig.6).

Fitting Instructions

! Having twin arm construction for strength.! Ideal for tall cupboards or shop wall displays.! Shirts, dresses, suits can easily be pulled

down for easy access or stored conveniently

out of the way.! Load capability is 10 kgs. max.

Specifications

WLWM 1Code No.

Fig. 1

Base plate

Fig. 2

Base

Fig. 6

Angle Adj. Support

Pull to accessFig. 5

End Bracket

Fig. 4

Main pole

with handle

Fig. 3

Hanging Pole

2 4 0. 0 M a x.

T t a u t t o l A d j s

m e n

Caution

1. Fit the Base parallel to each other.2. While pulling the Main pole ensure that it is lying in the middle of the Hanging pole.

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 9/14

131

Trouser & Sari Pullout

Fig. 1

Fig. 3

FIT RODSINTO HOLES(10 Nos)

Fig. 2

Fitting Diagram ForTrouser And Sari Pullout

FRONT VIEW

Inner slide

Base plate

Housing

Code No. CR TS 1

1. Pullout comes in disassembled condition and can be easilyassembled with 2 screws provided to the moving ball bearingslide, through the holes provided in the housing after aligningwith the inner slide. (Refer fig. 1).

2. Trouser and Sari Pullout, left hand or right hand screwassembly is common (Refer fig. 2).

3. The trouser rods are inserted, facing forward. Insert the rodwith handle in the first hole near the slide to pull out easily.(Refer fig 3).

4. Cabinet internal dimensions required -Min. Width = 500 mm, Min. Depth = 520 mm.

Fitting Instructions

! Precision ball bearings used for smooth easy movement.! Rods are manufactured out of SS 304 and have

protective plastic sleeves.! System 32 compatible.

Special Features

Specifications

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 10/14

132

Fig. 2

Housing

Inner slide

Base plate FRONT VIEW

Fitting Diagram ForTie And Belt Pullout

Fig. 1

! Precision ball bearings used for smooth easy movement.! Rods are manufactured out of SS 304 and have protective

plastic sleeves.! System 32 compatible.

1. Pullout comes in disassembled condition and can be easilyassembled with 2 screws provided to the moving ball bearingslide, through the holes provided in the housing after aligningwith the inner slide. (Refer fig. 1)

2. Tie & Belt Pullout left hand or right hand screw assembly iscommon. (Refer fig. 2)

3. Cabinet internal dimensions required -Min. Width = 200 mm, Min. Depth = 520 mm.

Code No. CR TB 1

Fitting Instructions

Special Features

Specifications

Code No. TH12

! Elegantly designed.! Made out of SS 304.! Easy to use and fits on the

inside of any cupboard.! Special Clip provided for prevents the movements of

Holder. (Refer fig.1)! Also available with Nickle Plated Die cast brackets.

Special Features

SpecificationsFig. 1

Tie & Belt Pullout

Tie & Belt Holder

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 11/14

133

Tie Rack

Trouser Rack

1. Screw the base of the Tie rack on the cabinet at the distance of 60 mm from the front edge. (Ref. Fig.1)2. Min. cabinet internal depth - 500mm.

Fitting Instructions

Specifications

TIR 1Code No.

Special Features! A pullout rack which is easy to install, ergonomically

designed and above all durable.! Manufactured out of aluminum and plastic.! It can hold over 16 ties and even has a special tray to

keep small articles.

Fig.1

64.0

Front edgeof Cabinet

Side View

60.0Min.

6 2

. 0

1. Screw the base of the Tie rack on the cabinet at thedistance of 60 mm from the front edge. (Ref. Fig.1)

2. Pull the rack to fold to save space. (Ref. Fig.2)3. Min. cabinet internal depth - 500mm.

Fitting Instructions

! A pullout rack which is easy to install, ergonomically

designed and above all durable.! Manufactured out of aluminum and plastic.! It can hold trousers and sarees.! It can be folded down to save space.

Special Features

Specifications

TRR 1Code No.Fig.1 Side View

60.0Min.

Front edgeof Cabinet

6 2

. 0

Fig.2

Pull to fold

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 12/14

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 13/14

8/9/2019 Wardrobe Fitting

http://slidepdf.com/reader/full/wardrobe-fitting 14/14

136

Notes


Recommended